Loading...
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Derived from many drivers using generic_serial interface,
4 * especially serial_tx3912.c by Steven J. Hill and r39xx_serial.c
5 * (was in Linux/VR tree) by Jim Pick.
6 *
7 * Copyright (C) 1999 Harald Koerfgen
8 * Copyright (C) 2000 Jim Pick <jim@jimpick.com>
9 * Copyright (C) 2001 Steven J. Hill (sjhill@realitydiluted.com)
10 * Copyright (C) 2000-2002 Toshiba Corporation
11 *
12 * Serial driver for TX3927/TX4927/TX4925/TX4938 internal SIO controller
13 */
14
15#include <linux/module.h>
16#include <linux/ioport.h>
17#include <linux/init.h>
18#include <linux/console.h>
19#include <linux/delay.h>
20#include <linux/platform_device.h>
21#include <linux/pci.h>
22#include <linux/serial_core.h>
23#include <linux/serial.h>
24#include <linux/tty.h>
25#include <linux/tty_flip.h>
26
27#include <linux/io.h>
28
29#define PASS_LIMIT 256
30
31#if !defined(CONFIG_SERIAL_TXX9_STDSERIAL)
32/* "ttyS" is used for standard serial driver */
33#define TXX9_TTY_NAME "ttyTX"
34#define TXX9_TTY_MINOR_START 196
35#define TXX9_TTY_MAJOR 204
36#else
37/* acts like standard serial driver */
38#define TXX9_TTY_NAME "ttyS"
39#define TXX9_TTY_MINOR_START 64
40#define TXX9_TTY_MAJOR TTY_MAJOR
41#endif
42
43/* flag aliases */
44#define UPF_TXX9_HAVE_CTS_LINE UPF_BUGGY_UART
45#define UPF_TXX9_USE_SCLK UPF_MAGIC_MULTIPLIER
46
47#ifdef CONFIG_PCI
48/* support for Toshiba TC86C001 SIO */
49#define ENABLE_SERIAL_TXX9_PCI
50#endif
51
52/*
53 * Number of serial ports
54 */
55#define UART_NR CONFIG_SERIAL_TXX9_NR_UARTS
56
57#define TXX9_REGION_SIZE 0x24
58
59/* TXX9 Serial Registers */
60#define TXX9_SILCR 0x00
61#define TXX9_SIDICR 0x04
62#define TXX9_SIDISR 0x08
63#define TXX9_SICISR 0x0c
64#define TXX9_SIFCR 0x10
65#define TXX9_SIFLCR 0x14
66#define TXX9_SIBGR 0x18
67#define TXX9_SITFIFO 0x1c
68#define TXX9_SIRFIFO 0x20
69
70/* SILCR : Line Control */
71#define TXX9_SILCR_SCS_MASK 0x00000060
72#define TXX9_SILCR_SCS_IMCLK 0x00000000
73#define TXX9_SILCR_SCS_IMCLK_BG 0x00000020
74#define TXX9_SILCR_SCS_SCLK 0x00000040
75#define TXX9_SILCR_SCS_SCLK_BG 0x00000060
76#define TXX9_SILCR_UEPS 0x00000010
77#define TXX9_SILCR_UPEN 0x00000008
78#define TXX9_SILCR_USBL_MASK 0x00000004
79#define TXX9_SILCR_USBL_1BIT 0x00000000
80#define TXX9_SILCR_USBL_2BIT 0x00000004
81#define TXX9_SILCR_UMODE_MASK 0x00000003
82#define TXX9_SILCR_UMODE_8BIT 0x00000000
83#define TXX9_SILCR_UMODE_7BIT 0x00000001
84
85/* SIDICR : DMA/Int. Control */
86#define TXX9_SIDICR_TDE 0x00008000
87#define TXX9_SIDICR_RDE 0x00004000
88#define TXX9_SIDICR_TIE 0x00002000
89#define TXX9_SIDICR_RIE 0x00001000
90#define TXX9_SIDICR_SPIE 0x00000800
91#define TXX9_SIDICR_CTSAC 0x00000600
92#define TXX9_SIDICR_STIE_MASK 0x0000003f
93#define TXX9_SIDICR_STIE_OERS 0x00000020
94#define TXX9_SIDICR_STIE_CTSS 0x00000010
95#define TXX9_SIDICR_STIE_RBRKD 0x00000008
96#define TXX9_SIDICR_STIE_TRDY 0x00000004
97#define TXX9_SIDICR_STIE_TXALS 0x00000002
98#define TXX9_SIDICR_STIE_UBRKD 0x00000001
99
100/* SIDISR : DMA/Int. Status */
101#define TXX9_SIDISR_UBRK 0x00008000
102#define TXX9_SIDISR_UVALID 0x00004000
103#define TXX9_SIDISR_UFER 0x00002000
104#define TXX9_SIDISR_UPER 0x00001000
105#define TXX9_SIDISR_UOER 0x00000800
106#define TXX9_SIDISR_ERI 0x00000400
107#define TXX9_SIDISR_TOUT 0x00000200
108#define TXX9_SIDISR_TDIS 0x00000100
109#define TXX9_SIDISR_RDIS 0x00000080
110#define TXX9_SIDISR_STIS 0x00000040
111#define TXX9_SIDISR_RFDN_MASK 0x0000001f
112
113/* SICISR : Change Int. Status */
114#define TXX9_SICISR_OERS 0x00000020
115#define TXX9_SICISR_CTSS 0x00000010
116#define TXX9_SICISR_RBRKD 0x00000008
117#define TXX9_SICISR_TRDY 0x00000004
118#define TXX9_SICISR_TXALS 0x00000002
119#define TXX9_SICISR_UBRKD 0x00000001
120
121/* SIFCR : FIFO Control */
122#define TXX9_SIFCR_SWRST 0x00008000
123#define TXX9_SIFCR_RDIL_MASK 0x00000180
124#define TXX9_SIFCR_RDIL_1 0x00000000
125#define TXX9_SIFCR_RDIL_4 0x00000080
126#define TXX9_SIFCR_RDIL_8 0x00000100
127#define TXX9_SIFCR_RDIL_12 0x00000180
128#define TXX9_SIFCR_RDIL_MAX 0x00000180
129#define TXX9_SIFCR_TDIL_MASK 0x00000018
130#define TXX9_SIFCR_TDIL_1 0x00000000
131#define TXX9_SIFCR_TDIL_4 0x00000001
132#define TXX9_SIFCR_TDIL_8 0x00000010
133#define TXX9_SIFCR_TDIL_MAX 0x00000010
134#define TXX9_SIFCR_TFRST 0x00000004
135#define TXX9_SIFCR_RFRST 0x00000002
136#define TXX9_SIFCR_FRSTE 0x00000001
137#define TXX9_SIO_TX_FIFO 8
138#define TXX9_SIO_RX_FIFO 16
139
140/* SIFLCR : Flow Control */
141#define TXX9_SIFLCR_RCS 0x00001000
142#define TXX9_SIFLCR_TES 0x00000800
143#define TXX9_SIFLCR_RTSSC 0x00000200
144#define TXX9_SIFLCR_RSDE 0x00000100
145#define TXX9_SIFLCR_TSDE 0x00000080
146#define TXX9_SIFLCR_RTSTL_MASK 0x0000001e
147#define TXX9_SIFLCR_RTSTL_MAX 0x0000001e
148#define TXX9_SIFLCR_TBRK 0x00000001
149
150/* SIBGR : Baudrate Control */
151#define TXX9_SIBGR_BCLK_MASK 0x00000300
152#define TXX9_SIBGR_BCLK_T0 0x00000000
153#define TXX9_SIBGR_BCLK_T2 0x00000100
154#define TXX9_SIBGR_BCLK_T4 0x00000200
155#define TXX9_SIBGR_BCLK_T6 0x00000300
156#define TXX9_SIBGR_BRD_MASK 0x000000ff
157
158static inline unsigned int sio_in(struct uart_port *up, int offset)
159{
160 switch (up->iotype) {
161 default:
162 return __raw_readl(up->membase + offset);
163 case UPIO_PORT:
164 return inl(up->iobase + offset);
165 }
166}
167
168static inline void
169sio_out(struct uart_port *up, int offset, int value)
170{
171 switch (up->iotype) {
172 default:
173 __raw_writel(value, up->membase + offset);
174 break;
175 case UPIO_PORT:
176 outl(value, up->iobase + offset);
177 break;
178 }
179}
180
181static inline void
182sio_mask(struct uart_port *up, int offset, unsigned int value)
183{
184 sio_out(up, offset, sio_in(up, offset) & ~value);
185}
186static inline void
187sio_set(struct uart_port *up, int offset, unsigned int value)
188{
189 sio_out(up, offset, sio_in(up, offset) | value);
190}
191
192static inline void
193sio_quot_set(struct uart_port *up, int quot)
194{
195 quot >>= 1;
196 if (quot < 256)
197 sio_out(up, TXX9_SIBGR, quot | TXX9_SIBGR_BCLK_T0);
198 else if (quot < (256 << 2))
199 sio_out(up, TXX9_SIBGR, (quot >> 2) | TXX9_SIBGR_BCLK_T2);
200 else if (quot < (256 << 4))
201 sio_out(up, TXX9_SIBGR, (quot >> 4) | TXX9_SIBGR_BCLK_T4);
202 else if (quot < (256 << 6))
203 sio_out(up, TXX9_SIBGR, (quot >> 6) | TXX9_SIBGR_BCLK_T6);
204 else
205 sio_out(up, TXX9_SIBGR, 0xff | TXX9_SIBGR_BCLK_T6);
206}
207
208static void serial_txx9_stop_tx(struct uart_port *up)
209{
210 sio_mask(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
211}
212
213static void serial_txx9_start_tx(struct uart_port *up)
214{
215 sio_set(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
216}
217
218static void serial_txx9_stop_rx(struct uart_port *up)
219{
220 up->read_status_mask &= ~TXX9_SIDISR_RDIS;
221}
222
223static void serial_txx9_initialize(struct uart_port *up)
224{
225 unsigned int tmout = 10000;
226
227 sio_out(up, TXX9_SIFCR, TXX9_SIFCR_SWRST);
228 /* TX4925 BUG WORKAROUND. Accessing SIOC register
229 * immediately after soft reset causes bus error. */
230 udelay(1);
231 while ((sio_in(up, TXX9_SIFCR) & TXX9_SIFCR_SWRST) && --tmout)
232 udelay(1);
233 /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
234 sio_set(up, TXX9_SIFCR,
235 TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1);
236 /* initial settings */
237 sio_out(up, TXX9_SILCR,
238 TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT |
239 ((up->flags & UPF_TXX9_USE_SCLK) ?
240 TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG));
241 sio_quot_set(up, uart_get_divisor(up, 9600));
242 sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */);
243 sio_out(up, TXX9_SIDICR, 0);
244}
245
246static inline void
247receive_chars(struct uart_port *up, unsigned int *status)
248{
249 unsigned char ch;
250 unsigned int disr = *status;
251 int max_count = 256;
252 char flag;
253 unsigned int next_ignore_status_mask;
254
255 do {
256 ch = sio_in(up, TXX9_SIRFIFO);
257 flag = TTY_NORMAL;
258 up->icount.rx++;
259
260 /* mask out RFDN_MASK bit added by previous overrun */
261 next_ignore_status_mask =
262 up->ignore_status_mask & ~TXX9_SIDISR_RFDN_MASK;
263 if (unlikely(disr & (TXX9_SIDISR_UBRK | TXX9_SIDISR_UPER |
264 TXX9_SIDISR_UFER | TXX9_SIDISR_UOER))) {
265 /*
266 * For statistics only
267 */
268 if (disr & TXX9_SIDISR_UBRK) {
269 disr &= ~(TXX9_SIDISR_UFER | TXX9_SIDISR_UPER);
270 up->icount.brk++;
271 /*
272 * We do the SysRQ and SAK checking
273 * here because otherwise the break
274 * may get masked by ignore_status_mask
275 * or read_status_mask.
