Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Native support for the Aiptek HyperPen USB Tablets
4 * (4000U/5000U/6000U/8000U/12000U)
5 *
6 * Copyright (c) 2001 Chris Atenasio <chris@crud.net>
7 * Copyright (c) 2002-2004 Bryan W. Headley <bwheadley@earthlink.net>
8 *
9 * based on wacom.c by
10 * Vojtech Pavlik <vojtech@suse.cz>
11 * Andreas Bach Aaen <abach@stofanet.dk>
12 * Clifford Wolf <clifford@clifford.at>
13 * Sam Mosel <sam.mosel@computer.org>
14 * James E. Blair <corvus@gnu.org>
15 * Daniel Egger <egger@suse.de>
16 *
17 * Many thanks to Oliver Kuechemann for his support.
18 *
19 * ChangeLog:
20 * v0.1 - Initial release
21 * v0.2 - Hack to get around fake event 28's. (Bryan W. Headley)
22 * v0.3 - Make URB dynamic (Bryan W. Headley, Jun-8-2002)
23 * Released to Linux 2.4.19 and 2.5.x
24 * v0.4 - Rewrote substantial portions of the code to deal with
25 * corrected control sequences, timing, dynamic configuration,
26 * support of 6000U - 12000U, procfs, and macro key support
27 * (Jan-1-2003 - Feb-5-2003, Bryan W. Headley)
28 * v1.0 - Added support for diagnostic messages, count of messages
29 * received from URB - Mar-8-2003, Bryan W. Headley
30 * v1.1 - added support for tablet resolution, changed DV and proximity
31 * some corrections - Jun-22-2003, martin schneebacher
32 * - Added support for the sysfs interface, deprecating the
33 * procfs interface for 2.5.x kernel. Also added support for
34 * Wheel command. Bryan W. Headley July-15-2003.
35 * v1.2 - Reworked jitter timer as a kernel thread.
36 * Bryan W. Headley November-28-2003/Jan-10-2004.
37 * v1.3 - Repaired issue of kernel thread going nuts on single-processor
38 * machines, introduced programmableDelay as a command line
39 * parameter. Feb 7 2004, Bryan W. Headley.
40 * v1.4 - Re-wire jitter so it does not require a thread. Courtesy of
41 * Rene van Paassen. Added reporting of physical pointer device
42 * (e.g., stylus, mouse in reports 2, 3, 4, 5. We don't know
43 * for reports 1, 6.)
44 * what physical device reports for reports 1, 6.) Also enabled
45 * MOUSE and LENS tool button modes. Renamed "rubber" to "eraser".
46 * Feb 20, 2004, Bryan W. Headley.
47 * v1.5 - Added previousJitterable, so we don't do jitter delay when the
48 * user is holding a button down for periods of time.
49 *
50 * NOTE:
51 * This kernel driver is augmented by the "Aiptek" XFree86 input
52 * driver for your X server, as well as the Gaiptek GUI Front-end
53 * "Tablet Manager".
54 * These three products are highly interactive with one another,
55 * so therefore it's easier to document them all as one subsystem.
56 * Please visit the project's "home page", located at,
57 * http://aiptektablet.sourceforge.net.
58 */
59
60#include <linux/jiffies.h>
61#include <linux/kernel.h>
62#include <linux/slab.h>
63#include <linux/module.h>
64#include <linux/usb/input.h>
65#include <linux/uaccess.h>
66#include <asm/unaligned.h>
67
68/*
69 * Aiptek status packet:
70 *
71 * (returned as Report 1 - relative coordinates from mouse and stylus)
72 *
73 * bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
74 * byte0 0 0 0 0 0 0 0 1
75 * byte1 0 0 0 0 0 BS2 BS Tip
76 * byte2 X7 X6 X5 X4 X3 X2 X1 X0
77 * byte3 Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
78 *
79 * (returned as Report 2 - absolute coordinates from the stylus)
80 *
81 * bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
82 * byte0 0 0 0 0 0 0 1 0
83 * byte1 X7 X6 X5 X4 X3 X2 X1 X0
84 * byte2 X15 X14 X13 X12 X11 X10 X9 X8
85 * byte3 Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
86 * byte4 Y15 Y14 Y13 Y12 Y11 Y10 Y9 Y8
87 * byte5 * * * BS2 BS1 Tip IR DV
88 * byte6 P7 P6 P5 P4 P3 P2 P1 P0
89 * byte7 P15 P14 P13 P12 P11 P10 P9 P8
90 *
91 * (returned as Report 3 - absolute coordinates from the mouse)
92 *
93 * bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
94 * byte0 0 0 0 0 0 0 1 1
95 * byte1 X7 X6 X5 X4 X3 X2 X1 X0
96 * byte2 X15 X14 X13 X12 X11 X10 X9 X8
97 * byte3 Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
98 * byte4 Y15 Y14 Y13 Y12 Y11 Y10 Y9 Y8
99 * byte5 * * * BS2 BS1 Tip IR DV
100 * byte6 P7 P6 P5 P4 P3 P2 P1 P0
101 * byte7 P15 P14 P13 P12 P11 P10 P9 P8
102 *
103 * (returned as Report 4 - macrokeys from the stylus)
104 *
105 * bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
106 * byte0 0 0 0 0 0 1 0 0
107 * byte1 0 0 0 BS2 BS Tip IR DV
108 * byte2 0 0 0 0 0 0 1 0
109 * byte3 0 0 0 K4 K3 K2 K1 K0
110 * byte4 P7 P6 P5 P4 P3 P2 P1 P0
111 * byte5 P15 P14 P13 P12 P11 P10 P9 P8
112 *
113 * (returned as Report 5 - macrokeys from the mouse)
114 *
115 * bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
116 * byte0 0 0 0 0 0 1 0 1
117 * byte1 0 0 0 BS2 BS Tip IR DV
118 * byte2 0 0 0 0 0 0 1 0
119 * byte3 0 0 0 K4 K3 K2 K1 K0
120 * byte4 P7 P6 P5 P4 P3 P2 P1 P0
121 * byte5 P15 P14 P13 P12 P11 P10 P9 P8
122 *
123 * IR: In Range = Proximity on
124 * DV = Data Valid
125 * BS = Barrel Switch (as in, macro keys)
126 * BS2 also referred to as Tablet Pick
127 *
128 * Command Summary:
129 *
130 * Use report_type CONTROL (3)
131 * Use report_id 2
132 *
133 * Command/Data Description Return Bytes Return Value
134 * 0x10/0x00 SwitchToMouse 0
135 * 0x10/0x01 SwitchToTablet 0
136 * 0x18/0x04 SetResolution 0
137 * 0x12/0xFF AutoGainOn 0
138 * 0x17/0x00 FilterOn 0
139 * 0x01/0x00 GetXExtension 2 MaxX
140 * 0x01/0x01 GetYExtension 2 MaxY
141 * 0x02/0x00 GetModelCode 2 ModelCode = LOBYTE
142 * 0x03/0x00 GetODMCode 2 ODMCode
143 * 0x08/0x00 GetPressureLevels 2 =512
144 * 0x04/0x00 GetFirmwareVersion 2 Firmware Version
145 * 0x11/0x02 EnableMacroKeys 0
146 *
147 * To initialize the tablet:
148 *
149 * (1) Send Resolution500LPI (Command)
150 * (2) Query for Model code (Option Report)
151 * (3) Query for ODM code (Option Report)
152 * (4) Query for firmware (Option Report)
153 * (5) Query for GetXExtension (Option Report)
154 * (6) Query for GetYExtension (Option Report)
155 * (7) Query for GetPressureLevels (Option Report)
156 * (8) SwitchToTablet for Absolute coordinates, or
157 * SwitchToMouse for Relative coordinates (Command)
158 * (9) EnableMacroKeys (Command)
159 * (10) FilterOn (Command)
160 * (11) AutoGainOn (Command)
161 *
162 * (Step 9 can be omitted, but you'll then have no function keys.)
163 */
164
165#define USB_VENDOR_ID_AIPTEK 0x08ca
166#define USB_VENDOR_ID_KYE 0x0458
167#define USB_REQ_GET_REPORT 0x01
168#define USB_REQ_SET_REPORT 0x09
169
170 /* PointerMode codes
171 */
172#define AIPTEK_POINTER_ONLY_MOUSE_MODE 0
173#define AIPTEK_POINTER_ONLY_STYLUS_MODE 1
174#define AIPTEK_POINTER_EITHER_MODE 2
175
176#define AIPTEK_POINTER_ALLOW_MOUSE_MODE(a) \
177 (a == AIPTEK_POINTER_ONLY_MOUSE_MODE || \
178 a == AIPTEK_POINTER_EITHER_MODE)
179#define AIPTEK_POINTER_ALLOW_STYLUS_MODE(a) \
180 (a == AIPTEK_POINTER_ONLY_STYLUS_MODE || \
181 a == AIPTEK_POINTER_EITHER_MODE)
182
183 /* CoordinateMode code
184 */
185#define AIPTEK_COORDINATE_RELATIVE_MODE 0
186#define AIPTEK_COORDINATE_ABSOLUTE_MODE 1
187
188 /* XTilt and YTilt values
189 */
190#define AIPTEK_TILT_MIN (-128)
191#define AIPTEK_TILT_MAX 127
192#define AIPTEK_TILT_DISABLE (-10101)
193
194 /* Wheel values
195 */
196#define AIPTEK_WHEEL_MIN 0
197#define AIPTEK_WHEEL_MAX 1024
198#define AIPTEK_WHEEL_DISABLE (-10101)
199
200 /* ToolCode values, which BTW are 0x140 .. 0x14f
201 * We have things set up such that if the tool button has changed,
202 * the tools get reset.
203 */
204 /* toolMode codes
205 */
206#define AIPTEK_TOOL_BUTTON_PEN_MODE BTN_TOOL_PEN
207#define AIPTEK_TOOL_BUTTON_PENCIL_MODE BTN_TOOL_PENCIL
208#define AIPTEK_TOOL_BUTTON_BRUSH_MODE BTN_TOOL_BRUSH
209#define AIPTEK_TOOL_BUTTON_AIRBRUSH_MODE BTN_TOOL_AIRBRUSH
210#define AIPTEK_TOOL_BUTTON_ERASER_MODE BTN_TOOL_RUBBER
211#define AIPTEK_TOOL_BUTTON_MOUSE_MODE BTN_TOOL_MOUSE
212#define AIPTEK_TOOL_BUTTON_LENS_MODE BTN_TOOL_LENS
213
214 /* Diagnostic message codes
215 */
216#define AIPTEK_DIAGNOSTIC_NA 0
217#define AIPTEK_DIAGNOSTIC_SENDING_RELATIVE_IN_ABSOLUTE 1
218#define AIPTEK_DIAGNOSTIC_SENDING_ABSOLUTE_IN_RELATIVE 2
219#define AIPTEK_DIAGNOSTIC_TOOL_DISALLOWED 3
220
221 /* Time to wait (in ms) to help mask hand jittering
222 * when pressing the stylus buttons.
223 */
224#define AIPTEK_JITTER_DELAY_DEFAULT 50
225
226 /* Time to wait (in ms) in-between sending the tablet
227 * a command and beginning the process of reading the return
228 * sequence from the tablet.
229 */
230#define AIPTEK_PROGRAMMABLE_DELAY_25 25
231#define AIPTEK_PROGRAMMABLE_DELAY_50 50
232#define AIPTEK_PROGRAMMABLE_DELAY_100 100
233#define AIPTEK_PROGRAMMABLE_DELAY_200 200
234#define AIPTEK_PROGRAMMABLE_DELAY_300 300
235#define AIPTEK_PROGRAMMABLE_DELAY_400 400
236#define AIPTEK_PROGRAMMABLE_DELAY_DEFAULT AIPTEK_PROGRAMMABLE_DELAY_400
237
238 /* Mouse button programming
239 */
240#define AIPTEK_MOUSE_LEFT_BUTTON 0x04
241#define AIPTEK_MOUSE_RIGHT_BUTTON 0x08
242#define AIPTEK_MOUSE_MIDDLE_BUTTON 0x10
243
244 /* Stylus button programming
245 */
246#define AIPTEK_STYLUS_LOWER_BUTTON 0x08
247#define AIPTEK_STYLUS_UPPER_BUTTON 0x10
248
249 /* Length of incoming packet from the tablet
250 */
251#define AIPTEK_PACKET_LENGTH 8
252
253 /* We report in EV_MISC both the proximity and
254 * whether the report came from the stylus, tablet mouse
255 * or "unknown" -- Unknown when the tablet is in relative
256 * mode, because we only get report 1's.
257 */
258#define AIPTEK_REPORT_TOOL_UNKNOWN 0x10
259#define AIPTEK_REPORT_TOOL_STYLUS 0x20
260#define AIPTEK_REPORT_TOOL_MOUSE 0x40
261
262static int programmableDelay = AIPTEK_PROGRAMMABLE_DELAY_DEFAULT;
263static int jitterDelay = AIPTEK_JITTER_DELAY_DEFAULT;
264
265struct aiptek_features {
266 int odmCode; /* Tablet manufacturer code */
267 int modelCode; /* Tablet model code (not unique) */
268 int firmwareCode; /* prom/eeprom version */
269 char usbPath[64 + 1]; /* device's physical usb path */
270};
271
272struct aiptek_settings {
273 int pointerMode; /* stylus-, mouse-only or either */
274 int coordinateMode; /* absolute/relative coords */
275 int toolMode; /* pen, pencil, brush, etc. tool */
276 int xTilt; /* synthetic xTilt amount */
277 int yTilt; /* synthetic yTilt amount */
278 int wheel; /* synthetic wheel amount */
279 int stylusButtonUpper; /* stylus upper btn delivers... */
280 int stylusButtonLower; /* stylus lower btn delivers... */
281 int mouseButtonLeft; /* mouse left btn delivers... */
282 int mouseButtonMiddle; /* mouse middle btn delivers... */
283 int mouseButtonRight; /* mouse right btn delivers... */
284 int programmableDelay; /* delay for tablet programming */
285 int jitterDelay; /* delay for hand jittering */
286};
287
288struct aiptek {
289 struct input_dev *inputdev; /* input device struct */
290 struct usb_interface *intf; /* usb interface struct */
291 struct urb *urb; /* urb for incoming reports */
292 dma_addr_t data_dma; /* our dma stuffage */
293 struct aiptek_features features; /* tablet's array of features */
294 struct aiptek_settings curSetting; /* tablet's current programmable */
295 struct aiptek_settings newSetting; /* ... and new param settings */
296 unsigned int ifnum; /* interface number for IO */
297 int diagnostic; /* tablet diagnostic codes */
298 unsigned long eventCount; /* event count */
299 int inDelay; /* jitter: in jitter delay? */
300 unsigned long endDelay; /* jitter: time when delay ends */
301 int previousJitterable; /* jitterable prev value */
302
303 int lastMacro; /* macro key to reset */
304 int previousToolMode; /* pen, pencil, brush, etc. tool */
305 unsigned char *data; /* incoming packet data */
306};
307
308static const int eventTypes[] = {
309 EV_KEY, EV_ABS, EV_REL, EV_MSC,
310};
311
312static const int absEvents[] = {
313 ABS_X, ABS_Y, ABS_PRESSURE, ABS_TILT_X, ABS_TILT_Y,
314 ABS_WHEEL, ABS_MISC,
315};
316
317static const int relEvents[] = {
318 REL_X, REL_Y, REL_WHEEL,
319};
320
321static const int buttonEvents[] = {
322 BTN_LEFT, BTN_RIGHT, BTN_MIDDLE,
323 BTN_TOOL_PEN, BTN_TOOL_RUBBER, BTN_TOOL_PENCIL, BTN_TOOL_AIRBRUSH,
324 BTN_TOOL_BRUSH, BTN_TOOL_MOUSE, BTN_TOOL_LENS, BTN_TOUCH,
325 BTN_STYLUS, BTN_STYLUS2,
326};
327
328/*
329 * Permit easy lookup of keyboard events to send, versus
330 * the bitmap which comes from the tablet. This hides the
331 * issue that the F_keys are not sequentially numbered.
332 */
333static const int macroKeyEvents[] = {
334 KEY_ESC, KEY_F1, KEY_F2, KEY_F3, KEY_F4, KEY_F5,
335 KEY_F6, KEY_F7, KEY_F8, KEY_F9, KEY_F10, KEY_F11,
336 KEY_F12, KEY_F13, KEY_F14, KEY_F15, KEY_F16, KEY_F17,
337 KEY_F18, KEY_F19, KEY_F20, KEY_F21, KEY_F22, KEY_F23,
338 KEY_F24, KEY_STOP, KEY_AGAIN, KEY_PROPS, KEY_UNDO,
339 KEY_FRONT, KEY_COPY, KEY_OPEN, KEY_PASTE, 0
340};
341
342/***********************************************************************
343 * Map values to strings and back. Every map should have the following
344 * as its last element: { NULL, AIPTEK_INVALID_VALUE }.
345 */
346#define AIPTEK_INVALID_VALUE -1
347
348struct aiptek_map {
349 const char *string;
350 int value;
351};
352
353static int map_str_to_val(const struct aiptek_map *map, const char *str, size_t count)
354{
355 const struct aiptek_map *p;
356
357 if (str[count - 1] == '\n')
358 count--;
359
360 for (p = map; p->string; p++)
361 if (!strncmp(str, p->string, count))
362 return p->value;
363
364 return AIPTEK_INVALID_VALUE;
365}
366
367static const char *map_val_to_str(const struct aiptek_map *map, int val)
368{
369 const struct aiptek_map *p;
370
371 for (p = map; p->value != AIPTEK_INVALID_VALUE; p++)
372 if (val == p->value)
373 return p->string;
374
375 return "unknown";
376}
377
378/***********************************************************************
379 * aiptek_irq can receive one of six potential reports.
380 * The documentation for each is in the body of the function.
381 *
382 * The tablet reports on several attributes per invocation of
383 * aiptek_irq. Because the Linux Input Event system allows the
384 * transmission of ONE attribute per input_report_xxx() call,
385 * collation has to be done on the other end to reconstitute
386 * a complete tablet report. Further, the number of Input Event reports
387 * submitted varies, depending on what USB report type, and circumstance.
388 * To deal with this, EV_MSC is used to indicate an 'end-of-report'
389 * message. This has been an undocumented convention understood by the kernel
390 * tablet driver and clients such as gpm and XFree86's tablet drivers.
391 *
392 * Of the information received from the tablet, the one piece I
393 * cannot transmit is the proximity bit (without resorting to an EV_MSC
394 * convention above.) I therefore have taken over REL_MISC and ABS_MISC
395 * (for relative and absolute reports, respectively) for communicating
396 * Proximity. Why two events? I thought it interesting to know if the
397 * Proximity event occurred while the tablet was in absolute or relative
398 * mode.
399 * Update: REL_MISC proved not to be such a good idea. With REL_MISC you
400 * get an event transmitted each time. ABS_MISC works better, since it
401 * can be set and re-set. Thus, only using ABS_MISC from now on.
402 *
403 * Other tablets use the notion of a certain minimum stylus pressure
404 * to infer proximity. While that could have been done, that is yet
405 * another 'by convention' behavior, the documentation for which
406 * would be spread between two (or more) pieces of software.
407 *
408 * EV_MSC usage was terminated for this purpose in Linux 2.5.x, and
409 * replaced with the input_sync() method (which emits EV_SYN.)
410 */
411
412static void aiptek_irq(struct urb *urb)
413{
414 struct aiptek *aiptek = urb->context;
415 unsigned char *data = aiptek->data;
416 struct input_dev *inputdev = aiptek->inputdev;
417 struct usb_interface *intf = aiptek->intf;
418 int jitterable = 0;
419 int retval, macro, x, y, z, left, right, middle, p, dv, tip, bs, pck;
420
421 switch (urb->status) {
422 case 0:
423 /* Success */
424 break;
425
426 case -ECONNRESET:
427 case -ENOENT:
428 case -ESHUTDOWN:
429 /* This urb is terminated, clean up */
430 dev_dbg(&intf->dev, "%s - urb shutting down with status: %d\n",
431 __func__, urb->status);
432 return;
433
434 default:
435 dev_dbg(&intf->dev, "%s - nonzero urb status received: %d\n",
436 __func__, urb->status);
437 goto exit;
438 }
439
440 /* See if we are in a delay loop -- throw out report if true.
