Loading...
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# SPI driver configuration
4#
5menuconfig SPI
6 bool "SPI support"
7 depends on HAS_IOMEM
8 help
9 The "Serial Peripheral Interface" is a low level synchronous
10 protocol. Chips that support SPI can have data transfer rates
11 up to several tens of Mbit/sec. Chips are addressed with a
12 controller and a chipselect. Most SPI slaves don't support
13 dynamic device discovery; some are even write-only or read-only.
14
15 SPI is widely used by microcontrollers to talk with sensors,
16 eeprom and flash memory, codecs and various other controller
17 chips, analog to digital (and d-to-a) converters, and more.
18 MMC and SD cards can be accessed using SPI protocol; and for
19 DataFlash cards used in MMC sockets, SPI must always be used.
20
21 SPI is one of a family of similar protocols using a four wire
22 interface (select, clock, data in, data out) including Microwire
23 (half duplex), SSP, SSI, and PSP. This driver framework should
24 work with most such devices and controllers.
25
26if SPI
27
28config SPI_DEBUG
29 bool "Debug support for SPI drivers"
30 depends on DEBUG_KERNEL
31 help
32 Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
33 sysfs, and debugfs support in SPI controller and protocol drivers.
34
35#
36# MASTER side ... talking to discrete SPI slave chips including microcontrollers
37#
38
39config SPI_MASTER
40# bool "SPI Master Support"
41 bool
42 default SPI
43 help
44 If your system has an master-capable SPI controller (which
45 provides the clock and chipselect), you can enable that
46 controller and the protocol drivers for the SPI slave chips
47 that are connected.
48
49if SPI_MASTER
50
51config SPI_MEM
52 bool "SPI memory extension"
53 help
54 Enable this option if you want to enable the SPI memory extension.
55 This extension is meant to simplify interaction with SPI memories
56 by providing a high-level interface to send memory-like commands.
57
58comment "SPI Master Controller Drivers"
59
60config SPI_ALTERA
61 tristate "Altera SPI Controller platform driver"
62 select SPI_ALTERA_CORE
63 select REGMAP_MMIO
64 help
65 This is the driver for the Altera SPI Controller.
66
67config SPI_ALTERA_CORE
68 tristate "Altera SPI Controller core code" if COMPILE_TEST
69 select REGMAP
70 help
71 "The core code for the Altera SPI Controller"
72
73config SPI_ALTERA_DFL
74 tristate "DFL bus driver for Altera SPI Controller"
75 depends on FPGA_DFL
76 select SPI_ALTERA_CORE
77 help
78 This is a Device Feature List (DFL) bus driver for the
79 Altera SPI master controller. The SPI master is connected
80 to a SPI slave to Avalon bridge in a Intel MAX BMC.
81
82config SPI_AR934X
83 tristate "Qualcomm Atheros AR934X/QCA95XX SPI controller driver"
84 depends on ATH79 || COMPILE_TEST
85 help
86 This enables support for the SPI controller present on the
87 Qualcomm Atheros AR934X/QCA95XX SoCs.
88
89config SPI_ATH79
90 tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
91 depends on ATH79 || COMPILE_TEST
92 select SPI_BITBANG
93 help
94 This enables support for the SPI controller present on the
95 Atheros AR71XX/AR724X/AR913X SoCs.
96
97config SPI_ARMADA_3700
98 tristate "Marvell Armada 3700 SPI Controller"
99 depends on (ARCH_MVEBU && OF) || COMPILE_TEST
100 help
101 This enables support for the SPI controller present on the
102 Marvell Armada 3700 SoCs.
103
104config SPI_ASPEED_SMC
105 tristate "Aspeed flash controllers in SPI mode"
106 depends on ARCH_ASPEED || COMPILE_TEST
107 depends on OF
108 help
109 This enables support for the Firmware Memory controller (FMC)
110 in the Aspeed AST2600, AST2500 and AST2400 SoCs when attached
111 to SPI NOR chips, and support for the SPI flash memory
112 controller (SPI) for the host firmware. The implementation
113 only supports SPI NOR.
114
115config SPI_ATMEL
116 tristate "Atmel SPI Controller"
117 depends on ARCH_AT91 || COMPILE_TEST
118 depends on OF
119 help
120 This selects a driver for the Atmel SPI Controller, present on
121 many AT91 ARM chips.
122
123config SPI_AT91_USART
124 tristate "Atmel USART Controller SPI driver"
125 depends on (ARCH_AT91 || COMPILE_TEST)
126 depends on MFD_AT91_USART
127 help
128 This selects a driver for the AT91 USART Controller as SPI Master,
129 present on AT91 and SAMA5 SoC series.
130
131config SPI_ATMEL_QUADSPI
132 tristate "Atmel Quad SPI Controller"
133 depends on ARCH_AT91 || COMPILE_TEST
134 depends on OF && HAS_IOMEM
135 help
136 This enables support for the Quad SPI controller in master mode.
137 This driver does not support generic SPI. The implementation only
138 supports spi-mem interface.
139
140config SPI_AU1550
141 tristate "Au1550/Au1200/Au1300 SPI Controller"
142 depends on MIPS_ALCHEMY
143 select SPI_BITBANG
144 help
145 If you say yes to this option, support will be included for the
146 PSC SPI controller found on Au1550, Au1200 and Au1300 series.
147
148config SPI_AXI_SPI_ENGINE
149 tristate "Analog Devices AXI SPI Engine controller"
150 depends on HAS_IOMEM
151 help
152 This enables support for the Analog Devices AXI SPI Engine SPI controller.
153 It is part of the SPI Engine framework that is used in some Analog Devices
154 reference designs for FPGAs.
155
156config SPI_BCM2835
157 tristate "BCM2835 SPI controller"
158 depends on GPIOLIB
159 depends on ARCH_BCM2835 || ARCH_BRCMSTB || COMPILE_TEST
160 help
161 This selects a driver for the Broadcom BCM2835 SPI master.
162
163 The BCM2835 contains two types of SPI master controller; the
164 "universal SPI master", and the regular SPI controller. This driver
165 is for the regular SPI controller. Slave mode operation is not also
166 not supported.
167
168config SPI_BCM2835AUX
169 tristate "BCM2835 SPI auxiliary controller"
170 depends on ((ARCH_BCM2835 || ARCH_BRCMSTB) && GPIOLIB) || COMPILE_TEST
171 help
172 This selects a driver for the Broadcom BCM2835 SPI aux master.
173
174 The BCM2835 contains two types of SPI master controller; the
175 "universal SPI master", and the regular SPI controller.
176 This driver is for the universal/auxiliary SPI controller.
177
178config SPI_BCM63XX
179 tristate "Broadcom BCM63xx SPI controller"
180 depends on BCM63XX || BMIPS_GENERIC || COMPILE_TEST
181 help
182 Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
183
184config SPI_BCM63XX_HSSPI
185 tristate "Broadcom BCM63XX HS SPI controller driver"
186 depends on BCM63XX || BMIPS_GENERIC || ARCH_BCMBCA || COMPILE_TEST
187 help
188 This enables support for the High Speed SPI controller present on
189 newer Broadcom BCM63XX SoCs.
190
191config SPI_BCM_QSPI
192 tristate "Broadcom BSPI and MSPI controller support"
193 depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || \
194 BMIPS_GENERIC || COMPILE_TEST
195 default ARCH_BCM_IPROC
196 help
197 Enables support for the Broadcom SPI flash and MSPI controller.
198 Select this option for any one of BRCMSTB, iProc NSP and NS2 SoCs
199 based platforms. This driver works for both SPI master for SPI NOR
200 flash device as well as MSPI device.
201
202config SPI_BITBANG
203 tristate "Utilities for Bitbanging SPI masters"
204 help
205 With a few GPIO pins, your system can bitbang the SPI protocol.
206 Select this to get SPI support through I/O pins (GPIO, parallel
207 port, etc). Or, some systems' SPI master controller drivers use
208 this code to manage the per-word or per-transfer accesses to the
209 hardware shift registers.
210
211 This is library code, and is automatically selected by drivers that
212 need it. You only need to select this explicitly to support driver
213 modules that aren't part of this kernel tree.
214
215config SPI_BUTTERFLY
216 tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
217 depends on PARPORT
218 select SPI_BITBANG
219 help
220 This uses a custom parallel port cable to connect to an AVR
221 Butterfly <http://www.atmel.com/products/avr/butterfly>, an
222 inexpensive battery powered microcontroller evaluation board.
223 This same cable can be used to flash new firmware.
224
225config SPI_CADENCE
226 tristate "Cadence SPI controller"
227 help
228 This selects the Cadence SPI controller master driver
229 used by Xilinx Zynq and ZynqMP.
230
231config SPI_CADENCE_QUADSPI
232 tristate "Cadence Quad SPI controller"
233 depends on OF && (ARM || ARM64 || X86 || COMPILE_TEST)
234 help
235 Enable support for the Cadence Quad SPI Flash controller.
236
237 Cadence QSPI is a specialized controller for connecting an SPI
238 Flash over 1/2/4-bit wide bus. Enable this option if you have a
239 device with a Cadence QSPI controller and want to access the
240 Flash as an MTD device.
241
242config SPI_CADENCE_XSPI
243 tristate "Cadence XSPI controller"
244 depends on OF && HAS_IOMEM
245 depends on SPI_MEM
246 help
247 Enable support for the Cadence XSPI Flash controller.
248
249 Cadence XSPI is a specialized controller for connecting an SPI
250 Flash over upto 8bit wide bus. Enable this option if you have a
251 device with a Cadence XSPI controller and want to access the
252 Flash as an MTD device.
253
254config SPI_CLPS711X
255 tristate "CLPS711X host SPI controller"
256 depends on ARCH_CLPS711X || COMPILE_TEST
257 help
258 This enables dedicated general purpose SPI/Microwire1-compatible
259 master mode interface (SSI1) for CLPS711X-based CPUs.