276 */
277 if (uart_handle_break(up))
278 goto ignore_char;
279 } else if (disr & TXX9_SIDISR_UPER)
280 up->icount.parity++;
281 else if (disr & TXX9_SIDISR_UFER)
282 up->icount.frame++;
283 if (disr & TXX9_SIDISR_UOER) {
284 up->icount.overrun++;
285 /*
286 * The receiver read buffer still hold
287 * a char which caused overrun.
288 * Ignore next char by adding RFDN_MASK
289 * to ignore_status_mask temporarily.
290 */
291 next_ignore_status_mask |=
292 TXX9_SIDISR_RFDN_MASK;
293 }
294
295 /*
296 * Mask off conditions which should be ingored.
297 */
298 disr &= up->read_status_mask;
299
300 if (disr & TXX9_SIDISR_UBRK) {
301 flag = TTY_BREAK;
302 } else if (disr & TXX9_SIDISR_UPER)
303 flag = TTY_PARITY;
304 else if (disr & TXX9_SIDISR_UFER)
305 flag = TTY_FRAME;
306 }
307 if (uart_handle_sysrq_char(up, ch))
308 goto ignore_char;
309
310 uart_insert_char(up, disr, TXX9_SIDISR_UOER, ch, flag);
311
312 ignore_char:
313 up->ignore_status_mask = next_ignore_status_mask;
314 disr = sio_in(up, TXX9_SIDISR);
315 } while (!(disr & TXX9_SIDISR_UVALID) && (max_count-- > 0));
316
317 tty_flip_buffer_push(&up->state->port);
318
319 *status = disr;
320}
321
322static inline void transmit_chars(struct uart_port *up)
323{
324 u8 ch;
325
326 uart_port_tx_limited(up, ch, TXX9_SIO_TX_FIFO,
327 true,
328 sio_out(up, TXX9_SITFIFO, ch),
329 ({}));
330}
331
332static irqreturn_t serial_txx9_interrupt(int irq, void *dev_id)
333{
334 int pass_counter = 0;
335 struct uart_port *up = dev_id;
336 unsigned int status;
337
338 while (1) {
339 spin_lock(&up->lock);
340 status = sio_in(up, TXX9_SIDISR);
341 if (!(sio_in(up, TXX9_SIDICR) & TXX9_SIDICR_TIE))
342 status &= ~TXX9_SIDISR_TDIS;
343 if (!(status & (TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
344 TXX9_SIDISR_TOUT))) {
345 spin_unlock(&up->lock);
346 break;
347 }
348
349 if (status & TXX9_SIDISR_RDIS)
350 receive_chars(up, &status);
351 if (status & TXX9_SIDISR_TDIS)
352 transmit_chars(up);
353 /* Clear TX/RX Int. Status */
354 sio_mask(up, TXX9_SIDISR,
355 TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
356 TXX9_SIDISR_TOUT);
357 spin_unlock(&up->lock);
358
359 if (pass_counter++ > PASS_LIMIT)
360 break;
361 }
362
363 return pass_counter ? IRQ_HANDLED : IRQ_NONE;
364}
365
366static unsigned int serial_txx9_tx_empty(struct uart_port *up)
367{
368 unsigned long flags;
369 unsigned int ret;
370
371 spin_lock_irqsave(&up->lock, flags);
372 ret = (sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS) ? TIOCSER_TEMT : 0;
373 spin_unlock_irqrestore(&up->lock, flags);
374
375 return ret;
376}
377
378static unsigned int serial_txx9_get_mctrl(struct uart_port *up)
379{
380 unsigned int ret;
381
382 /* no modem control lines */
383 ret = TIOCM_CAR | TIOCM_DSR;
384 ret |= (sio_in(up, TXX9_SIFLCR) & TXX9_SIFLCR_RTSSC) ? 0 : TIOCM_RTS;
385 ret |= (sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS) ? 0 : TIOCM_CTS;
386
387 return ret;
388}
389
390static void serial_txx9_set_mctrl(struct uart_port *up, unsigned int mctrl)
391{
392
393 if (mctrl & TIOCM_RTS)
394 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
395 else
396 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
397}
398
399static void serial_txx9_break_ctl(struct uart_port *up, int break_state)
400{
401 unsigned long flags;
402
403 spin_lock_irqsave(&up->lock, flags);
404 if (break_state == -1)
405 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
406 else
407 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
408 spin_unlock_irqrestore(&up->lock, flags);
409}
410
411#if defined(CONFIG_SERIAL_TXX9_CONSOLE) || defined(CONFIG_CONSOLE_POLL)
412/*
413 * Wait for transmitter & holding register to empty
414 */
415static void wait_for_xmitr(struct uart_port *up)
416{
417 unsigned int tmout = 10000;
418
419 /* Wait up to 10ms for the character(s) to be sent. */
420 while (--tmout &&
421 !(sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS))
422 udelay(1);
423
424 /* Wait up to 1s for flow control if necessary */
425 if (up->flags & UPF_CONS_FLOW) {
426 tmout = 1000000;
427 while (--tmout &&
428 (sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS))
429 udelay(1);
430 }
431}
432#endif
433
434#ifdef CONFIG_CONSOLE_POLL
435/*
436 * Console polling routines for writing and reading from the uart while
437 * in an interrupt or debug context.
438 */
439
440static int serial_txx9_get_poll_char(struct uart_port *up)
441{
442 unsigned int ier;
443 unsigned char c;
444
445 /*
446 * First save the IER then disable the interrupts
447 */
448 ier = sio_in(up, TXX9_SIDICR);
449 sio_out(up, TXX9_SIDICR, 0);
450
451 while (sio_in(up, TXX9_SIDISR) & TXX9_SIDISR_UVALID)
452 ;
453
454 c = sio_in(up, TXX9_SIRFIFO);
455
456 /*
457 * Finally, clear RX interrupt status
458 * and restore the IER
459 */
460 sio_mask(up, TXX9_SIDISR, TXX9_SIDISR_RDIS);
461 sio_out(up, TXX9_SIDICR, ier);
462 return c;
463}
464
465
466static void serial_txx9_put_poll_char(struct uart_port *up, unsigned char c)
467{
468 unsigned int ier;
469
470 /*
471 * First save the IER then disable the interrupts
472 */
473 ier = sio_in(up, TXX9_SIDICR);
474 sio_out(up, TXX9_SIDICR, 0);
475
476 wait_for_xmitr(up);
477 /*
478 * Send the character out.
479 */
480 sio_out(up, TXX9_SITFIFO, c);
481
482 /*
483 * Finally, wait for transmitter to become empty
484 * and restore the IER
485 */
486 wait_for_xmitr(up);
487 sio_out(up, TXX9_SIDICR, ier);
488}
489
490#endif /* CONFIG_CONSOLE_POLL */
491
492static int serial_txx9_startup(struct uart_port *up)
493{
494 unsigned long flags;
495 int retval;
496
497 /*
498 * Clear the FIFO buffers and disable them.
499 * (they will be reenabled in set_termios())
500 */
501 sio_set(up, TXX9_SIFCR,
502 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
503 /* clear reset */
504 sio_mask(up, TXX9_SIFCR,
505 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
506 sio_out(up, TXX9_SIDICR, 0);
507
508 /*
509 * Clear the interrupt registers.
510 */
511 sio_out(up, TXX9_SIDISR, 0);
512
513 retval = request_irq(up->irq, serial_txx9_interrupt,
514 IRQF_SHARED, "serial_txx9", up);
515 if (retval)
516 return retval;
517
518 /*
519 * Now, initialize the UART
520 */
521 spin_lock_irqsave(&up->lock, flags);
522 serial_txx9_set_mctrl(up, up->mctrl);
523 spin_unlock_irqrestore(&up->lock, flags);
524
525 /* Enable RX/TX */
526 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
527
528 /*
529 * Finally, enable interrupts.
530 */
531 sio_set(up, TXX9_SIDICR, TXX9_SIDICR_RIE);
532
533 return 0;
534}
535
536static void serial_txx9_shutdown(struct uart_port *up)
537{
538 unsigned long flags;
539
540 /*
541 * Disable interrupts from this port
542 */
543 sio_out(up, TXX9_SIDICR, 0); /* disable all intrs */
544
545 spin_lock_irqsave(&up->lock, flags);
546 serial_txx9_set_mctrl(up, up->mctrl);
547 spin_unlock_irqrestore(&up->lock, flags);
548
549 /*
550 * Disable break condition
551 */
552 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
553
554#ifdef CONFIG_SERIAL_TXX9_CONSOLE
555 if (up->cons && up->line == up->cons->index) {
556 free_irq(up->irq, up);
557 return;
558 }
559#endif
560 /* reset FIFOs */
561 sio_set(up, TXX9_SIFCR,
562 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
563 /* clear reset */
564 sio_mask(up, TXX9_SIFCR,
565 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
566
567 /* Disable RX/TX */
568 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
569
570 free_irq(up->irq, up);
571}
572
573static void
574serial_txx9_set_termios(struct uart_port *up, struct ktermios *termios,
575 const struct ktermios *old)
576{
577 unsigned int cval, fcr = 0;
578 unsigned long flags;
579 unsigned int baud, quot;
580
581 /*
582 * We don't support modem control lines.
583 */
584 termios->c_cflag &= ~(HUPCL | CMSPAR);
585 termios->c_cflag |= CLOCAL;
586
587 cval = sio_in(up, TXX9_SILCR);
588 /* byte size and parity */
589 cval &= ~TXX9_SILCR_UMODE_MASK;
590 switch (termios->c_cflag & CSIZE) {
591 case CS7:
592 cval |= TXX9_SILCR_UMODE_7BIT;
593 break;
594 default:
595 case CS5: /* not supported */
596 case CS6: /* not supported */
597 case CS8:
598 cval |= TXX9_SILCR_UMODE_8BIT;
599 termios->c_cflag &= ~CSIZE;
600 termios->c_cflag |= CS8;
601 break;
602 }
603
604 cval &= ~TXX9_SILCR_USBL_MASK;
605 if (termios->c_cflag & CSTOPB)
606 cval |= TXX9_SILCR_USBL_2BIT;
607 else
608 cval |= TXX9_SILCR_USBL_1BIT;
609 cval &= ~(TXX9_SILCR_UPEN | TXX9_SILCR_UEPS);
610 if (termios->c_cflag & PARENB)
611 cval |= TXX9_SILCR_UPEN;
612 if (!(termios->c_cflag & PARODD))
613 cval |= TXX9_SILCR_UEPS;
614
615 /*
616 * Ask the core to calculate the divisor for us.
617 */
618 baud = uart_get_baud_rate(up, termios, old, 0, up->uartclk/16/2);
619 quot = uart_get_divisor(up, baud);
620
621 /* Set up FIFOs */
622 /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
623 fcr = TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1;
624
625 /*
626 * Ok, we're now changing the port state. Do it with
627 * interrupts disabled.
