Loading...
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * Driver for Atmel AT91 Serial ports
4 * Copyright (C) 2003 Rick Bronson
5 *
6 * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd.
7 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
8 *
9 * DMA support added by Chip Coldwell.
10 */
11#include <linux/circ_buf.h>
12#include <linux/tty.h>
13#include <linux/ioport.h>
14#include <linux/slab.h>
15#include <linux/init.h>
16#include <linux/serial.h>
17#include <linux/clk.h>
18#include <linux/clk-provider.h>
19#include <linux/console.h>
20#include <linux/sysrq.h>
21#include <linux/tty_flip.h>
22#include <linux/platform_device.h>
23#include <linux/of.h>
24#include <linux/of_device.h>
25#include <linux/dma-mapping.h>
26#include <linux/dmaengine.h>
27#include <linux/atmel_pdc.h>
28#include <linux/uaccess.h>
29#include <linux/platform_data/atmel.h>
30#include <linux/timer.h>
31#include <linux/err.h>
32#include <linux/irq.h>
33#include <linux/suspend.h>
34#include <linux/mm.h>
35#include <linux/io.h>
36
37#include <asm/div64.h>
38#include <asm/ioctls.h>
39
40#define PDC_BUFFER_SIZE 512
41/* Revisit: We should calculate this based on the actual port settings */
42#define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */
43
44/* The minium number of data FIFOs should be able to contain */
45#define ATMEL_MIN_FIFO_SIZE 8
46/*
47 * These two offsets are substracted from the RX FIFO size to define the RTS
48 * high and low thresholds
49 */
50#define ATMEL_RTS_HIGH_OFFSET 16
51#define ATMEL_RTS_LOW_OFFSET 20
52
53#include <linux/serial_core.h>
54
55#include "serial_mctrl_gpio.h"
56#include "atmel_serial.h"
57
58static void atmel_start_rx(struct uart_port *port);
59static void atmel_stop_rx(struct uart_port *port);
60
61#ifdef CONFIG_SERIAL_ATMEL_TTYAT
62
63/* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we
64 * should coexist with the 8250 driver, such as if we have an external 16C550
65 * UART. */
66#define SERIAL_ATMEL_MAJOR 204
67#define MINOR_START 154
68#define ATMEL_DEVICENAME "ttyAT"
69
70#else
71
72/* Use device name ttyS, major 4, minor 64-68. This is the usual serial port
73 * name, but it is legally reserved for the 8250 driver. */
74#define SERIAL_ATMEL_MAJOR TTY_MAJOR
75#define MINOR_START 64
76#define ATMEL_DEVICENAME "ttyS"
77
78#endif
79
80#define ATMEL_ISR_PASS_LIMIT 256
81
82struct atmel_dma_buffer {
83 unsigned char *buf;
84 dma_addr_t dma_addr;
85 unsigned int dma_size;
86 unsigned int ofs;
87};
88
89struct atmel_uart_char {
90 u16 status;
91 u16 ch;
92};
93
94/*
95 * Be careful, the real size of the ring buffer is
96 * sizeof(atmel_uart_char) * ATMEL_SERIAL_RINGSIZE. It means that ring buffer
97 * can contain up to 1024 characters in PIO mode and up to 4096 characters in
98 * DMA mode.
99 */
100#define ATMEL_SERIAL_RINGSIZE 1024
101
102/*
103 * at91: 6 USARTs and one DBGU port (SAM9260)
104 * samx7: 3 USARTs and 5 UARTs
105 */
106#define ATMEL_MAX_UART 8
107
108/*
109 * We wrap our port structure around the generic uart_port.
110 */
111struct atmel_uart_port {
112 struct uart_port uart; /* uart */
113 struct clk *clk; /* uart clock */
114 struct clk *gclk; /* uart generic clock */
115 int may_wakeup; /* cached value of device_may_wakeup for times we need to disable it */
116 u32 backup_imr; /* IMR saved during suspend */
117 int break_active; /* break being received */
118
119 bool use_dma_rx; /* enable DMA receiver */
120 bool use_pdc_rx; /* enable PDC receiver */
121 short pdc_rx_idx; /* current PDC RX buffer */
122 struct atmel_dma_buffer pdc_rx[2]; /* PDC receier */
123
124 bool use_dma_tx; /* enable DMA transmitter */
125 bool use_pdc_tx; /* enable PDC transmitter */
126 struct atmel_dma_buffer pdc_tx; /* PDC transmitter */
127
128 spinlock_t lock_tx; /* port lock */
129 spinlock_t lock_rx; /* port lock */
130 struct dma_chan *chan_tx;
131 struct dma_chan *chan_rx;
132 struct dma_async_tx_descriptor *desc_tx;
133 struct dma_async_tx_descriptor *desc_rx;
134 dma_cookie_t cookie_tx;
135 dma_cookie_t cookie_rx;
136 struct scatterlist sg_tx;
137 struct scatterlist sg_rx;
138 struct tasklet_struct tasklet_rx;
139 struct tasklet_struct tasklet_tx;
140 atomic_t tasklet_shutdown;
141 unsigned int irq_status_prev;
142 unsigned int tx_len;
143
144 struct circ_buf rx_ring;
145
146 struct mctrl_gpios *gpios;
147 u32 backup_mode; /* MR saved during iso7816 operations */
148 u32 backup_brgr; /* BRGR saved during iso7816 operations */
149 unsigned int tx_done_mask;
150 u32 fifo_size;
151 u32 rts_high;
152 u32 rts_low;
153 bool ms_irq_enabled;
154 u32 rtor; /* address of receiver timeout register if it exists */
155 bool is_usart;
156 bool has_frac_baudrate;
157 bool has_hw_timer;
158 struct timer_list uart_timer;
159
160 bool tx_stopped;
161 bool suspended;
162 unsigned int pending;
163 unsigned int pending_status;
164 spinlock_t lock_suspended;
165
166 bool hd_start_rx; /* can start RX during half-duplex operation */
167
168 /* ISO7816 */
169 unsigned int fidi_min;
170 unsigned int fidi_max;
171
172 struct {
173 u32 cr;
174 u32 mr;
175 u32 imr;
176 u32 brgr;
177 u32 rtor;
178 u32 ttgr;
179 u32 fmr;
180 u32 fimr;
181 } cache;
182
183 int (*prepare_rx)(struct uart_port *port);
184 int (*prepare_tx)(struct uart_port *port);
185 void (*schedule_rx)(struct uart_port *port);
186 void (*schedule_tx)(struct uart_port *port);
187 void (*release_rx)(struct uart_port *port);
188 void (*release_tx)(struct uart_port *port);
189};
190
191static struct atmel_uart_port atmel_ports[ATMEL_MAX_UART];
192static DECLARE_BITMAP(atmel_ports_in_use, ATMEL_MAX_UART);
193
194#if defined(CONFIG_OF)
195static const struct of_device_id atmel_serial_dt_ids[] = {
196 { .compatible = "atmel,at91rm9200-usart-serial" },
197 { /* sentinel */ }
198};
199#endif
200
201static inline struct atmel_uart_port *
202to_atmel_uart_port(struct uart_port *uart)
203{
204 return container_of(uart, struct atmel_uart_port, uart);
205}
206
207static inline u32 atmel_uart_readl(struct uart_port *port, u32 reg)
208{
209 return __raw_readl(port->membase + reg);
210}
211
212static inline void atmel_uart_writel(struct uart_port *port, u32 reg, u32 value)
213{
214 __raw_writel(value, port->membase + reg);
215}
216
217static inline u8 atmel_uart_read_char(struct uart_port *port)
218{
219 return __raw_readb(port->membase + ATMEL_US_RHR);
220}
221
222static inline void atmel_uart_write_char(struct uart_port *port, u8 value)
223{
224 __raw_writeb(value, port->membase + ATMEL_US_THR);
225}
226
227static inline int atmel_uart_is_half_duplex(struct uart_port *port)
228{
229 return ((port->rs485.flags & SER_RS485_ENABLED) &&
230 !(port->rs485.flags & SER_RS485_RX_DURING_TX)) ||
231 (port->iso7816.flags & SER_ISO7816_ENABLED);
232}
233
234static inline int atmel_error_rate(int desired_value, int actual_value)
235{
236 return 100 - (desired_value * 100) / actual_value;
237}
238
239#ifdef CONFIG_SERIAL_ATMEL_PDC
240static bool atmel_use_pdc_rx(struct uart_port *port)
241{
242 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
243
244 return atmel_port->use_pdc_rx;
245}
246
247static bool atmel_use_pdc_tx(struct uart_port *port)
248{
249 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
250
251 return atmel_port->use_pdc_tx;
252}
253#else
254static bool atmel_use_pdc_rx(struct uart_port *port)
255{
256 return false;
257}
258
259static bool atmel_use_pdc_tx(struct uart_port *port)
260{
261 return false;
262}
263#endif
264
265static bool atmel_use_dma_tx(struct uart_port *port)
266{
267 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
268
269 return atmel_port->use_dma_tx;
270}
271
272static bool atmel_use_dma_rx(struct uart_port *port)
273{
274 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
275
276 return atmel_port->use_dma_rx;
277}
278
279static bool atmel_use_fifo(struct uart_port *port)
280{
281 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
282
283 return atmel_port->fifo_size;
284}
285
286static void atmel_tasklet_schedule(struct atmel_uart_port *atmel_port,
287 struct tasklet_struct *t)
288{
289 if (!atomic_read(&atmel_port->tasklet_shutdown))
290 tasklet_schedule(t);
291}
292
293/* Enable or disable the rs485 support */
294static int atmel_config_rs485(struct uart_port *port, struct ktermios *termios,
295 struct serial_rs485 *rs485conf)
296{
297 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
298 unsigned int mode;
299
300 /* Disable interrupts */
301 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
302
303 mode = atmel_uart_readl(port, ATMEL_US_MR);
304
305 if (rs485conf->flags & SER_RS485_ENABLED) {
306 dev_dbg(port->dev, "Setting UART to RS485\n");
307 if (rs485conf->flags & SER_RS485_RX_DURING_TX)
308 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
309 else
310 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
311
312 atmel_uart_writel(port, ATMEL_US_TTGR,
313 rs485conf->delay_rts_after_send);
314 mode &= ~ATMEL_US_USMODE;
315 mode |= ATMEL_US_USMODE_RS485;
316 } else {
317 dev_dbg(port->dev, "Setting UART to RS232\n");
318 if (atmel_use_pdc_tx(port))
319 atmel_port->tx_done_mask = ATMEL_US_ENDTX |
320 ATMEL_US_TXBUFE;
321 else
322 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
323 }
324 atmel_uart_writel(port, ATMEL_US_MR, mode);
325
326 /* Enable interrupts */
327 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
328
329 return 0;
330}
331
332static unsigned int atmel_calc_cd(struct uart_port *port,
333 struct serial_iso7816 *iso7816conf)
334{
335 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
336 unsigned int cd;
337 u64 mck_rate;
338
339 mck_rate = (u64)clk_get_rate(atmel_port->clk);
340 do_div(mck_rate, iso7816conf->clk);
341 cd = mck_rate;
342 return cd;
343}
344
345static unsigned int atmel_calc_fidi(struct uart_port *port,
346 struct serial_iso7816 *iso7816conf)
347{
348 u64 fidi = 0;
349
350 if (iso7816conf->sc_fi && iso7816conf->sc_di) {
351 fidi = (u64)iso7816conf->sc_fi;
352 do_div(fidi, iso7816conf->sc_di);
353 }
354 return (u32)fidi;
355}
356
357/* Enable or disable the iso7816 support */
358/* Called with interrupts disabled */
359static int atmel_config_iso7816(struct uart_port *port,
360 struct serial_iso7816 *iso7816conf)
361{
362 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
363 unsigned int mode;
364 unsigned int cd, fidi;
365 int ret = 0;
366
367 /* Disable interrupts */
368 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
369
370 mode = atmel_uart_readl(port, ATMEL_US_MR);
371
372 if (iso7816conf->flags & SER_ISO7816_ENABLED) {
373 mode &= ~ATMEL_US_USMODE;
374
375 if (iso7816conf->tg > 255) {
376 dev_err(port->dev, "ISO7816: Timeguard exceeding 255\n");
377 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
378 ret = -EINVAL;
379 goto err_out;
380 }
381
382 if ((iso7816conf->flags & SER_ISO7816_T_PARAM)
383 == SER_ISO7816_T(0)) {
384 mode |= ATMEL_US_USMODE_ISO7816_T0 | ATMEL_US_DSNACK;
385 } else if ((iso7816conf->flags & SER_ISO7816_T_PARAM)
386 == SER_ISO7816_T(1)) {
387 mode |= ATMEL_US_USMODE_ISO7816_T1 | ATMEL_US_INACK;
388 } else {
389 dev_err(port->dev, "ISO7816: Type not supported\n");
390 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
391 ret = -EINVAL;
392 goto err_out;
393 }
394
395 mode &= ~(ATMEL_US_USCLKS | ATMEL_US_NBSTOP | ATMEL_US_PAR);
396
397 /* select mck clock, and output */
398 mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO;
399 /* set parity for normal/inverse mode + max iterations */
400 mode |= ATMEL_US_PAR_EVEN | ATMEL_US_NBSTOP_1 | ATMEL_US_MAX_ITER(3);
401
402 cd = atmel_calc_cd(port, iso7816conf);
403 fidi = atmel_calc_fidi(port, iso7816conf);
404 if (fidi == 0) {
405 dev_warn(port->dev, "ISO7816 fidi = 0, Generator generates no signal\n");
406 } else if (fidi < atmel_port->fidi_min
407 || fidi > atmel_port->fidi_max) {
408 dev_err(port->dev, "ISO7816 fidi = %u, value not supported\n", fidi);
409 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
410 ret = -EINVAL;
411 goto err_out;
412 }
413
414 if (!(port->iso7816.flags & SER_ISO7816_ENABLED)) {
415 /* port not yet in iso7816 mode: store configuration */
416 atmel_port->backup_mode = atmel_uart_readl(port, ATMEL_US_MR);
417 atmel_port->backup_brgr = atmel_uart_readl(port, ATMEL_US_BRGR);
418 }
419
420 atmel_uart_writel(port, ATMEL_US_TTGR, iso7816conf->tg);
421 atmel_uart_writel(port, ATMEL_US_BRGR, cd);
422 atmel_uart_writel(port, ATMEL_US_FIDI, fidi);
423
424 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXEN);
425 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY | ATMEL_US_NACK | ATMEL_US_ITERATION;
426 } else {
427 dev_dbg(port->dev, "Setting UART back to RS232\n");
428 /* back to last RS232 settings */
429 mode = atmel_port->backup_mode;
430 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
431 atmel_uart_writel(port, ATMEL_US_TTGR, 0);
432 atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->backup_brgr);
433 atmel_uart_writel(port, ATMEL_US_FIDI, 0x174);
434
435 if (atmel_use_pdc_tx(port))
436 atmel_port->tx_done_mask = ATMEL_US_ENDTX |
437 ATMEL_US_TXBUFE;
438 else
439 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
440 }
441
442 port->iso7816 = *iso7816conf;
443
444 atmel_uart_writel(port, ATMEL_US_MR, mode);
445
446err_out:
447 /* Enable interrupts */
448 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
449
450 return ret;
451}
452
453/*
454 * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty.
455 */
456static u_int atmel_tx_empty(struct uart_port *port)
457{
458 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
459
460 if (atmel_port->tx_stopped)
461 return TIOCSER_TEMT;
462 return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ?
463 TIOCSER_TEMT :
464 0;
465}
466
467/*
468 * Set state of the modem control output lines
469 */
470static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
471{
472 unsigned int control = 0;
473 unsigned int mode = atmel_uart_readl(port, ATMEL_US_MR);
474 unsigned int rts_paused, rts_ready;
475 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
476
477 /* override mode to RS485 if needed, otherwise keep the current mode */
478 if (port->rs485.flags & SER_RS485_ENABLED) {
479 atmel_uart_writel(port, ATMEL_US_TTGR,
480 port->rs485.delay_rts_after_send);
481 mode &= ~ATMEL_US_USMODE;
482 mode |= ATMEL_US_USMODE_RS485;
483 }
484
485 /* set the RTS line state according to the mode */
486 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) {
487 /* force RTS line to high level */
488 rts_paused = ATMEL_US_RTSEN;
489
490 /* give the control of the RTS line back to the hardware */
491 rts_ready = ATMEL_US_RTSDIS;
492 } else {
493 /* force RTS line to high level */
494 rts_paused = ATMEL_US_RTSDIS;
495
496 /* force RTS line to low level */
497 rts_ready = ATMEL_US_RTSEN;
498 }
499
500 if (mctrl & TIOCM_RTS)
501 control |= rts_ready;
502 else
503 control |= rts_paused;
504
505 if (mctrl & TIOCM_DTR)
506 control |= ATMEL_US_DTREN;
507 else
508 control |= ATMEL_US_DTRDIS;
509
510 atmel_uart_writel(port, ATMEL_US_CR, control);
511
512 mctrl_gpio_set(atmel_port->gpios, mctrl);
513
514 /* Local loopback mode? */
515 mode &= ~ATMEL_US_CHMODE;
516 if (mctrl & TIOCM_LOOP)
517 mode |= ATMEL_US_CHMODE_LOC_LOOP;
518 else
519 mode |= ATMEL_US_CHMODE_NORMAL;
520
521 atmel_uart_writel(port, ATMEL_US_MR, mode);
522}
523
524/*
525 * Get state of the modem control input lines
526 */
527static u_int atmel_get_mctrl(struct uart_port *port)
528{
529 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
530 unsigned int ret = 0, status;
531
532 status = atmel_uart_readl(port, ATMEL_US_CSR);
533
534 /*
535 * The control signals are active low.
