Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * abituguru.c Copyright (c) 2005-2006 Hans de Goede <hdegoede@redhat.com>
4 */
5/*
6 * This driver supports the sensor part of the first and second revision of
7 * the custom Abit uGuru chip found on Abit uGuru motherboards. Note: because
8 * of lack of specs the CPU/RAM voltage & frequency control is not supported!
9 */
10
11#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
12
13#include <linux/module.h>
14#include <linux/sched.h>
15#include <linux/init.h>
16#include <linux/slab.h>
17#include <linux/jiffies.h>
18#include <linux/mutex.h>
19#include <linux/err.h>
20#include <linux/delay.h>
21#include <linux/platform_device.h>
22#include <linux/hwmon.h>
23#include <linux/hwmon-sysfs.h>
24#include <linux/dmi.h>
25#include <linux/io.h>
26
27/* Banks */
28#define ABIT_UGURU_ALARM_BANK 0x20 /* 1x 3 bytes */
29#define ABIT_UGURU_SENSOR_BANK1 0x21 /* 16x volt and temp */
30#define ABIT_UGURU_FAN_PWM 0x24 /* 3x 5 bytes */
31#define ABIT_UGURU_SENSOR_BANK2 0x26 /* fans */
32/* max nr of sensors in bank1, a bank1 sensor can be in, temp or nc */
33#define ABIT_UGURU_MAX_BANK1_SENSORS 16
34/*
35 * Warning if you increase one of the 2 MAX defines below to 10 or higher you
36 * should adjust the belonging _NAMES_LENGTH macro for the 2 digit number!
37 */
38/* max nr of sensors in bank2, currently mb's with max 6 fans are known */
39#define ABIT_UGURU_MAX_BANK2_SENSORS 6
40/* max nr of pwm outputs, currently mb's with max 5 pwm outputs are known */
41#define ABIT_UGURU_MAX_PWMS 5
42/* uGuru sensor bank 1 flags */ /* Alarm if: */
43#define ABIT_UGURU_TEMP_HIGH_ALARM_ENABLE 0x01 /* temp over warn */
44#define ABIT_UGURU_VOLT_HIGH_ALARM_ENABLE 0x02 /* volt over max */
45#define ABIT_UGURU_VOLT_LOW_ALARM_ENABLE 0x04 /* volt under min */
46#define ABIT_UGURU_TEMP_HIGH_ALARM_FLAG 0x10 /* temp is over warn */
47#define ABIT_UGURU_VOLT_HIGH_ALARM_FLAG 0x20 /* volt is over max */
48#define ABIT_UGURU_VOLT_LOW_ALARM_FLAG 0x40 /* volt is under min */
49/* uGuru sensor bank 2 flags */ /* Alarm if: */
50#define ABIT_UGURU_FAN_LOW_ALARM_ENABLE 0x01 /* fan under min */
51/* uGuru sensor bank common flags */
52#define ABIT_UGURU_BEEP_ENABLE 0x08 /* beep if alarm */
53#define ABIT_UGURU_SHUTDOWN_ENABLE 0x80 /* shutdown if alarm */
54/* uGuru fan PWM (speed control) flags */
55#define ABIT_UGURU_FAN_PWM_ENABLE 0x80 /* enable speed control */
56/* Values used for conversion */
57#define ABIT_UGURU_FAN_MAX 15300 /* RPM */
58/* Bank1 sensor types */
59#define ABIT_UGURU_IN_SENSOR 0
60#define ABIT_UGURU_TEMP_SENSOR 1
61#define ABIT_UGURU_NC 2
62/*
63 * In many cases we need to wait for the uGuru to reach a certain status, most
64 * of the time it will reach this status within 30 - 90 ISA reads, and thus we
65 * can best busy wait. This define gives the total amount of reads to try.
66 */
67#define ABIT_UGURU_WAIT_TIMEOUT 125
68/*
69 * However sometimes older versions of the uGuru seem to be distracted and they
70 * do not respond for a long time. To handle this we sleep before each of the
71 * last ABIT_UGURU_WAIT_TIMEOUT_SLEEP tries.
72 */
73#define ABIT_UGURU_WAIT_TIMEOUT_SLEEP 5
74/*
75 * Normally all expected status in abituguru_ready, are reported after the
76 * first read, but sometimes not and we need to poll.
77 */
78#define ABIT_UGURU_READY_TIMEOUT 5
79/* Maximum 3 retries on timedout reads/writes, delay 200 ms before retrying */
80#define ABIT_UGURU_MAX_RETRIES 3
81#define ABIT_UGURU_RETRY_DELAY (HZ/5)
82/* Maximum 2 timeouts in abituguru_update_device, iow 3 in a row is an error */
83#define ABIT_UGURU_MAX_TIMEOUTS 2
84/* utility macros */
85#define ABIT_UGURU_NAME "abituguru"
86#define ABIT_UGURU_DEBUG(level, format, arg...) \
87 do { \
88 if (level <= verbose) \
89 pr_debug(format , ## arg); \
90 } while (0)
91
92/* Macros to help calculate the sysfs_names array length */
93/*
94 * sum of strlen of: in??_input\0, in??_{min,max}\0, in??_{min,max}_alarm\0,
95 * in??_{min,max}_alarm_enable\0, in??_beep\0, in??_shutdown\0
96 */
97#define ABITUGURU_IN_NAMES_LENGTH (11 + 2 * 9 + 2 * 15 + 2 * 22 + 10 + 14)
98/*
99 * sum of strlen of: temp??_input\0, temp??_max\0, temp??_crit\0,
100 * temp??_alarm\0, temp??_alarm_enable\0, temp??_beep\0, temp??_shutdown\0
101 */
102#define ABITUGURU_TEMP_NAMES_LENGTH (13 + 11 + 12 + 13 + 20 + 12 + 16)
103/*
104 * sum of strlen of: fan?_input\0, fan?_min\0, fan?_alarm\0,
105 * fan?_alarm_enable\0, fan?_beep\0, fan?_shutdown\0
106 */
107#define ABITUGURU_FAN_NAMES_LENGTH (11 + 9 + 11 + 18 + 10 + 14)
108/*
109 * sum of strlen of: pwm?_enable\0, pwm?_auto_channels_temp\0,
110 * pwm?_auto_point{1,2}_pwm\0, pwm?_auto_point{1,2}_temp\0
111 */
112#define ABITUGURU_PWM_NAMES_LENGTH (12 + 24 + 2 * 21 + 2 * 22)
113/* IN_NAMES_LENGTH > TEMP_NAMES_LENGTH so assume all bank1 sensors are in */
114#define ABITUGURU_SYSFS_NAMES_LENGTH ( \
115 ABIT_UGURU_MAX_BANK1_SENSORS * ABITUGURU_IN_NAMES_LENGTH + \
116 ABIT_UGURU_MAX_BANK2_SENSORS * ABITUGURU_FAN_NAMES_LENGTH + \
117 ABIT_UGURU_MAX_PWMS * ABITUGURU_PWM_NAMES_LENGTH)
118
119/*
120 * All the macros below are named identical to the oguru and oguru2 programs
121 * reverse engineered by Olle Sandberg, hence the names might not be 100%
122 * logical. I could come up with better names, but I prefer keeping the names
123 * identical so that this driver can be compared with his work more easily.
124 */
125/* Two i/o-ports are used by uGuru */
126#define ABIT_UGURU_BASE 0x00E0
127/* Used to tell uGuru what to read and to read the actual data */
128#define ABIT_UGURU_CMD 0x00
129/* Mostly used to check if uGuru is busy */
130#define ABIT_UGURU_DATA 0x04
131#define ABIT_UGURU_REGION_LENGTH 5
132/* uGuru status' */
133#define ABIT_UGURU_STATUS_WRITE 0x00 /* Ready to be written */
134#define ABIT_UGURU_STATUS_READ 0x01 /* Ready to be read */
135#define ABIT_UGURU_STATUS_INPUT 0x08 /* More input */
136#define ABIT_UGURU_STATUS_READY 0x09 /* Ready to be written */
137
138/* Constants */
139/* in (Volt) sensors go up to 3494 mV, temp to 255000 millidegrees Celsius */
140static const int abituguru_bank1_max_value[2] = { 3494, 255000 };
141/*
142 * Min / Max allowed values for sensor2 (fan) alarm threshold, these values
143 * correspond to 300-3000 RPM
144 */
145static const u8 abituguru_bank2_min_threshold = 5;
146static const u8 abituguru_bank2_max_threshold = 50;
147/*
148 * Register 0 is a bitfield, 1 and 2 are pwm settings (255 = 100%), 3 and 4
149 * are temperature trip points.
150 */
151static const int abituguru_pwm_settings_multiplier[5] = { 0, 1, 1, 1000, 1000 };
152/*
153 * Min / Max allowed values for pwm_settings. Note: pwm1 (CPU fan) is a
154 * special case the minimum allowed pwm% setting for this is 30% (77) on
155 * some MB's this special case is handled in the code!
156 */
157static const u8 abituguru_pwm_min[5] = { 0, 170, 170, 25, 25 };
158static const u8 abituguru_pwm_max[5] = { 0, 255, 255, 75, 75 };
159
160
161/* Insmod parameters */
162static bool force;
163module_param(force, bool, 0);
164MODULE_PARM_DESC(force, "Set to one to force detection.");
165static int bank1_types[ABIT_UGURU_MAX_BANK1_SENSORS] = { -1, -1, -1, -1, -1,
166 -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 };
167module_param_array(bank1_types, int, NULL, 0);
168MODULE_PARM_DESC(bank1_types, "Bank1 sensortype autodetection override:\n"
169 " -1 autodetect\n"
170 " 0 volt sensor\n"
171 " 1 temp sensor\n"
172 " 2 not connected");
173static int fan_sensors;
174module_param(fan_sensors, int, 0);
175MODULE_PARM_DESC(fan_sensors, "Number of fan sensors on the uGuru "
176 "(0 = autodetect)");
177static int pwms;
178module_param(pwms, int, 0);
179MODULE_PARM_DESC(pwms, "Number of PWMs on the uGuru "
180 "(0 = autodetect)");
181
182/* Default verbose is 2, since this driver is still in the testing phase */
183static int verbose = 2;
184module_param(verbose, int, 0644);
185MODULE_PARM_DESC(verbose, "How verbose should the driver be? (0-3):\n"
186 " 0 normal output\n"
187 " 1 + verbose error reporting\n"
188 " 2 + sensors type probing info\n"
189 " 3 + retryable error reporting");
190
191
192/*
193 * For the Abit uGuru, we need to keep some data in memory.
194 * The structure is dynamically allocated, at the same time when a new
195 * abituguru device is allocated.
196 */
197struct abituguru_data {
198 struct device *hwmon_dev; /* hwmon registered device */
199 struct mutex update_lock; /* protect access to data and uGuru */
200 unsigned long last_updated; /* In jiffies */
201 unsigned short addr; /* uguru base address */
202 char uguru_ready; /* is the uguru in ready state? */
203 unsigned char update_timeouts; /*
204 * number of update timeouts since last
205 * successful update
206 */
207
208 /*
209 * The sysfs attr and their names are generated automatically, for bank1
210 * we cannot use a predefined array because we don't know beforehand
211 * of a sensor is a volt or a temp sensor, for bank2 and the pwms its
212 * easier todo things the same way. For in sensors we have 9 (temp 7)
213 * sysfs entries per sensor, for bank2 and pwms 6.
214 */
215 struct sensor_device_attribute_2 sysfs_attr[
216 ABIT_UGURU_MAX_BANK1_SENSORS * 9 +
217 ABIT_UGURU_MAX_BANK2_SENSORS * 6 + ABIT_UGURU_MAX_PWMS * 6];
218 /* Buffer to store the dynamically generated sysfs names */
219 char sysfs_names[ABITUGURU_SYSFS_NAMES_LENGTH];
220
221 /* Bank 1 data */
222 /* number of and addresses of [0] in, [1] temp sensors */
223 u8 bank1_sensors[2];
224 u8 bank1_address[2][ABIT_UGURU_MAX_BANK1_SENSORS];
225 u8 bank1_value[ABIT_UGURU_MAX_BANK1_SENSORS];
226 /*
227 * This array holds 3 entries per sensor for the bank 1 sensor settings
228 * (flags, min, max for voltage / flags, warn, shutdown for temp).
229 */
230 u8 bank1_settings[ABIT_UGURU_MAX_BANK1_SENSORS][3];
231 /*
232 * Maximum value for each sensor used for scaling in mV/millidegrees
233 * Celsius.
234 */
235 int bank1_max_value[ABIT_UGURU_MAX_BANK1_SENSORS];
236
237 /* Bank 2 data, ABIT_UGURU_MAX_BANK2_SENSORS entries for bank2 */
238 u8 bank2_sensors; /* actual number of bank2 sensors found */
239 u8 bank2_value[ABIT_UGURU_MAX_BANK2_SENSORS];
240 u8 bank2_settings[ABIT_UGURU_MAX_BANK2_SENSORS][2]; /* flags, min */
241
242 /* Alarms 2 bytes for bank1, 1 byte for bank2 */
243 u8 alarms[3];
244
245 /* Fan PWM (speed control) 5 bytes per PWM */
246 u8 pwms; /* actual number of pwms found */
247 u8 pwm_settings[ABIT_UGURU_MAX_PWMS][5];
248};
249
250static const char *never_happen = "This should never happen.";
251static const char *report_this =
252 "Please report this to the abituguru maintainer (see MAINTAINERS)";
253
254/* wait till the uguru is in the specified state */
255static int abituguru_wait(struct abituguru_data *data, u8 state)
256{
257 int timeout = ABIT_UGURU_WAIT_TIMEOUT;
258
259 while (inb_p(data->addr + ABIT_UGURU_DATA) != state) {
260 timeout--;
261 if (timeout == 0)
262 return -EBUSY;
263 /*
264 * sleep a bit before our last few tries, see the comment on
265 * this where ABIT_UGURU_WAIT_TIMEOUT_SLEEP is defined.
266 */
267 if (timeout <= ABIT_UGURU_WAIT_TIMEOUT_SLEEP)
268 msleep(0);
269 }
270 return 0;
271}
272
273/* Put the uguru in ready for input state */
274static int abituguru_ready(struct abituguru_data *data)
275{
276 int timeout = ABIT_UGURU_READY_TIMEOUT;
277
278 if (data->uguru_ready)
279 return 0;
280
281 /* Reset? / Prepare for next read/write cycle */
282 outb(0x00, data->addr + ABIT_UGURU_DATA);
283
284 /* Wait till the uguru is ready */
285 if (abituguru_wait(data, ABIT_UGURU_STATUS_READY)) {
286 ABIT_UGURU_DEBUG(1,
287 "timeout exceeded waiting for ready state\n");
288 return -EIO;
289 }
290
291 /* Cmd port MUST be read now and should contain 0xAC */
292 while (inb_p(data->addr + ABIT_UGURU_CMD) != 0xAC) {
293 timeout--;
294 if (timeout == 0) {
295 ABIT_UGURU_DEBUG(1,
296 "CMD reg does not hold 0xAC after ready command\n");
297 return -EIO;
298 }
299 msleep(0);
300 }
301
302 /*
303 * After this the ABIT_UGURU_DATA port should contain
304 * ABIT_UGURU_STATUS_INPUT
305 */
306 timeout = ABIT_UGURU_READY_TIMEOUT;
307 while (inb_p(data->addr + ABIT_UGURU_DATA) != ABIT_UGURU_STATUS_INPUT) {
308 timeout--;
309 if (timeout == 0) {
310 ABIT_UGURU_DEBUG(1,
311 "state != more input after ready command\n");
312 return -EIO;
313 }
314 msleep(0);
315 }
316
317 data->uguru_ready = 1;
318 return 0;
319}
320
321/*
322 * Send the bank and then sensor address to the uGuru for the next read/write
323 * cycle. This function gets called as the first part of a read/write by
324 * abituguru_read and abituguru_write. This function should never be
325 * called by any other function.
326 */
327static int abituguru_send_address(struct abituguru_data *data,
328 u8 bank_addr, u8 sensor_addr, int retries)
329{
330 /*
331 * assume the caller does error handling itself if it has not requested
332 * any retries, and thus be quiet.
333 */
334 int report_errors = retries;
335
336 for (;;) {
337 /*
338 * Make sure the uguru is ready and then send the bank address,
339 * after this the uguru is no longer "ready".
340 */
341 if (abituguru_ready(data) != 0)
342 return -EIO;
343 outb(bank_addr, data->addr + ABIT_UGURU_DATA);
344 data->uguru_ready = 0;
345
346 /*
347 * Wait till the uguru is ABIT_UGURU_STATUS_INPUT state again
348 * and send the sensor addr
349 */
350 if (abituguru_wait(data, ABIT_UGURU_STATUS_INPUT)) {
351 if (retries) {
352 ABIT_UGURU_DEBUG(3, "timeout exceeded "
353 "waiting for more input state, %d "
354 "tries remaining\n", retries);
355 set_current_state(TASK_UNINTERRUPTIBLE);
356 schedule_timeout(ABIT_UGURU_RETRY_DELAY);
357 retries--;
358 continue;
359 }
360 if (report_errors)
361 ABIT_UGURU_DEBUG(1, "timeout exceeded "
362 "waiting for more input state "
363 "(bank: %d)\n", (int)bank_addr);
364 return -EBUSY;
365 }
366 outb(sensor_addr, data->addr + ABIT_UGURU_CMD);
367 return 0;
368 }
369}
370
371/*
372 * Read count bytes from sensor sensor_addr in bank bank_addr and store the
373 * result in buf, retry the send address part of the read retries times.
