Loading...
1// SPDX-License-Identifier: (GPL-2.0 OR MIT)
2/*
3 * Device Tree file for the Linksys WRT1900AC (Mamba).
4 *
5 * Note: this board is shipped with a new generation boot loader that
6 * remaps internal registers at 0xf1000000. Therefore, if earlyprintk
7 * is used, the CONFIG_DEBUG_MVEBU_UART0_ALTERNATE option should be
8 * used.
9 *
10 * Copyright (C) 2014 Imre Kaloz <kaloz@openwrt.org>
11 *
12 * Based on armada-xp-axpwifiap.dts:
13 *
14 * Copyright (C) 2013 Marvell
15 *
16 * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
17 */
18
19/dts-v1/;
20#include <dt-bindings/gpio/gpio.h>
21#include <dt-bindings/input/input.h>
22#include "armada-xp-mv78230.dtsi"
23
24/ {
25 model = "Linksys WRT1900AC";
26 compatible = "linksys,mamba", "marvell,armadaxp-mv78230",
27 "marvell,armadaxp", "marvell,armada-370-xp";
28
29 chosen {
30 bootargs = "console=ttyS0,115200";
31 stdout-path = &uart0;
32 };
33
34 memory@0 {
35 device_type = "memory";
36 reg = <0x00000000 0x00000000 0x00000000 0x10000000>; /* 256MB */
37 };
38
39 soc {
40 ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
41 MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
42 MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000
43 MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000
44 MBUS_ID(0x0c, 0x04) 0 0 0xf1200000 0x100000>;
45
46 internal-regs {
47
48 rtc@10300 {
49 /* No crystal connected to the internal RTC */
50 status = "disabled";
51 };
52
53 /* J10: VCC, NC, RX, NC, TX, GND */
54 serial@12000 {
55 status = "okay";
56 };
57
58 sata@a0000 {
59 nr-ports = <1>;
60 status = "okay";
61 };
62
63 ethernet@70000 {
64 pinctrl-0 = <&ge0_rgmii_pins>;
65 pinctrl-names = "default";
66 status = "okay";
67 phy-mode = "rgmii-id";
68 buffer-manager = <&bm>;
69 bm,pool-long = <0>;
70 bm,pool-short = <1>;
71 fixed-link {
72 speed = <1000>;
73 full-duplex;
74 };
75 };
76
77 ethernet@74000 {
78 pinctrl-0 = <&ge1_rgmii_pins>;
79 pinctrl-names = "default";
80 status = "okay";
81 phy-mode = "rgmii-id";
82 buffer-manager = <&bm>;
83 bm,pool-long = <2>;
84 bm,pool-short = <3>;
85 fixed-link {
86 speed = <1000>;
87 full-duplex;
88 };
89 };
90
91 /* USB part of the eSATA/USB 2.0 port */
92 usb@50000 {
93 status = "okay";
94 };
95
96 i2c@11000 {
97 status = "okay";
98 clock-frequency = <100000>;
99
100 tmp421@4c {
101 compatible = "ti,tmp421";
102 reg = <0x4c>;
103 };
104
105 tlc59116@68 {
106 #address-cells = <1>;
107 #size-cells = <0>;
108 #gpio-cells = <2>;
109 compatible = "ti,tlc59116";
110 reg = <0x68>;
111
112 wan_amber@0 {
113 label = "mamba:amber:wan";
114 reg = <0x0>;
115 };
116
117 wan_white@1 {
118 label = "mamba:white:wan";
119 reg = <0x1>;
120 };
121
122 wlan_2g@2 {
123 label = "mamba:white:wlan_2g";
124 reg = <0x2>;
125 };
126
127 wlan_5g@3 {
128 label = "mamba:white:wlan_5g";
129 reg = <0x3>;
130 };
131
132 esata@4 {
133 label = "mamba:white:esata";
134 reg = <0x4>;
135 linux,default-trigger = "disk-activity";
136 };
137
138 usb2@5 {
139 label = "mamba:white:usb2";
140 reg = <0x5>;
141 };
142
143 usb3_1@6 {
144 label = "mamba:white:usb3_1";
145 reg = <0x6>;
146 };
147
148 usb3_2@7 {
149 label = "mamba:white:usb3_2";
150 reg = <0x7>;
151 };
152
153 wps_white@8 {