441 */
442 if (aiptek->inDelay == 1 && time_after(aiptek->endDelay, jiffies)) {
443 goto exit;
444 }
445
446 aiptek->inDelay = 0;
447 aiptek->eventCount++;
448
449 /* Report 1 delivers relative coordinates with either a stylus
450 * or the mouse. You do not know, however, which input
451 * tool generated the event.
452 */
453 if (data[0] == 1) {
454 if (aiptek->curSetting.coordinateMode ==
455 AIPTEK_COORDINATE_ABSOLUTE_MODE) {
456 aiptek->diagnostic =
457 AIPTEK_DIAGNOSTIC_SENDING_RELATIVE_IN_ABSOLUTE;
458 } else {
459 x = (signed char) data[2];
460 y = (signed char) data[3];
461
462 /* jitterable keeps track of whether any button has been pressed.
463 * We're also using it to remap the physical mouse button mask
464 * to pseudo-settings. (We don't specifically care about it's
465 * value after moving/transposing mouse button bitmasks, except
466 * that a non-zero value indicates that one or more
467 * mouse button was pressed.)
468 */
469 jitterable = data[1] & 0x07;
470
471 left = (data[1] & aiptek->curSetting.mouseButtonLeft >> 2) != 0 ? 1 : 0;
472 right = (data[1] & aiptek->curSetting.mouseButtonRight >> 2) != 0 ? 1 : 0;
473 middle = (data[1] & aiptek->curSetting.mouseButtonMiddle >> 2) != 0 ? 1 : 0;
474
475 input_report_key(inputdev, BTN_LEFT, left);
476 input_report_key(inputdev, BTN_MIDDLE, middle);
477 input_report_key(inputdev, BTN_RIGHT, right);
478
479 input_report_abs(inputdev, ABS_MISC,
480 1 | AIPTEK_REPORT_TOOL_UNKNOWN);
481 input_report_rel(inputdev, REL_X, x);
482 input_report_rel(inputdev, REL_Y, y);
483
484 /* Wheel support is in the form of a single-event
485 * firing.
486 */
487 if (aiptek->curSetting.wheel != AIPTEK_WHEEL_DISABLE) {
488 input_report_rel(inputdev, REL_WHEEL,
489 aiptek->curSetting.wheel);
490 aiptek->curSetting.wheel = AIPTEK_WHEEL_DISABLE;
491 }
492 if (aiptek->lastMacro != -1) {
493 input_report_key(inputdev,
494 macroKeyEvents[aiptek->lastMacro], 0);
495 aiptek->lastMacro = -1;
496 }
497 input_sync(inputdev);
498 }
499 }
500 /* Report 2 is delivered only by the stylus, and delivers
501 * absolute coordinates.
502 */
503 else if (data[0] == 2) {
504 if (aiptek->curSetting.coordinateMode == AIPTEK_COORDINATE_RELATIVE_MODE) {
505 aiptek->diagnostic = AIPTEK_DIAGNOSTIC_SENDING_ABSOLUTE_IN_RELATIVE;
506 } else if (!AIPTEK_POINTER_ALLOW_STYLUS_MODE
507 (aiptek->curSetting.pointerMode)) {
508 aiptek->diagnostic = AIPTEK_DIAGNOSTIC_TOOL_DISALLOWED;
509 } else {
510 x = get_unaligned_le16(data + 1);
511 y = get_unaligned_le16(data + 3);
512 z = get_unaligned_le16(data + 6);
513
514 dv = (data[5] & 0x01) != 0 ? 1 : 0;
515 p = (data[5] & 0x02) != 0 ? 1 : 0;
516 tip = (data[5] & 0x04) != 0 ? 1 : 0;
517
518 /* Use jitterable to re-arrange button masks
519 */
520 jitterable = data[5] & 0x18;
521
522 bs = (data[5] & aiptek->curSetting.stylusButtonLower) != 0 ? 1 : 0;
523 pck = (data[5] & aiptek->curSetting.stylusButtonUpper) != 0 ? 1 : 0;
524
525 /* dv indicates 'data valid' (e.g., the tablet is in sync
526 * and has delivered a "correct" report) We will ignore
527 * all 'bad' reports...
528 */
529 if (dv != 0) {
530 /* If the selected tool changed, reset the old
531 * tool key, and set the new one.
532 */
533 if (aiptek->previousToolMode !=
534 aiptek->curSetting.toolMode) {
535 input_report_key(inputdev,
536 aiptek->previousToolMode, 0);
537 input_report_key(inputdev,
538 aiptek->curSetting.toolMode,
539 1);
540 aiptek->previousToolMode =
541 aiptek->curSetting.toolMode;
542 }
543
544 if (p != 0) {
545 input_report_abs(inputdev, ABS_X, x);
546 input_report_abs(inputdev, ABS_Y, y);
547 input_report_abs(inputdev, ABS_PRESSURE, z);
548
549 input_report_key(inputdev, BTN_TOUCH, tip);
550 input_report_key(inputdev, BTN_STYLUS, bs);
551 input_report_key(inputdev, BTN_STYLUS2, pck);
552
553 if (aiptek->curSetting.xTilt !=
554 AIPTEK_TILT_DISABLE) {
555 input_report_abs(inputdev,
556 ABS_TILT_X,
557 aiptek->curSetting.xTilt);
558 }
559 if (aiptek->curSetting.yTilt != AIPTEK_TILT_DISABLE) {
560 input_report_abs(inputdev,
561 ABS_TILT_Y,
562 aiptek->curSetting.yTilt);
563 }
564
565 /* Wheel support is in the form of a single-event
566 * firing.
567 */
568 if (aiptek->curSetting.wheel !=
569 AIPTEK_WHEEL_DISABLE) {
570 input_report_abs(inputdev,
571 ABS_WHEEL,
572 aiptek->curSetting.wheel);
573 aiptek->curSetting.wheel = AIPTEK_WHEEL_DISABLE;
574 }
575 }
576 input_report_abs(inputdev, ABS_MISC, p | AIPTEK_REPORT_TOOL_STYLUS);
577 if (aiptek->lastMacro != -1) {
578 input_report_key(inputdev,
579 macroKeyEvents[aiptek->lastMacro], 0);
580 aiptek->lastMacro = -1;
581 }
582 input_sync(inputdev);
583 }
584 }
585 }
586 /* Report 3's come from the mouse in absolute mode.
587 */
588 else if (data[0] == 3) {
589 if (aiptek->curSetting.coordinateMode == AIPTEK_COORDINATE_RELATIVE_MODE) {
590 aiptek->diagnostic = AIPTEK_DIAGNOSTIC_SENDING_ABSOLUTE_IN_RELATIVE;
591 } else if (!AIPTEK_POINTER_ALLOW_MOUSE_MODE
592 (aiptek->curSetting.pointerMode)) {
593 aiptek->diagnostic = AIPTEK_DIAGNOSTIC_TOOL_DISALLOWED;
594 } else {
595 x = get_unaligned_le16(data + 1);
596 y = get_unaligned_le16(data + 3);
597
598 jitterable = data[5] & 0x1c;
599
600 dv = (data[5] & 0x01) != 0 ? 1 : 0;
601 p = (data[5] & 0x02) != 0 ? 1 : 0;
602 left = (data[5] & aiptek->curSetting.mouseButtonLeft) != 0 ? 1 : 0;
603 right = (data[5] & aiptek->curSetting.mouseButtonRight) != 0 ? 1 : 0;
604 middle = (data[5] & aiptek->curSetting.mouseButtonMiddle) != 0 ? 1 : 0;
605
606 if (dv != 0) {
607 /* If the selected tool changed, reset the old
608 * tool key, and set the new one.
609 */
610 if (aiptek->previousToolMode !=
611 aiptek->curSetting.toolMode) {
612 input_report_key(inputdev,
613 aiptek->previousToolMode, 0);
614 input_report_key(inputdev,
615 aiptek->curSetting.toolMode,
616 1);
617 aiptek->previousToolMode =
618 aiptek->curSetting.toolMode;
619 }
620
621 if (p != 0) {
622 input_report_abs(inputdev, ABS_X, x);
623 input_report_abs(inputdev, ABS_Y, y);
624
625 input_report_key(inputdev, BTN_LEFT, left);
626 input_report_key(inputdev, BTN_MIDDLE, middle);
627 input_report_key(inputdev, BTN_RIGHT, right);
628
629 /* Wheel support is in the form of a single-event
630 * firing.
631 */
632 if (aiptek->curSetting.wheel != AIPTEK_WHEEL_DISABLE) {
633 input_report_abs(inputdev,
634 ABS_WHEEL,
635 aiptek->curSetting.wheel);
636 aiptek->curSetting.wheel = AIPTEK_WHEEL_DISABLE;
637 }
638 }
639 input_report_abs(inputdev, ABS_MISC, p | AIPTEK_REPORT_TOOL_MOUSE);
640 if (aiptek->lastMacro != -1) {
641 input_report_key(inputdev,
642 macroKeyEvents[aiptek->lastMacro], 0);
643 aiptek->lastMacro = -1;
644 }
645 input_sync(inputdev);
646 }
647 }
648 }
649 /* Report 4s come from the macro keys when pressed by stylus
650 */
651 else if (data[0] == 4) {
652 jitterable = data[1] & 0x18;
653
654 dv = (data[1] & 0x01) != 0 ? 1 : 0;
655 p = (data[1] & 0x02) != 0 ? 1 : 0;
656 tip = (data[1] & 0x04) != 0 ? 1 : 0;
657 bs = (data[1] & aiptek->curSetting.stylusButtonLower) != 0 ? 1 : 0;
658 pck = (data[1] & aiptek->curSetting.stylusButtonUpper) != 0 ? 1 : 0;
659
660 macro = dv && p && tip && !(data[3] & 1) ? (data[3] >> 1) : -1;
661 z = get_unaligned_le16(data + 4);
662
663 if (dv) {
664 /* If the selected tool changed, reset the old
665 * tool key, and set the new one.
666 */
667 if (aiptek->previousToolMode !=
668 aiptek->curSetting.toolMode) {
669 input_report_key(inputdev,
670 aiptek->previousToolMode, 0);
671 input_report_key(inputdev,
672 aiptek->curSetting.toolMode,
673 1);
674 aiptek->previousToolMode =
675 aiptek->curSetting.toolMode;
676 }
677 }
678
679 if (aiptek->lastMacro != -1 && aiptek->lastMacro != macro) {
680 input_report_key(inputdev, macroKeyEvents[aiptek->lastMacro], 0);
681 aiptek->lastMacro = -1;
682 }
683
684 if (macro != -1 && macro != aiptek->lastMacro) {
685 input_report_key(inputdev, macroKeyEvents[macro], 1);
686 aiptek->lastMacro = macro;
687 }
688 input_report_abs(inputdev, ABS_MISC,
689 p | AIPTEK_REPORT_TOOL_STYLUS);
690 input_sync(inputdev);
691 }
692 /* Report 5s come from the macro keys when pressed by mouse
693 */
694 else if (data[0] == 5) {
695 jitterable = data[1] & 0x1c;
696
697 dv = (data[1] & 0x01) != 0 ? 1 : 0;
698 p = (data[1] & 0x02) != 0 ? 1 : 0;
699 left = (data[1]& aiptek->curSetting.mouseButtonLeft) != 0 ? 1 : 0;
700 right = (data[1] & aiptek->curSetting.mouseButtonRight) != 0 ? 1 : 0;
701 middle = (data[1] & aiptek->curSetting.mouseButtonMiddle) != 0 ? 1 : 0;
702 macro = dv && p && left && !(data[3] & 1) ? (data[3] >> 1) : 0;
703
704 if (dv) {
705 /* If the selected tool changed, reset the old
706 * tool key, and set the new one.
707 */
708 if (aiptek->previousToolMode !=
709 aiptek->curSetting.toolMode) {
710 input_report_key(inputdev,
711 aiptek->previousToolMode, 0);
712 input_report_key(inputdev,
713 aiptek->curSetting.toolMode, 1);
714 aiptek->previousToolMode = aiptek->curSetting.toolMode;
715 }
716 }
717
718 if (aiptek->lastMacro != -1 && aiptek->lastMacro != macro) {
719 input_report_key(inputdev, macroKeyEvents[aiptek->lastMacro], 0);
720 aiptek->lastMacro = -1;
721 }
722
723 if (macro != -1 && macro != aiptek->lastMacro) {
724 input_report_key(inputdev, macroKeyEvents[macro], 1);
725 aiptek->lastMacro = macro;
726 }
727
728 input_report_abs(inputdev, ABS_MISC,
729 p | AIPTEK_REPORT_TOOL_MOUSE);
730 input_sync(inputdev);
731 }
732 /* We have no idea which tool can generate a report 6. Theoretically,
733 * neither need to, having been given reports 4 & 5 for such use.
734 * However, report 6 is the 'official-looking' report for macroKeys;
735 * reports 4 & 5 supposively are used to support unnamed, unknown
736 * hat switches (which just so happen to be the macroKeys.)
737 */
738 else if (data[0] == 6) {
739 macro = get_unaligned_le16(data + 1);
740 if (macro > 0) {
741 input_report_key(inputdev, macroKeyEvents[macro - 1],
742 0);
743 }
744 if (macro < 25) {
745 input_report_key(inputdev, macroKeyEvents[macro + 1],
746 0);
747 }
748
749 /* If the selected tool changed, reset the old
750 tool key, and set the new one.
751 */
752 if (aiptek->previousToolMode !=
753 aiptek->curSetting.toolMode) {
754 input_report_key(inputdev,
755 aiptek->previousToolMode, 0);
756 input_report_key(inputdev,
757 aiptek->curSetting.toolMode,
758 1);
759 aiptek->previousToolMode =
760 aiptek->curSetting.toolMode;
761 }
762
763 input_report_key(inputdev, macroKeyEvents[macro], 1);
764 input_report_abs(inputdev, ABS_MISC,
765 1 | AIPTEK_REPORT_TOOL_UNKNOWN);
766 input_sync(inputdev);
767 } else {
768 dev_dbg(&intf->dev, "Unknown report %d\n", data[0]);
769 }
770
771 /* Jitter may occur when the user presses a button on the stlyus
772 * or the mouse. What we do to prevent that is wait 'x' milliseconds
773 * following a 'jitterable' event, which should give the hand some time
774 * stabilize itself.
775 *
776 * We just introduced aiptek->previousJitterable to carry forth the
777 * notion that jitter occurs when the button state changes from on to off:
778 * a person drawing, holding a button down is not subject to jittering.
779 * With that in mind, changing from upper button depressed to lower button
780 * WILL transition through a jitter delay.
781 */
782
783 if (aiptek->previousJitterable != jitterable &&
784 aiptek->curSetting.jitterDelay != 0 && aiptek->inDelay != 1) {
785 aiptek->endDelay = jiffies +
786 ((aiptek->curSetting.jitterDelay * HZ) / 1000);
787 aiptek->inDelay = 1;
788 }
789 aiptek->previousJitterable = jitterable;
790
791exit:
792 retval = usb_submit_urb(urb, GFP_ATOMIC);
793 if (retval != 0) {
794 dev_err(&intf->dev,
795 "%s - usb_submit_urb failed with result %d\n",
796 __func__, retval);
797 }
798}
799
800/***********************************************************************
801 * These are the USB id's known so far. We do not identify them to
802 * specific Aiptek model numbers, because there has been overlaps,
803 * use, and reuse of id's in existing models. Certain models have
804 * been known to use more than one ID, indicative perhaps of
805 * manufacturing revisions. In any event, we consider these
806 * IDs to not be model-specific nor unique.
807 */
808static const struct usb_device_id aiptek_ids[] = {
809 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x01)},
810 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x10)},
811 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x20)},
812 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x21)},
813 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x22)},
814 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x23)},
815 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x24)},
816 {USB_DEVICE(USB_VENDOR_ID_KYE, 0x5003)},
817 {}
818};
819
820MODULE_DEVICE_TABLE(usb, aiptek_ids);
821
822/***********************************************************************
823 * Open an instance of the tablet driver.
824 */
825static int aiptek_open(struct input_dev *inputdev)
826{
827 struct aiptek *aiptek = input_get_drvdata(inputdev);
828
829 aiptek->urb->dev = interface_to_usbdev(aiptek->intf);
830 if (usb_submit_urb(aiptek->urb, GFP_KERNEL) != 0)
831 return -EIO;
832
833 return 0;
834}
835
836/***********************************************************************
837 * Close an instance of the tablet driver.
838 */
839static void aiptek_close(struct input_dev *inputdev)
840{
841 struct aiptek *aiptek = input_get_drvdata(inputdev);
842
843 usb_kill_urb(aiptek->urb);
844}
845
846/***********************************************************************
847 * aiptek_set_report and aiptek_get_report() are borrowed from Linux 2.4.x,
848 * where they were known as usb_set_report and usb_get_report.
849 */
850static int
851aiptek_set_report(struct aiptek *aiptek,
852 unsigned char report_type,
853 unsigned char report_id, void *buffer, int size)
854{
855 struct usb_device *udev = interface_to_usbdev(aiptek->intf);
856
857 return usb_control_msg(udev,
858 usb_sndctrlpipe(udev, 0),
859 USB_REQ_SET_REPORT,
860 USB_TYPE_CLASS | USB_RECIP_INTERFACE |
861 USB_DIR_OUT, (report_type << 8) + report_id,
862 aiptek->ifnum, buffer, size, 5000);
863}
864
865static int
866aiptek_get_report(struct aiptek *aiptek,
867 unsigned char report_type,
868 unsigned char report_id, void *buffer, int size)
869{
870 struct usb_device *udev = interface_to_usbdev(aiptek->intf);
871
872 return usb_control_msg(udev,
873 usb_rcvctrlpipe(udev, 0),
874 USB_REQ_GET_REPORT,
875 USB_TYPE_CLASS | USB_RECIP_INTERFACE |
876 USB_DIR_IN, (report_type << 8) + report_id,
877 aiptek->ifnum, buffer, size, 5000);
878}
879
880/***********************************************************************
881 * Send a command to the tablet.
882 */
883static int
884aiptek_command(struct aiptek *aiptek, unsigned char command, unsigned char data)
885{
886 const int sizeof_buf = 3 * sizeof(u8);
887 int ret;
888 u8 *buf;
889
890 buf = kmalloc(sizeof_buf, GFP_KERNEL);
891 if (!buf)
892 return -ENOMEM;
893
894 buf[0] = 2;
895 buf[1] = command;
896 buf[2] = data;
897
898 if ((ret =
899 aiptek_set_report(aiptek, 3, 2, buf, sizeof_buf)) != sizeof_buf) {
900 dev_dbg(&aiptek->intf->dev,
901 "aiptek_program: failed, tried to send: 0x%02x 0x%02x\n",
902 command, data);
903 }
904 kfree(buf);
905 return ret < 0 ? ret : 0;
906}
907
908/***********************************************************************
909 * Retrieve information from the tablet. Querying info is defined as first
910 * sending the {command,data} sequence as a command, followed by a wait
911 * (aka, "programmaticDelay") and then a "read" request.
912 */
913static int
914aiptek_query(struct aiptek *aiptek, unsigned char command, unsigned char data)
915{
916 const int sizeof_buf = 3 * sizeof(u8);
917 int ret;
918 u8 *buf;
919
920 buf = kmalloc(sizeof_buf, GFP_KERNEL);
921 if (!buf)
922 return -ENOMEM;
923
924 buf[0] = 2;
925 buf[1] = command;
926 buf[2] = data;
927
928 if (aiptek_command(aiptek, command, data) != 0) {
929 kfree(buf);
930 return -EIO;
931 }
932 msleep(aiptek->curSetting.programmableDelay);
933
934 if (aiptek_get_report(aiptek, 3, 2, buf, sizeof_buf) != sizeof_buf) {
935 dev_dbg(&aiptek->intf->dev,
936 "aiptek_query failed: returned 0x%02x 0x%02x 0x%02x\n",
937 buf[0], buf[1], buf[2]);
938 ret = -EIO;
939 } else {
940 ret = get_unaligned_le16(buf + 1);
941 }
942 kfree(buf);
943 return ret;
944}
945
946/***********************************************************************
947 * Program the tablet into either absolute or relative mode.
