Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Driver for most of the SPI EEPROMs, such as Atmel AT25 models
4 * and Cypress FRAMs FM25 models.
5 *
6 * Copyright (C) 2006 David Brownell
7 */
8
9#include <linux/bits.h>
10#include <linux/delay.h>
11#include <linux/device.h>
12#include <linux/kernel.h>
13#include <linux/module.h>
14#include <linux/property.h>
15#include <linux/sched.h>
16#include <linux/slab.h>
17
18#include <linux/spi/eeprom.h>
19#include <linux/spi/spi.h>
20
21#include <linux/nvmem-provider.h>
22
23/*
24 * NOTE: this is an *EEPROM* driver. The vagaries of product naming
25 * mean that some AT25 products are EEPROMs, and others are FLASH.
26 * Handle FLASH chips with the drivers/mtd/devices/m25p80.c driver,
27 * not this one!
28 *
29 * EEPROMs that can be used with this driver include, for example:
30 * AT25M02, AT25128B
31 */
32
33#define FM25_SN_LEN 8 /* serial number length */
34#define EE_MAXADDRLEN 3 /* 24 bit addresses, up to 2 MBytes */
35
36struct at25_data {
37 struct spi_eeprom chip;
38 struct spi_device *spi;
39 struct mutex lock;
40 unsigned addrlen;
41 struct nvmem_config nvmem_config;
42 struct nvmem_device *nvmem;
43 u8 sernum[FM25_SN_LEN];
44 u8 command[EE_MAXADDRLEN + 1];
45};
46
47#define AT25_WREN 0x06 /* latch the write enable */
48#define AT25_WRDI 0x04 /* reset the write enable */
49#define AT25_RDSR 0x05 /* read status register */
50#define AT25_WRSR 0x01 /* write status register */
51#define AT25_READ 0x03 /* read byte(s) */
52#define AT25_WRITE 0x02 /* write byte(s)/sector */
53#define FM25_SLEEP 0xb9 /* enter sleep mode */
54#define FM25_RDID 0x9f /* read device ID */
55#define FM25_RDSN 0xc3 /* read S/N */
56
57#define AT25_SR_nRDY 0x01 /* nRDY = write-in-progress */
58#define AT25_SR_WEN 0x02 /* write enable (latched) */
59#define AT25_SR_BP0 0x04 /* BP for software writeprotect */
60#define AT25_SR_BP1 0x08
61#define AT25_SR_WPEN 0x80 /* writeprotect enable */
62
63#define AT25_INSTR_BIT3 0x08 /* additional address bit in instr */
64
65#define FM25_ID_LEN 9 /* ID length */
66
67/*
68 * Specs often allow 5ms for a page write, sometimes 20ms;
69 * it's important to recover from write timeouts.
70 */
71#define EE_TIMEOUT 25
72
73/*-------------------------------------------------------------------------*/
74
75#define io_limit PAGE_SIZE /* bytes */
76
77static int at25_ee_read(void *priv, unsigned int offset,
78 void *val, size_t count)
79{
80 struct at25_data *at25 = priv;
81 char *buf = val;
82 size_t max_chunk = spi_max_transfer_size(at25->spi);
83 unsigned int msg_offset = offset;
84 size_t bytes_left = count;
85 size_t segment;
86 u8 *cp;
87 ssize_t status;
88 struct spi_transfer t[2];
89 struct spi_message m;
90 u8 instr;
91
92 if (unlikely(offset >= at25->chip.byte_len))
93 return -EINVAL;
94 if ((offset + count) > at25->chip.byte_len)
95 count = at25->chip.byte_len - offset;
96 if (unlikely(!count))
97 return -EINVAL;
98
99 do {
100 segment = min(bytes_left, max_chunk);
101 cp = at25->command;
102
103 instr = AT25_READ;
104 if (at25->chip.flags & EE_INSTR_BIT3_IS_ADDR)
105 if (msg_offset >= BIT(at25->addrlen * 8))
106 instr |= AT25_INSTR_BIT3;
107
108 mutex_lock(&at25->lock);
109
110 *cp++ = instr;
111
112 /* 8/16/24-bit address is written MSB first */
113 switch (at25->addrlen) {
114 default: /* case 3 */
115 *cp++ = msg_offset >> 16;
116 fallthrough;
117 case 2:
118 *cp++ = msg_offset >> 8;
119 fallthrough;
120 case 1:
121 case 0: /* can't happen: for better code generation */
122 *cp++ = msg_offset >> 0;
123 }
124
125 spi_message_init(&m);
126 memset(t, 0, sizeof(t));
127
128 t[0].tx_buf = at25->command;
129 t[0].len = at25->addrlen + 1;
130 spi_message_add_tail(&t[0], &m);
131
