Loading...
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * st-asc.c: ST Asynchronous serial controller (ASC) driver
4 *
5 * Copyright (C) 2003-2013 STMicroelectronics (R&D) Limited
6 */
7
8#include <linux/module.h>
9#include <linux/serial.h>
10#include <linux/console.h>
11#include <linux/sysrq.h>
12#include <linux/pinctrl/consumer.h>
13#include <linux/platform_device.h>
14#include <linux/io.h>
15#include <linux/irq.h>
16#include <linux/tty.h>
17#include <linux/tty_flip.h>
18#include <linux/delay.h>
19#include <linux/spinlock.h>
20#include <linux/of.h>
21#include <linux/of_platform.h>
22#include <linux/serial_core.h>
23#include <linux/clk.h>
24#include <linux/gpio/consumer.h>
25
26#define DRIVER_NAME "st-asc"
27#define ASC_SERIAL_NAME "ttyAS"
28#define ASC_FIFO_SIZE 16
29#define ASC_MAX_PORTS 8
30
31/* Pinctrl states */
32#define DEFAULT 0
33#define NO_HW_FLOWCTRL 1
34
35struct asc_port {
36 struct uart_port port;
37 struct gpio_desc *rts;
38 struct clk *clk;
39 struct pinctrl *pinctrl;
40 struct pinctrl_state *states[2];
41 unsigned int hw_flow_control:1;
42 unsigned int force_m1:1;
43};
44
45static struct asc_port asc_ports[ASC_MAX_PORTS];
46static struct uart_driver asc_uart_driver;
47
48/*---- UART Register definitions ------------------------------*/
49
50/* Register offsets */
51
52#define ASC_BAUDRATE 0x00
53#define ASC_TXBUF 0x04
54#define ASC_RXBUF 0x08
55#define ASC_CTL 0x0C
56#define ASC_INTEN 0x10
57#define ASC_STA 0x14
58#define ASC_GUARDTIME 0x18
59#define ASC_TIMEOUT 0x1C
60#define ASC_TXRESET 0x20
61#define ASC_RXRESET 0x24
62#define ASC_RETRIES 0x28
63
64/* ASC_RXBUF */
65#define ASC_RXBUF_PE 0x100
66#define ASC_RXBUF_FE 0x200
67/*
68 * Some of status comes from higher bits of the character and some come from
69 * the status register. Combining both of them in to single status using dummy
70 * bits.
71 */
72#define ASC_RXBUF_DUMMY_RX 0x10000
73#define ASC_RXBUF_DUMMY_BE 0x20000
74#define ASC_RXBUF_DUMMY_OE 0x40000
75
76/* ASC_CTL */
77
78#define ASC_CTL_MODE_MSK 0x0007
79#define ASC_CTL_MODE_8BIT 0x0001
80#define ASC_CTL_MODE_7BIT_PAR 0x0003
81#define ASC_CTL_MODE_9BIT 0x0004
82#define ASC_CTL_MODE_8BIT_WKUP 0x0005
83#define ASC_CTL_MODE_8BIT_PAR 0x0007
84#define ASC_CTL_STOP_MSK 0x0018
85#define ASC_CTL_STOP_HALFBIT 0x0000
86#define ASC_CTL_STOP_1BIT 0x0008
87#define ASC_CTL_STOP_1_HALFBIT 0x0010
88#define ASC_CTL_STOP_2BIT 0x0018
89#define ASC_CTL_PARITYODD 0x0020
90#define ASC_CTL_LOOPBACK 0x0040
91#define ASC_CTL_RUN 0x0080
92#define ASC_CTL_RXENABLE 0x0100
93#define ASC_CTL_SCENABLE 0x0200
94#define ASC_CTL_FIFOENABLE 0x0400
95#define ASC_CTL_CTSENABLE 0x0800
96#define ASC_CTL_BAUDMODE 0x1000
97
98/* ASC_GUARDTIME */
99
100#define ASC_GUARDTIME_MSK 0x00FF
101
102/* ASC_INTEN */
103
104#define ASC_INTEN_RBE 0x0001
105#define ASC_INTEN_TE 0x0002
106#define ASC_INTEN_THE 0x0004
107#define ASC_INTEN_PE 0x0008
108#define ASC_INTEN_FE 0x0010
109#define ASC_INTEN_OE 0x0020
110#define ASC_INTEN_TNE 0x0040
111#define ASC_INTEN_TOI 0x0080
112#define ASC_INTEN_RHF 0x0100
113
114/* ASC_RETRIES */
115
116#define ASC_RETRIES_MSK 0x00FF
117
118/* ASC_RXBUF */
119
120#define ASC_RXBUF_MSK 0x03FF
121
122/* ASC_STA */
123
124#define ASC_STA_RBF 0x0001
125#define ASC_STA_TE 0x0002
126#define ASC_STA_THE 0x0004
127#define ASC_STA_PE 0x0008
128#define ASC_STA_FE 0x0010
129#define ASC_STA_OE 0x0020
130#define ASC_STA_TNE 0x0040
131#define ASC_STA_TOI 0x0080
132#define ASC_STA_RHF 0x0100
133#define ASC_STA_TF 0x0200
134#define ASC_STA_NKD 0x0400
135
136/* ASC_TIMEOUT */
137
138#define ASC_TIMEOUT_MSK 0x00FF
139
140/* ASC_TXBUF */
141
142#define ASC_TXBUF_MSK 0x01FF
143
144/*---- Inline function definitions ---------------------------*/
145
146static inline struct asc_port *to_asc_port(struct uart_port *port)
147{
148 return container_of(port, struct asc_port, port);
149}
150
151static inline u32 asc_in(struct uart_port *port, u32 offset)
152{
153#ifdef readl_relaxed
154 return readl_relaxed(port->membase + offset);
155#else
156 return readl(port->membase + offset);
157#endif
158}
159
160static inline void asc_out(struct uart_port *port, u32 offset, u32 value)
161{
162#ifdef writel_relaxed
163 writel_relaxed(value, port->membase + offset);
164#else
165 writel(value, port->membase + offset);
166#endif
167}
168
169/*
170 * Some simple utility functions to enable and disable interrupts.
171 * Note that these need to be called with interrupts disabled.
172 */
173static inline void asc_disable_tx_interrupts(struct uart_port *port)
174{
175 u32 intenable = asc_in(port, ASC_INTEN) & ~ASC_INTEN_THE;
176 asc_out(port, ASC_INTEN, intenable);
177 (void)asc_in(port, ASC_INTEN); /* Defeat bus write posting */
178}
179
180static inline void asc_enable_tx_interrupts(struct uart_port *port)
181{
182 u32 intenable = asc_in(port, ASC_INTEN) | ASC_INTEN_THE;
183 asc_out(port, ASC_INTEN, intenable);
184}
185
186static inline void asc_disable_rx_interrupts(struct uart_port *port)
187{
188 u32 intenable = asc_in(port, ASC_INTEN) & ~ASC_INTEN_RBE;
189 asc_out(port, ASC_INTEN, intenable);
190 (void)asc_in(port, ASC_INTEN); /* Defeat bus write posting */
191}
192
193static inline void asc_enable_rx_interrupts(struct uart_port *port)
194{
195 u32 intenable = asc_in(port, ASC_INTEN) | ASC_INTEN_RBE;
196 asc_out(port, ASC_INTEN, intenable);
197}
198
199static inline u32 asc_txfifo_is_empty(struct uart_port *port)
200{
201 return asc_in(port, ASC_STA) & ASC_STA_TE;
202}
203
204static inline u32 asc_txfifo_is_half_empty(struct uart_port *port)
205{
206 return asc_in(port, ASC_STA) & ASC_STA_THE;
207}
208
209static inline const char *asc_port_name(struct uart_port *port)
210{
211 return to_platform_device(port->dev)->name;
212}
213
214/*----------------------------------------------------------------------*/
215
216/*
217 * This section contains code to support the use of the ASC as a
218 * generic serial port.