948 * We also get information about the tablet's size.
949 */
950static int aiptek_program_tablet(struct aiptek *aiptek)
951{
952 int ret;
953 /* Execute Resolution500LPI */
954 if ((ret = aiptek_command(aiptek, 0x18, 0x04)) < 0)
955 return ret;
956
957 /* Query getModelCode */
958 if ((ret = aiptek_query(aiptek, 0x02, 0x00)) < 0)
959 return ret;
960 aiptek->features.modelCode = ret & 0xff;
961
962 /* Query getODMCode */
963 if ((ret = aiptek_query(aiptek, 0x03, 0x00)) < 0)
964 return ret;
965 aiptek->features.odmCode = ret;
966
967 /* Query getFirmwareCode */
968 if ((ret = aiptek_query(aiptek, 0x04, 0x00)) < 0)
969 return ret;
970 aiptek->features.firmwareCode = ret;
971
972 /* Query getXextension */
973 if ((ret = aiptek_query(aiptek, 0x01, 0x00)) < 0)
974 return ret;
975 input_set_abs_params(aiptek->inputdev, ABS_X, 0, ret - 1, 0, 0);
976
977 /* Query getYextension */
978 if ((ret = aiptek_query(aiptek, 0x01, 0x01)) < 0)
979 return ret;
980 input_set_abs_params(aiptek->inputdev, ABS_Y, 0, ret - 1, 0, 0);
981
982 /* Query getPressureLevels */
983 if ((ret = aiptek_query(aiptek, 0x08, 0x00)) < 0)
984 return ret;
985 input_set_abs_params(aiptek->inputdev, ABS_PRESSURE, 0, ret - 1, 0, 0);
986
987 /* Depending on whether we are in absolute or relative mode, we will
988 * do a switchToTablet(absolute) or switchToMouse(relative) command.
989 */
990 if (aiptek->curSetting.coordinateMode ==
991 AIPTEK_COORDINATE_ABSOLUTE_MODE) {
992 /* Execute switchToTablet */
993 if ((ret = aiptek_command(aiptek, 0x10, 0x01)) < 0) {
994 return ret;
995 }
996 } else {
997 /* Execute switchToMouse */
998 if ((ret = aiptek_command(aiptek, 0x10, 0x00)) < 0) {
999 return ret;
1000 }
1001 }
1002
1003 /* Enable the macro keys */
1004 if ((ret = aiptek_command(aiptek, 0x11, 0x02)) < 0)
1005 return ret;
1006#if 0
1007 /* Execute FilterOn */
1008 if ((ret = aiptek_command(aiptek, 0x17, 0x00)) < 0)
1009 return ret;
1010#endif
1011
1012 /* Execute AutoGainOn */
1013 if ((ret = aiptek_command(aiptek, 0x12, 0xff)) < 0)
1014 return ret;
1015
1016 /* Reset the eventCount, so we track events from last (re)programming
1017 */
1018 aiptek->diagnostic = AIPTEK_DIAGNOSTIC_NA;
1019 aiptek->eventCount = 0;
1020
1021 return 0;
1022}
1023
1024/***********************************************************************
1025 * Sysfs functions. Sysfs prefers that individually-tunable parameters
1026 * exist in their separate pseudo-files. Summary data that is immutable
1027 * may exist in a singular file so long as you don't define a writeable
1028 * interface.
1029 */
1030
1031/***********************************************************************
1032 * support the 'size' file -- display support
1033 */
1034static ssize_t show_tabletSize(struct device *dev, struct device_attribute *attr, char *buf)
1035{
1036 struct aiptek *aiptek = dev_get_drvdata(dev);
1037
1038 return sysfs_emit(buf, "%dx%d\n",
1039 input_abs_get_max(aiptek->inputdev, ABS_X) + 1,
1040 input_abs_get_max(aiptek->inputdev, ABS_Y) + 1);
1041}
1042
1043/* These structs define the sysfs files, param #1 is the name of the
1044 * file, param 2 is the file permissions, param 3 & 4 are to the
1045 * output generator and input parser routines. Absence of a routine is
1046 * permitted -- it only means can't either 'cat' the file, or send data
1047 * to it.
1048 */
1049static DEVICE_ATTR(size, S_IRUGO, show_tabletSize, NULL);
1050
1051/***********************************************************************
1052 * support routines for the 'pointer_mode' file. Note that this file
1053 * both displays current setting and allows reprogramming.
1054 */
1055static struct aiptek_map pointer_mode_map[] = {
1056 { "stylus", AIPTEK_POINTER_ONLY_STYLUS_MODE },
1057 { "mouse", AIPTEK_POINTER_ONLY_MOUSE_MODE },
1058 { "either", AIPTEK_POINTER_EITHER_MODE },
1059 { NULL, AIPTEK_INVALID_VALUE }
1060};
1061
1062static ssize_t show_tabletPointerMode(struct device *dev, struct device_attribute *attr, char *buf)
1063{
1064 struct aiptek *aiptek = dev_get_drvdata(dev);
1065
1066 return sysfs_emit(buf, "%s\n", map_val_to_str(pointer_mode_map,
1067 aiptek->curSetting.pointerMode));
1068}
1069
1070static ssize_t
1071store_tabletPointerMode(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1072{
1073 struct aiptek *aiptek = dev_get_drvdata(dev);
1074 int new_mode = map_str_to_val(pointer_mode_map, buf, count);
1075
1076 if (new_mode == AIPTEK_INVALID_VALUE)
1077 return -EINVAL;
1078
1079 aiptek->newSetting.pointerMode = new_mode;
1080 return count;
1081}
1082
1083static DEVICE_ATTR(pointer_mode,
1084 S_IRUGO | S_IWUSR,
1085 show_tabletPointerMode, store_tabletPointerMode);
1086
1087/***********************************************************************
1088 * support routines for the 'coordinate_mode' file. Note that this file
1089 * both displays current setting and allows reprogramming.
1090 */
1091
1092static struct aiptek_map coordinate_mode_map[] = {
1093 { "absolute", AIPTEK_COORDINATE_ABSOLUTE_MODE },
1094 { "relative", AIPTEK_COORDINATE_RELATIVE_MODE },
1095 { NULL, AIPTEK_INVALID_VALUE }
1096};
1097
1098static ssize_t show_tabletCoordinateMode(struct device *dev, struct device_attribute *attr, char *buf)
1099{
1100 struct aiptek *aiptek = dev_get_drvdata(dev);
1101
1102 return sysfs_emit(buf, "%s\n", map_val_to_str(coordinate_mode_map,
1103 aiptek->curSetting.coordinateMode));
1104}
1105
1106static ssize_t
1107store_tabletCoordinateMode(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1108{
1109 struct aiptek *aiptek = dev_get_drvdata(dev);
1110 int new_mode = map_str_to_val(coordinate_mode_map, buf, count);
1111
1112 if (new_mode == AIPTEK_INVALID_VALUE)
1113 return -EINVAL;
1114
1115 aiptek->newSetting.coordinateMode = new_mode;
1116 return count;
1117}
1118
1119static DEVICE_ATTR(coordinate_mode,
1120 S_IRUGO | S_IWUSR,
1121 show_tabletCoordinateMode, store_tabletCoordinateMode);
1122
1123/***********************************************************************
1124 * support routines for the 'tool_mode' file. Note that this file
1125 * both displays current setting and allows reprogramming.
1126 */
1127
1128static struct aiptek_map tool_mode_map[] = {
1129 { "mouse", AIPTEK_TOOL_BUTTON_MOUSE_MODE },
1130 { "eraser", AIPTEK_TOOL_BUTTON_ERASER_MODE },
1131 { "pencil", AIPTEK_TOOL_BUTTON_PENCIL_MODE },
1132 { "pen", AIPTEK_TOOL_BUTTON_PEN_MODE },
1133 { "brush", AIPTEK_TOOL_BUTTON_BRUSH_MODE },
1134 { "airbrush", AIPTEK_TOOL_BUTTON_AIRBRUSH_MODE },
1135 { "lens", AIPTEK_TOOL_BUTTON_LENS_MODE },
1136 { NULL, AIPTEK_INVALID_VALUE }
1137};
1138
1139static ssize_t show_tabletToolMode(struct device *dev, struct device_attribute *attr, char *buf)
1140{
1141 struct aiptek *aiptek = dev_get_drvdata(dev);
1142
1143 return sysfs_emit(buf, "%s\n", map_val_to_str(tool_mode_map,
1144 aiptek->curSetting.toolMode));
1145}
1146
1147static ssize_t
1148store_tabletToolMode(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1149{
1150 struct aiptek *aiptek = dev_get_drvdata(dev);
1151 int new_mode = map_str_to_val(tool_mode_map, buf, count);
1152
1153 if (new_mode == AIPTEK_INVALID_VALUE)
1154 return -EINVAL;
1155
1156 aiptek->newSetting.toolMode = new_mode;
1157 return count;
1158}
1159
1160static DEVICE_ATTR(tool_mode,
1161 S_IRUGO | S_IWUSR,
1162 show_tabletToolMode, store_tabletToolMode);
1163
1164/***********************************************************************
1165 * support routines for the 'xtilt' file. Note that this file
1166 * both displays current setting and allows reprogramming.
1167 */
1168static ssize_t show_tabletXtilt(struct device *dev, struct device_attribute *attr, char *buf)
1169{
1170 struct aiptek *aiptek = dev_get_drvdata(dev);
1171
1172 if (aiptek->curSetting.xTilt == AIPTEK_TILT_DISABLE) {
1173 return sysfs_emit(buf, "disable\n");
1174 } else {
1175 return sysfs_emit(buf, "%d\n", aiptek->curSetting.xTilt);
1176 }
1177}
1178
1179static ssize_t
1180store_tabletXtilt(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1181{
1182 struct aiptek *aiptek = dev_get_drvdata(dev);
1183 int x;
1184
1185 if (kstrtoint(buf, 10, &x)) {
1186 size_t len = buf[count - 1] == '\n' ? count - 1 : count;
1187
1188 if (strncmp(buf, "disable", len))
1189 return -EINVAL;
1190
1191 aiptek->newSetting.xTilt = AIPTEK_TILT_DISABLE;
1192 } else {
1193 if (x < AIPTEK_TILT_MIN || x > AIPTEK_TILT_MAX)
1194 return -EINVAL;
1195
1196 aiptek->newSetting.xTilt = x;
1197 }
1198
1199 return count;
1200}
1201
1202static DEVICE_ATTR(xtilt,
1203 S_IRUGO | S_IWUSR, show_tabletXtilt, store_tabletXtilt);
1204
1205/***********************************************************************
1206 * support routines for the 'ytilt' file. Note that this file
1207 * both displays current setting and allows reprogramming.
1208 */
1209static ssize_t show_tabletYtilt(struct device *dev, struct device_attribute *attr, char *buf)
1210{
1211 struct aiptek *aiptek = dev_get_drvdata(dev);
1212
1213 if (aiptek->curSetting.yTilt == AIPTEK_TILT_DISABLE) {
1214 return sysfs_emit(buf, "disable\n");
1215 } else {
1216 return sysfs_emit(buf, "%d\n", aiptek->curSetting.yTilt);
1217 }
1218}
1219
1220static ssize_t
1221store_tabletYtilt(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1222{
1223 struct aiptek *aiptek = dev_get_drvdata(dev);
1224 int y;
1225
1226 if (kstrtoint(buf, 10, &y)) {
1227 size_t len = buf[count - 1] == '\n' ? count - 1 : count;
1228
1229 if (strncmp(buf, "disable", len))
1230 return -EINVAL;
1231
1232 aiptek->newSetting.yTilt = AIPTEK_TILT_DISABLE;
1233 } else {
1234 if (y < AIPTEK_TILT_MIN || y > AIPTEK_TILT_MAX)
1235 return -EINVAL;
1236
1237 aiptek->newSetting.yTilt = y;
1238 }
1239
1240 return count;
1241}
1242
1243static DEVICE_ATTR(ytilt,
1244 S_IRUGO | S_IWUSR, show_tabletYtilt, store_tabletYtilt);
1245
1246/***********************************************************************
1247 * support routines for the 'jitter' file. Note that this file
1248 * both displays current setting and allows reprogramming.
1249 */
1250static ssize_t show_tabletJitterDelay(struct device *dev, struct device_attribute *attr, char *buf)
1251{
1252 struct aiptek *aiptek = dev_get_drvdata(dev);
1253
1254 return sysfs_emit(buf, "%d\n", aiptek->curSetting.jitterDelay);
1255}
1256
1257static ssize_t
1258store_tabletJitterDelay(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1259{
1260 struct aiptek *aiptek = dev_get_drvdata(dev);
1261 int err, j;
1262
1263 err = kstrtoint(buf, 10, &j);
1264 if (err)
1265 return err;
1266
1267 aiptek->newSetting.jitterDelay = j;
1268 return count;
1269}
1270
1271static DEVICE_ATTR(jitter,
1272 S_IRUGO | S_IWUSR,
1273 show_tabletJitterDelay, store_tabletJitterDelay);
1274
1275/***********************************************************************
1276 * support routines for the 'delay' file. Note that this file
1277 * both displays current setting and allows reprogramming.
1278 */
1279static ssize_t show_tabletProgrammableDelay(struct device *dev, struct device_attribute *attr, char *buf)
1280{
1281 struct aiptek *aiptek = dev_get_drvdata(dev);
1282
1283 return sysfs_emit(buf, "%d\n", aiptek->curSetting.programmableDelay);
1284}
1285
1286static ssize_t
1287store_tabletProgrammableDelay(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1288{
1289 struct aiptek *aiptek = dev_get_drvdata(dev);
1290 int err, d;
1291
1292 err = kstrtoint(buf, 10, &d);
1293 if (err)
1294 return err;
1295
1296 aiptek->newSetting.programmableDelay = d;
1297 return count;
1298}
1299
1300static DEVICE_ATTR(delay,
1301 S_IRUGO | S_IWUSR,
1302 show_tabletProgrammableDelay, store_tabletProgrammableDelay);
1303
1304/***********************************************************************
1305 * support routines for the 'event_count' file. Note that this file
1306 * only displays current setting.
1307 */
1308static ssize_t show_tabletEventsReceived(struct device *dev, struct device_attribute *attr, char *buf)
1309{
1310 struct aiptek *aiptek = dev_get_drvdata(dev);
1311
1312 return sysfs_emit(buf, "%ld\n", aiptek->eventCount);
1313}
1314
1315static DEVICE_ATTR(event_count, S_IRUGO, show_tabletEventsReceived, NULL);
1316
1317/***********************************************************************
1318 * support routines for the 'diagnostic' file. Note that this file
1319 * only displays current setting.
1320 */
1321static ssize_t show_tabletDiagnosticMessage(struct device *dev, struct device_attribute *attr, char *buf)
1322{
1323 struct aiptek *aiptek = dev_get_drvdata(dev);
1324 char *retMsg;
1325
1326 switch (aiptek->diagnostic) {
1327 case AIPTEK_DIAGNOSTIC_NA:
1328 retMsg = "no errors\n";
1329 break;
1330
1331 case AIPTEK_DIAGNOSTIC_SENDING_RELATIVE_IN_ABSOLUTE:
1332 retMsg = "Error: receiving relative reports\n";
1333 break;
1334
1335 case AIPTEK_DIAGNOSTIC_SENDING_ABSOLUTE_IN_RELATIVE:
1336 retMsg = "Error: receiving absolute reports\n";
1337 break;
1338
1339 case AIPTEK_DIAGNOSTIC_TOOL_DISALLOWED:
1340 if (aiptek->curSetting.pointerMode ==
1341 AIPTEK_POINTER_ONLY_MOUSE_MODE) {
1342 retMsg = "Error: receiving stylus reports\n";
1343 } else {
1344 retMsg = "Error: receiving mouse reports\n";
1345 }
1346 break;
1347
1348 default:
1349 return 0;
1350 }
1351 return sysfs_emit(buf, retMsg);
1352}
1353
1354static DEVICE_ATTR(diagnostic, S_IRUGO, show_tabletDiagnosticMessage, NULL);
1355
1356/***********************************************************************
1357 * support routines for the 'stylus_upper' file. Note that this file
1358 * both displays current setting and allows for setting changing.
1359 */
1360
1361static struct aiptek_map stylus_button_map[] = {
1362 { "upper", AIPTEK_STYLUS_UPPER_BUTTON },
1363 { "lower", AIPTEK_STYLUS_LOWER_BUTTON },
1364 { NULL, AIPTEK_INVALID_VALUE }
1365};
1366
1367static ssize_t show_tabletStylusUpper(struct device *dev, struct device_attribute *attr, char *buf)
1368{
1369 struct aiptek *aiptek = dev_get_drvdata(dev);
1370
1371 return sysfs_emit(buf, "%s\n", map_val_to_str(stylus_button_map,
1372 aiptek->curSetting.stylusButtonUpper));
1373}
1374
1375static ssize_t
1376store_tabletStylusUpper(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1377{
1378 struct aiptek *aiptek = dev_get_drvdata(dev);
1379 int new_button = map_str_to_val(stylus_button_map, buf, count);
1380
1381 if (new_button == AIPTEK_INVALID_VALUE)
1382 return -EINVAL;
1383
1384 aiptek->newSetting.stylusButtonUpper = new_button;
1385 return count;
1386}
1387
1388static DEVICE_ATTR(stylus_upper,
1389 S_IRUGO | S_IWUSR,
1390 show_tabletStylusUpper, store_tabletStylusUpper);
1391
1392/***********************************************************************
1393 * support routines for the 'stylus_lower' file. Note that this file
1394 * both displays current setting and allows for setting changing.
1395 */
1396
1397static ssize_t show_tabletStylusLower(struct device *dev, struct device_attribute *attr, char *buf)
1398{
1399 struct aiptek *aiptek = dev_get_drvdata(dev);
1400
1401 return sysfs_emit(buf, "%s\n", map_val_to_str(stylus_button_map,
1402 aiptek->curSetting.stylusButtonLower));
1403}
1404
1405static ssize_t
1406store_tabletStylusLower(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1407{
1408 struct aiptek *aiptek = dev_get_drvdata(dev);
1409 int new_button = map_str_to_val(stylus_button_map, buf, count);
1410
1411 if (new_button == AIPTEK_INVALID_VALUE)
1412 return -EINVAL;
1413
1414 aiptek->newSetting.stylusButtonLower = new_button;
1415 return count;
1416}
1417
1418static DEVICE_ATTR(stylus_lower,
1419 S_IRUGO | S_IWUSR,
1420 show_tabletStylusLower, store_tabletStylusLower);
1421
1422/***********************************************************************
1423 * support routines for the 'mouse_left' file. Note that this file
1424 * both displays current setting and allows for setting changing.
1425 */
1426
1427static struct aiptek_map mouse_button_map[] = {
1428 { "left", AIPTEK_MOUSE_LEFT_BUTTON },
1429 { "middle", AIPTEK_MOUSE_MIDDLE_BUTTON },
1430 { "right", AIPTEK_MOUSE_RIGHT_BUTTON },
1431 { NULL, AIPTEK_INVALID_VALUE }
1432};
1433
1434static ssize_t show_tabletMouseLeft(struct device *dev, struct device_attribute *attr, char *buf)
1435{
1436 struct aiptek *aiptek = dev_get_drvdata(dev);
1437
1438 return sysfs_emit(buf, "%s\n", map_val_to_str(mouse_button_map,
1439 aiptek->curSetting.mouseButtonLeft));
1440}
1441
1442static ssize_t
1443store_tabletMouseLeft(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1444{
1445 struct aiptek *aiptek = dev_get_drvdata(dev);
1446 int new_button = map_str_to_val(mouse_button_map, buf, count);
1447
1448 if (new_button == AIPTEK_INVALID_VALUE)
1449 return -EINVAL;
1450
1451 aiptek->newSetting.mouseButtonLeft = new_button;
1452 return count;
1453}
1454
1455static DEVICE_ATTR(mouse_left,
1456 S_IRUGO | S_IWUSR,
1457 show_tabletMouseLeft, store_tabletMouseLeft);
1458
1459/***********************************************************************
1460 * support routines for the 'mouse_middle' file. Note that this file
1461 * both displays current setting and allows for setting changing.
