Loading...
1// SPDX-License-Identifier: GPL-2.0
2/* sunzilog.c: Zilog serial driver for Sparc systems.
3 *
4 * Driver for Zilog serial chips found on Sun workstations and
5 * servers. This driver could actually be made more generic.
6 *
7 * This is based on the old drivers/sbus/char/zs.c code. A lot
8 * of code has been simply moved over directly from there but
9 * much has been rewritten. Credits therefore go out to Eddie
10 * C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell for their
11 * work there.
12 *
13 * Copyright (C) 2002, 2006, 2007 David S. Miller (davem@davemloft.net)
14 */
15
16#include <linux/module.h>
17#include <linux/kernel.h>
18#include <linux/errno.h>
19#include <linux/delay.h>
20#include <linux/tty.h>
21#include <linux/tty_flip.h>
22#include <linux/major.h>
23#include <linux/string.h>
24#include <linux/ptrace.h>
25#include <linux/ioport.h>
26#include <linux/slab.h>
27#include <linux/circ_buf.h>
28#include <linux/serial.h>
29#include <linux/sysrq.h>
30#include <linux/console.h>
31#include <linux/spinlock.h>
32#ifdef CONFIG_SERIO
33#include <linux/serio.h>
34#endif
35#include <linux/init.h>
36#include <linux/of.h>
37#include <linux/platform_device.h>
38
39#include <linux/io.h>
40#include <asm/irq.h>
41#include <asm/setup.h>
42
43#include <linux/serial_core.h>
44#include <linux/sunserialcore.h>
45
46#include "sunzilog.h"
47
48/* On 32-bit sparcs we need to delay after register accesses
49 * to accommodate sun4 systems, but we do not need to flush writes.
50 * On 64-bit sparc we only need to flush single writes to ensure
51 * completion.
52 */
53#ifndef CONFIG_SPARC64
54#define ZSDELAY() udelay(5)
55#define ZSDELAY_LONG() udelay(20)
56#define ZS_WSYNC(channel) do { } while (0)
57#else
58#define ZSDELAY()
59#define ZSDELAY_LONG()
60#define ZS_WSYNC(__channel) \
61 readb(&((__channel)->control))
62#endif
63
64#define ZS_CLOCK 4915200 /* Zilog input clock rate. */
65#define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */
66
67/*
68 * We wrap our port structure around the generic uart_port.
69 */
70struct uart_sunzilog_port {
71 struct uart_port port;
72
73 /* IRQ servicing chain. */
74 struct uart_sunzilog_port *next;
75
76 /* Current values of Zilog write registers. */
77 unsigned char curregs[NUM_ZSREGS];
78
79 unsigned int flags;
80#define SUNZILOG_FLAG_CONS_KEYB 0x00000001
81#define SUNZILOG_FLAG_CONS_MOUSE 0x00000002
82#define SUNZILOG_FLAG_IS_CONS 0x00000004
83#define SUNZILOG_FLAG_IS_KGDB 0x00000008
84#define SUNZILOG_FLAG_MODEM_STATUS 0x00000010
85#define SUNZILOG_FLAG_IS_CHANNEL_A 0x00000020
86#define SUNZILOG_FLAG_REGS_HELD 0x00000040
87#define SUNZILOG_FLAG_TX_STOPPED 0x00000080
88#define SUNZILOG_FLAG_TX_ACTIVE 0x00000100
89#define SUNZILOG_FLAG_ESCC 0x00000200
90#define SUNZILOG_FLAG_ISR_HANDLER 0x00000400
91
92 unsigned int cflag;
93
94 unsigned char parity_mask;
95 unsigned char prev_status;
96
97#ifdef CONFIG_SERIO
98 struct serio serio;
99 int serio_open;
100#endif
101};
102
103static void sunzilog_putchar(struct uart_port *port, unsigned char ch);
104
105#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel __iomem *)((PORT)->membase))
106#define UART_ZILOG(PORT) ((struct uart_sunzilog_port *)(PORT))
107
108#define ZS_IS_KEYB(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_KEYB)
109#define ZS_IS_MOUSE(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_MOUSE)
110#define ZS_IS_CONS(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CONS)
111#define ZS_IS_KGDB(UP) ((UP)->flags & SUNZILOG_FLAG_IS_KGDB)
112#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & SUNZILOG_FLAG_MODEM_STATUS)
113#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CHANNEL_A)
114#define ZS_REGS_HELD(UP) ((UP)->flags & SUNZILOG_FLAG_REGS_HELD)
115#define ZS_TX_STOPPED(UP) ((UP)->flags & SUNZILOG_FLAG_TX_STOPPED)
116#define ZS_TX_ACTIVE(UP) ((UP)->flags & SUNZILOG_FLAG_TX_ACTIVE)
117
118/* Reading and writing Zilog8530 registers. The delays are to make this
119 * driver work on the Sun4 which needs a settling delay after each chip
120 * register access, other machines handle this in hardware via auxiliary
121 * flip-flops which implement the settle time we do in software.
122 *
123 * The port lock must be held and local IRQs must be disabled
124 * when {read,write}_zsreg is invoked.
125 */
126static unsigned char read_zsreg(struct zilog_channel __iomem *channel,
127 unsigned char reg)
128{
129 unsigned char retval;
130
131 writeb(reg, &channel->control);
132 ZSDELAY();
133 retval = readb(&channel->control);
134 ZSDELAY();
135
136 return retval;
137}
138
139static void write_zsreg(struct zilog_channel __iomem *channel,
140 unsigned char reg, unsigned char value)
141{
142 writeb(reg, &channel->control);
143 ZSDELAY();
144 writeb(value, &channel->control);
145 ZSDELAY();
146}
147
148static void sunzilog_clear_fifo(struct zilog_channel __iomem *channel)
149{
150 int i;
151
152 for (i = 0; i < 32; i++) {
153 unsigned char regval;
154
155 regval = readb(&channel->control);
156 ZSDELAY();
157 if (regval & Rx_CH_AV)
158 break;
159
160 regval = read_zsreg(channel, R1);
161 readb(&channel->data);
162 ZSDELAY();
163
164 if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) {
165 writeb(ERR_RES, &channel->control);
166 ZSDELAY();
167 ZS_WSYNC(channel);
168 }
169 }
170}
171
172/* This function must only be called when the TX is not busy. The UART
173 * port lock must be held and local interrupts disabled.
174 */
175static int __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *regs)
176{
177 int i;
178 int escc;
179 unsigned char r15;
180
181 /* Let pending transmits finish. */
182 for (i = 0; i < 1000; i++) {
183 unsigned char stat = read_zsreg(channel, R1);
184 if (stat & ALL_SNT)
185 break;
186 udelay(100);
187 }
188
189 writeb(ERR_RES, &channel->control);
190 ZSDELAY();
191 ZS_WSYNC(channel);
192
193 sunzilog_clear_fifo(channel);
194
195 /* Disable all interrupts. */
196 write_zsreg(channel, R1,
197 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
198
199 /* Set parity, sync config, stop bits, and clock divisor. */
200 write_zsreg(channel, R4, regs[R4]);
201
202 /* Set misc. TX/RX control bits. */
203 write_zsreg(channel, R10, regs[R10]);
204
205 /* Set TX/RX controls sans the enable bits. */
206 write_zsreg(channel, R3, regs[R3] & ~RxENAB);
207 write_zsreg(channel, R5, regs[R5] & ~TxENAB);
208
209 /* Synchronous mode config. */
210 write_zsreg(channel, R6, regs[R6]);
211 write_zsreg(channel, R7, regs[R7]);
212
213 /* Don't mess with the interrupt vector (R2, unused by us) and
214 * master interrupt control (R9). We make sure this is setup
215 * properly at probe time then never touch it again.
216 */
217
218 /* Disable baud generator. */
219 write_zsreg(channel, R14, regs[R14] & ~BRENAB);
220
221 /* Clock mode control. */
222 write_zsreg(channel, R11, regs[R11]);
223
224 /* Lower and upper byte of baud rate generator divisor. */
225 write_zsreg(channel, R12, regs[R12]);
226 write_zsreg(channel, R13, regs[R13]);
227
228 /* Now rewrite R14, with BRENAB (if set). */
229 write_zsreg(channel, R14, regs[R14]);
230
231 /* External status interrupt control. */
232 write_zsreg(channel, R15, (regs[R15] | WR7pEN) & ~FIFOEN);
233
234 /* ESCC Extension Register */
235 r15 = read_zsreg(channel, R15);
236 if (r15 & 0x01) {
237 write_zsreg(channel, R7, regs[R7p]);
238
239 /* External status interrupt and FIFO control. */
240 write_zsreg(channel, R15, regs[R15] & ~WR7pEN);
241 escc = 1;
242 } else {
243 /* Clear FIFO bit case it is an issue */
244 regs[R15] &= ~FIFOEN;
245 escc = 0;
246 }
247
248 /* Reset external status interrupts. */
249 write_zsreg(channel, R0, RES_EXT_INT); /* First Latch */
250 write_zsreg(channel, R0, RES_EXT_INT); /* Second Latch */
251
252 /* Rewrite R3/R5, this time without enables masked. */
253 write_zsreg(channel, R3, regs[R3]);
254 write_zsreg(channel, R5, regs[R5]);
255
256 /* Rewrite R1, this time without IRQ enabled masked. */
257 write_zsreg(channel, R1, regs[R1]);
258
259 return escc;
260}
261
262/* Reprogram the Zilog channel HW registers with the copies found in the
263 * software state struct. If the transmitter is busy, we defer this update
264 * until the next TX complete interrupt. Else, we do it right now.
265 *
266 * The UART port lock must be held and local interrupts disabled.
267 */
268static void sunzilog_maybe_update_regs(struct uart_sunzilog_port *up,
269 struct zilog_channel __iomem *channel)
270{
271 if (!ZS_REGS_HELD(up)) {
272 if (ZS_TX_ACTIVE(up)) {
273 up->flags |= SUNZILOG_FLAG_REGS_HELD;
274 } else {
275 __load_zsregs(channel, up->curregs);
276 }
277 }
278}
279
280static void sunzilog_change_mouse_baud(struct uart_sunzilog_port *up)
281{
282 unsigned int cur_cflag = up->cflag;
283 int brg, new_baud;
284
285 up->cflag &= ~CBAUD;
286 up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud);
287
288 brg = BPS_TO_BRG(new_baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
289 up->curregs[R12] = (brg & 0xff);
290 up->curregs[R13] = (brg >> 8) & 0xff;
291 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(&up->port));
292}
293
294static void sunzilog_kbdms_receive_chars(struct uart_sunzilog_port *up,
295 unsigned char ch, int is_break)
296{
297 if (ZS_IS_KEYB(up)) {
298 /* Stop-A is handled by drivers/char/keyboard.c now. */
299#ifdef CONFIG_SERIO
300 if (up->serio_open)
301 serio_interrupt(&up->serio, ch, 0);
302#endif
303 } else if (ZS_IS_MOUSE(up)) {
304 int ret = suncore_mouse_baud_detection(ch, is_break);
305
306 switch (ret) {
307 case 2:
308 sunzilog_change_mouse_baud(up);
309 fallthrough;
310 case 1:
311 break;
312
313 case 0:
314#ifdef CONFIG_SERIO
315 if (up->serio_open)
316 serio_interrupt(&up->serio, ch, 0);
317#endif
318 break;
319 }
320 }
321}
322
323static struct tty_port *
324sunzilog_receive_chars(struct uart_sunzilog_port *up,
325 struct zilog_channel __iomem *channel)
326{
327 struct tty_port *port = NULL;
328 unsigned char ch, r1, flag;
329
330 if (up->port.state != NULL) /* Unopened serial console */
331 port = &up->port.state->port;
332
333 for (;;) {
334
335 r1 = read_zsreg(channel, R1);
336 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
337 writeb(ERR_RES, &channel->control);
338 ZSDELAY();
339 ZS_WSYNC(channel);
340 }
341
342 ch = readb(&channel->control);
343 ZSDELAY();
344
345 /* This funny hack depends upon BRK_ABRT not interfering
346 * with the other bits we care about in R1.
347 */
348 if (ch & BRK_ABRT)
349 r1 |= BRK_ABRT;
350
351 if (!(ch & Rx_CH_AV))
352 break;
353
354 ch = readb(&channel->data);
355 ZSDELAY();
356
357 ch &= up->parity_mask;
358
359 if (unlikely(ZS_IS_KEYB(up)) || unlikely(ZS_IS_MOUSE(up))) {
360 sunzilog_kbdms_receive_chars(up, ch, 0);
361 continue;
362 }
363
364 /* A real serial line, record the character and status. */
365 flag = TTY_NORMAL;
366 up->port.icount.rx++;
367 if (r1 & (BRK_ABRT | PAR_ERR | Rx_OVR | CRC_ERR)) {
368 if (r1 & BRK_ABRT) {
369 r1 &= ~(PAR_ERR | CRC_ERR);
370 up->port.icount.brk++;
371 if (uart_handle_break(&up->port))
372 continue;
373 }
374 else if (r1 & PAR_ERR)
375 up->port.icount.parity++;
376 else if (r1 & CRC_ERR)
377 up->port.icount.frame++;
378 if (r1 & Rx_OVR)
379 up->port.icount.overrun++;
380 r1 &= up->port.read_status_mask;
381 if (r1 & BRK_ABRT)
382 flag = TTY_BREAK;
383 else if (r1 & PAR_ERR)
384 flag = TTY_PARITY;
385 else if (r1 & CRC_ERR)
386 flag = TTY_FRAME;
387 }
388 if (uart_handle_sysrq_char(&up->port, ch) || !port)
389 continue;
390
391 if (up->port.ignore_status_mask == 0xff ||
392 (r1 & up->port.ignore_status_mask) == 0) {
393 tty_insert_flip_char(port, ch, flag);
394 }
395 if (r1 & Rx_OVR)
396 tty_insert_flip_char(port, 0, TTY_OVERRUN);
397 }
398
399 return port;
400}
401
402static void sunzilog_status_handle(struct uart_sunzilog_port *up,
403 struct zilog_channel __iomem *channel)
404{
405 unsigned char status;
406
407 status = readb(&channel->control);
408 ZSDELAY();
409
410 writeb(RES_EXT_INT, &channel->control);
411 ZSDELAY();
412 ZS_WSYNC(channel);
413
414 if (status & BRK_ABRT) {
415 if (ZS_IS_MOUSE(up))
416 sunzilog_kbdms_receive_chars(up, 0, 1);
417 if (ZS_IS_CONS(up)) {
418 /* Wait for BREAK to deassert to avoid potentially
419 * confusing the PROM.
