Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Copyright (C) 2013 STMicroelectronics
4 *
5 * I2C master mode controller driver, used in STMicroelectronics devices.
6 *
7 * Author: Maxime Coquelin <maxime.coquelin@st.com>
8 */
9
10#include <linux/clk.h>
11#include <linux/delay.h>
12#include <linux/err.h>
13#include <linux/i2c.h>
14#include <linux/interrupt.h>
15#include <linux/io.h>
16#include <linux/module.h>
17#include <linux/of_address.h>
18#include <linux/of_irq.h>
19#include <linux/of.h>
20#include <linux/pinctrl/consumer.h>
21#include <linux/platform_device.h>
22
23/* SSC registers */
24#define SSC_BRG 0x000
25#define SSC_TBUF 0x004
26#define SSC_RBUF 0x008
27#define SSC_CTL 0x00C
28#define SSC_IEN 0x010
29#define SSC_STA 0x014
30#define SSC_I2C 0x018
31#define SSC_SLAD 0x01C
32#define SSC_REP_START_HOLD 0x020
33#define SSC_START_HOLD 0x024
34#define SSC_REP_START_SETUP 0x028
35#define SSC_DATA_SETUP 0x02C
36#define SSC_STOP_SETUP 0x030
37#define SSC_BUS_FREE 0x034
38#define SSC_TX_FSTAT 0x038
39#define SSC_RX_FSTAT 0x03C
40#define SSC_PRE_SCALER_BRG 0x040
41#define SSC_CLR 0x080
42#define SSC_NOISE_SUPP_WIDTH 0x100
43#define SSC_PRSCALER 0x104
44#define SSC_NOISE_SUPP_WIDTH_DATAOUT 0x108
45#define SSC_PRSCALER_DATAOUT 0x10c
46
47/* SSC Control */
48#define SSC_CTL_DATA_WIDTH_9 0x8
49#define SSC_CTL_DATA_WIDTH_MSK 0xf
50#define SSC_CTL_BM 0xf
51#define SSC_CTL_HB BIT(4)
52#define SSC_CTL_PH BIT(5)
53#define SSC_CTL_PO BIT(6)
54#define SSC_CTL_SR BIT(7)
55#define SSC_CTL_MS BIT(8)
56#define SSC_CTL_EN BIT(9)
57#define SSC_CTL_LPB BIT(10)
58#define SSC_CTL_EN_TX_FIFO BIT(11)
59#define SSC_CTL_EN_RX_FIFO BIT(12)
60#define SSC_CTL_EN_CLST_RX BIT(13)
61
62/* SSC Interrupt Enable */
63#define SSC_IEN_RIEN BIT(0)
64#define SSC_IEN_TIEN BIT(1)
65#define SSC_IEN_TEEN BIT(2)
66#define SSC_IEN_REEN BIT(3)
67#define SSC_IEN_PEEN BIT(4)
68#define SSC_IEN_AASEN BIT(6)
69#define SSC_IEN_STOPEN BIT(7)
70#define SSC_IEN_ARBLEN BIT(8)
71#define SSC_IEN_NACKEN BIT(10)
72#define SSC_IEN_REPSTRTEN BIT(11)
73#define SSC_IEN_TX_FIFO_HALF BIT(12)
74#define SSC_IEN_RX_FIFO_HALF_FULL BIT(14)
75
76/* SSC Status */
77#define SSC_STA_RIR BIT(0)
78#define SSC_STA_TIR BIT(1)
79#define SSC_STA_TE BIT(2)
80#define SSC_STA_RE BIT(3)
81#define SSC_STA_PE BIT(4)
82#define SSC_STA_CLST BIT(5)
83#define SSC_STA_AAS BIT(6)
84#define SSC_STA_STOP BIT(7)
85#define SSC_STA_ARBL BIT(8)
86#define SSC_STA_BUSY BIT(9)
87#define SSC_STA_NACK BIT(10)
88#define SSC_STA_REPSTRT BIT(11)
89#define SSC_STA_TX_FIFO_HALF BIT(12)
90#define SSC_STA_TX_FIFO_FULL BIT(13)
91#define SSC_STA_RX_FIFO_HALF BIT(14)
92
93/* SSC I2C Control */
94#define SSC_I2C_I2CM BIT(0)
95#define SSC_I2C_STRTG BIT(1)
96#define SSC_I2C_STOPG BIT(2)
97#define SSC_I2C_ACKG BIT(3)
98#define SSC_I2C_AD10 BIT(4)
99#define SSC_I2C_TXENB BIT(5)
100#define SSC_I2C_REPSTRTG BIT(11)
101#define SSC_I2C_SLAVE_DISABLE BIT(12)
102
103/* SSC Tx FIFO Status */
104#define SSC_TX_FSTAT_STATUS 0x07
105
106/* SSC Rx FIFO Status */
107#define SSC_RX_FSTAT_STATUS 0x07
108
109/* SSC Clear bit operation */
110#define SSC_CLR_SSCAAS BIT(6)
111#define SSC_CLR_SSCSTOP BIT(7)
112#define SSC_CLR_SSCARBL BIT(8)
113#define SSC_CLR_NACK BIT(10)
114#define SSC_CLR_REPSTRT BIT(11)
115
116/* SSC Clock Prescaler */
117#define SSC_PRSC_VALUE 0x0f
118
119
120#define SSC_TXFIFO_SIZE 0x8
121#define SSC_RXFIFO_SIZE 0x8
122
123enum st_i2c_mode {
124 I2C_MODE_STANDARD,
125 I2C_MODE_FAST,
126 I2C_MODE_END,
127};
128
129/**
130 * struct st_i2c_timings - per-Mode tuning parameters
131 * @rate: I2C bus rate
132 * @rep_start_hold: I2C repeated start hold time requirement
133 * @rep_start_setup: I2C repeated start set up time requirement
134 * @start_hold: I2C start hold time requirement
135 * @data_setup_time: I2C data set up time requirement
136 * @stop_setup_time: I2C stop set up time requirement
137 * @bus_free_time: I2C bus free time requirement
138 * @sda_pulse_min_limit: I2C SDA pulse mini width limit
139 */
140struct st_i2c_timings {
141 u32 rate;
142 u32 rep_start_hold;
143 u32 rep_start_setup;
144 u32 start_hold;
145 u32 data_setup_time;
146 u32 stop_setup_time;
147 u32 bus_free_time;
148 u32 sda_pulse_min_limit;
149};
150
151/**
152 * struct st_i2c_client - client specific data
153 * @addr: 8-bit slave addr, including r/w bit
154 * @count: number of bytes to be transfered
155 * @xfered: number of bytes already transferred
156 * @buf: data buffer
157 * @result: result of the transfer
158 * @stop: last I2C msg to be sent, i.e. STOP to be generated
159 */
160struct st_i2c_client {
161 u8 addr;
162 u32 count;
163 u32 xfered;
164 u8 *buf;
165 int result;
166 bool stop;
167};
168
169/**
170 * struct st_i2c_dev - private data of the controller
171 * @adap: I2C adapter for this controller
172 * @dev: device for this controller
173 * @base: virtual memory area
174 * @complete: completion of I2C message
175 * @irq: interrupt line for th controller
176 * @clk: hw ssc block clock
177 * @mode: I2C mode of the controller. Standard or Fast only supported
178 * @scl_min_width_us: SCL line minimum pulse width in us
179 * @sda_min_width_us: SDA line minimum pulse width in us
180 * @client: I2C transfert information
181 * @busy: I2C transfer on-going
182 */
183struct st_i2c_dev {
184 struct i2c_adapter adap;
185 struct device *dev;
186 void __iomem *base;
187 struct completion complete;
188 int irq;
189 struct clk *clk;
190 int mode;
191 u32 scl_min_width_us;
192 u32 sda_min_width_us;
193 struct st_i2c_client client;
194 bool busy;
195};
196
197static inline void st_i2c_set_bits(void __iomem *reg, u32 mask)
198{
199 writel_relaxed(readl_relaxed(reg) | mask, reg);
200}
201
202static inline void st_i2c_clr_bits(void __iomem *reg, u32 mask)
203{
204 writel_relaxed(readl_relaxed(reg) & ~mask, reg);
205}
206
207/*
208 * From I2C Specifications v0.5.
209 *
210 * All the values below have +10% margin added to be
211 * compatible with some out-of-spec devices,
212 * like HDMI link of the Toshiba 19AV600 TV.