1462 */
1463static ssize_t show_tabletMouseMiddle(struct device *dev, struct device_attribute *attr, char *buf)
1464{
1465 struct aiptek *aiptek = dev_get_drvdata(dev);
1466
1467 return sysfs_emit(buf, "%s\n", map_val_to_str(mouse_button_map,
1468 aiptek->curSetting.mouseButtonMiddle));
1469}
1470
1471static ssize_t
1472store_tabletMouseMiddle(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1473{
1474 struct aiptek *aiptek = dev_get_drvdata(dev);
1475 int new_button = map_str_to_val(mouse_button_map, buf, count);
1476
1477 if (new_button == AIPTEK_INVALID_VALUE)
1478 return -EINVAL;
1479
1480 aiptek->newSetting.mouseButtonMiddle = new_button;
1481 return count;
1482}
1483
1484static DEVICE_ATTR(mouse_middle,
1485 S_IRUGO | S_IWUSR,
1486 show_tabletMouseMiddle, store_tabletMouseMiddle);
1487
1488/***********************************************************************
1489 * support routines for the 'mouse_right' file. Note that this file
1490 * both displays current setting and allows for setting changing.
1491 */
1492static ssize_t show_tabletMouseRight(struct device *dev, struct device_attribute *attr, char *buf)
1493{
1494 struct aiptek *aiptek = dev_get_drvdata(dev);
1495
1496 return sysfs_emit(buf, "%s\n", map_val_to_str(mouse_button_map,
1497 aiptek->curSetting.mouseButtonRight));
1498}
1499
1500static ssize_t
1501store_tabletMouseRight(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1502{
1503 struct aiptek *aiptek = dev_get_drvdata(dev);
1504 int new_button = map_str_to_val(mouse_button_map, buf, count);
1505
1506 if (new_button == AIPTEK_INVALID_VALUE)
1507 return -EINVAL;
1508
1509 aiptek->newSetting.mouseButtonRight = new_button;
1510 return count;
1511}
1512
1513static DEVICE_ATTR(mouse_right,
1514 S_IRUGO | S_IWUSR,
1515 show_tabletMouseRight, store_tabletMouseRight);
1516
1517/***********************************************************************
1518 * support routines for the 'wheel' file. Note that this file
1519 * both displays current setting and allows for setting changing.
1520 */
1521static ssize_t show_tabletWheel(struct device *dev, struct device_attribute *attr, char *buf)
1522{
1523 struct aiptek *aiptek = dev_get_drvdata(dev);
1524
1525 if (aiptek->curSetting.wheel == AIPTEK_WHEEL_DISABLE) {
1526 return sysfs_emit(buf, "disable\n");
1527 } else {
1528 return sysfs_emit(buf, "%d\n", aiptek->curSetting.wheel);
1529 }
1530}
1531
1532static ssize_t
1533store_tabletWheel(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1534{
1535 struct aiptek *aiptek = dev_get_drvdata(dev);
1536 int err, w;
1537
1538 err = kstrtoint(buf, 10, &w);
1539 if (err)
1540 return err;
1541
1542 aiptek->newSetting.wheel = w;
1543 return count;
1544}
1545
1546static DEVICE_ATTR(wheel,
1547 S_IRUGO | S_IWUSR, show_tabletWheel, store_tabletWheel);
1548
1549/***********************************************************************
1550 * support routines for the 'execute' file. Note that this file
1551 * both displays current setting and allows for setting changing.
1552 */
1553static ssize_t show_tabletExecute(struct device *dev, struct device_attribute *attr, char *buf)
1554{
1555 /* There is nothing useful to display, so a one-line manual
1556 * is in order...
1557 */
1558 return sysfs_emit(buf, "Write anything to this file to program your tablet.\n");
1559}
1560
1561static ssize_t
1562store_tabletExecute(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1563{
1564 struct aiptek *aiptek = dev_get_drvdata(dev);
1565
1566 /* We do not care what you write to this file. Merely the action
1567 * of writing to this file triggers a tablet reprogramming.
1568 */
1569 memcpy(&aiptek->curSetting, &aiptek->newSetting,
1570 sizeof(struct aiptek_settings));
1571
1572 if (aiptek_program_tablet(aiptek) < 0)
1573 return -EIO;
1574
1575 return count;
1576}
1577
1578static DEVICE_ATTR(execute,
1579 S_IRUGO | S_IWUSR, show_tabletExecute, store_tabletExecute);
1580
1581/***********************************************************************
1582 * support routines for the 'odm_code' file. Note that this file
1583 * only displays current setting.
1584 */
1585static ssize_t show_tabletODMCode(struct device *dev, struct device_attribute *attr, char *buf)
1586{
1587 struct aiptek *aiptek = dev_get_drvdata(dev);
1588
1589 return sysfs_emit(buf, "0x%04x\n", aiptek->features.odmCode);
1590}
1591
1592static DEVICE_ATTR(odm_code, S_IRUGO, show_tabletODMCode, NULL);
1593
1594/***********************************************************************
1595 * support routines for the 'model_code' file. Note that this file
1596 * only displays current setting.
1597 */
1598static ssize_t show_tabletModelCode(struct device *dev, struct device_attribute *attr, char *buf)
1599{
1600 struct aiptek *aiptek = dev_get_drvdata(dev);
1601
1602 return sysfs_emit(buf, "0x%04x\n", aiptek->features.modelCode);
1603}
1604
1605static DEVICE_ATTR(model_code, S_IRUGO, show_tabletModelCode, NULL);
1606
1607/***********************************************************************
1608 * support routines for the 'firmware_code' file. Note that this file
1609 * only displays current setting.
1610 */
1611static ssize_t show_firmwareCode(struct device *dev, struct device_attribute *attr, char *buf)
1612{
1613 struct aiptek *aiptek = dev_get_drvdata(dev);
1614
1615 return sysfs_emit(buf, "%04x\n", aiptek->features.firmwareCode);
1616}
1617
1618static DEVICE_ATTR(firmware_code, S_IRUGO, show_firmwareCode, NULL);
1619
1620static struct attribute *aiptek_dev_attrs[] = {
1621 &dev_attr_size.attr,
1622 &dev_attr_pointer_mode.attr,
1623 &dev_attr_coordinate_mode.attr,
1624 &dev_attr_tool_mode.attr,
1625 &dev_attr_xtilt.attr,
1626 &dev_attr_ytilt.attr,
1627 &dev_attr_jitter.attr,
1628 &dev_attr_delay.attr,
1629 &dev_attr_event_count.attr,
1630 &dev_attr_diagnostic.attr,
1631 &dev_attr_odm_code.attr,
1632 &dev_attr_model_code.attr,
1633 &dev_attr_firmware_code.attr,
1634 &dev_attr_stylus_lower.attr,
1635 &dev_attr_stylus_upper.attr,
1636 &dev_attr_mouse_left.attr,
1637 &dev_attr_mouse_middle.attr,
1638 &dev_attr_mouse_right.attr,
1639 &dev_attr_wheel.attr,
1640 &dev_attr_execute.attr,
1641 NULL
1642};
1643
1644ATTRIBUTE_GROUPS(aiptek_dev);
1645
1646/***********************************************************************
1647 * This routine is called when a tablet has been identified. It basically
1648 * sets up the tablet and the driver's internal structures.
1649 */
1650static int
1651aiptek_probe(struct usb_interface *intf, const struct usb_device_id *id)
1652{
1653 struct usb_device *usbdev = interface_to_usbdev(intf);
1654 struct usb_endpoint_descriptor *endpoint;
1655 struct aiptek *aiptek;
1656 struct input_dev *inputdev;
1657 int i;
1658 int speeds[] = { 0,
1659 AIPTEK_PROGRAMMABLE_DELAY_50,
1660 AIPTEK_PROGRAMMABLE_DELAY_400,
1661 AIPTEK_PROGRAMMABLE_DELAY_25,
1662 AIPTEK_PROGRAMMABLE_DELAY_100,
1663 AIPTEK_PROGRAMMABLE_DELAY_200,
1664 AIPTEK_PROGRAMMABLE_DELAY_300
1665 };
1666 int err = -ENOMEM;
1667
1668 /* programmableDelay is where the command-line specified
1669 * delay is kept. We make it the first element of speeds[],
1670 * so therefore, your override speed is tried first, then the
1671 * remainder. Note that the default value of 400ms will be tried
1672 * if you do not specify any command line parameter.
1673 */
1674 speeds[0] = programmableDelay;
1675
1676 aiptek = kzalloc(sizeof(struct aiptek), GFP_KERNEL);
1677 inputdev = input_allocate_device();
1678 if (!aiptek || !inputdev) {
1679 dev_warn(&intf->dev,
1680 "cannot allocate memory or input device\n");
1681 goto fail1;
1682 }
1683
1684 aiptek->data = usb_alloc_coherent(usbdev, AIPTEK_PACKET_LENGTH,
1685 GFP_KERNEL, &aiptek->data_dma);
1686 if (!aiptek->data) {
1687 dev_warn(&intf->dev, "cannot allocate usb buffer\n");
1688 goto fail1;
1689 }
1690
1691 aiptek->urb = usb_alloc_urb(0, GFP_KERNEL);
1692 if (!aiptek->urb) {
1693 dev_warn(&intf->dev, "cannot allocate urb\n");
1694 goto fail2;
1695 }
1696
1697 aiptek->inputdev = inputdev;
1698 aiptek->intf = intf;
1699 aiptek->ifnum = intf->cur_altsetting->desc.bInterfaceNumber;
1700 aiptek->inDelay = 0;
1701 aiptek->endDelay = 0;
1702 aiptek->previousJitterable = 0;
1703 aiptek->lastMacro = -1;
1704
1705 /* Set up the curSettings struct. Said struct contains the current
1706 * programmable parameters. The newSetting struct contains changes
1707 * the user makes to the settings via the sysfs interface. Those
1708 * changes are not "committed" to curSettings until the user
1709 * writes to the sysfs/.../execute file.
1710 */
1711 aiptek->curSetting.pointerMode = AIPTEK_POINTER_EITHER_MODE;
1712 aiptek->curSetting.coordinateMode = AIPTEK_COORDINATE_ABSOLUTE_MODE;
1713 aiptek->curSetting.toolMode = AIPTEK_TOOL_BUTTON_PEN_MODE;
1714 aiptek->curSetting.xTilt = AIPTEK_TILT_DISABLE;
1715 aiptek->curSetting.yTilt = AIPTEK_TILT_DISABLE;
1716 aiptek->curSetting.mouseButtonLeft = AIPTEK_MOUSE_LEFT_BUTTON;
1717 aiptek->curSetting.mouseButtonMiddle = AIPTEK_MOUSE_MIDDLE_BUTTON;
1718 aiptek->curSetting.mouseButtonRight = AIPTEK_MOUSE_RIGHT_BUTTON;
1719 aiptek->curSetting.stylusButtonUpper = AIPTEK_STYLUS_UPPER_BUTTON;
1720 aiptek->curSetting.stylusButtonLower = AIPTEK_STYLUS_LOWER_BUTTON;
1721 aiptek->curSetting.jitterDelay = jitterDelay;
1722 aiptek->curSetting.programmableDelay = programmableDelay;
1723
1724 /* Both structs should have equivalent settings
1725 */
1726 aiptek->newSetting = aiptek->curSetting;
1727
1728 /* Determine the usb devices' physical path.
1729 * Asketh not why we always pretend we're using "../input0",
1730 * but I suspect this will have to be refactored one
1731 * day if a single USB device can be a keyboard & a mouse
1732 * & a tablet, and the inputX number actually will tell
1733 * us something...
1734 */
1735 usb_make_path(usbdev, aiptek->features.usbPath,
1736 sizeof(aiptek->features.usbPath));
1737 strlcat(aiptek->features.usbPath, "/input0",
1738 sizeof(aiptek->features.usbPath));
1739
1740 /* Set up client data, pointers to open and close routines
1741 * for the input device.
1742 */
1743 inputdev->name = "Aiptek";
1744 inputdev->phys = aiptek->features.usbPath;
1745 usb_to_input_id(usbdev, &inputdev->id);
1746 inputdev->dev.parent = &intf->dev;
1747
1748 input_set_drvdata(inputdev, aiptek);
1749
1750 inputdev->open = aiptek_open;
1751 inputdev->close = aiptek_close;
1752
1753 /* Now program the capacities of the tablet, in terms of being
1754 * an input device.
1755 */
1756 for (i = 0; i < ARRAY_SIZE(eventTypes); ++i)
1757 __set_bit(eventTypes[i], inputdev->evbit);
1758
1759 for (i = 0; i < ARRAY_SIZE(absEvents); ++i)
1760 __set_bit(absEvents[i], inputdev->absbit);
1761
1762 for (i = 0; i < ARRAY_SIZE(relEvents); ++i)
1763 __set_bit(relEvents[i], inputdev->relbit);
1764
1765 __set_bit(MSC_SERIAL, inputdev->mscbit);
1766
1767 /* Set up key and button codes */
1768 for (i = 0; i < ARRAY_SIZE(buttonEvents); ++i)
1769 __set_bit(buttonEvents[i], inputdev->keybit);
1770
1771 for (i = 0; i < ARRAY_SIZE(macroKeyEvents); ++i)
1772 __set_bit(macroKeyEvents[i], inputdev->keybit);
1773
1774 /*
1775 * Program the input device coordinate capacities. We do not yet
1776 * know what maximum X, Y, and Z values are, so we're putting fake
1777 * values in. Later, we'll ask the tablet to put in the correct
1778 * values.
1779 */
1780 input_set_abs_params(inputdev, ABS_X, 0, 2999, 0, 0);
1781 input_set_abs_params(inputdev, ABS_Y, 0, 2249, 0, 0);
1782 input_set_abs_params(inputdev, ABS_PRESSURE, 0, 511, 0, 0);
1783 input_set_abs_params(inputdev, ABS_TILT_X, AIPTEK_TILT_MIN, AIPTEK_TILT_MAX, 0, 0);
1784 input_set_abs_params(inputdev, ABS_TILT_Y, AIPTEK_TILT_MIN, AIPTEK_TILT_MAX, 0, 0);
1785 input_set_abs_params(inputdev, ABS_WHEEL, AIPTEK_WHEEL_MIN, AIPTEK_WHEEL_MAX - 1, 0, 0);
1786
1787 err = usb_find_common_endpoints(intf->cur_altsetting,
1788 NULL, NULL, &endpoint, NULL);
1789 if (err) {
1790 dev_err(&intf->dev,
1791 "interface has no int in endpoints, but must have minimum 1\n");
1792 goto fail3;
1793 }
1794
1795 /* Go set up our URB, which is called when the tablet receives
1796 * input.
1797 */
1798 usb_fill_int_urb(aiptek->urb,
1799 usbdev,
1800 usb_rcvintpipe(usbdev,
1801 endpoint->bEndpointAddress),
1802 aiptek->data, 8, aiptek_irq, aiptek,
1803 endpoint->bInterval);
1804
1805 aiptek->urb->transfer_dma = aiptek->data_dma;
1806 aiptek->urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
1807
1808 /* Program the tablet. This sets the tablet up in the mode
1809 * specified in newSetting, and also queries the tablet's
1810 * physical capacities.
1811 *
1812 * Sanity check: if a tablet doesn't like the slow programmatic
1813 * delay, we often get sizes of 0x0. Let's use that as an indicator
1814 * to try faster delays, up to 25 ms. If that logic fails, well, you'll
1815 * have to explain to us how your tablet thinks it's 0x0, and yet that's
1816 * not an error :-)
1817 */
1818
1819 for (i = 0; i < ARRAY_SIZE(speeds); ++i) {
1820 aiptek->curSetting.programmableDelay = speeds[i];
1821 (void)aiptek_program_tablet(aiptek);
1822 if (input_abs_get_max(aiptek->inputdev, ABS_X) > 0) {
1823 dev_info(&intf->dev,
1824 "Aiptek using %d ms programming speed\n",
1825 aiptek->curSetting.programmableDelay);
1826 break;
1827 }
1828 }
1829
1830 /* Murphy says that some day someone will have a tablet that fails the
1831 above test. That's you, Frederic Rodrigo */
1832 if (i == ARRAY_SIZE(speeds)) {
1833 dev_info(&intf->dev,
1834 "Aiptek tried all speeds, no sane response\n");
1835 err = -EINVAL;
1836 goto fail3;
1837 }
1838
1839 /* Associate this driver's struct with the usb interface.
1840 */
1841 usb_set_intfdata(intf, aiptek);
1842
1843 /* Register the tablet as an Input Device
1844 */
1845 err = input_register_device(aiptek->inputdev);
1846 if (err) {
1847 dev_warn(&intf->dev,
1848 "input_register_device returned err: %d\n", err);
1849 goto fail3;
1850 }
1851 return 0;
1852
1853 fail3: usb_free_urb(aiptek->urb);
1854 fail2: usb_free_coherent(usbdev, AIPTEK_PACKET_LENGTH, aiptek->data,
1855 aiptek->data_dma);
1856 fail1: usb_set_intfdata(intf, NULL);
1857 input_free_device(inputdev);
1858 kfree(aiptek);
1859 return err;
1860}
1861
1862/***********************************************************************
1863 * Deal with tablet disconnecting from the system.
1864 */
1865static void aiptek_disconnect(struct usb_interface *intf)
1866{
1867 struct aiptek *aiptek = usb_get_intfdata(intf);
1868
1869 /* Disassociate driver's struct with usb interface
1870 */
1871 usb_set_intfdata(intf, NULL);
1872 if (aiptek != NULL) {
1873 /* Free & unhook everything from the system.
1874 */
1875 usb_kill_urb(aiptek->urb);
1876 input_unregister_device(aiptek->inputdev);
1877 usb_free_urb(aiptek->urb);
1878 usb_free_coherent(interface_to_usbdev(intf),
1879 AIPTEK_PACKET_LENGTH,
1880 aiptek->data, aiptek->data_dma);
1881 kfree(aiptek);
1882 }
1883}
1884
1885static struct usb_driver aiptek_driver = {
1886 .name = "aiptek",
1887 .probe = aiptek_probe,
1888 .disconnect = aiptek_disconnect,
1889 .id_table = aiptek_ids,
1890 .dev_groups = aiptek_dev_groups,
1891};
1892
1893module_usb_driver(aiptek_driver);
1894
1895MODULE_AUTHOR("Bryan W. Headley/Chris Atenasio/Cedric Brun/Rene van Paassen");
1896MODULE_DESCRIPTION("Aiptek HyperPen USB Tablet Driver");
1897MODULE_LICENSE("GPL");
1898
1899module_param(programmableDelay, int, 0);
1900MODULE_PARM_DESC(programmableDelay, "delay used during tablet programming");
1901module_param(jitterDelay, int, 0);
1902MODULE_PARM_DESC(jitterDelay, "stylus/mouse settlement delay");
1/*
2 * Native support for the Aiptek HyperPen USB Tablets
3 * (4000U/5000U/6000U/8000U/12000U)
4 *
5 * Copyright (c) 2001 Chris Atenasio <chris@crud.net>
6 * Copyright (c) 2002-2004 Bryan W. Headley <bwheadley@earthlink.net>
7 *
8 * based on wacom.c by
9 * Vojtech Pavlik <vojtech@suse.cz>
10 * Andreas Bach Aaen <abach@stofanet.dk>
11 * Clifford Wolf <clifford@clifford.at>
12 * Sam Mosel <sam.mosel@computer.org>
13 * James E. Blair <corvus@gnu.org>
14 * Daniel Egger <egger@suse.de>
15 *
16 * Many thanks to Oliver Kuechemann for his support.
