1// SPDX-License-Identifier: GPL-2.0
   2/*
   3 * Driver for the PSC of the Freescale MPC52xx PSCs configured as UARTs.
   4 *
   5 * FIXME According to the usermanual the status bits in the status register
   6 * are only updated when the peripherals access the FIFO and not when the
   7 * CPU access them. So since we use this bits to know when we stop writing
   8 * and reading, they may not be updated in-time and a race condition may
   9 * exists. But I haven't be able to prove this and I don't care. But if
  10 * any problem arises, it might worth checking. The TX/RX FIFO Stats
  11 * registers should be used in addition.
  12 * Update: Actually, they seem updated ... At least the bits we use.
  13 *
  14 *
  15 * Maintainer : Sylvain Munaut <tnt@246tNt.com>
  16 *
  17 * Some of the code has been inspired/copied from the 2.4 code written
  18 * by Dale Farnsworth <dfarnsworth@mvista.com>.
  19 *
  20 * Copyright (C) 2008 Freescale Semiconductor Inc.
  21 *                    John Rigby <jrigby@gmail.com>
  22 * Added support for MPC5121
  23 * Copyright (C) 2006 Secret Lab Technologies Ltd.
  24 *                    Grant Likely <grant.likely@secretlab.ca>
  25 * Copyright (C) 2004-2006 Sylvain Munaut <tnt@246tNt.com>
  26 * Copyright (C) 2003 MontaVista, Software, Inc.
 
 
 
 
  27 */
  28
  29#undef DEBUG
  30
  31#include <linux/device.h>
  32#include <linux/module.h>
  33#include <linux/tty.h>
  34#include <linux/tty_flip.h>
  35#include <linux/serial.h>
  36#include <linux/sysrq.h>
  37#include <linux/console.h>
  38#include <linux/delay.h>
  39#include <linux/io.h>
  40#include <linux/of.h>
  41#include <linux/of_address.h>
  42#include <linux/of_irq.h>
  43#include <linux/platform_device.h>
  44#include <linux/clk.h>
  45
  46#include <asm/mpc52xx.h>
  47#include <asm/mpc52xx_psc.h>
  48
 
 
 
 
  49#include <linux/serial_core.h>
  50
  51
  52/* We've been assigned a range on the "Low-density serial ports" major */
  53#define SERIAL_PSC_MAJOR	204
  54#define SERIAL_PSC_MINOR	148
  55
  56
  57#define ISR_PASS_LIMIT 256	/* Max number of iteration in the interrupt */
  58
  59
  60static struct uart_port mpc52xx_uart_ports[MPC52xx_PSC_MAXNUM];
  61	/* Rem: - We use the read_status_mask as a shadow of
  62	 *        psc->mpc52xx_psc_imr
  63	 *      - It's important that is array is all zero on start as we
  64	 *        use it to know if it's initialized or not ! If it's not sure
  65	 *        it's cleared, then a memset(...,0,...) should be added to
  66	 *        the console_init
  67	 */
  68
  69/* lookup table for matching device nodes to index numbers */
  70static struct device_node *mpc52xx_uart_nodes[MPC52xx_PSC_MAXNUM];
  71
  72static void mpc52xx_uart_of_enumerate(void);
  73
  74
  75#define PSC(port) ((struct mpc52xx_psc __iomem *)((port)->membase))
  76
  77
  78/* Forward declaration of the interruption handling routine */
  79static irqreturn_t mpc52xx_uart_int(int irq, void *dev_id);
  80static irqreturn_t mpc5xxx_uart_process_int(struct uart_port *port);
  81
 
 
 
 
 
 
 
 
 
