Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * lm75.c - Part of lm_sensors, Linux kernel modules for hardware
4 * monitoring
5 * Copyright (c) 1998, 1999 Frodo Looijaard <frodol@dds.nl>
6 */
7
8#include <linux/module.h>
9#include <linux/init.h>
10#include <linux/interrupt.h>
11#include <linux/slab.h>
12#include <linux/jiffies.h>
13#include <linux/i2c.h>
14#include <linux/hwmon.h>
15#include <linux/err.h>
16#include <linux/of.h>
17#include <linux/regmap.h>
18#include <linux/util_macros.h>
19#include <linux/regulator/consumer.h>
20#include "lm75.h"
21
22/*
23 * This driver handles the LM75 and compatible digital temperature sensors.
24 */
25
26enum lm75_type { /* keep sorted in alphabetical order */
27 adt75,
28 as6200,
29 at30ts74,
30 ds1775,
31 ds75,
32 ds7505,
33 g751,
34 lm75,
35 lm75a,
36 lm75b,
37 max6625,
38 max6626,
39 max31725,
40 mcp980x,
41 pct2075,
42 stds75,
43 stlm75,
44 tcn75,
45 tmp100,
46 tmp101,
47 tmp105,
48 tmp112,
49 tmp175,
50 tmp275,
51 tmp75,
52 tmp75b,
53 tmp75c,
54 tmp1075,
55};
56
57/**
58 * struct lm75_params - lm75 configuration parameters.
59 * @config_reg_16bits: Configure register size is 2 bytes.
60 * @set_mask: Bits to set in configuration register when configuring
61 * the chip.
62 * @clr_mask: Bits to clear in configuration register when configuring
63 * the chip.
64 * @default_resolution: Default number of bits to represent the temperature
65 * value.
66 * @resolution_limits: Limit register resolution. Optional. Should be set if
67 * the resolution of limit registers does not match the
68 * resolution of the temperature register.
69 * @resolutions: List of resolutions associated with sample times.
70 * Optional. Should be set if num_sample_times is larger
71 * than 1, and if the resolution changes with sample times.
72 * If set, number of entries must match num_sample_times.
73 * @default_sample_time:Sample time to be set by default.
74 * @num_sample_times: Number of possible sample times to be set. Optional.
75 * Should be set if the number of sample times is larger
76 * than one.
77 * @sample_times: All the possible sample times to be set. Mandatory if
78 * num_sample_times is larger than 1. If set, number of
79 * entries must match num_sample_times.
80 * @alarm: Alarm bit is supported.
81 */
82
83struct lm75_params {
84 bool config_reg_16bits;
85 u16 set_mask;
86 u16 clr_mask;
87 u8 default_resolution;
88 u8 resolution_limits;
89 const u8 *resolutions;
90 unsigned int default_sample_time;
91 u8 num_sample_times;
92 const unsigned int *sample_times;
93 bool alarm;
94};
95
96/* Addresses scanned */
97static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c,
98 0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
99
100/* The LM75 registers */
101#define LM75_REG_TEMP 0x00
102#define LM75_REG_CONF 0x01
103#define LM75_REG_HYST 0x02
104#define LM75_REG_MAX 0x03
105#define PCT2075_REG_IDLE 0x04
106
107/* Each client has this additional data */
108struct lm75_data {
109 struct i2c_client *client;
110 struct regmap *regmap;
111 struct regulator *vs;
112 u16 orig_conf;
113 u16 current_conf;
114 u8 resolution; /* In bits, 9 to 16 */
115 unsigned int sample_time; /* In ms */
116 enum lm75_type kind;
117 const struct lm75_params *params;
118};
119
120/*-----------------------------------------------------------------------*/
121
122static const u8 lm75_sample_set_masks[] = { 0 << 5, 1 << 5, 2 << 5, 3 << 5 };
123
124#define LM75_SAMPLE_CLEAR_MASK (3 << 5)
125
126/* The structure below stores the configuration values of the supported devices.
127 * In case of being supported multiple configurations, the default one must
128 * always be the first element of the array
129 */
130static const struct lm75_params device_params[] = {
131 [adt75] = {
132 .clr_mask = 1 << 5, /* not one-shot mode */
133 .default_resolution = 12,
134 .default_sample_time = MSEC_PER_SEC / 10,
135 },
136 [as6200] = {
137 .config_reg_16bits = true,
138 .set_mask = 0x94C0, /* 8 sample/s, 4 CF, positive polarity */
139 .default_resolution = 12,
140 .default_sample_time = 125,
141 .num_sample_times = 4,
142 .sample_times = (unsigned int []){ 125, 250, 1000, 4000 },
143 .alarm = true,
144 },
145 [at30ts74] = {
146 .set_mask = 3 << 5, /* 12-bit mode*/
147 .default_resolution = 12,
148 .default_sample_time = 200,
149 .num_sample_times = 4,
150 .sample_times = (unsigned int []){ 25, 50, 100, 200 },
151 .resolutions = (u8 []) {9, 10, 11, 12 },
152 },
153 [ds1775] = {
154 .clr_mask = 3 << 5,
155 .set_mask = 2 << 5, /* 11-bit mode */
156 .default_resolution = 11,
157 .default_sample_time = 500,
158 .num_sample_times = 4,
159 .sample_times = (unsigned int []){ 125, 250, 500, 1000 },
160 .resolutions = (u8 []) {9, 10, 11, 12 },
161 },
162 [ds75] = {
163 .clr_mask = 3 << 5,
164 .set_mask = 2 << 5, /* 11-bit mode */
165 .default_resolution = 11,
166 .default_sample_time = 600,
167 .num_sample_times = 4,
168 .sample_times = (unsigned int []){ 150, 300, 600, 1200 },
169 .resolutions = (u8 []) {9, 10, 11, 12 },
170 },
171 [stds75] = {
172 .clr_mask = 3 << 5,
173 .set_mask = 2 << 5, /* 11-bit mode */
174 .default_resolution = 11,
175 .default_sample_time = 600,
176 .num_sample_times = 4,
177 .sample_times = (unsigned int []){ 150, 300, 600, 1200 },
178 .resolutions = (u8 []) {9, 10, 11, 12 },
179 },
180 [stlm75] = {
181 .default_resolution = 9,
182 .default_sample_time = MSEC_PER_SEC / 6,
183 },
184 [ds7505] = {
185 .set_mask = 3 << 5, /* 12-bit mode*/
186 .default_resolution = 12,
187 .default_sample_time = 200,
188 .num_sample_times = 4,
189 .sample_times = (unsigned int []){ 25, 50, 100, 200 },
190 .resolutions = (u8 []) {9, 10, 11, 12 },
191 },
192 [g751] = {
193 .default_resolution = 9,
194 .default_sample_time = MSEC_PER_SEC / 10,
195 },
196 [lm75] = {
197 .default_resolution = 9,
198 .default_sample_time = MSEC_PER_SEC / 10,
199 },
200 [lm75a] = {
201 .default_resolution = 9,
202 .default_sample_time = MSEC_PER_SEC / 10,
203 },
204 [lm75b] = {
205 .default_resolution = 11,
206 .default_sample_time = MSEC_PER_SEC / 10,
207 },
208 [max6625] = {
209 .default_resolution = 9,