374 */
375static int abituguru_read(struct abituguru_data *data,
376 u8 bank_addr, u8 sensor_addr, u8 *buf, int count, int retries)
377{
378 int i;
379
380 /* Send the address */
381 i = abituguru_send_address(data, bank_addr, sensor_addr, retries);
382 if (i)
383 return i;
384
385 /* And read the data */
386 for (i = 0; i < count; i++) {
387 if (abituguru_wait(data, ABIT_UGURU_STATUS_READ)) {
388 ABIT_UGURU_DEBUG(retries ? 1 : 3,
389 "timeout exceeded waiting for "
390 "read state (bank: %d, sensor: %d)\n",
391 (int)bank_addr, (int)sensor_addr);
392 break;
393 }
394 buf[i] = inb(data->addr + ABIT_UGURU_CMD);
395 }
396
397 /* Last put the chip back in ready state */
398 abituguru_ready(data);
399
400 return i;
401}
402
403/*
404 * Write count bytes from buf to sensor sensor_addr in bank bank_addr, the send
405 * address part of the write is always retried ABIT_UGURU_MAX_RETRIES times.
406 */
407static int abituguru_write(struct abituguru_data *data,
408 u8 bank_addr, u8 sensor_addr, u8 *buf, int count)
409{
410 /*
411 * We use the ready timeout as we have to wait for 0xAC just like the
412 * ready function
413 */
414 int i, timeout = ABIT_UGURU_READY_TIMEOUT;
415
416 /* Send the address */
417 i = abituguru_send_address(data, bank_addr, sensor_addr,
418 ABIT_UGURU_MAX_RETRIES);
419 if (i)
420 return i;
421
422 /* And write the data */
423 for (i = 0; i < count; i++) {
424 if (abituguru_wait(data, ABIT_UGURU_STATUS_WRITE)) {
425 ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for "
426 "write state (bank: %d, sensor: %d)\n",
427 (int)bank_addr, (int)sensor_addr);
428 break;
429 }
430 outb(buf[i], data->addr + ABIT_UGURU_CMD);
431 }
432
433 /*
434 * Now we need to wait till the chip is ready to be read again,
435 * so that we can read 0xAC as confirmation that our write has
436 * succeeded.
437 */
438 if (abituguru_wait(data, ABIT_UGURU_STATUS_READ)) {
439 ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for read state "
440 "after write (bank: %d, sensor: %d)\n", (int)bank_addr,
441 (int)sensor_addr);
442 return -EIO;
443 }
444
445 /* Cmd port MUST be read now and should contain 0xAC */
446 while (inb_p(data->addr + ABIT_UGURU_CMD) != 0xAC) {
447 timeout--;
448 if (timeout == 0) {
449 ABIT_UGURU_DEBUG(1, "CMD reg does not hold 0xAC after "
450 "write (bank: %d, sensor: %d)\n",
451 (int)bank_addr, (int)sensor_addr);
452 return -EIO;
453 }
454 msleep(0);
455 }
456
457 /* Last put the chip back in ready state */
458 abituguru_ready(data);
459
460 return i;
461}
462
463/*
464 * Detect sensor type. Temp and Volt sensors are enabled with
465 * different masks and will ignore enable masks not meant for them.
466 * This enables us to test what kind of sensor we're dealing with.
467 * By setting the alarm thresholds so that we will always get an
468 * alarm for sensor type X and then enabling the sensor as sensor type
469 * X, if we then get an alarm it is a sensor of type X.
470 */
471static int
472abituguru_detect_bank1_sensor_type(struct abituguru_data *data,
473 u8 sensor_addr)
474{
475 u8 val, test_flag, buf[3];
476 int i, ret = -ENODEV; /* error is the most common used retval :| */
477
478 /* If overriden by the user return the user selected type */
479 if (bank1_types[sensor_addr] >= ABIT_UGURU_IN_SENSOR &&
480 bank1_types[sensor_addr] <= ABIT_UGURU_NC) {
481 ABIT_UGURU_DEBUG(2, "assuming sensor type %d for bank1 sensor "
482 "%d because of \"bank1_types\" module param\n",
483 bank1_types[sensor_addr], (int)sensor_addr);
484 return bank1_types[sensor_addr];
485 }
486
487 /* First read the sensor and the current settings */
488 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1, sensor_addr, &val,
489 1, ABIT_UGURU_MAX_RETRIES) != 1)
490 return -ENODEV;
491
492 /* Test val is sane / usable for sensor type detection. */
493 if ((val < 10u) || (val > 250u)) {
494 pr_warn("bank1-sensor: %d reading (%d) too close to limits, "
495 "unable to determine sensor type, skipping sensor\n",
496 (int)sensor_addr, (int)val);
497 /*
498 * assume no sensor is there for sensors for which we can't
499 * determine the sensor type because their reading is too close
500 * to their limits, this usually means no sensor is there.
501 */
502 return ABIT_UGURU_NC;
503 }
504
505 ABIT_UGURU_DEBUG(2, "testing bank1 sensor %d\n", (int)sensor_addr);
506 /*
507 * Volt sensor test, enable volt low alarm, set min value ridiculously
508 * high, or vica versa if the reading is very high. If its a volt
509 * sensor this should always give us an alarm.
510 */
511 if (val <= 240u) {
512 buf[0] = ABIT_UGURU_VOLT_LOW_ALARM_ENABLE;
513 buf[1] = 245;
514 buf[2] = 250;
515 test_flag = ABIT_UGURU_VOLT_LOW_ALARM_FLAG;
516 } else {
517 buf[0] = ABIT_UGURU_VOLT_HIGH_ALARM_ENABLE;
518 buf[1] = 5;
519 buf[2] = 10;
520 test_flag = ABIT_UGURU_VOLT_HIGH_ALARM_FLAG;
521 }
522
523 if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
524 buf, 3) != 3)
525 goto abituguru_detect_bank1_sensor_type_exit;
526 /*
527 * Now we need 20 ms to give the uguru time to read the sensors
528 * and raise a voltage alarm
529 */
530 set_current_state(TASK_UNINTERRUPTIBLE);
531 schedule_timeout(HZ/50);
532 /* Check for alarm and check the alarm is a volt low alarm. */
533 if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0, buf, 3,
534 ABIT_UGURU_MAX_RETRIES) != 3)
535 goto abituguru_detect_bank1_sensor_type_exit;
536 if (buf[sensor_addr/8] & (0x01 << (sensor_addr % 8))) {
537 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1,
538 sensor_addr, buf, 3,
539 ABIT_UGURU_MAX_RETRIES) != 3)
540 goto abituguru_detect_bank1_sensor_type_exit;
541 if (buf[0] & test_flag) {
542 ABIT_UGURU_DEBUG(2, " found volt sensor\n");
543 ret = ABIT_UGURU_IN_SENSOR;
544 goto abituguru_detect_bank1_sensor_type_exit;
545 } else
546 ABIT_UGURU_DEBUG(2, " alarm raised during volt "
547 "sensor test, but volt range flag not set\n");
548 } else
549 ABIT_UGURU_DEBUG(2, " alarm not raised during volt sensor "
550 "test\n");
551
552 /*
553 * Temp sensor test, enable sensor as a temp sensor, set beep value
554 * ridiculously low (but not too low, otherwise uguru ignores it).
555 * If its a temp sensor this should always give us an alarm.
556 */
557 buf[0] = ABIT_UGURU_TEMP_HIGH_ALARM_ENABLE;
558 buf[1] = 5;
559 buf[2] = 10;
560 if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
561 buf, 3) != 3)
562 goto abituguru_detect_bank1_sensor_type_exit;
563 /*
564 * Now we need 50 ms to give the uguru time to read the sensors
565 * and raise a temp alarm
566 */
567 set_current_state(TASK_UNINTERRUPTIBLE);
568 schedule_timeout(HZ/20);
569 /* Check for alarm and check the alarm is a temp high alarm. */
570 if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0, buf, 3,
571 ABIT_UGURU_MAX_RETRIES) != 3)
572 goto abituguru_detect_bank1_sensor_type_exit;
573 if (buf[sensor_addr/8] & (0x01 << (sensor_addr % 8))) {
574 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1,
575 sensor_addr, buf, 3,
576 ABIT_UGURU_MAX_RETRIES) != 3)
577 goto abituguru_detect_bank1_sensor_type_exit;
578 if (buf[0] & ABIT_UGURU_TEMP_HIGH_ALARM_FLAG) {
579 ABIT_UGURU_DEBUG(2, " found temp sensor\n");
580 ret = ABIT_UGURU_TEMP_SENSOR;
581 goto abituguru_detect_bank1_sensor_type_exit;
582 } else
583 ABIT_UGURU_DEBUG(2, " alarm raised during temp "
584 "sensor test, but temp high flag not set\n");
585 } else
586 ABIT_UGURU_DEBUG(2, " alarm not raised during temp sensor "
587 "test\n");
588
589 ret = ABIT_UGURU_NC;
590abituguru_detect_bank1_sensor_type_exit:
591 /*
592 * Restore original settings, failing here is really BAD, it has been
593 * reported that some BIOS-es hang when entering the uGuru menu with
594 * invalid settings present in the uGuru, so we try this 3 times.
595 */
596 for (i = 0; i < 3; i++)
597 if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2,
598 sensor_addr, data->bank1_settings[sensor_addr],
599 3) == 3)
600 break;
601 if (i == 3) {
602 pr_err("Fatal error could not restore original settings. %s %s\n",
603 never_happen, report_this);
604 return -ENODEV;
605 }
606 return ret;
607}
608
609/*
610 * These functions try to find out how many sensors there are in bank2 and how
611 * many pwms there are. The purpose of this is to make sure that we don't give
612 * the user the possibility to change settings for non-existent sensors / pwm.
613 * The uGuru will happily read / write whatever memory happens to be after the
614 * memory storing the PWM settings when reading/writing to a PWM which is not
615 * there. Notice even if we detect a PWM which doesn't exist we normally won't
616 * write to it, unless the user tries to change the settings.
617 *
618 * Although the uGuru allows reading (settings) from non existing bank2
619 * sensors, my version of the uGuru does seem to stop writing to them, the
620 * write function above aborts in this case with:
621 * "CMD reg does not hold 0xAC after write"
622 *
623 * Notice these 2 tests are non destructive iow read-only tests, otherwise
624 * they would defeat their purpose. Although for the bank2_sensors detection a
625 * read/write test would be feasible because of the reaction above, I've
626 * however opted to stay on the safe side.
627 */
628static void
629abituguru_detect_no_bank2_sensors(struct abituguru_data *data)
630{
631 int i;
632
633 if (fan_sensors > 0 && fan_sensors <= ABIT_UGURU_MAX_BANK2_SENSORS) {
634 data->bank2_sensors = fan_sensors;
635 ABIT_UGURU_DEBUG(2, "assuming %d fan sensors because of "
636 "\"fan_sensors\" module param\n",
637 (int)data->bank2_sensors);
638 return;
639 }
640
641 ABIT_UGURU_DEBUG(2, "detecting number of fan sensors\n");
642 for (i = 0; i < ABIT_UGURU_MAX_BANK2_SENSORS; i++) {
643 /*
644 * 0x89 are the known used bits:
645 * -0x80 enable shutdown
646 * -0x08 enable beep
647 * -0x01 enable alarm
648 * All other bits should be 0, but on some motherboards
649 * 0x40 (bit 6) is also high for some of the fans??
650 */
651 if (data->bank2_settings[i][0] & ~0xC9) {
652 ABIT_UGURU_DEBUG(2, " bank2 sensor %d does not seem "
653 "to be a fan sensor: settings[0] = %02X\n",
654 i, (unsigned int)data->bank2_settings[i][0]);
655 break;
656 }
657
658 /* check if the threshold is within the allowed range */
659 if (data->bank2_settings[i][1] <
660 abituguru_bank2_min_threshold) {
661 ABIT_UGURU_DEBUG(2, " bank2 sensor %d does not seem "
662 "to be a fan sensor: the threshold (%d) is "
663 "below the minimum (%d)\n", i,
664 (int)data->bank2_settings[i][1],
665 (int)abituguru_bank2_min_threshold);
666 break;
667 }
668 if (data->bank2_settings[i][1] >
669 abituguru_bank2_max_threshold) {
670 ABIT_UGURU_DEBUG(2, " bank2 sensor %d does not seem "
671 "to be a fan sensor: the threshold (%d) is "
672 "above the maximum (%d)\n", i,
673 (int)data->bank2_settings[i][1],
674 (int)abituguru_bank2_max_threshold);
675 break;
676 }
677 }
678
679 data->bank2_sensors = i;
680 ABIT_UGURU_DEBUG(2, " found: %d fan sensors\n",
681 (int)data->bank2_sensors);
682}
683
684static void
685abituguru_detect_no_pwms(struct abituguru_data *data)
686{
687 int i, j;
688
689 if (pwms > 0 && pwms <= ABIT_UGURU_MAX_PWMS) {
690 data->pwms = pwms;
691 ABIT_UGURU_DEBUG(2, "assuming %d PWM outputs because of "
692 "\"pwms\" module param\n", (int)data->pwms);
693 return;
694 }
695
696 ABIT_UGURU_DEBUG(2, "detecting number of PWM outputs\n");
697 for (i = 0; i < ABIT_UGURU_MAX_PWMS; i++) {
698 /*
699 * 0x80 is the enable bit and the low
700 * nibble is which temp sensor to use,
701 * the other bits should be 0
702 */
703 if (data->pwm_settings[i][0] & ~0x8F) {
704 ABIT_UGURU_DEBUG(2, " pwm channel %d does not seem "
705 "to be a pwm channel: settings[0] = %02X\n",
706 i, (unsigned int)data->pwm_settings[i][0]);
707 break;
708 }
709
710 /*
711 * the low nibble must correspond to one of the temp sensors
712 * we've found
713 */
714 for (j = 0; j < data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR];
715 j++) {
716 if (data->bank1_address[ABIT_UGURU_TEMP_SENSOR][j] ==
717 (data->pwm_settings[i][0] & 0x0F))
718 break;
719 }
720 if (j == data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR]) {
721 ABIT_UGURU_DEBUG(2, " pwm channel %d does not seem "
722 "to be a pwm channel: %d is not a valid temp "
723 "sensor address\n", i,
724 data->pwm_settings[i][0] & 0x0F);
725 break;
726 }
727
728 /* check if all other settings are within the allowed range */
729 for (j = 1; j < 5; j++) {
730 u8 min;
731 /* special case pwm1 min pwm% */
732 if ((i == 0) && ((j == 1) || (j == 2)))
733 min = 77;
734 else
735 min = abituguru_pwm_min[j];
736 if (data->pwm_settings[i][j] < min) {
737 ABIT_UGURU_DEBUG(2, " pwm channel %d does "
738 "not seem to be a pwm channel: "
739 "setting %d (%d) is below the minimum "
740 "value (%d)\n", i, j,
741 (int)data->pwm_settings[i][j],
742 (int)min);
743 goto abituguru_detect_no_pwms_exit;
744 }
745 if (data->pwm_settings[i][j] > abituguru_pwm_max[j]) {
746 ABIT_UGURU_DEBUG(2, " pwm channel %d does "
747 "not seem to be a pwm channel: "
748 "setting %d (%d) is above the maximum "
749 "value (%d)\n", i, j,
750 (int)data->pwm_settings[i][j],
751 (int)abituguru_pwm_max[j]);
752 goto abituguru_detect_no_pwms_exit;
753 }
754 }
755
756 /* check that min temp < max temp and min pwm < max pwm */
757 if (data->pwm_settings[i][1] >= data->pwm_settings[i][2]) {
758 ABIT_UGURU_DEBUG(2, " pwm channel %d does not seem "
759 "to be a pwm channel: min pwm (%d) >= "
760 "max pwm (%d)\n", i,
761 (int)data->pwm_settings[i][1],
762 (int)data->pwm_settings[i][2]);
763 break;
764 }
765 if (data->pwm_settings[i][3] >= data->pwm_settings[i][4]) {
766 ABIT_UGURU_DEBUG(2, " pwm channel %d does not seem "
767 "to be a pwm channel: min temp (%d) >= "
768 "max temp (%d)\n", i,
769 (int)data->pwm_settings[i][3],
770 (int)data->pwm_settings[i][4]);
771 break;
772 }
773 }
774
775abituguru_detect_no_pwms_exit:
776 data->pwms = i;
777 ABIT_UGURU_DEBUG(2, " found: %d PWM outputs\n", (int)data->pwms);
778}
779
780/*
781 * Following are the sysfs callback functions. These functions expect:
782 * sensor_device_attribute_2->index: sensor address/offset in the bank
783 * sensor_device_attribute_2->nr: register offset, bitmask or NA.
