Loading...
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * Edgeport USB Serial Converter driver
4 *
5 * Copyright (C) 2000 Inside Out Networks, All rights reserved.
6 * Copyright (C) 2001-2002 Greg Kroah-Hartman <greg@kroah.com>
7 *
8 * Supports the following devices:
9 * Edgeport/4
10 * Edgeport/4t
11 * Edgeport/2
12 * Edgeport/4i
13 * Edgeport/2i
14 * Edgeport/421
15 * Edgeport/21
16 * Rapidport/4
17 * Edgeport/8
18 * Edgeport/2D8
19 * Edgeport/4D8
20 * Edgeport/8i
21 *
22 * For questions or problems with this driver, contact Inside Out
23 * Networks technical support, or Peter Berger <pberger@brimson.com>,
24 * or Al Borchers <alborchers@steinerpoint.com>.
25 *
26 */
27
28#include <linux/kernel.h>
29#include <linux/jiffies.h>
30#include <linux/errno.h>
31#include <linux/slab.h>
32#include <linux/tty.h>
33#include <linux/tty_driver.h>
34#include <linux/tty_flip.h>
35#include <linux/module.h>
36#include <linux/spinlock.h>
37#include <linux/serial.h>
38#include <linux/ioctl.h>
39#include <linux/wait.h>
40#include <linux/firmware.h>
41#include <linux/ihex.h>
42#include <linux/uaccess.h>
43#include <linux/usb.h>
44#include <linux/usb/serial.h>
45#include "io_edgeport.h"
46#include "io_ionsp.h" /* info for the iosp messages */
47#include "io_16654.h" /* 16654 UART defines */
48
49#define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com> and David Iacovelli"
50#define DRIVER_DESC "Edgeport USB Serial Driver"
51
52#define MAX_NAME_LEN 64
53
54#define OPEN_TIMEOUT (5*HZ) /* 5 seconds */
55
56static const struct usb_device_id edgeport_2port_id_table[] = {
57 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_2) },
58 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_2I) },
59 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_421) },
60 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_21) },
61 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_2_DIN) },
62 { }
63};
64
65static const struct usb_device_id edgeport_4port_id_table[] = {
66 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_4) },
67 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_RAPIDPORT_4) },
68 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_4T) },
69 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_MT4X56USB) },
70 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_4I) },
71 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_8_DUAL_CPU) },
72 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_4_DIN) },
73 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_22I) },
74 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_412_4) },
75 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_COMPATIBLE) },
76 { }
77};
78
79static const struct usb_device_id edgeport_8port_id_table[] = {
80 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_8) },
81 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_16_DUAL_CPU) },
82 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_8I) },
83 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_8R) },
84 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_8RR) },
85 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_412_8) },
86 { }
87};
88
89static const struct usb_device_id Epic_port_id_table[] = {
90 { USB_DEVICE(USB_VENDOR_ID_NCR, NCR_DEVICE_ID_EPIC_0202) },
91 { USB_DEVICE(USB_VENDOR_ID_NCR, NCR_DEVICE_ID_EPIC_0203) },
92 { USB_DEVICE(USB_VENDOR_ID_NCR, NCR_DEVICE_ID_EPIC_0310) },
93 { USB_DEVICE(USB_VENDOR_ID_NCR, NCR_DEVICE_ID_EPIC_0311) },
94 { USB_DEVICE(USB_VENDOR_ID_NCR, NCR_DEVICE_ID_EPIC_0312) },
95 { USB_DEVICE(USB_VENDOR_ID_AXIOHM, AXIOHM_DEVICE_ID_EPIC_A758) },
96 { USB_DEVICE(USB_VENDOR_ID_AXIOHM, AXIOHM_DEVICE_ID_EPIC_A794) },
97 { USB_DEVICE(USB_VENDOR_ID_AXIOHM, AXIOHM_DEVICE_ID_EPIC_A225) },
98 { }
99};
100
101/* Devices that this driver supports */
102static const struct usb_device_id id_table_combined[] = {
103 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_4) },
104 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_RAPIDPORT_4) },
105 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_4T) },
106 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_MT4X56USB) },
107 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_2) },
108 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_4I) },
109 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_2I) },
110 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_421) },
111 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_21) },
112 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_8_DUAL_CPU) },
113 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_8) },
114 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_2_DIN) },
115 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_4_DIN) },
116 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_16_DUAL_CPU) },
117 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_22I) },
118 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_412_4) },
119 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_COMPATIBLE) },
120 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_8I) },
121 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_8R) },
122 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_8RR) },
123 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_EDGEPORT_412_8) },
124 { USB_DEVICE(USB_VENDOR_ID_NCR, NCR_DEVICE_ID_EPIC_0202) },
125 { USB_DEVICE(USB_VENDOR_ID_NCR, NCR_DEVICE_ID_EPIC_0203) },
126 { USB_DEVICE(USB_VENDOR_ID_NCR, NCR_DEVICE_ID_EPIC_0310) },
127 { USB_DEVICE(USB_VENDOR_ID_NCR, NCR_DEVICE_ID_EPIC_0311) },
128 { USB_DEVICE(USB_VENDOR_ID_NCR, NCR_DEVICE_ID_EPIC_0312) },
129 { USB_DEVICE(USB_VENDOR_ID_AXIOHM, AXIOHM_DEVICE_ID_EPIC_A758) },
130 { USB_DEVICE(USB_VENDOR_ID_AXIOHM, AXIOHM_DEVICE_ID_EPIC_A794) },
131 { USB_DEVICE(USB_VENDOR_ID_AXIOHM, AXIOHM_DEVICE_ID_EPIC_A225) },
132 { } /* Terminating entry */
133};
134
135MODULE_DEVICE_TABLE(usb, id_table_combined);
136
137
138/* receive port state */
139enum RXSTATE {
140 EXPECT_HDR1 = 0, /* Expect header byte 1 */
141 EXPECT_HDR2 = 1, /* Expect header byte 2 */
142 EXPECT_DATA = 2, /* Expect 'RxBytesRemaining' data */
143 EXPECT_HDR3 = 3, /* Expect header byte 3 (for status hdrs only) */
144};
145
146
147/* Transmit Fifo
148 * This Transmit queue is an extension of the edgeport Rx buffer.
149 * The maximum amount of data buffered in both the edgeport
150 * Rx buffer (maxTxCredits) and this buffer will never exceed maxTxCredits.
151 */
152struct TxFifo {
153 unsigned int head; /* index to head pointer (write) */
154 unsigned int tail; /* index to tail pointer (read) */
155 unsigned int count; /* Bytes in queue */
156 unsigned int size; /* Max size of queue (equal to Max number of TxCredits) */
157 unsigned char *fifo; /* allocated Buffer */
158};
159
160/* This structure holds all of the local port information */
161struct edgeport_port {
162 __u16 txCredits; /* our current credits for this port */
163 __u16 maxTxCredits; /* the max size of the port */
164
165 struct TxFifo txfifo; /* transmit fifo -- size will be maxTxCredits */
166 struct urb *write_urb; /* write URB for this port */
167 bool write_in_progress; /* 'true' while a write URB is outstanding */
168 spinlock_t ep_lock;
169
170 __u8 shadowLCR; /* last LCR value received */
171 __u8 shadowMCR; /* last MCR value received */
172 __u8 shadowMSR; /* last MSR value received */
173 __u8 shadowLSR; /* last LSR value received */
174 __u8 shadowXonChar; /* last value set as XON char in Edgeport */
175 __u8 shadowXoffChar; /* last value set as XOFF char in Edgeport */
176 __u8 validDataMask;
177 __u32 baudRate;
178
179 bool open;
180 bool openPending;
181 bool commandPending;
182 bool closePending;
183 bool chaseResponsePending;
184
185 wait_queue_head_t wait_chase; /* for handling sleeping while waiting for chase to finish */
186 wait_queue_head_t wait_open; /* for handling sleeping while waiting for open to finish */
187 wait_queue_head_t wait_command; /* for handling sleeping while waiting for command to finish */
188
189 struct usb_serial_port *port; /* loop back to the owner of this object */
190};
191
192
193/* This structure holds all of the individual device information */
194struct edgeport_serial {
195 char name[MAX_NAME_LEN+2]; /* string name of this device */
196
197 struct edge_manuf_descriptor manuf_descriptor; /* the manufacturer descriptor */
198 struct edge_boot_descriptor boot_descriptor; /* the boot firmware descriptor */
199 struct edgeport_product_info product_info; /* Product Info */
200 struct edge_compatibility_descriptor epic_descriptor; /* Edgeport compatible descriptor */
201 int is_epic; /* flag if EPiC device or not */
202
203 __u8 interrupt_in_endpoint; /* the interrupt endpoint handle */
204 unsigned char *interrupt_in_buffer; /* the buffer we use for the interrupt endpoint */
205 struct urb *interrupt_read_urb; /* our interrupt urb */
206
207 __u8 bulk_in_endpoint; /* the bulk in endpoint handle */
208 unsigned char *bulk_in_buffer; /* the buffer we use for the bulk in endpoint */
209 struct urb *read_urb; /* our bulk read urb */
210 bool read_in_progress;
211 spinlock_t es_lock;
212
213 __u8 bulk_out_endpoint; /* the bulk out endpoint handle */
214
215 __s16 rxBytesAvail; /* the number of bytes that we need to read from this device */
216
217 enum RXSTATE rxState; /* the current state of the bulk receive processor */
218 __u8 rxHeader1; /* receive header byte 1 */
219 __u8 rxHeader2; /* receive header byte 2 */
220 __u8 rxHeader3; /* receive header byte 3 */
221 __u8 rxPort; /* the port that we are currently receiving data for */
222 __u8 rxStatusCode; /* the receive status code */
223 __u8 rxStatusParam; /* the receive status parameter */
224 __s16 rxBytesRemaining; /* the number of port bytes left to read */
225 struct usb_serial *serial; /* loop back to the owner of this object */
226};
227
228/* baud rate information */
229struct divisor_table_entry {
230 __u32 BaudRate;
231 __u16 Divisor;
232};
233
234/*
235 * Define table of divisors for Rev A EdgePort/4 hardware
236 * These assume a 3.6864MHz crystal, the standard /16, and
237 * MCR.7 = 0.
238 */
239
240static const struct divisor_table_entry divisor_table[] = {
241 { 50, 4608},
242 { 75, 3072},
243 { 110, 2095}, /* 2094.545455 => 230450 => .0217 % over */
244 { 134, 1713}, /* 1713.011152 => 230398.5 => .00065% under */
245 { 150, 1536},
246 { 300, 768},
247 { 600, 384},
248 { 1200, 192},
249 { 1800, 128},
250 { 2400, 96},
251 { 4800, 48},
252 { 7200, 32},
253 { 9600, 24},
254 { 14400, 16},
255 { 19200, 12},
256 { 38400, 6},
257 { 57600, 4},
258 { 115200, 2},
259 { 230400, 1},
260};
261
262/* Number of outstanding Command Write Urbs */
263static atomic_t CmdUrbs = ATOMIC_INIT(0);
264
265
266/* function prototypes */
267
268static void edge_close(struct usb_serial_port *port);
269
270static void process_rcvd_data(struct edgeport_serial *edge_serial,
271 unsigned char *buffer, __u16 bufferLength);
272static void process_rcvd_status(struct edgeport_serial *edge_serial,
273 __u8 byte2, __u8 byte3);
274static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data,
275 int length);
276static void handle_new_msr(struct edgeport_port *edge_port, __u8 newMsr);
277static void handle_new_lsr(struct edgeport_port *edge_port, __u8 lsrData,
278 __u8 lsr, __u8 data);
279static int send_iosp_ext_cmd(struct edgeport_port *edge_port, __u8 command,
280 __u8 param);
281static int calc_baud_rate_divisor(struct device *dev, int baud_rate, int *divisor);
282static void change_port_settings(struct tty_struct *tty,
283 struct edgeport_port *edge_port,
284 const struct ktermios *old_termios);
285static int send_cmd_write_uart_register(struct edgeport_port *edge_port,
286 __u8 regNum, __u8 regValue);
287static int write_cmd_usb(struct edgeport_port *edge_port,
288 unsigned char *buffer, int writeLength);
289static void send_more_port_data(struct edgeport_serial *edge_serial,
290 struct edgeport_port *edge_port);
291
292static int rom_write(struct usb_serial *serial, __u16 extAddr, __u16 addr,
293 __u16 length, const __u8 *data);
294
295/* ************************************************************************ */
296/* ************************************************************************ */
297/* ************************************************************************ */
298/* ************************************************************************ */
299
300/************************************************************************
301 * *
302 * update_edgeport_E2PROM() Compare current versions of *
303 * Boot ROM and Manufacture *
304 * Descriptors with versions *
305 * embedded in this driver *
306 * *
307 ************************************************************************/
308static void update_edgeport_E2PROM(struct edgeport_serial *edge_serial)
309{
310 struct device *dev = &edge_serial->serial->dev->dev;
311 __u32 BootCurVer;
312 __u32 BootNewVer;
313 __u8 BootMajorVersion;
314 __u8 BootMinorVersion;
315 __u16 BootBuildNumber;
316 __u32 Bootaddr;
317 const struct ihex_binrec *rec;
318 const struct firmware *fw;
319 const char *fw_name;
320 int response;
321
322 switch (edge_serial->product_info.iDownloadFile) {
323 case EDGE_DOWNLOAD_FILE_I930:
324 fw_name = "edgeport/boot.fw";
325 break;
326 case EDGE_DOWNLOAD_FILE_80251:
327 fw_name = "edgeport/boot2.fw";
328 break;
329 default:
330 return;
331 }
332
333 response = request_ihex_firmware(&fw, fw_name,
334 &edge_serial->serial->dev->dev);
335 if (response) {
336 dev_err(dev, "Failed to load image \"%s\" err %d\n",
337 fw_name, response);
338 return;
339 }
340
341 rec = (const struct ihex_binrec *)fw->data;
342 BootMajorVersion = rec->data[0];
343 BootMinorVersion = rec->data[1];
344 BootBuildNumber = (rec->data[2] << 8) | rec->data[3];
345
346 /* Check Boot Image Version */
347 BootCurVer = (edge_serial->boot_descriptor.MajorVersion << 24) +
348 (edge_serial->boot_descriptor.MinorVersion << 16) +
349 le16_to_cpu(edge_serial->boot_descriptor.BuildNumber);
350
351 BootNewVer = (BootMajorVersion << 24) +
352 (BootMinorVersion << 16) +
353 BootBuildNumber;
354
355 dev_dbg(dev, "Current Boot Image version %d.%d.%d\n",
356 edge_serial->boot_descriptor.MajorVersion,
357 edge_serial->boot_descriptor.MinorVersion,
358 le16_to_cpu(edge_serial->boot_descriptor.BuildNumber));
359
360
361 if (BootNewVer > BootCurVer) {
362 dev_dbg(dev, "**Update Boot Image from %d.%d.%d to %d.%d.%d\n",
363 edge_serial->boot_descriptor.MajorVersion,
364 edge_serial->boot_descriptor.MinorVersion,
365 le16_to_cpu(edge_serial->boot_descriptor.BuildNumber),
366 BootMajorVersion, BootMinorVersion, BootBuildNumber);
367
368 dev_dbg(dev, "Downloading new Boot Image\n");
369
370 for (rec = ihex_next_binrec(rec); rec;
371 rec = ihex_next_binrec(rec)) {
372 Bootaddr = be32_to_cpu(rec->addr);
373 response = rom_write(edge_serial->serial,
374 Bootaddr >> 16,
375 Bootaddr & 0xFFFF,
376 be16_to_cpu(rec->len),
377 &rec->data[0]);
378 if (response < 0) {
379 dev_err(&edge_serial->serial->dev->dev,
380 "rom_write failed (%x, %x, %d)\n",
381 Bootaddr >> 16, Bootaddr & 0xFFFF,
382 be16_to_cpu(rec->len));
383 break;
384 }
385 }
386 } else {
387 dev_dbg(dev, "Boot Image -- already up to date\n");
388 }
389 release_firmware(fw);
390}
391
392static void dump_product_info(struct edgeport_serial *edge_serial,
393 struct edgeport_product_info *product_info)
394{
395 struct device *dev = &edge_serial->serial->dev->dev;
396
397 /* Dump Product Info structure */
398 dev_dbg(dev, "**Product Information:\n");
399 dev_dbg(dev, " ProductId %x\n", product_info->ProductId);
400 dev_dbg(dev, " NumPorts %d\n", product_info->NumPorts);
401 dev_dbg(dev, " ProdInfoVer %d\n", product_info->ProdInfoVer);
402 dev_dbg(dev, " IsServer %d\n", product_info->IsServer);
403 dev_dbg(dev, " IsRS232 %d\n", product_info->IsRS232);
404 dev_dbg(dev, " IsRS422 %d\n", product_info->IsRS422);
405 dev_dbg(dev, " IsRS485 %d\n", product_info->IsRS485);
406 dev_dbg(dev, " RomSize %d\n", product_info->RomSize);
407 dev_dbg(dev, " RamSize %d\n", product_info->RamSize);
408 dev_dbg(dev, " CpuRev %x\n", product_info->CpuRev);
409 dev_dbg(dev, " BoardRev %x\n", product_info->BoardRev);
410 dev_dbg(dev, " BootMajorVersion %d.%d.%d\n",
411 product_info->BootMajorVersion,
412 product_info->BootMinorVersion,
413 le16_to_cpu(product_info->BootBuildNumber));
414 dev_dbg(dev, " FirmwareMajorVersion %d.%d.%d\n",
415 product_info->FirmwareMajorVersion,
416 product_info->FirmwareMinorVersion,
417 le16_to_cpu(product_info->FirmwareBuildNumber));
418 dev_dbg(dev, " ManufactureDescDate %d/%d/%d\n",
419 product_info->ManufactureDescDate[0],
420 product_info->ManufactureDescDate[1],
421 product_info->ManufactureDescDate[2]+1900);
422 dev_dbg(dev, " iDownloadFile 0x%x\n",
423 product_info->iDownloadFile);
424 dev_dbg(dev, " EpicVer %d\n", product_info->EpicVer);
425}
426
427static void get_product_info(struct edgeport_serial *edge_serial)
428{
429 struct edgeport_product_info *product_info = &edge_serial->product_info;
430
431 memset(product_info, 0, sizeof(struct edgeport_product_info));
432
433 product_info->ProductId = (__u16)(le16_to_cpu(edge_serial->serial->dev->descriptor.idProduct) & ~ION_DEVICE_ID_80251_NETCHIP);
434 product_info->NumPorts = edge_serial->manuf_descriptor.NumPorts;
435 product_info->ProdInfoVer = 0;
436
437 product_info->RomSize = edge_serial->manuf_descriptor.RomSize;
438 product_info->RamSize = edge_serial->manuf_descriptor.RamSize;
439 product_info->CpuRev = edge_serial->manuf_descriptor.CpuRev;
440 product_info->BoardRev = edge_serial->manuf_descriptor.BoardRev;
441
442 product_info->BootMajorVersion =
443 edge_serial->boot_descriptor.MajorVersion;
444 product_info->BootMinorVersion =
445 edge_serial->boot_descriptor.MinorVersion;
446 product_info->BootBuildNumber =
447 edge_serial->boot_descriptor.BuildNumber;
448
449 memcpy(product_info->ManufactureDescDate,
450 edge_serial->manuf_descriptor.DescDate,
451 sizeof(edge_serial->manuf_descriptor.DescDate));
452
453 /* check if this is 2nd generation hardware */
454 if (le16_to_cpu(edge_serial->serial->dev->descriptor.idProduct)
455 & ION_DEVICE_ID_80251_NETCHIP)
456 product_info->iDownloadFile = EDGE_DOWNLOAD_FILE_80251;
457 else
458 product_info->iDownloadFile = EDGE_DOWNLOAD_FILE_I930;
459
460 /* Determine Product type and set appropriate flags */
461 switch (DEVICE_ID_FROM_USB_PRODUCT_ID(product_info->ProductId)) {
462 case ION_DEVICE_ID_EDGEPORT_COMPATIBLE:
463 case ION_DEVICE_ID_EDGEPORT_4T:
464 case ION_DEVICE_ID_EDGEPORT_4:
465 case ION_DEVICE_ID_EDGEPORT_2:
466 case ION_DEVICE_ID_EDGEPORT_8_DUAL_CPU:
467 case ION_DEVICE_ID_EDGEPORT_8:
468 case ION_DEVICE_ID_EDGEPORT_421:
469 case ION_DEVICE_ID_EDGEPORT_21:
470 case ION_DEVICE_ID_EDGEPORT_2_DIN:
471 case ION_DEVICE_ID_EDGEPORT_4_DIN:
472 case ION_DEVICE_ID_EDGEPORT_16_DUAL_CPU:
473 product_info->IsRS232 = 1;
474 break;
475
476 case ION_DEVICE_ID_EDGEPORT_2I: /* Edgeport/2 RS422/RS485 */
477 product_info->IsRS422 = 1;
478 product_info->IsRS485 = 1;
479 break;
480
481 case ION_DEVICE_ID_EDGEPORT_8I: /* Edgeport/4 RS422 */
482 case ION_DEVICE_ID_EDGEPORT_4I: /* Edgeport/4 RS422 */
483 product_info->IsRS422 = 1;
484 break;
485 }
486
487 dump_product_info(edge_serial, product_info);
488}
489
490static int get_epic_descriptor(struct edgeport_serial *ep)
491{
492 int result;
493 struct usb_serial *serial = ep->serial;
494 struct edgeport_product_info *product_info = &ep->product_info;
495 struct edge_compatibility_descriptor *epic;
496 struct edge_compatibility_bits *bits;
497 struct device *dev = &serial->dev->dev;
498
499 ep->is_epic = 0;
500
501 epic = kmalloc(sizeof(*epic), GFP_KERNEL);
502 if (!epic)
503 return -ENOMEM;
504
505 result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
506 USB_REQUEST_ION_GET_EPIC_DESC,
507 0xC0, 0x00, 0x00,
508 epic, sizeof(*epic),
509 300);
510 if (result == sizeof(*epic)) {
511 ep->is_epic = 1;
512 memcpy(&ep->epic_descriptor, epic, sizeof(*epic));
513 memset(product_info, 0, sizeof(struct edgeport_product_info));
514
515 product_info->NumPorts = epic->NumPorts;
516 product_info->ProdInfoVer = 0;
517 product_info->FirmwareMajorVersion = epic->MajorVersion;
518 product_info->FirmwareMinorVersion = epic->MinorVersion;
519 product_info->FirmwareBuildNumber = epic->BuildNumber;
520 product_info->iDownloadFile = epic->iDownloadFile;
521 product_info->EpicVer = epic->EpicVer;
522 product_info->Epic = epic->Supports;
523 product_info->ProductId = ION_DEVICE_ID_EDGEPORT_COMPATIBLE;
524 dump_product_info(ep, product_info);
525
526 bits = &ep->epic_descriptor.Supports;
527 dev_dbg(dev, "**EPIC descriptor:\n");
528 dev_dbg(dev, " VendEnableSuspend: %s\n", bits->VendEnableSuspend ? "TRUE": "FALSE");
529 dev_dbg(dev, " IOSPOpen : %s\n", bits->IOSPOpen ? "TRUE": "FALSE");
530 dev_dbg(dev, " IOSPClose : %s\n", bits->IOSPClose ? "TRUE": "FALSE");
531 dev_dbg(dev, " IOSPChase : %s\n", bits->IOSPChase ? "TRUE": "FALSE");
532 dev_dbg(dev, " IOSPSetRxFlow : %s\n", bits->IOSPSetRxFlow ? "TRUE": "FALSE");
533 dev_dbg(dev, " IOSPSetTxFlow : %s\n", bits->IOSPSetTxFlow ? "TRUE": "FALSE");
534 dev_dbg(dev, " IOSPSetXChar : %s\n", bits->IOSPSetXChar ? "TRUE": "FALSE");
535 dev_dbg(dev, " IOSPRxCheck : %s\n", bits->IOSPRxCheck ? "TRUE": "FALSE");
536 dev_dbg(dev, " IOSPSetClrBreak : %s\n", bits->IOSPSetClrBreak ? "TRUE": "FALSE");
537 dev_dbg(dev, " IOSPWriteMCR : %s\n", bits->IOSPWriteMCR ? "TRUE": "FALSE");
538 dev_dbg(dev, " IOSPWriteLCR : %s\n", bits->IOSPWriteLCR ? "TRUE": "FALSE");
539 dev_dbg(dev, " IOSPSetBaudRate : %s\n", bits->IOSPSetBaudRate ? "TRUE": "FALSE");
540 dev_dbg(dev, " TrueEdgeport : %s\n", bits->TrueEdgeport ? "TRUE": "FALSE");
541
542 result = 0;
543 } else if (result >= 0) {
544 dev_warn(&serial->interface->dev, "short epic descriptor received: %d\n",
545 result);
546 result = -EIO;
547 }
548
549 kfree(epic);
550
551 return result;
552}
553
554
555/************************************************************************/
556/************************************************************************/
557/* U S B C A L L B A C K F U N C T I O N S */
558/* U S B C A L L B A C K F U N C T I O N S */
559/************************************************************************/
560/************************************************************************/
561
562/*****************************************************************************
563 * edge_interrupt_callback
564 * this is the callback function for when we have received data on the
565 * interrupt endpoint.
566 *****************************************************************************/
567static void edge_interrupt_callback(struct urb *urb)
568{
569 struct edgeport_serial *edge_serial = urb->context;
570 struct device *dev;
571 struct edgeport_port *edge_port;
572 struct usb_serial_port *port;
573 unsigned char *data = urb->transfer_buffer;
574 int length = urb->actual_length;
575 unsigned long flags;
576 int bytes_avail;
577 int position;
578 int txCredits;
579 int portNumber;
580 int result;
581 int status = urb->status;
582
583 switch (status) {
584 case 0:
585 /* success */
586 break;
587 case -ECONNRESET:
588 case -ENOENT:
589 case -ESHUTDOWN:
590 /* this urb is terminated, clean up */
591 dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", __func__, status);
592 return;
593 default:
594 dev_dbg(&urb->dev->dev, "%s - nonzero urb status received: %d\n", __func__, status);
595 goto exit;
596 }
597
598 dev = &edge_serial->serial->dev->dev;
599
600 /* process this interrupt-read even if there are no ports open */
601 if (length) {
602 usb_serial_debug_data(dev, __func__, length, data);
603
604 if (length > 1) {
605 bytes_avail = data[0] | (data[1] << 8);
606 if (bytes_avail) {
607 spin_lock_irqsave(&edge_serial->es_lock, flags);
608 edge_serial->rxBytesAvail += bytes_avail;
609 dev_dbg(dev,
610 "%s - bytes_avail=%d, rxBytesAvail=%d, read_in_progress=%d\n",
611 __func__, bytes_avail,
612 edge_serial->rxBytesAvail,
613 edge_serial->read_in_progress);
614
615 if (edge_serial->rxBytesAvail > 0 &&
616 !edge_serial->read_in_progress) {
617 dev_dbg(dev, "%s - posting a read\n", __func__);
618 edge_serial->read_in_progress = true;
619
620 /* we have pending bytes on the
621 bulk in pipe, send a request */
622 result = usb_submit_urb(edge_serial->read_urb, GFP_ATOMIC);
623 if (result) {
624 dev_err(dev,
625 "%s - usb_submit_urb(read bulk) failed with result = %d\n",
626 __func__, result);
627 edge_serial->read_in_progress = false;
628 }
629 }
630 spin_unlock_irqrestore(&edge_serial->es_lock,
631 flags);
632 }
633 }
634 /* grab the txcredits for the ports if available */
635 position = 2;
636 portNumber = 0;
637 while ((position < length - 1) &&
638 (portNumber < edge_serial->serial->num_ports)) {
639 txCredits = data[position] | (data[position+1] << 8);
640 if (txCredits) {
641 port = edge_serial->serial->port[portNumber];
642 edge_port = usb_get_serial_port_data(port);
643 if (edge_port && edge_port->open) {
644 spin_lock_irqsave(&edge_port->ep_lock,
645 flags);
646 edge_port->txCredits += txCredits;
647 spin_unlock_irqrestore(&edge_port->ep_lock,
648 flags);
649 dev_dbg(dev, "%s - txcredits for port%d = %d\n",
650 __func__, portNumber,
651 edge_port->txCredits);
652
653 /* tell the tty driver that something
654 has changed */
655 tty_port_tty_wakeup(&edge_port->port->port);
656 /* Since we have more credit, check
657 if more data can be sent */
658 send_more_port_data(edge_serial,
659 edge_port);
660 }
661 }
662 position += 2;
663 ++portNumber;
664 }
665 }
666
667exit:
668 result = usb_submit_urb(urb, GFP_ATOMIC);
669 if (result)
670 dev_err(&urb->dev->dev,
671 "%s - Error %d submitting control urb\n",
672 __func__, result);
673}
674
675
676/*****************************************************************************
677 * edge_bulk_in_callback
678 * this is the callback function for when we have received data on the
679 * bulk in endpoint.
