Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Raydium touchscreen I2C driver.
4 *
5 * Copyright (C) 2012-2014, Raydium Semiconductor Corporation.
6 *
7 * Raydium reserves the right to make changes without further notice
8 * to the materials described herein. Raydium does not assume any
9 * liability arising out of the application described herein.
10 *
11 * Contact Raydium Semiconductor Corporation at www.rad-ic.com
12 */
13
14#include <linux/acpi.h>
15#include <linux/delay.h>
16#include <linux/firmware.h>
17#include <linux/gpio/consumer.h>
18#include <linux/i2c.h>
19#include <linux/input.h>
20#include <linux/input/mt.h>
21#include <linux/interrupt.h>
22#include <linux/module.h>
23#include <linux/of.h>
24#include <linux/pm_wakeirq.h>
25#include <linux/regulator/consumer.h>
26#include <linux/slab.h>
27#include <asm/unaligned.h>
28
29/* Slave I2C mode */
30#define RM_BOOT_BLDR 0x02
31#define RM_BOOT_MAIN 0x03
32
33/* I2C bootoloader commands */
34#define RM_CMD_BOOT_PAGE_WRT 0x0B /* send bl page write */
35#define RM_CMD_BOOT_WRT 0x11 /* send bl write */
36#define RM_CMD_BOOT_ACK 0x22 /* send ack*/
37#define RM_CMD_BOOT_CHK 0x33 /* send data check */
38#define RM_CMD_BOOT_READ 0x44 /* send wait bl data ready*/
39
40#define RM_BOOT_RDY 0xFF /* bl data ready */
41#define RM_BOOT_CMD_READHWID 0x0E /* read hwid */
42
43/* I2C main commands */
44#define RM_CMD_QUERY_BANK 0x2B
45#define RM_CMD_DATA_BANK 0x4D
46#define RM_CMD_ENTER_SLEEP 0x4E
47#define RM_CMD_BANK_SWITCH 0xAA
48
49#define RM_RESET_MSG_ADDR 0x40000004
50
51#define RM_MAX_READ_SIZE 56
52#define RM_PACKET_CRC_SIZE 2
53
54/* Touch relative info */
55#define RM_MAX_RETRIES 3
56#define RM_RETRY_DELAY_MS 20
57#define RM_MAX_TOUCH_NUM 10
58#define RM_BOOT_DELAY_MS 100
59
60/* Offsets in contact data */
61#define RM_CONTACT_STATE_POS 0
62#define RM_CONTACT_X_POS 1
63#define RM_CONTACT_Y_POS 3
64#define RM_CONTACT_PRESSURE_POS 5
65#define RM_CONTACT_WIDTH_X_POS 6
66#define RM_CONTACT_WIDTH_Y_POS 7
67
68/* Bootloader relative info */
69#define RM_BL_WRT_CMD_SIZE 3 /* bl flash wrt cmd size */
70#define RM_BL_WRT_PKG_SIZE 32 /* bl wrt pkg size */
71#define RM_BL_WRT_LEN (RM_BL_WRT_PKG_SIZE + RM_BL_WRT_CMD_SIZE)
72#define RM_FW_PAGE_SIZE 128
73#define RM_MAX_FW_RETRIES 30
74#define RM_MAX_FW_SIZE 0xD000
75
76#define RM_POWERON_DELAY_USEC 500
77#define RM_RESET_DELAY_MSEC 50
78
79enum raydium_bl_cmd {
80 BL_HEADER = 0,
81 BL_PAGE_STR,
82 BL_PKG_IDX,
83 BL_DATA_STR,
84};
85
86enum raydium_bl_ack {
87 RAYDIUM_ACK_NULL = 0,
88 RAYDIUM_WAIT_READY,
89 RAYDIUM_PATH_READY,
90};
91
92enum raydium_boot_mode {
93 RAYDIUM_TS_MAIN = 0,
94 RAYDIUM_TS_BLDR,
95};
96
97/* Response to RM_CMD_DATA_BANK request */
98struct raydium_data_info {
99 __le32 data_bank_addr;
100 u8 pkg_size;
101 u8 tp_info_size;
102};
103
104struct raydium_info {
105 __le32 hw_ver; /*device version */
106 u8 main_ver;
107 u8 sub_ver;
108 __le16 ft_ver; /* test version */
109 u8 x_num;
110 u8 y_num;
111 __le16 x_max;
112 __le16 y_max;
113 u8 x_res; /* units/mm */
114 u8 y_res; /* units/mm */
115};
116
117/* struct raydium_data - represents state of Raydium touchscreen device */
118struct raydium_data {
119 struct i2c_client *client;
120 struct input_dev *input;
121
122 struct regulator *avdd;
123 struct regulator *vccio;
124 struct gpio_desc *reset_gpio;
125
126 struct raydium_info info;
127
128 struct mutex sysfs_mutex;
129
130 u8 *report_data;
131
132 u32 data_bank_addr;
133 u8 report_size;
134 u8 contact_size;
135 u8 pkg_size;
136
137 enum raydium_boot_mode boot_mode;
138};
139
140/*
141 * Header to be sent for RM_CMD_BANK_SWITCH command. This is used by
142 * raydium_i2c_{read|send} below.
143 */
144struct __packed raydium_bank_switch_header {
145 u8 cmd;
146 __be32 be_addr;
147};
148
149static int raydium_i2c_xfer(struct i2c_client *client, u32 addr,
150 struct i2c_msg *xfer, size_t xfer_count)
151{
152 int ret;
153 /*
154 * If address is greater than 255, then RM_CMD_BANK_SWITCH needs to be
155 * sent first. Else, skip the header i.e. xfer[0].
156 */
157 int xfer_start_idx = (addr > 0xff) ? 0 : 1;
158 xfer_count -= xfer_start_idx;
159
160 ret = i2c_transfer(client->adapter, &xfer[xfer_start_idx], xfer_count);
161 if (likely(ret == xfer_count))
162 return 0;
163
164 return ret < 0 ? ret : -EIO;
165}
166
167static int raydium_i2c_send(struct i2c_client *client,
168 u32 addr, const void *data, size_t len)
169{
170 int tries = 0;
171 int error;
172 u8 *tx_buf;
173 u8 reg_addr = addr & 0xff;
174
175 tx_buf = kmalloc(len + 1, GFP_KERNEL);
176 if (!tx_buf)
177 return -ENOMEM;
178
179 tx_buf[0] = reg_addr;
180 memcpy(tx_buf + 1, data, len);
181
182 do {
183 struct raydium_bank_switch_header header = {
184 .cmd = RM_CMD_BANK_SWITCH,
185 .be_addr = cpu_to_be32(addr),
186 };
187
188 /*
189 * Perform as a single i2c_transfer transaction to ensure that
190 * no other I2C transactions are initiated on the bus to any
191 * other device in between. Initiating transacations to other
192 * devices after RM_CMD_BANK_SWITCH is sent is known to cause
193 * issues. This is also why regmap infrastructure cannot be used
194 * for this driver. Regmap handles page(bank) switch and reads
195 * as separate i2c_transfer() operations. This can result in
196 * problems if the Raydium device is on a shared I2C bus.
197 */
198 struct i2c_msg xfer[] = {
199 {
200 .addr = client->addr,
201 .len = sizeof(header),
202 .buf = (u8 *)&header,
203 },
204 {
205 .addr = client->addr,
206 .len = len + 1,
207 .buf = tx_buf,
208 },
209 };
210
211 error = raydium_i2c_xfer(client, addr, xfer, ARRAY_SIZE(xfer));
212 if (likely(!error))
213 goto out;
214
215 msleep(RM_RETRY_DELAY_MS);
216 } while (++tries < RM_MAX_RETRIES);
217
218 dev_err(&client->dev, "%s failed: %d\n", __func__, error);
219out:
220 kfree(tx_buf);
221 return error;
222}
223
224static int raydium_i2c_read(struct i2c_client *client,
225 u32 addr, void *data, size_t len)
226{
227 int error;
228
229 while (len) {
230 u8 reg_addr = addr & 0xff;
231 struct raydium_bank_switch_header header = {
232 .cmd = RM_CMD_BANK_SWITCH,
233 .be_addr = cpu_to_be32(addr),
234 };
235 size_t xfer_len = min_t(size_t, len, RM_MAX_READ_SIZE);
236
237 /*
238 * Perform as a single i2c_transfer transaction to ensure that
239 * no other I2C transactions are initiated on the bus to any
240 * other device in between. Initiating transacations to other
241 * devices after RM_CMD_BANK_SWITCH is sent is known to cause
242 * issues. This is also why regmap infrastructure cannot be used
243 * for this driver. Regmap handles page(bank) switch and writes
244 * as separate i2c_transfer() operations. This can result in
245 * problems if the Raydium device is on a shared I2C bus.
246 */
247 struct i2c_msg xfer[] = {
248 {
249 .addr = client->addr,
250 .len = sizeof(header),
251 .buf = (u8 *)&header,
252 },
253 {
254 .addr = client->addr,
255 .len = 1,
256 .buf = ®_addr,
257 },
258 {
259 .addr = client->addr,
260 .len = xfer_len,
261 .buf = data,
262 .flags = I2C_M_RD,
263 }
264 };
265
266 error = raydium_i2c_xfer(client, addr, xfer, ARRAY_SIZE(xfer));
267 if (unlikely(error))
268 return error;
269
270 len -= xfer_len;
271 data += xfer_len;
272 addr += xfer_len;
273 }
274
275 return 0;
276}
277
278static int raydium_i2c_sw_reset(struct i2c_client *client)
279{
280 const u8 soft_rst_cmd = 0x01;
281 int error;
282
283 error = raydium_i2c_send(client, RM_RESET_MSG_ADDR, &soft_rst_cmd,
284 sizeof(soft_rst_cmd));
285 if (error) {
286 dev_err(&client->dev, "software reset failed: %d\n", error);
287 return error;
288 }
289
290 msleep(RM_RESET_DELAY_MSEC);
291
292 return 0;
293}
294
295static int raydium_i2c_query_ts_bootloader_info(struct raydium_data *ts)
296{
297 struct i2c_client *client = ts->client;
298 static const u8 get_hwid[] = { RM_BOOT_CMD_READHWID,
299 0x10, 0xc0, 0x01, 0x00, 0x04, 0x00 };
300 u8 rbuf[5] = { 0 };
301 u32 hw_ver;
302 int error;
303
304 error = raydium_i2c_send(client, RM_CMD_BOOT_WRT,
305 get_hwid, sizeof(get_hwid));
306 if (error) {
307 dev_err(&client->dev, "WRT HWID command failed: %d\n", error);
308 return error;
309 }
310
311 error = raydium_i2c_send(client, RM_CMD_BOOT_ACK, rbuf, 1);
312 if (error) {
313 dev_err(&client->dev, "Ack HWID command failed: %d\n", error);
314 return error;
315 }
316
317 error = raydium_i2c_read(client, RM_CMD_BOOT_CHK, rbuf, sizeof(rbuf));
318 if (error) {
319 dev_err(&client->dev, "Read HWID command failed: %d (%4ph)\n",
320 error, rbuf + 1);
321 hw_ver = 0xffffffffUL;
322 } else {
323 hw_ver = get_unaligned_be32(rbuf + 1);
324 }
325
326 ts->info.hw_ver = cpu_to_le32(hw_ver);
327 ts->info.main_ver = 0xff;
328 ts->info.sub_ver = 0xff;
329
330 return error;
331}
332
333static int raydium_i2c_query_ts_info(struct raydium_data *ts)
334{
335 struct i2c_client *client = ts->client;
336 struct raydium_data_info data_info;
337 __le32 query_bank_addr;
338
339 int error, retry_cnt;
340
341 for (retry_cnt = 0; retry_cnt < RM_MAX_RETRIES; retry_cnt++) {
342 error = raydium_i2c_read(client, RM_CMD_DATA_BANK,
343 &data_info, sizeof(data_info));
344 if (error)
345 continue;
346
347 /*
348 * Warn user if we already allocated memory for reports and
349 * then the size changed (due to firmware update?) and keep
350 * old size instead.