628 */
629 spin_lock_irqsave(&up->lock, flags);
630
631 /*
632 * Update the per-port timeout.
633 */
634 uart_update_timeout(up, termios->c_cflag, baud);
635
636 up->read_status_mask = TXX9_SIDISR_UOER |
637 TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS;
638 if (termios->c_iflag & INPCK)
639 up->read_status_mask |= TXX9_SIDISR_UFER | TXX9_SIDISR_UPER;
640 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
641 up->read_status_mask |= TXX9_SIDISR_UBRK;
642
643 /*
644 * Characteres to ignore
645 */
646 up->ignore_status_mask = 0;
647 if (termios->c_iflag & IGNPAR)
648 up->ignore_status_mask |= TXX9_SIDISR_UPER | TXX9_SIDISR_UFER;
649 if (termios->c_iflag & IGNBRK) {
650 up->ignore_status_mask |= TXX9_SIDISR_UBRK;
651 /*
652 * If we're ignoring parity and break indicators,
653 * ignore overruns too (for real raw support).
654 */
655 if (termios->c_iflag & IGNPAR)
656 up->ignore_status_mask |= TXX9_SIDISR_UOER;
657 }
658
659 /*
660 * ignore all characters if CREAD is not set
661 */
662 if ((termios->c_cflag & CREAD) == 0)
663 up->ignore_status_mask |= TXX9_SIDISR_RDIS;
664
665 /* CTS flow control flag */
666 if ((termios->c_cflag & CRTSCTS) &&
667 (up->flags & UPF_TXX9_HAVE_CTS_LINE)) {
668 sio_set(up, TXX9_SIFLCR,
669 TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
670 } else {
671 sio_mask(up, TXX9_SIFLCR,
672 TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
673 }
674
675 sio_out(up, TXX9_SILCR, cval);
676 sio_quot_set(up, quot);
677 sio_out(up, TXX9_SIFCR, fcr);
678
679 serial_txx9_set_mctrl(up, up->mctrl);
680 spin_unlock_irqrestore(&up->lock, flags);
681}
682
683static void
684serial_txx9_pm(struct uart_port *port, unsigned int state,
685 unsigned int oldstate)
686{
687 /*
688 * If oldstate was -1 this is called from
689 * uart_configure_port(). In this case do not initialize the
690 * port now, because the port was already initialized (for
691 * non-console port) or should not be initialized here (for
692 * console port). If we initialized the port here we lose
693 * serial console settings.
694 */
695 if (state == 0 && oldstate != -1)
696 serial_txx9_initialize(port);
697}
698
699static int serial_txx9_request_resource(struct uart_port *up)
700{
701 unsigned int size = TXX9_REGION_SIZE;
702 int ret = 0;
703
704 switch (up->iotype) {
705 default:
706 if (!up->mapbase)
707 break;
708
709 if (!request_mem_region(up->mapbase, size, "serial_txx9")) {
710 ret = -EBUSY;
711 break;
712 }
713
714 if (up->flags & UPF_IOREMAP) {
715 up->membase = ioremap(up->mapbase, size);
716 if (!up->membase) {
717 release_mem_region(up->mapbase, size);
718 ret = -ENOMEM;
719 }
720 }
721 break;
722
723 case UPIO_PORT:
724 if (!request_region(up->iobase, size, "serial_txx9"))
725 ret = -EBUSY;
726 break;
727 }
728 return ret;
729}
730
731static void serial_txx9_release_resource(struct uart_port *up)
732{
733 unsigned int size = TXX9_REGION_SIZE;
734
735 switch (up->iotype) {
736 default:
737 if (!up->mapbase)
738 break;
739
740 if (up->flags & UPF_IOREMAP) {
741 iounmap(up->membase);
742 up->membase = NULL;
743 }
744
745 release_mem_region(up->mapbase, size);
746 break;
747
748 case UPIO_PORT:
749 release_region(up->iobase, size);
750 break;
751 }
752}
753
754static void serial_txx9_release_port(struct uart_port *up)
755{
756 serial_txx9_release_resource(up);
757}
758
759static int serial_txx9_request_port(struct uart_port *up)
760{
761 return serial_txx9_request_resource(up);
762}
763
764static void serial_txx9_config_port(struct uart_port *up, int uflags)
765{
766 int ret;
767
768 /*
769 * Find the region that we can probe for. This in turn
770 * tells us whether we can probe for the type of port.
771 */
772 ret = serial_txx9_request_resource(up);
773 if (ret < 0)
774 return;
775 up->type = PORT_TXX9;
776 up->fifosize = TXX9_SIO_TX_FIFO;
777
778#ifdef CONFIG_SERIAL_TXX9_CONSOLE
779 if (up->line == up->cons->index)
780 return;
781#endif
782 serial_txx9_initialize(up);
783}
784
785static const char *
786serial_txx9_type(struct uart_port *port)
787{
788 return "txx9";
789}
790
791static const struct uart_ops serial_txx9_pops = {
792 .tx_empty = serial_txx9_tx_empty,
793 .set_mctrl = serial_txx9_set_mctrl,
794 .get_mctrl = serial_txx9_get_mctrl,
795 .stop_tx = serial_txx9_stop_tx,
796 .start_tx = serial_txx9_start_tx,
797 .stop_rx = serial_txx9_stop_rx,
798 .break_ctl = serial_txx9_break_ctl,
799 .startup = serial_txx9_startup,
800 .shutdown = serial_txx9_shutdown,
801 .set_termios = serial_txx9_set_termios,
802 .pm = serial_txx9_pm,
803 .type = serial_txx9_type,
804 .release_port = serial_txx9_release_port,
805 .request_port = serial_txx9_request_port,
806 .config_port = serial_txx9_config_port,
807#ifdef CONFIG_CONSOLE_POLL
808 .poll_get_char = serial_txx9_get_poll_char,
809 .poll_put_char = serial_txx9_put_poll_char,
810#endif
811};
812
813static struct uart_port serial_txx9_ports[UART_NR];
814
815static void __init serial_txx9_register_ports(struct uart_driver *drv,
816 struct device *dev)
817{
818 int i;
819
820 for (i = 0; i < UART_NR; i++) {
821 struct uart_port *up = &serial_txx9_ports[i];
822
823 up->line = i;
824 up->ops = &serial_txx9_pops;
825 up->dev = dev;
826 if (up->iobase || up->mapbase)
827 uart_add_one_port(drv, up);
828 }
829}
830
831#ifdef CONFIG_SERIAL_TXX9_CONSOLE
832
833static void serial_txx9_console_putchar(struct uart_port *up, unsigned char ch)
834{
835 wait_for_xmitr(up);
836 sio_out(up, TXX9_SITFIFO, ch);
837}
838
839/*
840 * Print a string to the serial port trying not to disturb
841 * any possible real use of the port...
842 *
843 * The console_lock must be held when we get here.
844 */
845static void
846serial_txx9_console_write(struct console *co, const char *s, unsigned int count)
847{
848 struct uart_port *up = &serial_txx9_ports[co->index];
849 unsigned int ier, flcr;
850
851 /*
852 * First save the UER then disable the interrupts
853 */
854 ier = sio_in(up, TXX9_SIDICR);
855 sio_out(up, TXX9_SIDICR, 0);
856 /*
857 * Disable flow-control if enabled (and unnecessary)
858 */
859 flcr = sio_in(up, TXX9_SIFLCR);
860 if (!(up->flags & UPF_CONS_FLOW) && (flcr & TXX9_SIFLCR_TES))
861 sio_out(up, TXX9_SIFLCR, flcr & ~TXX9_SIFLCR_TES);
862
863 uart_console_write(up, s, count, serial_txx9_console_putchar);
864
865 /*
866 * Finally, wait for transmitter to become empty
867 * and restore the IER
868 */
869 wait_for_xmitr(up);
870 sio_out(up, TXX9_SIFLCR, flcr);
871 sio_out(up, TXX9_SIDICR, ier);
872}
873
874static int __init serial_txx9_console_setup(struct console *co, char *options)
875{
876 struct uart_port *up;
877 int baud = 9600;
878 int bits = 8;
879 int parity = 'n';
880 int flow = 'n';
881
882 /*
883 * Check whether an invalid uart number has been specified, and
884 * if so, search for the first available port that does have
885 * console support.
886 */
887 if (co->index >= UART_NR)
888 co->index = 0;
889 up = &serial_txx9_ports[co->index];
890 if (!up->ops)
891 return -ENODEV;
892
893 serial_txx9_initialize(up);
894
895 if (options)
896 uart_parse_options(options, &baud, &parity, &bits, &flow);
897
898 return uart_set_options(up, co, baud, parity, bits, flow);
899}
900
901static struct uart_driver serial_txx9_reg;
902static struct console serial_txx9_console = {
903 .name = TXX9_TTY_NAME,
904 .write = serial_txx9_console_write,
905 .device = uart_console_device,
906 .setup = serial_txx9_console_setup,
907 .flags = CON_PRINTBUFFER,
908 .index = -1,
909 .data = &serial_txx9_reg,
910};
911
912static int __init serial_txx9_console_init(void)
913{
914 register_console(&serial_txx9_console);
915 return 0;
916}
917console_initcall(serial_txx9_console_init);
918
919#define SERIAL_TXX9_CONSOLE &serial_txx9_console
920#else
921#define SERIAL_TXX9_CONSOLE NULL
922#endif
923
924static struct uart_driver serial_txx9_reg = {
925 .owner = THIS_MODULE,
926 .driver_name = "serial_txx9",
927 .dev_name = TXX9_TTY_NAME,
928 .major = TXX9_TTY_MAJOR,
929 .minor = TXX9_TTY_MINOR_START,
930 .nr = UART_NR,
931 .cons = SERIAL_TXX9_CONSOLE,
932};
933
934int __init early_serial_txx9_setup(struct uart_port *port)
935{
936 if (port->line >= ARRAY_SIZE(serial_txx9_ports))
937 return -ENODEV;
938
939 serial_txx9_ports[port->line] = *port;
940 serial_txx9_ports[port->line].ops = &serial_txx9_pops;
941 serial_txx9_ports[port->line].flags |=
942 UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
943 return 0;
944}
945
946static DEFINE_MUTEX(serial_txx9_mutex);
947
948/**
949 * serial_txx9_register_port - register a serial port
950 * @port: serial port template
951 *
952 * Configure the serial port specified by the request.
953 *
954 * The port is then probed and if necessary the IRQ is autodetected
955 * If this fails an error is returned.
956 *
957 * On success the port is ready to use and the line number is returned.
