Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Libata driver for the highpoint 366 and 368 UDMA66 ATA controllers.
4 *
5 * This driver is heavily based upon:
6 *
7 * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003
8 *
9 * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
10 * Portions Copyright (C) 2001 Sun Microsystems, Inc.
11 * Portions Copyright (C) 2003 Red Hat Inc
12 *
13 *
14 * TODO
15 * Look into engine reset on timeout errors. Should not be required.
16 */
17#include <linux/kernel.h>
18#include <linux/module.h>
19#include <linux/pci.h>
20#include <linux/blkdev.h>
21#include <linux/delay.h>
22#include <scsi/scsi_host.h>
23#include <linux/libata.h>
24
25#define DRV_NAME "pata_hpt366"
26#define DRV_VERSION "0.6.13"
27
28struct hpt_clock {
29 u8 xfer_mode;
30 u32 timing;
31};
32
33/* key for bus clock timings
34 * bit
35 * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
36 * cycles = value + 1
37 * 4:7 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
38 * cycles = value + 1
39 * 8:11 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
40 * register access.
41 * 12:15 cmd_low_time. Active time of DIOW_/DIOR_ during task file
42 * register access.
43 * 16:18 udma_cycle_time. Clock cycles for UDMA xfer?
44 * 19:21 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
45 * 22:24 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
46 * register access.
47 * 28 UDMA enable.
48 * 29 DMA enable.
49 * 30 PIO_MST enable. If set, the chip is in bus master mode during
50 * PIO xfer.
51 * 31 FIFO enable.
52 */
53
54static const struct hpt_clock hpt366_40[] = {
55 { XFER_UDMA_4, 0x900fd943 },
56 { XFER_UDMA_3, 0x900ad943 },
57 { XFER_UDMA_2, 0x900bd943 },
58 { XFER_UDMA_1, 0x9008d943 },
59 { XFER_UDMA_0, 0x9008d943 },
60
61 { XFER_MW_DMA_2, 0xa008d943 },
62 { XFER_MW_DMA_1, 0xa010d955 },
63 { XFER_MW_DMA_0, 0xa010d9fc },
64
65 { XFER_PIO_4, 0xc008d963 },
66 { XFER_PIO_3, 0xc010d974 },
67 { XFER_PIO_2, 0xc010d997 },
68 { XFER_PIO_1, 0xc010d9c7 },
69 { XFER_PIO_0, 0xc018d9d9 },
70 { 0, 0x0120d9d9 }
71};
72
73static const struct hpt_clock hpt366_33[] = {
74 { XFER_UDMA_4, 0x90c9a731 },
75 { XFER_UDMA_3, 0x90cfa731 },
76 { XFER_UDMA_2, 0x90caa731 },
77 { XFER_UDMA_1, 0x90cba731 },
78 { XFER_UDMA_0, 0x90c8a731 },
79
80 { XFER_MW_DMA_2, 0xa0c8a731 },
81 { XFER_MW_DMA_1, 0xa0c8a732 }, /* 0xa0c8a733 */
82 { XFER_MW_DMA_0, 0xa0c8a797 },
83
84 { XFER_PIO_4, 0xc0c8a731 },
85 { XFER_PIO_3, 0xc0c8a742 },
86 { XFER_PIO_2, 0xc0d0a753 },
87 { XFER_PIO_1, 0xc0d0a7a3 }, /* 0xc0d0a793 */
88 { XFER_PIO_0, 0xc0d0a7aa }, /* 0xc0d0a7a7 */
89 { 0, 0x0120a7a7 }
90};
91
92static const struct hpt_clock hpt366_25[] = {
93 { XFER_UDMA_4, 0x90c98521 },
94 { XFER_UDMA_3, 0x90cf8521 },
95 { XFER_UDMA_2, 0x90cf8521 },
96 { XFER_UDMA_1, 0x90cb8521 },
97 { XFER_UDMA_0, 0x90cb8521 },
98
99 { XFER_MW_DMA_2, 0xa0ca8521 },
100 { XFER_MW_DMA_1, 0xa0ca8532 },
101 { XFER_MW_DMA_0, 0xa0ca8575 },
102
103 { XFER_PIO_4, 0xc0ca8521 },
104 { XFER_PIO_3, 0xc0ca8532 },
105 { XFER_PIO_2, 0xc0ca8542 },
106 { XFER_PIO_1, 0xc0d08572 },
107 { XFER_PIO_0, 0xc0d08585 },
108 { 0, 0x01208585 }
109};
110
111/**
112 * hpt36x_find_mode - find the hpt36x timing
113 * @ap: ATA port
114 * @speed: transfer mode
115 *
116 * Return the 32bit register programming information for this channel
117 * that matches the speed provided.
