Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Copyright (C) 2008 Per Dalen <per.dalen@cnw.se>
4 *
5 * Parts of this software are based on (derived) the following:
6 *
7 * - Kvaser linux driver, version 4.72 BETA
8 * Copyright (C) 2002-2007 KVASER AB
9 *
10 * - Lincan driver, version 0.3.3, OCERA project
11 * Copyright (C) 2004 Pavel Pisa
12 * Copyright (C) 2001 Arnaud Westenberg
13 *
14 * - Socketcan SJA1000 drivers
15 * Copyright (C) 2007 Wolfgang Grandegger <wg@grandegger.com>
16 * Copyright (c) 2002-2007 Volkswagen Group Electronic Research
17 * Copyright (c) 2003 Matthias Brukner, Trajet Gmbh, Rebenring 33,
18 * 38106 Braunschweig, GERMANY
19 */
20
21#include <linux/kernel.h>
22#include <linux/module.h>
23#include <linux/interrupt.h>
24#include <linux/netdevice.h>
25#include <linux/delay.h>
26#include <linux/pci.h>
27#include <linux/can/dev.h>
28#include <linux/io.h>
29
30#include "sja1000.h"
31
32#define DRV_NAME "kvaser_pci"
33
34MODULE_AUTHOR("Per Dalen <per.dalen@cnw.se>");
35MODULE_DESCRIPTION("Socket-CAN driver for KVASER PCAN PCI cards");
36MODULE_LICENSE("GPL v2");
37
38#define MAX_NO_OF_CHANNELS 4 /* max no of channels on a single card */
39
40struct kvaser_pci {
41 int channel;
42 struct pci_dev *pci_dev;
43 struct net_device *slave_dev[MAX_NO_OF_CHANNELS-1];
44 void __iomem *conf_addr;
45 void __iomem *res_addr;
46 int no_channels;
47 u8 xilinx_ver;
48};
49
50#define KVASER_PCI_CAN_CLOCK (16000000 / 2)
51
52/*
53 * The board configuration is probably following:
54 * RX1 is connected to ground.
55 * TX1 is not connected.
56 * CLKO is not connected.
57 * Setting the OCR register to 0xDA is a good idea.
58 * This means normal output mode , push-pull and the correct polarity.
59 */
60#define KVASER_PCI_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
61
62/*
63 * In the CDR register, you should set CBP to 1.
64 * You will probably also want to set the clock divider value to 0
65 * (meaning divide-by-2), the Pelican bit, and the clock-off bit
66 * (you will have no need for CLKOUT anyway).
67 */
68#define KVASER_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
69
70/*
71 * These register values are valid for revision 14 of the Xilinx logic.
72 */
73#define XILINX_VERINT 7 /* Lower nibble simulate interrupts,
74 high nibble version number. */
75
76#define XILINX_PRESUMED_VERSION 14
77
78/*
79 * Important S5920 registers
80 */
81#define S5920_INTCSR 0x38
82#define S5920_PTCR 0x60
83#define INTCSR_ADDON_INTENABLE_M 0x2000
84
85
86#define KVASER_PCI_PORT_BYTES 0x20
87
88#define PCI_CONFIG_PORT_SIZE 0x80 /* size of the config io-memory */
89#define PCI_PORT_SIZE 0x80 /* size of a channel io-memory */
90#define PCI_PORT_XILINX_SIZE 0x08 /* size of a xilinx io-memory */
91
92#define KVASER_PCI_VENDOR_ID1 0x10e8 /* the PCI device and vendor IDs */
93#define KVASER_PCI_DEVICE_ID1 0x8406
94
95#define KVASER_PCI_VENDOR_ID2 0x1a07 /* the PCI device and vendor IDs */
96#define KVASER_PCI_DEVICE_ID2 0x0008
97
98static const struct pci_device_id kvaser_pci_tbl[] = {
99 {KVASER_PCI_VENDOR_ID1, KVASER_PCI_DEVICE_ID1, PCI_ANY_ID, PCI_ANY_ID,},