17 *
18 * ChangeLog:
19 * v0.1 - Initial release
20 * v0.2 - Hack to get around fake event 28's. (Bryan W. Headley)
21 * v0.3 - Make URB dynamic (Bryan W. Headley, Jun-8-2002)
22 * Released to Linux 2.4.19 and 2.5.x
23 * v0.4 - Rewrote substantial portions of the code to deal with
24 * corrected control sequences, timing, dynamic configuration,
25 * support of 6000U - 12000U, procfs, and macro key support
26 * (Jan-1-2003 - Feb-5-2003, Bryan W. Headley)
27 * v1.0 - Added support for diagnostic messages, count of messages
28 * received from URB - Mar-8-2003, Bryan W. Headley
29 * v1.1 - added support for tablet resolution, changed DV and proximity
30 * some corrections - Jun-22-2003, martin schneebacher
31 * - Added support for the sysfs interface, deprecating the
32 * procfs interface for 2.5.x kernel. Also added support for
33 * Wheel command. Bryan W. Headley July-15-2003.
34 * v1.2 - Reworked jitter timer as a kernel thread.
35 * Bryan W. Headley November-28-2003/Jan-10-2004.
36 * v1.3 - Repaired issue of kernel thread going nuts on single-processor
37 * machines, introduced programmableDelay as a command line
38 * parameter. Feb 7 2004, Bryan W. Headley.
39 * v1.4 - Re-wire jitter so it does not require a thread. Courtesy of
40 * Rene van Paassen. Added reporting of physical pointer device
41 * (e.g., stylus, mouse in reports 2, 3, 4, 5. We don't know
42 * for reports 1, 6.)
43 * what physical device reports for reports 1, 6.) Also enabled
44 * MOUSE and LENS tool button modes. Renamed "rubber" to "eraser".
45 * Feb 20, 2004, Bryan W. Headley.
46 * v1.5 - Added previousJitterable, so we don't do jitter delay when the
47 * user is holding a button down for periods of time.
48 *
49 * NOTE:
50 * This kernel driver is augmented by the "Aiptek" XFree86 input
51 * driver for your X server, as well as the Gaiptek GUI Front-end
52 * "Tablet Manager".
53 * These three products are highly interactive with one another,
54 * so therefore it's easier to document them all as one subsystem.
55 * Please visit the project's "home page", located at,
56 * http://aiptektablet.sourceforge.net.
57 *
58 * This program is free software; you can redistribute it and/or modify
59 * it under the terms of the GNU General Public License as published by
60 * the Free Software Foundation; either version 2 of the License, or
61 * (at your option) any later version.
62 *
63 * This program is distributed in the hope that it will be useful,
64 * but WITHOUT ANY WARRANTY; without even the implied warranty of
65 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
66 * GNU General Public License for more details.
67 *
68 * You should have received a copy of the GNU General Public License
69 * along with this program; if not, write to the Free Software
70 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
71 */
72
73#include <linux/jiffies.h>
74#include <linux/kernel.h>
75#include <linux/slab.h>
76#include <linux/module.h>
77#include <linux/usb/input.h>
78#include <linux/uaccess.h>
79#include <asm/unaligned.h>
80
81/*
82 * Aiptek status packet:
83 *
84 * (returned as Report 1 - relative coordinates from mouse and stylus)
85 *
86 * bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
87 * byte0 0 0 0 0 0 0 0 1
88 * byte1 0 0 0 0 0 BS2 BS Tip
89 * byte2 X7 X6 X5 X4 X3 X2 X1 X0
90 * byte3 Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
91 *
92 * (returned as Report 2 - absolute coordinates from the stylus)
93 *
94 * bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
95 * byte0 0 0 0 0 0 0 1 0
96 * byte1 X7 X6 X5 X4 X3 X2 X1 X0
97 * byte2 X15 X14 X13 X12 X11 X10 X9 X8
98 * byte3 Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
99 * byte4 Y15 Y14 Y13 Y12 Y11 Y10 Y9 Y8
100 * byte5 * * * BS2 BS1 Tip IR DV
101 * byte6 P7 P6 P5 P4 P3 P2 P1 P0
102 * byte7 P15 P14 P13 P12 P11 P10 P9 P8
103 *
104 * (returned as Report 3 - absolute coordinates from the mouse)
105 *
106 * bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
107 * byte0 0 0 0 0 0 0 1 1
108 * byte1 X7 X6 X5 X4 X3 X2 X1 X0
109 * byte2 X15 X14 X13 X12 X11 X10 X9 X8
110 * byte3 Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
111 * byte4 Y15 Y14 Y13 Y12 Y11 Y10 Y9 Y8
112 * byte5 * * * BS2 BS1 Tip IR DV
113 * byte6 P7 P6 P5 P4 P3 P2 P1 P0
114 * byte7 P15 P14 P13 P12 P11 P10 P9 P8
115 *
116 * (returned as Report 4 - macrokeys from the stylus)
117 *
118 * bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
119 * byte0 0 0 0 0 0 1 0 0
120 * byte1 0 0 0 BS2 BS Tip IR DV
121 * byte2 0 0 0 0 0 0 1 0
122 * byte3 0 0 0 K4 K3 K2 K1 K0
123 * byte4 P7 P6 P5 P4 P3 P2 P1 P0
124 * byte5 P15 P14 P13 P12 P11 P10 P9 P8
125 *
126 * (returned as Report 5 - macrokeys from the mouse)
127 *
128 * bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
129 * byte0 0 0 0 0 0 1 0 1
130 * byte1 0 0 0 BS2 BS Tip IR DV
131 * byte2 0 0 0 0 0 0 1 0
132 * byte3 0 0 0 K4 K3 K2 K1 K0
133 * byte4 P7 P6 P5 P4 P3 P2 P1 P0
134 * byte5 P15 P14 P13 P12 P11 P10 P9 P8
135 *
136 * IR: In Range = Proximity on
137 * DV = Data Valid
138 * BS = Barrel Switch (as in, macro keys)
139 * BS2 also referred to as Tablet Pick
140 *
141 * Command Summary:
142 *
143 * Use report_type CONTROL (3)
144 * Use report_id 2
145 *
146 * Command/Data Description Return Bytes Return Value
147 * 0x10/0x00 SwitchToMouse 0
148 * 0x10/0x01 SwitchToTablet 0
149 * 0x18/0x04 SetResolution 0
150 * 0x12/0xFF AutoGainOn 0
151 * 0x17/0x00 FilterOn 0
152 * 0x01/0x00 GetXExtension 2 MaxX
153 * 0x01/0x01 GetYExtension 2 MaxY
154 * 0x02/0x00 GetModelCode 2 ModelCode = LOBYTE
155 * 0x03/0x00 GetODMCode 2 ODMCode
156 * 0x08/0x00 GetPressureLevels 2 =512
157 * 0x04/0x00 GetFirmwareVersion 2 Firmware Version
158 * 0x11/0x02 EnableMacroKeys 0
159 *
160 * To initialize the tablet:
161 *
162 * (1) Send Resolution500LPI (Command)
163 * (2) Query for Model code (Option Report)
164 * (3) Query for ODM code (Option Report)
165 * (4) Query for firmware (Option Report)
166 * (5) Query for GetXExtension (Option Report)
167 * (6) Query for GetYExtension (Option Report)
168 * (7) Query for GetPressureLevels (Option Report)
169 * (8) SwitchToTablet for Absolute coordinates, or
170 * SwitchToMouse for Relative coordinates (Command)
171 * (9) EnableMacroKeys (Command)
172 * (10) FilterOn (Command)
173 * (11) AutoGainOn (Command)
174 *
175 * (Step 9 can be omitted, but you'll then have no function keys.)
176 */
177
178#define USB_VENDOR_ID_AIPTEK 0x08ca
179#define USB_VENDOR_ID_KYE 0x0458
180#define USB_REQ_GET_REPORT 0x01
181#define USB_REQ_SET_REPORT 0x09
182
183 /* PointerMode codes
184 */
185#define AIPTEK_POINTER_ONLY_MOUSE_MODE 0
186#define AIPTEK_POINTER_ONLY_STYLUS_MODE 1
187#define AIPTEK_POINTER_EITHER_MODE 2
188
189#define AIPTEK_POINTER_ALLOW_MOUSE_MODE(a) \
190 (a == AIPTEK_POINTER_ONLY_MOUSE_MODE || \
191 a == AIPTEK_POINTER_EITHER_MODE)
192#define AIPTEK_POINTER_ALLOW_STYLUS_MODE(a) \
193 (a == AIPTEK_POINTER_ONLY_STYLUS_MODE || \
194 a == AIPTEK_POINTER_EITHER_MODE)
195
196 /* CoordinateMode code
197 */
198#define AIPTEK_COORDINATE_RELATIVE_MODE 0
199#define AIPTEK_COORDINATE_ABSOLUTE_MODE 1
200
201 /* XTilt and YTilt values
202 */
203#define AIPTEK_TILT_MIN (-128)
204#define AIPTEK_TILT_MAX 127
205#define AIPTEK_TILT_DISABLE (-10101)
206
207 /* Wheel values
208 */
209#define AIPTEK_WHEEL_MIN 0
210#define AIPTEK_WHEEL_MAX 1024
211#define AIPTEK_WHEEL_DISABLE (-10101)
212
213 /* ToolCode values, which BTW are 0x140 .. 0x14f
214 * We have things set up such that if the tool button has changed,
215 * the tools get reset.
216 */
217 /* toolMode codes
218 */
219#define AIPTEK_TOOL_BUTTON_PEN_MODE BTN_TOOL_PEN
220#define AIPTEK_TOOL_BUTTON_PENCIL_MODE BTN_TOOL_PENCIL
221#define AIPTEK_TOOL_BUTTON_BRUSH_MODE BTN_TOOL_BRUSH
222#define AIPTEK_TOOL_BUTTON_AIRBRUSH_MODE BTN_TOOL_AIRBRUSH
223#define AIPTEK_TOOL_BUTTON_ERASER_MODE BTN_TOOL_RUBBER
224#define AIPTEK_TOOL_BUTTON_MOUSE_MODE BTN_TOOL_MOUSE
225#define AIPTEK_TOOL_BUTTON_LENS_MODE BTN_TOOL_LENS
226
227 /* Diagnostic message codes
228 */
229#define AIPTEK_DIAGNOSTIC_NA 0
230#define AIPTEK_DIAGNOSTIC_SENDING_RELATIVE_IN_ABSOLUTE 1
231#define AIPTEK_DIAGNOSTIC_SENDING_ABSOLUTE_IN_RELATIVE 2
232#define AIPTEK_DIAGNOSTIC_TOOL_DISALLOWED 3
233
234 /* Time to wait (in ms) to help mask hand jittering
235 * when pressing the stylus buttons.
236 */
237#define AIPTEK_JITTER_DELAY_DEFAULT 50
238
239 /* Time to wait (in ms) in-between sending the tablet
240 * a command and beginning the process of reading the return
241 * sequence from the tablet.
242 */
243#define AIPTEK_PROGRAMMABLE_DELAY_25 25
244#define AIPTEK_PROGRAMMABLE_DELAY_50 50
245#define AIPTEK_PROGRAMMABLE_DELAY_100 100
246#define AIPTEK_PROGRAMMABLE_DELAY_200 200
247#define AIPTEK_PROGRAMMABLE_DELAY_300 300
248#define AIPTEK_PROGRAMMABLE_DELAY_400 400
249#define AIPTEK_PROGRAMMABLE_DELAY_DEFAULT AIPTEK_PROGRAMMABLE_DELAY_400
250
251 /* Mouse button programming
252 */
253#define AIPTEK_MOUSE_LEFT_BUTTON 0x04
254#define AIPTEK_MOUSE_RIGHT_BUTTON 0x08
255#define AIPTEK_MOUSE_MIDDLE_BUTTON 0x10
256
257 /* Stylus button programming
258 */
259#define AIPTEK_STYLUS_LOWER_BUTTON 0x08
260#define AIPTEK_STYLUS_UPPER_BUTTON 0x10
261
262 /* Length of incoming packet from the tablet
263 */
264#define AIPTEK_PACKET_LENGTH 8
265
266 /* We report in EV_MISC both the proximity and
267 * whether the report came from the stylus, tablet mouse
268 * or "unknown" -- Unknown when the tablet is in relative
269 * mode, because we only get report 1's.
270 */
271#define AIPTEK_REPORT_TOOL_UNKNOWN 0x10
272#define AIPTEK_REPORT_TOOL_STYLUS 0x20
273#define AIPTEK_REPORT_TOOL_MOUSE 0x40
274
275static int programmableDelay = AIPTEK_PROGRAMMABLE_DELAY_DEFAULT;
276static int jitterDelay = AIPTEK_JITTER_DELAY_DEFAULT;
277
278struct aiptek_features {
279 int odmCode; /* Tablet manufacturer code */
280 int modelCode; /* Tablet model code (not unique) */
281 int firmwareCode; /* prom/eeprom version */
282 char usbPath[64 + 1]; /* device's physical usb path */
283};
284
285struct aiptek_settings {
286 int pointerMode; /* stylus-, mouse-only or either */
287 int coordinateMode; /* absolute/relative coords */
288 int toolMode; /* pen, pencil, brush, etc. tool */
289 int xTilt; /* synthetic xTilt amount */
290 int yTilt; /* synthetic yTilt amount */
291 int wheel; /* synthetic wheel amount */
292 int stylusButtonUpper; /* stylus upper btn delivers... */
293 int stylusButtonLower; /* stylus lower btn delivers... */
294 int mouseButtonLeft; /* mouse left btn delivers... */
295 int mouseButtonMiddle; /* mouse middle btn delivers... */
296 int mouseButtonRight; /* mouse right btn delivers... */
297 int programmableDelay; /* delay for tablet programming */
298 int jitterDelay; /* delay for hand jittering */
299};
300
301struct aiptek {
302 struct input_dev *inputdev; /* input device struct */
303 struct usb_interface *intf; /* usb interface struct */
304 struct urb *urb; /* urb for incoming reports */
305 dma_addr_t data_dma; /* our dma stuffage */
306 struct aiptek_features features; /* tablet's array of features */
307 struct aiptek_settings curSetting; /* tablet's current programmable */
308 struct aiptek_settings newSetting; /* ... and new param settings */
309 unsigned int ifnum; /* interface number for IO */
310 int diagnostic; /* tablet diagnostic codes */
311 unsigned long eventCount; /* event count */
312 int inDelay; /* jitter: in jitter delay? */
313 unsigned long endDelay; /* jitter: time when delay ends */
314 int previousJitterable; /* jitterable prev value */
315
316 int lastMacro; /* macro key to reset */
317 int previousToolMode; /* pen, pencil, brush, etc. tool */
318 unsigned char *data; /* incoming packet data */
319};
320
321static const int eventTypes[] = {
322 EV_KEY, EV_ABS, EV_REL, EV_MSC,
323};
324
325static const int absEvents[] = {
326 ABS_X, ABS_Y, ABS_PRESSURE, ABS_TILT_X, ABS_TILT_Y,
327 ABS_WHEEL, ABS_MISC,
328};
329
330static const int relEvents[] = {
331 REL_X, REL_Y, REL_WHEEL,
332};
333
334static const int buttonEvents[] = {
335 BTN_LEFT, BTN_RIGHT, BTN_MIDDLE,
336 BTN_TOOL_PEN, BTN_TOOL_RUBBER, BTN_TOOL_PENCIL, BTN_TOOL_AIRBRUSH,
337 BTN_TOOL_BRUSH, BTN_TOOL_MOUSE, BTN_TOOL_LENS, BTN_TOUCH,
338 BTN_STYLUS, BTN_STYLUS2,
339};
340
341/*
342 * Permit easy lookup of keyboard events to send, versus
343 * the bitmap which comes from the tablet. This hides the
344 * issue that the F_keys are not sequentially numbered.
345 */
346static const int macroKeyEvents[] = {
347 KEY_ESC, KEY_F1, KEY_F2, KEY_F3, KEY_F4, KEY_F5,
348 KEY_F6, KEY_F7, KEY_F8, KEY_F9, KEY_F10, KEY_F11,
349 KEY_F12, KEY_F13, KEY_F14, KEY_F15, KEY_F16, KEY_F17,
350 KEY_F18, KEY_F19, KEY_F20, KEY_F21, KEY_F22, KEY_F23,
351 KEY_F24, KEY_STOP, KEY_AGAIN, KEY_PROPS, KEY_UNDO,
352 KEY_FRONT, KEY_COPY, KEY_OPEN, KEY_PASTE, 0
353};
354
355/***********************************************************************
356 * Map values to strings and back. Every map should have the following
357 * as its last element: { NULL, AIPTEK_INVALID_VALUE }.
358 */
359#define AIPTEK_INVALID_VALUE -1
360
361struct aiptek_map {
362 const char *string;
363 int value;
364};
365
366static int map_str_to_val(const struct aiptek_map *map, const char *str, size_t count)
367{
368 const struct aiptek_map *p;
369
370 if (str[count - 1] == '\n')
371 count--;
372
373 for (p = map; p->string; p++)
374 if (!strncmp(str, p->string, count))
375 return p->value;
376
377 return AIPTEK_INVALID_VALUE;
378}
379
380static const char *map_val_to_str(const struct aiptek_map *map, int val)
381{
382 const struct aiptek_map *p;
383
384 for (p = map; p->value != AIPTEK_INVALID_VALUE; p++)
385 if (val == p->value)
386 return p->string;
387
388 return "unknown";
389}
390
391/***********************************************************************
392 * aiptek_irq can receive one of six potential reports.
393 * The documentation for each is in the body of the function.
394 *
395 * The tablet reports on several attributes per invocation of
396 * aiptek_irq. Because the Linux Input Event system allows the
397 * transmission of ONE attribute per input_report_xxx() call,
398 * collation has to be done on the other end to reconstitute
399 * a complete tablet report. Further, the number of Input Event reports
400 * submitted varies, depending on what USB report type, and circumstance.
401 * To deal with this, EV_MSC is used to indicate an 'end-of-report'
402 * message. This has been an undocumented convention understood by the kernel
403 * tablet driver and clients such as gpm and XFree86's tablet drivers.
404 *
405 * Of the information received from the tablet, the one piece I
406 * cannot transmit is the proximity bit (without resorting to an EV_MSC
407 * convention above.) I therefore have taken over REL_MISC and ABS_MISC
408 * (for relative and absolute reports, respectively) for communicating
409 * Proximity. Why two events? I thought it interesting to know if the
410 * Proximity event occurred while the tablet was in absolute or relative
411 * mode.
412 * Update: REL_MISC proved not to be such a good idea. With REL_MISC you
413 * get an event transmitted each time. ABS_MISC works better, since it
414 * can be set and re-set. Thus, only using ABS_MISC from now on.
415 *
416 * Other tablets use the notion of a certain minimum stylus pressure
417 * to infer proximity. While that could have been done, that is yet
418 * another 'by convention' behavior, the documentation for which
419 * would be spread between two (or more) pieces of software.
420 *
421 * EV_MSC usage was terminated for this purpose in Linux 2.5.x, and
422 * replaced with the input_sync() method (which emits EV_SYN.)
423 */
424
425static void aiptek_irq(struct urb *urb)
426{
427 struct aiptek *aiptek = urb->context;
428 unsigned char *data = aiptek->data;
429 struct input_dev *inputdev = aiptek->inputdev;
430 struct usb_interface *intf = aiptek->intf;
431 int jitterable = 0;
432 int retval, macro, x, y, z, left, right, middle, p, dv, tip, bs, pck;
433
434 switch (urb->status) {
435 case 0:
436 /* Success */
437 break;
438
439 case -ECONNRESET:
440 case -ENOENT:
441 case -ESHUTDOWN:
442 /* This urb is terminated, clean up */
443 dev_dbg(&intf->dev, "%s - urb shutting down with status: %d\n",
444 __func__, urb->status);
445 return;
446
447 default:
448 dev_dbg(&intf->dev, "%s - nonzero urb status received: %d\n",
449 __func__, urb->status);
450 goto exit;
451 }
452
453 /* See if we are in a delay loop -- throw out report if true.