680 *****************************************************************************/
681static void edge_bulk_in_callback(struct urb *urb)
682{
683 struct edgeport_serial *edge_serial = urb->context;
684 struct device *dev;
685 unsigned char *data = urb->transfer_buffer;
686 int retval;
687 __u16 raw_data_length;
688 int status = urb->status;
689 unsigned long flags;
690
691 if (status) {
692 dev_dbg(&urb->dev->dev, "%s - nonzero read bulk status received: %d\n",
693 __func__, status);
694 edge_serial->read_in_progress = false;
695 return;
696 }
697
698 if (urb->actual_length == 0) {
699 dev_dbg(&urb->dev->dev, "%s - read bulk callback with no data\n", __func__);
700 edge_serial->read_in_progress = false;
701 return;
702 }
703
704 dev = &edge_serial->serial->dev->dev;
705 raw_data_length = urb->actual_length;
706
707 usb_serial_debug_data(dev, __func__, raw_data_length, data);
708
709 spin_lock_irqsave(&edge_serial->es_lock, flags);
710
711 /* decrement our rxBytes available by the number that we just got */
712 edge_serial->rxBytesAvail -= raw_data_length;
713
714 dev_dbg(dev, "%s - Received = %d, rxBytesAvail %d\n", __func__,
715 raw_data_length, edge_serial->rxBytesAvail);
716
717 process_rcvd_data(edge_serial, data, urb->actual_length);
718
719 /* check to see if there's any more data for us to read */
720 if (edge_serial->rxBytesAvail > 0) {
721 dev_dbg(dev, "%s - posting a read\n", __func__);
722 retval = usb_submit_urb(edge_serial->read_urb, GFP_ATOMIC);
723 if (retval) {
724 dev_err(dev,
725 "%s - usb_submit_urb(read bulk) failed, retval = %d\n",
726 __func__, retval);
727 edge_serial->read_in_progress = false;
728 }
729 } else {
730 edge_serial->read_in_progress = false;
731 }
732
733 spin_unlock_irqrestore(&edge_serial->es_lock, flags);
734}
735
736
737/*****************************************************************************
738 * edge_bulk_out_data_callback
739 * this is the callback function for when we have finished sending
740 * serial data on the bulk out endpoint.
741 *****************************************************************************/
742static void edge_bulk_out_data_callback(struct urb *urb)
743{
744 struct edgeport_port *edge_port = urb->context;
745 int status = urb->status;
746
747 if (status) {
748 dev_dbg(&urb->dev->dev,
749 "%s - nonzero write bulk status received: %d\n",
750 __func__, status);
751 }
752
753 if (edge_port->open)
754 tty_port_tty_wakeup(&edge_port->port->port);
755
756 /* Release the Write URB */
757 edge_port->write_in_progress = false;
758
759 /* Check if more data needs to be sent */
760 send_more_port_data((struct edgeport_serial *)
761 (usb_get_serial_data(edge_port->port->serial)), edge_port);
762}
763
764
765/*****************************************************************************
766 * BulkOutCmdCallback
767 * this is the callback function for when we have finished sending a
768 * command on the bulk out endpoint.
769 *****************************************************************************/
770static void edge_bulk_out_cmd_callback(struct urb *urb)
771{
772 struct edgeport_port *edge_port = urb->context;
773 int status = urb->status;
774
775 atomic_dec(&CmdUrbs);
776 dev_dbg(&urb->dev->dev, "%s - FREE URB %p (outstanding %d)\n",
777 __func__, urb, atomic_read(&CmdUrbs));
778
779
780 /* clean up the transfer buffer */
781 kfree(urb->transfer_buffer);
782
783 /* Free the command urb */
784 usb_free_urb(urb);
785
786 if (status) {
787 dev_dbg(&urb->dev->dev,
788 "%s - nonzero write bulk status received: %d\n",
789 __func__, status);
790 return;
791 }
792
793 /* tell the tty driver that something has changed */
794 if (edge_port->open)
795 tty_port_tty_wakeup(&edge_port->port->port);
796
797 /* we have completed the command */
798 edge_port->commandPending = false;
799 wake_up(&edge_port->wait_command);
800}
801
802
803/*****************************************************************************
804 * Driver tty interface functions
805 *****************************************************************************/
806
807/*****************************************************************************
808 * SerialOpen
809 * this function is called by the tty driver when a port is opened
810 * If successful, we return 0
811 * Otherwise we return a negative error number.
812 *****************************************************************************/
813static int edge_open(struct tty_struct *tty, struct usb_serial_port *port)
814{
815 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
816 struct device *dev = &port->dev;
817 struct usb_serial *serial;
818 struct edgeport_serial *edge_serial;
819 int response;
820
821 if (edge_port == NULL)
822 return -ENODEV;
823
824 /* see if we've set up our endpoint info yet (can't set it up
825 in edge_startup as the structures were not set up at that time.) */
826 serial = port->serial;
827 edge_serial = usb_get_serial_data(serial);
828 if (edge_serial == NULL)
829 return -ENODEV;
830 if (edge_serial->interrupt_in_buffer == NULL) {
831 struct usb_serial_port *port0 = serial->port[0];
832
833 /* not set up yet, so do it now */
834 edge_serial->interrupt_in_buffer =
835 port0->interrupt_in_buffer;
836 edge_serial->interrupt_in_endpoint =
837 port0->interrupt_in_endpointAddress;
838 edge_serial->interrupt_read_urb = port0->interrupt_in_urb;
839 edge_serial->bulk_in_buffer = port0->bulk_in_buffer;
840 edge_serial->bulk_in_endpoint =
841 port0->bulk_in_endpointAddress;
842 edge_serial->read_urb = port0->read_urb;
843 edge_serial->bulk_out_endpoint =
844 port0->bulk_out_endpointAddress;
845
846 /* set up our interrupt urb */
847 usb_fill_int_urb(edge_serial->interrupt_read_urb,
848 serial->dev,
849 usb_rcvintpipe(serial->dev,
850 port0->interrupt_in_endpointAddress),
851 port0->interrupt_in_buffer,
852 edge_serial->interrupt_read_urb->transfer_buffer_length,
853 edge_interrupt_callback, edge_serial,
854 edge_serial->interrupt_read_urb->interval);
855
856 /* set up our bulk in urb */
857 usb_fill_bulk_urb(edge_serial->read_urb, serial->dev,
858 usb_rcvbulkpipe(serial->dev,
859 port0->bulk_in_endpointAddress),
860 port0->bulk_in_buffer,
861 edge_serial->read_urb->transfer_buffer_length,
862 edge_bulk_in_callback, edge_serial);
863 edge_serial->read_in_progress = false;
864
865 /* start interrupt read for this edgeport
866 * this interrupt will continue as long
867 * as the edgeport is connected */
868 response = usb_submit_urb(edge_serial->interrupt_read_urb,
869 GFP_KERNEL);
870 if (response) {
871 dev_err(dev, "%s - Error %d submitting control urb\n",
872 __func__, response);
873 }
874 }
875
876 /* initialize our wait queues */
877 init_waitqueue_head(&edge_port->wait_open);
878 init_waitqueue_head(&edge_port->wait_chase);
879 init_waitqueue_head(&edge_port->wait_command);
880
881 /* initialize our port settings */
882 edge_port->txCredits = 0; /* Can't send any data yet */
883 /* Must always set this bit to enable ints! */
884 edge_port->shadowMCR = MCR_MASTER_IE;
885 edge_port->chaseResponsePending = false;
886
887 /* send a open port command */
888 edge_port->openPending = true;
889 edge_port->open = false;
890 response = send_iosp_ext_cmd(edge_port, IOSP_CMD_OPEN_PORT, 0);
891
892 if (response < 0) {
893 dev_err(dev, "%s - error sending open port command\n", __func__);
894 edge_port->openPending = false;
895 return -ENODEV;
896 }
897
898 /* now wait for the port to be completely opened */
899 wait_event_timeout(edge_port->wait_open, !edge_port->openPending,
900 OPEN_TIMEOUT);
901
902 if (!edge_port->open) {
903 /* open timed out */
904 dev_dbg(dev, "%s - open timeout\n", __func__);
905 edge_port->openPending = false;
906 return -ENODEV;
907 }
908
909 /* create the txfifo */
910 edge_port->txfifo.head = 0;
911 edge_port->txfifo.tail = 0;
912 edge_port->txfifo.count = 0;
913 edge_port->txfifo.size = edge_port->maxTxCredits;
914 edge_port->txfifo.fifo = kmalloc(edge_port->maxTxCredits, GFP_KERNEL);
915
916 if (!edge_port->txfifo.fifo) {
917 edge_close(port);
918 return -ENOMEM;
919 }
920
921 /* Allocate a URB for the write */
922 edge_port->write_urb = usb_alloc_urb(0, GFP_KERNEL);
923 edge_port->write_in_progress = false;
924
925 if (!edge_port->write_urb) {
926 edge_close(port);
927 return -ENOMEM;
928 }
929
930 dev_dbg(dev, "%s - Initialize TX fifo to %d bytes\n",
931 __func__, edge_port->maxTxCredits);
932
933 return 0;
934}
935
936
937/************************************************************************
938 *
939 * block_until_chase_response
940 *
941 * This function will block the close until one of the following:
942 * 1. Response to our Chase comes from Edgeport
943 * 2. A timeout of 10 seconds without activity has expired
944 * (1K of Edgeport data @ 2400 baud ==> 4 sec to empty)
945 *
946 ************************************************************************/
947static void block_until_chase_response(struct edgeport_port *edge_port)
948{
949 struct device *dev = &edge_port->port->dev;
950 DEFINE_WAIT(wait);
951 __u16 lastCredits;
952 int timeout = 1*HZ;
953 int loop = 10;
954
955 while (1) {
956 /* Save Last credits */
957 lastCredits = edge_port->txCredits;
958
959 /* Did we get our Chase response */
960 if (!edge_port->chaseResponsePending) {
961 dev_dbg(dev, "%s - Got Chase Response\n", __func__);
962
963 /* did we get all of our credit back? */
964 if (edge_port->txCredits == edge_port->maxTxCredits) {
965 dev_dbg(dev, "%s - Got all credits\n", __func__);
966 return;
967 }
968 }
969
970 /* Block the thread for a while */
971 prepare_to_wait(&edge_port->wait_chase, &wait,
972 TASK_UNINTERRUPTIBLE);
973 schedule_timeout(timeout);
974 finish_wait(&edge_port->wait_chase, &wait);
975
976 if (lastCredits == edge_port->txCredits) {
977 /* No activity.. count down. */
978 loop--;
979 if (loop == 0) {
980 edge_port->chaseResponsePending = false;
981 dev_dbg(dev, "%s - Chase TIMEOUT\n", __func__);
982 return;
983 }
984 } else {
985 /* Reset timeout value back to 10 seconds */
986 dev_dbg(dev, "%s - Last %d, Current %d\n", __func__,
987 lastCredits, edge_port->txCredits);
988 loop = 10;
989 }
990 }
991}
992
993
994/************************************************************************
995 *
996 * block_until_tx_empty
997 *
998 * This function will block the close until one of the following:
999 * 1. TX count are 0
1000 * 2. The edgeport has stopped
1001 * 3. A timeout of 3 seconds without activity has expired
1002 *
1003 ************************************************************************/
1004static void block_until_tx_empty(struct edgeport_port *edge_port)
1005{
1006 struct device *dev = &edge_port->port->dev;
1007 DEFINE_WAIT(wait);
1008 struct TxFifo *fifo = &edge_port->txfifo;
1009 __u32 lastCount;
1010 int timeout = HZ/10;
1011 int loop = 30;
1012
1013 while (1) {
1014 /* Save Last count */
1015 lastCount = fifo->count;
1016
1017 /* Is the Edgeport Buffer empty? */
1018 if (lastCount == 0) {
1019 dev_dbg(dev, "%s - TX Buffer Empty\n", __func__);
1020 return;
1021 }
1022
1023 /* Block the thread for a while */
1024 prepare_to_wait(&edge_port->wait_chase, &wait,
1025 TASK_UNINTERRUPTIBLE);
1026 schedule_timeout(timeout);
1027 finish_wait(&edge_port->wait_chase, &wait);
1028
1029 dev_dbg(dev, "%s wait\n", __func__);
1030
1031 if (lastCount == fifo->count) {
1032 /* No activity.. count down. */
1033 loop--;
1034 if (loop == 0) {
1035 dev_dbg(dev, "%s - TIMEOUT\n", __func__);
1036 return;
1037 }
1038 } else {
1039 /* Reset timeout value back to seconds */
1040 loop = 30;
1041 }
1042 }
1043}
1044
1045
1046/*****************************************************************************
1047 * edge_close
1048 * this function is called by the tty driver when a port is closed
1049 *****************************************************************************/
1050static void edge_close(struct usb_serial_port *port)
1051{
1052 struct edgeport_serial *edge_serial;
1053 struct edgeport_port *edge_port;
1054 int status;
1055
1056 edge_serial = usb_get_serial_data(port->serial);
1057 edge_port = usb_get_serial_port_data(port);
1058 if (edge_serial == NULL || edge_port == NULL)
1059 return;
1060
1061 /* block until tx is empty */
1062 block_until_tx_empty(edge_port);
1063
1064 edge_port->closePending = true;
1065
1066 if (!edge_serial->is_epic ||
1067 edge_serial->epic_descriptor.Supports.IOSPChase) {
1068 /* flush and chase */
1069 edge_port->chaseResponsePending = true;
1070
1071 dev_dbg(&port->dev, "%s - Sending IOSP_CMD_CHASE_PORT\n", __func__);
1072 status = send_iosp_ext_cmd(edge_port, IOSP_CMD_CHASE_PORT, 0);
1073 if (status == 0)
1074 /* block until chase finished */
1075 block_until_chase_response(edge_port);
1076 else
1077 edge_port->chaseResponsePending = false;
1078 }
1079
1080 if (!edge_serial->is_epic ||
1081 edge_serial->epic_descriptor.Supports.IOSPClose) {
1082 /* close the port */
1083 dev_dbg(&port->dev, "%s - Sending IOSP_CMD_CLOSE_PORT\n", __func__);
1084 send_iosp_ext_cmd(edge_port, IOSP_CMD_CLOSE_PORT, 0);
1085 }
1086
1087 /* port->close = true; */
1088 edge_port->closePending = false;
1089 edge_port->open = false;
1090 edge_port->openPending = false;
1091
1092 usb_kill_urb(edge_port->write_urb);
1093
1094 if (edge_port->write_urb) {
1095 /* if this urb had a transfer buffer already
1096 (old transfer) free it */
1097 kfree(edge_port->write_urb->transfer_buffer);
1098 usb_free_urb(edge_port->write_urb);
1099 edge_port->write_urb = NULL;
1100 }
1101 kfree(edge_port->txfifo.fifo);
1102 edge_port->txfifo.fifo = NULL;
1103}
1104
1105/*****************************************************************************
1106 * SerialWrite
1107 * this function is called by the tty driver when data should be written
1108 * to the port.
1109 * If successful, we return the number of bytes written, otherwise we
1110 * return a negative error number.
1111 *****************************************************************************/
1112static int edge_write(struct tty_struct *tty, struct usb_serial_port *port,
1113 const unsigned char *data, int count)
1114{
1115 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1116 struct TxFifo *fifo;
1117 int copySize;
1118 int bytesleft;
1119 int firsthalf;
1120 int secondhalf;
1121 unsigned long flags;
1122
1123 if (edge_port == NULL)
1124 return -ENODEV;
1125
1126 /* get a pointer to the Tx fifo */
1127 fifo = &edge_port->txfifo;
1128
1129 spin_lock_irqsave(&edge_port->ep_lock, flags);
1130
1131 /* calculate number of bytes to put in fifo */
1132 copySize = min((unsigned int)count,
1133 (edge_port->txCredits - fifo->count));
1134
1135 dev_dbg(&port->dev, "%s of %d byte(s) Fifo room %d -- will copy %d bytes\n",
1136 __func__, count, edge_port->txCredits - fifo->count, copySize);
1137
1138 /* catch writes of 0 bytes which the tty driver likes to give us,
1139 and when txCredits is empty */
1140 if (copySize == 0) {
1141 dev_dbg(&port->dev, "%s - copySize = Zero\n", __func__);
1142 goto finish_write;
1143 }
1144
1145 /* queue the data
1146 * since we can never overflow the buffer we do not have to check for a
1147 * full condition
1148 *
1149 * the copy is done is two parts -- first fill to the end of the buffer
1150 * then copy the reset from the start of the buffer
1151 */
1152 bytesleft = fifo->size - fifo->head;
1153 firsthalf = min(bytesleft, copySize);
1154 dev_dbg(&port->dev, "%s - copy %d bytes of %d into fifo \n", __func__,
1155 firsthalf, bytesleft);
1156
1157 /* now copy our data */
1158 memcpy(&fifo->fifo[fifo->head], data, firsthalf);
1159 usb_serial_debug_data(&port->dev, __func__, firsthalf, &fifo->fifo[fifo->head]);
1160
1161 /* update the index and size */
1162 fifo->head += firsthalf;
1163 fifo->count += firsthalf;
1164
1165 /* wrap the index */
1166 if (fifo->head == fifo->size)
1167 fifo->head = 0;
1168
1169 secondhalf = copySize-firsthalf;
1170
1171 if (secondhalf) {
1172 dev_dbg(&port->dev, "%s - copy rest of data %d\n", __func__, secondhalf);
1173 memcpy(&fifo->fifo[fifo->head], &data[firsthalf], secondhalf);
1174 usb_serial_debug_data(&port->dev, __func__, secondhalf, &fifo->fifo[fifo->head]);
1175 /* update the index and size */
1176 fifo->count += secondhalf;
1177 fifo->head += secondhalf;
1178 /* No need to check for wrap since we can not get to end of
1179 * the fifo in this part
1180 */
1181 }
1182
1183finish_write:
1184 spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1185
1186 send_more_port_data((struct edgeport_serial *)
1187 usb_get_serial_data(port->serial), edge_port);
1188
1189 dev_dbg(&port->dev, "%s wrote %d byte(s) TxCredits %d, Fifo %d\n",
1190 __func__, copySize, edge_port->txCredits, fifo->count);
1191
1192 return copySize;
1193}
1194
1195
1196/************************************************************************
1197 *
1198 * send_more_port_data()
1199 *
1200 * This routine attempts to write additional UART transmit data
1201 * to a port over the USB bulk pipe. It is called (1) when new
1202 * data has been written to a port's TxBuffer from higher layers
1203 * (2) when the peripheral sends us additional TxCredits indicating
1204 * that it can accept more Tx data for a given port; and (3) when
1205 * a bulk write completes successfully and we want to see if we
1206 * can transmit more.
1207 *
1208 ************************************************************************/
1209static void send_more_port_data(struct edgeport_serial *edge_serial,
1210 struct edgeport_port *edge_port)
1211{
1212 struct TxFifo *fifo = &edge_port->txfifo;
1213 struct device *dev = &edge_port->port->dev;
1214 struct urb *urb;
1215 unsigned char *buffer;
1216 int status;
1217 int count;
1218 int bytesleft;
1219 int firsthalf;
1220 int secondhalf;
1221 unsigned long flags;
1222
1223 spin_lock_irqsave(&edge_port->ep_lock, flags);
1224
1225 if (edge_port->write_in_progress ||
1226 !edge_port->open ||
1227 (fifo->count == 0)) {
1228 dev_dbg(dev, "%s EXIT - fifo %d, PendingWrite = %d\n",
1229 __func__, fifo->count, edge_port->write_in_progress);
1230 goto exit_send;
1231 }
1232
1233 /* since the amount of data in the fifo will always fit into the
1234 * edgeport buffer we do not need to check the write length
1235 *
1236 * Do we have enough credits for this port to make it worthwhile
1237 * to bother queueing a write. If it's too small, say a few bytes,
1238 * it's better to wait for more credits so we can do a larger write.
1239 */
1240 if (edge_port->txCredits < EDGE_FW_GET_TX_CREDITS_SEND_THRESHOLD(edge_port->maxTxCredits, EDGE_FW_BULK_MAX_PACKET_SIZE)) {
1241 dev_dbg(dev, "%s Not enough credit - fifo %d TxCredit %d\n",
1242 __func__, fifo->count, edge_port->txCredits);
1243 goto exit_send;
1244 }
1245
1246 /* lock this write */
1247 edge_port->write_in_progress = true;
1248
1249 /* get a pointer to the write_urb */
1250 urb = edge_port->write_urb;
1251
1252 /* make sure transfer buffer is freed */
1253 kfree(urb->transfer_buffer);
1254 urb->transfer_buffer = NULL;
1255
1256 /* build the data header for the buffer and port that we are about
1257 to send out */
1258 count = fifo->count;
1259 buffer = kmalloc(count+2, GFP_ATOMIC);
1260 if (!buffer) {
1261 edge_port->write_in_progress = false;
1262 goto exit_send;
1263 }
1264 buffer[0] = IOSP_BUILD_DATA_HDR1(edge_port->port->port_number, count);
1265 buffer[1] = IOSP_BUILD_DATA_HDR2(edge_port->port->port_number, count);
1266
1267 /* now copy our data */
1268 bytesleft = fifo->size - fifo->tail;
1269 firsthalf = min(bytesleft, count);
1270 memcpy(&buffer[2], &fifo->fifo[fifo->tail], firsthalf);
1271 fifo->tail += firsthalf;
1272 fifo->count -= firsthalf;
1273 if (fifo->tail == fifo->size)
1274 fifo->tail = 0;
1275
1276 secondhalf = count-firsthalf;
1277 if (secondhalf) {
1278 memcpy(&buffer[2+firsthalf], &fifo->fifo[fifo->tail],
1279 secondhalf);
1280 fifo->tail += secondhalf;
1281 fifo->count -= secondhalf;
1282 }
1283
1284 if (count)
1285 usb_serial_debug_data(&edge_port->port->dev, __func__, count, &buffer[2]);
1286
1287 /* fill up the urb with all of our data and submit it */
1288 usb_fill_bulk_urb(urb, edge_serial->serial->dev,
1289 usb_sndbulkpipe(edge_serial->serial->dev,
1290 edge_serial->bulk_out_endpoint),
1291 buffer, count+2,
1292 edge_bulk_out_data_callback, edge_port);
1293
1294 /* decrement the number of credits we have by the number we just sent */
1295 edge_port->txCredits -= count;
1296 edge_port->port->icount.tx += count;
1297
1298 status = usb_submit_urb(urb, GFP_ATOMIC);
1299 if (status) {
1300 /* something went wrong */
1301 dev_err_console(edge_port->port,
1302 "%s - usb_submit_urb(write bulk) failed, status = %d, data lost\n",
1303 __func__, status);
1304 edge_port->write_in_progress = false;
1305
1306 /* revert the credits as something bad happened. */
1307 edge_port->txCredits += count;
1308 edge_port->port->icount.tx -= count;
1309 }
1310 dev_dbg(dev, "%s wrote %d byte(s) TxCredit %d, Fifo %d\n",
1311 __func__, count, edge_port->txCredits, fifo->count);
1312
1313exit_send:
1314 spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1315}
1316
1317
1318/*****************************************************************************
1319 * edge_write_room
1320 * this function is called by the tty driver when it wants to know how
1321 * many bytes of data we can accept for a specific port.
1322 *****************************************************************************/
1323static unsigned int edge_write_room(struct tty_struct *tty)
1324{
1325 struct usb_serial_port *port = tty->driver_data;
1326 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1327 unsigned int room;
1328 unsigned long flags;
1329
1330 /* total of both buffers is still txCredit */
1331 spin_lock_irqsave(&edge_port->ep_lock, flags);
1332 room = edge_port->txCredits - edge_port->txfifo.count;
1333 spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1334
1335 dev_dbg(&port->dev, "%s - returns %u\n", __func__, room);
1336 return room;
1337}
1338
1339
1340/*****************************************************************************
1341 * edge_chars_in_buffer
1342 * this function is called by the tty driver when it wants to know how
1343 * many bytes of data we currently have outstanding in the port (data that
1344 * has been written, but hasn't made it out the port yet)
1345 *****************************************************************************/
1346static unsigned int edge_chars_in_buffer(struct tty_struct *tty)
1347{
1348 struct usb_serial_port *port = tty->driver_data;
1349 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1350 unsigned int num_chars;
1351 unsigned long flags;
1352
1353 spin_lock_irqsave(&edge_port->ep_lock, flags);
1354 num_chars = edge_port->maxTxCredits - edge_port->txCredits +
1355 edge_port->txfifo.count;
1356 spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1357 if (num_chars) {
1358 dev_dbg(&port->dev, "%s - returns %u\n", __func__, num_chars);
1359 }
1360
1361 return num_chars;
1362}
1363
1364
1365/*****************************************************************************
1366 * SerialThrottle
1367 * this function is called by the tty driver when it wants to stop the data
1368 * being read from the port.
1369 *****************************************************************************/
1370static void edge_throttle(struct tty_struct *tty)
1371{
1372 struct usb_serial_port *port = tty->driver_data;
1373 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1374 int status;
1375
1376 if (edge_port == NULL)
1377 return;
1378
1379 if (!edge_port->open) {
1380 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1381 return;
1382 }
1383
1384 /* if we are implementing XON/XOFF, send the stop character */
1385 if (I_IXOFF(tty)) {
1386 unsigned char stop_char = STOP_CHAR(tty);
1387 status = edge_write(tty, port, &stop_char, 1);
1388 if (status <= 0)
1389 return;
1390 }
1391
1392 /* if we are implementing RTS/CTS, toggle that line */
1393 if (C_CRTSCTS(tty)) {
1394 edge_port->shadowMCR &= ~MCR_RTS;
1395 status = send_cmd_write_uart_register(edge_port, MCR,
1396 edge_port->shadowMCR);
1397 if (status != 0)
1398 return;
1399 }
1400}
1401
1402
1403/*****************************************************************************
1404 * edge_unthrottle
1405 * this function is called by the tty driver when it wants to resume the
1406 * data being read from the port (called after SerialThrottle is called)
1407 *****************************************************************************/
1408static void edge_unthrottle(struct tty_struct *tty)
1409{
1410 struct usb_serial_port *port = tty->driver_data;
1411 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1412 int status;
1413
1414 if (edge_port == NULL)
1415 return;
1416
1417 if (!edge_port->open) {
1418 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1419 return;
1420 }
1421
1422 /* if we are implementing XON/XOFF, send the start character */
1423 if (I_IXOFF(tty)) {
1424 unsigned char start_char = START_CHAR(tty);
1425 status = edge_write(tty, port, &start_char, 1);
1426 if (status <= 0)
1427 return;
1428 }
1429 /* if we are implementing RTS/CTS, toggle that line */
1430 if (C_CRTSCTS(tty)) {
1431 edge_port->shadowMCR |= MCR_RTS;
1432 send_cmd_write_uart_register(edge_port, MCR,
1433 edge_port->shadowMCR);
1434 }
1435}
1436
1437
1438/*****************************************************************************
1439 * SerialSetTermios
1440 * this function is called by the tty driver when it wants to change
1441 * the termios structure
1442 *****************************************************************************/
1443static void edge_set_termios(struct tty_struct *tty,
1444 struct usb_serial_port *port,
1445 const struct ktermios *old_termios)
1446{
1447 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1448
1449 if (edge_port == NULL)
1450 return;
1451
1452 if (!edge_port->open) {
1453 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1454 return;
1455 }
1456
1457 /* change the port settings to the new ones specified */
1458 change_port_settings(tty, edge_port, old_termios);
1459}
1460
1461
1462/*****************************************************************************
1463 * get_lsr_info - get line status register info
1464 *
1465 * Purpose: Let user call ioctl() to get info when the UART physically
1466 * is emptied. On bus types like RS485, the transmitter must
1467 * release the bus after transmitting. This must be done when
1468 * the transmit shift register is empty, not be done when the
1469 * transmit holding register is empty. This functionality
1470 * allows an RS485 driver to be written in user space.