420 */
421 while (1) {
422 status = readb(&channel->control);
423 ZSDELAY();
424 if (!(status & BRK_ABRT))
425 break;
426 }
427 sun_do_break();
428 return;
429 }
430 }
431
432 if (ZS_WANTS_MODEM_STATUS(up)) {
433 if (status & SYNC)
434 up->port.icount.dsr++;
435
436 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
437 * But it does not tell us which bit has changed, we have to keep
438 * track of this ourselves.
439 */
440 if ((status ^ up->prev_status) ^ DCD)
441 uart_handle_dcd_change(&up->port,
442 (status & DCD));
443 if ((status ^ up->prev_status) ^ CTS)
444 uart_handle_cts_change(&up->port,
445 (status & CTS));
446
447 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
448 }
449
450 up->prev_status = status;
451}
452
453static void sunzilog_transmit_chars(struct uart_sunzilog_port *up,
454 struct zilog_channel __iomem *channel)
455{
456 struct circ_buf *xmit;
457
458 if (ZS_IS_CONS(up)) {
459 unsigned char status = readb(&channel->control);
460 ZSDELAY();
461
462 /* TX still busy? Just wait for the next TX done interrupt.
463 *
464 * It can occur because of how we do serial console writes. It would
465 * be nice to transmit console writes just like we normally would for
466 * a TTY line. (ie. buffered and TX interrupt driven). That is not
467 * easy because console writes cannot sleep. One solution might be
468 * to poll on enough port->xmit space becoming free. -DaveM
469 */
470 if (!(status & Tx_BUF_EMP))
471 return;
472 }
473
474 up->flags &= ~SUNZILOG_FLAG_TX_ACTIVE;
475
476 if (ZS_REGS_HELD(up)) {
477 __load_zsregs(channel, up->curregs);
478 up->flags &= ~SUNZILOG_FLAG_REGS_HELD;
479 }
480
481 if (ZS_TX_STOPPED(up)) {
482 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED;
483 goto ack_tx_int;
484 }
485
486 if (up->port.x_char) {
487 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
488 writeb(up->port.x_char, &channel->data);
489 ZSDELAY();
490 ZS_WSYNC(channel);
491
492 up->port.icount.tx++;
493 up->port.x_char = 0;
494 return;
495 }
496
497 if (up->port.state == NULL)
498 goto ack_tx_int;
499 xmit = &up->port.state->xmit;
500 if (uart_circ_empty(xmit))
501 goto ack_tx_int;
502
503 if (uart_tx_stopped(&up->port))
504 goto ack_tx_int;
505
506 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
507 writeb(xmit->buf[xmit->tail], &channel->data);
508 ZSDELAY();
509 ZS_WSYNC(channel);
510
511 uart_xmit_advance(&up->port, 1);
512
513 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
514 uart_write_wakeup(&up->port);
515
516 return;
517
518ack_tx_int:
519 writeb(RES_Tx_P, &channel->control);
520 ZSDELAY();
521 ZS_WSYNC(channel);
522}
523
524static irqreturn_t sunzilog_interrupt(int irq, void *dev_id)
525{
526 struct uart_sunzilog_port *up = dev_id;
527
528 while (up) {
529 struct zilog_channel __iomem *channel
530 = ZILOG_CHANNEL_FROM_PORT(&up->port);
531 struct tty_port *port;
532 unsigned char r3;
533
534 uart_port_lock(&up->port);
535 r3 = read_zsreg(channel, R3);
536
537 /* Channel A */
538 port = NULL;
539 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
540 writeb(RES_H_IUS, &channel->control);
541 ZSDELAY();
542 ZS_WSYNC(channel);
543
544 if (r3 & CHARxIP)
545 port = sunzilog_receive_chars(up, channel);
546 if (r3 & CHAEXT)
547 sunzilog_status_handle(up, channel);
548 if (r3 & CHATxIP)
549 sunzilog_transmit_chars(up, channel);
550 }
551 uart_port_unlock(&up->port);
552
553 if (port)
554 tty_flip_buffer_push(port);
555
556 /* Channel B */
557 up = up->next;
558 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
559
560 uart_port_lock(&up->port);
561 port = NULL;
562 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
563 writeb(RES_H_IUS, &channel->control);
564 ZSDELAY();
565 ZS_WSYNC(channel);
566
567 if (r3 & CHBRxIP)
568 port = sunzilog_receive_chars(up, channel);
569 if (r3 & CHBEXT)
570 sunzilog_status_handle(up, channel);
571 if (r3 & CHBTxIP)
572 sunzilog_transmit_chars(up, channel);
573 }
574 uart_port_unlock(&up->port);
575
576 if (port)
577 tty_flip_buffer_push(port);
578
579 up = up->next;
580 }
581
582 return IRQ_HANDLED;
583}
584
585/* A convenient way to quickly get R0 status. The caller must _not_ hold the
586 * port lock, it is acquired here.
587 */
588static __inline__ unsigned char sunzilog_read_channel_status(struct uart_port *port)
589{
590 struct zilog_channel __iomem *channel;
591 unsigned char status;
592
593 channel = ZILOG_CHANNEL_FROM_PORT(port);
594 status = readb(&channel->control);
595 ZSDELAY();
596
597 return status;
598}
599
600/* The port lock is not held. */
601static unsigned int sunzilog_tx_empty(struct uart_port *port)
602{
603 unsigned long flags;
604 unsigned char status;
605 unsigned int ret;
606
607 uart_port_lock_irqsave(port, &flags);
608
609 status = sunzilog_read_channel_status(port);
610
611 uart_port_unlock_irqrestore(port, flags);
612
613 if (status & Tx_BUF_EMP)
614 ret = TIOCSER_TEMT;
615 else
616 ret = 0;
617
618 return ret;
619}
620
621/* The port lock is held and interrupts are disabled. */
622static unsigned int sunzilog_get_mctrl(struct uart_port *port)
623{
624 unsigned char status;
625 unsigned int ret;
626
627 status = sunzilog_read_channel_status(port);
628
629 ret = 0;
630 if (status & DCD)
631 ret |= TIOCM_CAR;
632 if (status & SYNC)
633 ret |= TIOCM_DSR;
634 if (status & CTS)
635 ret |= TIOCM_CTS;
636
637 return ret;
638}
639
640/* The port lock is held and interrupts are disabled. */
641static void sunzilog_set_mctrl(struct uart_port *port, unsigned int mctrl)
642{
643 struct uart_sunzilog_port *up =
644 container_of(port, struct uart_sunzilog_port, port);
645 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
646 unsigned char set_bits, clear_bits;
647
648 set_bits = clear_bits = 0;
649
650 if (mctrl & TIOCM_RTS)
651 set_bits |= RTS;
652 else
653 clear_bits |= RTS;
654 if (mctrl & TIOCM_DTR)
655 set_bits |= DTR;
656 else
657 clear_bits |= DTR;
658
659 /* NOTE: Not subject to 'transmitter active' rule. */
660 up->curregs[R5] |= set_bits;
661 up->curregs[R5] &= ~clear_bits;
662 write_zsreg(channel, R5, up->curregs[R5]);
663}
664
665/* The port lock is held and interrupts are disabled. */
666static void sunzilog_stop_tx(struct uart_port *port)
667{
668 struct uart_sunzilog_port *up =
669 container_of(port, struct uart_sunzilog_port, port);
670
671 up->flags |= SUNZILOG_FLAG_TX_STOPPED;
672}
673
674/* The port lock is held and interrupts are disabled. */
675static void sunzilog_start_tx(struct uart_port *port)
676{
677 struct uart_sunzilog_port *up =
678 container_of(port, struct uart_sunzilog_port, port);
679 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
680 unsigned char status;
681
682 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
683 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED;
684
685 status = readb(&channel->control);
686 ZSDELAY();
687
688 /* TX busy? Just wait for the TX done interrupt. */
689 if (!(status & Tx_BUF_EMP))
690 return;
691
692 /* Send the first character to jump-start the TX done
693 * IRQ sending engine.
694 */
695 if (port->x_char) {
696 writeb(port->x_char, &channel->data);
697 ZSDELAY();
698 ZS_WSYNC(channel);
699
700 port->icount.tx++;
701 port->x_char = 0;
702 } else {
703 struct circ_buf *xmit = &port->state->xmit;
704
705 if (uart_circ_empty(xmit))
706 return;
707 writeb(xmit->buf[xmit->tail], &channel->data);
708 ZSDELAY();
709 ZS_WSYNC(channel);
710
711 uart_xmit_advance(port, 1);
712
713 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
714 uart_write_wakeup(&up->port);
715 }
716}
717
718/* The port lock is held. */
719static void sunzilog_stop_rx(struct uart_port *port)
720{
721 struct uart_sunzilog_port *up = UART_ZILOG(port);
722 struct zilog_channel __iomem *channel;
723
724 if (ZS_IS_CONS(up))
725 return;
726
727 channel = ZILOG_CHANNEL_FROM_PORT(port);
728
729 /* Disable all RX interrupts. */
730 up->curregs[R1] &= ~RxINT_MASK;
731 sunzilog_maybe_update_regs(up, channel);
732}
733
734/* The port lock is held. */
735static void sunzilog_enable_ms(struct uart_port *port)
736{
737 struct uart_sunzilog_port *up =
738 container_of(port, struct uart_sunzilog_port, port);
739 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
740 unsigned char new_reg;
741
742 new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
743 if (new_reg != up->curregs[R15]) {
744 up->curregs[R15] = new_reg;
745
746 /* NOTE: Not subject to 'transmitter active' rule. */
747 write_zsreg(channel, R15, up->curregs[R15] & ~WR7pEN);
748 }
749}
750
751/* The port lock is not held. */
752static void sunzilog_break_ctl(struct uart_port *port, int break_state)
753{
754 struct uart_sunzilog_port *up =
755 container_of(port, struct uart_sunzilog_port, port);
756 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
757 unsigned char set_bits, clear_bits, new_reg;
758 unsigned long flags;
759
760 set_bits = clear_bits = 0;
761
762 if (break_state)
763 set_bits |= SND_BRK;
764 else
765 clear_bits |= SND_BRK;
766
767 uart_port_lock_irqsave(port, &flags);
768
769 new_reg = (up->curregs[R5] | set_bits) & ~clear_bits;
770 if (new_reg != up->curregs[R5]) {
771 up->curregs[R5] = new_reg;
772
773 /* NOTE: Not subject to 'transmitter active' rule. */
774 write_zsreg(channel, R5, up->curregs[R5]);
775 }
776
777 uart_port_unlock_irqrestore(port, flags);
778}
779
780static void __sunzilog_startup(struct uart_sunzilog_port *up)
781{
782 struct zilog_channel __iomem *channel;
783
784 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
785 up->prev_status = readb(&channel->control);
786
787 /* Enable receiver and transmitter. */
788 up->curregs[R3] |= RxENAB;
789 up->curregs[R5] |= TxENAB;
790
791 up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
792 sunzilog_maybe_update_regs(up, channel);
793}
794
795static int sunzilog_startup(struct uart_port *port)
796{
797 struct uart_sunzilog_port *up = UART_ZILOG(port);
798 unsigned long flags;
799
800 if (ZS_IS_CONS(up))
801 return 0;
802
803 uart_port_lock_irqsave(port, &flags);
804 __sunzilog_startup(up);
805 uart_port_unlock_irqrestore(port, flags);
806 return 0;
807}
808
809/*
810 * The test for ZS_IS_CONS is explained by the following e-mail:
811 *****
812 * From: Russell King <rmk@arm.linux.org.uk>
813 * Date: Sun, 8 Dec 2002 10:18:38 +0000
814 *
815 * On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote:
816 * > I boot my 2.5 boxes using "console=ttyS0,9600" argument,
817 * > and I noticed that something is not right with reference
818 * > counting in this case. It seems that when the console
819 * > is open by kernel initially, this is not accounted
820 * > as an open, and uart_startup is not called.
821 *
822 * That is correct. We are unable to call uart_startup when the serial
823 * console is initialised because it may need to allocate memory (as
824 * request_irq does) and the memory allocators may not have been
825 * initialised.
826 *
827 * 1. initialise the port into a state where it can send characters in the
828 * console write method.
829 *
830 * 2. don't do the actual hardware shutdown in your shutdown() method (but
831 * do the normal software shutdown - ie, free irqs etc)
832 *****
833 */
834static void sunzilog_shutdown(struct uart_port *port)
835{
836 struct uart_sunzilog_port *up = UART_ZILOG(port);
837 struct zilog_channel __iomem *channel;
838 unsigned long flags;
839
840 if (ZS_IS_CONS(up))
841 return;
842
843 uart_port_lock_irqsave(port, &flags);
844
845 channel = ZILOG_CHANNEL_FROM_PORT(port);
846
847 /* Disable receiver and transmitter. */
848 up->curregs[R3] &= ~RxENAB;
849 up->curregs[R5] &= ~TxENAB;
850
851 /* Disable all interrupts and BRK assertion. */
852 up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
853 up->curregs[R5] &= ~SND_BRK;
854 sunzilog_maybe_update_regs(up, channel);
855
856 uart_port_unlock_irqrestore(port, flags);
857}
858
859/* Shared by TTY driver and serial console setup. The port lock is held
860 * and local interrupts are disabled.
