Loading...
Note: File does not exist in v6.8.
1/*
2 * mfd.c: driver for High Speed UART device of Intel Medfield platform
3 *
4 * Refer pxa.c, 8250.c and some other drivers in drivers/serial/
5 *
6 * (C) Copyright 2010 Intel Corporation
7 *
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License
10 * as published by the Free Software Foundation; version 2
11 * of the License.
12 */
13
14/* Notes:
15 * 1. DMA channel allocation: 0/1 channel are assigned to port 0,
16 * 2/3 chan to port 1, 4/5 chan to port 3. Even number chans
17 * are used for RX, odd chans for TX
18 *
19 * 2. The RI/DSR/DCD/DTR are not pinned out, DCD & DSR are always
20 * asserted, only when the HW is reset the DDCD and DDSR will
21 * be triggered
22 */
23
24#if defined(CONFIG_SERIAL_MFD_HSU_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
25#define SUPPORT_SYSRQ
26#endif
27
28#include <linux/module.h>
29#include <linux/init.h>
30#include <linux/console.h>
31#include <linux/sysrq.h>
32#include <linux/slab.h>
33#include <linux/serial_reg.h>
34#include <linux/circ_buf.h>
35#include <linux/delay.h>
36#include <linux/interrupt.h>
37#include <linux/tty.h>
38#include <linux/tty_flip.h>
39#include <linux/serial_core.h>
40#include <linux/serial_mfd.h>
41#include <linux/dma-mapping.h>
42#include <linux/pci.h>
43#include <linux/nmi.h>
44#include <linux/io.h>
45#include <linux/debugfs.h>
46#include <linux/pm_runtime.h>
47
48#define HSU_DMA_BUF_SIZE 2048
49
50#define chan_readl(chan, offset) readl(chan->reg + offset)
51#define chan_writel(chan, offset, val) writel(val, chan->reg + offset)
52
53#define mfd_readl(obj, offset) readl(obj->reg + offset)
54#define mfd_writel(obj, offset, val) writel(val, obj->reg + offset)
55
56static int hsu_dma_enable;
57module_param(hsu_dma_enable, int, 0);
58MODULE_PARM_DESC(hsu_dma_enable,
59 "It is a bitmap to set working mode, if bit[x] is 1, then port[x] will work in DMA mode, otherwise in PIO mode.");
60
61struct hsu_dma_buffer {
62 u8 *buf;
63 dma_addr_t dma_addr;
64 u32 dma_size;
65 u32 ofs;
66};
67
68struct hsu_dma_chan {
69 u32 id;
70 enum dma_data_direction dirt;
71 struct uart_hsu_port *uport;
72 void __iomem *reg;
73};
74
75struct uart_hsu_port {
76 struct uart_port port;
77 unsigned char ier;
78 unsigned char lcr;
79 unsigned char mcr;
80 unsigned int lsr_break_flag;
81 char name[12];
82 int index;
83 struct device *dev;
84
85 struct hsu_dma_chan *txc;
86 struct hsu_dma_chan *rxc;
87 struct hsu_dma_buffer txbuf;
88 struct hsu_dma_buffer rxbuf;
89 int use_dma; /* flag for DMA/PIO */
90 int running;
91 int dma_tx_on;
92};
93
94/* Top level data structure of HSU */
95struct hsu_port {
96 void __iomem *reg;
97 unsigned long paddr;
98 unsigned long iolen;
99 u32 irq;
100
101 struct uart_hsu_port port[3];
102 struct hsu_dma_chan chans[10];
103
104 struct dentry *debugfs;
105};
106
107static inline unsigned int serial_in(struct uart_hsu_port *up, int offset)
108{
109 unsigned int val;
110
111 if (offset > UART_MSR) {
112 offset <<= 2;
113 val = readl(up->port.membase + offset);
114 } else
115 val = (unsigned int)readb(up->port.membase + offset);
116
117 return val;
118}
119
120static inline void serial_out(struct uart_hsu_port *up, int offset, int value)
121{
122 if (offset > UART_MSR) {
123 offset <<= 2;
124 writel(value, up->port.membase + offset);
125 } else {
126 unsigned char val = value & 0xff;
127 writeb(val, up->port.membase + offset);
128 }
129}
130
131#ifdef CONFIG_DEBUG_FS
132
133#define HSU_REGS_BUFSIZE 1024
134
135
136static ssize_t port_show_regs(struct file *file, char __user *user_buf,
137 size_t count, loff_t *ppos)
138{
139 struct uart_hsu_port *up = file->private_data;
140 char *buf;
141 u32 len = 0;
142 ssize_t ret;
143
144 buf = kzalloc(HSU_REGS_BUFSIZE, GFP_KERNEL);
145 if (!buf)
146 return 0;
147
148 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
149 "MFD HSU port[%d] regs:\n", up->index);
150
151 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
152 "=================================\n");
153 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
154 "IER: \t\t0x%08x\n", serial_in(up, UART_IER));
155 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
156 "IIR: \t\t0x%08x\n", serial_in(up, UART_IIR));
157 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
158 "LCR: \t\t0x%08x\n", serial_in(up, UART_LCR));
159 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
160 "MCR: \t\t0x%08x\n", serial_in(up, UART_MCR));
161 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
162 "LSR: \t\t0x%08x\n", serial_in(up, UART_LSR));
163 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
164 "MSR: \t\t0x%08x\n", serial_in(up, UART_MSR));
165 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
166 "FOR: \t\t0x%08x\n", serial_in(up, UART_FOR));
167 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
168 "PS: \t\t0x%08x\n", serial_in(up, UART_PS));
169 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
170 "MUL: \t\t0x%08x\n", serial_in(up, UART_MUL));
171 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
172 "DIV: \t\t0x%08x\n", serial_in(up, UART_DIV));
173
174 if (len > HSU_REGS_BUFSIZE)
175 len = HSU_REGS_BUFSIZE;
176
177 ret = simple_read_from_buffer(user_buf, count, ppos, buf, len);
178 kfree(buf);
179 return ret;
180}
181
182static ssize_t dma_show_regs(struct file *file, char __user *user_buf,
183 size_t count, loff_t *ppos)
184{
185 struct hsu_dma_chan *chan = file->private_data;
186 char *buf;
187 u32 len = 0;
188 ssize_t ret;
189
190 buf = kzalloc(HSU_REGS_BUFSIZE, GFP_KERNEL);
191 if (!buf)
192 return 0;
193
194 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
195 "MFD HSU DMA channel [%d] regs:\n", chan->id);
196
197 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
198 "=================================\n");
199 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
200 "CR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_CR));
201 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
202 "DCR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_DCR));
203 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
204 "BSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_BSR));
205 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
206 "MOTSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_MOTSR));
207 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
208 "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D0SAR));