210 .default_sample_time = MSEC_PER_SEC / 7,
211 },
212 [max6626] = {
213 .default_resolution = 12,
214 .default_sample_time = MSEC_PER_SEC / 7,
215 .resolution_limits = 9,
216 },
217 [max31725] = {
218 .default_resolution = 16,
219 .default_sample_time = MSEC_PER_SEC / 20,
220 },
221 [tcn75] = {
222 .default_resolution = 9,
223 .default_sample_time = MSEC_PER_SEC / 18,
224 },
225 [pct2075] = {
226 .default_resolution = 11,
227 .default_sample_time = MSEC_PER_SEC / 10,
228 .num_sample_times = 31,
229 .sample_times = (unsigned int []){ 100, 200, 300, 400, 500, 600,
230 700, 800, 900, 1000, 1100, 1200, 1300, 1400, 1500, 1600, 1700,
231 1800, 1900, 2000, 2100, 2200, 2300, 2400, 2500, 2600, 2700,
232 2800, 2900, 3000, 3100 },
233 },
234 [mcp980x] = {
235 .set_mask = 3 << 5, /* 12-bit mode */
236 .clr_mask = 1 << 7, /* not one-shot mode */
237 .default_resolution = 12,
238 .resolution_limits = 9,
239 .default_sample_time = 240,
240 .num_sample_times = 4,
241 .sample_times = (unsigned int []){ 30, 60, 120, 240 },
242 .resolutions = (u8 []) {9, 10, 11, 12 },
243 },
244 [tmp100] = {
245 .set_mask = 3 << 5, /* 12-bit mode */
246 .clr_mask = 1 << 7, /* not one-shot mode */
247 .default_resolution = 12,
248 .default_sample_time = 320,
249 .num_sample_times = 4,
250 .sample_times = (unsigned int []){ 40, 80, 160, 320 },
251 .resolutions = (u8 []) {9, 10, 11, 12 },
252 },
253 [tmp101] = {
254 .set_mask = 3 << 5, /* 12-bit mode */
255 .clr_mask = 1 << 7, /* not one-shot mode */
256 .default_resolution = 12,
257 .default_sample_time = 320,
258 .num_sample_times = 4,
259 .sample_times = (unsigned int []){ 40, 80, 160, 320 },
260 .resolutions = (u8 []) {9, 10, 11, 12 },
261 },
262 [tmp105] = {
263 .set_mask = 3 << 5, /* 12-bit mode */
264 .clr_mask = 1 << 7, /* not one-shot mode*/
265 .default_resolution = 12,
266 .default_sample_time = 220,
267 .num_sample_times = 4,
268 .sample_times = (unsigned int []){ 28, 55, 110, 220 },
269 .resolutions = (u8 []) {9, 10, 11, 12 },
270 },
271 [tmp112] = {
272 .config_reg_16bits = true,
273 .set_mask = 0x60C0, /* 12-bit mode, 8 samples / second */
274 .clr_mask = 1 << 15, /* no one-shot mode*/
275 .default_resolution = 12,
276 .default_sample_time = 125,
277 .num_sample_times = 4,
278 .sample_times = (unsigned int []){ 125, 250, 1000, 4000 },
279 },
280 [tmp175] = {
281 .set_mask = 3 << 5, /* 12-bit mode */
282 .clr_mask = 1 << 7, /* not one-shot mode*/
283 .default_resolution = 12,
284 .default_sample_time = 220,
285 .num_sample_times = 4,
286 .sample_times = (unsigned int []){ 28, 55, 110, 220 },
287 .resolutions = (u8 []) {9, 10, 11, 12 },
288 },
289 [tmp275] = {
290 .set_mask = 3 << 5, /* 12-bit mode */
291 .clr_mask = 1 << 7, /* not one-shot mode*/
292 .default_resolution = 12,
293 .default_sample_time = 220,
294 .num_sample_times = 4,
295 .sample_times = (unsigned int []){ 28, 55, 110, 220 },
296 .resolutions = (u8 []) {9, 10, 11, 12 },
297 },
298 [tmp75] = {
299 .set_mask = 3 << 5, /* 12-bit mode */
300 .clr_mask = 1 << 7, /* not one-shot mode*/
301 .default_resolution = 12,
302 .default_sample_time = 220,
303 .num_sample_times = 4,
304 .sample_times = (unsigned int []){ 28, 55, 110, 220 },
305 .resolutions = (u8 []) {9, 10, 11, 12 },
306 },
307 [tmp75b] = { /* not one-shot mode, Conversion rate 37Hz */
308 .clr_mask = 1 << 7 | 3 << 5,
309 .default_resolution = 12,
310 .default_sample_time = MSEC_PER_SEC / 37,
311 .sample_times = (unsigned int []){ MSEC_PER_SEC / 37,
312 MSEC_PER_SEC / 18,
313 MSEC_PER_SEC / 9, MSEC_PER_SEC / 4 },
314 .num_sample_times = 4,
315 },
316 [tmp75c] = {
317 .clr_mask = 1 << 5, /*not one-shot mode*/
318 .default_resolution = 12,
319 .default_sample_time = MSEC_PER_SEC / 12,
320 },
321 [tmp1075] = { /* not one-shot mode, 27.5 ms sample rate */
322 .clr_mask = 1 << 5 | 1 << 6 | 1 << 7,
323 .default_resolution = 12,
324 .default_sample_time = 28,
325 .num_sample_times = 4,
326 .sample_times = (unsigned int []){ 28, 55, 110, 220 },
327 }
328};
329
330static inline long lm75_reg_to_mc(s16 temp, u8 resolution)
331{
332 return ((temp >> (16 - resolution)) * 1000) >> (resolution - 8);
333}
334
335static int lm75_write_config(struct lm75_data *data, u16 set_mask,
336 u16 clr_mask)
337{
338 unsigned int value;
339
340 clr_mask |= LM75_SHUTDOWN << (8 * data->params->config_reg_16bits);
341 value = data->current_conf & ~clr_mask;
342 value |= set_mask;
343
344 if (data->current_conf != value) {
345 s32 err;
346 if (data->params->config_reg_16bits)
347 err = regmap_write(data->regmap, LM75_REG_CONF, value);
348 else
349 err = i2c_smbus_write_byte_data(data->client,
350 LM75_REG_CONF,
351 value);
352 if (err)
353 return err;
354 data->current_conf = value;
355 }
356 return 0;
357}
358
359static int lm75_read_config(struct lm75_data *data)
360{
361 int ret;
362 unsigned int status;
363
364 if (data->params->config_reg_16bits) {
365 ret = regmap_read(data->regmap, LM75_REG_CONF, &status);
366 return ret ? ret : status;
367 }
368
369 return i2c_smbus_read_byte_data(data->client, LM75_REG_CONF);
370}
371
372static irqreturn_t lm75_alarm_handler(int irq, void *private)
373{
374 struct device *hwmon_dev = private;
375
376 hwmon_notify_event(hwmon_dev, hwmon_temp, hwmon_temp_alarm, 0);
377 return IRQ_HANDLED;
378}
379
380static int lm75_read(struct device *dev, enum hwmon_sensor_types type,
381 u32 attr, int channel, long *val)
382{
383 struct lm75_data *data = dev_get_drvdata(dev);
384 unsigned int regval;
385 int err, reg;
386
387 switch (type) {
388 case hwmon_chip:
389 switch (attr) {
390 case hwmon_chip_update_interval:
391 *val = data->sample_time;
392 break;
393 default:
394 return -EINVAL;
395 }
396 break;
397 case hwmon_temp:
398 switch (attr) {
399 case hwmon_temp_input:
400 reg = LM75_REG_TEMP;
401 break;
402 case hwmon_temp_max:
403 reg = LM75_REG_MAX;
404 break;
405 case hwmon_temp_max_hyst:
406 reg = LM75_REG_HYST;
407 break;
408 case hwmon_temp_alarm:
409 reg = LM75_REG_CONF;
410 break;
411 default:
412 return -EINVAL;
413 }
414 err = regmap_read(data->regmap, reg, ®val);
415 if (err < 0)
416 return err;
417
418 if (attr == hwmon_temp_alarm) {