861 */
862static void
863sunzilog_convert_to_zs(struct uart_sunzilog_port *up, unsigned int cflag,
864 unsigned int iflag, int brg)
865{
866
867 up->curregs[R10] = NRZ;
868 up->curregs[R11] = TCBR | RCBR;
869
870 /* Program BAUD and clock source. */
871 up->curregs[R4] &= ~XCLK_MASK;
872 up->curregs[R4] |= X16CLK;
873 up->curregs[R12] = brg & 0xff;
874 up->curregs[R13] = (brg >> 8) & 0xff;
875 up->curregs[R14] = BRSRC | BRENAB;
876
877 /* Character size, stop bits, and parity. */
878 up->curregs[R3] &= ~RxN_MASK;
879 up->curregs[R5] &= ~TxN_MASK;
880 switch (cflag & CSIZE) {
881 case CS5:
882 up->curregs[R3] |= Rx5;
883 up->curregs[R5] |= Tx5;
884 up->parity_mask = 0x1f;
885 break;
886 case CS6:
887 up->curregs[R3] |= Rx6;
888 up->curregs[R5] |= Tx6;
889 up->parity_mask = 0x3f;
890 break;
891 case CS7:
892 up->curregs[R3] |= Rx7;
893 up->curregs[R5] |= Tx7;
894 up->parity_mask = 0x7f;
895 break;
896 case CS8:
897 default:
898 up->curregs[R3] |= Rx8;
899 up->curregs[R5] |= Tx8;
900 up->parity_mask = 0xff;
901 break;
902 }
903 up->curregs[R4] &= ~0x0c;
904 if (cflag & CSTOPB)
905 up->curregs[R4] |= SB2;
906 else
907 up->curregs[R4] |= SB1;
908 if (cflag & PARENB)
909 up->curregs[R4] |= PAR_ENAB;
910 else
911 up->curregs[R4] &= ~PAR_ENAB;
912 if (!(cflag & PARODD))
913 up->curregs[R4] |= PAR_EVEN;
914 else
915 up->curregs[R4] &= ~PAR_EVEN;
916
917 up->port.read_status_mask = Rx_OVR;
918 if (iflag & INPCK)
919 up->port.read_status_mask |= CRC_ERR | PAR_ERR;
920 if (iflag & (IGNBRK | BRKINT | PARMRK))
921 up->port.read_status_mask |= BRK_ABRT;
922
923 up->port.ignore_status_mask = 0;
924 if (iflag & IGNPAR)
925 up->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
926 if (iflag & IGNBRK) {
927 up->port.ignore_status_mask |= BRK_ABRT;
928 if (iflag & IGNPAR)
929 up->port.ignore_status_mask |= Rx_OVR;
930 }
931
932 if ((cflag & CREAD) == 0)
933 up->port.ignore_status_mask = 0xff;
934}
935
936/* The port lock is not held. */
937static void
938sunzilog_set_termios(struct uart_port *port, struct ktermios *termios,
939 const struct ktermios *old)
940{
941 struct uart_sunzilog_port *up =
942 container_of(port, struct uart_sunzilog_port, port);
943 unsigned long flags;
944 int baud, brg;
945
946 baud = uart_get_baud_rate(port, termios, old, 1200, 76800);
947
948 uart_port_lock_irqsave(&up->port, &flags);
949
950 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
951
952 sunzilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg);
953
954 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
955 up->flags |= SUNZILOG_FLAG_MODEM_STATUS;
956 else
957 up->flags &= ~SUNZILOG_FLAG_MODEM_STATUS;
958
959 up->cflag = termios->c_cflag;
960
961 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port));
962
963 uart_update_timeout(port, termios->c_cflag, baud);
964
965 uart_port_unlock_irqrestore(&up->port, flags);
966}
967
968static const char *sunzilog_type(struct uart_port *port)
969{
970 struct uart_sunzilog_port *up = UART_ZILOG(port);
971
972 return (up->flags & SUNZILOG_FLAG_ESCC) ? "zs (ESCC)" : "zs";
973}
974
975/* We do not request/release mappings of the registers here, this
976 * happens at early serial probe time.
977 */
978static void sunzilog_release_port(struct uart_port *port)
979{
980}
981
982static int sunzilog_request_port(struct uart_port *port)
983{
984 return 0;
985}
986
987/* These do not need to do anything interesting either. */
988static void sunzilog_config_port(struct uart_port *port, int flags)
989{
990}
991
992/* We do not support letting the user mess with the divisor, IRQ, etc. */
993static int sunzilog_verify_port(struct uart_port *port, struct serial_struct *ser)
994{
995 return -EINVAL;
996}
997
998#ifdef CONFIG_CONSOLE_POLL
999static int sunzilog_get_poll_char(struct uart_port *port)
1000{
1001 unsigned char ch, r1;
1002 struct uart_sunzilog_port *up =
1003 container_of(port, struct uart_sunzilog_port, port);
1004 struct zilog_channel __iomem *channel
1005 = ZILOG_CHANNEL_FROM_PORT(&up->port);
1006
1007
1008 r1 = read_zsreg(channel, R1);
1009 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
1010 writeb(ERR_RES, &channel->control);
1011 ZSDELAY();
1012 ZS_WSYNC(channel);
1013 }
1014
1015 ch = readb(&channel->control);
1016 ZSDELAY();
1017
1018 /* This funny hack depends upon BRK_ABRT not interfering
1019 * with the other bits we care about in R1.
1020 */
1021 if (ch & BRK_ABRT)
1022 r1 |= BRK_ABRT;
1023
1024 if (!(ch & Rx_CH_AV))
1025 return NO_POLL_CHAR;
1026
1027 ch = readb(&channel->data);
1028 ZSDELAY();
1029
1030 ch &= up->parity_mask;
1031 return ch;
1032}
1033
1034static void sunzilog_put_poll_char(struct uart_port *port,
1035 unsigned char ch)
1036{
1037 struct uart_sunzilog_port *up =
1038 container_of(port, struct uart_sunzilog_port, port);
1039
1040 sunzilog_putchar(&up->port, ch);
1041}
1042#endif /* CONFIG_CONSOLE_POLL */
1043
1044static const struct uart_ops sunzilog_pops = {
1045 .tx_empty = sunzilog_tx_empty,
1046 .set_mctrl = sunzilog_set_mctrl,
1047 .get_mctrl = sunzilog_get_mctrl,
1048 .stop_tx = sunzilog_stop_tx,
1049 .start_tx = sunzilog_start_tx,
1050 .stop_rx = sunzilog_stop_rx,
1051 .enable_ms = sunzilog_enable_ms,
1052 .break_ctl = sunzilog_break_ctl,
1053 .startup = sunzilog_startup,
1054 .shutdown = sunzilog_shutdown,
1055 .set_termios = sunzilog_set_termios,
1056 .type = sunzilog_type,
1057 .release_port = sunzilog_release_port,
1058 .request_port = sunzilog_request_port,
1059 .config_port = sunzilog_config_port,
1060 .verify_port = sunzilog_verify_port,
1061#ifdef CONFIG_CONSOLE_POLL
1062 .poll_get_char = sunzilog_get_poll_char,
1063 .poll_put_char = sunzilog_put_poll_char,
1064#endif
1065};
1066
1067static int uart_chip_count;
1068static struct uart_sunzilog_port *sunzilog_port_table;
1069static struct zilog_layout __iomem **sunzilog_chip_regs;
1070
1071static struct uart_sunzilog_port *sunzilog_irq_chain;
1072
1073static struct uart_driver sunzilog_reg = {
1074 .owner = THIS_MODULE,
1075 .driver_name = "sunzilog",
1076 .dev_name = "ttyS",
1077 .major = TTY_MAJOR,
1078};
1079
1080static int __init sunzilog_alloc_tables(int num_sunzilog)
1081{
1082 struct uart_sunzilog_port *up;
1083 unsigned long size;
1084 int num_channels = num_sunzilog * 2;
1085 int i;
1086
1087 size = num_channels * sizeof(struct uart_sunzilog_port);
1088 sunzilog_port_table = kzalloc(size, GFP_KERNEL);
1089 if (!sunzilog_port_table)
1090 return -ENOMEM;
1091
1092 for (i = 0; i < num_channels; i++) {
1093 up = &sunzilog_port_table[i];
1094
1095 spin_lock_init(&up->port.lock);
1096
1097 if (i == 0)
1098 sunzilog_irq_chain = up;
1099
1100 if (i < num_channels - 1)
1101 up->next = up + 1;
1102 else
1103 up->next = NULL;
1104 }
1105
1106 size = num_sunzilog * sizeof(struct zilog_layout __iomem *);
1107 sunzilog_chip_regs = kzalloc(size, GFP_KERNEL);
1108 if (!sunzilog_chip_regs) {
1109 kfree(sunzilog_port_table);
1110 sunzilog_irq_chain = NULL;
1111 return -ENOMEM;
1112 }
1113
1114 return 0;
1115}
1116
1117static void sunzilog_free_tables(void)
1118{
1119 kfree(sunzilog_port_table);
1120 sunzilog_irq_chain = NULL;
1121 kfree(sunzilog_chip_regs);
1122}
1123
1124#define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */
1125
1126static void __maybe_unused sunzilog_putchar(struct uart_port *port, unsigned char ch)
1127{
1128 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
1129 int loops = ZS_PUT_CHAR_MAX_DELAY;
1130
1131 /* This is a timed polling loop so do not switch the explicit
1132 * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM
1133 */
1134 do {
1135 unsigned char val = readb(&channel->control);
1136 if (val & Tx_BUF_EMP) {
1137 ZSDELAY();
1138 break;
1139 }
1140 udelay(5);
1141 } while (--loops);
1142
1143 writeb(ch, &channel->data);
1144 ZSDELAY();
1145 ZS_WSYNC(channel);
1146}
1147
1148#ifdef CONFIG_SERIO
1149
1150static DEFINE_SPINLOCK(sunzilog_serio_lock);
1151
1152static int sunzilog_serio_write(struct serio *serio, unsigned char ch)
1153{
1154 struct uart_sunzilog_port *up = serio->port_data;
1155 unsigned long flags;
1156
1157 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1158
1159 sunzilog_putchar(&up->port, ch);
1160
1161 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1162
1163 return 0;
1164}
1165
1166static int sunzilog_serio_open(struct serio *serio)
1167{
1168 struct uart_sunzilog_port *up = serio->port_data;
1169 unsigned long flags;
1170 int ret;
1171
1172 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1173 if (!up->serio_open) {
1174 up->serio_open = 1;
1175 ret = 0;
1176 } else
1177 ret = -EBUSY;
1178 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1179
1180 return ret;
1181}
1182
1183static void sunzilog_serio_close(struct serio *serio)
1184{
1185 struct uart_sunzilog_port *up = serio->port_data;
1186 unsigned long flags;
1187
1188 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1189 up->serio_open = 0;
1190 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1191}
1192
1193#endif /* CONFIG_SERIO */
1194
1195#ifdef CONFIG_SERIAL_SUNZILOG_CONSOLE
1196static void
1197sunzilog_console_write(struct console *con, const char *s, unsigned int count)
1198{
1199 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index];
1200 unsigned long flags;
1201 int locked = 1;
1202
1203 if (up->port.sysrq || oops_in_progress)
1204 locked = uart_port_trylock_irqsave(&up->port, &flags);
1205 else
1206 uart_port_lock_irqsave(&up->port, &flags);
1207
1208 uart_console_write(&up->port, s, count, sunzilog_putchar);
1209 udelay(2);
1210
1211 if (locked)
1212 uart_port_unlock_irqrestore(&up->port, flags);
1213}
1214
1215static int __init sunzilog_console_setup(struct console *con, char *options)
1216{
1217 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index];
1218 unsigned long flags;
1219 int baud, brg;
1220
1221 if (up->port.type != PORT_SUNZILOG)
1222 return -EINVAL;
1223
1224 printk(KERN_INFO "Console: ttyS%d (SunZilog zs%d)\n",
1225 (sunzilog_reg.minor - 64) + con->index, con->index);
1226
1227 /* Get firmware console settings. */
1228 sunserial_console_termios(con, up->port.dev->of_node);
1229
1230 /* Firmware console speed is limited to 150-->38400 baud so
1231 * this hackish cflag thing is OK.