154 label = "mamba:white:wps";
155 reg = <0x8>;
156 };
157
158 wps_amber@9 {
159 label = "mamba:amber:wps";
160 reg = <0x9>;
161 };
162 };
163 };
164
165 bm@c8000 {
166 status = "okay";
167 };
168 };
169
170 bm-bppi {
171 status = "okay";
172 };
173 };
174
175 gpio-keys {
176 compatible = "gpio-keys";
177 pinctrl-0 = <&keys_pin>;
178 pinctrl-names = "default";
179
180 button-wps {
181 label = "WPS";
182 linux,code = <KEY_WPS_BUTTON>;
183 gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
184 };
185
186 button-reset {
187 label = "Factory Reset Button";
188 linux,code = <KEY_RESTART>;
189 gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
190 };
191 };
192
193 gpio-leds {
194 compatible = "gpio-leds";
195 pinctrl-0 = <&power_led_pin>;
196 pinctrl-names = "default";
197
198 led-power {
199 label = "mamba:white:power";
200 gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
201 default-state = "on";
202 };
203 };
204
205 pwm_fan {
206 /* SUNON HA4010V4-0000-C99 */
207
208 compatible = "pwm-fan";
209 pwms = <&gpio0 24 4000>;
210 };
211};
212
213&pciec {
214 status = "okay";
215
216 /* Etron EJ168 USB 3.0 controller */
217 pcie@1,0 {
218 /* Port 0, Lane 0 */
219 status = "okay";
220 };
221
222 /* First mini-PCIe port */
223 pcie@2,0 {
224 /* Port 0, Lane 1 */
225 status = "okay";
226 };
227
228 /* Second mini-PCIe port */
229 pcie@3,0 {
230 /* Port 0, Lane 3 */
231 status = "okay";
232 };
233};
234
235&pinctrl {
236
237 keys_pin: keys-pin {
238 marvell,pins = "mpp32", "mpp33";
239 marvell,function = "gpio";
240 };
241
242 power_led_pin: power-led-pin {
243 marvell,pins = "mpp40";
244 marvell,function = "gpio";
245 };
246
247 gpio_fan_pin: gpio-fan-pin {
248 marvell,pins = "mpp24";
249 marvell,function = "gpio";
250 };
251};
252
253&spi0 {
254 status = "okay";
255
256 flash@0 {
257 #address-cells = <1>;
258 #size-cells = <1>;
259 compatible = "everspin,mr25h256";
260 reg = <0>; /* Chip select 0 */
261 spi-max-frequency = <40000000>;
262 };
263};
264
265&mdio {
266 status = "okay";
267
268 switch@0 {
269 compatible = "marvell,mv88e6085";
270 #address-cells = <1>;
271 #size-cells = <0>;
272 reg = <0>;
273
274 ports {
275 #address-cells = <1>;
276 #size-cells = <0>;
277
278 port@0 {
279 reg = <0>;
280 label = "lan4";
281 };
282
283 port@1 {
284 reg = <1>;
285 label = "lan3";
286 };
287
288 port@2 {
289 reg = <2>;
290 label = "lan2";
291 };
292
293 port@3 {
294 reg = <3>;
295 label = "lan1";
296 };
297
298 port@4 {
299 reg = <4>;
300 label = "internet";
301 };
302
303 port@5 {
304 reg = <5>;
305 label = "cpu";
306 ethernet = <ð0>;
307 fixed-link {
308 speed = <1000>;
309 full-duplex;
310 };
311 };
312 };
313 };
314};
315
316&nand_controller {
317 status = "okay";
318
319 nand@0 {
320 reg = <0>;
321 label = "pxa3xx_nand-0";
322 nand-rb = <0>;
323 marvell,nand-keep-config;
324 nand-on-flash-bbt;
325 nand-ecc-strength = <4>;
326 nand-ecc-step-size = <512>;
327
328 partitions {
329 compatible = "fixed-partitions";
330 #address-cells = <1>;
331 #size-cells = <1>;
332
333 partition@0 {
334 label = "u-boot";
335 reg = <0x0000000 0x100000>; /* 1MB */
336 read-only;
337 };
338
339 partition@100000 {
340 label = "u_env";
341 reg = <0x100000 0x40000>; /* 256KB */