958 */
959static int serial_txx9_register_port(struct uart_port *port)
960{
961 int i;
962 struct uart_port *uart;
963 int ret = -ENOSPC;
964
965 mutex_lock(&serial_txx9_mutex);
966 for (i = 0; i < UART_NR; i++) {
967 uart = &serial_txx9_ports[i];
968 if (uart_match_port(uart, port)) {
969 uart_remove_one_port(&serial_txx9_reg, uart);
970 break;
971 }
972 }
973 if (i == UART_NR) {
974 /* Find unused port */
975 for (i = 0; i < UART_NR; i++) {
976 uart = &serial_txx9_ports[i];
977 if (!(uart->iobase || uart->mapbase))
978 break;
979 }
980 }
981 if (i < UART_NR) {
982 uart->iobase = port->iobase;
983 uart->membase = port->membase;
984 uart->irq = port->irq;
985 uart->uartclk = port->uartclk;
986 uart->iotype = port->iotype;
987 uart->flags = port->flags
988 | UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
989 uart->mapbase = port->mapbase;
990 if (port->dev)
991 uart->dev = port->dev;
992 ret = uart_add_one_port(&serial_txx9_reg, uart);
993 if (ret == 0)
994 ret = uart->line;
995 }
996 mutex_unlock(&serial_txx9_mutex);
997 return ret;
998}
999
1000/**
1001 * serial_txx9_unregister_port - remove a txx9 serial port at runtime
1002 * @line: serial line number
1003 *
1004 * Remove one serial port. This may not be called from interrupt
1005 * context. We hand the port back to the our control.
1006 */
1007static void serial_txx9_unregister_port(int line)
1008{
1009 struct uart_port *uart = &serial_txx9_ports[line];
1010
1011 mutex_lock(&serial_txx9_mutex);
1012 uart_remove_one_port(&serial_txx9_reg, uart);
1013 uart->flags = 0;
1014 uart->type = PORT_UNKNOWN;
1015 uart->iobase = 0;
1016 uart->mapbase = 0;
1017 uart->membase = NULL;
1018 uart->dev = NULL;
1019 mutex_unlock(&serial_txx9_mutex);
1020}
1021
1022/*
1023 * Register a set of serial devices attached to a platform device.
1024 */
1025static int serial_txx9_probe(struct platform_device *dev)
1026{
1027 struct uart_port *p = dev_get_platdata(&dev->dev);
1028 struct uart_port port;
1029 int ret, i;
1030
1031 memset(&port, 0, sizeof(struct uart_port));
1032 for (i = 0; p && p->uartclk != 0; p++, i++) {
1033 port.iobase = p->iobase;
1034 port.membase = p->membase;
1035 port.irq = p->irq;
1036 port.uartclk = p->uartclk;
1037 port.iotype = p->iotype;
1038 port.flags = p->flags;
1039 port.mapbase = p->mapbase;
1040 port.dev = &dev->dev;
1041 port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_TXX9_CONSOLE);
1042 ret = serial_txx9_register_port(&port);
1043 if (ret < 0) {
1044 dev_err(&dev->dev, "unable to register port at index %d "
1045 "(IO%lx MEM%llx IRQ%d): %d\n", i,
1046 p->iobase, (unsigned long long)p->mapbase,
1047 p->irq, ret);
1048 }
1049 }
1050 return 0;
1051}
1052
1053/*
1054 * Remove serial ports registered against a platform device.
1055 */
1056static int serial_txx9_remove(struct platform_device *dev)
1057{
1058 int i;
1059
1060 for (i = 0; i < UART_NR; i++) {
1061 struct uart_port *up = &serial_txx9_ports[i];
1062
1063 if (up->dev == &dev->dev)
1064 serial_txx9_unregister_port(i);
1065 }
1066 return 0;
1067}
1068
1069#ifdef CONFIG_PM
1070static int serial_txx9_suspend(struct platform_device *dev, pm_message_t state)
1071{
1072 int i;
1073
1074 for (i = 0; i < UART_NR; i++) {
1075 struct uart_port *up = &serial_txx9_ports[i];
1076
1077 if (up->type != PORT_UNKNOWN && up->dev == &dev->dev)
1078 uart_suspend_port(&serial_txx9_reg, up);
1079 }
1080
1081 return 0;
1082}
1083
1084static int serial_txx9_resume(struct platform_device *dev)
1085{
1086 int i;
1087
1088 for (i = 0; i < UART_NR; i++) {
1089 struct uart_port *up = &serial_txx9_ports[i];
1090
1091 if (up->type != PORT_UNKNOWN && up->dev == &dev->dev)
1092 uart_resume_port(&serial_txx9_reg, up);
1093 }
1094
1095 return 0;
1096}
1097#endif
1098
1099static struct platform_driver serial_txx9_plat_driver = {
1100 .probe = serial_txx9_probe,
1101 .remove = serial_txx9_remove,
1102#ifdef CONFIG_PM
1103 .suspend = serial_txx9_suspend,
1104 .resume = serial_txx9_resume,
1105#endif
1106 .driver = {
1107 .name = "serial_txx9",
1108 },
1109};
1110
1111#ifdef ENABLE_SERIAL_TXX9_PCI
1112/*
1113 * Probe one serial board. Unfortunately, there is no rhyme nor reason
1114 * to the arrangement of serial ports on a PCI card.
1115 */
1116static int
1117pciserial_txx9_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
1118{
1119 struct uart_port port;
1120 int line;
1121 int rc;
1122
1123 rc = pci_enable_device(dev);
1124 if (rc)
1125 return rc;
1126
1127 memset(&port, 0, sizeof(port));
1128 port.ops = &serial_txx9_pops;
1129 port.flags |= UPF_TXX9_HAVE_CTS_LINE;
1130 port.uartclk = 66670000;
1131 port.irq = dev->irq;
1132 port.iotype = UPIO_PORT;
1133 port.iobase = pci_resource_start(dev, 1);
1134 port.dev = &dev->dev;
1135 line = serial_txx9_register_port(&port);
1136 if (line < 0) {
1137 printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), line);
1138 pci_disable_device(dev);
1139 return line;
1140 }
1141 pci_set_drvdata(dev, &serial_txx9_ports[line]);
1142
1143 return 0;
1144}
1145
1146static void pciserial_txx9_remove_one(struct pci_dev *dev)
1147{
1148 struct uart_port *up = pci_get_drvdata(dev);
1149
1150 if (up) {
1151 serial_txx9_unregister_port(up->line);
1152 pci_disable_device(dev);
1153 }
1154}
1155
1156#ifdef CONFIG_PM
1157static int pciserial_txx9_suspend_one(struct pci_dev *dev, pm_message_t state)
1158{
1159 struct uart_port *up = pci_get_drvdata(dev);
1160
1161 if (up)
1162 uart_suspend_port(&serial_txx9_reg, up);
1163 pci_save_state(dev);
1164 pci_set_power_state(dev, pci_choose_state(dev, state));
1165 return 0;
1166}
1167
1168static int pciserial_txx9_resume_one(struct pci_dev *dev)
1169{
1170 struct uart_port *up = pci_get_drvdata(dev);
1171
1172 pci_set_power_state(dev, PCI_D0);
1173 pci_restore_state(dev);
1174 if (up)
1175 uart_resume_port(&serial_txx9_reg, up);
1176 return 0;
1177}
1178#endif
1179
1180static const struct pci_device_id serial_txx9_pci_tbl[] = {
1181 { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_TC86C001_MISC) },
1182 { 0, }
1183};
1184
1185static struct pci_driver serial_txx9_pci_driver = {
1186 .name = "serial_txx9",
1187 .probe = pciserial_txx9_init_one,
1188 .remove = pciserial_txx9_remove_one,
1189#ifdef CONFIG_PM
1190 .suspend = pciserial_txx9_suspend_one,
1191 .resume = pciserial_txx9_resume_one,
1192#endif
1193 .id_table = serial_txx9_pci_tbl,
1194};
1195
1196MODULE_DEVICE_TABLE(pci, serial_txx9_pci_tbl);
1197#endif /* ENABLE_SERIAL_TXX9_PCI */
1198
1199static struct platform_device *serial_txx9_plat_devs;
1200
1201static int __init serial_txx9_init(void)
1202{
1203 int ret;
1204
1205 ret = uart_register_driver(&serial_txx9_reg);
1206 if (ret)
1207 goto out;
1208
1209 serial_txx9_plat_devs = platform_device_alloc("serial_txx9", -1);
1210 if (!serial_txx9_plat_devs) {
1211 ret = -ENOMEM;
1212 goto unreg_uart_drv;
1213 }
1214
1215 ret = platform_device_add(serial_txx9_plat_devs);
1216 if (ret)
1217 goto put_dev;
1218
1219 serial_txx9_register_ports(&serial_txx9_reg,
1220 &serial_txx9_plat_devs->dev);
1221
1222 ret = platform_driver_register(&serial_txx9_plat_driver);
1223 if (ret)
1224 goto del_dev;
1225
1226#ifdef ENABLE_SERIAL_TXX9_PCI
1227 ret = pci_register_driver(&serial_txx9_pci_driver);
1228 if (ret) {
1229 platform_driver_unregister(&serial_txx9_plat_driver);
1230 }
1231#endif
1232 if (ret == 0)
1233 goto out;
1234
1235 del_dev:
1236 platform_device_del(serial_txx9_plat_devs);
1237 put_dev:
1238 platform_device_put(serial_txx9_plat_devs);
1239 unreg_uart_drv:
1240 uart_unregister_driver(&serial_txx9_reg);
1241 out:
1242 return ret;
1243}
1244
1245static void __exit serial_txx9_exit(void)
1246{
1247 int i;
1248
1249#ifdef ENABLE_SERIAL_TXX9_PCI
1250 pci_unregister_driver(&serial_txx9_pci_driver);
1251#endif
1252 platform_driver_unregister(&serial_txx9_plat_driver);
1253 platform_device_unregister(serial_txx9_plat_devs);
1254 for (i = 0; i < UART_NR; i++) {
1255 struct uart_port *up = &serial_txx9_ports[i];
1256 if (up->iobase || up->mapbase)
1257 uart_remove_one_port(&serial_txx9_reg, up);
1258 }
1259
1260 uart_unregister_driver(&serial_txx9_reg);
1261}
1262
1263module_init(serial_txx9_init);
1264module_exit(serial_txx9_exit);
1265
1266MODULE_LICENSE("GPL");
1267MODULE_DESCRIPTION("TX39/49 serial driver");
1268
1269MODULE_ALIAS_CHARDEV_MAJOR(TXX9_TTY_MAJOR);
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Derived from many drivers using generic_serial interface,
4 * especially serial_tx3912.c by Steven J. Hill and r39xx_serial.c
5 * (was in Linux/VR tree) by Jim Pick.