118 */
119
120static u32 hpt36x_find_mode(struct ata_port *ap, int speed)
121{
122 struct hpt_clock *clocks = ap->host->private_data;
123
124 while (clocks->xfer_mode) {
125 if (clocks->xfer_mode == speed)
126 return clocks->timing;
127 clocks++;
128 }
129 BUG();
130 return 0xffffffffU; /* silence compiler warning */
131}
132
133static const char * const bad_ata33[] = {
134 "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3",
135 "Maxtor 90845U3", "Maxtor 90650U2",
136 "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5",
137 "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
138 "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6",
139 "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
140 "Maxtor 90510D4",
141 "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
142 "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7",
143 "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
144 "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5",
145 "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
146 NULL
147};
148
149static const char * const bad_ata66_4[] = {
150 "IBM-DTLA-307075",
151 "IBM-DTLA-307060",
152 "IBM-DTLA-307045",
153 "IBM-DTLA-307030",
154 "IBM-DTLA-307020",
155 "IBM-DTLA-307015",
156 "IBM-DTLA-305040",
157 "IBM-DTLA-305030",
158 "IBM-DTLA-305020",
159 "IC35L010AVER07-0",
160 "IC35L020AVER07-0",
161 "IC35L030AVER07-0",
162 "IC35L040AVER07-0",
163 "IC35L060AVER07-0",
164 "WDC AC310200R",
165 NULL
166};
167
168static const char * const bad_ata66_3[] = {
169 "WDC AC310200R",
170 NULL
171};
172
173static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr,
174 const char * const list[])
175{
176 unsigned char model_num[ATA_ID_PROD_LEN + 1];
177 int i;
178
179 ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));
180
181 i = match_string(list, -1, model_num);
182 if (i >= 0) {
183 ata_dev_warn(dev, "%s is not supported for %s\n", modestr, list[i]);
184 return 1;
185 }
186 return 0;
187}
188
189/**
190 * hpt366_filter - mode selection filter
191 * @adev: ATA device
192 * @mask: Current mask to manipulate and pass back
193 *
194 * Block UDMA on devices that cause trouble with this controller.
195 */
196
197static unsigned int hpt366_filter(struct ata_device *adev, unsigned int mask)
198{
199 if (adev->class == ATA_DEV_ATA) {
200 if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33))
201 mask &= ~ATA_MASK_UDMA;
202 if (hpt_dma_blacklisted(adev, "UDMA3", bad_ata66_3))
203 mask &= ~(0xF8 << ATA_SHIFT_UDMA);
204 if (hpt_dma_blacklisted(adev, "UDMA4", bad_ata66_4))
205 mask &= ~(0xF0 << ATA_SHIFT_UDMA);
206 } else if (adev->class == ATA_DEV_ATAPI)
207 mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
208
209 return mask;
210}
211
212static int hpt36x_cable_detect(struct ata_port *ap)
213{
214 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
215 u8 ata66;
216
217 /*
218 * Each channel of pata_hpt366 occupies separate PCI function
219 * as the primary channel and bit1 indicates the cable type.
220 */
221 pci_read_config_byte(pdev, 0x5A, &ata66);
222 if (ata66 & 2)
223 return ATA_CBL_PATA40;
224 return ATA_CBL_PATA80;
225}
226
227static void hpt366_set_mode(struct ata_port *ap, struct ata_device *adev,
228 u8 mode)
229{
230 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
231 u32 addr = 0x40 + 4 * adev->devno;
232 u32 mask, reg, t;
233
234 /* determine timing mask and find matching clock entry */
235 if (mode < XFER_MW_DMA_0)
236 mask = 0xc1f8ffff;
237 else if (mode < XFER_UDMA_0)
238 mask = 0x303800ff;
239 else
240 mask = 0x30070000;
241
242 t = hpt36x_find_mode(ap, mode);
243
244 /*
245 * Combine new mode bits with old config bits and disable
246 * on-chip PIO FIFO/buffer (and PIO MST mode as well) to avoid
247 * problems handling I/O errors later.