1232 */
1233 switch (con->cflag & CBAUD) {
1234 case B150: baud = 150; break;
1235 case B300: baud = 300; break;
1236 case B600: baud = 600; break;
1237 case B1200: baud = 1200; break;
1238 case B2400: baud = 2400; break;
1239 case B4800: baud = 4800; break;
1240 default: case B9600: baud = 9600; break;
1241 case B19200: baud = 19200; break;
1242 case B38400: baud = 38400; break;
1243 }
1244
1245 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1246
1247 uart_port_lock_irqsave(&up->port, &flags);
1248
1249 up->curregs[R15] |= BRKIE;
1250 sunzilog_convert_to_zs(up, con->cflag, 0, brg);
1251
1252 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS);
1253 __sunzilog_startup(up);
1254
1255 uart_port_unlock_irqrestore(&up->port, flags);
1256
1257 return 0;
1258}
1259
1260static struct console sunzilog_console_ops = {
1261 .name = "ttyS",
1262 .write = sunzilog_console_write,
1263 .device = uart_console_device,
1264 .setup = sunzilog_console_setup,
1265 .flags = CON_PRINTBUFFER,
1266 .index = -1,
1267 .data = &sunzilog_reg,
1268};
1269
1270static inline struct console *SUNZILOG_CONSOLE(void)
1271{
1272 return &sunzilog_console_ops;
1273}
1274
1275#else
1276#define SUNZILOG_CONSOLE() (NULL)
1277#endif
1278
1279static void sunzilog_init_kbdms(struct uart_sunzilog_port *up)
1280{
1281 int baud, brg;
1282
1283 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) {
1284 up->cflag = B1200 | CS8 | CLOCAL | CREAD;
1285 baud = 1200;
1286 } else {
1287 up->cflag = B4800 | CS8 | CLOCAL | CREAD;
1288 baud = 4800;
1289 }
1290
1291 up->curregs[R15] |= BRKIE;
1292 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1293 sunzilog_convert_to_zs(up, up->cflag, 0, brg);
1294 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS);
1295 __sunzilog_startup(up);
1296}
1297
1298#ifdef CONFIG_SERIO
1299static void sunzilog_register_serio(struct uart_sunzilog_port *up)
1300{
1301 struct serio *serio = &up->serio;
1302
1303 serio->port_data = up;
1304
1305 serio->id.type = SERIO_RS232;
1306 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) {
1307 serio->id.proto = SERIO_SUNKBD;
1308 strscpy(serio->name, "zskbd", sizeof(serio->name));
1309 } else {
1310 serio->id.proto = SERIO_SUN;
1311 serio->id.extra = 1;
1312 strscpy(serio->name, "zsms", sizeof(serio->name));
1313 }
1314 strscpy(serio->phys,
1315 ((up->flags & SUNZILOG_FLAG_CONS_KEYB) ?
1316 "zs/serio0" : "zs/serio1"),
1317 sizeof(serio->phys));
1318
1319 serio->write = sunzilog_serio_write;
1320 serio->open = sunzilog_serio_open;
1321 serio->close = sunzilog_serio_close;
1322 serio->dev.parent = up->port.dev;
1323
1324 serio_register_port(serio);
1325}
1326#endif
1327
1328static void sunzilog_init_hw(struct uart_sunzilog_port *up)
1329{
1330 struct zilog_channel __iomem *channel;
1331 unsigned long flags;
1332 int baud, brg;
1333
1334 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1335
1336 uart_port_lock_irqsave(&up->port, &flags);
1337 if (ZS_IS_CHANNEL_A(up)) {
1338 write_zsreg(channel, R9, FHWRES);
1339 ZSDELAY_LONG();
1340 (void) read_zsreg(channel, R0);
1341 }
1342
1343 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB |
1344 SUNZILOG_FLAG_CONS_MOUSE)) {
1345 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1346 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1347 up->curregs[R3] = RxENAB | Rx8;
1348 up->curregs[R5] = TxENAB | Tx8;
1349 up->curregs[R6] = 0x00; /* SDLC Address */
1350 up->curregs[R7] = 0x7E; /* SDLC Flag */
1351 up->curregs[R9] = NV;
1352 up->curregs[R7p] = 0x00;
1353 sunzilog_init_kbdms(up);
1354 /* Only enable interrupts if an ISR handler available */
1355 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER)
1356 up->curregs[R9] |= MIE;
1357 write_zsreg(channel, R9, up->curregs[R9]);
1358 } else {
1359 /* Normal serial TTY. */
1360 up->parity_mask = 0xff;
1361 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1362 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1363 up->curregs[R3] = RxENAB | Rx8;
1364 up->curregs[R5] = TxENAB | Tx8;
1365 up->curregs[R6] = 0x00; /* SDLC Address */
1366 up->curregs[R7] = 0x7E; /* SDLC Flag */
1367 up->curregs[R9] = NV;
1368 up->curregs[R10] = NRZ;
1369 up->curregs[R11] = TCBR | RCBR;
1370 baud = 9600;
1371 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1372 up->curregs[R12] = (brg & 0xff);
1373 up->curregs[R13] = (brg >> 8) & 0xff;
1374 up->curregs[R14] = BRSRC | BRENAB;
1375 up->curregs[R15] = FIFOEN; /* Use FIFO if on ESCC */
1376 up->curregs[R7p] = TxFIFO_LVL | RxFIFO_LVL;
1377 if (__load_zsregs(channel, up->curregs)) {
1378 up->flags |= SUNZILOG_FLAG_ESCC;
1379 }
1380 /* Only enable interrupts if an ISR handler available */
1381 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER)
1382 up->curregs[R9] |= MIE;
1383 write_zsreg(channel, R9, up->curregs[R9]);
1384 }
1385
1386 uart_port_unlock_irqrestore(&up->port, flags);
1387
1388#ifdef CONFIG_SERIO
1389 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB |
1390 SUNZILOG_FLAG_CONS_MOUSE))
1391 sunzilog_register_serio(up);
1392#endif
1393}
1394
1395static int zilog_irq;
1396
1397static int zs_probe(struct platform_device *op)
1398{
1399 static int kbm_inst, uart_inst;
1400 int inst;
1401 struct uart_sunzilog_port *up;
1402 struct zilog_layout __iomem *rp;
1403 int keyboard_mouse = 0;
1404 int err;
1405
1406 if (of_property_present(op->dev.of_node, "keyboard"))
1407 keyboard_mouse = 1;
1408
1409 /* uarts must come before keyboards/mice */
1410 if (keyboard_mouse)
1411 inst = uart_chip_count + kbm_inst;
1412 else
1413 inst = uart_inst;
1414
1415 sunzilog_chip_regs[inst] = of_ioremap(&op->resource[0], 0,
1416 sizeof(struct zilog_layout),
1417 "zs");
1418 if (!sunzilog_chip_regs[inst])
1419 return -ENOMEM;
1420
1421 rp = sunzilog_chip_regs[inst];
1422
1423 if (!zilog_irq)
1424 zilog_irq = op->archdata.irqs[0];
1425
1426 up = &sunzilog_port_table[inst * 2];
1427
1428 /* Channel A */
1429 up[0].port.mapbase = op->resource[0].start + 0x00;
1430 up[0].port.membase = (void __iomem *) &rp->channelA;
1431 up[0].port.iotype = UPIO_MEM;
1432 up[0].port.irq = op->archdata.irqs[0];
1433 up[0].port.uartclk = ZS_CLOCK;
1434 up[0].port.fifosize = 1;
1435 up[0].port.ops = &sunzilog_pops;
1436 up[0].port.type = PORT_SUNZILOG;
1437 up[0].port.flags = 0;
1438 up[0].port.line = (inst * 2) + 0;
1439 up[0].port.dev = &op->dev;
1440 up[0].flags |= SUNZILOG_FLAG_IS_CHANNEL_A;
1441 up[0].port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_SUNZILOG_CONSOLE);
1442 if (keyboard_mouse)
1443 up[0].flags |= SUNZILOG_FLAG_CONS_KEYB;
1444 sunzilog_init_hw(&up[0]);
1445
1446 /* Channel B */
1447 up[1].port.mapbase = op->resource[0].start + 0x04;
1448 up[1].port.membase = (void __iomem *) &rp->channelB;
1449 up[1].port.iotype = UPIO_MEM;
1450 up[1].port.irq = op->archdata.irqs[0];
1451 up[1].port.uartclk = ZS_CLOCK;
1452 up[1].port.fifosize = 1;
1453 up[1].port.ops = &sunzilog_pops;
1454 up[1].port.type = PORT_SUNZILOG;
1455 up[1].port.flags = 0;
1456 up[1].port.line = (inst * 2) + 1;
1457 up[1].port.dev = &op->dev;
1458 up[1].flags |= 0;
1459 up[1].port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_SUNZILOG_CONSOLE);
1460 if (keyboard_mouse)
1461 up[1].flags |= SUNZILOG_FLAG_CONS_MOUSE;
1462 sunzilog_init_hw(&up[1]);
1463
1464 if (!keyboard_mouse) {
1465 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node,
1466 &sunzilog_reg, up[0].port.line,
1467 false))
1468 up->flags |= SUNZILOG_FLAG_IS_CONS;
1469 err = uart_add_one_port(&sunzilog_reg, &up[0].port);
1470 if (err) {
1471 of_iounmap(&op->resource[0],
1472 rp, sizeof(struct zilog_layout));
1473 return err;
1474 }
1475 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node,
1476 &sunzilog_reg, up[1].port.line,
1477 false))
1478 up->flags |= SUNZILOG_FLAG_IS_CONS;
1479 err = uart_add_one_port(&sunzilog_reg, &up[1].port);
1480 if (err) {
1481 uart_remove_one_port(&sunzilog_reg, &up[0].port);
1482 of_iounmap(&op->resource[0],
1483 rp, sizeof(struct zilog_layout));
1484 return err;
1485 }
1486 uart_inst++;
1487 } else {
1488 printk(KERN_INFO "%s: Keyboard at MMIO 0x%llx (irq = %d) "
1489 "is a %s\n",
1490 dev_name(&op->dev),
1491 (unsigned long long) up[0].port.mapbase,
1492 op->archdata.irqs[0], sunzilog_type(&up[0].port));
1493 printk(KERN_INFO "%s: Mouse at MMIO 0x%llx (irq = %d) "
1494 "is a %s\n",
1495 dev_name(&op->dev),
1496 (unsigned long long) up[1].port.mapbase,
1497 op->archdata.irqs[0], sunzilog_type(&up[1].port));
1498 kbm_inst++;
1499 }
1500
1501 platform_set_drvdata(op, &up[0]);
1502
1503 return 0;
1504}
1505
1506static void zs_remove_one(struct uart_sunzilog_port *up)
1507{
1508 if (ZS_IS_KEYB(up) || ZS_IS_MOUSE(up)) {
1509#ifdef CONFIG_SERIO
1510 serio_unregister_port(&up->serio);
1511#endif
1512 } else
1513 uart_remove_one_port(&sunzilog_reg, &up->port);
1514}
1515
1516static void zs_remove(struct platform_device *op)
1517{
1518 struct uart_sunzilog_port *up = platform_get_drvdata(op);
1519 struct zilog_layout __iomem *regs;
1520
1521 zs_remove_one(&up[0]);
1522 zs_remove_one(&up[1]);
1523
1524 regs = sunzilog_chip_regs[up[0].port.line / 2];
1525 of_iounmap(&op->resource[0], regs, sizeof(struct zilog_layout));
1526}
1527
1528static const struct of_device_id zs_match[] = {
1529 {
1530 .name = "zs",
1531 },
1532 {},
1533};
1534MODULE_DEVICE_TABLE(of, zs_match);
1535
1536static struct platform_driver zs_driver = {
1537 .driver = {
1538 .name = "zs",
1539 .of_match_table = zs_match,
1540 },
1541 .probe = zs_probe,
1542 .remove_new = zs_remove,
1543};
1544
1545static int __init sunzilog_init(void)
1546{
1547 struct device_node *dp;
1548 int err;
1549 int num_keybms = 0;
1550 int num_sunzilog = 0;
1551
1552 for_each_node_by_name(dp, "zs") {
1553 num_sunzilog++;
1554 if (of_property_present(dp, "keyboard"))
1555 num_keybms++;
1556 }
1557
1558 if (num_sunzilog) {
1559 err = sunzilog_alloc_tables(num_sunzilog);
1560 if (err)
1561 goto out;
1562
1563 uart_chip_count = num_sunzilog - num_keybms;
1564
1565 err = sunserial_register_minors(&sunzilog_reg,
1566 uart_chip_count * 2);
1567 if (err)
1568 goto out_free_tables;
1569 }
1570
1571 err = platform_driver_register(&zs_driver);
1572 if (err)
1573 goto out_unregister_uart;
1574
1575 if (zilog_irq) {
1576 struct uart_sunzilog_port *up = sunzilog_irq_chain;
1577 err = request_irq(zilog_irq, sunzilog_interrupt, IRQF_SHARED,
1578 "zs", sunzilog_irq_chain);
1579 if (err)
1580 goto out_unregister_driver;
1581
1582 /* Enable Interrupts */
1583 while (up) {
1584 struct zilog_channel __iomem *channel;
1585
1586 /* printk (KERN_INFO "Enable IRQ for ZILOG Hardware %p\n", up); */
1587 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1588 up->flags |= SUNZILOG_FLAG_ISR_HANDLER;
1589 up->curregs[R9] |= MIE;
1590 write_zsreg(channel, R9, up->curregs[R9]);
1591 up = up->next;
1592 }
1593 }
1594
1595out:
1596 return err;
1597
1598out_unregister_driver:
1599 platform_driver_unregister(&zs_driver);
1600
1601out_unregister_uart:
1602 if (num_sunzilog) {
1603 sunserial_unregister_minors(&sunzilog_reg, num_sunzilog);
1604 sunzilog_reg.cons = NULL;
1605 }
1606
1607out_free_tables:
1608 sunzilog_free_tables();
1609 goto out;
1610}
1611
1612static void __exit sunzilog_exit(void)
1613{
1614 platform_driver_unregister(&zs_driver);
1615
1616 if (zilog_irq) {
1617 struct uart_sunzilog_port *up = sunzilog_irq_chain;
1618
1619 /* Disable Interrupts */
1620 while (up) {
1621 struct zilog_channel __iomem *channel;
1622
1623 /* printk (KERN_INFO "Disable IRQ for ZILOG Hardware %p\n", up); */
1624 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1625 up->flags &= ~SUNZILOG_FLAG_ISR_HANDLER;
1626 up->curregs[R9] &= ~MIE;
1627 write_zsreg(channel, R9, up->curregs[R9]);
1628 up = up->next;
1629 }
1630
1631 free_irq(zilog_irq, sunzilog_irq_chain);
1632 zilog_irq = 0;
1633 }
1634
1635 if (sunzilog_reg.nr) {
1636 sunserial_unregister_minors(&sunzilog_reg, sunzilog_reg.nr);
1637 sunzilog_free_tables();
1638 }
1639}
1640
1641module_init(sunzilog_init);
1642module_exit(sunzilog_exit);
1643
1644MODULE_AUTHOR("David S. Miller");
1645MODULE_DESCRIPTION("Sun Zilog serial port driver");
1646MODULE_VERSION("2.0");
1647MODULE_LICENSE("GPL");
1/* sunzilog.c: Zilog serial driver for Sparc systems.