351 */
352 if (ts->report_data && ts->pkg_size != data_info.pkg_size) {
353 dev_warn(&client->dev,
354 "report size changes, was: %d, new: %d\n",
355 ts->pkg_size, data_info.pkg_size);
356 } else {
357 ts->pkg_size = data_info.pkg_size;
358 ts->report_size = ts->pkg_size - RM_PACKET_CRC_SIZE;
359 }
360
361 ts->contact_size = data_info.tp_info_size;
362 ts->data_bank_addr = le32_to_cpu(data_info.data_bank_addr);
363
364 dev_dbg(&client->dev,
365 "data_bank_addr: %#08x, report_size: %d, contact_size: %d\n",
366 ts->data_bank_addr, ts->report_size, ts->contact_size);
367
368 error = raydium_i2c_read(client, RM_CMD_QUERY_BANK,
369 &query_bank_addr,
370 sizeof(query_bank_addr));
371 if (error)
372 continue;
373
374 error = raydium_i2c_read(client, le32_to_cpu(query_bank_addr),
375 &ts->info, sizeof(ts->info));
376 if (error)
377 continue;
378
379 return 0;
380 }
381
382 dev_err(&client->dev, "failed to query device parameters: %d\n", error);
383 return error;
384}
385
386static int raydium_i2c_check_fw_status(struct raydium_data *ts)
387{
388 struct i2c_client *client = ts->client;
389 static const u8 bl_ack = 0x62;
390 static const u8 main_ack = 0x66;
391 u8 buf[4];
392 int error;
393
394 error = raydium_i2c_read(client, RM_CMD_BOOT_READ, buf, sizeof(buf));
395 if (!error) {
396 if (buf[0] == bl_ack)
397 ts->boot_mode = RAYDIUM_TS_BLDR;
398 else if (buf[0] == main_ack)
399 ts->boot_mode = RAYDIUM_TS_MAIN;
400 return 0;
401 }
402
403 return error;
404}
405
406static int raydium_i2c_initialize(struct raydium_data *ts)
407{
408 struct i2c_client *client = ts->client;
409 int error, retry_cnt;
410
411 for (retry_cnt = 0; retry_cnt < RM_MAX_RETRIES; retry_cnt++) {
412 /* Wait for Hello packet */
413 msleep(RM_BOOT_DELAY_MS);
414
415 error = raydium_i2c_check_fw_status(ts);
416 if (error) {
417 dev_err(&client->dev,
418 "failed to read 'hello' packet: %d\n", error);
419 continue;
420 }
421
422 if (ts->boot_mode == RAYDIUM_TS_BLDR ||
423 ts->boot_mode == RAYDIUM_TS_MAIN) {
424 break;
425 }
426 }
427
428 if (error)
429 ts->boot_mode = RAYDIUM_TS_BLDR;
430
431 if (ts->boot_mode == RAYDIUM_TS_BLDR)
432 raydium_i2c_query_ts_bootloader_info(ts);
433 else
434 raydium_i2c_query_ts_info(ts);
435
436 return error;
437}
438
439static int raydium_i2c_bl_chk_state(struct i2c_client *client,
440 enum raydium_bl_ack state)
441{
442 static const u8 ack_ok[] = { 0xFF, 0x39, 0x30, 0x30, 0x54 };
443 u8 rbuf[sizeof(ack_ok)];
444 u8 retry;
445 int error;
446
447 for (retry = 0; retry < RM_MAX_FW_RETRIES; retry++) {
448 switch (state) {
449 case RAYDIUM_ACK_NULL:
450 return 0;
451
452 case RAYDIUM_WAIT_READY:
453 error = raydium_i2c_read(client, RM_CMD_BOOT_CHK,
454 &rbuf[0], 1);
455 if (!error && rbuf[0] == RM_BOOT_RDY)
456 return 0;
457
458 break;
459
460 case RAYDIUM_PATH_READY:
461 error = raydium_i2c_read(client, RM_CMD_BOOT_CHK,
462 rbuf, sizeof(rbuf));
463 if (!error && !memcmp(rbuf, ack_ok, sizeof(ack_ok)))
464 return 0;
465
466 break;
467
468 default:
469 dev_err(&client->dev, "%s: invalid target state %d\n",
470 __func__, state);
471 return -EINVAL;
472 }
473
474 msleep(20);
475 }
476
477 return -ETIMEDOUT;
478}
479
480static int raydium_i2c_write_object(struct i2c_client *client,
481 const void *data, size_t len,
482 enum raydium_bl_ack state)
483{
484 int error;
485 static const u8 cmd[] = { 0xFF, 0x39 };
486
487 error = raydium_i2c_send(client, RM_CMD_BOOT_WRT, data, len);
488 if (error) {
489 dev_err(&client->dev, "WRT obj command failed: %d\n",
490 error);
491 return error;
492 }
493
494 error = raydium_i2c_send(client, RM_CMD_BOOT_ACK, cmd, sizeof(cmd));
495 if (error) {
496 dev_err(&client->dev, "Ack obj command failed: %d\n", error);
497 return error;
498 }
499
500 error = raydium_i2c_bl_chk_state(client, state);
501 if (error) {
502 dev_err(&client->dev, "BL check state failed: %d\n", error);
503 return error;
504 }
505 return 0;
506}
507
508static int raydium_i2c_boot_trigger(struct i2c_client *client)
509{
510 static const u8 cmd[7][6] = {
511 { 0x08, 0x0C, 0x09, 0x00, 0x50, 0xD7 },
512 { 0x08, 0x04, 0x09, 0x00, 0x50, 0xA5 },
513 { 0x08, 0x04, 0x09, 0x00, 0x50, 0x00 },
514 { 0x08, 0x04, 0x09, 0x00, 0x50, 0xA5 },
515 { 0x08, 0x0C, 0x09, 0x00, 0x50, 0x00 },
516 { 0x06, 0x01, 0x00, 0x00, 0x00, 0x00 },
517 { 0x02, 0xA2, 0x00, 0x00, 0x00, 0x00 },
518 };
519 int i;
520 int error;
521
522 for (i = 0; i < 7; i++) {
523 error = raydium_i2c_write_object(client, cmd[i], sizeof(cmd[i]),
524 RAYDIUM_WAIT_READY);
525 if (error) {
526 dev_err(&client->dev,
527 "boot trigger failed at step %d: %d\n",
528 i, error);
529 return error;
530 }
531 }
532
533 return 0;
534}
535
536static int raydium_i2c_fw_trigger(struct i2c_client *client)
537{
538 static const u8 cmd[5][11] = {
539 { 0, 0x09, 0x71, 0x0C, 0x09, 0x00, 0x50, 0xD7, 0, 0, 0 },
540 { 0, 0x09, 0x71, 0x04, 0x09, 0x00, 0x50, 0xA5, 0, 0, 0 },
541 { 0, 0x09, 0x71, 0x04, 0x09, 0x00, 0x50, 0x00, 0, 0, 0 },
542 { 0, 0x09, 0x71, 0x04, 0x09, 0x00, 0x50, 0xA5, 0, 0, 0 },
543 { 0, 0x09, 0x71, 0x0C, 0x09, 0x00, 0x50, 0x00, 0, 0, 0 },
544 };
545 int i;
546 int error;
547
548 for (i = 0; i < 5; i++) {
549 error = raydium_i2c_write_object(client, cmd[i], sizeof(cmd[i]),
550 RAYDIUM_ACK_NULL);
551 if (error) {
552 dev_err(&client->dev,
553 "fw trigger failed at step %d: %d\n",
554 i, error);
555 return error;
556 }
557 }
558
559 return 0;
560}
561
562static int raydium_i2c_check_path(struct i2c_client *client)
563{
564 static const u8 cmd[] = { 0x09, 0x00, 0x09, 0x00, 0x50, 0x10, 0x00 };
565 int error;
566
567 error = raydium_i2c_write_object(client, cmd, sizeof(cmd),
568 RAYDIUM_PATH_READY);
569 if (error) {
570 dev_err(&client->dev, "check path command failed: %d\n", error);
571 return error;
572 }
573
574 return 0;
575}
576
577static int raydium_i2c_enter_bl(struct i2c_client *client)
578{
579 static const u8 cal_cmd[] = { 0x00, 0x01, 0x52 };
580 int error;
581
582 error = raydium_i2c_write_object(client, cal_cmd, sizeof(cal_cmd),
583 RAYDIUM_ACK_NULL);
584 if (error) {
585 dev_err(&client->dev, "enter bl command failed: %d\n", error);
586 return error;
587 }
588
589 msleep(RM_BOOT_DELAY_MS);
590 return 0;
591}
592
593static int raydium_i2c_leave_bl(struct i2c_client *client)
594{
595 static const u8 leave_cmd[] = { 0x05, 0x00 };
596 int error;
597
598 error = raydium_i2c_write_object(client, leave_cmd, sizeof(leave_cmd),
599 RAYDIUM_ACK_NULL);
600 if (error) {
601 dev_err(&client->dev, "leave bl command failed: %d\n", error);
602 return error;
603 }
604
605 msleep(RM_BOOT_DELAY_MS);
606 return 0;
607}
608
609static int raydium_i2c_write_checksum(struct i2c_client *client,
610 size_t length, u16 checksum)
611{
612 u8 checksum_cmd[] = { 0x00, 0x05, 0x6D, 0x00, 0x00, 0x00, 0x00 };
613 int error;
614
615 put_unaligned_le16(length, &checksum_cmd[3]);
616 put_unaligned_le16(checksum, &checksum_cmd[5]);
617
618 error = raydium_i2c_write_object(client,
619 checksum_cmd, sizeof(checksum_cmd),
620 RAYDIUM_ACK_NULL);
621 if (error) {
622 dev_err(&client->dev, "failed to write checksum: %d\n",
623 error);
624 return error;
625 }
626
627 return 0;
628}
629
630static int raydium_i2c_disable_watch_dog(struct i2c_client *client)
631{
632 static const u8 cmd[] = { 0x0A, 0xAA };
633 int error;
634
635 error = raydium_i2c_write_object(client, cmd, sizeof(cmd),
636 RAYDIUM_WAIT_READY);
637 if (error) {
638 dev_err(&client->dev, "disable watchdog command failed: %d\n",
639 error);
640 return error;
641 }
642
643 return 0;
644}
645
646static int raydium_i2c_fw_write_page(struct i2c_client *client,
647 u16 page_idx, const void *data, size_t len)
648{
649 u8 buf[RM_BL_WRT_LEN];
650 size_t xfer_len;