454 */
455 if (aiptek->inDelay == 1 && time_after(aiptek->endDelay, jiffies)) {
456 goto exit;
457 }
458
459 aiptek->inDelay = 0;
460 aiptek->eventCount++;
461
462 /* Report 1 delivers relative coordinates with either a stylus
463 * or the mouse. You do not know, however, which input
464 * tool generated the event.
465 */
466 if (data[0] == 1) {
467 if (aiptek->curSetting.coordinateMode ==
468 AIPTEK_COORDINATE_ABSOLUTE_MODE) {
469 aiptek->diagnostic =
470 AIPTEK_DIAGNOSTIC_SENDING_RELATIVE_IN_ABSOLUTE;
471 } else {
472 x = (signed char) data[2];
473 y = (signed char) data[3];
474
475 /* jitterable keeps track of whether any button has been pressed.
476 * We're also using it to remap the physical mouse button mask
477 * to pseudo-settings. (We don't specifically care about it's
478 * value after moving/transposing mouse button bitmasks, except
479 * that a non-zero value indicates that one or more
480 * mouse button was pressed.)
481 */
482 jitterable = data[1] & 0x07;
483
484 left = (data[1] & aiptek->curSetting.mouseButtonLeft >> 2) != 0 ? 1 : 0;
485 right = (data[1] & aiptek->curSetting.mouseButtonRight >> 2) != 0 ? 1 : 0;
486 middle = (data[1] & aiptek->curSetting.mouseButtonMiddle >> 2) != 0 ? 1 : 0;
487
488 input_report_key(inputdev, BTN_LEFT, left);
489 input_report_key(inputdev, BTN_MIDDLE, middle);
490 input_report_key(inputdev, BTN_RIGHT, right);
491
492 input_report_abs(inputdev, ABS_MISC,
493 1 | AIPTEK_REPORT_TOOL_UNKNOWN);
494 input_report_rel(inputdev, REL_X, x);
495 input_report_rel(inputdev, REL_Y, y);
496
497 /* Wheel support is in the form of a single-event
498 * firing.
499 */
500 if (aiptek->curSetting.wheel != AIPTEK_WHEEL_DISABLE) {
501 input_report_rel(inputdev, REL_WHEEL,
502 aiptek->curSetting.wheel);
503 aiptek->curSetting.wheel = AIPTEK_WHEEL_DISABLE;
504 }
505 if (aiptek->lastMacro != -1) {
506 input_report_key(inputdev,
507 macroKeyEvents[aiptek->lastMacro], 0);
508 aiptek->lastMacro = -1;
509 }
510 input_sync(inputdev);
511 }
512 }
513 /* Report 2 is delivered only by the stylus, and delivers
514 * absolute coordinates.
515 */
516 else if (data[0] == 2) {
517 if (aiptek->curSetting.coordinateMode == AIPTEK_COORDINATE_RELATIVE_MODE) {
518 aiptek->diagnostic = AIPTEK_DIAGNOSTIC_SENDING_ABSOLUTE_IN_RELATIVE;
519 } else if (!AIPTEK_POINTER_ALLOW_STYLUS_MODE
520 (aiptek->curSetting.pointerMode)) {
521 aiptek->diagnostic = AIPTEK_DIAGNOSTIC_TOOL_DISALLOWED;
522 } else {
523 x = get_unaligned_le16(data + 1);
524 y = get_unaligned_le16(data + 3);
525 z = get_unaligned_le16(data + 6);
526
527 dv = (data[5] & 0x01) != 0 ? 1 : 0;
528 p = (data[5] & 0x02) != 0 ? 1 : 0;
529 tip = (data[5] & 0x04) != 0 ? 1 : 0;
530
531 /* Use jitterable to re-arrange button masks
532 */
533 jitterable = data[5] & 0x18;
534
535 bs = (data[5] & aiptek->curSetting.stylusButtonLower) != 0 ? 1 : 0;
536 pck = (data[5] & aiptek->curSetting.stylusButtonUpper) != 0 ? 1 : 0;
537
538 /* dv indicates 'data valid' (e.g., the tablet is in sync
539 * and has delivered a "correct" report) We will ignore
540 * all 'bad' reports...
541 */
542 if (dv != 0) {
543 /* If the selected tool changed, reset the old
544 * tool key, and set the new one.
545 */
546 if (aiptek->previousToolMode !=
547 aiptek->curSetting.toolMode) {
548 input_report_key(inputdev,
549 aiptek->previousToolMode, 0);
550 input_report_key(inputdev,
551 aiptek->curSetting.toolMode,
552 1);
553 aiptek->previousToolMode =
554 aiptek->curSetting.toolMode;
555 }
556
557 if (p != 0) {
558 input_report_abs(inputdev, ABS_X, x);
559 input_report_abs(inputdev, ABS_Y, y);
560 input_report_abs(inputdev, ABS_PRESSURE, z);
561
562 input_report_key(inputdev, BTN_TOUCH, tip);
563 input_report_key(inputdev, BTN_STYLUS, bs);
564 input_report_key(inputdev, BTN_STYLUS2, pck);
565
566 if (aiptek->curSetting.xTilt !=
567 AIPTEK_TILT_DISABLE) {
568 input_report_abs(inputdev,
569 ABS_TILT_X,
570 aiptek->curSetting.xTilt);
571 }
572 if (aiptek->curSetting.yTilt != AIPTEK_TILT_DISABLE) {
573 input_report_abs(inputdev,
574 ABS_TILT_Y,
575 aiptek->curSetting.yTilt);
576 }
577
578 /* Wheel support is in the form of a single-event
579 * firing.
580 */
581 if (aiptek->curSetting.wheel !=
582 AIPTEK_WHEEL_DISABLE) {
583 input_report_abs(inputdev,
584 ABS_WHEEL,
585 aiptek->curSetting.wheel);
586 aiptek->curSetting.wheel = AIPTEK_WHEEL_DISABLE;
587 }
588 }
589 input_report_abs(inputdev, ABS_MISC, p | AIPTEK_REPORT_TOOL_STYLUS);
590 if (aiptek->lastMacro != -1) {
591 input_report_key(inputdev,
592 macroKeyEvents[aiptek->lastMacro], 0);
593 aiptek->lastMacro = -1;
594 }
595 input_sync(inputdev);
596 }
597 }
598 }
599 /* Report 3's come from the mouse in absolute mode.
600 */
601 else if (data[0] == 3) {
602 if (aiptek->curSetting.coordinateMode == AIPTEK_COORDINATE_RELATIVE_MODE) {
603 aiptek->diagnostic = AIPTEK_DIAGNOSTIC_SENDING_ABSOLUTE_IN_RELATIVE;
604 } else if (!AIPTEK_POINTER_ALLOW_MOUSE_MODE
605 (aiptek->curSetting.pointerMode)) {
606 aiptek->diagnostic = AIPTEK_DIAGNOSTIC_TOOL_DISALLOWED;
607 } else {
608 x = get_unaligned_le16(data + 1);
609 y = get_unaligned_le16(data + 3);
610
611 jitterable = data[5] & 0x1c;
612
613 dv = (data[5] & 0x01) != 0 ? 1 : 0;
614 p = (data[5] & 0x02) != 0 ? 1 : 0;
615 left = (data[5] & aiptek->curSetting.mouseButtonLeft) != 0 ? 1 : 0;
616 right = (data[5] & aiptek->curSetting.mouseButtonRight) != 0 ? 1 : 0;
617 middle = (data[5] & aiptek->curSetting.mouseButtonMiddle) != 0 ? 1 : 0;
618
619 if (dv != 0) {
620 /* If the selected tool changed, reset the old
621 * tool key, and set the new one.
622 */
623 if (aiptek->previousToolMode !=
624 aiptek->curSetting.toolMode) {
625 input_report_key(inputdev,
626 aiptek->previousToolMode, 0);
627 input_report_key(inputdev,
628 aiptek->curSetting.toolMode,
629 1);
630 aiptek->previousToolMode =
631 aiptek->curSetting.toolMode;
632 }
633
634 if (p != 0) {
635 input_report_abs(inputdev, ABS_X, x);
636 input_report_abs(inputdev, ABS_Y, y);
637
638 input_report_key(inputdev, BTN_LEFT, left);
639 input_report_key(inputdev, BTN_MIDDLE, middle);
640 input_report_key(inputdev, BTN_RIGHT, right);
641
642 /* Wheel support is in the form of a single-event
643 * firing.
644 */
645 if (aiptek->curSetting.wheel != AIPTEK_WHEEL_DISABLE) {
646 input_report_abs(inputdev,
647 ABS_WHEEL,
648 aiptek->curSetting.wheel);
649 aiptek->curSetting.wheel = AIPTEK_WHEEL_DISABLE;
650 }
651 }
652 input_report_abs(inputdev, ABS_MISC, p | AIPTEK_REPORT_TOOL_MOUSE);
653 if (aiptek->lastMacro != -1) {
654 input_report_key(inputdev,
655 macroKeyEvents[aiptek->lastMacro], 0);
656 aiptek->lastMacro = -1;
657 }
658 input_sync(inputdev);
659 }
660 }
661 }
662 /* Report 4s come from the macro keys when pressed by stylus
663 */
664 else if (data[0] == 4) {
665 jitterable = data[1] & 0x18;
666
667 dv = (data[1] & 0x01) != 0 ? 1 : 0;
668 p = (data[1] & 0x02) != 0 ? 1 : 0;
669 tip = (data[1] & 0x04) != 0 ? 1 : 0;
670 bs = (data[1] & aiptek->curSetting.stylusButtonLower) != 0 ? 1 : 0;
671 pck = (data[1] & aiptek->curSetting.stylusButtonUpper) != 0 ? 1 : 0;
672
673 macro = dv && p && tip && !(data[3] & 1) ? (data[3] >> 1) : -1;
674 z = get_unaligned_le16(data + 4);
675
676 if (dv) {
677 /* If the selected tool changed, reset the old
678 * tool key, and set the new one.
679 */
680 if (aiptek->previousToolMode !=
681 aiptek->curSetting.toolMode) {
682 input_report_key(inputdev,
683 aiptek->previousToolMode, 0);
684 input_report_key(inputdev,
685 aiptek->curSetting.toolMode,
686 1);
687 aiptek->previousToolMode =
688 aiptek->curSetting.toolMode;
689 }
690 }
691
692 if (aiptek->lastMacro != -1 && aiptek->lastMacro != macro) {
693 input_report_key(inputdev, macroKeyEvents[aiptek->lastMacro], 0);
694 aiptek->lastMacro = -1;
695 }
696
697 if (macro != -1 && macro != aiptek->lastMacro) {
698 input_report_key(inputdev, macroKeyEvents[macro], 1);
699 aiptek->lastMacro = macro;
700 }
701 input_report_abs(inputdev, ABS_MISC,
702 p | AIPTEK_REPORT_TOOL_STYLUS);
703 input_sync(inputdev);
704 }
705 /* Report 5s come from the macro keys when pressed by mouse
706 */
707 else if (data[0] == 5) {
708 jitterable = data[1] & 0x1c;
709
710 dv = (data[1] & 0x01) != 0 ? 1 : 0;
711 p = (data[1] & 0x02) != 0 ? 1 : 0;
712 left = (data[1]& aiptek->curSetting.mouseButtonLeft) != 0 ? 1 : 0;
713 right = (data[1] & aiptek->curSetting.mouseButtonRight) != 0 ? 1 : 0;
714 middle = (data[1] & aiptek->curSetting.mouseButtonMiddle) != 0 ? 1 : 0;
715 macro = dv && p && left && !(data[3] & 1) ? (data[3] >> 1) : 0;
716
717 if (dv) {
718 /* If the selected tool changed, reset the old
719 * tool key, and set the new one.
720 */
721 if (aiptek->previousToolMode !=
722 aiptek->curSetting.toolMode) {
723 input_report_key(inputdev,
724 aiptek->previousToolMode, 0);
725 input_report_key(inputdev,
726 aiptek->curSetting.toolMode, 1);
727 aiptek->previousToolMode = aiptek->curSetting.toolMode;
728 }
729 }
730
731 if (aiptek->lastMacro != -1 && aiptek->lastMacro != macro) {
732 input_report_key(inputdev, macroKeyEvents[aiptek->lastMacro], 0);
733 aiptek->lastMacro = -1;
734 }
735
736 if (macro != -1 && macro != aiptek->lastMacro) {
737 input_report_key(inputdev, macroKeyEvents[macro], 1);
738 aiptek->lastMacro = macro;
739 }
740
741 input_report_abs(inputdev, ABS_MISC,
742 p | AIPTEK_REPORT_TOOL_MOUSE);
743 input_sync(inputdev);
744 }
745 /* We have no idea which tool can generate a report 6. Theoretically,
746 * neither need to, having been given reports 4 & 5 for such use.
747 * However, report 6 is the 'official-looking' report for macroKeys;
748 * reports 4 & 5 supposively are used to support unnamed, unknown
749 * hat switches (which just so happen to be the macroKeys.)
750 */
751 else if (data[0] == 6) {
752 macro = get_unaligned_le16(data + 1);
753 if (macro > 0) {
754 input_report_key(inputdev, macroKeyEvents[macro - 1],
755 0);
756 }
757 if (macro < 25) {
758 input_report_key(inputdev, macroKeyEvents[macro + 1],
759 0);
760 }
761
762 /* If the selected tool changed, reset the old
763 tool key, and set the new one.
764 */
765 if (aiptek->previousToolMode !=
766 aiptek->curSetting.toolMode) {
767 input_report_key(inputdev,
768 aiptek->previousToolMode, 0);
769 input_report_key(inputdev,
770 aiptek->curSetting.toolMode,
771 1);
772 aiptek->previousToolMode =
773 aiptek->curSetting.toolMode;
774 }
775
776 input_report_key(inputdev, macroKeyEvents[macro], 1);
777 input_report_abs(inputdev, ABS_MISC,
778 1 | AIPTEK_REPORT_TOOL_UNKNOWN);
779 input_sync(inputdev);
780 } else {
781 dev_dbg(&intf->dev, "Unknown report %d\n", data[0]);
782 }
783
784 /* Jitter may occur when the user presses a button on the stlyus
785 * or the mouse. What we do to prevent that is wait 'x' milliseconds
786 * following a 'jitterable' event, which should give the hand some time
787 * stabilize itself.
788 *
789 * We just introduced aiptek->previousJitterable to carry forth the
790 * notion that jitter occurs when the button state changes from on to off:
791 * a person drawing, holding a button down is not subject to jittering.
792 * With that in mind, changing from upper button depressed to lower button
793 * WILL transition through a jitter delay.
794 */
795
796 if (aiptek->previousJitterable != jitterable &&
797 aiptek->curSetting.jitterDelay != 0 && aiptek->inDelay != 1) {
798 aiptek->endDelay = jiffies +
799 ((aiptek->curSetting.jitterDelay * HZ) / 1000);
800 aiptek->inDelay = 1;
801 }
802 aiptek->previousJitterable = jitterable;
803
804exit:
805 retval = usb_submit_urb(urb, GFP_ATOMIC);
806 if (retval != 0) {
807 dev_err(&intf->dev,
808 "%s - usb_submit_urb failed with result %d\n",
809 __func__, retval);
810 }
811}
812
813/***********************************************************************
814 * These are the USB id's known so far. We do not identify them to
815 * specific Aiptek model numbers, because there has been overlaps,
816 * use, and reuse of id's in existing models. Certain models have
817 * been known to use more than one ID, indicative perhaps of
818 * manufacturing revisions. In any event, we consider these
819 * IDs to not be model-specific nor unique.
820 */
821static const struct usb_device_id aiptek_ids[] = {
822 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x01)},
823 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x10)},
824 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x20)},
825 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x21)},
826 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x22)},
827 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x23)},
828 {USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x24)},
829 {USB_DEVICE(USB_VENDOR_ID_KYE, 0x5003)},
830 {}
831};
832
833MODULE_DEVICE_TABLE(usb, aiptek_ids);
834
835/***********************************************************************
836 * Open an instance of the tablet driver.
837 */
838static int aiptek_open(struct input_dev *inputdev)
839{
840 struct aiptek *aiptek = input_get_drvdata(inputdev);
841
842 aiptek->urb->dev = interface_to_usbdev(aiptek->intf);
843 if (usb_submit_urb(aiptek->urb, GFP_KERNEL) != 0)
844 return -EIO;
845
846 return 0;
847}
848
849/***********************************************************************
850 * Close an instance of the tablet driver.
851 */
852static void aiptek_close(struct input_dev *inputdev)
853{
854 struct aiptek *aiptek = input_get_drvdata(inputdev);
855
856 usb_kill_urb(aiptek->urb);
857}
858
859/***********************************************************************
860 * aiptek_set_report and aiptek_get_report() are borrowed from Linux 2.4.x,
861 * where they were known as usb_set_report and usb_get_report.
862 */
863static int
864aiptek_set_report(struct aiptek *aiptek,
865 unsigned char report_type,
866 unsigned char report_id, void *buffer, int size)
867{
868 struct usb_device *udev = interface_to_usbdev(aiptek->intf);
869
870 return usb_control_msg(udev,
871 usb_sndctrlpipe(udev, 0),
872 USB_REQ_SET_REPORT,
873 USB_TYPE_CLASS | USB_RECIP_INTERFACE |
874 USB_DIR_OUT, (report_type << 8) + report_id,
875 aiptek->ifnum, buffer, size, 5000);
876}
877
878static int
879aiptek_get_report(struct aiptek *aiptek,
880 unsigned char report_type,
881 unsigned char report_id, void *buffer, int size)
882{
883 struct usb_device *udev = interface_to_usbdev(aiptek->intf);
884
885 return usb_control_msg(udev,
886 usb_rcvctrlpipe(udev, 0),
887 USB_REQ_GET_REPORT,
888 USB_TYPE_CLASS | USB_RECIP_INTERFACE |
889 USB_DIR_IN, (report_type << 8) + report_id,
890 aiptek->ifnum, buffer, size, 5000);
891}
892
893/***********************************************************************
894 * Send a command to the tablet.
895 */
896static int
897aiptek_command(struct aiptek *aiptek, unsigned char command, unsigned char data)
898{
899 const int sizeof_buf = 3 * sizeof(u8);
900 int ret;
901 u8 *buf;
902
903 buf = kmalloc(sizeof_buf, GFP_KERNEL);
904 if (!buf)
905 return -ENOMEM;
906
907 buf[0] = 2;
908 buf[1] = command;
909 buf[2] = data;
910
911 if ((ret =
912 aiptek_set_report(aiptek, 3, 2, buf, sizeof_buf)) != sizeof_buf) {
913 dev_dbg(&aiptek->intf->dev,
914 "aiptek_program: failed, tried to send: 0x%02x 0x%02x\n",
915 command, data);
916 }
917 kfree(buf);
918 return ret < 0 ? ret : 0;
919}
920
921/***********************************************************************
922 * Retrieve information from the tablet. Querying info is defined as first
923 * sending the {command,data} sequence as a command, followed by a wait
924 * (aka, "programmaticDelay") and then a "read" request.
925 */
926static int
927aiptek_query(struct aiptek *aiptek, unsigned char command, unsigned char data)
928{
929 const int sizeof_buf = 3 * sizeof(u8);
930 int ret;
931 u8 *buf;
932
933 buf = kmalloc(sizeof_buf, GFP_KERNEL);
934 if (!buf)
935 return -ENOMEM;
936
937 buf[0] = 2;
938 buf[1] = command;
939 buf[2] = data;
940
941 if (aiptek_command(aiptek, command, data) != 0) {
942 kfree(buf);
943 return -EIO;
944 }
945 msleep(aiptek->curSetting.programmableDelay);
946
947 if ((ret =
948 aiptek_get_report(aiptek, 3, 2, buf, sizeof_buf)) != sizeof_buf) {
949 dev_dbg(&aiptek->intf->dev,
950 "aiptek_query failed: returned 0x%02x 0x%02x 0x%02x\n",
951 buf[0], buf[1], buf[2]);
952 ret = -EIO;
953 } else {
954 ret = get_unaligned_le16(buf + 1);
955 }
956 kfree(buf);
957 return ret;
958}
959
960/***********************************************************************
961 * Program the tablet into either absolute or relative mode.
962 * We also get information about the tablet's size.
