1# SPDX-License-Identifier: GPL-2.0-only
 2#
 3# Qualcomm network device configuration
 4#
 5
 6config NET_VENDOR_QUALCOMM
 7	bool "Qualcomm devices"
 8	default y
 9	help
10	  If you have a network (Ethernet) card belonging to this class, say Y.
11
12	  Note that the answer to this question doesn't directly affect the
13	  kernel: saying N will just cause the configurator to skip all
14	  the questions about Qualcomm cards. If you say Y, you will be asked
15	  for your specific card in the following questions.
16
17if NET_VENDOR_QUALCOMM
18
19config QCA7000
20	tristate
21	help
22	  This enables support for the Qualcomm Atheros QCA7000.
23
24config QCA7000_SPI
25	tristate "Qualcomm Atheros QCA7000 SPI support"
26	select QCA7000
27	depends on SPI_MASTER && OF
28	help
29	  This SPI protocol driver supports the Qualcomm Atheros QCA7000.
30
31	  To compile this driver as a module, choose M here. The module
32	  will be called qcaspi.
33
34config QCA7000_UART
35	tristate "Qualcomm Atheros QCA7000 UART support"
36	select QCA7000
37	depends on SERIAL_DEV_BUS && OF
38	help
39	  This UART protocol driver supports the Qualcomm Atheros QCA7000.
40
41	  Currently the driver assumes these device UART settings:
42	    Data bits: 8
43	    Parity: None
44	    Stop bits: 1
45	    Flow control: None
46
47	  To compile this driver as a module, choose M here. The module
48	  will be called qcauart.
49
50config QCOM_EMAC
51	tristate "Qualcomm Technologies, Inc. EMAC Gigabit Ethernet support"
52	depends on HAS_DMA && HAS_IOMEM
53	select CRC32
54	select PHYLIB
55	select MDIO_DEVRES
56	help
57	  This driver supports the Qualcomm Technologies, Inc. Gigabit
58	  Ethernet Media Access Controller (EMAC). The controller
59	  supports IEEE 802.3-2002, half-duplex mode at 10/100 Mb/s,
60	  full-duplex mode at 10/100/1000Mb/s, Wake On LAN (WOL) for
61	  low power, Receive-Side Scaling (RSS), and IEEE 1588-2008
62	  Precision Clock Synchronization Protocol.
63
64source "drivers/net/ethernet/qualcomm/rmnet/Kconfig"
65
66endif # NET_VENDOR_QUALCOMM

 
 1#
 2# Qualcomm network device configuration
 3#
 4
 5config NET_VENDOR_QUALCOMM
 6	bool "Qualcomm devices"
 7	default y
 8	---help---
 9	  If you have a network (Ethernet) card belonging to this class, say Y.
10
11	  Note that the answer to this question doesn't directly affect the
12	  kernel: saying N will just cause the configurator to skip all
13	  the questions about Qualcomm cards. If you say Y, you will be asked
14	  for your specific card in the following questions.
15
16if NET_VENDOR_QUALCOMM
17
18config QCA7000
19	tristate
20	help
21	  This enables support for the Qualcomm Atheros QCA7000.
22
23config QCA7000_SPI
24	tristate "Qualcomm Atheros QCA7000 SPI support"
25	select QCA7000
26	depends on SPI_MASTER && OF
27	---help---
28	  This SPI protocol driver supports the Qualcomm Atheros QCA7000.
29
30	  To compile this driver as a module, choose M here. The module
31	  will be called qcaspi.
32
33config QCA7000_UART
34	tristate "Qualcomm Atheros QCA7000 UART support"
35	select QCA7000
36	depends on SERIAL_DEV_BUS && OF
37	---help---
38	  This UART protocol driver supports the Qualcomm Atheros QCA7000.
39
40	  Currently the driver assumes these device UART settings:
41	    Data bits: 8
42	    Parity: None
43	    Stop bits: 1
44	    Flow control: None
45
46	  To compile this driver as a module, choose M here. The module
47	  will be called qcauart.
48
49config QCOM_EMAC
50	tristate "Qualcomm Technologies, Inc. EMAC Gigabit Ethernet support"
51	depends on HAS_DMA && HAS_IOMEM
52	select CRC32
53	select PHYLIB
54	---help---
 
55	  This driver supports the Qualcomm Technologies, Inc. Gigabit
56	  Ethernet Media Access Controller (EMAC). The controller
57	  supports IEEE 802.3-2002, half-duplex mode at 10/100 Mb/s,
58	  full-duplex mode at 10/100/1000Mb/s, Wake On LAN (WOL) for
59	  low power, Receive-Side Scaling (RSS), and IEEE 1588-2008
60	  Precision Clock Synchronization Protocol.
61
62source "drivers/net/ethernet/qualcomm/rmnet/Kconfig"
63
64endif # NET_VENDOR_QUALCOMM