6 *
7 * Copyright (C) 1999 Harald Koerfgen
8 * Copyright (C) 2000 Jim Pick <jim@jimpick.com>
9 * Copyright (C) 2001 Steven J. Hill (sjhill@realitydiluted.com)
10 * Copyright (C) 2000-2002 Toshiba Corporation
11 *
12 * Serial driver for TX3927/TX4927/TX4925/TX4938 internal SIO controller
13 */
14
15#include <linux/module.h>
16#include <linux/ioport.h>
17#include <linux/init.h>
18#include <linux/console.h>
19#include <linux/delay.h>
20#include <linux/platform_device.h>
21#include <linux/pci.h>
22#include <linux/serial_core.h>
23#include <linux/serial.h>
24#include <linux/tty.h>
25#include <linux/tty_flip.h>
26
27#include <asm/io.h>
28
29static char *serial_version = "1.11";
30static char *serial_name = "TX39/49 Serial driver";
31
32#define PASS_LIMIT 256
33
34#if !defined(CONFIG_SERIAL_TXX9_STDSERIAL)
35/* "ttyS" is used for standard serial driver */
36#define TXX9_TTY_NAME "ttyTX"
37#define TXX9_TTY_MINOR_START 196
38#define TXX9_TTY_MAJOR 204
39#else
40/* acts like standard serial driver */
41#define TXX9_TTY_NAME "ttyS"
42#define TXX9_TTY_MINOR_START 64
43#define TXX9_TTY_MAJOR TTY_MAJOR
44#endif
45
46/* flag aliases */
47#define UPF_TXX9_HAVE_CTS_LINE UPF_BUGGY_UART
48#define UPF_TXX9_USE_SCLK UPF_MAGIC_MULTIPLIER
49
50#ifdef CONFIG_PCI
51/* support for Toshiba TC86C001 SIO */
52#define ENABLE_SERIAL_TXX9_PCI
53#endif
54
55/*
56 * Number of serial ports
57 */
58#define UART_NR CONFIG_SERIAL_TXX9_NR_UARTS
59
60struct uart_txx9_port {
61 struct uart_port port;
62 /* No additional info for now */
63};
64
65#define TXX9_REGION_SIZE 0x24
66
67/* TXX9 Serial Registers */
68#define TXX9_SILCR 0x00
69#define TXX9_SIDICR 0x04
70#define TXX9_SIDISR 0x08
71#define TXX9_SICISR 0x0c
72#define TXX9_SIFCR 0x10
73#define TXX9_SIFLCR 0x14
74#define TXX9_SIBGR 0x18
75#define TXX9_SITFIFO 0x1c
76#define TXX9_SIRFIFO 0x20
77
78/* SILCR : Line Control */
79#define TXX9_SILCR_SCS_MASK 0x00000060
80#define TXX9_SILCR_SCS_IMCLK 0x00000000
81#define TXX9_SILCR_SCS_IMCLK_BG 0x00000020
82#define TXX9_SILCR_SCS_SCLK 0x00000040
83#define TXX9_SILCR_SCS_SCLK_BG 0x00000060
84#define TXX9_SILCR_UEPS 0x00000010
85#define TXX9_SILCR_UPEN 0x00000008
86#define TXX9_SILCR_USBL_MASK 0x00000004
87#define TXX9_SILCR_USBL_1BIT 0x00000000
88#define TXX9_SILCR_USBL_2BIT 0x00000004
89#define TXX9_SILCR_UMODE_MASK 0x00000003
90#define TXX9_SILCR_UMODE_8BIT 0x00000000
91#define TXX9_SILCR_UMODE_7BIT 0x00000001
92
93/* SIDICR : DMA/Int. Control */
94#define TXX9_SIDICR_TDE 0x00008000
95#define TXX9_SIDICR_RDE 0x00004000
96#define TXX9_SIDICR_TIE 0x00002000
97#define TXX9_SIDICR_RIE 0x00001000
98#define TXX9_SIDICR_SPIE 0x00000800
99#define TXX9_SIDICR_CTSAC 0x00000600
100#define TXX9_SIDICR_STIE_MASK 0x0000003f
101#define TXX9_SIDICR_STIE_OERS 0x00000020
102#define TXX9_SIDICR_STIE_CTSS 0x00000010
103#define TXX9_SIDICR_STIE_RBRKD 0x00000008
104#define TXX9_SIDICR_STIE_TRDY 0x00000004
105#define TXX9_SIDICR_STIE_TXALS 0x00000002
106#define TXX9_SIDICR_STIE_UBRKD 0x00000001
107
108/* SIDISR : DMA/Int. Status */
109#define TXX9_SIDISR_UBRK 0x00008000
110#define TXX9_SIDISR_UVALID 0x00004000
111#define TXX9_SIDISR_UFER 0x00002000
112#define TXX9_SIDISR_UPER 0x00001000
113#define TXX9_SIDISR_UOER 0x00000800
114#define TXX9_SIDISR_ERI 0x00000400
115#define TXX9_SIDISR_TOUT 0x00000200
116#define TXX9_SIDISR_TDIS 0x00000100
117#define TXX9_SIDISR_RDIS 0x00000080
118#define TXX9_SIDISR_STIS 0x00000040
119#define TXX9_SIDISR_RFDN_MASK 0x0000001f
120
121/* SICISR : Change Int. Status */
122#define TXX9_SICISR_OERS 0x00000020
123#define TXX9_SICISR_CTSS 0x00000010
124#define TXX9_SICISR_RBRKD 0x00000008
125#define TXX9_SICISR_TRDY 0x00000004
126#define TXX9_SICISR_TXALS 0x00000002
127#define TXX9_SICISR_UBRKD 0x00000001
128
129/* SIFCR : FIFO Control */
130#define TXX9_SIFCR_SWRST 0x00008000
131#define TXX9_SIFCR_RDIL_MASK 0x00000180
132#define TXX9_SIFCR_RDIL_1 0x00000000
133#define TXX9_SIFCR_RDIL_4 0x00000080
134#define TXX9_SIFCR_RDIL_8 0x00000100
135#define TXX9_SIFCR_RDIL_12 0x00000180
136#define TXX9_SIFCR_RDIL_MAX 0x00000180
137#define TXX9_SIFCR_TDIL_MASK 0x00000018
138#define TXX9_SIFCR_TDIL_1 0x00000000
139#define TXX9_SIFCR_TDIL_4 0x00000001
140#define TXX9_SIFCR_TDIL_8 0x00000010
141#define TXX9_SIFCR_TDIL_MAX 0x00000010
142#define TXX9_SIFCR_TFRST 0x00000004
143#define TXX9_SIFCR_RFRST 0x00000002
144#define TXX9_SIFCR_FRSTE 0x00000001
145#define TXX9_SIO_TX_FIFO 8
146#define TXX9_SIO_RX_FIFO 16
147
148/* SIFLCR : Flow Control */
149#define TXX9_SIFLCR_RCS 0x00001000
150#define TXX9_SIFLCR_TES 0x00000800
151#define TXX9_SIFLCR_RTSSC 0x00000200
152#define TXX9_SIFLCR_RSDE 0x00000100
153#define TXX9_SIFLCR_TSDE 0x00000080
154#define TXX9_SIFLCR_RTSTL_MASK 0x0000001e
155#define TXX9_SIFLCR_RTSTL_MAX 0x0000001e
156#define TXX9_SIFLCR_TBRK 0x00000001
157
158/* SIBGR : Baudrate Control */
159#define TXX9_SIBGR_BCLK_MASK 0x00000300
160#define TXX9_SIBGR_BCLK_T0 0x00000000
161#define TXX9_SIBGR_BCLK_T2 0x00000100
162#define TXX9_SIBGR_BCLK_T4 0x00000200
163#define TXX9_SIBGR_BCLK_T6 0x00000300
164#define TXX9_SIBGR_BRD_MASK 0x000000ff
165
166static inline unsigned int sio_in(struct uart_txx9_port *up, int offset)
167{
168 switch (up->port.iotype) {
169 default:
170 return __raw_readl(up->port.membase + offset);
171 case UPIO_PORT:
172 return inl(up->port.iobase + offset);
173 }
174}
175
176static inline void
177sio_out(struct uart_txx9_port *up, int offset, int value)
178{
179 switch (up->port.iotype) {
180 default:
181 __raw_writel(value, up->port.membase + offset);
182 break;
183 case UPIO_PORT:
184 outl(value, up->port.iobase + offset);
185 break;
186 }
187}
188
189static inline void
190sio_mask(struct uart_txx9_port *up, int offset, unsigned int value)
191{
192 sio_out(up, offset, sio_in(up, offset) & ~value);
193}
194static inline void
195sio_set(struct uart_txx9_port *up, int offset, unsigned int value)
196{
197 sio_out(up, offset, sio_in(up, offset) | value);
198}
199
200static inline void
201sio_quot_set(struct uart_txx9_port *up, int quot)
202{
203 quot >>= 1;
204 if (quot < 256)
205 sio_out(up, TXX9_SIBGR, quot | TXX9_SIBGR_BCLK_T0);
206 else if (quot < (256 << 2))
207 sio_out(up, TXX9_SIBGR, (quot >> 2) | TXX9_SIBGR_BCLK_T2);
208 else if (quot < (256 << 4))
209 sio_out(up, TXX9_SIBGR, (quot >> 4) | TXX9_SIBGR_BCLK_T4);
210 else if (quot < (256 << 6))
211 sio_out(up, TXX9_SIBGR, (quot >> 6) | TXX9_SIBGR_BCLK_T6);
212 else
213 sio_out(up, TXX9_SIBGR, 0xff | TXX9_SIBGR_BCLK_T6);
214}
215
216static struct uart_txx9_port *to_uart_txx9_port(struct uart_port *port)
217{
218 return container_of(port, struct uart_txx9_port, port);
219}
220
221static void serial_txx9_stop_tx(struct uart_port *port)
222{
223 struct uart_txx9_port *up = to_uart_txx9_port(port);
224 sio_mask(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
225}
226
227static void serial_txx9_start_tx(struct uart_port *port)
228{
229 struct uart_txx9_port *up = to_uart_txx9_port(port);
230 sio_set(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
231}
232
233static void serial_txx9_stop_rx(struct uart_port *port)
234{
235 struct uart_txx9_port *up = to_uart_txx9_port(port);
236 up->port.read_status_mask &= ~TXX9_SIDISR_RDIS;
237}
238
239static void serial_txx9_initialize(struct uart_port *port)
240{
241 struct uart_txx9_port *up = to_uart_txx9_port(port);
242 unsigned int tmout = 10000;
243
244 sio_out(up, TXX9_SIFCR, TXX9_SIFCR_SWRST);
245 /* TX4925 BUG WORKAROUND. Accessing SIOC register
246 * immediately after soft reset causes bus error. */
247 udelay(1);
248 while ((sio_in(up, TXX9_SIFCR) & TXX9_SIFCR_SWRST) && --tmout)
249 udelay(1);
250 /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
251 sio_set(up, TXX9_SIFCR,
252 TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1);
253 /* initial settings */
254 sio_out(up, TXX9_SILCR,
255 TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT |
256 ((up->port.flags & UPF_TXX9_USE_SCLK) ?
257 TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG));
258 sio_quot_set(up, uart_get_divisor(port, 9600));
259 sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */);
260 sio_out(up, TXX9_SIDICR, 0);
261}
262
263static inline void
264receive_chars(struct uart_txx9_port *up, unsigned int *status)
265{
266 unsigned char ch;
267 unsigned int disr = *status;
268 int max_count = 256;
269 char flag;
270 unsigned int next_ignore_status_mask;
271
272 do {
273 ch = sio_in(up, TXX9_SIRFIFO);
274 flag = TTY_NORMAL;
275 up->port.icount.rx++;
276
277 /* mask out RFDN_MASK bit added by previous overrun */
278 next_ignore_status_mask =
279 up->port.ignore_status_mask & ~TXX9_SIDISR_RFDN_MASK;
280 if (unlikely(disr & (TXX9_SIDISR_UBRK | TXX9_SIDISR_UPER |
281 TXX9_SIDISR_UFER | TXX9_SIDISR_UOER))) {
282 /*
283 * For statistics only
284 */
285 if (disr & TXX9_SIDISR_UBRK) {
286 disr &= ~(TXX9_SIDISR_UFER | TXX9_SIDISR_UPER);
287 up->port.icount.brk++;
288 /*
289 * We do the SysRQ and SAK checking
290 * here because otherwise the break
291 * may get masked by ignore_status_mask
292 * or read_status_mask.