209 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
210 "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D0TSR));
211 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
212 "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D1SAR));
213 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
214 "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D1TSR));
215 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
216 "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D2SAR));
217 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
218 "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D2TSR));
219 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
220 "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D3SAR));
221 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
222 "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D3TSR));
223
224 if (len > HSU_REGS_BUFSIZE)
225 len = HSU_REGS_BUFSIZE;
226
227 ret = simple_read_from_buffer(user_buf, count, ppos, buf, len);
228 kfree(buf);
229 return ret;
230}
231
232static const struct file_operations port_regs_ops = {
233 .owner = THIS_MODULE,
234 .open = simple_open,
235 .read = port_show_regs,
236 .llseek = default_llseek,
237};
238
239static const struct file_operations dma_regs_ops = {
240 .owner = THIS_MODULE,
241 .open = simple_open,
242 .read = dma_show_regs,
243 .llseek = default_llseek,
244};
245
246static int hsu_debugfs_init(struct hsu_port *hsu)
247{
248 int i;
249 char name[32];
250
251 hsu->debugfs = debugfs_create_dir("hsu", NULL);
252 if (!hsu->debugfs)
253 return -ENOMEM;
254
255 for (i = 0; i < 3; i++) {
256 snprintf(name, sizeof(name), "port_%d_regs", i);
257 debugfs_create_file(name, S_IFREG | S_IRUGO,
258 hsu->debugfs, (void *)(&hsu->port[i]), &port_regs_ops);
259 }
260
261 for (i = 0; i < 6; i++) {
262 snprintf(name, sizeof(name), "dma_chan_%d_regs", i);
263 debugfs_create_file(name, S_IFREG | S_IRUGO,
264 hsu->debugfs, (void *)&hsu->chans[i], &dma_regs_ops);
265 }
266
267 return 0;
268}
269
270static void hsu_debugfs_remove(struct hsu_port *hsu)
271{
272 if (hsu->debugfs)
273 debugfs_remove_recursive(hsu->debugfs);
274}
275
276#else
277static inline int hsu_debugfs_init(struct hsu_port *hsu)
278{
279 return 0;
280}
281
282static inline void hsu_debugfs_remove(struct hsu_port *hsu)
283{
284}
285#endif /* CONFIG_DEBUG_FS */
286
287static void serial_hsu_enable_ms(struct uart_port *port)
288{
289 struct uart_hsu_port *up =
290 container_of(port, struct uart_hsu_port, port);
291
292 up->ier |= UART_IER_MSI;
293 serial_out(up, UART_IER, up->ier);
294}
295
296static void hsu_dma_tx(struct uart_hsu_port *up)
297{
298 struct circ_buf *xmit = &up->port.state->xmit;
299 struct hsu_dma_buffer *dbuf = &up->txbuf;
300 int count;
301
302 /* test_and_set_bit may be better, but anyway it's in lock protected mode */
303 if (up->dma_tx_on)
304 return;
305
306 /* Update the circ buf info */
307 xmit->tail += dbuf->ofs;
308 xmit->tail &= UART_XMIT_SIZE - 1;
309
310 up->port.icount.tx += dbuf->ofs;
311 dbuf->ofs = 0;
312
313 /* Disable the channel */
314 chan_writel(up->txc, HSU_CH_CR, 0x0);
315
316 if (!uart_circ_empty(xmit) && !uart_tx_stopped(&up->port)) {
317 dma_sync_single_for_device(up->port.dev,
318 dbuf->dma_addr,
319 dbuf->dma_size,
320 DMA_TO_DEVICE);
321
322 count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
323 dbuf->ofs = count;
324
325 /* Reprogram the channel */
326 chan_writel(up->txc, HSU_CH_D0SAR, dbuf->dma_addr + xmit->tail);
327 chan_writel(up->txc, HSU_CH_D0TSR, count);
328
329 /* Reenable the channel */
330 chan_writel(up->txc, HSU_CH_DCR, 0x1
331 | (0x1 << 8)
332 | (0x1 << 16)
333 | (0x1 << 24));
334 up->dma_tx_on = 1;
335 chan_writel(up->txc, HSU_CH_CR, 0x1);
336 }
337
338 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
339 uart_write_wakeup(&up->port);
340}
341
342/* The buffer is already cache coherent */
343static void hsu_dma_start_rx_chan(struct hsu_dma_chan *rxc,
344 struct hsu_dma_buffer *dbuf)
345{
346 dbuf->ofs = 0;
347
348 chan_writel(rxc, HSU_CH_BSR, 32);
349 chan_writel(rxc, HSU_CH_MOTSR, 4);
350
351 chan_writel(rxc, HSU_CH_D0SAR, dbuf->dma_addr);
352 chan_writel(rxc, HSU_CH_D0TSR, dbuf->dma_size);
353 chan_writel(rxc, HSU_CH_DCR, 0x1 | (0x1 << 8)
354 | (0x1 << 16)
355 | (0x1 << 24) /* timeout bit, see HSU Errata 1 */
356 );
357 chan_writel(rxc, HSU_CH_CR, 0x3);
358}
359
360/* Protected by spin_lock_irqsave(port->lock) */
361static void serial_hsu_start_tx(struct uart_port *port)
362{
363 struct uart_hsu_port *up =
364 container_of(port, struct uart_hsu_port, port);
365
366 if (up->use_dma) {
367 hsu_dma_tx(up);
368 } else if (!(up->ier & UART_IER_THRI)) {
369 up->ier |= UART_IER_THRI;
370 serial_out(up, UART_IER, up->ier);
371 }
372}
373
374static void serial_hsu_stop_tx(struct uart_port *port)
375{
376 struct uart_hsu_port *up =
377 container_of(port, struct uart_hsu_port, port);
378 struct hsu_dma_chan *txc = up->txc;
379
380 if (up->use_dma)
381 chan_writel(txc, HSU_CH_CR, 0x0);
382 else if (up->ier & UART_IER_THRI) {
383 up->ier &= ~UART_IER_THRI;
384 serial_out(up, UART_IER, up->ier);
385 }
386}
387
388/* This is always called in spinlock protected mode, so
389 * modify timeout timer is safe here */
390static void hsu_dma_rx(struct uart_hsu_port *up, u32 int_sts,
391 unsigned long *flags)
392{
393 struct hsu_dma_buffer *dbuf = &up->rxbuf;
394 struct hsu_dma_chan *chan = up->rxc;
395 struct uart_port *port = &up->port;
396 struct tty_port *tport = &port->state->port;
397 int count;
398
399 /*
400 * First need to know how many is already transferred,
401 * then check if its a timeout DMA irq, and return
402 * the trail bytes out, push them up and reenable the
403 * channel
404 */
405
406 /* Timeout IRQ, need wait some time, see Errata 2 */
407 if (int_sts & 0xf00)
408 udelay(2);
409
410 /* Stop the channel */
411 chan_writel(chan, HSU_CH_CR, 0x0);
412
413 count = chan_readl(chan, HSU_CH_D0SAR) - dbuf->dma_addr;
414 if (!count) {
415 /* Restart the channel before we leave */
416 chan_writel(chan, HSU_CH_CR, 0x3);
417 return;
418 }
419
420 dma_sync_single_for_cpu(port->dev, dbuf->dma_addr,
421 dbuf->dma_size, DMA_FROM_DEVICE);
422
423 /*
424 * Head will only wrap around when we recycle
425 * the DMA buffer, and when that happens, we
426 * explicitly set tail to 0. So head will
427 * always be greater than tail.