248 */
249 pci_read_config_dword(pdev, addr, ®);
250 reg = ((reg & ~mask) | (t & mask)) & ~0xc0000000;
251 pci_write_config_dword(pdev, addr, reg);
252}
253
254/**
255 * hpt366_set_piomode - PIO setup
256 * @ap: ATA interface
257 * @adev: device on the interface
258 *
259 * Perform PIO mode setup.
260 */
261
262static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
263{
264 hpt366_set_mode(ap, adev, adev->pio_mode);
265}
266
267/**
268 * hpt366_set_dmamode - DMA timing setup
269 * @ap: ATA interface
270 * @adev: Device being configured
271 *
272 * Set up the channel for MWDMA or UDMA modes. Much the same as with
273 * PIO, load the mode number and then set MWDMA or UDMA flag.
274 */
275
276static void hpt366_set_dmamode(struct ata_port *ap, struct ata_device *adev)
277{
278 hpt366_set_mode(ap, adev, adev->dma_mode);
279}
280
281/**
282 * hpt366_prereset - reset the hpt36x bus
283 * @link: ATA link to reset
284 * @deadline: deadline jiffies for the operation
285 *
286 * Perform the initial reset handling for the 36x series controllers.
287 * Reset the hardware and state machine,
288 */
289
290static int hpt366_prereset(struct ata_link *link, unsigned long deadline)
291{
292 struct ata_port *ap = link->ap;
293 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
294 /*
295 * HPT36x chips have one channel per function and have
296 * both channel enable bits located differently and visible
297 * to both functions -- really stupid design decision... :-(
298 * Bit 4 is for the primary channel, bit 5 for the secondary.
299 */
300 static const struct pci_bits hpt366_enable_bits = {
301 0x50, 1, 0x30, 0x30
302 };
303 u8 mcr2;
304
305 if (!pci_test_config_bits(pdev, &hpt366_enable_bits))
306 return -ENOENT;
307
308 pci_read_config_byte(pdev, 0x51, &mcr2);
309 if (mcr2 & 0x80)
310 pci_write_config_byte(pdev, 0x51, mcr2 & ~0x80);
311
312 return ata_sff_prereset(link, deadline);
313}
314
315static const struct scsi_host_template hpt36x_sht = {
316 ATA_BMDMA_SHT(DRV_NAME),
317};
318
319/*
320 * Configuration for HPT366/68
321 */
322
323static struct ata_port_operations hpt366_port_ops = {
324 .inherits = &ata_bmdma_port_ops,
325 .prereset = hpt366_prereset,
326 .cable_detect = hpt36x_cable_detect,
327 .mode_filter = hpt366_filter,
328 .set_piomode = hpt366_set_piomode,
329 .set_dmamode = hpt366_set_dmamode,
330};
331
332/**
333 * hpt36x_init_chipset - common chip setup
334 * @dev: PCI device
335 *
336 * Perform the chip setup work that must be done at both init and
337 * resume time
338 */
339
340static void hpt36x_init_chipset(struct pci_dev *dev)
341{
342 u8 mcr1;
343
344 pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
345 pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
346 pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
347 pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
348
349 /*
350 * Now we'll have to force both channels enabled if at least one
351 * of them has been enabled by BIOS...
352 */
353 pci_read_config_byte(dev, 0x50, &mcr1);
354 if (mcr1 & 0x30)
355 pci_write_config_byte(dev, 0x50, mcr1 | 0x30);
356}
357
358/**
359 * hpt36x_init_one - Initialise an HPT366/368
360 * @dev: PCI device
361 * @id: Entry in match table
362 *
363 * Initialise an HPT36x device. There are some interesting complications
364 * here. Firstly the chip may report 366 and be one of several variants.
365 * Secondly all the timings depend on the clock for the chip which we must
366 * detect and look up
367 *
368 * This is the known chip mappings. It may be missing a couple of later
369 * releases.