2 *
3 * Driver for Zilog serial chips found on Sun workstations and
4 * servers. This driver could actually be made more generic.
5 *
6 * This is based on the old drivers/sbus/char/zs.c code. A lot
7 * of code has been simply moved over directly from there but
8 * much has been rewritten. Credits therefore go out to Eddie
9 * C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell for their
10 * work there.
11 *
12 * Copyright (C) 2002, 2006, 2007 David S. Miller (davem@davemloft.net)
13 */
14
15#include <linux/module.h>
16#include <linux/kernel.h>
17#include <linux/errno.h>
18#include <linux/delay.h>
19#include <linux/tty.h>
20#include <linux/tty_flip.h>
21#include <linux/major.h>
22#include <linux/string.h>
23#include <linux/ptrace.h>
24#include <linux/ioport.h>
25#include <linux/slab.h>
26#include <linux/circ_buf.h>
27#include <linux/serial.h>
28#include <linux/sysrq.h>
29#include <linux/console.h>
30#include <linux/spinlock.h>
31#ifdef CONFIG_SERIO
32#include <linux/serio.h>
33#endif
34#include <linux/init.h>
35#include <linux/of_device.h>
36
37#include <asm/io.h>
38#include <asm/irq.h>
39#include <asm/prom.h>
40#include <asm/setup.h>
41
42#if defined(CONFIG_SERIAL_SUNZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
43#define SUPPORT_SYSRQ
44#endif
45
46#include <linux/serial_core.h>
47#include <linux/sunserialcore.h>
48
49#include "sunzilog.h"
50
51/* On 32-bit sparcs we need to delay after register accesses
52 * to accommodate sun4 systems, but we do not need to flush writes.
53 * On 64-bit sparc we only need to flush single writes to ensure
54 * completion.
55 */
56#ifndef CONFIG_SPARC64
57#define ZSDELAY() udelay(5)
58#define ZSDELAY_LONG() udelay(20)
59#define ZS_WSYNC(channel) do { } while (0)
60#else
61#define ZSDELAY()
62#define ZSDELAY_LONG()
63#define ZS_WSYNC(__channel) \
64 readb(&((__channel)->control))
65#endif
66
67#define ZS_CLOCK 4915200 /* Zilog input clock rate. */
68#define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */
69
70/*
71 * We wrap our port structure around the generic uart_port.
72 */
73struct uart_sunzilog_port {
74 struct uart_port port;
75
76 /* IRQ servicing chain. */
77 struct uart_sunzilog_port *next;
78
79 /* Current values of Zilog write registers. */
80 unsigned char curregs[NUM_ZSREGS];
81
82 unsigned int flags;
83#define SUNZILOG_FLAG_CONS_KEYB 0x00000001
84#define SUNZILOG_FLAG_CONS_MOUSE 0x00000002
85#define SUNZILOG_FLAG_IS_CONS 0x00000004
86#define SUNZILOG_FLAG_IS_KGDB 0x00000008
87#define SUNZILOG_FLAG_MODEM_STATUS 0x00000010
88#define SUNZILOG_FLAG_IS_CHANNEL_A 0x00000020
89#define SUNZILOG_FLAG_REGS_HELD 0x00000040
90#define SUNZILOG_FLAG_TX_STOPPED 0x00000080
91#define SUNZILOG_FLAG_TX_ACTIVE 0x00000100
92#define SUNZILOG_FLAG_ESCC 0x00000200
93#define SUNZILOG_FLAG_ISR_HANDLER 0x00000400
94
95 unsigned int cflag;
96
97 unsigned char parity_mask;
98 unsigned char prev_status;
99
100#ifdef CONFIG_SERIO
101 struct serio serio;
102 int serio_open;
103#endif
104};
105
106static void sunzilog_putchar(struct uart_port *port, int ch);
107
108#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel __iomem *)((PORT)->membase))
109#define UART_ZILOG(PORT) ((struct uart_sunzilog_port *)(PORT))
110
111#define ZS_IS_KEYB(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_KEYB)
112#define ZS_IS_MOUSE(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_MOUSE)
113#define ZS_IS_CONS(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CONS)
114#define ZS_IS_KGDB(UP) ((UP)->flags & SUNZILOG_FLAG_IS_KGDB)
115#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & SUNZILOG_FLAG_MODEM_STATUS)
116#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CHANNEL_A)
117#define ZS_REGS_HELD(UP) ((UP)->flags & SUNZILOG_FLAG_REGS_HELD)
118#define ZS_TX_STOPPED(UP) ((UP)->flags & SUNZILOG_FLAG_TX_STOPPED)
119#define ZS_TX_ACTIVE(UP) ((UP)->flags & SUNZILOG_FLAG_TX_ACTIVE)
120
121/* Reading and writing Zilog8530 registers. The delays are to make this
122 * driver work on the Sun4 which needs a settling delay after each chip
123 * register access, other machines handle this in hardware via auxiliary
124 * flip-flops which implement the settle time we do in software.
125 *
126 * The port lock must be held and local IRQs must be disabled
127 * when {read,write}_zsreg is invoked.
128 */
129static unsigned char read_zsreg(struct zilog_channel __iomem *channel,
130 unsigned char reg)
131{
132 unsigned char retval;
133
134 writeb(reg, &channel->control);
135 ZSDELAY();
136 retval = readb(&channel->control);
137 ZSDELAY();
138
139 return retval;
140}
141
142static void write_zsreg(struct zilog_channel __iomem *channel,
143 unsigned char reg, unsigned char value)
144{
145 writeb(reg, &channel->control);
146 ZSDELAY();
147 writeb(value, &channel->control);
148 ZSDELAY();
149}
150
151static void sunzilog_clear_fifo(struct zilog_channel __iomem *channel)
152{
153 int i;
154
155 for (i = 0; i < 32; i++) {
156 unsigned char regval;
157
158 regval = readb(&channel->control);
159 ZSDELAY();
160 if (regval & Rx_CH_AV)
161 break;
162
163 regval = read_zsreg(channel, R1);
164 readb(&channel->data);
165 ZSDELAY();
166
167 if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) {
168 writeb(ERR_RES, &channel->control);
169 ZSDELAY();
170 ZS_WSYNC(channel);
171 }
172 }
173}
174
175/* This function must only be called when the TX is not busy. The UART
176 * port lock must be held and local interrupts disabled.
177 */
178static int __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *regs)
179{
180 int i;
181 int escc;
182 unsigned char r15;
183
184 /* Let pending transmits finish. */
185 for (i = 0; i < 1000; i++) {
186 unsigned char stat = read_zsreg(channel, R1);
187 if (stat & ALL_SNT)
188 break;
189 udelay(100);
190 }
191
192 writeb(ERR_RES, &channel->control);
193 ZSDELAY();
194 ZS_WSYNC(channel);
195
196 sunzilog_clear_fifo(channel);
197
198 /* Disable all interrupts. */
199 write_zsreg(channel, R1,
200 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
201
202 /* Set parity, sync config, stop bits, and clock divisor. */
203 write_zsreg(channel, R4, regs[R4]);
204
205 /* Set misc. TX/RX control bits. */
206 write_zsreg(channel, R10, regs[R10]);
207
208 /* Set TX/RX controls sans the enable bits. */
209 write_zsreg(channel, R3, regs[R3] & ~RxENAB);
210 write_zsreg(channel, R5, regs[R5] & ~TxENAB);
211
212 /* Synchronous mode config. */
213 write_zsreg(channel, R6, regs[R6]);
214 write_zsreg(channel, R7, regs[R7]);
215
216 /* Don't mess with the interrupt vector (R2, unused by us) and
217 * master interrupt control (R9). We make sure this is setup
218 * properly at probe time then never touch it again.
219 */
220
221 /* Disable baud generator. */
222 write_zsreg(channel, R14, regs[R14] & ~BRENAB);
223
224 /* Clock mode control. */
225 write_zsreg(channel, R11, regs[R11]);
226
227 /* Lower and upper byte of baud rate generator divisor. */
228 write_zsreg(channel, R12, regs[R12]);
229 write_zsreg(channel, R13, regs[R13]);
230
231 /* Now rewrite R14, with BRENAB (if set). */
232 write_zsreg(channel, R14, regs[R14]);
233
234 /* External status interrupt control. */
235 write_zsreg(channel, R15, (regs[R15] | WR7pEN) & ~FIFOEN);
236
237 /* ESCC Extension Register */
238 r15 = read_zsreg(channel, R15);
239 if (r15 & 0x01) {
240 write_zsreg(channel, R7, regs[R7p]);
241
242 /* External status interrupt and FIFO control. */
243 write_zsreg(channel, R15, regs[R15] & ~WR7pEN);
244 escc = 1;
245 } else {
246 /* Clear FIFO bit case it is an issue */
247 regs[R15] &= ~FIFOEN;
248 escc = 0;
249 }
250
251 /* Reset external status interrupts. */
252 write_zsreg(channel, R0, RES_EXT_INT); /* First Latch */
253 write_zsreg(channel, R0, RES_EXT_INT); /* Second Latch */
254
255 /* Rewrite R3/R5, this time without enables masked. */
256 write_zsreg(channel, R3, regs[R3]);
257 write_zsreg(channel, R5, regs[R5]);
258
259 /* Rewrite R1, this time without IRQ enabled masked. */
260 write_zsreg(channel, R1, regs[R1]);
261
262 return escc;
263}
264
265/* Reprogram the Zilog channel HW registers with the copies found in the
266 * software state struct. If the transmitter is busy, we defer this update
267 * until the next TX complete interrupt. Else, we do it right now.
268 *
269 * The UART port lock must be held and local interrupts disabled.
270 */
271static void sunzilog_maybe_update_regs(struct uart_sunzilog_port *up,
272 struct zilog_channel __iomem *channel)
273{
274 if (!ZS_REGS_HELD(up)) {
275 if (ZS_TX_ACTIVE(up)) {
276 up->flags |= SUNZILOG_FLAG_REGS_HELD;
277 } else {
278 __load_zsregs(channel, up->curregs);
279 }
280 }
281}
282
283static void sunzilog_change_mouse_baud(struct uart_sunzilog_port *up)
284{
285 unsigned int cur_cflag = up->cflag;
286 int brg, new_baud;
287
288 up->cflag &= ~CBAUD;
289 up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud);
290
291 brg = BPS_TO_BRG(new_baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
292 up->curregs[R12] = (brg & 0xff);
293 up->curregs[R13] = (brg >> 8) & 0xff;
294 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(&up->port));
295}
296
297static void sunzilog_kbdms_receive_chars(struct uart_sunzilog_port *up,
298 unsigned char ch, int is_break)
299{
300 if (ZS_IS_KEYB(up)) {
301 /* Stop-A is handled by drivers/char/keyboard.c now. */
302#ifdef CONFIG_SERIO
303 if (up->serio_open)
304 serio_interrupt(&up->serio, ch, 0);
305#endif
306 } else if (ZS_IS_MOUSE(up)) {
307 int ret = suncore_mouse_baud_detection(ch, is_break);
308
309 switch (ret) {
310 case 2:
311 sunzilog_change_mouse_baud(up);
312 /* fallthru */
313 case 1:
314 break;
315
316 case 0:
317#ifdef CONFIG_SERIO
318 if (up->serio_open)
319 serio_interrupt(&up->serio, ch, 0);
320#endif
321 break;
322 }
323 }
324}
325
326static struct tty_port *
327sunzilog_receive_chars(struct uart_sunzilog_port *up,
328 struct zilog_channel __iomem *channel)
329{
330 struct tty_port *port = NULL;
331 unsigned char ch, r1, flag;
332
333 if (up->port.state != NULL) /* Unopened serial console */
334 port = &up->port.state->port;
335
336 for (;;) {
337
338 r1 = read_zsreg(channel, R1);
339 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
340 writeb(ERR_RES, &channel->control);
341 ZSDELAY();
342 ZS_WSYNC(channel);
343 }
344
345 ch = readb(&channel->control);
346 ZSDELAY();
347
348 /* This funny hack depends upon BRK_ABRT not interfering
349 * with the other bits we care about in R1.
350 */
351 if (ch & BRK_ABRT)
352 r1 |= BRK_ABRT;
353
354 if (!(ch & Rx_CH_AV))
355 break;
356
357 ch = readb(&channel->data);
358 ZSDELAY();
359
360 ch &= up->parity_mask;
361
362 if (unlikely(ZS_IS_KEYB(up)) || unlikely(ZS_IS_MOUSE(up))) {
363 sunzilog_kbdms_receive_chars(up, ch, 0);
364 continue;
365 }
366
367 /* A real serial line, record the character and status. */
368 flag = TTY_NORMAL;
369 up->port.icount.rx++;
370 if (r1 & (BRK_ABRT | PAR_ERR | Rx_OVR | CRC_ERR)) {
371 if (r1 & BRK_ABRT) {
372 r1 &= ~(PAR_ERR | CRC_ERR);
373 up->port.icount.brk++;
374 if (uart_handle_break(&up->port))
375 continue;
376 }
377 else if (r1 & PAR_ERR)
378 up->port.icount.parity++;
379 else if (r1 & CRC_ERR)
380 up->port.icount.frame++;
381 if (r1 & Rx_OVR)
382 up->port.icount.overrun++;
383 r1 &= up->port.read_status_mask;
384 if (r1 & BRK_ABRT)
385 flag = TTY_BREAK;
386 else if (r1 & PAR_ERR)
387 flag = TTY_PARITY;
388 else if (r1 & CRC_ERR)
389 flag = TTY_FRAME;
390 }
391 if (uart_handle_sysrq_char(&up->port, ch) || !port)
392 continue;
393
394 if (up->port.ignore_status_mask == 0xff ||
395 (r1 & up->port.ignore_status_mask) == 0) {
396 tty_insert_flip_char(port, ch, flag);
397 }
398 if (r1 & Rx_OVR)
399 tty_insert_flip_char(port, 0, TTY_OVERRUN);
400 }
401
402 return port;
403}
404
405static void sunzilog_status_handle(struct uart_sunzilog_port *up,
406 struct zilog_channel __iomem *channel)
407{
408 unsigned char status;
409
410 status = readb(&channel->control);
411 ZSDELAY();
412
413 writeb(RES_EXT_INT, &channel->control);
414 ZSDELAY();
415 ZS_WSYNC(channel);
416
417 if (status & BRK_ABRT) {
418 if (ZS_IS_MOUSE(up))
419 sunzilog_kbdms_receive_chars(up, 0, 1);
420 if (ZS_IS_CONS(up)) {
421 /* Wait for BREAK to deassert to avoid potentially
422 * confusing the PROM.