1471 *****************************************************************************/
1472static int get_lsr_info(struct edgeport_port *edge_port,
1473 unsigned int __user *value)
1474{
1475 unsigned int result = 0;
1476 unsigned long flags;
1477
1478 spin_lock_irqsave(&edge_port->ep_lock, flags);
1479 if (edge_port->maxTxCredits == edge_port->txCredits &&
1480 edge_port->txfifo.count == 0) {
1481 dev_dbg(&edge_port->port->dev, "%s -- Empty\n", __func__);
1482 result = TIOCSER_TEMT;
1483 }
1484 spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1485
1486 if (copy_to_user(value, &result, sizeof(int)))
1487 return -EFAULT;
1488 return 0;
1489}
1490
1491static int edge_tiocmset(struct tty_struct *tty,
1492 unsigned int set, unsigned int clear)
1493{
1494 struct usb_serial_port *port = tty->driver_data;
1495 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1496 unsigned int mcr;
1497
1498 mcr = edge_port->shadowMCR;
1499 if (set & TIOCM_RTS)
1500 mcr |= MCR_RTS;
1501 if (set & TIOCM_DTR)
1502 mcr |= MCR_DTR;
1503 if (set & TIOCM_LOOP)
1504 mcr |= MCR_LOOPBACK;
1505
1506 if (clear & TIOCM_RTS)
1507 mcr &= ~MCR_RTS;
1508 if (clear & TIOCM_DTR)
1509 mcr &= ~MCR_DTR;
1510 if (clear & TIOCM_LOOP)
1511 mcr &= ~MCR_LOOPBACK;
1512
1513 edge_port->shadowMCR = mcr;
1514
1515 send_cmd_write_uart_register(edge_port, MCR, edge_port->shadowMCR);
1516
1517 return 0;
1518}
1519
1520static int edge_tiocmget(struct tty_struct *tty)
1521{
1522 struct usb_serial_port *port = tty->driver_data;
1523 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1524 unsigned int result = 0;
1525 unsigned int msr;
1526 unsigned int mcr;
1527
1528 msr = edge_port->shadowMSR;
1529 mcr = edge_port->shadowMCR;
1530 result = ((mcr & MCR_DTR) ? TIOCM_DTR: 0) /* 0x002 */
1531 | ((mcr & MCR_RTS) ? TIOCM_RTS: 0) /* 0x004 */
1532 | ((msr & EDGEPORT_MSR_CTS) ? TIOCM_CTS: 0) /* 0x020 */
1533 | ((msr & EDGEPORT_MSR_CD) ? TIOCM_CAR: 0) /* 0x040 */
1534 | ((msr & EDGEPORT_MSR_RI) ? TIOCM_RI: 0) /* 0x080 */
1535 | ((msr & EDGEPORT_MSR_DSR) ? TIOCM_DSR: 0); /* 0x100 */
1536
1537 return result;
1538}
1539
1540/*****************************************************************************
1541 * SerialIoctl
1542 * this function handles any ioctl calls to the driver
1543 *****************************************************************************/
1544static int edge_ioctl(struct tty_struct *tty,
1545 unsigned int cmd, unsigned long arg)
1546{
1547 struct usb_serial_port *port = tty->driver_data;
1548 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1549
1550 switch (cmd) {
1551 case TIOCSERGETLSR:
1552 dev_dbg(&port->dev, "%s TIOCSERGETLSR\n", __func__);
1553 return get_lsr_info(edge_port, (unsigned int __user *) arg);
1554 }
1555 return -ENOIOCTLCMD;
1556}
1557
1558
1559/*****************************************************************************
1560 * SerialBreak
1561 * this function sends a break to the port
1562 *****************************************************************************/
1563static int edge_break(struct tty_struct *tty, int break_state)
1564{
1565 struct usb_serial_port *port = tty->driver_data;
1566 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1567 struct edgeport_serial *edge_serial = usb_get_serial_data(port->serial);
1568 int status = 0;
1569
1570 if (!edge_serial->is_epic ||
1571 edge_serial->epic_descriptor.Supports.IOSPChase) {
1572 /* flush and chase */
1573 edge_port->chaseResponsePending = true;
1574
1575 dev_dbg(&port->dev, "%s - Sending IOSP_CMD_CHASE_PORT\n", __func__);
1576 status = send_iosp_ext_cmd(edge_port, IOSP_CMD_CHASE_PORT, 0);
1577 if (status == 0) {
1578 /* block until chase finished */
1579 block_until_chase_response(edge_port);
1580 } else {
1581 edge_port->chaseResponsePending = false;
1582 }
1583 }
1584
1585 if (!edge_serial->is_epic ||
1586 edge_serial->epic_descriptor.Supports.IOSPSetClrBreak) {
1587 if (break_state == -1) {
1588 dev_dbg(&port->dev, "%s - Sending IOSP_CMD_SET_BREAK\n", __func__);
1589 status = send_iosp_ext_cmd(edge_port,
1590 IOSP_CMD_SET_BREAK, 0);
1591 } else {
1592 dev_dbg(&port->dev, "%s - Sending IOSP_CMD_CLEAR_BREAK\n", __func__);
1593 status = send_iosp_ext_cmd(edge_port,
1594 IOSP_CMD_CLEAR_BREAK, 0);
1595 }
1596 if (status)
1597 dev_dbg(&port->dev, "%s - error sending break set/clear command.\n",
1598 __func__);
1599 }
1600
1601 return status;
1602}
1603
1604
1605/*****************************************************************************
1606 * process_rcvd_data
1607 * this function handles the data received on the bulk in pipe.
1608 *****************************************************************************/
1609static void process_rcvd_data(struct edgeport_serial *edge_serial,
1610 unsigned char *buffer, __u16 bufferLength)
1611{
1612 struct usb_serial *serial = edge_serial->serial;
1613 struct device *dev = &serial->dev->dev;
1614 struct usb_serial_port *port;
1615 struct edgeport_port *edge_port;
1616 __u16 lastBufferLength;
1617 __u16 rxLen;
1618
1619 lastBufferLength = bufferLength + 1;
1620
1621 while (bufferLength > 0) {
1622 /* failsafe incase we get a message that we don't understand */
1623 if (lastBufferLength == bufferLength) {
1624 dev_dbg(dev, "%s - stuck in loop, exiting it.\n", __func__);
1625 break;
1626 }
1627 lastBufferLength = bufferLength;
1628
1629 switch (edge_serial->rxState) {
1630 case EXPECT_HDR1:
1631 edge_serial->rxHeader1 = *buffer;
1632 ++buffer;
1633 --bufferLength;
1634
1635 if (bufferLength == 0) {
1636 edge_serial->rxState = EXPECT_HDR2;
1637 break;
1638 }
1639 fallthrough;
1640 case EXPECT_HDR2:
1641 edge_serial->rxHeader2 = *buffer;
1642 ++buffer;
1643 --bufferLength;
1644
1645 dev_dbg(dev, "%s - Hdr1=%02X Hdr2=%02X\n", __func__,
1646 edge_serial->rxHeader1, edge_serial->rxHeader2);
1647 /* Process depending on whether this header is
1648 * data or status */
1649
1650 if (IS_CMD_STAT_HDR(edge_serial->rxHeader1)) {
1651 /* Decode this status header and go to
1652 * EXPECT_HDR1 (if we can process the status
1653 * with only 2 bytes), or go to EXPECT_HDR3 to
1654 * get the third byte. */
1655 edge_serial->rxPort =
1656 IOSP_GET_HDR_PORT(edge_serial->rxHeader1);
1657 edge_serial->rxStatusCode =
1658 IOSP_GET_STATUS_CODE(
1659 edge_serial->rxHeader1);
1660
1661 if (!IOSP_STATUS_IS_2BYTE(
1662 edge_serial->rxStatusCode)) {
1663 /* This status needs additional bytes.
1664 * Save what we have and then wait for
1665 * more data.
1666 */
1667 edge_serial->rxStatusParam
1668 = edge_serial->rxHeader2;
1669 edge_serial->rxState = EXPECT_HDR3;
1670 break;
1671 }
1672 /* We have all the header bytes, process the
1673 status now */
1674 process_rcvd_status(edge_serial,
1675 edge_serial->rxHeader2, 0);
1676 edge_serial->rxState = EXPECT_HDR1;
1677 break;
1678 }
1679
1680 edge_serial->rxPort = IOSP_GET_HDR_PORT(edge_serial->rxHeader1);
1681 edge_serial->rxBytesRemaining = IOSP_GET_HDR_DATA_LEN(edge_serial->rxHeader1,
1682 edge_serial->rxHeader2);
1683 dev_dbg(dev, "%s - Data for Port %u Len %u\n", __func__,
1684 edge_serial->rxPort,
1685 edge_serial->rxBytesRemaining);
1686
1687 if (bufferLength == 0) {
1688 edge_serial->rxState = EXPECT_DATA;
1689 break;
1690 }
1691 fallthrough;
1692 case EXPECT_DATA: /* Expect data */
1693 if (bufferLength < edge_serial->rxBytesRemaining) {
1694 rxLen = bufferLength;
1695 /* Expect data to start next buffer */
1696 edge_serial->rxState = EXPECT_DATA;
1697 } else {
1698 /* BufLen >= RxBytesRemaining */
1699 rxLen = edge_serial->rxBytesRemaining;
1700 /* Start another header next time */
1701 edge_serial->rxState = EXPECT_HDR1;
1702 }
1703
1704 bufferLength -= rxLen;
1705 edge_serial->rxBytesRemaining -= rxLen;
1706
1707 /* spit this data back into the tty driver if this
1708 port is open */
1709 if (rxLen && edge_serial->rxPort < serial->num_ports) {
1710 port = serial->port[edge_serial->rxPort];
1711 edge_port = usb_get_serial_port_data(port);
1712 if (edge_port && edge_port->open) {
1713 dev_dbg(dev, "%s - Sending %d bytes to TTY for port %d\n",
1714 __func__, rxLen,
1715 edge_serial->rxPort);
1716 edge_tty_recv(edge_port->port, buffer,
1717 rxLen);
1718 edge_port->port->icount.rx += rxLen;
1719 }
1720 }
1721 buffer += rxLen;
1722 break;
1723
1724 case EXPECT_HDR3: /* Expect 3rd byte of status header */
1725 edge_serial->rxHeader3 = *buffer;
1726 ++buffer;
1727 --bufferLength;
1728
1729 /* We have all the header bytes, process the
1730 status now */
1731 process_rcvd_status(edge_serial,
1732 edge_serial->rxStatusParam,
1733 edge_serial->rxHeader3);
1734 edge_serial->rxState = EXPECT_HDR1;
1735 break;
1736 }
1737 }
1738}
1739
1740
1741/*****************************************************************************
1742 * process_rcvd_status
1743 * this function handles the any status messages received on the
1744 * bulk in pipe.
1745 *****************************************************************************/
1746static void process_rcvd_status(struct edgeport_serial *edge_serial,
1747 __u8 byte2, __u8 byte3)
1748{
1749 struct usb_serial_port *port;
1750 struct edgeport_port *edge_port;
1751 struct tty_struct *tty;
1752 struct device *dev;
1753 __u8 code = edge_serial->rxStatusCode;
1754
1755 /* switch the port pointer to the one being currently talked about */
1756 if (edge_serial->rxPort >= edge_serial->serial->num_ports)
1757 return;
1758 port = edge_serial->serial->port[edge_serial->rxPort];
1759 edge_port = usb_get_serial_port_data(port);
1760 if (edge_port == NULL) {
1761 dev_err(&edge_serial->serial->dev->dev,
1762 "%s - edge_port == NULL for port %d\n",
1763 __func__, edge_serial->rxPort);
1764 return;
1765 }
1766 dev = &port->dev;
1767
1768 if (code == IOSP_EXT_STATUS) {
1769 switch (byte2) {
1770 case IOSP_EXT_STATUS_CHASE_RSP:
1771 /* we want to do EXT status regardless of port
1772 * open/closed */
1773 dev_dbg(dev, "%s - Port %u EXT CHASE_RSP Data = %02x\n",
1774 __func__, edge_serial->rxPort, byte3);
1775 /* Currently, the only EXT_STATUS is Chase, so process
1776 * here instead of one more call to one more subroutine
1777 * If/when more EXT_STATUS, there'll be more work to do
1778 * Also, we currently clear flag and close the port
1779 * regardless of content of above's Byte3.
1780 * We could choose to do something else when Byte3 says
1781 * Timeout on Chase from Edgeport, like wait longer in
1782 * block_until_chase_response, but for now we don't.
1783 */
1784 edge_port->chaseResponsePending = false;
1785 wake_up(&edge_port->wait_chase);
1786 return;
1787
1788 case IOSP_EXT_STATUS_RX_CHECK_RSP:
1789 dev_dbg(dev, "%s ========== Port %u CHECK_RSP Sequence = %02x =============\n",
1790 __func__, edge_serial->rxPort, byte3);
1791 /* Port->RxCheckRsp = true; */
1792 return;
1793 }
1794 }
1795
1796 if (code == IOSP_STATUS_OPEN_RSP) {
1797 edge_port->txCredits = GET_TX_BUFFER_SIZE(byte3);
1798 edge_port->maxTxCredits = edge_port->txCredits;
1799 dev_dbg(dev, "%s - Port %u Open Response Initial MSR = %02x TxBufferSize = %d\n",
1800 __func__, edge_serial->rxPort, byte2, edge_port->txCredits);
1801 handle_new_msr(edge_port, byte2);
1802
1803 /* send the current line settings to the port so we are
1804 in sync with any further termios calls */
1805 tty = tty_port_tty_get(&edge_port->port->port);
1806 if (tty) {
1807 change_port_settings(tty,
1808 edge_port, &tty->termios);
1809 tty_kref_put(tty);
1810 }
1811
1812 /* we have completed the open */
1813 edge_port->openPending = false;
1814 edge_port->open = true;
1815 wake_up(&edge_port->wait_open);
1816 return;
1817 }
1818
1819 /* If port is closed, silently discard all rcvd status. We can
1820 * have cases where buffered status is received AFTER the close
1821 * port command is sent to the Edgeport.
1822 */
1823 if (!edge_port->open || edge_port->closePending)
1824 return;
1825
1826 switch (code) {
1827 /* Not currently sent by Edgeport */
1828 case IOSP_STATUS_LSR:
1829 dev_dbg(dev, "%s - Port %u LSR Status = %02x\n",
1830 __func__, edge_serial->rxPort, byte2);
1831 handle_new_lsr(edge_port, false, byte2, 0);
1832 break;
1833
1834 case IOSP_STATUS_LSR_DATA:
1835 dev_dbg(dev, "%s - Port %u LSR Status = %02x, Data = %02x\n",
1836 __func__, edge_serial->rxPort, byte2, byte3);
1837 /* byte2 is LSR Register */
1838 /* byte3 is broken data byte */
1839 handle_new_lsr(edge_port, true, byte2, byte3);
1840 break;
1841 /*
1842 * case IOSP_EXT_4_STATUS:
1843 * dev_dbg(dev, "%s - Port %u LSR Status = %02x Data = %02x\n",
1844 * __func__, edge_serial->rxPort, byte2, byte3);
1845 * break;
1846 */
1847 case IOSP_STATUS_MSR:
1848 dev_dbg(dev, "%s - Port %u MSR Status = %02x\n",
1849 __func__, edge_serial->rxPort, byte2);
1850 /*
1851 * Process this new modem status and generate appropriate
1852 * events, etc, based on the new status. This routine
1853 * also saves the MSR in Port->ShadowMsr.
1854 */
1855 handle_new_msr(edge_port, byte2);
1856 break;
1857
1858 default:
1859 dev_dbg(dev, "%s - Unrecognized IOSP status code %u\n", __func__, code);
1860 break;
1861 }
1862}
1863
1864
1865/*****************************************************************************
1866 * edge_tty_recv
1867 * this function passes data on to the tty flip buffer
1868 *****************************************************************************/
1869static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data,
1870 int length)
1871{
1872 int cnt;
1873
1874 cnt = tty_insert_flip_string(&port->port, data, length);
1875 if (cnt < length) {
1876 dev_err(&port->dev, "%s - dropping data, %d bytes lost\n",
1877 __func__, length - cnt);
1878 }
1879 data += cnt;
1880 length -= cnt;
1881
1882 tty_flip_buffer_push(&port->port);
1883}
1884
1885
1886/*****************************************************************************
1887 * handle_new_msr
1888 * this function handles any change to the msr register for a port.
1889 *****************************************************************************/
1890static void handle_new_msr(struct edgeport_port *edge_port, __u8 newMsr)
1891{
1892 struct async_icount *icount;
1893
1894 if (newMsr & (EDGEPORT_MSR_DELTA_CTS | EDGEPORT_MSR_DELTA_DSR |
1895 EDGEPORT_MSR_DELTA_RI | EDGEPORT_MSR_DELTA_CD)) {
1896 icount = &edge_port->port->icount;
1897
1898 /* update input line counters */
1899 if (newMsr & EDGEPORT_MSR_DELTA_CTS)
1900 icount->cts++;
1901 if (newMsr & EDGEPORT_MSR_DELTA_DSR)
1902 icount->dsr++;
1903 if (newMsr & EDGEPORT_MSR_DELTA_CD)
1904 icount->dcd++;
1905 if (newMsr & EDGEPORT_MSR_DELTA_RI)
1906 icount->rng++;
1907 wake_up_interruptible(&edge_port->port->port.delta_msr_wait);
1908 }
1909
1910 /* Save the new modem status */
1911 edge_port->shadowMSR = newMsr & 0xf0;
1912}
1913
1914
1915/*****************************************************************************
1916 * handle_new_lsr
1917 * this function handles any change to the lsr register for a port.
1918 *****************************************************************************/
1919static void handle_new_lsr(struct edgeport_port *edge_port, __u8 lsrData,
1920 __u8 lsr, __u8 data)
1921{
1922 __u8 newLsr = (__u8) (lsr & (__u8)
1923 (LSR_OVER_ERR | LSR_PAR_ERR | LSR_FRM_ERR | LSR_BREAK));
1924 struct async_icount *icount;
1925
1926 edge_port->shadowLSR = lsr;
1927
1928 if (newLsr & LSR_BREAK) {
1929 /*
1930 * Parity and Framing errors only count if they
1931 * occur exclusive of a break being
1932 * received.
1933 */
1934 newLsr &= (__u8)(LSR_OVER_ERR | LSR_BREAK);
1935 }
1936
1937 /* Place LSR data byte into Rx buffer */
1938 if (lsrData)
1939 edge_tty_recv(edge_port->port, &data, 1);
1940
1941 /* update input line counters */
1942 icount = &edge_port->port->icount;
1943 if (newLsr & LSR_BREAK)
1944 icount->brk++;
1945 if (newLsr & LSR_OVER_ERR)
1946 icount->overrun++;
1947 if (newLsr & LSR_PAR_ERR)
1948 icount->parity++;
1949 if (newLsr & LSR_FRM_ERR)
1950 icount->frame++;
1951}
1952
1953
1954/****************************************************************************
1955 * sram_write
1956 * writes a number of bytes to the Edgeport device's sram starting at the
1957 * given address.
1958 * If successful returns the number of bytes written, otherwise it returns
1959 * a negative error number of the problem.
1960 ****************************************************************************/
1961static int sram_write(struct usb_serial *serial, __u16 extAddr, __u16 addr,
1962 __u16 length, const __u8 *data)
1963{
1964 int result;
1965 __u16 current_length;
1966 unsigned char *transfer_buffer;
1967
1968 dev_dbg(&serial->dev->dev, "%s - %x, %x, %d\n", __func__, extAddr, addr, length);
1969
1970 transfer_buffer = kmalloc(64, GFP_KERNEL);
1971 if (!transfer_buffer)
1972 return -ENOMEM;
1973
1974 /* need to split these writes up into 64 byte chunks */
1975 result = 0;
1976 while (length > 0) {
1977 if (length > 64)
1978 current_length = 64;
1979 else
1980 current_length = length;
1981
1982/* dev_dbg(&serial->dev->dev, "%s - writing %x, %x, %d\n", __func__, extAddr, addr, current_length); */
1983 memcpy(transfer_buffer, data, current_length);
1984 result = usb_control_msg(serial->dev,
1985 usb_sndctrlpipe(serial->dev, 0),
1986 USB_REQUEST_ION_WRITE_RAM,
1987 0x40, addr, extAddr, transfer_buffer,
1988 current_length, 300);
1989 if (result < 0)
1990 break;
1991 length -= current_length;
1992 addr += current_length;
1993 data += current_length;
1994 }
1995
1996 kfree(transfer_buffer);
1997 return result;
1998}
1999
2000
2001/****************************************************************************
2002 * rom_write
2003 * writes a number of bytes to the Edgeport device's ROM starting at the
2004 * given address.
2005 * If successful returns the number of bytes written, otherwise it returns
2006 * a negative error number of the problem.
2007 ****************************************************************************/
2008static int rom_write(struct usb_serial *serial, __u16 extAddr, __u16 addr,
2009 __u16 length, const __u8 *data)
2010{
2011 int result;
2012 __u16 current_length;
2013 unsigned char *transfer_buffer;
2014
2015 transfer_buffer = kmalloc(64, GFP_KERNEL);
2016 if (!transfer_buffer)
2017 return -ENOMEM;
2018
2019 /* need to split these writes up into 64 byte chunks */
2020 result = 0;
2021 while (length > 0) {
2022 if (length > 64)
2023 current_length = 64;
2024 else
2025 current_length = length;
2026 memcpy(transfer_buffer, data, current_length);
2027 result = usb_control_msg(serial->dev,
2028 usb_sndctrlpipe(serial->dev, 0),
2029 USB_REQUEST_ION_WRITE_ROM, 0x40,
2030 addr, extAddr,
2031 transfer_buffer, current_length, 300);
2032 if (result < 0)
2033 break;
2034 length -= current_length;
2035 addr += current_length;
2036 data += current_length;
2037 }
2038
2039 kfree(transfer_buffer);
2040 return result;
2041}
2042
2043
2044/****************************************************************************
2045 * rom_read
2046 * reads a number of bytes from the Edgeport device starting at the given
2047 * address.
2048 * Returns zero on success or a negative error number.
2049 ****************************************************************************/
2050static int rom_read(struct usb_serial *serial, __u16 extAddr,
2051 __u16 addr, __u16 length, __u8 *data)
2052{
2053 int result;
2054 __u16 current_length;
2055 unsigned char *transfer_buffer;
2056
2057 transfer_buffer = kmalloc(64, GFP_KERNEL);
2058 if (!transfer_buffer)
2059 return -ENOMEM;
2060
2061 /* need to split these reads up into 64 byte chunks */
2062 result = 0;
2063 while (length > 0) {
2064 if (length > 64)
2065 current_length = 64;
2066 else
2067 current_length = length;
2068 result = usb_control_msg(serial->dev,
2069 usb_rcvctrlpipe(serial->dev, 0),
2070 USB_REQUEST_ION_READ_ROM,
2071 0xC0, addr, extAddr, transfer_buffer,
2072 current_length, 300);
2073 if (result < current_length) {
2074 if (result >= 0)
2075 result = -EIO;
2076 break;
2077 }
2078 memcpy(data, transfer_buffer, current_length);
2079 length -= current_length;
2080 addr += current_length;
2081 data += current_length;
2082
2083 result = 0;
2084 }
2085
2086 kfree(transfer_buffer);
2087 return result;
2088}
2089
2090
2091/****************************************************************************
2092 * send_iosp_ext_cmd
2093 * Is used to send a IOSP message to the Edgeport device
2094 ****************************************************************************/
2095static int send_iosp_ext_cmd(struct edgeport_port *edge_port,
2096 __u8 command, __u8 param)
2097{
2098 unsigned char *buffer;
2099 unsigned char *currentCommand;
2100 int length = 0;
2101 int status = 0;
2102
2103 buffer = kmalloc(10, GFP_ATOMIC);
2104 if (!buffer)
2105 return -ENOMEM;
2106
2107 currentCommand = buffer;
2108
2109 MAKE_CMD_EXT_CMD(¤tCommand, &length, edge_port->port->port_number,
2110 command, param);
2111
2112 status = write_cmd_usb(edge_port, buffer, length);
2113 if (status) {
2114 /* something bad happened, let's free up the memory */
2115 kfree(buffer);
2116 }
2117
2118 return status;
2119}
2120
2121
2122/*****************************************************************************
2123 * write_cmd_usb
2124 * this function writes the given buffer out to the bulk write endpoint.
2125 *****************************************************************************/
2126static int write_cmd_usb(struct edgeport_port *edge_port,
2127 unsigned char *buffer, int length)
2128{
2129 struct edgeport_serial *edge_serial =
2130 usb_get_serial_data(edge_port->port->serial);
2131 struct device *dev = &edge_port->port->dev;
2132 int status = 0;
2133 struct urb *urb;
2134
2135 usb_serial_debug_data(dev, __func__, length, buffer);
2136
2137 /* Allocate our next urb */
2138 urb = usb_alloc_urb(0, GFP_ATOMIC);
2139 if (!urb)
2140 return -ENOMEM;
2141
2142 atomic_inc(&CmdUrbs);
2143 dev_dbg(dev, "%s - ALLOCATE URB %p (outstanding %d)\n",
2144 __func__, urb, atomic_read(&CmdUrbs));
2145
2146 usb_fill_bulk_urb(urb, edge_serial->serial->dev,
2147 usb_sndbulkpipe(edge_serial->serial->dev,
2148 edge_serial->bulk_out_endpoint),
2149 buffer, length, edge_bulk_out_cmd_callback, edge_port);
2150
2151 edge_port->commandPending = true;
2152 status = usb_submit_urb(urb, GFP_ATOMIC);
2153
2154 if (status) {
2155 /* something went wrong */
2156 dev_err(dev, "%s - usb_submit_urb(write command) failed, status = %d\n",
2157 __func__, status);
2158 usb_free_urb(urb);
2159 atomic_dec(&CmdUrbs);
2160 return status;
2161 }
2162
2163#if 0
2164 wait_event(&edge_port->wait_command, !edge_port->commandPending);
2165
2166 if (edge_port->commandPending) {
2167 /* command timed out */
2168 dev_dbg(dev, "%s - command timed out\n", __func__);
2169 status = -EINVAL;
2170 }
2171#endif
2172 return status;
2173}
2174
2175
2176/*****************************************************************************
2177 * send_cmd_write_baud_rate
2178 * this function sends the proper command to change the baud rate of the
2179 * specified port.
2180 *****************************************************************************/
2181static int send_cmd_write_baud_rate(struct edgeport_port *edge_port,
2182 int baudRate)
2183{
2184 struct edgeport_serial *edge_serial =
2185 usb_get_serial_data(edge_port->port->serial);
2186 struct device *dev = &edge_port->port->dev;
2187 unsigned char *cmdBuffer;
2188 unsigned char *currCmd;
2189 int cmdLen = 0;
2190 int divisor;
2191 int status;
2192 u32 number = edge_port->port->port_number;
2193
2194 if (edge_serial->is_epic &&
2195 !edge_serial->epic_descriptor.Supports.IOSPSetBaudRate) {
2196 dev_dbg(dev, "SendCmdWriteBaudRate - NOT Setting baud rate for port, baud = %d\n",
2197 baudRate);
2198 return 0;
2199 }
2200
2201 dev_dbg(dev, "%s - baud = %d\n", __func__, baudRate);
2202
2203 status = calc_baud_rate_divisor(dev, baudRate, &divisor);
2204 if (status) {
2205 dev_err(dev, "%s - bad baud rate\n", __func__);
2206 return status;
2207 }
2208
2209 /* Alloc memory for the string of commands. */
2210 cmdBuffer = kmalloc(0x100, GFP_ATOMIC);
2211 if (!cmdBuffer)
2212 return -ENOMEM;
2213
2214 currCmd = cmdBuffer;
2215
2216 /* Enable access to divisor latch */
2217 MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, LCR, LCR_DL_ENABLE);
2218
2219 /* Write the divisor itself */
2220 MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, DLL, LOW8(divisor));
2221 MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, DLM, HIGH8(divisor));
2222
2223 /* Restore original value to disable access to divisor latch */
2224 MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, LCR,
2225 edge_port->shadowLCR);
2226
2227 status = write_cmd_usb(edge_port, cmdBuffer, cmdLen);
2228 if (status) {
2229 /* something bad happened, let's free up the memory */
2230 kfree(cmdBuffer);
2231 }
2232
2233 return status;
2234}
2235
2236
2237/*****************************************************************************
2238 * calc_baud_rate_divisor
2239 * this function calculates the proper baud rate divisor for the specified
2240 * baud rate.
2241 *****************************************************************************/
2242static int calc_baud_rate_divisor(struct device *dev, int baudrate, int *divisor)
2243{
2244 int i;
2245 __u16 custom;
2246
2247 for (i = 0; i < ARRAY_SIZE(divisor_table); i++) {
2248 if (divisor_table[i].BaudRate == baudrate) {
2249 *divisor = divisor_table[i].Divisor;
2250 return 0;
2251 }
2252 }
2253
2254 /* We have tried all of the standard baud rates
2255 * lets try to calculate the divisor for this baud rate
2256 * Make sure the baud rate is reasonable */
2257 if (baudrate > 50 && baudrate < 230400) {
2258 /* get divisor */
2259 custom = (__u16)((230400L + baudrate/2) / baudrate);
2260
2261 *divisor = custom;
2262
2263 dev_dbg(dev, "%s - Baud %d = %d\n", __func__, baudrate, custom);
2264 return 0;
2265 }
2266
2267 return -1;
2268}
2269
2270
2271/*****************************************************************************
2272 * send_cmd_write_uart_register
2273 * this function builds up a uart register message and sends to the device.
2274 *****************************************************************************/
2275static int send_cmd_write_uart_register(struct edgeport_port *edge_port,
2276 __u8 regNum, __u8 regValue)
2277{
2278 struct edgeport_serial *edge_serial =
2279 usb_get_serial_data(edge_port->port->serial);
2280 struct device *dev = &edge_port->port->dev;
2281 unsigned char *cmdBuffer;
2282 unsigned char *currCmd;
2283 unsigned long cmdLen = 0;
2284 int status;
2285
2286 dev_dbg(dev, "%s - write to %s register 0x%02x\n",
2287 (regNum == MCR) ? "MCR" : "LCR", __func__, regValue);
2288
2289 if (edge_serial->is_epic &&
2290 !edge_serial->epic_descriptor.Supports.IOSPWriteMCR &&
2291 regNum == MCR) {
2292 dev_dbg(dev, "SendCmdWriteUartReg - Not writing to MCR Register\n");
2293 return 0;
2294 }
2295
2296 if (edge_serial->is_epic &&
2297 !edge_serial->epic_descriptor.Supports.IOSPWriteLCR &&
2298 regNum == LCR) {
2299 dev_dbg(dev, "SendCmdWriteUartReg - Not writing to LCR Register\n");
2300 return 0;
2301 }
2302
2303 /* Alloc memory for the string of commands. */
2304 cmdBuffer = kmalloc(0x10, GFP_ATOMIC);
2305 if (cmdBuffer == NULL)
2306 return -ENOMEM;
2307
2308 currCmd = cmdBuffer;
2309
2310 /* Build a cmd in the buffer to write the given register */
2311 MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, edge_port->port->port_number,
2312 regNum, regValue);
2313
2314 status = write_cmd_usb(edge_port, cmdBuffer, cmdLen);
2315 if (status) {
2316 /* something bad happened, let's free up the memory */
2317 kfree(cmdBuffer);
2318 }
2319
2320 return status;
2321}
2322
2323
2324/*****************************************************************************
2325 * change_port_settings
2326 * This routine is called to set the UART on the device to match the
2327 * specified new settings.
