1// SPDX-License-Identifier: GPL-2.0-or-later
 2/*
 3 * at91sam9g25ek.dts - Device Tree file for AT91SAM9G25-EK board
 4 *
 5 *  Copyright (C) 2012 Atmel,
 6 *                2012 Nicolas Ferre <nicolas.ferre@atmel.com>
 
 
 7 */
 8/dts-v1/;
 9#include "at91sam9g25.dtsi"
10#include "at91sam9x5ek.dtsi"
11
12/ {
13	model = "Atmel AT91SAM9G25-EK";
14	compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
15};
16
17&i2c0 {
18	camera@30 {
19		compatible = "ovti,ov2640";
20		reg = <0x30>;
21		pinctrl-names = "default";
22		pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
23		resetb-gpios = <&pioA 7 GPIO_ACTIVE_LOW>;
24		pwdn-gpios = <&pioA 13 GPIO_ACTIVE_HIGH>;
25		clocks = <&pmc PMC_TYPE_SYSTEM 8>;
26		clock-names = "xvclk";
27		assigned-clocks = <&pmc PMC_TYPE_SYSTEM 8>;
28		assigned-clock-rates = <25000000>;
29		status = "okay";
30
31		port {
32			ov2640_0: endpoint {
33				remote-endpoint = <&isi_0>;
34				bus-width = <8>;
35			};
36		};
37	};
38};
39
40&isi {
41	status = "okay";
 
42
43	port {
44		isi_0: endpoint@0 {
45			reg = <0>;
46			remote-endpoint = <&ov2640_0>;
47			bus-width = <8>;
48			vsync-active = <1>;
49			hsync-active = <1>;
50		};
51	};
52};
53
54&macb0 {
55	phy-mode = "rmii";
56	status = "okay";
57};
58
59&mmc1 {
60	status = "disabled";
61};
62
63&spi0 {
64	status = "disabled";
 
 
 
65};

 
 1/*
 2 * at91sam9g25ek.dts - Device Tree file for AT91SAM9G25-EK board
 3 *
 4 *  Copyright (C) 2012 Atmel,
 5 *                2012 Nicolas Ferre <nicolas.ferre@atmel.com>
 6 *
 7 * Licensed under GPLv2 or later.
 8 */
 9/dts-v1/;
10#include "at91sam9g25.dtsi"
11#include "at91sam9x5ek.dtsi"
12
13/ {
14	model = "Atmel AT91SAM9G25-EK";
15	compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
 
16
17	ahb {
18		apb {
19			spi0: spi@f0000000 {
20				status = "disabled";
 
 
 
 
 
 
 
 
 
 
 
 
 
 
21			};
 
 
 
22
23			mmc1: mmc@f000c000 {
24				status = "disabled";
25			};
26
27			i2c0: i2c@f8010000 {
28				ov2640: camera@0x30 {
29					status = "okay";
30				};
31			};
 
 
 
 
 
32
33			macb0: ethernet@f802c000 {
34				phy-mode = "rmii";
35				status = "okay";
36			};
 
 
 
 
37
38			isi: isi@f8048000 {
39				status = "okay";
40			};
41		};
42	};
43};