342 };
343
344 partition@140000 {
345 label = "s_env";
346 reg = <0x140000 0x40000>; /* 256KB */
347 };
348
349 partition@900000 {
350 label = "devinfo";
351 reg = <0x900000 0x100000>; /* 1MB */
352 read-only;
353 };
354
355 /* kernel1 overlaps with rootfs1 by design */
356 partition@a00000 {
357 label = "kernel1";
358 reg = <0xa00000 0x2800000>; /* 40MB */
359 };
360
361 partition@d00000 {
362 label = "rootfs1";
363 reg = <0xd00000 0x2500000>; /* 37MB */
364 };
365
366 /* kernel2 overlaps with rootfs2 by design */
367 partition@3200000 {
368 label = "kernel2";
369 reg = <0x3200000 0x2800000>; /* 40MB */
370 };
371
372 partition@3500000 {
373 label = "rootfs2";
374 reg = <0x3500000 0x2500000>; /* 37MB */
375 };
376
377 /*
378 * 38MB, last MB is for the BBT, not writable
379 */
380 partition@5a00000 {
381 label = "syscfg";
382 reg = <0x5a00000 0x2600000>;
383 };
384
385 /*
386 * Unused area between "s_env" and "devinfo".
387 * Moved here because otherwise the renumbered
388 * partitions would break the bootloader
389 * supplied bootargs
390 */
391 partition@180000 {
392 label = "unused_area";
393 reg = <0x180000 0x780000>; /* 7.5MB */
394 };
395 };
396 };
397};
1/*
2 * Device Tree file for the Linksys WRT1900AC (Mamba).
3 *
4 * Note: this board is shipped with a new generation boot loader that
5 * remaps internal registers at 0xf1000000. Therefore, if earlyprintk
6 * is used, the CONFIG_DEBUG_MVEBU_UART0_ALTERNATE option should be
7 * used.
8 *
9 * Copyright (C) 2014 Imre Kaloz <kaloz@openwrt.org>
10 *
11 * Based on armada-xp-axpwifiap.dts:
12 *
13 * Copyright (C) 2013 Marvell
14 *
15 * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
16 *
17 * This file is dual-licensed: you can use it either under the terms
18 * of the GPL or the X11 license, at your option. Note that this dual
19 * licensing only applies to this file, and not this project as a
20 * whole.
21 *
22 * a) This file is licensed under the terms of the GNU General Public
23 * License version 2. This program is licensed "as is" without
24 * any warranty of any kind, whether express or implied.
25 *
26 * Or, alternatively,
27 *
28 * b) Permission is hereby granted, free of charge, to any person
29 * obtaining a copy of this software and associated documentation
30 * files (the "Software"), to deal in the Software without
31 * restriction, including without limitation the rights to use,
32 * copy, modify, merge, publish, distribute, sublicense, and/or
33 * sell copies of the Software, and to permit persons to whom the
34 * Software is furnished to do so, subject to the following
35 * conditions:
36 *
37 * The above copyright notice and this permission notice shall be
38 * included in all copies or substantial portions of the Software.
39 *
40 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
41 * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
42 * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
43 * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
44 * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
45 * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
46 * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
47 * OTHER DEALINGS IN THE SOFTWARE.