 
  82/* ======================================================================== */
  83/* PSC fifo operations for isolating differences between 52xx and 512x      */
  84/* ======================================================================== */
  85
  86struct psc_ops {
  87	void		(*fifo_init)(struct uart_port *port);
  88	unsigned int	(*raw_rx_rdy)(struct uart_port *port);
  89	unsigned int	(*raw_tx_rdy)(struct uart_port *port);
  90	unsigned int	(*rx_rdy)(struct uart_port *port);
  91	unsigned int	(*tx_rdy)(struct uart_port *port);
  92	unsigned int	(*tx_empty)(struct uart_port *port);
  93	void		(*stop_rx)(struct uart_port *port);
  94	void		(*start_tx)(struct uart_port *port);
  95	void		(*stop_tx)(struct uart_port *port);
  96	void		(*rx_clr_irq)(struct uart_port *port);
  97	void		(*tx_clr_irq)(struct uart_port *port);
  98	void		(*write_char)(struct uart_port *port, unsigned char c);
  99	unsigned char	(*read_char)(struct uart_port *port);
 100	void		(*cw_disable_ints)(struct uart_port *port);
 101	void		(*cw_restore_ints)(struct uart_port *port);
 102	unsigned int	(*set_baudrate)(struct uart_port *port,
 103					struct ktermios *new,
 104					const struct ktermios *old);
 105	int		(*clock_alloc)(struct uart_port *port);
 106	void		(*clock_relse)(struct uart_port *port);
 107	int		(*clock)(struct uart_port *port, int enable);
 108	int		(*fifoc_init)(void);
 109	void		(*fifoc_uninit)(void);
 110	void		(*get_irq)(struct uart_port *, struct device_node *);
 111	irqreturn_t	(*handle_irq)(struct uart_port *port);
 112	u16		(*get_status)(struct uart_port *port);
 113	u8		(*get_ipcr)(struct uart_port *port);
 114	void		(*command)(struct uart_port *port, u8 cmd);
 115	void		(*set_mode)(struct uart_port *port, u8 mr1, u8 mr2);
 116	void		(*set_rts)(struct uart_port *port, int state);
 117	void		(*enable_ms)(struct uart_port *port);
 118	void		(*set_sicr)(struct uart_port *port, u32 val);
 119	void		(*set_imr)(struct uart_port *port, u16 val);
 120	u8		(*get_mr1)(struct uart_port *port);
 121};
 122
 123/* setting the prescaler and divisor reg is common for all chips */
 124static inline void mpc52xx_set_divisor(struct mpc52xx_psc __iomem *psc,
 125				       u16 prescaler, unsigned int divisor)
 126{
 127	/* select prescaler */
 128	out_be16(&psc->mpc52xx_psc_clock_select, prescaler);
 129	out_8(&psc->ctur, divisor >> 8);
 130	out_8(&psc->ctlr, divisor & 0xff);
 131}
 132
 133static u16 mpc52xx_psc_get_status(struct uart_port *port)
 134{
 135	return in_be16(&PSC(port)->mpc52xx_psc_status);
 136}
 137
 138static u8 mpc52xx_psc_get_ipcr(struct uart_port *port)
 139{
 140	return in_8(&PSC(port)->mpc52xx_psc_ipcr);
 141}
 142
 143static void mpc52xx_psc_command(struct uart_port *port, u8 cmd)
 144{
 145	out_8(&PSC(port)->command, cmd);
 146}
 147
 148static void mpc52xx_psc_set_mode(struct uart_port *port, u8 mr1, u8 mr2)
 149{
 150	out_8(&PSC(port)->command, MPC52xx_PSC_SEL_MODE_REG_1);
 151	out_8(&PSC(port)->mode, mr1);
 152	out_8(&PSC(port)->mode, mr2);
 153}
 154
 155static void mpc52xx_psc_set_rts(struct uart_port *port, int state)
 156{
 157	if (state)
 158		out_8(&PSC(port)->op1, MPC52xx_PSC_OP_RTS);
 159	else
 160		out_8(&PSC(port)->op0, MPC52xx_PSC_OP_RTS);
 161}
 162
 163static void mpc52xx_psc_enable_ms(struct uart_port *port)
 164{
 165	struct mpc52xx_psc __iomem *psc = PSC(port);
 166
 167	/* clear D_*-bits by reading them */
 168	in_8(&psc->mpc52xx_psc_ipcr);
 169	/* enable CTS and DCD as IPC interrupts */
 170	out_8(&psc->mpc52xx_psc_acr, MPC52xx_PSC_IEC_CTS | MPC52xx_PSC_IEC_DCD);
 171
 172	port->read_status_mask |= MPC52xx_PSC_IMR_IPC;
 173	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
 174}
 175
 176static void mpc52xx_psc_set_sicr(struct uart_port *port, u32 val)
 177{
 178	out_be32(&PSC(port)->sicr, val);
 179}
 180
 181static void mpc52xx_psc_set_imr(struct uart_port *port, u16 val)
 182{
 183	out_be16(&PSC(port)->mpc52xx_psc_imr, val);
 184}
 185
 186static u8 mpc52xx_psc_get_mr1(struct uart_port *port)
 187{
 188	out_8(&PSC(port)->command, MPC52xx_PSC_SEL_MODE_REG_1);
 189	return in_8(&PSC(port)->mode);
 190}
 191
 192#ifdef CONFIG_PPC_MPC52xx
 193#define FIFO_52xx(port) ((struct mpc52xx_psc_fifo __iomem *)(PSC(port)+1))
 194static void mpc52xx_psc_fifo_init(struct uart_port *port)
 195{
 196	struct mpc52xx_psc __iomem *psc = PSC(port);
 197	struct mpc52xx_psc_fifo __iomem *fifo = FIFO_52xx(port);
 198
 199	out_8(&fifo->rfcntl, 0x00);
 200	out_be16(&fifo->rfalarm, 0x1ff);
 201	out_8(&fifo->tfcntl, 0x07);
 202	out_be16(&fifo->tfalarm, 0x80);
 203
 204	port->read_status_mask |= MPC52xx_PSC_IMR_RXRDY | MPC52xx_PSC_IMR_TXRDY;
 205	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
 206}
 207
 208static unsigned int mpc52xx_psc_raw_rx_rdy(struct uart_port *port)
 209{
 210	return in_be16(&PSC(port)->mpc52xx_psc_status)
 211	    & MPC52xx_PSC_SR_RXRDY;
 212}
 213
 214static unsigned int mpc52xx_psc_raw_tx_rdy(struct uart_port *port)
 215{
 216	return in_be16(&PSC(port)->mpc52xx_psc_status)
 217	    & MPC52xx_PSC_SR_TXRDY;
 218}
 219
 220
 221static unsigned int mpc52xx_psc_rx_rdy(struct uart_port *port)
 222{
 223	return in_be16(&PSC(port)->mpc52xx_psc_isr)
 224	    & port->read_status_mask
 225	    & MPC52xx_PSC_IMR_RXRDY;
 226}
 227
 228static unsigned int mpc52xx_psc_tx_rdy(struct uart_port *port)
 229{
 230	return in_be16(&PSC(port)->mpc52xx_psc_isr)
 231	    & port->read_status_mask
 232	    & MPC52xx_PSC_IMR_TXRDY;
 233}
 234
 235static unsigned int mpc52xx_psc_tx_empty(struct uart_port *port)
 236{
 237	u16 sts = in_be16(&PSC(port)->mpc52xx_psc_status);
 238
 239	return (sts & MPC52xx_PSC_SR_TXEMP) ? TIOCSER_TEMT : 0;
 240}
 241
 242static void mpc52xx_psc_start_tx(struct uart_port *port)
 243{
 244	port->read_status_mask |= MPC52xx_PSC_IMR_TXRDY;
 245	out_be16(&PSC(port)->mpc52xx_psc_imr, port->read_status_mask);
 246}
 247
 248static void mpc52xx_psc_stop_tx(struct uart_port *port)
 249{
 250	port->read_status_mask &= ~MPC52xx_PSC_IMR_TXRDY;
 251	out_be16(&PSC(port)->mpc52xx_psc_imr, port->read_status_mask);
 252}
 253
 254static void mpc52xx_psc_stop_rx(struct uart_port *port)
 255{
 256	port->read_status_mask &= ~MPC52xx_PSC_IMR_RXRDY;
 257	out_be16(&PSC(port)->mpc52xx_psc_imr, port->read_status_mask);
 258}
 259
 260static void mpc52xx_psc_rx_clr_irq(struct uart_port *port)
 261{
 262}
 263
 264static void mpc52xx_psc_tx_clr_irq(struct uart_port *port)
 265{
 266}
 267
 268static void mpc52xx_psc_write_char(struct uart_port *port, unsigned char c)
 269{
 270	out_8(&PSC(port)->mpc52xx_psc_buffer_8, c);
 271}
 272
 273static unsigned char mpc52xx_psc_read_char(struct uart_port *port)
 274{
 275	return in_8(&PSC(port)->mpc52xx_psc_buffer_8);
 276}
 277
 278static void mpc52xx_psc_cw_disable_ints(struct uart_port *port)
 279{
 280	out_be16(&PSC(port)->mpc52xx_psc_imr, 0);
 281}
 282
 283static void mpc52xx_psc_cw_restore_ints(struct uart_port *port)
 284{
 285	out_be16(&PSC(port)->mpc52xx_psc_imr, port->read_status_mask);
 286}
 287
 288static unsigned int mpc5200_psc_set_baudrate(struct uart_port *port,
 289					     struct ktermios *new,
 290					     const struct ktermios *old)
 291{
 292	unsigned int baud;
 293	unsigned int divisor;
 294
 295	/* The 5200 has a fixed /32 prescaler, uartclk contains the ipb freq */
 296	baud = uart_get_baud_rate(port, new, old,
 297				  port->uartclk / (32 * 0xffff) + 1,
 298				  port->uartclk / 32);
 299	divisor = (port->uartclk + 16 * baud) / (32 * baud);
 300
 301	/* enable the /32 prescaler and set the divisor */
 302	mpc52xx_set_divisor(PSC(port), 0xdd00, divisor);
 303	return baud;
 304}
 305
 306static unsigned int mpc5200b_psc_set_baudrate(struct uart_port *port,
 307					      struct ktermios *new,
 308					      const struct ktermios *old)
 309{
 310	unsigned int baud;
 311	unsigned int divisor;
 312	u16 prescaler;
 313
 314	/* The 5200B has a selectable /4 or /32 prescaler, uartclk contains the
 315	 * ipb freq */
 316	baud = uart_get_baud_rate(port, new, old,
 317				  port->uartclk / (32 * 0xffff) + 1,
 318				  port->uartclk / 4);
 319	divisor = (port->uartclk + 2 * baud) / (4 * baud);
 320
 321	/* select the proper prescaler and set the divisor
 322	 * prefer high prescaler for more tolerance on low baudrates */
 323	if (divisor > 0xffff || baud <= 115200) {
 324		divisor = (divisor + 4) / 8;
 325		prescaler = 0xdd00; /* /32 */
 326	} else
 327		prescaler = 0xff00; /* /4 */
 328	mpc52xx_set_divisor(PSC(port), prescaler, divisor);
 329	return baud;
 330}
 331
 332static void mpc52xx_psc_get_irq(struct uart_port *port, struct device_node *np)
 333{
 334	port->irqflags = 0;
 335	port->irq = irq_of_parse_and_map(np, 0);
 336}
 337
 338/* 52xx specific interrupt handler. The caller holds the port lock */