536 */
537 if (!(status & ATMEL_US_DCD))
538 ret |= TIOCM_CD;
539 if (!(status & ATMEL_US_CTS))
540 ret |= TIOCM_CTS;
541 if (!(status & ATMEL_US_DSR))
542 ret |= TIOCM_DSR;
543 if (!(status & ATMEL_US_RI))
544 ret |= TIOCM_RI;
545
546 return mctrl_gpio_get(atmel_port->gpios, &ret);
547}
548
549/*
550 * Stop transmitting.
551 */
552static void atmel_stop_tx(struct uart_port *port)
553{
554 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
555 bool is_pdc = atmel_use_pdc_tx(port);
556 bool is_dma = is_pdc || atmel_use_dma_tx(port);
557
558 if (is_pdc) {
559 /* disable PDC transmit */
560 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
561 }
562
563 if (is_dma) {
564 /*
565 * Disable the transmitter.
566 * This is mandatory when DMA is used, otherwise the DMA buffer
567 * is fully transmitted.
568 */
569 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS);
570 atmel_port->tx_stopped = true;
571 }
572
573 /* Disable interrupts */
574 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
575
576 if (atmel_uart_is_half_duplex(port))
577 if (!atomic_read(&atmel_port->tasklet_shutdown))
578 atmel_start_rx(port);
579}
580
581/*
582 * Start transmitting.
583 */
584static void atmel_start_tx(struct uart_port *port)
585{
586 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
587 bool is_pdc = atmel_use_pdc_tx(port);
588 bool is_dma = is_pdc || atmel_use_dma_tx(port);
589
590 if (is_pdc && (atmel_uart_readl(port, ATMEL_PDC_PTSR)
591 & ATMEL_PDC_TXTEN))
592 /* The transmitter is already running. Yes, we
593 really need this.*/
594 return;
595
596 if (is_dma && atmel_uart_is_half_duplex(port))
597 atmel_stop_rx(port);
598
599 if (is_pdc) {
600 /* re-enable PDC transmit */
601 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
602 }
603
604 /* Enable interrupts */
605 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
606
607 if (is_dma) {
608 /* re-enable the transmitter */
609 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
610 atmel_port->tx_stopped = false;
611 }
612}
613
614/*
615 * start receiving - port is in process of being opened.
616 */
617static void atmel_start_rx(struct uart_port *port)
618{
619 /* reset status and receiver */
620 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
621
622 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXEN);
623
624 if (atmel_use_pdc_rx(port)) {
625 /* enable PDC controller */
626 atmel_uart_writel(port, ATMEL_US_IER,
627 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
628 port->read_status_mask);
629 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
630 } else {
631 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY);
632 }
633}
634
635/*
636 * Stop receiving - port is in process of being closed.
637 */
638static void atmel_stop_rx(struct uart_port *port)
639{
640 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXDIS);
641
642 if (atmel_use_pdc_rx(port)) {
643 /* disable PDC receive */
644 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS);
645 atmel_uart_writel(port, ATMEL_US_IDR,
646 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
647 port->read_status_mask);
648 } else {
649 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXRDY);
650 }
651}
652
653/*
654 * Enable modem status interrupts
655 */
656static void atmel_enable_ms(struct uart_port *port)
657{
658 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
659 uint32_t ier = 0;
660
661 /*
662 * Interrupt should not be enabled twice
663 */
664 if (atmel_port->ms_irq_enabled)
665 return;
666
667 atmel_port->ms_irq_enabled = true;
668
669 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
670 ier |= ATMEL_US_CTSIC;
671
672 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR))
673 ier |= ATMEL_US_DSRIC;
674
675 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI))
676 ier |= ATMEL_US_RIIC;
677
678 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD))
679 ier |= ATMEL_US_DCDIC;
680
681 atmel_uart_writel(port, ATMEL_US_IER, ier);
682
683 mctrl_gpio_enable_ms(atmel_port->gpios);
684}
685
686/*
687 * Disable modem status interrupts
688 */
689static void atmel_disable_ms(struct uart_port *port)
690{
691 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
692 uint32_t idr = 0;
693
694 /*
695 * Interrupt should not be disabled twice
696 */
697 if (!atmel_port->ms_irq_enabled)
698 return;
699
700 atmel_port->ms_irq_enabled = false;
701
702 mctrl_gpio_disable_ms(atmel_port->gpios);
703
704 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
705 idr |= ATMEL_US_CTSIC;
706
707 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR))
708 idr |= ATMEL_US_DSRIC;
709
710 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI))
711 idr |= ATMEL_US_RIIC;
712
713 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD))
714 idr |= ATMEL_US_DCDIC;
715
716 atmel_uart_writel(port, ATMEL_US_IDR, idr);
717}
718
719/*
720 * Control the transmission of a break signal
721 */
722static void atmel_break_ctl(struct uart_port *port, int break_state)
723{
724 if (break_state != 0)
725 /* start break */
726 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTBRK);
727 else
728 /* stop break */
729 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STPBRK);
730}
731
732/*
733 * Stores the incoming character in the ring buffer
734 */
735static void
736atmel_buffer_rx_char(struct uart_port *port, unsigned int status,
737 unsigned int ch)
738{
739 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
740 struct circ_buf *ring = &atmel_port->rx_ring;
741 struct atmel_uart_char *c;
742
743 if (!CIRC_SPACE(ring->head, ring->tail, ATMEL_SERIAL_RINGSIZE))
744 /* Buffer overflow, ignore char */
745 return;
746
747 c = &((struct atmel_uart_char *)ring->buf)[ring->head];
748 c->status = status;
749 c->ch = ch;
750
751 /* Make sure the character is stored before we update head. */
752 smp_wmb();
753
754 ring->head = (ring->head + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
755}
756
757/*
758 * Deal with parity, framing and overrun errors.
759 */
760static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status)
761{
762 /* clear error */
763 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
764
765 if (status & ATMEL_US_RXBRK) {
766 /* ignore side-effect */
767 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
768 port->icount.brk++;
769 }
770 if (status & ATMEL_US_PARE)
771 port->icount.parity++;
772 if (status & ATMEL_US_FRAME)
773 port->icount.frame++;
774 if (status & ATMEL_US_OVRE)
775 port->icount.overrun++;
776}
777
778/*
779 * Characters received (called from interrupt handler)
780 */
781static void atmel_rx_chars(struct uart_port *port)
782{
783 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
784 unsigned int status, ch;
785
786 status = atmel_uart_readl(port, ATMEL_US_CSR);
787 while (status & ATMEL_US_RXRDY) {
788 ch = atmel_uart_read_char(port);
789
790 /*
791 * note that the error handling code is
792 * out of the main execution path
793 */
794 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
795 | ATMEL_US_OVRE | ATMEL_US_RXBRK)
796 || atmel_port->break_active)) {
797
798 /* clear error */
799 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
800
801 if (status & ATMEL_US_RXBRK
802 && !atmel_port->break_active) {
803 atmel_port->break_active = 1;
804 atmel_uart_writel(port, ATMEL_US_IER,
805 ATMEL_US_RXBRK);
806 } else {
807 /*
808 * This is either the end-of-break
809 * condition or we've received at
810 * least one character without RXBRK
811 * being set. In both cases, the next
812 * RXBRK will indicate start-of-break.
813 */
814 atmel_uart_writel(port, ATMEL_US_IDR,
815 ATMEL_US_RXBRK);
816 status &= ~ATMEL_US_RXBRK;
817 atmel_port->break_active = 0;
818 }
819 }
820
821 atmel_buffer_rx_char(port, status, ch);
822 status = atmel_uart_readl(port, ATMEL_US_CSR);
823 }
824
825 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx);
826}
827
828/*
829 * Transmit characters (called from tasklet with TXRDY interrupt
830 * disabled)
831 */
832static void atmel_tx_chars(struct uart_port *port)
833{
834 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
835 bool pending;
836 u8 ch;
837
838 pending = uart_port_tx(port, ch,
839 atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY,
840 atmel_uart_write_char(port, ch));
841 if (pending) {
842 /* we still have characters to transmit, so we should continue
843 * transmitting them when TX is ready, regardless of
844 * mode or duplexity
845 */
846 atmel_port->tx_done_mask |= ATMEL_US_TXRDY;
847
848 /* Enable interrupts */
849 atmel_uart_writel(port, ATMEL_US_IER,
850 atmel_port->tx_done_mask);
851 } else {
852 if (atmel_uart_is_half_duplex(port))
853 atmel_port->tx_done_mask &= ~ATMEL_US_TXRDY;
854 }
855}
856
857static void atmel_complete_tx_dma(void *arg)
858{
859 struct atmel_uart_port *atmel_port = arg;
860 struct uart_port *port = &atmel_port->uart;
861 struct circ_buf *xmit = &port->state->xmit;
862 struct dma_chan *chan = atmel_port->chan_tx;
863 unsigned long flags;
864
865 spin_lock_irqsave(&port->lock, flags);
866
867 if (chan)
868 dmaengine_terminate_all(chan);
869 uart_xmit_advance(port, atmel_port->tx_len);
870
871 spin_lock_irq(&atmel_port->lock_tx);
872 async_tx_ack(atmel_port->desc_tx);
873 atmel_port->cookie_tx = -EINVAL;
874 atmel_port->desc_tx = NULL;
875 spin_unlock_irq(&atmel_port->lock_tx);
876
877 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
878 uart_write_wakeup(port);
879
880 /*
881 * xmit is a circular buffer so, if we have just send data from
882 * xmit->tail to the end of xmit->buf, now we have to transmit the
883 * remaining data from the beginning of xmit->buf to xmit->head.
884 */
885 if (!uart_circ_empty(xmit))
886 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
887 else if (atmel_uart_is_half_duplex(port)) {
888 /*
889 * DMA done, re-enable TXEMPTY and signal that we can stop
890 * TX and start RX for RS485
891 */
892 atmel_port->hd_start_rx = true;
893 atmel_uart_writel(port, ATMEL_US_IER,
894 atmel_port->tx_done_mask);
895 }
896
897 spin_unlock_irqrestore(&port->lock, flags);
898}
899
900static void atmel_release_tx_dma(struct uart_port *port)
901{
902 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
903 struct dma_chan *chan = atmel_port->chan_tx;
904
905 if (chan) {
906 dmaengine_terminate_all(chan);
907 dma_release_channel(chan);
908 dma_unmap_sg(port->dev, &atmel_port->sg_tx, 1,
909 DMA_TO_DEVICE);
910 }
911
912 atmel_port->desc_tx = NULL;
913 atmel_port->chan_tx = NULL;
914 atmel_port->cookie_tx = -EINVAL;
915}
916
917/*
918 * Called from tasklet with TXRDY interrupt is disabled.
919 */
920static void atmel_tx_dma(struct uart_port *port)
921{
922 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
923 struct circ_buf *xmit = &port->state->xmit;
924 struct dma_chan *chan = atmel_port->chan_tx;
925 struct dma_async_tx_descriptor *desc;
926 struct scatterlist sgl[2], *sg, *sg_tx = &atmel_port->sg_tx;
927 unsigned int tx_len, part1_len, part2_len, sg_len;
928 dma_addr_t phys_addr;
929
930 /* Make sure we have an idle channel */
931 if (atmel_port->desc_tx != NULL)
932 return;
933
934 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
935 /*
936 * DMA is idle now.
937 * Port xmit buffer is already mapped,
938 * and it is one page... Just adjust
939 * offsets and lengths. Since it is a circular buffer,
940 * we have to transmit till the end, and then the rest.
941 * Take the port lock to get a
942 * consistent xmit buffer state.
943 */
944 tx_len = CIRC_CNT_TO_END(xmit->head,
945 xmit->tail,
946 UART_XMIT_SIZE);
947
948 if (atmel_port->fifo_size) {
949 /* multi data mode */
950 part1_len = (tx_len & ~0x3); /* DWORD access */
951 part2_len = (tx_len & 0x3); /* BYTE access */
952 } else {
953 /* single data (legacy) mode */
954 part1_len = 0;
955 part2_len = tx_len; /* BYTE access only */
956 }
957
958 sg_init_table(sgl, 2);
959 sg_len = 0;
960 phys_addr = sg_dma_address(sg_tx) + xmit->tail;
961 if (part1_len) {
962 sg = &sgl[sg_len++];
963 sg_dma_address(sg) = phys_addr;
964 sg_dma_len(sg) = part1_len;
965
966 phys_addr += part1_len;
967 }
968
969 if (part2_len) {
970 sg = &sgl[sg_len++];
971 sg_dma_address(sg) = phys_addr;
972 sg_dma_len(sg) = part2_len;
973 }
974
975 /*
976 * save tx_len so atmel_complete_tx_dma() will increase
977 * xmit->tail correctly
978 */
979 atmel_port->tx_len = tx_len;
980
981 desc = dmaengine_prep_slave_sg(chan,
982 sgl,
983 sg_len,
984 DMA_MEM_TO_DEV,
985 DMA_PREP_INTERRUPT |
986 DMA_CTRL_ACK);
987 if (!desc) {
988 dev_err(port->dev, "Failed to send via dma!\n");
989 return;
990 }
991
992 dma_sync_sg_for_device(port->dev, sg_tx, 1, DMA_TO_DEVICE);
993
994 atmel_port->desc_tx = desc;
995 desc->callback = atmel_complete_tx_dma;
996 desc->callback_param = atmel_port;
997 atmel_port->cookie_tx = dmaengine_submit(desc);
998 if (dma_submit_error(atmel_port->cookie_tx)) {
999 dev_err(port->dev, "dma_submit_error %d\n",
1000 atmel_port->cookie_tx);
1001 return;
1002 }
1003
1004 dma_async_issue_pending(chan);
1005 }
1006
1007 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1008 uart_write_wakeup(port);
1009}
1010
1011static int atmel_prepare_tx_dma(struct uart_port *port)
1012{
1013 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1014 struct device *mfd_dev = port->dev->parent;
1015 dma_cap_mask_t mask;
1016 struct dma_slave_config config;
1017 int ret, nent;
1018
1019 dma_cap_zero(mask);
1020 dma_cap_set(DMA_SLAVE, mask);
1021
1022 atmel_port->chan_tx = dma_request_slave_channel(mfd_dev, "tx");
1023 if (atmel_port->chan_tx == NULL)
1024 goto chan_err;
1025 dev_info(port->dev, "using %s for tx DMA transfers\n",
1026 dma_chan_name(atmel_port->chan_tx));
1027
1028 spin_lock_init(&atmel_port->lock_tx);
1029 sg_init_table(&atmel_port->sg_tx, 1);
1030 /* UART circular tx buffer is an aligned page. */
1031 BUG_ON(!PAGE_ALIGNED(port->state->xmit.buf));
1032 sg_set_page(&atmel_port->sg_tx,
1033 virt_to_page(port->state->xmit.buf),
1034 UART_XMIT_SIZE,
1035 offset_in_page(port->state->xmit.buf));
1036 nent = dma_map_sg(port->dev,
1037 &atmel_port->sg_tx,
1038 1,
1039 DMA_TO_DEVICE);
1040
1041 if (!nent) {
1042 dev_dbg(port->dev, "need to release resource of dma\n");
1043 goto chan_err;
1044 } else {
1045 dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n", __func__,
1046 sg_dma_len(&atmel_port->sg_tx),
1047 port->state->xmit.buf,
1048 &sg_dma_address(&atmel_port->sg_tx));
1049 }
1050
1051 /* Configure the slave DMA */
1052 memset(&config, 0, sizeof(config));
1053 config.direction = DMA_MEM_TO_DEV;
1054 config.dst_addr_width = (atmel_port->fifo_size) ?
1055 DMA_SLAVE_BUSWIDTH_4_BYTES :
1056 DMA_SLAVE_BUSWIDTH_1_BYTE;
1057 config.dst_addr = port->mapbase + ATMEL_US_THR;
1058 config.dst_maxburst = 1;
1059
1060 ret = dmaengine_slave_config(atmel_port->chan_tx,
1061 &config);
1062 if (ret) {
1063 dev_err(port->dev, "DMA tx slave configuration failed\n");
1064 goto chan_err;
1065 }
1066
1067 return 0;
1068
1069chan_err:
1070 dev_err(port->dev, "TX channel not available, switch to pio\n");
1071 atmel_port->use_dma_tx = false;
1072 if (atmel_port->chan_tx)
1073 atmel_release_tx_dma(port);
1074 return -EINVAL;
1075}
1076
1077static void atmel_complete_rx_dma(void *arg)
1078{
1079 struct uart_port *port = arg;
1080 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1081
1082 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx);
1083}
1084
1085static void atmel_release_rx_dma(struct uart_port *port)
1086{
1087 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1088 struct dma_chan *chan = atmel_port->chan_rx;
1089
1090 if (chan) {
1091 dmaengine_terminate_all(chan);
1092 dma_release_channel(chan);
1093 dma_unmap_sg(port->dev, &atmel_port->sg_rx, 1,
1094 DMA_FROM_DEVICE);
1095 }
1096
1097 atmel_port->desc_rx = NULL;
1098 atmel_port->chan_rx = NULL;
1099 atmel_port->cookie_rx = -EINVAL;
1100}
1101
1102static void atmel_rx_from_dma(struct uart_port *port)
1103{
1104 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1105 struct tty_port *tport = &port->state->port;
1106 struct circ_buf *ring = &atmel_port->rx_ring;
1107 struct dma_chan *chan = atmel_port->chan_rx;
1108 struct dma_tx_state state;
1109 enum dma_status dmastat;
1110 size_t count;
1111
1112
1113 /* Reset the UART timeout early so that we don't miss one */
1114 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1115 dmastat = dmaengine_tx_status(chan,
1116 atmel_port->cookie_rx,
1117 &state);
1118 /* Restart a new tasklet if DMA status is error */
1119 if (dmastat == DMA_ERROR) {
1120 dev_dbg(port->dev, "Get residue error, restart tasklet\n");
1121 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT);
1122 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx);
1123 return;
1124 }
1125
1126 /* CPU claims ownership of RX DMA buffer */
1127 dma_sync_sg_for_cpu(port->dev,
1128 &atmel_port->sg_rx,
1129 1,
1130 DMA_FROM_DEVICE);
1131
1132 /*
1133 * ring->head points to the end of data already written by the DMA.