2328 *****************************************************************************/
2329
2330static void change_port_settings(struct tty_struct *tty,
2331 struct edgeport_port *edge_port, const struct ktermios *old_termios)
2332{
2333 struct device *dev = &edge_port->port->dev;
2334 struct edgeport_serial *edge_serial =
2335 usb_get_serial_data(edge_port->port->serial);
2336 int baud;
2337 unsigned cflag;
2338 __u8 mask = 0xff;
2339 __u8 lData;
2340 __u8 lParity;
2341 __u8 lStop;
2342 __u8 rxFlow;
2343 __u8 txFlow;
2344 int status;
2345
2346 if (!edge_port->open &&
2347 !edge_port->openPending) {
2348 dev_dbg(dev, "%s - port not opened\n", __func__);
2349 return;
2350 }
2351
2352 cflag = tty->termios.c_cflag;
2353
2354 switch (cflag & CSIZE) {
2355 case CS5:
2356 lData = LCR_BITS_5; mask = 0x1f;
2357 dev_dbg(dev, "%s - data bits = 5\n", __func__);
2358 break;
2359 case CS6:
2360 lData = LCR_BITS_6; mask = 0x3f;
2361 dev_dbg(dev, "%s - data bits = 6\n", __func__);
2362 break;
2363 case CS7:
2364 lData = LCR_BITS_7; mask = 0x7f;
2365 dev_dbg(dev, "%s - data bits = 7\n", __func__);
2366 break;
2367 default:
2368 case CS8:
2369 lData = LCR_BITS_8;
2370 dev_dbg(dev, "%s - data bits = 8\n", __func__);
2371 break;
2372 }
2373
2374 lParity = LCR_PAR_NONE;
2375 if (cflag & PARENB) {
2376 if (cflag & CMSPAR) {
2377 if (cflag & PARODD) {
2378 lParity = LCR_PAR_MARK;
2379 dev_dbg(dev, "%s - parity = mark\n", __func__);
2380 } else {
2381 lParity = LCR_PAR_SPACE;
2382 dev_dbg(dev, "%s - parity = space\n", __func__);
2383 }
2384 } else if (cflag & PARODD) {
2385 lParity = LCR_PAR_ODD;
2386 dev_dbg(dev, "%s - parity = odd\n", __func__);
2387 } else {
2388 lParity = LCR_PAR_EVEN;
2389 dev_dbg(dev, "%s - parity = even\n", __func__);
2390 }
2391 } else {
2392 dev_dbg(dev, "%s - parity = none\n", __func__);
2393 }
2394
2395 if (cflag & CSTOPB) {
2396 lStop = LCR_STOP_2;
2397 dev_dbg(dev, "%s - stop bits = 2\n", __func__);
2398 } else {
2399 lStop = LCR_STOP_1;
2400 dev_dbg(dev, "%s - stop bits = 1\n", __func__);
2401 }
2402
2403 /* figure out the flow control settings */
2404 rxFlow = txFlow = 0x00;
2405 if (cflag & CRTSCTS) {
2406 rxFlow |= IOSP_RX_FLOW_RTS;
2407 txFlow |= IOSP_TX_FLOW_CTS;
2408 dev_dbg(dev, "%s - RTS/CTS is enabled\n", __func__);
2409 } else {
2410 dev_dbg(dev, "%s - RTS/CTS is disabled\n", __func__);
2411 }
2412
2413 /* if we are implementing XON/XOFF, set the start and stop character
2414 in the device */
2415 if (I_IXOFF(tty) || I_IXON(tty)) {
2416 unsigned char stop_char = STOP_CHAR(tty);
2417 unsigned char start_char = START_CHAR(tty);
2418
2419 if (!edge_serial->is_epic ||
2420 edge_serial->epic_descriptor.Supports.IOSPSetXChar) {
2421 send_iosp_ext_cmd(edge_port,
2422 IOSP_CMD_SET_XON_CHAR, start_char);
2423 send_iosp_ext_cmd(edge_port,
2424 IOSP_CMD_SET_XOFF_CHAR, stop_char);
2425 }
2426
2427 /* if we are implementing INBOUND XON/XOFF */
2428 if (I_IXOFF(tty)) {
2429 rxFlow |= IOSP_RX_FLOW_XON_XOFF;
2430 dev_dbg(dev, "%s - INBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n",
2431 __func__, start_char, stop_char);
2432 } else {
2433 dev_dbg(dev, "%s - INBOUND XON/XOFF is disabled\n", __func__);
2434 }
2435
2436 /* if we are implementing OUTBOUND XON/XOFF */
2437 if (I_IXON(tty)) {
2438 txFlow |= IOSP_TX_FLOW_XON_XOFF;
2439 dev_dbg(dev, "%s - OUTBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n",
2440 __func__, start_char, stop_char);
2441 } else {
2442 dev_dbg(dev, "%s - OUTBOUND XON/XOFF is disabled\n", __func__);
2443 }
2444 }
2445
2446 /* Set flow control to the configured value */
2447 if (!edge_serial->is_epic ||
2448 edge_serial->epic_descriptor.Supports.IOSPSetRxFlow)
2449 send_iosp_ext_cmd(edge_port, IOSP_CMD_SET_RX_FLOW, rxFlow);
2450 if (!edge_serial->is_epic ||
2451 edge_serial->epic_descriptor.Supports.IOSPSetTxFlow)
2452 send_iosp_ext_cmd(edge_port, IOSP_CMD_SET_TX_FLOW, txFlow);
2453
2454
2455 edge_port->shadowLCR &= ~(LCR_BITS_MASK | LCR_STOP_MASK | LCR_PAR_MASK);
2456 edge_port->shadowLCR |= (lData | lParity | lStop);
2457
2458 edge_port->validDataMask = mask;
2459
2460 /* Send the updated LCR value to the EdgePort */
2461 status = send_cmd_write_uart_register(edge_port, LCR,
2462 edge_port->shadowLCR);
2463 if (status != 0)
2464 return;
2465
2466 /* set up the MCR register and send it to the EdgePort */
2467 edge_port->shadowMCR = MCR_MASTER_IE;
2468 if (cflag & CBAUD)
2469 edge_port->shadowMCR |= (MCR_DTR | MCR_RTS);
2470
2471 status = send_cmd_write_uart_register(edge_port, MCR,
2472 edge_port->shadowMCR);
2473 if (status != 0)
2474 return;
2475
2476 /* Determine divisor based on baud rate */
2477 baud = tty_get_baud_rate(tty);
2478 if (!baud) {
2479 /* pick a default, any default... */
2480 baud = 9600;
2481 }
2482
2483 dev_dbg(dev, "%s - baud rate = %d\n", __func__, baud);
2484 status = send_cmd_write_baud_rate(edge_port, baud);
2485 if (status == -1) {
2486 /* Speed change was not possible - put back the old speed */
2487 baud = tty_termios_baud_rate(old_termios);
2488 tty_encode_baud_rate(tty, baud, baud);
2489 }
2490}
2491
2492
2493/****************************************************************************
2494 * unicode_to_ascii
2495 * Turns a string from Unicode into ASCII.
2496 * Doesn't do a good job with any characters that are outside the normal
2497 * ASCII range, but it's only for debugging...
2498 * NOTE: expects the unicode in LE format
2499 ****************************************************************************/
2500static void unicode_to_ascii(char *string, int buflen,
2501 __le16 *unicode, int unicode_size)
2502{
2503 int i;
2504
2505 if (buflen <= 0) /* never happens, but... */
2506 return;
2507 --buflen; /* space for nul */
2508
2509 for (i = 0; i < unicode_size; i++) {
2510 if (i >= buflen)
2511 break;
2512 string[i] = (char)(le16_to_cpu(unicode[i]));
2513 }
2514 string[i] = 0x00;
2515}
2516
2517
2518/****************************************************************************
2519 * get_manufacturing_desc
2520 * reads in the manufacturing descriptor and stores it into the serial
2521 * structure.
2522 ****************************************************************************/
2523static void get_manufacturing_desc(struct edgeport_serial *edge_serial)
2524{
2525 struct device *dev = &edge_serial->serial->dev->dev;
2526 int response;
2527
2528 dev_dbg(dev, "getting manufacturer descriptor\n");
2529
2530 response = rom_read(edge_serial->serial,
2531 (EDGE_MANUF_DESC_ADDR & 0xffff0000) >> 16,
2532 (__u16)(EDGE_MANUF_DESC_ADDR & 0x0000ffff),
2533 EDGE_MANUF_DESC_LEN,
2534 (__u8 *)(&edge_serial->manuf_descriptor));
2535
2536 if (response < 0) {
2537 dev_err(dev, "error in getting manufacturer descriptor: %d\n",
2538 response);
2539 } else {
2540 char string[30];
2541 dev_dbg(dev, "**Manufacturer Descriptor\n");
2542 dev_dbg(dev, " RomSize: %dK\n",
2543 edge_serial->manuf_descriptor.RomSize);
2544 dev_dbg(dev, " RamSize: %dK\n",
2545 edge_serial->manuf_descriptor.RamSize);
2546 dev_dbg(dev, " CpuRev: %d\n",
2547 edge_serial->manuf_descriptor.CpuRev);
2548 dev_dbg(dev, " BoardRev: %d\n",
2549 edge_serial->manuf_descriptor.BoardRev);
2550 dev_dbg(dev, " NumPorts: %d\n",
2551 edge_serial->manuf_descriptor.NumPorts);
2552 dev_dbg(dev, " DescDate: %d/%d/%d\n",
2553 edge_serial->manuf_descriptor.DescDate[0],
2554 edge_serial->manuf_descriptor.DescDate[1],
2555 edge_serial->manuf_descriptor.DescDate[2]+1900);
2556 unicode_to_ascii(string, sizeof(string),
2557 edge_serial->manuf_descriptor.SerialNumber,
2558 edge_serial->manuf_descriptor.SerNumLength/2);
2559 dev_dbg(dev, " SerialNumber: %s\n", string);
2560 unicode_to_ascii(string, sizeof(string),
2561 edge_serial->manuf_descriptor.AssemblyNumber,
2562 edge_serial->manuf_descriptor.AssemblyNumLength/2);
2563 dev_dbg(dev, " AssemblyNumber: %s\n", string);
2564 unicode_to_ascii(string, sizeof(string),
2565 edge_serial->manuf_descriptor.OemAssyNumber,
2566 edge_serial->manuf_descriptor.OemAssyNumLength/2);
2567 dev_dbg(dev, " OemAssyNumber: %s\n", string);
2568 dev_dbg(dev, " UartType: %d\n",
2569 edge_serial->manuf_descriptor.UartType);
2570 dev_dbg(dev, " IonPid: %d\n",
2571 edge_serial->manuf_descriptor.IonPid);
2572 dev_dbg(dev, " IonConfig: %d\n",
2573 edge_serial->manuf_descriptor.IonConfig);
2574 }
2575}
2576
2577
2578/****************************************************************************
2579 * get_boot_desc
2580 * reads in the bootloader descriptor and stores it into the serial
2581 * structure.
2582 ****************************************************************************/
2583static void get_boot_desc(struct edgeport_serial *edge_serial)
2584{
2585 struct device *dev = &edge_serial->serial->dev->dev;
2586 int response;
2587
2588 dev_dbg(dev, "getting boot descriptor\n");
2589
2590 response = rom_read(edge_serial->serial,
2591 (EDGE_BOOT_DESC_ADDR & 0xffff0000) >> 16,
2592 (__u16)(EDGE_BOOT_DESC_ADDR & 0x0000ffff),
2593 EDGE_BOOT_DESC_LEN,
2594 (__u8 *)(&edge_serial->boot_descriptor));
2595
2596 if (response < 0) {
2597 dev_err(dev, "error in getting boot descriptor: %d\n",
2598 response);
2599 } else {
2600 dev_dbg(dev, "**Boot Descriptor:\n");
2601 dev_dbg(dev, " BootCodeLength: %d\n",
2602 le16_to_cpu(edge_serial->boot_descriptor.BootCodeLength));
2603 dev_dbg(dev, " MajorVersion: %d\n",
2604 edge_serial->boot_descriptor.MajorVersion);
2605 dev_dbg(dev, " MinorVersion: %d\n",
2606 edge_serial->boot_descriptor.MinorVersion);
2607 dev_dbg(dev, " BuildNumber: %d\n",
2608 le16_to_cpu(edge_serial->boot_descriptor.BuildNumber));
2609 dev_dbg(dev, " Capabilities: 0x%x\n",
2610 le16_to_cpu(edge_serial->boot_descriptor.Capabilities));
2611 dev_dbg(dev, " UConfig0: %d\n",
2612 edge_serial->boot_descriptor.UConfig0);
2613 dev_dbg(dev, " UConfig1: %d\n",
2614 edge_serial->boot_descriptor.UConfig1);
2615 }
2616}
2617
2618
2619/****************************************************************************
2620 * load_application_firmware
2621 * This is called to load the application firmware to the device
2622 ****************************************************************************/
2623static void load_application_firmware(struct edgeport_serial *edge_serial)
2624{
2625 struct device *dev = &edge_serial->serial->dev->dev;
2626 const struct ihex_binrec *rec;
2627 const struct firmware *fw;
2628 const char *fw_name;
2629 const char *fw_info;
2630 int response;
2631 __u32 Operaddr;
2632 __u16 build;
2633
2634 switch (edge_serial->product_info.iDownloadFile) {
2635 case EDGE_DOWNLOAD_FILE_I930:
2636 fw_info = "downloading firmware version (930)";
2637 fw_name = "edgeport/down.fw";
2638 break;
2639
2640 case EDGE_DOWNLOAD_FILE_80251:
2641 fw_info = "downloading firmware version (80251)";
2642 fw_name = "edgeport/down2.fw";
2643 break;
2644
2645 case EDGE_DOWNLOAD_FILE_NONE:
2646 dev_dbg(dev, "No download file specified, skipping download\n");
2647 return;
2648
2649 default:
2650 return;
2651 }
2652
2653 response = request_ihex_firmware(&fw, fw_name,
2654 &edge_serial->serial->dev->dev);
2655 if (response) {
2656 dev_err(dev, "Failed to load image \"%s\" err %d\n",
2657 fw_name, response);
2658 return;
2659 }
2660
2661 rec = (const struct ihex_binrec *)fw->data;
2662 build = (rec->data[2] << 8) | rec->data[3];
2663
2664 dev_dbg(dev, "%s %d.%d.%d\n", fw_info, rec->data[0], rec->data[1], build);
2665
2666 edge_serial->product_info.FirmwareMajorVersion = rec->data[0];
2667 edge_serial->product_info.FirmwareMinorVersion = rec->data[1];
2668 edge_serial->product_info.FirmwareBuildNumber = cpu_to_le16(build);
2669
2670 for (rec = ihex_next_binrec(rec); rec;
2671 rec = ihex_next_binrec(rec)) {
2672 Operaddr = be32_to_cpu(rec->addr);
2673 response = sram_write(edge_serial->serial,
2674 Operaddr >> 16,
2675 Operaddr & 0xFFFF,
2676 be16_to_cpu(rec->len),
2677 &rec->data[0]);
2678 if (response < 0) {
2679 dev_err(&edge_serial->serial->dev->dev,
2680 "sram_write failed (%x, %x, %d)\n",
2681 Operaddr >> 16, Operaddr & 0xFFFF,
2682 be16_to_cpu(rec->len));
2683 break;
2684 }
2685 }
2686
2687 dev_dbg(dev, "sending exec_dl_code\n");
2688 response = usb_control_msg (edge_serial->serial->dev,
2689 usb_sndctrlpipe(edge_serial->serial->dev, 0),
2690 USB_REQUEST_ION_EXEC_DL_CODE,
2691 0x40, 0x4000, 0x0001, NULL, 0, 3000);
2692
2693 release_firmware(fw);
2694}
2695
2696
2697/****************************************************************************
2698 * edge_startup
2699 ****************************************************************************/
2700static int edge_startup(struct usb_serial *serial)
2701{
2702 struct edgeport_serial *edge_serial;
2703 struct usb_device *dev;
2704 struct device *ddev = &serial->dev->dev;
2705 int i;
2706 int response;
2707 bool interrupt_in_found;
2708 bool bulk_in_found;
2709 bool bulk_out_found;
2710 static const __u32 descriptor[3] = { EDGE_COMPATIBILITY_MASK0,
2711 EDGE_COMPATIBILITY_MASK1,
2712 EDGE_COMPATIBILITY_MASK2 };
2713
2714 dev = serial->dev;
2715
2716 /* create our private serial structure */
2717 edge_serial = kzalloc(sizeof(struct edgeport_serial), GFP_KERNEL);
2718 if (!edge_serial)
2719 return -ENOMEM;
2720
2721 spin_lock_init(&edge_serial->es_lock);
2722 edge_serial->serial = serial;
2723 usb_set_serial_data(serial, edge_serial);
2724
2725 /* get the name for the device from the device */
2726 i = usb_string(dev, dev->descriptor.iManufacturer,
2727 &edge_serial->name[0], MAX_NAME_LEN+1);
2728 if (i < 0)
2729 i = 0;
2730 edge_serial->name[i++] = ' ';
2731 usb_string(dev, dev->descriptor.iProduct,
2732 &edge_serial->name[i], MAX_NAME_LEN+2 - i);
2733
2734 dev_info(&serial->dev->dev, "%s detected\n", edge_serial->name);
2735
2736 /* Read the epic descriptor */
2737 if (get_epic_descriptor(edge_serial) < 0) {
2738 /* memcpy descriptor to Supports structures */
2739 memcpy(&edge_serial->epic_descriptor.Supports, descriptor,
2740 sizeof(struct edge_compatibility_bits));
2741
2742 /* get the manufacturing descriptor for this device */
2743 get_manufacturing_desc(edge_serial);
2744
2745 /* get the boot descriptor */
2746 get_boot_desc(edge_serial);
2747
2748 get_product_info(edge_serial);
2749 }
2750
2751 /* set the number of ports from the manufacturing description */
2752 /* serial->num_ports = serial->product_info.NumPorts; */
2753 if ((!edge_serial->is_epic) &&
2754 (edge_serial->product_info.NumPorts != serial->num_ports)) {
2755 dev_warn(ddev,
2756 "Device Reported %d serial ports vs. core thinking we have %d ports, email greg@kroah.com this information.\n",
2757 edge_serial->product_info.NumPorts,
2758 serial->num_ports);
2759 }
2760
2761 dev_dbg(ddev, "%s - time 1 %ld\n", __func__, jiffies);
2762
2763 /* If not an EPiC device */
2764 if (!edge_serial->is_epic) {
2765 /* now load the application firmware into this device */
2766 load_application_firmware(edge_serial);
2767
2768 dev_dbg(ddev, "%s - time 2 %ld\n", __func__, jiffies);
2769
2770 /* Check current Edgeport EEPROM and update if necessary */
2771 update_edgeport_E2PROM(edge_serial);
2772
2773 dev_dbg(ddev, "%s - time 3 %ld\n", __func__, jiffies);
2774
2775 /* set the configuration to use #1 */
2776/* dev_dbg(ddev, "set_configuration 1\n"); */
2777/* usb_set_configuration (dev, 1); */
2778 }
2779 dev_dbg(ddev, " FirmwareMajorVersion %d.%d.%d\n",
2780 edge_serial->product_info.FirmwareMajorVersion,
2781 edge_serial->product_info.FirmwareMinorVersion,
2782 le16_to_cpu(edge_serial->product_info.FirmwareBuildNumber));
2783
2784 /* we set up the pointers to the endpoints in the edge_open function,
2785 * as the structures aren't created yet. */
2786
2787 response = 0;
2788
2789 if (edge_serial->is_epic) {
2790 struct usb_host_interface *alt;
2791
2792 alt = serial->interface->cur_altsetting;
2793
2794 /* EPIC thing, set up our interrupt polling now and our read
2795 * urb, so that the device knows it really is connected. */
2796 interrupt_in_found = bulk_in_found = bulk_out_found = false;
2797 for (i = 0; i < alt->desc.bNumEndpoints; ++i) {
2798 struct usb_endpoint_descriptor *endpoint;
2799 int buffer_size;
2800
2801 endpoint = &alt->endpoint[i].desc;
2802 buffer_size = usb_endpoint_maxp(endpoint);
2803 if (!interrupt_in_found &&
2804 (usb_endpoint_is_int_in(endpoint))) {
2805 /* we found a interrupt in endpoint */
2806 dev_dbg(ddev, "found interrupt in\n");
2807
2808 /* not set up yet, so do it now */
2809 edge_serial->interrupt_read_urb =
2810 usb_alloc_urb(0, GFP_KERNEL);
2811 if (!edge_serial->interrupt_read_urb) {
2812 response = -ENOMEM;
2813 break;
2814 }
2815
2816 edge_serial->interrupt_in_buffer =
2817 kmalloc(buffer_size, GFP_KERNEL);
2818 if (!edge_serial->interrupt_in_buffer) {
2819 response = -ENOMEM;
2820 break;
2821 }
2822 edge_serial->interrupt_in_endpoint =
2823 endpoint->bEndpointAddress;
2824
2825 /* set up our interrupt urb */
2826 usb_fill_int_urb(
2827 edge_serial->interrupt_read_urb,
2828 dev,
2829 usb_rcvintpipe(dev,
2830 endpoint->bEndpointAddress),
2831 edge_serial->interrupt_in_buffer,
2832 buffer_size,
2833 edge_interrupt_callback,
2834 edge_serial,
2835 endpoint->bInterval);
2836
2837 interrupt_in_found = true;
2838 }
2839
2840 if (!bulk_in_found &&
2841 (usb_endpoint_is_bulk_in(endpoint))) {
2842 /* we found a bulk in endpoint */
2843 dev_dbg(ddev, "found bulk in\n");
2844
2845 /* not set up yet, so do it now */
2846 edge_serial->read_urb =
2847 usb_alloc_urb(0, GFP_KERNEL);
2848 if (!edge_serial->read_urb) {
2849 response = -ENOMEM;
2850 break;
2851 }
2852
2853 edge_serial->bulk_in_buffer =
2854 kmalloc(buffer_size, GFP_KERNEL);
2855 if (!edge_serial->bulk_in_buffer) {
2856 response = -ENOMEM;
2857 break;
2858 }
2859 edge_serial->bulk_in_endpoint =
2860 endpoint->bEndpointAddress;
2861
2862 /* set up our bulk in urb */
2863 usb_fill_bulk_urb(edge_serial->read_urb, dev,
2864 usb_rcvbulkpipe(dev,
2865 endpoint->bEndpointAddress),
2866 edge_serial->bulk_in_buffer,
2867 usb_endpoint_maxp(endpoint),
2868 edge_bulk_in_callback,
2869 edge_serial);
2870 bulk_in_found = true;
2871 }
2872
2873 if (!bulk_out_found &&
2874 (usb_endpoint_is_bulk_out(endpoint))) {
2875 /* we found a bulk out endpoint */
2876 dev_dbg(ddev, "found bulk out\n");
2877 edge_serial->bulk_out_endpoint =
2878 endpoint->bEndpointAddress;
2879 bulk_out_found = true;
2880 }
2881 }
2882
2883 if (response || !interrupt_in_found || !bulk_in_found ||
2884 !bulk_out_found) {
2885 if (!response) {
2886 dev_err(ddev, "expected endpoints not found\n");
2887 response = -ENODEV;
2888 }
2889
2890 goto error;
2891 }
2892
2893 /* start interrupt read for this edgeport this interrupt will
2894 * continue as long as the edgeport is connected */
2895 response = usb_submit_urb(edge_serial->interrupt_read_urb,
2896 GFP_KERNEL);
2897 if (response) {
2898 dev_err(ddev, "%s - Error %d submitting control urb\n",
2899 __func__, response);
2900
2901 goto error;
2902 }
2903 }
2904 return response;
2905
2906error:
2907 usb_free_urb(edge_serial->interrupt_read_urb);
2908 kfree(edge_serial->interrupt_in_buffer);
2909
2910 usb_free_urb(edge_serial->read_urb);
2911 kfree(edge_serial->bulk_in_buffer);
2912
2913 kfree(edge_serial);
2914
2915 return response;
2916}
2917
2918
2919/****************************************************************************
2920 * edge_disconnect
2921 * This function is called whenever the device is removed from the usb bus.
2922 ****************************************************************************/
2923static void edge_disconnect(struct usb_serial *serial)
2924{
2925 struct edgeport_serial *edge_serial = usb_get_serial_data(serial);
2926
2927 if (edge_serial->is_epic) {
2928 usb_kill_urb(edge_serial->interrupt_read_urb);
2929 usb_kill_urb(edge_serial->read_urb);
2930 }
2931}
2932
2933
2934/****************************************************************************
2935 * edge_release
2936 * This function is called when the device structure is deallocated.
2937 ****************************************************************************/
2938static void edge_release(struct usb_serial *serial)
2939{
2940 struct edgeport_serial *edge_serial = usb_get_serial_data(serial);
2941
2942 if (edge_serial->is_epic) {
2943 usb_kill_urb(edge_serial->interrupt_read_urb);
2944 usb_free_urb(edge_serial->interrupt_read_urb);
2945 kfree(edge_serial->interrupt_in_buffer);
2946
2947 usb_kill_urb(edge_serial->read_urb);
2948 usb_free_urb(edge_serial->read_urb);
2949 kfree(edge_serial->bulk_in_buffer);
2950 }
2951
2952 kfree(edge_serial);
2953}
2954
2955static int edge_port_probe(struct usb_serial_port *port)
2956{
2957 struct edgeport_port *edge_port;
2958
2959 edge_port = kzalloc(sizeof(*edge_port), GFP_KERNEL);
2960 if (!edge_port)
2961 return -ENOMEM;
2962
2963 spin_lock_init(&edge_port->ep_lock);
2964 edge_port->port = port;
2965
2966 usb_set_serial_port_data(port, edge_port);
2967
2968 return 0;
2969}
2970
2971static void edge_port_remove(struct usb_serial_port *port)
2972{
2973 struct edgeport_port *edge_port;
2974
2975 edge_port = usb_get_serial_port_data(port);
2976 kfree(edge_port);
2977}
2978
2979static struct usb_serial_driver edgeport_2port_device = {
2980 .driver = {
2981 .owner = THIS_MODULE,
2982 .name = "edgeport_2",
2983 },
2984 .description = "Edgeport 2 port adapter",
2985 .id_table = edgeport_2port_id_table,
2986 .num_ports = 2,
2987 .num_bulk_in = 1,
2988 .num_bulk_out = 1,
2989 .num_interrupt_in = 1,
2990 .open = edge_open,
2991 .close = edge_close,
2992 .throttle = edge_throttle,
2993 .unthrottle = edge_unthrottle,
2994 .attach = edge_startup,
2995 .disconnect = edge_disconnect,
2996 .release = edge_release,
2997 .port_probe = edge_port_probe,
2998 .port_remove = edge_port_remove,
2999 .ioctl = edge_ioctl,
3000 .set_termios = edge_set_termios,
3001 .tiocmget = edge_tiocmget,
3002 .tiocmset = edge_tiocmset,
3003 .tiocmiwait = usb_serial_generic_tiocmiwait,
3004 .get_icount = usb_serial_generic_get_icount,
3005 .write = edge_write,
3006 .write_room = edge_write_room,
3007 .chars_in_buffer = edge_chars_in_buffer,
3008 .break_ctl = edge_break,
3009 .read_int_callback = edge_interrupt_callback,
3010 .read_bulk_callback = edge_bulk_in_callback,
3011 .write_bulk_callback = edge_bulk_out_data_callback,
3012};
3013
3014static struct usb_serial_driver edgeport_4port_device = {
3015 .driver = {
3016 .owner = THIS_MODULE,
3017 .name = "edgeport_4",
3018 },
3019 .description = "Edgeport 4 port adapter",
3020 .id_table = edgeport_4port_id_table,
3021 .num_ports = 4,
3022 .num_bulk_in = 1,
3023 .num_bulk_out = 1,
3024 .num_interrupt_in = 1,
3025 .open = edge_open,
3026 .close = edge_close,
3027 .throttle = edge_throttle,
3028 .unthrottle = edge_unthrottle,
3029 .attach = edge_startup,
3030 .disconnect = edge_disconnect,
3031 .release = edge_release,
3032 .port_probe = edge_port_probe,
3033 .port_remove = edge_port_remove,
3034 .ioctl = edge_ioctl,
3035 .set_termios = edge_set_termios,
3036 .tiocmget = edge_tiocmget,
3037 .tiocmset = edge_tiocmset,
3038 .tiocmiwait = usb_serial_generic_tiocmiwait,
3039 .get_icount = usb_serial_generic_get_icount,
3040 .write = edge_write,
3041 .write_room = edge_write_room,
3042 .chars_in_buffer = edge_chars_in_buffer,
3043 .break_ctl = edge_break,
3044 .read_int_callback = edge_interrupt_callback,
3045 .read_bulk_callback = edge_bulk_in_callback,
3046 .write_bulk_callback = edge_bulk_out_data_callback,
3047};
3048
3049static struct usb_serial_driver edgeport_8port_device = {
3050 .driver = {
3051 .owner = THIS_MODULE,
3052 .name = "edgeport_8",
3053 },
3054 .description = "Edgeport 8 port adapter",
3055 .id_table = edgeport_8port_id_table,
3056 .num_ports = 8,
3057 .num_bulk_in = 1,
3058 .num_bulk_out = 1,
3059 .num_interrupt_in = 1,
3060 .open = edge_open,
3061 .close = edge_close,
3062 .throttle = edge_throttle,
3063 .unthrottle = edge_unthrottle,
3064 .attach = edge_startup,
3065 .disconnect = edge_disconnect,
3066 .release = edge_release,
3067 .port_probe = edge_port_probe,
3068 .port_remove = edge_port_remove,
3069 .ioctl = edge_ioctl,
3070 .set_termios = edge_set_termios,
3071 .tiocmget = edge_tiocmget,
3072 .tiocmset = edge_tiocmset,
3073 .tiocmiwait = usb_serial_generic_tiocmiwait,
3074 .get_icount = usb_serial_generic_get_icount,
3075 .write = edge_write,
3076 .write_room = edge_write_room,
3077 .chars_in_buffer = edge_chars_in_buffer,
3078 .break_ctl = edge_break,
3079 .read_int_callback = edge_interrupt_callback,
3080 .read_bulk_callback = edge_bulk_in_callback,
3081 .write_bulk_callback = edge_bulk_out_data_callback,
3082};
3083
3084static struct usb_serial_driver epic_device = {
3085 .driver = {
3086 .owner = THIS_MODULE,
3087 .name = "epic",
3088 },
3089 .description = "EPiC device",
3090 .id_table = Epic_port_id_table,
3091 .num_ports = 1,
3092 .num_bulk_in = 1,
3093 .num_bulk_out = 1,
3094 .num_interrupt_in = 1,
3095 .open = edge_open,
3096 .close = edge_close,
3097 .throttle = edge_throttle,
3098 .unthrottle = edge_unthrottle,
3099 .attach = edge_startup,
3100 .disconnect = edge_disconnect,
3101 .release = edge_release,
3102 .port_probe = edge_port_probe,
3103 .port_remove = edge_port_remove,
3104 .ioctl = edge_ioctl,
3105 .set_termios = edge_set_termios,
3106 .tiocmget = edge_tiocmget,
3107 .tiocmset = edge_tiocmset,
3108 .tiocmiwait = usb_serial_generic_tiocmiwait,
3109 .get_icount = usb_serial_generic_get_icount,
3110 .write = edge_write,
3111 .write_room = edge_write_room,
3112 .chars_in_buffer = edge_chars_in_buffer,
3113 .break_ctl = edge_break,
3114 .read_int_callback = edge_interrupt_callback,
3115 .read_bulk_callback = edge_bulk_in_callback,
3116 .write_bulk_callback = edge_bulk_out_data_callback,
3117};
3118
3119static struct usb_serial_driver * const serial_drivers[] = {
3120 &edgeport_2port_device, &edgeport_4port_device,
3121 &edgeport_8port_device, &epic_device, NULL
3122};
3123
3124module_usb_serial_driver(serial_drivers, id_table_combined);
3125
3126MODULE_AUTHOR(DRIVER_AUTHOR);
3127MODULE_DESCRIPTION(DRIVER_DESC);
3128MODULE_LICENSE("GPL");
3129MODULE_FIRMWARE("edgeport/boot.fw");
3130MODULE_FIRMWARE("edgeport/boot2.fw");
3131MODULE_FIRMWARE("edgeport/down.fw");
3132MODULE_FIRMWARE("edgeport/down2.fw");
1/*
2 * Edgeport USB Serial Converter driver
3 *
4 * Copyright (C) 2000 Inside Out Networks, All rights reserved.