428 */
429 tty_insert_flip_string(tport, dbuf->buf, count);
430 port->icount.rx += count;
431
432 dma_sync_single_for_device(up->port.dev, dbuf->dma_addr,
433 dbuf->dma_size, DMA_FROM_DEVICE);
434
435 /* Reprogram the channel */
436 chan_writel(chan, HSU_CH_D0SAR, dbuf->dma_addr);
437 chan_writel(chan, HSU_CH_D0TSR, dbuf->dma_size);
438 chan_writel(chan, HSU_CH_DCR, 0x1
439 | (0x1 << 8)
440 | (0x1 << 16)
441 | (0x1 << 24) /* timeout bit, see HSU Errata 1 */
442 );
443 spin_unlock_irqrestore(&up->port.lock, *flags);
444 tty_flip_buffer_push(tport);
445 spin_lock_irqsave(&up->port.lock, *flags);
446
447 chan_writel(chan, HSU_CH_CR, 0x3);
448
449}
450
451static void serial_hsu_stop_rx(struct uart_port *port)
452{
453 struct uart_hsu_port *up =
454 container_of(port, struct uart_hsu_port, port);
455 struct hsu_dma_chan *chan = up->rxc;
456
457 if (up->use_dma)
458 chan_writel(chan, HSU_CH_CR, 0x2);
459 else {
460 up->ier &= ~UART_IER_RLSI;
461 up->port.read_status_mask &= ~UART_LSR_DR;
462 serial_out(up, UART_IER, up->ier);
463 }
464}
465
466static inline void receive_chars(struct uart_hsu_port *up, int *status,
467 unsigned long *flags)
468{
469 unsigned int ch, flag;
470 unsigned int max_count = 256;
471
472 do {
473 ch = serial_in(up, UART_RX);
474 flag = TTY_NORMAL;
475 up->port.icount.rx++;
476
477 if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
478 UART_LSR_FE | UART_LSR_OE))) {
479
480 dev_warn(up->dev, "We really rush into ERR/BI case"
481 "status = 0x%02x", *status);
482 /* For statistics only */
483 if (*status & UART_LSR_BI) {
484 *status &= ~(UART_LSR_FE | UART_LSR_PE);
485 up->port.icount.brk++;
486 /*
487 * We do the SysRQ and SAK checking
488 * here because otherwise the break
489 * may get masked by ignore_status_mask
490 * or read_status_mask.
491 */
492 if (uart_handle_break(&up->port))
493 goto ignore_char;
494 } else if (*status & UART_LSR_PE)
495 up->port.icount.parity++;
496 else if (*status & UART_LSR_FE)
497 up->port.icount.frame++;
498 if (*status & UART_LSR_OE)
499 up->port.icount.overrun++;
500
501 /* Mask off conditions which should be ignored. */
502 *status &= up->port.read_status_mask;
503
504#ifdef CONFIG_SERIAL_MFD_HSU_CONSOLE
505 if (up->port.cons &&
506 up->port.cons->index == up->port.line) {
507 /* Recover the break flag from console xmit */
508 *status |= up->lsr_break_flag;
509 up->lsr_break_flag = 0;
510 }
511#endif
512 if (*status & UART_LSR_BI) {
513 flag = TTY_BREAK;
514 } else if (*status & UART_LSR_PE)
515 flag = TTY_PARITY;
516 else if (*status & UART_LSR_FE)
517 flag = TTY_FRAME;
518 }
519
520 if (uart_handle_sysrq_char(&up->port, ch))
521 goto ignore_char;
522
523 uart_insert_char(&up->port, *status, UART_LSR_OE, ch, flag);
524 ignore_char:
525 *status = serial_in(up, UART_LSR);
526 } while ((*status & UART_LSR_DR) && max_count--);
527
528 spin_unlock_irqrestore(&up->port.lock, *flags);
529 tty_flip_buffer_push(&up->port.state->port);
530 spin_lock_irqsave(&up->port.lock, *flags);
531}
532
533static void transmit_chars(struct uart_hsu_port *up)
534{
535 struct circ_buf *xmit = &up->port.state->xmit;
536 int count;
537
538 if (up->port.x_char) {
539 serial_out(up, UART_TX, up->port.x_char);
540 up->port.icount.tx++;
541 up->port.x_char = 0;
542 return;
543 }
544 if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
545 serial_hsu_stop_tx(&up->port);
546 return;
547 }
548
549 /* The IRQ is for TX FIFO half-empty */
550 count = up->port.fifosize / 2;
551
552 do {
553 serial_out(up, UART_TX, xmit->buf[xmit->tail]);
554 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
555
556 up->port.icount.tx++;
557 if (uart_circ_empty(xmit))
558 break;
559 } while (--count > 0);
560
561 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
562 uart_write_wakeup(&up->port);
563
564 if (uart_circ_empty(xmit))
565 serial_hsu_stop_tx(&up->port);
566}
567
568static inline void check_modem_status(struct uart_hsu_port *up)
569{
570 int status;
571
572 status = serial_in(up, UART_MSR);
573
574 if ((status & UART_MSR_ANY_DELTA) == 0)
575 return;
576
577 if (status & UART_MSR_TERI)
578 up->port.icount.rng++;
579 if (status & UART_MSR_DDSR)
580 up->port.icount.dsr++;
581 /* We may only get DDCD when HW init and reset */
582 if (status & UART_MSR_DDCD)
583 uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
584 /* Will start/stop_tx accordingly */
585 if (status & UART_MSR_DCTS)
586 uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
587
588 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
589}
590
591/*
592 * This handles the interrupt from one port.