100 {KVASER_PCI_VENDOR_ID2, KVASER_PCI_DEVICE_ID2, PCI_ANY_ID, PCI_ANY_ID,},
101 { 0,}
102};
103
104MODULE_DEVICE_TABLE(pci, kvaser_pci_tbl);
105
106static u8 kvaser_pci_read_reg(const struct sja1000_priv *priv, int port)
107{
108 return ioread8(priv->reg_base + port);
109}
110
111static void kvaser_pci_write_reg(const struct sja1000_priv *priv,
112 int port, u8 val)
113{
114 iowrite8(val, priv->reg_base + port);
115}
116
117static void kvaser_pci_disable_irq(struct net_device *dev)
118{
119 struct sja1000_priv *priv = netdev_priv(dev);
120 struct kvaser_pci *board = priv->priv;
121 u32 intcsr;
122
123 /* Disable interrupts from card */
124 intcsr = ioread32(board->conf_addr + S5920_INTCSR);
125 intcsr &= ~INTCSR_ADDON_INTENABLE_M;
126 iowrite32(intcsr, board->conf_addr + S5920_INTCSR);
127}
128
129static void kvaser_pci_enable_irq(struct net_device *dev)
130{
131 struct sja1000_priv *priv = netdev_priv(dev);
132 struct kvaser_pci *board = priv->priv;
133 u32 tmp_en_io;
134
135 /* Enable interrupts from card */
136 tmp_en_io = ioread32(board->conf_addr + S5920_INTCSR);
137 tmp_en_io |= INTCSR_ADDON_INTENABLE_M;
138 iowrite32(tmp_en_io, board->conf_addr + S5920_INTCSR);
139}
140
141static int number_of_sja1000_chip(void __iomem *base_addr)
142{
143 u8 status;
144 int i;
145
146 for (i = 0; i < MAX_NO_OF_CHANNELS; i++) {
147 /* reset chip */
148 iowrite8(MOD_RM, base_addr +
149 (i * KVASER_PCI_PORT_BYTES) + SJA1000_MOD);
150 status = ioread8(base_addr +
151 (i * KVASER_PCI_PORT_BYTES) + SJA1000_MOD);
152 /* check reset bit */
153 if (!(status & MOD_RM))
154 break;
155 }
156
157 return i;
158}
159
160static void kvaser_pci_del_chan(struct net_device *dev)
161{
162 struct sja1000_priv *priv;
163 struct kvaser_pci *board;
164 int i;
165
166 if (!dev)
167 return;
168 priv = netdev_priv(dev);
169 board = priv->priv;
170 if (!board)
171 return;
172
173 dev_info(&board->pci_dev->dev, "Removing device %s\n",
174 dev->name);
175
176 /* Disable PCI interrupts */
177 kvaser_pci_disable_irq(dev);
178
179 for (i = 0; i < board->no_channels - 1; i++) {
180 if (board->slave_dev[i]) {
181 dev_info(&board->pci_dev->dev, "Removing device %s\n",
182 board->slave_dev[i]->name);
183 unregister_sja1000dev(board->slave_dev[i]);
184 free_sja1000dev(board->slave_dev[i]);
185 }
186 }
187 unregister_sja1000dev(dev);
188
189 pci_iounmap(board->pci_dev, priv->reg_base);
190 pci_iounmap(board->pci_dev, board->conf_addr);
191 pci_iounmap(board->pci_dev, board->res_addr);
192
193 free_sja1000dev(dev);
194}
195
196static int kvaser_pci_add_chan(struct pci_dev *pdev, int channel,
197 struct net_device **master_dev,
198 void __iomem *conf_addr,
199 void __iomem *res_addr,
200 void __iomem *base_addr)
201{
202 struct net_device *dev;
203 struct sja1000_priv *priv;
204 struct kvaser_pci *board;
205 int err;
206
207 dev = alloc_sja1000dev(sizeof(struct kvaser_pci));
208 if (dev == NULL)
209 return -ENOMEM;
210
211 priv = netdev_priv(dev);
212 board = priv->priv;
213
214 board->pci_dev = pdev;
215 board->channel = channel;
216
217 /* S5920 */
218 board->conf_addr = conf_addr;
219
220 /* XILINX board wide address */
