Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2
3#include <dt-bindings/input/input.h>
4
5/ {
6 cpus {
7 cpu@0 {
8 cpu0-supply = <&vcc>;
9 };
10 };
11
12 memory@80000000 {
13 device_type = "memory";
14 reg = <0x80000000 0>;
15 };
16
17 wl12xx_vmmc: wl12xx_vmmc {
18 compatible = "regulator-fixed";
19 regulator-name = "vwl1271";
20 regulator-min-microvolt = <1800000>;
21 regulator-max-microvolt = <1800000>;
22 gpio = <&gpio1 3 0>; /* gpio_3 */
23 startup-delay-us = <70000>;
24 enable-active-high;
25 vin-supply = <&vaux3>;
26 };
27
28 /* HS USB Host PHY on PORT 1 */
29 hsusb2_phy: hsusb2_phy {
30 pinctrl-names = "default";
31 pinctrl-0 = <&hsusb2_reset_pin>;
32 compatible = "usb-nop-xceiv";
33 reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
34 #phy-cells = <0>;
35 };
36
37 /* fixed 26MHz oscillator */
38 hfclk_26m: oscillator {
39 #clock-cells = <0>;
40 compatible = "fixed-clock";
41 clock-frequency = <26000000>;
42 };
43};
44
45&gpmc {
46 ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
47
48 nand@0,0 {
49 compatible = "ti,omap2-nand";
50 reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
51 interrupt-parent = <&gpmc>;
52 interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
53 <1 IRQ_TYPE_NONE>; /* termcount */
54 linux,mtd-name = "micron,mt29f4g16abbda3w";
55 nand-bus-width = <16>;
56 ti,nand-ecc-opt = "bch8";
57 rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
58 gpmc,sync-clk-ps = <0>;
59 gpmc,cs-on-ns = <0>;
60 gpmc,cs-rd-off-ns = <44>;
61 gpmc,cs-wr-off-ns = <44>;
62 gpmc,adv-on-ns = <6>;
63 gpmc,adv-rd-off-ns = <34>;
64 gpmc,adv-wr-off-ns = <44>;
65 gpmc,we-off-ns = <40>;
66 gpmc,oe-off-ns = <54>;
67 gpmc,access-ns = <64>;
68 gpmc,rd-cycle-ns = <82>;
69 gpmc,wr-cycle-ns = <82>;
70 gpmc,wr-access-ns = <40>;
71 gpmc,wr-data-mux-bus-ns = <0>;
72 gpmc,device-width = <2>;
73 #address-cells = <1>;
74 #size-cells = <1>;
75 };
76};
77
78&i2c1 {
79 pinctrl-names = "default";
80 pinctrl-0 = <&i2c1_pins>;
81 clock-frequency = <2600000>;
82
83 twl: twl@48 {
84 reg = <0x48>;
85 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
86 interrupt-parent = <&intc>;
87 clocks = <&hfclk_26m>;
88 clock-names = "fck";
89 twl_audio: audio {
90 compatible = "ti,twl4030-audio";
91 codec {
92 ti,hs_extmute_gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
93 };
94 };
95 };
96};
97
98&i2c2 {
99 pinctrl-names = "default";
100 pinctrl-0 = <&i2c2_pins>;
101 clock-frequency = <400000>;
102};
103
104&i2c3 {
105 pinctrl-names = "default";
106 pinctrl-0 = <&i2c3_pins>;
107 clock-frequency = <400000>;
108
109 touchscreen: tsc2004@48 {
110 compatible = "ti,tsc2004";
111 reg = <0x48>;
112 vio-supply = <&vaux1>;
113 pinctrl-names = "default";
114 pinctrl-0 = <&tsc2004_pins>;
115 interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */
116
117 touchscreen-fuzz-x = <4>;
118 touchscreen-fuzz-y = <7>;
119 touchscreen-fuzz-pressure = <2>;
120 touchscreen-size-x = <4096>;
121 touchscreen-size-y = <4096>;
122 touchscreen-max-pressure = <2048>;
123
124 ti,x-plate-ohms = <280>;
125 ti,esd-recovery-timeout-ms = <8000>;
126 };
127};
128
129&mmc3 {
130 interrupts-extended = <&intc 94 &omap3_pmx_core 0x136>;
131 pinctrl-0 = <&mmc3_pins &wl127x_gpio>;
132 pinctrl-names = "default";
133 vmmc-supply = <&wl12xx_vmmc>;
134 non-removable;
135 bus-width = <4>;
136 cap-power-off-card;
137 #address-cells = <1>;
138 #size-cells = <0>;
139 wlcore: wlcore@2 {
140 compatible = "ti,wl1273";
141 reg = <2>;
142 interrupt-parent = <&gpio1>;
143 interrupts = <2 IRQ_TYPE_EDGE_RISING>; /* gpio 2 */
144 ref-clock-frequency = <26000000>;
145 };
146};
147
148&usbhshost {
149 pinctrl-names = "default";
150 pinctrl-0 = <&hsusb2_pins>;
151 port2-mode = "ehci-phy";
152};
153
154&usbhsehci {
155 phys = <0 &hsusb2_phy>;
156};
157
158&omap3_pmx_core {
159
160 mmc3_pins: pinmux_mm3_pins {
161 pinctrl-single,pins = <
162 OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
163 OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
164 OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
165 OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
166 OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
167 OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */
168 >;
169 };
170 mcbsp2_pins: pinmux_mcbsp2_pins {
171 pinctrl-single,pins = <
172 OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */
173 OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */
174 OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */
175 OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */
176 >;
177 };
178 uart2_pins: pinmux_uart2_pins {
179 pinctrl-single,pins = <
180 OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */
181 OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/
182 OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
183 OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
184 OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */
185 >;
186 };
187 mcspi1_pins: pinmux_mcspi1_pins {
188 pinctrl-single,pins = <
189 OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
190 OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
191 OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