260
261config SPI_COLDFIRE_QSPI
262 tristate "Freescale Coldfire QSPI controller"
263 depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
264 help
265 This enables support for the Coldfire QSPI controller in master
266 mode.
267
268config SPI_DAVINCI
269 tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
270 depends on ARCH_DAVINCI || ARCH_KEYSTONE
271 select SPI_BITBANG
272 help
273 SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
274
275config SPI_DESIGNWARE
276 tristate "DesignWare SPI controller core support"
277 imply SPI_MEM
278 help
279 general driver for SPI controller core from DesignWare
280
281if SPI_DESIGNWARE
282
283config SPI_DW_DMA
284 bool "DMA support for DW SPI controller"
285
286config SPI_DW_PCI
287 tristate "PCI interface driver for DW SPI core"
288 depends on PCI
289
290config SPI_DW_MMIO
291 tristate "Memory-mapped io interface driver for DW SPI core"
292 depends on HAS_IOMEM
293
294config SPI_DW_BT1
295 tristate "Baikal-T1 SPI driver for DW SPI core"
296 depends on MIPS_BAIKAL_T1 || COMPILE_TEST
297 select MULTIPLEXER
298 select MUX_MMIO
299 help
300 Baikal-T1 SoC is equipped with three DW APB SSI-based MMIO SPI
301 controllers. Two of them are pretty much normal: with IRQ, DMA,
302 FIFOs of 64 words depth, 4x CSs, but the third one as being a
303 part of the Baikal-T1 System Boot Controller has got a very
304 limited resources: no IRQ, no DMA, only a single native
305 chip-select and Tx/Rx FIFO with just 8 words depth available.
306 The later one is normally connected to an external SPI-nor flash
307 of 128Mb (in general can be of bigger size).
308
309config SPI_DW_BT1_DIRMAP
310 bool "Directly mapped Baikal-T1 Boot SPI flash support"
311 depends on SPI_DW_BT1
312 help
313 Directly mapped SPI flash memory is an interface specific to the
314 Baikal-T1 System Boot Controller. It is a 16MB MMIO region, which
315 can be used to access a peripheral memory device just by
316 reading/writing data from/to it. Note that the system APB bus
317 will stall during each IO from/to the dirmap region until the
318 operation is finished. So try not to use it concurrently with
319 time-critical tasks (like the SPI memory operations implemented
320 in this driver).
321
322endif
323
324config SPI_DLN2
325 tristate "Diolan DLN-2 USB SPI adapter"
326 depends on MFD_DLN2
327 help
328 If you say yes to this option, support will be included for Diolan
329 DLN2, a USB to SPI interface.
330
331 This driver can also be built as a module. If so, the module
332 will be called spi-dln2.
333
334config SPI_EP93XX
335 tristate "Cirrus Logic EP93xx SPI controller"
336 depends on ARCH_EP93XX || COMPILE_TEST
337 help
338 This enables using the Cirrus EP93xx SPI controller in master
339 mode.
340
341config SPI_FALCON
342 bool "Falcon SPI controller support"
343 depends on SOC_FALCON
344 help
345 The external bus unit (EBU) found on the FALC-ON SoC has SPI
346 emulation that is designed for serial flash access. This driver
347 has only been tested with m25p80 type chips. The hardware has no
348 support for other types of SPI peripherals.
349
350config SPI_FSI
351 tristate "FSI SPI driver"
352 depends on FSI
353 help
354 This enables support for the driver for FSI bus attached SPI
355 controllers.
356
357config SPI_FSL_LPSPI
358 tristate "Freescale i.MX LPSPI controller"
359 depends on ARCH_MXC || COMPILE_TEST
360 help
361 This enables Freescale i.MX LPSPI controllers in master mode.
362
363config SPI_FSL_QUADSPI
364 tristate "Freescale QSPI controller"
365 depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
366 depends on HAS_IOMEM
367 help
368 This enables support for the Quad SPI controller in master mode.
369 Up to four flash chips can be connected on two buses with two
370 chipselects each.
371 This controller does not support generic SPI messages. It only
372 supports the high-level SPI memory interface.
373
374config SPI_GXP
375 tristate "GXP SPI driver"
376 depends on ARCH_HPE || COMPILE_TEST
377 help
378 This enables support for the driver for GXP bus attached SPI
379 controllers.
380
381config SPI_HISI_KUNPENG
382 tristate "HiSilicon SPI Controller for Kunpeng SoCs"
383 depends on (ARM64 && ACPI) || COMPILE_TEST
384 help
385 This enables support for HiSilicon SPI controller found on
386 Kunpeng SoCs.
387
388 This driver can also be built as a module. If so, the module
389 will be called hisi-kunpeng-spi.
390
391config SPI_HISI_SFC_V3XX
392 tristate "HiSilicon SPI NOR Flash Controller for Hi16XX chipsets"
393 depends on (ARM64 && ACPI) || COMPILE_TEST
394 depends on HAS_IOMEM
395 help
396 This enables support for HiSilicon v3xx SPI NOR flash controller
397 found in hi16xx chipsets.
398
399config SPI_NXP_FLEXSPI
400 tristate "NXP Flex SPI controller"
401 depends on ARCH_LAYERSCAPE || HAS_IOMEM
402 help
403 This enables support for the Flex SPI controller in master mode.
404 Up to four slave devices can be connected on two buses with two
405 chipselects each.
406 This controller does not support generic SPI messages and only
407 supports the high-level SPI memory interface.
408
409config SPI_GPIO
410 tristate "GPIO-based bitbanging SPI Master"
411 depends on GPIOLIB || COMPILE_TEST
412 select SPI_BITBANG
413 help
414 This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
415 interface to manage MOSI, MISO, SCK, and chipselect signals. SPI
416 slaves connected to a bus using this driver are configured as usual,
417 except that the spi_board_info.controller_data holds the GPIO number
418 for the chipselect used by this controller driver.
419
420 Note that this driver often won't achieve even 1 Mbit/sec speeds,
421 making it unusually slow for SPI. If your platform can inline
422 GPIO operations, you should be able to leverage that for better
423 speed with a custom version of this driver; see the source code.
424
425config SPI_IMG_SPFI
426 tristate "IMG SPFI controller"
427 depends on MIPS || COMPILE_TEST
428 help
429 This enables support for the SPFI master controller found on
430 IMG SoCs.
431
432config SPI_IMX
433 tristate "Freescale i.MX SPI controllers"
434 depends on ARCH_MXC || COMPILE_TEST
435 help
436 This enables support for the Freescale i.MX SPI controllers.
437
438config SPI_INGENIC
439 tristate "Ingenic SoCs SPI controller"
440 depends on MACH_INGENIC || COMPILE_TEST
441 help
442 This enables support for the Ingenic SoCs SPI controller.
443
444 To compile this driver as a module, choose M here: the module
445 will be called spi-ingenic.
446
447config SPI_INTEL
448 tristate
449
450config SPI_INTEL_PCI
451 tristate "Intel PCH/PCU SPI flash PCI driver (DANGEROUS)"
452 depends on PCI
453 depends on X86 || COMPILE_TEST
454 depends on SPI_MEM
455 select SPI_INTEL
456 help
457 This enables PCI support for the Intel PCH/PCU SPI controller in
458 master mode. This controller is present in modern Intel hardware
459 and is used to hold BIOS and other persistent settings. Using
460 this driver it is possible to upgrade BIOS directly from Linux.
461
462 Say N here unless you know what you are doing. Overwriting the
463 SPI flash may render the system unbootable.
464
465 To compile this driver as a module, choose M here: the module
466 will be called spi-intel-pci.
467
468config SPI_INTEL_PLATFORM
469 tristate "Intel PCH/PCU SPI flash platform driver (DANGEROUS)"
470 depends on X86 || COMPILE_TEST
471 depends on SPI_MEM
472 select SPI_INTEL
473 help
474 This enables platform support for the Intel PCH/PCU SPI
475 controller in master mode. This controller is present in modern
476 Intel hardware and is used to hold BIOS and other persistent
477 settings. Using this driver it is possible to upgrade BIOS
478 directly from Linux.
479
480 Say N here unless you know what you are doing. Overwriting the
481 SPI flash may render the system unbootable.
482
483 To compile this driver as a module, choose M here: the module
484 will be called spi-intel-platform.
485
486config SPI_JCORE
487 tristate "J-Core SPI Master"
488 depends on OF && (SUPERH || COMPILE_TEST)
489 help
490 This enables support for the SPI master controller in the J-Core
491 synthesizable, open source SoC.
492
493config SPI_LM70_LLP
494 tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
495 depends on PARPORT
496 select SPI_BITBANG
497 help
498 This driver supports the NS LM70 LLP Evaluation Board,
499 which interfaces to an LM70 temperature sensor using
500 a parallel port.
501
502config SPI_LP8841_RTC
503 tristate "ICP DAS LP-8841 SPI Controller for RTC"
504 depends on MACH_PXA27X_DT || COMPILE_TEST
505 help
506 This driver provides an SPI master device to drive Maxim
507 DS-1302 real time clock.
508
509 Say N here unless you plan to run the kernel on an ICP DAS
510 LP-8x4x industrial computer.
511
512config SPI_MPC52xx
513 tristate "Freescale MPC52xx SPI (non-PSC) controller support"
514 depends on PPC_MPC52xx
515 help
516 This drivers supports the MPC52xx SPI controller in master SPI
517 mode.