370 *
371 * Chip version PCI Rev Notes
372 * HPT366 4 (HPT366) 0 UDMA66
373 * HPT366 4 (HPT366) 1 UDMA66
374 * HPT368 4 (HPT366) 2 UDMA66
375 * HPT37x/30x 4 (HPT366) 3+ Other driver
376 *
377 */
378
379static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
380{
381 static const struct ata_port_info info_hpt366 = {
382 .flags = ATA_FLAG_SLAVE_POSS,
383 .pio_mask = ATA_PIO4,
384 .mwdma_mask = ATA_MWDMA2,
385 .udma_mask = ATA_UDMA4,
386 .port_ops = &hpt366_port_ops
387 };
388 const struct ata_port_info *ppi[] = { &info_hpt366, NULL };
389
390 const void *hpriv = NULL;
391 u32 reg1;
392 int rc;
393
394 rc = pcim_enable_device(dev);
395 if (rc)
396 return rc;
397
398 /* May be a later chip in disguise. Check */
399 /* Newer chips are not in the HPT36x driver. Ignore them */
400 if (dev->revision > 2)
401 return -ENODEV;
402
403 hpt36x_init_chipset(dev);
404
405 pci_read_config_dword(dev, 0x40, ®1);
406
407 /* PCI clocking determines the ATA timing values to use */
408 /* info_hpt366 is safe against re-entry so we can scribble on it */
409 switch ((reg1 & 0xf00) >> 8) {
410 case 9:
411 hpriv = &hpt366_40;
412 break;
413 case 5:
414 hpriv = &hpt366_25;
415 break;
416 default:
417 hpriv = &hpt366_33;
418 break;
419 }
420 /* Now kick off ATA set up */
421 return ata_pci_bmdma_init_one(dev, ppi, &hpt36x_sht, (void *)hpriv, 0);
422}
423
424#ifdef CONFIG_PM_SLEEP
425static int hpt36x_reinit_one(struct pci_dev *dev)
426{
427 struct ata_host *host = pci_get_drvdata(dev);
428 int rc;
429
430 rc = ata_pci_device_do_resume(dev);
431 if (rc)
432 return rc;
433 hpt36x_init_chipset(dev);
434 ata_host_resume(host);
435 return 0;
436}
437#endif
438
439static const struct pci_device_id hpt36x[] = {
440 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
441 { },
442};
443
444static struct pci_driver hpt36x_pci_driver = {
445 .name = DRV_NAME,
446 .id_table = hpt36x,
447 .probe = hpt36x_init_one,
448 .remove = ata_pci_remove_one,
449#ifdef CONFIG_PM_SLEEP
450 .suspend = ata_pci_device_suspend,
451 .resume = hpt36x_reinit_one,
452#endif
453};
454
455module_pci_driver(hpt36x_pci_driver);
456
457MODULE_AUTHOR("Alan Cox");
458MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368");
459MODULE_LICENSE("GPL");
460MODULE_DEVICE_TABLE(pci, hpt36x);
461MODULE_VERSION(DRV_VERSION);
1/*
2 * Libata driver for the highpoint 366 and 368 UDMA66 ATA controllers.
3 *
4 * This driver is heavily based upon:
5 *
6 * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003
7 *
8 * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
9 * Portions Copyright (C) 2001 Sun Microsystems, Inc.
10 * Portions Copyright (C) 2003 Red Hat Inc
11 *
12 *
13 * TODO
14 * Look into engine reset on timeout errors. Should not be required.
15 */
16
17#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
18
19#include <linux/kernel.h>
20#include <linux/module.h>
21#include <linux/pci.h>
22#include <linux/init.h>
23#include <linux/blkdev.h>
24#include <linux/delay.h>
25#include <scsi/scsi_host.h>
26#include <linux/libata.h>
27
28#define DRV_NAME "pata_hpt366"
29#define DRV_VERSION "0.6.11"
30
31struct hpt_clock {
32 u8 xfer_mode;
33 u32 timing;
34};
35
36/* key for bus clock timings
37 * bit
38 * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
39 * cycles = value + 1
40 * 4:7 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
41 * cycles = value + 1
42 * 8:11 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
43 * register access.
44 * 12:15 cmd_low_time. Active time of DIOW_/DIOR_ during task file
45 * register access.
46 * 16:18 udma_cycle_time. Clock cycles for UDMA xfer?