419 switch (data->kind) {
420 case as6200:
421 *val = (regval >> 5) & 0x1;
422 break;
423 default:
424 return -EINVAL;
425 }
426 } else {
427 *val = lm75_reg_to_mc(regval, data->resolution);
428 }
429 break;
430 default:
431 return -EINVAL;
432 }
433 return 0;
434}
435
436static int lm75_write_temp(struct device *dev, u32 attr, long temp)
437{
438 struct lm75_data *data = dev_get_drvdata(dev);
439 u8 resolution;
440 int reg;
441
442 switch (attr) {
443 case hwmon_temp_max:
444 reg = LM75_REG_MAX;
445 break;
446 case hwmon_temp_max_hyst:
447 reg = LM75_REG_HYST;
448 break;
449 default:
450 return -EINVAL;
451 }
452
453 /*
454 * Resolution of limit registers is assumed to be the same as the
455 * temperature input register resolution unless given explicitly.
456 */
457 if (data->params->resolution_limits)
458 resolution = data->params->resolution_limits;
459 else
460 resolution = data->resolution;
461
462 temp = clamp_val(temp, LM75_TEMP_MIN, LM75_TEMP_MAX);
463 temp = DIV_ROUND_CLOSEST(temp << (resolution - 8),
464 1000) << (16 - resolution);
465
466 return regmap_write(data->regmap, reg, (u16)temp);
467}
468
469static int lm75_update_interval(struct device *dev, long val)
470{
471 struct lm75_data *data = dev_get_drvdata(dev);
472 unsigned int reg;
473 u8 index;
474 s32 err;
475
476 index = find_closest(val, data->params->sample_times,
477 (int)data->params->num_sample_times);
478
479 switch (data->kind) {
480 default:
481 err = lm75_write_config(data, lm75_sample_set_masks[index],
482 LM75_SAMPLE_CLEAR_MASK);
483 if (err)
484 return err;
485
486 data->sample_time = data->params->sample_times[index];
487 if (data->params->resolutions)
488 data->resolution = data->params->resolutions[index];
489 break;
490 case tmp112:
491 case as6200:
492 err = regmap_read(data->regmap, LM75_REG_CONF, ®);
493 if (err < 0)
494 return err;
495 reg &= ~0x00c0;
496 reg |= (3 - index) << 6;
497 err = regmap_write(data->regmap, LM75_REG_CONF, reg);
498 if (err < 0)
499 return err;
500 data->sample_time = data->params->sample_times[index];
501 break;
502 case pct2075:
503 err = i2c_smbus_write_byte_data(data->client, PCT2075_REG_IDLE,
504 index + 1);
505 if (err)
506 return err;
507 data->sample_time = data->params->sample_times[index];
508 break;
509 }
510 return 0;
511}
512
513static int lm75_write_chip(struct device *dev, u32 attr, long val)
514{
515 switch (attr) {
516 case hwmon_chip_update_interval:
517 return lm75_update_interval(dev, val);
518 default:
519 return -EINVAL;
520 }
521 return 0;
522}
523
524static int lm75_write(struct device *dev, enum hwmon_sensor_types type,
525 u32 attr, int channel, long val)
526{
527 switch (type) {
528 case hwmon_chip:
529 return lm75_write_chip(dev, attr, val);
530 case hwmon_temp:
531 return lm75_write_temp(dev, attr, val);
532 default:
533 return -EINVAL;
534 }
535 return 0;
536}
537
538static umode_t lm75_is_visible(const void *data, enum hwmon_sensor_types type,
539 u32 attr, int channel)
540{
541 const struct lm75_data *config_data = data;
542
543 switch (type) {
544 case hwmon_chip:
545 switch (attr) {
546 case hwmon_chip_update_interval:
547 if (config_data->params->num_sample_times > 1)
548 return 0644;
549 return 0444;
550 }
551 break;
552 case hwmon_temp:
553 switch (attr) {
554 case hwmon_temp_input:
555 return 0444;
556 case hwmon_temp_max:
557 case hwmon_temp_max_hyst:
558 return 0644;
559 case hwmon_temp_alarm:
560 if (config_data->params->alarm)
561 return 0444;
562 break;
563 }
564 break;
565 default:
566 break;
567 }
568 return 0;
569}
570
571static const struct hwmon_channel_info * const lm75_info[] = {
572 HWMON_CHANNEL_INFO(chip,
573 HWMON_C_REGISTER_TZ | HWMON_C_UPDATE_INTERVAL),
574 HWMON_CHANNEL_INFO(temp,
575 HWMON_T_INPUT | HWMON_T_MAX | HWMON_T_MAX_HYST |
576 HWMON_T_ALARM),
577 NULL
578};
579
580static const struct hwmon_ops lm75_hwmon_ops = {
581 .is_visible = lm75_is_visible,
582 .read = lm75_read,
583 .write = lm75_write,
584};
585
586static const struct hwmon_chip_info lm75_chip_info = {
587 .ops = &lm75_hwmon_ops,
588 .info = lm75_info,
589};
590
591static bool lm75_is_writeable_reg(struct device *dev, unsigned int reg)
592{
593 return reg != LM75_REG_TEMP;
594}
595
596static bool lm75_is_volatile_reg(struct device *dev, unsigned int reg)
597{
598 return reg == LM75_REG_TEMP || reg == LM75_REG_CONF;
599}
600
601static const struct regmap_config lm75_regmap_config = {
602 .reg_bits = 8,
603 .val_bits = 16,
604 .max_register = PCT2075_REG_IDLE,
605 .writeable_reg = lm75_is_writeable_reg,
606 .volatile_reg = lm75_is_volatile_reg,
607 .val_format_endian = REGMAP_ENDIAN_BIG,
608 .cache_type = REGCACHE_MAPLE,
609 .use_single_read = true,
610 .use_single_write = true,
611};
612
613static void lm75_disable_regulator(void *data)
614{
615 struct lm75_data *lm75 = data;
616
617 regulator_disable(lm75->vs);
618}
619
620static void lm75_remove(void *data)
621{
622 struct lm75_data *lm75 = data;
623 struct i2c_client *client = lm75->client;
624
625 i2c_smbus_write_byte_data(client, LM75_REG_CONF, lm75->orig_conf);
626}
627
628static const struct i2c_device_id lm75_ids[];
629
630static int lm75_probe(struct i2c_client *client)
631{
632 struct device *dev = &client->dev;
633 struct device *hwmon_dev;
634 struct lm75_data *data;
635 int status, err;
636 enum lm75_type kind;
637
638 if (client->dev.of_node)
639 kind = (uintptr_t)of_device_get_match_data(&client->dev);
640 else
641 kind = i2c_match_id(lm75_ids, client)->driver_data;
642
643 if (!i2c_check_functionality(client->adapter,
644 I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA))
645 return -EIO;
646
647 data = devm_kzalloc(dev, sizeof(struct lm75_data), GFP_KERNEL);
648 if (!data)
649 return -ENOMEM;
650
651 data->client = client;
652 data->kind = kind;
653
654 data->vs = devm_regulator_get(dev, "vs");
655 if (IS_ERR(data->vs))
656 return PTR_ERR(data->vs);
657
658 data->regmap = devm_regmap_init_i2c(client, &lm75_regmap_config);
659 if (IS_ERR(data->regmap))
660 return PTR_ERR(data->regmap);
661
662 /* Set to LM75 resolution (9 bits, 1/2 degree C) and range.