219 */
220
221static inline unsigned asc_hw_txroom(struct uart_port *port)
222{
223 u32 status = asc_in(port, ASC_STA);
224
225 if (status & ASC_STA_THE)
226 return port->fifosize / 2;
227 else if (!(status & ASC_STA_TF))
228 return 1;
229
230 return 0;
231}
232
233/*
234 * Start transmitting chars.
235 * This is called from both interrupt and task level.
236 * Either way interrupts are disabled.
237 */
238static void asc_transmit_chars(struct uart_port *port)
239{
240 u8 ch;
241
242 uart_port_tx_limited(port, ch, asc_hw_txroom(port),
243 true,
244 asc_out(port, ASC_TXBUF, ch),
245 ({}));
246}
247
248static void asc_receive_chars(struct uart_port *port)
249{
250 struct tty_port *tport = &port->state->port;
251 unsigned long status, mode;
252 unsigned long c = 0;
253 u8 flag;
254 bool ignore_pe = false;
255
256 /*
257 * Datasheet states: If the MODE field selects an 8-bit frame then
258 * this [parity error] bit is undefined. Software should ignore this
259 * bit when reading 8-bit frames.
260 */
261 mode = asc_in(port, ASC_CTL) & ASC_CTL_MODE_MSK;
262 if (mode == ASC_CTL_MODE_8BIT || mode == ASC_CTL_MODE_8BIT_PAR)
263 ignore_pe = true;
264
265 if (irqd_is_wakeup_set(irq_get_irq_data(port->irq)))
266 pm_wakeup_event(tport->tty->dev, 0);
267
268 while ((status = asc_in(port, ASC_STA)) & ASC_STA_RBF) {
269 c = asc_in(port, ASC_RXBUF) | ASC_RXBUF_DUMMY_RX;
270 flag = TTY_NORMAL;
271 port->icount.rx++;
272
273 if (status & ASC_STA_OE || c & ASC_RXBUF_FE ||
274 (c & ASC_RXBUF_PE && !ignore_pe)) {
275
276 if (c & ASC_RXBUF_FE) {
277 if (c == (ASC_RXBUF_FE | ASC_RXBUF_DUMMY_RX)) {
278 port->icount.brk++;
279 if (uart_handle_break(port))
280 continue;
281 c |= ASC_RXBUF_DUMMY_BE;
282 } else {
283 port->icount.frame++;
284 }
285 } else if (c & ASC_RXBUF_PE) {
286 port->icount.parity++;
287 }
288 /*
289 * Reading any data from the RX FIFO clears the
290 * overflow error condition.
291 */
292 if (status & ASC_STA_OE) {
293 port->icount.overrun++;
294 c |= ASC_RXBUF_DUMMY_OE;
295 }
296
297 c &= port->read_status_mask;
298
299 if (c & ASC_RXBUF_DUMMY_BE)
300 flag = TTY_BREAK;
301 else if (c & ASC_RXBUF_PE)
302 flag = TTY_PARITY;
303 else if (c & ASC_RXBUF_FE)
304 flag = TTY_FRAME;
305 }
306
307 if (uart_handle_sysrq_char(port, c & 0xff))
308 continue;
309
310 uart_insert_char(port, c, ASC_RXBUF_DUMMY_OE, c & 0xff, flag);
311 }
312
313 /* Tell the rest of the system the news. New characters! */
314 tty_flip_buffer_push(tport);
315}
316
317static irqreturn_t asc_interrupt(int irq, void *ptr)
318{
319 struct uart_port *port = ptr;
320 u32 status;
321
322 uart_port_lock(port);
323
324 status = asc_in(port, ASC_STA);
325
326 if (status & ASC_STA_RBF) {
327 /* Receive FIFO not empty */
328 asc_receive_chars(port);
329 }
330
331 if ((status & ASC_STA_THE) &&
332 (asc_in(port, ASC_INTEN) & ASC_INTEN_THE)) {
333 /* Transmitter FIFO at least half empty */
334 asc_transmit_chars(port);
335 }
336
337 uart_port_unlock(port);
338
339 return IRQ_HANDLED;
340}
341
342/*----------------------------------------------------------------------*/
343
344/*
345 * UART Functions
346 */
347
348static unsigned int asc_tx_empty(struct uart_port *port)
349{
350 return asc_txfifo_is_empty(port) ? TIOCSER_TEMT : 0;
351}
352
353static void asc_set_mctrl(struct uart_port *port, unsigned int mctrl)
354{
355 struct asc_port *ascport = to_asc_port(port);
356
357 /*
358 * This routine is used for seting signals of: DTR, DCD, CTS and RTS.
359 * We use ASC's hardware for CTS/RTS when hardware flow-control is
360 * enabled, however if the RTS line is required for another purpose,
361 * commonly controlled using HUP from userspace, then we need to toggle
362 * it manually, using GPIO.
363 *
364 * Some boards also have DTR and DCD implemented using PIO pins, code to
365 * do this should be hooked in here.
366 */
367
368 if (!ascport->rts)
369 return;
370
371 /* If HW flow-control is enabled, we can't fiddle with the RTS line */
372 if (asc_in(port, ASC_CTL) & ASC_CTL_CTSENABLE)
373 return;
374
375 gpiod_set_value(ascport->rts, mctrl & TIOCM_RTS);
376}
377
378static unsigned int asc_get_mctrl(struct uart_port *port)
379{
380 /*
381 * This routine is used for geting signals of: DTR, DCD, DSR, RI,
382 * and CTS/RTS
383 */
384 return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
385}
386
387/* There are probably characters waiting to be transmitted. */
388static void asc_start_tx(struct uart_port *port)
389{
390 struct circ_buf *xmit = &port->state->xmit;
391
392 if (!uart_circ_empty(xmit))
393 asc_enable_tx_interrupts(port);
394}
395
396/* Transmit stop */
397static void asc_stop_tx(struct uart_port *port)
398{
399 asc_disable_tx_interrupts(port);
400}
401
402/* Receive stop */
403static void asc_stop_rx(struct uart_port *port)
404{
405 asc_disable_rx_interrupts(port);
406}
407
408/* Handle breaks - ignored by us */
409static void asc_break_ctl(struct uart_port *port, int break_state)
410{
411 /* Nothing here yet .. */
412}
413
414/*
415 * Enable port for reception.
416 */
417static int asc_startup(struct uart_port *port)
418{
419 if (request_irq(port->irq, asc_interrupt, 0,
420 asc_port_name(port), port)) {
421 dev_err(port->dev, "cannot allocate irq.\n");
422 return -ENODEV;
423 }
424
425 asc_transmit_chars(port);
426 asc_enable_rx_interrupts(port);
427
428 return 0;
429}
430
431static void asc_shutdown(struct uart_port *port)
432{
433 asc_disable_tx_interrupts(port);
434 asc_disable_rx_interrupts(port);
435 free_irq(port->irq, port);
436}
437
438static void asc_pm(struct uart_port *port, unsigned int state,
439 unsigned int oldstate)
440{
441 struct asc_port *ascport = to_asc_port(port);
442 unsigned long flags;
443 u32 ctl;
444
445 switch (state) {
446 case UART_PM_STATE_ON:
447 clk_prepare_enable(ascport->clk);
448 break;
449 case UART_PM_STATE_OFF:
450 /*
451 * Disable the ASC baud rate generator, which is as close as
452 * we can come to turning it off. Note this is not called with
453 * the port spinlock held.