593 */
594static irqreturn_t port_irq(int irq, void *dev_id)
595{
596 struct uart_hsu_port *up = dev_id;
597 unsigned int iir, lsr;
598 unsigned long flags;
599
600 if (unlikely(!up->running))
601 return IRQ_NONE;
602
603 spin_lock_irqsave(&up->port.lock, flags);
604 if (up->use_dma) {
605 lsr = serial_in(up, UART_LSR);
606 if (unlikely(lsr & (UART_LSR_BI | UART_LSR_PE |
607 UART_LSR_FE | UART_LSR_OE)))
608 dev_warn(up->dev,
609 "Got lsr irq while using DMA, lsr = 0x%2x\n",
610 lsr);
611 check_modem_status(up);
612 spin_unlock_irqrestore(&up->port.lock, flags);
613 return IRQ_HANDLED;
614 }
615
616 iir = serial_in(up, UART_IIR);
617 if (iir & UART_IIR_NO_INT) {
618 spin_unlock_irqrestore(&up->port.lock, flags);
619 return IRQ_NONE;
620 }
621
622 lsr = serial_in(up, UART_LSR);
623 if (lsr & UART_LSR_DR)
624 receive_chars(up, &lsr, &flags);
625 check_modem_status(up);
626
627 /* lsr will be renewed during the receive_chars */
628 if (lsr & UART_LSR_THRE)
629 transmit_chars(up);
630
631 spin_unlock_irqrestore(&up->port.lock, flags);
632 return IRQ_HANDLED;
633}
634
635static inline void dma_chan_irq(struct hsu_dma_chan *chan)
636{
637 struct uart_hsu_port *up = chan->uport;
638 unsigned long flags;
639 u32 int_sts;
640
641 spin_lock_irqsave(&up->port.lock, flags);
642
643 if (!up->use_dma || !up->running)
644 goto exit;
645
646 /*
647 * No matter what situation, need read clear the IRQ status
648 * There is a bug, see Errata 5, HSD 2900918
649 */
650 int_sts = chan_readl(chan, HSU_CH_SR);
651
652 /* Rx channel */
653 if (chan->dirt == DMA_FROM_DEVICE)
654 hsu_dma_rx(up, int_sts, &flags);
655
656 /* Tx channel */
657 if (chan->dirt == DMA_TO_DEVICE) {
658 chan_writel(chan, HSU_CH_CR, 0x0);
659 up->dma_tx_on = 0;
660 hsu_dma_tx(up);
661 }
662
663exit:
664 spin_unlock_irqrestore(&up->port.lock, flags);
665 return;
666}
667
668static irqreturn_t dma_irq(int irq, void *dev_id)
669{
670 struct hsu_port *hsu = dev_id;
671 u32 int_sts, i;
672
673 int_sts = mfd_readl(hsu, HSU_GBL_DMAISR);
674
675 /* Currently we only have 6 channels may be used */
676 for (i = 0; i < 6; i++) {
677 if (int_sts & 0x1)
678 dma_chan_irq(&hsu->chans[i]);
679 int_sts >>= 1;
680 }
681
682 return IRQ_HANDLED;
683}
684
685static unsigned int serial_hsu_tx_empty(struct uart_port *port)
686{
687 struct uart_hsu_port *up =
688 container_of(port, struct uart_hsu_port, port);
689 unsigned long flags;
690 unsigned int ret;
691
692 spin_lock_irqsave(&up->port.lock, flags);
693 ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
694 spin_unlock_irqrestore(&up->port.lock, flags);
695
696 return ret;
697}
698
699static unsigned int serial_hsu_get_mctrl(struct uart_port *port)
700{
701 struct uart_hsu_port *up =
702 container_of(port, struct uart_hsu_port, port);
703 unsigned char status;
704 unsigned int ret;
705
706 status = serial_in(up, UART_MSR);
707
708 ret = 0;
709 if (status & UART_MSR_DCD)
710 ret |= TIOCM_CAR;
711 if (status & UART_MSR_RI)
712 ret |= TIOCM_RNG;
713 if (status & UART_MSR_DSR)
714 ret |= TIOCM_DSR;
715 if (status & UART_MSR_CTS)
716 ret |= TIOCM_CTS;
717 return ret;
718}
719
720static void serial_hsu_set_mctrl(struct uart_port *port, unsigned int mctrl)
721{
722 struct uart_hsu_port *up =
723 container_of(port, struct uart_hsu_port, port);
724 unsigned char mcr = 0;
725
726 if (mctrl & TIOCM_RTS)
727 mcr |= UART_MCR_RTS;
728 if (mctrl & TIOCM_DTR)
729 mcr |= UART_MCR_DTR;
730 if (mctrl & TIOCM_OUT1)
731 mcr |= UART_MCR_OUT1;
732 if (mctrl & TIOCM_OUT2)
733 mcr |= UART_MCR_OUT2;
734 if (mctrl & TIOCM_LOOP)
735 mcr |= UART_MCR_LOOP;
736
737 mcr |= up->mcr;
738
739 serial_out(up, UART_MCR, mcr);
740}
741
742static void serial_hsu_break_ctl(struct uart_port *port, int break_state)
743{
744 struct uart_hsu_port *up =
745 container_of(port, struct uart_hsu_port, port);
746 unsigned long flags;
747
748 spin_lock_irqsave(&up->port.lock, flags);
749 if (break_state == -1)
750 up->lcr |= UART_LCR_SBC;
751 else
752 up->lcr &= ~UART_LCR_SBC;
753 serial_out(up, UART_LCR, up->lcr);
754 spin_unlock_irqrestore(&up->port.lock, flags);
755}
756
757/*
758 * What special to do:
759 * 1. chose the 64B fifo mode
760 * 2. start dma or pio depends on configuration
761 * 3. we only allocate dma memory when needed
762 */
763static int serial_hsu_startup(struct uart_port *port)
764{
765 struct uart_hsu_port *up =
766 container_of(port, struct uart_hsu_port, port);
767 unsigned long flags;
768
769 pm_runtime_get_sync(up->dev);
770
771 /*
772 * Clear the FIFO buffers and disable them.