663 * Then tweak to be more precise when appropriate.
664 */
665
666 data->params = &device_params[data->kind];
667
668 /* Save default sample time and resolution*/
669 data->sample_time = data->params->default_sample_time;
670 data->resolution = data->params->default_resolution;
671
672 /* Enable the power */
673 err = regulator_enable(data->vs);
674 if (err) {
675 dev_err(dev, "failed to enable regulator: %d\n", err);
676 return err;
677 }
678
679 err = devm_add_action_or_reset(dev, lm75_disable_regulator, data);
680 if (err)
681 return err;
682
683 /* Cache original configuration */
684 status = lm75_read_config(data);
685 if (status < 0) {
686 dev_dbg(dev, "Can't read config? %d\n", status);
687 return status;
688 }
689 data->orig_conf = status;
690 data->current_conf = status;
691
692 err = lm75_write_config(data, data->params->set_mask,
693 data->params->clr_mask);
694 if (err)
695 return err;
696
697 err = devm_add_action_or_reset(dev, lm75_remove, data);
698 if (err)
699 return err;
700
701 hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name,
702 data, &lm75_chip_info,
703 NULL);
704 if (IS_ERR(hwmon_dev))
705 return PTR_ERR(hwmon_dev);
706
707 if (client->irq) {
708 if (data->params->alarm) {
709 err = devm_request_threaded_irq(dev,
710 client->irq,
711 NULL,
712 &lm75_alarm_handler,
713 IRQF_ONESHOT,
714 client->name,
715 hwmon_dev);
716 if (err)
717 return err;
718 } else {
719 /* alarm is only supported for chips with alarm bit */
720 dev_err(dev, "alarm interrupt is not supported\n");
721 }
722 }
723
724 dev_info(dev, "%s: sensor '%s'\n", dev_name(hwmon_dev), client->name);
725
726 return 0;
727}
728
729static const struct i2c_device_id lm75_ids[] = {
730 { "adt75", adt75, },
731 { "as6200", as6200, },
732 { "at30ts74", at30ts74, },
733 { "ds1775", ds1775, },
734 { "ds75", ds75, },
735 { "ds7505", ds7505, },
736 { "g751", g751, },
737 { "lm75", lm75, },
738 { "lm75a", lm75a, },
739 { "lm75b", lm75b, },
740 { "max6625", max6625, },
741 { "max6626", max6626, },
742 { "max31725", max31725, },
743 { "max31726", max31725, },
744 { "mcp980x", mcp980x, },
745 { "pct2075", pct2075, },
746 { "stds75", stds75, },
747 { "stlm75", stlm75, },
748 { "tcn75", tcn75, },
749 { "tmp100", tmp100, },
750 { "tmp101", tmp101, },
751 { "tmp105", tmp105, },
752 { "tmp112", tmp112, },
753 { "tmp175", tmp175, },
754 { "tmp275", tmp275, },
755 { "tmp75", tmp75, },
756 { "tmp75b", tmp75b, },
757 { "tmp75c", tmp75c, },
758 { "tmp1075", tmp1075, },
759 { /* LIST END */ }
760};
761MODULE_DEVICE_TABLE(i2c, lm75_ids);
762
763static const struct of_device_id __maybe_unused lm75_of_match[] = {
764 {
765 .compatible = "adi,adt75",
766 .data = (void *)adt75
767 },
768 {
769 .compatible = "ams,as6200",
770 .data = (void *)as6200
771 },
772 {
773 .compatible = "atmel,at30ts74",
774 .data = (void *)at30ts74
775 },
776 {
777 .compatible = "dallas,ds1775",
778 .data = (void *)ds1775
779 },
780 {
781 .compatible = "dallas,ds75",
782 .data = (void *)ds75
783 },
784 {
785 .compatible = "dallas,ds7505",
786 .data = (void *)ds7505
787 },
788 {
789 .compatible = "gmt,g751",
790 .data = (void *)g751
791 },
792 {
793 .compatible = "national,lm75",
794 .data = (void *)lm75
795 },
796 {
797 .compatible = "national,lm75a",
798 .data = (void *)lm75a
799 },
800 {
801 .compatible = "national,lm75b",
802 .data = (void *)lm75b
803 },
804 {
805 .compatible = "maxim,max6625",
806 .data = (void *)max6625
807 },
808 {
809 .compatible = "maxim,max6626",
810 .data = (void *)max6626
811 },
812 {
813 .compatible = "maxim,max31725",
814 .data = (void *)max31725
815 },
816 {
817 .compatible = "maxim,max31726",
818 .data = (void *)max31725
819 },
820 {
821 .compatible = "maxim,mcp980x",
822 .data = (void *)mcp980x
823 },
824 {
825 .compatible = "nxp,pct2075",
826 .data = (void *)pct2075
827 },
828 {
829 .compatible = "st,stds75",
830 .data = (void *)stds75
831 },
832 {
833 .compatible = "st,stlm75",
834 .data = (void *)stlm75
835 },
836 {
837 .compatible = "microchip,tcn75",
838 .data = (void *)tcn75
839 },
840 {
841 .compatible = "ti,tmp100",
842 .data = (void *)tmp100
843 },
844 {
845 .compatible = "ti,tmp101",
846 .data = (void *)tmp101
847 },
848 {
849 .compatible = "ti,tmp105",
850 .data = (void *)tmp105
851 },
852 {
853 .compatible = "ti,tmp112",
854 .data = (void *)tmp112
855 },
856 {
857 .compatible = "ti,tmp175",
858 .data = (void *)tmp175
859 },
860 {
861 .compatible = "ti,tmp275",
862 .data = (void *)tmp275
863 },
864 {
865 .compatible = "ti,tmp75",
866 .data = (void *)tmp75
867 },
868 {
869 .compatible = "ti,tmp75b",
870 .data = (void *)tmp75b
871 },
872 {
873 .compatible = "ti,tmp75c",
874 .data = (void *)tmp75c
875 },
876 {
877 .compatible = "ti,tmp1075",
878 .data = (void *)tmp1075
879 },
880 { },
881};
882MODULE_DEVICE_TABLE(of, lm75_of_match);
883
884#define LM75A_ID 0xA1
885
886/* Return 0 if detection is successful, -ENODEV otherwise */
887static int lm75_detect(struct i2c_client *new_client,
888 struct i2c_board_info *info)
889{
890 struct i2c_adapter *adapter = new_client->adapter;
891 int i;
892 int conf, hyst, os;
893 bool is_lm75a = 0;
894
895 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA |
896 I2C_FUNC_SMBUS_WORD_DATA))
897 return -ENODEV;
898
899 /*
900 * Now, we do the remaining detection. There is no identification-
901 * dedicated register so we have to rely on several tricks:
902 * unused bits, registers cycling over 8-address boundaries,
903 * addresses 0x04-0x07 returning the last read value.