518
519config SPI_MPC52xx_PSC
520 tristate "Freescale MPC52xx PSC SPI controller"
521 depends on PPC_MPC52xx
522 help
523 This enables using the Freescale MPC52xx Programmable Serial
524 Controller in master SPI mode.
525
526config SPI_MPC512x_PSC
527 tristate "Freescale MPC512x PSC SPI controller"
528 depends on PPC_MPC512x
529 help
530 This enables using the Freescale MPC5121 Programmable Serial
531 Controller in SPI master mode.
532
533config SPI_FSL_LIB
534 tristate
535 depends on OF
536
537config SPI_FSL_CPM
538 tristate
539 depends on FSL_SOC
540
541config SPI_FSL_SPI
542 tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
543 depends on OF
544 select SPI_FSL_LIB
545 select SPI_FSL_CPM if FSL_SOC
546 help
547 This enables using the Freescale SPI controllers in master mode.
548 MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
549 MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
550 This also enables using the Aeroflex Gaisler GRLIB SPI controller in
551 master mode.
552
553config SPI_FSL_DSPI
554 tristate "Freescale DSPI controller"
555 select REGMAP_MMIO
556 depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || M5441x || COMPILE_TEST
557 help
558 This enables support for the Freescale DSPI controller in master
559 mode. VF610, LS1021A and ColdFire platforms uses the controller.
560
561config SPI_FSL_ESPI
562 tristate "Freescale eSPI controller"
563 depends on FSL_SOC
564 help
565 This enables using the Freescale eSPI controllers in master mode.
566 From MPC8536, 85xx platform uses the controller, and all P10xx,
567 P20xx, P30xx,P40xx, P50xx uses this controller.
568
569config SPI_MESON_SPICC
570 tristate "Amlogic Meson SPICC controller"
571 depends on COMMON_CLK
572 depends on ARCH_MESON || COMPILE_TEST
573 help
574 This enables master mode support for the SPICC (SPI communication
575 controller) available in Amlogic Meson SoCs.
576
577config SPI_MESON_SPIFC
578 tristate "Amlogic Meson SPIFC controller"
579 depends on ARCH_MESON || COMPILE_TEST
580 select REGMAP_MMIO
581 help
582 This enables master mode support for the SPIFC (SPI flash
583 controller) available in Amlogic Meson SoCs.
584
585config SPI_MICROCHIP_CORE
586 tristate "Microchip FPGA SPI controllers"
587 depends on SPI_MASTER
588 help
589 This enables the SPI driver for Microchip FPGA SPI controllers.
590 Say Y or M here if you want to use the "hard" controllers on
591 PolarFire SoC.
592 If built as a module, it will be called spi-microchip-core.
593
594config SPI_MICROCHIP_CORE_QSPI
595 tristate "Microchip FPGA QSPI controllers"
596 depends on SPI_MASTER
597 help
598 This enables the QSPI driver for Microchip FPGA QSPI controllers.
599 Say Y or M here if you want to use the QSPI controllers on
600 PolarFire SoC.
601 If built as a module, it will be called spi-microchip-core-qspi.
602
603config SPI_MT65XX
604 tristate "MediaTek SPI controller"
605 depends on ARCH_MEDIATEK || COMPILE_TEST
606 help
607 This selects the MediaTek(R) SPI bus driver.
608 If you want to use MediaTek(R) SPI interface,
609 say Y or M here.If you are not sure, say N.
610 SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
611
612config SPI_MT7621
613 tristate "MediaTek MT7621 SPI Controller"
614 depends on RALINK || COMPILE_TEST
615 help
616 This selects a driver for the MediaTek MT7621 SPI Controller.
617
618config SPI_MTK_NOR
619 tristate "MediaTek SPI NOR controller"
620 depends on ARCH_MEDIATEK || COMPILE_TEST
621 help
622 This enables support for SPI NOR controller found on MediaTek
623 ARM SoCs. This is a controller specifically for SPI NOR flash.
624 It can perform generic SPI transfers up to 6 bytes via generic
625 SPI interface as well as several SPI NOR specific instructions
626 via SPI MEM interface.
627
628config SPI_MTK_SNFI
629 tristate "MediaTek SPI NAND Flash Interface"
630 depends on ARCH_MEDIATEK || COMPILE_TEST
631 depends on MTD_NAND_ECC_MEDIATEK
632 help
633 This enables support for SPI-NAND mode on the MediaTek NAND
634 Flash Interface found on MediaTek ARM SoCs. This controller
635 is implemented as a SPI-MEM controller with pipelined ECC
636 capcability.
637
638config SPI_WPCM_FIU
639 tristate "Nuvoton WPCM450 Flash Interface Unit"
640 depends on ARCH_NPCM || COMPILE_TEST
641 select REGMAP
642 help
643 This enables support got the Flash Interface Unit SPI controller
644 present in the Nuvoton WPCM450 SoC.
645
646 This driver does not support generic SPI. The implementation only
647 supports the spi-mem interface.
648
649config SPI_NPCM_FIU
650 tristate "Nuvoton NPCM FLASH Interface Unit"
651 depends on ARCH_NPCM || COMPILE_TEST
652 depends on OF && HAS_IOMEM
653 help
654 This enables support for the Flash Interface Unit SPI controller
655 in master mode.
656 This driver does not support generic SPI. The implementation only
657 supports spi-mem interface.
658
659config SPI_NPCM_PSPI
660 tristate "Nuvoton NPCM PSPI Controller"
661 depends on ARCH_NPCM || COMPILE_TEST
662 help
663 This driver provides support for Nuvoton NPCM BMC
664 Peripheral SPI controller in master mode.
665
666config SPI_LANTIQ_SSC
667 tristate "Lantiq SSC SPI controller"
668 depends on LANTIQ || X86 || COMPILE_TEST
669 help
670 This driver supports the Lantiq SSC SPI controller in master
671 mode. This controller is found on Intel (former Lantiq) SoCs like
672 the Danube, Falcon, xRX200, xRX300, Lightning Mountain.
673
674config SPI_OC_TINY
675 tristate "OpenCores tiny SPI"
676 depends on GPIOLIB || COMPILE_TEST
677 select SPI_BITBANG
678 help
679 This is the driver for OpenCores tiny SPI master controller.
680
681config SPI_OCTEON
682 tristate "Cavium OCTEON SPI controller"
683 depends on CAVIUM_OCTEON_SOC
684 help
685 SPI host driver for the hardware found on some Cavium OCTEON
686 SOCs.
687
688config SPI_OMAP_UWIRE
689 tristate "OMAP1 MicroWire"
690 depends on ARCH_OMAP1 || (ARM && COMPILE_TEST)
691 select SPI_BITBANG
692 help
693 This hooks up to the MicroWire controller on OMAP1 chips.
694
695config SPI_OMAP24XX
696 tristate "McSPI driver for OMAP"
697 depends on ARCH_OMAP2PLUS || ARCH_K3 || COMPILE_TEST
698 select SG_SPLIT
699 help
700 SPI master controller for OMAP24XX and later Multichannel SPI
701 (McSPI) modules.
702
703config SPI_TI_QSPI
704 tristate "DRA7xxx QSPI controller support"
705 depends on ARCH_OMAP2PLUS || COMPILE_TEST
706 help
707 QSPI master controller for DRA7xxx used for flash devices.
708 This device supports single, dual and quad read support, while
709 it only supports single write mode.
710
711config SPI_OMAP_100K
712 tristate "OMAP SPI 100K"
713 depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
714 help
715 OMAP SPI 100K master controller for omap7xx boards.
716
717config SPI_ORION
718 tristate "Orion SPI master"
719 depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST
720 help
721 This enables using the SPI master controller on the Orion
722 and MVEBU chips.
723
724config SPI_PCI1XXXX
725 tristate "PCI1XXXX SPI Bus support"
726 depends on PCI
727 help
728 Say "yes" to Enable the SPI Bus support for the PCI1xxxx card
729 This is a PCI to SPI Bus driver
730 This driver can be built as module. If so, the module will be
731 called as spi-pci1xxxx.
732
733config SPI_PIC32
734 tristate "Microchip PIC32 series SPI"
735 depends on MACH_PIC32 || COMPILE_TEST
736 help
737 SPI driver for Microchip PIC32 SPI master controller.
738
739config SPI_PIC32_SQI
740 tristate "Microchip PIC32 Quad SPI driver"
741 depends on MACH_PIC32 || COMPILE_TEST
742 help
743 SPI driver for PIC32 Quad SPI controller.
744
745config SPI_PL022
746 tristate "ARM AMBA PL022 SSP controller"
747 depends on ARM_AMBA
748 default y if ARCH_REALVIEW
749 default y if INTEGRATOR_IMPD1
750 default y if ARCH_VERSATILE
751 help
752 This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
753 controller. If you have an embedded system with an AMBA(R)
754 bus and a PL022 controller, say Y or M here.
755
756config SPI_PPC4xx
757 tristate "PPC4xx SPI Controller"
758 depends on PPC32 && 4xx
759 select SPI_BITBANG
760 help
761 This selects a driver for the PPC4xx SPI Controller.
762
763config SPI_PXA2XX
764 tristate "PXA2xx SSP SPI master"
765 depends on ARCH_PXA || ARCH_MMP || PCI || ACPI || COMPILE_TEST
766 select PXA_SSP if ARCH_PXA || ARCH_MMP
767 help
768 This enables using a PXA2xx or Sodaville SSP port as a SPI master
769 controller. The driver can be configured to use any SSP port and
770 additional documentation can be found a Documentation/spi/pxa2xx.rst.
771
772config SPI_PXA2XX_PCI
773 def_tristate SPI_PXA2XX && PCI && COMMON_CLK
774
775config SPI_ROCKCHIP
776 tristate "Rockchip SPI controller driver"
777 help
778 This selects a driver for Rockchip SPI controller.
779
780 If you say yes to this option, support will be included for
781 RK3066, RK3188 and RK3288 families of SPI controller.
782 Rockchip SPI controller support DMA transport and PIO mode.
783 The main usecase of this controller is to use spi flash as boot
784 device.