773 * (they will be reenabled in set_termios())
774 */
775 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
776 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
777 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
778 serial_out(up, UART_FCR, 0);
779
780 /* Clear the interrupt registers. */
781 (void) serial_in(up, UART_LSR);
782 (void) serial_in(up, UART_RX);
783 (void) serial_in(up, UART_IIR);
784 (void) serial_in(up, UART_MSR);
785
786 /* Now, initialize the UART, default is 8n1 */
787 serial_out(up, UART_LCR, UART_LCR_WLEN8);
788
789 spin_lock_irqsave(&up->port.lock, flags);
790
791 up->port.mctrl |= TIOCM_OUT2;
792 serial_hsu_set_mctrl(&up->port, up->port.mctrl);
793
794 /*
795 * Finally, enable interrupts. Note: Modem status interrupts
796 * are set via set_termios(), which will be occurring imminently
797 * anyway, so we don't enable them here.
798 */
799 if (!up->use_dma)
800 up->ier = UART_IER_RLSI | UART_IER_RDI | UART_IER_RTOIE;
801 else
802 up->ier = 0;
803 serial_out(up, UART_IER, up->ier);
804
805 spin_unlock_irqrestore(&up->port.lock, flags);
806
807 /* DMA init */
808 if (up->use_dma) {
809 struct hsu_dma_buffer *dbuf;
810 struct circ_buf *xmit = &port->state->xmit;
811
812 up->dma_tx_on = 0;
813
814 /* First allocate the RX buffer */
815 dbuf = &up->rxbuf;
816 dbuf->buf = kzalloc(HSU_DMA_BUF_SIZE, GFP_KERNEL);
817 if (!dbuf->buf) {
818 up->use_dma = 0;
819 goto exit;
820 }
821 dbuf->dma_addr = dma_map_single(port->dev,
822 dbuf->buf,
823 HSU_DMA_BUF_SIZE,
824 DMA_FROM_DEVICE);
825 dbuf->dma_size = HSU_DMA_BUF_SIZE;
826
827 /* Start the RX channel right now */
828 hsu_dma_start_rx_chan(up->rxc, dbuf);
829
830 /* Next init the TX DMA */
831 dbuf = &up->txbuf;
832 dbuf->buf = xmit->buf;
833 dbuf->dma_addr = dma_map_single(port->dev,
834 dbuf->buf,
835 UART_XMIT_SIZE,
836 DMA_TO_DEVICE);
837 dbuf->dma_size = UART_XMIT_SIZE;
838
839 /* This should not be changed all around */
840 chan_writel(up->txc, HSU_CH_BSR, 32);
841 chan_writel(up->txc, HSU_CH_MOTSR, 4);
842 dbuf->ofs = 0;
843 }
844
845exit:
846 /* And clear the interrupt registers again for luck. */
847 (void) serial_in(up, UART_LSR);
848 (void) serial_in(up, UART_RX);
849 (void) serial_in(up, UART_IIR);
850 (void) serial_in(up, UART_MSR);
851
852 up->running = 1;
853 return 0;
854}
855
856static void serial_hsu_shutdown(struct uart_port *port)
857{
858 struct uart_hsu_port *up =
859 container_of(port, struct uart_hsu_port, port);
860 unsigned long flags;
861
862 /* Disable interrupts from this port */
863 up->ier = 0;
864 serial_out(up, UART_IER, 0);
865 up->running = 0;
866
867 spin_lock_irqsave(&up->port.lock, flags);
868 up->port.mctrl &= ~TIOCM_OUT2;
869 serial_hsu_set_mctrl(&up->port, up->port.mctrl);
870 spin_unlock_irqrestore(&up->port.lock, flags);
871
872 /* Disable break condition and FIFOs */
873 serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC);
874 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
875 UART_FCR_CLEAR_RCVR |
876 UART_FCR_CLEAR_XMIT);
877 serial_out(up, UART_FCR, 0);
878
879 pm_runtime_put(up->dev);
880}
881
882static void
883serial_hsu_set_termios(struct uart_port *port, struct ktermios *termios,
884 struct ktermios *old)
885{
886 struct uart_hsu_port *up =
887 container_of(port, struct uart_hsu_port, port);
888 unsigned char cval, fcr = 0;
889 unsigned long flags;
890 unsigned int baud, quot;
891 u32 ps, mul;
892
893 switch (termios->c_cflag & CSIZE) {
894 case CS5:
895 cval = UART_LCR_WLEN5;
896 break;
897 case CS6:
898 cval = UART_LCR_WLEN6;
899 break;
900 case CS7:
901 cval = UART_LCR_WLEN7;
902 break;
903 default:
904 case CS8:
905 cval = UART_LCR_WLEN8;
906 break;
907 }
908
909 /* CMSPAR isn't supported by this driver */
910 termios->c_cflag &= ~CMSPAR;
911
912 if (termios->c_cflag & CSTOPB)
913 cval |= UART_LCR_STOP;
914 if (termios->c_cflag & PARENB)
915 cval |= UART_LCR_PARITY;
916 if (!(termios->c_cflag & PARODD))
917 cval |= UART_LCR_EPAR;
918
919 /*
920 * The base clk is 50Mhz, and the baud rate come from:
921 * baud = 50M * MUL / (DIV * PS * DLAB)
922 *
923 * For those basic low baud rate we can get the direct
924 * scalar from 2746800, like 115200 = 2746800/24. For those
925 * higher baud rate, we handle them case by case, mainly by
926 * adjusting the MUL/PS registers, and DIV register is kept
927 * as default value 0x3d09 to make things simple
928 */
929 baud = uart_get_baud_rate(port, termios, old, 0, 4000000);
930
931 quot = 1;
932 ps = 0x10;
933 mul = 0x3600;
934 switch (baud) {
935 case 3500000:
936 mul = 0x3345;
937 ps = 0xC;
938 break;
939 case 1843200:
940 mul = 0x2400;
941 break;
942 case 3000000:
943 case 2500000:
944 case 2000000:
945 case 1500000:
946 case 1000000:
947 case 500000:
948 /* mul/ps/quot = 0x9C4/0x10/0x1 will make a 500000 bps */
949 mul = baud / 500000 * 0x9C4;
950 break;
951 default:
952 /* Use uart_get_divisor to get quot for other baud rates */
953 quot = 0;
954 }
955
956 if (!quot)
957 quot = uart_get_divisor(port, baud);
958
959 if ((up->port.uartclk / quot) < (2400 * 16))
960 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_1B;
961 else if ((up->port.uartclk / quot) < (230400 * 16))
962 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_16B;
963 else
964 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_32B;
965
966 fcr |= UART_FCR_HSU_64B_FIFO;
967
968 /*
969 * Ok, we're now changing the port state. Do it with
970 * interrupts disabled.