651 int error;
652 int i;
653
654 BUILD_BUG_ON((RM_FW_PAGE_SIZE % RM_BL_WRT_PKG_SIZE) != 0);
655
656 for (i = 0; i < RM_FW_PAGE_SIZE / RM_BL_WRT_PKG_SIZE; i++) {
657 buf[BL_HEADER] = RM_CMD_BOOT_PAGE_WRT;
658 buf[BL_PAGE_STR] = page_idx ? 0xff : 0;
659 buf[BL_PKG_IDX] = i + 1;
660
661 xfer_len = min_t(size_t, len, RM_BL_WRT_PKG_SIZE);
662 memcpy(&buf[BL_DATA_STR], data, xfer_len);
663 if (len < RM_BL_WRT_PKG_SIZE)
664 memset(&buf[BL_DATA_STR + xfer_len], 0xff,
665 RM_BL_WRT_PKG_SIZE - xfer_len);
666
667 error = raydium_i2c_write_object(client, buf, RM_BL_WRT_LEN,
668 RAYDIUM_WAIT_READY);
669 if (error) {
670 dev_err(&client->dev,
671 "page write command failed for page %d, chunk %d: %d\n",
672 page_idx, i, error);
673 return error;
674 }
675
676 data += xfer_len;
677 len -= xfer_len;
678 }
679
680 return error;
681}
682
683static u16 raydium_calc_chksum(const u8 *buf, u16 len)
684{
685 u16 checksum = 0;
686 u16 i;
687
688 for (i = 0; i < len; i++)
689 checksum += buf[i];
690
691 return checksum;
692}
693
694static int raydium_i2c_do_update_firmware(struct raydium_data *ts,
695 const struct firmware *fw)
696{
697 struct i2c_client *client = ts->client;
698 const void *data;
699 size_t data_len;
700 size_t len;
701 int page_nr;
702 int i;
703 int error;
704 u16 fw_checksum;
705
706 if (fw->size == 0 || fw->size > RM_MAX_FW_SIZE) {
707 dev_err(&client->dev, "Invalid firmware length\n");
708 return -EINVAL;
709 }
710
711 error = raydium_i2c_check_fw_status(ts);
712 if (error) {
713 dev_err(&client->dev, "Unable to access IC %d\n", error);
714 return error;
715 }
716
717 if (ts->boot_mode == RAYDIUM_TS_MAIN) {
718 for (i = 0; i < RM_MAX_RETRIES; i++) {
719 error = raydium_i2c_enter_bl(client);
720 if (!error) {
721 error = raydium_i2c_check_fw_status(ts);
722 if (error) {
723 dev_err(&client->dev,
724 "unable to access IC: %d\n",
725 error);
726 return error;
727 }
728
729 if (ts->boot_mode == RAYDIUM_TS_BLDR)
730 break;
731 }
732 }
733
734 if (ts->boot_mode == RAYDIUM_TS_MAIN) {
735 dev_err(&client->dev,
736 "failed to jump to boot loader: %d\n",
737 error);
738 return -EIO;
739 }
740 }
741
742 error = raydium_i2c_disable_watch_dog(client);
743 if (error)
744 return error;
745
746 error = raydium_i2c_check_path(client);
747 if (error)
748 return error;
749
750 error = raydium_i2c_boot_trigger(client);
751 if (error) {
752 dev_err(&client->dev, "send boot trigger fail: %d\n", error);
753 return error;
754 }
755
756 msleep(RM_BOOT_DELAY_MS);
757
758 data = fw->data;
759 data_len = fw->size;
760 page_nr = 0;
761
762 while (data_len) {
763 len = min_t(size_t, data_len, RM_FW_PAGE_SIZE);
764
765 error = raydium_i2c_fw_write_page(client, page_nr++, data, len);
766 if (error)
767 return error;
768
769 msleep(20);
770
771 data += len;
772 data_len -= len;
773 }
774
775 error = raydium_i2c_leave_bl(client);
776 if (error) {
777 dev_err(&client->dev,
778 "failed to leave boot loader: %d\n", error);
779 return error;
780 }
781
782 dev_dbg(&client->dev, "left boot loader mode\n");
783 msleep(RM_BOOT_DELAY_MS);
784
785 error = raydium_i2c_check_fw_status(ts);
786 if (error) {
787 dev_err(&client->dev,
788 "failed to check fw status after write: %d\n",
789 error);
790 return error;
791 }
792
793 if (ts->boot_mode != RAYDIUM_TS_MAIN) {
794 dev_err(&client->dev,
795 "failed to switch to main fw after writing firmware: %d\n",
796 error);
797 return -EINVAL;
798 }
799
800 error = raydium_i2c_fw_trigger(client);
801 if (error) {
802 dev_err(&client->dev, "failed to trigger fw: %d\n", error);
803 return error;
804 }
805
806 fw_checksum = raydium_calc_chksum(fw->data, fw->size);
807
808 error = raydium_i2c_write_checksum(client, fw->size, fw_checksum);
809 if (error)
810 return error;
811
812 return 0;
813}
814
815static int raydium_i2c_fw_update(struct raydium_data *ts)
816{
817 struct i2c_client *client = ts->client;
818 const struct firmware *fw = NULL;
819 char *fw_file;
820 int error;
821
822 fw_file = kasprintf(GFP_KERNEL, "raydium_%#04x.fw",
823 le32_to_cpu(ts->info.hw_ver));
824 if (!fw_file)
825 return -ENOMEM;
826
827 dev_dbg(&client->dev, "firmware name: %s\n", fw_file);
828
829 error = request_firmware(&fw, fw_file, &client->dev);
830 if (error) {
831 dev_err(&client->dev, "Unable to open firmware %s\n", fw_file);
832 goto out_free_fw_file;
833 }
834
835 disable_irq(client->irq);
836
837 error = raydium_i2c_do_update_firmware(ts, fw);
838 if (error) {
839 dev_err(&client->dev, "firmware update failed: %d\n", error);
840 ts->boot_mode = RAYDIUM_TS_BLDR;
841 goto out_enable_irq;
842 }
843
844 error = raydium_i2c_initialize(ts);
845 if (error) {
846 dev_err(&client->dev,
847 "failed to initialize device after firmware update: %d\n",
848 error);
849 ts->boot_mode = RAYDIUM_TS_BLDR;
850 goto out_enable_irq;
851 }
852
853 ts->boot_mode = RAYDIUM_TS_MAIN;
854
855out_enable_irq:
856 enable_irq(client->irq);
857 msleep(100);
858
859 release_firmware(fw);
860
861out_free_fw_file:
862 kfree(fw_file);
863
864 return error;
865}
866
867static void raydium_mt_event(struct raydium_data *ts)
868{
869 int i;
870
871 for (i = 0; i < ts->report_size / ts->contact_size; i++) {
872 u8 *contact = &ts->report_data[ts->contact_size * i];
873 bool state = contact[RM_CONTACT_STATE_POS];
874 u8 wx, wy;
875
876 input_mt_slot(ts->input, i);
877 input_mt_report_slot_state(ts->input, MT_TOOL_FINGER, state);
878
879 if (!state)
880 continue;
881
882 input_report_abs(ts->input, ABS_MT_POSITION_X,
883 get_unaligned_le16(&contact[RM_CONTACT_X_POS]));
884 input_report_abs(ts->input, ABS_MT_POSITION_Y,
885 get_unaligned_le16(&contact[RM_CONTACT_Y_POS]));
886 input_report_abs(ts->input, ABS_MT_PRESSURE,
887 contact[RM_CONTACT_PRESSURE_POS]);
888
889 wx = contact[RM_CONTACT_WIDTH_X_POS];
890 wy = contact[RM_CONTACT_WIDTH_Y_POS];
891
892 input_report_abs(ts->input, ABS_MT_TOUCH_MAJOR, max(wx, wy));
893 input_report_abs(ts->input, ABS_MT_TOUCH_MINOR, min(wx, wy));
894 }
895
896 input_mt_sync_frame(ts->input);
897 input_sync(ts->input);
898}
899
900static irqreturn_t raydium_i2c_irq(int irq, void *_dev)
901{
902 struct raydium_data *ts = _dev;
903 int error;
904 u16 fw_crc;
905 u16 calc_crc;
906
907 if (ts->boot_mode != RAYDIUM_TS_MAIN)
908 goto out;
909
910 error = raydium_i2c_read(ts->client, ts->data_bank_addr,
911 ts->report_data, ts->pkg_size);
912 if (error)
913 goto out;
914
915 fw_crc = get_unaligned_le16(&ts->report_data[ts->report_size]);
916 calc_crc = raydium_calc_chksum(ts->report_data, ts->report_size);
917 if (unlikely(fw_crc != calc_crc)) {
918 dev_warn(&ts->client->dev,
919 "%s: invalid packet crc %#04x vs %#04x\n",
920 __func__, calc_crc, fw_crc);
921 goto out;
922 }
923
924 raydium_mt_event(ts);
925
926out:
927 return IRQ_HANDLED;
928}
929
930static ssize_t raydium_i2c_fw_ver_show(struct device *dev,
931 struct device_attribute *attr, char *buf)
932{
933 struct i2c_client *client = to_i2c_client(dev);
934 struct raydium_data *ts = i2c_get_clientdata(client);
935
936 return sprintf(buf, "%d.%d\n", ts->info.main_ver, ts->info.sub_ver);
937}
938
939static ssize_t raydium_i2c_hw_ver_show(struct device *dev,
940 struct device_attribute *attr, char *buf)
941{
942 struct i2c_client *client = to_i2c_client(dev);
943 struct raydium_data *ts = i2c_get_clientdata(client);
944
945 return sprintf(buf, "%#04x\n", le32_to_cpu(ts->info.hw_ver));
946}
947
948static ssize_t raydium_i2c_boot_mode_show(struct device *dev,
949 struct device_attribute *attr,
950 char *buf)
951{
952 struct i2c_client *client = to_i2c_client(dev);
953 struct raydium_data *ts = i2c_get_clientdata(client);
954
955 return sprintf(buf, "%s\n",
956 ts->boot_mode == RAYDIUM_TS_MAIN ?