785
786config SPI_ROCKCHIP_SFC
787 tristate "Rockchip Serial Flash Controller (SFC)"
788 depends on ARCH_ROCKCHIP || COMPILE_TEST
789 depends on HAS_IOMEM && HAS_DMA
790 help
791 This enables support for Rockchip serial flash controller. This
792 is a specialized controller used to access SPI flash on some
793 Rockchip SOCs.
794
795 ROCKCHIP SFC supports DMA and PIO modes. When DMA is not available,
796 the driver automatically falls back to PIO mode.
797
798config SPI_RB4XX
799 tristate "Mikrotik RB4XX SPI master"
800 depends on SPI_MASTER && ATH79
801 help
802 SPI controller driver for the Mikrotik RB4xx series boards.
803
804config SPI_RPCIF
805 tristate "Renesas RPC-IF SPI driver"
806 depends on RENESAS_RPCIF
807 help
808 SPI driver for Renesas R-Car Gen3 or RZ/G2 RPC-IF.
809
810config SPI_RSPI
811 tristate "Renesas RSPI/QSPI controller"
812 depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
813 help
814 SPI driver for Renesas RSPI and QSPI blocks.
815
816config SPI_QCOM_QSPI
817 tristate "QTI QSPI controller"
818 depends on ARCH_QCOM
819 help
820 QSPI(Quad SPI) driver for Qualcomm QSPI controller.
821
822config SPI_QUP
823 tristate "Qualcomm SPI controller with QUP interface"
824 depends on ARCH_QCOM || COMPILE_TEST
825 help
826 Qualcomm Universal Peripheral (QUP) core is an AHB slave that
827 provides a common data path (an output FIFO and an input FIFO)
828 for serial peripheral interface (SPI) mini-core. SPI in master
829 mode supports up to 50MHz, up to four chip selects, programmable
830 data path from 4 bits to 32 bits and numerous protocol variants.
831
832 This driver can also be built as a module. If so, the module
833 will be called spi_qup.
834
835config SPI_QCOM_GENI
836 tristate "Qualcomm GENI based SPI controller"
837 depends on QCOM_GENI_SE
838 help
839 This driver supports GENI serial engine based SPI controller in
840 master mode on the Qualcomm Technologies Inc.'s SoCs. If you say
841 yes to this option, support will be included for the built-in SPI
842 interface on the Qualcomm Technologies Inc.'s SoCs.
843
844 This driver can also be built as a module. If so, the module
845 will be called spi-geni-qcom.
846
847config SPI_S3C24XX
848 tristate "Samsung S3C24XX series SPI"
849 depends on ARCH_S3C24XX
850 select SPI_BITBANG
851 help
852 SPI driver for Samsung S3C24XX series ARM SoCs
853
854config SPI_S3C24XX_FIQ
855 bool "S3C24XX driver with FIQ pseudo-DMA"
856 depends on SPI_S3C24XX
857 select FIQ
858 help
859 Enable FIQ support for the S3C24XX SPI driver to provide pseudo
860 DMA by using the fast-interrupt request framework, This allows
861 the driver to get DMA-like performance when there are either
862 no free DMA channels, or when doing transfers that required both
863 TX and RX data paths.
864
865config SPI_S3C64XX
866 tristate "Samsung S3C64XX/Exynos SoC series type SPI"
867 depends on (PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST)
868 help
869 SPI driver for Samsung S3C64XX, S5Pv210 and Exynos SoCs.
870 Choose Y/M here only if you build for such Samsung SoC.
871
872config SPI_SC18IS602
873 tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
874 depends on I2C
875 help
876 SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
877
878config SPI_SH_MSIOF
879 tristate "SuperH MSIOF SPI controller"
880 depends on HAVE_CLK
881 depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
882 help
883 SPI driver for SuperH and SH Mobile MSIOF blocks.
884
885config SPI_SH
886 tristate "SuperH SPI controller"
887 depends on SUPERH || COMPILE_TEST
888 help
889 SPI driver for SuperH SPI blocks.
890
891config SPI_SH_SCI
892 tristate "SuperH SCI SPI controller"
893 depends on SUPERH
894 select SPI_BITBANG
895 help
896 SPI driver for SuperH SCI blocks.
897
898config SPI_SH_HSPI
899 tristate "SuperH HSPI controller"
900 depends on ARCH_RENESAS || COMPILE_TEST
901 help
902 SPI driver for SuperH HSPI blocks.
903
904config SPI_SIFIVE
905 tristate "SiFive SPI controller"
906 depends on HAS_IOMEM
907 help
908 This exposes the SPI controller IP from SiFive.
909
910config SPI_SLAVE_MT27XX
911 tristate "MediaTek SPI slave device"
912 depends on ARCH_MEDIATEK || COMPILE_TEST
913 depends on SPI_SLAVE
914 help
915 This selects the MediaTek(R) SPI slave device driver.
916 If you want to use MediaTek(R) SPI slave interface,
917 say Y or M here.If you are not sure, say N.
918 SPI slave drivers for Mediatek MT27XX series ARM SoCs.
919
920config SPI_SN_F_OSPI
921 tristate "Socionext F_OSPI SPI flash controller"
922 depends on OF && HAS_IOMEM
923 depends on SPI_MEM
924 help
925 This enables support for the Socionext F_OSPI controller
926 for connecting an SPI Flash memory over up to 8-bit wide bus.
927 It supports indirect access mode only.
928
929config SPI_SPRD
930 tristate "Spreadtrum SPI controller"
931 depends on ARCH_SPRD || COMPILE_TEST
932 help
933 SPI driver for Spreadtrum SoCs.
934
935config SPI_SPRD_ADI
936 tristate "Spreadtrum ADI controller"
937 depends on ARCH_SPRD || COMPILE_TEST
938 depends on HWSPINLOCK || (COMPILE_TEST && !HWSPINLOCK)
939 help
940 ADI driver based on SPI for Spreadtrum SoCs.
941
942config SPI_STM32
943 tristate "STMicroelectronics STM32 SPI controller"
944 depends on ARCH_STM32 || COMPILE_TEST
945 help
946 SPI driver for STMicroelectronics STM32 SoCs.
947
948 STM32 SPI controller supports DMA and PIO modes. When DMA
949 is not available, the driver automatically falls back to
950 PIO mode.
951
952config SPI_STM32_QSPI
953 tristate "STMicroelectronics STM32 QUAD SPI controller"
954 depends on ARCH_STM32 || COMPILE_TEST
955 depends on OF
956 depends on SPI_MEM
957 help
958 This enables support for the Quad SPI controller in master mode.
959 This driver does not support generic SPI. The implementation only
960 supports spi-mem interface.
961
962config SPI_ST_SSC4
963 tristate "STMicroelectronics SPI SSC-based driver"
964 depends on ARCH_STI || COMPILE_TEST
965 help
966 STMicroelectronics SoCs support for SPI. If you say yes to
967 this option, support will be included for the SSC driven SPI.
968
969config SPI_SUN4I
970 tristate "Allwinner A10 SoCs SPI controller"
971 depends on ARCH_SUNXI || COMPILE_TEST
972 help
973 SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
974
975config SPI_SUN6I
976 tristate "Allwinner A31 SPI controller"
977 depends on ARCH_SUNXI || COMPILE_TEST
978 depends on RESET_CONTROLLER
979 help
980 This enables using the SPI controller on the Allwinner A31 SoCs.
981
982config SPI_SUNPLUS_SP7021
983 tristate "Sunplus SP7021 SPI controller"
984 depends on SOC_SP7021 || COMPILE_TEST
985 help
986 This enables Sunplus SP7021 SPI controller driver on the SP7021 SoCs.
987 This driver can also be built as a module. If so, the module will be
988 called as spi-sunplus-sp7021.
989
990 If you have a Sunplus SP7021 platform say Y here.
991 If unsure, say N.
992
993config SPI_SYNQUACER
994 tristate "Socionext's SynQuacer HighSpeed SPI controller"
995 depends on ARCH_SYNQUACER || COMPILE_TEST
996 help
997 SPI driver for Socionext's High speed SPI controller which provides
998 various operating modes for interfacing to serial peripheral devices
999 that use the de-facto standard SPI protocol.
1000
1001 It also supports the new dual-bit and quad-bit SPI protocol.
1002
1003config SPI_MXIC
1004 tristate "Macronix MX25F0A SPI controller"
1005 depends on SPI_MASTER
1006 imply MTD_NAND_ECC_MXIC
1007 help
1008 This selects the Macronix MX25F0A SPI controller driver.
1009
1010config SPI_MXS
1011 tristate "Freescale MXS SPI controller"
1012 depends on ARCH_MXS
1013 select STMP_DEVICE
1014 help
1015 SPI driver for Freescale MXS devices.
1016
1017config SPI_TEGRA210_QUAD
1018 tristate "NVIDIA Tegra QSPI Controller"
1019 depends on ARCH_TEGRA || COMPILE_TEST
1020 depends on RESET_CONTROLLER
1021 help
1022 QSPI driver for NVIDIA Tegra QSPI Controller interface. This
1023 controller is different from the SPI controller and is available
1024 on Tegra SoCs starting from Tegra210.
1025
1026config SPI_TEGRA114
1027 tristate "NVIDIA Tegra114 SPI Controller"
1028 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
1029 depends on RESET_CONTROLLER
1030 help
1031 SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
1032 is different than the older SoCs SPI controller and also register interface
1033 get changed with this controller.
1034
1035config SPI_TEGRA20_SFLASH
1036 tristate "Nvidia Tegra20 Serial flash Controller"
1037 depends on ARCH_TEGRA || COMPILE_TEST
1038 depends on RESET_CONTROLLER
1039 help
1040 SPI driver for Nvidia Tegra20 Serial flash Controller interface.
1041 The main usecase of this controller is to use spi flash as boot
1042 device.
1043
1044config SPI_TEGRA20_SLINK
1045 tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
1046 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
1047 depends on RESET_CONTROLLER
1048 help
1049 SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
1050
1051config SPI_THUNDERX
1052 tristate "Cavium ThunderX SPI controller"
1053 depends on PCI && 64BIT && (ARM64 || COMPILE_TEST)
1054 help
1055 SPI host driver for the hardware found on Cavium ThunderX
1056 SOCs.
1057
1058config SPI_TOPCLIFF_PCH
1059 tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
1060 depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
1061 help
1062 SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
1063 used in some x86 embedded processors.