971 */
972 spin_lock_irqsave(&up->port.lock, flags);
973
974 /* Update the per-port timeout */
975 uart_update_timeout(port, termios->c_cflag, baud);
976
977 up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
978 if (termios->c_iflag & INPCK)
979 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
980 if (termios->c_iflag & (BRKINT | PARMRK))
981 up->port.read_status_mask |= UART_LSR_BI;
982
983 /* Characters to ignore */
984 up->port.ignore_status_mask = 0;
985 if (termios->c_iflag & IGNPAR)
986 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
987 if (termios->c_iflag & IGNBRK) {
988 up->port.ignore_status_mask |= UART_LSR_BI;
989 /*
990 * If we're ignoring parity and break indicators,
991 * ignore overruns too (for real raw support).
992 */
993 if (termios->c_iflag & IGNPAR)
994 up->port.ignore_status_mask |= UART_LSR_OE;
995 }
996
997 /* Ignore all characters if CREAD is not set */
998 if ((termios->c_cflag & CREAD) == 0)
999 up->port.ignore_status_mask |= UART_LSR_DR;
1000
1001 /*
1002 * CTS flow control flag and modem status interrupts, disable
1003 * MSI by default
1004 */
1005 up->ier &= ~UART_IER_MSI;
1006 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
1007 up->ier |= UART_IER_MSI;
1008
1009 serial_out(up, UART_IER, up->ier);
1010
1011 if (termios->c_cflag & CRTSCTS)
1012 up->mcr |= UART_MCR_AFE | UART_MCR_RTS;
1013 else
1014 up->mcr &= ~UART_MCR_AFE;
1015
1016 serial_out(up, UART_LCR, cval | UART_LCR_DLAB); /* set DLAB */
1017 serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */
1018 serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */
1019 serial_out(up, UART_LCR, cval); /* reset DLAB */
1020 serial_out(up, UART_MUL, mul); /* set MUL */
1021 serial_out(up, UART_PS, ps); /* set PS */
1022 up->lcr = cval; /* Save LCR */
1023 serial_hsu_set_mctrl(&up->port, up->port.mctrl);
1024 serial_out(up, UART_FCR, fcr);
1025 spin_unlock_irqrestore(&up->port.lock, flags);
1026}
1027
1028static void
1029serial_hsu_pm(struct uart_port *port, unsigned int state,
1030 unsigned int oldstate)
1031{
1032}
1033
1034static void serial_hsu_release_port(struct uart_port *port)
1035{
1036}
1037
1038static int serial_hsu_request_port(struct uart_port *port)
1039{
1040 return 0;
1041}
1042
1043static void serial_hsu_config_port(struct uart_port *port, int flags)
1044{
1045 struct uart_hsu_port *up =
1046 container_of(port, struct uart_hsu_port, port);
1047 up->port.type = PORT_MFD;
1048}
1049
1050static int
1051serial_hsu_verify_port(struct uart_port *port, struct serial_struct *ser)
1052{
1053 /* We don't want the core code to modify any port params */
1054 return -EINVAL;
1055}
1056
1057static const char *
1058serial_hsu_type(struct uart_port *port)
1059{
1060 struct uart_hsu_port *up =
1061 container_of(port, struct uart_hsu_port, port);
1062 return up->name;
1063}
1064
1065/* Mainly for uart console use */
1066static struct uart_hsu_port *serial_hsu_ports[3];
1067static struct uart_driver serial_hsu_reg;
1068
1069#ifdef CONFIG_SERIAL_MFD_HSU_CONSOLE
1070
1071#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
1072
1073/* Wait for transmitter & holding register to empty */
1074static inline void wait_for_xmitr(struct uart_hsu_port *up)
1075{
1076 unsigned int status, tmout = 1000;
1077
1078 /* Wait up to 1ms for the character to be sent. */
1079 do {
1080 status = serial_in(up, UART_LSR);
1081
1082 if (status & UART_LSR_BI)
1083 up->lsr_break_flag = UART_LSR_BI;
1084
1085 if (--tmout == 0)
1086 break;
1087 udelay(1);
1088 } while (!(status & BOTH_EMPTY));
1089
1090 /* Wait up to 1s for flow control if necessary */
1091 if (up->port.flags & UPF_CONS_FLOW) {
1092 tmout = 1000000;
1093 while (--tmout &&
1094 ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
1095 udelay(1);
1096 }
1097}
1098
1099static void serial_hsu_console_putchar(struct uart_port *port, int ch)
1100{
1101 struct uart_hsu_port *up =
1102 container_of(port, struct uart_hsu_port, port);
1103
1104 wait_for_xmitr(up);
1105 serial_out(up, UART_TX, ch);
1106}
1107
1108/*
1109 * Print a string to the serial port trying not to disturb
1110 * any possible real use of the port...
1111 *
1112 * The console_lock must be held when we get here.