221 board->res_addr = res_addr;
222
223 if (channel == 0) {
224 board->xilinx_ver =
225 ioread8(board->res_addr + XILINX_VERINT) >> 4;
226
227 /* Assert PTADR# - we're in passive mode so the other bits are
228 not important */
229 iowrite32(0x80808080UL, board->conf_addr + S5920_PTCR);
230
231 /* Enable interrupts from card */
232 kvaser_pci_enable_irq(dev);
233 } else {
234 struct sja1000_priv *master_priv = netdev_priv(*master_dev);
235 struct kvaser_pci *master_board = master_priv->priv;
236 master_board->slave_dev[channel - 1] = dev;
237 master_board->no_channels = channel + 1;
238 board->xilinx_ver = master_board->xilinx_ver;
239 }
240
241 priv->reg_base = base_addr + channel * KVASER_PCI_PORT_BYTES;
242
243 priv->read_reg = kvaser_pci_read_reg;
244 priv->write_reg = kvaser_pci_write_reg;
245
246 priv->can.clock.freq = KVASER_PCI_CAN_CLOCK;
247
248 priv->ocr = KVASER_PCI_OCR;
249 priv->cdr = KVASER_PCI_CDR;
250
251 priv->irq_flags = IRQF_SHARED;
252 dev->irq = pdev->irq;
253
254 dev_info(&pdev->dev, "reg_base=%p conf_addr=%p irq=%d\n",
255 priv->reg_base, board->conf_addr, dev->irq);
256
257 SET_NETDEV_DEV(dev, &pdev->dev);
258 dev->dev_id = channel;
259
260 /* Register SJA1000 device */
261 err = register_sja1000dev(dev);
262 if (err) {
263 dev_err(&pdev->dev, "Registering device failed (err=%d)\n",
264 err);
265 goto failure;
266 }
267
268 if (channel == 0)
269 *master_dev = dev;
270
271 return 0;
272
273failure:
274 kvaser_pci_del_chan(dev);
275 return err;
276}
277
278static int kvaser_pci_init_one(struct pci_dev *pdev,
279 const struct pci_device_id *ent)
280{
281 int err;
282 struct net_device *master_dev = NULL;
283 struct sja1000_priv *priv;
284 struct kvaser_pci *board;
285 int no_channels;
286 void __iomem *base_addr = NULL;
287 void __iomem *conf_addr = NULL;
288 void __iomem *res_addr = NULL;
289 int i;
290
291 dev_info(&pdev->dev, "initializing device %04x:%04x\n",
292 pdev->vendor, pdev->device);
293
294 err = pci_enable_device(pdev);
295 if (err)
296 goto failure;
297
298 err = pci_request_regions(pdev, DRV_NAME);
299 if (err)
300 goto failure_release_pci;
301
302 /* S5920 */
303 conf_addr = pci_iomap(pdev, 0, PCI_CONFIG_PORT_SIZE);
304 if (conf_addr == NULL) {
305 err = -ENODEV;
306 goto failure_release_regions;
307 }
308
309 /* XILINX board wide address */
310 res_addr = pci_iomap(pdev, 2, PCI_PORT_XILINX_SIZE);
311 if (res_addr == NULL) {
312 err = -ENOMEM;
313 goto failure_iounmap;
314 }
315
316 base_addr = pci_iomap(pdev, 1, PCI_PORT_SIZE);
317 if (base_addr == NULL) {
318 err = -ENOMEM;
319 goto failure_iounmap;
320 }
321
322 no_channels = number_of_sja1000_chip(base_addr);
323 if (no_channels == 0) {
324 err = -ENOMEM;
325 goto failure_iounmap;
326 }
327
328 for (i = 0; i < no_channels; i++) {
329 err = kvaser_pci_add_chan(pdev, i, &master_dev,
330 conf_addr, res_addr,
331 base_addr);
332 if (err)
333 goto failure_cleanup;
334 }
335
336 priv = netdev_priv(master_dev);
337 board = priv->priv;
338
339 dev_info(&pdev->dev, "xilinx version=%d number of channels=%d\n",
340 board->xilinx_ver, board->no_channels);
341
342 pci_set_drvdata(pdev, master_dev);