904 * The cycling+unused addresses combination is not tested,
905 * since it would significantly slow the detection down and would
906 * hardly add any value.
907 *
908 * The National Semiconductor LM75A is different than earlier
909 * LM75s. It has an ID byte of 0xaX (where X is the chip
910 * revision, with 1 being the only revision in existence) in
911 * register 7, and unused registers return 0xff rather than the
912 * last read value.
913 *
914 * Note that this function only detects the original National
915 * Semiconductor LM75 and the LM75A. Clones from other vendors
916 * aren't detected, on purpose, because they are typically never
917 * found on PC hardware. They are found on embedded designs where
918 * they can be instantiated explicitly so detection is not needed.
919 * The absence of identification registers on all these clones
920 * would make their exhaustive detection very difficult and weak,
921 * and odds are that the driver would bind to unsupported devices.
922 */
923
924 /* Unused bits */
925 conf = i2c_smbus_read_byte_data(new_client, 1);
926 if (conf & 0xe0)
927 return -ENODEV;
928
929 /* First check for LM75A */
930 if (i2c_smbus_read_byte_data(new_client, 7) == LM75A_ID) {
931 /*
932 * LM75A returns 0xff on unused registers so
933 * just to be sure we check for that too.
934 */
935 if (i2c_smbus_read_byte_data(new_client, 4) != 0xff
936 || i2c_smbus_read_byte_data(new_client, 5) != 0xff
937 || i2c_smbus_read_byte_data(new_client, 6) != 0xff)
938 return -ENODEV;
939 is_lm75a = 1;
940 hyst = i2c_smbus_read_byte_data(new_client, 2);
941 os = i2c_smbus_read_byte_data(new_client, 3);
942 } else { /* Traditional style LM75 detection */
943 /* Unused addresses */
944 hyst = i2c_smbus_read_byte_data(new_client, 2);
945 if (i2c_smbus_read_byte_data(new_client, 4) != hyst
946 || i2c_smbus_read_byte_data(new_client, 5) != hyst
947 || i2c_smbus_read_byte_data(new_client, 6) != hyst
948 || i2c_smbus_read_byte_data(new_client, 7) != hyst)
949 return -ENODEV;
950 os = i2c_smbus_read_byte_data(new_client, 3);
951 if (i2c_smbus_read_byte_data(new_client, 4) != os
952 || i2c_smbus_read_byte_data(new_client, 5) != os
953 || i2c_smbus_read_byte_data(new_client, 6) != os
954 || i2c_smbus_read_byte_data(new_client, 7) != os)
955 return -ENODEV;
956 }
957 /*
958 * It is very unlikely that this is a LM75 if both
959 * hysteresis and temperature limit registers are 0.
960 */
961 if (hyst == 0 && os == 0)
962 return -ENODEV;
963
964 /* Addresses cycling */
965 for (i = 8; i <= 248; i += 40) {
966 if (i2c_smbus_read_byte_data(new_client, i + 1) != conf
967 || i2c_smbus_read_byte_data(new_client, i + 2) != hyst
968 || i2c_smbus_read_byte_data(new_client, i + 3) != os)
969 return -ENODEV;
970 if (is_lm75a && i2c_smbus_read_byte_data(new_client, i + 7)
971 != LM75A_ID)
972 return -ENODEV;
973 }
974
975 strscpy(info->type, is_lm75a ? "lm75a" : "lm75", I2C_NAME_SIZE);
976
977 return 0;
978}
979
980#ifdef CONFIG_PM
981static int lm75_suspend(struct device *dev)
982{
983 int status;
984 struct i2c_client *client = to_i2c_client(dev);
985
986 status = i2c_smbus_read_byte_data(client, LM75_REG_CONF);
987 if (status < 0) {
988 dev_dbg(&client->dev, "Can't read config? %d\n", status);
989 return status;
990 }
991 status = status | LM75_SHUTDOWN;
992 i2c_smbus_write_byte_data(client, LM75_REG_CONF, status);
993 return 0;
994}
995
996static int lm75_resume(struct device *dev)
997{
998 int status;
999 struct i2c_client *client = to_i2c_client(dev);
1000
1001 status = i2c_smbus_read_byte_data(client, LM75_REG_CONF);
1002 if (status < 0) {
1003 dev_dbg(&client->dev, "Can't read config? %d\n", status);
1004 return status;
1005 }
1006 status = status & ~LM75_SHUTDOWN;
1007 i2c_smbus_write_byte_data(client, LM75_REG_CONF, status);
1008 return 0;
1009}
1010
1011static const struct dev_pm_ops lm75_dev_pm_ops = {
1012 .suspend = lm75_suspend,
1013 .resume = lm75_resume,
1014};
1015#define LM75_DEV_PM_OPS (&lm75_dev_pm_ops)
1016#else
1017#define LM75_DEV_PM_OPS NULL
1018#endif /* CONFIG_PM */
1019
1020static struct i2c_driver lm75_driver = {
1021 .class = I2C_CLASS_HWMON,
1022 .driver = {
1023 .name = "lm75",
1024 .of_match_table = of_match_ptr(lm75_of_match),
1025 .pm = LM75_DEV_PM_OPS,
1026 },
1027 .probe = lm75_probe,
1028 .id_table = lm75_ids,
1029 .detect = lm75_detect,
1030 .address_list = normal_i2c,
1031};
1032
1033module_i2c_driver(lm75_driver);
1034
1035MODULE_AUTHOR("Frodo Looijaard <frodol@dds.nl>");
1036MODULE_DESCRIPTION("LM75 driver");
1037MODULE_LICENSE("GPL");
1/*
2 * lm75.c - Part of lm_sensors, Linux kernel modules for hardware
3 * monitoring
4 * Copyright (c) 1998, 1999 Frodo Looijaard <frodol@dds.nl>
5 *
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2 of the License, or
9 * (at your option) any later version.