47 * 19:21 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
48 * 22:24 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
49 * register access.
50 * 28 UDMA enable.
51 * 29 DMA enable.
52 * 30 PIO_MST enable. If set, the chip is in bus master mode during
53 * PIO xfer.
54 * 31 FIFO enable.
55 */
56
57static const struct hpt_clock hpt366_40[] = {
58 { XFER_UDMA_4, 0x900fd943 },
59 { XFER_UDMA_3, 0x900ad943 },
60 { XFER_UDMA_2, 0x900bd943 },
61 { XFER_UDMA_1, 0x9008d943 },
62 { XFER_UDMA_0, 0x9008d943 },
63
64 { XFER_MW_DMA_2, 0xa008d943 },
65 { XFER_MW_DMA_1, 0xa010d955 },
66 { XFER_MW_DMA_0, 0xa010d9fc },
67
68 { XFER_PIO_4, 0xc008d963 },
69 { XFER_PIO_3, 0xc010d974 },
70 { XFER_PIO_2, 0xc010d997 },
71 { XFER_PIO_1, 0xc010d9c7 },
72 { XFER_PIO_0, 0xc018d9d9 },
73 { 0, 0x0120d9d9 }
74};
75
76static const struct hpt_clock hpt366_33[] = {
77 { XFER_UDMA_4, 0x90c9a731 },
78 { XFER_UDMA_3, 0x90cfa731 },
79 { XFER_UDMA_2, 0x90caa731 },
80 { XFER_UDMA_1, 0x90cba731 },
81 { XFER_UDMA_0, 0x90c8a731 },
82
83 { XFER_MW_DMA_2, 0xa0c8a731 },
84 { XFER_MW_DMA_1, 0xa0c8a732 }, /* 0xa0c8a733 */
85 { XFER_MW_DMA_0, 0xa0c8a797 },
86
87 { XFER_PIO_4, 0xc0c8a731 },
88 { XFER_PIO_3, 0xc0c8a742 },
89 { XFER_PIO_2, 0xc0d0a753 },
90 { XFER_PIO_1, 0xc0d0a7a3 }, /* 0xc0d0a793 */
91 { XFER_PIO_0, 0xc0d0a7aa }, /* 0xc0d0a7a7 */
92 { 0, 0x0120a7a7 }
93};
94
95static const struct hpt_clock hpt366_25[] = {
96 { XFER_UDMA_4, 0x90c98521 },
97 { XFER_UDMA_3, 0x90cf8521 },
98 { XFER_UDMA_2, 0x90cf8521 },
99 { XFER_UDMA_1, 0x90cb8521 },
100 { XFER_UDMA_0, 0x90cb8521 },
101
102 { XFER_MW_DMA_2, 0xa0ca8521 },
103 { XFER_MW_DMA_1, 0xa0ca8532 },
104 { XFER_MW_DMA_0, 0xa0ca8575 },
105
106 { XFER_PIO_4, 0xc0ca8521 },
107 { XFER_PIO_3, 0xc0ca8532 },
108 { XFER_PIO_2, 0xc0ca8542 },
109 { XFER_PIO_1, 0xc0d08572 },
110 { XFER_PIO_0, 0xc0d08585 },
111 { 0, 0x01208585 }
112};
113
114static const char * const bad_ata33[] = {
115 "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3",
116 "Maxtor 90845U3", "Maxtor 90650U2",
117 "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5",
118 "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
119 "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6",
120 "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
121 "Maxtor 90510D4",
122 "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
123 "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7",
124 "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
125 "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5",
126 "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
127 NULL
128};
129
130static const char * const bad_ata66_4[] = {
131 "IBM-DTLA-307075",
132 "IBM-DTLA-307060",
133 "IBM-DTLA-307045",
134 "IBM-DTLA-307030",
135 "IBM-DTLA-307020",
136 "IBM-DTLA-307015",
137 "IBM-DTLA-305040",
138 "IBM-DTLA-305030",
139 "IBM-DTLA-305020",
140 "IC35L010AVER07-0",
141 "IC35L020AVER07-0",
142 "IC35L030AVER07-0",
143 "IC35L040AVER07-0",
144 "IC35L060AVER07-0",
145 "WDC AC310200R",
146 NULL
147};
148
149static const char * const bad_ata66_3[] = {
150 "WDC AC310200R",
151 NULL
152};
153
154static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr,
155 const char * const list[])
156{
157 unsigned char model_num[ATA_ID_PROD_LEN + 1];
158 int i = 0;
159
160 ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));
161
162 while (list[i] != NULL) {
163 if (!strcmp(list[i], model_num)) {
164 pr_warn("%s is not supported for %s\n",
165 modestr, list[i]);
166 return 1;
167 }
168 i++;
169 }
170 return 0;
171}
172
173/**
174 * hpt366_filter - mode selection filter
175 * @adev: ATA device
176 *
177 * Block UDMA on devices that cause trouble with this controller.