454 */
455 uart_port_lock_irqsave(port, &flags);
456 ctl = asc_in(port, ASC_CTL) & ~ASC_CTL_RUN;
457 asc_out(port, ASC_CTL, ctl);
458 uart_port_unlock_irqrestore(port, flags);
459 clk_disable_unprepare(ascport->clk);
460 break;
461 }
462}
463
464static void asc_set_termios(struct uart_port *port, struct ktermios *termios,
465 const struct ktermios *old)
466{
467 struct asc_port *ascport = to_asc_port(port);
468 struct gpio_desc *gpiod;
469 unsigned int baud;
470 u32 ctrl_val;
471 tcflag_t cflag;
472 unsigned long flags;
473
474 /* Update termios to reflect hardware capabilities */
475 termios->c_cflag &= ~(CMSPAR |
476 (ascport->hw_flow_control ? 0 : CRTSCTS));
477
478 port->uartclk = clk_get_rate(ascport->clk);
479
480 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
481 cflag = termios->c_cflag;
482
483 uart_port_lock_irqsave(port, &flags);
484
485 /* read control register */
486 ctrl_val = asc_in(port, ASC_CTL);
487
488 /* stop serial port and reset value */
489 asc_out(port, ASC_CTL, (ctrl_val & ~ASC_CTL_RUN));
490 ctrl_val = ASC_CTL_RXENABLE | ASC_CTL_FIFOENABLE;
491
492 /* reset fifo rx & tx */
493 asc_out(port, ASC_TXRESET, 1);
494 asc_out(port, ASC_RXRESET, 1);
495
496 /* set character length */
497 if ((cflag & CSIZE) == CS7) {
498 ctrl_val |= ASC_CTL_MODE_7BIT_PAR;
499 cflag |= PARENB;
500 } else {
501 ctrl_val |= (cflag & PARENB) ? ASC_CTL_MODE_8BIT_PAR :
502 ASC_CTL_MODE_8BIT;
503 cflag &= ~CSIZE;
504 cflag |= CS8;
505 }
506 termios->c_cflag = cflag;
507
508 /* set stop bit */
509 ctrl_val |= (cflag & CSTOPB) ? ASC_CTL_STOP_2BIT : ASC_CTL_STOP_1BIT;
510
511 /* odd parity */
512 if (cflag & PARODD)
513 ctrl_val |= ASC_CTL_PARITYODD;
514
515 /* hardware flow control */
516 if ((cflag & CRTSCTS)) {
517 ctrl_val |= ASC_CTL_CTSENABLE;
518
519 /* If flow-control selected, stop handling RTS manually */
520 if (ascport->rts) {
521 devm_gpiod_put(port->dev, ascport->rts);
522 ascport->rts = NULL;
523
524 pinctrl_select_state(ascport->pinctrl,
525 ascport->states[DEFAULT]);
526 }
527 } else {
528 /* If flow-control disabled, it's safe to handle RTS manually */
529 if (!ascport->rts && ascport->states[NO_HW_FLOWCTRL]) {
530 pinctrl_select_state(ascport->pinctrl,
531 ascport->states[NO_HW_FLOWCTRL]);
532
533 gpiod = devm_gpiod_get(port->dev, "rts", GPIOD_OUT_LOW);
534 if (!IS_ERR(gpiod)) {
535 gpiod_set_consumer_name(gpiod,
536 port->dev->of_node->name);
537 ascport->rts = gpiod;
538 }
539 }
540 }
541
542 if ((baud < 19200) && !ascport->force_m1) {
543 asc_out(port, ASC_BAUDRATE, (port->uartclk / (16 * baud)));
544 } else {
545 /*
546 * MODE 1: recommended for high bit rates (above 19.2K)
547 *
548 * baudrate * 16 * 2^16
549 * ASCBaudRate = ------------------------
550 * inputclock
551 *
552 * To keep maths inside 64bits, we divide inputclock by 16.
553 */
554 u64 dividend = (u64)baud * (1 << 16);
555
556 do_div(dividend, port->uartclk / 16);
557 asc_out(port, ASC_BAUDRATE, dividend);
558 ctrl_val |= ASC_CTL_BAUDMODE;
559 }
560
561 uart_update_timeout(port, cflag, baud);
562
563 ascport->port.read_status_mask = ASC_RXBUF_DUMMY_OE;
564 if (termios->c_iflag & INPCK)
565 ascport->port.read_status_mask |= ASC_RXBUF_FE | ASC_RXBUF_PE;
566 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
567 ascport->port.read_status_mask |= ASC_RXBUF_DUMMY_BE;
568
569 /*
570 * Characters to ignore
571 */
572 ascport->port.ignore_status_mask = 0;
573 if (termios->c_iflag & IGNPAR)
574 ascport->port.ignore_status_mask |= ASC_RXBUF_FE | ASC_RXBUF_PE;
575 if (termios->c_iflag & IGNBRK) {
576 ascport->port.ignore_status_mask |= ASC_RXBUF_DUMMY_BE;
577 /*
578 * If we're ignoring parity and break indicators,
579 * ignore overruns too (for real raw support).
580 */
581 if (termios->c_iflag & IGNPAR)
582 ascport->port.ignore_status_mask |= ASC_RXBUF_DUMMY_OE;
583 }
584
585 /*
586 * Ignore all characters if CREAD is not set.
587 */
588 if (!(termios->c_cflag & CREAD))
589 ascport->port.ignore_status_mask |= ASC_RXBUF_DUMMY_RX;
590
591 /* Set the timeout */
592 asc_out(port, ASC_TIMEOUT, 20);
593
594 /* write final value and enable port */
595 asc_out(port, ASC_CTL, (ctrl_val | ASC_CTL_RUN));
596
597 uart_port_unlock_irqrestore(port, flags);
598}
599
600static const char *asc_type(struct uart_port *port)
601{
602 return (port->type == PORT_ASC) ? DRIVER_NAME : NULL;
603}
604
605static void asc_release_port(struct uart_port *port)
606{
607}
608
609static int asc_request_port(struct uart_port *port)
610{
611 return 0;
612}
613
614/*
615 * Called when the port is opened, and UPF_BOOT_AUTOCONF flag is set
616 * Set type field if successful
617 */
618static void asc_config_port(struct uart_port *port, int flags)
619{
620 if ((flags & UART_CONFIG_TYPE))
621 port->type = PORT_ASC;
622}
623
624static int
625asc_verify_port(struct uart_port *port, struct serial_struct *ser)
626{
627 /* No user changeable parameters */
628 return -EINVAL;
629}
630
631#ifdef CONFIG_CONSOLE_POLL
632/*
633 * Console polling routines for writing and reading from the uart while
634 * in an interrupt or debug context (i.e. kgdb).