1064
1065 This driver also supports the ML7213/ML7223/ML7831, a companion chip
1066 for the Atom E6xx series and compatible with the Intel EG20T PCH.
1067
1068config SPI_UNIPHIER
1069 tristate "Socionext UniPhier SPI Controller"
1070 depends on (ARCH_UNIPHIER || COMPILE_TEST) && OF
1071 depends on HAS_IOMEM
1072 help
1073 This enables a driver for the Socionext UniPhier SoC SCSSI SPI controller.
1074
1075 UniPhier SoCs have SCSSI and MCSSI SPI controllers.
1076 Every UniPhier SoC has SCSSI which supports single channel.
1077 Older UniPhier Pro4/Pro5 also has MCSSI which support multiple channels.
1078 This driver supports SCSSI only.
1079
1080 If your SoC supports SCSSI, say Y here.
1081
1082config SPI_XCOMM
1083 tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
1084 depends on I2C
1085 help
1086 Support for the SPI-I2C bridge found on the Analog Devices
1087 AD-FMCOMMS1-EBZ board.
1088
1089config SPI_XILINX
1090 tristate "Xilinx SPI controller common module"
1091 depends on HAS_IOMEM
1092 select SPI_BITBANG
1093 help
1094 This exposes the SPI controller IP from the Xilinx EDK.
1095
1096 See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
1097 Product Specification document (DS464) for hardware details.
1098
1099 Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
1100
1101config SPI_XLP
1102 tristate "Cavium ThunderX2 SPI controller driver"
1103 depends on ARCH_THUNDER2 || COMPILE_TEST
1104 help
1105 Enable support for the SPI controller on the Cavium ThunderX2.
1106 (Originally on Netlogic XLP SoCs.)
1107
1108 If you have a Cavium ThunderX2 platform say Y here.
1109 If unsure, say N.
1110
1111config SPI_XTENSA_XTFPGA
1112 tristate "Xtensa SPI controller for xtfpga"
1113 depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
1114 select SPI_BITBANG
1115 help
1116 SPI driver for xtfpga SPI master controller.
1117
1118 This simple SPI master controller is built into xtfpga bitstreams
1119 and is used to control daughterboard audio codec. It always transfers
1120 16 bit words in SPI mode 0, automatically asserting CS on transfer
1121 start and deasserting on end.
1122
1123config SPI_ZYNQ_QSPI
1124 tristate "Xilinx Zynq QSPI controller"
1125 depends on ARCH_ZYNQ || COMPILE_TEST
1126 help
1127 This enables support for the Zynq Quad SPI controller
1128 in master mode.
1129 This controller only supports SPI memory interface.
1130
1131config SPI_ZYNQMP_GQSPI
1132 tristate "Xilinx ZynqMP GQSPI controller"
1133 depends on (SPI_MASTER && HAS_DMA) || COMPILE_TEST
1134 help
1135 Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
1136
1137config SPI_AMD
1138 tristate "AMD SPI controller"
1139 depends on SPI_MASTER || COMPILE_TEST
1140 help
1141 Enables SPI controller driver for AMD SoC.
1142
1143#
1144# Add new SPI master controllers in alphabetical order above this line
1145#
1146
1147comment "SPI Multiplexer support"
1148
1149config SPI_MUX
1150 tristate "SPI multiplexer support"
1151 select MULTIPLEXER
1152 help
1153 This adds support for SPI multiplexers. Each SPI mux will be
1154 accessible as a SPI controller, the devices behind the mux will appear
1155 to be chip selects on this controller. It is still necessary to
1156 select one or more specific mux-controller drivers.
1157
1158#
1159# There are lots of SPI device types, with sensors and memory
1160# being probably the most widely used ones.
1161#
1162comment "SPI Protocol Masters"
1163
1164config SPI_SPIDEV
1165 tristate "User mode SPI device driver support"
1166 help
1167 This supports user mode SPI protocol drivers.
1168
1169 Note that this application programming interface is EXPERIMENTAL
1170 and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
1171
1172config SPI_LOOPBACK_TEST
1173 tristate "spi loopback test framework support"
1174 depends on m
1175 help
1176 This enables the SPI loopback testing framework driver
1177
1178 primarily used for development of spi_master drivers
1179 and to detect regressions
1180
1181config SPI_TLE62X0
1182 tristate "Infineon TLE62X0 (for power switching)"
1183 depends on SYSFS
1184 help
1185 SPI driver for Infineon TLE62X0 series line driver chips,
1186 such as the TLE6220, TLE6230 and TLE6240. This provides a
1187 sysfs interface, with each line presented as a kind of GPIO
1188 exposing both switch control and diagnostic feedback.
1189
1190#
1191# Add new SPI protocol masters in alphabetical order above this line
1192#
1193
1194endif # SPI_MASTER
1195
1196#
1197# SLAVE side ... listening to other SPI masters
1198#
1199
1200config SPI_SLAVE
1201 bool "SPI slave protocol handlers"
1202 help
1203 If your system has a slave-capable SPI controller, you can enable
1204 slave protocol handlers.
1205
1206if SPI_SLAVE
1207
1208config SPI_SLAVE_TIME
1209 tristate "SPI slave handler reporting boot up time"
1210 help
1211 SPI slave handler responding with the time of reception of the last
1212 SPI message.
1213
1214config SPI_SLAVE_SYSTEM_CONTROL
1215 tristate "SPI slave handler controlling system state"
1216 help
1217 SPI slave handler to allow remote control of system reboot, power
1218 off, halt, and suspend.
1219
1220endif # SPI_SLAVE
1221
1222config SPI_DYNAMIC
1223 def_bool ACPI || OF_DYNAMIC || SPI_SLAVE
1224
1225endif # SPI
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# SPI driver configuration
4#
5menuconfig SPI
6 bool "SPI support"
7 depends on HAS_IOMEM
8 help
9 The "Serial Peripheral Interface" is a low level synchronous
10 protocol. Chips that support SPI can have data transfer rates
11 up to several tens of Mbit/sec. Chips are addressed with a
12 controller and a chipselect. Most SPI slaves don't support
13 dynamic device discovery; some are even write-only or read-only.
14
15 SPI is widely used by microcontrollers to talk with sensors,
16 eeprom and flash memory, codecs and various other controller
17 chips, analog to digital (and d-to-a) converters, and more.
18 MMC and SD cards can be accessed using SPI protocol; and for
19 DataFlash cards used in MMC sockets, SPI must always be used.
20
21 SPI is one of a family of similar protocols using a four wire
22 interface (select, clock, data in, data out) including Microwire
23 (half duplex), SSP, SSI, and PSP. This driver framework should
24 work with most such devices and controllers.
25
26if SPI
27
28config SPI_DEBUG
29 bool "Debug support for SPI drivers"
30 depends on DEBUG_KERNEL
31 help
32 Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
33 sysfs, and debugfs support in SPI controller and protocol drivers.
34
35#
36# MASTER side ... talking to discrete SPI slave chips including microcontrollers
37#
38
39config SPI_MASTER
40# bool "SPI Master Support"
41 bool
42 default SPI
43 help
44 If your system has an master-capable SPI controller (which
45 provides the clock and chipselect), you can enable that
46 controller and the protocol drivers for the SPI slave chips
47 that are connected.
48
49if SPI_MASTER
50
51config SPI_MEM
52 bool "SPI memory extension"
53 help
54 Enable this option if you want to enable the SPI memory extension.
55 This extension is meant to simplify interaction with SPI memories
56 by providing a high-level interface to send memory-like commands.
57
58comment "SPI Master Controller Drivers"
59
60config SPI_ALTERA
61 tristate "Altera SPI Controller"
62 help
63 This is the driver for the Altera SPI Controller.
64
65config SPI_ATH79
66 tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
67 depends on ATH79 || COMPILE_TEST
68 select SPI_BITBANG
69 help
70 This enables support for the SPI controller present on the
71 Atheros AR71XX/AR724X/AR913X SoCs.
72
73config SPI_ARMADA_3700
74 tristate "Marvell Armada 3700 SPI Controller"
75 depends on (ARCH_MVEBU && OF) || COMPILE_TEST
76 help
77 This enables support for the SPI controller present on the
78 Marvell Armada 3700 SoCs.
79
80config SPI_ATMEL
81 tristate "Atmel SPI Controller"
82 depends on ARCH_AT91 || COMPILE_TEST
83 help
84 This selects a driver for the Atmel SPI Controller, present on
85 many AT91 ARM chips.
86
87config SPI_AT91_USART
88 tristate "Atmel USART Controller SPI driver"
89 depends on (ARCH_AT91 || COMPILE_TEST)
90 depends on MFD_AT91_USART
91 help
92 This selects a driver for the AT91 USART Controller as SPI Master,
93 present on AT91 and SAMA5 SoC series.
94
95config SPI_ATMEL_QUADSPI
96 tristate "Atmel Quad SPI Controller"
97 depends on ARCH_AT91 || (ARM && COMPILE_TEST && !ARCH_EBSA110)
98 depends on OF && HAS_IOMEM
99 help
100 This enables support for the Quad SPI controller in master mode.
101 This driver does not support generic SPI. The implementation only
102 supports spi-mem interface.
103
104config SPI_AU1550
105 tristate "Au1550/Au1200/Au1300 SPI Controller"
106 depends on MIPS_ALCHEMY
107 select SPI_BITBANG
108 help
109 If you say yes to this option, support will be included for the
110 PSC SPI controller found on Au1550, Au1200 and Au1300 series.
111
112config SPI_AXI_SPI_ENGINE
113 tristate "Analog Devices AXI SPI Engine controller"
114 depends on HAS_IOMEM
115 help
116 This enables support for the Analog Devices AXI SPI Engine SPI controller.
117 It is part of the SPI Engine framework that is used in some Analog Devices
118 reference designs for FPGAs.