784 */
785static struct abituguru_data *abituguru_update_device(struct device *dev);
786
787static ssize_t show_bank1_value(struct device *dev,
788 struct device_attribute *devattr, char *buf)
789{
790 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
791 struct abituguru_data *data = abituguru_update_device(dev);
792 if (!data)
793 return -EIO;
794 return sprintf(buf, "%d\n", (data->bank1_value[attr->index] *
795 data->bank1_max_value[attr->index] + 128) / 255);
796}
797
798static ssize_t show_bank1_setting(struct device *dev,
799 struct device_attribute *devattr, char *buf)
800{
801 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
802 struct abituguru_data *data = dev_get_drvdata(dev);
803 return sprintf(buf, "%d\n",
804 (data->bank1_settings[attr->index][attr->nr] *
805 data->bank1_max_value[attr->index] + 128) / 255);
806}
807
808static ssize_t show_bank2_value(struct device *dev,
809 struct device_attribute *devattr, char *buf)
810{
811 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
812 struct abituguru_data *data = abituguru_update_device(dev);
813 if (!data)
814 return -EIO;
815 return sprintf(buf, "%d\n", (data->bank2_value[attr->index] *
816 ABIT_UGURU_FAN_MAX + 128) / 255);
817}
818
819static ssize_t show_bank2_setting(struct device *dev,
820 struct device_attribute *devattr, char *buf)
821{
822 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
823 struct abituguru_data *data = dev_get_drvdata(dev);
824 return sprintf(buf, "%d\n",
825 (data->bank2_settings[attr->index][attr->nr] *
826 ABIT_UGURU_FAN_MAX + 128) / 255);
827}
828
829static ssize_t store_bank1_setting(struct device *dev, struct device_attribute
830 *devattr, const char *buf, size_t count)
831{
832 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
833 struct abituguru_data *data = dev_get_drvdata(dev);
834 unsigned long val;
835 ssize_t ret;
836
837 ret = kstrtoul(buf, 10, &val);
838 if (ret)
839 return ret;
840
841 ret = count;
842 val = (val * 255 + data->bank1_max_value[attr->index] / 2) /
843 data->bank1_max_value[attr->index];
844 if (val > 255)
845 return -EINVAL;
846
847 mutex_lock(&data->update_lock);
848 if (data->bank1_settings[attr->index][attr->nr] != val) {
849 u8 orig_val = data->bank1_settings[attr->index][attr->nr];
850 data->bank1_settings[attr->index][attr->nr] = val;
851 if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2,
852 attr->index, data->bank1_settings[attr->index],
853 3) <= attr->nr) {
854 data->bank1_settings[attr->index][attr->nr] = orig_val;
855 ret = -EIO;
856 }
857 }
858 mutex_unlock(&data->update_lock);
859 return ret;
860}
861
862static ssize_t store_bank2_setting(struct device *dev, struct device_attribute
863 *devattr, const char *buf, size_t count)
864{
865 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
866 struct abituguru_data *data = dev_get_drvdata(dev);
867 unsigned long val;
868 ssize_t ret;
869
870 ret = kstrtoul(buf, 10, &val);
871 if (ret)
872 return ret;
873
874 ret = count;
875 val = (val * 255 + ABIT_UGURU_FAN_MAX / 2) / ABIT_UGURU_FAN_MAX;
876
877 /* this check can be done before taking the lock */
878 if (val < abituguru_bank2_min_threshold ||
879 val > abituguru_bank2_max_threshold)
880 return -EINVAL;
881
882 mutex_lock(&data->update_lock);
883 if (data->bank2_settings[attr->index][attr->nr] != val) {
884 u8 orig_val = data->bank2_settings[attr->index][attr->nr];
885 data->bank2_settings[attr->index][attr->nr] = val;
886 if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK2 + 2,
887 attr->index, data->bank2_settings[attr->index],
888 2) <= attr->nr) {
889 data->bank2_settings[attr->index][attr->nr] = orig_val;
890 ret = -EIO;
891 }
892 }
893 mutex_unlock(&data->update_lock);
894 return ret;
895}
896
897static ssize_t show_bank1_alarm(struct device *dev,
898 struct device_attribute *devattr, char *buf)
899{
900 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
901 struct abituguru_data *data = abituguru_update_device(dev);
902 if (!data)
903 return -EIO;
904 /*
905 * See if the alarm bit for this sensor is set, and if the
906 * alarm matches the type of alarm we're looking for (for volt
907 * it can be either low or high). The type is stored in a few
908 * readonly bits in the settings part of the relevant sensor.
909 * The bitmask of the type is passed to us in attr->nr.
910 */
911 if ((data->alarms[attr->index / 8] & (0x01 << (attr->index % 8))) &&
912 (data->bank1_settings[attr->index][0] & attr->nr))
913 return sprintf(buf, "1\n");
914 else
915 return sprintf(buf, "0\n");
916}
917
918static ssize_t show_bank2_alarm(struct device *dev,
919 struct device_attribute *devattr, char *buf)
920{
921 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
922 struct abituguru_data *data = abituguru_update_device(dev);
923 if (!data)
924 return -EIO;
925 if (data->alarms[2] & (0x01 << attr->index))
926 return sprintf(buf, "1\n");
927 else
928 return sprintf(buf, "0\n");
929}
930
931static ssize_t show_bank1_mask(struct device *dev,
932 struct device_attribute *devattr, char *buf)
933{
934 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
935 struct abituguru_data *data = dev_get_drvdata(dev);
936 if (data->bank1_settings[attr->index][0] & attr->nr)
937 return sprintf(buf, "1\n");
938 else
939 return sprintf(buf, "0\n");
940}
941
942static ssize_t show_bank2_mask(struct device *dev,
943 struct device_attribute *devattr, char *buf)
944{
945 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
946 struct abituguru_data *data = dev_get_drvdata(dev);
947 if (data->bank2_settings[attr->index][0] & attr->nr)
948 return sprintf(buf, "1\n");
949 else
950 return sprintf(buf, "0\n");
951}
952
953static ssize_t store_bank1_mask(struct device *dev,
954 struct device_attribute *devattr, const char *buf, size_t count)
955{
956 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
957 struct abituguru_data *data = dev_get_drvdata(dev);
958 ssize_t ret;
959 u8 orig_val;
960 unsigned long mask;
961
962 ret = kstrtoul(buf, 10, &mask);
963 if (ret)
964 return ret;
965
966 ret = count;
967 mutex_lock(&data->update_lock);
968 orig_val = data->bank1_settings[attr->index][0];
969
970 if (mask)
971 data->bank1_settings[attr->index][0] |= attr->nr;
972 else
973 data->bank1_settings[attr->index][0] &= ~attr->nr;
974
975 if ((data->bank1_settings[attr->index][0] != orig_val) &&
976 (abituguru_write(data,
977 ABIT_UGURU_SENSOR_BANK1 + 2, attr->index,
978 data->bank1_settings[attr->index], 3) < 1)) {
979 data->bank1_settings[attr->index][0] = orig_val;
980 ret = -EIO;
981 }
982 mutex_unlock(&data->update_lock);
983 return ret;
984}
985
986static ssize_t store_bank2_mask(struct device *dev,
987 struct device_attribute *devattr, const char *buf, size_t count)
988{
989 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
990 struct abituguru_data *data = dev_get_drvdata(dev);
991 ssize_t ret;
992 u8 orig_val;
993 unsigned long mask;
994
995 ret = kstrtoul(buf, 10, &mask);
996 if (ret)
997 return ret;
998
999 ret = count;
1000 mutex_lock(&data->update_lock);
1001 orig_val = data->bank2_settings[attr->index][0];
1002
1003 if (mask)
1004 data->bank2_settings[attr->index][0] |= attr->nr;
1005 else
1006 data->bank2_settings[attr->index][0] &= ~attr->nr;
1007
1008 if ((data->bank2_settings[attr->index][0] != orig_val) &&
1009 (abituguru_write(data,
1010 ABIT_UGURU_SENSOR_BANK2 + 2, attr->index,
1011 data->bank2_settings[attr->index], 2) < 1)) {
1012 data->bank2_settings[attr->index][0] = orig_val;
1013 ret = -EIO;
1014 }
1015 mutex_unlock(&data->update_lock);
1016 return ret;
1017}
1018
1019/* Fan PWM (speed control) */
1020static ssize_t show_pwm_setting(struct device *dev,
1021 struct device_attribute *devattr, char *buf)
1022{
1023 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
1024 struct abituguru_data *data = dev_get_drvdata(dev);
1025 return sprintf(buf, "%d\n", data->pwm_settings[attr->index][attr->nr] *
1026 abituguru_pwm_settings_multiplier[attr->nr]);
1027}
1028
1029static ssize_t store_pwm_setting(struct device *dev, struct device_attribute
1030 *devattr, const char *buf, size_t count)
1031{
1032 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
1033 struct abituguru_data *data = dev_get_drvdata(dev);
1034 u8 min;
1035 unsigned long val;
1036 ssize_t ret;
1037
1038 ret = kstrtoul(buf, 10, &val);
1039 if (ret)
1040 return ret;
1041
1042 ret = count;
1043 val = (val + abituguru_pwm_settings_multiplier[attr->nr] / 2) /
1044 abituguru_pwm_settings_multiplier[attr->nr];
1045
1046 /* special case pwm1 min pwm% */
1047 if ((attr->index == 0) && ((attr->nr == 1) || (attr->nr == 2)))
1048 min = 77;
1049 else
1050 min = abituguru_pwm_min[attr->nr];
1051
1052 /* this check can be done before taking the lock */
1053 if (val < min || val > abituguru_pwm_max[attr->nr])
1054 return -EINVAL;
1055
1056 mutex_lock(&data->update_lock);
1057 /* this check needs to be done after taking the lock */
1058 if ((attr->nr & 1) &&
1059 (val >= data->pwm_settings[attr->index][attr->nr + 1]))
1060 ret = -EINVAL;
1061 else if (!(attr->nr & 1) &&
1062 (val <= data->pwm_settings[attr->index][attr->nr - 1]))
1063 ret = -EINVAL;
1064 else if (data->pwm_settings[attr->index][attr->nr] != val) {
1065 u8 orig_val = data->pwm_settings[attr->index][attr->nr];
1066 data->pwm_settings[attr->index][attr->nr] = val;
1067 if (abituguru_write(data, ABIT_UGURU_FAN_PWM + 1,
1068 attr->index, data->pwm_settings[attr->index],
1069 5) <= attr->nr) {
1070 data->pwm_settings[attr->index][attr->nr] =
1071 orig_val;
1072 ret = -EIO;
1073 }
1074 }
1075 mutex_unlock(&data->update_lock);
1076 return ret;
1077}
1078
1079static ssize_t show_pwm_sensor(struct device *dev,
1080 struct device_attribute *devattr, char *buf)
1081{
1082 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
1083 struct abituguru_data *data = dev_get_drvdata(dev);
1084 int i;
1085 /*
1086 * We need to walk to the temp sensor addresses to find what
1087 * the userspace id of the configured temp sensor is.
1088 */
1089 for (i = 0; i < data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR]; i++)
1090 if (data->bank1_address[ABIT_UGURU_TEMP_SENSOR][i] ==
1091 (data->pwm_settings[attr->index][0] & 0x0F))
1092 return sprintf(buf, "%d\n", i+1);
1093
1094 return -ENXIO;
1095}
1096
1097static ssize_t store_pwm_sensor(struct device *dev, struct device_attribute
1098 *devattr, const char *buf, size_t count)
1099{
1100 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
1101 struct abituguru_data *data = dev_get_drvdata(dev);
1102 ssize_t ret;
1103 unsigned long val;
1104 u8 orig_val;
1105 u8 address;
1106
1107 ret = kstrtoul(buf, 10, &val);
1108 if (ret)
1109 return ret;
1110
1111 if (val == 0 || val > data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR])
1112 return -EINVAL;
1113
1114 val -= 1;
1115 ret = count;
1116 mutex_lock(&data->update_lock);
1117 orig_val = data->pwm_settings[attr->index][0];
1118 address = data->bank1_address[ABIT_UGURU_TEMP_SENSOR][val];
1119 data->pwm_settings[attr->index][0] &= 0xF0;
1120 data->pwm_settings[attr->index][0] |= address;
1121 if (data->pwm_settings[attr->index][0] != orig_val) {
1122 if (abituguru_write(data, ABIT_UGURU_FAN_PWM + 1, attr->index,
1123 data->pwm_settings[attr->index], 5) < 1) {
1124 data->pwm_settings[attr->index][0] = orig_val;
1125 ret = -EIO;
1126 }
1127 }
1128 mutex_unlock(&data->update_lock);
1129 return ret;
1130}
1131
1132static ssize_t show_pwm_enable(struct device *dev,
1133 struct device_attribute *devattr, char *buf)
1134{
1135 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
1136 struct abituguru_data *data = dev_get_drvdata(dev);
1137 int res = 0;
1138 if (data->pwm_settings[attr->index][0] & ABIT_UGURU_FAN_PWM_ENABLE)
1139 res = 2;
1140 return sprintf(buf, "%d\n", res);
1141}
1142
1143static ssize_t store_pwm_enable(struct device *dev, struct device_attribute
1144 *devattr, const char *buf, size_t count)
1145{
1146 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
1147 struct abituguru_data *data = dev_get_drvdata(dev);
1148 u8 orig_val;
1149 ssize_t ret;
1150 unsigned long user_val;
1151
1152 ret = kstrtoul(buf, 10, &user_val);
1153 if (ret)
1154 return ret;
1155
1156 ret = count;
1157 mutex_lock(&data->update_lock);
1158 orig_val = data->pwm_settings[attr->index][0];
1159 switch (user_val) {
1160 case 0:
1161 data->pwm_settings[attr->index][0] &=
1162 ~ABIT_UGURU_FAN_PWM_ENABLE;
1163 break;
1164 case 2:
1165 data->pwm_settings[attr->index][0] |= ABIT_UGURU_FAN_PWM_ENABLE;
1166 break;
1167 default:
1168 ret = -EINVAL;
1169 }
1170 if ((data->pwm_settings[attr->index][0] != orig_val) &&
1171 (abituguru_write(data, ABIT_UGURU_FAN_PWM + 1,
1172 attr->index, data->pwm_settings[attr->index],
1173 5) < 1)) {
1174 data->pwm_settings[attr->index][0] = orig_val;
1175 ret = -EIO;
1176 }
1177 mutex_unlock(&data->update_lock);
1178 return ret;
1179}
1180
1181static ssize_t show_name(struct device *dev,
1182 struct device_attribute *devattr, char *buf)
1183{
1184 return sprintf(buf, "%s\n", ABIT_UGURU_NAME);
1185}
1186
1187/* Sysfs attr templates, the real entries are generated automatically. */
1188static const
1189struct sensor_device_attribute_2 abituguru_sysfs_bank1_templ[2][9] = {
1190 {
1191 SENSOR_ATTR_2(in%d_input, 0444, show_bank1_value, NULL, 0, 0),
1192 SENSOR_ATTR_2(in%d_min, 0644, show_bank1_setting,
1193 store_bank1_setting, 1, 0),
1194 SENSOR_ATTR_2(in%d_min_alarm, 0444, show_bank1_alarm, NULL,
1195 ABIT_UGURU_VOLT_LOW_ALARM_FLAG, 0),
1196 SENSOR_ATTR_2(in%d_max, 0644, show_bank1_setting,
1197 store_bank1_setting, 2, 0),
1198 SENSOR_ATTR_2(in%d_max_alarm, 0444, show_bank1_alarm, NULL,
1199 ABIT_UGURU_VOLT_HIGH_ALARM_FLAG, 0),
1200 SENSOR_ATTR_2(in%d_beep, 0644, show_bank1_mask,
1201 store_bank1_mask, ABIT_UGURU_BEEP_ENABLE, 0),
1202 SENSOR_ATTR_2(in%d_shutdown, 0644, show_bank1_mask,
1203 store_bank1_mask, ABIT_UGURU_SHUTDOWN_ENABLE, 0),
1204 SENSOR_ATTR_2(in%d_min_alarm_enable, 0644, show_bank1_mask,
1205 store_bank1_mask, ABIT_UGURU_VOLT_LOW_ALARM_ENABLE, 0),
1206 SENSOR_ATTR_2(in%d_max_alarm_enable, 0644, show_bank1_mask,
1207 store_bank1_mask, ABIT_UGURU_VOLT_HIGH_ALARM_ENABLE, 0),
1208 }, {
1209 SENSOR_ATTR_2(temp%d_input, 0444, show_bank1_value, NULL, 0, 0),
1210 SENSOR_ATTR_2(temp%d_alarm, 0444, show_bank1_alarm, NULL,
1211 ABIT_UGURU_TEMP_HIGH_ALARM_FLAG, 0),
1212 SENSOR_ATTR_2(temp%d_max, 0644, show_bank1_setting,
1213 store_bank1_setting, 1, 0),
1214 SENSOR_ATTR_2(temp%d_crit, 0644, show_bank1_setting,
1215 store_bank1_setting, 2, 0),
1216 SENSOR_ATTR_2(temp%d_beep, 0644, show_bank1_mask,
1217 store_bank1_mask, ABIT_UGURU_BEEP_ENABLE, 0),
1218 SENSOR_ATTR_2(temp%d_shutdown, 0644, show_bank1_mask,
1219 store_bank1_mask, ABIT_UGURU_SHUTDOWN_ENABLE, 0),
1220 SENSOR_ATTR_2(temp%d_alarm_enable, 0644, show_bank1_mask,
1221 store_bank1_mask, ABIT_UGURU_TEMP_HIGH_ALARM_ENABLE, 0),
1222 }
1223};
1224
1225static const struct sensor_device_attribute_2 abituguru_sysfs_fan_templ[6] = {
1226 SENSOR_ATTR_2(fan%d_input, 0444, show_bank2_value, NULL, 0, 0),
1227 SENSOR_ATTR_2(fan%d_alarm, 0444, show_bank2_alarm, NULL, 0, 0),
1228 SENSOR_ATTR_2(fan%d_min, 0644, show_bank2_setting,
1229 store_bank2_setting, 1, 0),
1230 SENSOR_ATTR_2(fan%d_beep, 0644, show_bank2_mask,
1231 store_bank2_mask, ABIT_UGURU_BEEP_ENABLE, 0),
1232 SENSOR_ATTR_2(fan%d_shutdown, 0644, show_bank2_mask,
1233 store_bank2_mask, ABIT_UGURU_SHUTDOWN_ENABLE, 0),
1234 SENSOR_ATTR_2(fan%d_alarm_enable, 0644, show_bank2_mask,
1235 store_bank2_mask, ABIT_UGURU_FAN_LOW_ALARM_ENABLE, 0),
1236};
1237
1238static const struct sensor_device_attribute_2 abituguru_sysfs_pwm_templ[6] = {
1239 SENSOR_ATTR_2(pwm%d_enable, 0644, show_pwm_enable,
1240 store_pwm_enable, 0, 0),
1241 SENSOR_ATTR_2(pwm%d_auto_channels_temp, 0644, show_pwm_sensor,
1242 store_pwm_sensor, 0, 0),
1243 SENSOR_ATTR_2(pwm%d_auto_point1_pwm, 0644, show_pwm_setting,
1244 store_pwm_setting, 1, 0),
1245 SENSOR_ATTR_2(pwm%d_auto_point2_pwm, 0644, show_pwm_setting,
1246 store_pwm_setting, 2, 0),
1247 SENSOR_ATTR_2(pwm%d_auto_point1_temp, 0644, show_pwm_setting,
1248 store_pwm_setting, 3, 0),
1249 SENSOR_ATTR_2(pwm%d_auto_point2_temp, 0644, show_pwm_setting,
1250 store_pwm_setting, 4, 0),
1251};
1252
1253static struct sensor_device_attribute_2 abituguru_sysfs_attr[] = {
1254 SENSOR_ATTR_2(name, 0444, show_name, NULL, 0, 0),
1255};
1256
1257static int abituguru_probe(struct platform_device *pdev)
1258{
1259 struct abituguru_data *data;
1260 int i, j, used, sysfs_names_free, sysfs_attr_i, res = -ENODEV;
1261 char *sysfs_filename;
1262
1263 /*
1264 * El weirdo probe order, to keep the sysfs order identical to the
1265 * BIOS and window-appliction listing order.