957 "Normal" : "Recovery");
958}
959
960static ssize_t raydium_i2c_update_fw_store(struct device *dev,
961 struct device_attribute *attr,
962 const char *buf, size_t count)
963{
964 struct i2c_client *client = to_i2c_client(dev);
965 struct raydium_data *ts = i2c_get_clientdata(client);
966 int error;
967
968 error = mutex_lock_interruptible(&ts->sysfs_mutex);
969 if (error)
970 return error;
971
972 error = raydium_i2c_fw_update(ts);
973
974 mutex_unlock(&ts->sysfs_mutex);
975
976 return error ?: count;
977}
978
979static ssize_t raydium_i2c_calibrate_store(struct device *dev,
980 struct device_attribute *attr,
981 const char *buf, size_t count)
982{
983 struct i2c_client *client = to_i2c_client(dev);
984 struct raydium_data *ts = i2c_get_clientdata(client);
985 static const u8 cal_cmd[] = { 0x00, 0x01, 0x9E };
986 int error;
987
988 error = mutex_lock_interruptible(&ts->sysfs_mutex);
989 if (error)
990 return error;
991
992 error = raydium_i2c_write_object(client, cal_cmd, sizeof(cal_cmd),
993 RAYDIUM_WAIT_READY);
994 if (error)
995 dev_err(&client->dev, "calibrate command failed: %d\n", error);
996
997 mutex_unlock(&ts->sysfs_mutex);
998 return error ?: count;
999}
1000
1001static DEVICE_ATTR(fw_version, S_IRUGO, raydium_i2c_fw_ver_show, NULL);
1002static DEVICE_ATTR(hw_version, S_IRUGO, raydium_i2c_hw_ver_show, NULL);
1003static DEVICE_ATTR(boot_mode, S_IRUGO, raydium_i2c_boot_mode_show, NULL);
1004static DEVICE_ATTR(update_fw, S_IWUSR, NULL, raydium_i2c_update_fw_store);
1005static DEVICE_ATTR(calibrate, S_IWUSR, NULL, raydium_i2c_calibrate_store);
1006
1007static struct attribute *raydium_i2c_attributes[] = {
1008 &dev_attr_update_fw.attr,
1009 &dev_attr_boot_mode.attr,
1010 &dev_attr_fw_version.attr,
1011 &dev_attr_hw_version.attr,
1012 &dev_attr_calibrate.attr,
1013 NULL
1014};
1015
1016static const struct attribute_group raydium_i2c_attribute_group = {
1017 .attrs = raydium_i2c_attributes,
1018};
1019
1020static int raydium_i2c_power_on(struct raydium_data *ts)
1021{
1022 int error;
1023
1024 if (!ts->reset_gpio)
1025 return 0;
1026
1027 gpiod_set_value_cansleep(ts->reset_gpio, 1);
1028
1029 error = regulator_enable(ts->avdd);
1030 if (error) {
1031 dev_err(&ts->client->dev,
1032 "failed to enable avdd regulator: %d\n", error);
1033 goto release_reset_gpio;
1034 }
1035
1036 error = regulator_enable(ts->vccio);
1037 if (error) {
1038 regulator_disable(ts->avdd);
1039 dev_err(&ts->client->dev,
1040 "failed to enable vccio regulator: %d\n", error);
1041 goto release_reset_gpio;
1042 }
1043
1044 udelay(RM_POWERON_DELAY_USEC);
1045
1046release_reset_gpio:
1047 gpiod_set_value_cansleep(ts->reset_gpio, 0);
1048
1049 if (error)
1050 return error;
1051
1052 msleep(RM_RESET_DELAY_MSEC);
1053
1054 return 0;
1055}
1056
1057static void raydium_i2c_power_off(void *_data)
1058{
1059 struct raydium_data *ts = _data;
1060
1061 if (ts->reset_gpio) {
1062 gpiod_set_value_cansleep(ts->reset_gpio, 1);
1063 regulator_disable(ts->vccio);
1064 regulator_disable(ts->avdd);
1065 }
1066}
1067
1068static int raydium_i2c_probe(struct i2c_client *client)
1069{
1070 union i2c_smbus_data dummy;
1071 struct raydium_data *ts;
1072 int error;
1073
1074 if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
1075 dev_err(&client->dev,
1076 "i2c check functionality error (need I2C_FUNC_I2C)\n");
1077 return -ENXIO;
1078 }
1079
1080 ts = devm_kzalloc(&client->dev, sizeof(*ts), GFP_KERNEL);
1081 if (!ts)
1082 return -ENOMEM;
1083
1084 mutex_init(&ts->sysfs_mutex);
1085
1086 ts->client = client;
1087 i2c_set_clientdata(client, ts);
1088
1089 ts->avdd = devm_regulator_get(&client->dev, "avdd");
1090 if (IS_ERR(ts->avdd)) {
1091 error = PTR_ERR(ts->avdd);
1092 if (error != -EPROBE_DEFER)
1093 dev_err(&client->dev,
1094 "Failed to get 'avdd' regulator: %d\n", error);
1095 return error;
1096 }
1097
1098 ts->vccio = devm_regulator_get(&client->dev, "vccio");
1099 if (IS_ERR(ts->vccio)) {
1100 error = PTR_ERR(ts->vccio);
1101 if (error != -EPROBE_DEFER)
1102 dev_err(&client->dev,
1103 "Failed to get 'vccio' regulator: %d\n", error);
1104 return error;
1105 }
1106
1107 ts->reset_gpio = devm_gpiod_get_optional(&client->dev, "reset",
1108 GPIOD_OUT_LOW);
1109 if (IS_ERR(ts->reset_gpio)) {
1110 error = PTR_ERR(ts->reset_gpio);
1111 if (error != -EPROBE_DEFER)
1112 dev_err(&client->dev,
1113 "failed to get reset gpio: %d\n", error);
1114 return error;
1115 }
1116
1117 error = raydium_i2c_power_on(ts);
1118 if (error)
1119 return error;
1120
1121 error = devm_add_action_or_reset(&client->dev,
1122 raydium_i2c_power_off, ts);
1123 if (error) {
1124 dev_err(&client->dev,
1125 "failed to install power off action: %d\n", error);
1126 return error;
1127 }
1128
1129 /* Make sure there is something at this address */
1130 if (i2c_smbus_xfer(client->adapter, client->addr, 0,
1131 I2C_SMBUS_READ, 0, I2C_SMBUS_BYTE, &dummy) < 0) {
1132 dev_err(&client->dev, "nothing at this address\n");
1133 return -ENXIO;
1134 }
1135
1136 error = raydium_i2c_initialize(ts);
1137 if (error) {
1138 dev_err(&client->dev, "failed to initialize: %d\n", error);
1139 return error;
1140 }
1141
1142 ts->report_data = devm_kmalloc(&client->dev,
1143 ts->pkg_size, GFP_KERNEL);
1144 if (!ts->report_data)
1145 return -ENOMEM;
1146
1147 ts->input = devm_input_allocate_device(&client->dev);
1148 if (!ts->input) {
1149 dev_err(&client->dev, "Failed to allocate input device\n");
1150 return -ENOMEM;
1151 }
1152
1153 ts->input->name = "Raydium Touchscreen";
1154 ts->input->id.bustype = BUS_I2C;
1155
1156 input_set_abs_params(ts->input, ABS_MT_POSITION_X,
1157 0, le16_to_cpu(ts->info.x_max), 0, 0);
1158 input_set_abs_params(ts->input, ABS_MT_POSITION_Y,
1159 0, le16_to_cpu(ts->info.y_max), 0, 0);
1160 input_abs_set_res(ts->input, ABS_MT_POSITION_X, ts->info.x_res);
1161 input_abs_set_res(ts->input, ABS_MT_POSITION_Y, ts->info.y_res);
1162
1163 input_set_abs_params(ts->input, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
1164 input_set_abs_params(ts->input, ABS_MT_PRESSURE, 0, 255, 0, 0);
1165
1166 error = input_mt_init_slots(ts->input, RM_MAX_TOUCH_NUM,
1167 INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
1168 if (error) {
1169 dev_err(&client->dev,
1170 "failed to initialize MT slots: %d\n", error);
1171 return error;
1172 }
1173
1174 error = input_register_device(ts->input);
1175 if (error) {
1176 dev_err(&client->dev,
1177 "unable to register input device: %d\n", error);
1178 return error;
1179 }
1180
1181 error = devm_request_threaded_irq(&client->dev, client->irq,
1182 NULL, raydium_i2c_irq,
1183 IRQF_ONESHOT, client->name, ts);
1184 if (error) {
1185 dev_err(&client->dev, "Failed to register interrupt\n");
1186 return error;
1187 }
1188
1189 error = devm_device_add_group(&client->dev,
1190 &raydium_i2c_attribute_group);
1191 if (error) {
1192 dev_err(&client->dev, "failed to create sysfs attributes: %d\n",
1193 error);
1194 return error;
1195 }
1196
1197 return 0;
1198}
1199
1200static void __maybe_unused raydium_enter_sleep(struct i2c_client *client)
1201{
1202 static const u8 sleep_cmd[] = { 0x5A, 0xff, 0x00, 0x0f };
1203 int error;
1204
1205 error = raydium_i2c_send(client, RM_CMD_ENTER_SLEEP,
1206 sleep_cmd, sizeof(sleep_cmd));
1207 if (error)
1208 dev_err(&client->dev,
1209 "sleep command failed: %d\n", error);
1210}
1211
1212static int __maybe_unused raydium_i2c_suspend(struct device *dev)
1213{
1214 struct i2c_client *client = to_i2c_client(dev);
1215 struct raydium_data *ts = i2c_get_clientdata(client);
1216
1217 /* Sleep is not available in BLDR recovery mode */
1218 if (ts->boot_mode != RAYDIUM_TS_MAIN)
1219 return -EBUSY;
1220
1221 disable_irq(client->irq);
1222
1223 if (device_may_wakeup(dev)) {
1224 raydium_enter_sleep(client);
1225 } else {
1226 raydium_i2c_power_off(ts);
1227 }
1228
1229 return 0;
1230}
1231
1232static int __maybe_unused raydium_i2c_resume(struct device *dev)
1233{
1234 struct i2c_client *client = to_i2c_client(dev);
1235 struct raydium_data *ts = i2c_get_clientdata(client);
1236
1237 if (device_may_wakeup(dev)) {
1238 raydium_i2c_sw_reset(client);
1239 } else {
1240 raydium_i2c_power_on(ts);
1241 raydium_i2c_initialize(ts);
1242 }
1243
1244 enable_irq(client->irq);
1245
1246 return 0;
1247}
1248
1249static SIMPLE_DEV_PM_OPS(raydium_i2c_pm_ops,
1250 raydium_i2c_suspend, raydium_i2c_resume);
1251
1252static const struct i2c_device_id raydium_i2c_id[] = {
1253 { "raydium_i2c", 0 },
1254 { "rm32380", 0 },
1255 { /* sentinel */ }
1256};
1257MODULE_DEVICE_TABLE(i2c, raydium_i2c_id);
1258
1259#ifdef CONFIG_ACPI
1260static const struct acpi_device_id raydium_acpi_id[] = {
1261 { "RAYD0001", 0 },
1262 { /* sentinel */ }
1263};
1264MODULE_DEVICE_TABLE(acpi, raydium_acpi_id);
1265#endif
1266
1267#ifdef CONFIG_OF
1268static const struct of_device_id raydium_of_match[] = {
1269 { .compatible = "raydium,rm32380", },
1270 { /* sentinel */ }
1271};
1272MODULE_DEVICE_TABLE(of, raydium_of_match);
1273#endif
1274
1275static struct i2c_driver raydium_i2c_driver = {
1276 .probe_new = raydium_i2c_probe,
1277 .id_table = raydium_i2c_id,
1278 .driver = {
1279 .name = "raydium_ts",
1280 .pm = &raydium_i2c_pm_ops,
1281 .acpi_match_table = ACPI_PTR(raydium_acpi_id),
1282 .of_match_table = of_match_ptr(raydium_of_match),
1283 },
1284};
1285module_i2c_driver(raydium_i2c_driver);
1286
1287MODULE_AUTHOR("Raydium");
1288MODULE_DESCRIPTION("Raydium I2c Touchscreen driver");
1289MODULE_LICENSE("GPL v2");
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Raydium touchscreen I2C driver.