423 */
424 while (1) {
425 status = readb(&channel->control);
426 ZSDELAY();
427 if (!(status & BRK_ABRT))
428 break;
429 }
430 sun_do_break();
431 return;
432 }
433 }
434
435 if (ZS_WANTS_MODEM_STATUS(up)) {
436 if (status & SYNC)
437 up->port.icount.dsr++;
438
439 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
440 * But it does not tell us which bit has changed, we have to keep
441 * track of this ourselves.
442 */
443 if ((status ^ up->prev_status) ^ DCD)
444 uart_handle_dcd_change(&up->port,
445 (status & DCD));
446 if ((status ^ up->prev_status) ^ CTS)
447 uart_handle_cts_change(&up->port,
448 (status & CTS));
449
450 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
451 }
452
453 up->prev_status = status;
454}
455
456static void sunzilog_transmit_chars(struct uart_sunzilog_port *up,
457 struct zilog_channel __iomem *channel)
458{
459 struct circ_buf *xmit;
460
461 if (ZS_IS_CONS(up)) {
462 unsigned char status = readb(&channel->control);
463 ZSDELAY();
464
465 /* TX still busy? Just wait for the next TX done interrupt.
466 *
467 * It can occur because of how we do serial console writes. It would
468 * be nice to transmit console writes just like we normally would for
469 * a TTY line. (ie. buffered and TX interrupt driven). That is not
470 * easy because console writes cannot sleep. One solution might be
471 * to poll on enough port->xmit space becoming free. -DaveM
472 */
473 if (!(status & Tx_BUF_EMP))
474 return;
475 }
476
477 up->flags &= ~SUNZILOG_FLAG_TX_ACTIVE;
478
479 if (ZS_REGS_HELD(up)) {
480 __load_zsregs(channel, up->curregs);
481 up->flags &= ~SUNZILOG_FLAG_REGS_HELD;
482 }
483
484 if (ZS_TX_STOPPED(up)) {
485 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED;
486 goto ack_tx_int;
487 }
488
489 if (up->port.x_char) {
490 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
491 writeb(up->port.x_char, &channel->data);
492 ZSDELAY();
493 ZS_WSYNC(channel);
494
495 up->port.icount.tx++;
496 up->port.x_char = 0;
497 return;
498 }
499
500 if (up->port.state == NULL)
501 goto ack_tx_int;
502 xmit = &up->port.state->xmit;
503 if (uart_circ_empty(xmit))
504 goto ack_tx_int;
505
506 if (uart_tx_stopped(&up->port))
507 goto ack_tx_int;
508
509 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
510 writeb(xmit->buf[xmit->tail], &channel->data);
511 ZSDELAY();
512 ZS_WSYNC(channel);
513
514 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
515 up->port.icount.tx++;
516
517 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
518 uart_write_wakeup(&up->port);
519
520 return;
521
522ack_tx_int:
523 writeb(RES_Tx_P, &channel->control);
524 ZSDELAY();
525 ZS_WSYNC(channel);
526}
527
528static irqreturn_t sunzilog_interrupt(int irq, void *dev_id)
529{
530 struct uart_sunzilog_port *up = dev_id;
531
532 while (up) {
533 struct zilog_channel __iomem *channel
534 = ZILOG_CHANNEL_FROM_PORT(&up->port);
535 struct tty_port *port;
536 unsigned char r3;
537
538 spin_lock(&up->port.lock);
539 r3 = read_zsreg(channel, R3);
540
541 /* Channel A */
542 port = NULL;
543 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
544 writeb(RES_H_IUS, &channel->control);
545 ZSDELAY();
546 ZS_WSYNC(channel);
547
548 if (r3 & CHARxIP)
549 port = sunzilog_receive_chars(up, channel);
550 if (r3 & CHAEXT)
551 sunzilog_status_handle(up, channel);
552 if (r3 & CHATxIP)
553 sunzilog_transmit_chars(up, channel);
554 }
555 spin_unlock(&up->port.lock);
556
557 if (port)
558 tty_flip_buffer_push(port);
559
560 /* Channel B */
561 up = up->next;
562 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
563
564 spin_lock(&up->port.lock);
565 port = NULL;
566 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
567 writeb(RES_H_IUS, &channel->control);
568 ZSDELAY();
569 ZS_WSYNC(channel);
570
571 if (r3 & CHBRxIP)
572 port = sunzilog_receive_chars(up, channel);
573 if (r3 & CHBEXT)
574 sunzilog_status_handle(up, channel);
575 if (r3 & CHBTxIP)
576 sunzilog_transmit_chars(up, channel);
577 }
578 spin_unlock(&up->port.lock);
579
580 if (port)
581 tty_flip_buffer_push(port);
582
583 up = up->next;
584 }
585
586 return IRQ_HANDLED;
587}
588
589/* A convenient way to quickly get R0 status. The caller must _not_ hold the
590 * port lock, it is acquired here.
591 */
592static __inline__ unsigned char sunzilog_read_channel_status(struct uart_port *port)
593{
594 struct zilog_channel __iomem *channel;
595 unsigned char status;
596
597 channel = ZILOG_CHANNEL_FROM_PORT(port);
598 status = readb(&channel->control);
599 ZSDELAY();
600
601 return status;
602}
603
604/* The port lock is not held. */
605static unsigned int sunzilog_tx_empty(struct uart_port *port)
606{
607 unsigned long flags;
608 unsigned char status;
609 unsigned int ret;
610
611 spin_lock_irqsave(&port->lock, flags);
612
613 status = sunzilog_read_channel_status(port);
614
615 spin_unlock_irqrestore(&port->lock, flags);
616
617 if (status & Tx_BUF_EMP)
618 ret = TIOCSER_TEMT;
619 else
620 ret = 0;
621
622 return ret;
623}
624
625/* The port lock is held and interrupts are disabled. */
626static unsigned int sunzilog_get_mctrl(struct uart_port *port)
627{
628 unsigned char status;
629 unsigned int ret;
630
631 status = sunzilog_read_channel_status(port);
632
633 ret = 0;
634 if (status & DCD)
635 ret |= TIOCM_CAR;
636 if (status & SYNC)
637 ret |= TIOCM_DSR;
638 if (status & CTS)
639 ret |= TIOCM_CTS;
640
641 return ret;
642}
643
644/* The port lock is held and interrupts are disabled. */
645static void sunzilog_set_mctrl(struct uart_port *port, unsigned int mctrl)
646{
647 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
648 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
649 unsigned char set_bits, clear_bits;
650
651 set_bits = clear_bits = 0;
652
653 if (mctrl & TIOCM_RTS)
654 set_bits |= RTS;
655 else
656 clear_bits |= RTS;
657 if (mctrl & TIOCM_DTR)
658 set_bits |= DTR;
659 else
660 clear_bits |= DTR;
661
662 /* NOTE: Not subject to 'transmitter active' rule. */
663 up->curregs[R5] |= set_bits;
664 up->curregs[R5] &= ~clear_bits;
665 write_zsreg(channel, R5, up->curregs[R5]);
666}
667
668/* The port lock is held and interrupts are disabled. */
669static void sunzilog_stop_tx(struct uart_port *port)
670{
671 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
672
673 up->flags |= SUNZILOG_FLAG_TX_STOPPED;
674}
675
676/* The port lock is held and interrupts are disabled. */
677static void sunzilog_start_tx(struct uart_port *port)
678{
679 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
680 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
681 unsigned char status;
682
683 up->flags |= SUNZILOG_FLAG_TX_ACTIVE;
684 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED;
685
686 status = readb(&channel->control);
687 ZSDELAY();
688
689 /* TX busy? Just wait for the TX done interrupt. */
690 if (!(status & Tx_BUF_EMP))
691 return;
692
693 /* Send the first character to jump-start the TX done
694 * IRQ sending engine.
695 */
696 if (port->x_char) {
697 writeb(port->x_char, &channel->data);
698 ZSDELAY();
699 ZS_WSYNC(channel);
700
701 port->icount.tx++;
702 port->x_char = 0;
703 } else {
704 struct circ_buf *xmit = &port->state->xmit;
705
706 writeb(xmit->buf[xmit->tail], &channel->data);
707 ZSDELAY();
708 ZS_WSYNC(channel);
709
710 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
711 port->icount.tx++;
712
713 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
714 uart_write_wakeup(&up->port);
715 }
716}
717
718/* The port lock is held. */
719static void sunzilog_stop_rx(struct uart_port *port)
720{
721 struct uart_sunzilog_port *up = UART_ZILOG(port);
722 struct zilog_channel __iomem *channel;
723
724 if (ZS_IS_CONS(up))
725 return;
726
727 channel = ZILOG_CHANNEL_FROM_PORT(port);
728
729 /* Disable all RX interrupts. */
730 up->curregs[R1] &= ~RxINT_MASK;
731 sunzilog_maybe_update_regs(up, channel);
732}
733
734/* The port lock is held. */
735static void sunzilog_enable_ms(struct uart_port *port)
736{
737 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
738 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
739 unsigned char new_reg;
740
741 new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
742 if (new_reg != up->curregs[R15]) {
743 up->curregs[R15] = new_reg;
744
745 /* NOTE: Not subject to 'transmitter active' rule. */
746 write_zsreg(channel, R15, up->curregs[R15] & ~WR7pEN);
747 }
748}
749
750/* The port lock is not held. */
751static void sunzilog_break_ctl(struct uart_port *port, int break_state)
752{
753 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
754 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
755 unsigned char set_bits, clear_bits, new_reg;
756 unsigned long flags;
757
758 set_bits = clear_bits = 0;
759
760 if (break_state)
761 set_bits |= SND_BRK;
762 else
763 clear_bits |= SND_BRK;
764
765 spin_lock_irqsave(&port->lock, flags);
766
767 new_reg = (up->curregs[R5] | set_bits) & ~clear_bits;
768 if (new_reg != up->curregs[R5]) {
769 up->curregs[R5] = new_reg;
770
771 /* NOTE: Not subject to 'transmitter active' rule. */
772 write_zsreg(channel, R5, up->curregs[R5]);
773 }
774
775 spin_unlock_irqrestore(&port->lock, flags);
776}
777
778static void __sunzilog_startup(struct uart_sunzilog_port *up)
779{
780 struct zilog_channel __iomem *channel;
781
782 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
783 up->prev_status = readb(&channel->control);
784
785 /* Enable receiver and transmitter. */
786 up->curregs[R3] |= RxENAB;
787 up->curregs[R5] |= TxENAB;
788
789 up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
790 sunzilog_maybe_update_regs(up, channel);
791}
792
793static int sunzilog_startup(struct uart_port *port)
794{
795 struct uart_sunzilog_port *up = UART_ZILOG(port);
796 unsigned long flags;
797
798 if (ZS_IS_CONS(up))
799 return 0;
800
801 spin_lock_irqsave(&port->lock, flags);
802 __sunzilog_startup(up);
803 spin_unlock_irqrestore(&port->lock, flags);
804 return 0;
805}
806
807/*
808 * The test for ZS_IS_CONS is explained by the following e-mail:
809 *****
810 * From: Russell King <rmk@arm.linux.org.uk>
811 * Date: Sun, 8 Dec 2002 10:18:38 +0000
812 *
813 * On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote:
814 * > I boot my 2.5 boxes using "console=ttyS0,9600" argument,
815 * > and I noticed that something is not right with reference
816 * > counting in this case. It seems that when the console
817 * > is open by kernel initially, this is not accounted
818 * > as an open, and uart_startup is not called.
819 *
820 * That is correct. We are unable to call uart_startup when the serial
821 * console is initialised because it may need to allocate memory (as
822 * request_irq does) and the memory allocators may not have been
823 * initialised.
824 *
825 * 1. initialise the port into a state where it can send characters in the
826 * console write method.
827 *
828 * 2. don't do the actual hardware shutdown in your shutdown() method (but
829 * do the normal software shutdown - ie, free irqs etc)
830 *****
831 */
832static void sunzilog_shutdown(struct uart_port *port)
833{
834 struct uart_sunzilog_port *up = UART_ZILOG(port);
835 struct zilog_channel __iomem *channel;
836 unsigned long flags;
837
838 if (ZS_IS_CONS(up))
839 return;
840
841 spin_lock_irqsave(&port->lock, flags);
842
843 channel = ZILOG_CHANNEL_FROM_PORT(port);
844
845 /* Disable receiver and transmitter. */
846 up->curregs[R3] &= ~RxENAB;
847 up->curregs[R5] &= ~TxENAB;
848
849 /* Disable all interrupts and BRK assertion. */
850 up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
851 up->curregs[R5] &= ~SND_BRK;
852 sunzilog_maybe_update_regs(up, channel);
853
854 spin_unlock_irqrestore(&port->lock, flags);
855}
856
857/* Shared by TTY driver and serial console setup. The port lock is held
858 * and local interrupts are disabled.