48 */
49
50/dts-v1/;
51#include <dt-bindings/gpio/gpio.h>
52#include <dt-bindings/input/input.h>
53#include "armada-xp-mv78230.dtsi"
54
55/ {
56 model = "Linksys WRT1900AC";
57 compatible = "linksys,mamba", "marvell,armadaxp-mv78230",
58 "marvell,armadaxp", "marvell,armada-370-xp";
59
60 chosen {
61 bootargs = "console=ttyS0,115200";
62 stdout-path = &uart0;
63 };
64
65 memory@0 {
66 device_type = "memory";
67 reg = <0x00000000 0x00000000 0x00000000 0x10000000>; /* 256MB */
68 };
69
70 soc {
71 ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
72 MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
73 MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000
74 MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000>;
75
76 internal-regs {
77
78 rtc@10300 {
79 /* No crystal connected to the internal RTC */
80 status = "disabled";
81 };
82
83 /* J10: VCC, NC, RX, NC, TX, GND */
84 serial@12000 {
85 status = "okay";
86 };
87
88 sata@a0000 {
89 nr-ports = <1>;
90 status = "okay";
91 };
92
93 ethernet@70000 {
94 pinctrl-0 = <&ge0_rgmii_pins>;
95 pinctrl-names = "default";
96 status = "okay";
97 phy-mode = "rgmii-id";
98 fixed-link {
99 speed = <1000>;
100 full-duplex;
101 };
102 };
103
104 ethernet@74000 {
105 pinctrl-0 = <&ge1_rgmii_pins>;
106 pinctrl-names = "default";
107 status = "okay";
108 phy-mode = "rgmii-id";
109 fixed-link {
110 speed = <1000>;
111 full-duplex;
112 };
113 };
114
115 /* USB part of the eSATA/USB 2.0 port */
116 usb@50000 {
117 status = "okay";
118 };
119
120 i2c@11000 {
121 status = "okay";
122 clock-frequency = <100000>;
123
124 tmp421@4c {
125 compatible = "ti,tmp421";
126 reg = <0x4c>;
127 };
128
129 tlc59116@68 {
130 #address-cells = <1>;
131 #size-cells = <0>;
132 #gpio-cells = <2>;
133 compatible = "ti,tlc59116";
134 reg = <0x68>;
135
136 wan_amber@0 {
137 label = "mamba:amber:wan";
138 reg = <0x0>;
139 };
140
141 wan_white@1 {
142 label = "mamba:white:wan";
143 reg = <0x1>;
144 };
145
146 wlan_2g@2 {
147 label = "mamba:white:wlan_2g";
148 reg = <0x2>;
149 };
150
151 wlan_5g@3 {
152 label = "mamba:white:wlan_5g";
153 reg = <0x3>;
154 };
155
156 esata@4 {
157 label = "mamba:white:esata";
158 reg = <0x4>;
159 };
160
161 usb2@5 {
162 label = "mamba:white:usb2";
163 reg = <0x5>;
164 };
165
166 usb3_1@6 {
167 label = "mamba:white:usb3_1";
168 reg = <0x6>;
169 };
170
171 usb3_2@7 {
172 label = "mamba:white:usb3_2";
173 reg = <0x7>;
174 };
175
176 wps_white@8 {
177 label = "mamba:white:wps";
178 reg = <0x8>;
179 };
180
181 wps_amber@9 {
182 label = "mamba:amber:wps";
183 reg = <0x9>;
184 };
185 };
186 };
187
188 nand@d0000 {
189 status = "okay";
190 num-cs = <1>;
191 marvell,nand-keep-config;
192 marvell,nand-enable-arbiter;
193 nand-on-flash-bbt;
194 nand-ecc-strength = <4>;
195 nand-ecc-step-size = <512>;
196
197 partition@0 {
198 label = "u-boot";
199 reg = <0x0000000 0x100000>; /* 1MB */
200 read-only;
201 };
202
203 partition@100000 {
204 label = "u_env";
205 reg = <0x100000 0x40000>; /* 256KB */
206 };
207
208 partition@140000 {
209 label = "s_env";
210 reg = <0x140000 0x40000>; /* 256KB */
211 };
212
213 partition@900000 {
214 label = "devinfo";
215 reg = <0x900000 0x100000>; /* 1MB */
216 read-only;
217 };
218
219 /* kernel1 overlaps with rootfs1 by design */
220 partition@a00000 {
221 label = "kernel1";
222 reg = <0xa00000 0x2800000>; /* 40MB */
223 };
224
225 partition@d00000 {
226 label = "rootfs1";
227 reg = <0xd00000 0x2500000>; /* 37MB */
228 };
229
230 /* kernel2 overlaps with rootfs2 by design */
231 partition@3200000 {
232 label = "kernel2";
233 reg = <0x3200000 0x2800000>; /* 40MB */
234 };
235
236 partition@3500000 {
237 label = "rootfs2";
238 reg = <0x3500000 0x2500000>; /* 37MB */
239 };
240
241 /*
242 * 38MB, last MB is for the BBT, not writable
243 */
244 partition@5a00000 {
245 label = "syscfg";
246 reg = <0x5a00000 0x2600000>;
247 };
248
249 /*
250 * Unused area between "s_env" and "devinfo".