119
120config SPI_BCM2835
121 tristate "BCM2835 SPI controller"
122 depends on GPIOLIB
123 depends on ARCH_BCM2835 || ARCH_BRCMSTB || COMPILE_TEST
124 help
125 This selects a driver for the Broadcom BCM2835 SPI master.
126
127 The BCM2835 contains two types of SPI master controller; the
128 "universal SPI master", and the regular SPI controller. This driver
129 is for the regular SPI controller. Slave mode operation is not also
130 not supported.
131
132config SPI_BCM2835AUX
133 tristate "BCM2835 SPI auxiliary controller"
134 depends on ((ARCH_BCM2835 || ARCH_BRCMSTB) && GPIOLIB) || COMPILE_TEST
135 help
136 This selects a driver for the Broadcom BCM2835 SPI aux master.
137
138 The BCM2835 contains two types of SPI master controller; the
139 "universal SPI master", and the regular SPI controller.
140 This driver is for the universal/auxiliary SPI controller.
141
142config SPI_BCM63XX
143 tristate "Broadcom BCM63xx SPI controller"
144 depends on BCM63XX || COMPILE_TEST
145 help
146 Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
147
148config SPI_BCM63XX_HSSPI
149 tristate "Broadcom BCM63XX HS SPI controller driver"
150 depends on BCM63XX || ARCH_BCM_63XX || COMPILE_TEST
151 help
152 This enables support for the High Speed SPI controller present on
153 newer Broadcom BCM63XX SoCs.
154
155config SPI_BCM_QSPI
156 tristate "Broadcom BSPI and MSPI controller support"
157 depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || \
158 BMIPS_GENERIC || COMPILE_TEST
159 default ARCH_BCM_IPROC
160 help
161 Enables support for the Broadcom SPI flash and MSPI controller.
162 Select this option for any one of BRCMSTB, iProc NSP and NS2 SoCs
163 based platforms. This driver works for both SPI master for spi-nor
164 flash device as well as MSPI device.
165
166config SPI_BITBANG
167 tristate "Utilities for Bitbanging SPI masters"
168 help
169 With a few GPIO pins, your system can bitbang the SPI protocol.
170 Select this to get SPI support through I/O pins (GPIO, parallel
171 port, etc). Or, some systems' SPI master controller drivers use
172 this code to manage the per-word or per-transfer accesses to the
173 hardware shift registers.
174
175 This is library code, and is automatically selected by drivers that
176 need it. You only need to select this explicitly to support driver
177 modules that aren't part of this kernel tree.
178
179config SPI_BUTTERFLY
180 tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
181 depends on PARPORT
182 select SPI_BITBANG
183 help
184 This uses a custom parallel port cable to connect to an AVR
185 Butterfly <http://www.atmel.com/products/avr/butterfly>, an
186 inexpensive battery powered microcontroller evaluation board.
187 This same cable can be used to flash new firmware.
188
189config SPI_CADENCE
190 tristate "Cadence SPI controller"
191 help
192 This selects the Cadence SPI controller master driver
193 used by Xilinx Zynq and ZynqMP.
194
195config SPI_CLPS711X
196 tristate "CLPS711X host SPI controller"
197 depends on ARCH_CLPS711X || COMPILE_TEST
198 help
199 This enables dedicated general purpose SPI/Microwire1-compatible
200 master mode interface (SSI1) for CLPS711X-based CPUs.
201
202config SPI_COLDFIRE_QSPI
203 tristate "Freescale Coldfire QSPI controller"
204 depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
205 help
206 This enables support for the Coldfire QSPI controller in master
207 mode.
208
209config SPI_DAVINCI
210 tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
211 depends on ARCH_DAVINCI || ARCH_KEYSTONE
212 select SPI_BITBANG
213 help
214 SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
215
216config SPI_DESIGNWARE
217 tristate "DesignWare SPI controller core support"
218 help
219 general driver for SPI controller core from DesignWare
220
221config SPI_DW_PCI
222 tristate "PCI interface driver for DW SPI core"
223 depends on SPI_DESIGNWARE && PCI
224
225config SPI_DW_MID_DMA
226 bool "DMA support for DW SPI controller on Intel MID platform"
227 depends on SPI_DW_PCI && DW_DMAC_PCI
228
229config SPI_DW_MMIO
230 tristate "Memory-mapped io interface driver for DW SPI core"
231 depends on SPI_DESIGNWARE
232
233config SPI_DLN2
234 tristate "Diolan DLN-2 USB SPI adapter"
235 depends on MFD_DLN2
236 help
237 If you say yes to this option, support will be included for Diolan
238 DLN2, a USB to SPI interface.
239
240 This driver can also be built as a module. If so, the module
241 will be called spi-dln2.
242
243config SPI_EFM32
244 tristate "EFM32 SPI controller"
245 depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST)
246 select SPI_BITBANG
247 help
248 Driver for the spi controller found on Energy Micro's EFM32 SoCs.
249
250config SPI_EP93XX
251 tristate "Cirrus Logic EP93xx SPI controller"
252 depends on ARCH_EP93XX || COMPILE_TEST
253 help
254 This enables using the Cirrus EP93xx SPI controller in master
255 mode.
256
257config SPI_FALCON
258 bool "Falcon SPI controller support"
259 depends on SOC_FALCON
260 help
261 The external bus unit (EBU) found on the FALC-ON SoC has SPI
262 emulation that is designed for serial flash access. This driver
263 has only been tested with m25p80 type chips. The hardware has no
264 support for other types of SPI peripherals.
265
266config SPI_FSL_LPSPI
267 tristate "Freescale i.MX LPSPI controller"
268 depends on ARCH_MXC || COMPILE_TEST
269 help
270 This enables Freescale i.MX LPSPI controllers in master mode.
271
272config SPI_FSL_QUADSPI
273 tristate "Freescale QSPI controller"
274 depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
275 depends on HAS_IOMEM
276 help
277 This enables support for the Quad SPI controller in master mode.
278 Up to four flash chips can be connected on two buses with two
279 chipselects each.
280 This controller does not support generic SPI messages. It only
281 supports the high-level SPI memory interface.
282
283config SPI_NXP_FLEXSPI
284 tristate "NXP Flex SPI controller"
285 depends on ARCH_LAYERSCAPE || HAS_IOMEM
286 help
287 This enables support for the Flex SPI controller in master mode.
288 Up to four slave devices can be connected on two buses with two
289 chipselects each.
290 This controller does not support generic SPI messages and only
291 supports the high-level SPI memory interface.
292
293config SPI_GPIO
294 tristate "GPIO-based bitbanging SPI Master"
295 depends on GPIOLIB || COMPILE_TEST
296 select SPI_BITBANG
297 help
298 This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
299 interface to manage MOSI, MISO, SCK, and chipselect signals. SPI
300 slaves connected to a bus using this driver are configured as usual,
301 except that the spi_board_info.controller_data holds the GPIO number
302 for the chipselect used by this controller driver.
303
304 Note that this driver often won't achieve even 1 Mbit/sec speeds,
305 making it unusually slow for SPI. If your platform can inline
306 GPIO operations, you should be able to leverage that for better
307 speed with a custom version of this driver; see the source code.
308
309config SPI_IMG_SPFI
310 tristate "IMG SPFI controller"
311 depends on MIPS || COMPILE_TEST
312 help
313 This enables support for the SPFI master controller found on
314 IMG SoCs.
315
316config SPI_IMX
317 tristate "Freescale i.MX SPI controllers"
318 depends on ARCH_MXC || COMPILE_TEST
319 select SPI_BITBANG
320 help
321 This enables support for the Freescale i.MX SPI controllers.
322
323config SPI_JCORE
324 tristate "J-Core SPI Master"
325 depends on OF && (SUPERH || COMPILE_TEST)
326 help
327 This enables support for the SPI master controller in the J-Core
328 synthesizable, open source SoC.
329
330config SPI_LM70_LLP
331 tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
332 depends on PARPORT
333 select SPI_BITBANG
334 help
335 This driver supports the NS LM70 LLP Evaluation Board,
336 which interfaces to an LM70 temperature sensor using
337 a parallel port.
338
339config SPI_LP8841_RTC
340 tristate "ICP DAS LP-8841 SPI Controller for RTC"
341 depends on MACH_PXA27X_DT || COMPILE_TEST
342 help
343 This driver provides an SPI master device to drive Maxim
344 DS-1302 real time clock.
345
346 Say N here unless you plan to run the kernel on an ICP DAS
347 LP-8x4x industrial computer.
348
349config SPI_MPC52xx
350 tristate "Freescale MPC52xx SPI (non-PSC) controller support"
351 depends on PPC_MPC52xx
352 help
353 This drivers supports the MPC52xx SPI controller in master SPI
354 mode.
355
356config SPI_MPC52xx_PSC
357 tristate "Freescale MPC52xx PSC SPI controller"
358 depends on PPC_MPC52xx
359 help
360 This enables using the Freescale MPC52xx Programmable Serial
361 Controller in master SPI mode.
362
363config SPI_MPC512x_PSC
364 tristate "Freescale MPC512x PSC SPI controller"
365 depends on PPC_MPC512x
366 help
367 This enables using the Freescale MPC5121 Programmable Serial
368 Controller in SPI master mode.
369
370config SPI_FSL_LIB
371 tristate
372 depends on OF
373
374config SPI_FSL_CPM
375 tristate
376 depends on FSL_SOC
377
378config SPI_FSL_SPI
379 tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
380 depends on OF
381 select SPI_FSL_LIB
382 select SPI_FSL_CPM if FSL_SOC
383 help
384 This enables using the Freescale SPI controllers in master mode.
385 MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
386 MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
387 This also enables using the Aeroflex Gaisler GRLIB SPI controller in
388 master mode.