1134 * ring->tail points to the beginning of data to be read by the
1135 * framework.
1136 * The current transfer size should not be larger than the dma buffer
1137 * length.
1138 */
1139 ring->head = sg_dma_len(&atmel_port->sg_rx) - state.residue;
1140 BUG_ON(ring->head > sg_dma_len(&atmel_port->sg_rx));
1141 /*
1142 * At this point ring->head may point to the first byte right after the
1143 * last byte of the dma buffer:
1144 * 0 <= ring->head <= sg_dma_len(&atmel_port->sg_rx)
1145 *
1146 * However ring->tail must always points inside the dma buffer:
1147 * 0 <= ring->tail <= sg_dma_len(&atmel_port->sg_rx) - 1
1148 *
1149 * Since we use a ring buffer, we have to handle the case
1150 * where head is lower than tail. In such a case, we first read from
1151 * tail to the end of the buffer then reset tail.
1152 */
1153 if (ring->head < ring->tail) {
1154 count = sg_dma_len(&atmel_port->sg_rx) - ring->tail;
1155
1156 tty_insert_flip_string(tport, ring->buf + ring->tail, count);
1157 ring->tail = 0;
1158 port->icount.rx += count;
1159 }
1160
1161 /* Finally we read data from tail to head */
1162 if (ring->tail < ring->head) {
1163 count = ring->head - ring->tail;
1164
1165 tty_insert_flip_string(tport, ring->buf + ring->tail, count);
1166 /* Wrap ring->head if needed */
1167 if (ring->head >= sg_dma_len(&atmel_port->sg_rx))
1168 ring->head = 0;
1169 ring->tail = ring->head;
1170 port->icount.rx += count;
1171 }
1172
1173 /* USART retreives ownership of RX DMA buffer */
1174 dma_sync_sg_for_device(port->dev,
1175 &atmel_port->sg_rx,
1176 1,
1177 DMA_FROM_DEVICE);
1178
1179 tty_flip_buffer_push(tport);
1180
1181 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT);
1182}
1183
1184static int atmel_prepare_rx_dma(struct uart_port *port)
1185{
1186 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1187 struct device *mfd_dev = port->dev->parent;
1188 struct dma_async_tx_descriptor *desc;
1189 dma_cap_mask_t mask;
1190 struct dma_slave_config config;
1191 struct circ_buf *ring;
1192 int ret, nent;
1193
1194 ring = &atmel_port->rx_ring;
1195
1196 dma_cap_zero(mask);
1197 dma_cap_set(DMA_CYCLIC, mask);
1198
1199 atmel_port->chan_rx = dma_request_slave_channel(mfd_dev, "rx");
1200 if (atmel_port->chan_rx == NULL)
1201 goto chan_err;
1202 dev_info(port->dev, "using %s for rx DMA transfers\n",
1203 dma_chan_name(atmel_port->chan_rx));
1204
1205 spin_lock_init(&atmel_port->lock_rx);
1206 sg_init_table(&atmel_port->sg_rx, 1);
1207 /* UART circular rx buffer is an aligned page. */
1208 BUG_ON(!PAGE_ALIGNED(ring->buf));
1209 sg_set_page(&atmel_port->sg_rx,
1210 virt_to_page(ring->buf),
1211 sizeof(struct atmel_uart_char) * ATMEL_SERIAL_RINGSIZE,
1212 offset_in_page(ring->buf));
1213 nent = dma_map_sg(port->dev,
1214 &atmel_port->sg_rx,
1215 1,
1216 DMA_FROM_DEVICE);
1217
1218 if (!nent) {
1219 dev_dbg(port->dev, "need to release resource of dma\n");
1220 goto chan_err;
1221 } else {
1222 dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n", __func__,
1223 sg_dma_len(&atmel_port->sg_rx),
1224 ring->buf,
1225 &sg_dma_address(&atmel_port->sg_rx));
1226 }
1227
1228 /* Configure the slave DMA */
1229 memset(&config, 0, sizeof(config));
1230 config.direction = DMA_DEV_TO_MEM;
1231 config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1232 config.src_addr = port->mapbase + ATMEL_US_RHR;
1233 config.src_maxburst = 1;
1234
1235 ret = dmaengine_slave_config(atmel_port->chan_rx,
1236 &config);
1237 if (ret) {
1238 dev_err(port->dev, "DMA rx slave configuration failed\n");
1239 goto chan_err;
1240 }
1241 /*
1242 * Prepare a cyclic dma transfer, assign 2 descriptors,
1243 * each one is half ring buffer size
1244 */
1245 desc = dmaengine_prep_dma_cyclic(atmel_port->chan_rx,
1246 sg_dma_address(&atmel_port->sg_rx),
1247 sg_dma_len(&atmel_port->sg_rx),
1248 sg_dma_len(&atmel_port->sg_rx)/2,
1249 DMA_DEV_TO_MEM,
1250 DMA_PREP_INTERRUPT);
1251 if (!desc) {
1252 dev_err(port->dev, "Preparing DMA cyclic failed\n");
1253 goto chan_err;
1254 }
1255 desc->callback = atmel_complete_rx_dma;
1256 desc->callback_param = port;
1257 atmel_port->desc_rx = desc;
1258 atmel_port->cookie_rx = dmaengine_submit(desc);
1259 if (dma_submit_error(atmel_port->cookie_rx)) {
1260 dev_err(port->dev, "dma_submit_error %d\n",
1261 atmel_port->cookie_rx);
1262 goto chan_err;
1263 }
1264
1265 dma_async_issue_pending(atmel_port->chan_rx);
1266
1267 return 0;
1268
1269chan_err:
1270 dev_err(port->dev, "RX channel not available, switch to pio\n");
1271 atmel_port->use_dma_rx = false;
1272 if (atmel_port->chan_rx)
1273 atmel_release_rx_dma(port);
1274 return -EINVAL;
1275}
1276
1277static void atmel_uart_timer_callback(struct timer_list *t)
1278{
1279 struct atmel_uart_port *atmel_port = from_timer(atmel_port, t,
1280 uart_timer);
1281 struct uart_port *port = &atmel_port->uart;
1282
1283 if (!atomic_read(&atmel_port->tasklet_shutdown)) {
1284 tasklet_schedule(&atmel_port->tasklet_rx);
1285 mod_timer(&atmel_port->uart_timer,
1286 jiffies + uart_poll_timeout(port));
1287 }
1288}
1289
1290/*
1291 * receive interrupt handler.
1292 */
1293static void
1294atmel_handle_receive(struct uart_port *port, unsigned int pending)
1295{
1296 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1297
1298 if (atmel_use_pdc_rx(port)) {
1299 /*
1300 * PDC receive. Just schedule the tasklet and let it
1301 * figure out the details.
1302 *
1303 * TODO: We're not handling error flags correctly at
1304 * the moment.
1305 */
1306 if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) {
1307 atmel_uart_writel(port, ATMEL_US_IDR,
1308 (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT));
1309 atmel_tasklet_schedule(atmel_port,
1310 &atmel_port->tasklet_rx);
1311 }
1312
1313 if (pending & (ATMEL_US_RXBRK | ATMEL_US_OVRE |
1314 ATMEL_US_FRAME | ATMEL_US_PARE))
1315 atmel_pdc_rxerr(port, pending);
1316 }
1317
1318 if (atmel_use_dma_rx(port)) {
1319 if (pending & ATMEL_US_TIMEOUT) {
1320 atmel_uart_writel(port, ATMEL_US_IDR,
1321 ATMEL_US_TIMEOUT);
1322 atmel_tasklet_schedule(atmel_port,
1323 &atmel_port->tasklet_rx);
1324 }
1325 }
1326
1327 /* Interrupt receive */
1328 if (pending & ATMEL_US_RXRDY)
1329 atmel_rx_chars(port);
1330 else if (pending & ATMEL_US_RXBRK) {
1331 /*
1332 * End of break detected. If it came along with a
1333 * character, atmel_rx_chars will handle it.
1334 */
1335 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
1336 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXBRK);
1337 atmel_port->break_active = 0;
1338 }
1339}
1340
1341/*
1342 * transmit interrupt handler. (Transmit is IRQF_NODELAY safe)
1343 */
1344static void
1345atmel_handle_transmit(struct uart_port *port, unsigned int pending)
1346{
1347 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1348
1349 if (pending & atmel_port->tx_done_mask) {
1350 atmel_uart_writel(port, ATMEL_US_IDR,
1351 atmel_port->tx_done_mask);
1352
1353 /* Start RX if flag was set and FIFO is empty */
1354 if (atmel_port->hd_start_rx) {
1355 if (!(atmel_uart_readl(port, ATMEL_US_CSR)
1356 & ATMEL_US_TXEMPTY))
1357 dev_warn(port->dev, "Should start RX, but TX fifo is not empty\n");
1358
1359 atmel_port->hd_start_rx = false;
1360 atmel_start_rx(port);
1361 }
1362
1363 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
1364 }
1365}
1366
1367/*
1368 * status flags interrupt handler.
1369 */
1370static void
1371atmel_handle_status(struct uart_port *port, unsigned int pending,
1372 unsigned int status)
1373{
1374 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1375 unsigned int status_change;
1376
1377 if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC
1378 | ATMEL_US_CTSIC)) {
1379 status_change = status ^ atmel_port->irq_status_prev;
1380 atmel_port->irq_status_prev = status;
1381
1382 if (status_change & (ATMEL_US_RI | ATMEL_US_DSR
1383 | ATMEL_US_DCD | ATMEL_US_CTS)) {
1384 /* TODO: All reads to CSR will clear these interrupts! */
1385 if (status_change & ATMEL_US_RI)
1386 port->icount.rng++;
1387 if (status_change & ATMEL_US_DSR)
1388 port->icount.dsr++;
1389 if (status_change & ATMEL_US_DCD)
1390 uart_handle_dcd_change(port, !(status & ATMEL_US_DCD));
1391 if (status_change & ATMEL_US_CTS)
1392 uart_handle_cts_change(port, !(status & ATMEL_US_CTS));
1393
1394 wake_up_interruptible(&port->state->port.delta_msr_wait);
1395 }
1396 }
1397
1398 if (pending & (ATMEL_US_NACK | ATMEL_US_ITERATION))
1399 dev_dbg(port->dev, "ISO7816 ERROR (0x%08x)\n", pending);
1400}
1401
1402/*
1403 * Interrupt handler
1404 */
1405static irqreturn_t atmel_interrupt(int irq, void *dev_id)
1406{
1407 struct uart_port *port = dev_id;
1408 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1409 unsigned int status, pending, mask, pass_counter = 0;
1410
1411 spin_lock(&atmel_port->lock_suspended);
1412
1413 do {
1414 status = atmel_uart_readl(port, ATMEL_US_CSR);
1415 mask = atmel_uart_readl(port, ATMEL_US_IMR);
1416 pending = status & mask;
1417 if (!pending)
1418 break;
1419
1420 if (atmel_port->suspended) {
1421 atmel_port->pending |= pending;
1422 atmel_port->pending_status = status;
1423 atmel_uart_writel(port, ATMEL_US_IDR, mask);
1424 pm_system_wakeup();
1425 break;
1426 }
1427
1428 atmel_handle_receive(port, pending);
1429 atmel_handle_status(port, pending, status);
1430 atmel_handle_transmit(port, pending);
1431 } while (pass_counter++ < ATMEL_ISR_PASS_LIMIT);
1432
1433 spin_unlock(&atmel_port->lock_suspended);
1434
1435 return pass_counter ? IRQ_HANDLED : IRQ_NONE;
1436}
1437
1438static void atmel_release_tx_pdc(struct uart_port *port)
1439{
1440 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1441 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1442
1443 dma_unmap_single(port->dev,
1444 pdc->dma_addr,
1445 pdc->dma_size,
1446 DMA_TO_DEVICE);
1447}
1448
1449/*
1450 * Called from tasklet with ENDTX and TXBUFE interrupts disabled.
1451 */
1452static void atmel_tx_pdc(struct uart_port *port)
1453{
1454 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1455 struct circ_buf *xmit = &port->state->xmit;
1456 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1457 int count;
1458
1459 /* nothing left to transmit? */
1460 if (atmel_uart_readl(port, ATMEL_PDC_TCR))
1461 return;
1462 uart_xmit_advance(port, pdc->ofs);
1463 pdc->ofs = 0;
1464
1465 /* more to transmit - setup next transfer */
1466
1467 /* disable PDC transmit */
1468 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
1469
1470 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
1471 dma_sync_single_for_device(port->dev,
1472 pdc->dma_addr,
1473 pdc->dma_size,
1474 DMA_TO_DEVICE);
1475
1476 count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
1477 pdc->ofs = count;
1478
1479 atmel_uart_writel(port, ATMEL_PDC_TPR,
1480 pdc->dma_addr + xmit->tail);
1481 atmel_uart_writel(port, ATMEL_PDC_TCR, count);
1482 /* re-enable PDC transmit */
1483 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
1484 /* Enable interrupts */
1485 atmel_uart_writel(port, ATMEL_US_IER,
1486 atmel_port->tx_done_mask);
1487 } else {
1488 if (atmel_uart_is_half_duplex(port)) {
1489 /* DMA done, stop TX, start RX for RS485 */
1490 atmel_start_rx(port);
1491 }
1492 }
1493
1494 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1495 uart_write_wakeup(port);
1496}
1497
1498static int atmel_prepare_tx_pdc(struct uart_port *port)
1499{
1500 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1501 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1502 struct circ_buf *xmit = &port->state->xmit;
1503
1504 pdc->buf = xmit->buf;
1505 pdc->dma_addr = dma_map_single(port->dev,
1506 pdc->buf,
1507 UART_XMIT_SIZE,
1508 DMA_TO_DEVICE);
1509 pdc->dma_size = UART_XMIT_SIZE;
1510 pdc->ofs = 0;
1511
1512 return 0;
1513}
1514
1515static void atmel_rx_from_ring(struct uart_port *port)
1516{
1517 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1518 struct circ_buf *ring = &atmel_port->rx_ring;
1519 unsigned int flg;
1520 unsigned int status;
1521
1522 while (ring->head != ring->tail) {
1523 struct atmel_uart_char c;
1524
1525 /* Make sure c is loaded after head. */
1526 smp_rmb();
1527
1528 c = ((struct atmel_uart_char *)ring->buf)[ring->tail];
1529
1530 ring->tail = (ring->tail + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
1531
1532 port->icount.rx++;
1533 status = c.status;
1534 flg = TTY_NORMAL;
1535
1536 /*
1537 * note that the error handling code is
1538 * out of the main execution path
1539 */
1540 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
1541 | ATMEL_US_OVRE | ATMEL_US_RXBRK))) {
1542 if (status & ATMEL_US_RXBRK) {
1543 /* ignore side-effect */
1544 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
1545
1546 port->icount.brk++;
1547 if (uart_handle_break(port))
1548 continue;
1549 }
1550 if (status & ATMEL_US_PARE)
1551 port->icount.parity++;
1552 if (status & ATMEL_US_FRAME)
1553 port->icount.frame++;
1554 if (status & ATMEL_US_OVRE)
1555 port->icount.overrun++;
1556
1557 status &= port->read_status_mask;
1558
1559 if (status & ATMEL_US_RXBRK)
1560 flg = TTY_BREAK;
1561 else if (status & ATMEL_US_PARE)
1562 flg = TTY_PARITY;
1563 else if (status & ATMEL_US_FRAME)
1564 flg = TTY_FRAME;
1565 }
1566
1567
1568 if (uart_handle_sysrq_char(port, c.ch))
1569 continue;
1570
1571 uart_insert_char(port, status, ATMEL_US_OVRE, c.ch, flg);
1572 }
1573
1574 tty_flip_buffer_push(&port->state->port);
1575}
1576
1577static void atmel_release_rx_pdc(struct uart_port *port)
1578{
1579 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1580 int i;
1581
1582 for (i = 0; i < 2; i++) {
1583 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1584
1585 dma_unmap_single(port->dev,
1586 pdc->dma_addr,
1587 pdc->dma_size,
1588 DMA_FROM_DEVICE);
1589 kfree(pdc->buf);
1590 }
1591}
1592
1593static void atmel_rx_from_pdc(struct uart_port *port)
1594{
1595 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1596 struct tty_port *tport = &port->state->port;
1597 struct atmel_dma_buffer *pdc;
1598 int rx_idx = atmel_port->pdc_rx_idx;
1599 unsigned int head;
1600 unsigned int tail;
1601 unsigned int count;
1602
1603 do {
1604 /* Reset the UART timeout early so that we don't miss one */
1605 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1606
1607 pdc = &atmel_port->pdc_rx[rx_idx];
1608 head = atmel_uart_readl(port, ATMEL_PDC_RPR) - pdc->dma_addr;
1609 tail = pdc->ofs;
1610
1611 /* If the PDC has switched buffers, RPR won't contain
1612 * any address within the current buffer. Since head
1613 * is unsigned, we just need a one-way comparison to
1614 * find out.