10 *
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
15 *
16 * You should have received a copy of the GNU General Public License
17 * along with this program; if not, write to the Free Software
18 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
19 */
20
21#include <linux/module.h>
22#include <linux/init.h>
23#include <linux/slab.h>
24#include <linux/jiffies.h>
25#include <linux/i2c.h>
26#include <linux/hwmon.h>
27#include <linux/hwmon-sysfs.h>
28#include <linux/err.h>
29#include <linux/of_device.h>
30#include <linux/of.h>
31#include <linux/regmap.h>
32#include "lm75.h"
33
34
35/*
36 * This driver handles the LM75 and compatible digital temperature sensors.
37 */
38
39enum lm75_type { /* keep sorted in alphabetical order */
40 adt75,
41 ds1775,
42 ds75,
43 ds7505,
44 g751,
45 lm75,
46 lm75a,
47 lm75b,
48 max6625,
49 max6626,
50 mcp980x,
51 stds75,
52 tcn75,
53 tmp100,
54 tmp101,
55 tmp105,
56 tmp112,
57 tmp175,
58 tmp275,
59 tmp75,
60 tmp75c,
61};
62
63/* Addresses scanned */
64static const unsigned short normal_i2c[] = { 0x48, 0x49, 0x4a, 0x4b, 0x4c,
65 0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
66
67
68/* The LM75 registers */
69#define LM75_REG_TEMP 0x00
70#define LM75_REG_CONF 0x01
71#define LM75_REG_HYST 0x02
72#define LM75_REG_MAX 0x03
73
74/* Each client has this additional data */
75struct lm75_data {
76 struct i2c_client *client;
77 struct regmap *regmap;
78 u8 orig_conf;
79 u8 resolution; /* In bits, between 9 and 12 */
80 u8 resolution_limits;
81 unsigned int sample_time; /* In ms */
82};
83
84/*-----------------------------------------------------------------------*/
85
86static inline long lm75_reg_to_mc(s16 temp, u8 resolution)
87{
88 return ((temp >> (16 - resolution)) * 1000) >> (resolution - 8);
89}
90
91static int lm75_read(struct device *dev, enum hwmon_sensor_types type,
92 u32 attr, int channel, long *val)
93{
94 struct lm75_data *data = dev_get_drvdata(dev);
95 unsigned int regval;
96 int err, reg;
97
98 switch (type) {
99 case hwmon_chip:
100 switch (attr) {
101 case hwmon_chip_update_interval:
102 *val = data->sample_time;
103 break;
104 default:
105 return -EINVAL;
106 }
107 break;
108 case hwmon_temp:
109 switch (attr) {
110 case hwmon_temp_input:
111 reg = LM75_REG_TEMP;
112 break;
113 case hwmon_temp_max:
114 reg = LM75_REG_MAX;
115 break;
116 case hwmon_temp_max_hyst:
117 reg = LM75_REG_HYST;
118 break;
119 default:
120 return -EINVAL;
121 }
122 err = regmap_read(data->regmap, reg, ®val);
123 if (err < 0)
124 return err;
125
126 *val = lm75_reg_to_mc(regval, data->resolution);
127 break;
128 default:
129 return -EINVAL;
130 }
131 return 0;
132}
133
134static int lm75_write(struct device *dev, enum hwmon_sensor_types type,
135 u32 attr, int channel, long temp)
136{
137 struct lm75_data *data = dev_get_drvdata(dev);
138 u8 resolution;
139 int reg;
140
141 if (type != hwmon_temp)
142 return -EINVAL;
143
144 switch (attr) {
145 case hwmon_temp_max:
146 reg = LM75_REG_MAX;
147 break;
148 case hwmon_temp_max_hyst:
149 reg = LM75_REG_HYST;
150 break;
151 default:
152 return -EINVAL;
153 }
154
155 /*
156 * Resolution of limit registers is assumed to be the same as the
157 * temperature input register resolution unless given explicitly.
158 */
159 if (data->resolution_limits)
160 resolution = data->resolution_limits;
161 else
162 resolution = data->resolution;
163
164 temp = clamp_val(temp, LM75_TEMP_MIN, LM75_TEMP_MAX);
165 temp = DIV_ROUND_CLOSEST(temp << (resolution - 8),
166 1000) << (16 - resolution);
167
168 return regmap_write(data->regmap, reg, temp);
169}
170
171static umode_t lm75_is_visible(const void *data, enum hwmon_sensor_types type,
172 u32 attr, int channel)
173{
174 switch (type) {
175 case hwmon_chip:
176 switch (attr) {
177 case hwmon_chip_update_interval:
178 return S_IRUGO;
179 }
180 break;
181 case hwmon_temp:
182 switch (attr) {
183 case hwmon_temp_input:
184 return S_IRUGO;
185 case hwmon_temp_max:
186 case hwmon_temp_max_hyst:
187 return S_IRUGO | S_IWUSR;
188 }
189 break;
190 default:
191 break;
192 }
193 return 0;
194}
195
196/*-----------------------------------------------------------------------*/
197
198/* device probe and removal */
199
200/* chip configuration */
201
202static const u32 lm75_chip_config[] = {
203 HWMON_C_REGISTER_TZ | HWMON_C_UPDATE_INTERVAL,
204 0
205};
206
207static const struct hwmon_channel_info lm75_chip = {
208 .type = hwmon_chip,
209 .config = lm75_chip_config,
210};
211
212static const u32 lm75_temp_config[] = {
213 HWMON_T_INPUT | HWMON_T_MAX | HWMON_T_MAX_HYST,
214 0
215};
216
217static const struct hwmon_channel_info lm75_temp = {
218 .type = hwmon_temp,
219 .config = lm75_temp_config,
220};
221
222static const struct hwmon_channel_info *lm75_info[] = {
223 &lm75_chip,
224 &lm75_temp,
225 NULL
226};
227
228static const struct hwmon_ops lm75_hwmon_ops = {
229 .is_visible = lm75_is_visible,
230 .read = lm75_read,
231 .write = lm75_write,
232};
233
234static const struct hwmon_chip_info lm75_chip_info = {
235 .ops = &lm75_hwmon_ops,
236 .info = lm75_info,
237};
238
239static bool lm75_is_writeable_reg(struct device *dev, unsigned int reg)
240{
241 return reg != LM75_REG_TEMP;
242}
243
244static bool lm75_is_volatile_reg(struct device *dev, unsigned int reg)
245{
246 return reg == LM75_REG_TEMP;
247}
248
249static const struct regmap_config lm75_regmap_config = {
250 .reg_bits = 8,
251 .val_bits = 16,
252 .max_register = LM75_REG_MAX,
253 .writeable_reg = lm75_is_writeable_reg,
254 .volatile_reg = lm75_is_volatile_reg,
255 .val_format_endian = REGMAP_ENDIAN_BIG,
256 .cache_type = REGCACHE_RBTREE,
257 .use_single_rw = true,
258};
259
260static void lm75_remove(void *data)
261{
262 struct lm75_data *lm75 = data;
263 struct i2c_client *client = lm75->client;
264
265 i2c_smbus_write_byte_data(client, LM75_REG_CONF, lm75->orig_conf);
266}
267
268static int
269lm75_probe(struct i2c_client *client, const struct i2c_device_id *id)
270{
271 struct device *dev = &client->dev;
272 struct device *hwmon_dev;
273 struct lm75_data *data;
274 int status, err;
275 u8 set_mask, clr_mask;
276 int new;
277 enum lm75_type kind;
278
279 if (client->dev.of_node)
280 kind = (enum lm75_type)of_device_get_match_data(&client->dev);
281 else
282 kind = id->driver_data;
283
284 if (!i2c_check_functionality(client->adapter,
285 I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA))
286 return -EIO;
287
288 data = devm_kzalloc(dev, sizeof(struct lm75_data), GFP_KERNEL);
289 if (!data)
290 return -ENOMEM;
291
292 data->client = client;
293
294 data->regmap = devm_regmap_init_i2c(client, &lm75_regmap_config);
295 if (IS_ERR(data->regmap))
296 return PTR_ERR(data->regmap);
297
298 /* Set to LM75 resolution (9 bits, 1/2 degree C) and range.