343 return 0;
344
345failure_cleanup:
346 kvaser_pci_del_chan(master_dev);
347
348failure_iounmap:
349 if (conf_addr != NULL)
350 pci_iounmap(pdev, conf_addr);
351 if (res_addr != NULL)
352 pci_iounmap(pdev, res_addr);
353 if (base_addr != NULL)
354 pci_iounmap(pdev, base_addr);
355
356failure_release_regions:
357 pci_release_regions(pdev);
358
359failure_release_pci:
360 pci_disable_device(pdev);
361
362failure:
363 return err;
364
365}
366
367static void kvaser_pci_remove_one(struct pci_dev *pdev)
368{
369 struct net_device *dev = pci_get_drvdata(pdev);
370
371 kvaser_pci_del_chan(dev);
372
373 pci_release_regions(pdev);
374 pci_disable_device(pdev);
375}
376
377static struct pci_driver kvaser_pci_driver = {
378 .name = DRV_NAME,
379 .id_table = kvaser_pci_tbl,
380 .probe = kvaser_pci_init_one,
381 .remove = kvaser_pci_remove_one,
382};
383
384module_pci_driver(kvaser_pci_driver);
1/*
2 * Copyright (C) 2008 Per Dalen <per.dalen@cnw.se>
3 *
4 * Parts of this software are based on (derived) the following:
5 *
6 * - Kvaser linux driver, version 4.72 BETA
7 * Copyright (C) 2002-2007 KVASER AB
8 *
9 * - Lincan driver, version 0.3.3, OCERA project
10 * Copyright (C) 2004 Pavel Pisa
11 * Copyright (C) 2001 Arnaud Westenberg
12 *
13 * - Socketcan SJA1000 drivers
14 * Copyright (C) 2007 Wolfgang Grandegger <wg@grandegger.com>
15 * Copyright (c) 2002-2007 Volkswagen Group Electronic Research
16 * Copyright (c) 2003 Matthias Brukner, Trajet Gmbh, Rebenring 33,
17 * 38106 Braunschweig, GERMANY
18 *
19 * This program is free software; you can redistribute it and/or modify
20 * it under the terms of the version 2 of the GNU General Public License
21 * as published by the Free Software Foundation
22 *
23 * This program is distributed in the hope that it will be useful, but
24 * WITHOUT ANY WARRANTY; without even the implied warranty of
25 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
26 * General Public License for more details.
27 *
28 * You should have received a copy of the GNU General Public License
29 * along with this program; if not, write to the Free Software Foundation,
30 * Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
31 */
32
33#include <linux/kernel.h>
34#include <linux/module.h>
35#include <linux/interrupt.h>
36#include <linux/netdevice.h>
37#include <linux/delay.h>
38#include <linux/pci.h>
39#include <linux/can/dev.h>
40#include <linux/io.h>
41
42#include "sja1000.h"
43
44#define DRV_NAME "kvaser_pci"
45
46MODULE_AUTHOR("Per Dalen <per.dalen@cnw.se>");
47MODULE_DESCRIPTION("Socket-CAN driver for KVASER PCAN PCI cards");
48MODULE_SUPPORTED_DEVICE("KVASER PCAN PCI CAN card");
49MODULE_LICENSE("GPL v2");
50
51#define MAX_NO_OF_CHANNELS 4 /* max no of channels on a single card */
52
53struct kvaser_pci {
54 int channel;
55 struct pci_dev *pci_dev;
56 struct net_device *slave_dev[MAX_NO_OF_CHANNELS-1];
57 void __iomem *conf_addr;
58 void __iomem *res_addr;
59 int no_channels;
60 u8 xilinx_ver;
61};
62
63#define KVASER_PCI_CAN_CLOCK (16000000 / 2)
64
65/*
66 * The board configuration is probably following:
67 * RX1 is connected to ground.