1615 *
1616 * In this case, we just need to consume the entire
1617 * buffer and resubmit it for DMA. This will clear the
1618 * ENDRX bit as well, so that we can safely re-enable
1619 * all interrupts below.
1620 */
1621 head = min(head, pdc->dma_size);
1622
1623 if (likely(head != tail)) {
1624 dma_sync_single_for_cpu(port->dev, pdc->dma_addr,
1625 pdc->dma_size, DMA_FROM_DEVICE);
1626
1627 /*
1628 * head will only wrap around when we recycle
1629 * the DMA buffer, and when that happens, we
1630 * explicitly set tail to 0. So head will
1631 * always be greater than tail.
1632 */
1633 count = head - tail;
1634
1635 tty_insert_flip_string(tport, pdc->buf + pdc->ofs,
1636 count);
1637
1638 dma_sync_single_for_device(port->dev, pdc->dma_addr,
1639 pdc->dma_size, DMA_FROM_DEVICE);
1640
1641 port->icount.rx += count;
1642 pdc->ofs = head;
1643 }
1644
1645 /*
1646 * If the current buffer is full, we need to check if
1647 * the next one contains any additional data.
1648 */
1649 if (head >= pdc->dma_size) {
1650 pdc->ofs = 0;
1651 atmel_uart_writel(port, ATMEL_PDC_RNPR, pdc->dma_addr);
1652 atmel_uart_writel(port, ATMEL_PDC_RNCR, pdc->dma_size);
1653
1654 rx_idx = !rx_idx;
1655 atmel_port->pdc_rx_idx = rx_idx;
1656 }
1657 } while (head >= pdc->dma_size);
1658
1659 tty_flip_buffer_push(tport);
1660
1661 atmel_uart_writel(port, ATMEL_US_IER,
1662 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1663}
1664
1665static int atmel_prepare_rx_pdc(struct uart_port *port)
1666{
1667 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1668 int i;
1669
1670 for (i = 0; i < 2; i++) {
1671 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1672
1673 pdc->buf = kmalloc(PDC_BUFFER_SIZE, GFP_KERNEL);
1674 if (pdc->buf == NULL) {
1675 if (i != 0) {
1676 dma_unmap_single(port->dev,
1677 atmel_port->pdc_rx[0].dma_addr,
1678 PDC_BUFFER_SIZE,
1679 DMA_FROM_DEVICE);
1680 kfree(atmel_port->pdc_rx[0].buf);
1681 }
1682 atmel_port->use_pdc_rx = false;
1683 return -ENOMEM;
1684 }
1685 pdc->dma_addr = dma_map_single(port->dev,
1686 pdc->buf,
1687 PDC_BUFFER_SIZE,
1688 DMA_FROM_DEVICE);
1689 pdc->dma_size = PDC_BUFFER_SIZE;
1690 pdc->ofs = 0;
1691 }
1692
1693 atmel_port->pdc_rx_idx = 0;
1694
1695 atmel_uart_writel(port, ATMEL_PDC_RPR, atmel_port->pdc_rx[0].dma_addr);
1696 atmel_uart_writel(port, ATMEL_PDC_RCR, PDC_BUFFER_SIZE);
1697
1698 atmel_uart_writel(port, ATMEL_PDC_RNPR,
1699 atmel_port->pdc_rx[1].dma_addr);
1700 atmel_uart_writel(port, ATMEL_PDC_RNCR, PDC_BUFFER_SIZE);
1701
1702 return 0;
1703}
1704
1705/*
1706 * tasklet handling tty stuff outside the interrupt handler.
1707 */
1708static void atmel_tasklet_rx_func(struct tasklet_struct *t)
1709{
1710 struct atmel_uart_port *atmel_port = from_tasklet(atmel_port, t,
1711 tasklet_rx);
1712 struct uart_port *port = &atmel_port->uart;
1713
1714 /* The interrupt handler does not take the lock */
1715 spin_lock(&port->lock);
1716 atmel_port->schedule_rx(port);
1717 spin_unlock(&port->lock);
1718}
1719
1720static void atmel_tasklet_tx_func(struct tasklet_struct *t)
1721{
1722 struct atmel_uart_port *atmel_port = from_tasklet(atmel_port, t,
1723 tasklet_tx);
1724 struct uart_port *port = &atmel_port->uart;
1725
1726 /* The interrupt handler does not take the lock */
1727 spin_lock(&port->lock);
1728 atmel_port->schedule_tx(port);
1729 spin_unlock(&port->lock);
1730}
1731
1732static void atmel_init_property(struct atmel_uart_port *atmel_port,
1733 struct platform_device *pdev)
1734{
1735 struct device_node *np = pdev->dev.of_node;
1736
1737 /* DMA/PDC usage specification */
1738 if (of_property_read_bool(np, "atmel,use-dma-rx")) {
1739 if (of_property_read_bool(np, "dmas")) {
1740 atmel_port->use_dma_rx = true;
1741 atmel_port->use_pdc_rx = false;
1742 } else {
1743 atmel_port->use_dma_rx = false;
1744 atmel_port->use_pdc_rx = true;
1745 }
1746 } else {
1747 atmel_port->use_dma_rx = false;
1748 atmel_port->use_pdc_rx = false;
1749 }
1750
1751 if (of_property_read_bool(np, "atmel,use-dma-tx")) {
1752 if (of_property_read_bool(np, "dmas")) {
1753 atmel_port->use_dma_tx = true;
1754 atmel_port->use_pdc_tx = false;
1755 } else {
1756 atmel_port->use_dma_tx = false;
1757 atmel_port->use_pdc_tx = true;
1758 }
1759 } else {
1760 atmel_port->use_dma_tx = false;
1761 atmel_port->use_pdc_tx = false;
1762 }
1763}
1764
1765static void atmel_set_ops(struct uart_port *port)
1766{
1767 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1768
1769 if (atmel_use_dma_rx(port)) {
1770 atmel_port->prepare_rx = &atmel_prepare_rx_dma;
1771 atmel_port->schedule_rx = &atmel_rx_from_dma;
1772 atmel_port->release_rx = &atmel_release_rx_dma;
1773 } else if (atmel_use_pdc_rx(port)) {
1774 atmel_port->prepare_rx = &atmel_prepare_rx_pdc;
1775 atmel_port->schedule_rx = &atmel_rx_from_pdc;
1776 atmel_port->release_rx = &atmel_release_rx_pdc;
1777 } else {
1778 atmel_port->prepare_rx = NULL;
1779 atmel_port->schedule_rx = &atmel_rx_from_ring;
1780 atmel_port->release_rx = NULL;
1781 }
1782
1783 if (atmel_use_dma_tx(port)) {
1784 atmel_port->prepare_tx = &atmel_prepare_tx_dma;
1785 atmel_port->schedule_tx = &atmel_tx_dma;
1786 atmel_port->release_tx = &atmel_release_tx_dma;
1787 } else if (atmel_use_pdc_tx(port)) {
1788 atmel_port->prepare_tx = &atmel_prepare_tx_pdc;
1789 atmel_port->schedule_tx = &atmel_tx_pdc;
1790 atmel_port->release_tx = &atmel_release_tx_pdc;
1791 } else {
1792 atmel_port->prepare_tx = NULL;
1793 atmel_port->schedule_tx = &atmel_tx_chars;
1794 atmel_port->release_tx = NULL;
1795 }
1796}
1797
1798/*
1799 * Get ip name usart or uart
1800 */
1801static void atmel_get_ip_name(struct uart_port *port)
1802{
1803 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1804 int name = atmel_uart_readl(port, ATMEL_US_NAME);
1805 u32 version;
1806 u32 usart, dbgu_uart, new_uart;
1807 /* ASCII decoding for IP version */
1808 usart = 0x55534152; /* USAR(T) */
1809 dbgu_uart = 0x44424755; /* DBGU */
1810 new_uart = 0x55415254; /* UART */
1811
1812 /*
1813 * Only USART devices from at91sam9260 SOC implement fractional
1814 * baudrate. It is available for all asynchronous modes, with the
1815 * following restriction: the sampling clock's duty cycle is not
1816 * constant.
1817 */
1818 atmel_port->has_frac_baudrate = false;
1819 atmel_port->has_hw_timer = false;
1820 atmel_port->is_usart = false;
1821
1822 if (name == new_uart) {
1823 dev_dbg(port->dev, "Uart with hw timer");
1824 atmel_port->has_hw_timer = true;
1825 atmel_port->rtor = ATMEL_UA_RTOR;
1826 } else if (name == usart) {
1827 dev_dbg(port->dev, "Usart\n");
1828 atmel_port->has_frac_baudrate = true;
1829 atmel_port->has_hw_timer = true;
1830 atmel_port->is_usart = true;
1831 atmel_port->rtor = ATMEL_US_RTOR;
1832 version = atmel_uart_readl(port, ATMEL_US_VERSION);
1833 switch (version) {
1834 case 0x814: /* sama5d2 */
1835 fallthrough;
1836 case 0x701: /* sama5d4 */
1837 atmel_port->fidi_min = 3;
1838 atmel_port->fidi_max = 65535;
1839 break;
1840 case 0x502: /* sam9x5, sama5d3 */
1841 atmel_port->fidi_min = 3;
1842 atmel_port->fidi_max = 2047;
1843 break;
1844 default:
1845 atmel_port->fidi_min = 1;
1846 atmel_port->fidi_max = 2047;
1847 }
1848 } else if (name == dbgu_uart) {
1849 dev_dbg(port->dev, "Dbgu or uart without hw timer\n");
1850 } else {
1851 /* fallback for older SoCs: use version field */
1852 version = atmel_uart_readl(port, ATMEL_US_VERSION);
1853 switch (version) {
1854 case 0x302:
1855 case 0x10213:
1856 case 0x10302:
1857 dev_dbg(port->dev, "This version is usart\n");
1858 atmel_port->has_frac_baudrate = true;
1859 atmel_port->has_hw_timer = true;
1860 atmel_port->is_usart = true;
1861 atmel_port->rtor = ATMEL_US_RTOR;
1862 break;
1863 case 0x203:
1864 case 0x10202:
1865 dev_dbg(port->dev, "This version is uart\n");
1866 break;
1867 default:
1868 dev_err(port->dev, "Not supported ip name nor version, set to uart\n");
1869 }
1870 }
1871}
1872
1873/*
1874 * Perform initialization and enable port for reception
1875 */
1876static int atmel_startup(struct uart_port *port)
1877{
1878 struct platform_device *pdev = to_platform_device(port->dev);
1879 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1880 int retval;
1881
1882 /*
1883 * Ensure that no interrupts are enabled otherwise when
1884 * request_irq() is called we could get stuck trying to
1885 * handle an unexpected interrupt
1886 */
1887 atmel_uart_writel(port, ATMEL_US_IDR, -1);
1888 atmel_port->ms_irq_enabled = false;
1889
1890 /*
1891 * Allocate the IRQ
1892 */
1893 retval = request_irq(port->irq, atmel_interrupt,
1894 IRQF_SHARED | IRQF_COND_SUSPEND,
1895 dev_name(&pdev->dev), port);
1896 if (retval) {
1897 dev_err(port->dev, "atmel_startup - Can't get irq\n");
1898 return retval;
1899 }
1900
1901 atomic_set(&atmel_port->tasklet_shutdown, 0);
1902 tasklet_setup(&atmel_port->tasklet_rx, atmel_tasklet_rx_func);
1903 tasklet_setup(&atmel_port->tasklet_tx, atmel_tasklet_tx_func);
1904
1905 /*
1906 * Initialize DMA (if necessary)
1907 */
1908 atmel_init_property(atmel_port, pdev);
1909 atmel_set_ops(port);
1910
1911 if (atmel_port->prepare_rx) {
1912 retval = atmel_port->prepare_rx(port);
1913 if (retval < 0)
1914 atmel_set_ops(port);
1915 }
1916
1917 if (atmel_port->prepare_tx) {
1918 retval = atmel_port->prepare_tx(port);
1919 if (retval < 0)
1920 atmel_set_ops(port);
1921 }
1922
1923 /*
1924 * Enable FIFO when available
1925 */
1926 if (atmel_port->fifo_size) {
1927 unsigned int txrdym = ATMEL_US_ONE_DATA;
1928 unsigned int rxrdym = ATMEL_US_ONE_DATA;
1929 unsigned int fmr;
1930
1931 atmel_uart_writel(port, ATMEL_US_CR,
1932 ATMEL_US_FIFOEN |
1933 ATMEL_US_RXFCLR |
1934 ATMEL_US_TXFLCLR);
1935
1936 if (atmel_use_dma_tx(port))
1937 txrdym = ATMEL_US_FOUR_DATA;
1938
1939 fmr = ATMEL_US_TXRDYM(txrdym) | ATMEL_US_RXRDYM(rxrdym);
1940 if (atmel_port->rts_high &&
1941 atmel_port->rts_low)
1942 fmr |= ATMEL_US_FRTSC |
1943 ATMEL_US_RXFTHRES(atmel_port->rts_high) |
1944 ATMEL_US_RXFTHRES2(atmel_port->rts_low);
1945
1946 atmel_uart_writel(port, ATMEL_US_FMR, fmr);
1947 }
1948
1949 /* Save current CSR for comparison in atmel_tasklet_func() */
1950 atmel_port->irq_status_prev = atmel_uart_readl(port, ATMEL_US_CSR);
1951
1952 /*
1953 * Finally, enable the serial port
1954 */
1955 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
1956 /* enable xmit & rcvr */
1957 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
1958 atmel_port->tx_stopped = false;
1959
1960 timer_setup(&atmel_port->uart_timer, atmel_uart_timer_callback, 0);
1961
1962 if (atmel_use_pdc_rx(port)) {
1963 /* set UART timeout */
1964 if (!atmel_port->has_hw_timer) {
1965 mod_timer(&atmel_port->uart_timer,
1966 jiffies + uart_poll_timeout(port));
1967 /* set USART timeout */
1968 } else {
1969 atmel_uart_writel(port, atmel_port->rtor,
1970 PDC_RX_TIMEOUT);
1971 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1972
1973 atmel_uart_writel(port, ATMEL_US_IER,
1974 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1975 }
1976 /* enable PDC controller */
1977 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
1978 } else if (atmel_use_dma_rx(port)) {
1979 /* set UART timeout */
1980 if (!atmel_port->has_hw_timer) {
1981 mod_timer(&atmel_port->uart_timer,
1982 jiffies + uart_poll_timeout(port));
1983 /* set USART timeout */
1984 } else {
1985 atmel_uart_writel(port, atmel_port->rtor,
1986 PDC_RX_TIMEOUT);
1987 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1988
1989 atmel_uart_writel(port, ATMEL_US_IER,
1990 ATMEL_US_TIMEOUT);
1991 }
1992 } else {
1993 /* enable receive only */
1994 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY);
1995 }
1996
1997 return 0;
1998}
1999
2000/*
2001 * Flush any TX data submitted for DMA. Called when the TX circular
2002 * buffer is reset.
2003 */
2004static void atmel_flush_buffer(struct uart_port *port)
2005{
2006 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2007
2008 if (atmel_use_pdc_tx(port)) {
2009 atmel_uart_writel(port, ATMEL_PDC_TCR, 0);
2010 atmel_port->pdc_tx.ofs = 0;
2011 }
2012 /*
2013 * in uart_flush_buffer(), the xmit circular buffer has just
2014 * been cleared, so we have to reset tx_len accordingly.
2015 */
2016 atmel_port->tx_len = 0;
2017}
2018
2019/*
2020 * Disable the port
2021 */
2022static void atmel_shutdown(struct uart_port *port)
2023{
2024 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2025
2026 /* Disable modem control lines interrupts */
2027 atmel_disable_ms(port);
2028
2029 /* Disable interrupts at device level */
2030 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2031
2032 /* Prevent spurious interrupts from scheduling the tasklet */
2033 atomic_inc(&atmel_port->tasklet_shutdown);
2034
2035 /*
2036 * Prevent any tasklets being scheduled during
2037 * cleanup
2038 */
2039 del_timer_sync(&atmel_port->uart_timer);
2040
2041 /* Make sure that no interrupt is on the fly */
2042 synchronize_irq(port->irq);
2043
2044 /*
2045 * Clear out any scheduled tasklets before
2046 * we destroy the buffers
2047 */
2048 tasklet_kill(&atmel_port->tasklet_rx);
2049 tasklet_kill(&atmel_port->tasklet_tx);
2050
2051 /*
2052 * Ensure everything is stopped and
2053 * disable port and break condition.
2054 */
2055 atmel_stop_rx(port);
2056 atmel_stop_tx(port);
2057
2058 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
2059
2060 /*
2061 * Shut-down the DMA.