389
390config SPI_FSL_DSPI
391 tristate "Freescale DSPI controller"
392 select REGMAP_MMIO
393 depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || M5441x || COMPILE_TEST
394 help
395 This enables support for the Freescale DSPI controller in master
396 mode. VF610, LS1021A and ColdFire platforms uses the controller.
397
398config SPI_FSL_ESPI
399 tristate "Freescale eSPI controller"
400 depends on FSL_SOC
401 help
402 This enables using the Freescale eSPI controllers in master mode.
403 From MPC8536, 85xx platform uses the controller, and all P10xx,
404 P20xx, P30xx,P40xx, P50xx uses this controller.
405
406config SPI_MESON_SPICC
407 tristate "Amlogic Meson SPICC controller"
408 depends on ARCH_MESON || COMPILE_TEST
409 help
410 This enables master mode support for the SPICC (SPI communication
411 controller) available in Amlogic Meson SoCs.
412
413config SPI_MESON_SPIFC
414 tristate "Amlogic Meson SPIFC controller"
415 depends on ARCH_MESON || COMPILE_TEST
416 select REGMAP_MMIO
417 help
418 This enables master mode support for the SPIFC (SPI flash
419 controller) available in Amlogic Meson SoCs.
420
421config SPI_MT65XX
422 tristate "MediaTek SPI controller"
423 depends on ARCH_MEDIATEK || COMPILE_TEST
424 help
425 This selects the MediaTek(R) SPI bus driver.
426 If you want to use MediaTek(R) SPI interface,
427 say Y or M here.If you are not sure, say N.
428 SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
429
430config SPI_MT7621
431 tristate "MediaTek MT7621 SPI Controller"
432 depends on RALINK || COMPILE_TEST
433 help
434 This selects a driver for the MediaTek MT7621 SPI Controller.
435
436config SPI_NPCM_FIU
437 tristate "Nuvoton NPCM FLASH Interface Unit"
438 depends on ARCH_NPCM || COMPILE_TEST
439 depends on OF && HAS_IOMEM
440 help
441 This enables support for the Flash Interface Unit SPI controller
442 in master mode.
443 This driver does not support generic SPI. The implementation only
444 supports spi-mem interface.
445
446config SPI_NPCM_PSPI
447 tristate "Nuvoton NPCM PSPI Controller"
448 depends on ARCH_NPCM || COMPILE_TEST
449 help
450 This driver provides support for Nuvoton NPCM BMC
451 Peripheral SPI controller in master mode.
452
453config SPI_LANTIQ_SSC
454 tristate "Lantiq SSC SPI controller"
455 depends on LANTIQ || COMPILE_TEST
456 help
457 This driver supports the Lantiq SSC SPI controller in master
458 mode. This controller is found on Intel (former Lantiq) SoCs like
459 the Danube, Falcon, xRX200, xRX300.
460
461config SPI_OC_TINY
462 tristate "OpenCores tiny SPI"
463 depends on GPIOLIB || COMPILE_TEST
464 select SPI_BITBANG
465 help
466 This is the driver for OpenCores tiny SPI master controller.
467
468config SPI_OCTEON
469 tristate "Cavium OCTEON SPI controller"
470 depends on CAVIUM_OCTEON_SOC
471 help
472 SPI host driver for the hardware found on some Cavium OCTEON
473 SOCs.
474
475config SPI_OMAP_UWIRE
476 tristate "OMAP1 MicroWire"
477 depends on ARCH_OMAP1
478 select SPI_BITBANG
479 help
480 This hooks up to the MicroWire controller on OMAP1 chips.
481
482config SPI_OMAP24XX
483 tristate "McSPI driver for OMAP"
484 depends on ARCH_OMAP2PLUS || ARCH_K3 || COMPILE_TEST
485 select SG_SPLIT
486 help
487 SPI master controller for OMAP24XX and later Multichannel SPI
488 (McSPI) modules.
489
490config SPI_TI_QSPI
491 tristate "DRA7xxx QSPI controller support"
492 depends on ARCH_OMAP2PLUS || COMPILE_TEST
493 help
494 QSPI master controller for DRA7xxx used for flash devices.
495 This device supports single, dual and quad read support, while
496 it only supports single write mode.
497
498config SPI_OMAP_100K
499 tristate "OMAP SPI 100K"
500 depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
501 help
502 OMAP SPI 100K master controller for omap7xx boards.
503
504config SPI_ORION
505 tristate "Orion SPI master"
506 depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST
507 help
508 This enables using the SPI master controller on the Orion
509 and MVEBU chips.
510
511config SPI_PIC32
512 tristate "Microchip PIC32 series SPI"
513 depends on MACH_PIC32 || COMPILE_TEST
514 help
515 SPI driver for Microchip PIC32 SPI master controller.
516
517config SPI_PIC32_SQI
518 tristate "Microchip PIC32 Quad SPI driver"
519 depends on MACH_PIC32 || COMPILE_TEST
520 help
521 SPI driver for PIC32 Quad SPI controller.
522
523config SPI_PL022
524 tristate "ARM AMBA PL022 SSP controller"
525 depends on ARM_AMBA
526 default y if MACH_U300
527 default y if ARCH_REALVIEW
528 default y if INTEGRATOR_IMPD1
529 default y if ARCH_VERSATILE
530 help
531 This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
532 controller. If you have an embedded system with an AMBA(R)
533 bus and a PL022 controller, say Y or M here.
534
535config SPI_PPC4xx
536 tristate "PPC4xx SPI Controller"
537 depends on PPC32 && 4xx
538 select SPI_BITBANG
539 help
540 This selects a driver for the PPC4xx SPI Controller.
541
542config SPI_PXA2XX
543 tristate "PXA2xx SSP SPI master"
544 depends on (ARCH_PXA || ARCH_MMP || PCI || ACPI)
545 select PXA_SSP if ARCH_PXA || ARCH_MMP
546 help
547 This enables using a PXA2xx or Sodaville SSP port as a SPI master
548 controller. The driver can be configured to use any SSP port and
549 additional documentation can be found a Documentation/spi/pxa2xx.rst.
550
551config SPI_PXA2XX_PCI
552 def_tristate SPI_PXA2XX && PCI && COMMON_CLK
553
554config SPI_ROCKCHIP
555 tristate "Rockchip SPI controller driver"
556 help
557 This selects a driver for Rockchip SPI controller.
558
559 If you say yes to this option, support will be included for
560 RK3066, RK3188 and RK3288 families of SPI controller.
561 Rockchip SPI controller support DMA transport and PIO mode.
562 The main usecase of this controller is to use spi flash as boot
563 device.
564
565config SPI_RB4XX
566 tristate "Mikrotik RB4XX SPI master"
567 depends on SPI_MASTER && ATH79
568 help
569 SPI controller driver for the Mikrotik RB4xx series boards.
570
571config SPI_RSPI
572 tristate "Renesas RSPI/QSPI controller"
573 depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
574 help
575 SPI driver for Renesas RSPI and QSPI blocks.
576
577config SPI_QCOM_QSPI
578 tristate "QTI QSPI controller"
579 depends on ARCH_QCOM
580 help
581 QSPI(Quad SPI) driver for Qualcomm QSPI controller.
582
583config SPI_QUP
584 tristate "Qualcomm SPI controller with QUP interface"
585 depends on ARCH_QCOM || (ARM && COMPILE_TEST)
586 help
587 Qualcomm Universal Peripheral (QUP) core is an AHB slave that
588 provides a common data path (an output FIFO and an input FIFO)
589 for serial peripheral interface (SPI) mini-core. SPI in master
590 mode supports up to 50MHz, up to four chip selects, programmable
591 data path from 4 bits to 32 bits and numerous protocol variants.
592
593 This driver can also be built as a module. If so, the module
594 will be called spi_qup.
595
596config SPI_QCOM_GENI
597 tristate "Qualcomm GENI based SPI controller"
598 depends on QCOM_GENI_SE
599 help
600 This driver supports GENI serial engine based SPI controller in
601 master mode on the Qualcomm Technologies Inc.'s SoCs. If you say
602 yes to this option, support will be included for the built-in SPI
603 interface on the Qualcomm Technologies Inc.'s SoCs.
604
605 This driver can also be built as a module. If so, the module
606 will be called spi-geni-qcom.
607
608config SPI_S3C24XX
609 tristate "Samsung S3C24XX series SPI"
610 depends on ARCH_S3C24XX
611 select SPI_BITBANG
612 help
613 SPI driver for Samsung S3C24XX series ARM SoCs
614
615config SPI_S3C24XX_FIQ
616 bool "S3C24XX driver with FIQ pseudo-DMA"
617 depends on SPI_S3C24XX
618 select FIQ
619 help
620 Enable FIQ support for the S3C24XX SPI driver to provide pseudo
621 DMA by using the fast-interrupt request framework, This allows
622 the driver to get DMA-like performance when there are either
623 no free DMA channels, or when doing transfers that required both
624 TX and RX data paths.
625
626config SPI_S3C64XX
627 tristate "Samsung S3C64XX series type SPI"
628 depends on (PLAT_SAMSUNG || ARCH_EXYNOS || COMPILE_TEST)
629 help
630 SPI driver for Samsung S3C64XX and newer SoCs.
631
632config SPI_SC18IS602
633 tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
634 depends on I2C
635 help
636 SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
637
638config SPI_SH_MSIOF
639 tristate "SuperH MSIOF SPI controller"
640 depends on HAVE_CLK
641 depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
642 help
643 SPI driver for SuperH and SH Mobile MSIOF blocks.
644
645config SPI_SH
646 tristate "SuperH SPI controller"
647 depends on SUPERH || COMPILE_TEST
648 help
649 SPI driver for SuperH SPI blocks.
650
651config SPI_SH_SCI
652 tristate "SuperH SCI SPI controller"
653 depends on SUPERH
654 select SPI_BITBANG
655 help
656 SPI driver for SuperH SCI blocks.
657
658config SPI_SH_HSPI
659 tristate "SuperH HSPI controller"
660 depends on ARCH_RENESAS || COMPILE_TEST
661 help
662 SPI driver for SuperH HSPI blocks.
663
664config SPI_SIFIVE
665 tristate "SiFive SPI controller"
666 depends on HAS_IOMEM
667 help
668 This exposes the SPI controller IP from SiFive.
669
670config SPI_SIRF
671 tristate "CSR SiRFprimaII SPI controller"
672 depends on SIRF_DMA
673 select SPI_BITBANG
674 help
675 SPI driver for CSR SiRFprimaII SoCs
676
677config SPI_SLAVE_MT27XX
678 tristate "MediaTek SPI slave device"
679 depends on ARCH_MEDIATEK || COMPILE_TEST
680 depends on SPI_SLAVE
681 help
682 This selects the MediaTek(R) SPI slave device driver.
683 If you want to use MediaTek(R) SPI slave interface,
684 say Y or M here.If you are not sure, say N.