192 OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
193 >;
194 };
195
196 hsusb2_pins: pinmux_hsusb2_pins {
197 pinctrl-single,pins = <
198 OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
199 OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
200 OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
201 OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
202 OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
203 OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
204 >;
205 };
206
207 hsusb_otg_pins: pinmux_hsusb_otg_pins {
208 pinctrl-single,pins = <
209 OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
210 OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
211 OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
212 OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
213 OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */
214 OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
215 OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
216 OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */
217 OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */
218 OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */
219 OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
220 OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
221 >;
222 };
223
224 i2c1_pins: pinmux_i2c1_pins {
225 pinctrl-single,pins = <
226 OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */
227 OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */
228 OMAP3_CORE1_IOPAD(0x20ba, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs6.gpio_57 */
229 >;
230 };
231
232 i2c2_pins: pinmux_i2c2_pins {
233 pinctrl-single,pins = <
234 OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
235 OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
236 >;
237 };
238
239 i2c3_pins: pinmux_i2c3_pins {
240 pinctrl-single,pins = <
241 OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */
242 OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */
243 >;
244 };
245
246 tsc2004_pins: pinmux_tsc2004_pins {
247 pinctrl-single,pins = <
248 OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */
249 >;
250 };
251};
252
253&omap3_pmx_wkup {
254
255 hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
256 pinctrl-single,pins = <
257 OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
258 >;
259 };
260 wl127x_gpio: pinmux_wl127x_gpio_pin {
261 pinctrl-single,pins = <
262 OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4) /* sys_boot0.gpio_2 */
263 OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */
264 >;
265 };
266};
267
268&uart2 {
269 interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
270 pinctrl-names = "default";
271 pinctrl-0 = <&uart2_pins>;
272};
273
274&mcspi1 {
275 pinctrl-names = "default";
276 pinctrl-0 = <&mcspi1_pins>;
277};
278
279#include "twl4030.dtsi"
280#include "twl4030_omap3.dtsi"
281
282&vaux3 {
283 regulator-min-microvolt = <2800000>;
284 regulator-max-microvolt = <2800000>;
285};
286
287&twl {
288 twl_power: power {
289 compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
290 ti,use_poweroff;
291 };
292};
293
294&twl_gpio {
295 ti,use-leds;
296};
1/*
2 * This program is free software; you can redistribute it and/or modify
3 * it under the terms of the GNU General Public License version 2 as
4 * published by the Free Software Foundation.
5 */
6
7#include <dt-bindings/input/input.h>
8
9/ {
10 cpus {
11 cpu@0 {
12 cpu0-supply = <&vcc>;
13 };
14 };
15
16 wl12xx_vmmc: wl12xx_vmmc {
17 compatible = "regulator-fixed";
18 regulator-name = "vwl1271";
19 regulator-min-microvolt = <1800000>;
20 regulator-max-microvolt = <1800000>;
21 gpio = <&gpio1 3 0>; /* gpio_3 */
22 startup-delay-us = <70000>;
23 enable-active-high;
24 vin-supply = <&vmmc2>;
25 };
26
27 /* HS USB Host PHY on PORT 1 */
28 hsusb2_phy: hsusb2_phy {
29 compatible = "usb-nop-xceiv";
30 reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
31 };
32};
33
34&gpmc {
35 ranges = <0 0 0x00000000 0x1000000>; /* CS0: 16MB for NAND */
36
37 nand@0,0 {
38 linux,mtd-name = "micron,mt29f4g16abbda3w";
39 reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
40 nand-bus-width = <16>;
41 ti,nand-ecc-opt = "bch8";
42 gpmc,sync-clk-ps = <0>;
43 gpmc,cs-on-ns = <0>;
44 gpmc,cs-rd-off-ns = <44>;
45 gpmc,cs-wr-off-ns = <44>;
46 gpmc,adv-on-ns = <6>;
47 gpmc,adv-rd-off-ns = <34>;
48 gpmc,adv-wr-off-ns = <44>;
49 gpmc,we-off-ns = <40>;
50 gpmc,oe-off-ns = <54>;
51 gpmc,access-ns = <64>;
52 gpmc,rd-cycle-ns = <82>;
53 gpmc,wr-cycle-ns = <82>;
54 gpmc,wr-access-ns = <40>;
55 gpmc,wr-data-mux-bus-ns = <0>;
56 gpmc,device-width = <2>;
57
58 gpmc,page-burst-access-ns = <5>;
59 gpmc,cycle2cycle-delay-ns = <50>;
60
61 #address-cells = <1>;
62 #size-cells = <1>;
63
64 /* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */
65
66 x-loader@0 {
67 label = "x-loader";
68 reg = <0 0x80000>;
69 };
70
71 bootloaders@80000 {
72 label = "u-boot";
73 reg = <0x80000 0x1e0000>;
74 };
75
76 bootloaders_env@260000 {
77 label = "u-boot-env";
78 reg = <0x260000 0x20000>;
79 };
80
81 kernel@280000 {
82 label = "kernel";
83 reg = <0x280000 0x400000>;
84 };
85
86 filesystem@680000 {
87 label = "fs";
88 reg = <0x680000 0>; /* 0 = MTDPART_SIZ_FULL */