2062 */
2063 if (atmel_port->release_rx)
2064 atmel_port->release_rx(port);
2065 if (atmel_port->release_tx)
2066 atmel_port->release_tx(port);
2067
2068 /*
2069 * Reset ring buffer pointers
2070 */
2071 atmel_port->rx_ring.head = 0;
2072 atmel_port->rx_ring.tail = 0;
2073
2074 /*
2075 * Free the interrupts
2076 */
2077 free_irq(port->irq, port);
2078
2079 atmel_flush_buffer(port);
2080}
2081
2082/*
2083 * Power / Clock management.
2084 */
2085static void atmel_serial_pm(struct uart_port *port, unsigned int state,
2086 unsigned int oldstate)
2087{
2088 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2089
2090 switch (state) {
2091 case UART_PM_STATE_ON:
2092 /*
2093 * Enable the peripheral clock for this serial port.
2094 * This is called on uart_open() or a resume event.
2095 */
2096 clk_prepare_enable(atmel_port->clk);
2097
2098 /* re-enable interrupts if we disabled some on suspend */
2099 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->backup_imr);
2100 break;
2101 case UART_PM_STATE_OFF:
2102 /* Back up the interrupt mask and disable all interrupts */
2103 atmel_port->backup_imr = atmel_uart_readl(port, ATMEL_US_IMR);
2104 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2105
2106 /*
2107 * Disable the peripheral clock for this serial port.
2108 * This is called on uart_close() or a suspend event.
2109 */
2110 clk_disable_unprepare(atmel_port->clk);
2111 if (__clk_is_enabled(atmel_port->gclk))
2112 clk_disable_unprepare(atmel_port->gclk);
2113 break;
2114 default:
2115 dev_err(port->dev, "atmel_serial: unknown pm %d\n", state);
2116 }
2117}
2118
2119/*
2120 * Change the port parameters
2121 */
2122static void atmel_set_termios(struct uart_port *port,
2123 struct ktermios *termios,
2124 const struct ktermios *old)
2125{
2126 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2127 unsigned long flags;
2128 unsigned int old_mode, mode, imr, quot, div, cd, fp = 0;
2129 unsigned int baud, actual_baud, gclk_rate;
2130 int ret;
2131
2132 /* save the current mode register */
2133 mode = old_mode = atmel_uart_readl(port, ATMEL_US_MR);
2134
2135 /* reset the mode, clock divisor, parity, stop bits and data size */
2136 if (atmel_port->is_usart)
2137 mode &= ~(ATMEL_US_NBSTOP | ATMEL_US_PAR | ATMEL_US_CHRL |
2138 ATMEL_US_USCLKS | ATMEL_US_USMODE);
2139 else
2140 mode &= ~(ATMEL_UA_BRSRCCK | ATMEL_US_PAR | ATMEL_UA_FILTER);
2141
2142 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
2143
2144 /* byte size */
2145 switch (termios->c_cflag & CSIZE) {
2146 case CS5:
2147 mode |= ATMEL_US_CHRL_5;
2148 break;
2149 case CS6:
2150 mode |= ATMEL_US_CHRL_6;
2151 break;
2152 case CS7:
2153 mode |= ATMEL_US_CHRL_7;
2154 break;
2155 default:
2156 mode |= ATMEL_US_CHRL_8;
2157 break;
2158 }
2159
2160 /* stop bits */
2161 if (termios->c_cflag & CSTOPB)
2162 mode |= ATMEL_US_NBSTOP_2;
2163
2164 /* parity */
2165 if (termios->c_cflag & PARENB) {
2166 /* Mark or Space parity */
2167 if (termios->c_cflag & CMSPAR) {
2168 if (termios->c_cflag & PARODD)
2169 mode |= ATMEL_US_PAR_MARK;
2170 else
2171 mode |= ATMEL_US_PAR_SPACE;
2172 } else if (termios->c_cflag & PARODD)
2173 mode |= ATMEL_US_PAR_ODD;
2174 else
2175 mode |= ATMEL_US_PAR_EVEN;
2176 } else
2177 mode |= ATMEL_US_PAR_NONE;
2178
2179 spin_lock_irqsave(&port->lock, flags);
2180
2181 port->read_status_mask = ATMEL_US_OVRE;
2182 if (termios->c_iflag & INPCK)
2183 port->read_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
2184 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
2185 port->read_status_mask |= ATMEL_US_RXBRK;
2186
2187 if (atmel_use_pdc_rx(port))
2188 /* need to enable error interrupts */
2189 atmel_uart_writel(port, ATMEL_US_IER, port->read_status_mask);
2190
2191 /*
2192 * Characters to ignore
2193 */
2194 port->ignore_status_mask = 0;
2195 if (termios->c_iflag & IGNPAR)
2196 port->ignore_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
2197 if (termios->c_iflag & IGNBRK) {
2198 port->ignore_status_mask |= ATMEL_US_RXBRK;
2199 /*
2200 * If we're ignoring parity and break indicators,
2201 * ignore overruns too (for real raw support).
2202 */
2203 if (termios->c_iflag & IGNPAR)
2204 port->ignore_status_mask |= ATMEL_US_OVRE;
2205 }
2206 /* TODO: Ignore all characters if CREAD is set.*/
2207
2208 /* update the per-port timeout */
2209 uart_update_timeout(port, termios->c_cflag, baud);
2210
2211 /*
2212 * save/disable interrupts. The tty layer will ensure that the
2213 * transmitter is empty if requested by the caller, so there's
2214 * no need to wait for it here.
2215 */
2216 imr = atmel_uart_readl(port, ATMEL_US_IMR);
2217 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2218
2219 /* disable receiver and transmitter */
2220 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
2221 atmel_port->tx_stopped = true;
2222
2223 /* mode */
2224 if (port->rs485.flags & SER_RS485_ENABLED) {
2225 atmel_uart_writel(port, ATMEL_US_TTGR,
2226 port->rs485.delay_rts_after_send);
2227 mode |= ATMEL_US_USMODE_RS485;
2228 } else if (port->iso7816.flags & SER_ISO7816_ENABLED) {
2229 atmel_uart_writel(port, ATMEL_US_TTGR, port->iso7816.tg);
2230 /* select mck clock, and output */
2231 mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO;
2232 /* set max iterations */
2233 mode |= ATMEL_US_MAX_ITER(3);
2234 if ((port->iso7816.flags & SER_ISO7816_T_PARAM)
2235 == SER_ISO7816_T(0))
2236 mode |= ATMEL_US_USMODE_ISO7816_T0;
2237 else
2238 mode |= ATMEL_US_USMODE_ISO7816_T1;
2239 } else if (termios->c_cflag & CRTSCTS) {
2240 /* RS232 with hardware handshake (RTS/CTS) */
2241 if (atmel_use_fifo(port) &&
2242 !mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS)) {
2243 /*
2244 * with ATMEL_US_USMODE_HWHS set, the controller will
2245 * be able to drive the RTS pin high/low when the RX
2246 * FIFO is above RXFTHRES/below RXFTHRES2.
2247 * It will also disable the transmitter when the CTS
2248 * pin is high.
2249 * This mode is not activated if CTS pin is a GPIO
2250 * because in this case, the transmitter is always
2251 * disabled (there must be an internal pull-up
2252 * responsible for this behaviour).
2253 * If the RTS pin is a GPIO, the controller won't be
2254 * able to drive it according to the FIFO thresholds,
2255 * but it will be handled by the driver.
2256 */
2257 mode |= ATMEL_US_USMODE_HWHS;
2258 } else {
2259 /*
2260 * For platforms without FIFO, the flow control is
2261 * handled by the driver.
2262 */
2263 mode |= ATMEL_US_USMODE_NORMAL;
2264 }
2265 } else {
2266 /* RS232 without hadware handshake */
2267 mode |= ATMEL_US_USMODE_NORMAL;
2268 }
2269
2270 /*
2271 * Set the baud rate:
2272 * Fractional baudrate allows to setup output frequency more
2273 * accurately. This feature is enabled only when using normal mode.
2274 * baudrate = selected clock / (8 * (2 - OVER) * (CD + FP / 8))
2275 * Currently, OVER is always set to 0 so we get
2276 * baudrate = selected clock / (16 * (CD + FP / 8))
2277 * then
2278 * 8 CD + FP = selected clock / (2 * baudrate)
2279 */
2280 if (atmel_port->has_frac_baudrate) {
2281 div = DIV_ROUND_CLOSEST(port->uartclk, baud * 2);
2282 cd = div >> 3;
2283 fp = div & ATMEL_US_FP_MASK;
2284 } else {
2285 cd = uart_get_divisor(port, baud);
2286 }
2287
2288 /*
2289 * If the current value of the Clock Divisor surpasses the 16 bit
2290 * ATMEL_US_CD mask and the IP is USART, switch to the Peripheral
2291 * Clock implicitly divided by 8.
2292 * If the IP is UART however, keep the highest possible value for
2293 * the CD and avoid needless division of CD, since UART IP's do not
2294 * support implicit division of the Peripheral Clock.
2295 */
2296 if (atmel_port->is_usart && cd > ATMEL_US_CD) {
2297 cd /= 8;
2298 mode |= ATMEL_US_USCLKS_MCK_DIV8;
2299 } else {
2300 cd = min_t(unsigned int, cd, ATMEL_US_CD);
2301 }
2302
2303 /*
2304 * If there is no Fractional Part, there is a high chance that
2305 * we may be able to generate a baudrate closer to the desired one
2306 * if we use the GCLK as the clock source driving the baudrate
2307 * generator.
2308 */
2309 if (!atmel_port->has_frac_baudrate) {
2310 if (__clk_is_enabled(atmel_port->gclk))
2311 clk_disable_unprepare(atmel_port->gclk);
2312 gclk_rate = clk_round_rate(atmel_port->gclk, 16 * baud);
2313 actual_baud = clk_get_rate(atmel_port->clk) / (16 * cd);
2314 if (gclk_rate && abs(atmel_error_rate(baud, actual_baud)) >
2315 abs(atmel_error_rate(baud, gclk_rate / 16))) {
2316 clk_set_rate(atmel_port->gclk, 16 * baud);
2317 ret = clk_prepare_enable(atmel_port->gclk);
2318 if (ret)
2319 goto gclk_fail;
2320
2321 if (atmel_port->is_usart) {
2322 mode &= ~ATMEL_US_USCLKS;
2323 mode |= ATMEL_US_USCLKS_GCLK;
2324 } else {
2325 mode |= ATMEL_UA_BRSRCCK;
2326 }
2327
2328 /*
2329 * Set the Clock Divisor for GCLK to 1.
2330 * Since we were able to generate the smallest
2331 * multiple of the desired baudrate times 16,
2332 * then we surely can generate a bigger multiple
2333 * with the exact error rate for an equally increased
2334 * CD. Thus no need to take into account
2335 * a higher value for CD.
2336 */
2337 cd = 1;
2338 }
2339 }
2340
2341gclk_fail:
2342 quot = cd | fp << ATMEL_US_FP_OFFSET;
2343
2344 if (!(port->iso7816.flags & SER_ISO7816_ENABLED))
2345 atmel_uart_writel(port, ATMEL_US_BRGR, quot);
2346
2347 /* set the mode, clock divisor, parity, stop bits and data size */
2348 atmel_uart_writel(port, ATMEL_US_MR, mode);
2349
2350 /*
2351 * when switching the mode, set the RTS line state according to the
2352 * new mode, otherwise keep the former state
2353 */
2354 if ((old_mode & ATMEL_US_USMODE) != (mode & ATMEL_US_USMODE)) {
2355 unsigned int rts_state;
2356
2357 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) {
2358 /* let the hardware control the RTS line */
2359 rts_state = ATMEL_US_RTSDIS;
2360 } else {
2361 /* force RTS line to low level */
2362 rts_state = ATMEL_US_RTSEN;
2363 }
2364
2365 atmel_uart_writel(port, ATMEL_US_CR, rts_state);
2366 }
2367
2368 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
2369 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
2370 atmel_port->tx_stopped = false;
2371
2372 /* restore interrupts */
2373 atmel_uart_writel(port, ATMEL_US_IER, imr);
2374
2375 /* CTS flow-control and modem-status interrupts */
2376 if (UART_ENABLE_MS(port, termios->c_cflag))
2377 atmel_enable_ms(port);
2378 else
2379 atmel_disable_ms(port);
2380
2381 spin_unlock_irqrestore(&port->lock, flags);
2382}
2383
2384static void atmel_set_ldisc(struct uart_port *port, struct ktermios *termios)
2385{
2386 if (termios->c_line == N_PPS) {
2387 port->flags |= UPF_HARDPPS_CD;
2388 spin_lock_irq(&port->lock);
2389 atmel_enable_ms(port);
2390 spin_unlock_irq(&port->lock);
2391 } else {
2392 port->flags &= ~UPF_HARDPPS_CD;
2393 if (!UART_ENABLE_MS(port, termios->c_cflag)) {
2394 spin_lock_irq(&port->lock);
2395 atmel_disable_ms(port);
2396 spin_unlock_irq(&port->lock);
2397 }
2398 }
2399}
2400
2401/*
2402 * Return string describing the specified port
2403 */
2404static const char *atmel_type(struct uart_port *port)
2405{
2406 return (port->type == PORT_ATMEL) ? "ATMEL_SERIAL" : NULL;
2407}
2408
2409/*
2410 * Release the memory region(s) being used by 'port'.
2411 */
2412static void atmel_release_port(struct uart_port *port)
2413{
2414 struct platform_device *mpdev = to_platform_device(port->dev->parent);
2415 int size = resource_size(mpdev->resource);
2416
2417 release_mem_region(port->mapbase, size);
2418
2419 if (port->flags & UPF_IOREMAP) {
2420 iounmap(port->membase);
2421 port->membase = NULL;
2422 }
2423}
2424
2425/*
2426 * Request the memory region(s) being used by 'port'.
2427 */
2428static int atmel_request_port(struct uart_port *port)
2429{
2430 struct platform_device *mpdev = to_platform_device(port->dev->parent);
2431 int size = resource_size(mpdev->resource);
2432
2433 if (!request_mem_region(port->mapbase, size, "atmel_serial"))
2434 return -EBUSY;
2435
2436 if (port->flags & UPF_IOREMAP) {
2437 port->membase = ioremap(port->mapbase, size);
2438 if (port->membase == NULL) {
2439 release_mem_region(port->mapbase, size);
2440 return -ENOMEM;
2441 }
2442 }
2443
2444 return 0;
2445}
2446
2447/*
2448 * Configure/autoconfigure the port.
2449 */
2450static void atmel_config_port(struct uart_port *port, int flags)
2451{
2452 if (flags & UART_CONFIG_TYPE) {
2453 port->type = PORT_ATMEL;
2454 atmel_request_port(port);
2455 }
2456}
2457
2458/*
2459 * Verify the new serial_struct (for TIOCSSERIAL).
2460 */
2461static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser)
2462{
2463 int ret = 0;
2464 if (ser->type != PORT_UNKNOWN && ser->type != PORT_ATMEL)
2465 ret = -EINVAL;
2466 if (port->irq != ser->irq)
2467 ret = -EINVAL;
2468 if (ser->io_type != SERIAL_IO_MEM)
2469 ret = -EINVAL;
2470 if (port->uartclk / 16 != ser->baud_base)
2471 ret = -EINVAL;
2472 if (port->mapbase != (unsigned long)ser->iomem_base)
2473 ret = -EINVAL;
2474 if (port->iobase != ser->port)
2475 ret = -EINVAL;
2476 if (ser->hub6 != 0)
2477 ret = -EINVAL;
2478 return ret;
2479}
2480
2481#ifdef CONFIG_CONSOLE_POLL
2482static int atmel_poll_get_char(struct uart_port *port)
2483{
2484 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_RXRDY))
2485 cpu_relax();
2486
2487 return atmel_uart_read_char(port);
2488}
2489
2490static void atmel_poll_put_char(struct uart_port *port, unsigned char ch)
2491{
2492 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
2493 cpu_relax();
2494
2495 atmel_uart_write_char(port, ch);
2496}
2497#endif
2498
2499static const struct uart_ops atmel_pops = {
2500 .tx_empty = atmel_tx_empty,
2501 .set_mctrl = atmel_set_mctrl,
2502 .get_mctrl = atmel_get_mctrl,
2503 .stop_tx = atmel_stop_tx,
2504 .start_tx = atmel_start_tx,
2505 .stop_rx = atmel_stop_rx,
2506 .enable_ms = atmel_enable_ms,
2507 .break_ctl = atmel_break_ctl,
2508 .startup = atmel_startup,
2509 .shutdown = atmel_shutdown,
2510 .flush_buffer = atmel_flush_buffer,
2511 .set_termios = atmel_set_termios,
2512 .set_ldisc = atmel_set_ldisc,
2513 .type = atmel_type,
2514 .release_port = atmel_release_port,
2515 .request_port = atmel_request_port,
2516 .config_port = atmel_config_port,
2517 .verify_port = atmel_verify_port,
2518 .pm = atmel_serial_pm,
2519#ifdef CONFIG_CONSOLE_POLL
2520 .poll_get_char = atmel_poll_get_char,
2521 .poll_put_char = atmel_poll_put_char,
2522#endif
2523};
2524
2525static const struct serial_rs485 atmel_rs485_supported = {
2526 .flags = SER_RS485_ENABLED | SER_RS485_RTS_AFTER_SEND | SER_RS485_RX_DURING_TX,
2527 .delay_rts_before_send = 1,
2528 .delay_rts_after_send = 1,
2529};
2530
2531/*
2532 * Configure the port from the platform device resource info.