635 */
636
637static int asc_get_poll_char(struct uart_port *port)
638{
639 if (!(asc_in(port, ASC_STA) & ASC_STA_RBF))
640 return NO_POLL_CHAR;
641
642 return asc_in(port, ASC_RXBUF);
643}
644
645static void asc_put_poll_char(struct uart_port *port, unsigned char c)
646{
647 while (!asc_txfifo_is_half_empty(port))
648 cpu_relax();
649 asc_out(port, ASC_TXBUF, c);
650}
651
652#endif /* CONFIG_CONSOLE_POLL */
653
654/*---------------------------------------------------------------------*/
655
656static const struct uart_ops asc_uart_ops = {
657 .tx_empty = asc_tx_empty,
658 .set_mctrl = asc_set_mctrl,
659 .get_mctrl = asc_get_mctrl,
660 .start_tx = asc_start_tx,
661 .stop_tx = asc_stop_tx,
662 .stop_rx = asc_stop_rx,
663 .break_ctl = asc_break_ctl,
664 .startup = asc_startup,
665 .shutdown = asc_shutdown,
666 .set_termios = asc_set_termios,
667 .type = asc_type,
668 .release_port = asc_release_port,
669 .request_port = asc_request_port,
670 .config_port = asc_config_port,
671 .verify_port = asc_verify_port,
672 .pm = asc_pm,
673#ifdef CONFIG_CONSOLE_POLL
674 .poll_get_char = asc_get_poll_char,
675 .poll_put_char = asc_put_poll_char,
676#endif /* CONFIG_CONSOLE_POLL */
677};
678
679static int asc_init_port(struct asc_port *ascport,
680 struct platform_device *pdev)
681{
682 struct uart_port *port = &ascport->port;
683 struct resource *res;
684 int ret;
685
686 port->iotype = UPIO_MEM;
687 port->flags = UPF_BOOT_AUTOCONF;
688 port->ops = &asc_uart_ops;
689 port->fifosize = ASC_FIFO_SIZE;
690 port->dev = &pdev->dev;
691 port->irq = platform_get_irq(pdev, 0);
692 port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_ST_ASC_CONSOLE);
693
694 port->membase = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
695 if (IS_ERR(port->membase))
696 return PTR_ERR(port->membase);
697 port->mapbase = res->start;
698
699 spin_lock_init(&port->lock);
700
701 ascport->clk = devm_clk_get(&pdev->dev, NULL);
702
703 if (WARN_ON(IS_ERR(ascport->clk)))
704 return -EINVAL;
705 /* ensure that clk rate is correct by enabling the clk */
706 ret = clk_prepare_enable(ascport->clk);
707 if (ret)
708 return ret;
709 ascport->port.uartclk = clk_get_rate(ascport->clk);
710 WARN_ON(ascport->port.uartclk == 0);
711 clk_disable_unprepare(ascport->clk);
712
713 ascport->pinctrl = devm_pinctrl_get(&pdev->dev);
714 if (IS_ERR(ascport->pinctrl)) {
715 ret = PTR_ERR(ascport->pinctrl);
716 dev_err(&pdev->dev, "Failed to get Pinctrl: %d\n", ret);
717 return ret;
718 }
719
720 ascport->states[DEFAULT] =
721 pinctrl_lookup_state(ascport->pinctrl, "default");
722 if (IS_ERR(ascport->states[DEFAULT])) {
723 ret = PTR_ERR(ascport->states[DEFAULT]);
724 dev_err(&pdev->dev,
725 "Failed to look up Pinctrl state 'default': %d\n", ret);
726 return ret;
727 }
728
729 /* "no-hw-flowctrl" state is optional */
730 ascport->states[NO_HW_FLOWCTRL] =
731 pinctrl_lookup_state(ascport->pinctrl, "no-hw-flowctrl");
732 if (IS_ERR(ascport->states[NO_HW_FLOWCTRL]))
733 ascport->states[NO_HW_FLOWCTRL] = NULL;
734
735 return 0;
736}
737
738static struct asc_port *asc_of_get_asc_port(struct platform_device *pdev)
739{
740 struct device_node *np = pdev->dev.of_node;
741 int id;
742
743 if (!np)
744 return NULL;
745
746 id = of_alias_get_id(np, "serial");
747 if (id < 0)
748 id = of_alias_get_id(np, ASC_SERIAL_NAME);
749
750 if (id < 0)
751 id = 0;
752
753 if (WARN_ON(id >= ASC_MAX_PORTS))
754 return NULL;
755
756 asc_ports[id].hw_flow_control = of_property_read_bool(np,
757 "uart-has-rtscts");
758 asc_ports[id].force_m1 = of_property_read_bool(np, "st,force-m1");
759 asc_ports[id].port.line = id;
760 asc_ports[id].rts = NULL;
761
762 return &asc_ports[id];
763}
764
765#ifdef CONFIG_OF
766static const struct of_device_id asc_match[] = {
767 { .compatible = "st,asc", },
768 {},
769};
770
771MODULE_DEVICE_TABLE(of, asc_match);
772#endif
773
774static int asc_serial_probe(struct platform_device *pdev)
775{
776 int ret;
777 struct asc_port *ascport;
778
779 ascport = asc_of_get_asc_port(pdev);
780 if (!ascport)
781 return -ENODEV;
782
783 ret = asc_init_port(ascport, pdev);
784 if (ret)
785 return ret;
786
787 ret = uart_add_one_port(&asc_uart_driver, &ascport->port);
788 if (ret)
789 return ret;
790
791 platform_set_drvdata(pdev, &ascport->port);
792
793 return 0;
794}
795
796static void asc_serial_remove(struct platform_device *pdev)
797{
798 struct uart_port *port = platform_get_drvdata(pdev);
799
800 uart_remove_one_port(&asc_uart_driver, port);
801}
802
803#ifdef CONFIG_PM_SLEEP
804static int asc_serial_suspend(struct device *dev)
805{
806 struct uart_port *port = dev_get_drvdata(dev);
807
808 return uart_suspend_port(&asc_uart_driver, port);
809}
810
811static int asc_serial_resume(struct device *dev)
812{
813 struct uart_port *port = dev_get_drvdata(dev);
814
815 return uart_resume_port(&asc_uart_driver, port);
816}
817
818#endif /* CONFIG_PM_SLEEP */
819
820/*----------------------------------------------------------------------*/
821
822#ifdef CONFIG_SERIAL_ST_ASC_CONSOLE
823static void asc_console_putchar(struct uart_port *port, unsigned char ch)
824{
825 unsigned int timeout = 1000000;
826
827 /* Wait for upto 1 second in case flow control is stopping us. */
828 while (--timeout && !asc_txfifo_is_half_empty(port))
829 udelay(1);
830
831 asc_out(port, ASC_TXBUF, ch);
832}
833
834/*
835 * Print a string to the serial port trying not to disturb
836 * any possible real use of the port...
837 */
838
839static void asc_console_write(struct console *co, const char *s, unsigned count)
840{
841 struct uart_port *port = &asc_ports[co->index].port;
842 unsigned long flags;
843 unsigned long timeout = 1000000;
844 int locked = 1;
845 u32 intenable;
846
847 if (port->sysrq)
848 locked = 0; /* asc_interrupt has already claimed the lock */
849 else if (oops_in_progress)
850 locked = uart_port_trylock_irqsave(port, &flags);
851 else
852 uart_port_lock_irqsave(port, &flags);
853
854 /*
855 * Disable interrupts so we don't get the IRQ line bouncing
856 * up and down while interrupts are disabled.
857 */
858 intenable = asc_in(port, ASC_INTEN);
859 asc_out(port, ASC_INTEN, 0);
860 (void)asc_in(port, ASC_INTEN); /* Defeat bus write posting */
861
862 uart_console_write(port, s, count, asc_console_putchar);
863
864 while (--timeout && !asc_txfifo_is_empty(port))
865 udelay(1);
866
867 asc_out(port, ASC_INTEN, intenable);
868
869 if (locked)
870 uart_port_unlock_irqrestore(port, flags);
871}
872
873static int asc_console_setup(struct console *co, char *options)
874{
875 struct asc_port *ascport;
876 int baud = 115200;
877 int bits = 8;
878 int parity = 'n';
879 int flow = 'n';
880
881 if (co->index >= ASC_MAX_PORTS)
882 return -ENODEV;
883
884 ascport = &asc_ports[co->index];
885
886 /*
887 * This driver does not support early console initialization
888 * (use ARM early printk support instead), so we only expect
889 * this to be called during the uart port registration when the
890 * driver gets probed and the port should be mapped at that point.
891 */
892 if (ascport->port.mapbase == 0 || ascport->port.membase == NULL)
893 return -ENXIO;
894
895 if (options)
896 uart_parse_options(options, &baud, &parity, &bits, &flow);
897
898 return uart_set_options(&ascport->port, co, baud, parity, bits, flow);
899}
900
901static struct console asc_console = {
902 .name = ASC_SERIAL_NAME,
903 .device = uart_console_device,
904 .write = asc_console_write,
905 .setup = asc_console_setup,
906 .flags = CON_PRINTBUFFER,
907 .index = -1,
908 .data = &asc_uart_driver,
909};
910
911#define ASC_SERIAL_CONSOLE (&asc_console)
912
913#else
914#define ASC_SERIAL_CONSOLE NULL
915#endif /* CONFIG_SERIAL_ST_ASC_CONSOLE */
916
917static struct uart_driver asc_uart_driver = {
918 .owner = THIS_MODULE,
919 .driver_name = DRIVER_NAME,
920 .dev_name = ASC_SERIAL_NAME,
921 .major = 0,
922 .minor = 0,
923 .nr = ASC_MAX_PORTS,
924 .cons = ASC_SERIAL_CONSOLE,
925};
926
927static const struct dev_pm_ops asc_serial_pm_ops = {
928 SET_SYSTEM_SLEEP_PM_OPS(asc_serial_suspend, asc_serial_resume)
929};
930
931static struct platform_driver asc_serial_driver = {
932 .probe = asc_serial_probe,
933 .remove_new = asc_serial_remove,
934 .driver = {
935 .name = DRIVER_NAME,
936 .pm = &asc_serial_pm_ops,
937 .of_match_table = of_match_ptr(asc_match),
938 },
939};
940
941static int __init asc_init(void)
942{
943 int ret;
944 static const char banner[] __initconst =
945 KERN_INFO "STMicroelectronics ASC driver initialized\n";
946
947 printk(banner);
948
949 ret = uart_register_driver(&asc_uart_driver);
950 if (ret)
951 return ret;
952
953 ret = platform_driver_register(&asc_serial_driver);
954 if (ret)
955 uart_unregister_driver(&asc_uart_driver);
956
957 return ret;
958}
959
960static void __exit asc_exit(void)
961{
962 platform_driver_unregister(&asc_serial_driver);
963 uart_unregister_driver(&asc_uart_driver);
964}
965
966module_init(asc_init);
967module_exit(asc_exit);
968
969MODULE_ALIAS("platform:" DRIVER_NAME);
970MODULE_AUTHOR("STMicroelectronics (R&D) Limited");
971MODULE_DESCRIPTION("STMicroelectronics ASC serial port driver");
972MODULE_LICENSE("GPL");
1/*
2 * st-asc.c: ST Asynchronous serial controller (ASC) driver
3 *
4 * Copyright (C) 2003-2013 STMicroelectronics (R&D) Limited
5 *
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2 of the License, or
9 * (at your option) any later version.