 339static irqreturn_t mpc52xx_psc_handle_irq(struct uart_port *port)
 340{
 341	return mpc5xxx_uart_process_int(port);
 342}
 343
 344static const struct psc_ops mpc52xx_psc_ops = {
 345	.fifo_init = mpc52xx_psc_fifo_init,
 346	.raw_rx_rdy = mpc52xx_psc_raw_rx_rdy,
 347	.raw_tx_rdy = mpc52xx_psc_raw_tx_rdy,
 348	.rx_rdy = mpc52xx_psc_rx_rdy,
 349	.tx_rdy = mpc52xx_psc_tx_rdy,
 350	.tx_empty = mpc52xx_psc_tx_empty,
 351	.stop_rx = mpc52xx_psc_stop_rx,
 352	.start_tx = mpc52xx_psc_start_tx,
 353	.stop_tx = mpc52xx_psc_stop_tx,
 354	.rx_clr_irq = mpc52xx_psc_rx_clr_irq,
 355	.tx_clr_irq = mpc52xx_psc_tx_clr_irq,
 356	.write_char = mpc52xx_psc_write_char,
 357	.read_char = mpc52xx_psc_read_char,
 358	.cw_disable_ints = mpc52xx_psc_cw_disable_ints,
 359	.cw_restore_ints = mpc52xx_psc_cw_restore_ints,
 360	.set_baudrate = mpc5200_psc_set_baudrate,
 361	.get_irq = mpc52xx_psc_get_irq,
 362	.handle_irq = mpc52xx_psc_handle_irq,
 363	.get_status = mpc52xx_psc_get_status,
 364	.get_ipcr = mpc52xx_psc_get_ipcr,
 365	.command = mpc52xx_psc_command,
 366	.set_mode = mpc52xx_psc_set_mode,
 367	.set_rts = mpc52xx_psc_set_rts,
 368	.enable_ms = mpc52xx_psc_enable_ms,
 369	.set_sicr = mpc52xx_psc_set_sicr,
 370	.set_imr = mpc52xx_psc_set_imr,
 371	.get_mr1 = mpc52xx_psc_get_mr1,
 372};
 373
 374static const struct psc_ops mpc5200b_psc_ops = {
 375	.fifo_init = mpc52xx_psc_fifo_init,
 376	.raw_rx_rdy = mpc52xx_psc_raw_rx_rdy,
 377	.raw_tx_rdy = mpc52xx_psc_raw_tx_rdy,
 378	.rx_rdy = mpc52xx_psc_rx_rdy,
 379	.tx_rdy = mpc52xx_psc_tx_rdy,
 380	.tx_empty = mpc52xx_psc_tx_empty,
 381	.stop_rx = mpc52xx_psc_stop_rx,
 382	.start_tx = mpc52xx_psc_start_tx,
 383	.stop_tx = mpc52xx_psc_stop_tx,
 384	.rx_clr_irq = mpc52xx_psc_rx_clr_irq,
 385	.tx_clr_irq = mpc52xx_psc_tx_clr_irq,
 386	.write_char = mpc52xx_psc_write_char,
 387	.read_char = mpc52xx_psc_read_char,
 388	.cw_disable_ints = mpc52xx_psc_cw_disable_ints,
 389	.cw_restore_ints = mpc52xx_psc_cw_restore_ints,
 390	.set_baudrate = mpc5200b_psc_set_baudrate,
 391	.get_irq = mpc52xx_psc_get_irq,
 392	.handle_irq = mpc52xx_psc_handle_irq,
 393	.get_status = mpc52xx_psc_get_status,
 394	.get_ipcr = mpc52xx_psc_get_ipcr,
 395	.command = mpc52xx_psc_command,
 396	.set_mode = mpc52xx_psc_set_mode,
 397	.set_rts = mpc52xx_psc_set_rts,
 398	.enable_ms = mpc52xx_psc_enable_ms,
 399	.set_sicr = mpc52xx_psc_set_sicr,
 400	.set_imr = mpc52xx_psc_set_imr,
 401	.get_mr1 = mpc52xx_psc_get_mr1,
 402};
 403
 404#endif /* CONFIG_PPC_MPC52xx */
 405
 406#ifdef CONFIG_PPC_MPC512x
 407#define FIFO_512x(port) ((struct mpc512x_psc_fifo __iomem *)(PSC(port)+1))
 408
 409/* PSC FIFO Controller for mpc512x */
 410struct psc_fifoc {
 411	u32 fifoc_cmd;
 412	u32 fifoc_int;
 413	u32 fifoc_dma;
 414	u32 fifoc_axe;
 415	u32 fifoc_debug;
 416};
 417
 418static struct psc_fifoc __iomem *psc_fifoc;
 419static unsigned int psc_fifoc_irq;
 420static struct clk *psc_fifoc_clk;
 421
 422static void mpc512x_psc_fifo_init(struct uart_port *port)
 423{
 424	/* /32 prescaler */
 425	out_be16(&PSC(port)->mpc52xx_psc_clock_select, 0xdd00);
 426
 427	out_be32(&FIFO_512x(port)->txcmd, MPC512x_PSC_FIFO_RESET_SLICE);
 428	out_be32(&FIFO_512x(port)->txcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
 429	out_be32(&FIFO_512x(port)->txalarm, 1);
 430	out_be32(&FIFO_512x(port)->tximr, 0);
 431
 432	out_be32(&FIFO_512x(port)->rxcmd, MPC512x_PSC_FIFO_RESET_SLICE);
 433	out_be32(&FIFO_512x(port)->rxcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
 434	out_be32(&FIFO_512x(port)->rxalarm, 1);
 435	out_be32(&FIFO_512x(port)->rximr, 0);
 436
 437	out_be32(&FIFO_512x(port)->tximr, MPC512x_PSC_FIFO_ALARM);
 438	out_be32(&FIFO_512x(port)->rximr, MPC512x_PSC_FIFO_ALARM);
 439}
 440
 441static unsigned int mpc512x_psc_raw_rx_rdy(struct uart_port *port)
 442{
 443	return !(in_be32(&FIFO_512x(port)->rxsr) & MPC512x_PSC_FIFO_EMPTY);
 444}
 445
 446static unsigned int mpc512x_psc_raw_tx_rdy(struct uart_port *port)
 447{
 448	return !(in_be32(&FIFO_512x(port)->txsr) & MPC512x_PSC_FIFO_FULL);
 449}
 450
 451static unsigned int mpc512x_psc_rx_rdy(struct uart_port *port)
 452{
 453	return in_be32(&FIFO_512x(port)->rxsr)
 454	    & in_be32(&FIFO_512x(port)->rximr)
 455	    & MPC512x_PSC_FIFO_ALARM;
 456}
 457
 458static unsigned int mpc512x_psc_tx_rdy(struct uart_port *port)
 459{
 460	return in_be32(&FIFO_512x(port)->txsr)
 461	    & in_be32(&FIFO_512x(port)->tximr)
 462	    & MPC512x_PSC_FIFO_ALARM;
 463}
 464
 465static unsigned int mpc512x_psc_tx_empty(struct uart_port *port)
 466{
 467	return in_be32(&FIFO_512x(port)->txsr)
 468	    & MPC512x_PSC_FIFO_EMPTY;
 469}
 470
 471static void mpc512x_psc_stop_rx(struct uart_port *port)
 472{
 473	unsigned long rx_fifo_imr;
 474
 475	rx_fifo_imr = in_be32(&FIFO_512x(port)->rximr);
 476	rx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
 477	out_be32(&FIFO_512x(port)->rximr, rx_fifo_imr);
 478}
 479
 480static void mpc512x_psc_start_tx(struct uart_port *port)
 481{
 482	unsigned long tx_fifo_imr;
 483
 484	tx_fifo_imr = in_be32(&FIFO_512x(port)->tximr);
 485	tx_fifo_imr |= MPC512x_PSC_FIFO_ALARM;
 486	out_be32(&FIFO_512x(port)->tximr, tx_fifo_imr);
 487}
 488
 489static void mpc512x_psc_stop_tx(struct uart_port *port)
 490{
 491	unsigned long tx_fifo_imr;
 492
 493	tx_fifo_imr = in_be32(&FIFO_512x(port)->tximr);
 494	tx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
 495	out_be32(&FIFO_512x(port)->tximr, tx_fifo_imr);
 496}
 497
 498static void mpc512x_psc_rx_clr_irq(struct uart_port *port)
 499{
 500	out_be32(&FIFO_512x(port)->rxisr, in_be32(&FIFO_512x(port)->rxisr));
 501}
 502
 503static void mpc512x_psc_tx_clr_irq(struct uart_port *port)
 504{
 505	out_be32(&FIFO_512x(port)->txisr, in_be32(&FIFO_512x(port)->txisr));
 506}
 507
 508static void mpc512x_psc_write_char(struct uart_port *port, unsigned char c)
 509{
 510	out_8(&FIFO_512x(port)->txdata_8, c);
 511}
 512
 513static unsigned char mpc512x_psc_read_char(struct uart_port *port)
 514{
 515	return in_8(&FIFO_512x(port)->rxdata_8);
 516}
 517
 518static void mpc512x_psc_cw_disable_ints(struct uart_port *port)
 519{
 520	port->read_status_mask =
 521		in_be32(&FIFO_512x(port)->tximr) << 16 |
 522		in_be32(&FIFO_512x(port)->rximr);
 523	out_be32(&FIFO_512x(port)->tximr, 0);
 524	out_be32(&FIFO_512x(port)->rximr, 0);
 525}
 526
 527static void mpc512x_psc_cw_restore_ints(struct uart_port *port)
 528{
 529	out_be32(&FIFO_512x(port)->tximr,
 530		(port->read_status_mask >> 16) & 0x7f);
 531	out_be32(&FIFO_512x(port)->rximr, port->read_status_mask & 0x7f);
 532}
 533
 534static unsigned int mpc512x_psc_set_baudrate(struct uart_port *port,
 535					     struct ktermios *new,
 536					     const struct ktermios *old)
 537{
 538	unsigned int baud;
 539	unsigned int divisor;
 540
 541	/*
 542	 * The "MPC5121e Microcontroller Reference Manual, Rev. 3" says on
 543	 * pg. 30-10 that the chip supports a /32 and a /10 prescaler.
 544	 * Furthermore, it states that "After reset, the prescaler by 10
 545	 * for the UART mode is selected", but the reset register value is
 546	 * 0x0000 which means a /32 prescaler. This is wrong.
 547	 *
 548	 * In reality using /32 prescaler doesn't work, as it is not supported!
 549	 * Use /16 or /10 prescaler, see "MPC5121e Hardware Design Guide",
 550	 * Chapter 4.1 PSC in UART Mode.
 551	 * Calculate with a /16 prescaler here.
 552	 */
 553
 554	/* uartclk contains the ips freq */
 555	baud = uart_get_baud_rate(port, new, old,
 556				  port->uartclk / (16 * 0xffff) + 1,
 557				  port->uartclk / 16);
 558	divisor = (port->uartclk + 8 * baud) / (16 * baud);
 559
 560	/* enable the /16 prescaler and set the divisor */
 561	mpc52xx_set_divisor(PSC(port), 0xdd00, divisor);
 562	return baud;
 563}
 564
 565/* Init PSC FIFO Controller */
 566static int __init mpc512x_psc_fifoc_init(void)
 567{
 568	int err;
 569	struct device_node *np;
 570	struct clk *clk;
 571
 572	/* default error code, potentially overwritten by clock calls */
 573	err = -ENODEV;
 574
 575	np = of_find_compatible_node(NULL, NULL,
 576				     "fsl,mpc5121-psc-fifo");
 577	if (!np) {
 578		pr_err("%s: Can't find FIFOC node\n", __func__);
 579		goto out_err;
 580	}
 581
 582	clk = of_clk_get(np, 0);
 583	if (IS_ERR(clk)) {
 584		/* backwards compat with device trees that lack clock specs */
 585		clk = clk_get_sys(np->name, "ipg");
 586	}
 587	if (IS_ERR(clk)) {
 588		pr_err("%s: Can't lookup FIFO clock\n", __func__);
 589		err = PTR_ERR(clk);
 590		goto out_ofnode_put;
 591	}
 592	if (clk_prepare_enable(clk)) {
 593		pr_err("%s: Can't enable FIFO clock\n", __func__);
 594		clk_put(clk);
 595		goto out_ofnode_put;
 596	}
 597	psc_fifoc_clk = clk;
 598
 599	psc_fifoc = of_iomap(np, 0);
 600	if (!psc_fifoc) {
 601		pr_err("%s: Can't map FIFOC\n", __func__);
 602		goto out_clk_disable;
 