178 */
179
180static unsigned long hpt366_filter(struct ata_device *adev, unsigned long mask)
181{
182 if (adev->class == ATA_DEV_ATA) {
183 if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33))
184 mask &= ~ATA_MASK_UDMA;
185 if (hpt_dma_blacklisted(adev, "UDMA3", bad_ata66_3))
186 mask &= ~(0xF8 << ATA_SHIFT_UDMA);
187 if (hpt_dma_blacklisted(adev, "UDMA4", bad_ata66_4))
188 mask &= ~(0xF0 << ATA_SHIFT_UDMA);
189 } else if (adev->class == ATA_DEV_ATAPI)
190 mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
191
192 return mask;
193}
194
195static int hpt36x_cable_detect(struct ata_port *ap)
196{
197 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
198 u8 ata66;
199
200 /*
201 * Each channel of pata_hpt366 occupies separate PCI function
202 * as the primary channel and bit1 indicates the cable type.
203 */
204 pci_read_config_byte(pdev, 0x5A, &ata66);
205 if (ata66 & 2)
206 return ATA_CBL_PATA40;
207 return ATA_CBL_PATA80;
208}
209
210static void hpt366_set_mode(struct ata_port *ap, struct ata_device *adev,
211 u8 mode)
212{
213 struct hpt_clock *clocks = ap->host->private_data;
214 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
215 u32 addr = 0x40 + 4 * adev->devno;
216 u32 mask, reg;
217
218 /* determine timing mask and find matching clock entry */
219 if (mode < XFER_MW_DMA_0)
220 mask = 0xc1f8ffff;
221 else if (mode < XFER_UDMA_0)
222 mask = 0x303800ff;
223 else
224 mask = 0x30070000;
225
226 while (clocks->xfer_mode) {
227 if (clocks->xfer_mode == mode)
228 break;
229 clocks++;
230 }
231 if (!clocks->xfer_mode)
232 BUG();
233
234 /*
235 * Combine new mode bits with old config bits and disable
236 * on-chip PIO FIFO/buffer (and PIO MST mode as well) to avoid
237 * problems handling I/O errors later.
238 */
239 pci_read_config_dword(pdev, addr, ®);
240 reg = ((reg & ~mask) | (clocks->timing & mask)) & ~0xc0000000;
241 pci_write_config_dword(pdev, addr, reg);
242}
243
244/**
245 * hpt366_set_piomode - PIO setup
246 * @ap: ATA interface
247 * @adev: device on the interface
248 *
249 * Perform PIO mode setup.
250 */
251
252static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
253{
254 hpt366_set_mode(ap, adev, adev->pio_mode);
255}
256
257/**
258 * hpt366_set_dmamode - DMA timing setup
259 * @ap: ATA interface
260 * @adev: Device being configured
261 *
262 * Set up the channel for MWDMA or UDMA modes. Much the same as with
263 * PIO, load the mode number and then set MWDMA or UDMA flag.