68 * TX1 is not connected.
69 * CLKO is not connected.
70 * Setting the OCR register to 0xDA is a good idea.
71 * This means normal output mode , push-pull and the correct polarity.
72 */
73#define KVASER_PCI_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
74
75/*
76 * In the CDR register, you should set CBP to 1.
77 * You will probably also want to set the clock divider value to 0
78 * (meaning divide-by-2), the Pelican bit, and the clock-off bit
79 * (you will have no need for CLKOUT anyway).
80 */
81#define KVASER_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
82
83/*
84 * These register values are valid for revision 14 of the Xilinx logic.
85 */
86#define XILINX_VERINT 7 /* Lower nibble simulate interrupts,
87 high nibble version number. */
88
89#define XILINX_PRESUMED_VERSION 14
90
91/*
92 * Important S5920 registers
93 */
94#define S5920_INTCSR 0x38
95#define S5920_PTCR 0x60
96#define INTCSR_ADDON_INTENABLE_M 0x2000
97
98
99#define KVASER_PCI_PORT_BYTES 0x20
100
101#define PCI_CONFIG_PORT_SIZE 0x80 /* size of the config io-memory */
102#define PCI_PORT_SIZE 0x80 /* size of a channel io-memory */
103#define PCI_PORT_XILINX_SIZE 0x08 /* size of a xilinx io-memory */
104
105#define KVASER_PCI_VENDOR_ID1 0x10e8 /* the PCI device and vendor IDs */
106#define KVASER_PCI_DEVICE_ID1 0x8406
107
108#define KVASER_PCI_VENDOR_ID2 0x1a07 /* the PCI device and vendor IDs */
109#define KVASER_PCI_DEVICE_ID2 0x0008
110
111static DEFINE_PCI_DEVICE_TABLE(kvaser_pci_tbl) = {
112 {KVASER_PCI_VENDOR_ID1, KVASER_PCI_DEVICE_ID1, PCI_ANY_ID, PCI_ANY_ID,},
113 {KVASER_PCI_VENDOR_ID2, KVASER_PCI_DEVICE_ID2, PCI_ANY_ID, PCI_ANY_ID,},
114 { 0,}
115};
116
117MODULE_DEVICE_TABLE(pci, kvaser_pci_tbl);
118
119static u8 kvaser_pci_read_reg(const struct sja1000_priv *priv, int port)
120{
121 return ioread8(priv->reg_base + port);
122}
123
124static void kvaser_pci_write_reg(const struct sja1000_priv *priv,
125 int port, u8 val)
126{
127 iowrite8(val, priv->reg_base + port);
128}
129
130static void kvaser_pci_disable_irq(struct net_device *dev)
131{
132 struct sja1000_priv *priv = netdev_priv(dev);
133 struct kvaser_pci *board = priv->priv;
134 u32 intcsr;
135
136 /* Disable interrupts from card */
137 intcsr = ioread32(board->conf_addr + S5920_INTCSR);
138 intcsr &= ~INTCSR_ADDON_INTENABLE_M;
139 iowrite32(intcsr, board->conf_addr + S5920_INTCSR);
140}
141
142static void kvaser_pci_enable_irq(struct net_device *dev)
143{
144 struct sja1000_priv *priv = netdev_priv(dev);
145 struct kvaser_pci *board = priv->priv;
146 u32 tmp_en_io;
147
148 /* Enable interrupts from card */
149 tmp_en_io = ioread32(board->conf_addr + S5920_INTCSR);
150 tmp_en_io |= INTCSR_ADDON_INTENABLE_M;
151 iowrite32(tmp_en_io, board->conf_addr + S5920_INTCSR);
152}
153
154static int number_of_sja1000_chip(void __iomem *base_addr)
155{
156 u8 status;
157 int i;
158
159 for (i = 0; i < MAX_NO_OF_CHANNELS; i++) {
160 /* reset chip */
161 iowrite8(MOD_RM, base_addr +
162 (i * KVASER_PCI_PORT_BYTES) + REG_MOD);