1266 */
1267 static const u8 probe_order[ABIT_UGURU_MAX_BANK1_SENSORS] = {
1268 0x00, 0x01, 0x03, 0x04, 0x0A, 0x08, 0x0E, 0x02,
1269 0x09, 0x06, 0x05, 0x0B, 0x0F, 0x0D, 0x07, 0x0C };
1270
1271 data = devm_kzalloc(&pdev->dev, sizeof(struct abituguru_data),
1272 GFP_KERNEL);
1273 if (!data)
1274 return -ENOMEM;
1275
1276 data->addr = platform_get_resource(pdev, IORESOURCE_IO, 0)->start;
1277 mutex_init(&data->update_lock);
1278 platform_set_drvdata(pdev, data);
1279
1280 /* See if the uGuru is ready */
1281 if (inb_p(data->addr + ABIT_UGURU_DATA) == ABIT_UGURU_STATUS_INPUT)
1282 data->uguru_ready = 1;
1283
1284 /*
1285 * Completely read the uGuru this has 2 purposes:
1286 * - testread / see if one really is there.
1287 * - make an in memory copy of all the uguru settings for future use.
1288 */
1289 if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0,
1290 data->alarms, 3, ABIT_UGURU_MAX_RETRIES) != 3)
1291 goto abituguru_probe_error;
1292
1293 for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
1294 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1, i,
1295 &data->bank1_value[i], 1,
1296 ABIT_UGURU_MAX_RETRIES) != 1)
1297 goto abituguru_probe_error;
1298 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1+1, i,
1299 data->bank1_settings[i], 3,
1300 ABIT_UGURU_MAX_RETRIES) != 3)
1301 goto abituguru_probe_error;
1302 }
1303 /*
1304 * Note: We don't know how many bank2 sensors / pwms there really are,
1305 * but in order to "detect" this we need to read the maximum amount
1306 * anyways. If we read sensors/pwms not there we'll just read crap
1307 * this can't hurt. We need the detection because we don't want
1308 * unwanted writes, which will hurt!
1309 */
1310 for (i = 0; i < ABIT_UGURU_MAX_BANK2_SENSORS; i++) {
1311 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK2, i,
1312 &data->bank2_value[i], 1,
1313 ABIT_UGURU_MAX_RETRIES) != 1)
1314 goto abituguru_probe_error;
1315 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK2+1, i,
1316 data->bank2_settings[i], 2,
1317 ABIT_UGURU_MAX_RETRIES) != 2)
1318 goto abituguru_probe_error;
1319 }
1320 for (i = 0; i < ABIT_UGURU_MAX_PWMS; i++) {
1321 if (abituguru_read(data, ABIT_UGURU_FAN_PWM, i,
1322 data->pwm_settings[i], 5,
1323 ABIT_UGURU_MAX_RETRIES) != 5)
1324 goto abituguru_probe_error;
1325 }
1326 data->last_updated = jiffies;
1327
1328 /* Detect sensor types and fill the sysfs attr for bank1 */
1329 sysfs_attr_i = 0;
1330 sysfs_filename = data->sysfs_names;
1331 sysfs_names_free = ABITUGURU_SYSFS_NAMES_LENGTH;
1332 for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
1333 res = abituguru_detect_bank1_sensor_type(data, probe_order[i]);
1334 if (res < 0)
1335 goto abituguru_probe_error;
1336 if (res == ABIT_UGURU_NC)
1337 continue;
1338
1339 /* res 1 (temp) sensors have 7 sysfs entries, 0 (in) 9 */
1340 for (j = 0; j < (res ? 7 : 9); j++) {
1341 used = snprintf(sysfs_filename, sysfs_names_free,
1342 abituguru_sysfs_bank1_templ[res][j].dev_attr.
1343 attr.name, data->bank1_sensors[res] + res)
1344 + 1;
1345 data->sysfs_attr[sysfs_attr_i] =
1346 abituguru_sysfs_bank1_templ[res][j];
1347 data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
1348 sysfs_filename;
1349 data->sysfs_attr[sysfs_attr_i].index = probe_order[i];
1350 sysfs_filename += used;
1351 sysfs_names_free -= used;
1352 sysfs_attr_i++;
1353 }
1354 data->bank1_max_value[probe_order[i]] =
1355 abituguru_bank1_max_value[res];
1356 data->bank1_address[res][data->bank1_sensors[res]] =
1357 probe_order[i];
1358 data->bank1_sensors[res]++;
1359 }
1360 /* Detect number of sensors and fill the sysfs attr for bank2 (fans) */
1361 abituguru_detect_no_bank2_sensors(data);
1362 for (i = 0; i < data->bank2_sensors; i++) {
1363 for (j = 0; j < ARRAY_SIZE(abituguru_sysfs_fan_templ); j++) {
1364 used = snprintf(sysfs_filename, sysfs_names_free,
1365 abituguru_sysfs_fan_templ[j].dev_attr.attr.name,
1366 i + 1) + 1;
1367 data->sysfs_attr[sysfs_attr_i] =
1368 abituguru_sysfs_fan_templ[j];
1369 data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
1370 sysfs_filename;
1371 data->sysfs_attr[sysfs_attr_i].index = i;
1372 sysfs_filename += used;
1373 sysfs_names_free -= used;
1374 sysfs_attr_i++;
1375 }
1376 }
1377 /* Detect number of sensors and fill the sysfs attr for pwms */
1378 abituguru_detect_no_pwms(data);
1379 for (i = 0; i < data->pwms; i++) {
1380 for (j = 0; j < ARRAY_SIZE(abituguru_sysfs_pwm_templ); j++) {
1381 used = snprintf(sysfs_filename, sysfs_names_free,
1382 abituguru_sysfs_pwm_templ[j].dev_attr.attr.name,
1383 i + 1) + 1;
1384 data->sysfs_attr[sysfs_attr_i] =
1385 abituguru_sysfs_pwm_templ[j];
1386 data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
1387 sysfs_filename;
1388 data->sysfs_attr[sysfs_attr_i].index = i;
1389 sysfs_filename += used;
1390 sysfs_names_free -= used;
1391 sysfs_attr_i++;
1392 }
1393 }
1394 /* Fail safe check, this should never happen! */
1395 if (sysfs_names_free < 0) {
1396 pr_err("Fatal error ran out of space for sysfs attr names. %s %s",
1397 never_happen, report_this);
1398 res = -ENAMETOOLONG;
1399 goto abituguru_probe_error;
1400 }
1401 pr_info("found Abit uGuru\n");
1402
1403 /* Register sysfs hooks */
1404 for (i = 0; i < sysfs_attr_i; i++) {
1405 res = device_create_file(&pdev->dev,
1406 &data->sysfs_attr[i].dev_attr);
1407 if (res)
1408 goto abituguru_probe_error;
1409 }
1410 for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++) {
1411 res = device_create_file(&pdev->dev,
1412 &abituguru_sysfs_attr[i].dev_attr);
1413 if (res)
1414 goto abituguru_probe_error;
1415 }
1416
1417 data->hwmon_dev = hwmon_device_register(&pdev->dev);
1418 if (!IS_ERR(data->hwmon_dev))
1419 return 0; /* success */
1420
1421 res = PTR_ERR(data->hwmon_dev);
1422abituguru_probe_error:
1423 for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++)
1424 device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
1425 for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++)
1426 device_remove_file(&pdev->dev,
1427 &abituguru_sysfs_attr[i].dev_attr);
1428 return res;
1429}
1430
1431static void abituguru_remove(struct platform_device *pdev)
1432{
1433 int i;
1434 struct abituguru_data *data = platform_get_drvdata(pdev);
1435
1436 hwmon_device_unregister(data->hwmon_dev);
1437 for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++)
1438 device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
1439 for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++)
1440 device_remove_file(&pdev->dev,
1441 &abituguru_sysfs_attr[i].dev_attr);
1442}
1443
1444static struct abituguru_data *abituguru_update_device(struct device *dev)
1445{
1446 int i, err;
1447 struct abituguru_data *data = dev_get_drvdata(dev);
1448 /* fake a complete successful read if no update necessary. */
1449 char success = 1;
1450
1451 mutex_lock(&data->update_lock);
1452 if (time_after(jiffies, data->last_updated + HZ)) {
1453 success = 0;
1454 err = abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0,
1455 data->alarms, 3, 0);
1456 if (err != 3)
1457 goto LEAVE_UPDATE;
1458 for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
1459 err = abituguru_read(data, ABIT_UGURU_SENSOR_BANK1,
1460 i, &data->bank1_value[i], 1, 0);
1461 if (err != 1)
1462 goto LEAVE_UPDATE;
1463 err = abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1,
1464 i, data->bank1_settings[i], 3, 0);
1465 if (err != 3)
1466 goto LEAVE_UPDATE;
1467 }
1468 for (i = 0; i < data->bank2_sensors; i++) {
1469 err = abituguru_read(data, ABIT_UGURU_SENSOR_BANK2, i,
1470 &data->bank2_value[i], 1, 0);
1471 if (err != 1)
1472 goto LEAVE_UPDATE;
1473 }
1474 /* success! */
1475 success = 1;
1476 data->update_timeouts = 0;
1477LEAVE_UPDATE:
1478 /* handle timeout condition */
1479 if (!success && (err == -EBUSY || err >= 0)) {
1480 /* No overflow please */
1481 if (data->update_timeouts < 255u)
1482 data->update_timeouts++;
1483 if (data->update_timeouts <= ABIT_UGURU_MAX_TIMEOUTS) {
1484 ABIT_UGURU_DEBUG(3, "timeout exceeded, will "
1485 "try again next update\n");
1486 /* Just a timeout, fake a successful read */
1487 success = 1;
1488 } else
1489 ABIT_UGURU_DEBUG(1, "timeout exceeded %d "
1490 "times waiting for more input state\n",
1491 (int)data->update_timeouts);
1492 }
1493 /* On success set last_updated */
1494 if (success)
1495 data->last_updated = jiffies;
1496 }
1497 mutex_unlock(&data->update_lock);
1498
1499 if (success)
1500 return data;
1501 else
1502 return NULL;
1503}
1504
1505static int abituguru_suspend(struct device *dev)
1506{
1507 struct abituguru_data *data = dev_get_drvdata(dev);
1508 /*
1509 * make sure all communications with the uguru are done and no new
1510 * ones are started
1511 */
1512 mutex_lock(&data->update_lock);
1513 return 0;
1514}
1515
1516static int abituguru_resume(struct device *dev)
1517{
1518 struct abituguru_data *data = dev_get_drvdata(dev);
1519 /* See if the uGuru is still ready */
1520 if (inb_p(data->addr + ABIT_UGURU_DATA) != ABIT_UGURU_STATUS_INPUT)
1521 data->uguru_ready = 0;
1522 mutex_unlock(&data->update_lock);
1523 return 0;
1524}
1525
1526static DEFINE_SIMPLE_DEV_PM_OPS(abituguru_pm, abituguru_suspend, abituguru_resume);
1527
1528static struct platform_driver abituguru_driver = {
1529 .driver = {
1530 .name = ABIT_UGURU_NAME,
1531 .pm = pm_sleep_ptr(&abituguru_pm),
1532 },
1533 .probe = abituguru_probe,
1534 .remove_new = abituguru_remove,
1535};
1536
1537static int __init abituguru_detect(void)
1538{
1539 /*
1540 * See if there is an uguru there. After a reboot uGuru will hold 0x00
1541 * at DATA and 0xAC, when this driver has already been loaded once
1542 * DATA will hold 0x08. For most uGuru's CMD will hold 0xAC in either
1543 * scenario but some will hold 0x00.
1544 * Some uGuru's initially hold 0x09 at DATA and will only hold 0x08
1545 * after reading CMD first, so CMD must be read first!
1546 */
1547 u8 cmd_val = inb_p(ABIT_UGURU_BASE + ABIT_UGURU_CMD);
1548 u8 data_val = inb_p(ABIT_UGURU_BASE + ABIT_UGURU_DATA);
1549 if (((data_val == 0x00) || (data_val == 0x08)) &&
1550 ((cmd_val == 0x00) || (cmd_val == 0xAC)))
1551 return ABIT_UGURU_BASE;
1552
1553 ABIT_UGURU_DEBUG(2, "no Abit uGuru found, data = 0x%02X, cmd = "
1554 "0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val);
1555
1556 if (force) {
1557 pr_info("Assuming Abit uGuru is present because of \"force\" parameter\n");
1558 return ABIT_UGURU_BASE;
1559 }
1560
1561 /* No uGuru found */
1562 return -ENODEV;
1563}
1564
1565static struct platform_device *abituguru_pdev;
1566
1567static int __init abituguru_init(void)
1568{
1569 int address, err;
1570 struct resource res = { .flags = IORESOURCE_IO };
1571 const char *board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR);
1572
1573 /* safety check, refuse to load on non Abit motherboards */
1574 if (!force && (!board_vendor ||
1575 strcmp(board_vendor, "http://www.abit.com.tw/")))
1576 return -ENODEV;
1577
1578 address = abituguru_detect();
1579 if (address < 0)
1580 return address;
1581
1582 err = platform_driver_register(&abituguru_driver);
1583 if (err)
1584 goto exit;
1585
1586 abituguru_pdev = platform_device_alloc(ABIT_UGURU_NAME, address);
1587 if (!abituguru_pdev) {
1588 pr_err("Device allocation failed\n");
1589 err = -ENOMEM;
1590 goto exit_driver_unregister;
1591 }
1592
1593 res.start = address;
1594 res.end = address + ABIT_UGURU_REGION_LENGTH - 1;
1595 res.name = ABIT_UGURU_NAME;
1596
1597 err = platform_device_add_resources(abituguru_pdev, &res, 1);
1598 if (err) {
1599 pr_err("Device resource addition failed (%d)\n", err);
1600 goto exit_device_put;
1601 }
1602
1603 err = platform_device_add(abituguru_pdev);
1604 if (err) {
1605 pr_err("Device addition failed (%d)\n", err);
1606 goto exit_device_put;
1607 }
1608
1609 return 0;
1610
1611exit_device_put:
1612 platform_device_put(abituguru_pdev);
1613exit_driver_unregister:
1614 platform_driver_unregister(&abituguru_driver);
1615exit:
1616 return err;
1617}
1618
1619static void __exit abituguru_exit(void)
1620{
1621 platform_device_unregister(abituguru_pdev);
1622 platform_driver_unregister(&abituguru_driver);
1623}
1624
1625MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
1626MODULE_DESCRIPTION("Abit uGuru Sensor device");
1627MODULE_LICENSE("GPL");
1628
1629module_init(abituguru_init);
1630module_exit(abituguru_exit);
1/*
2 * abituguru.c Copyright (c) 2005-2006 Hans de Goede <hdegoede@redhat.com>
3 *
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License as published by
6 * the Free Software Foundation; either version 2 of the License, or
7 * (at your option) any later version.
8 *
9 * This program is distributed in the hope that it will be useful,
10 * but WITHOUT ANY WARRANTY; without even the implied warranty of
11 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
12 * GNU General Public License for more details.