1113 */
1114static void
1115serial_hsu_console_write(struct console *co, const char *s, unsigned int count)
1116{
1117 struct uart_hsu_port *up = serial_hsu_ports[co->index];
1118 unsigned long flags;
1119 unsigned int ier;
1120 int locked = 1;
1121
1122 touch_nmi_watchdog();
1123
1124 local_irq_save(flags);
1125 if (up->port.sysrq)
1126 locked = 0;
1127 else if (oops_in_progress) {
1128 locked = spin_trylock(&up->port.lock);
1129 } else
1130 spin_lock(&up->port.lock);
1131
1132 /* First save the IER then disable the interrupts */
1133 ier = serial_in(up, UART_IER);
1134 serial_out(up, UART_IER, 0);
1135
1136 uart_console_write(&up->port, s, count, serial_hsu_console_putchar);
1137
1138 /*
1139 * Finally, wait for transmitter to become empty
1140 * and restore the IER
1141 */
1142 wait_for_xmitr(up);
1143 serial_out(up, UART_IER, ier);
1144
1145 if (locked)
1146 spin_unlock(&up->port.lock);
1147 local_irq_restore(flags);
1148}
1149
1150static struct console serial_hsu_console;
1151
1152static int __init
1153serial_hsu_console_setup(struct console *co, char *options)
1154{
1155 struct uart_hsu_port *up;
1156 int baud = 115200;
1157 int bits = 8;
1158 int parity = 'n';
1159 int flow = 'n';
1160
1161 if (co->index == -1 || co->index >= serial_hsu_reg.nr)
1162 co->index = 0;
1163 up = serial_hsu_ports[co->index];
1164 if (!up)
1165 return -ENODEV;
1166
1167 if (options)
1168 uart_parse_options(options, &baud, &parity, &bits, &flow);
1169
1170 return uart_set_options(&up->port, co, baud, parity, bits, flow);
1171}
1172
1173static struct console serial_hsu_console = {
1174 .name = "ttyMFD",
1175 .write = serial_hsu_console_write,
1176 .device = uart_console_device,
1177 .setup = serial_hsu_console_setup,
1178 .flags = CON_PRINTBUFFER,
1179 .index = -1,
1180 .data = &serial_hsu_reg,
1181};
1182
1183#define SERIAL_HSU_CONSOLE (&serial_hsu_console)
1184#else
1185#define SERIAL_HSU_CONSOLE NULL
1186#endif
1187
1188static struct uart_ops serial_hsu_pops = {
1189 .tx_empty = serial_hsu_tx_empty,
1190 .set_mctrl = serial_hsu_set_mctrl,
1191 .get_mctrl = serial_hsu_get_mctrl,
1192 .stop_tx = serial_hsu_stop_tx,
1193 .start_tx = serial_hsu_start_tx,
1194 .stop_rx = serial_hsu_stop_rx,
1195 .enable_ms = serial_hsu_enable_ms,
1196 .break_ctl = serial_hsu_break_ctl,
1197 .startup = serial_hsu_startup,
1198 .shutdown = serial_hsu_shutdown,
1199 .set_termios = serial_hsu_set_termios,
1200 .pm = serial_hsu_pm,
1201 .type = serial_hsu_type,
1202 .release_port = serial_hsu_release_port,
1203 .request_port = serial_hsu_request_port,
1204 .config_port = serial_hsu_config_port,
1205 .verify_port = serial_hsu_verify_port,
1206};
1207
1208static struct uart_driver serial_hsu_reg = {
1209 .owner = THIS_MODULE,
1210 .driver_name = "MFD serial",
1211 .dev_name = "ttyMFD",
1212 .major = TTY_MAJOR,
1213 .minor = 128,
1214 .nr = 3,
1215 .cons = SERIAL_HSU_CONSOLE,
1216};
1217
1218#ifdef CONFIG_PM
1219static int serial_hsu_suspend(struct pci_dev *pdev, pm_message_t state)
1220{
1221 void *priv = pci_get_drvdata(pdev);
1222 struct uart_hsu_port *up;
1223
1224 /* Make sure this is not the internal dma controller */
1225 if (priv && (pdev->device != 0x081E)) {
1226 up = priv;
1227 uart_suspend_port(&serial_hsu_reg, &up->port);
1228 }
1229
1230 pci_save_state(pdev);
1231 pci_set_power_state(pdev, pci_choose_state(pdev, state));
1232 return 0;
1233}
1234
1235static int serial_hsu_resume(struct pci_dev *pdev)
1236{
1237 void *priv = pci_get_drvdata(pdev);
1238 struct uart_hsu_port *up;
1239 int ret;
1240
1241 pci_set_power_state(pdev, PCI_D0);
1242 pci_restore_state(pdev);
1243
1244 ret = pci_enable_device(pdev);
1245 if (ret)
1246 dev_warn(&pdev->dev,
1247 "HSU: can't re-enable device, try to continue\n");
1248
1249 if (priv && (pdev->device != 0x081E)) {
1250 up = priv;
1251 uart_resume_port(&serial_hsu_reg, &up->port);
1252 }
1253 return 0;
1254}
1255#else
1256#define serial_hsu_suspend NULL
1257#define serial_hsu_resume NULL
1258#endif
1259
1260#ifdef CONFIG_PM_RUNTIME
1261static int serial_hsu_runtime_idle(struct device *dev)
1262{
1263 pm_schedule_suspend(dev, 500);
1264 return -EBUSY;
1265}
1266
1267static int serial_hsu_runtime_suspend(struct device *dev)
1268{
1269 return 0;
1270}
1271
1272static int serial_hsu_runtime_resume(struct device *dev)
1273{
1274 return 0;
1275}
1276#else
1277#define serial_hsu_runtime_idle NULL
1278#define serial_hsu_runtime_suspend NULL
1279#define serial_hsu_runtime_resume NULL
1280#endif
1281
1282static const struct dev_pm_ops serial_hsu_pm_ops = {
1283 .runtime_suspend = serial_hsu_runtime_suspend,
1284 .runtime_resume = serial_hsu_runtime_resume,
1285 .runtime_idle = serial_hsu_runtime_idle,
1286};
1287
1288/* temp global pointer before we settle down on using one or four PCI dev */
1289static struct hsu_port *phsu;
1290
1291static int serial_hsu_probe(struct pci_dev *pdev,
1292 const struct pci_device_id *ent)
1293{
1294 struct uart_hsu_port *uport;
1295 int index, ret;
1296
1297 printk(KERN_INFO "HSU: found PCI Serial controller(ID: %04x:%04x)\n",
1298 pdev->vendor, pdev->device);
1299
1300 switch (pdev->device) {
1301 case 0x081B:
1302 index = 0;
1303 break;