293 */
294 if (uart_handle_break(&up->port))
295 goto ignore_char;
296 } else if (disr & TXX9_SIDISR_UPER)
297 up->port.icount.parity++;
298 else if (disr & TXX9_SIDISR_UFER)
299 up->port.icount.frame++;
300 if (disr & TXX9_SIDISR_UOER) {
301 up->port.icount.overrun++;
302 /*
303 * The receiver read buffer still hold
304 * a char which caused overrun.
305 * Ignore next char by adding RFDN_MASK
306 * to ignore_status_mask temporarily.
307 */
308 next_ignore_status_mask |=
309 TXX9_SIDISR_RFDN_MASK;
310 }
311
312 /*
313 * Mask off conditions which should be ingored.
314 */
315 disr &= up->port.read_status_mask;
316
317 if (disr & TXX9_SIDISR_UBRK) {
318 flag = TTY_BREAK;
319 } else if (disr & TXX9_SIDISR_UPER)
320 flag = TTY_PARITY;
321 else if (disr & TXX9_SIDISR_UFER)
322 flag = TTY_FRAME;
323 }
324 if (uart_handle_sysrq_char(&up->port, ch))
325 goto ignore_char;
326
327 uart_insert_char(&up->port, disr, TXX9_SIDISR_UOER, ch, flag);
328
329 ignore_char:
330 up->port.ignore_status_mask = next_ignore_status_mask;
331 disr = sio_in(up, TXX9_SIDISR);
332 } while (!(disr & TXX9_SIDISR_UVALID) && (max_count-- > 0));
333 spin_unlock(&up->port.lock);
334 tty_flip_buffer_push(&up->port.state->port);
335 spin_lock(&up->port.lock);
336 *status = disr;
337}
338
339static inline void transmit_chars(struct uart_txx9_port *up)
340{
341 struct circ_buf *xmit = &up->port.state->xmit;
342 int count;
343
344 if (up->port.x_char) {
345 sio_out(up, TXX9_SITFIFO, up->port.x_char);
346 up->port.icount.tx++;
347 up->port.x_char = 0;
348 return;
349 }
350 if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
351 serial_txx9_stop_tx(&up->port);
352 return;
353 }
354
355 count = TXX9_SIO_TX_FIFO;
356 do {
357 sio_out(up, TXX9_SITFIFO, xmit->buf[xmit->tail]);
358 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
359 up->port.icount.tx++;
360 if (uart_circ_empty(xmit))
361 break;
362 } while (--count > 0);
363
364 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
365 uart_write_wakeup(&up->port);
366
367 if (uart_circ_empty(xmit))
368 serial_txx9_stop_tx(&up->port);
369}
370
371static irqreturn_t serial_txx9_interrupt(int irq, void *dev_id)
372{
373 int pass_counter = 0;
374 struct uart_txx9_port *up = dev_id;
375 unsigned int status;
376
377 while (1) {
378 spin_lock(&up->port.lock);
379 status = sio_in(up, TXX9_SIDISR);
380 if (!(sio_in(up, TXX9_SIDICR) & TXX9_SIDICR_TIE))
381 status &= ~TXX9_SIDISR_TDIS;
382 if (!(status & (TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
383 TXX9_SIDISR_TOUT))) {
384 spin_unlock(&up->port.lock);
385 break;
386 }
387
388 if (status & TXX9_SIDISR_RDIS)
389 receive_chars(up, &status);
390 if (status & TXX9_SIDISR_TDIS)
391 transmit_chars(up);
392 /* Clear TX/RX Int. Status */
393 sio_mask(up, TXX9_SIDISR,
394 TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
395 TXX9_SIDISR_TOUT);
396 spin_unlock(&up->port.lock);
397
398 if (pass_counter++ > PASS_LIMIT)
399 break;
400 }
401
402 return pass_counter ? IRQ_HANDLED : IRQ_NONE;
403}
404
405static unsigned int serial_txx9_tx_empty(struct uart_port *port)
406{
407 struct uart_txx9_port *up = to_uart_txx9_port(port);
408 unsigned long flags;
409 unsigned int ret;
410
411 spin_lock_irqsave(&up->port.lock, flags);
412 ret = (sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS) ? TIOCSER_TEMT : 0;
413 spin_unlock_irqrestore(&up->port.lock, flags);
414
415 return ret;
416}
417
418static unsigned int serial_txx9_get_mctrl(struct uart_port *port)
419{
420 struct uart_txx9_port *up = to_uart_txx9_port(port);
421 unsigned int ret;
422
423 /* no modem control lines */
424 ret = TIOCM_CAR | TIOCM_DSR;
425 ret |= (sio_in(up, TXX9_SIFLCR) & TXX9_SIFLCR_RTSSC) ? 0 : TIOCM_RTS;
426 ret |= (sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS) ? 0 : TIOCM_CTS;
427
428 return ret;
429}
430
431static void serial_txx9_set_mctrl(struct uart_port *port, unsigned int mctrl)
432{
433 struct uart_txx9_port *up = to_uart_txx9_port(port);
434
435 if (mctrl & TIOCM_RTS)
436 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
437 else
438 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
439}
440
441static void serial_txx9_break_ctl(struct uart_port *port, int break_state)
442{
443 struct uart_txx9_port *up = to_uart_txx9_port(port);
444 unsigned long flags;
445
446 spin_lock_irqsave(&up->port.lock, flags);
447 if (break_state == -1)
448 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
449 else
450 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
451 spin_unlock_irqrestore(&up->port.lock, flags);
452}
453
454#if defined(CONFIG_SERIAL_TXX9_CONSOLE) || defined(CONFIG_CONSOLE_POLL)
455/*
456 * Wait for transmitter & holding register to empty
457 */
458static void wait_for_xmitr(struct uart_txx9_port *up)
459{
460 unsigned int tmout = 10000;
461
462 /* Wait up to 10ms for the character(s) to be sent. */
463 while (--tmout &&
464 !(sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS))
465 udelay(1);
466
467 /* Wait up to 1s for flow control if necessary */
468 if (up->port.flags & UPF_CONS_FLOW) {
469 tmout = 1000000;
470 while (--tmout &&
471 (sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS))
472 udelay(1);
473 }
474}
475#endif
476
477#ifdef CONFIG_CONSOLE_POLL
478/*
479 * Console polling routines for writing and reading from the uart while
480 * in an interrupt or debug context.
481 */
482
483static int serial_txx9_get_poll_char(struct uart_port *port)
484{
485 unsigned int ier;
486 unsigned char c;
487 struct uart_txx9_port *up = to_uart_txx9_port(port);
488
489 /*
490 * First save the IER then disable the interrupts
491 */
492 ier = sio_in(up, TXX9_SIDICR);
493 sio_out(up, TXX9_SIDICR, 0);
494
495 while (sio_in(up, TXX9_SIDISR) & TXX9_SIDISR_UVALID)
496 ;
497
498 c = sio_in(up, TXX9_SIRFIFO);
499
500 /*
501 * Finally, clear RX interrupt status
502 * and restore the IER
503 */
504 sio_mask(up, TXX9_SIDISR, TXX9_SIDISR_RDIS);
505 sio_out(up, TXX9_SIDICR, ier);
506 return c;
507}
508
509
510static void serial_txx9_put_poll_char(struct uart_port *port, unsigned char c)
511{
512 unsigned int ier;
513 struct uart_txx9_port *up = to_uart_txx9_port(port);
514
515 /*
516 * First save the IER then disable the interrupts
517 */
518 ier = sio_in(up, TXX9_SIDICR);
519 sio_out(up, TXX9_SIDICR, 0);
520
521 wait_for_xmitr(up);
522 /*
523 * Send the character out.
524 */
525 sio_out(up, TXX9_SITFIFO, c);
526
527 /*
528 * Finally, wait for transmitter to become empty
529 * and restore the IER
530 */
531 wait_for_xmitr(up);
532 sio_out(up, TXX9_SIDICR, ier);
533}
534
535#endif /* CONFIG_CONSOLE_POLL */
536
537static int serial_txx9_startup(struct uart_port *port)
538{
539 struct uart_txx9_port *up = to_uart_txx9_port(port);
540 unsigned long flags;
541 int retval;
542
543 /*
544 * Clear the FIFO buffers and disable them.
545 * (they will be reenabled in set_termios())
546 */
547 sio_set(up, TXX9_SIFCR,
548 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
549 /* clear reset */
550 sio_mask(up, TXX9_SIFCR,
551 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
552 sio_out(up, TXX9_SIDICR, 0);
553
554 /*
555 * Clear the interrupt registers.
556 */
557 sio_out(up, TXX9_SIDISR, 0);
558
559 retval = request_irq(up->port.irq, serial_txx9_interrupt,
560 IRQF_SHARED, "serial_txx9", up);
561 if (retval)
562 return retval;
563
564 /*
565 * Now, initialize the UART
566 */
567 spin_lock_irqsave(&up->port.lock, flags);
568 serial_txx9_set_mctrl(&up->port, up->port.mctrl);
569 spin_unlock_irqrestore(&up->port.lock, flags);
570
571 /* Enable RX/TX */
572 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
573
574 /*
575 * Finally, enable interrupts.
576 */
577 sio_set(up, TXX9_SIDICR, TXX9_SIDICR_RIE);
578
579 return 0;
580}
581
582static void serial_txx9_shutdown(struct uart_port *port)
583{
584 struct uart_txx9_port *up = to_uart_txx9_port(port);
585 unsigned long flags;
586
587 /*
588 * Disable interrupts from this port
589 */
590 sio_out(up, TXX9_SIDICR, 0); /* disable all intrs */
591
592 spin_lock_irqsave(&up->port.lock, flags);
593 serial_txx9_set_mctrl(&up->port, up->port.mctrl);
594 spin_unlock_irqrestore(&up->port.lock, flags);
595
596 /*
597 * Disable break condition
598 */
599 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
600
601#ifdef CONFIG_SERIAL_TXX9_CONSOLE
602 if (up->port.cons && up->port.line == up->port.cons->index) {
603 free_irq(up->port.irq, up);
604 return;
605 }
606#endif
607 /* reset FIFOs */
608 sio_set(up, TXX9_SIFCR,
609 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
610 /* clear reset */
611 sio_mask(up, TXX9_SIFCR,
612 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
613
614 /* Disable RX/TX */
615 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
616
617 free_irq(up->port.irq, up);
618}
619
620static void
621serial_txx9_set_termios(struct uart_port *port, struct ktermios *termios,
622 struct ktermios *old)
623{
624 struct uart_txx9_port *up = to_uart_txx9_port(port);
625 unsigned int cval, fcr = 0;
626 unsigned long flags;
627 unsigned int baud, quot;
628
629 /*
630 * We don't support modem control lines.
631 */
632 termios->c_cflag &= ~(HUPCL | CMSPAR);
633 termios->c_cflag |= CLOCAL;
634
635 cval = sio_in(up, TXX9_SILCR);
636 /* byte size and parity */
637 cval &= ~TXX9_SILCR_UMODE_MASK;
638 switch (termios->c_cflag & CSIZE) {
639 case CS7:
640 cval |= TXX9_SILCR_UMODE_7BIT;
641 break;
642 default:
643 case CS5: /* not supported */
644 case CS6: /* not supported */
645 case CS8:
646 cval |= TXX9_SILCR_UMODE_8BIT;
647 break;
648 }
649
650 cval &= ~TXX9_SILCR_USBL_MASK;
651 if (termios->c_cflag & CSTOPB)
652 cval |= TXX9_SILCR_USBL_2BIT;
653 else
654 cval |= TXX9_SILCR_USBL_1BIT;
655 cval &= ~(TXX9_SILCR_UPEN | TXX9_SILCR_UEPS);
656 if (termios->c_cflag & PARENB)
657 cval |= TXX9_SILCR_UPEN;
658 if (!(termios->c_cflag & PARODD))
659 cval |= TXX9_SILCR_UEPS;
660
661 /*
662 * Ask the core to calculate the divisor for us.