13 *
14 * You should have received a copy of the GNU General Public License
15 * along with this program; if not, write to the Free Software
16 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
17 */
18/*
19 * This driver supports the sensor part of the first and second revision of
20 * the custom Abit uGuru chip found on Abit uGuru motherboards. Note: because
21 * of lack of specs the CPU/RAM voltage & frequency control is not supported!
22 */
23
24#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
25
26#include <linux/module.h>
27#include <linux/sched.h>
28#include <linux/init.h>
29#include <linux/slab.h>
30#include <linux/jiffies.h>
31#include <linux/mutex.h>
32#include <linux/err.h>
33#include <linux/delay.h>
34#include <linux/platform_device.h>
35#include <linux/hwmon.h>
36#include <linux/hwmon-sysfs.h>
37#include <linux/dmi.h>
38#include <linux/io.h>
39
40/* Banks */
41#define ABIT_UGURU_ALARM_BANK 0x20 /* 1x 3 bytes */
42#define ABIT_UGURU_SENSOR_BANK1 0x21 /* 16x volt and temp */
43#define ABIT_UGURU_FAN_PWM 0x24 /* 3x 5 bytes */
44#define ABIT_UGURU_SENSOR_BANK2 0x26 /* fans */
45/* max nr of sensors in bank1, a bank1 sensor can be in, temp or nc */
46#define ABIT_UGURU_MAX_BANK1_SENSORS 16
47/*
48 * Warning if you increase one of the 2 MAX defines below to 10 or higher you
49 * should adjust the belonging _NAMES_LENGTH macro for the 2 digit number!
50 */
51/* max nr of sensors in bank2, currently mb's with max 6 fans are known */
52#define ABIT_UGURU_MAX_BANK2_SENSORS 6
53/* max nr of pwm outputs, currently mb's with max 5 pwm outputs are known */
54#define ABIT_UGURU_MAX_PWMS 5
55/* uGuru sensor bank 1 flags */ /* Alarm if: */
56#define ABIT_UGURU_TEMP_HIGH_ALARM_ENABLE 0x01 /* temp over warn */
57#define ABIT_UGURU_VOLT_HIGH_ALARM_ENABLE 0x02 /* volt over max */
58#define ABIT_UGURU_VOLT_LOW_ALARM_ENABLE 0x04 /* volt under min */
59#define ABIT_UGURU_TEMP_HIGH_ALARM_FLAG 0x10 /* temp is over warn */
60#define ABIT_UGURU_VOLT_HIGH_ALARM_FLAG 0x20 /* volt is over max */
61#define ABIT_UGURU_VOLT_LOW_ALARM_FLAG 0x40 /* volt is under min */
62/* uGuru sensor bank 2 flags */ /* Alarm if: */
63#define ABIT_UGURU_FAN_LOW_ALARM_ENABLE 0x01 /* fan under min */
64/* uGuru sensor bank common flags */
65#define ABIT_UGURU_BEEP_ENABLE 0x08 /* beep if alarm */
66#define ABIT_UGURU_SHUTDOWN_ENABLE 0x80 /* shutdown if alarm */
67/* uGuru fan PWM (speed control) flags */
68#define ABIT_UGURU_FAN_PWM_ENABLE 0x80 /* enable speed control */
69/* Values used for conversion */
70#define ABIT_UGURU_FAN_MAX 15300 /* RPM */
71/* Bank1 sensor types */
72#define ABIT_UGURU_IN_SENSOR 0
73#define ABIT_UGURU_TEMP_SENSOR 1
74#define ABIT_UGURU_NC 2
75/*
76 * In many cases we need to wait for the uGuru to reach a certain status, most
77 * of the time it will reach this status within 30 - 90 ISA reads, and thus we
78 * can best busy wait. This define gives the total amount of reads to try.
79 */
80#define ABIT_UGURU_WAIT_TIMEOUT 125
81/*
82 * However sometimes older versions of the uGuru seem to be distracted and they
83 * do not respond for a long time. To handle this we sleep before each of the
84 * last ABIT_UGURU_WAIT_TIMEOUT_SLEEP tries.
85 */
86#define ABIT_UGURU_WAIT_TIMEOUT_SLEEP 5
87/*
88 * Normally all expected status in abituguru_ready, are reported after the
89 * first read, but sometimes not and we need to poll.
90 */
91#define ABIT_UGURU_READY_TIMEOUT 5
92/* Maximum 3 retries on timedout reads/writes, delay 200 ms before retrying */
93#define ABIT_UGURU_MAX_RETRIES 3
94#define ABIT_UGURU_RETRY_DELAY (HZ/5)
95/* Maximum 2 timeouts in abituguru_update_device, iow 3 in a row is an error */
96#define ABIT_UGURU_MAX_TIMEOUTS 2
97/* utility macros */
98#define ABIT_UGURU_NAME "abituguru"
99#define ABIT_UGURU_DEBUG(level, format, arg...) \
100 do { \
101 if (level <= verbose) \
102 pr_debug(format , ## arg); \
103 } while (0)
104
105/* Macros to help calculate the sysfs_names array length */
106/*
107 * sum of strlen of: in??_input\0, in??_{min,max}\0, in??_{min,max}_alarm\0,
108 * in??_{min,max}_alarm_enable\0, in??_beep\0, in??_shutdown\0
109 */
110#define ABITUGURU_IN_NAMES_LENGTH (11 + 2 * 9 + 2 * 15 + 2 * 22 + 10 + 14)
111/*
112 * sum of strlen of: temp??_input\0, temp??_max\0, temp??_crit\0,
113 * temp??_alarm\0, temp??_alarm_enable\0, temp??_beep\0, temp??_shutdown\0
114 */
115#define ABITUGURU_TEMP_NAMES_LENGTH (13 + 11 + 12 + 13 + 20 + 12 + 16)
116/*
117 * sum of strlen of: fan?_input\0, fan?_min\0, fan?_alarm\0,
118 * fan?_alarm_enable\0, fan?_beep\0, fan?_shutdown\0
119 */
120#define ABITUGURU_FAN_NAMES_LENGTH (11 + 9 + 11 + 18 + 10 + 14)
121/*
122 * sum of strlen of: pwm?_enable\0, pwm?_auto_channels_temp\0,
123 * pwm?_auto_point{1,2}_pwm\0, pwm?_auto_point{1,2}_temp\0
124 */
125#define ABITUGURU_PWM_NAMES_LENGTH (12 + 24 + 2 * 21 + 2 * 22)
126/* IN_NAMES_LENGTH > TEMP_NAMES_LENGTH so assume all bank1 sensors are in */
127#define ABITUGURU_SYSFS_NAMES_LENGTH ( \
128 ABIT_UGURU_MAX_BANK1_SENSORS * ABITUGURU_IN_NAMES_LENGTH + \
129 ABIT_UGURU_MAX_BANK2_SENSORS * ABITUGURU_FAN_NAMES_LENGTH + \
130 ABIT_UGURU_MAX_PWMS * ABITUGURU_PWM_NAMES_LENGTH)
131
132/*
133 * All the macros below are named identical to the oguru and oguru2 programs
134 * reverse engineered by Olle Sandberg, hence the names might not be 100%
135 * logical. I could come up with better names, but I prefer keeping the names
136 * identical so that this driver can be compared with his work more easily.
137 */
138/* Two i/o-ports are used by uGuru */
139#define ABIT_UGURU_BASE 0x00E0
140/* Used to tell uGuru what to read and to read the actual data */
141#define ABIT_UGURU_CMD 0x00
142/* Mostly used to check if uGuru is busy */
143#define ABIT_UGURU_DATA 0x04
144#define ABIT_UGURU_REGION_LENGTH 5
145/* uGuru status' */
146#define ABIT_UGURU_STATUS_WRITE 0x00 /* Ready to be written */
147#define ABIT_UGURU_STATUS_READ 0x01 /* Ready to be read */
148#define ABIT_UGURU_STATUS_INPUT 0x08 /* More input */
149#define ABIT_UGURU_STATUS_READY 0x09 /* Ready to be written */
150
151/* Constants */
152/* in (Volt) sensors go up to 3494 mV, temp to 255000 millidegrees Celsius */
153static const int abituguru_bank1_max_value[2] = { 3494, 255000 };
154/*
155 * Min / Max allowed values for sensor2 (fan) alarm threshold, these values
156 * correspond to 300-3000 RPM
157 */
158static const u8 abituguru_bank2_min_threshold = 5;
159static const u8 abituguru_bank2_max_threshold = 50;
160/*
161 * Register 0 is a bitfield, 1 and 2 are pwm settings (255 = 100%), 3 and 4
162 * are temperature trip points.
163 */
164static const int abituguru_pwm_settings_multiplier[5] = { 0, 1, 1, 1000, 1000 };
165/*
166 * Min / Max allowed values for pwm_settings. Note: pwm1 (CPU fan) is a
167 * special case the minimum allowed pwm% setting for this is 30% (77) on
168 * some MB's this special case is handled in the code!
169 */
170static const u8 abituguru_pwm_min[5] = { 0, 170, 170, 25, 25 };
171static const u8 abituguru_pwm_max[5] = { 0, 255, 255, 75, 75 };
172
173
174/* Insmod parameters */
175static bool force;
176module_param(force, bool, 0);
177MODULE_PARM_DESC(force, "Set to one to force detection.");
178static int bank1_types[ABIT_UGURU_MAX_BANK1_SENSORS] = { -1, -1, -1, -1, -1,
179 -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1 };
180module_param_array(bank1_types, int, NULL, 0);
181MODULE_PARM_DESC(bank1_types, "Bank1 sensortype autodetection override:\n"
182 " -1 autodetect\n"
183 " 0 volt sensor\n"
184 " 1 temp sensor\n"
185 " 2 not connected");
186static int fan_sensors;
187module_param(fan_sensors, int, 0);
188MODULE_PARM_DESC(fan_sensors, "Number of fan sensors on the uGuru "
189 "(0 = autodetect)");
190static int pwms;
191module_param(pwms, int, 0);
192MODULE_PARM_DESC(pwms, "Number of PWMs on the uGuru "
193 "(0 = autodetect)");
194
195/* Default verbose is 2, since this driver is still in the testing phase */
196static int verbose = 2;
197module_param(verbose, int, 0644);
198MODULE_PARM_DESC(verbose, "How verbose should the driver be? (0-3):\n"
199 " 0 normal output\n"
200 " 1 + verbose error reporting\n"
201 " 2 + sensors type probing info\n"
202 " 3 + retryable error reporting");
203
204
205/*
206 * For the Abit uGuru, we need to keep some data in memory.
207 * The structure is dynamically allocated, at the same time when a new
208 * abituguru device is allocated.
209 */
210struct abituguru_data {
211 struct device *hwmon_dev; /* hwmon registered device */
212 struct mutex update_lock; /* protect access to data and uGuru */
213 unsigned long last_updated; /* In jiffies */
214 unsigned short addr; /* uguru base address */
215 char uguru_ready; /* is the uguru in ready state? */
216 unsigned char update_timeouts; /*
217 * number of update timeouts since last
218 * successful update
219 */
220
221 /*
222 * The sysfs attr and their names are generated automatically, for bank1
223 * we cannot use a predefined array because we don't know beforehand
224 * of a sensor is a volt or a temp sensor, for bank2 and the pwms its
225 * easier todo things the same way. For in sensors we have 9 (temp 7)
226 * sysfs entries per sensor, for bank2 and pwms 6.
227 */
228 struct sensor_device_attribute_2 sysfs_attr[
229 ABIT_UGURU_MAX_BANK1_SENSORS * 9 +
230 ABIT_UGURU_MAX_BANK2_SENSORS * 6 + ABIT_UGURU_MAX_PWMS * 6];
231 /* Buffer to store the dynamically generated sysfs names */
232 char sysfs_names[ABITUGURU_SYSFS_NAMES_LENGTH];
233
234 /* Bank 1 data */
235 /* number of and addresses of [0] in, [1] temp sensors */
236 u8 bank1_sensors[2];
237 u8 bank1_address[2][ABIT_UGURU_MAX_BANK1_SENSORS];
238 u8 bank1_value[ABIT_UGURU_MAX_BANK1_SENSORS];
239 /*
240 * This array holds 3 entries per sensor for the bank 1 sensor settings
241 * (flags, min, max for voltage / flags, warn, shutdown for temp).
242 */
243 u8 bank1_settings[ABIT_UGURU_MAX_BANK1_SENSORS][3];
244 /*
245 * Maximum value for each sensor used for scaling in mV/millidegrees
246 * Celsius.
247 */
248 int bank1_max_value[ABIT_UGURU_MAX_BANK1_SENSORS];
249
250 /* Bank 2 data, ABIT_UGURU_MAX_BANK2_SENSORS entries for bank2 */
251 u8 bank2_sensors; /* actual number of bank2 sensors found */
252 u8 bank2_value[ABIT_UGURU_MAX_BANK2_SENSORS];
253 u8 bank2_settings[ABIT_UGURU_MAX_BANK2_SENSORS][2]; /* flags, min */
254
255 /* Alarms 2 bytes for bank1, 1 byte for bank2 */
256 u8 alarms[3];
257
258 /* Fan PWM (speed control) 5 bytes per PWM */
259 u8 pwms; /* actual number of pwms found */
260 u8 pwm_settings[ABIT_UGURU_MAX_PWMS][5];
261};
262
263static const char *never_happen = "This should never happen.";
264static const char *report_this =
265 "Please report this to the abituguru maintainer (see MAINTAINERS)";
266
267/* wait till the uguru is in the specified state */
268static int abituguru_wait(struct abituguru_data *data, u8 state)
269{
270 int timeout = ABIT_UGURU_WAIT_TIMEOUT;
271
272 while (inb_p(data->addr + ABIT_UGURU_DATA) != state) {
273 timeout--;
274 if (timeout == 0)
275 return -EBUSY;
276 /*
277 * sleep a bit before our last few tries, see the comment on
278 * this where ABIT_UGURU_WAIT_TIMEOUT_SLEEP is defined.
279 */
280 if (timeout <= ABIT_UGURU_WAIT_TIMEOUT_SLEEP)
281 msleep(0);
282 }
283 return 0;
284}
285
286/* Put the uguru in ready for input state */
287static int abituguru_ready(struct abituguru_data *data)
288{
289 int timeout = ABIT_UGURU_READY_TIMEOUT;
290
291 if (data->uguru_ready)
292 return 0;
293
294 /* Reset? / Prepare for next read/write cycle */
295 outb(0x00, data->addr + ABIT_UGURU_DATA);
296
297 /* Wait till the uguru is ready */
298 if (abituguru_wait(data, ABIT_UGURU_STATUS_READY)) {
299 ABIT_UGURU_DEBUG(1,
300 "timeout exceeded waiting for ready state\n");
301 return -EIO;
302 }
303
304 /* Cmd port MUST be read now and should contain 0xAC */
305 while (inb_p(data->addr + ABIT_UGURU_CMD) != 0xAC) {
306 timeout--;
307 if (timeout == 0) {
308 ABIT_UGURU_DEBUG(1,
309 "CMD reg does not hold 0xAC after ready command\n");
310 return -EIO;
311 }
312 msleep(0);
313 }
314
315 /*
316 * After this the ABIT_UGURU_DATA port should contain
317 * ABIT_UGURU_STATUS_INPUT
318 */
319 timeout = ABIT_UGURU_READY_TIMEOUT;
320 while (inb_p(data->addr + ABIT_UGURU_DATA) != ABIT_UGURU_STATUS_INPUT) {
321 timeout--;
322 if (timeout == 0) {
323 ABIT_UGURU_DEBUG(1,
324 "state != more input after ready command\n");
325 return -EIO;
326 }
327 msleep(0);
328 }
329
330 data->uguru_ready = 1;
331 return 0;
332}
333
334/*
335 * Send the bank and then sensor address to the uGuru for the next read/write
336 * cycle. This function gets called as the first part of a read/write by
337 * abituguru_read and abituguru_write. This function should never be
338 * called by any other function.
339 */
340static int abituguru_send_address(struct abituguru_data *data,
341 u8 bank_addr, u8 sensor_addr, int retries)
342{
343 /*
344 * assume the caller does error handling itself if it has not requested
345 * any retries, and thus be quiet.
346 */
347 int report_errors = retries;
348
349 for (;;) {
350 /*
351 * Make sure the uguru is ready and then send the bank address,
352 * after this the uguru is no longer "ready".
353 */
354 if (abituguru_ready(data) != 0)
355 return -EIO;
356 outb(bank_addr, data->addr + ABIT_UGURU_DATA);
357 data->uguru_ready = 0;
358
359 /*
360 * Wait till the uguru is ABIT_UGURU_STATUS_INPUT state again
361 * and send the sensor addr
362 */
363 if (abituguru_wait(data, ABIT_UGURU_STATUS_INPUT)) {
364 if (retries) {
365 ABIT_UGURU_DEBUG(3, "timeout exceeded "
366 "waiting for more input state, %d "
367 "tries remaining\n", retries);
368 set_current_state(TASK_UNINTERRUPTIBLE);
369 schedule_timeout(ABIT_UGURU_RETRY_DELAY);
370 retries--;
371 continue;
372 }
373 if (report_errors)
374 ABIT_UGURU_DEBUG(1, "timeout exceeded "
375 "waiting for more input state "
376 "(bank: %d)\n", (int)bank_addr);
377 return -EBUSY;
378 }
379 outb(sensor_addr, data->addr + ABIT_UGURU_CMD);
380 return 0;
381 }
382}
383
384/*
385 * Read count bytes from sensor sensor_addr in bank bank_addr and store the
386 * result in buf, retry the send address part of the read retries times.