4 *
5 * Copyright (C) 2012-2014, Raydium Semiconductor Corporation.
6 *
7 * Raydium reserves the right to make changes without further notice
8 * to the materials described herein. Raydium does not assume any
9 * liability arising out of the application described herein.
10 *
11 * Contact Raydium Semiconductor Corporation at www.rad-ic.com
12 */
13
14#include <linux/acpi.h>
15#include <linux/delay.h>
16#include <linux/firmware.h>
17#include <linux/gpio/consumer.h>
18#include <linux/i2c.h>
19#include <linux/input.h>
20#include <linux/input/mt.h>
21#include <linux/interrupt.h>
22#include <linux/module.h>
23#include <linux/of.h>
24#include <linux/regulator/consumer.h>
25#include <linux/slab.h>
26#include <asm/unaligned.h>
27
28/* Slave I2C mode */
29#define RM_BOOT_BLDR 0x02
30#define RM_BOOT_MAIN 0x03
31
32/* I2C bootoloader commands */
33#define RM_CMD_BOOT_PAGE_WRT 0x0B /* send bl page write */
34#define RM_CMD_BOOT_WRT 0x11 /* send bl write */
35#define RM_CMD_BOOT_ACK 0x22 /* send ack*/
36#define RM_CMD_BOOT_CHK 0x33 /* send data check */
37#define RM_CMD_BOOT_READ 0x44 /* send wait bl data ready*/
38
39#define RM_BOOT_RDY 0xFF /* bl data ready */
40
41/* I2C main commands */
42#define RM_CMD_QUERY_BANK 0x2B
43#define RM_CMD_DATA_BANK 0x4D
44#define RM_CMD_ENTER_SLEEP 0x4E
45#define RM_CMD_BANK_SWITCH 0xAA
46
47#define RM_RESET_MSG_ADDR 0x40000004
48
49#define RM_MAX_READ_SIZE 56
50#define RM_PACKET_CRC_SIZE 2
51
52/* Touch relative info */
53#define RM_MAX_RETRIES 3
54#define RM_MAX_TOUCH_NUM 10
55#define RM_BOOT_DELAY_MS 100
56
57/* Offsets in contact data */
58#define RM_CONTACT_STATE_POS 0
59#define RM_CONTACT_X_POS 1
60#define RM_CONTACT_Y_POS 3
61#define RM_CONTACT_PRESSURE_POS 5
62#define RM_CONTACT_WIDTH_X_POS 6
63#define RM_CONTACT_WIDTH_Y_POS 7
64
65/* Bootloader relative info */
66#define RM_BL_WRT_CMD_SIZE 3 /* bl flash wrt cmd size */
67#define RM_BL_WRT_PKG_SIZE 32 /* bl wrt pkg size */
68#define RM_BL_WRT_LEN (RM_BL_WRT_PKG_SIZE + RM_BL_WRT_CMD_SIZE)
69#define RM_FW_PAGE_SIZE 128
70#define RM_MAX_FW_RETRIES 30
71#define RM_MAX_FW_SIZE 0xD000
72
73#define RM_POWERON_DELAY_USEC 500
74#define RM_RESET_DELAY_MSEC 50
75
76enum raydium_bl_cmd {
77 BL_HEADER = 0,
78 BL_PAGE_STR,
79 BL_PKG_IDX,
80 BL_DATA_STR,
81};
82
83enum raydium_bl_ack {
84 RAYDIUM_ACK_NULL = 0,
85 RAYDIUM_WAIT_READY,
86 RAYDIUM_PATH_READY,
87};
88
89enum raydium_boot_mode {
90 RAYDIUM_TS_MAIN = 0,
91 RAYDIUM_TS_BLDR,
92};
93
94/* Response to RM_CMD_DATA_BANK request */
95struct raydium_data_info {
96 __le32 data_bank_addr;
97 u8 pkg_size;
98 u8 tp_info_size;
99};
100
101struct raydium_info {
102 __le32 hw_ver; /*device version */
103 u8 main_ver;
104 u8 sub_ver;
105 __le16 ft_ver; /* test version */
106 u8 x_num;
107 u8 y_num;
108 __le16 x_max;
109 __le16 y_max;
110 u8 x_res; /* units/mm */
111 u8 y_res; /* units/mm */
112};
113
114/* struct raydium_data - represents state of Raydium touchscreen device */
115struct raydium_data {
116 struct i2c_client *client;
117 struct input_dev *input;
118
119 struct regulator *avdd;
120 struct regulator *vccio;
121 struct gpio_desc *reset_gpio;
122
123 struct raydium_info info;
124
125 struct mutex sysfs_mutex;
126
127 u8 *report_data;
128
129 u32 data_bank_addr;
130 u8 report_size;
131 u8 contact_size;
132 u8 pkg_size;
133
134 enum raydium_boot_mode boot_mode;
135
136 bool wake_irq_enabled;
137};
138
139static int raydium_i2c_send(struct i2c_client *client,
140 u8 addr, const void *data, size_t len)
141{
142 u8 *buf;
143 int tries = 0;
144 int ret;
145
146 buf = kmalloc(len + 1, GFP_KERNEL);
147 if (!buf)
148 return -ENOMEM;
149
150 buf[0] = addr;
151 memcpy(buf + 1, data, len);
152
153 do {
154 ret = i2c_master_send(client, buf, len + 1);
155 if (likely(ret == len + 1))
156 break;
157
158 msleep(20);
159 } while (++tries < RM_MAX_RETRIES);
160
161 kfree(buf);
162
163 if (unlikely(ret != len + 1)) {
164 if (ret >= 0)
165 ret = -EIO;
166 dev_err(&client->dev, "%s failed: %d\n", __func__, ret);
167 return ret;
168 }
169
170 return 0;
171}
172
173static int raydium_i2c_read(struct i2c_client *client,
174 u8 addr, void *data, size_t len)
175{
176 struct i2c_msg xfer[] = {
177 {
178 .addr = client->addr,
179 .len = 1,
180 .buf = &addr,
181 },
182 {
183 .addr = client->addr,
184 .flags = I2C_M_RD,
185 .len = len,
186 .buf = data,
187 }
188 };
189 int ret;
190
191 ret = i2c_transfer(client->adapter, xfer, ARRAY_SIZE(xfer));
192 if (unlikely(ret != ARRAY_SIZE(xfer)))
193 return ret < 0 ? ret : -EIO;
194
195 return 0;
196}
197
198static int raydium_i2c_read_message(struct i2c_client *client,
199 u32 addr, void *data, size_t len)
200{
201 __be32 be_addr;
202 size_t xfer_len;
203 int error;
204
205 while (len) {
206 xfer_len = min_t(size_t, len, RM_MAX_READ_SIZE);
207
208 be_addr = cpu_to_be32(addr);
209
210 error = raydium_i2c_send(client, RM_CMD_BANK_SWITCH,
211 &be_addr, sizeof(be_addr));
212 if (!error)
213 error = raydium_i2c_read(client, addr & 0xff,
214 data, xfer_len);
215 if (error)
216 return error;
217
218 len -= xfer_len;
219 data += xfer_len;
220 addr += xfer_len;
221 }
222
223 return 0;
224}
225
226static int raydium_i2c_send_message(struct i2c_client *client,
227 u32 addr, const void *data, size_t len)
228{
229 __be32 be_addr = cpu_to_be32(addr);
230 int error;
231
232 error = raydium_i2c_send(client, RM_CMD_BANK_SWITCH,
233 &be_addr, sizeof(be_addr));
234 if (!error)
235 error = raydium_i2c_send(client, addr & 0xff, data, len);
236
237 return error;
238}
239
240static int raydium_i2c_sw_reset(struct i2c_client *client)
241{
242 const u8 soft_rst_cmd = 0x01;
243 int error;
244
245 error = raydium_i2c_send_message(client, RM_RESET_MSG_ADDR,
246 &soft_rst_cmd, sizeof(soft_rst_cmd));
247 if (error) {
248 dev_err(&client->dev, "software reset failed: %d\n", error);
249 return error;
250 }
251
252 msleep(RM_RESET_DELAY_MSEC);
253
254 return 0;
255}
256
257static int raydium_i2c_query_ts_info(struct raydium_data *ts)
258{
259 struct i2c_client *client = ts->client;
260 struct raydium_data_info data_info;
261 __le32 query_bank_addr;
262
263 int error, retry_cnt;
264
265 for (retry_cnt = 0; retry_cnt < RM_MAX_RETRIES; retry_cnt++) {
266 error = raydium_i2c_read(client, RM_CMD_DATA_BANK,
267 &data_info, sizeof(data_info));
268 if (error)
269 continue;
270
271 /*
272 * Warn user if we already allocated memory for reports and
273 * then the size changed (due to firmware update?) and keep
274 * old size instead.