163 status = ioread8(base_addr +
164 (i * KVASER_PCI_PORT_BYTES) + REG_MOD);
165 /* check reset bit */
166 if (!(status & MOD_RM))
167 break;
168 }
169
170 return i;
171}
172
173static void kvaser_pci_del_chan(struct net_device *dev)
174{
175 struct sja1000_priv *priv;
176 struct kvaser_pci *board;
177 int i;
178
179 if (!dev)
180 return;
181 priv = netdev_priv(dev);
182 board = priv->priv;
183 if (!board)
184 return;
185
186 dev_info(&board->pci_dev->dev, "Removing device %s\n",
187 dev->name);
188
189 /* Disable PCI interrupts */
190 kvaser_pci_disable_irq(dev);
191
192 for (i = 0; i < board->no_channels - 1; i++) {
193 if (board->slave_dev[i]) {
194 dev_info(&board->pci_dev->dev, "Removing device %s\n",
195 board->slave_dev[i]->name);
196 unregister_sja1000dev(board->slave_dev[i]);
197 free_sja1000dev(board->slave_dev[i]);
198 }
199 }
200 unregister_sja1000dev(dev);
201
202 pci_iounmap(board->pci_dev, priv->reg_base);
203 pci_iounmap(board->pci_dev, board->conf_addr);
204 pci_iounmap(board->pci_dev, board->res_addr);
205
206 free_sja1000dev(dev);
207}
208
209static int kvaser_pci_add_chan(struct pci_dev *pdev, int channel,
210 struct net_device **master_dev,
211 void __iomem *conf_addr,
212 void __iomem *res_addr,
213 void __iomem *base_addr)
214{
215 struct net_device *dev;
216 struct sja1000_priv *priv;
217 struct kvaser_pci *board;
218 int err, init_step;
219
220 dev = alloc_sja1000dev(sizeof(struct kvaser_pci));
221 if (dev == NULL)
222 return -ENOMEM;
223
224 priv = netdev_priv(dev);
225 board = priv->priv;
226
227 board->pci_dev = pdev;
228 board->channel = channel;
229
230 /* S5920 */
231 board->conf_addr = conf_addr;
232
233 /* XILINX board wide address */
234 board->res_addr = res_addr;
235
236 if (channel == 0) {
237 board->xilinx_ver =
238 ioread8(board->res_addr + XILINX_VERINT) >> 4;
239 init_step = 2;
240
241 /* Assert PTADR# - we're in passive mode so the other bits are
242 not important */
243 iowrite32(0x80808080UL, board->conf_addr + S5920_PTCR);
244
245 /* Enable interrupts from card */
246 kvaser_pci_enable_irq(dev);
247 } else {
248 struct sja1000_priv *master_priv = netdev_priv(*master_dev);
249 struct kvaser_pci *master_board = master_priv->priv;
250 master_board->slave_dev[channel - 1] = dev;
251 master_board->no_channels = channel + 1;
252 board->xilinx_ver = master_board->xilinx_ver;
253 }
254
255 priv->reg_base = base_addr + channel * KVASER_PCI_PORT_BYTES;
256
257 priv->read_reg = kvaser_pci_read_reg;
258 priv->write_reg = kvaser_pci_write_reg;
259
260 priv->can.clock.freq = KVASER_PCI_CAN_CLOCK;
261
262 priv->ocr = KVASER_PCI_OCR;
263 priv->cdr = KVASER_PCI_CDR;
264
265 priv->irq_flags = IRQF_SHARED;
266 dev->irq = pdev->irq;
267
268 init_step = 4;
269
270 dev_info(&pdev->dev, "reg_base=%p conf_addr=%p irq=%d\n",
271 priv->reg_base, board->conf_addr, dev->irq);
272
273 SET_NETDEV_DEV(dev, &pdev->dev);
274
275 /* Register SJA1000 device */
276 err = register_sja1000dev(dev);
277 if (err) {
278 dev_err(&pdev->dev, "Registering device failed (err=%d)\n",