132 t[1].rx_buf = buf;
133 t[1].len = segment;
134 spi_message_add_tail(&t[1], &m);
135
136 status = spi_sync(at25->spi, &m);
137
138 mutex_unlock(&at25->lock);
139
140 if (status)
141 return status;
142
143 msg_offset += segment;
144 buf += segment;
145 bytes_left -= segment;
146 } while (bytes_left > 0);
147
148 dev_dbg(&at25->spi->dev, "read %zu bytes at %d\n",
149 count, offset);
150 return 0;
151}
152
153/* Read extra registers as ID or serial number */
154static int fm25_aux_read(struct at25_data *at25, u8 *buf, uint8_t command,
155 int len)
156{
157 int status;
158 struct spi_transfer t[2];
159 struct spi_message m;
160
161 spi_message_init(&m);
162 memset(t, 0, sizeof(t));
163
164 t[0].tx_buf = at25->command;
165 t[0].len = 1;
166 spi_message_add_tail(&t[0], &m);
167
168 t[1].rx_buf = buf;
169 t[1].len = len;
170 spi_message_add_tail(&t[1], &m);
171
172 mutex_lock(&at25->lock);
173
174 at25->command[0] = command;
175
176 status = spi_sync(at25->spi, &m);
177 dev_dbg(&at25->spi->dev, "read %d aux bytes --> %d\n", len, status);
178
179 mutex_unlock(&at25->lock);
180 return status;
181}
182
183static ssize_t sernum_show(struct device *dev, struct device_attribute *attr, char *buf)
184{
185 struct at25_data *at25;
186
187 at25 = dev_get_drvdata(dev);
188 return sysfs_emit(buf, "%*ph\n", (int)sizeof(at25->sernum), at25->sernum);
189}
190static DEVICE_ATTR_RO(sernum);
191
192static struct attribute *sernum_attrs[] = {
193 &dev_attr_sernum.attr,
194 NULL,
195};
196ATTRIBUTE_GROUPS(sernum);
197
198static int at25_ee_write(void *priv, unsigned int off, void *val, size_t count)
199{
200 struct at25_data *at25 = priv;
201 size_t maxsz = spi_max_transfer_size(at25->spi);
202 const char *buf = val;
203 int status = 0;
204 unsigned buf_size;
205 u8 *bounce;
206
207 if (unlikely(off >= at25->chip.byte_len))
208 return -EFBIG;
209 if ((off + count) > at25->chip.byte_len)
210 count = at25->chip.byte_len - off;
211 if (unlikely(!count))
212 return -EINVAL;
213
214 /* Temp buffer starts with command and address */
215 buf_size = at25->chip.page_size;
216 if (buf_size > io_limit)
217 buf_size = io_limit;
218 bounce = kmalloc(buf_size + at25->addrlen + 1, GFP_KERNEL);
219 if (!bounce)
220 return -ENOMEM;
221
222 /*
223 * For write, rollover is within the page ... so we write at
224 * most one page, then manually roll over to the next page.
225 */
226 mutex_lock(&at25->lock);
227 do {
228 unsigned long timeout, retries;
229 unsigned segment;
230 unsigned offset = off;
231 u8 *cp = bounce;
232 int sr;
233 u8 instr;
234
235 *cp = AT25_WREN;
236 status = spi_write(at25->spi, cp, 1);
237 if (status < 0) {
238 dev_dbg(&at25->spi->dev, "WREN --> %d\n", status);
239 break;
240 }
241
242 instr = AT25_WRITE;
243 if (at25->chip.flags & EE_INSTR_BIT3_IS_ADDR)
244 if (offset >= BIT(at25->addrlen * 8))
245 instr |= AT25_INSTR_BIT3;
246 *cp++ = instr;
247
248 /* 8/16/24-bit address is written MSB first */
249 switch (at25->addrlen) {
250 default: /* case 3 */
251 *cp++ = offset >> 16;
252 fallthrough;
253 case 2:
254 *cp++ = offset >> 8;
255 fallthrough;
256 case 1:
257 case 0: /* can't happen: for better code generation */
258 *cp++ = offset >> 0;
259 }
260
261 /* Write as much of a page as we can */
262 segment = buf_size - (offset % buf_size);
263 if (segment > count)
264 segment = count;
265 if (segment > maxsz)
266 segment = maxsz;
267 memcpy(cp, buf, segment);
268 status = spi_write(at25->spi, bounce,
269 segment + at25->addrlen + 1);
270 dev_dbg(&at25->spi->dev, "write %u bytes at %u --> %d\n",
271 segment, offset, status);
272 if (status < 0)
273 break;
274
275 /*
276 * REVISIT this should detect (or prevent) failed writes
277 * to read-only sections of the EEPROM...