213 */
214static struct st_i2c_timings i2c_timings[] = {
215 [I2C_MODE_STANDARD] = {
216 .rate = I2C_MAX_STANDARD_MODE_FREQ,
217 .rep_start_hold = 4400,
218 .rep_start_setup = 5170,
219 .start_hold = 4400,
220 .data_setup_time = 275,
221 .stop_setup_time = 4400,
222 .bus_free_time = 5170,
223 },
224 [I2C_MODE_FAST] = {
225 .rate = I2C_MAX_FAST_MODE_FREQ,
226 .rep_start_hold = 660,
227 .rep_start_setup = 660,
228 .start_hold = 660,
229 .data_setup_time = 110,
230 .stop_setup_time = 660,
231 .bus_free_time = 1430,
232 },
233};
234
235static void st_i2c_flush_rx_fifo(struct st_i2c_dev *i2c_dev)
236{
237 int count, i;
238
239 /*
240 * Counter only counts up to 7 but fifo size is 8...
241 * When fifo is full, counter is 0 and RIR bit of status register is
242 * set
243 */
244 if (readl_relaxed(i2c_dev->base + SSC_STA) & SSC_STA_RIR)
245 count = SSC_RXFIFO_SIZE;
246 else
247 count = readl_relaxed(i2c_dev->base + SSC_RX_FSTAT) &
248 SSC_RX_FSTAT_STATUS;
249
250 for (i = 0; i < count; i++)
251 readl_relaxed(i2c_dev->base + SSC_RBUF);
252}
253
254static void st_i2c_soft_reset(struct st_i2c_dev *i2c_dev)
255{
256 /*
257 * FIFO needs to be emptied before reseting the IP,
258 * else the controller raises a BUSY error.
259 */
260 st_i2c_flush_rx_fifo(i2c_dev);
261
262 st_i2c_set_bits(i2c_dev->base + SSC_CTL, SSC_CTL_SR);
263 st_i2c_clr_bits(i2c_dev->base + SSC_CTL, SSC_CTL_SR);
264}
265
266/**
267 * st_i2c_hw_config() - Prepare SSC block, calculate and apply tuning timings
268 * @i2c_dev: Controller's private data
269 */
270static void st_i2c_hw_config(struct st_i2c_dev *i2c_dev)
271{
272 unsigned long rate;
273 u32 val, ns_per_clk;
274 struct st_i2c_timings *t = &i2c_timings[i2c_dev->mode];
275
276 st_i2c_soft_reset(i2c_dev);
277
278 val = SSC_CLR_REPSTRT | SSC_CLR_NACK | SSC_CLR_SSCARBL |
279 SSC_CLR_SSCAAS | SSC_CLR_SSCSTOP;
280 writel_relaxed(val, i2c_dev->base + SSC_CLR);
281
282 /* SSC Control register setup */
283 val = SSC_CTL_PO | SSC_CTL_PH | SSC_CTL_HB | SSC_CTL_DATA_WIDTH_9;
284 writel_relaxed(val, i2c_dev->base + SSC_CTL);
285
286 rate = clk_get_rate(i2c_dev->clk);
287 ns_per_clk = 1000000000 / rate;
288
289 /* Baudrate */
290 val = rate / (2 * t->rate);
291 writel_relaxed(val, i2c_dev->base + SSC_BRG);
292
293 /* Pre-scaler baudrate */
294 writel_relaxed(1, i2c_dev->base + SSC_PRE_SCALER_BRG);
295
296 /* Enable I2C mode */
297 writel_relaxed(SSC_I2C_I2CM, i2c_dev->base + SSC_I2C);
298
299 /* Repeated start hold time */
300 val = t->rep_start_hold / ns_per_clk;
301 writel_relaxed(val, i2c_dev->base + SSC_REP_START_HOLD);
302
303 /* Repeated start set up time */
304 val = t->rep_start_setup / ns_per_clk;
305 writel_relaxed(val, i2c_dev->base + SSC_REP_START_SETUP);
306
307 /* Start hold time */
308 val = t->start_hold / ns_per_clk;
309 writel_relaxed(val, i2c_dev->base + SSC_START_HOLD);
310
311 /* Data set up time */
312 val = t->data_setup_time / ns_per_clk;
313 writel_relaxed(val, i2c_dev->base + SSC_DATA_SETUP);
314
315 /* Stop set up time */
316 val = t->stop_setup_time / ns_per_clk;
317 writel_relaxed(val, i2c_dev->base + SSC_STOP_SETUP);
318
319 /* Bus free time */
320 val = t->bus_free_time / ns_per_clk;
321 writel_relaxed(val, i2c_dev->base + SSC_BUS_FREE);
322
323 /* Prescalers set up */
324 val = rate / 10000000;
325 writel_relaxed(val, i2c_dev->base + SSC_PRSCALER);
326 writel_relaxed(val, i2c_dev->base + SSC_PRSCALER_DATAOUT);
327
328 /* Noise suppression witdh */
329 val = i2c_dev->scl_min_width_us * rate / 100000000;
330 writel_relaxed(val, i2c_dev->base + SSC_NOISE_SUPP_WIDTH);
331
332 /* Noise suppression max output data delay width */
333 val = i2c_dev->sda_min_width_us * rate / 100000000;
334 writel_relaxed(val, i2c_dev->base + SSC_NOISE_SUPP_WIDTH_DATAOUT);
335}
336
337static int st_i2c_recover_bus(struct i2c_adapter *i2c_adap)
338{
339 struct st_i2c_dev *i2c_dev = i2c_get_adapdata(i2c_adap);
340 u32 ctl;
341
342 dev_dbg(i2c_dev->dev, "Trying to recover bus\n");
343
344 /*
345 * SSP IP is dual role SPI/I2C to generate 9 clock pulses
346 * we switch to SPI node, 9 bit words and write a 0. This
347 * has been validate with a oscilloscope and is easier
348 * than switching to GPIO mode.
349 */
350
351 /* Disable interrupts */
352 writel_relaxed(0, i2c_dev->base + SSC_IEN);
353
354 st_i2c_hw_config(i2c_dev);
355
356 ctl = SSC_CTL_EN | SSC_CTL_MS | SSC_CTL_EN_RX_FIFO | SSC_CTL_EN_TX_FIFO;
357 st_i2c_set_bits(i2c_dev->base + SSC_CTL, ctl);
358
359 st_i2c_clr_bits(i2c_dev->base + SSC_I2C, SSC_I2C_I2CM);
360 usleep_range(8000, 10000);
361
362 writel_relaxed(0, i2c_dev->base + SSC_TBUF);
363 usleep_range(2000, 4000);
364 st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_I2CM);
365
366 return 0;
367}
368
369static int st_i2c_wait_free_bus(struct st_i2c_dev *i2c_dev)
370{
371 u32 sta;
372 int i, ret;
373
374 for (i = 0; i < 10; i++) {
375 sta = readl_relaxed(i2c_dev->base + SSC_STA);
376 if (!(sta & SSC_STA_BUSY))
377 return 0;
378
379 usleep_range(2000, 4000);
380 }
381
382 dev_err(i2c_dev->dev, "bus not free (status = 0x%08x)\n", sta);
383
384 ret = i2c_recover_bus(&i2c_dev->adap);
385 if (ret) {
386 dev_err(i2c_dev->dev, "Failed to recover the bus (%d)\n", ret);
387 return ret;
388 }
389
390 return -EBUSY;
391}
392
393/**
394 * st_i2c_write_tx_fifo() - Write a byte in the Tx FIFO
395 * @i2c_dev: Controller's private data
396 * @byte: Data to write in the Tx FIFO
397 */
398static inline void st_i2c_write_tx_fifo(struct st_i2c_dev *i2c_dev, u8 byte)
399{
400 u16 tbuf = byte << 1;
401
402 writel_relaxed(tbuf | 1, i2c_dev->base + SSC_TBUF);
403}
404
405/**
406 * st_i2c_wr_fill_tx_fifo() - Fill the Tx FIFO in write mode
407 * @i2c_dev: Controller's private data
408 *
409 * This functions fills the Tx FIFO with I2C transfert buffer when
410 * in write mode.
411 */
412static void st_i2c_wr_fill_tx_fifo(struct st_i2c_dev *i2c_dev)
413{
414 struct st_i2c_client *c = &i2c_dev->client;
415 u32 tx_fstat, sta;
416 int i;
417
418 sta = readl_relaxed(i2c_dev->base + SSC_STA);
419 if (sta & SSC_STA_TX_FIFO_FULL)
420 return;
421
422 tx_fstat = readl_relaxed(i2c_dev->base + SSC_TX_FSTAT);
423 tx_fstat &= SSC_TX_FSTAT_STATUS;
424
425 if (c->count < (SSC_TXFIFO_SIZE - tx_fstat))
426 i = c->count;
427 else
428 i = SSC_TXFIFO_SIZE - tx_fstat;
429
430 for (; i > 0; i--, c->count--, c->buf++)
431 st_i2c_write_tx_fifo(i2c_dev, *c->buf);
432}
433
434/**
435 * st_i2c_rd_fill_tx_fifo() - Fill the Tx FIFO in read mode
436 * @i2c_dev: Controller's private data
437 * @max: Maximum amount of data to fill into the Tx FIFO
438 *
439 * This functions fills the Tx FIFO with fixed pattern when
440 * in read mode to trigger clock.