275 */
276 if (ts->report_data && ts->pkg_size != data_info.pkg_size) {
277 dev_warn(&client->dev,
278 "report size changes, was: %d, new: %d\n",
279 ts->pkg_size, data_info.pkg_size);
280 } else {
281 ts->pkg_size = data_info.pkg_size;
282 ts->report_size = ts->pkg_size - RM_PACKET_CRC_SIZE;
283 }
284
285 ts->contact_size = data_info.tp_info_size;
286 ts->data_bank_addr = le32_to_cpu(data_info.data_bank_addr);
287
288 dev_dbg(&client->dev,
289 "data_bank_addr: %#08x, report_size: %d, contact_size: %d\n",
290 ts->data_bank_addr, ts->report_size, ts->contact_size);
291
292 error = raydium_i2c_read(client, RM_CMD_QUERY_BANK,
293 &query_bank_addr,
294 sizeof(query_bank_addr));
295 if (error)
296 continue;
297
298 error = raydium_i2c_read_message(client,
299 le32_to_cpu(query_bank_addr),
300 &ts->info, sizeof(ts->info));
301 if (error)
302 continue;
303
304 return 0;
305 }
306
307 dev_err(&client->dev, "failed to query device parameters: %d\n", error);
308 return error;
309}
310
311static int raydium_i2c_check_fw_status(struct raydium_data *ts)
312{
313 struct i2c_client *client = ts->client;
314 static const u8 bl_ack = 0x62;
315 static const u8 main_ack = 0x66;
316 u8 buf[4];
317 int error;
318
319 error = raydium_i2c_read(client, RM_CMD_BOOT_READ, buf, sizeof(buf));
320 if (!error) {
321 if (buf[0] == bl_ack)
322 ts->boot_mode = RAYDIUM_TS_BLDR;
323 else if (buf[0] == main_ack)
324 ts->boot_mode = RAYDIUM_TS_MAIN;
325 return 0;
326 }
327
328 return error;
329}
330
331static int raydium_i2c_initialize(struct raydium_data *ts)
332{
333 struct i2c_client *client = ts->client;
334 int error, retry_cnt;
335
336 for (retry_cnt = 0; retry_cnt < RM_MAX_RETRIES; retry_cnt++) {
337 /* Wait for Hello packet */
338 msleep(RM_BOOT_DELAY_MS);
339
340 error = raydium_i2c_check_fw_status(ts);
341 if (error) {
342 dev_err(&client->dev,
343 "failed to read 'hello' packet: %d\n", error);
344 continue;
345 }
346
347 if (ts->boot_mode == RAYDIUM_TS_BLDR ||
348 ts->boot_mode == RAYDIUM_TS_MAIN) {
349 break;
350 }
351 }
352
353 if (error)
354 ts->boot_mode = RAYDIUM_TS_BLDR;
355
356 if (ts->boot_mode == RAYDIUM_TS_BLDR) {
357 ts->info.hw_ver = cpu_to_le32(0xffffffffUL);
358 ts->info.main_ver = 0xff;
359 ts->info.sub_ver = 0xff;
360 } else {
361 raydium_i2c_query_ts_info(ts);
362 }
363
364 return error;
365}
366
367static int raydium_i2c_bl_chk_state(struct i2c_client *client,
368 enum raydium_bl_ack state)
369{
370 static const u8 ack_ok[] = { 0xFF, 0x39, 0x30, 0x30, 0x54 };
371 u8 rbuf[sizeof(ack_ok)];
372 u8 retry;
373 int error;
374
375 for (retry = 0; retry < RM_MAX_FW_RETRIES; retry++) {
376 switch (state) {
377 case RAYDIUM_ACK_NULL:
378 return 0;
379
380 case RAYDIUM_WAIT_READY:
381 error = raydium_i2c_read(client, RM_CMD_BOOT_CHK,
382 &rbuf[0], 1);
383 if (!error && rbuf[0] == RM_BOOT_RDY)
384 return 0;
385
386 break;
387
388 case RAYDIUM_PATH_READY:
389 error = raydium_i2c_read(client, RM_CMD_BOOT_CHK,
390 rbuf, sizeof(rbuf));
391 if (!error && !memcmp(rbuf, ack_ok, sizeof(ack_ok)))
392 return 0;
393
394 break;
395
396 default:
397 dev_err(&client->dev, "%s: invalid target state %d\n",
398 __func__, state);
399 return -EINVAL;
400 }
401
402 msleep(20);
403 }
404
405 return -ETIMEDOUT;
406}
407
408static int raydium_i2c_write_object(struct i2c_client *client,
409 const void *data, size_t len,
410 enum raydium_bl_ack state)
411{
412 int error;
413
414 error = raydium_i2c_send(client, RM_CMD_BOOT_WRT, data, len);
415 if (error) {
416 dev_err(&client->dev, "WRT obj command failed: %d\n",
417 error);
418 return error;
419 }
420
421 error = raydium_i2c_send(client, RM_CMD_BOOT_ACK, NULL, 0);
422 if (error) {
423 dev_err(&client->dev, "Ack obj command failed: %d\n", error);
424 return error;
425 }
426
427 error = raydium_i2c_bl_chk_state(client, state);
428 if (error) {
429 dev_err(&client->dev, "BL check state failed: %d\n", error);
430 return error;
431 }
432 return 0;
433}
434
435static int raydium_i2c_boot_trigger(struct i2c_client *client)
436{
437 static const u8 cmd[7][6] = {
438 { 0x08, 0x0C, 0x09, 0x00, 0x50, 0xD7 },
439 { 0x08, 0x04, 0x09, 0x00, 0x50, 0xA5 },
440 { 0x08, 0x04, 0x09, 0x00, 0x50, 0x00 },
441 { 0x08, 0x04, 0x09, 0x00, 0x50, 0xA5 },
442 { 0x08, 0x0C, 0x09, 0x00, 0x50, 0x00 },
443 { 0x06, 0x01, 0x00, 0x00, 0x00, 0x00 },
444 { 0x02, 0xA2, 0x00, 0x00, 0x00, 0x00 },
445 };
446 int i;
447 int error;
448
449 for (i = 0; i < 7; i++) {
450 error = raydium_i2c_write_object(client, cmd[i], sizeof(cmd[i]),
451 RAYDIUM_WAIT_READY);
452 if (error) {
453 dev_err(&client->dev,
454 "boot trigger failed at step %d: %d\n",
455 i, error);
456 return error;
457 }
458 }
459
460 return 0;
461}
462
463static int raydium_i2c_fw_trigger(struct i2c_client *client)
464{
465 static const u8 cmd[5][11] = {
466 { 0, 0x09, 0x71, 0x0C, 0x09, 0x00, 0x50, 0xD7, 0, 0, 0 },
467 { 0, 0x09, 0x71, 0x04, 0x09, 0x00, 0x50, 0xA5, 0, 0, 0 },
468 { 0, 0x09, 0x71, 0x04, 0x09, 0x00, 0x50, 0x00, 0, 0, 0 },
469 { 0, 0x09, 0x71, 0x04, 0x09, 0x00, 0x50, 0xA5, 0, 0, 0 },
470 { 0, 0x09, 0x71, 0x0C, 0x09, 0x00, 0x50, 0x00, 0, 0, 0 },
471 };
472 int i;
473 int error;
474
475 for (i = 0; i < 5; i++) {
476 error = raydium_i2c_write_object(client, cmd[i], sizeof(cmd[i]),
477 RAYDIUM_ACK_NULL);
478 if (error) {
479 dev_err(&client->dev,
480 "fw trigger failed at step %d: %d\n",
481 i, error);
482 return error;
483 }
484 }
485
486 return 0;
487}
488
489static int raydium_i2c_check_path(struct i2c_client *client)
490{
491 static const u8 cmd[] = { 0x09, 0x00, 0x09, 0x00, 0x50, 0x10, 0x00 };
492 int error;
493
494 error = raydium_i2c_write_object(client, cmd, sizeof(cmd),
495 RAYDIUM_PATH_READY);
496 if (error) {
497 dev_err(&client->dev, "check path command failed: %d\n", error);
498 return error;
499 }
500
501 return 0;
502}
503
504static int raydium_i2c_enter_bl(struct i2c_client *client)
505{
506 static const u8 cal_cmd[] = { 0x00, 0x01, 0x52 };
507 int error;
508
509 error = raydium_i2c_write_object(client, cal_cmd, sizeof(cal_cmd),
510 RAYDIUM_ACK_NULL);
511 if (error) {
512 dev_err(&client->dev, "enter bl command failed: %d\n", error);
513 return error;
514 }
515
516 msleep(RM_BOOT_DELAY_MS);
517 return 0;
518}
519
520static int raydium_i2c_leave_bl(struct i2c_client *client)
521{
522 static const u8 leave_cmd[] = { 0x05, 0x00 };
523 int error;
524
525 error = raydium_i2c_write_object(client, leave_cmd, sizeof(leave_cmd),
526 RAYDIUM_ACK_NULL);
527 if (error) {
528 dev_err(&client->dev, "leave bl command failed: %d\n", error);
529 return error;
530 }
531
532 msleep(RM_BOOT_DELAY_MS);
533 return 0;
534}
535
536static int raydium_i2c_write_checksum(struct i2c_client *client,
537 size_t length, u16 checksum)
538{
539 u8 checksum_cmd[] = { 0x00, 0x05, 0x6D, 0x00, 0x00, 0x00, 0x00 };
540 int error;
541
542 put_unaligned_le16(length, &checksum_cmd[3]);
543 put_unaligned_le16(checksum, &checksum_cmd[5]);
544
545 error = raydium_i2c_write_object(client,
546 checksum_cmd, sizeof(checksum_cmd),
547 RAYDIUM_ACK_NULL);
548 if (error) {
549 dev_err(&client->dev, "failed to write checksum: %d\n",
550 error);
551 return error;
552 }
553
554 return 0;
555}
556
557static int raydium_i2c_disable_watch_dog(struct i2c_client *client)
558{
559 static const u8 cmd[] = { 0x0A, 0xAA };
560 int error;
561
562 error = raydium_i2c_write_object(client, cmd, sizeof(cmd),
563 RAYDIUM_WAIT_READY);
564 if (error) {
565 dev_err(&client->dev, "disable watchdog command failed: %d\n",
566 error);
567 return error;
568 }
569
570 return 0;
571}
572
573static int raydium_i2c_fw_write_page(struct i2c_client *client,
574 u16 page_idx, const void *data, size_t len)
575{
576 u8 buf[RM_BL_WRT_LEN];
577 size_t xfer_len;