387 */
388static int abituguru_read(struct abituguru_data *data,
389 u8 bank_addr, u8 sensor_addr, u8 *buf, int count, int retries)
390{
391 int i;
392
393 /* Send the address */
394 i = abituguru_send_address(data, bank_addr, sensor_addr, retries);
395 if (i)
396 return i;
397
398 /* And read the data */
399 for (i = 0; i < count; i++) {
400 if (abituguru_wait(data, ABIT_UGURU_STATUS_READ)) {
401 ABIT_UGURU_DEBUG(retries ? 1 : 3,
402 "timeout exceeded waiting for "
403 "read state (bank: %d, sensor: %d)\n",
404 (int)bank_addr, (int)sensor_addr);
405 break;
406 }
407 buf[i] = inb(data->addr + ABIT_UGURU_CMD);
408 }
409
410 /* Last put the chip back in ready state */
411 abituguru_ready(data);
412
413 return i;
414}
415
416/*
417 * Write count bytes from buf to sensor sensor_addr in bank bank_addr, the send
418 * address part of the write is always retried ABIT_UGURU_MAX_RETRIES times.
419 */
420static int abituguru_write(struct abituguru_data *data,
421 u8 bank_addr, u8 sensor_addr, u8 *buf, int count)
422{
423 /*
424 * We use the ready timeout as we have to wait for 0xAC just like the
425 * ready function
426 */
427 int i, timeout = ABIT_UGURU_READY_TIMEOUT;
428
429 /* Send the address */
430 i = abituguru_send_address(data, bank_addr, sensor_addr,
431 ABIT_UGURU_MAX_RETRIES);
432 if (i)
433 return i;
434
435 /* And write the data */
436 for (i = 0; i < count; i++) {
437 if (abituguru_wait(data, ABIT_UGURU_STATUS_WRITE)) {
438 ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for "
439 "write state (bank: %d, sensor: %d)\n",
440 (int)bank_addr, (int)sensor_addr);
441 break;
442 }
443 outb(buf[i], data->addr + ABIT_UGURU_CMD);
444 }
445
446 /*
447 * Now we need to wait till the chip is ready to be read again,
448 * so that we can read 0xAC as confirmation that our write has
449 * succeeded.
450 */
451 if (abituguru_wait(data, ABIT_UGURU_STATUS_READ)) {
452 ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for read state "
453 "after write (bank: %d, sensor: %d)\n", (int)bank_addr,
454 (int)sensor_addr);
455 return -EIO;
456 }
457
458 /* Cmd port MUST be read now and should contain 0xAC */
459 while (inb_p(data->addr + ABIT_UGURU_CMD) != 0xAC) {
460 timeout--;
461 if (timeout == 0) {
462 ABIT_UGURU_DEBUG(1, "CMD reg does not hold 0xAC after "
463 "write (bank: %d, sensor: %d)\n",
464 (int)bank_addr, (int)sensor_addr);
465 return -EIO;
466 }
467 msleep(0);
468 }
469
470 /* Last put the chip back in ready state */
471 abituguru_ready(data);
472
473 return i;
474}
475
476/*
477 * Detect sensor type. Temp and Volt sensors are enabled with
478 * different masks and will ignore enable masks not meant for them.
479 * This enables us to test what kind of sensor we're dealing with.
480 * By setting the alarm thresholds so that we will always get an
481 * alarm for sensor type X and then enabling the sensor as sensor type
482 * X, if we then get an alarm it is a sensor of type X.
483 */
484static int
485abituguru_detect_bank1_sensor_type(struct abituguru_data *data,
486 u8 sensor_addr)
487{
488 u8 val, test_flag, buf[3];
489 int i, ret = -ENODEV; /* error is the most common used retval :| */
490
491 /* If overriden by the user return the user selected type */
492 if (bank1_types[sensor_addr] >= ABIT_UGURU_IN_SENSOR &&
493 bank1_types[sensor_addr] <= ABIT_UGURU_NC) {
494 ABIT_UGURU_DEBUG(2, "assuming sensor type %d for bank1 sensor "
495 "%d because of \"bank1_types\" module param\n",
496 bank1_types[sensor_addr], (int)sensor_addr);
497 return bank1_types[sensor_addr];
498 }
499
500 /* First read the sensor and the current settings */
501 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1, sensor_addr, &val,
502 1, ABIT_UGURU_MAX_RETRIES) != 1)
503 return -ENODEV;
504
505 /* Test val is sane / usable for sensor type detection. */
506 if ((val < 10u) || (val > 250u)) {
507 pr_warn("bank1-sensor: %d reading (%d) too close to limits, "
508 "unable to determine sensor type, skipping sensor\n",
509 (int)sensor_addr, (int)val);
510 /*
511 * assume no sensor is there for sensors for which we can't
512 * determine the sensor type because their reading is too close
513 * to their limits, this usually means no sensor is there.
514 */
515 return ABIT_UGURU_NC;
516 }
517
518 ABIT_UGURU_DEBUG(2, "testing bank1 sensor %d\n", (int)sensor_addr);
519 /*
520 * Volt sensor test, enable volt low alarm, set min value ridiculously
521 * high, or vica versa if the reading is very high. If its a volt
522 * sensor this should always give us an alarm.
523 */
524 if (val <= 240u) {
525 buf[0] = ABIT_UGURU_VOLT_LOW_ALARM_ENABLE;
526 buf[1] = 245;
527 buf[2] = 250;
528 test_flag = ABIT_UGURU_VOLT_LOW_ALARM_FLAG;
529 } else {
530 buf[0] = ABIT_UGURU_VOLT_HIGH_ALARM_ENABLE;
531 buf[1] = 5;
532 buf[2] = 10;
533 test_flag = ABIT_UGURU_VOLT_HIGH_ALARM_FLAG;
534 }
535
536 if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
537 buf, 3) != 3)
538 goto abituguru_detect_bank1_sensor_type_exit;
539 /*
540 * Now we need 20 ms to give the uguru time to read the sensors
541 * and raise a voltage alarm
542 */
543 set_current_state(TASK_UNINTERRUPTIBLE);
544 schedule_timeout(HZ/50);
545 /* Check for alarm and check the alarm is a volt low alarm. */
546 if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0, buf, 3,
547 ABIT_UGURU_MAX_RETRIES) != 3)
548 goto abituguru_detect_bank1_sensor_type_exit;
549 if (buf[sensor_addr/8] & (0x01 << (sensor_addr % 8))) {
550 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1,
551 sensor_addr, buf, 3,
552 ABIT_UGURU_MAX_RETRIES) != 3)
553 goto abituguru_detect_bank1_sensor_type_exit;
554 if (buf[0] & test_flag) {
555 ABIT_UGURU_DEBUG(2, " found volt sensor\n");
556 ret = ABIT_UGURU_IN_SENSOR;
557 goto abituguru_detect_bank1_sensor_type_exit;
558 } else
559 ABIT_UGURU_DEBUG(2, " alarm raised during volt "
560 "sensor test, but volt range flag not set\n");
561 } else
562 ABIT_UGURU_DEBUG(2, " alarm not raised during volt sensor "
563 "test\n");
564
565 /*
566 * Temp sensor test, enable sensor as a temp sensor, set beep value
567 * ridiculously low (but not too low, otherwise uguru ignores it).
568 * If its a temp sensor this should always give us an alarm.
569 */
570 buf[0] = ABIT_UGURU_TEMP_HIGH_ALARM_ENABLE;
571 buf[1] = 5;
572 buf[2] = 10;
573 if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
574 buf, 3) != 3)
575 goto abituguru_detect_bank1_sensor_type_exit;
576 /*
577 * Now we need 50 ms to give the uguru time to read the sensors
578 * and raise a temp alarm
579 */
580 set_current_state(TASK_UNINTERRUPTIBLE);
581 schedule_timeout(HZ/20);
582 /* Check for alarm and check the alarm is a temp high alarm. */
583 if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0, buf, 3,
584 ABIT_UGURU_MAX_RETRIES) != 3)
585 goto abituguru_detect_bank1_sensor_type_exit;
586 if (buf[sensor_addr/8] & (0x01 << (sensor_addr % 8))) {
587 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1,
588 sensor_addr, buf, 3,
589 ABIT_UGURU_MAX_RETRIES) != 3)
590 goto abituguru_detect_bank1_sensor_type_exit;
591 if (buf[0] & ABIT_UGURU_TEMP_HIGH_ALARM_FLAG) {
592 ABIT_UGURU_DEBUG(2, " found temp sensor\n");
593 ret = ABIT_UGURU_TEMP_SENSOR;
594 goto abituguru_detect_bank1_sensor_type_exit;
595 } else
596 ABIT_UGURU_DEBUG(2, " alarm raised during temp "
597 "sensor test, but temp high flag not set\n");
598 } else
599 ABIT_UGURU_DEBUG(2, " alarm not raised during temp sensor "
600 "test\n");
601
602 ret = ABIT_UGURU_NC;
603abituguru_detect_bank1_sensor_type_exit:
604 /*
605 * Restore original settings, failing here is really BAD, it has been
606 * reported that some BIOS-es hang when entering the uGuru menu with
607 * invalid settings present in the uGuru, so we try this 3 times.
608 */
609 for (i = 0; i < 3; i++)
610 if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2,
611 sensor_addr, data->bank1_settings[sensor_addr],
612 3) == 3)
613 break;
614 if (i == 3) {
615 pr_err("Fatal error could not restore original settings. %s %s\n",
616 never_happen, report_this);
617 return -ENODEV;
618 }
619 return ret;
620}
621
622/*
623 * These functions try to find out how many sensors there are in bank2 and how
624 * many pwms there are. The purpose of this is to make sure that we don't give
625 * the user the possibility to change settings for non-existent sensors / pwm.
626 * The uGuru will happily read / write whatever memory happens to be after the
627 * memory storing the PWM settings when reading/writing to a PWM which is not
628 * there. Notice even if we detect a PWM which doesn't exist we normally won't
629 * write to it, unless the user tries to change the settings.
630 *
631 * Although the uGuru allows reading (settings) from non existing bank2
632 * sensors, my version of the uGuru does seem to stop writing to them, the
633 * write function above aborts in this case with:
634 * "CMD reg does not hold 0xAC after write"
635 *
636 * Notice these 2 tests are non destructive iow read-only tests, otherwise
637 * they would defeat their purpose. Although for the bank2_sensors detection a
638 * read/write test would be feasible because of the reaction above, I've
639 * however opted to stay on the safe side.
640 */
641static void
642abituguru_detect_no_bank2_sensors(struct abituguru_data *data)
643{
644 int i;
645
646 if (fan_sensors > 0 && fan_sensors <= ABIT_UGURU_MAX_BANK2_SENSORS) {
647 data->bank2_sensors = fan_sensors;
648 ABIT_UGURU_DEBUG(2, "assuming %d fan sensors because of "
649 "\"fan_sensors\" module param\n",
650 (int)data->bank2_sensors);
651 return;
652 }
653
654 ABIT_UGURU_DEBUG(2, "detecting number of fan sensors\n");
655 for (i = 0; i < ABIT_UGURU_MAX_BANK2_SENSORS; i++) {
656 /*
657 * 0x89 are the known used bits:
658 * -0x80 enable shutdown
659 * -0x08 enable beep
660 * -0x01 enable alarm
661 * All other bits should be 0, but on some motherboards
662 * 0x40 (bit 6) is also high for some of the fans??
663 */
664 if (data->bank2_settings[i][0] & ~0xC9) {
665 ABIT_UGURU_DEBUG(2, " bank2 sensor %d does not seem "
666 "to be a fan sensor: settings[0] = %02X\n",
667 i, (unsigned int)data->bank2_settings[i][0]);
668 break;
669 }
670
671 /* check if the threshold is within the allowed range */
672 if (data->bank2_settings[i][1] <
673 abituguru_bank2_min_threshold) {
674 ABIT_UGURU_DEBUG(2, " bank2 sensor %d does not seem "
675 "to be a fan sensor: the threshold (%d) is "
676 "below the minimum (%d)\n", i,
677 (int)data->bank2_settings[i][1],
678 (int)abituguru_bank2_min_threshold);
679 break;
680 }
681 if (data->bank2_settings[i][1] >
682 abituguru_bank2_max_threshold) {
683 ABIT_UGURU_DEBUG(2, " bank2 sensor %d does not seem "
684 "to be a fan sensor: the threshold (%d) is "
685 "above the maximum (%d)\n", i,
686 (int)data->bank2_settings[i][1],
687 (int)abituguru_bank2_max_threshold);
688 break;
689 }
690 }
691
692 data->bank2_sensors = i;
693 ABIT_UGURU_DEBUG(2, " found: %d fan sensors\n",
694 (int)data->bank2_sensors);
695}
696
697static void
698abituguru_detect_no_pwms(struct abituguru_data *data)
699{
700 int i, j;
701
702 if (pwms > 0 && pwms <= ABIT_UGURU_MAX_PWMS) {
703 data->pwms = pwms;
704 ABIT_UGURU_DEBUG(2, "assuming %d PWM outputs because of "
705 "\"pwms\" module param\n", (int)data->pwms);
706 return;
707 }
708
709 ABIT_UGURU_DEBUG(2, "detecting number of PWM outputs\n");
710 for (i = 0; i < ABIT_UGURU_MAX_PWMS; i++) {
711 /*
712 * 0x80 is the enable bit and the low
713 * nibble is which temp sensor to use,
714 * the other bits should be 0
715 */
716 if (data->pwm_settings[i][0] & ~0x8F) {
717 ABIT_UGURU_DEBUG(2, " pwm channel %d does not seem "
718 "to be a pwm channel: settings[0] = %02X\n",
719 i, (unsigned int)data->pwm_settings[i][0]);
720 break;
721 }
722
723 /*
724 * the low nibble must correspond to one of the temp sensors
725 * we've found
726 */
727 for (j = 0; j < data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR];
728 j++) {
729 if (data->bank1_address[ABIT_UGURU_TEMP_SENSOR][j] ==
730 (data->pwm_settings[i][0] & 0x0F))
731 break;
732 }
733 if (j == data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR]) {
734 ABIT_UGURU_DEBUG(2, " pwm channel %d does not seem "
735 "to be a pwm channel: %d is not a valid temp "
736 "sensor address\n", i,
737 data->pwm_settings[i][0] & 0x0F);
738 break;
739 }
740
741 /* check if all other settings are within the allowed range */
742 for (j = 1; j < 5; j++) {
743 u8 min;
744 /* special case pwm1 min pwm% */
745 if ((i == 0) && ((j == 1) || (j == 2)))
746 min = 77;
747 else
748 min = abituguru_pwm_min[j];
749 if (data->pwm_settings[i][j] < min) {
750 ABIT_UGURU_DEBUG(2, " pwm channel %d does "
751 "not seem to be a pwm channel: "
752 "setting %d (%d) is below the minimum "
753 "value (%d)\n", i, j,
754 (int)data->pwm_settings[i][j],
755 (int)min);
756 goto abituguru_detect_no_pwms_exit;
757 }
758 if (data->pwm_settings[i][j] > abituguru_pwm_max[j]) {
759 ABIT_UGURU_DEBUG(2, " pwm channel %d does "
760 "not seem to be a pwm channel: "
761 "setting %d (%d) is above the maximum "
762 "value (%d)\n", i, j,
763 (int)data->pwm_settings[i][j],
764 (int)abituguru_pwm_max[j]);
765 goto abituguru_detect_no_pwms_exit;
766 }
767 }
768
769 /* check that min temp < max temp and min pwm < max pwm */
770 if (data->pwm_settings[i][1] >= data->pwm_settings[i][2]) {
771 ABIT_UGURU_DEBUG(2, " pwm channel %d does not seem "
772 "to be a pwm channel: min pwm (%d) >= "
773 "max pwm (%d)\n", i,
774 (int)data->pwm_settings[i][1],
775 (int)data->pwm_settings[i][2]);
776 break;
777 }
778 if (data->pwm_settings[i][3] >= data->pwm_settings[i][4]) {
779 ABIT_UGURU_DEBUG(2, " pwm channel %d does not seem "
780 "to be a pwm channel: min temp (%d) >= "
781 "max temp (%d)\n", i,
782 (int)data->pwm_settings[i][3],
783 (int)data->pwm_settings[i][4]);
784 break;
785 }
786 }
787
788abituguru_detect_no_pwms_exit:
789 data->pwms = i;
790 ABIT_UGURU_DEBUG(2, " found: %d PWM outputs\n", (int)data->pwms);
791}
792
793/*
794 * Following are the sysfs callback functions. These functions expect:
795 * sensor_device_attribute_2->index: sensor address/offset in the bank
796 * sensor_device_attribute_2->nr: register offset, bitmask or NA.