5 * Copyright (C) 2001-2002 Greg Kroah-Hartman <greg@kroah.com>
6 *
7 * This program is free software; you can redistribute it and/or modify
8 * it under the terms of the GNU General Public License as published by
9 * the Free Software Foundation; either version 2 of the License, or
10 * (at your option) any later version.
11 *
12 * Supports the following devices:
13 * Edgeport/4
14 * Edgeport/4t
15 * Edgeport/2
16 * Edgeport/4i
17 * Edgeport/2i
18 * Edgeport/421
19 * Edgeport/21
20 * Rapidport/4
21 * Edgeport/8
22 * Edgeport/2D8
23 * Edgeport/4D8
24 * Edgeport/8i
25 *
26 * For questions or problems with this driver, contact Inside Out
27 * Networks technical support, or Peter Berger <pberger@brimson.com>,
28 * or Al Borchers <alborchers@steinerpoint.com>.
29 *
30 */
31
32#include <linux/kernel.h>
33#include <linux/jiffies.h>
34#include <linux/errno.h>
35#include <linux/slab.h>
36#include <linux/tty.h>
37#include <linux/tty_driver.h>
38#include <linux/tty_flip.h>
39#include <linux/module.h>
40#include <linux/spinlock.h>
41#include <linux/serial.h>
42#include <linux/ioctl.h>
43#include <linux/wait.h>
44#include <linux/firmware.h>
45#include <linux/ihex.h>
46#include <linux/uaccess.h>
47#include <linux/usb.h>
48#include <linux/usb/serial.h>
49#include "io_edgeport.h"
50#include "io_ionsp.h" /* info for the iosp messages */
51#include "io_16654.h" /* 16654 UART defines */
52
53#define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com> and David Iacovelli"
54#define DRIVER_DESC "Edgeport USB Serial Driver"
55
56#define MAX_NAME_LEN 64
57
58#define OPEN_TIMEOUT (5*HZ) /* 5 seconds */
59
60/* receive port state */
61enum RXSTATE {
62 EXPECT_HDR1 = 0, /* Expect header byte 1 */
63 EXPECT_HDR2 = 1, /* Expect header byte 2 */
64 EXPECT_DATA = 2, /* Expect 'RxBytesRemaining' data */
65 EXPECT_HDR3 = 3, /* Expect header byte 3 (for status hdrs only) */
66};
67
68
69/* Transmit Fifo
70 * This Transmit queue is an extension of the edgeport Rx buffer.
71 * The maximum amount of data buffered in both the edgeport
72 * Rx buffer (maxTxCredits) and this buffer will never exceed maxTxCredits.
73 */
74struct TxFifo {
75 unsigned int head; /* index to head pointer (write) */
76 unsigned int tail; /* index to tail pointer (read) */
77 unsigned int count; /* Bytes in queue */
78 unsigned int size; /* Max size of queue (equal to Max number of TxCredits) */
79 unsigned char *fifo; /* allocated Buffer */
80};
81
82/* This structure holds all of the local port information */
83struct edgeport_port {
84 __u16 txCredits; /* our current credits for this port */
85 __u16 maxTxCredits; /* the max size of the port */
86
87 struct TxFifo txfifo; /* transmit fifo -- size will be maxTxCredits */
88 struct urb *write_urb; /* write URB for this port */
89 bool write_in_progress; /* 'true' while a write URB is outstanding */
90 spinlock_t ep_lock;
91
92 __u8 shadowLCR; /* last LCR value received */
93 __u8 shadowMCR; /* last MCR value received */
94 __u8 shadowMSR; /* last MSR value received */
95 __u8 shadowLSR; /* last LSR value received */
96 __u8 shadowXonChar; /* last value set as XON char in Edgeport */
97 __u8 shadowXoffChar; /* last value set as XOFF char in Edgeport */
98 __u8 validDataMask;
99 __u32 baudRate;
100
101 bool open;
102 bool openPending;
103 bool commandPending;
104 bool closePending;
105 bool chaseResponsePending;
106
107 wait_queue_head_t wait_chase; /* for handling sleeping while waiting for chase to finish */
108 wait_queue_head_t wait_open; /* for handling sleeping while waiting for open to finish */
109 wait_queue_head_t wait_command; /* for handling sleeping while waiting for command to finish */
110
111 struct usb_serial_port *port; /* loop back to the owner of this object */
112};
113
114
115/* This structure holds all of the individual device information */
116struct edgeport_serial {
117 char name[MAX_NAME_LEN+2]; /* string name of this device */
118
119 struct edge_manuf_descriptor manuf_descriptor; /* the manufacturer descriptor */
120 struct edge_boot_descriptor boot_descriptor; /* the boot firmware descriptor */
121 struct edgeport_product_info product_info; /* Product Info */
122 struct edge_compatibility_descriptor epic_descriptor; /* Edgeport compatible descriptor */
123 int is_epic; /* flag if EPiC device or not */
124
125 __u8 interrupt_in_endpoint; /* the interrupt endpoint handle */
126 unsigned char *interrupt_in_buffer; /* the buffer we use for the interrupt endpoint */
127 struct urb *interrupt_read_urb; /* our interrupt urb */
128
129 __u8 bulk_in_endpoint; /* the bulk in endpoint handle */
130 unsigned char *bulk_in_buffer; /* the buffer we use for the bulk in endpoint */
131 struct urb *read_urb; /* our bulk read urb */
132 bool read_in_progress;
133 spinlock_t es_lock;
134
135 __u8 bulk_out_endpoint; /* the bulk out endpoint handle */
136
137 __s16 rxBytesAvail; /* the number of bytes that we need to read from this device */
138
139 enum RXSTATE rxState; /* the current state of the bulk receive processor */
140 __u8 rxHeader1; /* receive header byte 1 */
141 __u8 rxHeader2; /* receive header byte 2 */
142 __u8 rxHeader3; /* receive header byte 3 */
143 __u8 rxPort; /* the port that we are currently receiving data for */
144 __u8 rxStatusCode; /* the receive status code */
145 __u8 rxStatusParam; /* the receive status paramater */
146 __s16 rxBytesRemaining; /* the number of port bytes left to read */
147 struct usb_serial *serial; /* loop back to the owner of this object */
148};
149
150/* baud rate information */
151struct divisor_table_entry {
152 __u32 BaudRate;
153 __u16 Divisor;
154};
155
156/*
157 * Define table of divisors for Rev A EdgePort/4 hardware
158 * These assume a 3.6864MHz crystal, the standard /16, and
159 * MCR.7 = 0.
160 */
161
162static const struct divisor_table_entry divisor_table[] = {
163 { 50, 4608},
164 { 75, 3072},
165 { 110, 2095}, /* 2094.545455 => 230450 => .0217 % over */
166 { 134, 1713}, /* 1713.011152 => 230398.5 => .00065% under */
167 { 150, 1536},
168 { 300, 768},
169 { 600, 384},
170 { 1200, 192},
171 { 1800, 128},
172 { 2400, 96},
173 { 4800, 48},
174 { 7200, 32},
175 { 9600, 24},
176 { 14400, 16},
177 { 19200, 12},
178 { 38400, 6},
179 { 57600, 4},
180 { 115200, 2},
181 { 230400, 1},
182};
183
184/* Number of outstanding Command Write Urbs */
185static atomic_t CmdUrbs = ATOMIC_INIT(0);
186
187
188/* local function prototypes */
189
190/* function prototypes for all URB callbacks */
191static void edge_interrupt_callback(struct urb *urb);
192static void edge_bulk_in_callback(struct urb *urb);
193static void edge_bulk_out_data_callback(struct urb *urb);
194static void edge_bulk_out_cmd_callback(struct urb *urb);
195
196/* function prototypes for the usbserial callbacks */
197static int edge_open(struct tty_struct *tty, struct usb_serial_port *port);
198static void edge_close(struct usb_serial_port *port);
199static int edge_write(struct tty_struct *tty, struct usb_serial_port *port,
200 const unsigned char *buf, int count);
201static int edge_write_room(struct tty_struct *tty);
202static int edge_chars_in_buffer(struct tty_struct *tty);
203static void edge_throttle(struct tty_struct *tty);
204static void edge_unthrottle(struct tty_struct *tty);
205static void edge_set_termios(struct tty_struct *tty,
206 struct usb_serial_port *port,
207 struct ktermios *old_termios);
208static int edge_ioctl(struct tty_struct *tty,
209 unsigned int cmd, unsigned long arg);
210static void edge_break(struct tty_struct *tty, int break_state);
211static int edge_tiocmget(struct tty_struct *tty);
212static int edge_tiocmset(struct tty_struct *tty,
213 unsigned int set, unsigned int clear);
214static int edge_startup(struct usb_serial *serial);
215static void edge_disconnect(struct usb_serial *serial);
216static void edge_release(struct usb_serial *serial);
217static int edge_port_probe(struct usb_serial_port *port);
218static int edge_port_remove(struct usb_serial_port *port);
219
220#include "io_tables.h" /* all of the devices that this driver supports */
221
222/* function prototypes for all of our local functions */
223
224static void process_rcvd_data(struct edgeport_serial *edge_serial,
225 unsigned char *buffer, __u16 bufferLength);
226static void process_rcvd_status(struct edgeport_serial *edge_serial,
227 __u8 byte2, __u8 byte3);
228static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data,
229 int length);
230static void handle_new_msr(struct edgeport_port *edge_port, __u8 newMsr);
231static void handle_new_lsr(struct edgeport_port *edge_port, __u8 lsrData,
232 __u8 lsr, __u8 data);
233static int send_iosp_ext_cmd(struct edgeport_port *edge_port, __u8 command,
234 __u8 param);
235static int calc_baud_rate_divisor(struct device *dev, int baud_rate, int *divisor);
236static int send_cmd_write_baud_rate(struct edgeport_port *edge_port,
237 int baudRate);
238static void change_port_settings(struct tty_struct *tty,
239 struct edgeport_port *edge_port,
240 struct ktermios *old_termios);
241static int send_cmd_write_uart_register(struct edgeport_port *edge_port,
242 __u8 regNum, __u8 regValue);
243static int write_cmd_usb(struct edgeport_port *edge_port,
244 unsigned char *buffer, int writeLength);
245static void send_more_port_data(struct edgeport_serial *edge_serial,
246 struct edgeport_port *edge_port);
247
248static int sram_write(struct usb_serial *serial, __u16 extAddr, __u16 addr,
249 __u16 length, const __u8 *data);
250static int rom_read(struct usb_serial *serial, __u16 extAddr, __u16 addr,
251 __u16 length, __u8 *data);
252static int rom_write(struct usb_serial *serial, __u16 extAddr, __u16 addr,
253 __u16 length, const __u8 *data);
254static void get_manufacturing_desc(struct edgeport_serial *edge_serial);
255static void get_boot_desc(struct edgeport_serial *edge_serial);
256static void load_application_firmware(struct edgeport_serial *edge_serial);
257
258static void unicode_to_ascii(char *string, int buflen,
259 __le16 *unicode, int unicode_size);
260
261
262/* ************************************************************************ */
263/* ************************************************************************ */
264/* ************************************************************************ */
265/* ************************************************************************ */
266
267/************************************************************************
268 * *
269 * update_edgeport_E2PROM() Compare current versions of *
270 * Boot ROM and Manufacture *
271 * Descriptors with versions *
272 * embedded in this driver *
273 * *
274 ************************************************************************/
275static void update_edgeport_E2PROM(struct edgeport_serial *edge_serial)
276{
277 struct device *dev = &edge_serial->serial->dev->dev;
278 __u32 BootCurVer;
279 __u32 BootNewVer;
280 __u8 BootMajorVersion;
281 __u8 BootMinorVersion;
282 __u16 BootBuildNumber;
283 __u32 Bootaddr;
284 const struct ihex_binrec *rec;
285 const struct firmware *fw;
286 const char *fw_name;
287 int response;
288
289 switch (edge_serial->product_info.iDownloadFile) {
290 case EDGE_DOWNLOAD_FILE_I930:
291 fw_name = "edgeport/boot.fw";
292 break;
293 case EDGE_DOWNLOAD_FILE_80251:
294 fw_name = "edgeport/boot2.fw";
295 break;
296 default:
297 return;
298 }
299
300 response = request_ihex_firmware(&fw, fw_name,
301 &edge_serial->serial->dev->dev);
302 if (response) {
303 dev_err(dev, "Failed to load image \"%s\" err %d\n",
304 fw_name, response);
305 return;
306 }
307
308 rec = (const struct ihex_binrec *)fw->data;
309 BootMajorVersion = rec->data[0];
310 BootMinorVersion = rec->data[1];
311 BootBuildNumber = (rec->data[2] << 8) | rec->data[3];
312
313 /* Check Boot Image Version */
314 BootCurVer = (edge_serial->boot_descriptor.MajorVersion << 24) +
315 (edge_serial->boot_descriptor.MinorVersion << 16) +
316 le16_to_cpu(edge_serial->boot_descriptor.BuildNumber);
317
318 BootNewVer = (BootMajorVersion << 24) +
319 (BootMinorVersion << 16) +
320 BootBuildNumber;
321
322 dev_dbg(dev, "Current Boot Image version %d.%d.%d\n",
323 edge_serial->boot_descriptor.MajorVersion,
324 edge_serial->boot_descriptor.MinorVersion,
325 le16_to_cpu(edge_serial->boot_descriptor.BuildNumber));
326
327
328 if (BootNewVer > BootCurVer) {
329 dev_dbg(dev, "**Update Boot Image from %d.%d.%d to %d.%d.%d\n",
330 edge_serial->boot_descriptor.MajorVersion,
331 edge_serial->boot_descriptor.MinorVersion,
332 le16_to_cpu(edge_serial->boot_descriptor.BuildNumber),
333 BootMajorVersion, BootMinorVersion, BootBuildNumber);
334
335 dev_dbg(dev, "Downloading new Boot Image\n");
336
337 for (rec = ihex_next_binrec(rec); rec;
338 rec = ihex_next_binrec(rec)) {
339 Bootaddr = be32_to_cpu(rec->addr);
340 response = rom_write(edge_serial->serial,
341 Bootaddr >> 16,
342 Bootaddr & 0xFFFF,
343 be16_to_cpu(rec->len),
344 &rec->data[0]);
345 if (response < 0) {
346 dev_err(&edge_serial->serial->dev->dev,
347 "rom_write failed (%x, %x, %d)\n",
348 Bootaddr >> 16, Bootaddr & 0xFFFF,
349 be16_to_cpu(rec->len));
350 break;
351 }
352 }
353 } else {
354 dev_dbg(dev, "Boot Image -- already up to date\n");
355 }
356 release_firmware(fw);
357}
358
359#if 0
360/************************************************************************
361 *
362 * Get string descriptor from device
363 *
364 ************************************************************************/
365static int get_string_desc(struct usb_device *dev, int Id,
366 struct usb_string_descriptor **pRetDesc)
367{
368 struct usb_string_descriptor StringDesc;
369 struct usb_string_descriptor *pStringDesc;
370
371 dev_dbg(&dev->dev, "%s - USB String ID = %d\n", __func__, Id);
372
373 if (!usb_get_descriptor(dev, USB_DT_STRING, Id, &StringDesc,
374 sizeof(StringDesc)))
375 return 0;
376
377 pStringDesc = kmalloc(StringDesc.bLength, GFP_KERNEL);
378 if (!pStringDesc)
379 return -1;
380
381 if (!usb_get_descriptor(dev, USB_DT_STRING, Id, pStringDesc,
382 StringDesc.bLength)) {
383 kfree(pStringDesc);
384 return -1;
385 }
386
387 *pRetDesc = pStringDesc;
388 return 0;
389}
390#endif
391
392static void dump_product_info(struct edgeport_serial *edge_serial,
393 struct edgeport_product_info *product_info)
394{
395 struct device *dev = &edge_serial->serial->dev->dev;
396
397 /* Dump Product Info structure */
398 dev_dbg(dev, "**Product Information:\n");
399 dev_dbg(dev, " ProductId %x\n", product_info->ProductId);
400 dev_dbg(dev, " NumPorts %d\n", product_info->NumPorts);
401 dev_dbg(dev, " ProdInfoVer %d\n", product_info->ProdInfoVer);
402 dev_dbg(dev, " IsServer %d\n", product_info->IsServer);
403 dev_dbg(dev, " IsRS232 %d\n", product_info->IsRS232);
404 dev_dbg(dev, " IsRS422 %d\n", product_info->IsRS422);
405 dev_dbg(dev, " IsRS485 %d\n", product_info->IsRS485);
406 dev_dbg(dev, " RomSize %d\n", product_info->RomSize);
407 dev_dbg(dev, " RamSize %d\n", product_info->RamSize);
408 dev_dbg(dev, " CpuRev %x\n", product_info->CpuRev);
409 dev_dbg(dev, " BoardRev %x\n", product_info->BoardRev);
410 dev_dbg(dev, " BootMajorVersion %d.%d.%d\n",
411 product_info->BootMajorVersion,
412 product_info->BootMinorVersion,
413 le16_to_cpu(product_info->BootBuildNumber));
414 dev_dbg(dev, " FirmwareMajorVersion %d.%d.%d\n",
415 product_info->FirmwareMajorVersion,
416 product_info->FirmwareMinorVersion,
417 le16_to_cpu(product_info->FirmwareBuildNumber));
418 dev_dbg(dev, " ManufactureDescDate %d/%d/%d\n",
419 product_info->ManufactureDescDate[0],
420 product_info->ManufactureDescDate[1],
421 product_info->ManufactureDescDate[2]+1900);
422 dev_dbg(dev, " iDownloadFile 0x%x\n",
423 product_info->iDownloadFile);
424 dev_dbg(dev, " EpicVer %d\n", product_info->EpicVer);
425}
426
427static void get_product_info(struct edgeport_serial *edge_serial)
428{
429 struct edgeport_product_info *product_info = &edge_serial->product_info;
430
431 memset(product_info, 0, sizeof(struct edgeport_product_info));
432
433 product_info->ProductId = (__u16)(le16_to_cpu(edge_serial->serial->dev->descriptor.idProduct) & ~ION_DEVICE_ID_80251_NETCHIP);
434 product_info->NumPorts = edge_serial->manuf_descriptor.NumPorts;
435 product_info->ProdInfoVer = 0;
436
437 product_info->RomSize = edge_serial->manuf_descriptor.RomSize;
438 product_info->RamSize = edge_serial->manuf_descriptor.RamSize;
439 product_info->CpuRev = edge_serial->manuf_descriptor.CpuRev;
440 product_info->BoardRev = edge_serial->manuf_descriptor.BoardRev;
441
442 product_info->BootMajorVersion =
443 edge_serial->boot_descriptor.MajorVersion;
444 product_info->BootMinorVersion =
445 edge_serial->boot_descriptor.MinorVersion;
446 product_info->BootBuildNumber =
447 edge_serial->boot_descriptor.BuildNumber;
448
449 memcpy(product_info->ManufactureDescDate,
450 edge_serial->manuf_descriptor.DescDate,
451 sizeof(edge_serial->manuf_descriptor.DescDate));
452
453 /* check if this is 2nd generation hardware */
454 if (le16_to_cpu(edge_serial->serial->dev->descriptor.idProduct)
455 & ION_DEVICE_ID_80251_NETCHIP)
456 product_info->iDownloadFile = EDGE_DOWNLOAD_FILE_80251;
457 else
458 product_info->iDownloadFile = EDGE_DOWNLOAD_FILE_I930;
459
460 /* Determine Product type and set appropriate flags */
461 switch (DEVICE_ID_FROM_USB_PRODUCT_ID(product_info->ProductId)) {
462 case ION_DEVICE_ID_EDGEPORT_COMPATIBLE:
463 case ION_DEVICE_ID_EDGEPORT_4T:
464 case ION_DEVICE_ID_EDGEPORT_4:
465 case ION_DEVICE_ID_EDGEPORT_2:
466 case ION_DEVICE_ID_EDGEPORT_8_DUAL_CPU:
467 case ION_DEVICE_ID_EDGEPORT_8:
468 case ION_DEVICE_ID_EDGEPORT_421:
469 case ION_DEVICE_ID_EDGEPORT_21:
470 case ION_DEVICE_ID_EDGEPORT_2_DIN:
471 case ION_DEVICE_ID_EDGEPORT_4_DIN:
472 case ION_DEVICE_ID_EDGEPORT_16_DUAL_CPU:
473 product_info->IsRS232 = 1;
474 break;
475
476 case ION_DEVICE_ID_EDGEPORT_2I: /* Edgeport/2 RS422/RS485 */
477 product_info->IsRS422 = 1;
478 product_info->IsRS485 = 1;
479 break;
480
481 case ION_DEVICE_ID_EDGEPORT_8I: /* Edgeport/4 RS422 */
482 case ION_DEVICE_ID_EDGEPORT_4I: /* Edgeport/4 RS422 */
483 product_info->IsRS422 = 1;
484 break;
485 }
486
487 dump_product_info(edge_serial, product_info);
488}
489
490static int get_epic_descriptor(struct edgeport_serial *ep)
491{
492 int result;
493 struct usb_serial *serial = ep->serial;
494 struct edgeport_product_info *product_info = &ep->product_info;
495 struct edge_compatibility_descriptor *epic = &ep->epic_descriptor;
496 struct edge_compatibility_bits *bits;
497 struct device *dev = &serial->dev->dev;
498
499 ep->is_epic = 0;
500 result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
501 USB_REQUEST_ION_GET_EPIC_DESC,
502 0xC0, 0x00, 0x00,
503 &ep->epic_descriptor,
504 sizeof(struct edge_compatibility_descriptor),
505 300);
506
507 if (result > 0) {
508 ep->is_epic = 1;
509 memset(product_info, 0, sizeof(struct edgeport_product_info));
510
511 product_info->NumPorts = epic->NumPorts;
512 product_info->ProdInfoVer = 0;
513 product_info->FirmwareMajorVersion = epic->MajorVersion;
514 product_info->FirmwareMinorVersion = epic->MinorVersion;
515 product_info->FirmwareBuildNumber = epic->BuildNumber;
516 product_info->iDownloadFile = epic->iDownloadFile;
517 product_info->EpicVer = epic->EpicVer;
518 product_info->Epic = epic->Supports;
519 product_info->ProductId = ION_DEVICE_ID_EDGEPORT_COMPATIBLE;
520 dump_product_info(ep, product_info);
521
522 bits = &ep->epic_descriptor.Supports;
523 dev_dbg(dev, "**EPIC descriptor:\n");
524 dev_dbg(dev, " VendEnableSuspend: %s\n", bits->VendEnableSuspend ? "TRUE": "FALSE");
525 dev_dbg(dev, " IOSPOpen : %s\n", bits->IOSPOpen ? "TRUE": "FALSE");
526 dev_dbg(dev, " IOSPClose : %s\n", bits->IOSPClose ? "TRUE": "FALSE");
527 dev_dbg(dev, " IOSPChase : %s\n", bits->IOSPChase ? "TRUE": "FALSE");
528 dev_dbg(dev, " IOSPSetRxFlow : %s\n", bits->IOSPSetRxFlow ? "TRUE": "FALSE");
529 dev_dbg(dev, " IOSPSetTxFlow : %s\n", bits->IOSPSetTxFlow ? "TRUE": "FALSE");
530 dev_dbg(dev, " IOSPSetXChar : %s\n", bits->IOSPSetXChar ? "TRUE": "FALSE");
531 dev_dbg(dev, " IOSPRxCheck : %s\n", bits->IOSPRxCheck ? "TRUE": "FALSE");
532 dev_dbg(dev, " IOSPSetClrBreak : %s\n", bits->IOSPSetClrBreak ? "TRUE": "FALSE");
533 dev_dbg(dev, " IOSPWriteMCR : %s\n", bits->IOSPWriteMCR ? "TRUE": "FALSE");
534 dev_dbg(dev, " IOSPWriteLCR : %s\n", bits->IOSPWriteLCR ? "TRUE": "FALSE");
535 dev_dbg(dev, " IOSPSetBaudRate : %s\n", bits->IOSPSetBaudRate ? "TRUE": "FALSE");
536 dev_dbg(dev, " TrueEdgeport : %s\n", bits->TrueEdgeport ? "TRUE": "FALSE");
537 }
538
539 return result;
540}
541
542
543/************************************************************************/
544/************************************************************************/
545/* U S B C A L L B A C K F U N C T I O N S */
546/* U S B C A L L B A C K F U N C T I O N S */
547/************************************************************************/
548/************************************************************************/
549
550/*****************************************************************************
551 * edge_interrupt_callback
552 * this is the callback function for when we have received data on the
553 * interrupt endpoint.
554 *****************************************************************************/
555static void edge_interrupt_callback(struct urb *urb)
556{
557 struct edgeport_serial *edge_serial = urb->context;
558 struct device *dev;
559 struct edgeport_port *edge_port;
560 struct usb_serial_port *port;
561 unsigned char *data = urb->transfer_buffer;
562 int length = urb->actual_length;
563 int bytes_avail;
564 int position;
565 int txCredits;
566 int portNumber;
567 int result;
568 int status = urb->status;
569
570 switch (status) {
571 case 0:
572 /* success */
573 break;
574 case -ECONNRESET:
575 case -ENOENT:
576 case -ESHUTDOWN:
577 /* this urb is terminated, clean up */
578 dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", __func__, status);
579 return;
580 default:
581 dev_dbg(&urb->dev->dev, "%s - nonzero urb status received: %d\n", __func__, status);
582 goto exit;
583 }
584
585 dev = &edge_serial->serial->dev->dev;
586
587 /* process this interrupt-read even if there are no ports open */
588 if (length) {
589 usb_serial_debug_data(dev, __func__, length, data);
590
591 if (length > 1) {
592 bytes_avail = data[0] | (data[1] << 8);
593 if (bytes_avail) {
594 spin_lock(&edge_serial->es_lock);
595 edge_serial->rxBytesAvail += bytes_avail;
596 dev_dbg(dev,
597 "%s - bytes_avail=%d, rxBytesAvail=%d, read_in_progress=%d\n",
598 __func__, bytes_avail,
599 edge_serial->rxBytesAvail,
600 edge_serial->read_in_progress);
601
602 if (edge_serial->rxBytesAvail > 0 &&
603 !edge_serial->read_in_progress) {
604 dev_dbg(dev, "%s - posting a read\n", __func__);
605 edge_serial->read_in_progress = true;
606
607 /* we have pending bytes on the
608 bulk in pipe, send a request */
609 result = usb_submit_urb(edge_serial->read_urb, GFP_ATOMIC);
610 if (result) {
611 dev_err(dev,
612 "%s - usb_submit_urb(read bulk) failed with result = %d\n",
613 __func__, result);
614 edge_serial->read_in_progress = false;
615 }
616 }
617 spin_unlock(&edge_serial->es_lock);
618 }
619 }
620 /* grab the txcredits for the ports if available */
621 position = 2;
622 portNumber = 0;
623 while ((position < length) &&
624 (portNumber < edge_serial->serial->num_ports)) {
625 txCredits = data[position] | (data[position+1] << 8);
626 if (txCredits) {
627 port = edge_serial->serial->port[portNumber];
628 edge_port = usb_get_serial_port_data(port);
629 if (edge_port->open) {
630 spin_lock(&edge_port->ep_lock);
631 edge_port->txCredits += txCredits;
632 spin_unlock(&edge_port->ep_lock);
633 dev_dbg(dev, "%s - txcredits for port%d = %d\n",
634 __func__, portNumber,
635 edge_port->txCredits);
636
637 /* tell the tty driver that something
638 has changed */
639 tty_port_tty_wakeup(&edge_port->port->port);
640 /* Since we have more credit, check
641 if more data can be sent */
642 send_more_port_data(edge_serial,
643 edge_port);
644 }
645 }
646 position += 2;
647 ++portNumber;
648 }
649 }
650
651exit:
652 result = usb_submit_urb(urb, GFP_ATOMIC);
653 if (result)
654 dev_err(&urb->dev->dev,
655 "%s - Error %d submitting control urb\n",
656 __func__, result);
657}
658
659
660/*****************************************************************************
661 * edge_bulk_in_callback
662 * this is the callback function for when we have received data on the
663 * bulk in endpoint.