441 */
442static void st_i2c_rd_fill_tx_fifo(struct st_i2c_dev *i2c_dev, int max)
443{
444 struct st_i2c_client *c = &i2c_dev->client;
445 u32 tx_fstat, sta;
446 int i;
447
448 sta = readl_relaxed(i2c_dev->base + SSC_STA);
449 if (sta & SSC_STA_TX_FIFO_FULL)
450 return;
451
452 tx_fstat = readl_relaxed(i2c_dev->base + SSC_TX_FSTAT);
453 tx_fstat &= SSC_TX_FSTAT_STATUS;
454
455 if (max < (SSC_TXFIFO_SIZE - tx_fstat))
456 i = max;
457 else
458 i = SSC_TXFIFO_SIZE - tx_fstat;
459
460 for (; i > 0; i--, c->xfered++)
461 st_i2c_write_tx_fifo(i2c_dev, 0xff);
462}
463
464static void st_i2c_read_rx_fifo(struct st_i2c_dev *i2c_dev)
465{
466 struct st_i2c_client *c = &i2c_dev->client;
467 u32 i, sta;
468 u16 rbuf;
469
470 sta = readl_relaxed(i2c_dev->base + SSC_STA);
471 if (sta & SSC_STA_RIR) {
472 i = SSC_RXFIFO_SIZE;
473 } else {
474 i = readl_relaxed(i2c_dev->base + SSC_RX_FSTAT);
475 i &= SSC_RX_FSTAT_STATUS;
476 }
477
478 for (; (i > 0) && (c->count > 0); i--, c->count--) {
479 rbuf = readl_relaxed(i2c_dev->base + SSC_RBUF) >> 1;
480 *c->buf++ = (u8)rbuf & 0xff;
481 }
482
483 if (i) {
484 dev_err(i2c_dev->dev, "Unexpected %d bytes in rx fifo\n", i);
485 st_i2c_flush_rx_fifo(i2c_dev);
486 }
487}
488
489/**
490 * st_i2c_terminate_xfer() - Send either STOP or REPSTART condition
491 * @i2c_dev: Controller's private data
492 */
493static void st_i2c_terminate_xfer(struct st_i2c_dev *i2c_dev)
494{
495 struct st_i2c_client *c = &i2c_dev->client;
496
497 st_i2c_clr_bits(i2c_dev->base + SSC_IEN, SSC_IEN_TEEN);
498 st_i2c_clr_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STRTG);
499
500 if (c->stop) {
501 st_i2c_set_bits(i2c_dev->base + SSC_IEN, SSC_IEN_STOPEN);
502 st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STOPG);
503 } else {
504 st_i2c_set_bits(i2c_dev->base + SSC_IEN, SSC_IEN_REPSTRTEN);
505 st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_REPSTRTG);
506 }
507}
508
509/**
510 * st_i2c_handle_write() - Handle FIFO empty interrupt in case of write
511 * @i2c_dev: Controller's private data
512 */
513static void st_i2c_handle_write(struct st_i2c_dev *i2c_dev)
514{
515 struct st_i2c_client *c = &i2c_dev->client;
516
517 st_i2c_flush_rx_fifo(i2c_dev);
518
519 if (!c->count)
520 /* End of xfer, send stop or repstart */
521 st_i2c_terminate_xfer(i2c_dev);
522 else
523 st_i2c_wr_fill_tx_fifo(i2c_dev);
524}
525
526/**
527 * st_i2c_handle_read() - Handle FIFO empty interrupt in case of read
528 * @i2c_dev: Controller's private data
529 */
530static void st_i2c_handle_read(struct st_i2c_dev *i2c_dev)
531{
532 struct st_i2c_client *c = &i2c_dev->client;
533 u32 ien;
534
535 /* Trash the address read back */
536 if (!c->xfered) {
537 readl_relaxed(i2c_dev->base + SSC_RBUF);
538 st_i2c_clr_bits(i2c_dev->base + SSC_I2C, SSC_I2C_TXENB);
539 } else {
540 st_i2c_read_rx_fifo(i2c_dev);
541 }
542
543 if (!c->count) {
544 /* End of xfer, send stop or repstart */
545 st_i2c_terminate_xfer(i2c_dev);
546 } else if (c->count == 1) {
547 /* Penultimate byte to xfer, disable ACK gen. */
548 st_i2c_clr_bits(i2c_dev->base + SSC_I2C, SSC_I2C_ACKG);
549
550 /* Last received byte is to be handled by NACK interrupt */
551 ien = SSC_IEN_NACKEN | SSC_IEN_ARBLEN;
552 writel_relaxed(ien, i2c_dev->base + SSC_IEN);
553
554 st_i2c_rd_fill_tx_fifo(i2c_dev, c->count);
555 } else {
556 st_i2c_rd_fill_tx_fifo(i2c_dev, c->count - 1);
557 }
558}
559
560/**
561 * st_i2c_isr_thread() - Interrupt routine
562 * @irq: interrupt number
563 * @data: Controller's private data
564 */
565static irqreturn_t st_i2c_isr_thread(int irq, void *data)
566{
567 struct st_i2c_dev *i2c_dev = data;
568 struct st_i2c_client *c = &i2c_dev->client;
569 u32 sta, ien;
570 int it;
571
572 ien = readl_relaxed(i2c_dev->base + SSC_IEN);
573 sta = readl_relaxed(i2c_dev->base + SSC_STA);
574
575 /* Use __fls() to check error bits first */
576 it = __fls(sta & ien);
577 if (it < 0) {
578 dev_dbg(i2c_dev->dev, "spurious it (sta=0x%04x, ien=0x%04x)\n",
579 sta, ien);
580 return IRQ_NONE;
581 }
582
583 switch (1 << it) {
584 case SSC_STA_TE:
585 if (c->addr & I2C_M_RD)
586 st_i2c_handle_read(i2c_dev);
587 else
588 st_i2c_handle_write(i2c_dev);
589 break;
590
591 case SSC_STA_STOP:
592 case SSC_STA_REPSTRT:
593 writel_relaxed(0, i2c_dev->base + SSC_IEN);
594 complete(&i2c_dev->complete);
595 break;
596
597 case SSC_STA_NACK:
598 writel_relaxed(SSC_CLR_NACK, i2c_dev->base + SSC_CLR);
599
600 /* Last received byte handled by NACK interrupt */
601 if ((c->addr & I2C_M_RD) && (c->count == 1) && (c->xfered)) {
602 st_i2c_handle_read(i2c_dev);
603 break;
604 }
605
606 it = SSC_IEN_STOPEN | SSC_IEN_ARBLEN;
607 writel_relaxed(it, i2c_dev->base + SSC_IEN);
608
609 st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STOPG);
610 c->result = -EIO;
611 break;
612
613 case SSC_STA_ARBL:
614 writel_relaxed(SSC_CLR_SSCARBL, i2c_dev->base + SSC_CLR);
615
616 it = SSC_IEN_STOPEN | SSC_IEN_ARBLEN;
617 writel_relaxed(it, i2c_dev->base + SSC_IEN);
618
619 st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STOPG);
620 c->result = -EAGAIN;
621 break;
622
623 default:
624 dev_err(i2c_dev->dev,
625 "it %d unhandled (sta=0x%04x)\n", it, sta);
626 }
627
628 /*
629 * Read IEN register to ensure interrupt mask write is effective
630 * before re-enabling interrupt at GIC level, and thus avoid spurious
631 * interrupts.