10 *
11 */
12
13#if defined(CONFIG_SERIAL_ST_ASC_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
14#define SUPPORT_SYSRQ
15#endif
16
17#include <linux/module.h>
18#include <linux/serial.h>
19#include <linux/console.h>
20#include <linux/sysrq.h>
21#include <linux/platform_device.h>
22#include <linux/io.h>
23#include <linux/irq.h>
24#include <linux/tty.h>
25#include <linux/tty_flip.h>
26#include <linux/delay.h>
27#include <linux/spinlock.h>
28#include <linux/pm_runtime.h>
29#include <linux/of.h>
30#include <linux/of_platform.h>
31#include <linux/serial_core.h>
32#include <linux/clk.h>
33
34#define DRIVER_NAME "st-asc"
35#define ASC_SERIAL_NAME "ttyAS"
36#define ASC_FIFO_SIZE 16
37#define ASC_MAX_PORTS 8
38
39struct asc_port {
40 struct uart_port port;
41 struct clk *clk;
42 unsigned int hw_flow_control:1;
43 unsigned int force_m1:1;
44};
45
46static struct asc_port asc_ports[ASC_MAX_PORTS];
47static struct uart_driver asc_uart_driver;
48
49/*---- UART Register definitions ------------------------------*/
50
51/* Register offsets */
52
53#define ASC_BAUDRATE 0x00
54#define ASC_TXBUF 0x04
55#define ASC_RXBUF 0x08
56#define ASC_CTL 0x0C
57#define ASC_INTEN 0x10
58#define ASC_STA 0x14
59#define ASC_GUARDTIME 0x18
60#define ASC_TIMEOUT 0x1C
61#define ASC_TXRESET 0x20
62#define ASC_RXRESET 0x24
63#define ASC_RETRIES 0x28
64
65/* ASC_RXBUF */
66#define ASC_RXBUF_PE 0x100
67#define ASC_RXBUF_FE 0x200
68/**
69 * Some of status comes from higher bits of the character and some come from
70 * the status register. Combining both of them in to single status using dummy
71 * bits.
72 */
73#define ASC_RXBUF_DUMMY_RX 0x10000
74#define ASC_RXBUF_DUMMY_BE 0x20000
75#define ASC_RXBUF_DUMMY_OE 0x40000
76
77/* ASC_CTL */
78
79#define ASC_CTL_MODE_MSK 0x0007
80#define ASC_CTL_MODE_8BIT 0x0001
81#define ASC_CTL_MODE_7BIT_PAR 0x0003
82#define ASC_CTL_MODE_9BIT 0x0004
83#define ASC_CTL_MODE_8BIT_WKUP 0x0005
84#define ASC_CTL_MODE_8BIT_PAR 0x0007
85#define ASC_CTL_STOP_MSK 0x0018
86#define ASC_CTL_STOP_HALFBIT 0x0000
87#define ASC_CTL_STOP_1BIT 0x0008
88#define ASC_CTL_STOP_1_HALFBIT 0x0010
89#define ASC_CTL_STOP_2BIT 0x0018
90#define ASC_CTL_PARITYODD 0x0020
91#define ASC_CTL_LOOPBACK 0x0040
92#define ASC_CTL_RUN 0x0080
93#define ASC_CTL_RXENABLE 0x0100
94#define ASC_CTL_SCENABLE 0x0200
95#define ASC_CTL_FIFOENABLE 0x0400
96#define ASC_CTL_CTSENABLE 0x0800
97#define ASC_CTL_BAUDMODE 0x1000
98
99/* ASC_GUARDTIME */
100
101#define ASC_GUARDTIME_MSK 0x00FF
102
103/* ASC_INTEN */
104
105#define ASC_INTEN_RBE 0x0001
106#define ASC_INTEN_TE 0x0002
107#define ASC_INTEN_THE 0x0004
108#define ASC_INTEN_PE 0x0008
109#define ASC_INTEN_FE 0x0010
110#define ASC_INTEN_OE 0x0020
111#define ASC_INTEN_TNE 0x0040
112#define ASC_INTEN_TOI 0x0080
113#define ASC_INTEN_RHF 0x0100
114
115/* ASC_RETRIES */
116
117#define ASC_RETRIES_MSK 0x00FF
118
119/* ASC_RXBUF */
120
121#define ASC_RXBUF_MSK 0x03FF
122
123/* ASC_STA */
124
125#define ASC_STA_RBF 0x0001
126#define ASC_STA_TE 0x0002
127#define ASC_STA_THE 0x0004
128#define ASC_STA_PE 0x0008
129#define ASC_STA_FE 0x0010
130#define ASC_STA_OE 0x0020
131#define ASC_STA_TNE 0x0040
132#define ASC_STA_TOI 0x0080
133#define ASC_STA_RHF 0x0100
134#define ASC_STA_TF 0x0200
135#define ASC_STA_NKD 0x0400
136
137/* ASC_TIMEOUT */
138
139#define ASC_TIMEOUT_MSK 0x00FF
140
141/* ASC_TXBUF */
142
143#define ASC_TXBUF_MSK 0x01FF
144
145/*---- Inline function definitions ---------------------------*/
146
147static inline struct asc_port *to_asc_port(struct uart_port *port)
148{
149 return container_of(port, struct asc_port, port);
150}
151
152static inline u32 asc_in(struct uart_port *port, u32 offset)
153{
154#ifdef readl_relaxed
155 return readl_relaxed(port->membase + offset);
156#else
157 return readl(port->membase + offset);
158#endif
159}
160
161static inline void asc_out(struct uart_port *port, u32 offset, u32 value)
162{
163#ifdef writel_relaxed
164 writel_relaxed(value, port->membase + offset);
165#else
166 writel(value, port->membase + offset);
167#endif
168}
169
170/*
171 * Some simple utility functions to enable and disable interrupts.
172 * Note that these need to be called with interrupts disabled.