664 *****************************************************************************/
665static void edge_bulk_in_callback(struct urb *urb)
666{
667 struct edgeport_serial *edge_serial = urb->context;
668 struct device *dev;
669 unsigned char *data = urb->transfer_buffer;
670 int retval;
671 __u16 raw_data_length;
672 int status = urb->status;
673
674 if (status) {
675 dev_dbg(&urb->dev->dev, "%s - nonzero read bulk status received: %d\n",
676 __func__, status);
677 edge_serial->read_in_progress = false;
678 return;
679 }
680
681 if (urb->actual_length == 0) {
682 dev_dbg(&urb->dev->dev, "%s - read bulk callback with no data\n", __func__);
683 edge_serial->read_in_progress = false;
684 return;
685 }
686
687 dev = &edge_serial->serial->dev->dev;
688 raw_data_length = urb->actual_length;
689
690 usb_serial_debug_data(dev, __func__, raw_data_length, data);
691
692 spin_lock(&edge_serial->es_lock);
693
694 /* decrement our rxBytes available by the number that we just got */
695 edge_serial->rxBytesAvail -= raw_data_length;
696
697 dev_dbg(dev, "%s - Received = %d, rxBytesAvail %d\n", __func__,
698 raw_data_length, edge_serial->rxBytesAvail);
699
700 process_rcvd_data(edge_serial, data, urb->actual_length);
701
702 /* check to see if there's any more data for us to read */
703 if (edge_serial->rxBytesAvail > 0) {
704 dev_dbg(dev, "%s - posting a read\n", __func__);
705 retval = usb_submit_urb(edge_serial->read_urb, GFP_ATOMIC);
706 if (retval) {
707 dev_err(dev,
708 "%s - usb_submit_urb(read bulk) failed, retval = %d\n",
709 __func__, retval);
710 edge_serial->read_in_progress = false;
711 }
712 } else {
713 edge_serial->read_in_progress = false;
714 }
715
716 spin_unlock(&edge_serial->es_lock);
717}
718
719
720/*****************************************************************************
721 * edge_bulk_out_data_callback
722 * this is the callback function for when we have finished sending
723 * serial data on the bulk out endpoint.
724 *****************************************************************************/
725static void edge_bulk_out_data_callback(struct urb *urb)
726{
727 struct edgeport_port *edge_port = urb->context;
728 int status = urb->status;
729
730 if (status) {
731 dev_dbg(&urb->dev->dev,
732 "%s - nonzero write bulk status received: %d\n",
733 __func__, status);
734 }
735
736 if (edge_port->open)
737 tty_port_tty_wakeup(&edge_port->port->port);
738
739 /* Release the Write URB */
740 edge_port->write_in_progress = false;
741
742 /* Check if more data needs to be sent */
743 send_more_port_data((struct edgeport_serial *)
744 (usb_get_serial_data(edge_port->port->serial)), edge_port);
745}
746
747
748/*****************************************************************************
749 * BulkOutCmdCallback
750 * this is the callback function for when we have finished sending a
751 * command on the bulk out endpoint.
752 *****************************************************************************/
753static void edge_bulk_out_cmd_callback(struct urb *urb)
754{
755 struct edgeport_port *edge_port = urb->context;
756 int status = urb->status;
757
758 atomic_dec(&CmdUrbs);
759 dev_dbg(&urb->dev->dev, "%s - FREE URB %p (outstanding %d)\n",
760 __func__, urb, atomic_read(&CmdUrbs));
761
762
763 /* clean up the transfer buffer */
764 kfree(urb->transfer_buffer);
765
766 /* Free the command urb */
767 usb_free_urb(urb);
768
769 if (status) {
770 dev_dbg(&urb->dev->dev,
771 "%s - nonzero write bulk status received: %d\n",
772 __func__, status);
773 return;
774 }
775
776 /* tell the tty driver that something has changed */
777 if (edge_port->open)
778 tty_port_tty_wakeup(&edge_port->port->port);
779
780 /* we have completed the command */
781 edge_port->commandPending = false;
782 wake_up(&edge_port->wait_command);
783}
784
785
786/*****************************************************************************
787 * Driver tty interface functions
788 *****************************************************************************/
789
790/*****************************************************************************
791 * SerialOpen
792 * this function is called by the tty driver when a port is opened
793 * If successful, we return 0
794 * Otherwise we return a negative error number.
795 *****************************************************************************/
796static int edge_open(struct tty_struct *tty, struct usb_serial_port *port)
797{
798 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
799 struct device *dev = &port->dev;
800 struct usb_serial *serial;
801 struct edgeport_serial *edge_serial;
802 int response;
803
804 if (edge_port == NULL)
805 return -ENODEV;
806
807 /* see if we've set up our endpoint info yet (can't set it up
808 in edge_startup as the structures were not set up at that time.) */
809 serial = port->serial;
810 edge_serial = usb_get_serial_data(serial);
811 if (edge_serial == NULL)
812 return -ENODEV;
813 if (edge_serial->interrupt_in_buffer == NULL) {
814 struct usb_serial_port *port0 = serial->port[0];
815
816 /* not set up yet, so do it now */
817 edge_serial->interrupt_in_buffer =
818 port0->interrupt_in_buffer;
819 edge_serial->interrupt_in_endpoint =
820 port0->interrupt_in_endpointAddress;
821 edge_serial->interrupt_read_urb = port0->interrupt_in_urb;
822 edge_serial->bulk_in_buffer = port0->bulk_in_buffer;
823 edge_serial->bulk_in_endpoint =
824 port0->bulk_in_endpointAddress;
825 edge_serial->read_urb = port0->read_urb;
826 edge_serial->bulk_out_endpoint =
827 port0->bulk_out_endpointAddress;
828
829 /* set up our interrupt urb */
830 usb_fill_int_urb(edge_serial->interrupt_read_urb,
831 serial->dev,
832 usb_rcvintpipe(serial->dev,
833 port0->interrupt_in_endpointAddress),
834 port0->interrupt_in_buffer,
835 edge_serial->interrupt_read_urb->transfer_buffer_length,
836 edge_interrupt_callback, edge_serial,
837 edge_serial->interrupt_read_urb->interval);
838
839 /* set up our bulk in urb */
840 usb_fill_bulk_urb(edge_serial->read_urb, serial->dev,
841 usb_rcvbulkpipe(serial->dev,
842 port0->bulk_in_endpointAddress),
843 port0->bulk_in_buffer,
844 edge_serial->read_urb->transfer_buffer_length,
845 edge_bulk_in_callback, edge_serial);
846 edge_serial->read_in_progress = false;
847
848 /* start interrupt read for this edgeport
849 * this interrupt will continue as long
850 * as the edgeport is connected */
851 response = usb_submit_urb(edge_serial->interrupt_read_urb,
852 GFP_KERNEL);
853 if (response) {
854 dev_err(dev, "%s - Error %d submitting control urb\n",
855 __func__, response);
856 }
857 }
858
859 /* initialize our wait queues */
860 init_waitqueue_head(&edge_port->wait_open);
861 init_waitqueue_head(&edge_port->wait_chase);
862 init_waitqueue_head(&edge_port->wait_command);
863
864 /* initialize our port settings */
865 edge_port->txCredits = 0; /* Can't send any data yet */
866 /* Must always set this bit to enable ints! */
867 edge_port->shadowMCR = MCR_MASTER_IE;
868 edge_port->chaseResponsePending = false;
869
870 /* send a open port command */
871 edge_port->openPending = true;
872 edge_port->open = false;
873 response = send_iosp_ext_cmd(edge_port, IOSP_CMD_OPEN_PORT, 0);
874
875 if (response < 0) {
876 dev_err(dev, "%s - error sending open port command\n", __func__);
877 edge_port->openPending = false;
878 return -ENODEV;
879 }
880
881 /* now wait for the port to be completely opened */
882 wait_event_timeout(edge_port->wait_open, !edge_port->openPending,
883 OPEN_TIMEOUT);
884
885 if (!edge_port->open) {
886 /* open timed out */
887 dev_dbg(dev, "%s - open timedout\n", __func__);
888 edge_port->openPending = false;
889 return -ENODEV;
890 }
891
892 /* create the txfifo */
893 edge_port->txfifo.head = 0;
894 edge_port->txfifo.tail = 0;
895 edge_port->txfifo.count = 0;
896 edge_port->txfifo.size = edge_port->maxTxCredits;
897 edge_port->txfifo.fifo = kmalloc(edge_port->maxTxCredits, GFP_KERNEL);
898
899 if (!edge_port->txfifo.fifo) {
900 edge_close(port);
901 return -ENOMEM;
902 }
903
904 /* Allocate a URB for the write */
905 edge_port->write_urb = usb_alloc_urb(0, GFP_KERNEL);
906 edge_port->write_in_progress = false;
907
908 if (!edge_port->write_urb) {
909 edge_close(port);
910 return -ENOMEM;
911 }
912
913 dev_dbg(dev, "%s - Initialize TX fifo to %d bytes\n",
914 __func__, edge_port->maxTxCredits);
915
916 return 0;
917}
918
919
920/************************************************************************
921 *
922 * block_until_chase_response
923 *
924 * This function will block the close until one of the following:
925 * 1. Response to our Chase comes from Edgeport
926 * 2. A timeout of 10 seconds without activity has expired
927 * (1K of Edgeport data @ 2400 baud ==> 4 sec to empty)
928 *
929 ************************************************************************/
930static void block_until_chase_response(struct edgeport_port *edge_port)
931{
932 struct device *dev = &edge_port->port->dev;
933 DEFINE_WAIT(wait);
934 __u16 lastCredits;
935 int timeout = 1*HZ;
936 int loop = 10;
937
938 while (1) {
939 /* Save Last credits */
940 lastCredits = edge_port->txCredits;
941
942 /* Did we get our Chase response */
943 if (!edge_port->chaseResponsePending) {
944 dev_dbg(dev, "%s - Got Chase Response\n", __func__);
945
946 /* did we get all of our credit back? */
947 if (edge_port->txCredits == edge_port->maxTxCredits) {
948 dev_dbg(dev, "%s - Got all credits\n", __func__);
949 return;
950 }
951 }
952
953 /* Block the thread for a while */
954 prepare_to_wait(&edge_port->wait_chase, &wait,
955 TASK_UNINTERRUPTIBLE);
956 schedule_timeout(timeout);
957 finish_wait(&edge_port->wait_chase, &wait);
958
959 if (lastCredits == edge_port->txCredits) {
960 /* No activity.. count down. */
961 loop--;
962 if (loop == 0) {
963 edge_port->chaseResponsePending = false;
964 dev_dbg(dev, "%s - Chase TIMEOUT\n", __func__);
965 return;
966 }
967 } else {
968 /* Reset timeout value back to 10 seconds */
969 dev_dbg(dev, "%s - Last %d, Current %d\n", __func__,
970 lastCredits, edge_port->txCredits);
971 loop = 10;
972 }
973 }
974}
975
976
977/************************************************************************
978 *
979 * block_until_tx_empty
980 *
981 * This function will block the close until one of the following:
982 * 1. TX count are 0
983 * 2. The edgeport has stopped
984 * 3. A timeout of 3 seconds without activity has expired
985 *
986 ************************************************************************/
987static void block_until_tx_empty(struct edgeport_port *edge_port)
988{
989 struct device *dev = &edge_port->port->dev;
990 DEFINE_WAIT(wait);
991 struct TxFifo *fifo = &edge_port->txfifo;
992 __u32 lastCount;
993 int timeout = HZ/10;
994 int loop = 30;
995
996 while (1) {
997 /* Save Last count */
998 lastCount = fifo->count;
999
1000 /* Is the Edgeport Buffer empty? */
1001 if (lastCount == 0) {
1002 dev_dbg(dev, "%s - TX Buffer Empty\n", __func__);
1003 return;
1004 }
1005
1006 /* Block the thread for a while */
1007 prepare_to_wait(&edge_port->wait_chase, &wait,
1008 TASK_UNINTERRUPTIBLE);
1009 schedule_timeout(timeout);
1010 finish_wait(&edge_port->wait_chase, &wait);
1011
1012 dev_dbg(dev, "%s wait\n", __func__);
1013
1014 if (lastCount == fifo->count) {
1015 /* No activity.. count down. */
1016 loop--;
1017 if (loop == 0) {
1018 dev_dbg(dev, "%s - TIMEOUT\n", __func__);
1019 return;
1020 }
1021 } else {
1022 /* Reset timeout value back to seconds */
1023 loop = 30;
1024 }
1025 }
1026}
1027
1028
1029/*****************************************************************************
1030 * edge_close
1031 * this function is called by the tty driver when a port is closed
1032 *****************************************************************************/
1033static void edge_close(struct usb_serial_port *port)
1034{
1035 struct edgeport_serial *edge_serial;
1036 struct edgeport_port *edge_port;
1037 int status;
1038
1039 edge_serial = usb_get_serial_data(port->serial);
1040 edge_port = usb_get_serial_port_data(port);
1041 if (edge_serial == NULL || edge_port == NULL)
1042 return;
1043
1044 /* block until tx is empty */
1045 block_until_tx_empty(edge_port);
1046
1047 edge_port->closePending = true;
1048
1049 if ((!edge_serial->is_epic) ||
1050 ((edge_serial->is_epic) &&
1051 (edge_serial->epic_descriptor.Supports.IOSPChase))) {
1052 /* flush and chase */
1053 edge_port->chaseResponsePending = true;
1054
1055 dev_dbg(&port->dev, "%s - Sending IOSP_CMD_CHASE_PORT\n", __func__);
1056 status = send_iosp_ext_cmd(edge_port, IOSP_CMD_CHASE_PORT, 0);
1057 if (status == 0)
1058 /* block until chase finished */
1059 block_until_chase_response(edge_port);
1060 else
1061 edge_port->chaseResponsePending = false;
1062 }
1063
1064 if ((!edge_serial->is_epic) ||
1065 ((edge_serial->is_epic) &&
1066 (edge_serial->epic_descriptor.Supports.IOSPClose))) {
1067 /* close the port */
1068 dev_dbg(&port->dev, "%s - Sending IOSP_CMD_CLOSE_PORT\n", __func__);
1069 send_iosp_ext_cmd(edge_port, IOSP_CMD_CLOSE_PORT, 0);
1070 }
1071
1072 /* port->close = true; */
1073 edge_port->closePending = false;
1074 edge_port->open = false;
1075 edge_port->openPending = false;
1076
1077 usb_kill_urb(edge_port->write_urb);
1078
1079 if (edge_port->write_urb) {
1080 /* if this urb had a transfer buffer already
1081 (old transfer) free it */
1082 kfree(edge_port->write_urb->transfer_buffer);
1083 usb_free_urb(edge_port->write_urb);
1084 edge_port->write_urb = NULL;
1085 }
1086 kfree(edge_port->txfifo.fifo);
1087 edge_port->txfifo.fifo = NULL;
1088}
1089
1090/*****************************************************************************
1091 * SerialWrite
1092 * this function is called by the tty driver when data should be written
1093 * to the port.
1094 * If successful, we return the number of bytes written, otherwise we
1095 * return a negative error number.
1096 *****************************************************************************/
1097static int edge_write(struct tty_struct *tty, struct usb_serial_port *port,
1098 const unsigned char *data, int count)
1099{
1100 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1101 struct TxFifo *fifo;
1102 int copySize;
1103 int bytesleft;
1104 int firsthalf;
1105 int secondhalf;
1106 unsigned long flags;
1107
1108 if (edge_port == NULL)
1109 return -ENODEV;
1110
1111 /* get a pointer to the Tx fifo */
1112 fifo = &edge_port->txfifo;
1113
1114 spin_lock_irqsave(&edge_port->ep_lock, flags);
1115
1116 /* calculate number of bytes to put in fifo */
1117 copySize = min((unsigned int)count,
1118 (edge_port->txCredits - fifo->count));
1119
1120 dev_dbg(&port->dev, "%s of %d byte(s) Fifo room %d -- will copy %d bytes\n",
1121 __func__, count, edge_port->txCredits - fifo->count, copySize);
1122
1123 /* catch writes of 0 bytes which the tty driver likes to give us,
1124 and when txCredits is empty */
1125 if (copySize == 0) {
1126 dev_dbg(&port->dev, "%s - copySize = Zero\n", __func__);
1127 goto finish_write;
1128 }
1129
1130 /* queue the data
1131 * since we can never overflow the buffer we do not have to check for a
1132 * full condition
1133 *
1134 * the copy is done is two parts -- first fill to the end of the buffer
1135 * then copy the reset from the start of the buffer
1136 */
1137 bytesleft = fifo->size - fifo->head;
1138 firsthalf = min(bytesleft, copySize);
1139 dev_dbg(&port->dev, "%s - copy %d bytes of %d into fifo \n", __func__,
1140 firsthalf, bytesleft);
1141
1142 /* now copy our data */
1143 memcpy(&fifo->fifo[fifo->head], data, firsthalf);
1144 usb_serial_debug_data(&port->dev, __func__, firsthalf, &fifo->fifo[fifo->head]);
1145
1146 /* update the index and size */
1147 fifo->head += firsthalf;
1148 fifo->count += firsthalf;
1149
1150 /* wrap the index */
1151 if (fifo->head == fifo->size)
1152 fifo->head = 0;
1153
1154 secondhalf = copySize-firsthalf;
1155
1156 if (secondhalf) {
1157 dev_dbg(&port->dev, "%s - copy rest of data %d\n", __func__, secondhalf);
1158 memcpy(&fifo->fifo[fifo->head], &data[firsthalf], secondhalf);
1159 usb_serial_debug_data(&port->dev, __func__, secondhalf, &fifo->fifo[fifo->head]);
1160 /* update the index and size */
1161 fifo->count += secondhalf;
1162 fifo->head += secondhalf;
1163 /* No need to check for wrap since we can not get to end of
1164 * the fifo in this part
1165 */
1166 }
1167
1168finish_write:
1169 spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1170
1171 send_more_port_data((struct edgeport_serial *)
1172 usb_get_serial_data(port->serial), edge_port);
1173
1174 dev_dbg(&port->dev, "%s wrote %d byte(s) TxCredits %d, Fifo %d\n",
1175 __func__, copySize, edge_port->txCredits, fifo->count);
1176
1177 return copySize;
1178}
1179
1180
1181/************************************************************************
1182 *
1183 * send_more_port_data()
1184 *
1185 * This routine attempts to write additional UART transmit data
1186 * to a port over the USB bulk pipe. It is called (1) when new
1187 * data has been written to a port's TxBuffer from higher layers
1188 * (2) when the peripheral sends us additional TxCredits indicating
1189 * that it can accept more Tx data for a given port; and (3) when
1190 * a bulk write completes successfully and we want to see if we
1191 * can transmit more.
1192 *
1193 ************************************************************************/
1194static void send_more_port_data(struct edgeport_serial *edge_serial,
1195 struct edgeport_port *edge_port)
1196{
1197 struct TxFifo *fifo = &edge_port->txfifo;
1198 struct device *dev = &edge_port->port->dev;
1199 struct urb *urb;
1200 unsigned char *buffer;
1201 int status;
1202 int count;
1203 int bytesleft;
1204 int firsthalf;
1205 int secondhalf;
1206 unsigned long flags;
1207
1208 spin_lock_irqsave(&edge_port->ep_lock, flags);
1209
1210 if (edge_port->write_in_progress ||
1211 !edge_port->open ||
1212 (fifo->count == 0)) {
1213 dev_dbg(dev, "%s EXIT - fifo %d, PendingWrite = %d\n",
1214 __func__, fifo->count, edge_port->write_in_progress);
1215 goto exit_send;
1216 }
1217
1218 /* since the amount of data in the fifo will always fit into the
1219 * edgeport buffer we do not need to check the write length
1220 *
1221 * Do we have enough credits for this port to make it worthwhile
1222 * to bother queueing a write. If it's too small, say a few bytes,
1223 * it's better to wait for more credits so we can do a larger write.
1224 */
1225 if (edge_port->txCredits < EDGE_FW_GET_TX_CREDITS_SEND_THRESHOLD(edge_port->maxTxCredits, EDGE_FW_BULK_MAX_PACKET_SIZE)) {
1226 dev_dbg(dev, "%s Not enough credit - fifo %d TxCredit %d\n",
1227 __func__, fifo->count, edge_port->txCredits);
1228 goto exit_send;
1229 }
1230
1231 /* lock this write */
1232 edge_port->write_in_progress = true;
1233
1234 /* get a pointer to the write_urb */
1235 urb = edge_port->write_urb;
1236
1237 /* make sure transfer buffer is freed */
1238 kfree(urb->transfer_buffer);
1239 urb->transfer_buffer = NULL;
1240
1241 /* build the data header for the buffer and port that we are about
1242 to send out */
1243 count = fifo->count;
1244 buffer = kmalloc(count+2, GFP_ATOMIC);
1245 if (!buffer) {
1246 edge_port->write_in_progress = false;
1247 goto exit_send;
1248 }
1249 buffer[0] = IOSP_BUILD_DATA_HDR1(edge_port->port->port_number, count);
1250 buffer[1] = IOSP_BUILD_DATA_HDR2(edge_port->port->port_number, count);
1251
1252 /* now copy our data */
1253 bytesleft = fifo->size - fifo->tail;
1254 firsthalf = min(bytesleft, count);
1255 memcpy(&buffer[2], &fifo->fifo[fifo->tail], firsthalf);
1256 fifo->tail += firsthalf;
1257 fifo->count -= firsthalf;
1258 if (fifo->tail == fifo->size)
1259 fifo->tail = 0;
1260
1261 secondhalf = count-firsthalf;
1262 if (secondhalf) {
1263 memcpy(&buffer[2+firsthalf], &fifo->fifo[fifo->tail],
1264 secondhalf);
1265 fifo->tail += secondhalf;
1266 fifo->count -= secondhalf;
1267 }
1268
1269 if (count)
1270 usb_serial_debug_data(&edge_port->port->dev, __func__, count, &buffer[2]);
1271
1272 /* fill up the urb with all of our data and submit it */
1273 usb_fill_bulk_urb(urb, edge_serial->serial->dev,
1274 usb_sndbulkpipe(edge_serial->serial->dev,
1275 edge_serial->bulk_out_endpoint),
1276 buffer, count+2,
1277 edge_bulk_out_data_callback, edge_port);
1278
1279 /* decrement the number of credits we have by the number we just sent */
1280 edge_port->txCredits -= count;
1281 edge_port->port->icount.tx += count;
1282
1283 status = usb_submit_urb(urb, GFP_ATOMIC);
1284 if (status) {
1285 /* something went wrong */
1286 dev_err_console(edge_port->port,
1287 "%s - usb_submit_urb(write bulk) failed, status = %d, data lost\n",
1288 __func__, status);
1289 edge_port->write_in_progress = false;
1290
1291 /* revert the credits as something bad happened. */
1292 edge_port->txCredits += count;
1293 edge_port->port->icount.tx -= count;
1294 }
1295 dev_dbg(dev, "%s wrote %d byte(s) TxCredit %d, Fifo %d\n",
1296 __func__, count, edge_port->txCredits, fifo->count);
1297
1298exit_send:
1299 spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1300}
1301
1302
1303/*****************************************************************************
1304 * edge_write_room
1305 * this function is called by the tty driver when it wants to know how
1306 * many bytes of data we can accept for a specific port. If successful,
1307 * we return the amount of room that we have for this port (the txCredits)
1308 * otherwise we return a negative error number.
1309 *****************************************************************************/
1310static int edge_write_room(struct tty_struct *tty)
1311{
1312 struct usb_serial_port *port = tty->driver_data;
1313 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1314 int room;
1315 unsigned long flags;
1316
1317 if (edge_port == NULL)
1318 return 0;
1319 if (edge_port->closePending)
1320 return 0;
1321
1322 if (!edge_port->open) {
1323 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1324 return 0;
1325 }
1326
1327 /* total of both buffers is still txCredit */
1328 spin_lock_irqsave(&edge_port->ep_lock, flags);
1329 room = edge_port->txCredits - edge_port->txfifo.count;
1330 spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1331
1332 dev_dbg(&port->dev, "%s - returns %d\n", __func__, room);
1333 return room;
1334}
1335
1336
1337/*****************************************************************************
1338 * edge_chars_in_buffer
1339 * this function is called by the tty driver when it wants to know how
1340 * many bytes of data we currently have outstanding in the port (data that
1341 * has been written, but hasn't made it out the port yet)
1342 * If successful, we return the number of bytes left to be written in the
1343 * system,
1344 * Otherwise we return a negative error number.
1345 *****************************************************************************/
1346static int edge_chars_in_buffer(struct tty_struct *tty)
1347{
1348 struct usb_serial_port *port = tty->driver_data;
1349 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1350 int num_chars;
1351 unsigned long flags;
1352
1353 if (edge_port == NULL)
1354 return 0;
1355 if (edge_port->closePending)
1356 return 0;
1357
1358 if (!edge_port->open) {
1359 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1360 return 0;
1361 }
1362
1363 spin_lock_irqsave(&edge_port->ep_lock, flags);
1364 num_chars = edge_port->maxTxCredits - edge_port->txCredits +
1365 edge_port->txfifo.count;
1366 spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1367 if (num_chars) {
1368 dev_dbg(&port->dev, "%s - returns %d\n", __func__, num_chars);
1369 }
1370
1371 return num_chars;
1372}
1373
1374
1375/*****************************************************************************
1376 * SerialThrottle
1377 * this function is called by the tty driver when it wants to stop the data
1378 * being read from the port.
1379 *****************************************************************************/
1380static void edge_throttle(struct tty_struct *tty)
1381{
1382 struct usb_serial_port *port = tty->driver_data;
1383 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1384 int status;
1385
1386 if (edge_port == NULL)
1387 return;
1388
1389 if (!edge_port->open) {
1390 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1391 return;
1392 }
1393
1394 /* if we are implementing XON/XOFF, send the stop character */
1395 if (I_IXOFF(tty)) {
1396 unsigned char stop_char = STOP_CHAR(tty);
1397 status = edge_write(tty, port, &stop_char, 1);
1398 if (status <= 0)
1399 return;
1400 }
1401
1402 /* if we are implementing RTS/CTS, toggle that line */
1403 if (tty->termios.c_cflag & CRTSCTS) {
1404 edge_port->shadowMCR &= ~MCR_RTS;
1405 status = send_cmd_write_uart_register(edge_port, MCR,
1406 edge_port->shadowMCR);
1407 if (status != 0)
1408 return;
1409 }
1410}
1411
1412
1413/*****************************************************************************
1414 * edge_unthrottle
1415 * this function is called by the tty driver when it wants to resume the
1416 * data being read from the port (called after SerialThrottle is called)
1417 *****************************************************************************/
1418static void edge_unthrottle(struct tty_struct *tty)
1419{
1420 struct usb_serial_port *port = tty->driver_data;
1421 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1422 int status;
1423
1424 if (edge_port == NULL)
1425 return;
1426
1427 if (!edge_port->open) {
1428 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1429 return;
1430 }
1431
1432 /* if we are implementing XON/XOFF, send the start character */
1433 if (I_IXOFF(tty)) {
1434 unsigned char start_char = START_CHAR(tty);
1435 status = edge_write(tty, port, &start_char, 1);
1436 if (status <= 0)
1437 return;
1438 }
1439 /* if we are implementing RTS/CTS, toggle that line */
1440 if (tty->termios.c_cflag & CRTSCTS) {
1441 edge_port->shadowMCR |= MCR_RTS;
1442 send_cmd_write_uart_register(edge_port, MCR,
1443 edge_port->shadowMCR);
1444 }
1445}
1446
1447
1448/*****************************************************************************
1449 * SerialSetTermios
1450 * this function is called by the tty driver when it wants to change
1451 * the termios structure
1452 *****************************************************************************/
1453static void edge_set_termios(struct tty_struct *tty,
1454 struct usb_serial_port *port, struct ktermios *old_termios)
1455{
1456 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1457 unsigned int cflag;
1458
1459 cflag = tty->termios.c_cflag;
1460 dev_dbg(&port->dev, "%s - clfag %08x iflag %08x\n", __func__, tty->termios.c_cflag, tty->termios.c_iflag);
1461 dev_dbg(&port->dev, "%s - old clfag %08x old iflag %08x\n", __func__, old_termios->c_cflag, old_termios->c_iflag);
1462
1463 if (edge_port == NULL)
1464 return;
1465
1466 if (!edge_port->open) {
1467 dev_dbg(&port->dev, "%s - port not opened\n", __func__);
1468 return;
1469 }
1470
1471 /* change the port settings to the new ones specified */
1472 change_port_settings(tty, edge_port, old_termios);
1473}
1474
1475
1476/*****************************************************************************
1477 * get_lsr_info - get line status register info
1478 *
1479 * Purpose: Let user call ioctl() to get info when the UART physically
1480 * is emptied. On bus types like RS485, the transmitter must
1481 * release the bus after transmitting. This must be done when
1482 * the transmit shift register is empty, not be done when the
1483 * transmit holding register is empty. This functionality
1484 * allows an RS485 driver to be written in user space.