 603	}
 604
 605	psc_fifoc_irq = irq_of_parse_and_map(np, 0);
 606	if (psc_fifoc_irq == 0) {
 
 607		pr_err("%s: Can't get FIFOC irq\n", __func__);
 608		goto out_unmap;
 
 609	}
 610
 611	of_node_put(np);
 612	return 0;
 613
 614out_unmap:
 615	iounmap(psc_fifoc);
 616out_clk_disable:
 617	clk_disable_unprepare(psc_fifoc_clk);
 618	clk_put(psc_fifoc_clk);
 619out_ofnode_put:
 620	of_node_put(np);
 621out_err:
 622	return err;
 623}
 624
 625static void __exit mpc512x_psc_fifoc_uninit(void)
 626{
 627	iounmap(psc_fifoc);
 628
 629	/* disable the clock, errors are not fatal */
 630	if (psc_fifoc_clk) {
 631		clk_disable_unprepare(psc_fifoc_clk);
 632		clk_put(psc_fifoc_clk);
 633		psc_fifoc_clk = NULL;
 634	}
 635}
 636
 637/* 512x specific interrupt handler. The caller holds the port lock */
 638static irqreturn_t mpc512x_psc_handle_irq(struct uart_port *port)
 639{
 640	unsigned long fifoc_int;
 641	int psc_num;
 642
 643	/* Read pending PSC FIFOC interrupts */
 644	fifoc_int = in_be32(&psc_fifoc->fifoc_int);
 645
 646	/* Check if it is an interrupt for this port */
 647	psc_num = (port->mapbase & 0xf00) >> 8;
 648	if (test_bit(psc_num, &fifoc_int) ||
 649	    test_bit(psc_num + 16, &fifoc_int))
 650		return mpc5xxx_uart_process_int(port);
 651
 652	return IRQ_NONE;
 653}
 654
 655static struct clk *psc_mclk_clk[MPC52xx_PSC_MAXNUM];
 656static struct clk *psc_ipg_clk[MPC52xx_PSC_MAXNUM];
 657
 658/* called from within the .request_port() callback (allocation) */
 659static int mpc512x_psc_alloc_clock(struct uart_port *port)
 660{
 661	int psc_num;
 662	struct clk *clk;
 663	int err;
 664
 665	psc_num = (port->mapbase & 0xf00) >> 8;
 666
 667	clk = devm_clk_get(port->dev, "mclk");
 668	if (IS_ERR(clk)) {
 669		dev_err(port->dev, "Failed to get MCLK!\n");
 670		err = PTR_ERR(clk);
 671		goto out_err;
 672	}
 673	err = clk_prepare_enable(clk);
 674	if (err) {
 675		dev_err(port->dev, "Failed to enable MCLK!\n");
 676		goto out_err;
 677	}
 678	psc_mclk_clk[psc_num] = clk;
 679
 680	clk = devm_clk_get(port->dev, "ipg");
 681	if (IS_ERR(clk)) {
 682		dev_err(port->dev, "Failed to get IPG clock!\n");
 683		err = PTR_ERR(clk);
 684		goto out_err;
 685	}
 686	err = clk_prepare_enable(clk);
 687	if (err) {
 688		dev_err(port->dev, "Failed to enable IPG clock!\n");
 689		goto out_err;
 690	}
 691	psc_ipg_clk[psc_num] = clk;
 692
 693	return 0;
 694
 695out_err:
 696	if (psc_mclk_clk[psc_num]) {
 697		clk_disable_unprepare(psc_mclk_clk[psc_num]);
 698		psc_mclk_clk[psc_num] = NULL;
 699	}
 700	if (psc_ipg_clk[psc_num]) {
 701		clk_disable_unprepare(psc_ipg_clk[psc_num]);
 702		psc_ipg_clk[psc_num] = NULL;
 703	}
 704	return err;
 705}
 706
 707/* called from within the .release_port() callback (release) */
 708static void mpc512x_psc_relse_clock(struct uart_port *port)
 709{
 710	int psc_num;
 711	struct clk *clk;
 712
 713	psc_num = (port->mapbase & 0xf00) >> 8;
 714	clk = psc_mclk_clk[psc_num];
 715	if (clk) {
 716		clk_disable_unprepare(clk);
 717		psc_mclk_clk[psc_num] = NULL;
 718	}
 719	if (psc_ipg_clk[psc_num]) {
 720		clk_disable_unprepare(psc_ipg_clk[psc_num]);
 721		psc_ipg_clk[psc_num] = NULL;
 722	}
 723}
 724
 725/* implementation of the .clock() callback (enable/disable) */
 726static int mpc512x_psc_endis_clock(struct uart_port *port, int enable)
 727{
 728	int psc_num;
 729	struct clk *psc_clk;
 730	int ret;
 
 731
 732	if (uart_console(port))
 733		return 0;
 734
 735	psc_num = (port->mapbase & 0xf00) >> 8;
 736	psc_clk = psc_mclk_clk[psc_num];
 737	if (!psc_clk) {
 