299 * Then tweak to be more precise when appropriate.
300 */
301 set_mask = 0;
302 clr_mask = LM75_SHUTDOWN; /* continuous conversions */
303
304 switch (kind) {
305 case adt75:
306 clr_mask |= 1 << 5; /* not one-shot mode */
307 data->resolution = 12;
308 data->sample_time = MSEC_PER_SEC / 8;
309 break;
310 case ds1775:
311 case ds75:
312 case stds75:
313 clr_mask |= 3 << 5;
314 set_mask |= 2 << 5; /* 11-bit mode */
315 data->resolution = 11;
316 data->sample_time = MSEC_PER_SEC;
317 break;
318 case ds7505:
319 set_mask |= 3 << 5; /* 12-bit mode */
320 data->resolution = 12;
321 data->sample_time = MSEC_PER_SEC / 4;
322 break;
323 case g751:
324 case lm75:
325 case lm75a:
326 data->resolution = 9;
327 data->sample_time = MSEC_PER_SEC / 2;
328 break;
329 case lm75b:
330 data->resolution = 11;
331 data->sample_time = MSEC_PER_SEC / 4;
332 break;
333 case max6625:
334 data->resolution = 9;
335 data->sample_time = MSEC_PER_SEC / 4;
336 break;
337 case max6626:
338 data->resolution = 12;
339 data->resolution_limits = 9;
340 data->sample_time = MSEC_PER_SEC / 4;
341 break;
342 case tcn75:
343 data->resolution = 9;
344 data->sample_time = MSEC_PER_SEC / 8;
345 break;
346 case mcp980x:
347 data->resolution_limits = 9;
348 /* fall through */
349 case tmp100:
350 case tmp101:
351 set_mask |= 3 << 5; /* 12-bit mode */
352 data->resolution = 12;
353 data->sample_time = MSEC_PER_SEC;
354 clr_mask |= 1 << 7; /* not one-shot mode */
355 break;
356 case tmp112:
357 set_mask |= 3 << 5; /* 12-bit mode */
358 clr_mask |= 1 << 7; /* not one-shot mode */
359 data->resolution = 12;
360 data->sample_time = MSEC_PER_SEC / 4;
361 break;
362 case tmp105:
363 case tmp175:
364 case tmp275:
365 case tmp75:
366 set_mask |= 3 << 5; /* 12-bit mode */
367 clr_mask |= 1 << 7; /* not one-shot mode */
368 data->resolution = 12;
369 data->sample_time = MSEC_PER_SEC / 2;
370 break;
371 case tmp75c:
372 clr_mask |= 1 << 5; /* not one-shot mode */
373 data->resolution = 12;
374 data->sample_time = MSEC_PER_SEC / 4;
375 break;
376 }
377
378 /* configure as specified */
379 status = i2c_smbus_read_byte_data(client, LM75_REG_CONF);
380 if (status < 0) {
381 dev_dbg(dev, "Can't read config? %d\n", status);
382 return status;
383 }
384 data->orig_conf = status;
385 new = status & ~clr_mask;
386 new |= set_mask;
387 if (status != new)
388 i2c_smbus_write_byte_data(client, LM75_REG_CONF, new);
389
390 err = devm_add_action_or_reset(dev, lm75_remove, data);
391 if (err)
392 return err;
393
394 dev_dbg(dev, "Config %02x\n", new);
395
396 hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name,
397 data, &lm75_chip_info,
398 NULL);
399 if (IS_ERR(hwmon_dev))
400 return PTR_ERR(hwmon_dev);
401
402 dev_info(dev, "%s: sensor '%s'\n", dev_name(hwmon_dev), client->name);
403
404 return 0;
405}
406
407static const struct i2c_device_id lm75_ids[] = {
408 { "adt75", adt75, },
409 { "ds1775", ds1775, },
410 { "ds75", ds75, },
411 { "ds7505", ds7505, },
412 { "g751", g751, },
413 { "lm75", lm75, },
414 { "lm75a", lm75a, },
415 { "lm75b", lm75b, },
416 { "max6625", max6625, },
417 { "max6626", max6626, },
418 { "mcp980x", mcp980x, },
419 { "stds75", stds75, },
420 { "tcn75", tcn75, },
421 { "tmp100", tmp100, },
422 { "tmp101", tmp101, },
423 { "tmp105", tmp105, },
424 { "tmp112", tmp112, },
425 { "tmp175", tmp175, },
426 { "tmp275", tmp275, },
427 { "tmp75", tmp75, },
428 { "tmp75c", tmp75c, },
429 { /* LIST END */ }
430};
431MODULE_DEVICE_TABLE(i2c, lm75_ids);
432
433static const struct of_device_id lm75_of_match[] = {
434 {
435 .compatible = "adi,adt75",
436 .data = (void *)adt75
437 },
438 {
439 .compatible = "dallas,ds1775",
440 .data = (void *)ds1775
441 },
442 {
443 .compatible = "dallas,ds75",
444 .data = (void *)ds75
445 },
446 {
447 .compatible = "dallas,ds7505",
448 .data = (void *)ds7505
449 },
450 {
451 .compatible = "gmt,g751",
452 .data = (void *)g751
453 },
454 {
455 .compatible = "national,lm75",
456 .data = (void *)lm75
457 },
458 {
459 .compatible = "national,lm75a",
460 .data = (void *)lm75a
461 },
462 {
463 .compatible = "national,lm75b",
464 .data = (void *)lm75b
465 },
466 {
467 .compatible = "maxim,max6625",
468 .data = (void *)max6625
469 },
470 {
471 .compatible = "maxim,max6626",
472 .data = (void *)max6626
473 },
474 {
475 .compatible = "maxim,mcp980x",
476 .data = (void *)mcp980x
477 },
478 {
479 .compatible = "st,stds75",
480 .data = (void *)stds75
481 },
482 {
483 .compatible = "microchip,tcn75",
484 .data = (void *)tcn75
485 },
486 {
487 .compatible = "ti,tmp100",
488 .data = (void *)tmp100
489 },
490 {
491 .compatible = "ti,tmp101",
492 .data = (void *)tmp101
493 },
494 {
495 .compatible = "ti,tmp105",
496 .data = (void *)tmp105
497 },
498 {
499 .compatible = "ti,tmp112",
500 .data = (void *)tmp112
501 },
502 {
503 .compatible = "ti,tmp175",
504 .data = (void *)tmp175
505 },
506 {
507 .compatible = "ti,tmp275",
508 .data = (void *)tmp275
509 },
510 {
511 .compatible = "ti,tmp75",
512 .data = (void *)tmp75
513 },
514 {
515 .compatible = "ti,tmp75c",
516 .data = (void *)tmp75c
517 },
518 { },
519};
520MODULE_DEVICE_TABLE(of, lm75_of_match);
521
522#define LM75A_ID 0xA1
523
524/* Return 0 if detection is successful, -ENODEV otherwise */
525static int lm75_detect(struct i2c_client *new_client,
526 struct i2c_board_info *info)
527{
528 struct i2c_adapter *adapter = new_client->adapter;
529 int i;
530 int conf, hyst, os;
531 bool is_lm75a = 0;
532
533 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA |
534 I2C_FUNC_SMBUS_WORD_DATA))
535 return -ENODEV;
536
537 /*
538 * Now, we do the remaining detection. There is no identification-
539 * dedicated register so we have to rely on several tricks:
540 * unused bits, registers cycling over 8-address boundaries,
541 * addresses 0x04-0x07 returning the last read value.