1485 *****************************************************************************/
1486static int get_lsr_info(struct edgeport_port *edge_port,
1487 unsigned int __user *value)
1488{
1489 unsigned int result = 0;
1490 unsigned long flags;
1491
1492 spin_lock_irqsave(&edge_port->ep_lock, flags);
1493 if (edge_port->maxTxCredits == edge_port->txCredits &&
1494 edge_port->txfifo.count == 0) {
1495 dev_dbg(&edge_port->port->dev, "%s -- Empty\n", __func__);
1496 result = TIOCSER_TEMT;
1497 }
1498 spin_unlock_irqrestore(&edge_port->ep_lock, flags);
1499
1500 if (copy_to_user(value, &result, sizeof(int)))
1501 return -EFAULT;
1502 return 0;
1503}
1504
1505static int edge_tiocmset(struct tty_struct *tty,
1506 unsigned int set, unsigned int clear)
1507{
1508 struct usb_serial_port *port = tty->driver_data;
1509 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1510 unsigned int mcr;
1511
1512 mcr = edge_port->shadowMCR;
1513 if (set & TIOCM_RTS)
1514 mcr |= MCR_RTS;
1515 if (set & TIOCM_DTR)
1516 mcr |= MCR_DTR;
1517 if (set & TIOCM_LOOP)
1518 mcr |= MCR_LOOPBACK;
1519
1520 if (clear & TIOCM_RTS)
1521 mcr &= ~MCR_RTS;
1522 if (clear & TIOCM_DTR)
1523 mcr &= ~MCR_DTR;
1524 if (clear & TIOCM_LOOP)
1525 mcr &= ~MCR_LOOPBACK;
1526
1527 edge_port->shadowMCR = mcr;
1528
1529 send_cmd_write_uart_register(edge_port, MCR, edge_port->shadowMCR);
1530
1531 return 0;
1532}
1533
1534static int edge_tiocmget(struct tty_struct *tty)
1535{
1536 struct usb_serial_port *port = tty->driver_data;
1537 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1538 unsigned int result = 0;
1539 unsigned int msr;
1540 unsigned int mcr;
1541
1542 msr = edge_port->shadowMSR;
1543 mcr = edge_port->shadowMCR;
1544 result = ((mcr & MCR_DTR) ? TIOCM_DTR: 0) /* 0x002 */
1545 | ((mcr & MCR_RTS) ? TIOCM_RTS: 0) /* 0x004 */
1546 | ((msr & EDGEPORT_MSR_CTS) ? TIOCM_CTS: 0) /* 0x020 */
1547 | ((msr & EDGEPORT_MSR_CD) ? TIOCM_CAR: 0) /* 0x040 */
1548 | ((msr & EDGEPORT_MSR_RI) ? TIOCM_RI: 0) /* 0x080 */
1549 | ((msr & EDGEPORT_MSR_DSR) ? TIOCM_DSR: 0); /* 0x100 */
1550
1551 return result;
1552}
1553
1554static int get_serial_info(struct edgeport_port *edge_port,
1555 struct serial_struct __user *retinfo)
1556{
1557 struct serial_struct tmp;
1558
1559 if (!retinfo)
1560 return -EFAULT;
1561
1562 memset(&tmp, 0, sizeof(tmp));
1563
1564 tmp.type = PORT_16550A;
1565 tmp.line = edge_port->port->minor;
1566 tmp.port = edge_port->port->port_number;
1567 tmp.irq = 0;
1568 tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ;
1569 tmp.xmit_fifo_size = edge_port->maxTxCredits;
1570 tmp.baud_base = 9600;
1571 tmp.close_delay = 5*HZ;
1572 tmp.closing_wait = 30*HZ;
1573
1574 if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
1575 return -EFAULT;
1576 return 0;
1577}
1578
1579
1580/*****************************************************************************
1581 * SerialIoctl
1582 * this function handles any ioctl calls to the driver
1583 *****************************************************************************/
1584static int edge_ioctl(struct tty_struct *tty,
1585 unsigned int cmd, unsigned long arg)
1586{
1587 struct usb_serial_port *port = tty->driver_data;
1588 DEFINE_WAIT(wait);
1589 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1590
1591 switch (cmd) {
1592 case TIOCSERGETLSR:
1593 dev_dbg(&port->dev, "%s TIOCSERGETLSR\n", __func__);
1594 return get_lsr_info(edge_port, (unsigned int __user *) arg);
1595
1596 case TIOCGSERIAL:
1597 dev_dbg(&port->dev, "%s TIOCGSERIAL\n", __func__);
1598 return get_serial_info(edge_port, (struct serial_struct __user *) arg);
1599 }
1600 return -ENOIOCTLCMD;
1601}
1602
1603
1604/*****************************************************************************
1605 * SerialBreak
1606 * this function sends a break to the port
1607 *****************************************************************************/
1608static void edge_break(struct tty_struct *tty, int break_state)
1609{
1610 struct usb_serial_port *port = tty->driver_data;
1611 struct edgeport_port *edge_port = usb_get_serial_port_data(port);
1612 struct edgeport_serial *edge_serial = usb_get_serial_data(port->serial);
1613 int status;
1614
1615 if ((!edge_serial->is_epic) ||
1616 ((edge_serial->is_epic) &&
1617 (edge_serial->epic_descriptor.Supports.IOSPChase))) {
1618 /* flush and chase */
1619 edge_port->chaseResponsePending = true;
1620
1621 dev_dbg(&port->dev, "%s - Sending IOSP_CMD_CHASE_PORT\n", __func__);
1622 status = send_iosp_ext_cmd(edge_port, IOSP_CMD_CHASE_PORT, 0);
1623 if (status == 0) {
1624 /* block until chase finished */
1625 block_until_chase_response(edge_port);
1626 } else {
1627 edge_port->chaseResponsePending = false;
1628 }
1629 }
1630
1631 if ((!edge_serial->is_epic) ||
1632 ((edge_serial->is_epic) &&
1633 (edge_serial->epic_descriptor.Supports.IOSPSetClrBreak))) {
1634 if (break_state == -1) {
1635 dev_dbg(&port->dev, "%s - Sending IOSP_CMD_SET_BREAK\n", __func__);
1636 status = send_iosp_ext_cmd(edge_port,
1637 IOSP_CMD_SET_BREAK, 0);
1638 } else {
1639 dev_dbg(&port->dev, "%s - Sending IOSP_CMD_CLEAR_BREAK\n", __func__);
1640 status = send_iosp_ext_cmd(edge_port,
1641 IOSP_CMD_CLEAR_BREAK, 0);
1642 }
1643 if (status)
1644 dev_dbg(&port->dev, "%s - error sending break set/clear command.\n",
1645 __func__);
1646 }
1647}
1648
1649
1650/*****************************************************************************
1651 * process_rcvd_data
1652 * this function handles the data received on the bulk in pipe.
1653 *****************************************************************************/
1654static void process_rcvd_data(struct edgeport_serial *edge_serial,
1655 unsigned char *buffer, __u16 bufferLength)
1656{
1657 struct device *dev = &edge_serial->serial->dev->dev;
1658 struct usb_serial_port *port;
1659 struct edgeport_port *edge_port;
1660 __u16 lastBufferLength;
1661 __u16 rxLen;
1662
1663 lastBufferLength = bufferLength + 1;
1664
1665 while (bufferLength > 0) {
1666 /* failsafe incase we get a message that we don't understand */
1667 if (lastBufferLength == bufferLength) {
1668 dev_dbg(dev, "%s - stuck in loop, exiting it.\n", __func__);
1669 break;
1670 }
1671 lastBufferLength = bufferLength;
1672
1673 switch (edge_serial->rxState) {
1674 case EXPECT_HDR1:
1675 edge_serial->rxHeader1 = *buffer;
1676 ++buffer;
1677 --bufferLength;
1678
1679 if (bufferLength == 0) {
1680 edge_serial->rxState = EXPECT_HDR2;
1681 break;
1682 }
1683 /* otherwise, drop on through */
1684 case EXPECT_HDR2:
1685 edge_serial->rxHeader2 = *buffer;
1686 ++buffer;
1687 --bufferLength;
1688
1689 dev_dbg(dev, "%s - Hdr1=%02X Hdr2=%02X\n", __func__,
1690 edge_serial->rxHeader1, edge_serial->rxHeader2);
1691 /* Process depending on whether this header is
1692 * data or status */
1693
1694 if (IS_CMD_STAT_HDR(edge_serial->rxHeader1)) {
1695 /* Decode this status header and go to
1696 * EXPECT_HDR1 (if we can process the status
1697 * with only 2 bytes), or go to EXPECT_HDR3 to
1698 * get the third byte. */
1699 edge_serial->rxPort =
1700 IOSP_GET_HDR_PORT(edge_serial->rxHeader1);
1701 edge_serial->rxStatusCode =
1702 IOSP_GET_STATUS_CODE(
1703 edge_serial->rxHeader1);
1704
1705 if (!IOSP_STATUS_IS_2BYTE(
1706 edge_serial->rxStatusCode)) {
1707 /* This status needs additional bytes.
1708 * Save what we have and then wait for
1709 * more data.
1710 */
1711 edge_serial->rxStatusParam
1712 = edge_serial->rxHeader2;
1713 edge_serial->rxState = EXPECT_HDR3;
1714 break;
1715 }
1716 /* We have all the header bytes, process the
1717 status now */
1718 process_rcvd_status(edge_serial,
1719 edge_serial->rxHeader2, 0);
1720 edge_serial->rxState = EXPECT_HDR1;
1721 break;
1722 } else {
1723 edge_serial->rxPort =
1724 IOSP_GET_HDR_PORT(edge_serial->rxHeader1);
1725 edge_serial->rxBytesRemaining =
1726 IOSP_GET_HDR_DATA_LEN(
1727 edge_serial->rxHeader1,
1728 edge_serial->rxHeader2);
1729 dev_dbg(dev, "%s - Data for Port %u Len %u\n",
1730 __func__,
1731 edge_serial->rxPort,
1732 edge_serial->rxBytesRemaining);
1733
1734 /* ASSERT(DevExt->RxPort < DevExt->NumPorts);
1735 * ASSERT(DevExt->RxBytesRemaining <
1736 * IOSP_MAX_DATA_LENGTH);
1737 */
1738
1739 if (bufferLength == 0) {
1740 edge_serial->rxState = EXPECT_DATA;
1741 break;
1742 }
1743 /* Else, drop through */
1744 }
1745 case EXPECT_DATA: /* Expect data */
1746 if (bufferLength < edge_serial->rxBytesRemaining) {
1747 rxLen = bufferLength;
1748 /* Expect data to start next buffer */
1749 edge_serial->rxState = EXPECT_DATA;
1750 } else {
1751 /* BufLen >= RxBytesRemaining */
1752 rxLen = edge_serial->rxBytesRemaining;
1753 /* Start another header next time */
1754 edge_serial->rxState = EXPECT_HDR1;
1755 }
1756
1757 bufferLength -= rxLen;
1758 edge_serial->rxBytesRemaining -= rxLen;
1759
1760 /* spit this data back into the tty driver if this
1761 port is open */
1762 if (rxLen) {
1763 port = edge_serial->serial->port[
1764 edge_serial->rxPort];
1765 edge_port = usb_get_serial_port_data(port);
1766 if (edge_port->open) {
1767 dev_dbg(dev, "%s - Sending %d bytes to TTY for port %d\n",
1768 __func__, rxLen,
1769 edge_serial->rxPort);
1770 edge_tty_recv(edge_port->port, buffer,
1771 rxLen);
1772 edge_port->port->icount.rx += rxLen;
1773 }
1774 buffer += rxLen;
1775 }
1776 break;
1777
1778 case EXPECT_HDR3: /* Expect 3rd byte of status header */
1779 edge_serial->rxHeader3 = *buffer;
1780 ++buffer;
1781 --bufferLength;
1782
1783 /* We have all the header bytes, process the
1784 status now */
1785 process_rcvd_status(edge_serial,
1786 edge_serial->rxStatusParam,
1787 edge_serial->rxHeader3);
1788 edge_serial->rxState = EXPECT_HDR1;
1789 break;
1790 }
1791 }
1792}
1793
1794
1795/*****************************************************************************
1796 * process_rcvd_status
1797 * this function handles the any status messages received on the
1798 * bulk in pipe.
1799 *****************************************************************************/
1800static void process_rcvd_status(struct edgeport_serial *edge_serial,
1801 __u8 byte2, __u8 byte3)
1802{
1803 struct usb_serial_port *port;
1804 struct edgeport_port *edge_port;
1805 struct tty_struct *tty;
1806 struct device *dev;
1807 __u8 code = edge_serial->rxStatusCode;
1808
1809 /* switch the port pointer to the one being currently talked about */
1810 port = edge_serial->serial->port[edge_serial->rxPort];
1811 edge_port = usb_get_serial_port_data(port);
1812 if (edge_port == NULL) {
1813 dev_err(&edge_serial->serial->dev->dev,
1814 "%s - edge_port == NULL for port %d\n",
1815 __func__, edge_serial->rxPort);
1816 return;
1817 }
1818 dev = &port->dev;
1819
1820 if (code == IOSP_EXT_STATUS) {
1821 switch (byte2) {
1822 case IOSP_EXT_STATUS_CHASE_RSP:
1823 /* we want to do EXT status regardless of port
1824 * open/closed */
1825 dev_dbg(dev, "%s - Port %u EXT CHASE_RSP Data = %02x\n",
1826 __func__, edge_serial->rxPort, byte3);
1827 /* Currently, the only EXT_STATUS is Chase, so process
1828 * here instead of one more call to one more subroutine
1829 * If/when more EXT_STATUS, there'll be more work to do
1830 * Also, we currently clear flag and close the port
1831 * regardless of content of above's Byte3.
1832 * We could choose to do something else when Byte3 says
1833 * Timeout on Chase from Edgeport, like wait longer in
1834 * block_until_chase_response, but for now we don't.
1835 */
1836 edge_port->chaseResponsePending = false;
1837 wake_up(&edge_port->wait_chase);
1838 return;
1839
1840 case IOSP_EXT_STATUS_RX_CHECK_RSP:
1841 dev_dbg(dev, "%s ========== Port %u CHECK_RSP Sequence = %02x =============\n",
1842 __func__, edge_serial->rxPort, byte3);
1843 /* Port->RxCheckRsp = true; */
1844 return;
1845 }
1846 }
1847
1848 if (code == IOSP_STATUS_OPEN_RSP) {
1849 edge_port->txCredits = GET_TX_BUFFER_SIZE(byte3);
1850 edge_port->maxTxCredits = edge_port->txCredits;
1851 dev_dbg(dev, "%s - Port %u Open Response Initial MSR = %02x TxBufferSize = %d\n",
1852 __func__, edge_serial->rxPort, byte2, edge_port->txCredits);
1853 handle_new_msr(edge_port, byte2);
1854
1855 /* send the current line settings to the port so we are
1856 in sync with any further termios calls */
1857 tty = tty_port_tty_get(&edge_port->port->port);
1858 if (tty) {
1859 change_port_settings(tty,
1860 edge_port, &tty->termios);
1861 tty_kref_put(tty);
1862 }
1863
1864 /* we have completed the open */
1865 edge_port->openPending = false;
1866 edge_port->open = true;
1867 wake_up(&edge_port->wait_open);
1868 return;
1869 }
1870
1871 /* If port is closed, silently discard all rcvd status. We can
1872 * have cases where buffered status is received AFTER the close
1873 * port command is sent to the Edgeport.
1874 */
1875 if (!edge_port->open || edge_port->closePending)
1876 return;
1877
1878 switch (code) {
1879 /* Not currently sent by Edgeport */
1880 case IOSP_STATUS_LSR:
1881 dev_dbg(dev, "%s - Port %u LSR Status = %02x\n",
1882 __func__, edge_serial->rxPort, byte2);
1883 handle_new_lsr(edge_port, false, byte2, 0);
1884 break;
1885
1886 case IOSP_STATUS_LSR_DATA:
1887 dev_dbg(dev, "%s - Port %u LSR Status = %02x, Data = %02x\n",
1888 __func__, edge_serial->rxPort, byte2, byte3);
1889 /* byte2 is LSR Register */
1890 /* byte3 is broken data byte */
1891 handle_new_lsr(edge_port, true, byte2, byte3);
1892 break;
1893 /*
1894 * case IOSP_EXT_4_STATUS:
1895 * dev_dbg(dev, "%s - Port %u LSR Status = %02x Data = %02x\n",
1896 * __func__, edge_serial->rxPort, byte2, byte3);
1897 * break;
1898 */
1899 case IOSP_STATUS_MSR:
1900 dev_dbg(dev, "%s - Port %u MSR Status = %02x\n",
1901 __func__, edge_serial->rxPort, byte2);
1902 /*
1903 * Process this new modem status and generate appropriate
1904 * events, etc, based on the new status. This routine
1905 * also saves the MSR in Port->ShadowMsr.
1906 */
1907 handle_new_msr(edge_port, byte2);
1908 break;
1909
1910 default:
1911 dev_dbg(dev, "%s - Unrecognized IOSP status code %u\n", __func__, code);
1912 break;
1913 }
1914}
1915
1916
1917/*****************************************************************************
1918 * edge_tty_recv
1919 * this function passes data on to the tty flip buffer
1920 *****************************************************************************/
1921static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data,
1922 int length)
1923{
1924 int cnt;
1925
1926 cnt = tty_insert_flip_string(&port->port, data, length);
1927 if (cnt < length) {
1928 dev_err(&port->dev, "%s - dropping data, %d bytes lost\n",
1929 __func__, length - cnt);
1930 }
1931 data += cnt;
1932 length -= cnt;
1933
1934 tty_flip_buffer_push(&port->port);
1935}
1936
1937
1938/*****************************************************************************
1939 * handle_new_msr
1940 * this function handles any change to the msr register for a port.
1941 *****************************************************************************/
1942static void handle_new_msr(struct edgeport_port *edge_port, __u8 newMsr)
1943{
1944 struct async_icount *icount;
1945
1946 if (newMsr & (EDGEPORT_MSR_DELTA_CTS | EDGEPORT_MSR_DELTA_DSR |
1947 EDGEPORT_MSR_DELTA_RI | EDGEPORT_MSR_DELTA_CD)) {
1948 icount = &edge_port->port->icount;
1949
1950 /* update input line counters */
1951 if (newMsr & EDGEPORT_MSR_DELTA_CTS)
1952 icount->cts++;
1953 if (newMsr & EDGEPORT_MSR_DELTA_DSR)
1954 icount->dsr++;
1955 if (newMsr & EDGEPORT_MSR_DELTA_CD)
1956 icount->dcd++;
1957 if (newMsr & EDGEPORT_MSR_DELTA_RI)
1958 icount->rng++;
1959 wake_up_interruptible(&edge_port->port->port.delta_msr_wait);
1960 }
1961
1962 /* Save the new modem status */
1963 edge_port->shadowMSR = newMsr & 0xf0;
1964}
1965
1966
1967/*****************************************************************************
1968 * handle_new_lsr
1969 * this function handles any change to the lsr register for a port.
1970 *****************************************************************************/
1971static void handle_new_lsr(struct edgeport_port *edge_port, __u8 lsrData,
1972 __u8 lsr, __u8 data)
1973{
1974 __u8 newLsr = (__u8) (lsr & (__u8)
1975 (LSR_OVER_ERR | LSR_PAR_ERR | LSR_FRM_ERR | LSR_BREAK));
1976 struct async_icount *icount;
1977
1978 edge_port->shadowLSR = lsr;
1979
1980 if (newLsr & LSR_BREAK) {
1981 /*
1982 * Parity and Framing errors only count if they
1983 * occur exclusive of a break being
1984 * received.
1985 */
1986 newLsr &= (__u8)(LSR_OVER_ERR | LSR_BREAK);
1987 }
1988
1989 /* Place LSR data byte into Rx buffer */
1990 if (lsrData)
1991 edge_tty_recv(edge_port->port, &data, 1);
1992
1993 /* update input line counters */
1994 icount = &edge_port->port->icount;
1995 if (newLsr & LSR_BREAK)
1996 icount->brk++;
1997 if (newLsr & LSR_OVER_ERR)
1998 icount->overrun++;
1999 if (newLsr & LSR_PAR_ERR)
2000 icount->parity++;
2001 if (newLsr & LSR_FRM_ERR)
2002 icount->frame++;
2003}
2004
2005
2006/****************************************************************************
2007 * sram_write
2008 * writes a number of bytes to the Edgeport device's sram starting at the
2009 * given address.
2010 * If successful returns the number of bytes written, otherwise it returns
2011 * a negative error number of the problem.
2012 ****************************************************************************/
2013static int sram_write(struct usb_serial *serial, __u16 extAddr, __u16 addr,
2014 __u16 length, const __u8 *data)
2015{
2016 int result;
2017 __u16 current_length;
2018 unsigned char *transfer_buffer;
2019
2020 dev_dbg(&serial->dev->dev, "%s - %x, %x, %d\n", __func__, extAddr, addr, length);
2021
2022 transfer_buffer = kmalloc(64, GFP_KERNEL);
2023 if (!transfer_buffer)
2024 return -ENOMEM;
2025
2026 /* need to split these writes up into 64 byte chunks */
2027 result = 0;
2028 while (length > 0) {
2029 if (length > 64)
2030 current_length = 64;
2031 else
2032 current_length = length;
2033
2034/* dev_dbg(&serial->dev->dev, "%s - writing %x, %x, %d\n", __func__, extAddr, addr, current_length); */
2035 memcpy(transfer_buffer, data, current_length);
2036 result = usb_control_msg(serial->dev,
2037 usb_sndctrlpipe(serial->dev, 0),
2038 USB_REQUEST_ION_WRITE_RAM,
2039 0x40, addr, extAddr, transfer_buffer,
2040 current_length, 300);
2041 if (result < 0)
2042 break;
2043 length -= current_length;
2044 addr += current_length;
2045 data += current_length;
2046 }
2047
2048 kfree(transfer_buffer);
2049 return result;
2050}
2051
2052
2053/****************************************************************************
2054 * rom_write
2055 * writes a number of bytes to the Edgeport device's ROM starting at the
2056 * given address.
2057 * If successful returns the number of bytes written, otherwise it returns
2058 * a negative error number of the problem.
2059 ****************************************************************************/
2060static int rom_write(struct usb_serial *serial, __u16 extAddr, __u16 addr,
2061 __u16 length, const __u8 *data)
2062{
2063 int result;
2064 __u16 current_length;
2065 unsigned char *transfer_buffer;
2066
2067 transfer_buffer = kmalloc(64, GFP_KERNEL);
2068 if (!transfer_buffer)
2069 return -ENOMEM;
2070
2071 /* need to split these writes up into 64 byte chunks */
2072 result = 0;
2073 while (length > 0) {
2074 if (length > 64)
2075 current_length = 64;
2076 else
2077 current_length = length;
2078 memcpy(transfer_buffer, data, current_length);
2079 result = usb_control_msg(serial->dev,
2080 usb_sndctrlpipe(serial->dev, 0),
2081 USB_REQUEST_ION_WRITE_ROM, 0x40,
2082 addr, extAddr,
2083 transfer_buffer, current_length, 300);
2084 if (result < 0)
2085 break;
2086 length -= current_length;
2087 addr += current_length;
2088 data += current_length;
2089 }
2090
2091 kfree(transfer_buffer);
2092 return result;
2093}
2094
2095
2096/****************************************************************************
2097 * rom_read
2098 * reads a number of bytes from the Edgeport device starting at the given
2099 * address.
2100 * If successful returns the number of bytes read, otherwise it returns
2101 * a negative error number of the problem.
2102 ****************************************************************************/
2103static int rom_read(struct usb_serial *serial, __u16 extAddr,
2104 __u16 addr, __u16 length, __u8 *data)
2105{
2106 int result;
2107 __u16 current_length;
2108 unsigned char *transfer_buffer;
2109
2110 transfer_buffer = kmalloc(64, GFP_KERNEL);
2111 if (!transfer_buffer)
2112 return -ENOMEM;
2113
2114 /* need to split these reads up into 64 byte chunks */
2115 result = 0;
2116 while (length > 0) {
2117 if (length > 64)
2118 current_length = 64;
2119 else
2120 current_length = length;
2121 result = usb_control_msg(serial->dev,
2122 usb_rcvctrlpipe(serial->dev, 0),
2123 USB_REQUEST_ION_READ_ROM,
2124 0xC0, addr, extAddr, transfer_buffer,
2125 current_length, 300);
2126 if (result < 0)
2127 break;
2128 memcpy(data, transfer_buffer, current_length);
2129 length -= current_length;
2130 addr += current_length;
2131 data += current_length;
2132 }
2133
2134 kfree(transfer_buffer);
2135 return result;
2136}
2137
2138
2139/****************************************************************************
2140 * send_iosp_ext_cmd
2141 * Is used to send a IOSP message to the Edgeport device
2142 ****************************************************************************/
2143static int send_iosp_ext_cmd(struct edgeport_port *edge_port,
2144 __u8 command, __u8 param)
2145{
2146 unsigned char *buffer;
2147 unsigned char *currentCommand;
2148 int length = 0;
2149 int status = 0;
2150
2151 buffer = kmalloc(10, GFP_ATOMIC);
2152 if (!buffer)
2153 return -ENOMEM;
2154
2155 currentCommand = buffer;
2156
2157 MAKE_CMD_EXT_CMD(¤tCommand, &length, edge_port->port->port_number,
2158 command, param);
2159
2160 status = write_cmd_usb(edge_port, buffer, length);
2161 if (status) {
2162 /* something bad happened, let's free up the memory */
2163 kfree(buffer);
2164 }
2165
2166 return status;
2167}
2168
2169
2170/*****************************************************************************
2171 * write_cmd_usb
2172 * this function writes the given buffer out to the bulk write endpoint.
2173 *****************************************************************************/
2174static int write_cmd_usb(struct edgeport_port *edge_port,
2175 unsigned char *buffer, int length)
2176{
2177 struct edgeport_serial *edge_serial =
2178 usb_get_serial_data(edge_port->port->serial);
2179 struct device *dev = &edge_port->port->dev;
2180 int status = 0;
2181 struct urb *urb;
2182
2183 usb_serial_debug_data(dev, __func__, length, buffer);
2184
2185 /* Allocate our next urb */
2186 urb = usb_alloc_urb(0, GFP_ATOMIC);
2187 if (!urb)
2188 return -ENOMEM;
2189
2190 atomic_inc(&CmdUrbs);
2191 dev_dbg(dev, "%s - ALLOCATE URB %p (outstanding %d)\n",
2192 __func__, urb, atomic_read(&CmdUrbs));
2193
2194 usb_fill_bulk_urb(urb, edge_serial->serial->dev,
2195 usb_sndbulkpipe(edge_serial->serial->dev,
2196 edge_serial->bulk_out_endpoint),
2197 buffer, length, edge_bulk_out_cmd_callback, edge_port);
2198
2199 edge_port->commandPending = true;
2200 status = usb_submit_urb(urb, GFP_ATOMIC);
2201
2202 if (status) {
2203 /* something went wrong */
2204 dev_err(dev, "%s - usb_submit_urb(write command) failed, status = %d\n",
2205 __func__, status);
2206 usb_kill_urb(urb);
2207 usb_free_urb(urb);
2208 atomic_dec(&CmdUrbs);
2209 return status;
2210 }
2211
2212#if 0
2213 wait_event(&edge_port->wait_command, !edge_port->commandPending);
2214
2215 if (edge_port->commandPending) {
2216 /* command timed out */
2217 dev_dbg(dev, "%s - command timed out\n", __func__);
2218 status = -EINVAL;
2219 }
2220#endif
2221 return status;
2222}
2223
2224
2225/*****************************************************************************
2226 * send_cmd_write_baud_rate
2227 * this function sends the proper command to change the baud rate of the
2228 * specified port.
2229 *****************************************************************************/
2230static int send_cmd_write_baud_rate(struct edgeport_port *edge_port,
2231 int baudRate)
2232{
2233 struct edgeport_serial *edge_serial =
2234 usb_get_serial_data(edge_port->port->serial);
2235 struct device *dev = &edge_port->port->dev;
2236 unsigned char *cmdBuffer;
2237 unsigned char *currCmd;
2238 int cmdLen = 0;
2239 int divisor;
2240 int status;
2241 u32 number = edge_port->port->port_number;
2242
2243 if (edge_serial->is_epic &&
2244 !edge_serial->epic_descriptor.Supports.IOSPSetBaudRate) {
2245 dev_dbg(dev, "SendCmdWriteBaudRate - NOT Setting baud rate for port, baud = %d\n",
2246 baudRate);
2247 return 0;
2248 }
2249
2250 dev_dbg(dev, "%s - baud = %d\n", __func__, baudRate);
2251
2252 status = calc_baud_rate_divisor(dev, baudRate, &divisor);
2253 if (status) {
2254 dev_err(dev, "%s - bad baud rate\n", __func__);
2255 return status;
2256 }
2257
2258 /* Alloc memory for the string of commands. */
2259 cmdBuffer = kmalloc(0x100, GFP_ATOMIC);
2260 if (!cmdBuffer)
2261 return -ENOMEM;
2262
2263 currCmd = cmdBuffer;
2264
2265 /* Enable access to divisor latch */
2266 MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, LCR, LCR_DL_ENABLE);
2267
2268 /* Write the divisor itself */
2269 MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, DLL, LOW8(divisor));
2270 MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, DLM, HIGH8(divisor));
2271
2272 /* Restore original value to disable access to divisor latch */
2273 MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, number, LCR,
2274 edge_port->shadowLCR);
2275
2276 status = write_cmd_usb(edge_port, cmdBuffer, cmdLen);
2277 if (status) {
2278 /* something bad happened, let's free up the memory */
2279 kfree(cmdBuffer);
2280 }
2281
2282 return status;
2283}
2284
2285
2286/*****************************************************************************
2287 * calc_baud_rate_divisor
2288 * this function calculates the proper baud rate divisor for the specified
2289 * baud rate.