963 */
964static int aiptek_program_tablet(struct aiptek *aiptek)
965{
966 int ret;
967 /* Execute Resolution500LPI */
968 if ((ret = aiptek_command(aiptek, 0x18, 0x04)) < 0)
969 return ret;
970
971 /* Query getModelCode */
972 if ((ret = aiptek_query(aiptek, 0x02, 0x00)) < 0)
973 return ret;
974 aiptek->features.modelCode = ret & 0xff;
975
976 /* Query getODMCode */
977 if ((ret = aiptek_query(aiptek, 0x03, 0x00)) < 0)
978 return ret;
979 aiptek->features.odmCode = ret;
980
981 /* Query getFirmwareCode */
982 if ((ret = aiptek_query(aiptek, 0x04, 0x00)) < 0)
983 return ret;
984 aiptek->features.firmwareCode = ret;
985
986 /* Query getXextension */
987 if ((ret = aiptek_query(aiptek, 0x01, 0x00)) < 0)
988 return ret;
989 input_set_abs_params(aiptek->inputdev, ABS_X, 0, ret - 1, 0, 0);
990
991 /* Query getYextension */
992 if ((ret = aiptek_query(aiptek, 0x01, 0x01)) < 0)
993 return ret;
994 input_set_abs_params(aiptek->inputdev, ABS_Y, 0, ret - 1, 0, 0);
995
996 /* Query getPressureLevels */
997 if ((ret = aiptek_query(aiptek, 0x08, 0x00)) < 0)
998 return ret;
999 input_set_abs_params(aiptek->inputdev, ABS_PRESSURE, 0, ret - 1, 0, 0);
1000
1001 /* Depending on whether we are in absolute or relative mode, we will
1002 * do a switchToTablet(absolute) or switchToMouse(relative) command.
1003 */
1004 if (aiptek->curSetting.coordinateMode ==
1005 AIPTEK_COORDINATE_ABSOLUTE_MODE) {
1006 /* Execute switchToTablet */
1007 if ((ret = aiptek_command(aiptek, 0x10, 0x01)) < 0) {
1008 return ret;
1009 }
1010 } else {
1011 /* Execute switchToMouse */
1012 if ((ret = aiptek_command(aiptek, 0x10, 0x00)) < 0) {
1013 return ret;
1014 }
1015 }
1016
1017 /* Enable the macro keys */
1018 if ((ret = aiptek_command(aiptek, 0x11, 0x02)) < 0)
1019 return ret;
1020#if 0
1021 /* Execute FilterOn */
1022 if ((ret = aiptek_command(aiptek, 0x17, 0x00)) < 0)
1023 return ret;
1024#endif
1025
1026 /* Execute AutoGainOn */
1027 if ((ret = aiptek_command(aiptek, 0x12, 0xff)) < 0)
1028 return ret;
1029
1030 /* Reset the eventCount, so we track events from last (re)programming
1031 */
1032 aiptek->diagnostic = AIPTEK_DIAGNOSTIC_NA;
1033 aiptek->eventCount = 0;
1034
1035 return 0;
1036}
1037
1038/***********************************************************************
1039 * Sysfs functions. Sysfs prefers that individually-tunable parameters
1040 * exist in their separate pseudo-files. Summary data that is immutable
1041 * may exist in a singular file so long as you don't define a writeable
1042 * interface.
1043 */
1044
1045/***********************************************************************
1046 * support the 'size' file -- display support
1047 */
1048static ssize_t show_tabletSize(struct device *dev, struct device_attribute *attr, char *buf)
1049{
1050 struct aiptek *aiptek = dev_get_drvdata(dev);
1051
1052 return snprintf(buf, PAGE_SIZE, "%dx%d\n",
1053 input_abs_get_max(aiptek->inputdev, ABS_X) + 1,
1054 input_abs_get_max(aiptek->inputdev, ABS_Y) + 1);
1055}
1056
1057/* These structs define the sysfs files, param #1 is the name of the
1058 * file, param 2 is the file permissions, param 3 & 4 are to the
1059 * output generator and input parser routines. Absence of a routine is
1060 * permitted -- it only means can't either 'cat' the file, or send data
1061 * to it.
1062 */
1063static DEVICE_ATTR(size, S_IRUGO, show_tabletSize, NULL);
1064
1065/***********************************************************************
1066 * support routines for the 'pointer_mode' file. Note that this file
1067 * both displays current setting and allows reprogramming.
1068 */
1069static struct aiptek_map pointer_mode_map[] = {
1070 { "stylus", AIPTEK_POINTER_ONLY_STYLUS_MODE },
1071 { "mouse", AIPTEK_POINTER_ONLY_MOUSE_MODE },
1072 { "either", AIPTEK_POINTER_EITHER_MODE },
1073 { NULL, AIPTEK_INVALID_VALUE }
1074};
1075
1076static ssize_t show_tabletPointerMode(struct device *dev, struct device_attribute *attr, char *buf)
1077{
1078 struct aiptek *aiptek = dev_get_drvdata(dev);
1079
1080 return snprintf(buf, PAGE_SIZE, "%s\n",
1081 map_val_to_str(pointer_mode_map,
1082 aiptek->curSetting.pointerMode));
1083}
1084
1085static ssize_t
1086store_tabletPointerMode(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1087{
1088 struct aiptek *aiptek = dev_get_drvdata(dev);
1089 int new_mode = map_str_to_val(pointer_mode_map, buf, count);
1090
1091 if (new_mode == AIPTEK_INVALID_VALUE)
1092 return -EINVAL;
1093
1094 aiptek->newSetting.pointerMode = new_mode;
1095 return count;
1096}
1097
1098static DEVICE_ATTR(pointer_mode,
1099 S_IRUGO | S_IWUSR,
1100 show_tabletPointerMode, store_tabletPointerMode);
1101
1102/***********************************************************************
1103 * support routines for the 'coordinate_mode' file. Note that this file
1104 * both displays current setting and allows reprogramming.
1105 */
1106
1107static struct aiptek_map coordinate_mode_map[] = {
1108 { "absolute", AIPTEK_COORDINATE_ABSOLUTE_MODE },
1109 { "relative", AIPTEK_COORDINATE_RELATIVE_MODE },
1110 { NULL, AIPTEK_INVALID_VALUE }
1111};
1112
1113static ssize_t show_tabletCoordinateMode(struct device *dev, struct device_attribute *attr, char *buf)
1114{
1115 struct aiptek *aiptek = dev_get_drvdata(dev);
1116
1117 return snprintf(buf, PAGE_SIZE, "%s\n",
1118 map_val_to_str(coordinate_mode_map,
1119 aiptek->curSetting.coordinateMode));
1120}
1121
1122static ssize_t
1123store_tabletCoordinateMode(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1124{
1125 struct aiptek *aiptek = dev_get_drvdata(dev);
1126 int new_mode = map_str_to_val(coordinate_mode_map, buf, count);
1127
1128 if (new_mode == AIPTEK_INVALID_VALUE)
1129 return -EINVAL;
1130
1131 aiptek->newSetting.coordinateMode = new_mode;
1132 return count;
1133}
1134
1135static DEVICE_ATTR(coordinate_mode,
1136 S_IRUGO | S_IWUSR,
1137 show_tabletCoordinateMode, store_tabletCoordinateMode);
1138
1139/***********************************************************************
1140 * support routines for the 'tool_mode' file. Note that this file
1141 * both displays current setting and allows reprogramming.
1142 */
1143
1144static struct aiptek_map tool_mode_map[] = {
1145 { "mouse", AIPTEK_TOOL_BUTTON_MOUSE_MODE },
1146 { "eraser", AIPTEK_TOOL_BUTTON_ERASER_MODE },
1147 { "pencil", AIPTEK_TOOL_BUTTON_PENCIL_MODE },
1148 { "pen", AIPTEK_TOOL_BUTTON_PEN_MODE },
1149 { "brush", AIPTEK_TOOL_BUTTON_BRUSH_MODE },
1150 { "airbrush", AIPTEK_TOOL_BUTTON_AIRBRUSH_MODE },
1151 { "lens", AIPTEK_TOOL_BUTTON_LENS_MODE },
1152 { NULL, AIPTEK_INVALID_VALUE }
1153};
1154
1155static ssize_t show_tabletToolMode(struct device *dev, struct device_attribute *attr, char *buf)
1156{
1157 struct aiptek *aiptek = dev_get_drvdata(dev);
1158
1159 return snprintf(buf, PAGE_SIZE, "%s\n",
1160 map_val_to_str(tool_mode_map,
1161 aiptek->curSetting.toolMode));
1162}
1163
1164static ssize_t
1165store_tabletToolMode(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1166{
1167 struct aiptek *aiptek = dev_get_drvdata(dev);
1168 int new_mode = map_str_to_val(tool_mode_map, buf, count);
1169
1170 if (new_mode == AIPTEK_INVALID_VALUE)
1171 return -EINVAL;
1172
1173 aiptek->newSetting.toolMode = new_mode;
1174 return count;
1175}
1176
1177static DEVICE_ATTR(tool_mode,
1178 S_IRUGO | S_IWUSR,
1179 show_tabletToolMode, store_tabletToolMode);
1180
1181/***********************************************************************
1182 * support routines for the 'xtilt' file. Note that this file
1183 * both displays current setting and allows reprogramming.
1184 */
1185static ssize_t show_tabletXtilt(struct device *dev, struct device_attribute *attr, char *buf)
1186{
1187 struct aiptek *aiptek = dev_get_drvdata(dev);
1188
1189 if (aiptek->curSetting.xTilt == AIPTEK_TILT_DISABLE) {
1190 return snprintf(buf, PAGE_SIZE, "disable\n");
1191 } else {
1192 return snprintf(buf, PAGE_SIZE, "%d\n",
1193 aiptek->curSetting.xTilt);
1194 }
1195}
1196
1197static ssize_t
1198store_tabletXtilt(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1199{
1200 struct aiptek *aiptek = dev_get_drvdata(dev);
1201 int x;
1202
1203 if (kstrtoint(buf, 10, &x)) {
1204 size_t len = buf[count - 1] == '\n' ? count - 1 : count;
1205
1206 if (strncmp(buf, "disable", len))
1207 return -EINVAL;
1208
1209 aiptek->newSetting.xTilt = AIPTEK_TILT_DISABLE;
1210 } else {
1211 if (x < AIPTEK_TILT_MIN || x > AIPTEK_TILT_MAX)
1212 return -EINVAL;
1213
1214 aiptek->newSetting.xTilt = x;
1215 }
1216
1217 return count;
1218}
1219
1220static DEVICE_ATTR(xtilt,
1221 S_IRUGO | S_IWUSR, show_tabletXtilt, store_tabletXtilt);
1222
1223/***********************************************************************
1224 * support routines for the 'ytilt' file. Note that this file
1225 * both displays current setting and allows reprogramming.
1226 */
1227static ssize_t show_tabletYtilt(struct device *dev, struct device_attribute *attr, char *buf)
1228{
1229 struct aiptek *aiptek = dev_get_drvdata(dev);
1230
1231 if (aiptek->curSetting.yTilt == AIPTEK_TILT_DISABLE) {
1232 return snprintf(buf, PAGE_SIZE, "disable\n");
1233 } else {
1234 return snprintf(buf, PAGE_SIZE, "%d\n",
1235 aiptek->curSetting.yTilt);
1236 }
1237}
1238
1239static ssize_t
1240store_tabletYtilt(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1241{
1242 struct aiptek *aiptek = dev_get_drvdata(dev);
1243 int y;
1244
1245 if (kstrtoint(buf, 10, &y)) {
1246 size_t len = buf[count - 1] == '\n' ? count - 1 : count;
1247
1248 if (strncmp(buf, "disable", len))
1249 return -EINVAL;
1250
1251 aiptek->newSetting.yTilt = AIPTEK_TILT_DISABLE;
1252 } else {
1253 if (y < AIPTEK_TILT_MIN || y > AIPTEK_TILT_MAX)
1254 return -EINVAL;
1255
1256 aiptek->newSetting.yTilt = y;
1257 }
1258
1259 return count;
1260}
1261
1262static DEVICE_ATTR(ytilt,
1263 S_IRUGO | S_IWUSR, show_tabletYtilt, store_tabletYtilt);
1264
1265/***********************************************************************
1266 * support routines for the 'jitter' file. Note that this file
1267 * both displays current setting and allows reprogramming.
1268 */
1269static ssize_t show_tabletJitterDelay(struct device *dev, struct device_attribute *attr, char *buf)
1270{
1271 struct aiptek *aiptek = dev_get_drvdata(dev);
1272
1273 return snprintf(buf, PAGE_SIZE, "%d\n", aiptek->curSetting.jitterDelay);
1274}
1275
1276static ssize_t
1277store_tabletJitterDelay(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1278{
1279 struct aiptek *aiptek = dev_get_drvdata(dev);
1280 int err, j;
1281
1282 err = kstrtoint(buf, 10, &j);
1283 if (err)
1284 return err;
1285
1286 aiptek->newSetting.jitterDelay = j;
1287 return count;
1288}
1289
1290static DEVICE_ATTR(jitter,
1291 S_IRUGO | S_IWUSR,
1292 show_tabletJitterDelay, store_tabletJitterDelay);
1293
1294/***********************************************************************
1295 * support routines for the 'delay' file. Note that this file
1296 * both displays current setting and allows reprogramming.
1297 */
1298static ssize_t show_tabletProgrammableDelay(struct device *dev, struct device_attribute *attr, char *buf)
1299{
1300 struct aiptek *aiptek = dev_get_drvdata(dev);
1301
1302 return snprintf(buf, PAGE_SIZE, "%d\n",
1303 aiptek->curSetting.programmableDelay);
1304}
1305
1306static ssize_t
1307store_tabletProgrammableDelay(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1308{
1309 struct aiptek *aiptek = dev_get_drvdata(dev);
1310 int err, d;
1311
1312 err = kstrtoint(buf, 10, &d);
1313 if (err)
1314 return err;
1315
1316 aiptek->newSetting.programmableDelay = d;
1317 return count;
1318}
1319
1320static DEVICE_ATTR(delay,
1321 S_IRUGO | S_IWUSR,
1322 show_tabletProgrammableDelay, store_tabletProgrammableDelay);
1323
1324/***********************************************************************
1325 * support routines for the 'event_count' file. Note that this file
1326 * only displays current setting.
1327 */
1328static ssize_t show_tabletEventsReceived(struct device *dev, struct device_attribute *attr, char *buf)
1329{
1330 struct aiptek *aiptek = dev_get_drvdata(dev);
1331
1332 return snprintf(buf, PAGE_SIZE, "%ld\n", aiptek->eventCount);
1333}
1334
1335static DEVICE_ATTR(event_count, S_IRUGO, show_tabletEventsReceived, NULL);
1336
1337/***********************************************************************
1338 * support routines for the 'diagnostic' file. Note that this file
1339 * only displays current setting.
1340 */
1341static ssize_t show_tabletDiagnosticMessage(struct device *dev, struct device_attribute *attr, char *buf)
1342{
1343 struct aiptek *aiptek = dev_get_drvdata(dev);
1344 char *retMsg;
1345
1346 switch (aiptek->diagnostic) {
1347 case AIPTEK_DIAGNOSTIC_NA:
1348 retMsg = "no errors\n";
1349 break;
1350
1351 case AIPTEK_DIAGNOSTIC_SENDING_RELATIVE_IN_ABSOLUTE:
1352 retMsg = "Error: receiving relative reports\n";
1353 break;
1354
1355 case AIPTEK_DIAGNOSTIC_SENDING_ABSOLUTE_IN_RELATIVE:
1356 retMsg = "Error: receiving absolute reports\n";
1357 break;
1358
1359 case AIPTEK_DIAGNOSTIC_TOOL_DISALLOWED:
1360 if (aiptek->curSetting.pointerMode ==
1361 AIPTEK_POINTER_ONLY_MOUSE_MODE) {
1362 retMsg = "Error: receiving stylus reports\n";
1363 } else {
1364 retMsg = "Error: receiving mouse reports\n";
1365 }
1366 break;
1367
1368 default:
1369 return 0;
1370 }
1371 return snprintf(buf, PAGE_SIZE, retMsg);
1372}
1373
1374static DEVICE_ATTR(diagnostic, S_IRUGO, show_tabletDiagnosticMessage, NULL);
1375
1376/***********************************************************************
1377 * support routines for the 'stylus_upper' file. Note that this file
1378 * both displays current setting and allows for setting changing.
1379 */
1380
1381static struct aiptek_map stylus_button_map[] = {
1382 { "upper", AIPTEK_STYLUS_UPPER_BUTTON },
1383 { "lower", AIPTEK_STYLUS_LOWER_BUTTON },
1384 { NULL, AIPTEK_INVALID_VALUE }
1385};
1386
1387static ssize_t show_tabletStylusUpper(struct device *dev, struct device_attribute *attr, char *buf)
1388{
1389 struct aiptek *aiptek = dev_get_drvdata(dev);
1390
1391 return snprintf(buf, PAGE_SIZE, "%s\n",
1392 map_val_to_str(stylus_button_map,
1393 aiptek->curSetting.stylusButtonUpper));
1394}
1395
1396static ssize_t
1397store_tabletStylusUpper(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1398{
1399 struct aiptek *aiptek = dev_get_drvdata(dev);
1400 int new_button = map_str_to_val(stylus_button_map, buf, count);
1401
1402 if (new_button == AIPTEK_INVALID_VALUE)
1403 return -EINVAL;
1404
1405 aiptek->newSetting.stylusButtonUpper = new_button;
1406 return count;
1407}
1408
1409static DEVICE_ATTR(stylus_upper,
1410 S_IRUGO | S_IWUSR,
1411 show_tabletStylusUpper, store_tabletStylusUpper);
1412
1413/***********************************************************************
1414 * support routines for the 'stylus_lower' file. Note that this file
1415 * both displays current setting and allows for setting changing.
1416 */
1417
1418static ssize_t show_tabletStylusLower(struct device *dev, struct device_attribute *attr, char *buf)
1419{
1420 struct aiptek *aiptek = dev_get_drvdata(dev);
1421
1422 return snprintf(buf, PAGE_SIZE, "%s\n",
1423 map_val_to_str(stylus_button_map,
1424 aiptek->curSetting.stylusButtonLower));
1425}
1426
1427static ssize_t
1428store_tabletStylusLower(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1429{
1430 struct aiptek *aiptek = dev_get_drvdata(dev);
1431 int new_button = map_str_to_val(stylus_button_map, buf, count);
1432
1433 if (new_button == AIPTEK_INVALID_VALUE)
1434 return -EINVAL;
1435
1436 aiptek->newSetting.stylusButtonLower = new_button;
1437 return count;
1438}
1439
1440static DEVICE_ATTR(stylus_lower,
1441 S_IRUGO | S_IWUSR,
1442 show_tabletStylusLower, store_tabletStylusLower);
1443
1444/***********************************************************************
1445 * support routines for the 'mouse_left' file. Note that this file
1446 * both displays current setting and allows for setting changing.
1447 */
1448
1449static struct aiptek_map mouse_button_map[] = {
1450 { "left", AIPTEK_MOUSE_LEFT_BUTTON },
1451 { "middle", AIPTEK_MOUSE_MIDDLE_BUTTON },
1452 { "right", AIPTEK_MOUSE_RIGHT_BUTTON },
1453 { NULL, AIPTEK_INVALID_VALUE }
1454};
1455
1456static ssize_t show_tabletMouseLeft(struct device *dev, struct device_attribute *attr, char *buf)
1457{
1458 struct aiptek *aiptek = dev_get_drvdata(dev);
1459
1460 return snprintf(buf, PAGE_SIZE, "%s\n",
1461 map_val_to_str(mouse_button_map,
1462 aiptek->curSetting.mouseButtonLeft));
1463}
1464
1465static ssize_t
1466store_tabletMouseLeft(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1467{
1468 struct aiptek *aiptek = dev_get_drvdata(dev);
1469 int new_button = map_str_to_val(mouse_button_map, buf, count);
1470
1471 if (new_button == AIPTEK_INVALID_VALUE)
1472 return -EINVAL;
1473
1474 aiptek->newSetting.mouseButtonLeft = new_button;
1475 return count;
1476}
1477
1478static DEVICE_ATTR(mouse_left,
1479 S_IRUGO | S_IWUSR,
1480 show_tabletMouseLeft, store_tabletMouseLeft);
1481
1482/***********************************************************************
1483 * support routines for the 'mouse_middle' file. Note that this file
1484 * both displays current setting and allows for setting changing.