251 * Moved here because otherwise the renumbered
252 * partitions would break the bootloader
253 * supplied bootargs
254 */
255 partition@180000 {
256 label = "unused_area";
257 reg = <0x180000 0x780000>; /* 7.5MB */
258 };
259 };
260 };
261 };
262
263 gpio_keys {
264 compatible = "gpio-keys";
265 #address-cells = <1>;
266 #size-cells = <0>;
267 pinctrl-0 = <&keys_pin>;
268 pinctrl-names = "default";
269
270 wps {
271 label = "WPS";
272 linux,code = <KEY_WPS_BUTTON>;
273 gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
274 };
275
276 reset {
277 label = "Factory Reset Button";
278 linux,code = <KEY_RESTART>;
279 gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
280 };
281 };
282
283 gpio-leds {
284 compatible = "gpio-leds";
285 pinctrl-0 = <&power_led_pin>;
286 pinctrl-names = "default";
287
288 power {
289 label = "mamba:white:power";
290 gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
291 default-state = "on";
292 };
293 };
294
295 gpio_fan {
296 /* SUNON HA4010V4-0000-C99 */
297 compatible = "gpio-fan";
298 gpios = <&gpio0 24 0>;
299
300 gpio-fan,speed-map = <0 0
301 4500 1>;
302 };
303
304 dsa {
305 compatible = "marvell,dsa";
306 #address-cells = <2>;
307 #size-cells = <0>;
308
309 dsa,ethernet = <ð0>;
310 dsa,mii-bus = <&mdio>;
311
312 switch@0 {
313 #address-cells = <1>;
314 #size-cells = <0>;
315 reg = <0x0 0>; /* MDIO address 0, switch 0 in tree */
316
317 port@0 {
318 reg = <0>;
319 label = "lan4";
320 };
321
322 port@1 {
323 reg = <1>;
324 label = "lan3";
325 };
326
327 port@2 {
328 reg = <2>;
329 label = "lan2";
330 };
331
332 port@3 {
333 reg = <3>;
334 label = "lan1";
335 };
336
337 port@4 {
338 reg = <4>;
339 label = "internet";
340 };
341
342 port@5 {
343 reg = <5>;
344 label = "cpu";
345 };
346 };
347 };
348};
349
350&pciec {
351 status = "okay";
352
353 /* Etron EJ168 USB 3.0 controller */
354 pcie@1,0 {
355 /* Port 0, Lane 0 */
356 status = "okay";
357 };
358
359 /* First mini-PCIe port */
360 pcie@2,0 {
361 /* Port 0, Lane 1 */
362 status = "okay";
363 };
364
365 /* Second mini-PCIe port */
366 pcie@3,0 {
367 /* Port 0, Lane 3 */
368 status = "okay";
369 };
370};
371
372&pinctrl {
373
374 keys_pin: keys-pin {
375 marvell,pins = "mpp32", "mpp33";
376 marvell,function = "gpio";
377 };
378
379 power_led_pin: power-led-pin {
380 marvell,pins = "mpp40";
381 marvell,function = "gpio";
382 };
383
384 gpio_fan_pin: gpio-fan-pin {
385 marvell,pins = "mpp24";
386 marvell,function = "gpio";
387 };
388};
389
390&spi0 {
391 status = "okay";
392
393 spi-flash@0 {
394 #address-cells = <1>;
395 #size-cells = <1>;
396 compatible = "everspin,mr25h256";
397 reg = <0>; /* Chip select 0 */
398 spi-max-frequency = <40000000>;
399 };
400};