278 */
279
280 /* Wait for non-busy status */
281 timeout = jiffies + msecs_to_jiffies(EE_TIMEOUT);
282 retries = 0;
283 do {
284
285 sr = spi_w8r8(at25->spi, AT25_RDSR);
286 if (sr < 0 || (sr & AT25_SR_nRDY)) {
287 dev_dbg(&at25->spi->dev,
288 "rdsr --> %d (%02x)\n", sr, sr);
289 /* at HZ=100, this is sloooow */
290 msleep(1);
291 continue;
292 }
293 if (!(sr & AT25_SR_nRDY))
294 break;
295 } while (retries++ < 3 || time_before_eq(jiffies, timeout));
296
297 if ((sr < 0) || (sr & AT25_SR_nRDY)) {
298 dev_err(&at25->spi->dev,
299 "write %u bytes offset %u, timeout after %u msecs\n",
300 segment, offset,
301 jiffies_to_msecs(jiffies -
302 (timeout - EE_TIMEOUT)));
303 status = -ETIMEDOUT;
304 break;
305 }
306
307 off += segment;
308 buf += segment;
309 count -= segment;
310
311 } while (count > 0);
312
313 mutex_unlock(&at25->lock);
314
315 kfree(bounce);
316 return status;
317}
318
319/*-------------------------------------------------------------------------*/
320
321static int at25_fw_to_chip(struct device *dev, struct spi_eeprom *chip)
322{
323 u32 val;
324 int err;
325
326 strscpy(chip->name, "at25", sizeof(chip->name));
327
328 err = device_property_read_u32(dev, "size", &val);
329 if (err)
330 err = device_property_read_u32(dev, "at25,byte-len", &val);
331 if (err) {
332 dev_err(dev, "Error: missing \"size\" property\n");
333 return err;
334 }
335 chip->byte_len = val;
336
337 err = device_property_read_u32(dev, "pagesize", &val);
338 if (err)
339 err = device_property_read_u32(dev, "at25,page-size", &val);
340 if (err) {
341 dev_err(dev, "Error: missing \"pagesize\" property\n");
342 return err;
343 }
344 chip->page_size = val;
345
346 err = device_property_read_u32(dev, "address-width", &val);
347 if (err) {
348 err = device_property_read_u32(dev, "at25,addr-mode", &val);
349 if (err) {
350 dev_err(dev, "Error: missing \"address-width\" property\n");
351 return err;
352 }
353 chip->flags = (u16)val;
354 } else {
355 switch (val) {
356 case 9:
357 chip->flags |= EE_INSTR_BIT3_IS_ADDR;
358 fallthrough;
359 case 8:
360 chip->flags |= EE_ADDR1;
361 break;
362 case 16:
363 chip->flags |= EE_ADDR2;
364 break;
365 case 24:
366 chip->flags |= EE_ADDR3;
367 break;
368 default:
369 dev_err(dev,
370 "Error: bad \"address-width\" property: %u\n",
371 val);
372 return -ENODEV;
373 }
374 if (device_property_present(dev, "read-only"))
375 chip->flags |= EE_READONLY;
376 }
377 return 0;
378}
379
380static int at25_fram_to_chip(struct device *dev, struct spi_eeprom *chip)
381{
382 struct at25_data *at25 = container_of(chip, struct at25_data, chip);
383 u8 sernum[FM25_SN_LEN];
384 u8 id[FM25_ID_LEN];
385 int i;
386
387 strscpy(chip->name, "fm25", sizeof(chip->name));
388
389 /* Get ID of chip */
390 fm25_aux_read(at25, id, FM25_RDID, FM25_ID_LEN);
391 if (id[6] != 0xc2) {
392 dev_err(dev, "Error: no Cypress FRAM (id %02x)\n", id[6]);
393 return -ENODEV;
394 }
395 /* Set size found in ID */
396 if (id[7] < 0x21 || id[7] > 0x26) {
397 dev_err(dev, "Error: unsupported size (id %02x)\n", id[7]);
398 return -ENODEV;
399 }
400