632 */
633 readl(i2c_dev->base + SSC_IEN);
634
635 return IRQ_HANDLED;
636}
637
638/**
639 * st_i2c_xfer_msg() - Transfer a single I2C message
640 * @i2c_dev: Controller's private data
641 * @msg: I2C message to transfer
642 * @is_first: first message of the sequence
643 * @is_last: last message of the sequence
644 */
645static int st_i2c_xfer_msg(struct st_i2c_dev *i2c_dev, struct i2c_msg *msg,
646 bool is_first, bool is_last)
647{
648 struct st_i2c_client *c = &i2c_dev->client;
649 u32 ctl, i2c, it;
650 unsigned long timeout;
651 int ret;
652
653 c->addr = i2c_8bit_addr_from_msg(msg);
654 c->buf = msg->buf;
655 c->count = msg->len;
656 c->xfered = 0;
657 c->result = 0;
658 c->stop = is_last;
659
660 reinit_completion(&i2c_dev->complete);
661
662 ctl = SSC_CTL_EN | SSC_CTL_MS | SSC_CTL_EN_RX_FIFO | SSC_CTL_EN_TX_FIFO;
663 st_i2c_set_bits(i2c_dev->base + SSC_CTL, ctl);
664
665 i2c = SSC_I2C_TXENB;
666 if (c->addr & I2C_M_RD)
667 i2c |= SSC_I2C_ACKG;
668 st_i2c_set_bits(i2c_dev->base + SSC_I2C, i2c);
669
670 /* Write slave address */
671 st_i2c_write_tx_fifo(i2c_dev, c->addr);
672
673 /* Pre-fill Tx fifo with data in case of write */
674 if (!(c->addr & I2C_M_RD))
675 st_i2c_wr_fill_tx_fifo(i2c_dev);
676
677 it = SSC_IEN_NACKEN | SSC_IEN_TEEN | SSC_IEN_ARBLEN;
678 writel_relaxed(it, i2c_dev->base + SSC_IEN);
679
680 if (is_first) {
681 ret = st_i2c_wait_free_bus(i2c_dev);
682 if (ret)
683 return ret;
684
685 st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STRTG);
686 }
687
688 timeout = wait_for_completion_timeout(&i2c_dev->complete,
689 i2c_dev->adap.timeout);
690 ret = c->result;
691
692 if (!timeout) {
693 dev_err(i2c_dev->dev, "Write to slave 0x%x timed out\n",
694 c->addr);
695 ret = -ETIMEDOUT;
696 }
697
698 i2c = SSC_I2C_STOPG | SSC_I2C_REPSTRTG;
699 st_i2c_clr_bits(i2c_dev->base + SSC_I2C, i2c);
700
701 writel_relaxed(SSC_CLR_SSCSTOP | SSC_CLR_REPSTRT,
702 i2c_dev->base + SSC_CLR);
703
704 return ret;
705}
706
707/**
708 * st_i2c_xfer() - Transfer a single I2C message
709 * @i2c_adap: Adapter pointer to the controller
710 * @msgs: Pointer to data to be written.
711 * @num: Number of messages to be executed
712 */
713static int st_i2c_xfer(struct i2c_adapter *i2c_adap,
714 struct i2c_msg msgs[], int num)
715{
716 struct st_i2c_dev *i2c_dev = i2c_get_adapdata(i2c_adap);
717 int ret, i;
718
719 i2c_dev->busy = true;
720
721 ret = clk_prepare_enable(i2c_dev->clk);
722 if (ret) {
723 dev_err(i2c_dev->dev, "Failed to prepare_enable clock\n");
724 return ret;
725 }
726
727 pinctrl_pm_select_default_state(i2c_dev->dev);
728
729 st_i2c_hw_config(i2c_dev);
730
731 for (i = 0; (i < num) && !ret; i++)
732 ret = st_i2c_xfer_msg(i2c_dev, &msgs[i], i == 0, i == num - 1);
733
734 pinctrl_pm_select_idle_state(i2c_dev->dev);
735
736 clk_disable_unprepare(i2c_dev->clk);
737
738 i2c_dev->busy = false;
739
740 return (ret < 0) ? ret : i;
741}
742
743static int st_i2c_suspend(struct device *dev)
744{
745 struct st_i2c_dev *i2c_dev = dev_get_drvdata(dev);
746
747 if (i2c_dev->busy)
748 return -EBUSY;
749
750 pinctrl_pm_select_sleep_state(dev);
751
752 return 0;
753}
754
755static int st_i2c_resume(struct device *dev)
756{
757 pinctrl_pm_select_default_state(dev);
758 /* Go in idle state if available */
759 pinctrl_pm_select_idle_state(dev);
760
761 return 0;
762}
763
764static DEFINE_SIMPLE_DEV_PM_OPS(st_i2c_pm, st_i2c_suspend, st_i2c_resume);
765
766static u32 st_i2c_func(struct i2c_adapter *adap)
767{
768 return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
769}
770
771static const struct i2c_algorithm st_i2c_algo = {
772 .master_xfer = st_i2c_xfer,
773 .functionality = st_i2c_func,
774};
775
776static struct i2c_bus_recovery_info st_i2c_recovery_info = {
777 .recover_bus = st_i2c_recover_bus,
778};
779
780static int st_i2c_of_get_deglitch(struct device_node *np,
781 struct st_i2c_dev *i2c_dev)
782{
783 int ret;
784
785 ret = of_property_read_u32(np, "st,i2c-min-scl-pulse-width-us",
786 &i2c_dev->scl_min_width_us);
787 if ((ret == -ENODATA) || (ret == -EOVERFLOW)) {
788 dev_err(i2c_dev->dev, "st,i2c-min-scl-pulse-width-us invalid\n");
789 return ret;
790 }
791
792 ret = of_property_read_u32(np, "st,i2c-min-sda-pulse-width-us",
793 &i2c_dev->sda_min_width_us);
794 if ((ret == -ENODATA) || (ret == -EOVERFLOW)) {
795 dev_err(i2c_dev->dev, "st,i2c-min-sda-pulse-width-us invalid\n");
796 return ret;
797 }
798
799 return 0;
800}
801
802static int st_i2c_probe(struct platform_device *pdev)
803{
804 struct device_node *np = pdev->dev.of_node;
805 struct st_i2c_dev *i2c_dev;
806 struct resource *res;
807 u32 clk_rate;
808 struct i2c_adapter *adap;
809 int ret;
810
811 i2c_dev = devm_kzalloc(&pdev->dev, sizeof(*i2c_dev), GFP_KERNEL);
812 if (!i2c_dev)
813 return -ENOMEM;
814
815 i2c_dev->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
816 if (IS_ERR(i2c_dev->base))
817 return PTR_ERR(i2c_dev->base);
818
819 i2c_dev->irq = irq_of_parse_and_map(np, 0);
820 if (!i2c_dev->irq) {
821 dev_err(&pdev->dev, "IRQ missing or invalid\n");
822 return -EINVAL;
823 }
824
825 i2c_dev->clk = of_clk_get_by_name(np, "ssc");
826 if (IS_ERR(i2c_dev->clk)) {
827 dev_err(&pdev->dev, "Unable to request clock\n");
828 return PTR_ERR(i2c_dev->clk);
829 }
830
831 i2c_dev->mode = I2C_MODE_STANDARD;
832 ret = of_property_read_u32(np, "clock-frequency", &clk_rate);
833 if (!ret && (clk_rate == I2C_MAX_FAST_MODE_FREQ))
834 i2c_dev->mode = I2C_MODE_FAST;
835
836 i2c_dev->dev = &pdev->dev;
837
838 ret = devm_request_threaded_irq(&pdev->dev, i2c_dev->irq,
839 NULL, st_i2c_isr_thread,
840 IRQF_ONESHOT, pdev->name, i2c_dev);
841 if (ret) {
842 dev_err(&pdev->dev, "Failed to request irq %i\n", i2c_dev->irq);
843 return ret;
844 }
845
846 pinctrl_pm_select_default_state(i2c_dev->dev);
847 /* In case idle state available, select it */
848 pinctrl_pm_select_idle_state(i2c_dev->dev);
849
850 ret = st_i2c_of_get_deglitch(np, i2c_dev);
851 if (ret)
852 return ret;
853
854 adap = &i2c_dev->adap;
855 i2c_set_adapdata(adap, i2c_dev);
856 snprintf(adap->name, sizeof(adap->name), "ST I2C(%pa)", &res->start);
857 adap->owner = THIS_MODULE;
858 adap->timeout = 2 * HZ;
859 adap->retries = 0;
860 adap->algo = &st_i2c_algo;
861 adap->bus_recovery_info = &st_i2c_recovery_info;
862 adap->dev.parent = &pdev->dev;
863 adap->dev.of_node = pdev->dev.of_node;
864
865 init_completion(&i2c_dev->complete);
866
867 ret = i2c_add_adapter(adap);
868 if (ret)
869 return ret;
870
871 platform_set_drvdata(pdev, i2c_dev);
872
873 dev_info(i2c_dev->dev, "%s initialized\n", adap->name);
874
875 return 0;
876}
877
878static void st_i2c_remove(struct platform_device *pdev)
879{
880 struct st_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
881
882 i2c_del_adapter(&i2c_dev->adap);
883}
884
885static const struct of_device_id st_i2c_match[] = {
886 { .compatible = "st,comms-ssc-i2c", },
887 { .compatible = "st,comms-ssc4-i2c", },
888 {},
889};
890MODULE_DEVICE_TABLE(of, st_i2c_match);
891
892static struct platform_driver st_i2c_driver = {
893 .driver = {
894 .name = "st-i2c",
895 .of_match_table = st_i2c_match,
896 .pm = pm_sleep_ptr(&st_i2c_pm),
897 },
898 .probe = st_i2c_probe,
899 .remove_new = st_i2c_remove,
900};
901
902module_platform_driver(st_i2c_driver);
903
904MODULE_AUTHOR("Maxime Coquelin <maxime.coquelin@st.com>");
905MODULE_DESCRIPTION("STMicroelectronics I2C driver");
906MODULE_LICENSE("GPL v2");
1/*
2 * Copyright (C) 2013 STMicroelectronics
3 *
4 * I2C master mode controller driver, used in STMicroelectronics devices.