663 */
664 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16/2);
665 quot = uart_get_divisor(port, baud);
666
667 /* Set up FIFOs */
668 /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
669 fcr = TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1;
670
671 /*
672 * Ok, we're now changing the port state. Do it with
673 * interrupts disabled.
674 */
675 spin_lock_irqsave(&up->port.lock, flags);
676
677 /*
678 * Update the per-port timeout.
679 */
680 uart_update_timeout(port, termios->c_cflag, baud);
681
682 up->port.read_status_mask = TXX9_SIDISR_UOER |
683 TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS;
684 if (termios->c_iflag & INPCK)
685 up->port.read_status_mask |= TXX9_SIDISR_UFER | TXX9_SIDISR_UPER;
686 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
687 up->port.read_status_mask |= TXX9_SIDISR_UBRK;
688
689 /*
690 * Characteres to ignore
691 */
692 up->port.ignore_status_mask = 0;
693 if (termios->c_iflag & IGNPAR)
694 up->port.ignore_status_mask |= TXX9_SIDISR_UPER | TXX9_SIDISR_UFER;
695 if (termios->c_iflag & IGNBRK) {
696 up->port.ignore_status_mask |= TXX9_SIDISR_UBRK;
697 /*
698 * If we're ignoring parity and break indicators,
699 * ignore overruns too (for real raw support).
700 */
701 if (termios->c_iflag & IGNPAR)
702 up->port.ignore_status_mask |= TXX9_SIDISR_UOER;
703 }
704
705 /*
706 * ignore all characters if CREAD is not set
707 */
708 if ((termios->c_cflag & CREAD) == 0)
709 up->port.ignore_status_mask |= TXX9_SIDISR_RDIS;
710
711 /* CTS flow control flag */
712 if ((termios->c_cflag & CRTSCTS) &&
713 (up->port.flags & UPF_TXX9_HAVE_CTS_LINE)) {
714 sio_set(up, TXX9_SIFLCR,
715 TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
716 } else {
717 sio_mask(up, TXX9_SIFLCR,
718 TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
719 }
720
721 sio_out(up, TXX9_SILCR, cval);
722 sio_quot_set(up, quot);
723 sio_out(up, TXX9_SIFCR, fcr);
724
725 serial_txx9_set_mctrl(&up->port, up->port.mctrl);
726 spin_unlock_irqrestore(&up->port.lock, flags);
727}
728
729static void
730serial_txx9_pm(struct uart_port *port, unsigned int state,
731 unsigned int oldstate)
732{
733 /*
734 * If oldstate was -1 this is called from
735 * uart_configure_port(). In this case do not initialize the
736 * port now, because the port was already initialized (for
737 * non-console port) or should not be initialized here (for
738 * console port). If we initialized the port here we lose
739 * serial console settings.
740 */
741 if (state == 0 && oldstate != -1)
742 serial_txx9_initialize(port);
743}
744
745static int serial_txx9_request_resource(struct uart_txx9_port *up)
746{
747 unsigned int size = TXX9_REGION_SIZE;
748 int ret = 0;
749
750 switch (up->port.iotype) {
751 default:
752 if (!up->port.mapbase)
753 break;
754
755 if (!request_mem_region(up->port.mapbase, size, "serial_txx9")) {
756 ret = -EBUSY;
757 break;
758 }
759
760 if (up->port.flags & UPF_IOREMAP) {
761 up->port.membase = ioremap(up->port.mapbase, size);
762 if (!up->port.membase) {
763 release_mem_region(up->port.mapbase, size);
764 ret = -ENOMEM;
765 }
766 }
767 break;
768
769 case UPIO_PORT:
770 if (!request_region(up->port.iobase, size, "serial_txx9"))
771 ret = -EBUSY;
772 break;
773 }
774 return ret;
775}
776
777static void serial_txx9_release_resource(struct uart_txx9_port *up)
778{
779 unsigned int size = TXX9_REGION_SIZE;
780
781 switch (up->port.iotype) {
782 default:
783 if (!up->port.mapbase)
784 break;
785
786 if (up->port.flags & UPF_IOREMAP) {
787 iounmap(up->port.membase);
788 up->port.membase = NULL;
789 }
790
791 release_mem_region(up->port.mapbase, size);
792 break;
793
794 case UPIO_PORT:
795 release_region(up->port.iobase, size);
796 break;
797 }
798}
799
800static void serial_txx9_release_port(struct uart_port *port)
801{
802 struct uart_txx9_port *up = to_uart_txx9_port(port);
803 serial_txx9_release_resource(up);
804}
805
806static int serial_txx9_request_port(struct uart_port *port)
807{
808 struct uart_txx9_port *up = to_uart_txx9_port(port);
809 return serial_txx9_request_resource(up);
810}
811
812static void serial_txx9_config_port(struct uart_port *port, int uflags)
813{
814 struct uart_txx9_port *up = to_uart_txx9_port(port);
815 int ret;
816
817 /*
818 * Find the region that we can probe for. This in turn
819 * tells us whether we can probe for the type of port.
820 */
821 ret = serial_txx9_request_resource(up);
822 if (ret < 0)
823 return;
824 port->type = PORT_TXX9;
825 up->port.fifosize = TXX9_SIO_TX_FIFO;
826
827#ifdef CONFIG_SERIAL_TXX9_CONSOLE
828 if (up->port.line == up->port.cons->index)
829 return;
830#endif
831 serial_txx9_initialize(port);
832}
833
834static const char *
835serial_txx9_type(struct uart_port *port)
836{
837 return "txx9";
838}
839
840static const struct uart_ops serial_txx9_pops = {
841 .tx_empty = serial_txx9_tx_empty,
842 .set_mctrl = serial_txx9_set_mctrl,
843 .get_mctrl = serial_txx9_get_mctrl,
844 .stop_tx = serial_txx9_stop_tx,
845 .start_tx = serial_txx9_start_tx,
846 .stop_rx = serial_txx9_stop_rx,
847 .break_ctl = serial_txx9_break_ctl,
848 .startup = serial_txx9_startup,
849 .shutdown = serial_txx9_shutdown,
850 .set_termios = serial_txx9_set_termios,
851 .pm = serial_txx9_pm,
852 .type = serial_txx9_type,
853 .release_port = serial_txx9_release_port,
854 .request_port = serial_txx9_request_port,
855 .config_port = serial_txx9_config_port,
856#ifdef CONFIG_CONSOLE_POLL
857 .poll_get_char = serial_txx9_get_poll_char,
858 .poll_put_char = serial_txx9_put_poll_char,
859#endif
860};
861
862static struct uart_txx9_port serial_txx9_ports[UART_NR];
863
864static void __init serial_txx9_register_ports(struct uart_driver *drv,
865 struct device *dev)
866{
867 int i;
868
869 for (i = 0; i < UART_NR; i++) {
870 struct uart_txx9_port *up = &serial_txx9_ports[i];
871
872 up->port.line = i;
873 up->port.ops = &serial_txx9_pops;
874 up->port.dev = dev;
875 if (up->port.iobase || up->port.mapbase)
876 uart_add_one_port(drv, &up->port);
877 }
878}
879
880#ifdef CONFIG_SERIAL_TXX9_CONSOLE
881
882static void serial_txx9_console_putchar(struct uart_port *port, int ch)
883{
884 struct uart_txx9_port *up = to_uart_txx9_port(port);
885
886 wait_for_xmitr(up);
887 sio_out(up, TXX9_SITFIFO, ch);
888}
889
890/*
891 * Print a string to the serial port trying not to disturb
892 * any possible real use of the port...
893 *
894 * The console_lock must be held when we get here.
895 */
896static void
897serial_txx9_console_write(struct console *co, const char *s, unsigned int count)
898{
899 struct uart_txx9_port *up = &serial_txx9_ports[co->index];
900 unsigned int ier, flcr;
901
902 /*
903 * First save the UER then disable the interrupts
904 */
905 ier = sio_in(up, TXX9_SIDICR);
906 sio_out(up, TXX9_SIDICR, 0);
907 /*
908 * Disable flow-control if enabled (and unnecessary)
909 */
910 flcr = sio_in(up, TXX9_SIFLCR);
911 if (!(up->port.flags & UPF_CONS_FLOW) && (flcr & TXX9_SIFLCR_TES))
912 sio_out(up, TXX9_SIFLCR, flcr & ~TXX9_SIFLCR_TES);
913
914 uart_console_write(&up->port, s, count, serial_txx9_console_putchar);
915
916 /*
917 * Finally, wait for transmitter to become empty
918 * and restore the IER
919 */
920 wait_for_xmitr(up);
921 sio_out(up, TXX9_SIFLCR, flcr);
922 sio_out(up, TXX9_SIDICR, ier);
923}
924
925static int __init serial_txx9_console_setup(struct console *co, char *options)
926{
927 struct uart_port *port;
928 struct uart_txx9_port *up;
929 int baud = 9600;
930 int bits = 8;
931 int parity = 'n';
932 int flow = 'n';
933
934 /*
935 * Check whether an invalid uart number has been specified, and
936 * if so, search for the first available port that does have
937 * console support.
938 */
939 if (co->index >= UART_NR)
940 co->index = 0;
941 up = &serial_txx9_ports[co->index];
942 port = &up->port;
943 if (!port->ops)
944 return -ENODEV;
945
946 serial_txx9_initialize(&up->port);
947
948 if (options)
949 uart_parse_options(options, &baud, &parity, &bits, &flow);
950
951 return uart_set_options(port, co, baud, parity, bits, flow);
952}
953
954static struct uart_driver serial_txx9_reg;
955static struct console serial_txx9_console = {
956 .name = TXX9_TTY_NAME,
957 .write = serial_txx9_console_write,
958 .device = uart_console_device,
959 .setup = serial_txx9_console_setup,
960 .flags = CON_PRINTBUFFER,
961 .index = -1,
962 .data = &serial_txx9_reg,
963};
964
965static int __init serial_txx9_console_init(void)
966{
967 register_console(&serial_txx9_console);
968 return 0;
969}
970console_initcall(serial_txx9_console_init);
971
972#define SERIAL_TXX9_CONSOLE &serial_txx9_console
973#else
974#define SERIAL_TXX9_CONSOLE NULL
975#endif
976
977static struct uart_driver serial_txx9_reg = {
978 .owner = THIS_MODULE,
979 .driver_name = "serial_txx9",
980 .dev_name = TXX9_TTY_NAME,
981 .major = TXX9_TTY_MAJOR,
982 .minor = TXX9_TTY_MINOR_START,
983 .nr = UART_NR,
984 .cons = SERIAL_TXX9_CONSOLE,
985};
986
987int __init early_serial_txx9_setup(struct uart_port *port)
988{
989 if (port->line >= ARRAY_SIZE(serial_txx9_ports))
990 return -ENODEV;
991
992 serial_txx9_ports[port->line].port = *port;
993 serial_txx9_ports[port->line].port.ops = &serial_txx9_pops;
994 serial_txx9_ports[port->line].port.flags |=
995 UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
996 return 0;
997}
998
999static DEFINE_MUTEX(serial_txx9_mutex);
1000
1001/**
1002 * serial_txx9_register_port - register a serial port
1003 * @port: serial port template
1004 *
1005 * Configure the serial port specified by the request.