401 chip->byte_len = BIT(id[7] - 0x21 + 4) * 1024;
402 if (chip->byte_len > 64 * 1024)
403 chip->flags |= EE_ADDR3;
404 else
405 chip->flags |= EE_ADDR2;
406
407 if (id[8]) {
408 fm25_aux_read(at25, sernum, FM25_RDSN, FM25_SN_LEN);
409 /* Swap byte order */
410 for (i = 0; i < FM25_SN_LEN; i++)
411 at25->sernum[i] = sernum[FM25_SN_LEN - 1 - i];
412 }
413
414 chip->page_size = PAGE_SIZE;
415 return 0;
416}
417
418static const struct of_device_id at25_of_match[] = {
419 { .compatible = "atmel,at25" },
420 { .compatible = "cypress,fm25" },
421 { }
422};
423MODULE_DEVICE_TABLE(of, at25_of_match);
424
425static const struct spi_device_id at25_spi_ids[] = {
426 { .name = "at25" },
427 { .name = "fm25" },
428 { }
429};
430MODULE_DEVICE_TABLE(spi, at25_spi_ids);
431
432static int at25_probe(struct spi_device *spi)
433{
434 struct at25_data *at25 = NULL;
435 int err;
436 int sr;
437 struct spi_eeprom *pdata;
438 bool is_fram;
439
440 /*
441 * Ping the chip ... the status register is pretty portable,
442 * unlike probing manufacturer IDs. We do expect that system
443 * firmware didn't write it in the past few milliseconds!
444 */
445 sr = spi_w8r8(spi, AT25_RDSR);
446 if (sr < 0 || sr & AT25_SR_nRDY) {
447 dev_dbg(&spi->dev, "rdsr --> %d (%02x)\n", sr, sr);
448 return -ENXIO;
449 }
450
451 at25 = devm_kzalloc(&spi->dev, sizeof(*at25), GFP_KERNEL);
452 if (!at25)
453 return -ENOMEM;
454
455 mutex_init(&at25->lock);
456 at25->spi = spi;
457 spi_set_drvdata(spi, at25);
458
459 is_fram = fwnode_device_is_compatible(dev_fwnode(&spi->dev), "cypress,fm25");
460
461 /* Chip description */
462 pdata = dev_get_platdata(&spi->dev);
463 if (pdata) {
464 at25->chip = *pdata;
465 } else {
466 if (is_fram)
467 err = at25_fram_to_chip(&spi->dev, &at25->chip);
468 else
469 err = at25_fw_to_chip(&spi->dev, &at25->chip);
470 if (err)
471 return err;
472 }
473
474 /* For now we only support 8/16/24 bit addressing */
475 if (at25->chip.flags & EE_ADDR1)
476 at25->addrlen = 1;
477 else if (at25->chip.flags & EE_ADDR2)
478 at25->addrlen = 2;
479 else if (at25->chip.flags & EE_ADDR3)
480 at25->addrlen = 3;
481 else {
482 dev_dbg(&spi->dev, "unsupported address type\n");
483 return -EINVAL;
484 }
485
486 at25->nvmem_config.type = is_fram ? NVMEM_TYPE_FRAM : NVMEM_TYPE_EEPROM;
487 at25->nvmem_config.name = dev_name(&spi->dev);
488 at25->nvmem_config.dev = &spi->dev;
489 at25->nvmem_config.read_only = at25->chip.flags & EE_READONLY;
490 at25->nvmem_config.root_only = true;
491 at25->nvmem_config.owner = THIS_MODULE;
492 at25->nvmem_config.compat = true;
493 at25->nvmem_config.base_dev = &spi->dev;
494 at25->nvmem_config.reg_read = at25_ee_read;
495 at25->nvmem_config.reg_write = at25_ee_write;
496 at25->nvmem_config.priv = at25;
497 at25->nvmem_config.stride = 1;
498 at25->nvmem_config.word_size = 1;
499 at25->nvmem_config.size = at25->chip.byte_len;
500
501 at25->nvmem = devm_nvmem_register(&spi->dev, &at25->nvmem_config);
502 if (IS_ERR(at25->nvmem))
503 return PTR_ERR(at25->nvmem);
504
505 dev_info(&spi->dev, "%d %s %s %s%s, pagesize %u\n",
506 (at25->chip.byte_len < 1024) ?