 738		dev_err(port->dev, "Failed to get PSC clock entry!\n");
 739		return -ENODEV;
 740	}
 741
 742	dev_dbg(port->dev, "mclk %sable\n", enable ? "en" : "dis");
 743	if (enable) {
 744		ret = clk_enable(psc_clk);
 745		if (ret)
 746			dev_err(port->dev, "Failed to enable MCLK!\n");
 747		return ret;
 748	} else {
 749		clk_disable(psc_clk);
 750		return 0;
 751	}
 752}
 753
 754static void mpc512x_psc_get_irq(struct uart_port *port, struct device_node *np)
 755{
 756	port->irqflags = IRQF_SHARED;
 757	port->irq = psc_fifoc_irq;
 758}
 759
 760#define PSC_5125(port) ((struct mpc5125_psc __iomem *)((port)->membase))
 761#define FIFO_5125(port) ((struct mpc512x_psc_fifo __iomem *)(PSC_5125(port)+1))
 762
 763static void mpc5125_psc_fifo_init(struct uart_port *port)
 764{
 765	/* /32 prescaler */
 766	out_8(&PSC_5125(port)->mpc52xx_psc_clock_select, 0xdd);
 767
 768	out_be32(&FIFO_5125(port)->txcmd, MPC512x_PSC_FIFO_RESET_SLICE);
 769	out_be32(&FIFO_5125(port)->txcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
 770	out_be32(&FIFO_5125(port)->txalarm, 1);
 771	out_be32(&FIFO_5125(port)->tximr, 0);
 772
 773	out_be32(&FIFO_5125(port)->rxcmd, MPC512x_PSC_FIFO_RESET_SLICE);
 774	out_be32(&FIFO_5125(port)->rxcmd, MPC512x_PSC_FIFO_ENABLE_SLICE);
 775	out_be32(&FIFO_5125(port)->rxalarm, 1);
 776	out_be32(&FIFO_5125(port)->rximr, 0);
 777
 778	out_be32(&FIFO_5125(port)->tximr, MPC512x_PSC_FIFO_ALARM);
 779	out_be32(&FIFO_5125(port)->rximr, MPC512x_PSC_FIFO_ALARM);
 780}
 781
 782static unsigned int mpc5125_psc_raw_rx_rdy(struct uart_port *port)
 783{
 784	return !(in_be32(&FIFO_5125(port)->rxsr) & MPC512x_PSC_FIFO_EMPTY);
 785}
 786
 787static unsigned int mpc5125_psc_raw_tx_rdy(struct uart_port *port)
 788{
 789	return !(in_be32(&FIFO_5125(port)->txsr) & MPC512x_PSC_FIFO_FULL);
 790}
 791
 792static unsigned int mpc5125_psc_rx_rdy(struct uart_port *port)
 793{
 794	return in_be32(&FIFO_5125(port)->rxsr) &
 795	       in_be32(&FIFO_5125(port)->rximr) & MPC512x_PSC_FIFO_ALARM;
 796}
 797
 798static unsigned int mpc5125_psc_tx_rdy(struct uart_port *port)
 799{
 800	return in_be32(&FIFO_5125(port)->txsr) &
 801	       in_be32(&FIFO_5125(port)->tximr) & MPC512x_PSC_FIFO_ALARM;
 802}
 803
 804static unsigned int mpc5125_psc_tx_empty(struct uart_port *port)
 805{
 806	return in_be32(&FIFO_5125(port)->txsr) & MPC512x_PSC_FIFO_EMPTY;
 807}
 808
 809static void mpc5125_psc_stop_rx(struct uart_port *port)
 810{
 811	unsigned long rx_fifo_imr;
 812
 813	rx_fifo_imr = in_be32(&FIFO_5125(port)->rximr);
 814	rx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
 815	out_be32(&FIFO_5125(port)->rximr, rx_fifo_imr);
 816}
 817
 818static void mpc5125_psc_start_tx(struct uart_port *port)
 819{
 820	unsigned long tx_fifo_imr;
 821
 822	tx_fifo_imr = in_be32(&FIFO_5125(port)->tximr);
 823	tx_fifo_imr |= MPC512x_PSC_FIFO_ALARM;
 824	out_be32(&FIFO_5125(port)->tximr, tx_fifo_imr);
 825}
 826
 827static void mpc5125_psc_stop_tx(struct uart_port *port)
 828{
 829	unsigned long tx_fifo_imr;
 830
 831	tx_fifo_imr = in_be32(&FIFO_5125(port)->tximr);
 832	tx_fifo_imr &= ~MPC512x_PSC_FIFO_ALARM;
 833	out_be32(&FIFO_5125(port)->tximr, tx_fifo_imr);
 834}
 835
 836static void mpc5125_psc_rx_clr_irq(struct uart_port *port)
 837{
 838	out_be32(&FIFO_5125(port)->rxisr, in_be32(&FIFO_5125(port)->rxisr));
 839}
 840
 841static void mpc5125_psc_tx_clr_irq(struct uart_port *port)
 842{
 843	out_be32(&FIFO_5125(port)->txisr, in_be32(&FIFO_5125(port)->txisr));
 844}
 845
 846static void mpc5125_psc_write_char(struct uart_port *port, unsigned char c)
 847{
 848	out_8(&FIFO_5125(port)->txdata_8, c);
 849}
 850
 851static unsigned char mpc5125_psc_read_char(struct uart_port *port)
 852{
 853	return in_8(&FIFO_5125(port)->rxdata_8);
 854}
 855
 856static void mpc5125_psc_cw_disable_ints(struct uart_port *port)
 857{
 858	port->read_status_mask =
 859		in_be32(&FIFO_5125(port)->tximr) << 16 |
 860		in_be32(&FIFO_5125(port)->rximr);
 861	out_be32(&FIFO_5125(port)->tximr, 0);
 862	out_be32(&FIFO_5125(port)->rximr, 0);
 863}
 864
 865static void mpc5125_psc_cw_restore_ints(struct uart_port *port)
 866{
 867	out_be32(&FIFO_5125(port)->tximr,
 868		(port->read_status_mask >> 16) & 0x7f);
 869	out_be32(&FIFO_5125(port)->rximr, port->read_status_mask & 0x7f);
 870}
 871
 872static inline void mpc5125_set_divisor(struct mpc5125_psc __iomem *psc,
 873		u8 prescaler, unsigned int divisor)
 874{
 875	/* select prescaler */
 876	out_8(&psc->mpc52xx_psc_clock_select, prescaler);
 877	out_8(&psc->ctur, divisor >> 8);
 878	out_8(&psc->ctlr, divisor & 0xff);
 879}
 880
 881static unsigned int mpc5125_psc_set_baudrate(struct uart_port *port,
 882					     struct ktermios *new,
 883					     const struct ktermios *old)
 884{
 885	unsigned int baud;
 886	unsigned int divisor;
 887
 888	/*
 889	 * Calculate with a /16 prescaler here.
 890	 */
 891
 892	/* uartclk contains the ips freq */
 893	baud = uart_get_baud_rate(port, new, old,
 894				  port->uartclk / (16 * 0xffff) + 1,
 895				  port->uartclk / 16);
 896	divisor = (port->uartclk + 8 * baud) / (16 * baud);
 897
 898	/* enable the /16 prescaler and set the divisor */
 899	mpc5125_set_divisor(PSC_5125(port), 0xdd, divisor);
 900	return baud;
 901}
 902
 903/*
 904 * MPC5125 have compatible PSC FIFO Controller.
 905 * Special init not needed.
 906 */
 907static u16 mpc5125_psc_get_status(struct uart_port *port)
 908{
 909	return in_be16(&PSC_5125(port)->mpc52xx_psc_status);
 910}
 911
 912static u8 mpc5125_psc_get_ipcr(struct uart_port *port)
 913{
 914	return in_8(&PSC_5125(port)->mpc52xx_psc_ipcr);
 915}
 916
 917static void mpc5125_psc_command(struct uart_port *port, u8 cmd)
 918{
 919	out_8(&PSC_5125(port)->command, cmd);
 920}
 921
 922static void mpc5125_psc_set_mode(struct uart_port *port, u8 mr1, u8 mr2)
 923{
 924	out_8(&PSC_5125(port)->mr1, mr1);
 925	out_8(&PSC_5125(port)->mr2, mr2);
 926}
 927
 928static void mpc5125_psc_set_rts(struct uart_port *port, int state)
 929{
 930	if (state & TIOCM_RTS)
 931		out_8(&PSC_5125(port)->op1, MPC52xx_PSC_OP_RTS);
 932	else
 933		out_8(&PSC_5125(port)->op0, MPC52xx_PSC_OP_RTS);
 934}
 935
 936static void mpc5125_psc_enable_ms(struct uart_port *port)
 937{
 938	struct mpc5125_psc __iomem *psc = PSC_5125(port);
 939
 940	/* clear D_*-bits by reading them */
 941	in_8(&psc->mpc52xx_psc_ipcr);
 942	/* enable CTS and DCD as IPC interrupts */
 943	out_8(&psc->mpc52xx_psc_acr, MPC52xx_PSC_IEC_CTS | MPC52xx_PSC_IEC_DCD);
 944
 945	port->read_status_mask |= MPC52xx_PSC_IMR_IPC;
 946	out_be16(&psc->mpc52xx_psc_imr, port->read_status_mask);
 947}
 948
 949static void mpc5125_psc_set_sicr(struct uart_port *port, u32 val)
 950{
 951	out_be32(&PSC_5125(port)->sicr, val);
 952}
 953
 954static void mpc5125_psc_set_imr(struct uart_port *port, u16 val)
 955{
 956	out_be16(&PSC_5125(port)->mpc52xx_psc_imr, val);
 957}
 958
 959static u8 mpc5125_psc_get_mr1(struct uart_port *port)
 960{
 961	return in_8(&PSC_5125(port)->mr1);
 962}
 963
 964static const struct psc_ops mpc5125_psc_ops = {
 965	.fifo_init = mpc5125_psc_fifo_init,
 966	.raw_rx_rdy = mpc5125_psc_raw_rx_rdy,
 967	.raw_tx_rdy = mpc5125_psc_raw_tx_rdy,
 968	.rx_rdy = mpc5125_psc_rx_rdy,
 969	.tx_rdy = mpc5125_psc_tx_rdy,
 970	.tx_empty = mpc5125_psc_tx_empty,
 971	.stop_rx = mpc5125_psc_stop_rx,
 972	.start_tx = mpc5125_psc_start_tx,
 973	.stop_tx = mpc5125_psc_stop_tx,
 974	.rx_clr_irq = mpc5125_psc_rx_clr_irq,
 975	.tx_clr_irq = mpc5125_psc_tx_clr_irq,
 976	.write_char = mpc5125_psc_write_char,
 977	.read_char = mpc5125_psc_read_char,
 978	.cw_disable_ints = mpc5125_psc_cw_disable_ints,
 979	.cw_restore_ints = mpc5125_psc_cw_restore_ints,
 980	.set_baudrate = mpc5125_psc_set_baudrate,
 981	.clock_alloc = mpc512x_psc_alloc_clock,
 982	.clock_relse = mpc512x_psc_relse_clock,
 983	.clock = mpc512x_psc_endis_clock,
 984	.fifoc_init = mpc512x_psc_fifoc_init,
 985	.fifoc_uninit = mpc512x_psc_fifoc_uninit,
 986	.get_irq = mpc512x_psc_get_irq,
 987	.handle_irq = mpc512x_psc_handle_irq,
 988	.get_status = mpc5125_psc_get_status,
 989	.get_ipcr = mpc5125_psc_get_ipcr,
 990	.command = mpc5125_psc_command,
 991	.set_mode = mpc5125_psc_set_mode,
 992	.set_rts = mpc5125_psc_set_rts,
 993	.enable_ms = mpc5125_psc_enable_ms,
 994	.set_sicr = mpc5125_psc_set_sicr,
 995	.set_imr = mpc5125_psc_set_imr,
 996	.get_mr1 = mpc5125_psc_get_mr1,
 997};
 998
 999static const struct psc_ops mpc512x_psc_ops = {
1000	.fifo_init = mpc512x_psc_fifo_init,
1001	.raw_rx_rdy = mpc512x_psc_raw_rx_rdy,
1002	.raw_tx_rdy = mpc512x_psc_raw_tx_rdy,
1003	.rx_rdy = mpc512x_psc_rx_rdy,
1004	.tx_rdy = mpc512x_psc_tx_rdy,
1005	.tx_empty = mpc512x_psc_tx_empty,
1006	.stop_rx = mpc512x_psc_stop_rx,
1007	.start_tx = mpc512x_psc_start_tx,
1008	.stop_tx = mpc512x_psc_stop_tx,
1009	.rx_clr_irq = mpc512x_psc_rx_clr_irq,
1010	.tx_clr_irq = mpc512x_psc_tx_clr_irq,
1011	.write_char = mpc512x_psc_write_char,
1012	.read_char = mpc512x_psc_read_char,
1013	.cw_disable_ints = mpc512x_psc_cw_disable_ints,
1014	.cw_restore_ints = mpc512x_psc_cw_restore_ints,
1015	.set_baudrate = mpc512x_psc_set_baudrate,
1016	.clock_alloc = mpc512x_psc_alloc_clock,
1017	.clock_relse = mpc512x_psc_relse_clock,
1018	.clock = mpc512x_psc_endis_clock,
1019	.fifoc_init = mpc512x_psc_fifoc_init,
1020	.fifoc_uninit = mpc512x_psc_fifoc_uninit,
1021	.get_irq = mpc512x_psc_get_irq,
1022	.handle_irq = mpc512x_psc_handle_irq,
1023	.get_status = mpc52xx_psc_get_status,
1024	.get_ipcr = mpc52xx_psc_get_ipcr,
1025	.command = mpc52xx_psc_command,
1026	.set_mode = mpc52xx_psc_set_mode,
1027	.set_rts = mpc52xx_psc_set_rts,
1028	.enable_ms = mpc52xx_psc_enable_ms,
1029	.set_sicr = mpc52xx_psc_set_sicr,
1030	.set_imr = mpc52xx_psc_set_imr,
1031	.get_mr1 = mpc52xx_psc_get_mr1,
1032};
1033#endif /* CONFIG_PPC_MPC512x */
1034
1035
1036static const struct psc_ops *psc_ops;
1037
1038/* ======================================================================== */
1039/* UART operations                                                          */
1040/* ======================================================================== */
1041
1042static unsigned int
1043mpc52xx_uart_tx_empty(struct uart_port *port)
1044{
1045	return psc_ops->tx_empty(port) ? TIOCSER_TEMT : 0;
1046}
1047
1048static void
1049mpc52xx_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
1050{
1051	psc_ops->set_rts(port, mctrl & TIOCM_RTS);
 
 
 
1052}
1053
1054static unsigned int
1055mpc52xx_uart_get_mctrl(struct uart_port *port)
1056{
1057	unsigned int ret = TIOCM_DSR;
1058	u8 status = psc_ops->get_ipcr(port);
1059
1060	if (!(status & MPC52xx_PSC_CTS))
1061		ret |= TIOCM_CTS;
1062	if (!(status & MPC52xx_PSC_DCD))
1063		ret |= TIOCM_CAR;
1064
1065	return ret;
1066}
1067
1068static void
1069mpc52xx_uart_stop_tx(struct uart_port *port)
1070{
1071	/* port->lock taken by caller */
1072	psc_ops->stop_tx(port);
1073}
1074
1075static void
1076mpc52xx_uart_start_tx(struct uart_port *port)
1077{
1078	/* port->lock taken by caller */
1079	psc_ops->start_tx(port);
1080}
1081
1082static void
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1083mpc52xx_uart_stop_rx(struct uart_port *port)
1084{
1085	/* port->lock taken by caller */
1086	psc_ops->stop_rx(port);
1087}
1088
1089static void
1090mpc52xx_uart_enable_ms(struct uart_port *port)
1091{
1092	psc_ops->enable_ms(port);
 
 
 
 
 
 
 
 
1093}
1094
1095static void
1096mpc52xx_uart_break_ctl(struct uart_port *port, int ctl)
1097{
1098	unsigned long flags;
1099	uart_port_lock_irqsave(port, &flags);
1100
1101	if (ctl == -1)
1102		psc_ops->command(port, MPC52xx_PSC_START_BRK);
1103	else
1104		psc_ops->command(port, MPC52xx_PSC_STOP_BRK);
1105
1106	uart_port_unlock_irqrestore(port, flags);
1107}
1108
1109static int
1110mpc52xx_uart_startup(struct uart_port *port)
1111{
 