1006 *
1007 * The port is then probed and if necessary the IRQ is autodetected
1008 * If this fails an error is returned.
1009 *
1010 * On success the port is ready to use and the line number is returned.
1011 */
1012static int serial_txx9_register_port(struct uart_port *port)
1013{
1014 int i;
1015 struct uart_txx9_port *uart;
1016 int ret = -ENOSPC;
1017
1018 mutex_lock(&serial_txx9_mutex);
1019 for (i = 0; i < UART_NR; i++) {
1020 uart = &serial_txx9_ports[i];
1021 if (uart_match_port(&uart->port, port)) {
1022 uart_remove_one_port(&serial_txx9_reg, &uart->port);
1023 break;
1024 }
1025 }
1026 if (i == UART_NR) {
1027 /* Find unused port */
1028 for (i = 0; i < UART_NR; i++) {
1029 uart = &serial_txx9_ports[i];
1030 if (!(uart->port.iobase || uart->port.mapbase))
1031 break;
1032 }
1033 }
1034 if (i < UART_NR) {
1035 uart->port.iobase = port->iobase;
1036 uart->port.membase = port->membase;
1037 uart->port.irq = port->irq;
1038 uart->port.uartclk = port->uartclk;
1039 uart->port.iotype = port->iotype;
1040 uart->port.flags = port->flags
1041 | UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
1042 uart->port.mapbase = port->mapbase;
1043 if (port->dev)
1044 uart->port.dev = port->dev;
1045 ret = uart_add_one_port(&serial_txx9_reg, &uart->port);
1046 if (ret == 0)
1047 ret = uart->port.line;
1048 }
1049 mutex_unlock(&serial_txx9_mutex);
1050 return ret;
1051}
1052
1053/**
1054 * serial_txx9_unregister_port - remove a txx9 serial port at runtime
1055 * @line: serial line number
1056 *
1057 * Remove one serial port. This may not be called from interrupt
1058 * context. We hand the port back to the our control.
1059 */
1060static void serial_txx9_unregister_port(int line)
1061{
1062 struct uart_txx9_port *uart = &serial_txx9_ports[line];
1063
1064 mutex_lock(&serial_txx9_mutex);
1065 uart_remove_one_port(&serial_txx9_reg, &uart->port);
1066 uart->port.flags = 0;
1067 uart->port.type = PORT_UNKNOWN;
1068 uart->port.iobase = 0;
1069 uart->port.mapbase = 0;
1070 uart->port.membase = NULL;
1071 uart->port.dev = NULL;
1072 mutex_unlock(&serial_txx9_mutex);
1073}
1074
1075/*
1076 * Register a set of serial devices attached to a platform device.
1077 */
1078static int serial_txx9_probe(struct platform_device *dev)
1079{
1080 struct uart_port *p = dev_get_platdata(&dev->dev);
1081 struct uart_port port;
1082 int ret, i;
1083
1084 memset(&port, 0, sizeof(struct uart_port));
1085 for (i = 0; p && p->uartclk != 0; p++, i++) {
1086 port.iobase = p->iobase;
1087 port.membase = p->membase;
1088 port.irq = p->irq;
1089 port.uartclk = p->uartclk;
1090 port.iotype = p->iotype;
1091 port.flags = p->flags;
1092 port.mapbase = p->mapbase;
1093 port.dev = &dev->dev;
1094 port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_TXX9_CONSOLE);
1095 ret = serial_txx9_register_port(&port);
1096 if (ret < 0) {
1097 dev_err(&dev->dev, "unable to register port at index %d "
1098 "(IO%lx MEM%llx IRQ%d): %d\n", i,
1099 p->iobase, (unsigned long long)p->mapbase,
1100 p->irq, ret);
1101 }
1102 }
1103 return 0;
1104}
1105
1106/*
1107 * Remove serial ports registered against a platform device.
1108 */
1109static int serial_txx9_remove(struct platform_device *dev)
1110{
1111 int i;
1112
1113 for (i = 0; i < UART_NR; i++) {
1114 struct uart_txx9_port *up = &serial_txx9_ports[i];
1115
1116 if (up->port.dev == &dev->dev)
1117 serial_txx9_unregister_port(i);
1118 }
1119 return 0;
1120}
1121
1122#ifdef CONFIG_PM
1123static int serial_txx9_suspend(struct platform_device *dev, pm_message_t state)
1124{
1125 int i;
1126
1127 for (i = 0; i < UART_NR; i++) {
1128 struct uart_txx9_port *up = &serial_txx9_ports[i];
1129
1130 if (up->port.type != PORT_UNKNOWN && up->port.dev == &dev->dev)
1131 uart_suspend_port(&serial_txx9_reg, &up->port);
1132 }
1133
1134 return 0;
1135}
1136
1137static int serial_txx9_resume(struct platform_device *dev)
1138{
1139 int i;
1140
1141 for (i = 0; i < UART_NR; i++) {
1142 struct uart_txx9_port *up = &serial_txx9_ports[i];
1143
1144 if (up->port.type != PORT_UNKNOWN && up->port.dev == &dev->dev)
1145 uart_resume_port(&serial_txx9_reg, &up->port);
1146 }
1147
1148 return 0;
1149}
1150#endif
1151
1152static struct platform_driver serial_txx9_plat_driver = {
1153 .probe = serial_txx9_probe,
1154 .remove = serial_txx9_remove,
1155#ifdef CONFIG_PM
1156 .suspend = serial_txx9_suspend,
1157 .resume = serial_txx9_resume,
1158#endif
1159 .driver = {
1160 .name = "serial_txx9",
1161 },
1162};
1163
1164#ifdef ENABLE_SERIAL_TXX9_PCI
1165/*
1166 * Probe one serial board. Unfortunately, there is no rhyme nor reason
1167 * to the arrangement of serial ports on a PCI card.
1168 */
1169static int
1170pciserial_txx9_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
1171{
1172 struct uart_port port;
1173 int line;
1174 int rc;
1175
1176 rc = pci_enable_device(dev);
1177 if (rc)
1178 return rc;
1179
1180 memset(&port, 0, sizeof(port));
1181 port.ops = &serial_txx9_pops;
1182 port.flags |= UPF_TXX9_HAVE_CTS_LINE;
1183 port.uartclk = 66670000;
1184 port.irq = dev->irq;
1185 port.iotype = UPIO_PORT;
1186 port.iobase = pci_resource_start(dev, 1);
1187 port.dev = &dev->dev;
1188 line = serial_txx9_register_port(&port);
1189 if (line < 0) {
1190 printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), line);
1191 pci_disable_device(dev);
1192 return line;
1193 }
1194 pci_set_drvdata(dev, &serial_txx9_ports[line]);
1195
1196 return 0;
1197}
1198
1199static void pciserial_txx9_remove_one(struct pci_dev *dev)
1200{
1201 struct uart_txx9_port *up = pci_get_drvdata(dev);
1202
1203 if (up) {
1204 serial_txx9_unregister_port(up->port.line);
1205 pci_disable_device(dev);
1206 }
1207}
1208
1209#ifdef CONFIG_PM
1210static int pciserial_txx9_suspend_one(struct pci_dev *dev, pm_message_t state)
1211{
1212 struct uart_txx9_port *up = pci_get_drvdata(dev);
1213
1214 if (up)
1215 uart_suspend_port(&serial_txx9_reg, &up->port);
1216 pci_save_state(dev);
1217 pci_set_power_state(dev, pci_choose_state(dev, state));
1218 return 0;
1219}
1220
1221static int pciserial_txx9_resume_one(struct pci_dev *dev)
1222{
1223 struct uart_txx9_port *up = pci_get_drvdata(dev);
1224
1225 pci_set_power_state(dev, PCI_D0);
1226 pci_restore_state(dev);
1227 if (up)
1228 uart_resume_port(&serial_txx9_reg, &up->port);
1229 return 0;
1230}
1231#endif
1232
1233static const struct pci_device_id serial_txx9_pci_tbl[] = {
1234 { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_TC86C001_MISC) },
1235 { 0, }
1236};
1237
1238static struct pci_driver serial_txx9_pci_driver = {
1239 .name = "serial_txx9",
1240 .probe = pciserial_txx9_init_one,
1241 .remove = pciserial_txx9_remove_one,
1242#ifdef CONFIG_PM
1243 .suspend = pciserial_txx9_suspend_one,
1244 .resume = pciserial_txx9_resume_one,
1245#endif
1246 .id_table = serial_txx9_pci_tbl,
1247};
1248
1249MODULE_DEVICE_TABLE(pci, serial_txx9_pci_tbl);
1250#endif /* ENABLE_SERIAL_TXX9_PCI */
1251
1252static struct platform_device *serial_txx9_plat_devs;
1253
1254static int __init serial_txx9_init(void)
1255{
1256 int ret;
1257
1258 printk(KERN_INFO "%s version %s\n", serial_name, serial_version);
1259
1260 ret = uart_register_driver(&serial_txx9_reg);
1261 if (ret)
1262 goto out;
1263
1264 serial_txx9_plat_devs = platform_device_alloc("serial_txx9", -1);
1265 if (!serial_txx9_plat_devs) {
1266 ret = -ENOMEM;
1267 goto unreg_uart_drv;
1268 }
1269
1270 ret = platform_device_add(serial_txx9_plat_devs);
1271 if (ret)
1272 goto put_dev;
1273
1274 serial_txx9_register_ports(&serial_txx9_reg,
1275 &serial_txx9_plat_devs->dev);
1276
1277 ret = platform_driver_register(&serial_txx9_plat_driver);
1278 if (ret)
1279 goto del_dev;
1280
1281#ifdef ENABLE_SERIAL_TXX9_PCI
1282 ret = pci_register_driver(&serial_txx9_pci_driver);
1283#endif
1284 if (ret == 0)
1285 goto out;
1286
1287 del_dev:
1288 platform_device_del(serial_txx9_plat_devs);
1289 put_dev:
1290 platform_device_put(serial_txx9_plat_devs);
1291 unreg_uart_drv:
1292 uart_unregister_driver(&serial_txx9_reg);
1293 out:
1294 return ret;
1295}
1296
1297static void __exit serial_txx9_exit(void)
1298{
1299 int i;
1300
1301#ifdef ENABLE_SERIAL_TXX9_PCI
1302 pci_unregister_driver(&serial_txx9_pci_driver);
1303#endif
1304 platform_driver_unregister(&serial_txx9_plat_driver);
1305 platform_device_unregister(serial_txx9_plat_devs);
1306 for (i = 0; i < UART_NR; i++) {
1307 struct uart_txx9_port *up = &serial_txx9_ports[i];
1308 if (up->port.iobase || up->port.mapbase)
1309 uart_remove_one_port(&serial_txx9_reg, &up->port);
1310 }
1311
1312 uart_unregister_driver(&serial_txx9_reg);
1313}
1314
1315module_init(serial_txx9_init);
1316module_exit(serial_txx9_exit);
1317
1318MODULE_LICENSE("GPL");
1319MODULE_DESCRIPTION("TX39/49 serial driver");
1320
1321MODULE_ALIAS_CHARDEV_MAJOR(TXX9_TTY_MAJOR);