173 */
174static inline void asc_disable_tx_interrupts(struct uart_port *port)
175{
176 u32 intenable = asc_in(port, ASC_INTEN) & ~ASC_INTEN_THE;
177 asc_out(port, ASC_INTEN, intenable);
178 (void)asc_in(port, ASC_INTEN); /* Defeat bus write posting */
179}
180
181static inline void asc_enable_tx_interrupts(struct uart_port *port)
182{
183 u32 intenable = asc_in(port, ASC_INTEN) | ASC_INTEN_THE;
184 asc_out(port, ASC_INTEN, intenable);
185}
186
187static inline void asc_disable_rx_interrupts(struct uart_port *port)
188{
189 u32 intenable = asc_in(port, ASC_INTEN) & ~ASC_INTEN_RBE;
190 asc_out(port, ASC_INTEN, intenable);
191 (void)asc_in(port, ASC_INTEN); /* Defeat bus write posting */
192}
193
194static inline void asc_enable_rx_interrupts(struct uart_port *port)
195{
196 u32 intenable = asc_in(port, ASC_INTEN) | ASC_INTEN_RBE;
197 asc_out(port, ASC_INTEN, intenable);
198}
199
200static inline u32 asc_txfifo_is_empty(struct uart_port *port)
201{
202 return asc_in(port, ASC_STA) & ASC_STA_TE;
203}
204
205static inline u32 asc_txfifo_is_half_empty(struct uart_port *port)
206{
207 return asc_in(port, ASC_STA) & ASC_STA_THE;
208}
209
210static inline const char *asc_port_name(struct uart_port *port)
211{
212 return to_platform_device(port->dev)->name;
213}
214
215/*----------------------------------------------------------------------*/
216
217/*
218 * This section contains code to support the use of the ASC as a
219 * generic serial port.
220 */
221
222static inline unsigned asc_hw_txroom(struct uart_port *port)
223{
224 u32 status = asc_in(port, ASC_STA);
225
226 if (status & ASC_STA_THE)
227 return port->fifosize / 2;
228 else if (!(status & ASC_STA_TF))
229 return 1;
230
231 return 0;
232}
233
234/*
235 * Start transmitting chars.
236 * This is called from both interrupt and task level.
237 * Either way interrupts are disabled.
238 */
239static void asc_transmit_chars(struct uart_port *port)
240{
241 struct circ_buf *xmit = &port->state->xmit;
242 int txroom;
243 unsigned char c;
244
245 txroom = asc_hw_txroom(port);
246
247 if ((txroom != 0) && port->x_char) {
248 c = port->x_char;
249 port->x_char = 0;
250 asc_out(port, ASC_TXBUF, c);
251 port->icount.tx++;
252 txroom = asc_hw_txroom(port);
253 }
254
255 if (uart_tx_stopped(port)) {
256 /*
257 * We should try and stop the hardware here, but I
258 * don't think the ASC has any way to do that.
259 */
260 asc_disable_tx_interrupts(port);
261 return;
262 }
263
264 if (uart_circ_empty(xmit)) {
265 asc_disable_tx_interrupts(port);
266 return;
267 }
268
269 if (txroom == 0)
270 return;
271
272 do {
273 c = xmit->buf[xmit->tail];
274 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
275 asc_out(port, ASC_TXBUF, c);
276 port->icount.tx++;
277 txroom--;
278 } while ((txroom > 0) && (!uart_circ_empty(xmit)));
279
280 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
281 uart_write_wakeup(port);
282
283 if (uart_circ_empty(xmit))
284 asc_disable_tx_interrupts(port);
285}
286
287static void asc_receive_chars(struct uart_port *port)
288{
289 struct tty_port *tport = &port->state->port;
290 unsigned long status;
291 unsigned long c = 0;
292 char flag;
293
294 if (port->irq_wake)
295 pm_wakeup_event(tport->tty->dev, 0);
296
297 while ((status = asc_in(port, ASC_STA)) & ASC_STA_RBF) {
298 c = asc_in(port, ASC_RXBUF) | ASC_RXBUF_DUMMY_RX;
299 flag = TTY_NORMAL;
300 port->icount.rx++;
301
302 if ((c & (ASC_RXBUF_FE | ASC_RXBUF_PE)) ||
303 status & ASC_STA_OE) {
304
305 if (c & ASC_RXBUF_FE) {
306 if (c == (ASC_RXBUF_FE | ASC_RXBUF_DUMMY_RX)) {
307 port->icount.brk++;
308 if (uart_handle_break(port))
309 continue;
310 c |= ASC_RXBUF_DUMMY_BE;
311 } else {
312 port->icount.frame++;
313 }
314 } else if (c & ASC_RXBUF_PE) {
315 port->icount.parity++;
316 }
317 /*
318 * Reading any data from the RX FIFO clears the
319 * overflow error condition.
320 */
321 if (status & ASC_STA_OE) {
322 port->icount.overrun++;
323 c |= ASC_RXBUF_DUMMY_OE;
324 }
325
326 c &= port->read_status_mask;
327
328 if (c & ASC_RXBUF_DUMMY_BE)
329 flag = TTY_BREAK;
330 else if (c & ASC_RXBUF_PE)
331 flag = TTY_PARITY;
332 else if (c & ASC_RXBUF_FE)
333 flag = TTY_FRAME;
334 }
335
336 if (uart_handle_sysrq_char(port, c & 0xff))
337 continue;
338
339 uart_insert_char(port, c, ASC_RXBUF_DUMMY_OE, c & 0xff, flag);
340 }
341
342 /* Tell the rest of the system the news. New characters! */
343 tty_flip_buffer_push(tport);
344}
345
346static irqreturn_t asc_interrupt(int irq, void *ptr)
347{
348 struct uart_port *port = ptr;
349 u32 status;
350
351 spin_lock(&port->lock);
352
353 status = asc_in(port, ASC_STA);
354
355 if (status & ASC_STA_RBF) {
356 /* Receive FIFO not empty */
357 asc_receive_chars(port);
358 }
359
360 if ((status & ASC_STA_THE) &&
361 (asc_in(port, ASC_INTEN) & ASC_INTEN_THE)) {
362 /* Transmitter FIFO at least half empty */
363 asc_transmit_chars(port);
364 }
365
366 spin_unlock(&port->lock);
367
368 return IRQ_HANDLED;
369}
370
371/*----------------------------------------------------------------------*/
372
373/*
374 * UART Functions
375 */
376
377static unsigned int asc_tx_empty(struct uart_port *port)
378{
379 return asc_txfifo_is_empty(port) ? TIOCSER_TEMT : 0;
380}
381
382static void asc_set_mctrl(struct uart_port *port, unsigned int mctrl)
383{
384 /*
385 * This routine is used for seting signals of: DTR, DCD, CTS/RTS
386 * We use ASC's hardware for CTS/RTS, so don't need any for that.
387 * Some boards have DTR and DCD implemented using PIO pins,
388 * code to do this should be hooked in here.
389 */
390}
391
392static unsigned int asc_get_mctrl(struct uart_port *port)
393{
394 /*
395 * This routine is used for geting signals of: DTR, DCD, DSR, RI,
396 * and CTS/RTS
397 */
398 return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
399}
400
401/* There are probably characters waiting to be transmitted. */
402static void asc_start_tx(struct uart_port *port)
403{
404 struct circ_buf *xmit = &port->state->xmit;
405
406 if (!uart_circ_empty(xmit))
407 asc_enable_tx_interrupts(port);
408}
409
410/* Transmit stop */
411static void asc_stop_tx(struct uart_port *port)
412{
413 asc_disable_tx_interrupts(port);
414}
415
416/* Receive stop */
417static void asc_stop_rx(struct uart_port *port)
418{
419 asc_disable_rx_interrupts(port);
420}
421
422/* Handle breaks - ignored by us */
423static void asc_break_ctl(struct uart_port *port, int break_state)
424{
425 /* Nothing here yet .. */
426}
427
428/*
429 * Enable port for reception.
430 */
431static int asc_startup(struct uart_port *port)
432{
433 if (request_irq(port->irq, asc_interrupt, 0,
434 asc_port_name(port), port)) {
435 dev_err(port->dev, "cannot allocate irq.\n");
436 return -ENODEV;
437 }
438
439 asc_transmit_chars(port);
440 asc_enable_rx_interrupts(port);
441
442 return 0;
443}
444
445static void asc_shutdown(struct uart_port *port)
446{
447 asc_disable_tx_interrupts(port);
448 asc_disable_rx_interrupts(port);
449 free_irq(port->irq, port);
450}
451
452static void asc_pm(struct uart_port *port, unsigned int state,
453 unsigned int oldstate)
454{
455 struct asc_port *ascport = to_asc_port(port);
456 unsigned long flags = 0;
457 u32 ctl;
458
459 switch (state) {
460 case UART_PM_STATE_ON:
461 clk_prepare_enable(ascport->clk);
462 break;
463 case UART_PM_STATE_OFF:
464 /*
465 * Disable the ASC baud rate generator, which is as close as
466 * we can come to turning it off. Note this is not called with
467 * the port spinlock held.