507 at25->chip.byte_len : (at25->chip.byte_len / 1024),
508 (at25->chip.byte_len < 1024) ? "Byte" : "KByte",
509 at25->chip.name, is_fram ? "fram" : "eeprom",
510 (at25->chip.flags & EE_READONLY) ? " (readonly)" : "",
511 at25->chip.page_size);
512 return 0;
513}
514
515/*-------------------------------------------------------------------------*/
516
517static struct spi_driver at25_driver = {
518 .driver = {
519 .name = "at25",
520 .of_match_table = at25_of_match,
521 .dev_groups = sernum_groups,
522 },
523 .probe = at25_probe,
524 .id_table = at25_spi_ids,
525};
526
527module_spi_driver(at25_driver);
528
529MODULE_DESCRIPTION("Driver for most SPI EEPROMs");
530MODULE_AUTHOR("David Brownell");
531MODULE_LICENSE("GPL");
532MODULE_ALIAS("spi:at25");
1/*
2 * at25.c -- support most SPI EEPROMs, such as Atmel AT25 models
3 *
4 * Copyright (C) 2006 David Brownell
5 *
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2 of the License, or
9 * (at your option) any later version.
10 */
11
12#include <linux/kernel.h>
13#include <linux/module.h>
14#include <linux/slab.h>
15#include <linux/delay.h>
16#include <linux/device.h>
17#include <linux/sched.h>
18
19#include <linux/spi/spi.h>
20#include <linux/spi/eeprom.h>
21#include <linux/of.h>
22
23/*
24 * NOTE: this is an *EEPROM* driver. The vagaries of product naming
25 * mean that some AT25 products are EEPROMs, and others are FLASH.
26 * Handle FLASH chips with the drivers/mtd/devices/m25p80.c driver,
27 * not this one!
28 */
29
30struct at25_data {
31 struct spi_device *spi;
32 struct memory_accessor mem;
33 struct mutex lock;
34 struct spi_eeprom chip;
35 struct bin_attribute bin;
36 unsigned addrlen;
37};
38
39#define AT25_WREN 0x06 /* latch the write enable */
40#define AT25_WRDI 0x04 /* reset the write enable */
41#define AT25_RDSR 0x05 /* read status register */
42#define AT25_WRSR 0x01 /* write status register */
43#define AT25_READ 0x03 /* read byte(s) */
44#define AT25_WRITE 0x02 /* write byte(s)/sector */
45
46#define AT25_SR_nRDY 0x01 /* nRDY = write-in-progress */
47#define AT25_SR_WEN 0x02 /* write enable (latched) */
48#define AT25_SR_BP0 0x04 /* BP for software writeprotect */
49#define AT25_SR_BP1 0x08
50#define AT25_SR_WPEN 0x80 /* writeprotect enable */
51
52#define AT25_INSTR_BIT3 0x08 /* Additional address bit in instr */
53
54#define EE_MAXADDRLEN 3 /* 24 bit addresses, up to 2 MBytes */
55
56/* Specs often allow 5 msec for a page write, sometimes 20 msec;
57 * it's important to recover from write timeouts.
58 */
59#define EE_TIMEOUT 25
60
61/*-------------------------------------------------------------------------*/
62
63#define io_limit PAGE_SIZE /* bytes */
64
65static ssize_t
66at25_ee_read(
67 struct at25_data *at25,
68 char *buf,
69 unsigned offset,
70 size_t count
71)
72{
73 u8 command[EE_MAXADDRLEN + 1];
74 u8 *cp;
75 ssize_t status;
76 struct spi_transfer t[2];
77 struct spi_message m;
78 u8 instr;
79
80 if (unlikely(offset >= at25->bin.size))
81 return 0;
82 if ((offset + count) > at25->bin.size)
83 count = at25->bin.size - offset;
84 if (unlikely(!count))
85 return count;
86
87 cp = command;
88
89 instr = AT25_READ;
90 if (at25->chip.flags & EE_INSTR_BIT3_IS_ADDR)
91 if (offset >= (1U << (at25->addrlen * 8)))
92 instr |= AT25_INSTR_BIT3;
93 *cp++ = instr;
94
95 /* 8/16/24-bit address is written MSB first */
96 switch (at25->addrlen) {
97 default: /* case 3 */
98 *cp++ = offset >> 16;
99 case 2:
100 *cp++ = offset >> 8;
101 case 1:
102 case 0: /* can't happen: for better codegen */
103 *cp++ = offset >> 0;
104 }
105
106 spi_message_init(&m);
107 memset(t, 0, sizeof t);
108
109 t[0].tx_buf = command;
110 t[0].len = at25->addrlen + 1;
111 spi_message_add_tail(&t[0], &m);
112
113 t[1].rx_buf = buf;
114 t[1].len = count;
115 spi_message_add_tail(&t[1], &m);
116
117 mutex_lock(&at25->lock);
118
119 /* Read it all at once.