859 */
860static void
861sunzilog_convert_to_zs(struct uart_sunzilog_port *up, unsigned int cflag,
862 unsigned int iflag, int brg)
863{
864
865 up->curregs[R10] = NRZ;
866 up->curregs[R11] = TCBR | RCBR;
867
868 /* Program BAUD and clock source. */
869 up->curregs[R4] &= ~XCLK_MASK;
870 up->curregs[R4] |= X16CLK;
871 up->curregs[R12] = brg & 0xff;
872 up->curregs[R13] = (brg >> 8) & 0xff;
873 up->curregs[R14] = BRSRC | BRENAB;
874
875 /* Character size, stop bits, and parity. */
876 up->curregs[R3] &= ~RxN_MASK;
877 up->curregs[R5] &= ~TxN_MASK;
878 switch (cflag & CSIZE) {
879 case CS5:
880 up->curregs[R3] |= Rx5;
881 up->curregs[R5] |= Tx5;
882 up->parity_mask = 0x1f;
883 break;
884 case CS6:
885 up->curregs[R3] |= Rx6;
886 up->curregs[R5] |= Tx6;
887 up->parity_mask = 0x3f;
888 break;
889 case CS7:
890 up->curregs[R3] |= Rx7;
891 up->curregs[R5] |= Tx7;
892 up->parity_mask = 0x7f;
893 break;
894 case CS8:
895 default:
896 up->curregs[R3] |= Rx8;
897 up->curregs[R5] |= Tx8;
898 up->parity_mask = 0xff;
899 break;
900 }
901 up->curregs[R4] &= ~0x0c;
902 if (cflag & CSTOPB)
903 up->curregs[R4] |= SB2;
904 else
905 up->curregs[R4] |= SB1;
906 if (cflag & PARENB)
907 up->curregs[R4] |= PAR_ENAB;
908 else
909 up->curregs[R4] &= ~PAR_ENAB;
910 if (!(cflag & PARODD))
911 up->curregs[R4] |= PAR_EVEN;
912 else
913 up->curregs[R4] &= ~PAR_EVEN;
914
915 up->port.read_status_mask = Rx_OVR;
916 if (iflag & INPCK)
917 up->port.read_status_mask |= CRC_ERR | PAR_ERR;
918 if (iflag & (BRKINT | PARMRK))
919 up->port.read_status_mask |= BRK_ABRT;
920
921 up->port.ignore_status_mask = 0;
922 if (iflag & IGNPAR)
923 up->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
924 if (iflag & IGNBRK) {
925 up->port.ignore_status_mask |= BRK_ABRT;
926 if (iflag & IGNPAR)
927 up->port.ignore_status_mask |= Rx_OVR;
928 }
929
930 if ((cflag & CREAD) == 0)
931 up->port.ignore_status_mask = 0xff;
932}
933
934/* The port lock is not held. */
935static void
936sunzilog_set_termios(struct uart_port *port, struct ktermios *termios,
937 struct ktermios *old)
938{
939 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
940 unsigned long flags;
941 int baud, brg;
942
943 baud = uart_get_baud_rate(port, termios, old, 1200, 76800);
944
945 spin_lock_irqsave(&up->port.lock, flags);
946
947 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
948
949 sunzilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg);
950
951 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
952 up->flags |= SUNZILOG_FLAG_MODEM_STATUS;
953 else
954 up->flags &= ~SUNZILOG_FLAG_MODEM_STATUS;
955
956 up->cflag = termios->c_cflag;
957
958 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port));
959
960 uart_update_timeout(port, termios->c_cflag, baud);
961
962 spin_unlock_irqrestore(&up->port.lock, flags);
963}
964
965static const char *sunzilog_type(struct uart_port *port)
966{
967 struct uart_sunzilog_port *up = UART_ZILOG(port);
968
969 return (up->flags & SUNZILOG_FLAG_ESCC) ? "zs (ESCC)" : "zs";
970}
971
972/* We do not request/release mappings of the registers here, this
973 * happens at early serial probe time.
974 */
975static void sunzilog_release_port(struct uart_port *port)
976{
977}
978
979static int sunzilog_request_port(struct uart_port *port)
980{
981 return 0;
982}
983
984/* These do not need to do anything interesting either. */
985static void sunzilog_config_port(struct uart_port *port, int flags)
986{
987}
988
989/* We do not support letting the user mess with the divisor, IRQ, etc. */
990static int sunzilog_verify_port(struct uart_port *port, struct serial_struct *ser)
991{
992 return -EINVAL;
993}
994
995#ifdef CONFIG_CONSOLE_POLL
996static int sunzilog_get_poll_char(struct uart_port *port)
997{
998 unsigned char ch, r1;
999 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *) port;
1000 struct zilog_channel __iomem *channel
1001 = ZILOG_CHANNEL_FROM_PORT(&up->port);
1002
1003
1004 r1 = read_zsreg(channel, R1);
1005 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
1006 writeb(ERR_RES, &channel->control);
1007 ZSDELAY();
1008 ZS_WSYNC(channel);
1009 }
1010
1011 ch = readb(&channel->control);
1012 ZSDELAY();
1013
1014 /* This funny hack depends upon BRK_ABRT not interfering
1015 * with the other bits we care about in R1.
1016 */
1017 if (ch & BRK_ABRT)
1018 r1 |= BRK_ABRT;
1019
1020 if (!(ch & Rx_CH_AV))
1021 return NO_POLL_CHAR;
1022
1023 ch = readb(&channel->data);
1024 ZSDELAY();
1025
1026 ch &= up->parity_mask;
1027 return ch;
1028}
1029
1030static void sunzilog_put_poll_char(struct uart_port *port,
1031 unsigned char ch)
1032{
1033 struct uart_sunzilog_port *up = (struct uart_sunzilog_port *)port;
1034
1035 sunzilog_putchar(&up->port, ch);
1036}
1037#endif /* CONFIG_CONSOLE_POLL */
1038
1039static struct uart_ops sunzilog_pops = {
1040 .tx_empty = sunzilog_tx_empty,
1041 .set_mctrl = sunzilog_set_mctrl,
1042 .get_mctrl = sunzilog_get_mctrl,
1043 .stop_tx = sunzilog_stop_tx,
1044 .start_tx = sunzilog_start_tx,
1045 .stop_rx = sunzilog_stop_rx,
1046 .enable_ms = sunzilog_enable_ms,
1047 .break_ctl = sunzilog_break_ctl,
1048 .startup = sunzilog_startup,
1049 .shutdown = sunzilog_shutdown,
1050 .set_termios = sunzilog_set_termios,
1051 .type = sunzilog_type,
1052 .release_port = sunzilog_release_port,
1053 .request_port = sunzilog_request_port,
1054 .config_port = sunzilog_config_port,
1055 .verify_port = sunzilog_verify_port,
1056#ifdef CONFIG_CONSOLE_POLL
1057 .poll_get_char = sunzilog_get_poll_char,
1058 .poll_put_char = sunzilog_put_poll_char,
1059#endif
1060};
1061
1062static int uart_chip_count;
1063static struct uart_sunzilog_port *sunzilog_port_table;
1064static struct zilog_layout __iomem **sunzilog_chip_regs;
1065
1066static struct uart_sunzilog_port *sunzilog_irq_chain;
1067
1068static struct uart_driver sunzilog_reg = {
1069 .owner = THIS_MODULE,
1070 .driver_name = "sunzilog",
1071 .dev_name = "ttyS",
1072 .major = TTY_MAJOR,
1073};
1074
1075static int __init sunzilog_alloc_tables(int num_sunzilog)
1076{
1077 struct uart_sunzilog_port *up;
1078 unsigned long size;
1079 int num_channels = num_sunzilog * 2;
1080 int i;
1081
1082 size = num_channels * sizeof(struct uart_sunzilog_port);
1083 sunzilog_port_table = kzalloc(size, GFP_KERNEL);
1084 if (!sunzilog_port_table)
1085 return -ENOMEM;
1086
1087 for (i = 0; i < num_channels; i++) {
1088 up = &sunzilog_port_table[i];
1089
1090 spin_lock_init(&up->port.lock);
1091
1092 if (i == 0)
1093 sunzilog_irq_chain = up;
1094
1095 if (i < num_channels - 1)
1096 up->next = up + 1;
1097 else
1098 up->next = NULL;
1099 }
1100
1101 size = num_sunzilog * sizeof(struct zilog_layout __iomem *);
1102 sunzilog_chip_regs = kzalloc(size, GFP_KERNEL);
1103 if (!sunzilog_chip_regs) {
1104 kfree(sunzilog_port_table);
1105 sunzilog_irq_chain = NULL;
1106 return -ENOMEM;
1107 }
1108
1109 return 0;
1110}
1111
1112static void sunzilog_free_tables(void)
1113{
1114 kfree(sunzilog_port_table);
1115 sunzilog_irq_chain = NULL;
1116 kfree(sunzilog_chip_regs);
1117}
1118
1119#define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */
1120
1121static void sunzilog_putchar(struct uart_port *port, int ch)
1122{
1123 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port);
1124 int loops = ZS_PUT_CHAR_MAX_DELAY;
1125
1126 /* This is a timed polling loop so do not switch the explicit
1127 * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM
1128 */
1129 do {
1130 unsigned char val = readb(&channel->control);
1131 if (val & Tx_BUF_EMP) {
1132 ZSDELAY();
1133 break;
1134 }
1135 udelay(5);
1136 } while (--loops);
1137
1138 writeb(ch, &channel->data);
1139 ZSDELAY();
1140 ZS_WSYNC(channel);
1141}
1142
1143#ifdef CONFIG_SERIO
1144
1145static DEFINE_SPINLOCK(sunzilog_serio_lock);
1146
1147static int sunzilog_serio_write(struct serio *serio, unsigned char ch)
1148{
1149 struct uart_sunzilog_port *up = serio->port_data;
1150 unsigned long flags;
1151
1152 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1153
1154 sunzilog_putchar(&up->port, ch);
1155
1156 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1157
1158 return 0;
1159}
1160
1161static int sunzilog_serio_open(struct serio *serio)
1162{
1163 struct uart_sunzilog_port *up = serio->port_data;
1164 unsigned long flags;
1165 int ret;
1166
1167 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1168 if (!up->serio_open) {
1169 up->serio_open = 1;
1170 ret = 0;
1171 } else
1172 ret = -EBUSY;
1173 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1174
1175 return ret;
1176}
1177
1178static void sunzilog_serio_close(struct serio *serio)
1179{
1180 struct uart_sunzilog_port *up = serio->port_data;
1181 unsigned long flags;
1182
1183 spin_lock_irqsave(&sunzilog_serio_lock, flags);
1184 up->serio_open = 0;
1185 spin_unlock_irqrestore(&sunzilog_serio_lock, flags);
1186}
1187
1188#endif /* CONFIG_SERIO */
1189
1190#ifdef CONFIG_SERIAL_SUNZILOG_CONSOLE
1191static void
1192sunzilog_console_write(struct console *con, const char *s, unsigned int count)
1193{
1194 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index];
1195 unsigned long flags;
1196 int locked = 1;
1197
1198 if (up->port.sysrq || oops_in_progress)
1199 locked = spin_trylock_irqsave(&up->port.lock, flags);
1200 else
1201 spin_lock_irqsave(&up->port.lock, flags);
1202
1203 uart_console_write(&up->port, s, count, sunzilog_putchar);
1204 udelay(2);
1205
1206 if (locked)
1207 spin_unlock_irqrestore(&up->port.lock, flags);
1208}
1209
1210static int __init sunzilog_console_setup(struct console *con, char *options)
1211{
1212 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index];
1213 unsigned long flags;
1214 int baud, brg;
1215
1216 if (up->port.type != PORT_SUNZILOG)
1217 return -1;
1218
1219 printk(KERN_INFO "Console: ttyS%d (SunZilog zs%d)\n",
1220 (sunzilog_reg.minor - 64) + con->index, con->index);
1221
1222 /* Get firmware console settings. */
1223 sunserial_console_termios(con, up->port.dev->of_node);
1224
1225 /* Firmware console speed is limited to 150-->38400 baud so
1226 * this hackish cflag thing is OK.
1227 */
1228 switch (con->cflag & CBAUD) {
1229 case B150: baud = 150; break;
1230 case B300: baud = 300; break;
1231 case B600: baud = 600; break;
1232 case B1200: baud = 1200; break;
1233 case B2400: baud = 2400; break;
1234 case B4800: baud = 4800; break;
1235 default: case B9600: baud = 9600; break;
1236 case B19200: baud = 19200; break;
1237 case B38400: baud = 38400; break;
1238 }
1239
1240 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1241
1242 spin_lock_irqsave(&up->port.lock, flags);
1243
1244 up->curregs[R15] |= BRKIE;
1245 sunzilog_convert_to_zs(up, con->cflag, 0, brg);
1246
1247 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS);
1248 __sunzilog_startup(up);
1249
1250 spin_unlock_irqrestore(&up->port.lock, flags);
1251
1252 return 0;
1253}
1254
1255static struct console sunzilog_console_ops = {
1256 .name = "ttyS",
1257 .write = sunzilog_console_write,
1258 .device = uart_console_device,
1259 .setup = sunzilog_console_setup,
1260 .flags = CON_PRINTBUFFER,
1261 .index = -1,
1262 .data = &sunzilog_reg,
1263};
1264
1265static inline struct console *SUNZILOG_CONSOLE(void)
1266{
1267 return &sunzilog_console_ops;
1268}
1269
1270#else
1271#define SUNZILOG_CONSOLE() (NULL)
1272#endif
1273
1274static void sunzilog_init_kbdms(struct uart_sunzilog_port *up)
1275{
1276 int baud, brg;
1277
1278 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) {
1279 up->cflag = B1200 | CS8 | CLOCAL | CREAD;
1280 baud = 1200;
1281 } else {
1282 up->cflag = B4800 | CS8 | CLOCAL | CREAD;
1283 baud = 4800;
1284 }
1285
1286 up->curregs[R15] |= BRKIE;
1287 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1288 sunzilog_convert_to_zs(up, up->cflag, 0, brg);
1289 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS);
1290 __sunzilog_startup(up);
1291}
1292
1293#ifdef CONFIG_SERIO
1294static void sunzilog_register_serio(struct uart_sunzilog_port *up)
1295{
1296 struct serio *serio = &up->serio;
1297
1298 serio->port_data = up;
1299
1300 serio->id.type = SERIO_RS232;
1301 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) {
1302 serio->id.proto = SERIO_SUNKBD;
1303 strlcpy(serio->name, "zskbd", sizeof(serio->name));
1304 } else {
1305 serio->id.proto = SERIO_SUN;
1306 serio->id.extra = 1;
1307 strlcpy(serio->name, "zsms", sizeof(serio->name));
1308 }
1309 strlcpy(serio->phys,
1310 ((up->flags & SUNZILOG_FLAG_CONS_KEYB) ?