5 *
6 * Author: Maxime Coquelin <maxime.coquelin@st.com>
7 *
8 * This program is free software; you can redistribute it and/or modify
9 * it under the terms of the GNU General Public License version 2, as
10 * published by the Free Software Foundation.
11 */
12
13#include <linux/clk.h>
14#include <linux/delay.h>
15#include <linux/err.h>
16#include <linux/i2c.h>
17#include <linux/interrupt.h>
18#include <linux/io.h>
19#include <linux/module.h>
20#include <linux/of_address.h>
21#include <linux/of_irq.h>
22#include <linux/of.h>
23#include <linux/pinctrl/consumer.h>
24#include <linux/platform_device.h>
25
26/* SSC registers */
27#define SSC_BRG 0x000
28#define SSC_TBUF 0x004
29#define SSC_RBUF 0x008
30#define SSC_CTL 0x00C
31#define SSC_IEN 0x010
32#define SSC_STA 0x014
33#define SSC_I2C 0x018
34#define SSC_SLAD 0x01C
35#define SSC_REP_START_HOLD 0x020
36#define SSC_START_HOLD 0x024
37#define SSC_REP_START_SETUP 0x028
38#define SSC_DATA_SETUP 0x02C
39#define SSC_STOP_SETUP 0x030
40#define SSC_BUS_FREE 0x034
41#define SSC_TX_FSTAT 0x038
42#define SSC_RX_FSTAT 0x03C
43#define SSC_PRE_SCALER_BRG 0x040
44#define SSC_CLR 0x080
45#define SSC_NOISE_SUPP_WIDTH 0x100
46#define SSC_PRSCALER 0x104
47#define SSC_NOISE_SUPP_WIDTH_DATAOUT 0x108
48#define SSC_PRSCALER_DATAOUT 0x10c
49
50/* SSC Control */
51#define SSC_CTL_DATA_WIDTH_9 0x8
52#define SSC_CTL_DATA_WIDTH_MSK 0xf
53#define SSC_CTL_BM 0xf
54#define SSC_CTL_HB BIT(4)
55#define SSC_CTL_PH BIT(5)
56#define SSC_CTL_PO BIT(6)
57#define SSC_CTL_SR BIT(7)
58#define SSC_CTL_MS BIT(8)
59#define SSC_CTL_EN BIT(9)
60#define SSC_CTL_LPB BIT(10)
61#define SSC_CTL_EN_TX_FIFO BIT(11)
62#define SSC_CTL_EN_RX_FIFO BIT(12)
63#define SSC_CTL_EN_CLST_RX BIT(13)
64
65/* SSC Interrupt Enable */
66#define SSC_IEN_RIEN BIT(0)
67#define SSC_IEN_TIEN BIT(1)
68#define SSC_IEN_TEEN BIT(2)
69#define SSC_IEN_REEN BIT(3)
70#define SSC_IEN_PEEN BIT(4)
71#define SSC_IEN_AASEN BIT(6)
72#define SSC_IEN_STOPEN BIT(7)
73#define SSC_IEN_ARBLEN BIT(8)
74#define SSC_IEN_NACKEN BIT(10)
75#define SSC_IEN_REPSTRTEN BIT(11)
76#define SSC_IEN_TX_FIFO_HALF BIT(12)
77#define SSC_IEN_RX_FIFO_HALF_FULL BIT(14)
78
79/* SSC Status */
80#define SSC_STA_RIR BIT(0)
81#define SSC_STA_TIR BIT(1)
82#define SSC_STA_TE BIT(2)
83#define SSC_STA_RE BIT(3)
84#define SSC_STA_PE BIT(4)
85#define SSC_STA_CLST BIT(5)
86#define SSC_STA_AAS BIT(6)
87#define SSC_STA_STOP BIT(7)
88#define SSC_STA_ARBL BIT(8)
89#define SSC_STA_BUSY BIT(9)
90#define SSC_STA_NACK BIT(10)
91#define SSC_STA_REPSTRT BIT(11)
92#define SSC_STA_TX_FIFO_HALF BIT(12)
93#define SSC_STA_TX_FIFO_FULL BIT(13)
94#define SSC_STA_RX_FIFO_HALF BIT(14)
95
96/* SSC I2C Control */
97#define SSC_I2C_I2CM BIT(0)
98#define SSC_I2C_STRTG BIT(1)
99#define SSC_I2C_STOPG BIT(2)
100#define SSC_I2C_ACKG BIT(3)
101#define SSC_I2C_AD10 BIT(4)
102#define SSC_I2C_TXENB BIT(5)
103#define SSC_I2C_REPSTRTG BIT(11)
104#define SSC_I2C_SLAVE_DISABLE BIT(12)
105
106/* SSC Tx FIFO Status */
107#define SSC_TX_FSTAT_STATUS 0x07
108
109/* SSC Rx FIFO Status */
110#define SSC_RX_FSTAT_STATUS 0x07
111
112/* SSC Clear bit operation */
113#define SSC_CLR_SSCAAS BIT(6)
114#define SSC_CLR_SSCSTOP BIT(7)
115#define SSC_CLR_SSCARBL BIT(8)
116#define SSC_CLR_NACK BIT(10)
117#define SSC_CLR_REPSTRT BIT(11)
118
119/* SSC Clock Prescaler */
120#define SSC_PRSC_VALUE 0x0f
121
122
123#define SSC_TXFIFO_SIZE 0x8
124#define SSC_RXFIFO_SIZE 0x8
125
126enum st_i2c_mode {
127 I2C_MODE_STANDARD,
128 I2C_MODE_FAST,
129 I2C_MODE_END,
130};
131
132/**
133 * struct st_i2c_timings - per-Mode tuning parameters
134 * @rate: I2C bus rate
135 * @rep_start_hold: I2C repeated start hold time requirement
136 * @rep_start_setup: I2C repeated start set up time requirement
137 * @start_hold: I2C start hold time requirement
138 * @data_setup_time: I2C data set up time requirement
139 * @stop_setup_time: I2C stop set up time requirement
140 * @bus_free_time: I2C bus free time requirement
141 * @sda_pulse_min_limit: I2C SDA pulse mini width limit
142 */
143struct st_i2c_timings {
144 u32 rate;
145 u32 rep_start_hold;
146 u32 rep_start_setup;
147 u32 start_hold;
148 u32 data_setup_time;
149 u32 stop_setup_time;
150 u32 bus_free_time;
151 u32 sda_pulse_min_limit;
152};
153
154/**
155 * struct st_i2c_client - client specific data
156 * @addr: 8-bit slave addr, including r/w bit
157 * @count: number of bytes to be transfered
158 * @xfered: number of bytes already transferred
159 * @buf: data buffer
160 * @result: result of the transfer
161 * @stop: last I2C msg to be sent, i.e. STOP to be generated
162 */
163struct st_i2c_client {
164 u8 addr;
165 u32 count;
166 u32 xfered;
167 u8 *buf;
168 int result;
169 bool stop;
170};
171
172/**
173 * struct st_i2c_dev - private data of the controller
174 * @adap: I2C adapter for this controller
175 * @dev: device for this controller
176 * @base: virtual memory area
177 * @complete: completion of I2C message
178 * @irq: interrupt line for th controller
179 * @clk: hw ssc block clock
180 * @mode: I2C mode of the controller. Standard or Fast only supported
181 * @scl_min_width_us: SCL line minimum pulse width in us
182 * @sda_min_width_us: SDA line minimum pulse width in us
183 * @client: I2C transfert information
184 * @busy: I2C transfer on-going
185 */
186struct st_i2c_dev {
187 struct i2c_adapter adap;
188 struct device *dev;
189 void __iomem *base;
190 struct completion complete;
191 int irq;
192 struct clk *clk;
193 int mode;
194 u32 scl_min_width_us;
195 u32 sda_min_width_us;
196 struct st_i2c_client client;
197 bool busy;
198};
199
200static inline void st_i2c_set_bits(void __iomem *reg, u32 mask)
201{
202 writel_relaxed(readl_relaxed(reg) | mask, reg);
203}
204
205static inline void st_i2c_clr_bits(void __iomem *reg, u32 mask)
206{
207 writel_relaxed(readl_relaxed(reg) & ~mask, reg);
208}
209
210/*
211 * From I2C Specifications v0.5.
212 *
213 * All the values below have +10% margin added to be
214 * compatible with some out-of-spec devices,
215 * like HDMI link of the Toshiba 19AV600 TV.