120 *
121 * REVISIT that's potentially a problem with large chips, if
122 * other devices on the bus need to be accessed regularly or
123 * this chip is clocked very slowly
124 */
125 status = spi_sync(at25->spi, &m);
126 dev_dbg(&at25->spi->dev,
127 "read %Zd bytes at %d --> %d\n",
128 count, offset, (int) status);
129
130 mutex_unlock(&at25->lock);
131 return status ? status : count;
132}
133
134static ssize_t
135at25_bin_read(struct file *filp, struct kobject *kobj,
136 struct bin_attribute *bin_attr,
137 char *buf, loff_t off, size_t count)
138{
139 struct device *dev;
140 struct at25_data *at25;
141
142 dev = container_of(kobj, struct device, kobj);
143 at25 = dev_get_drvdata(dev);
144
145 return at25_ee_read(at25, buf, off, count);
146}
147
148
149static ssize_t
150at25_ee_write(struct at25_data *at25, const char *buf, loff_t off,
151 size_t count)
152{
153 ssize_t status = 0;
154 unsigned written = 0;
155 unsigned buf_size;
156 u8 *bounce;
157
158 if (unlikely(off >= at25->bin.size))
159 return -EFBIG;
160 if ((off + count) > at25->bin.size)
161 count = at25->bin.size - off;
162 if (unlikely(!count))
163 return count;
164
165 /* Temp buffer starts with command and address */
166 buf_size = at25->chip.page_size;
167 if (buf_size > io_limit)
168 buf_size = io_limit;
169 bounce = kmalloc(buf_size + at25->addrlen + 1, GFP_KERNEL);
170 if (!bounce)
171 return -ENOMEM;
172
173 /* For write, rollover is within the page ... so we write at
174 * most one page, then manually roll over to the next page.
175 */
176 mutex_lock(&at25->lock);
177 do {
178 unsigned long timeout, retries;
179 unsigned segment;
180 unsigned offset = (unsigned) off;
181 u8 *cp = bounce;
182 int sr;
183 u8 instr;
184
185 *cp = AT25_WREN;
186 status = spi_write(at25->spi, cp, 1);
187 if (status < 0) {
188 dev_dbg(&at25->spi->dev, "WREN --> %d\n",
189 (int) status);
190 break;
191 }
192
193 instr = AT25_WRITE;
194 if (at25->chip.flags & EE_INSTR_BIT3_IS_ADDR)
195 if (offset >= (1U << (at25->addrlen * 8)))
196 instr |= AT25_INSTR_BIT3;
197 *cp++ = instr;
198
199 /* 8/16/24-bit address is written MSB first */
200 switch (at25->addrlen) {
201 default: /* case 3 */
202 *cp++ = offset >> 16;
203 case 2:
204 *cp++ = offset >> 8;
205 case 1:
206 case 0: /* can't happen: for better codegen */
207 *cp++ = offset >> 0;
208 }
209
210 /* Write as much of a page as we can */
211 segment = buf_size - (offset % buf_size);
212 if (segment > count)
213 segment = count;
214 memcpy(cp, buf, segment);
215 status = spi_write(at25->spi, bounce,
216 segment + at25->addrlen + 1);
217 dev_dbg(&at25->spi->dev,
218 "write %u bytes at %u --> %d\n",
219 segment, offset, (int) status);
220 if (status < 0)
221 break;
222
223 /* REVISIT this should detect (or prevent) failed writes
224 * to readonly sections of the EEPROM...