1311 "zs/serio0" : "zs/serio1"),
1312 sizeof(serio->phys));
1313
1314 serio->write = sunzilog_serio_write;
1315 serio->open = sunzilog_serio_open;
1316 serio->close = sunzilog_serio_close;
1317 serio->dev.parent = up->port.dev;
1318
1319 serio_register_port(serio);
1320}
1321#endif
1322
1323static void sunzilog_init_hw(struct uart_sunzilog_port *up)
1324{
1325 struct zilog_channel __iomem *channel;
1326 unsigned long flags;
1327 int baud, brg;
1328
1329 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1330
1331 spin_lock_irqsave(&up->port.lock, flags);
1332 if (ZS_IS_CHANNEL_A(up)) {
1333 write_zsreg(channel, R9, FHWRES);
1334 ZSDELAY_LONG();
1335 (void) read_zsreg(channel, R0);
1336 }
1337
1338 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB |
1339 SUNZILOG_FLAG_CONS_MOUSE)) {
1340 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1341 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1342 up->curregs[R3] = RxENAB | Rx8;
1343 up->curregs[R5] = TxENAB | Tx8;
1344 up->curregs[R6] = 0x00; /* SDLC Address */
1345 up->curregs[R7] = 0x7E; /* SDLC Flag */
1346 up->curregs[R9] = NV;
1347 up->curregs[R7p] = 0x00;
1348 sunzilog_init_kbdms(up);
1349 /* Only enable interrupts if an ISR handler available */
1350 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER)
1351 up->curregs[R9] |= MIE;
1352 write_zsreg(channel, R9, up->curregs[R9]);
1353 } else {
1354 /* Normal serial TTY. */
1355 up->parity_mask = 0xff;
1356 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1357 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1358 up->curregs[R3] = RxENAB | Rx8;
1359 up->curregs[R5] = TxENAB | Tx8;
1360 up->curregs[R6] = 0x00; /* SDLC Address */
1361 up->curregs[R7] = 0x7E; /* SDLC Flag */
1362 up->curregs[R9] = NV;
1363 up->curregs[R10] = NRZ;
1364 up->curregs[R11] = TCBR | RCBR;
1365 baud = 9600;
1366 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1367 up->curregs[R12] = (brg & 0xff);
1368 up->curregs[R13] = (brg >> 8) & 0xff;
1369 up->curregs[R14] = BRSRC | BRENAB;
1370 up->curregs[R15] = FIFOEN; /* Use FIFO if on ESCC */
1371 up->curregs[R7p] = TxFIFO_LVL | RxFIFO_LVL;
1372 if (__load_zsregs(channel, up->curregs)) {
1373 up->flags |= SUNZILOG_FLAG_ESCC;
1374 }
1375 /* Only enable interrupts if an ISR handler available */
1376 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER)
1377 up->curregs[R9] |= MIE;
1378 write_zsreg(channel, R9, up->curregs[R9]);
1379 }
1380
1381 spin_unlock_irqrestore(&up->port.lock, flags);
1382
1383#ifdef CONFIG_SERIO
1384 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB |
1385 SUNZILOG_FLAG_CONS_MOUSE))
1386 sunzilog_register_serio(up);
1387#endif
1388}
1389
1390static int zilog_irq;
1391
1392static int zs_probe(struct platform_device *op)
1393{
1394 static int kbm_inst, uart_inst;
1395 int inst;
1396 struct uart_sunzilog_port *up;
1397 struct zilog_layout __iomem *rp;
1398 int keyboard_mouse = 0;
1399 int err;
1400
1401 if (of_find_property(op->dev.of_node, "keyboard", NULL))
1402 keyboard_mouse = 1;
1403
1404 /* uarts must come before keyboards/mice */
1405 if (keyboard_mouse)
1406 inst = uart_chip_count + kbm_inst;
1407 else
1408 inst = uart_inst;
1409
1410 sunzilog_chip_regs[inst] = of_ioremap(&op->resource[0], 0,
1411 sizeof(struct zilog_layout),
1412 "zs");
1413 if (!sunzilog_chip_regs[inst])
1414 return -ENOMEM;
1415
1416 rp = sunzilog_chip_regs[inst];
1417
1418 if (!zilog_irq)
1419 zilog_irq = op->archdata.irqs[0];
1420
1421 up = &sunzilog_port_table[inst * 2];
1422
1423 /* Channel A */
1424 up[0].port.mapbase = op->resource[0].start + 0x00;
1425 up[0].port.membase = (void __iomem *) &rp->channelA;
1426 up[0].port.iotype = UPIO_MEM;
1427 up[0].port.irq = op->archdata.irqs[0];
1428 up[0].port.uartclk = ZS_CLOCK;
1429 up[0].port.fifosize = 1;
1430 up[0].port.ops = &sunzilog_pops;
1431 up[0].port.type = PORT_SUNZILOG;
1432 up[0].port.flags = 0;
1433 up[0].port.line = (inst * 2) + 0;
1434 up[0].port.dev = &op->dev;
1435 up[0].flags |= SUNZILOG_FLAG_IS_CHANNEL_A;
1436 if (keyboard_mouse)
1437 up[0].flags |= SUNZILOG_FLAG_CONS_KEYB;
1438 sunzilog_init_hw(&up[0]);
1439
1440 /* Channel B */
1441 up[1].port.mapbase = op->resource[0].start + 0x04;
1442 up[1].port.membase = (void __iomem *) &rp->channelB;
1443 up[1].port.iotype = UPIO_MEM;
1444 up[1].port.irq = op->archdata.irqs[0];
1445 up[1].port.uartclk = ZS_CLOCK;
1446 up[1].port.fifosize = 1;
1447 up[1].port.ops = &sunzilog_pops;
1448 up[1].port.type = PORT_SUNZILOG;
1449 up[1].port.flags = 0;
1450 up[1].port.line = (inst * 2) + 1;
1451 up[1].port.dev = &op->dev;
1452 up[1].flags |= 0;
1453 if (keyboard_mouse)
1454 up[1].flags |= SUNZILOG_FLAG_CONS_MOUSE;
1455 sunzilog_init_hw(&up[1]);
1456
1457 if (!keyboard_mouse) {
1458 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node,
1459 &sunzilog_reg, up[0].port.line,
1460 false))
1461 up->flags |= SUNZILOG_FLAG_IS_CONS;
1462 err = uart_add_one_port(&sunzilog_reg, &up[0].port);
1463 if (err) {
1464 of_iounmap(&op->resource[0],
1465 rp, sizeof(struct zilog_layout));
1466 return err;
1467 }
1468 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node,
1469 &sunzilog_reg, up[1].port.line,
1470 false))
1471 up->flags |= SUNZILOG_FLAG_IS_CONS;
1472 err = uart_add_one_port(&sunzilog_reg, &up[1].port);
1473 if (err) {
1474 uart_remove_one_port(&sunzilog_reg, &up[0].port);
1475 of_iounmap(&op->resource[0],
1476 rp, sizeof(struct zilog_layout));
1477 return err;
1478 }
1479 uart_inst++;
1480 } else {
1481 printk(KERN_INFO "%s: Keyboard at MMIO 0x%llx (irq = %d) "
1482 "is a %s\n",
1483 dev_name(&op->dev),
1484 (unsigned long long) up[0].port.mapbase,
1485 op->archdata.irqs[0], sunzilog_type(&up[0].port));
1486 printk(KERN_INFO "%s: Mouse at MMIO 0x%llx (irq = %d) "
1487 "is a %s\n",
1488 dev_name(&op->dev),
1489 (unsigned long long) up[1].port.mapbase,
1490 op->archdata.irqs[0], sunzilog_type(&up[1].port));
1491 kbm_inst++;
1492 }
1493
1494 platform_set_drvdata(op, &up[0]);
1495
1496 return 0;
1497}
1498
1499static void zs_remove_one(struct uart_sunzilog_port *up)
1500{
1501 if (ZS_IS_KEYB(up) || ZS_IS_MOUSE(up)) {
1502#ifdef CONFIG_SERIO
1503 serio_unregister_port(&up->serio);
1504#endif
1505 } else
1506 uart_remove_one_port(&sunzilog_reg, &up->port);
1507}
1508
1509static int zs_remove(struct platform_device *op)
1510{
1511 struct uart_sunzilog_port *up = platform_get_drvdata(op);
1512 struct zilog_layout __iomem *regs;
1513
1514 zs_remove_one(&up[0]);
1515 zs_remove_one(&up[1]);
1516
1517 regs = sunzilog_chip_regs[up[0].port.line / 2];
1518 of_iounmap(&op->resource[0], regs, sizeof(struct zilog_layout));
1519
1520 return 0;
1521}
1522
1523static const struct of_device_id zs_match[] = {
1524 {
1525 .name = "zs",
1526 },
1527 {},
1528};
1529MODULE_DEVICE_TABLE(of, zs_match);
1530
1531static struct platform_driver zs_driver = {
1532 .driver = {
1533 .name = "zs",
1534 .owner = THIS_MODULE,
1535 .of_match_table = zs_match,
1536 },
1537 .probe = zs_probe,
1538 .remove = zs_remove,
1539};
1540
1541static int __init sunzilog_init(void)
1542{
1543 struct device_node *dp;
1544 int err;
1545 int num_keybms = 0;
1546 int num_sunzilog = 0;
1547
1548 for_each_node_by_name(dp, "zs") {
1549 num_sunzilog++;
1550 if (of_find_property(dp, "keyboard", NULL))
1551 num_keybms++;
1552 }
1553
1554 if (num_sunzilog) {
1555 err = sunzilog_alloc_tables(num_sunzilog);
1556 if (err)
1557 goto out;
1558
1559 uart_chip_count = num_sunzilog - num_keybms;
1560
1561 err = sunserial_register_minors(&sunzilog_reg,
1562 uart_chip_count * 2);
1563 if (err)
1564 goto out_free_tables;
1565 }
1566
1567 err = platform_driver_register(&zs_driver);
1568 if (err)
1569 goto out_unregister_uart;
1570
1571 if (zilog_irq) {
1572 struct uart_sunzilog_port *up = sunzilog_irq_chain;
1573 err = request_irq(zilog_irq, sunzilog_interrupt, IRQF_SHARED,
1574 "zs", sunzilog_irq_chain);
1575 if (err)
1576 goto out_unregister_driver;
1577
1578 /* Enable Interrupts */
1579 while (up) {
1580 struct zilog_channel __iomem *channel;
1581
1582 /* printk (KERN_INFO "Enable IRQ for ZILOG Hardware %p\n", up); */
1583 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1584 up->flags |= SUNZILOG_FLAG_ISR_HANDLER;
1585 up->curregs[R9] |= MIE;
1586 write_zsreg(channel, R9, up->curregs[R9]);
1587 up = up->next;
1588 }
1589 }
1590
1591out:
1592 return err;
1593
1594out_unregister_driver:
1595 platform_driver_unregister(&zs_driver);
1596
1597out_unregister_uart:
1598 if (num_sunzilog) {
1599 sunserial_unregister_minors(&sunzilog_reg, num_sunzilog);
1600 sunzilog_reg.cons = NULL;
1601 }
1602
1603out_free_tables:
1604 sunzilog_free_tables();
1605 goto out;
1606}
1607
1608static void __exit sunzilog_exit(void)
1609{
1610 platform_driver_unregister(&zs_driver);
1611
1612 if (zilog_irq) {
1613 struct uart_sunzilog_port *up = sunzilog_irq_chain;
1614
1615 /* Disable Interrupts */
1616 while (up) {
1617 struct zilog_channel __iomem *channel;
1618
1619 /* printk (KERN_INFO "Disable IRQ for ZILOG Hardware %p\n", up); */
1620 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
1621 up->flags &= ~SUNZILOG_FLAG_ISR_HANDLER;
1622 up->curregs[R9] &= ~MIE;
1623 write_zsreg(channel, R9, up->curregs[R9]);
1624 up = up->next;
1625 }
1626
1627 free_irq(zilog_irq, sunzilog_irq_chain);
1628 zilog_irq = 0;
1629 }
1630
1631 if (sunzilog_reg.nr) {
1632 sunserial_unregister_minors(&sunzilog_reg, sunzilog_reg.nr);
1633 sunzilog_free_tables();
1634 }
1635}
1636
1637module_init(sunzilog_init);
1638module_exit(sunzilog_exit);
1639
1640MODULE_AUTHOR("David S. Miller");
1641MODULE_DESCRIPTION("Sun Zilog serial port driver");
1642MODULE_VERSION("2.0");
1643MODULE_LICENSE("GPL");