578 int error;
579 int i;
580
581 BUILD_BUG_ON((RM_FW_PAGE_SIZE % RM_BL_WRT_PKG_SIZE) != 0);
582
583 for (i = 0; i < RM_FW_PAGE_SIZE / RM_BL_WRT_PKG_SIZE; i++) {
584 buf[BL_HEADER] = RM_CMD_BOOT_PAGE_WRT;
585 buf[BL_PAGE_STR] = page_idx ? 0xff : 0;
586 buf[BL_PKG_IDX] = i + 1;
587
588 xfer_len = min_t(size_t, len, RM_BL_WRT_PKG_SIZE);
589 memcpy(&buf[BL_DATA_STR], data, xfer_len);
590 if (len < RM_BL_WRT_PKG_SIZE)
591 memset(&buf[BL_DATA_STR + xfer_len], 0xff,
592 RM_BL_WRT_PKG_SIZE - xfer_len);
593
594 error = raydium_i2c_write_object(client, buf, RM_BL_WRT_LEN,
595 RAYDIUM_WAIT_READY);
596 if (error) {
597 dev_err(&client->dev,
598 "page write command failed for page %d, chunk %d: %d\n",
599 page_idx, i, error);
600 return error;
601 }
602
603 data += xfer_len;
604 len -= xfer_len;
605 }
606
607 return error;
608}
609
610static u16 raydium_calc_chksum(const u8 *buf, u16 len)
611{
612 u16 checksum = 0;
613 u16 i;
614
615 for (i = 0; i < len; i++)
616 checksum += buf[i];
617
618 return checksum;
619}
620
621static int raydium_i2c_do_update_firmware(struct raydium_data *ts,
622 const struct firmware *fw)
623{
624 struct i2c_client *client = ts->client;
625 const void *data;
626 size_t data_len;
627 size_t len;
628 int page_nr;
629 int i;
630 int error;
631 u16 fw_checksum;
632
633 if (fw->size == 0 || fw->size > RM_MAX_FW_SIZE) {
634 dev_err(&client->dev, "Invalid firmware length\n");
635 return -EINVAL;
636 }
637
638 error = raydium_i2c_check_fw_status(ts);
639 if (error) {
640 dev_err(&client->dev, "Unable to access IC %d\n", error);
641 return error;
642 }
643
644 if (ts->boot_mode == RAYDIUM_TS_MAIN) {
645 for (i = 0; i < RM_MAX_RETRIES; i++) {
646 error = raydium_i2c_enter_bl(client);
647 if (!error) {
648 error = raydium_i2c_check_fw_status(ts);
649 if (error) {
650 dev_err(&client->dev,
651 "unable to access IC: %d\n",
652 error);
653 return error;
654 }
655
656 if (ts->boot_mode == RAYDIUM_TS_BLDR)
657 break;
658 }
659 }
660
661 if (ts->boot_mode == RAYDIUM_TS_MAIN) {
662 dev_err(&client->dev,
663 "failed to jump to boot loader: %d\n",
664 error);
665 return -EIO;
666 }
667 }
668
669 error = raydium_i2c_disable_watch_dog(client);
670 if (error)
671 return error;
672
673 error = raydium_i2c_check_path(client);
674 if (error)
675 return error;
676
677 error = raydium_i2c_boot_trigger(client);
678 if (error) {
679 dev_err(&client->dev, "send boot trigger fail: %d\n", error);
680 return error;
681 }
682
683 msleep(RM_BOOT_DELAY_MS);
684
685 data = fw->data;
686 data_len = fw->size;
687 page_nr = 0;
688
689 while (data_len) {
690 len = min_t(size_t, data_len, RM_FW_PAGE_SIZE);
691
692 error = raydium_i2c_fw_write_page(client, page_nr++, data, len);
693 if (error)
694 return error;
695
696 msleep(20);
697
698 data += len;
699 data_len -= len;
700 }
701
702 error = raydium_i2c_leave_bl(client);
703 if (error) {
704 dev_err(&client->dev,
705 "failed to leave boot loader: %d\n", error);
706 return error;
707 }
708
709 dev_dbg(&client->dev, "left boot loader mode\n");
710 msleep(RM_BOOT_DELAY_MS);
711
712 error = raydium_i2c_check_fw_status(ts);
713 if (error) {
714 dev_err(&client->dev,
715 "failed to check fw status after write: %d\n",
716 error);
717 return error;
718 }
719
720 if (ts->boot_mode != RAYDIUM_TS_MAIN) {
721 dev_err(&client->dev,
722 "failed to switch to main fw after writing firmware: %d\n",
723 error);
724 return -EINVAL;
725 }
726
727 error = raydium_i2c_fw_trigger(client);
728 if (error) {
729 dev_err(&client->dev, "failed to trigger fw: %d\n", error);
730 return error;
731 }
732
733 fw_checksum = raydium_calc_chksum(fw->data, fw->size);
734
735 error = raydium_i2c_write_checksum(client, fw->size, fw_checksum);
736 if (error)
737 return error;
738
739 return 0;
740}
741
742static int raydium_i2c_fw_update(struct raydium_data *ts)
743{
744 struct i2c_client *client = ts->client;
745 const struct firmware *fw = NULL;
746 char *fw_file;
747 int error;
748
749 fw_file = kasprintf(GFP_KERNEL, "raydium_%#04x.fw",
750 le32_to_cpu(ts->info.hw_ver));
751 if (!fw_file)
752 return -ENOMEM;
753
754 dev_dbg(&client->dev, "firmware name: %s\n", fw_file);
755
756 error = request_firmware(&fw, fw_file, &client->dev);
757 if (error) {
758 dev_err(&client->dev, "Unable to open firmware %s\n", fw_file);
759 goto out_free_fw_file;
760 }
761
762 disable_irq(client->irq);
763
764 error = raydium_i2c_do_update_firmware(ts, fw);
765 if (error) {
766 dev_err(&client->dev, "firmware update failed: %d\n", error);
767 ts->boot_mode = RAYDIUM_TS_BLDR;
768 goto out_enable_irq;
769 }
770
771 error = raydium_i2c_initialize(ts);
772 if (error) {
773 dev_err(&client->dev,
774 "failed to initialize device after firmware update: %d\n",
775 error);
776 ts->boot_mode = RAYDIUM_TS_BLDR;
777 goto out_enable_irq;
778 }
779
780 ts->boot_mode = RAYDIUM_TS_MAIN;
781
782out_enable_irq:
783 enable_irq(client->irq);
784 msleep(100);
785
786 release_firmware(fw);
787
788out_free_fw_file:
789 kfree(fw_file);
790
791 return error;
792}
793
794static void raydium_mt_event(struct raydium_data *ts)
795{
796 int i;
797
798 for (i = 0; i < ts->report_size / ts->contact_size; i++) {
799 u8 *contact = &ts->report_data[ts->contact_size * i];
800 bool state = contact[RM_CONTACT_STATE_POS];
801 u8 wx, wy;
802
803 input_mt_slot(ts->input, i);
804 input_mt_report_slot_state(ts->input, MT_TOOL_FINGER, state);
805
806 if (!state)
807 continue;
808
809 input_report_abs(ts->input, ABS_MT_POSITION_X,
810 get_unaligned_le16(&contact[RM_CONTACT_X_POS]));
811 input_report_abs(ts->input, ABS_MT_POSITION_Y,
812 get_unaligned_le16(&contact[RM_CONTACT_Y_POS]));
813 input_report_abs(ts->input, ABS_MT_PRESSURE,
814 contact[RM_CONTACT_PRESSURE_POS]);
815
816 wx = contact[RM_CONTACT_WIDTH_X_POS];
817 wy = contact[RM_CONTACT_WIDTH_Y_POS];
818
819 input_report_abs(ts->input, ABS_MT_TOUCH_MAJOR, max(wx, wy));
820 input_report_abs(ts->input, ABS_MT_TOUCH_MINOR, min(wx, wy));
821 }
822
823 input_mt_sync_frame(ts->input);
824 input_sync(ts->input);
825}
826
827static irqreturn_t raydium_i2c_irq(int irq, void *_dev)
828{
829 struct raydium_data *ts = _dev;
830 int error;
831 u16 fw_crc;
832 u16 calc_crc;
833
834 if (ts->boot_mode != RAYDIUM_TS_MAIN)
835 goto out;
836
837 error = raydium_i2c_read_message(ts->client, ts->data_bank_addr,
838 ts->report_data, ts->pkg_size);
839 if (error)
840 goto out;
841
842 fw_crc = get_unaligned_le16(&ts->report_data[ts->report_size]);
843 calc_crc = raydium_calc_chksum(ts->report_data, ts->report_size);
844 if (unlikely(fw_crc != calc_crc)) {
845 dev_warn(&ts->client->dev,
846 "%s: invalid packet crc %#04x vs %#04x\n",
847 __func__, calc_crc, fw_crc);
848 goto out;
849 }
850
851 raydium_mt_event(ts);
852
853out:
854 return IRQ_HANDLED;
855}
856
857static ssize_t raydium_i2c_fw_ver_show(struct device *dev,
858 struct device_attribute *attr, char *buf)
859{
860 struct i2c_client *client = to_i2c_client(dev);
861 struct raydium_data *ts = i2c_get_clientdata(client);
862
863 return sprintf(buf, "%d.%d\n", ts->info.main_ver, ts->info.sub_ver);
864}
865
866static ssize_t raydium_i2c_hw_ver_show(struct device *dev,
867 struct device_attribute *attr, char *buf)
868{
869 struct i2c_client *client = to_i2c_client(dev);
870 struct raydium_data *ts = i2c_get_clientdata(client);
871
872 return sprintf(buf, "%#04x\n", le32_to_cpu(ts->info.hw_ver));
873}
874
875static ssize_t raydium_i2c_boot_mode_show(struct device *dev,
876 struct device_attribute *attr,
877 char *buf)
878{
879 struct i2c_client *client = to_i2c_client(dev);
880 struct raydium_data *ts = i2c_get_clientdata(client);
881
882 return sprintf(buf, "%s\n",
883 ts->boot_mode == RAYDIUM_TS_MAIN ?