225 */
226
227 /* Wait for non-busy status */
228 timeout = jiffies + msecs_to_jiffies(EE_TIMEOUT);
229 retries = 0;
230 do {
231
232 sr = spi_w8r8(at25->spi, AT25_RDSR);
233 if (sr < 0 || (sr & AT25_SR_nRDY)) {
234 dev_dbg(&at25->spi->dev,
235 "rdsr --> %d (%02x)\n", sr, sr);
236 /* at HZ=100, this is sloooow */
237 msleep(1);
238 continue;
239 }
240 if (!(sr & AT25_SR_nRDY))
241 break;
242 } while (retries++ < 3 || time_before_eq(jiffies, timeout));
243
244 if ((sr < 0) || (sr & AT25_SR_nRDY)) {
245 dev_err(&at25->spi->dev,
246 "write %d bytes offset %d, "
247 "timeout after %u msecs\n",
248 segment, offset,
249 jiffies_to_msecs(jiffies -
250 (timeout - EE_TIMEOUT)));
251 status = -ETIMEDOUT;
252 break;
253 }
254
255 off += segment;
256 buf += segment;
257 count -= segment;
258 written += segment;
259
260 } while (count > 0);
261
262 mutex_unlock(&at25->lock);
263
264 kfree(bounce);
265 return written ? written : status;
266}
267
268static ssize_t
269at25_bin_write(struct file *filp, struct kobject *kobj,
270 struct bin_attribute *bin_attr,
271 char *buf, loff_t off, size_t count)
272{
273 struct device *dev;
274 struct at25_data *at25;
275
276 dev = container_of(kobj, struct device, kobj);
277 at25 = dev_get_drvdata(dev);
278
279 return at25_ee_write(at25, buf, off, count);
280}
281
282/*-------------------------------------------------------------------------*/
283
284/* Let in-kernel code access the eeprom data. */
285
286static ssize_t at25_mem_read(struct memory_accessor *mem, char *buf,
287 off_t offset, size_t count)
288{
289 struct at25_data *at25 = container_of(mem, struct at25_data, mem);
290
291 return at25_ee_read(at25, buf, offset, count);
292}
293
294static ssize_t at25_mem_write(struct memory_accessor *mem, const char *buf,
295 off_t offset, size_t count)
296{
297 struct at25_data *at25 = container_of(mem, struct at25_data, mem);
298
299 return at25_ee_write(at25, buf, offset, count);
300}
301
302/*-------------------------------------------------------------------------*/
303
304static int at25_np_to_chip(struct device *dev,
305 struct device_node *np,
306 struct spi_eeprom *chip)
307{
308 u32 val;
309
310 memset(chip, 0, sizeof(*chip));
311 strncpy(chip->name, np->name, sizeof(chip->name));
312
313 if (of_property_read_u32(np, "size", &val) == 0 ||
314 of_property_read_u32(np, "at25,byte-len", &val) == 0) {
315 chip->byte_len = val;
316 } else {
317 dev_err(dev, "Error: missing \"size\" property\n");
318 return -ENODEV;
319 }
320
321 if (of_property_read_u32(np, "pagesize", &val) == 0 ||
322 of_property_read_u32(np, "at25,page-size", &val) == 0) {
323 chip->page_size = (u16)val;
324 } else {
325 dev_err(dev, "Error: missing \"pagesize\" property\n");
326 return -ENODEV;
327 }
328
329 if (of_property_read_u32(np, "at25,addr-mode", &val) == 0) {
330 chip->flags = (u16)val;
331 } else {
332 if (of_property_read_u32(np, "address-width", &val)) {
333 dev_err(dev,
334 "Error: missing \"address-width\" property\n");
335 return -ENODEV;
336 }
337 switch (val) {
338 case 8:
339 chip->flags |= EE_ADDR1;
340 break;
341 case 16:
342 chip->flags |= EE_ADDR2;
343 break;
344 case 24:
345 chip->flags |= EE_ADDR3;
346 break;
347 default:
348 dev_err(dev,
349 "Error: bad \"address-width\" property: %u\n",
350 val);
351 return -ENODEV;
352 }
353 if (of_find_property(np, "read-only", NULL))
354 chip->flags |= EE_READONLY;
355 }
356 return 0;
357}
358
359static int at25_probe(struct spi_device *spi)
360{
361 struct at25_data *at25 = NULL;
362 struct spi_eeprom chip;
363 struct device_node *np = spi->dev.of_node;
364 int err;
365 int sr;
366 int addrlen;
367
368 /* Chip description */
369 if (!spi->dev.platform_data) {
370 if (np) {
371 err = at25_np_to_chip(&spi->dev, np, &chip);
372 if (err)
373 return err;
374 } else {
375 dev_err(&spi->dev, "Error: no chip description\n");
376 return -ENODEV;
377 }
378 } else
379 chip = *(struct spi_eeprom *)spi->dev.platform_data;
380
381 /* For now we only support 8/16/24 bit addressing */
382 if (chip.flags & EE_ADDR1)
383 addrlen = 1;
384 else if (chip.flags & EE_ADDR2)
385 addrlen = 2;
386 else if (chip.flags & EE_ADDR3)
387 addrlen = 3;
388 else {
389 dev_dbg(&spi->dev, "unsupported address type\n");
390 return -EINVAL;
391 }
392
393 /* Ping the chip ... the status register is pretty portable,
394 * unlike probing manufacturer IDs. We do expect that system
395 * firmware didn't write it in the past few milliseconds!