279 err);
280 goto failure;
281 }
282
283 if (channel == 0)
284 *master_dev = dev;
285
286 return 0;
287
288failure:
289 kvaser_pci_del_chan(dev);
290 return err;
291}
292
293static int __devinit kvaser_pci_init_one(struct pci_dev *pdev,
294 const struct pci_device_id *ent)
295{
296 int err;
297 struct net_device *master_dev = NULL;
298 struct sja1000_priv *priv;
299 struct kvaser_pci *board;
300 int no_channels;
301 void __iomem *base_addr = NULL;
302 void __iomem *conf_addr = NULL;
303 void __iomem *res_addr = NULL;
304 int i;
305
306 dev_info(&pdev->dev, "initializing device %04x:%04x\n",
307 pdev->vendor, pdev->device);
308
309 err = pci_enable_device(pdev);
310 if (err)
311 goto failure;
312
313 err = pci_request_regions(pdev, DRV_NAME);
314 if (err)
315 goto failure_release_pci;
316
317 /* S5920 */
318 conf_addr = pci_iomap(pdev, 0, PCI_CONFIG_PORT_SIZE);
319 if (conf_addr == NULL) {
320 err = -ENODEV;
321 goto failure_release_regions;
322 }
323
324 /* XILINX board wide address */
325 res_addr = pci_iomap(pdev, 2, PCI_PORT_XILINX_SIZE);
326 if (res_addr == NULL) {
327 err = -ENOMEM;
328 goto failure_iounmap;
329 }
330
331 base_addr = pci_iomap(pdev, 1, PCI_PORT_SIZE);
332 if (base_addr == NULL) {
333 err = -ENOMEM;
334 goto failure_iounmap;
335 }
336
337 no_channels = number_of_sja1000_chip(base_addr);
338 if (no_channels == 0) {
339 err = -ENOMEM;
340 goto failure_iounmap;
341 }
342
343 for (i = 0; i < no_channels; i++) {
344 err = kvaser_pci_add_chan(pdev, i, &master_dev,
345 conf_addr, res_addr,
346 base_addr);
347 if (err)
348 goto failure_cleanup;
349 }
350
351 priv = netdev_priv(master_dev);
352 board = priv->priv;
353
354 dev_info(&pdev->dev, "xilinx version=%d number of channels=%d\n",
355 board->xilinx_ver, board->no_channels);
356
357 pci_set_drvdata(pdev, master_dev);
358 return 0;
359
360failure_cleanup:
361 kvaser_pci_del_chan(master_dev);
362
363failure_iounmap:
364 if (conf_addr != NULL)
365 pci_iounmap(pdev, conf_addr);
366 if (res_addr != NULL)
367 pci_iounmap(pdev, res_addr);
368 if (base_addr != NULL)
369 pci_iounmap(pdev, base_addr);
370
371failure_release_regions:
372 pci_release_regions(pdev);
373
374failure_release_pci:
375 pci_disable_device(pdev);
376
377failure:
378 return err;
379
380}
381
382static void __devexit kvaser_pci_remove_one(struct pci_dev *pdev)
383{
384 struct net_device *dev = pci_get_drvdata(pdev);
385
386 kvaser_pci_del_chan(dev);
387
388 pci_release_regions(pdev);
389 pci_disable_device(pdev);
390 pci_set_drvdata(pdev, NULL);
391}
392
393static struct pci_driver kvaser_pci_driver = {
394 .name = DRV_NAME,
395 .id_table = kvaser_pci_tbl,
396 .probe = kvaser_pci_init_one,
397 .remove = __devexit_p(kvaser_pci_remove_one),
398};
399
400static int __init kvaser_pci_init(void)
401{
402 return pci_register_driver(&kvaser_pci_driver);
403}
404
405static void __exit kvaser_pci_exit(void)
406{
407 pci_unregister_driver(&kvaser_pci_driver);
408}
409
410module_init(kvaser_pci_init);
411module_exit(kvaser_pci_exit);