468 */
469 spin_lock_irqsave(&port->lock, flags);
470 ctl = asc_in(port, ASC_CTL) & ~ASC_CTL_RUN;
471 asc_out(port, ASC_CTL, ctl);
472 spin_unlock_irqrestore(&port->lock, flags);
473 clk_disable_unprepare(ascport->clk);
474 break;
475 }
476}
477
478static void asc_set_termios(struct uart_port *port, struct ktermios *termios,
479 struct ktermios *old)
480{
481 struct asc_port *ascport = to_asc_port(port);
482 unsigned int baud;
483 u32 ctrl_val;
484 tcflag_t cflag;
485 unsigned long flags;
486
487 /* Update termios to reflect hardware capabilities */
488 termios->c_cflag &= ~(CMSPAR |
489 (ascport->hw_flow_control ? 0 : CRTSCTS));
490
491 port->uartclk = clk_get_rate(ascport->clk);
492
493 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
494 cflag = termios->c_cflag;
495
496 spin_lock_irqsave(&port->lock, flags);
497
498 /* read control register */
499 ctrl_val = asc_in(port, ASC_CTL);
500
501 /* stop serial port and reset value */
502 asc_out(port, ASC_CTL, (ctrl_val & ~ASC_CTL_RUN));
503 ctrl_val = ASC_CTL_RXENABLE | ASC_CTL_FIFOENABLE;
504
505 /* reset fifo rx & tx */
506 asc_out(port, ASC_TXRESET, 1);
507 asc_out(port, ASC_RXRESET, 1);
508
509 /* set character length */
510 if ((cflag & CSIZE) == CS7) {
511 ctrl_val |= ASC_CTL_MODE_7BIT_PAR;
512 } else {
513 ctrl_val |= (cflag & PARENB) ? ASC_CTL_MODE_8BIT_PAR :
514 ASC_CTL_MODE_8BIT;
515 }
516
517 /* set stop bit */
518 ctrl_val |= (cflag & CSTOPB) ? ASC_CTL_STOP_2BIT : ASC_CTL_STOP_1BIT;
519
520 /* odd parity */
521 if (cflag & PARODD)
522 ctrl_val |= ASC_CTL_PARITYODD;
523
524 /* hardware flow control */
525 if ((cflag & CRTSCTS))
526 ctrl_val |= ASC_CTL_CTSENABLE;
527
528 if ((baud < 19200) && !ascport->force_m1) {
529 asc_out(port, ASC_BAUDRATE, (port->uartclk / (16 * baud)));
530 } else {
531 /*
532 * MODE 1: recommended for high bit rates (above 19.2K)
533 *
534 * baudrate * 16 * 2^16
535 * ASCBaudRate = ------------------------
536 * inputclock
537 *
538 * To keep maths inside 64bits, we divide inputclock by 16.
539 */
540 u64 dividend = (u64)baud * (1 << 16);
541
542 do_div(dividend, port->uartclk / 16);
543 asc_out(port, ASC_BAUDRATE, dividend);
544 ctrl_val |= ASC_CTL_BAUDMODE;
545 }
546
547 uart_update_timeout(port, cflag, baud);
548
549 ascport->port.read_status_mask = ASC_RXBUF_DUMMY_OE;
550 if (termios->c_iflag & INPCK)
551 ascport->port.read_status_mask |= ASC_RXBUF_FE | ASC_RXBUF_PE;
552 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
553 ascport->port.read_status_mask |= ASC_RXBUF_DUMMY_BE;
554
555 /*
556 * Characters to ignore
557 */
558 ascport->port.ignore_status_mask = 0;
559 if (termios->c_iflag & IGNPAR)
560 ascport->port.ignore_status_mask |= ASC_RXBUF_FE | ASC_RXBUF_PE;
561 if (termios->c_iflag & IGNBRK) {
562 ascport->port.ignore_status_mask |= ASC_RXBUF_DUMMY_BE;
563 /*
564 * If we're ignoring parity and break indicators,
565 * ignore overruns too (for real raw support).
566 */
567 if (termios->c_iflag & IGNPAR)
568 ascport->port.ignore_status_mask |= ASC_RXBUF_DUMMY_OE;
569 }
570
571 /*
572 * Ignore all characters if CREAD is not set.
573 */
574 if (!(termios->c_cflag & CREAD))
575 ascport->port.ignore_status_mask |= ASC_RXBUF_DUMMY_RX;
576
577 /* Set the timeout */
578 asc_out(port, ASC_TIMEOUT, 20);
579
580 /* write final value and enable port */
581 asc_out(port, ASC_CTL, (ctrl_val | ASC_CTL_RUN));
582
583 spin_unlock_irqrestore(&port->lock, flags);
584}
585
586static const char *asc_type(struct uart_port *port)
587{
588 return (port->type == PORT_ASC) ? DRIVER_NAME : NULL;
589}
590
591static void asc_release_port(struct uart_port *port)
592{
593}
594
595static int asc_request_port(struct uart_port *port)
596{
597 return 0;
598}
599
600/*
601 * Called when the port is opened, and UPF_BOOT_AUTOCONF flag is set
602 * Set type field if successful
603 */
604static void asc_config_port(struct uart_port *port, int flags)
605{
606 if ((flags & UART_CONFIG_TYPE))
607 port->type = PORT_ASC;
608}
609
610static int
611asc_verify_port(struct uart_port *port, struct serial_struct *ser)
612{
613 /* No user changeable parameters */
614 return -EINVAL;
615}
616
617#ifdef CONFIG_CONSOLE_POLL
618/*
619 * Console polling routines for writing and reading from the uart while
620 * in an interrupt or debug context (i.e. kgdb).