396 */
397 sr = spi_w8r8(spi, AT25_RDSR);
398 if (sr < 0 || sr & AT25_SR_nRDY) {
399 dev_dbg(&spi->dev, "rdsr --> %d (%02x)\n", sr, sr);
400 return -ENXIO;
401 }
402
403 at25 = devm_kzalloc(&spi->dev, sizeof(struct at25_data), GFP_KERNEL);
404 if (!at25)
405 return -ENOMEM;
406
407 mutex_init(&at25->lock);
408 at25->chip = chip;
409 at25->spi = spi_dev_get(spi);
410 spi_set_drvdata(spi, at25);
411 at25->addrlen = addrlen;
412
413 /* Export the EEPROM bytes through sysfs, since that's convenient.
414 * And maybe to other kernel code; it might hold a board's Ethernet
415 * address, or board-specific calibration data generated on the
416 * manufacturing floor.
417 *
418 * Default to root-only access to the data; EEPROMs often hold data
419 * that's sensitive for read and/or write, like ethernet addresses,
420 * security codes, board-specific manufacturing calibrations, etc.
421 */
422 sysfs_bin_attr_init(&at25->bin);
423 at25->bin.attr.name = "eeprom";
424 at25->bin.attr.mode = S_IRUSR;
425 at25->bin.read = at25_bin_read;
426 at25->mem.read = at25_mem_read;
427
428 at25->bin.size = at25->chip.byte_len;
429 if (!(chip.flags & EE_READONLY)) {
430 at25->bin.write = at25_bin_write;
431 at25->bin.attr.mode |= S_IWUSR;
432 at25->mem.write = at25_mem_write;
433 }
434
435 err = sysfs_create_bin_file(&spi->dev.kobj, &at25->bin);
436 if (err)
437 return err;
438
439 if (chip.setup)
440 chip.setup(&at25->mem, chip.context);
441
442 dev_info(&spi->dev, "%Zd %s %s eeprom%s, pagesize %u\n",
443 (at25->bin.size < 1024)
444 ? at25->bin.size
445 : (at25->bin.size / 1024),
446 (at25->bin.size < 1024) ? "Byte" : "KByte",
447 at25->chip.name,
448 (chip.flags & EE_READONLY) ? " (readonly)" : "",
449 at25->chip.page_size);
450 return 0;
451}
452
453static int at25_remove(struct spi_device *spi)
454{
455 struct at25_data *at25;
456
457 at25 = spi_get_drvdata(spi);
458 sysfs_remove_bin_file(&spi->dev.kobj, &at25->bin);
459 return 0;
460}
461
462/*-------------------------------------------------------------------------*/
463
464static const struct of_device_id at25_of_match[] = {
465 { .compatible = "atmel,at25", },
466 { }
467};
468MODULE_DEVICE_TABLE(of, at25_of_match);
469
470static struct spi_driver at25_driver = {
471 .driver = {
472 .name = "at25",
473 .owner = THIS_MODULE,
474 .of_match_table = at25_of_match,
475 },
476 .probe = at25_probe,
477 .remove = at25_remove,
478};
479
480module_spi_driver(at25_driver);
481
482MODULE_DESCRIPTION("Driver for most SPI EEPROMs");
483MODULE_AUTHOR("David Brownell");
484MODULE_LICENSE("GPL");
485MODULE_ALIAS("spi:at25");