216 */
217static struct st_i2c_timings i2c_timings[] = {
218 [I2C_MODE_STANDARD] = {
219 .rate = 100000,
220 .rep_start_hold = 4400,
221 .rep_start_setup = 5170,
222 .start_hold = 4400,
223 .data_setup_time = 275,
224 .stop_setup_time = 4400,
225 .bus_free_time = 5170,
226 },
227 [I2C_MODE_FAST] = {
228 .rate = 400000,
229 .rep_start_hold = 660,
230 .rep_start_setup = 660,
231 .start_hold = 660,
232 .data_setup_time = 110,
233 .stop_setup_time = 660,
234 .bus_free_time = 1430,
235 },
236};
237
238static void st_i2c_flush_rx_fifo(struct st_i2c_dev *i2c_dev)
239{
240 int count, i;
241
242 /*
243 * Counter only counts up to 7 but fifo size is 8...
244 * When fifo is full, counter is 0 and RIR bit of status register is
245 * set
246 */
247 if (readl_relaxed(i2c_dev->base + SSC_STA) & SSC_STA_RIR)
248 count = SSC_RXFIFO_SIZE;
249 else
250 count = readl_relaxed(i2c_dev->base + SSC_RX_FSTAT) &
251 SSC_RX_FSTAT_STATUS;
252
253 for (i = 0; i < count; i++)
254 readl_relaxed(i2c_dev->base + SSC_RBUF);
255}
256
257static void st_i2c_soft_reset(struct st_i2c_dev *i2c_dev)
258{
259 /*
260 * FIFO needs to be emptied before reseting the IP,
261 * else the controller raises a BUSY error.
262 */
263 st_i2c_flush_rx_fifo(i2c_dev);
264
265 st_i2c_set_bits(i2c_dev->base + SSC_CTL, SSC_CTL_SR);
266 st_i2c_clr_bits(i2c_dev->base + SSC_CTL, SSC_CTL_SR);
267}
268
269/**
270 * st_i2c_hw_config() - Prepare SSC block, calculate and apply tuning timings
271 * @i2c_dev: Controller's private data
272 */
273static void st_i2c_hw_config(struct st_i2c_dev *i2c_dev)
274{
275 unsigned long rate;
276 u32 val, ns_per_clk;
277 struct st_i2c_timings *t = &i2c_timings[i2c_dev->mode];
278
279 st_i2c_soft_reset(i2c_dev);
280
281 val = SSC_CLR_REPSTRT | SSC_CLR_NACK | SSC_CLR_SSCARBL |
282 SSC_CLR_SSCAAS | SSC_CLR_SSCSTOP;
283 writel_relaxed(val, i2c_dev->base + SSC_CLR);
284
285 /* SSC Control register setup */
286 val = SSC_CTL_PO | SSC_CTL_PH | SSC_CTL_HB | SSC_CTL_DATA_WIDTH_9;
287 writel_relaxed(val, i2c_dev->base + SSC_CTL);
288
289 rate = clk_get_rate(i2c_dev->clk);
290 ns_per_clk = 1000000000 / rate;
291
292 /* Baudrate */
293 val = rate / (2 * t->rate);
294 writel_relaxed(val, i2c_dev->base + SSC_BRG);
295
296 /* Pre-scaler baudrate */
297 writel_relaxed(1, i2c_dev->base + SSC_PRE_SCALER_BRG);
298
299 /* Enable I2C mode */
300 writel_relaxed(SSC_I2C_I2CM, i2c_dev->base + SSC_I2C);
301
302 /* Repeated start hold time */
303 val = t->rep_start_hold / ns_per_clk;
304 writel_relaxed(val, i2c_dev->base + SSC_REP_START_HOLD);
305
306 /* Repeated start set up time */
307 val = t->rep_start_setup / ns_per_clk;
308 writel_relaxed(val, i2c_dev->base + SSC_REP_START_SETUP);
309
310 /* Start hold time */
311 val = t->start_hold / ns_per_clk;
312 writel_relaxed(val, i2c_dev->base + SSC_START_HOLD);
313
314 /* Data set up time */
315 val = t->data_setup_time / ns_per_clk;
316 writel_relaxed(val, i2c_dev->base + SSC_DATA_SETUP);
317
318 /* Stop set up time */
319 val = t->stop_setup_time / ns_per_clk;
320 writel_relaxed(val, i2c_dev->base + SSC_STOP_SETUP);
321
322 /* Bus free time */
323 val = t->bus_free_time / ns_per_clk;
324 writel_relaxed(val, i2c_dev->base + SSC_BUS_FREE);
325
326 /* Prescalers set up */
327 val = rate / 10000000;
328 writel_relaxed(val, i2c_dev->base + SSC_PRSCALER);
329 writel_relaxed(val, i2c_dev->base + SSC_PRSCALER_DATAOUT);
330
331 /* Noise suppression witdh */
332 val = i2c_dev->scl_min_width_us * rate / 100000000;
333 writel_relaxed(val, i2c_dev->base + SSC_NOISE_SUPP_WIDTH);
334
335 /* Noise suppression max output data delay width */
336 val = i2c_dev->sda_min_width_us * rate / 100000000;
337 writel_relaxed(val, i2c_dev->base + SSC_NOISE_SUPP_WIDTH_DATAOUT);
338}
339
340static int st_i2c_recover_bus(struct i2c_adapter *i2c_adap)
341{
342 struct st_i2c_dev *i2c_dev = i2c_get_adapdata(i2c_adap);
343 u32 ctl;
344
345 dev_dbg(i2c_dev->dev, "Trying to recover bus\n");
346
347 /*
348 * SSP IP is dual role SPI/I2C to generate 9 clock pulses
349 * we switch to SPI node, 9 bit words and write a 0. This
350 * has been validate with a oscilloscope and is easier
351 * than switching to GPIO mode.
352 */
353
354 /* Disable interrupts */
355 writel_relaxed(0, i2c_dev->base + SSC_IEN);
356
357 st_i2c_hw_config(i2c_dev);
358
359 ctl = SSC_CTL_EN | SSC_CTL_MS | SSC_CTL_EN_RX_FIFO | SSC_CTL_EN_TX_FIFO;
360 st_i2c_set_bits(i2c_dev->base + SSC_CTL, ctl);
361
362 st_i2c_clr_bits(i2c_dev->base + SSC_I2C, SSC_I2C_I2CM);
363 usleep_range(8000, 10000);
364
365 writel_relaxed(0, i2c_dev->base + SSC_TBUF);
366 usleep_range(2000, 4000);
367 st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_I2CM);
368
369 return 0;
370}
371
372static int st_i2c_wait_free_bus(struct st_i2c_dev *i2c_dev)
373{
374 u32 sta;
375 int i, ret;
376
377 for (i = 0; i < 10; i++) {
378 sta = readl_relaxed(i2c_dev->base + SSC_STA);
379 if (!(sta & SSC_STA_BUSY))
380 return 0;
381
382 usleep_range(2000, 4000);
383 }
384
385 dev_err(i2c_dev->dev, "bus not free (status = 0x%08x)\n", sta);
386
387 ret = i2c_recover_bus(&i2c_dev->adap);
388 if (ret) {
389 dev_err(i2c_dev->dev, "Failed to recover the bus (%d)\n", ret);
390 return ret;
391 }
392
393 return -EBUSY;
394}
395
396/**
397 * st_i2c_write_tx_fifo() - Write a byte in the Tx FIFO
398 * @i2c_dev: Controller's private data
399 * @byte: Data to write in the Tx FIFO
400 */
401static inline void st_i2c_write_tx_fifo(struct st_i2c_dev *i2c_dev, u8 byte)
402{
403 u16 tbuf = byte << 1;
404
405 writel_relaxed(tbuf | 1, i2c_dev->base + SSC_TBUF);
406}
407
408/**
409 * st_i2c_wr_fill_tx_fifo() - Fill the Tx FIFO in write mode
410 * @i2c_dev: Controller's private data
411 *
412 * This functions fills the Tx FIFO with I2C transfert buffer when
413 * in write mode.
414 */
415static void st_i2c_wr_fill_tx_fifo(struct st_i2c_dev *i2c_dev)
416{
417 struct st_i2c_client *c = &i2c_dev->client;
418 u32 tx_fstat, sta;
419 int i;
420
421 sta = readl_relaxed(i2c_dev->base + SSC_STA);
422 if (sta & SSC_STA_TX_FIFO_FULL)
423 return;
424
425 tx_fstat = readl_relaxed(i2c_dev->base + SSC_TX_FSTAT);
426 tx_fstat &= SSC_TX_FSTAT_STATUS;
427
428 if (c->count < (SSC_TXFIFO_SIZE - tx_fstat))
429 i = c->count;
430 else
431 i = SSC_TXFIFO_SIZE - tx_fstat;
432
433 for (; i > 0; i--, c->count--, c->buf++)
434 st_i2c_write_tx_fifo(i2c_dev, *c->buf);
435}
436
437/**
438 * st_i2c_rd_fill_tx_fifo() - Fill the Tx FIFO in read mode
439 * @i2c_dev: Controller's private data
440 *
441 * This functions fills the Tx FIFO with fixed pattern when
442 * in read mode to trigger clock.