89 };
90 };
91};
92
93&i2c1 {
94 clock-frequency = <2600000>;
95
96 twl: twl@48 {
97 reg = <0x48>;
98 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
99 interrupt-parent = <&intc>;
100 twl_audio: audio {
101 compatible = "ti,twl4030-audio";
102 codec {
103 };
104 };
105 };
106};
107
108&i2c2 {
109 clock-frequency = <400000>;
110};
111
112&i2c3 {
113 clock-frequency = <400000>;
114};
115
116&mmc3 {
117 interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
118 pinctrl-0 = <&mmc3_pins>;
119 pinctrl-names = "default";
120 vmmc-supply = <&wl12xx_vmmc>;
121 non-removable;
122 bus-width = <4>;
123 cap-power-off-card;
124 #address-cells = <1>;
125 #size-cells = <0>;
126 wlcore: wlcore@2 {
127 compatible = "ti,wl1273";
128 reg = <2>;
129 interrupt-parent = <&gpio5>;
130 interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
131 ref-clock-frequency = <26000000>;
132 };
133};
134
135&usbhshost {
136 port2-mode = "ehci-phy";
137};
138
139&usbhsehci {
140 phys = <0 &hsusb2_phy>;
141};
142
143
144&omap3_pmx_core {
145 pinctrl-names = "default";
146 pinctrl-0 = <&hsusb2_pins>;
147
148 mmc3_pins: pinmux_mm3_pins {
149 pinctrl-single,pins = <
150 OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
151 OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
152 OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
153 OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
154 OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
155 OMAP3_CORE1_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */
156 OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
157 OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */
158 >;
159 };
160 mcbsp2_pins: pinmux_mcbsp2_pins {
161 pinctrl-single,pins = <
162 OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */
163 OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */
164 OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */
165 OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */
166 >;
167 };
168 uart2_pins: pinmux_uart2_pins {
169 pinctrl-single,pins = <
170 OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */
171 OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/
172 OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
173 OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
174 OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */
175 >;
176 };
177 mcspi1_pins: pinmux_mcspi1_pins {
178 pinctrl-single,pins = <
179 OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
180 OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
181 OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
182 OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
183 >;
184 };
185
186 hsusb2_pins: pinmux_hsusb2_pins {
187 pinctrl-single,pins = <
188 OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
189 OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
190 OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
191 OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
192 OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
193 OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
194 >;
195 };
196
197 hsusb_otg_pins: pinmux_hsusb_otg_pins {
198 pinctrl-single,pins = <
199 OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
200 OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
201 OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
202 OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
203 OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */
204 OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
205 OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
206 OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */
207 OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */
208 OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */
209 OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
210 OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
211 >;
212 };
213
214
215};
216
217&omap3_pmx_wkup {
218 pinctrl-names = "default";
219 pinctrl-0 = <&hsusb2_reset_pin>;
220 hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
221 pinctrl-single,pins = <
222 OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
223 >;
224 };
225};
226
227&omap3_pmx_core2 {
228 pinctrl-names = "default";
229 pinctrl-0 = <&hsusb2_2_pins>;
230 hsusb2_2_pins: pinmux_hsusb2_2_pins {
231 pinctrl-single,pins = <
232 OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
233 OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
234 OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
235 OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
236 OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
237 OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
238 >;
239 };
240};
241
242&uart2 {
243 interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
244 pinctrl-names = "default";
245 pinctrl-0 = <&uart2_pins>;
246};
247
248&mcspi1 {
249 pinctrl-names = "default";
250 pinctrl-0 = <&mcspi1_pins>;
251};
252
253#include "twl4030.dtsi"
254#include "twl4030_omap3.dtsi"
255
256&twl {
257 twl_power: power {
258 compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
259 ti,use_poweroff;
260 };
261};
262
263&twl_gpio {
264 ti,use-leds;
265};