884 "Normal" : "Recovery");
885}
886
887static ssize_t raydium_i2c_update_fw_store(struct device *dev,
888 struct device_attribute *attr,
889 const char *buf, size_t count)
890{
891 struct i2c_client *client = to_i2c_client(dev);
892 struct raydium_data *ts = i2c_get_clientdata(client);
893 int error;
894
895 error = mutex_lock_interruptible(&ts->sysfs_mutex);
896 if (error)
897 return error;
898
899 error = raydium_i2c_fw_update(ts);
900
901 mutex_unlock(&ts->sysfs_mutex);
902
903 return error ?: count;
904}
905
906static ssize_t raydium_i2c_calibrate_store(struct device *dev,
907 struct device_attribute *attr,
908 const char *buf, size_t count)
909{
910 struct i2c_client *client = to_i2c_client(dev);
911 struct raydium_data *ts = i2c_get_clientdata(client);
912 static const u8 cal_cmd[] = { 0x00, 0x01, 0x9E };
913 int error;
914
915 error = mutex_lock_interruptible(&ts->sysfs_mutex);
916 if (error)
917 return error;
918
919 error = raydium_i2c_write_object(client, cal_cmd, sizeof(cal_cmd),
920 RAYDIUM_WAIT_READY);
921 if (error)
922 dev_err(&client->dev, "calibrate command failed: %d\n", error);
923
924 mutex_unlock(&ts->sysfs_mutex);
925 return error ?: count;
926}
927
928static DEVICE_ATTR(fw_version, S_IRUGO, raydium_i2c_fw_ver_show, NULL);
929static DEVICE_ATTR(hw_version, S_IRUGO, raydium_i2c_hw_ver_show, NULL);
930static DEVICE_ATTR(boot_mode, S_IRUGO, raydium_i2c_boot_mode_show, NULL);
931static DEVICE_ATTR(update_fw, S_IWUSR, NULL, raydium_i2c_update_fw_store);
932static DEVICE_ATTR(calibrate, S_IWUSR, NULL, raydium_i2c_calibrate_store);
933
934static struct attribute *raydium_i2c_attributes[] = {
935 &dev_attr_update_fw.attr,
936 &dev_attr_boot_mode.attr,
937 &dev_attr_fw_version.attr,
938 &dev_attr_hw_version.attr,
939 &dev_attr_calibrate.attr,
940 NULL
941};
942
943static const struct attribute_group raydium_i2c_attribute_group = {
944 .attrs = raydium_i2c_attributes,
945};
946
947static int raydium_i2c_power_on(struct raydium_data *ts)
948{
949 int error;
950
951 if (!ts->reset_gpio)
952 return 0;
953
954 gpiod_set_value_cansleep(ts->reset_gpio, 1);
955
956 error = regulator_enable(ts->avdd);
957 if (error) {
958 dev_err(&ts->client->dev,
959 "failed to enable avdd regulator: %d\n", error);
960 goto release_reset_gpio;
961 }
962
963 error = regulator_enable(ts->vccio);
964 if (error) {
965 regulator_disable(ts->avdd);
966 dev_err(&ts->client->dev,
967 "failed to enable vccio regulator: %d\n", error);
968 goto release_reset_gpio;
969 }
970
971 udelay(RM_POWERON_DELAY_USEC);
972
973release_reset_gpio:
974 gpiod_set_value_cansleep(ts->reset_gpio, 0);
975
976 if (error)
977 return error;
978
979 msleep(RM_RESET_DELAY_MSEC);
980
981 return 0;
982}
983
984static void raydium_i2c_power_off(void *_data)
985{
986 struct raydium_data *ts = _data;
987
988 if (ts->reset_gpio) {
989 gpiod_set_value_cansleep(ts->reset_gpio, 1);
990 regulator_disable(ts->vccio);
991 regulator_disable(ts->avdd);
992 }
993}
994
995static int raydium_i2c_probe(struct i2c_client *client,
996 const struct i2c_device_id *id)
997{
998 union i2c_smbus_data dummy;
999 struct raydium_data *ts;
1000 int error;
1001
1002 if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
1003 dev_err(&client->dev,
1004 "i2c check functionality error (need I2C_FUNC_I2C)\n");
1005 return -ENXIO;
1006 }
1007
1008 ts = devm_kzalloc(&client->dev, sizeof(*ts), GFP_KERNEL);
1009 if (!ts)
1010 return -ENOMEM;
1011
1012 mutex_init(&ts->sysfs_mutex);
1013
1014 ts->client = client;
1015 i2c_set_clientdata(client, ts);
1016
1017 ts->avdd = devm_regulator_get(&client->dev, "avdd");
1018 if (IS_ERR(ts->avdd)) {
1019 error = PTR_ERR(ts->avdd);
1020 if (error != -EPROBE_DEFER)
1021 dev_err(&client->dev,
1022 "Failed to get 'avdd' regulator: %d\n", error);
1023 return error;
1024 }
1025
1026 ts->vccio = devm_regulator_get(&client->dev, "vccio");
1027 if (IS_ERR(ts->vccio)) {
1028 error = PTR_ERR(ts->vccio);
1029 if (error != -EPROBE_DEFER)
1030 dev_err(&client->dev,
1031 "Failed to get 'vccio' regulator: %d\n", error);
1032 return error;
1033 }
1034
1035 ts->reset_gpio = devm_gpiod_get_optional(&client->dev, "reset",
1036 GPIOD_OUT_LOW);
1037 if (IS_ERR(ts->reset_gpio)) {
1038 error = PTR_ERR(ts->reset_gpio);
1039 if (error != -EPROBE_DEFER)
1040 dev_err(&client->dev,
1041 "failed to get reset gpio: %d\n", error);
1042 return error;
1043 }
1044
1045 error = raydium_i2c_power_on(ts);
1046 if (error)
1047 return error;
1048
1049 error = devm_add_action(&client->dev, raydium_i2c_power_off, ts);
1050 if (error) {
1051 dev_err(&client->dev,
1052 "failed to install power off action: %d\n", error);
1053 raydium_i2c_power_off(ts);
1054 return error;
1055 }
1056
1057 /* Make sure there is something at this address */
1058 if (i2c_smbus_xfer(client->adapter, client->addr, 0,
1059 I2C_SMBUS_READ, 0, I2C_SMBUS_BYTE, &dummy) < 0) {
1060 dev_err(&client->dev, "nothing at this address\n");
1061 return -ENXIO;
1062 }
1063
1064 error = raydium_i2c_initialize(ts);
1065 if (error) {
1066 dev_err(&client->dev, "failed to initialize: %d\n", error);
1067 return error;
1068 }
1069
1070 ts->report_data = devm_kmalloc(&client->dev,
1071 ts->pkg_size, GFP_KERNEL);
1072 if (!ts->report_data)
1073 return -ENOMEM;
1074
1075 ts->input = devm_input_allocate_device(&client->dev);
1076 if (!ts->input) {
1077 dev_err(&client->dev, "Failed to allocate input device\n");
1078 return -ENOMEM;
1079 }
1080
1081 ts->input->name = "Raydium Touchscreen";
1082 ts->input->id.bustype = BUS_I2C;
1083
1084 input_set_abs_params(ts->input, ABS_MT_POSITION_X,
1085 0, le16_to_cpu(ts->info.x_max), 0, 0);
1086 input_set_abs_params(ts->input, ABS_MT_POSITION_Y,
1087 0, le16_to_cpu(ts->info.y_max), 0, 0);
1088 input_abs_set_res(ts->input, ABS_MT_POSITION_X, ts->info.x_res);
1089 input_abs_set_res(ts->input, ABS_MT_POSITION_Y, ts->info.y_res);
1090
1091 input_set_abs_params(ts->input, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
1092 input_set_abs_params(ts->input, ABS_MT_PRESSURE, 0, 255, 0, 0);
1093
1094 error = input_mt_init_slots(ts->input, RM_MAX_TOUCH_NUM,
1095 INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
1096 if (error) {
1097 dev_err(&client->dev,
1098 "failed to initialize MT slots: %d\n", error);
1099 return error;
1100 }
1101
1102 error = input_register_device(ts->input);
1103 if (error) {
1104 dev_err(&client->dev,
1105 "unable to register input device: %d\n", error);
1106 return error;
1107 }
1108
1109 error = devm_request_threaded_irq(&client->dev, client->irq,
1110 NULL, raydium_i2c_irq,
1111 IRQF_ONESHOT, client->name, ts);
1112 if (error) {
1113 dev_err(&client->dev, "Failed to register interrupt\n");
1114 return error;
1115 }
1116
1117 error = devm_device_add_group(&client->dev,
1118 &raydium_i2c_attribute_group);
1119 if (error) {
1120 dev_err(&client->dev, "failed to create sysfs attributes: %d\n",
1121 error);
1122 return error;
1123 }
1124
1125 return 0;
1126}
1127
1128static void __maybe_unused raydium_enter_sleep(struct i2c_client *client)
1129{
1130 static const u8 sleep_cmd[] = { 0x5A, 0xff, 0x00, 0x0f };
1131 int error;
1132
1133 error = raydium_i2c_send(client, RM_CMD_ENTER_SLEEP,
1134 sleep_cmd, sizeof(sleep_cmd));
1135 if (error)
1136 dev_err(&client->dev,
1137 "sleep command failed: %d\n", error);
1138}
1139
1140static int __maybe_unused raydium_i2c_suspend(struct device *dev)
1141{
1142 struct i2c_client *client = to_i2c_client(dev);
1143 struct raydium_data *ts = i2c_get_clientdata(client);
1144
1145 /* Sleep is not available in BLDR recovery mode */
1146 if (ts->boot_mode != RAYDIUM_TS_MAIN)
1147 return -EBUSY;
1148
1149 disable_irq(client->irq);
1150
1151 if (device_may_wakeup(dev)) {
1152 raydium_enter_sleep(client);
1153
1154 ts->wake_irq_enabled = (enable_irq_wake(client->irq) == 0);
1155 } else {
1156 raydium_i2c_power_off(ts);
1157 }
1158
1159 return 0;
1160}
1161
1162static int __maybe_unused raydium_i2c_resume(struct device *dev)
1163{
1164 struct i2c_client *client = to_i2c_client(dev);
1165 struct raydium_data *ts = i2c_get_clientdata(client);
1166
1167 if (device_may_wakeup(dev)) {
1168 if (ts->wake_irq_enabled)
1169 disable_irq_wake(client->irq);
1170 raydium_i2c_sw_reset(client);
1171 } else {
1172 raydium_i2c_power_on(ts);
1173 raydium_i2c_initialize(ts);
1174 }
1175
1176 enable_irq(client->irq);
1177
1178 return 0;
1179}
1180
1181static SIMPLE_DEV_PM_OPS(raydium_i2c_pm_ops,
1182 raydium_i2c_suspend, raydium_i2c_resume);
1183
1184static const struct i2c_device_id raydium_i2c_id[] = {
1185 { "raydium_i2c" , 0 },
1186 { "rm32380", 0 },
1187 { /* sentinel */ }
1188};
1189MODULE_DEVICE_TABLE(i2c, raydium_i2c_id);
1190
1191#ifdef CONFIG_ACPI
1192static const struct acpi_device_id raydium_acpi_id[] = {
1193 { "RAYD0001", 0 },
1194 { /* sentinel */ }
1195};
1196MODULE_DEVICE_TABLE(acpi, raydium_acpi_id);
1197#endif
1198
1199#ifdef CONFIG_OF
1200static const struct of_device_id raydium_of_match[] = {
1201 { .compatible = "raydium,rm32380", },
1202 { /* sentinel */ }
1203};
1204MODULE_DEVICE_TABLE(of, raydium_of_match);
1205#endif
1206
1207static struct i2c_driver raydium_i2c_driver = {
1208 .probe = raydium_i2c_probe,
1209 .id_table = raydium_i2c_id,
1210 .driver = {
1211 .name = "raydium_ts",
1212 .pm = &raydium_i2c_pm_ops,
1213 .acpi_match_table = ACPI_PTR(raydium_acpi_id),
1214 .of_match_table = of_match_ptr(raydium_of_match),
1215 },
1216};
1217module_i2c_driver(raydium_i2c_driver);
1218
1219MODULE_AUTHOR("Raydium");
1220MODULE_DESCRIPTION("Raydium I2c Touchscreen driver");
1221MODULE_LICENSE("GPL v2");