2533 */
2534static int atmel_init_port(struct atmel_uart_port *atmel_port,
2535 struct platform_device *pdev)
2536{
2537 int ret;
2538 struct uart_port *port = &atmel_port->uart;
2539 struct platform_device *mpdev = to_platform_device(pdev->dev.parent);
2540
2541 atmel_init_property(atmel_port, pdev);
2542 atmel_set_ops(port);
2543
2544 port->iotype = UPIO_MEM;
2545 port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
2546 port->ops = &atmel_pops;
2547 port->fifosize = 1;
2548 port->dev = &pdev->dev;
2549 port->mapbase = mpdev->resource[0].start;
2550 port->irq = platform_get_irq(mpdev, 0);
2551 port->rs485_config = atmel_config_rs485;
2552 port->rs485_supported = atmel_rs485_supported;
2553 port->iso7816_config = atmel_config_iso7816;
2554 port->membase = NULL;
2555
2556 memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
2557
2558 ret = uart_get_rs485_mode(port);
2559 if (ret)
2560 return ret;
2561
2562 port->uartclk = clk_get_rate(atmel_port->clk);
2563
2564 /*
2565 * Use TXEMPTY for interrupt when rs485 or ISO7816 else TXRDY or
2566 * ENDTX|TXBUFE
2567 */
2568 if (atmel_uart_is_half_duplex(port))
2569 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
2570 else if (atmel_use_pdc_tx(port)) {
2571 port->fifosize = PDC_BUFFER_SIZE;
2572 atmel_port->tx_done_mask = ATMEL_US_ENDTX | ATMEL_US_TXBUFE;
2573 } else {
2574 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
2575 }
2576
2577 return 0;
2578}
2579
2580#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
2581static void atmel_console_putchar(struct uart_port *port, unsigned char ch)
2582{
2583 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
2584 cpu_relax();
2585 atmel_uart_write_char(port, ch);
2586}
2587
2588/*
2589 * Interrupts are disabled on entering
2590 */
2591static void atmel_console_write(struct console *co, const char *s, u_int count)
2592{
2593 struct uart_port *port = &atmel_ports[co->index].uart;
2594 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2595 unsigned int status, imr;
2596 unsigned int pdc_tx;
2597
2598 /*
2599 * First, save IMR and then disable interrupts
2600 */
2601 imr = atmel_uart_readl(port, ATMEL_US_IMR);
2602 atmel_uart_writel(port, ATMEL_US_IDR,
2603 ATMEL_US_RXRDY | atmel_port->tx_done_mask);
2604
2605 /* Store PDC transmit status and disable it */
2606 pdc_tx = atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN;
2607 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
2608
2609 /* Make sure that tx path is actually able to send characters */
2610 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
2611 atmel_port->tx_stopped = false;
2612
2613 uart_console_write(port, s, count, atmel_console_putchar);
2614
2615 /*
2616 * Finally, wait for transmitter to become empty
2617 * and restore IMR
2618 */
2619 do {
2620 status = atmel_uart_readl(port, ATMEL_US_CSR);
2621 } while (!(status & ATMEL_US_TXRDY));
2622
2623 /* Restore PDC transmit status */
2624 if (pdc_tx)
2625 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
2626
2627 /* set interrupts back the way they were */
2628 atmel_uart_writel(port, ATMEL_US_IER, imr);
2629}
2630
2631/*
2632 * If the port was already initialised (eg, by a boot loader),
2633 * try to determine the current setup.
2634 */
2635static void __init atmel_console_get_options(struct uart_port *port, int *baud,
2636 int *parity, int *bits)
2637{
2638 unsigned int mr, quot;
2639
2640 /*
2641 * If the baud rate generator isn't running, the port wasn't
2642 * initialized by the boot loader.
2643 */
2644 quot = atmel_uart_readl(port, ATMEL_US_BRGR) & ATMEL_US_CD;
2645 if (!quot)
2646 return;
2647
2648 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_CHRL;
2649 if (mr == ATMEL_US_CHRL_8)
2650 *bits = 8;
2651 else
2652 *bits = 7;
2653
2654 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_PAR;
2655 if (mr == ATMEL_US_PAR_EVEN)
2656 *parity = 'e';
2657 else if (mr == ATMEL_US_PAR_ODD)
2658 *parity = 'o';
2659
2660 *baud = port->uartclk / (16 * quot);
2661}
2662
2663static int __init atmel_console_setup(struct console *co, char *options)
2664{
2665 struct uart_port *port = &atmel_ports[co->index].uart;
2666 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2667 int baud = 115200;
2668 int bits = 8;
2669 int parity = 'n';
2670 int flow = 'n';
2671
2672 if (port->membase == NULL) {
2673 /* Port not initialized yet - delay setup */
2674 return -ENODEV;
2675 }
2676
2677 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2678 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
2679 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
2680 atmel_port->tx_stopped = false;
2681
2682 if (options)
2683 uart_parse_options(options, &baud, &parity, &bits, &flow);
2684 else
2685 atmel_console_get_options(port, &baud, &parity, &bits);
2686
2687 return uart_set_options(port, co, baud, parity, bits, flow);
2688}
2689
2690static struct uart_driver atmel_uart;
2691
2692static struct console atmel_console = {
2693 .name = ATMEL_DEVICENAME,
2694 .write = atmel_console_write,
2695 .device = uart_console_device,
2696 .setup = atmel_console_setup,
2697 .flags = CON_PRINTBUFFER,
2698 .index = -1,
2699 .data = &atmel_uart,
2700};
2701
2702static void atmel_serial_early_write(struct console *con, const char *s,
2703 unsigned int n)
2704{
2705 struct earlycon_device *dev = con->data;
2706
2707 uart_console_write(&dev->port, s, n, atmel_console_putchar);
2708}
2709
2710static int __init atmel_early_console_setup(struct earlycon_device *device,
2711 const char *options)
2712{
2713 if (!device->port.membase)
2714 return -ENODEV;
2715
2716 device->con->write = atmel_serial_early_write;
2717
2718 return 0;
2719}
2720
2721OF_EARLYCON_DECLARE(atmel_serial, "atmel,at91rm9200-usart",
2722 atmel_early_console_setup);
2723OF_EARLYCON_DECLARE(atmel_serial, "atmel,at91sam9260-usart",
2724 atmel_early_console_setup);
2725
2726#define ATMEL_CONSOLE_DEVICE (&atmel_console)
2727
2728#else
2729#define ATMEL_CONSOLE_DEVICE NULL
2730#endif
2731
2732static struct uart_driver atmel_uart = {
2733 .owner = THIS_MODULE,
2734 .driver_name = "atmel_serial",
2735 .dev_name = ATMEL_DEVICENAME,
2736 .major = SERIAL_ATMEL_MAJOR,
2737 .minor = MINOR_START,
2738 .nr = ATMEL_MAX_UART,
2739 .cons = ATMEL_CONSOLE_DEVICE,
2740};
2741
2742static bool atmel_serial_clk_will_stop(void)
2743{
2744#ifdef CONFIG_ARCH_AT91
2745 return at91_suspend_entering_slow_clock();
2746#else
2747 return false;
2748#endif
2749}
2750
2751static int __maybe_unused atmel_serial_suspend(struct device *dev)
2752{
2753 struct uart_port *port = dev_get_drvdata(dev);
2754 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2755
2756 if (uart_console(port) && console_suspend_enabled) {
2757 /* Drain the TX shifter */
2758 while (!(atmel_uart_readl(port, ATMEL_US_CSR) &
2759 ATMEL_US_TXEMPTY))
2760 cpu_relax();
2761 }
2762
2763 if (uart_console(port) && !console_suspend_enabled) {
2764 /* Cache register values as we won't get a full shutdown/startup
2765 * cycle
2766 */
2767 atmel_port->cache.mr = atmel_uart_readl(port, ATMEL_US_MR);
2768 atmel_port->cache.imr = atmel_uart_readl(port, ATMEL_US_IMR);
2769 atmel_port->cache.brgr = atmel_uart_readl(port, ATMEL_US_BRGR);
2770 atmel_port->cache.rtor = atmel_uart_readl(port,
2771 atmel_port->rtor);
2772 atmel_port->cache.ttgr = atmel_uart_readl(port, ATMEL_US_TTGR);
2773 atmel_port->cache.fmr = atmel_uart_readl(port, ATMEL_US_FMR);
2774 atmel_port->cache.fimr = atmel_uart_readl(port, ATMEL_US_FIMR);
2775 }
2776
2777 /* we can not wake up if we're running on slow clock */
2778 atmel_port->may_wakeup = device_may_wakeup(dev);
2779 if (atmel_serial_clk_will_stop()) {
2780 unsigned long flags;
2781
2782 spin_lock_irqsave(&atmel_port->lock_suspended, flags);
2783 atmel_port->suspended = true;
2784 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags);
2785 device_set_wakeup_enable(dev, 0);
2786 }
2787
2788 uart_suspend_port(&atmel_uart, port);
2789
2790 return 0;
2791}
2792
2793static int __maybe_unused atmel_serial_resume(struct device *dev)
2794{
2795 struct uart_port *port = dev_get_drvdata(dev);
2796 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2797 unsigned long flags;
2798
2799 if (uart_console(port) && !console_suspend_enabled) {
2800 atmel_uart_writel(port, ATMEL_US_MR, atmel_port->cache.mr);
2801 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->cache.imr);
2802 atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->cache.brgr);
2803 atmel_uart_writel(port, atmel_port->rtor,
2804 atmel_port->cache.rtor);
2805 atmel_uart_writel(port, ATMEL_US_TTGR, atmel_port->cache.ttgr);
2806
2807 if (atmel_port->fifo_size) {
2808 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_FIFOEN |
2809 ATMEL_US_RXFCLR | ATMEL_US_TXFLCLR);
2810 atmel_uart_writel(port, ATMEL_US_FMR,
2811 atmel_port->cache.fmr);
2812 atmel_uart_writel(port, ATMEL_US_FIER,
2813 atmel_port->cache.fimr);
2814 }
2815 atmel_start_rx(port);
2816 }
2817
2818 spin_lock_irqsave(&atmel_port->lock_suspended, flags);
2819 if (atmel_port->pending) {
2820 atmel_handle_receive(port, atmel_port->pending);
2821 atmel_handle_status(port, atmel_port->pending,
2822 atmel_port->pending_status);
2823 atmel_handle_transmit(port, atmel_port->pending);
2824 atmel_port->pending = 0;
2825 }
2826 atmel_port->suspended = false;
2827 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags);
2828
2829 uart_resume_port(&atmel_uart, port);
2830 device_set_wakeup_enable(dev, atmel_port->may_wakeup);
2831
2832 return 0;
2833}
2834
2835static void atmel_serial_probe_fifos(struct atmel_uart_port *atmel_port,
2836 struct platform_device *pdev)
2837{
2838 atmel_port->fifo_size = 0;
2839 atmel_port->rts_low = 0;
2840 atmel_port->rts_high = 0;
2841
2842 if (of_property_read_u32(pdev->dev.of_node,
2843 "atmel,fifo-size",
2844 &atmel_port->fifo_size))
2845 return;
2846
2847 if (!atmel_port->fifo_size)
2848 return;
2849
2850 if (atmel_port->fifo_size < ATMEL_MIN_FIFO_SIZE) {
2851 atmel_port->fifo_size = 0;
2852 dev_err(&pdev->dev, "Invalid FIFO size\n");
2853 return;
2854 }
2855
2856 /*
2857 * 0 <= rts_low <= rts_high <= fifo_size
2858 * Once their CTS line asserted by the remote peer, some x86 UARTs tend
2859 * to flush their internal TX FIFO, commonly up to 16 data, before
2860 * actually stopping to send new data. So we try to set the RTS High
2861 * Threshold to a reasonably high value respecting this 16 data
2862 * empirical rule when possible.
2863 */
2864 atmel_port->rts_high = max_t(int, atmel_port->fifo_size >> 1,
2865 atmel_port->fifo_size - ATMEL_RTS_HIGH_OFFSET);
2866 atmel_port->rts_low = max_t(int, atmel_port->fifo_size >> 2,
2867 atmel_port->fifo_size - ATMEL_RTS_LOW_OFFSET);
2868
2869 dev_info(&pdev->dev, "Using FIFO (%u data)\n",
2870 atmel_port->fifo_size);
2871 dev_dbg(&pdev->dev, "RTS High Threshold : %2u data\n",
2872 atmel_port->rts_high);
2873 dev_dbg(&pdev->dev, "RTS Low Threshold : %2u data\n",
2874 atmel_port->rts_low);
2875}
2876
2877static int atmel_serial_probe(struct platform_device *pdev)
2878{
2879 struct atmel_uart_port *atmel_port;
2880 struct device_node *np = pdev->dev.parent->of_node;
2881 void *data;
2882 int ret;
2883 bool rs485_enabled;
2884
2885 BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
2886
2887 /*
2888 * In device tree there is no node with "atmel,at91rm9200-usart-serial"
2889 * as compatible string. This driver is probed by at91-usart mfd driver
2890 * which is just a wrapper over the atmel_serial driver and
2891 * spi-at91-usart driver. All attributes needed by this driver are
2892 * found in of_node of parent.
2893 */
2894 pdev->dev.of_node = np;
2895
2896 ret = of_alias_get_id(np, "serial");
2897 if (ret < 0)
2898 /* port id not found in platform data nor device-tree aliases:
2899 * auto-enumerate it */
2900 ret = find_first_zero_bit(atmel_ports_in_use, ATMEL_MAX_UART);
2901
2902 if (ret >= ATMEL_MAX_UART) {
2903 ret = -ENODEV;
2904 goto err;
2905 }
2906
2907 if (test_and_set_bit(ret, atmel_ports_in_use)) {
2908 /* port already in use */
2909 ret = -EBUSY;
2910 goto err;
2911 }
2912
2913 atmel_port = &atmel_ports[ret];
2914 atmel_port->backup_imr = 0;
2915 atmel_port->uart.line = ret;
2916 atmel_port->uart.has_sysrq = IS_ENABLED(CONFIG_SERIAL_ATMEL_CONSOLE);
2917 atmel_serial_probe_fifos(atmel_port, pdev);
2918
2919 atomic_set(&atmel_port->tasklet_shutdown, 0);
2920 spin_lock_init(&atmel_port->lock_suspended);
2921
2922 atmel_port->clk = devm_clk_get(&pdev->dev, "usart");
2923 if (IS_ERR(atmel_port->clk)) {
2924 ret = PTR_ERR(atmel_port->clk);
2925 goto err;
2926 }
2927 ret = clk_prepare_enable(atmel_port->clk);
2928 if (ret)
2929 goto err;
2930
2931 atmel_port->gclk = devm_clk_get_optional(&pdev->dev, "gclk");
2932 if (IS_ERR(atmel_port->gclk)) {
2933 ret = PTR_ERR(atmel_port->gclk);
2934 goto err_clk_disable_unprepare;
2935 }
2936
2937 ret = atmel_init_port(atmel_port, pdev);
2938 if (ret)
2939 goto err_clk_disable_unprepare;
2940
2941 atmel_port->gpios = mctrl_gpio_init(&atmel_port->uart, 0);
2942 if (IS_ERR(atmel_port->gpios)) {
2943 ret = PTR_ERR(atmel_port->gpios);
2944 goto err_clk_disable_unprepare;
2945 }
2946
2947 if (!atmel_use_pdc_rx(&atmel_port->uart)) {
2948 ret = -ENOMEM;
2949 data = kmalloc_array(ATMEL_SERIAL_RINGSIZE,
2950 sizeof(struct atmel_uart_char),
2951 GFP_KERNEL);
2952 if (!data)
2953 goto err_clk_disable_unprepare;
2954 atmel_port->rx_ring.buf = data;
2955 }
2956
2957 rs485_enabled = atmel_port->uart.rs485.flags & SER_RS485_ENABLED;
2958
2959 ret = uart_add_one_port(&atmel_uart, &atmel_port->uart);
2960 if (ret)
2961 goto err_add_port;
2962
2963 device_init_wakeup(&pdev->dev, 1);
2964 platform_set_drvdata(pdev, atmel_port);
2965
2966 if (rs485_enabled) {
2967 atmel_uart_writel(&atmel_port->uart, ATMEL_US_MR,
2968 ATMEL_US_USMODE_NORMAL);
2969 atmel_uart_writel(&atmel_port->uart, ATMEL_US_CR,
2970 ATMEL_US_RTSEN);
2971 }
2972
2973 /*
2974 * Get port name of usart or uart
2975 */
2976 atmel_get_ip_name(&atmel_port->uart);
2977
2978 /*
2979 * The peripheral clock can now safely be disabled till the port
2980 * is used
2981 */
2982 clk_disable_unprepare(atmel_port->clk);
2983
2984 return 0;
2985
2986err_add_port:
2987 kfree(atmel_port->rx_ring.buf);
2988 atmel_port->rx_ring.buf = NULL;
2989err_clk_disable_unprepare:
2990 clk_disable_unprepare(atmel_port->clk);
2991 clear_bit(atmel_port->uart.line, atmel_ports_in_use);
2992err:
2993 return ret;
2994}
2995
2996/*
2997 * Even if the driver is not modular, it makes sense to be able to
2998 * unbind a device: there can be many bound devices, and there are
2999 * situations where dynamic binding and unbinding can be useful.