2290 *****************************************************************************/
2291static int calc_baud_rate_divisor(struct device *dev, int baudrate, int *divisor)
2292{
2293 int i;
2294 __u16 custom;
2295
2296 for (i = 0; i < ARRAY_SIZE(divisor_table); i++) {
2297 if (divisor_table[i].BaudRate == baudrate) {
2298 *divisor = divisor_table[i].Divisor;
2299 return 0;
2300 }
2301 }
2302
2303 /* We have tried all of the standard baud rates
2304 * lets try to calculate the divisor for this baud rate
2305 * Make sure the baud rate is reasonable */
2306 if (baudrate > 50 && baudrate < 230400) {
2307 /* get divisor */
2308 custom = (__u16)((230400L + baudrate/2) / baudrate);
2309
2310 *divisor = custom;
2311
2312 dev_dbg(dev, "%s - Baud %d = %d\n", __func__, baudrate, custom);
2313 return 0;
2314 }
2315
2316 return -1;
2317}
2318
2319
2320/*****************************************************************************
2321 * send_cmd_write_uart_register
2322 * this function builds up a uart register message and sends to the device.
2323 *****************************************************************************/
2324static int send_cmd_write_uart_register(struct edgeport_port *edge_port,
2325 __u8 regNum, __u8 regValue)
2326{
2327 struct edgeport_serial *edge_serial =
2328 usb_get_serial_data(edge_port->port->serial);
2329 struct device *dev = &edge_port->port->dev;
2330 unsigned char *cmdBuffer;
2331 unsigned char *currCmd;
2332 unsigned long cmdLen = 0;
2333 int status;
2334
2335 dev_dbg(dev, "%s - write to %s register 0x%02x\n",
2336 (regNum == MCR) ? "MCR" : "LCR", __func__, regValue);
2337
2338 if (edge_serial->is_epic &&
2339 !edge_serial->epic_descriptor.Supports.IOSPWriteMCR &&
2340 regNum == MCR) {
2341 dev_dbg(dev, "SendCmdWriteUartReg - Not writing to MCR Register\n");
2342 return 0;
2343 }
2344
2345 if (edge_serial->is_epic &&
2346 !edge_serial->epic_descriptor.Supports.IOSPWriteLCR &&
2347 regNum == LCR) {
2348 dev_dbg(dev, "SendCmdWriteUartReg - Not writing to LCR Register\n");
2349 return 0;
2350 }
2351
2352 /* Alloc memory for the string of commands. */
2353 cmdBuffer = kmalloc(0x10, GFP_ATOMIC);
2354 if (cmdBuffer == NULL)
2355 return -ENOMEM;
2356
2357 currCmd = cmdBuffer;
2358
2359 /* Build a cmd in the buffer to write the given register */
2360 MAKE_CMD_WRITE_REG(&currCmd, &cmdLen, edge_port->port->port_number,
2361 regNum, regValue);
2362
2363 status = write_cmd_usb(edge_port, cmdBuffer, cmdLen);
2364 if (status) {
2365 /* something bad happened, let's free up the memory */
2366 kfree(cmdBuffer);
2367 }
2368
2369 return status;
2370}
2371
2372
2373/*****************************************************************************
2374 * change_port_settings
2375 * This routine is called to set the UART on the device to match the
2376 * specified new settings.
2377 *****************************************************************************/
2378
2379static void change_port_settings(struct tty_struct *tty,
2380 struct edgeport_port *edge_port, struct ktermios *old_termios)
2381{
2382 struct device *dev = &edge_port->port->dev;
2383 struct edgeport_serial *edge_serial =
2384 usb_get_serial_data(edge_port->port->serial);
2385 int baud;
2386 unsigned cflag;
2387 __u8 mask = 0xff;
2388 __u8 lData;
2389 __u8 lParity;
2390 __u8 lStop;
2391 __u8 rxFlow;
2392 __u8 txFlow;
2393 int status;
2394
2395 if (!edge_port->open &&
2396 !edge_port->openPending) {
2397 dev_dbg(dev, "%s - port not opened\n", __func__);
2398 return;
2399 }
2400
2401 cflag = tty->termios.c_cflag;
2402
2403 switch (cflag & CSIZE) {
2404 case CS5:
2405 lData = LCR_BITS_5; mask = 0x1f;
2406 dev_dbg(dev, "%s - data bits = 5\n", __func__);
2407 break;
2408 case CS6:
2409 lData = LCR_BITS_6; mask = 0x3f;
2410 dev_dbg(dev, "%s - data bits = 6\n", __func__);
2411 break;
2412 case CS7:
2413 lData = LCR_BITS_7; mask = 0x7f;
2414 dev_dbg(dev, "%s - data bits = 7\n", __func__);
2415 break;
2416 default:
2417 case CS8:
2418 lData = LCR_BITS_8;
2419 dev_dbg(dev, "%s - data bits = 8\n", __func__);
2420 break;
2421 }
2422
2423 lParity = LCR_PAR_NONE;
2424 if (cflag & PARENB) {
2425 if (cflag & CMSPAR) {
2426 if (cflag & PARODD) {
2427 lParity = LCR_PAR_MARK;
2428 dev_dbg(dev, "%s - parity = mark\n", __func__);
2429 } else {
2430 lParity = LCR_PAR_SPACE;
2431 dev_dbg(dev, "%s - parity = space\n", __func__);
2432 }
2433 } else if (cflag & PARODD) {
2434 lParity = LCR_PAR_ODD;
2435 dev_dbg(dev, "%s - parity = odd\n", __func__);
2436 } else {
2437 lParity = LCR_PAR_EVEN;
2438 dev_dbg(dev, "%s - parity = even\n", __func__);
2439 }
2440 } else {
2441 dev_dbg(dev, "%s - parity = none\n", __func__);
2442 }
2443
2444 if (cflag & CSTOPB) {
2445 lStop = LCR_STOP_2;
2446 dev_dbg(dev, "%s - stop bits = 2\n", __func__);
2447 } else {
2448 lStop = LCR_STOP_1;
2449 dev_dbg(dev, "%s - stop bits = 1\n", __func__);
2450 }
2451
2452 /* figure out the flow control settings */
2453 rxFlow = txFlow = 0x00;
2454 if (cflag & CRTSCTS) {
2455 rxFlow |= IOSP_RX_FLOW_RTS;
2456 txFlow |= IOSP_TX_FLOW_CTS;
2457 dev_dbg(dev, "%s - RTS/CTS is enabled\n", __func__);
2458 } else {
2459 dev_dbg(dev, "%s - RTS/CTS is disabled\n", __func__);
2460 }
2461
2462 /* if we are implementing XON/XOFF, set the start and stop character
2463 in the device */
2464 if (I_IXOFF(tty) || I_IXON(tty)) {
2465 unsigned char stop_char = STOP_CHAR(tty);
2466 unsigned char start_char = START_CHAR(tty);
2467
2468 if ((!edge_serial->is_epic) ||
2469 ((edge_serial->is_epic) &&
2470 (edge_serial->epic_descriptor.Supports.IOSPSetXChar))) {
2471 send_iosp_ext_cmd(edge_port,
2472 IOSP_CMD_SET_XON_CHAR, start_char);
2473 send_iosp_ext_cmd(edge_port,
2474 IOSP_CMD_SET_XOFF_CHAR, stop_char);
2475 }
2476
2477 /* if we are implementing INBOUND XON/XOFF */
2478 if (I_IXOFF(tty)) {
2479 rxFlow |= IOSP_RX_FLOW_XON_XOFF;
2480 dev_dbg(dev, "%s - INBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n",
2481 __func__, start_char, stop_char);
2482 } else {
2483 dev_dbg(dev, "%s - INBOUND XON/XOFF is disabled\n", __func__);
2484 }
2485
2486 /* if we are implementing OUTBOUND XON/XOFF */
2487 if (I_IXON(tty)) {
2488 txFlow |= IOSP_TX_FLOW_XON_XOFF;
2489 dev_dbg(dev, "%s - OUTBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n",
2490 __func__, start_char, stop_char);
2491 } else {
2492 dev_dbg(dev, "%s - OUTBOUND XON/XOFF is disabled\n", __func__);
2493 }
2494 }
2495
2496 /* Set flow control to the configured value */
2497 if ((!edge_serial->is_epic) ||
2498 ((edge_serial->is_epic) &&
2499 (edge_serial->epic_descriptor.Supports.IOSPSetRxFlow)))
2500 send_iosp_ext_cmd(edge_port, IOSP_CMD_SET_RX_FLOW, rxFlow);
2501 if ((!edge_serial->is_epic) ||
2502 ((edge_serial->is_epic) &&
2503 (edge_serial->epic_descriptor.Supports.IOSPSetTxFlow)))
2504 send_iosp_ext_cmd(edge_port, IOSP_CMD_SET_TX_FLOW, txFlow);
2505
2506
2507 edge_port->shadowLCR &= ~(LCR_BITS_MASK | LCR_STOP_MASK | LCR_PAR_MASK);
2508 edge_port->shadowLCR |= (lData | lParity | lStop);
2509
2510 edge_port->validDataMask = mask;
2511
2512 /* Send the updated LCR value to the EdgePort */
2513 status = send_cmd_write_uart_register(edge_port, LCR,
2514 edge_port->shadowLCR);
2515 if (status != 0)
2516 return;
2517
2518 /* set up the MCR register and send it to the EdgePort */
2519 edge_port->shadowMCR = MCR_MASTER_IE;
2520 if (cflag & CBAUD)
2521 edge_port->shadowMCR |= (MCR_DTR | MCR_RTS);
2522
2523 status = send_cmd_write_uart_register(edge_port, MCR,
2524 edge_port->shadowMCR);
2525 if (status != 0)
2526 return;
2527
2528 /* Determine divisor based on baud rate */
2529 baud = tty_get_baud_rate(tty);
2530 if (!baud) {
2531 /* pick a default, any default... */
2532 baud = 9600;
2533 }
2534
2535 dev_dbg(dev, "%s - baud rate = %d\n", __func__, baud);
2536 status = send_cmd_write_baud_rate(edge_port, baud);
2537 if (status == -1) {
2538 /* Speed change was not possible - put back the old speed */
2539 baud = tty_termios_baud_rate(old_termios);
2540 tty_encode_baud_rate(tty, baud, baud);
2541 }
2542}
2543
2544
2545/****************************************************************************
2546 * unicode_to_ascii
2547 * Turns a string from Unicode into ASCII.
2548 * Doesn't do a good job with any characters that are outside the normal
2549 * ASCII range, but it's only for debugging...
2550 * NOTE: expects the unicode in LE format
2551 ****************************************************************************/
2552static void unicode_to_ascii(char *string, int buflen,
2553 __le16 *unicode, int unicode_size)
2554{
2555 int i;
2556
2557 if (buflen <= 0) /* never happens, but... */
2558 return;
2559 --buflen; /* space for nul */
2560
2561 for (i = 0; i < unicode_size; i++) {
2562 if (i >= buflen)
2563 break;
2564 string[i] = (char)(le16_to_cpu(unicode[i]));
2565 }
2566 string[i] = 0x00;
2567}
2568
2569
2570/****************************************************************************
2571 * get_manufacturing_desc
2572 * reads in the manufacturing descriptor and stores it into the serial
2573 * structure.
2574 ****************************************************************************/
2575static void get_manufacturing_desc(struct edgeport_serial *edge_serial)
2576{
2577 struct device *dev = &edge_serial->serial->dev->dev;
2578 int response;
2579
2580 dev_dbg(dev, "getting manufacturer descriptor\n");
2581
2582 response = rom_read(edge_serial->serial,
2583 (EDGE_MANUF_DESC_ADDR & 0xffff0000) >> 16,
2584 (__u16)(EDGE_MANUF_DESC_ADDR & 0x0000ffff),
2585 EDGE_MANUF_DESC_LEN,
2586 (__u8 *)(&edge_serial->manuf_descriptor));
2587
2588 if (response < 1)
2589 dev_err(dev, "error in getting manufacturer descriptor\n");
2590 else {
2591 char string[30];
2592 dev_dbg(dev, "**Manufacturer Descriptor\n");
2593 dev_dbg(dev, " RomSize: %dK\n",
2594 edge_serial->manuf_descriptor.RomSize);
2595 dev_dbg(dev, " RamSize: %dK\n",
2596 edge_serial->manuf_descriptor.RamSize);
2597 dev_dbg(dev, " CpuRev: %d\n",
2598 edge_serial->manuf_descriptor.CpuRev);
2599 dev_dbg(dev, " BoardRev: %d\n",
2600 edge_serial->manuf_descriptor.BoardRev);
2601 dev_dbg(dev, " NumPorts: %d\n",
2602 edge_serial->manuf_descriptor.NumPorts);
2603 dev_dbg(dev, " DescDate: %d/%d/%d\n",
2604 edge_serial->manuf_descriptor.DescDate[0],
2605 edge_serial->manuf_descriptor.DescDate[1],
2606 edge_serial->manuf_descriptor.DescDate[2]+1900);
2607 unicode_to_ascii(string, sizeof(string),
2608 edge_serial->manuf_descriptor.SerialNumber,
2609 edge_serial->manuf_descriptor.SerNumLength/2);
2610 dev_dbg(dev, " SerialNumber: %s\n", string);
2611 unicode_to_ascii(string, sizeof(string),
2612 edge_serial->manuf_descriptor.AssemblyNumber,
2613 edge_serial->manuf_descriptor.AssemblyNumLength/2);
2614 dev_dbg(dev, " AssemblyNumber: %s\n", string);
2615 unicode_to_ascii(string, sizeof(string),
2616 edge_serial->manuf_descriptor.OemAssyNumber,
2617 edge_serial->manuf_descriptor.OemAssyNumLength/2);
2618 dev_dbg(dev, " OemAssyNumber: %s\n", string);
2619 dev_dbg(dev, " UartType: %d\n",
2620 edge_serial->manuf_descriptor.UartType);
2621 dev_dbg(dev, " IonPid: %d\n",
2622 edge_serial->manuf_descriptor.IonPid);
2623 dev_dbg(dev, " IonConfig: %d\n",
2624 edge_serial->manuf_descriptor.IonConfig);
2625 }
2626}
2627
2628
2629/****************************************************************************
2630 * get_boot_desc
2631 * reads in the bootloader descriptor and stores it into the serial
2632 * structure.
2633 ****************************************************************************/
2634static void get_boot_desc(struct edgeport_serial *edge_serial)
2635{
2636 struct device *dev = &edge_serial->serial->dev->dev;
2637 int response;
2638
2639 dev_dbg(dev, "getting boot descriptor\n");
2640
2641 response = rom_read(edge_serial->serial,
2642 (EDGE_BOOT_DESC_ADDR & 0xffff0000) >> 16,
2643 (__u16)(EDGE_BOOT_DESC_ADDR & 0x0000ffff),
2644 EDGE_BOOT_DESC_LEN,
2645 (__u8 *)(&edge_serial->boot_descriptor));
2646
2647 if (response < 1)
2648 dev_err(dev, "error in getting boot descriptor\n");
2649 else {
2650 dev_dbg(dev, "**Boot Descriptor:\n");
2651 dev_dbg(dev, " BootCodeLength: %d\n",
2652 le16_to_cpu(edge_serial->boot_descriptor.BootCodeLength));
2653 dev_dbg(dev, " MajorVersion: %d\n",
2654 edge_serial->boot_descriptor.MajorVersion);
2655 dev_dbg(dev, " MinorVersion: %d\n",
2656 edge_serial->boot_descriptor.MinorVersion);
2657 dev_dbg(dev, " BuildNumber: %d\n",
2658 le16_to_cpu(edge_serial->boot_descriptor.BuildNumber));
2659 dev_dbg(dev, " Capabilities: 0x%x\n",
2660 le16_to_cpu(edge_serial->boot_descriptor.Capabilities));
2661 dev_dbg(dev, " UConfig0: %d\n",
2662 edge_serial->boot_descriptor.UConfig0);
2663 dev_dbg(dev, " UConfig1: %d\n",
2664 edge_serial->boot_descriptor.UConfig1);
2665 }
2666}
2667
2668
2669/****************************************************************************
2670 * load_application_firmware
2671 * This is called to load the application firmware to the device
2672 ****************************************************************************/
2673static void load_application_firmware(struct edgeport_serial *edge_serial)
2674{
2675 struct device *dev = &edge_serial->serial->dev->dev;
2676 const struct ihex_binrec *rec;
2677 const struct firmware *fw;
2678 const char *fw_name;
2679 const char *fw_info;
2680 int response;
2681 __u32 Operaddr;
2682 __u16 build;
2683
2684 switch (edge_serial->product_info.iDownloadFile) {
2685 case EDGE_DOWNLOAD_FILE_I930:
2686 fw_info = "downloading firmware version (930)";
2687 fw_name = "edgeport/down.fw";
2688 break;
2689
2690 case EDGE_DOWNLOAD_FILE_80251:
2691 fw_info = "downloading firmware version (80251)";
2692 fw_name = "edgeport/down2.fw";
2693 break;
2694
2695 case EDGE_DOWNLOAD_FILE_NONE:
2696 dev_dbg(dev, "No download file specified, skipping download\n");
2697 return;
2698
2699 default:
2700 return;
2701 }
2702
2703 response = request_ihex_firmware(&fw, fw_name,
2704 &edge_serial->serial->dev->dev);
2705 if (response) {
2706 dev_err(dev, "Failed to load image \"%s\" err %d\n",
2707 fw_name, response);
2708 return;
2709 }
2710
2711 rec = (const struct ihex_binrec *)fw->data;
2712 build = (rec->data[2] << 8) | rec->data[3];
2713
2714 dev_dbg(dev, "%s %d.%d.%d\n", fw_info, rec->data[0], rec->data[1], build);
2715
2716 edge_serial->product_info.FirmwareMajorVersion = rec->data[0];
2717 edge_serial->product_info.FirmwareMinorVersion = rec->data[1];
2718 edge_serial->product_info.FirmwareBuildNumber = cpu_to_le16(build);
2719
2720 for (rec = ihex_next_binrec(rec); rec;
2721 rec = ihex_next_binrec(rec)) {
2722 Operaddr = be32_to_cpu(rec->addr);
2723 response = sram_write(edge_serial->serial,
2724 Operaddr >> 16,
2725 Operaddr & 0xFFFF,
2726 be16_to_cpu(rec->len),
2727 &rec->data[0]);
2728 if (response < 0) {
2729 dev_err(&edge_serial->serial->dev->dev,
2730 "sram_write failed (%x, %x, %d)\n",
2731 Operaddr >> 16, Operaddr & 0xFFFF,
2732 be16_to_cpu(rec->len));
2733 break;
2734 }
2735 }
2736
2737 dev_dbg(dev, "sending exec_dl_code\n");
2738 response = usb_control_msg (edge_serial->serial->dev,
2739 usb_sndctrlpipe(edge_serial->serial->dev, 0),
2740 USB_REQUEST_ION_EXEC_DL_CODE,
2741 0x40, 0x4000, 0x0001, NULL, 0, 3000);
2742
2743 release_firmware(fw);
2744}
2745
2746
2747/****************************************************************************
2748 * edge_startup
2749 ****************************************************************************/
2750static int edge_startup(struct usb_serial *serial)
2751{
2752 struct edgeport_serial *edge_serial;
2753 struct usb_device *dev;
2754 struct device *ddev = &serial->dev->dev;
2755 int i;
2756 int response;
2757 bool interrupt_in_found;
2758 bool bulk_in_found;
2759 bool bulk_out_found;
2760 static __u32 descriptor[3] = { EDGE_COMPATIBILITY_MASK0,
2761 EDGE_COMPATIBILITY_MASK1,
2762 EDGE_COMPATIBILITY_MASK2 };
2763
2764 dev = serial->dev;
2765
2766 /* create our private serial structure */
2767 edge_serial = kzalloc(sizeof(struct edgeport_serial), GFP_KERNEL);
2768 if (!edge_serial)
2769 return -ENOMEM;
2770
2771 spin_lock_init(&edge_serial->es_lock);
2772 edge_serial->serial = serial;
2773 usb_set_serial_data(serial, edge_serial);
2774
2775 /* get the name for the device from the device */
2776 i = usb_string(dev, dev->descriptor.iManufacturer,
2777 &edge_serial->name[0], MAX_NAME_LEN+1);
2778 if (i < 0)
2779 i = 0;
2780 edge_serial->name[i++] = ' ';
2781 usb_string(dev, dev->descriptor.iProduct,
2782 &edge_serial->name[i], MAX_NAME_LEN+2 - i);
2783
2784 dev_info(&serial->dev->dev, "%s detected\n", edge_serial->name);
2785
2786 /* Read the epic descriptor */
2787 if (get_epic_descriptor(edge_serial) <= 0) {
2788 /* memcpy descriptor to Supports structures */
2789 memcpy(&edge_serial->epic_descriptor.Supports, descriptor,
2790 sizeof(struct edge_compatibility_bits));
2791
2792 /* get the manufacturing descriptor for this device */
2793 get_manufacturing_desc(edge_serial);
2794
2795 /* get the boot descriptor */
2796 get_boot_desc(edge_serial);
2797
2798 get_product_info(edge_serial);
2799 }
2800
2801 /* set the number of ports from the manufacturing description */
2802 /* serial->num_ports = serial->product_info.NumPorts; */
2803 if ((!edge_serial->is_epic) &&
2804 (edge_serial->product_info.NumPorts != serial->num_ports)) {
2805 dev_warn(ddev,
2806 "Device Reported %d serial ports vs. core thinking we have %d ports, email greg@kroah.com this information.\n",
2807 edge_serial->product_info.NumPorts,
2808 serial->num_ports);
2809 }
2810
2811 dev_dbg(ddev, "%s - time 1 %ld\n", __func__, jiffies);
2812
2813 /* If not an EPiC device */
2814 if (!edge_serial->is_epic) {
2815 /* now load the application firmware into this device */
2816 load_application_firmware(edge_serial);
2817
2818 dev_dbg(ddev, "%s - time 2 %ld\n", __func__, jiffies);
2819
2820 /* Check current Edgeport EEPROM and update if necessary */
2821 update_edgeport_E2PROM(edge_serial);
2822
2823 dev_dbg(ddev, "%s - time 3 %ld\n", __func__, jiffies);
2824
2825 /* set the configuration to use #1 */
2826/* dev_dbg(ddev, "set_configuration 1\n"); */
2827/* usb_set_configuration (dev, 1); */
2828 }
2829 dev_dbg(ddev, " FirmwareMajorVersion %d.%d.%d\n",
2830 edge_serial->product_info.FirmwareMajorVersion,
2831 edge_serial->product_info.FirmwareMinorVersion,
2832 le16_to_cpu(edge_serial->product_info.FirmwareBuildNumber));
2833
2834 /* we set up the pointers to the endpoints in the edge_open function,
2835 * as the structures aren't created yet. */
2836
2837 response = 0;
2838
2839 if (edge_serial->is_epic) {
2840 /* EPIC thing, set up our interrupt polling now and our read
2841 * urb, so that the device knows it really is connected. */
2842 interrupt_in_found = bulk_in_found = bulk_out_found = false;
2843 for (i = 0; i < serial->interface->altsetting[0]
2844 .desc.bNumEndpoints; ++i) {
2845 struct usb_endpoint_descriptor *endpoint;
2846 int buffer_size;
2847
2848 endpoint = &serial->interface->altsetting[0].
2849 endpoint[i].desc;
2850 buffer_size = usb_endpoint_maxp(endpoint);
2851 if (!interrupt_in_found &&
2852 (usb_endpoint_is_int_in(endpoint))) {
2853 /* we found a interrupt in endpoint */
2854 dev_dbg(ddev, "found interrupt in\n");
2855
2856 /* not set up yet, so do it now */
2857 edge_serial->interrupt_read_urb =
2858 usb_alloc_urb(0, GFP_KERNEL);
2859 if (!edge_serial->interrupt_read_urb)
2860 return -ENOMEM;
2861
2862 edge_serial->interrupt_in_buffer =
2863 kmalloc(buffer_size, GFP_KERNEL);
2864 if (!edge_serial->interrupt_in_buffer) {
2865 usb_free_urb(edge_serial->interrupt_read_urb);
2866 return -ENOMEM;
2867 }
2868 edge_serial->interrupt_in_endpoint =
2869 endpoint->bEndpointAddress;
2870
2871 /* set up our interrupt urb */
2872 usb_fill_int_urb(
2873 edge_serial->interrupt_read_urb,
2874 dev,
2875 usb_rcvintpipe(dev,
2876 endpoint->bEndpointAddress),
2877 edge_serial->interrupt_in_buffer,
2878 buffer_size,
2879 edge_interrupt_callback,
2880 edge_serial,
2881 endpoint->bInterval);
2882
2883 interrupt_in_found = true;
2884 }
2885
2886 if (!bulk_in_found &&
2887 (usb_endpoint_is_bulk_in(endpoint))) {
2888 /* we found a bulk in endpoint */
2889 dev_dbg(ddev, "found bulk in\n");
2890
2891 /* not set up yet, so do it now */
2892 edge_serial->read_urb =
2893 usb_alloc_urb(0, GFP_KERNEL);
2894 if (!edge_serial->read_urb)
2895 return -ENOMEM;
2896
2897 edge_serial->bulk_in_buffer =
2898 kmalloc(buffer_size, GFP_KERNEL);
2899 if (!edge_serial->bulk_in_buffer) {
2900 usb_free_urb(edge_serial->read_urb);
2901 return -ENOMEM;
2902 }
2903 edge_serial->bulk_in_endpoint =
2904 endpoint->bEndpointAddress;
2905
2906 /* set up our bulk in urb */
2907 usb_fill_bulk_urb(edge_serial->read_urb, dev,
2908 usb_rcvbulkpipe(dev,
2909 endpoint->bEndpointAddress),
2910 edge_serial->bulk_in_buffer,
2911 usb_endpoint_maxp(endpoint),
2912 edge_bulk_in_callback,
2913 edge_serial);
2914 bulk_in_found = true;
2915 }
2916
2917 if (!bulk_out_found &&
2918 (usb_endpoint_is_bulk_out(endpoint))) {
2919 /* we found a bulk out endpoint */
2920 dev_dbg(ddev, "found bulk out\n");
2921 edge_serial->bulk_out_endpoint =
2922 endpoint->bEndpointAddress;
2923 bulk_out_found = true;
2924 }
2925 }
2926
2927 if (!interrupt_in_found || !bulk_in_found || !bulk_out_found) {
2928 dev_err(ddev, "Error - the proper endpoints were not found!\n");
2929 return -ENODEV;
2930 }
2931
2932 /* start interrupt read for this edgeport this interrupt will
2933 * continue as long as the edgeport is connected */
2934 response = usb_submit_urb(edge_serial->interrupt_read_urb,
2935 GFP_KERNEL);
2936 if (response)
2937 dev_err(ddev, "%s - Error %d submitting control urb\n",
2938 __func__, response);
2939 }
2940 return response;
2941}
2942
2943
2944/****************************************************************************
2945 * edge_disconnect
2946 * This function is called whenever the device is removed from the usb bus.
2947 ****************************************************************************/
2948static void edge_disconnect(struct usb_serial *serial)
2949{
2950 struct edgeport_serial *edge_serial = usb_get_serial_data(serial);
2951
2952 /* stop reads and writes on all ports */
2953 /* free up our endpoint stuff */
2954 if (edge_serial->is_epic) {
2955 usb_kill_urb(edge_serial->interrupt_read_urb);
2956 usb_free_urb(edge_serial->interrupt_read_urb);
2957 kfree(edge_serial->interrupt_in_buffer);
2958
2959 usb_kill_urb(edge_serial->read_urb);
2960 usb_free_urb(edge_serial->read_urb);
2961 kfree(edge_serial->bulk_in_buffer);
2962 }
2963}
2964
2965
2966/****************************************************************************
2967 * edge_release
2968 * This function is called when the device structure is deallocated.
2969 ****************************************************************************/
2970static void edge_release(struct usb_serial *serial)
2971{
2972 struct edgeport_serial *edge_serial = usb_get_serial_data(serial);
2973
2974 kfree(edge_serial);
2975}
2976
2977static int edge_port_probe(struct usb_serial_port *port)
2978{
2979 struct edgeport_port *edge_port;
2980
2981 edge_port = kzalloc(sizeof(*edge_port), GFP_KERNEL);
2982 if (!edge_port)
2983 return -ENOMEM;
2984
2985 spin_lock_init(&edge_port->ep_lock);
2986 edge_port->port = port;
2987
2988 usb_set_serial_port_data(port, edge_port);
2989
2990 return 0;
2991}
2992
2993static int edge_port_remove(struct usb_serial_port *port)
2994{
2995 struct edgeport_port *edge_port;
2996
2997 edge_port = usb_get_serial_port_data(port);
2998 kfree(edge_port);
2999
3000 return 0;
3001}
3002
3003module_usb_serial_driver(serial_drivers, id_table_combined);
3004
3005MODULE_AUTHOR(DRIVER_AUTHOR);
3006MODULE_DESCRIPTION(DRIVER_DESC);
3007MODULE_LICENSE("GPL");
3008MODULE_FIRMWARE("edgeport/boot.fw");
3009MODULE_FIRMWARE("edgeport/boot2.fw");
3010MODULE_FIRMWARE("edgeport/down.fw");
3011MODULE_FIRMWARE("edgeport/down2.fw");