621 */
622
623static int asc_get_poll_char(struct uart_port *port)
624{
625 if (!(asc_in(port, ASC_STA) & ASC_STA_RBF))
626 return NO_POLL_CHAR;
627
628 return asc_in(port, ASC_RXBUF);
629}
630
631static void asc_put_poll_char(struct uart_port *port, unsigned char c)
632{
633 while (!asc_txfifo_is_half_empty(port))
634 cpu_relax();
635 asc_out(port, ASC_TXBUF, c);
636}
637
638#endif /* CONFIG_CONSOLE_POLL */
639
640/*---------------------------------------------------------------------*/
641
642static struct uart_ops asc_uart_ops = {
643 .tx_empty = asc_tx_empty,
644 .set_mctrl = asc_set_mctrl,
645 .get_mctrl = asc_get_mctrl,
646 .start_tx = asc_start_tx,
647 .stop_tx = asc_stop_tx,
648 .stop_rx = asc_stop_rx,
649 .break_ctl = asc_break_ctl,
650 .startup = asc_startup,
651 .shutdown = asc_shutdown,
652 .set_termios = asc_set_termios,
653 .type = asc_type,
654 .release_port = asc_release_port,
655 .request_port = asc_request_port,
656 .config_port = asc_config_port,
657 .verify_port = asc_verify_port,
658 .pm = asc_pm,
659#ifdef CONFIG_CONSOLE_POLL
660 .poll_get_char = asc_get_poll_char,
661 .poll_put_char = asc_put_poll_char,
662#endif /* CONFIG_CONSOLE_POLL */
663};
664
665static int asc_init_port(struct asc_port *ascport,
666 struct platform_device *pdev)
667{
668 struct uart_port *port = &ascport->port;
669 struct resource *res;
670
671 port->iotype = UPIO_MEM;
672 port->flags = UPF_BOOT_AUTOCONF;
673 port->ops = &asc_uart_ops;
674 port->fifosize = ASC_FIFO_SIZE;
675 port->dev = &pdev->dev;
676 port->irq = platform_get_irq(pdev, 0);
677
678 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
679 port->membase = devm_ioremap_resource(&pdev->dev, res);
680 if (IS_ERR(port->membase))
681 return PTR_ERR(port->membase);
682 port->mapbase = res->start;
683
684 spin_lock_init(&port->lock);
685
686 ascport->clk = devm_clk_get(&pdev->dev, NULL);
687
688 if (WARN_ON(IS_ERR(ascport->clk)))
689 return -EINVAL;
690 /* ensure that clk rate is correct by enabling the clk */
691 clk_prepare_enable(ascport->clk);
692 ascport->port.uartclk = clk_get_rate(ascport->clk);
693 WARN_ON(ascport->port.uartclk == 0);
694 clk_disable_unprepare(ascport->clk);
695
696 return 0;
697}
698
699static struct asc_port *asc_of_get_asc_port(struct platform_device *pdev)
700{
701 struct device_node *np = pdev->dev.of_node;
702 int id;
703
704 if (!np)
705 return NULL;
706
707 id = of_alias_get_id(np, ASC_SERIAL_NAME);
708
709 if (id < 0)
710 id = 0;
711
712 if (WARN_ON(id >= ASC_MAX_PORTS))
713 return NULL;
714
715 asc_ports[id].hw_flow_control = of_property_read_bool(np,
716 "st,hw-flow-control");
717 asc_ports[id].force_m1 = of_property_read_bool(np, "st,force_m1");
718 asc_ports[id].port.line = id;
719 return &asc_ports[id];
720}
721
722#ifdef CONFIG_OF
723static const struct of_device_id asc_match[] = {
724 { .compatible = "st,asc", },
725 {},
726};
727
728MODULE_DEVICE_TABLE(of, asc_match);
729#endif
730
731static int asc_serial_probe(struct platform_device *pdev)
732{
733 int ret;
734 struct asc_port *ascport;
735
736 ascport = asc_of_get_asc_port(pdev);
737 if (!ascport)
738 return -ENODEV;
739
740 ret = asc_init_port(ascport, pdev);
741 if (ret)
742 return ret;
743
744 ret = uart_add_one_port(&asc_uart_driver, &ascport->port);
745 if (ret)
746 return ret;
747
748 platform_set_drvdata(pdev, &ascport->port);
749
750 return 0;
751}
752
753static int asc_serial_remove(struct platform_device *pdev)
754{
755 struct uart_port *port = platform_get_drvdata(pdev);
756
757 return uart_remove_one_port(&asc_uart_driver, port);
758}
759
760#ifdef CONFIG_PM_SLEEP
761static int asc_serial_suspend(struct device *dev)
762{
763 struct platform_device *pdev = to_platform_device(dev);
764 struct uart_port *port = platform_get_drvdata(pdev);
765
766 return uart_suspend_port(&asc_uart_driver, port);
767}
768
769static int asc_serial_resume(struct device *dev)
770{
771 struct platform_device *pdev = to_platform_device(dev);
772 struct uart_port *port = platform_get_drvdata(pdev);
773
774 return uart_resume_port(&asc_uart_driver, port);
775}
776
777#endif /* CONFIG_PM_SLEEP */
778
779/*----------------------------------------------------------------------*/
780
781#ifdef CONFIG_SERIAL_ST_ASC_CONSOLE
782static void asc_console_putchar(struct uart_port *port, int ch)
783{
784 unsigned int timeout = 1000000;
785
786 /* Wait for upto 1 second in case flow control is stopping us. */
787 while (--timeout && !asc_txfifo_is_half_empty(port))
788 udelay(1);
789
790 asc_out(port, ASC_TXBUF, ch);
791}
792
793/*
794 * Print a string to the serial port trying not to disturb
795 * any possible real use of the port...
796 */
797
798static void asc_console_write(struct console *co, const char *s, unsigned count)
799{
800 struct uart_port *port = &asc_ports[co->index].port;
801 unsigned long flags;
802 unsigned long timeout = 1000000;
803 int locked = 1;
804 u32 intenable;
805
806 local_irq_save(flags);
807 if (port->sysrq)
808 locked = 0; /* asc_interrupt has already claimed the lock */
809 else if (oops_in_progress)
810 locked = spin_trylock(&port->lock);
811 else
812 spin_lock(&port->lock);
813
814 /*
815 * Disable interrupts so we don't get the IRQ line bouncing
816 * up and down while interrupts are disabled.
817 */
818 intenable = asc_in(port, ASC_INTEN);
819 asc_out(port, ASC_INTEN, 0);
820 (void)asc_in(port, ASC_INTEN); /* Defeat bus write posting */
821
822 uart_console_write(port, s, count, asc_console_putchar);
823
824 while (--timeout && !asc_txfifo_is_empty(port))
825 udelay(1);
826
827 asc_out(port, ASC_INTEN, intenable);
828
829 if (locked)
830 spin_unlock(&port->lock);
831 local_irq_restore(flags);
832}
833
834static int asc_console_setup(struct console *co, char *options)
835{
836 struct asc_port *ascport;
837 int baud = 9600;
838 int bits = 8;
839 int parity = 'n';
840 int flow = 'n';
841
842 if (co->index >= ASC_MAX_PORTS)
843 return -ENODEV;
844
845 ascport = &asc_ports[co->index];
846
847 /*
848 * This driver does not support early console initialization
849 * (use ARM early printk support instead), so we only expect
850 * this to be called during the uart port registration when the
851 * driver gets probed and the port should be mapped at that point.
852 */
853 if (ascport->port.mapbase == 0 || ascport->port.membase == NULL)
854 return -ENXIO;
855
856 if (options)
857 uart_parse_options(options, &baud, &parity, &bits, &flow);
858
859 return uart_set_options(&ascport->port, co, baud, parity, bits, flow);
860}
861
862static struct console asc_console = {
863 .name = ASC_SERIAL_NAME,
864 .device = uart_console_device,
865 .write = asc_console_write,
866 .setup = asc_console_setup,
867 .flags = CON_PRINTBUFFER,
868 .index = -1,
869 .data = &asc_uart_driver,
870};
871
872#define ASC_SERIAL_CONSOLE (&asc_console)
873
874#else
875#define ASC_SERIAL_CONSOLE NULL
876#endif /* CONFIG_SERIAL_ST_ASC_CONSOLE */
877
878static struct uart_driver asc_uart_driver = {
879 .owner = THIS_MODULE,
880 .driver_name = DRIVER_NAME,
881 .dev_name = ASC_SERIAL_NAME,
882 .major = 0,
883 .minor = 0,
884 .nr = ASC_MAX_PORTS,
885 .cons = ASC_SERIAL_CONSOLE,
886};
887
888static const struct dev_pm_ops asc_serial_pm_ops = {
889 SET_SYSTEM_SLEEP_PM_OPS(asc_serial_suspend, asc_serial_resume)
890};
891
892static struct platform_driver asc_serial_driver = {
893 .probe = asc_serial_probe,
894 .remove = asc_serial_remove,
895 .driver = {
896 .name = DRIVER_NAME,
897 .pm = &asc_serial_pm_ops,
898 .of_match_table = of_match_ptr(asc_match),
899 },
900};
901
902static int __init asc_init(void)
903{
904 int ret;
905 static char banner[] __initdata =
906 KERN_INFO "STMicroelectronics ASC driver initialized\n";
907
908 printk(banner);
909
910 ret = uart_register_driver(&asc_uart_driver);
911 if (ret)
912 return ret;
913
914 ret = platform_driver_register(&asc_serial_driver);
915 if (ret)
916 uart_unregister_driver(&asc_uart_driver);
917
918 return ret;
919}
920
921static void __exit asc_exit(void)
922{
923 platform_driver_unregister(&asc_serial_driver);
924 uart_unregister_driver(&asc_uart_driver);
925}
926
927module_init(asc_init);
928module_exit(asc_exit);
929
930MODULE_ALIAS("platform:" DRIVER_NAME);
931MODULE_AUTHOR("STMicroelectronics (R&D) Limited");
932MODULE_DESCRIPTION("STMicroelectronics ASC serial port driver");
933MODULE_LICENSE("GPL");