3000 *
3001 * For example, a connected device can require a specific firmware update
3002 * protocol that needs bitbanging on IO lines, but use the regular serial
3003 * port in the normal case.
3004 */
3005static int atmel_serial_remove(struct platform_device *pdev)
3006{
3007 struct uart_port *port = platform_get_drvdata(pdev);
3008 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
3009 int ret = 0;
3010
3011 tasklet_kill(&atmel_port->tasklet_rx);
3012 tasklet_kill(&atmel_port->tasklet_tx);
3013
3014 device_init_wakeup(&pdev->dev, 0);
3015
3016 ret = uart_remove_one_port(&atmel_uart, port);
3017
3018 kfree(atmel_port->rx_ring.buf);
3019
3020 /* "port" is allocated statically, so we shouldn't free it */
3021
3022 clear_bit(port->line, atmel_ports_in_use);
3023
3024 pdev->dev.of_node = NULL;
3025
3026 return ret;
3027}
3028
3029static SIMPLE_DEV_PM_OPS(atmel_serial_pm_ops, atmel_serial_suspend,
3030 atmel_serial_resume);
3031
3032static struct platform_driver atmel_serial_driver = {
3033 .probe = atmel_serial_probe,
3034 .remove = atmel_serial_remove,
3035 .driver = {
3036 .name = "atmel_usart_serial",
3037 .of_match_table = of_match_ptr(atmel_serial_dt_ids),
3038 .pm = pm_ptr(&atmel_serial_pm_ops),
3039 },
3040};
3041
3042static int __init atmel_serial_init(void)
3043{
3044 int ret;
3045
3046 ret = uart_register_driver(&atmel_uart);
3047 if (ret)
3048 return ret;
3049
3050 ret = platform_driver_register(&atmel_serial_driver);
3051 if (ret)
3052 uart_unregister_driver(&atmel_uart);
3053
3054 return ret;
3055}
3056device_initcall(atmel_serial_init);
1/*
2 * Driver for Atmel AT91 / AT32 Serial ports
3 * Copyright (C) 2003 Rick Bronson
4 *
5 * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd.
6 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
7 *
8 * DMA support added by Chip Coldwell.
9 *
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License as published by
12 * the Free Software Foundation; either version 2 of the License, or
13 * (at your option) any later version.
14 *
15 * This program is distributed in the hope that it will be useful,
16 * but WITHOUT ANY WARRANTY; without even the implied warranty of
17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
18 * GNU General Public License for more details.
19 *
20 * You should have received a copy of the GNU General Public License
21 * along with this program; if not, write to the Free Software
22 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
23 *
24 */
25#include <linux/module.h>
26#include <linux/tty.h>
27#include <linux/ioport.h>
28#include <linux/slab.h>
29#include <linux/init.h>
30#include <linux/serial.h>
31#include <linux/clk.h>
32#include <linux/console.h>
33#include <linux/sysrq.h>
34#include <linux/tty_flip.h>
35#include <linux/platform_device.h>
36#include <linux/of.h>
37#include <linux/of_device.h>
38#include <linux/dma-mapping.h>
39#include <linux/atmel_pdc.h>
40#include <linux/atmel_serial.h>
41#include <linux/uaccess.h>
42
43#include <asm/io.h>
44#include <asm/ioctls.h>
45
46#include <asm/mach/serial_at91.h>
47#include <mach/board.h>
48
49#ifdef CONFIG_ARM
50#include <mach/cpu.h>
51#include <asm/gpio.h>
52#endif
53
54#define PDC_BUFFER_SIZE 512
55/* Revisit: We should calculate this based on the actual port settings */
56#define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */
57
58#if defined(CONFIG_SERIAL_ATMEL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
59#define SUPPORT_SYSRQ
60#endif
61
62#include <linux/serial_core.h>
63
64static void atmel_start_rx(struct uart_port *port);
65static void atmel_stop_rx(struct uart_port *port);
66
67#ifdef CONFIG_SERIAL_ATMEL_TTYAT
68
69/* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we
70 * should coexist with the 8250 driver, such as if we have an external 16C550
71 * UART. */
72#define SERIAL_ATMEL_MAJOR 204
73#define MINOR_START 154
74#define ATMEL_DEVICENAME "ttyAT"
75
76#else
77
78/* Use device name ttyS, major 4, minor 64-68. This is the usual serial port
79 * name, but it is legally reserved for the 8250 driver. */
80#define SERIAL_ATMEL_MAJOR TTY_MAJOR
81#define MINOR_START 64
82#define ATMEL_DEVICENAME "ttyS"
83
84#endif
85
86#define ATMEL_ISR_PASS_LIMIT 256
87
88/* UART registers. CR is write-only, hence no GET macro */
89#define UART_PUT_CR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_CR)
90#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR)
91#define UART_PUT_MR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_MR)
92#define UART_PUT_IER(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IER)
93#define UART_PUT_IDR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IDR)
94#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR)
95#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR)
96#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR)
97#define UART_PUT_CHAR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_THR)
98#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR)
99#define UART_PUT_BRGR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR)
100#define UART_PUT_RTOR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR)
101#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR)
102
103 /* PDC registers */
104#define UART_PUT_PTCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR)
105#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR)
106
107#define UART_PUT_RPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR)
108#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR)
109#define UART_PUT_RCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR)
110#define UART_PUT_RNPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR)
111#define UART_PUT_RNCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR)
112
113#define UART_PUT_TPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR)
114#define UART_PUT_TCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR)
115#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR)
116
117static int (*atmel_open_hook)(struct uart_port *);
118static void (*atmel_close_hook)(struct uart_port *);
119
120struct atmel_dma_buffer {
121 unsigned char *buf;
122 dma_addr_t dma_addr;
123 unsigned int dma_size;
124 unsigned int ofs;
125};
126
127struct atmel_uart_char {
128 u16 status;
129 u16 ch;
130};
131
132#define ATMEL_SERIAL_RINGSIZE 1024
133
134/*
135 * We wrap our port structure around the generic uart_port.
136 */
137struct atmel_uart_port {
138 struct uart_port uart; /* uart */
139 struct clk *clk; /* uart clock */
140 int may_wakeup; /* cached value of device_may_wakeup for times we need to disable it */
141 u32 backup_imr; /* IMR saved during suspend */
142 int break_active; /* break being received */
143
144 short use_dma_rx; /* enable PDC receiver */
145 short pdc_rx_idx; /* current PDC RX buffer */
146 struct atmel_dma_buffer pdc_rx[2]; /* PDC receier */
147
148 short use_dma_tx; /* enable PDC transmitter */
149 struct atmel_dma_buffer pdc_tx; /* PDC transmitter */
150
151 struct tasklet_struct tasklet;
152 unsigned int irq_status;
153 unsigned int irq_status_prev;
154
155 struct circ_buf rx_ring;
156
157 struct serial_rs485 rs485; /* rs485 settings */
158 unsigned int tx_done_mask;
159};
160
161static struct atmel_uart_port atmel_ports[ATMEL_MAX_UART];
162static unsigned long atmel_ports_in_use;
163
164#ifdef SUPPORT_SYSRQ
165static struct console atmel_console;
166#endif
167
168#if defined(CONFIG_OF)
169static const struct of_device_id atmel_serial_dt_ids[] = {
170 { .compatible = "atmel,at91rm9200-usart" },
171 { .compatible = "atmel,at91sam9260-usart" },
172 { /* sentinel */ }
173};
174
175MODULE_DEVICE_TABLE(of, atmel_serial_dt_ids);
176#endif
177
178static inline struct atmel_uart_port *
179to_atmel_uart_port(struct uart_port *uart)
180{
181 return container_of(uart, struct atmel_uart_port, uart);
182}
183
184#ifdef CONFIG_SERIAL_ATMEL_PDC
185static bool atmel_use_dma_rx(struct uart_port *port)
186{
187 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
188
189 return atmel_port->use_dma_rx;
190}
191
192static bool atmel_use_dma_tx(struct uart_port *port)
193{
194 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
195
196 return atmel_port->use_dma_tx;
197}
198#else
199static bool atmel_use_dma_rx(struct uart_port *port)
200{
201 return false;
202}
203
204static bool atmel_use_dma_tx(struct uart_port *port)
205{
206 return false;
207}
208#endif
209
210/* Enable or disable the rs485 support */
211void atmel_config_rs485(struct uart_port *port, struct serial_rs485 *rs485conf)
212{
213 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
214 unsigned int mode;
215 unsigned long flags;
216
217 spin_lock_irqsave(&port->lock, flags);
218
219 /* Disable interrupts */
220 UART_PUT_IDR(port, atmel_port->tx_done_mask);
221
222 mode = UART_GET_MR(port);
223
224 /* Resetting serial mode to RS232 (0x0) */
225 mode &= ~ATMEL_US_USMODE;
226
227 atmel_port->rs485 = *rs485conf;
228
229 if (rs485conf->flags & SER_RS485_ENABLED) {
230 dev_dbg(port->dev, "Setting UART to RS485\n");
231 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
232 if ((rs485conf->delay_rts_after_send) > 0)
233 UART_PUT_TTGR(port, rs485conf->delay_rts_after_send);
234 mode |= ATMEL_US_USMODE_RS485;
235 } else {
236 dev_dbg(port->dev, "Setting UART to RS232\n");
237 if (atmel_use_dma_tx(port))
238 atmel_port->tx_done_mask = ATMEL_US_ENDTX |
239 ATMEL_US_TXBUFE;
240 else
241 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
242 }
243 UART_PUT_MR(port, mode);
244
245 /* Enable interrupts */
246 UART_PUT_IER(port, atmel_port->tx_done_mask);
247
248 spin_unlock_irqrestore(&port->lock, flags);
249
250}
251
252/*
253 * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty.
254 */
255static u_int atmel_tx_empty(struct uart_port *port)
256{
257 return (UART_GET_CSR(port) & ATMEL_US_TXEMPTY) ? TIOCSER_TEMT : 0;
258}
259
260/*
261 * Set state of the modem control output lines
262 */
263static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
264{
265 unsigned int control = 0;
266 unsigned int mode;
267 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
268
269#ifdef CONFIG_ARCH_AT91RM9200
270 if (cpu_is_at91rm9200()) {
271 /*
272 * AT91RM9200 Errata #39: RTS0 is not internally connected
273 * to PA21. We need to drive the pin manually.
274 */
275 if (port->mapbase == AT91RM9200_BASE_US0) {
276 if (mctrl & TIOCM_RTS)
277 at91_set_gpio_value(AT91_PIN_PA21, 0);
278 else
279 at91_set_gpio_value(AT91_PIN_PA21, 1);
280 }
281 }
282#endif
283
284 if (mctrl & TIOCM_RTS)
285 control |= ATMEL_US_RTSEN;
286 else
287 control |= ATMEL_US_RTSDIS;
288
289 if (mctrl & TIOCM_DTR)
290 control |= ATMEL_US_DTREN;
291 else
292 control |= ATMEL_US_DTRDIS;
293
294 UART_PUT_CR(port, control);
295
296 /* Local loopback mode? */
297 mode = UART_GET_MR(port) & ~ATMEL_US_CHMODE;
298 if (mctrl & TIOCM_LOOP)
299 mode |= ATMEL_US_CHMODE_LOC_LOOP;
300 else
301 mode |= ATMEL_US_CHMODE_NORMAL;
302
303 /* Resetting serial mode to RS232 (0x0) */
304 mode &= ~ATMEL_US_USMODE;
305
306 if (atmel_port->rs485.flags & SER_RS485_ENABLED) {
307 dev_dbg(port->dev, "Setting UART to RS485\n");
308 if ((atmel_port->rs485.delay_rts_after_send) > 0)
309 UART_PUT_TTGR(port,
310 atmel_port->rs485.delay_rts_after_send);
311 mode |= ATMEL_US_USMODE_RS485;
312 } else {
313 dev_dbg(port->dev, "Setting UART to RS232\n");
314 }
315 UART_PUT_MR(port, mode);
316}
317
318/*
319 * Get state of the modem control input lines
320 */
321static u_int atmel_get_mctrl(struct uart_port *port)
322{
323 unsigned int status, ret = 0;
324
325 status = UART_GET_CSR(port);
326
327 /*
328 * The control signals are active low.
329 */
330 if (!(status & ATMEL_US_DCD))
331 ret |= TIOCM_CD;
332 if (!(status & ATMEL_US_CTS))
333 ret |= TIOCM_CTS;
334 if (!(status & ATMEL_US_DSR))
335 ret |= TIOCM_DSR;
336 if (!(status & ATMEL_US_RI))
337 ret |= TIOCM_RI;
338
339 return ret;
340}
341
342/*
343 * Stop transmitting.
344 */
345static void atmel_stop_tx(struct uart_port *port)
346{
347 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
348
349 if (atmel_use_dma_tx(port)) {
350 /* disable PDC transmit */
351 UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);
352 }
353 /* Disable interrupts */
354 UART_PUT_IDR(port, atmel_port->tx_done_mask);
355
356 if ((atmel_port->rs485.flags & SER_RS485_ENABLED) &&
357 !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX))
358 atmel_start_rx(port);
359}
360
361/*
362 * Start transmitting.
363 */
364static void atmel_start_tx(struct uart_port *port)
365{
366 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
367
368 if (atmel_use_dma_tx(port)) {
369 if (UART_GET_PTSR(port) & ATMEL_PDC_TXTEN)
370 /* The transmitter is already running. Yes, we
371 really need this.*/
372 return;
373
374 if ((atmel_port->rs485.flags & SER_RS485_ENABLED) &&
375 !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX))
376 atmel_stop_rx(port);
377
378 /* re-enable PDC transmit */
379 UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);
380 }
381 /* Enable interrupts */
382 UART_PUT_IER(port, atmel_port->tx_done_mask);
383}
384
385/*
386 * start receiving - port is in process of being opened.
387 */
388static void atmel_start_rx(struct uart_port *port)
389{
390 UART_PUT_CR(port, ATMEL_US_RSTSTA); /* reset status and receiver */
391
392 UART_PUT_CR(port, ATMEL_US_RXEN);
393
394 if (atmel_use_dma_rx(port)) {
395 /* enable PDC controller */
396 UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
397 port->read_status_mask);
398 UART_PUT_PTCR(port, ATMEL_PDC_RXTEN);
399 } else {
400 UART_PUT_IER(port, ATMEL_US_RXRDY);
401 }
402}
403
404/*
405 * Stop receiving - port is in process of being closed.
406 */
407static void atmel_stop_rx(struct uart_port *port)
408{
409 UART_PUT_CR(port, ATMEL_US_RXDIS);
410
411 if (atmel_use_dma_rx(port)) {
412 /* disable PDC receive */
413 UART_PUT_PTCR(port, ATMEL_PDC_RXTDIS);
414 UART_PUT_IDR(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
415 port->read_status_mask);
416 } else {
417 UART_PUT_IDR(port, ATMEL_US_RXRDY);
418 }
419}
420
421/*
422 * Enable modem status interrupts
423 */
424static void atmel_enable_ms(struct uart_port *port)
425{
426 UART_PUT_IER(port, ATMEL_US_RIIC | ATMEL_US_DSRIC
427 | ATMEL_US_DCDIC | ATMEL_US_CTSIC);
428}
429
430/*
431 * Control the transmission of a break signal
432 */
433static void atmel_break_ctl(struct uart_port *port, int break_state)
434{
435 if (break_state != 0)
436 UART_PUT_CR(port, ATMEL_US_STTBRK); /* start break */
437 else
438 UART_PUT_CR(port, ATMEL_US_STPBRK); /* stop break */
439}
440
441/*
442 * Stores the incoming character in the ring buffer
443 */
444static void
445atmel_buffer_rx_char(struct uart_port *port, unsigned int status,
446 unsigned int ch)
447{
448 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
449 struct circ_buf *ring = &atmel_port->rx_ring;
450 struct atmel_uart_char *c;
451
452 if (!CIRC_SPACE(ring->head, ring->tail, ATMEL_SERIAL_RINGSIZE))
453 /* Buffer overflow, ignore char */
454 return;
455
456 c = &((struct atmel_uart_char *)ring->buf)[ring->head];
457 c->status = status;
458 c->ch = ch;
459
460 /* Make sure the character is stored before we update head. */
461 smp_wmb();
462
463 ring->head = (ring->head + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
464}
465
466/*
467 * Deal with parity, framing and overrun errors.
468 */
469static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status)
470{
471 /* clear error */
472 UART_PUT_CR(port, ATMEL_US_RSTSTA);
473
474 if (status & ATMEL_US_RXBRK) {
475 /* ignore side-effect */
476 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
477 port->icount.brk++;
478 }
479 if (status & ATMEL_US_PARE)
480 port->icount.parity++;
481 if (status & ATMEL_US_FRAME)
482 port->icount.frame++;
483 if (status & ATMEL_US_OVRE)
484 port->icount.overrun++;
485}
486
487/*
488 * Characters received (called from interrupt handler)
489 */
490static void atmel_rx_chars(struct uart_port *port)
491{
492 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
493 unsigned int status, ch;
494
495 status = UART_GET_CSR(port);
496 while (status & ATMEL_US_RXRDY) {
497 ch = UART_GET_CHAR(port);
498
499 /*
500 * note that the error handling code is
501 * out of the main execution path
502 */
503 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
504 | ATMEL_US_OVRE | ATMEL_US_RXBRK)
505 || atmel_port->break_active)) {
506
507 /* clear error */
508 UART_PUT_CR(port, ATMEL_US_RSTSTA);
509
510 if (status & ATMEL_US_RXBRK
511 && !atmel_port->break_active) {
512 atmel_port->break_active = 1;
513 UART_PUT_IER(port, ATMEL_US_RXBRK);
514 } else {
515 /*
516 * This is either the end-of-break
517 * condition or we've received at
518 * least one character without RXBRK
519 * being set. In both cases, the next
520 * RXBRK will indicate start-of-break.
