1// SPDX-License-Identifier: GPL-2.0-or-later
 2/*
 3 * Copyright 2013 Eukréa Electromatique <eric@eukrea.com>
 4 * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
 
 
 
 
 
 
 
 
 
 5 */
 6
 7/*
 8 * Module contains : i.MX282 + 64MB DDR2 + NAND + Ethernet PHY + RTC
 9 */
10
11/dts-v1/;
12#include "imx28-eukrea-mbmx28lc.dtsi"
13
14/ {
15	model = "Eukrea Electromatique MBMX283LC";
16	compatible = "eukrea,mbmx283lc", "eukrea,mbmx28lc", "fsl,imx28";
17
18	memory@40000000 {
19		device_type = "memory";
20		reg = <0x40000000 0x04000000>;
21	};
22};
23
24&gpmi {
25	pinctrl-names = "default";
26	pinctrl-0 = <&gpmi_pins_a>;
27	status = "okay";
28};
29
30&i2c0 {
31	pinctrl-names = "default";
32	pinctrl-0 = <&i2c0_pins_a>;
33	status = "okay";
34
35	pcf8563: rtc@51 {
36		compatible = "nxp,pcf8563";
37		reg = <0x51>;
38	};
39};
40
41
42&mac0 {
43	phy-mode = "rmii";
44	pinctrl-names = "default";
45	pinctrl-0 = <&mac0_pins_a>;
46	phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
47	status = "okay";
48};
49
50&pinctrl{
51	pinctrl-names = "default";
52	pinctrl-0 = <&hog_pins_cpuimx283>;
53
54	hog_pins_cpuimx283: hog-cpuimx283@0 {
55		reg = <0>;
56		fsl,pinmux-ids = <
57			MX28_PAD_ENET0_RX_CLK__GPIO_4_13
58			MX28_PAD_ENET0_TX_CLK__GPIO_4_5
59		>;
60		fsl,drive-strength = <MXS_DRIVE_4mA>;
61		fsl,voltage = <MXS_VOLTAGE_HIGH>;
62		fsl,pull-up = <MXS_PULL_ENABLE>;
63	};
64};

 
 1/*
 2 * Copyright 2013 Eukréa Electromatique <eric@eukrea.com>
 3 * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
 4 *
 5 * This program is free software; you can redistribute it and/or
 6 * modify it under the terms of the GNU General Public License
 7 * as published by the Free Software Foundation; either version 2
 8 * of the License, or (at your option) any later version.
 9 * This program is distributed in the hope that it will be useful,
10 * but WITHOUT ANY WARRANTY; without even the implied warranty of
11 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
12 * GNU General Public License for more details.
13 */
14
15/*
16 * Module contains : i.MX282 + 64MB DDR2 + NAND + Ethernet PHY + RTC
17 */
18
19/dts-v1/;
20#include "imx28-eukrea-mbmx28lc.dtsi"
21
22/ {
23	model = "Eukrea Electromatique MBMX283LC";
24	compatible = "eukrea,mbmx283lc", "eukrea,mbmx28lc", "fsl,imx28";
25
26	memory {
 
27		reg = <0x40000000 0x04000000>;
28	};
29};
30
31&gpmi {
32	pinctrl-names = "default";
33	pinctrl-0 = <&gpmi_pins_a>;
34	status = "okay";
35};
36
37&i2c0 {
38	pinctrl-names = "default";
39	pinctrl-0 = <&i2c0_pins_a>;
40	status = "okay";
41
42	pcf8563: rtc@51 {
43		compatible = "nxp,pcf8563";
44		reg = <0x51>;
45	};
46};
47
48
49&mac0 {
50	phy-mode = "rmii";
51	pinctrl-names = "default";
52	pinctrl-0 = <&mac0_pins_a>;
53	phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
54	status = "okay";
55};
56
57&pinctrl{
58	pinctrl-names = "default";
59	pinctrl-0 = <&hog_pins_cpuimx283>;
60
61	hog_pins_cpuimx283: hog-cpuimx283@0 {
62		reg = <0>;
63		fsl,pinmux-ids = <
64			MX28_PAD_ENET0_RX_CLK__GPIO_4_13
65			MX28_PAD_ENET0_TX_CLK__GPIO_4_5
66		>;
67		fsl,drive-strength = <MXS_DRIVE_4mA>;
68		fsl,voltage = <MXS_VOLTAGE_HIGH>;
69		fsl,pull-up = <MXS_PULL_ENABLE>;
70	};
71};