1112	int ret;
1113
1114	if (psc_ops->clock) {
1115		ret = psc_ops->clock(port, 1);
1116		if (ret)
1117			return ret;
1118	}
1119
1120	/* Request IRQ */
1121	ret = request_irq(port->irq, mpc52xx_uart_int,
1122			  port->irqflags, "mpc52xx_psc_uart", port);
1123	if (ret)
1124		return ret;
1125
1126	/* Reset/activate the port, clear and enable interrupts */
1127	psc_ops->command(port, MPC52xx_PSC_RST_RX);
1128	psc_ops->command(port, MPC52xx_PSC_RST_TX);
1129
1130	/*
1131	 * According to Freescale's support the RST_TX command can produce a
1132	 * spike on the TX pin. So they recommend to delay "for one character".
1133	 * One millisecond should be enough for everyone.
1134	 */
1135	msleep(1);
1136
1137	psc_ops->set_sicr(port, 0);	/* UART mode DCD ignored */
1138
1139	psc_ops->fifo_init(port);
1140
1141	psc_ops->command(port, MPC52xx_PSC_TX_ENABLE);
1142	psc_ops->command(port, MPC52xx_PSC_RX_ENABLE);
1143
1144	return 0;
1145}
1146
1147static void
1148mpc52xx_uart_shutdown(struct uart_port *port)
1149{
 
 
1150	/* Shut down the port.  Leave TX active if on a console port */
1151	psc_ops->command(port, MPC52xx_PSC_RST_RX);
1152	if (!uart_console(port))
1153		psc_ops->command(port, MPC52xx_PSC_RST_TX);
1154
1155	port->read_status_mask = 0;
1156	psc_ops->set_imr(port, port->read_status_mask);
1157
1158	if (psc_ops->clock)
1159		psc_ops->clock(port, 0);
1160
1161	/* Disable interrupt */
1162	psc_ops->cw_disable_ints(port);
1163
1164	/* Release interrupt */
1165	free_irq(port->irq, port);
1166}
1167
1168static void
1169mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
1170			 const struct ktermios *old)
1171{
 
1172	unsigned long flags;
1173	unsigned char mr1, mr2;
1174	unsigned int j;
1175	unsigned int baud;
1176
1177	/* Prepare what we're gonna write */
1178	mr1 = 0;
1179
1180	switch (new->c_cflag & CSIZE) {
1181	case CS5:	mr1 |= MPC52xx_PSC_MODE_5_BITS;
1182		break;
1183	case CS6:	mr1 |= MPC52xx_PSC_MODE_6_BITS;
1184		break;
1185	case CS7:	mr1 |= MPC52xx_PSC_MODE_7_BITS;
1186		break;
1187	case CS8:
1188	default:	mr1 |= MPC52xx_PSC_MODE_8_BITS;
1189	}
1190
1191	if (new->c_cflag & PARENB) {
1192		if (new->c_cflag & CMSPAR)
1193			mr1 |= MPC52xx_PSC_MODE_PARFORCE;
1194
1195		/* With CMSPAR, PARODD also means high parity (same as termios) */
1196		mr1 |= (new->c_cflag & PARODD) ?
1197			MPC52xx_PSC_MODE_PARODD : MPC52xx_PSC_MODE_PAREVEN;
1198	} else {
1199		mr1 |= MPC52xx_PSC_MODE_PARNONE;
1200	}
1201
1202	mr2 = 0;
1203
1204	if (new->c_cflag & CSTOPB)
1205		mr2 |= MPC52xx_PSC_MODE_TWO_STOP;
1206	else
1207		mr2 |= ((new->c_cflag & CSIZE) == CS5) ?
1208			MPC52xx_PSC_MODE_ONE_STOP_5_BITS :
1209			MPC52xx_PSC_MODE_ONE_STOP;
1210
1211	if (new->c_cflag & CRTSCTS) {
1212		mr1 |= MPC52xx_PSC_MODE_RXRTS;
1213		mr2 |= MPC52xx_PSC_MODE_TXCTS;
1214	}
1215
1216	/* Get the lock */
1217	uart_port_lock_irqsave(port, &flags);
1218
1219	/* Do our best to flush TX & RX, so we don't lose anything */
1220	/* But we don't wait indefinitely ! */
1221	j = 5000000;	/* Maximum wait */
1222	/* FIXME Can't receive chars since set_termios might be called at early
1223	 * boot for the console, all stuff is not yet ready to receive at that
1224	 * time and that just makes the kernel oops */
1225	/* while (j-- && mpc52xx_uart_int_rx_chars(port)); */
1226	while (!mpc52xx_uart_tx_empty(port) && --j)
1227		udelay(1);
1228
1229	if (!j)
1230		printk(KERN_ERR "mpc52xx_uart.c: "
1231			"Unable to flush RX & TX fifos in-time in set_termios."
1232			"Some chars may have been lost.\n");
1233
1234	/* Reset the TX & RX */
1235	psc_ops->command(port, MPC52xx_PSC_RST_RX);
1236	psc_ops->command(port, MPC52xx_PSC_RST_TX);
1237
1238	/* Send new mode settings */
1239	psc_ops->set_mode(port, mr1, mr2);
 
 
1240	baud = psc_ops->set_baudrate(port, new, old);
1241
1242	/* Update the per-port timeout */
1243	uart_update_timeout(port, new->c_cflag, baud);
1244
1245	if (UART_ENABLE_MS(port, new->c_cflag))
1246		mpc52xx_uart_enable_ms(port);
1247
1248	/* Reenable TX & RX */
1249	psc_ops->command(port, MPC52xx_PSC_TX_ENABLE);
1250	psc_ops->command(port, MPC52xx_PSC_RX_ENABLE);
1251
1252	/* We're all set, release the lock */
1253	uart_port_unlock_irqrestore(port, flags);
1254}
1255
1256static const char *
1257mpc52xx_uart_type(struct uart_port *port)
1258{
1259	/*
1260	 * We keep using PORT_MPC52xx for historic reasons although it applies
1261	 * for MPC512x, too, but print "MPC5xxx" to not irritate users
1262	 */
1263	return port->type == PORT_MPC52xx ? "MPC5xxx PSC" : NULL;
1264}
1265
1266static void
1267mpc52xx_uart_release_port(struct uart_port *port)
1268{
1269	if (psc_ops->clock_relse)
1270		psc_ops->clock_relse(port);
1271
1272	/* remapped by us ? */
1273	if (port->flags & UPF_IOREMAP) {
1274		iounmap(port->membase);
1275		port->membase = NULL;
1276	}
1277
1278	release_mem_region(port->mapbase, sizeof(struct mpc52xx_psc));
1279}
1280
1281static int
1282mpc52xx_uart_request_port(struct uart_port *port)
1283{
1284	int err;
1285
1286	if (port->flags & UPF_IOREMAP) /* Need to remap ? */
1287		port->membase = ioremap(port->mapbase,
1288					sizeof(struct mpc52xx_psc));
1289
1290	if (!port->membase)
1291		return -EINVAL;
1292
1293	err = request_mem_region(port->mapbase, sizeof(struct mpc52xx_psc),
1294			"mpc52xx_psc_uart") != NULL ? 0 : -EBUSY;
1295
1296	if (err)
1297		goto out_membase;
1298
1299	if (psc_ops->clock_alloc) {
1300		err = psc_ops->clock_alloc(port);
1301		if (err)
1302			goto out_mapregion;
1303	}
1304
1305	return 0;
1306
1307out_mapregion:
1308	release_mem_region(port->mapbase, sizeof(struct mpc52xx_psc));
1309out_membase:
1310	if (port->flags & UPF_IOREMAP) {
1311		iounmap(port->membase);
1312		port->membase = NULL;
1313	}
 
1314	return err;
1315}
1316
1317static void
1318mpc52xx_uart_config_port(struct uart_port *port, int flags)
1319{
1320	if ((flags & UART_CONFIG_TYPE)
1321		&& (mpc52xx_uart_request_port(port) == 0))
1322		port->type = PORT_MPC52xx;
1323}
1324
1325static int
1326mpc52xx_uart_verify_port(struct uart_port *port, struct serial_struct *ser)
1327{
1328	if (ser->type != PORT_UNKNOWN && ser->type != PORT_MPC52xx)
1329		return -EINVAL;
1330
1331	if ((ser->irq != port->irq) ||
1332	    (ser->io_type != UPIO_MEM) ||
1333	    (ser->baud_base != port->uartclk)  ||
1334	    (ser->iomem_base != (void *)port->mapbase) ||
1335	    (ser->hub6 != 0))
1336		return -EINVAL;
1337
1338	return 0;
1339}
1340
1341
1342static const struct uart_ops mpc52xx_uart_ops = {
1343	.tx_empty	= mpc52xx_uart_tx_empty,
1344	.set_mctrl	= mpc52xx_uart_set_mctrl,
1345	.get_mctrl	= mpc52xx_uart_get_mctrl,
1346	.stop_tx	= mpc52xx_uart_stop_tx,
1347	.start_tx	= mpc52xx_uart_start_tx,
 
1348	.stop_rx	= mpc52xx_uart_stop_rx,
1349	.enable_ms	= mpc52xx_uart_enable_ms,
1350	.break_ctl	= mpc52xx_uart_break_ctl,
1351	.startup	= mpc52xx_uart_startup,
1352	.shutdown	= mpc52xx_uart_shutdown,
1353	.set_termios	= mpc52xx_uart_set_termios,
1354/*	.pm		= mpc52xx_uart_pm,		Not supported yet */
 
1355	.type		= mpc52xx_uart_type,
1356	.release_port	= mpc52xx_uart_release_port,
1357	.request_port	= mpc52xx_uart_request_port,
1358	.config_port	= mpc52xx_uart_config_port,
1359	.verify_port	= mpc52xx_uart_verify_port
1360};
1361
1362
1363/* ======================================================================== */
1364/* Interrupt handling                                                       */
1365/* ======================================================================== */
1366
1367static inline bool
1368mpc52xx_uart_int_rx_chars(struct uart_port *port)
1369{
1370	struct tty_port *tport = &port->state->port;
1371	unsigned char ch, flag;
1372	unsigned short status;
1373
1374	/* While we can read, do so ! */
1375	while (psc_ops->raw_rx_rdy(port)) {
1376		/* Get the char */
1377		ch = psc_ops->read_char(port);
1378
1379		/* Handle sysreq char */
1380		if (uart_handle_sysrq_char(port, ch))
 