443 */
444static void st_i2c_rd_fill_tx_fifo(struct st_i2c_dev *i2c_dev, int max)
445{
446 struct st_i2c_client *c = &i2c_dev->client;
447 u32 tx_fstat, sta;
448 int i;
449
450 sta = readl_relaxed(i2c_dev->base + SSC_STA);
451 if (sta & SSC_STA_TX_FIFO_FULL)
452 return;
453
454 tx_fstat = readl_relaxed(i2c_dev->base + SSC_TX_FSTAT);
455 tx_fstat &= SSC_TX_FSTAT_STATUS;
456
457 if (max < (SSC_TXFIFO_SIZE - tx_fstat))
458 i = max;
459 else
460 i = SSC_TXFIFO_SIZE - tx_fstat;
461
462 for (; i > 0; i--, c->xfered++)
463 st_i2c_write_tx_fifo(i2c_dev, 0xff);
464}
465
466static void st_i2c_read_rx_fifo(struct st_i2c_dev *i2c_dev)
467{
468 struct st_i2c_client *c = &i2c_dev->client;
469 u32 i, sta;
470 u16 rbuf;
471
472 sta = readl_relaxed(i2c_dev->base + SSC_STA);
473 if (sta & SSC_STA_RIR) {
474 i = SSC_RXFIFO_SIZE;
475 } else {
476 i = readl_relaxed(i2c_dev->base + SSC_RX_FSTAT);
477 i &= SSC_RX_FSTAT_STATUS;
478 }
479
480 for (; (i > 0) && (c->count > 0); i--, c->count--) {
481 rbuf = readl_relaxed(i2c_dev->base + SSC_RBUF) >> 1;
482 *c->buf++ = (u8)rbuf & 0xff;
483 }
484
485 if (i) {
486 dev_err(i2c_dev->dev, "Unexpected %d bytes in rx fifo\n", i);
487 st_i2c_flush_rx_fifo(i2c_dev);
488 }
489}
490
491/**
492 * st_i2c_terminate_xfer() - Send either STOP or REPSTART condition
493 * @i2c_dev: Controller's private data
494 */
495static void st_i2c_terminate_xfer(struct st_i2c_dev *i2c_dev)
496{
497 struct st_i2c_client *c = &i2c_dev->client;
498
499 st_i2c_clr_bits(i2c_dev->base + SSC_IEN, SSC_IEN_TEEN);
500 st_i2c_clr_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STRTG);
501
502 if (c->stop) {
503 st_i2c_set_bits(i2c_dev->base + SSC_IEN, SSC_IEN_STOPEN);
504 st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STOPG);
505 } else {
506 st_i2c_set_bits(i2c_dev->base + SSC_IEN, SSC_IEN_REPSTRTEN);
507 st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_REPSTRTG);
508 }
509}
510
511/**
512 * st_i2c_handle_write() - Handle FIFO empty interrupt in case of write
513 * @i2c_dev: Controller's private data
514 */
515static void st_i2c_handle_write(struct st_i2c_dev *i2c_dev)
516{
517 struct st_i2c_client *c = &i2c_dev->client;
518
519 st_i2c_flush_rx_fifo(i2c_dev);
520
521 if (!c->count)
522 /* End of xfer, send stop or repstart */
523 st_i2c_terminate_xfer(i2c_dev);
524 else
525 st_i2c_wr_fill_tx_fifo(i2c_dev);
526}
527
528/**
529 * st_i2c_handle_write() - Handle FIFO enmpty interrupt in case of read
530 * @i2c_dev: Controller's private data
531 */
532static void st_i2c_handle_read(struct st_i2c_dev *i2c_dev)
533{
534 struct st_i2c_client *c = &i2c_dev->client;
535 u32 ien;
536
537 /* Trash the address read back */
538 if (!c->xfered) {
539 readl_relaxed(i2c_dev->base + SSC_RBUF);
540 st_i2c_clr_bits(i2c_dev->base + SSC_I2C, SSC_I2C_TXENB);
541 } else {
542 st_i2c_read_rx_fifo(i2c_dev);
543 }
544
545 if (!c->count) {
546 /* End of xfer, send stop or repstart */
547 st_i2c_terminate_xfer(i2c_dev);
548 } else if (c->count == 1) {
549 /* Penultimate byte to xfer, disable ACK gen. */
550 st_i2c_clr_bits(i2c_dev->base + SSC_I2C, SSC_I2C_ACKG);
551
552 /* Last received byte is to be handled by NACK interrupt */
553 ien = SSC_IEN_NACKEN | SSC_IEN_ARBLEN;
554 writel_relaxed(ien, i2c_dev->base + SSC_IEN);
555
556 st_i2c_rd_fill_tx_fifo(i2c_dev, c->count);
557 } else {
558 st_i2c_rd_fill_tx_fifo(i2c_dev, c->count - 1);
559 }
560}
561
562/**
563 * st_i2c_isr() - Interrupt routine
564 * @irq: interrupt number
565 * @data: Controller's private data
566 */
567static irqreturn_t st_i2c_isr_thread(int irq, void *data)
568{
569 struct st_i2c_dev *i2c_dev = data;
570 struct st_i2c_client *c = &i2c_dev->client;
571 u32 sta, ien;
572 int it;
573
574 ien = readl_relaxed(i2c_dev->base + SSC_IEN);
575 sta = readl_relaxed(i2c_dev->base + SSC_STA);
576
577 /* Use __fls() to check error bits first */
578 it = __fls(sta & ien);
579 if (it < 0) {
580 dev_dbg(i2c_dev->dev, "spurious it (sta=0x%04x, ien=0x%04x)\n",
581 sta, ien);
582 return IRQ_NONE;
583 }
584
585 switch (1 << it) {
586 case SSC_STA_TE:
587 if (c->addr & I2C_M_RD)
588 st_i2c_handle_read(i2c_dev);
589 else
590 st_i2c_handle_write(i2c_dev);
591 break;
592
593 case SSC_STA_STOP:
594 case SSC_STA_REPSTRT:
595 writel_relaxed(0, i2c_dev->base + SSC_IEN);
596 complete(&i2c_dev->complete);
597 break;
598
599 case SSC_STA_NACK:
600 writel_relaxed(SSC_CLR_NACK, i2c_dev->base + SSC_CLR);
601
602 /* Last received byte handled by NACK interrupt */
603 if ((c->addr & I2C_M_RD) && (c->count == 1) && (c->xfered)) {
604 st_i2c_handle_read(i2c_dev);
605 break;
606 }
607
608 it = SSC_IEN_STOPEN | SSC_IEN_ARBLEN;
609 writel_relaxed(it, i2c_dev->base + SSC_IEN);
610
611 st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STOPG);
612 c->result = -EIO;
613 break;
614
615 case SSC_STA_ARBL:
616 writel_relaxed(SSC_CLR_SSCARBL, i2c_dev->base + SSC_CLR);
617
618 it = SSC_IEN_STOPEN | SSC_IEN_ARBLEN;
619 writel_relaxed(it, i2c_dev->base + SSC_IEN);
620
621 st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STOPG);
622 c->result = -EAGAIN;
623 break;
624
625 default:
626 dev_err(i2c_dev->dev,
627 "it %d unhandled (sta=0x%04x)\n", it, sta);
628 }
629
630 /*
631 * Read IEN register to ensure interrupt mask write is effective
632 * before re-enabling interrupt at GIC level, and thus avoid spurious
633 * interrupts.