797 */
798static struct abituguru_data *abituguru_update_device(struct device *dev);
799
800static ssize_t show_bank1_value(struct device *dev,
801 struct device_attribute *devattr, char *buf)
802{
803 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
804 struct abituguru_data *data = abituguru_update_device(dev);
805 if (!data)
806 return -EIO;
807 return sprintf(buf, "%d\n", (data->bank1_value[attr->index] *
808 data->bank1_max_value[attr->index] + 128) / 255);
809}
810
811static ssize_t show_bank1_setting(struct device *dev,
812 struct device_attribute *devattr, char *buf)
813{
814 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
815 struct abituguru_data *data = dev_get_drvdata(dev);
816 return sprintf(buf, "%d\n",
817 (data->bank1_settings[attr->index][attr->nr] *
818 data->bank1_max_value[attr->index] + 128) / 255);
819}
820
821static ssize_t show_bank2_value(struct device *dev,
822 struct device_attribute *devattr, char *buf)
823{
824 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
825 struct abituguru_data *data = abituguru_update_device(dev);
826 if (!data)
827 return -EIO;
828 return sprintf(buf, "%d\n", (data->bank2_value[attr->index] *
829 ABIT_UGURU_FAN_MAX + 128) / 255);
830}
831
832static ssize_t show_bank2_setting(struct device *dev,
833 struct device_attribute *devattr, char *buf)
834{
835 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
836 struct abituguru_data *data = dev_get_drvdata(dev);
837 return sprintf(buf, "%d\n",
838 (data->bank2_settings[attr->index][attr->nr] *
839 ABIT_UGURU_FAN_MAX + 128) / 255);
840}
841
842static ssize_t store_bank1_setting(struct device *dev, struct device_attribute
843 *devattr, const char *buf, size_t count)
844{
845 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
846 struct abituguru_data *data = dev_get_drvdata(dev);
847 unsigned long val;
848 ssize_t ret;
849
850 ret = kstrtoul(buf, 10, &val);
851 if (ret)
852 return ret;
853
854 ret = count;
855 val = (val * 255 + data->bank1_max_value[attr->index] / 2) /
856 data->bank1_max_value[attr->index];
857 if (val > 255)
858 return -EINVAL;
859
860 mutex_lock(&data->update_lock);
861 if (data->bank1_settings[attr->index][attr->nr] != val) {
862 u8 orig_val = data->bank1_settings[attr->index][attr->nr];
863 data->bank1_settings[attr->index][attr->nr] = val;
864 if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2,
865 attr->index, data->bank1_settings[attr->index],
866 3) <= attr->nr) {
867 data->bank1_settings[attr->index][attr->nr] = orig_val;
868 ret = -EIO;
869 }
870 }
871 mutex_unlock(&data->update_lock);
872 return ret;
873}
874
875static ssize_t store_bank2_setting(struct device *dev, struct device_attribute
876 *devattr, const char *buf, size_t count)
877{
878 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
879 struct abituguru_data *data = dev_get_drvdata(dev);
880 unsigned long val;
881 ssize_t ret;
882
883 ret = kstrtoul(buf, 10, &val);
884 if (ret)
885 return ret;
886
887 ret = count;
888 val = (val * 255 + ABIT_UGURU_FAN_MAX / 2) / ABIT_UGURU_FAN_MAX;
889
890 /* this check can be done before taking the lock */
891 if (val < abituguru_bank2_min_threshold ||
892 val > abituguru_bank2_max_threshold)
893 return -EINVAL;
894
895 mutex_lock(&data->update_lock);
896 if (data->bank2_settings[attr->index][attr->nr] != val) {
897 u8 orig_val = data->bank2_settings[attr->index][attr->nr];
898 data->bank2_settings[attr->index][attr->nr] = val;
899 if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK2 + 2,
900 attr->index, data->bank2_settings[attr->index],
901 2) <= attr->nr) {
902 data->bank2_settings[attr->index][attr->nr] = orig_val;
903 ret = -EIO;
904 }
905 }
906 mutex_unlock(&data->update_lock);
907 return ret;
908}
909
910static ssize_t show_bank1_alarm(struct device *dev,
911 struct device_attribute *devattr, char *buf)
912{
913 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
914 struct abituguru_data *data = abituguru_update_device(dev);
915 if (!data)
916 return -EIO;
917 /*
918 * See if the alarm bit for this sensor is set, and if the
919 * alarm matches the type of alarm we're looking for (for volt
920 * it can be either low or high). The type is stored in a few
921 * readonly bits in the settings part of the relevant sensor.
922 * The bitmask of the type is passed to us in attr->nr.
923 */
924 if ((data->alarms[attr->index / 8] & (0x01 << (attr->index % 8))) &&
925 (data->bank1_settings[attr->index][0] & attr->nr))
926 return sprintf(buf, "1\n");
927 else
928 return sprintf(buf, "0\n");
929}
930
931static ssize_t show_bank2_alarm(struct device *dev,
932 struct device_attribute *devattr, char *buf)
933{
934 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
935 struct abituguru_data *data = abituguru_update_device(dev);
936 if (!data)
937 return -EIO;
938 if (data->alarms[2] & (0x01 << attr->index))
939 return sprintf(buf, "1\n");
940 else
941 return sprintf(buf, "0\n");
942}
943
944static ssize_t show_bank1_mask(struct device *dev,
945 struct device_attribute *devattr, char *buf)
946{
947 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
948 struct abituguru_data *data = dev_get_drvdata(dev);
949 if (data->bank1_settings[attr->index][0] & attr->nr)
950 return sprintf(buf, "1\n");
951 else
952 return sprintf(buf, "0\n");
953}
954
955static ssize_t show_bank2_mask(struct device *dev,
956 struct device_attribute *devattr, char *buf)
957{
958 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
959 struct abituguru_data *data = dev_get_drvdata(dev);
960 if (data->bank2_settings[attr->index][0] & attr->nr)
961 return sprintf(buf, "1\n");
962 else
963 return sprintf(buf, "0\n");
964}
965
966static ssize_t store_bank1_mask(struct device *dev,
967 struct device_attribute *devattr, const char *buf, size_t count)
968{
969 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
970 struct abituguru_data *data = dev_get_drvdata(dev);
971 ssize_t ret;
972 u8 orig_val;
973 unsigned long mask;
974
975 ret = kstrtoul(buf, 10, &mask);
976 if (ret)
977 return ret;
978
979 ret = count;
980 mutex_lock(&data->update_lock);
981 orig_val = data->bank1_settings[attr->index][0];
982
983 if (mask)
984 data->bank1_settings[attr->index][0] |= attr->nr;
985 else
986 data->bank1_settings[attr->index][0] &= ~attr->nr;
987
988 if ((data->bank1_settings[attr->index][0] != orig_val) &&
989 (abituguru_write(data,
990 ABIT_UGURU_SENSOR_BANK1 + 2, attr->index,
991 data->bank1_settings[attr->index], 3) < 1)) {
992 data->bank1_settings[attr->index][0] = orig_val;
993 ret = -EIO;
994 }
995 mutex_unlock(&data->update_lock);
996 return ret;
997}
998
999static ssize_t store_bank2_mask(struct device *dev,
1000 struct device_attribute *devattr, const char *buf, size_t count)
1001{
1002 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
1003 struct abituguru_data *data = dev_get_drvdata(dev);
1004 ssize_t ret;
1005 u8 orig_val;
1006 unsigned long mask;
1007
1008 ret = kstrtoul(buf, 10, &mask);
1009 if (ret)
1010 return ret;
1011
1012 ret = count;
1013 mutex_lock(&data->update_lock);
1014 orig_val = data->bank2_settings[attr->index][0];
1015
1016 if (mask)
1017 data->bank2_settings[attr->index][0] |= attr->nr;
1018 else
1019 data->bank2_settings[attr->index][0] &= ~attr->nr;
1020
1021 if ((data->bank2_settings[attr->index][0] != orig_val) &&
1022 (abituguru_write(data,
1023 ABIT_UGURU_SENSOR_BANK2 + 2, attr->index,
1024 data->bank2_settings[attr->index], 2) < 1)) {
1025 data->bank2_settings[attr->index][0] = orig_val;
1026 ret = -EIO;
1027 }
1028 mutex_unlock(&data->update_lock);
1029 return ret;
1030}
1031
1032/* Fan PWM (speed control) */
1033static ssize_t show_pwm_setting(struct device *dev,
1034 struct device_attribute *devattr, char *buf)
1035{
1036 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
1037 struct abituguru_data *data = dev_get_drvdata(dev);
1038 return sprintf(buf, "%d\n", data->pwm_settings[attr->index][attr->nr] *
1039 abituguru_pwm_settings_multiplier[attr->nr]);
1040}
1041
1042static ssize_t store_pwm_setting(struct device *dev, struct device_attribute
1043 *devattr, const char *buf, size_t count)
1044{
1045 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
1046 struct abituguru_data *data = dev_get_drvdata(dev);
1047 u8 min;
1048 unsigned long val;
1049 ssize_t ret;
1050
1051 ret = kstrtoul(buf, 10, &val);
1052 if (ret)
1053 return ret;
1054
1055 ret = count;
1056 val = (val + abituguru_pwm_settings_multiplier[attr->nr] / 2) /
1057 abituguru_pwm_settings_multiplier[attr->nr];
1058
1059 /* special case pwm1 min pwm% */
1060 if ((attr->index == 0) && ((attr->nr == 1) || (attr->nr == 2)))
1061 min = 77;
1062 else
1063 min = abituguru_pwm_min[attr->nr];
1064
1065 /* this check can be done before taking the lock */
1066 if (val < min || val > abituguru_pwm_max[attr->nr])
1067 return -EINVAL;
1068
1069 mutex_lock(&data->update_lock);
1070 /* this check needs to be done after taking the lock */
1071 if ((attr->nr & 1) &&
1072 (val >= data->pwm_settings[attr->index][attr->nr + 1]))
1073 ret = -EINVAL;
1074 else if (!(attr->nr & 1) &&
1075 (val <= data->pwm_settings[attr->index][attr->nr - 1]))
1076 ret = -EINVAL;
1077 else if (data->pwm_settings[attr->index][attr->nr] != val) {
1078 u8 orig_val = data->pwm_settings[attr->index][attr->nr];
1079 data->pwm_settings[attr->index][attr->nr] = val;
1080 if (abituguru_write(data, ABIT_UGURU_FAN_PWM + 1,
1081 attr->index, data->pwm_settings[attr->index],
1082 5) <= attr->nr) {
1083 data->pwm_settings[attr->index][attr->nr] =
1084 orig_val;
1085 ret = -EIO;
1086 }
1087 }
1088 mutex_unlock(&data->update_lock);
1089 return ret;
1090}
1091
1092static ssize_t show_pwm_sensor(struct device *dev,
1093 struct device_attribute *devattr, char *buf)
1094{
1095 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
1096 struct abituguru_data *data = dev_get_drvdata(dev);
1097 int i;
1098 /*
1099 * We need to walk to the temp sensor addresses to find what
1100 * the userspace id of the configured temp sensor is.
1101 */
1102 for (i = 0; i < data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR]; i++)
1103 if (data->bank1_address[ABIT_UGURU_TEMP_SENSOR][i] ==
1104 (data->pwm_settings[attr->index][0] & 0x0F))
1105 return sprintf(buf, "%d\n", i+1);
1106
1107 return -ENXIO;
1108}
1109
1110static ssize_t store_pwm_sensor(struct device *dev, struct device_attribute
1111 *devattr, const char *buf, size_t count)
1112{
1113 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
1114 struct abituguru_data *data = dev_get_drvdata(dev);
1115 ssize_t ret;
1116 unsigned long val;
1117 u8 orig_val;
1118 u8 address;
1119
1120 ret = kstrtoul(buf, 10, &val);
1121 if (ret)
1122 return ret;
1123
1124 if (val == 0 || val > data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR])
1125 return -EINVAL;
1126
1127 val -= 1;
1128 ret = count;
1129 mutex_lock(&data->update_lock);
1130 orig_val = data->pwm_settings[attr->index][0];
1131 address = data->bank1_address[ABIT_UGURU_TEMP_SENSOR][val];
1132 data->pwm_settings[attr->index][0] &= 0xF0;
1133 data->pwm_settings[attr->index][0] |= address;
1134 if (data->pwm_settings[attr->index][0] != orig_val) {
1135 if (abituguru_write(data, ABIT_UGURU_FAN_PWM + 1, attr->index,
1136 data->pwm_settings[attr->index], 5) < 1) {
1137 data->pwm_settings[attr->index][0] = orig_val;
1138 ret = -EIO;
1139 }
1140 }
1141 mutex_unlock(&data->update_lock);
1142 return ret;
1143}
1144
1145static ssize_t show_pwm_enable(struct device *dev,
1146 struct device_attribute *devattr, char *buf)
1147{
1148 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
1149 struct abituguru_data *data = dev_get_drvdata(dev);
1150 int res = 0;
1151 if (data->pwm_settings[attr->index][0] & ABIT_UGURU_FAN_PWM_ENABLE)
1152 res = 2;
1153 return sprintf(buf, "%d\n", res);
1154}
1155
1156static ssize_t store_pwm_enable(struct device *dev, struct device_attribute
1157 *devattr, const char *buf, size_t count)
1158{
1159 struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
1160 struct abituguru_data *data = dev_get_drvdata(dev);
1161 u8 orig_val;
1162 ssize_t ret;
1163 unsigned long user_val;
1164
1165 ret = kstrtoul(buf, 10, &user_val);
1166 if (ret)
1167 return ret;
1168
1169 ret = count;
1170 mutex_lock(&data->update_lock);
1171 orig_val = data->pwm_settings[attr->index][0];
1172 switch (user_val) {
1173 case 0:
1174 data->pwm_settings[attr->index][0] &=
1175 ~ABIT_UGURU_FAN_PWM_ENABLE;
1176 break;
1177 case 2:
1178 data->pwm_settings[attr->index][0] |= ABIT_UGURU_FAN_PWM_ENABLE;
1179 break;
1180 default:
1181 ret = -EINVAL;
1182 }
1183 if ((data->pwm_settings[attr->index][0] != orig_val) &&
1184 (abituguru_write(data, ABIT_UGURU_FAN_PWM + 1,
1185 attr->index, data->pwm_settings[attr->index],
1186 5) < 1)) {
1187 data->pwm_settings[attr->index][0] = orig_val;
1188 ret = -EIO;
1189 }
1190 mutex_unlock(&data->update_lock);
1191 return ret;
1192}
1193
1194static ssize_t show_name(struct device *dev,
1195 struct device_attribute *devattr, char *buf)
1196{
1197 return sprintf(buf, "%s\n", ABIT_UGURU_NAME);
1198}
1199
1200/* Sysfs attr templates, the real entries are generated automatically. */
1201static const
1202struct sensor_device_attribute_2 abituguru_sysfs_bank1_templ[2][9] = {
1203 {
1204 SENSOR_ATTR_2(in%d_input, 0444, show_bank1_value, NULL, 0, 0),
1205 SENSOR_ATTR_2(in%d_min, 0644, show_bank1_setting,
1206 store_bank1_setting, 1, 0),
1207 SENSOR_ATTR_2(in%d_min_alarm, 0444, show_bank1_alarm, NULL,
1208 ABIT_UGURU_VOLT_LOW_ALARM_FLAG, 0),
1209 SENSOR_ATTR_2(in%d_max, 0644, show_bank1_setting,
1210 store_bank1_setting, 2, 0),
1211 SENSOR_ATTR_2(in%d_max_alarm, 0444, show_bank1_alarm, NULL,
1212 ABIT_UGURU_VOLT_HIGH_ALARM_FLAG, 0),
1213 SENSOR_ATTR_2(in%d_beep, 0644, show_bank1_mask,
1214 store_bank1_mask, ABIT_UGURU_BEEP_ENABLE, 0),
1215 SENSOR_ATTR_2(in%d_shutdown, 0644, show_bank1_mask,
1216 store_bank1_mask, ABIT_UGURU_SHUTDOWN_ENABLE, 0),
1217 SENSOR_ATTR_2(in%d_min_alarm_enable, 0644, show_bank1_mask,
1218 store_bank1_mask, ABIT_UGURU_VOLT_LOW_ALARM_ENABLE, 0),
1219 SENSOR_ATTR_2(in%d_max_alarm_enable, 0644, show_bank1_mask,
1220 store_bank1_mask, ABIT_UGURU_VOLT_HIGH_ALARM_ENABLE, 0),
1221 }, {
1222 SENSOR_ATTR_2(temp%d_input, 0444, show_bank1_value, NULL, 0, 0),
1223 SENSOR_ATTR_2(temp%d_alarm, 0444, show_bank1_alarm, NULL,
1224 ABIT_UGURU_TEMP_HIGH_ALARM_FLAG, 0),
1225 SENSOR_ATTR_2(temp%d_max, 0644, show_bank1_setting,
1226 store_bank1_setting, 1, 0),
1227 SENSOR_ATTR_2(temp%d_crit, 0644, show_bank1_setting,
1228 store_bank1_setting, 2, 0),
1229 SENSOR_ATTR_2(temp%d_beep, 0644, show_bank1_mask,
1230 store_bank1_mask, ABIT_UGURU_BEEP_ENABLE, 0),
1231 SENSOR_ATTR_2(temp%d_shutdown, 0644, show_bank1_mask,
1232 store_bank1_mask, ABIT_UGURU_SHUTDOWN_ENABLE, 0),
1233 SENSOR_ATTR_2(temp%d_alarm_enable, 0644, show_bank1_mask,
1234 store_bank1_mask, ABIT_UGURU_TEMP_HIGH_ALARM_ENABLE, 0),
1235 }
1236};
1237
1238static const struct sensor_device_attribute_2 abituguru_sysfs_fan_templ[6] = {
1239 SENSOR_ATTR_2(fan%d_input, 0444, show_bank2_value, NULL, 0, 0),
1240 SENSOR_ATTR_2(fan%d_alarm, 0444, show_bank2_alarm, NULL, 0, 0),
1241 SENSOR_ATTR_2(fan%d_min, 0644, show_bank2_setting,
1242 store_bank2_setting, 1, 0),
1243 SENSOR_ATTR_2(fan%d_beep, 0644, show_bank2_mask,
1244 store_bank2_mask, ABIT_UGURU_BEEP_ENABLE, 0),
1245 SENSOR_ATTR_2(fan%d_shutdown, 0644, show_bank2_mask,
1246 store_bank2_mask, ABIT_UGURU_SHUTDOWN_ENABLE, 0),
1247 SENSOR_ATTR_2(fan%d_alarm_enable, 0644, show_bank2_mask,
1248 store_bank2_mask, ABIT_UGURU_FAN_LOW_ALARM_ENABLE, 0),
1249};
1250
1251static const struct sensor_device_attribute_2 abituguru_sysfs_pwm_templ[6] = {
1252 SENSOR_ATTR_2(pwm%d_enable, 0644, show_pwm_enable,
1253 store_pwm_enable, 0, 0),
1254 SENSOR_ATTR_2(pwm%d_auto_channels_temp, 0644, show_pwm_sensor,
1255 store_pwm_sensor, 0, 0),
1256 SENSOR_ATTR_2(pwm%d_auto_point1_pwm, 0644, show_pwm_setting,
1257 store_pwm_setting, 1, 0),
1258 SENSOR_ATTR_2(pwm%d_auto_point2_pwm, 0644, show_pwm_setting,
1259 store_pwm_setting, 2, 0),
1260 SENSOR_ATTR_2(pwm%d_auto_point1_temp, 0644, show_pwm_setting,
1261 store_pwm_setting, 3, 0),
1262 SENSOR_ATTR_2(pwm%d_auto_point2_temp, 0644, show_pwm_setting,
1263 store_pwm_setting, 4, 0),
1264};
1265
1266static struct sensor_device_attribute_2 abituguru_sysfs_attr[] = {
1267 SENSOR_ATTR_2(name, 0444, show_name, NULL, 0, 0),
1268};
1269
1270static int abituguru_probe(struct platform_device *pdev)
1271{
1272 struct abituguru_data *data;
1273 int i, j, used, sysfs_names_free, sysfs_attr_i, res = -ENODEV;
1274 char *sysfs_filename;
1275
1276 /*
1277 * El weirdo probe order, to keep the sysfs order identical to the
1278 * BIOS and window-appliction listing order.