542 * The cycling+unused addresses combination is not tested,
543 * since it would significantly slow the detection down and would
544 * hardly add any value.
545 *
546 * The National Semiconductor LM75A is different than earlier
547 * LM75s. It has an ID byte of 0xaX (where X is the chip
548 * revision, with 1 being the only revision in existence) in
549 * register 7, and unused registers return 0xff rather than the
550 * last read value.
551 *
552 * Note that this function only detects the original National
553 * Semiconductor LM75 and the LM75A. Clones from other vendors
554 * aren't detected, on purpose, because they are typically never
555 * found on PC hardware. They are found on embedded designs where
556 * they can be instantiated explicitly so detection is not needed.
557 * The absence of identification registers on all these clones
558 * would make their exhaustive detection very difficult and weak,
559 * and odds are that the driver would bind to unsupported devices.
560 */
561
562 /* Unused bits */
563 conf = i2c_smbus_read_byte_data(new_client, 1);
564 if (conf & 0xe0)
565 return -ENODEV;
566
567 /* First check for LM75A */
568 if (i2c_smbus_read_byte_data(new_client, 7) == LM75A_ID) {
569 /* LM75A returns 0xff on unused registers so
570 just to be sure we check for that too. */
571 if (i2c_smbus_read_byte_data(new_client, 4) != 0xff
572 || i2c_smbus_read_byte_data(new_client, 5) != 0xff
573 || i2c_smbus_read_byte_data(new_client, 6) != 0xff)
574 return -ENODEV;
575 is_lm75a = 1;
576 hyst = i2c_smbus_read_byte_data(new_client, 2);
577 os = i2c_smbus_read_byte_data(new_client, 3);
578 } else { /* Traditional style LM75 detection */
579 /* Unused addresses */
580 hyst = i2c_smbus_read_byte_data(new_client, 2);
581 if (i2c_smbus_read_byte_data(new_client, 4) != hyst
582 || i2c_smbus_read_byte_data(new_client, 5) != hyst
583 || i2c_smbus_read_byte_data(new_client, 6) != hyst
584 || i2c_smbus_read_byte_data(new_client, 7) != hyst)
585 return -ENODEV;
586 os = i2c_smbus_read_byte_data(new_client, 3);
587 if (i2c_smbus_read_byte_data(new_client, 4) != os
588 || i2c_smbus_read_byte_data(new_client, 5) != os
589 || i2c_smbus_read_byte_data(new_client, 6) != os
590 || i2c_smbus_read_byte_data(new_client, 7) != os)
591 return -ENODEV;
592 }
593 /*
594 * It is very unlikely that this is a LM75 if both
595 * hysteresis and temperature limit registers are 0.
596 */
597 if (hyst == 0 && os == 0)
598 return -ENODEV;
599
600 /* Addresses cycling */
601 for (i = 8; i <= 248; i += 40) {
602 if (i2c_smbus_read_byte_data(new_client, i + 1) != conf
603 || i2c_smbus_read_byte_data(new_client, i + 2) != hyst
604 || i2c_smbus_read_byte_data(new_client, i + 3) != os)
605 return -ENODEV;
606 if (is_lm75a && i2c_smbus_read_byte_data(new_client, i + 7)
607 != LM75A_ID)
608 return -ENODEV;
609 }
610
611 strlcpy(info->type, is_lm75a ? "lm75a" : "lm75", I2C_NAME_SIZE);
612
613 return 0;
614}
615
616#ifdef CONFIG_PM
617static int lm75_suspend(struct device *dev)
618{
619 int status;
620 struct i2c_client *client = to_i2c_client(dev);
621 status = i2c_smbus_read_byte_data(client, LM75_REG_CONF);
622 if (status < 0) {
623 dev_dbg(&client->dev, "Can't read config? %d\n", status);
624 return status;
625 }
626 status = status | LM75_SHUTDOWN;
627 i2c_smbus_write_byte_data(client, LM75_REG_CONF, status);
628 return 0;
629}
630
631static int lm75_resume(struct device *dev)
632{
633 int status;
634 struct i2c_client *client = to_i2c_client(dev);
635 status = i2c_smbus_read_byte_data(client, LM75_REG_CONF);
636 if (status < 0) {
637 dev_dbg(&client->dev, "Can't read config? %d\n", status);
638 return status;
639 }
640 status = status & ~LM75_SHUTDOWN;
641 i2c_smbus_write_byte_data(client, LM75_REG_CONF, status);
642 return 0;
643}
644
645static const struct dev_pm_ops lm75_dev_pm_ops = {
646 .suspend = lm75_suspend,
647 .resume = lm75_resume,
648};
649#define LM75_DEV_PM_OPS (&lm75_dev_pm_ops)
650#else
651#define LM75_DEV_PM_OPS NULL
652#endif /* CONFIG_PM */
653
654static struct i2c_driver lm75_driver = {
655 .class = I2C_CLASS_HWMON,
656 .driver = {
657 .name = "lm75",
658 .of_match_table = of_match_ptr(lm75_of_match),
659 .pm = LM75_DEV_PM_OPS,
660 },
661 .probe = lm75_probe,
662 .id_table = lm75_ids,
663 .detect = lm75_detect,
664 .address_list = normal_i2c,
665};
666
667module_i2c_driver(lm75_driver);
668
669MODULE_AUTHOR("Frodo Looijaard <frodol@dds.nl>");
670MODULE_DESCRIPTION("LM75 driver");
671MODULE_LICENSE("GPL");