264 */
265
266static void hpt366_set_dmamode(struct ata_port *ap, struct ata_device *adev)
267{
268 hpt366_set_mode(ap, adev, adev->dma_mode);
269}
270
271static struct scsi_host_template hpt36x_sht = {
272 ATA_BMDMA_SHT(DRV_NAME),
273};
274
275/*
276 * Configuration for HPT366/68
277 */
278
279static struct ata_port_operations hpt366_port_ops = {
280 .inherits = &ata_bmdma_port_ops,
281 .cable_detect = hpt36x_cable_detect,
282 .mode_filter = hpt366_filter,
283 .set_piomode = hpt366_set_piomode,
284 .set_dmamode = hpt366_set_dmamode,
285};
286
287/**
288 * hpt36x_init_chipset - common chip setup
289 * @dev: PCI device
290 *
291 * Perform the chip setup work that must be done at both init and
292 * resume time
293 */
294
295static void hpt36x_init_chipset(struct pci_dev *dev)
296{
297 u8 drive_fast;
298
299 pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
300 pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
301 pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
302 pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
303
304 pci_read_config_byte(dev, 0x51, &drive_fast);
305 if (drive_fast & 0x80)
306 pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
307}
308
309/**
310 * hpt36x_init_one - Initialise an HPT366/368
311 * @dev: PCI device
312 * @id: Entry in match table
313 *
314 * Initialise an HPT36x device. There are some interesting complications
315 * here. Firstly the chip may report 366 and be one of several variants.
316 * Secondly all the timings depend on the clock for the chip which we must
317 * detect and look up
318 *
319 * This is the known chip mappings. It may be missing a couple of later
320 * releases.
321 *
322 * Chip version PCI Rev Notes
323 * HPT366 4 (HPT366) 0 UDMA66
324 * HPT366 4 (HPT366) 1 UDMA66
325 * HPT368 4 (HPT366) 2 UDMA66
326 * HPT37x/30x 4 (HPT366) 3+ Other driver
327 *
328 */
329
330static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
331{
332 static const struct ata_port_info info_hpt366 = {
333 .flags = ATA_FLAG_SLAVE_POSS,
334 .pio_mask = ATA_PIO4,
335 .mwdma_mask = ATA_MWDMA2,
336 .udma_mask = ATA_UDMA4,
337 .port_ops = &hpt366_port_ops
338 };
339 const struct ata_port_info *ppi[] = { &info_hpt366, NULL };
340
341 void *hpriv = NULL;
342 u32 reg1;
343 int rc;
344
345 rc = pcim_enable_device(dev);
346 if (rc)
347 return rc;
348
349 /* May be a later chip in disguise. Check */
350 /* Newer chips are not in the HPT36x driver. Ignore them */
351 if (dev->revision > 2)
352 return -ENODEV;
353
354 hpt36x_init_chipset(dev);
355
356 pci_read_config_dword(dev, 0x40, ®1);
357
358 /* PCI clocking determines the ATA timing values to use */
359 /* info_hpt366 is safe against re-entry so we can scribble on it */
360 switch ((reg1 & 0x700) >> 8) {
361 case 9:
362 hpriv = &hpt366_40;
363 break;
364 case 5:
365 hpriv = &hpt366_25;
366 break;
367 default:
368 hpriv = &hpt366_33;
369 break;
370 }
371 /* Now kick off ATA set up */
372 return ata_pci_bmdma_init_one(dev, ppi, &hpt36x_sht, hpriv, 0);
373}
374
375#ifdef CONFIG_PM
376static int hpt36x_reinit_one(struct pci_dev *dev)
377{
378 struct ata_host *host = dev_get_drvdata(&dev->dev);
379 int rc;
380
381 rc = ata_pci_device_do_resume(dev);
382 if (rc)
383 return rc;
384 hpt36x_init_chipset(dev);
385 ata_host_resume(host);
386 return 0;
387}
388#endif
389
390static const struct pci_device_id hpt36x[] = {
391 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
392 { },
393};
394
395static struct pci_driver hpt36x_pci_driver = {
396 .name = DRV_NAME,
397 .id_table = hpt36x,
398 .probe = hpt36x_init_one,
399 .remove = ata_pci_remove_one,
400#ifdef CONFIG_PM
401 .suspend = ata_pci_device_suspend,
402 .resume = hpt36x_reinit_one,
403#endif
404};
405
406static int __init hpt36x_init(void)
407{
408 return pci_register_driver(&hpt36x_pci_driver);
409}
410
411static void __exit hpt36x_exit(void)
412{
413 pci_unregister_driver(&hpt36x_pci_driver);
414}
415
416MODULE_AUTHOR("Alan Cox");
417MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368");
418MODULE_LICENSE("GPL");
419MODULE_DEVICE_TABLE(pci, hpt36x);
420MODULE_VERSION(DRV_VERSION);
421
422module_init(hpt36x_init);
423module_exit(hpt36x_exit);