685 SPI slave drivers for Mediatek MT27XX series ARM SoCs.
686
687config SPI_SPRD
688 tristate "Spreadtrum SPI controller"
689 depends on ARCH_SPRD || COMPILE_TEST
690 help
691 SPI driver for Spreadtrum SoCs.
692
693config SPI_SPRD_ADI
694 tristate "Spreadtrum ADI controller"
695 depends on ARCH_SPRD || COMPILE_TEST
696 depends on HWSPINLOCK || (COMPILE_TEST && !HWSPINLOCK)
697 help
698 ADI driver based on SPI for Spreadtrum SoCs.
699
700config SPI_STM32
701 tristate "STMicroelectronics STM32 SPI controller"
702 depends on ARCH_STM32 || COMPILE_TEST
703 help
704 SPI driver for STMicroelectronics STM32 SoCs.
705
706 STM32 SPI controller supports DMA and PIO modes. When DMA
707 is not available, the driver automatically falls back to
708 PIO mode.
709
710config SPI_STM32_QSPI
711 tristate "STMicroelectronics STM32 QUAD SPI controller"
712 depends on ARCH_STM32 || COMPILE_TEST
713 depends on OF
714 help
715 This enables support for the Quad SPI controller in master mode.
716 This driver does not support generic SPI. The implementation only
717 supports spi-mem interface.
718
719config SPI_ST_SSC4
720 tristate "STMicroelectronics SPI SSC-based driver"
721 depends on ARCH_STI || COMPILE_TEST
722 help
723 STMicroelectronics SoCs support for SPI. If you say yes to
724 this option, support will be included for the SSC driven SPI.
725
726config SPI_SUN4I
727 tristate "Allwinner A10 SoCs SPI controller"
728 depends on ARCH_SUNXI || COMPILE_TEST
729 help
730 SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
731
732config SPI_SUN6I
733 tristate "Allwinner A31 SPI controller"
734 depends on ARCH_SUNXI || COMPILE_TEST
735 depends on RESET_CONTROLLER
736 help
737 This enables using the SPI controller on the Allwinner A31 SoCs.
738
739config SPI_SYNQUACER
740 tristate "Socionext's SynQuacer HighSpeed SPI controller"
741 depends on ARCH_SYNQUACER || COMPILE_TEST
742 help
743 SPI driver for Socionext's High speed SPI controller which provides
744 various operating modes for interfacing to serial peripheral devices
745 that use the de-facto standard SPI protocol.
746
747 It also supports the new dual-bit and quad-bit SPI protocol.
748
749config SPI_MXIC
750 tristate "Macronix MX25F0A SPI controller"
751 depends on SPI_MASTER
752 help
753 This selects the Macronix MX25F0A SPI controller driver.
754
755config SPI_MXS
756 tristate "Freescale MXS SPI controller"
757 depends on ARCH_MXS
758 select STMP_DEVICE
759 help
760 SPI driver for Freescale MXS devices.
761
762config SPI_TEGRA114
763 tristate "NVIDIA Tegra114 SPI Controller"
764 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
765 depends on RESET_CONTROLLER
766 help
767 SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
768 is different than the older SoCs SPI controller and also register interface
769 get changed with this controller.
770
771config SPI_TEGRA20_SFLASH
772 tristate "Nvidia Tegra20 Serial flash Controller"
773 depends on ARCH_TEGRA || COMPILE_TEST
774 depends on RESET_CONTROLLER
775 help
776 SPI driver for Nvidia Tegra20 Serial flash Controller interface.
777 The main usecase of this controller is to use spi flash as boot
778 device.
779
780config SPI_TEGRA20_SLINK
781 tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
782 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
783 depends on RESET_CONTROLLER
784 help
785 SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
786
787config SPI_THUNDERX
788 tristate "Cavium ThunderX SPI controller"
789 depends on PCI && 64BIT && (ARM64 || COMPILE_TEST)
790 help
791 SPI host driver for the hardware found on Cavium ThunderX
792 SOCs.
793
794config SPI_TOPCLIFF_PCH
795 tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
796 depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
797 help
798 SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
799 used in some x86 embedded processors.
800
801 This driver also supports the ML7213/ML7223/ML7831, a companion chip
802 for the Atom E6xx series and compatible with the Intel EG20T PCH.
803
804config SPI_TXX9
805 tristate "Toshiba TXx9 SPI controller"
806 depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST)
807 help
808 SPI driver for Toshiba TXx9 MIPS SoCs
809
810config SPI_UNIPHIER
811 tristate "Socionext UniPhier SPI Controller"
812 depends on (ARCH_UNIPHIER || COMPILE_TEST) && OF
813 help
814 This enables a driver for the Socionext UniPhier SoC SCSSI SPI controller.
815
816 UniPhier SoCs have SCSSI and MCSSI SPI controllers.
817 Every UniPhier SoC has SCSSI which supports single channel.
818 Older UniPhier Pro4/Pro5 also has MCSSI which support multiple channels.
819 This driver supports SCSSI only.
820
821 If your SoC supports SCSSI, say Y here.
822
823config SPI_XCOMM
824 tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
825 depends on I2C
826 help
827 Support for the SPI-I2C bridge found on the Analog Devices
828 AD-FMCOMMS1-EBZ board.
829
830config SPI_XILINX
831 tristate "Xilinx SPI controller common module"
832 depends on HAS_IOMEM
833 select SPI_BITBANG
834 help
835 This exposes the SPI controller IP from the Xilinx EDK.
836
837 See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
838 Product Specification document (DS464) for hardware details.
839
840 Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
841
842config SPI_XLP
843 tristate "Netlogic XLP SPI controller driver"
844 depends on CPU_XLP || ARCH_THUNDER2 || COMPILE_TEST
845 help
846 Enable support for the SPI controller on the Netlogic XLP SoCs.
847 Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX
848 and XLP5XX.
849
850 If you have a Netlogic XLP platform say Y here.
851 If unsure, say N.
852
853config SPI_XTENSA_XTFPGA
854 tristate "Xtensa SPI controller for xtfpga"
855 depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
856 select SPI_BITBANG
857 help
858 SPI driver for xtfpga SPI master controller.
859
860 This simple SPI master controller is built into xtfpga bitstreams
861 and is used to control daughterboard audio codec. It always transfers
862 16 bit words in SPI mode 0, automatically asserting CS on transfer
863 start and deasserting on end.
864
865config SPI_ZYNQ_QSPI
866 tristate "Xilinx Zynq QSPI controller"
867 depends on ARCH_ZYNQ || COMPILE_TEST
868 help
869 This enables support for the Zynq Quad SPI controller
870 in master mode.
871 This controller only supports SPI memory interface.
872
873config SPI_ZYNQMP_GQSPI
874 tristate "Xilinx ZynqMP GQSPI controller"
875 depends on (SPI_MASTER && HAS_DMA) || COMPILE_TEST
876 help
877 Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
878
879#
880# Add new SPI master controllers in alphabetical order above this line
881#
882
883#
884# There are lots of SPI device types, with sensors and memory
885# being probably the most widely used ones.
886#
887comment "SPI Protocol Masters"
888
889config SPI_SPIDEV
890 tristate "User mode SPI device driver support"
891 help
892 This supports user mode SPI protocol drivers.
893
894 Note that this application programming interface is EXPERIMENTAL
895 and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
896
897config SPI_LOOPBACK_TEST
898 tristate "spi loopback test framework support"
899 depends on m
900 help
901 This enables the SPI loopback testing framework driver
902
903 primarily used for development of spi_master drivers
904 and to detect regressions
905
906config SPI_TLE62X0
907 tristate "Infineon TLE62X0 (for power switching)"
908 depends on SYSFS
909 help
910 SPI driver for Infineon TLE62X0 series line driver chips,
911 such as the TLE6220, TLE6230 and TLE6240. This provides a
912 sysfs interface, with each line presented as a kind of GPIO
913 exposing both switch control and diagnostic feedback.
914
915#
916# Add new SPI protocol masters in alphabetical order above this line
917#
918
919endif # SPI_MASTER
920
921#
922# SLAVE side ... listening to other SPI masters
923#
924
925config SPI_SLAVE
926 bool "SPI slave protocol handlers"
927 help
928 If your system has a slave-capable SPI controller, you can enable
929 slave protocol handlers.
930
931if SPI_SLAVE
932
933config SPI_SLAVE_TIME
934 tristate "SPI slave handler reporting boot up time"
935 help
936 SPI slave handler responding with the time of reception of the last
937 SPI message.
938
939config SPI_SLAVE_SYSTEM_CONTROL
940 tristate "SPI slave handler controlling system state"
941 help
942 SPI slave handler to allow remote control of system reboot, power
943 off, halt, and suspend.
944
945endif # SPI_SLAVE
946
947endif # SPI