1304 case 0x081C:
1305 index = 1;
1306 break;
1307 case 0x081D:
1308 index = 2;
1309 break;
1310 case 0x081E:
1311 /* internal DMA controller */
1312 index = 3;
1313 break;
1314 default:
1315 dev_err(&pdev->dev, "HSU: out of index!");
1316 return -ENODEV;
1317 }
1318
1319 ret = pci_enable_device(pdev);
1320 if (ret)
1321 return ret;
1322
1323 if (index == 3) {
1324 /* DMA controller */
1325 ret = request_irq(pdev->irq, dma_irq, 0, "hsu_dma", phsu);
1326 if (ret) {
1327 dev_err(&pdev->dev, "can not get IRQ\n");
1328 goto err_disable;
1329 }
1330 pci_set_drvdata(pdev, phsu);
1331 } else {
1332 /* UART port 0~2 */
1333 uport = &phsu->port[index];
1334 uport->port.irq = pdev->irq;
1335 uport->port.dev = &pdev->dev;
1336 uport->dev = &pdev->dev;
1337
1338 ret = request_irq(pdev->irq, port_irq, 0, uport->name, uport);
1339 if (ret) {
1340 dev_err(&pdev->dev, "can not get IRQ\n");
1341 goto err_disable;
1342 }
1343 uart_add_one_port(&serial_hsu_reg, &uport->port);
1344
1345 pci_set_drvdata(pdev, uport);
1346 }
1347
1348 pm_runtime_put_noidle(&pdev->dev);
1349 pm_runtime_allow(&pdev->dev);
1350
1351 return 0;
1352
1353err_disable:
1354 pci_disable_device(pdev);
1355 return ret;
1356}
1357
1358static void hsu_global_init(void)
1359{
1360 struct hsu_port *hsu;
1361 struct uart_hsu_port *uport;
1362 struct hsu_dma_chan *dchan;
1363 int i, ret;
1364
1365 hsu = kzalloc(sizeof(struct hsu_port), GFP_KERNEL);
1366 if (!hsu)
1367 return;
1368
1369 /* Get basic io resource and map it */
1370 hsu->paddr = 0xffa28000;
1371 hsu->iolen = 0x1000;
1372
1373 if (!(request_mem_region(hsu->paddr, hsu->iolen, "HSU global")))
1374 pr_warning("HSU: error in request mem region\n");
1375
1376 hsu->reg = ioremap_nocache((unsigned long)hsu->paddr, hsu->iolen);
1377 if (!hsu->reg) {
1378 pr_err("HSU: error in ioremap\n");
1379 ret = -ENOMEM;
1380 goto err_free_region;
1381 }
1382
1383 /* Initialise the 3 UART ports */
1384 uport = hsu->port;
1385 for (i = 0; i < 3; i++) {
1386 uport->port.type = PORT_MFD;
1387 uport->port.iotype = UPIO_MEM;
1388 uport->port.mapbase = (resource_size_t)hsu->paddr
1389 + HSU_PORT_REG_OFFSET
1390 + i * HSU_PORT_REG_LENGTH;
1391 uport->port.membase = hsu->reg + HSU_PORT_REG_OFFSET
1392 + i * HSU_PORT_REG_LENGTH;
1393
1394 sprintf(uport->name, "hsu_port%d", i);
1395 uport->port.fifosize = 64;
1396 uport->port.ops = &serial_hsu_pops;
1397 uport->port.line = i;
1398 uport->port.flags = UPF_IOREMAP;
1399 /* set the scalable maxim support rate to 2746800 bps */
1400 uport->port.uartclk = 115200 * 24 * 16;
1401
1402 uport->running = 0;
1403 uport->txc = &hsu->chans[i * 2];
1404 uport->rxc = &hsu->chans[i * 2 + 1];
1405
1406 serial_hsu_ports[i] = uport;
1407 uport->index = i;
1408
1409 if (hsu_dma_enable & (1<<i))
1410 uport->use_dma = 1;
1411 else
1412 uport->use_dma = 0;
1413
1414 uport++;
1415 }
1416
1417 /* Initialise 6 dma channels */
1418 dchan = hsu->chans;
1419 for (i = 0; i < 6; i++) {
1420 dchan->id = i;
1421 dchan->dirt = (i & 0x1) ? DMA_FROM_DEVICE : DMA_TO_DEVICE;
1422 dchan->uport = &hsu->port[i/2];
1423 dchan->reg = hsu->reg + HSU_DMA_CHANS_REG_OFFSET +
1424 i * HSU_DMA_CHANS_REG_LENGTH;
1425
1426 dchan++;
1427 }
1428
1429 phsu = hsu;
1430 hsu_debugfs_init(hsu);
1431 return;
1432
1433err_free_region:
1434 release_mem_region(hsu->paddr, hsu->iolen);
1435 kfree(hsu);
1436 return;
1437}
1438
1439static void serial_hsu_remove(struct pci_dev *pdev)
1440{
1441 void *priv = pci_get_drvdata(pdev);
1442 struct uart_hsu_port *up;
1443
1444 if (!priv)
1445 return;
1446
1447 pm_runtime_forbid(&pdev->dev);
1448 pm_runtime_get_noresume(&pdev->dev);
1449
1450 /* For port 0/1/2, priv is the address of uart_hsu_port */
1451 if (pdev->device != 0x081E) {
1452 up = priv;
1453 uart_remove_one_port(&serial_hsu_reg, &up->port);
1454 }
1455
1456 free_irq(pdev->irq, priv);
1457 pci_disable_device(pdev);
1458}
1459
1460/* First 3 are UART ports, and the 4th is the DMA */
1461static const struct pci_device_id pci_ids[] = {
1462 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081B) },
1463 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081C) },
1464 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081D) },
1465 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081E) },
1466 {},
1467};
1468
1469static struct pci_driver hsu_pci_driver = {
1470 .name = "HSU serial",
1471 .id_table = pci_ids,
1472 .probe = serial_hsu_probe,
1473 .remove = serial_hsu_remove,
1474 .suspend = serial_hsu_suspend,
1475 .resume = serial_hsu_resume,
1476 .driver = {
1477 .pm = &serial_hsu_pm_ops,
1478 },
1479};
1480
1481static int __init hsu_pci_init(void)
1482{
1483 int ret;
1484
1485 hsu_global_init();
1486
1487 ret = uart_register_driver(&serial_hsu_reg);
1488 if (ret)
1489 return ret;
1490
1491 return pci_register_driver(&hsu_pci_driver);
1492}
1493
1494static void __exit hsu_pci_exit(void)
1495{
1496 pci_unregister_driver(&hsu_pci_driver);
1497 uart_unregister_driver(&serial_hsu_reg);
1498
1499 hsu_debugfs_remove(phsu);
1500
1501 kfree(phsu);
1502}
1503
1504module_init(hsu_pci_init);
1505module_exit(hsu_pci_exit);
1506
1507MODULE_LICENSE("GPL v2");
1508MODULE_DEVICE_TABLE(pci, pci_ids);