 
1381			continue;
 
 
1382
1383		/* Store it */
1384
1385		flag = TTY_NORMAL;
1386		port->icount.rx++;
1387
1388		status = psc_ops->get_status(port);
1389
1390		if (status & (MPC52xx_PSC_SR_PE |
1391			      MPC52xx_PSC_SR_FE |
1392			      MPC52xx_PSC_SR_RB)) {
1393
1394			if (status & MPC52xx_PSC_SR_RB) {
1395				flag = TTY_BREAK;
1396				uart_handle_break(port);
1397				port->icount.brk++;
1398			} else if (status & MPC52xx_PSC_SR_PE) {
1399				flag = TTY_PARITY;
1400				port->icount.parity++;
1401			}
1402			else if (status & MPC52xx_PSC_SR_FE) {
1403				flag = TTY_FRAME;
1404				port->icount.frame++;
1405			}
1406
1407			/* Clear error condition */
1408			psc_ops->command(port, MPC52xx_PSC_RST_ERR_STAT);
1409
1410		}
1411		tty_insert_flip_char(tport, ch, flag);
1412		if (status & MPC52xx_PSC_SR_OE) {
1413			/*
1414			 * Overrun is special, since it's
1415			 * reported immediately, and doesn't
1416			 * affect the current character
1417			 */
1418			tty_insert_flip_char(tport, 0, TTY_OVERRUN);
1419			port->icount.overrun++;
1420		}
1421	}
1422
1423	tty_flip_buffer_push(tport);
 
 
1424
1425	return psc_ops->raw_rx_rdy(port);
1426}
1427
1428static inline bool
1429mpc52xx_uart_int_tx_chars(struct uart_port *port)
1430{
1431	u8 ch;
1432
1433	return uart_port_tx(port, ch,
1434		psc_ops->raw_tx_rdy(port),
1435		psc_ops->write_char(port, ch));
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1436}
1437
1438static irqreturn_t
1439mpc5xxx_uart_process_int(struct uart_port *port)
1440{
1441	unsigned long pass = ISR_PASS_LIMIT;
1442	bool keepgoing;
1443	u8 status;
1444
1445	/* While we have stuff to do, we continue */
1446	do {
1447		/* If we don't find anything to do, we stop */
1448		keepgoing = false;
1449
1450		psc_ops->rx_clr_irq(port);
1451		if (psc_ops->rx_rdy(port))
1452			keepgoing |= mpc52xx_uart_int_rx_chars(port);
1453
1454		psc_ops->tx_clr_irq(port);
1455		if (psc_ops->tx_rdy(port))
1456			keepgoing |= mpc52xx_uart_int_tx_chars(port);
1457
1458		status = psc_ops->get_ipcr(port);
1459		if (status & MPC52xx_PSC_D_DCD)
1460			uart_handle_dcd_change(port, !(status & MPC52xx_PSC_DCD));
1461
1462		if (status & MPC52xx_PSC_D_CTS)
1463			uart_handle_cts_change(port, !(status & MPC52xx_PSC_CTS));
1464
1465		/* Limit number of iteration */
1466		if (!(--pass))
1467			keepgoing = false;
1468
1469	} while (keepgoing);
1470
1471	return IRQ_HANDLED;
1472}
1473
1474static irqreturn_t
1475mpc52xx_uart_int(int irq, void *dev_id)
1476{
1477	struct uart_port *port = dev_id;
1478	irqreturn_t ret;
1479
1480	uart_port_lock(port);
1481
1482	ret = psc_ops->handle_irq(port);
1483
1484	uart_port_unlock(port);
1485
1486	return ret;
1487}
1488
1489/* ======================================================================== */
1490/* Console ( if applicable )                                                */
1491/* ======================================================================== */
1492
1493#ifdef CONFIG_SERIAL_MPC52xx_CONSOLE
1494
1495static void __init
1496mpc52xx_console_get_options(struct uart_port *port,
1497			    int *baud, int *parity, int *bits, int *flow)
1498{
 
1499	unsigned char mr1;
1500
1501	pr_debug("mpc52xx_console_get_options(port=%p)\n", port);
1502
1503	/* Read the mode registers */
1504	mr1 = psc_ops->get_mr1(port);
 
1505
1506	/* CT{U,L}R are write-only ! */
1507	*baud = CONFIG_SERIAL_MPC52xx_CONSOLE_BAUD;
1508
1509	/* Parse them */
1510	switch (mr1 & MPC52xx_PSC_MODE_BITS_MASK) {
1511	case MPC52xx_PSC_MODE_5_BITS:
1512		*bits = 5;
1513		break;
1514	case MPC52xx_PSC_MODE_6_BITS:
1515		*bits = 6;
1516		break;
1517	case MPC52xx_PSC_MODE_7_BITS:
1518		*bits = 7;
1519		break;
1520	case MPC52xx_PSC_MODE_8_BITS:
1521	default:
1522		*bits = 8;
1523	}
1524
1525	if (mr1 & MPC52xx_PSC_MODE_PARNONE)
1526		*parity = 'n';
1527	else
1528		*parity = mr1 & MPC52xx_PSC_MODE_PARODD ? 'o' : 'e';
1529}
1530
1531static void
1532mpc52xx_console_write(struct console *co, const char *s, unsigned int count)
1533{
1534	struct uart_port *port = &mpc52xx_uart_ports[co->index];
1535	unsigned int i, j;
1536
1537	/* Disable interrupts */
1538	psc_ops->cw_disable_ints(port);
1539
1540	/* Wait the TX buffer to be empty */
1541	j = 5000000;	/* Maximum wait */
1542	while (!mpc52xx_uart_tx_empty(port) && --j)
1543		udelay(1);
1544
1545	/* Write all the chars */
1546	for (i = 0; i < count; i++, s++) {
1547		/* Line return handling */
1548		if (*s == '\n')
1549			psc_ops->write_char(port, '\r');
1550
1551		/* Send the char */
1552		psc_ops->write_char(port, *s);
1553
1554		/* Wait the TX buffer to be empty */
1555		j = 20000;	/* Maximum wait */
1556		while (!mpc52xx_uart_tx_empty(port) && --j)
1557			udelay(1);
1558	}
1559
1560	/* Restore interrupt state */
1561	psc_ops->cw_restore_ints(port);
1562}
1563
1564
1565static int __init
1566mpc52xx_console_setup(struct console *co, char *options)
1567{
1568	struct uart_port *port = &mpc52xx_uart_ports[co->index];
1569	struct device_node *np = mpc52xx_uart_nodes[co->index];
1570	unsigned int uartclk;
1571	struct resource res;
1572	int ret;
1573
1574	int baud = CONFIG_SERIAL_MPC52xx_CONSOLE_BAUD;
1575	int bits = 8;
1576	int parity = 'n';
1577	int flow = 'n';
1578
1579	pr_debug("mpc52xx_console_setup co=%p, co->index=%i, options=%s\n",
1580		 co, co->index, options);
1581
1582	if ((co->index < 0) || (co->index >= MPC52xx_PSC_MAXNUM)) {
1583		pr_debug("PSC%x out of range\n", co->index);
1584		return -EINVAL;
1585	}
1586
1587	if (!np) {
1588		pr_debug("PSC%x not found in device tree\n", co->index);
1589		return -EINVAL;
1590	}
1591
1592	pr_debug("Console on ttyPSC%x is %pOF\n",
1593		 co->index, mpc52xx_uart_nodes[co->index]);
1594
1595	/* Fetch register locations */
1596	ret = of_address_to_resource(np, 0, &res);
1597	if (ret) {
1598		pr_debug("Could not get resources for PSC%x\n", co->index);
1599		return ret;
1600	}
1601
1602	uartclk = mpc5xxx_fwnode_get_bus_frequency(of_fwnode_handle(np));
1603	if (uartclk == 0) {
1604		pr_debug("Could not find uart clock frequency!\n");
1605		return -EINVAL;
1606	}
1607
1608	/* Basic port init. Needed since we use some uart_??? func before
1609	 * real init for early access */
1610	spin_lock_init(&port->lock);
1611	port->uartclk = uartclk;
1612	port->ops	= &mpc52xx_uart_ops;
1613	port->mapbase = res.start;
1614	port->membase = ioremap(res.start, sizeof(struct mpc52xx_psc));
1615	port->irq = irq_of_parse_and_map(np, 0);
1616
1617	if (port->membase == NULL)
1618		return -EINVAL;
1619
1620	pr_debug("mpc52xx-psc uart at %p, mapped to %p, irq=%x, freq=%i\n",
1621		 (void *)port->mapbase, port->membase,
1622		 port->irq, port->uartclk);
1623
1624	/* Setup the port parameters accoding to options */
1625	if (options)
1626		uart_parse_options(options, &baud, &parity, &bits, &flow);
1627	else
1628		mpc52xx_console_get_options(port, &baud, &parity, &bits, &flow);
1629
1630	pr_debug("Setting console parameters: %i %i%c1 flow=%c\n",
1631		 baud, bits, parity, flow);
1632
1633	return uart_set_options(port, co, baud, parity, bits, flow);
1634}
1635
1636
1637static struct uart_driver mpc52xx_uart_driver;
1638
1639static struct console mpc52xx_console = {
1640	.name	= "ttyPSC",
1641	.write	= mpc52xx_console_write,
1642	.device	= uart_console_device,
1643	.setup	= mpc52xx_console_setup,
1644	.flags	= CON_PRINTBUFFER,
1645	.index	= -1,	/* Specified on the cmdline (e.g. console=ttyPSC0) */
1646	.data	= &mpc52xx_uart_driver,
1647};
1648
1649
1650static int __init
1651mpc52xx_console_init(void)
1652{
1653	mpc52xx_uart_of_enumerate();
1654	register_console(&mpc52xx_console);
1655	return 0;
1656}
1657
1658console_initcall(mpc52xx_console_init);
1659
1660#define MPC52xx_PSC_CONSOLE &mpc52xx_console
1661#else
1662#define MPC52xx_PSC_CONSOLE NULL
1663#endif
1664
1665
1666/* ======================================================================== */
1667/* UART Driver                                                              */
1668/* ======================================================================== */
1669
1670static struct uart_driver mpc52xx_uart_driver = {
1671	.driver_name	= "mpc52xx_psc_uart",
1672	.dev_name	= "ttyPSC",
1673	.major		= SERIAL_PSC_MAJOR,
1674	.minor		= SERIAL_PSC_MINOR,
1675	.nr		= MPC52xx_PSC_MAXNUM,
1676	.cons		= MPC52xx_PSC_CONSOLE,
1677};
1678
1679/* ======================================================================== */
1680/* OF Platform Driver                                                       */
1681/* ======================================================================== */
1682
1683static const struct of_device_id mpc52xx_uart_of_match[] = {
1684#ifdef CONFIG_PPC_MPC52xx
1685	{ .compatible = "fsl,mpc5200b-psc-uart", .data = &mpc5200b_psc_ops, },
1686	{ .compatible = "fsl,mpc5200-psc-uart", .data = &mpc52xx_psc_ops, },
1687	/* binding used by old lite5200 device trees: */
1688	{ .compatible = "mpc5200-psc-uart", .data = &mpc52xx_psc_ops, },
1689	/* binding used by efika: */
1690	{ .compatible = "mpc5200-serial", .data = &mpc52xx_psc_ops, },
1691#endif
1692#ifdef CONFIG_PPC_MPC512x
1693	{ .compatible = "fsl,mpc5121-psc-uart", .data = &mpc512x_psc_ops, },
1694	{ .compatible = "fsl,mpc5125-psc-uart", .data = &mpc5125_psc_ops, },
1695#endif
1696	{},
1697};
1698
1699static int mpc52xx_uart_of_probe(struct platform_device *op)
1700{
1701	int idx = -1;
1702	unsigned int uartclk;
1703	struct uart_port *port = NULL;
1704	struct resource res;
1705	int ret;
1706
1707	/* Check validity & presence */
1708	for (idx = 0; idx < MPC52xx_PSC_MAXNUM; idx++)
1709		if (mpc52xx_uart_nodes[idx] == op->dev.of_node)
1710			break;
1711	if (idx >= MPC52xx_PSC_MAXNUM)
1712		return -EINVAL;
1713	pr_debug("Found %pOF assigned to ttyPSC%x\n",
1714		 mpc52xx_uart_nodes[idx], idx);
1715
1716	/* set the uart clock to the input clock of the psc, the different
1717	 * prescalers are taken into account in the set_baudrate() methods
1718	 * of the respective chip */
1719	uartclk = mpc5xxx_get_bus_frequency(&op->dev);
1720	if (uartclk == 0) {
1721		dev_dbg(&op->dev, "Could not find uart clock frequency!\n");
1722		return -EINVAL;
1723	}
1724
1725	/* Init the port structure */
1726	port = &mpc52xx_uart_ports[idx];
1727
1728	spin_lock_init(&port->lock);
1729	port->uartclk = uartclk;
1730	port->fifosize	= 512;
1731	port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_MPC52xx_CONSOLE);
1732	port->iotype	= UPIO_MEM;
1733	port->flags	= UPF_BOOT_AUTOCONF |
1734			  (uart_console(port) ? 0 : UPF_IOREMAP);
1735	port->line	= idx;
1736	port->ops	= &mpc52xx_uart_ops;
1737	port->dev	= &op->dev;
1738
1739	/* Search for IRQ and mapbase */
1740	ret = of_address_to_resource(op->dev.of_node, 0, &res);
1741	if (ret)
1742		return ret;
1743
1744	port->mapbase = res.start;
1745	if (!port->mapbase) {
1746		dev_dbg(&op->dev, "Could not allocate resources for PSC\n");
1747		return -EINVAL;
1748	}
1749
1750	psc_ops->get_irq(port, op->dev.of_node);
1751	if (port->irq == 0) {
1752		dev_dbg(&op->dev, "Could not get irq\n");
1753		return -EINVAL;
1754	}
1755
1756	dev_dbg(&op->dev, "mpc52xx-psc uart at %p, irq=%x, freq=%i\n",
1757		(void *)port->mapbase, port->irq, port->uartclk);
1758
1759	/* Add the port to the uart sub-system */
1760	ret = uart_add_one_port(&mpc52xx_uart_driver, port);
1761	if (ret)
1762		return ret;
1763
1764	platform_set_drvdata(op, (void *)port);
1765	return 0;
1766}
1767
1768static void mpc52xx_uart_of_remove(struct platform_device *op)
 