634 */
635 readl(i2c_dev->base + SSC_IEN);
636
637 return IRQ_HANDLED;
638}
639
640/**
641 * st_i2c_xfer_msg() - Transfer a single I2C message
642 * @i2c_dev: Controller's private data
643 * @msg: I2C message to transfer
644 * @is_first: first message of the sequence
645 * @is_last: last message of the sequence
646 */
647static int st_i2c_xfer_msg(struct st_i2c_dev *i2c_dev, struct i2c_msg *msg,
648 bool is_first, bool is_last)
649{
650 struct st_i2c_client *c = &i2c_dev->client;
651 u32 ctl, i2c, it;
652 unsigned long timeout;
653 int ret;
654
655 c->addr = i2c_8bit_addr_from_msg(msg);
656 c->buf = msg->buf;
657 c->count = msg->len;
658 c->xfered = 0;
659 c->result = 0;
660 c->stop = is_last;
661
662 reinit_completion(&i2c_dev->complete);
663
664 ctl = SSC_CTL_EN | SSC_CTL_MS | SSC_CTL_EN_RX_FIFO | SSC_CTL_EN_TX_FIFO;
665 st_i2c_set_bits(i2c_dev->base + SSC_CTL, ctl);
666
667 i2c = SSC_I2C_TXENB;
668 if (c->addr & I2C_M_RD)
669 i2c |= SSC_I2C_ACKG;
670 st_i2c_set_bits(i2c_dev->base + SSC_I2C, i2c);
671
672 /* Write slave address */
673 st_i2c_write_tx_fifo(i2c_dev, c->addr);
674
675 /* Pre-fill Tx fifo with data in case of write */
676 if (!(c->addr & I2C_M_RD))
677 st_i2c_wr_fill_tx_fifo(i2c_dev);
678
679 it = SSC_IEN_NACKEN | SSC_IEN_TEEN | SSC_IEN_ARBLEN;
680 writel_relaxed(it, i2c_dev->base + SSC_IEN);
681
682 if (is_first) {
683 ret = st_i2c_wait_free_bus(i2c_dev);
684 if (ret)
685 return ret;
686
687 st_i2c_set_bits(i2c_dev->base + SSC_I2C, SSC_I2C_STRTG);
688 }
689
690 timeout = wait_for_completion_timeout(&i2c_dev->complete,
691 i2c_dev->adap.timeout);
692 ret = c->result;
693
694 if (!timeout) {
695 dev_err(i2c_dev->dev, "Write to slave 0x%x timed out\n",
696 c->addr);
697 ret = -ETIMEDOUT;
698 }
699
700 i2c = SSC_I2C_STOPG | SSC_I2C_REPSTRTG;
701 st_i2c_clr_bits(i2c_dev->base + SSC_I2C, i2c);
702
703 writel_relaxed(SSC_CLR_SSCSTOP | SSC_CLR_REPSTRT,
704 i2c_dev->base + SSC_CLR);
705
706 return ret;
707}
708
709/**
710 * st_i2c_xfer() - Transfer a single I2C message
711 * @i2c_adap: Adapter pointer to the controller
712 * @msgs: Pointer to data to be written.
713 * @num: Number of messages to be executed
714 */
715static int st_i2c_xfer(struct i2c_adapter *i2c_adap,
716 struct i2c_msg msgs[], int num)
717{
718 struct st_i2c_dev *i2c_dev = i2c_get_adapdata(i2c_adap);
719 int ret, i;
720
721 i2c_dev->busy = true;
722
723 ret = clk_prepare_enable(i2c_dev->clk);
724 if (ret) {
725 dev_err(i2c_dev->dev, "Failed to prepare_enable clock\n");
726 return ret;
727 }
728
729 pinctrl_pm_select_default_state(i2c_dev->dev);
730
731 st_i2c_hw_config(i2c_dev);
732
733 for (i = 0; (i < num) && !ret; i++)
734 ret = st_i2c_xfer_msg(i2c_dev, &msgs[i], i == 0, i == num - 1);
735
736 pinctrl_pm_select_idle_state(i2c_dev->dev);
737
738 clk_disable_unprepare(i2c_dev->clk);
739
740 i2c_dev->busy = false;
741
742 return (ret < 0) ? ret : i;
743}
744
745#ifdef CONFIG_PM_SLEEP
746static int st_i2c_suspend(struct device *dev)
747{
748 struct platform_device *pdev = to_platform_device(dev);
749 struct st_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
750
751 if (i2c_dev->busy)
752 return -EBUSY;
753
754 pinctrl_pm_select_sleep_state(dev);
755
756 return 0;
757}
758
759static int st_i2c_resume(struct device *dev)
760{
761 pinctrl_pm_select_default_state(dev);
762 /* Go in idle state if available */
763 pinctrl_pm_select_idle_state(dev);
764
765 return 0;
766}
767
768static SIMPLE_DEV_PM_OPS(st_i2c_pm, st_i2c_suspend, st_i2c_resume);
769#define ST_I2C_PM (&st_i2c_pm)
770#else
771#define ST_I2C_PM NULL
772#endif
773
774static u32 st_i2c_func(struct i2c_adapter *adap)
775{
776 return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
777}
778
779static struct i2c_algorithm st_i2c_algo = {
780 .master_xfer = st_i2c_xfer,
781 .functionality = st_i2c_func,
782};
783
784static struct i2c_bus_recovery_info st_i2c_recovery_info = {
785 .recover_bus = st_i2c_recover_bus,
786};
787
788static int st_i2c_of_get_deglitch(struct device_node *np,
789 struct st_i2c_dev *i2c_dev)
790{
791 int ret;
792
793 ret = of_property_read_u32(np, "st,i2c-min-scl-pulse-width-us",
794 &i2c_dev->scl_min_width_us);
795 if ((ret == -ENODATA) || (ret == -EOVERFLOW)) {
796 dev_err(i2c_dev->dev, "st,i2c-min-scl-pulse-width-us invalid\n");
797 return ret;
798 }
799
800 ret = of_property_read_u32(np, "st,i2c-min-sda-pulse-width-us",
801 &i2c_dev->sda_min_width_us);
802 if ((ret == -ENODATA) || (ret == -EOVERFLOW)) {
803 dev_err(i2c_dev->dev, "st,i2c-min-sda-pulse-width-us invalid\n");
804 return ret;
805 }
806
807 return 0;
808}
809
810static int st_i2c_probe(struct platform_device *pdev)
811{
812 struct device_node *np = pdev->dev.of_node;
813 struct st_i2c_dev *i2c_dev;
814 struct resource *res;
815 u32 clk_rate;
816 struct i2c_adapter *adap;
817 int ret;
818
819 i2c_dev = devm_kzalloc(&pdev->dev, sizeof(*i2c_dev), GFP_KERNEL);
820 if (!i2c_dev)
821 return -ENOMEM;
822
823 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
824 i2c_dev->base = devm_ioremap_resource(&pdev->dev, res);
825 if (IS_ERR(i2c_dev->base))
826 return PTR_ERR(i2c_dev->base);
827
828 i2c_dev->irq = irq_of_parse_and_map(np, 0);
829 if (!i2c_dev->irq) {
830 dev_err(&pdev->dev, "IRQ missing or invalid\n");
831 return -EINVAL;
832 }
833
834 i2c_dev->clk = of_clk_get_by_name(np, "ssc");
835 if (IS_ERR(i2c_dev->clk)) {
836 dev_err(&pdev->dev, "Unable to request clock\n");
837 return PTR_ERR(i2c_dev->clk);
838 }
839
840 i2c_dev->mode = I2C_MODE_STANDARD;
841 ret = of_property_read_u32(np, "clock-frequency", &clk_rate);
842 if ((!ret) && (clk_rate == 400000))
843 i2c_dev->mode = I2C_MODE_FAST;
844
845 i2c_dev->dev = &pdev->dev;
846
847 ret = devm_request_threaded_irq(&pdev->dev, i2c_dev->irq,
848 NULL, st_i2c_isr_thread,
849 IRQF_ONESHOT, pdev->name, i2c_dev);
850 if (ret) {
851 dev_err(&pdev->dev, "Failed to request irq %i\n", i2c_dev->irq);
852 return ret;
853 }
854
855 pinctrl_pm_select_default_state(i2c_dev->dev);
856 /* In case idle state available, select it */
857 pinctrl_pm_select_idle_state(i2c_dev->dev);
858
859 ret = st_i2c_of_get_deglitch(np, i2c_dev);
860 if (ret)
861 return ret;
862
863 adap = &i2c_dev->adap;
864 i2c_set_adapdata(adap, i2c_dev);
865 snprintf(adap->name, sizeof(adap->name), "ST I2C(%pa)", &res->start);
866 adap->owner = THIS_MODULE;
867 adap->timeout = 2 * HZ;
868 adap->retries = 0;
869 adap->algo = &st_i2c_algo;
870 adap->bus_recovery_info = &st_i2c_recovery_info;
871 adap->dev.parent = &pdev->dev;
872 adap->dev.of_node = pdev->dev.of_node;
873
874 init_completion(&i2c_dev->complete);
875
876 ret = i2c_add_adapter(adap);
877 if (ret)
878 return ret;
879
880 platform_set_drvdata(pdev, i2c_dev);
881
882 dev_info(i2c_dev->dev, "%s initialized\n", adap->name);
883
884 return 0;
885}
886
887static int st_i2c_remove(struct platform_device *pdev)
888{
889 struct st_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
890
891 i2c_del_adapter(&i2c_dev->adap);
892
893 return 0;
894}
895
896static const struct of_device_id st_i2c_match[] = {
897 { .compatible = "st,comms-ssc-i2c", },
898 { .compatible = "st,comms-ssc4-i2c", },
899 {},
900};
901MODULE_DEVICE_TABLE(of, st_i2c_match);
902
903static struct platform_driver st_i2c_driver = {
904 .driver = {
905 .name = "st-i2c",
906 .of_match_table = st_i2c_match,
907 .pm = ST_I2C_PM,
908 },
909 .probe = st_i2c_probe,
910 .remove = st_i2c_remove,
911};
912
913module_platform_driver(st_i2c_driver);
914
915MODULE_AUTHOR("Maxime Coquelin <maxime.coquelin@st.com>");
916MODULE_DESCRIPTION("STMicroelectronics I2C driver");
917MODULE_LICENSE("GPL v2");