1485 */
1486static ssize_t show_tabletMouseMiddle(struct device *dev, struct device_attribute *attr, char *buf)
1487{
1488 struct aiptek *aiptek = dev_get_drvdata(dev);
1489
1490 return snprintf(buf, PAGE_SIZE, "%s\n",
1491 map_val_to_str(mouse_button_map,
1492 aiptek->curSetting.mouseButtonMiddle));
1493}
1494
1495static ssize_t
1496store_tabletMouseMiddle(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1497{
1498 struct aiptek *aiptek = dev_get_drvdata(dev);
1499 int new_button = map_str_to_val(mouse_button_map, buf, count);
1500
1501 if (new_button == AIPTEK_INVALID_VALUE)
1502 return -EINVAL;
1503
1504 aiptek->newSetting.mouseButtonMiddle = new_button;
1505 return count;
1506}
1507
1508static DEVICE_ATTR(mouse_middle,
1509 S_IRUGO | S_IWUSR,
1510 show_tabletMouseMiddle, store_tabletMouseMiddle);
1511
1512/***********************************************************************
1513 * support routines for the 'mouse_right' file. Note that this file
1514 * both displays current setting and allows for setting changing.
1515 */
1516static ssize_t show_tabletMouseRight(struct device *dev, struct device_attribute *attr, char *buf)
1517{
1518 struct aiptek *aiptek = dev_get_drvdata(dev);
1519
1520 return snprintf(buf, PAGE_SIZE, "%s\n",
1521 map_val_to_str(mouse_button_map,
1522 aiptek->curSetting.mouseButtonRight));
1523}
1524
1525static ssize_t
1526store_tabletMouseRight(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1527{
1528 struct aiptek *aiptek = dev_get_drvdata(dev);
1529 int new_button = map_str_to_val(mouse_button_map, buf, count);
1530
1531 if (new_button == AIPTEK_INVALID_VALUE)
1532 return -EINVAL;
1533
1534 aiptek->newSetting.mouseButtonRight = new_button;
1535 return count;
1536}
1537
1538static DEVICE_ATTR(mouse_right,
1539 S_IRUGO | S_IWUSR,
1540 show_tabletMouseRight, store_tabletMouseRight);
1541
1542/***********************************************************************
1543 * support routines for the 'wheel' file. Note that this file
1544 * both displays current setting and allows for setting changing.
1545 */
1546static ssize_t show_tabletWheel(struct device *dev, struct device_attribute *attr, char *buf)
1547{
1548 struct aiptek *aiptek = dev_get_drvdata(dev);
1549
1550 if (aiptek->curSetting.wheel == AIPTEK_WHEEL_DISABLE) {
1551 return snprintf(buf, PAGE_SIZE, "disable\n");
1552 } else {
1553 return snprintf(buf, PAGE_SIZE, "%d\n",
1554 aiptek->curSetting.wheel);
1555 }
1556}
1557
1558static ssize_t
1559store_tabletWheel(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1560{
1561 struct aiptek *aiptek = dev_get_drvdata(dev);
1562 int err, w;
1563
1564 err = kstrtoint(buf, 10, &w);
1565 if (err)
1566 return err;
1567
1568 aiptek->newSetting.wheel = w;
1569 return count;
1570}
1571
1572static DEVICE_ATTR(wheel,
1573 S_IRUGO | S_IWUSR, show_tabletWheel, store_tabletWheel);
1574
1575/***********************************************************************
1576 * support routines for the 'execute' file. Note that this file
1577 * both displays current setting and allows for setting changing.
1578 */
1579static ssize_t show_tabletExecute(struct device *dev, struct device_attribute *attr, char *buf)
1580{
1581 /* There is nothing useful to display, so a one-line manual
1582 * is in order...
1583 */
1584 return snprintf(buf, PAGE_SIZE,
1585 "Write anything to this file to program your tablet.\n");
1586}
1587
1588static ssize_t
1589store_tabletExecute(struct device *dev, struct device_attribute *attr, const char *buf, size_t count)
1590{
1591 struct aiptek *aiptek = dev_get_drvdata(dev);
1592
1593 /* We do not care what you write to this file. Merely the action
1594 * of writing to this file triggers a tablet reprogramming.
1595 */
1596 memcpy(&aiptek->curSetting, &aiptek->newSetting,
1597 sizeof(struct aiptek_settings));
1598
1599 if (aiptek_program_tablet(aiptek) < 0)
1600 return -EIO;
1601
1602 return count;
1603}
1604
1605static DEVICE_ATTR(execute,
1606 S_IRUGO | S_IWUSR, show_tabletExecute, store_tabletExecute);
1607
1608/***********************************************************************
1609 * support routines for the 'odm_code' file. Note that this file
1610 * only displays current setting.
1611 */
1612static ssize_t show_tabletODMCode(struct device *dev, struct device_attribute *attr, char *buf)
1613{
1614 struct aiptek *aiptek = dev_get_drvdata(dev);
1615
1616 return snprintf(buf, PAGE_SIZE, "0x%04x\n", aiptek->features.odmCode);
1617}
1618
1619static DEVICE_ATTR(odm_code, S_IRUGO, show_tabletODMCode, NULL);
1620
1621/***********************************************************************
1622 * support routines for the 'model_code' file. Note that this file
1623 * only displays current setting.
1624 */
1625static ssize_t show_tabletModelCode(struct device *dev, struct device_attribute *attr, char *buf)
1626{
1627 struct aiptek *aiptek = dev_get_drvdata(dev);
1628
1629 return snprintf(buf, PAGE_SIZE, "0x%04x\n", aiptek->features.modelCode);
1630}
1631
1632static DEVICE_ATTR(model_code, S_IRUGO, show_tabletModelCode, NULL);
1633
1634/***********************************************************************
1635 * support routines for the 'firmware_code' file. Note that this file
1636 * only displays current setting.
1637 */
1638static ssize_t show_firmwareCode(struct device *dev, struct device_attribute *attr, char *buf)
1639{
1640 struct aiptek *aiptek = dev_get_drvdata(dev);
1641
1642 return snprintf(buf, PAGE_SIZE, "%04x\n",
1643 aiptek->features.firmwareCode);
1644}
1645
1646static DEVICE_ATTR(firmware_code, S_IRUGO, show_firmwareCode, NULL);
1647
1648static struct attribute *aiptek_attributes[] = {
1649 &dev_attr_size.attr,
1650 &dev_attr_pointer_mode.attr,
1651 &dev_attr_coordinate_mode.attr,
1652 &dev_attr_tool_mode.attr,
1653 &dev_attr_xtilt.attr,
1654 &dev_attr_ytilt.attr,
1655 &dev_attr_jitter.attr,
1656 &dev_attr_delay.attr,
1657 &dev_attr_event_count.attr,
1658 &dev_attr_diagnostic.attr,
1659 &dev_attr_odm_code.attr,
1660 &dev_attr_model_code.attr,
1661 &dev_attr_firmware_code.attr,
1662 &dev_attr_stylus_lower.attr,
1663 &dev_attr_stylus_upper.attr,
1664 &dev_attr_mouse_left.attr,
1665 &dev_attr_mouse_middle.attr,
1666 &dev_attr_mouse_right.attr,
1667 &dev_attr_wheel.attr,
1668 &dev_attr_execute.attr,
1669 NULL
1670};
1671
1672static const struct attribute_group aiptek_attribute_group = {
1673 .attrs = aiptek_attributes,
1674};
1675
1676/***********************************************************************
1677 * This routine is called when a tablet has been identified. It basically
1678 * sets up the tablet and the driver's internal structures.
1679 */
1680static int
1681aiptek_probe(struct usb_interface *intf, const struct usb_device_id *id)
1682{
1683 struct usb_device *usbdev = interface_to_usbdev(intf);
1684 struct usb_endpoint_descriptor *endpoint;
1685 struct aiptek *aiptek;
1686 struct input_dev *inputdev;
1687 int i;
1688 int speeds[] = { 0,
1689 AIPTEK_PROGRAMMABLE_DELAY_50,
1690 AIPTEK_PROGRAMMABLE_DELAY_400,
1691 AIPTEK_PROGRAMMABLE_DELAY_25,
1692 AIPTEK_PROGRAMMABLE_DELAY_100,
1693 AIPTEK_PROGRAMMABLE_DELAY_200,
1694 AIPTEK_PROGRAMMABLE_DELAY_300
1695 };
1696 int err = -ENOMEM;
1697
1698 /* programmableDelay is where the command-line specified
1699 * delay is kept. We make it the first element of speeds[],
1700 * so therefore, your override speed is tried first, then the
1701 * remainder. Note that the default value of 400ms will be tried
1702 * if you do not specify any command line parameter.
1703 */
1704 speeds[0] = programmableDelay;
1705
1706 aiptek = kzalloc(sizeof(struct aiptek), GFP_KERNEL);
1707 inputdev = input_allocate_device();
1708 if (!aiptek || !inputdev) {
1709 dev_warn(&intf->dev,
1710 "cannot allocate memory or input device\n");
1711 goto fail1;
1712 }
1713
1714 aiptek->data = usb_alloc_coherent(usbdev, AIPTEK_PACKET_LENGTH,
1715 GFP_ATOMIC, &aiptek->data_dma);
1716 if (!aiptek->data) {
1717 dev_warn(&intf->dev, "cannot allocate usb buffer\n");
1718 goto fail1;
1719 }
1720
1721 aiptek->urb = usb_alloc_urb(0, GFP_KERNEL);
1722 if (!aiptek->urb) {
1723 dev_warn(&intf->dev, "cannot allocate urb\n");
1724 goto fail2;
1725 }
1726
1727 aiptek->inputdev = inputdev;
1728 aiptek->intf = intf;
1729 aiptek->ifnum = intf->altsetting[0].desc.bInterfaceNumber;
1730 aiptek->inDelay = 0;
1731 aiptek->endDelay = 0;
1732 aiptek->previousJitterable = 0;
1733 aiptek->lastMacro = -1;
1734
1735 /* Set up the curSettings struct. Said struct contains the current
1736 * programmable parameters. The newSetting struct contains changes
1737 * the user makes to the settings via the sysfs interface. Those
1738 * changes are not "committed" to curSettings until the user
1739 * writes to the sysfs/.../execute file.
1740 */
1741 aiptek->curSetting.pointerMode = AIPTEK_POINTER_EITHER_MODE;
1742 aiptek->curSetting.coordinateMode = AIPTEK_COORDINATE_ABSOLUTE_MODE;
1743 aiptek->curSetting.toolMode = AIPTEK_TOOL_BUTTON_PEN_MODE;
1744 aiptek->curSetting.xTilt = AIPTEK_TILT_DISABLE;
1745 aiptek->curSetting.yTilt = AIPTEK_TILT_DISABLE;
1746 aiptek->curSetting.mouseButtonLeft = AIPTEK_MOUSE_LEFT_BUTTON;
1747 aiptek->curSetting.mouseButtonMiddle = AIPTEK_MOUSE_MIDDLE_BUTTON;
1748 aiptek->curSetting.mouseButtonRight = AIPTEK_MOUSE_RIGHT_BUTTON;
1749 aiptek->curSetting.stylusButtonUpper = AIPTEK_STYLUS_UPPER_BUTTON;
1750 aiptek->curSetting.stylusButtonLower = AIPTEK_STYLUS_LOWER_BUTTON;
1751 aiptek->curSetting.jitterDelay = jitterDelay;
1752 aiptek->curSetting.programmableDelay = programmableDelay;
1753
1754 /* Both structs should have equivalent settings
1755 */
1756 aiptek->newSetting = aiptek->curSetting;
1757
1758 /* Determine the usb devices' physical path.
1759 * Asketh not why we always pretend we're using "../input0",
1760 * but I suspect this will have to be refactored one
1761 * day if a single USB device can be a keyboard & a mouse
1762 * & a tablet, and the inputX number actually will tell
1763 * us something...
1764 */
1765 usb_make_path(usbdev, aiptek->features.usbPath,
1766 sizeof(aiptek->features.usbPath));
1767 strlcat(aiptek->features.usbPath, "/input0",
1768 sizeof(aiptek->features.usbPath));
1769
1770 /* Set up client data, pointers to open and close routines
1771 * for the input device.
1772 */
1773 inputdev->name = "Aiptek";
1774 inputdev->phys = aiptek->features.usbPath;
1775 usb_to_input_id(usbdev, &inputdev->id);
1776 inputdev->dev.parent = &intf->dev;
1777
1778 input_set_drvdata(inputdev, aiptek);
1779
1780 inputdev->open = aiptek_open;
1781 inputdev->close = aiptek_close;
1782
1783 /* Now program the capacities of the tablet, in terms of being
1784 * an input device.
1785 */
1786 for (i = 0; i < ARRAY_SIZE(eventTypes); ++i)
1787 __set_bit(eventTypes[i], inputdev->evbit);
1788
1789 for (i = 0; i < ARRAY_SIZE(absEvents); ++i)
1790 __set_bit(absEvents[i], inputdev->absbit);
1791
1792 for (i = 0; i < ARRAY_SIZE(relEvents); ++i)
1793 __set_bit(relEvents[i], inputdev->relbit);
1794
1795 __set_bit(MSC_SERIAL, inputdev->mscbit);
1796
1797 /* Set up key and button codes */
1798 for (i = 0; i < ARRAY_SIZE(buttonEvents); ++i)
1799 __set_bit(buttonEvents[i], inputdev->keybit);
1800
1801 for (i = 0; i < ARRAY_SIZE(macroKeyEvents); ++i)
1802 __set_bit(macroKeyEvents[i], inputdev->keybit);
1803
1804 /*
1805 * Program the input device coordinate capacities. We do not yet
1806 * know what maximum X, Y, and Z values are, so we're putting fake
1807 * values in. Later, we'll ask the tablet to put in the correct
1808 * values.
1809 */
1810 input_set_abs_params(inputdev, ABS_X, 0, 2999, 0, 0);
1811 input_set_abs_params(inputdev, ABS_Y, 0, 2249, 0, 0);
1812 input_set_abs_params(inputdev, ABS_PRESSURE, 0, 511, 0, 0);
1813 input_set_abs_params(inputdev, ABS_TILT_X, AIPTEK_TILT_MIN, AIPTEK_TILT_MAX, 0, 0);
1814 input_set_abs_params(inputdev, ABS_TILT_Y, AIPTEK_TILT_MIN, AIPTEK_TILT_MAX, 0, 0);
1815 input_set_abs_params(inputdev, ABS_WHEEL, AIPTEK_WHEEL_MIN, AIPTEK_WHEEL_MAX - 1, 0, 0);
1816
1817 /* Verify that a device really has an endpoint */
1818 if (intf->altsetting[0].desc.bNumEndpoints < 1) {
1819 dev_err(&intf->dev,
1820 "interface has %d endpoints, but must have minimum 1\n",
1821 intf->altsetting[0].desc.bNumEndpoints);
1822 err = -EINVAL;
1823 goto fail3;
1824 }
1825 endpoint = &intf->altsetting[0].endpoint[0].desc;
1826
1827 /* Go set up our URB, which is called when the tablet receives
1828 * input.
1829 */
1830 usb_fill_int_urb(aiptek->urb,
1831 usbdev,
1832 usb_rcvintpipe(usbdev,
1833 endpoint->bEndpointAddress),
1834 aiptek->data, 8, aiptek_irq, aiptek,
1835 endpoint->bInterval);
1836
1837 aiptek->urb->transfer_dma = aiptek->data_dma;
1838 aiptek->urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
1839
1840 /* Program the tablet. This sets the tablet up in the mode
1841 * specified in newSetting, and also queries the tablet's
1842 * physical capacities.
1843 *
1844 * Sanity check: if a tablet doesn't like the slow programmatic
1845 * delay, we often get sizes of 0x0. Let's use that as an indicator
1846 * to try faster delays, up to 25 ms. If that logic fails, well, you'll
1847 * have to explain to us how your tablet thinks it's 0x0, and yet that's
1848 * not an error :-)
1849 */
1850
1851 for (i = 0; i < ARRAY_SIZE(speeds); ++i) {
1852 aiptek->curSetting.programmableDelay = speeds[i];
1853 (void)aiptek_program_tablet(aiptek);
1854 if (input_abs_get_max(aiptek->inputdev, ABS_X) > 0) {
1855 dev_info(&intf->dev,
1856 "Aiptek using %d ms programming speed\n",
1857 aiptek->curSetting.programmableDelay);
1858 break;
1859 }
1860 }
1861
1862 /* Murphy says that some day someone will have a tablet that fails the
1863 above test. That's you, Frederic Rodrigo */
1864 if (i == ARRAY_SIZE(speeds)) {
1865 dev_info(&intf->dev,
1866 "Aiptek tried all speeds, no sane response\n");
1867 err = -EINVAL;
1868 goto fail3;
1869 }
1870
1871 /* Associate this driver's struct with the usb interface.
1872 */
1873 usb_set_intfdata(intf, aiptek);
1874
1875 /* Set up the sysfs files
1876 */
1877 err = sysfs_create_group(&intf->dev.kobj, &aiptek_attribute_group);
1878 if (err) {
1879 dev_warn(&intf->dev, "cannot create sysfs group err: %d\n",
1880 err);
1881 goto fail3;
1882 }
1883
1884 /* Register the tablet as an Input Device
1885 */
1886 err = input_register_device(aiptek->inputdev);
1887 if (err) {
1888 dev_warn(&intf->dev,
1889 "input_register_device returned err: %d\n", err);
1890 goto fail4;
1891 }
1892 return 0;
1893
1894 fail4: sysfs_remove_group(&intf->dev.kobj, &aiptek_attribute_group);
1895 fail3: usb_free_urb(aiptek->urb);
1896 fail2: usb_free_coherent(usbdev, AIPTEK_PACKET_LENGTH, aiptek->data,
1897 aiptek->data_dma);
1898 fail1: usb_set_intfdata(intf, NULL);
1899 input_free_device(inputdev);
1900 kfree(aiptek);
1901 return err;
1902}
1903
1904/***********************************************************************
1905 * Deal with tablet disconnecting from the system.
1906 */
1907static void aiptek_disconnect(struct usb_interface *intf)
1908{
1909 struct aiptek *aiptek = usb_get_intfdata(intf);
1910
1911 /* Disassociate driver's struct with usb interface
1912 */
1913 usb_set_intfdata(intf, NULL);
1914 if (aiptek != NULL) {
1915 /* Free & unhook everything from the system.
1916 */
1917 usb_kill_urb(aiptek->urb);
1918 input_unregister_device(aiptek->inputdev);
1919 sysfs_remove_group(&intf->dev.kobj, &aiptek_attribute_group);
1920 usb_free_urb(aiptek->urb);
1921 usb_free_coherent(interface_to_usbdev(intf),
1922 AIPTEK_PACKET_LENGTH,
1923 aiptek->data, aiptek->data_dma);
1924 kfree(aiptek);
1925 }
1926}
1927
1928static struct usb_driver aiptek_driver = {
1929 .name = "aiptek",
1930 .probe = aiptek_probe,
1931 .disconnect = aiptek_disconnect,
1932 .id_table = aiptek_ids,
1933};
1934
1935module_usb_driver(aiptek_driver);
1936
1937MODULE_AUTHOR("Bryan W. Headley/Chris Atenasio/Cedric Brun/Rene van Paassen");
1938MODULE_DESCRIPTION("Aiptek HyperPen USB Tablet Driver");
1939MODULE_LICENSE("GPL");
1940
1941module_param(programmableDelay, int, 0);
1942MODULE_PARM_DESC(programmableDelay, "delay used during tablet programming");
1943module_param(jitterDelay, int, 0);
1944MODULE_PARM_DESC(jitterDelay, "stylus/mouse settlement delay");