1769{
1770	struct uart_port *port = platform_get_drvdata(op);
 
1771
1772	if (port)
1773		uart_remove_one_port(&mpc52xx_uart_driver, port);
 
 
1774}
1775
1776#ifdef CONFIG_PM
1777static int
1778mpc52xx_uart_of_suspend(struct platform_device *op, pm_message_t state)
1779{
1780	struct uart_port *port = platform_get_drvdata(op);
1781
1782	if (port)
1783		uart_suspend_port(&mpc52xx_uart_driver, port);
1784
1785	return 0;
1786}
1787
1788static int
1789mpc52xx_uart_of_resume(struct platform_device *op)
1790{
1791	struct uart_port *port = platform_get_drvdata(op);
1792
1793	if (port)
1794		uart_resume_port(&mpc52xx_uart_driver, port);
1795
1796	return 0;
1797}
1798#endif
1799
1800static void
1801mpc52xx_uart_of_assign(struct device_node *np)
1802{
1803	int i;
1804
1805	/* Find the first free PSC number */
1806	for (i = 0; i < MPC52xx_PSC_MAXNUM; i++) {
1807		if (mpc52xx_uart_nodes[i] == NULL) {
1808			of_node_get(np);
1809			mpc52xx_uart_nodes[i] = np;
1810			return;
1811		}
1812	}
1813}
1814
1815static void
1816mpc52xx_uart_of_enumerate(void)
1817{
1818	static int enum_done;
1819	struct device_node *np;
1820	const struct  of_device_id *match;
1821	int i;
1822
1823	if (enum_done)
1824		return;
1825
1826	/* Assign index to each PSC in device tree */
1827	for_each_matching_node(np, mpc52xx_uart_of_match) {
1828		match = of_match_node(mpc52xx_uart_of_match, np);
1829		psc_ops = match->data;
1830		mpc52xx_uart_of_assign(np);
1831	}
1832
1833	enum_done = 1;
1834
1835	for (i = 0; i < MPC52xx_PSC_MAXNUM; i++) {
1836		if (mpc52xx_uart_nodes[i])
1837			pr_debug("%pOF assigned to ttyPSC%x\n",
1838				 mpc52xx_uart_nodes[i], i);
1839	}
1840}
1841
1842MODULE_DEVICE_TABLE(of, mpc52xx_uart_of_match);
1843
1844static struct platform_driver mpc52xx_uart_of_driver = {
1845	.probe		= mpc52xx_uart_of_probe,
1846	.remove_new	= mpc52xx_uart_of_remove,
1847#ifdef CONFIG_PM
1848	.suspend	= mpc52xx_uart_of_suspend,
1849	.resume		= mpc52xx_uart_of_resume,
1850#endif
1851	.driver = {
1852		.name = "mpc52xx-psc-uart",
 
1853		.of_match_table = mpc52xx_uart_of_match,
1854	},
1855};
1856
1857
1858/* ======================================================================== */
1859/* Module                                                                   */
1860/* ======================================================================== */
1861
1862static int __init
1863mpc52xx_uart_init(void)
1864{
1865	int ret;
1866
1867	printk(KERN_INFO "Serial: MPC52xx PSC UART driver\n");
1868
1869	ret = uart_register_driver(&mpc52xx_uart_driver);
1870	if (ret) {
1871		printk(KERN_ERR "%s: uart_register_driver failed (%i)\n",
1872		       __FILE__, ret);
1873		return ret;
1874	}
1875
1876	mpc52xx_uart_of_enumerate();
1877
1878	/*
1879	 * Map the PSC FIFO Controller and init if on MPC512x.
1880	 */
1881	if (psc_ops && psc_ops->fifoc_init) {
1882		ret = psc_ops->fifoc_init();
1883		if (ret)
1884			goto err_init;
1885	}
1886
1887	ret = platform_driver_register(&mpc52xx_uart_of_driver);
1888	if (ret) {
1889		printk(KERN_ERR "%s: platform_driver_register failed (%i)\n",
1890		       __FILE__, ret);
1891		goto err_reg;
 
1892	}
1893
1894	return 0;
1895err_reg:
1896	if (psc_ops && psc_ops->fifoc_uninit)
1897		psc_ops->fifoc_uninit();
1898err_init:
1899	uart_unregister_driver(&mpc52xx_uart_driver);
1900	return ret;
1901}
1902
1903static void __exit
1904mpc52xx_uart_exit(void)
1905{
1906	if (psc_ops->fifoc_uninit)
1907		psc_ops->fifoc_uninit();
1908
1909	platform_driver_unregister(&mpc52xx_uart_of_driver);
1910	uart_unregister_driver(&mpc52xx_uart_driver);
1911}
1912
1913
1914module_init(mpc52xx_uart_init);
1915module_exit(mpc52xx_uart_exit);
1916
1917MODULE_AUTHOR("Sylvain Munaut <tnt@246tNt.com>");
1918MODULE_DESCRIPTION("Freescale MPC52xx PSC UART");
1919MODULE_LICENSE("GPL");