1279 */
1280 const u8 probe_order[ABIT_UGURU_MAX_BANK1_SENSORS] = {
1281 0x00, 0x01, 0x03, 0x04, 0x0A, 0x08, 0x0E, 0x02,
1282 0x09, 0x06, 0x05, 0x0B, 0x0F, 0x0D, 0x07, 0x0C };
1283
1284 data = devm_kzalloc(&pdev->dev, sizeof(struct abituguru_data),
1285 GFP_KERNEL);
1286 if (!data)
1287 return -ENOMEM;
1288
1289 data->addr = platform_get_resource(pdev, IORESOURCE_IO, 0)->start;
1290 mutex_init(&data->update_lock);
1291 platform_set_drvdata(pdev, data);
1292
1293 /* See if the uGuru is ready */
1294 if (inb_p(data->addr + ABIT_UGURU_DATA) == ABIT_UGURU_STATUS_INPUT)
1295 data->uguru_ready = 1;
1296
1297 /*
1298 * Completely read the uGuru this has 2 purposes:
1299 * - testread / see if one really is there.
1300 * - make an in memory copy of all the uguru settings for future use.
1301 */
1302 if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0,
1303 data->alarms, 3, ABIT_UGURU_MAX_RETRIES) != 3)
1304 goto abituguru_probe_error;
1305
1306 for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
1307 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1, i,
1308 &data->bank1_value[i], 1,
1309 ABIT_UGURU_MAX_RETRIES) != 1)
1310 goto abituguru_probe_error;
1311 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1+1, i,
1312 data->bank1_settings[i], 3,
1313 ABIT_UGURU_MAX_RETRIES) != 3)
1314 goto abituguru_probe_error;
1315 }
1316 /*
1317 * Note: We don't know how many bank2 sensors / pwms there really are,
1318 * but in order to "detect" this we need to read the maximum amount
1319 * anyways. If we read sensors/pwms not there we'll just read crap
1320 * this can't hurt. We need the detection because we don't want
1321 * unwanted writes, which will hurt!
1322 */
1323 for (i = 0; i < ABIT_UGURU_MAX_BANK2_SENSORS; i++) {
1324 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK2, i,
1325 &data->bank2_value[i], 1,
1326 ABIT_UGURU_MAX_RETRIES) != 1)
1327 goto abituguru_probe_error;
1328 if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK2+1, i,
1329 data->bank2_settings[i], 2,
1330 ABIT_UGURU_MAX_RETRIES) != 2)
1331 goto abituguru_probe_error;
1332 }
1333 for (i = 0; i < ABIT_UGURU_MAX_PWMS; i++) {
1334 if (abituguru_read(data, ABIT_UGURU_FAN_PWM, i,
1335 data->pwm_settings[i], 5,
1336 ABIT_UGURU_MAX_RETRIES) != 5)
1337 goto abituguru_probe_error;
1338 }
1339 data->last_updated = jiffies;
1340
1341 /* Detect sensor types and fill the sysfs attr for bank1 */
1342 sysfs_attr_i = 0;
1343 sysfs_filename = data->sysfs_names;
1344 sysfs_names_free = ABITUGURU_SYSFS_NAMES_LENGTH;
1345 for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
1346 res = abituguru_detect_bank1_sensor_type(data, probe_order[i]);
1347 if (res < 0)
1348 goto abituguru_probe_error;
1349 if (res == ABIT_UGURU_NC)
1350 continue;
1351
1352 /* res 1 (temp) sensors have 7 sysfs entries, 0 (in) 9 */
1353 for (j = 0; j < (res ? 7 : 9); j++) {
1354 used = snprintf(sysfs_filename, sysfs_names_free,
1355 abituguru_sysfs_bank1_templ[res][j].dev_attr.
1356 attr.name, data->bank1_sensors[res] + res)
1357 + 1;
1358 data->sysfs_attr[sysfs_attr_i] =
1359 abituguru_sysfs_bank1_templ[res][j];
1360 data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
1361 sysfs_filename;
1362 data->sysfs_attr[sysfs_attr_i].index = probe_order[i];
1363 sysfs_filename += used;
1364 sysfs_names_free -= used;
1365 sysfs_attr_i++;
1366 }
1367 data->bank1_max_value[probe_order[i]] =
1368 abituguru_bank1_max_value[res];
1369 data->bank1_address[res][data->bank1_sensors[res]] =
1370 probe_order[i];
1371 data->bank1_sensors[res]++;
1372 }
1373 /* Detect number of sensors and fill the sysfs attr for bank2 (fans) */
1374 abituguru_detect_no_bank2_sensors(data);
1375 for (i = 0; i < data->bank2_sensors; i++) {
1376 for (j = 0; j < ARRAY_SIZE(abituguru_sysfs_fan_templ); j++) {
1377 used = snprintf(sysfs_filename, sysfs_names_free,
1378 abituguru_sysfs_fan_templ[j].dev_attr.attr.name,
1379 i + 1) + 1;
1380 data->sysfs_attr[sysfs_attr_i] =
1381 abituguru_sysfs_fan_templ[j];
1382 data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
1383 sysfs_filename;
1384 data->sysfs_attr[sysfs_attr_i].index = i;
1385 sysfs_filename += used;
1386 sysfs_names_free -= used;
1387 sysfs_attr_i++;
1388 }
1389 }
1390 /* Detect number of sensors and fill the sysfs attr for pwms */
1391 abituguru_detect_no_pwms(data);
1392 for (i = 0; i < data->pwms; i++) {
1393 for (j = 0; j < ARRAY_SIZE(abituguru_sysfs_pwm_templ); j++) {
1394 used = snprintf(sysfs_filename, sysfs_names_free,
1395 abituguru_sysfs_pwm_templ[j].dev_attr.attr.name,
1396 i + 1) + 1;
1397 data->sysfs_attr[sysfs_attr_i] =
1398 abituguru_sysfs_pwm_templ[j];
1399 data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
1400 sysfs_filename;
1401 data->sysfs_attr[sysfs_attr_i].index = i;
1402 sysfs_filename += used;
1403 sysfs_names_free -= used;
1404 sysfs_attr_i++;
1405 }
1406 }
1407 /* Fail safe check, this should never happen! */
1408 if (sysfs_names_free < 0) {
1409 pr_err("Fatal error ran out of space for sysfs attr names. %s %s",
1410 never_happen, report_this);
1411 res = -ENAMETOOLONG;
1412 goto abituguru_probe_error;
1413 }
1414 pr_info("found Abit uGuru\n");
1415
1416 /* Register sysfs hooks */
1417 for (i = 0; i < sysfs_attr_i; i++) {
1418 res = device_create_file(&pdev->dev,
1419 &data->sysfs_attr[i].dev_attr);
1420 if (res)
1421 goto abituguru_probe_error;
1422 }
1423 for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++) {
1424 res = device_create_file(&pdev->dev,
1425 &abituguru_sysfs_attr[i].dev_attr);
1426 if (res)
1427 goto abituguru_probe_error;
1428 }
1429
1430 data->hwmon_dev = hwmon_device_register(&pdev->dev);
1431 if (!IS_ERR(data->hwmon_dev))
1432 return 0; /* success */
1433
1434 res = PTR_ERR(data->hwmon_dev);
1435abituguru_probe_error:
1436 for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++)
1437 device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
1438 for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++)
1439 device_remove_file(&pdev->dev,
1440 &abituguru_sysfs_attr[i].dev_attr);
1441 return res;
1442}
1443
1444static int abituguru_remove(struct platform_device *pdev)
1445{
1446 int i;
1447 struct abituguru_data *data = platform_get_drvdata(pdev);
1448
1449 hwmon_device_unregister(data->hwmon_dev);
1450 for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++)
1451 device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
1452 for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++)
1453 device_remove_file(&pdev->dev,
1454 &abituguru_sysfs_attr[i].dev_attr);
1455
1456 return 0;
1457}
1458
1459static struct abituguru_data *abituguru_update_device(struct device *dev)
1460{
1461 int i, err;
1462 struct abituguru_data *data = dev_get_drvdata(dev);
1463 /* fake a complete successful read if no update necessary. */
1464 char success = 1;
1465
1466 mutex_lock(&data->update_lock);
1467 if (time_after(jiffies, data->last_updated + HZ)) {
1468 success = 0;
1469 err = abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0,
1470 data->alarms, 3, 0);
1471 if (err != 3)
1472 goto LEAVE_UPDATE;
1473 for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
1474 err = abituguru_read(data, ABIT_UGURU_SENSOR_BANK1,
1475 i, &data->bank1_value[i], 1, 0);
1476 if (err != 1)
1477 goto LEAVE_UPDATE;
1478 err = abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1,
1479 i, data->bank1_settings[i], 3, 0);
1480 if (err != 3)
1481 goto LEAVE_UPDATE;
1482 }
1483 for (i = 0; i < data->bank2_sensors; i++) {
1484 err = abituguru_read(data, ABIT_UGURU_SENSOR_BANK2, i,
1485 &data->bank2_value[i], 1, 0);
1486 if (err != 1)
1487 goto LEAVE_UPDATE;
1488 }
1489 /* success! */
1490 success = 1;
1491 data->update_timeouts = 0;
1492LEAVE_UPDATE:
1493 /* handle timeout condition */
1494 if (!success && (err == -EBUSY || err >= 0)) {
1495 /* No overflow please */
1496 if (data->update_timeouts < 255u)
1497 data->update_timeouts++;
1498 if (data->update_timeouts <= ABIT_UGURU_MAX_TIMEOUTS) {
1499 ABIT_UGURU_DEBUG(3, "timeout exceeded, will "
1500 "try again next update\n");
1501 /* Just a timeout, fake a successful read */
1502 success = 1;
1503 } else
1504 ABIT_UGURU_DEBUG(1, "timeout exceeded %d "
1505 "times waiting for more input state\n",
1506 (int)data->update_timeouts);
1507 }
1508 /* On success set last_updated */
1509 if (success)
1510 data->last_updated = jiffies;
1511 }
1512 mutex_unlock(&data->update_lock);
1513
1514 if (success)
1515 return data;
1516 else
1517 return NULL;
1518}
1519
1520#ifdef CONFIG_PM_SLEEP
1521static int abituguru_suspend(struct device *dev)
1522{
1523 struct abituguru_data *data = dev_get_drvdata(dev);
1524 /*
1525 * make sure all communications with the uguru are done and no new
1526 * ones are started
1527 */
1528 mutex_lock(&data->update_lock);
1529 return 0;
1530}
1531
1532static int abituguru_resume(struct device *dev)
1533{
1534 struct abituguru_data *data = dev_get_drvdata(dev);
1535 /* See if the uGuru is still ready */
1536 if (inb_p(data->addr + ABIT_UGURU_DATA) != ABIT_UGURU_STATUS_INPUT)
1537 data->uguru_ready = 0;
1538 mutex_unlock(&data->update_lock);
1539 return 0;
1540}
1541
1542static SIMPLE_DEV_PM_OPS(abituguru_pm, abituguru_suspend, abituguru_resume);
1543#define ABIT_UGURU_PM (&abituguru_pm)
1544#else
1545#define ABIT_UGURU_PM NULL
1546#endif /* CONFIG_PM */
1547
1548static struct platform_driver abituguru_driver = {
1549 .driver = {
1550 .name = ABIT_UGURU_NAME,
1551 .pm = ABIT_UGURU_PM,
1552 },
1553 .probe = abituguru_probe,
1554 .remove = abituguru_remove,
1555};
1556
1557static int __init abituguru_detect(void)
1558{
1559 /*
1560 * See if there is an uguru there. After a reboot uGuru will hold 0x00
1561 * at DATA and 0xAC, when this driver has already been loaded once
1562 * DATA will hold 0x08. For most uGuru's CMD will hold 0xAC in either
1563 * scenario but some will hold 0x00.
1564 * Some uGuru's initially hold 0x09 at DATA and will only hold 0x08
1565 * after reading CMD first, so CMD must be read first!
1566 */
1567 u8 cmd_val = inb_p(ABIT_UGURU_BASE + ABIT_UGURU_CMD);
1568 u8 data_val = inb_p(ABIT_UGURU_BASE + ABIT_UGURU_DATA);
1569 if (((data_val == 0x00) || (data_val == 0x08)) &&
1570 ((cmd_val == 0x00) || (cmd_val == 0xAC)))
1571 return ABIT_UGURU_BASE;
1572
1573 ABIT_UGURU_DEBUG(2, "no Abit uGuru found, data = 0x%02X, cmd = "
1574 "0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val);
1575
1576 if (force) {
1577 pr_info("Assuming Abit uGuru is present because of \"force\" parameter\n");
1578 return ABIT_UGURU_BASE;
1579 }
1580
1581 /* No uGuru found */
1582 return -ENODEV;
1583}
1584
1585static struct platform_device *abituguru_pdev;
1586
1587static int __init abituguru_init(void)
1588{
1589 int address, err;
1590 struct resource res = { .flags = IORESOURCE_IO };
1591 const char *board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR);
1592
1593 /* safety check, refuse to load on non Abit motherboards */
1594 if (!force && (!board_vendor ||
1595 strcmp(board_vendor, "http://www.abit.com.tw/")))
1596 return -ENODEV;
1597
1598 address = abituguru_detect();
1599 if (address < 0)
1600 return address;
1601
1602 err = platform_driver_register(&abituguru_driver);
1603 if (err)
1604 goto exit;
1605
1606 abituguru_pdev = platform_device_alloc(ABIT_UGURU_NAME, address);
1607 if (!abituguru_pdev) {
1608 pr_err("Device allocation failed\n");
1609 err = -ENOMEM;
1610 goto exit_driver_unregister;
1611 }
1612
1613 res.start = address;
1614 res.end = address + ABIT_UGURU_REGION_LENGTH - 1;
1615 res.name = ABIT_UGURU_NAME;
1616
1617 err = platform_device_add_resources(abituguru_pdev, &res, 1);
1618 if (err) {
1619 pr_err("Device resource addition failed (%d)\n", err);
1620 goto exit_device_put;
1621 }
1622
1623 err = platform_device_add(abituguru_pdev);
1624 if (err) {
1625 pr_err("Device addition failed (%d)\n", err);
1626 goto exit_device_put;
1627 }
1628
1629 return 0;
1630
1631exit_device_put:
1632 platform_device_put(abituguru_pdev);
1633exit_driver_unregister:
1634 platform_driver_unregister(&abituguru_driver);
1635exit:
1636 return err;
1637}
1638
1639static void __exit abituguru_exit(void)
1640{
1641 platform_device_unregister(abituguru_pdev);
1642 platform_driver_unregister(&abituguru_driver);
1643}
1644
1645MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
1646MODULE_DESCRIPTION("Abit uGuru Sensor device");
1647MODULE_LICENSE("GPL");
1648
1649module_init(abituguru_init);
1650module_exit(abituguru_exit);