521 */
522 UART_PUT_IDR(port, ATMEL_US_RXBRK);
523 status &= ~ATMEL_US_RXBRK;
524 atmel_port->break_active = 0;
525 }
526 }
527
528 atmel_buffer_rx_char(port, status, ch);
529 status = UART_GET_CSR(port);
530 }
531
532 tasklet_schedule(&atmel_port->tasklet);
533}
534
535/*
536 * Transmit characters (called from tasklet with TXRDY interrupt
537 * disabled)
538 */
539static void atmel_tx_chars(struct uart_port *port)
540{
541 struct circ_buf *xmit = &port->state->xmit;
542 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
543
544 if (port->x_char && UART_GET_CSR(port) & atmel_port->tx_done_mask) {
545 UART_PUT_CHAR(port, port->x_char);
546 port->icount.tx++;
547 port->x_char = 0;
548 }
549 if (uart_circ_empty(xmit) || uart_tx_stopped(port))
550 return;
551
552 while (UART_GET_CSR(port) & atmel_port->tx_done_mask) {
553 UART_PUT_CHAR(port, xmit->buf[xmit->tail]);
554 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
555 port->icount.tx++;
556 if (uart_circ_empty(xmit))
557 break;
558 }
559
560 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
561 uart_write_wakeup(port);
562
563 if (!uart_circ_empty(xmit))
564 /* Enable interrupts */
565 UART_PUT_IER(port, atmel_port->tx_done_mask);
566}
567
568/*
569 * receive interrupt handler.
570 */
571static void
572atmel_handle_receive(struct uart_port *port, unsigned int pending)
573{
574 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
575
576 if (atmel_use_dma_rx(port)) {
577 /*
578 * PDC receive. Just schedule the tasklet and let it
579 * figure out the details.
580 *
581 * TODO: We're not handling error flags correctly at
582 * the moment.
583 */
584 if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) {
585 UART_PUT_IDR(port, (ATMEL_US_ENDRX
586 | ATMEL_US_TIMEOUT));
587 tasklet_schedule(&atmel_port->tasklet);
588 }
589
590 if (pending & (ATMEL_US_RXBRK | ATMEL_US_OVRE |
591 ATMEL_US_FRAME | ATMEL_US_PARE))
592 atmel_pdc_rxerr(port, pending);
593 }
594
595 /* Interrupt receive */
596 if (pending & ATMEL_US_RXRDY)
597 atmel_rx_chars(port);
598 else if (pending & ATMEL_US_RXBRK) {
599 /*
600 * End of break detected. If it came along with a
601 * character, atmel_rx_chars will handle it.
602 */
603 UART_PUT_CR(port, ATMEL_US_RSTSTA);
604 UART_PUT_IDR(port, ATMEL_US_RXBRK);
605 atmel_port->break_active = 0;
606 }
607}
608
609/*
610 * transmit interrupt handler. (Transmit is IRQF_NODELAY safe)
611 */
612static void
613atmel_handle_transmit(struct uart_port *port, unsigned int pending)
614{
615 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
616
617 if (pending & atmel_port->tx_done_mask) {
618 /* Either PDC or interrupt transmission */
619 UART_PUT_IDR(port, atmel_port->tx_done_mask);
620 tasklet_schedule(&atmel_port->tasklet);
621 }
622}
623
624/*
625 * status flags interrupt handler.
626 */
627static void
628atmel_handle_status(struct uart_port *port, unsigned int pending,
629 unsigned int status)
630{
631 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
632
633 if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC
634 | ATMEL_US_CTSIC)) {
635 atmel_port->irq_status = status;
636 tasklet_schedule(&atmel_port->tasklet);
637 }
638}
639
640/*
641 * Interrupt handler
642 */
643static irqreturn_t atmel_interrupt(int irq, void *dev_id)
644{
645 struct uart_port *port = dev_id;
646 unsigned int status, pending, pass_counter = 0;
647
648 do {
649 status = UART_GET_CSR(port);
650 pending = status & UART_GET_IMR(port);
651 if (!pending)
652 break;
653
654 atmel_handle_receive(port, pending);
655 atmel_handle_status(port, pending, status);
656 atmel_handle_transmit(port, pending);
657 } while (pass_counter++ < ATMEL_ISR_PASS_LIMIT);
658
659 return pass_counter ? IRQ_HANDLED : IRQ_NONE;
660}
661
662/*
663 * Called from tasklet with ENDTX and TXBUFE interrupts disabled.
664 */
665static void atmel_tx_dma(struct uart_port *port)
666{
667 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
668 struct circ_buf *xmit = &port->state->xmit;
669 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
670 int count;
671
672 /* nothing left to transmit? */
673 if (UART_GET_TCR(port))
674 return;
675
676 xmit->tail += pdc->ofs;
677 xmit->tail &= UART_XMIT_SIZE - 1;
678
679 port->icount.tx += pdc->ofs;
680 pdc->ofs = 0;
681
682 /* more to transmit - setup next transfer */
683
684 /* disable PDC transmit */
685 UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);
686
687 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
688 dma_sync_single_for_device(port->dev,
689 pdc->dma_addr,
690 pdc->dma_size,
691 DMA_TO_DEVICE);
692
693 count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
694 pdc->ofs = count;
695
696 UART_PUT_TPR(port, pdc->dma_addr + xmit->tail);
697 UART_PUT_TCR(port, count);
698 /* re-enable PDC transmit */
699 UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);
700 /* Enable interrupts */
701 UART_PUT_IER(port, atmel_port->tx_done_mask);
702 } else {
703 if ((atmel_port->rs485.flags & SER_RS485_ENABLED) &&
704 !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX)) {
705 /* DMA done, stop TX, start RX for RS485 */
706 atmel_start_rx(port);
707 }
708 }
709
710 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
711 uart_write_wakeup(port);
712}
713
714static void atmel_rx_from_ring(struct uart_port *port)
715{
716 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
717 struct circ_buf *ring = &atmel_port->rx_ring;
718 unsigned int flg;
719 unsigned int status;
720
721 while (ring->head != ring->tail) {
722 struct atmel_uart_char c;
723
724 /* Make sure c is loaded after head. */
725 smp_rmb();
726
727 c = ((struct atmel_uart_char *)ring->buf)[ring->tail];
728
729 ring->tail = (ring->tail + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
730
731 port->icount.rx++;
732 status = c.status;
733 flg = TTY_NORMAL;
734
735 /*
736 * note that the error handling code is
737 * out of the main execution path
738 */
739 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
740 | ATMEL_US_OVRE | ATMEL_US_RXBRK))) {
741 if (status & ATMEL_US_RXBRK) {
742 /* ignore side-effect */
743 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
744
745 port->icount.brk++;
746 if (uart_handle_break(port))
747 continue;
748 }
749 if (status & ATMEL_US_PARE)
750 port->icount.parity++;
751 if (status & ATMEL_US_FRAME)
752 port->icount.frame++;
753 if (status & ATMEL_US_OVRE)
754 port->icount.overrun++;
755
756 status &= port->read_status_mask;
757
758 if (status & ATMEL_US_RXBRK)
759 flg = TTY_BREAK;
760 else if (status & ATMEL_US_PARE)
761 flg = TTY_PARITY;
762 else if (status & ATMEL_US_FRAME)
763 flg = TTY_FRAME;
764 }
765
766
767 if (uart_handle_sysrq_char(port, c.ch))
768 continue;
769
770 uart_insert_char(port, status, ATMEL_US_OVRE, c.ch, flg);
771 }
772
773 /*
774 * Drop the lock here since it might end up calling
775 * uart_start(), which takes the lock.
776 */
777 spin_unlock(&port->lock);
778 tty_flip_buffer_push(port->state->port.tty);
779 spin_lock(&port->lock);
780}
781
782static void atmel_rx_from_dma(struct uart_port *port)
783{
784 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
785 struct tty_struct *tty = port->state->port.tty;
786 struct atmel_dma_buffer *pdc;
787 int rx_idx = atmel_port->pdc_rx_idx;
788 unsigned int head;
789 unsigned int tail;
790 unsigned int count;
791
792 do {
793 /* Reset the UART timeout early so that we don't miss one */
794 UART_PUT_CR(port, ATMEL_US_STTTO);
795
796 pdc = &atmel_port->pdc_rx[rx_idx];
797 head = UART_GET_RPR(port) - pdc->dma_addr;
798 tail = pdc->ofs;
799
800 /* If the PDC has switched buffers, RPR won't contain
801 * any address within the current buffer. Since head
802 * is unsigned, we just need a one-way comparison to
803 * find out.
804 *
805 * In this case, we just need to consume the entire
806 * buffer and resubmit it for DMA. This will clear the
807 * ENDRX bit as well, so that we can safely re-enable
808 * all interrupts below.
809 */
810 head = min(head, pdc->dma_size);
811
812 if (likely(head != tail)) {
813 dma_sync_single_for_cpu(port->dev, pdc->dma_addr,
814 pdc->dma_size, DMA_FROM_DEVICE);
815
816 /*
817 * head will only wrap around when we recycle
818 * the DMA buffer, and when that happens, we
819 * explicitly set tail to 0. So head will
820 * always be greater than tail.
821 */
822 count = head - tail;
823
824 tty_insert_flip_string(tty, pdc->buf + pdc->ofs, count);
825
826 dma_sync_single_for_device(port->dev, pdc->dma_addr,
827 pdc->dma_size, DMA_FROM_DEVICE);
828
829 port->icount.rx += count;
830 pdc->ofs = head;
831 }
832
833 /*
834 * If the current buffer is full, we need to check if
835 * the next one contains any additional data.
836 */
837 if (head >= pdc->dma_size) {
838 pdc->ofs = 0;
839 UART_PUT_RNPR(port, pdc->dma_addr);
840 UART_PUT_RNCR(port, pdc->dma_size);
841
842 rx_idx = !rx_idx;
843 atmel_port->pdc_rx_idx = rx_idx;
844 }
845 } while (head >= pdc->dma_size);
846
847 /*
848 * Drop the lock here since it might end up calling
849 * uart_start(), which takes the lock.
850 */
851 spin_unlock(&port->lock);
852 tty_flip_buffer_push(tty);
853 spin_lock(&port->lock);
854
855 UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
856}
857
858/*
859 * tasklet handling tty stuff outside the interrupt handler.
860 */
861static void atmel_tasklet_func(unsigned long data)
862{
863 struct uart_port *port = (struct uart_port *)data;
864 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
865 unsigned int status;
866 unsigned int status_change;
867
868 /* The interrupt handler does not take the lock */
869 spin_lock(&port->lock);
870
871 if (atmel_use_dma_tx(port))
872 atmel_tx_dma(port);
873 else
874 atmel_tx_chars(port);
875
876 status = atmel_port->irq_status;
877 status_change = status ^ atmel_port->irq_status_prev;
878
879 if (status_change & (ATMEL_US_RI | ATMEL_US_DSR
880 | ATMEL_US_DCD | ATMEL_US_CTS)) {
881 /* TODO: All reads to CSR will clear these interrupts! */
882 if (status_change & ATMEL_US_RI)
883 port->icount.rng++;
884 if (status_change & ATMEL_US_DSR)
885 port->icount.dsr++;
886 if (status_change & ATMEL_US_DCD)
887 uart_handle_dcd_change(port, !(status & ATMEL_US_DCD));
888 if (status_change & ATMEL_US_CTS)
889 uart_handle_cts_change(port, !(status & ATMEL_US_CTS));
890
891 wake_up_interruptible(&port->state->port.delta_msr_wait);
892
893 atmel_port->irq_status_prev = status;
894 }
895
896 if (atmel_use_dma_rx(port))
897 atmel_rx_from_dma(port);
898 else
899 atmel_rx_from_ring(port);
900
901 spin_unlock(&port->lock);
902}
903
904/*
905 * Perform initialization and enable port for reception
906 */
907static int atmel_startup(struct uart_port *port)
908{
909 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
910 struct tty_struct *tty = port->state->port.tty;
911 int retval;
912
913 /*
914 * Ensure that no interrupts are enabled otherwise when
915 * request_irq() is called we could get stuck trying to
916 * handle an unexpected interrupt
917 */
918 UART_PUT_IDR(port, -1);
919
920 /*
921 * Allocate the IRQ
922 */
923 retval = request_irq(port->irq, atmel_interrupt, IRQF_SHARED,
924 tty ? tty->name : "atmel_serial", port);
925 if (retval) {
926 printk("atmel_serial: atmel_startup - Can't get irq\n");
927 return retval;
928 }
929
930 /*
931 * Initialize DMA (if necessary)
932 */
933 if (atmel_use_dma_rx(port)) {
934 int i;
935
936 for (i = 0; i < 2; i++) {
937 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
938
939 pdc->buf = kmalloc(PDC_BUFFER_SIZE, GFP_KERNEL);
940 if (pdc->buf == NULL) {
941 if (i != 0) {
942 dma_unmap_single(port->dev,
943 atmel_port->pdc_rx[0].dma_addr,
944 PDC_BUFFER_SIZE,
945 DMA_FROM_DEVICE);
946 kfree(atmel_port->pdc_rx[0].buf);
947 }
948 free_irq(port->irq, port);
949 return -ENOMEM;
950 }
951 pdc->dma_addr = dma_map_single(port->dev,
952 pdc->buf,
953 PDC_BUFFER_SIZE,
954 DMA_FROM_DEVICE);
955 pdc->dma_size = PDC_BUFFER_SIZE;
956 pdc->ofs = 0;
957 }
958
959 atmel_port->pdc_rx_idx = 0;
960
961 UART_PUT_RPR(port, atmel_port->pdc_rx[0].dma_addr);
962 UART_PUT_RCR(port, PDC_BUFFER_SIZE);
963
964 UART_PUT_RNPR(port, atmel_port->pdc_rx[1].dma_addr);
965 UART_PUT_RNCR(port, PDC_BUFFER_SIZE);
966 }
967 if (atmel_use_dma_tx(port)) {
968 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
969 struct circ_buf *xmit = &port->state->xmit;
970
971 pdc->buf = xmit->buf;
972 pdc->dma_addr = dma_map_single(port->dev,
973 pdc->buf,
974 UART_XMIT_SIZE,
975 DMA_TO_DEVICE);
976 pdc->dma_size = UART_XMIT_SIZE;
977 pdc->ofs = 0;
978 }
979
980 /*
981 * If there is a specific "open" function (to register
982 * control line interrupts)
983 */
984 if (atmel_open_hook) {
985 retval = atmel_open_hook(port);
986 if (retval) {
987 free_irq(port->irq, port);
988 return retval;
989 }
990 }
991
992 /* Save current CSR for comparison in atmel_tasklet_func() */
993 atmel_port->irq_status_prev = UART_GET_CSR(port);
994 atmel_port->irq_status = atmel_port->irq_status_prev;
995
996 /*
997 * Finally, enable the serial port
998 */
999 UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
1000 /* enable xmit & rcvr */
1001 UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
1002
1003 if (atmel_use_dma_rx(port)) {
1004 /* set UART timeout */
1005 UART_PUT_RTOR(port, PDC_RX_TIMEOUT);
1006 UART_PUT_CR(port, ATMEL_US_STTTO);
1007
1008 UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1009 /* enable PDC controller */
1010 UART_PUT_PTCR(port, ATMEL_PDC_RXTEN);
1011 } else {
1012 /* enable receive only */
1013 UART_PUT_IER(port, ATMEL_US_RXRDY);
1014 }
1015
1016 return 0;
1017}
1018
1019/*
1020 * Disable the port
1021 */
1022static void atmel_shutdown(struct uart_port *port)
1023{
1024 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1025 /*
1026 * Ensure everything is stopped.
1027 */
1028 atmel_stop_rx(port);
1029 atmel_stop_tx(port);
1030
1031 /*
1032 * Shut-down the DMA.
1033 */
1034 if (atmel_use_dma_rx(port)) {
1035 int i;
1036
1037 for (i = 0; i < 2; i++) {
1038 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1039
1040 dma_unmap_single(port->dev,
1041 pdc->dma_addr,
1042 pdc->dma_size,
1043 DMA_FROM_DEVICE);
1044 kfree(pdc->buf);
1045 }
1046 }
1047 if (atmel_use_dma_tx(port)) {
1048 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1049
1050 dma_unmap_single(port->dev,
1051 pdc->dma_addr,
1052 pdc->dma_size,
1053 DMA_TO_DEVICE);
1054 }
1055
1056 /*
1057 * Disable all interrupts, port and break condition.
1058 */
1059 UART_PUT_CR(port, ATMEL_US_RSTSTA);
1060 UART_PUT_IDR(port, -1);
1061
1062 /*
1063 * Free the interrupt
1064 */
1065 free_irq(port->irq, port);
1066
1067 /*
1068 * If there is a specific "close" function (to unregister
1069 * control line interrupts)
1070 */
1071 if (atmel_close_hook)
1072 atmel_close_hook(port);
1073}
1074
1075/*
1076 * Flush any TX data submitted for DMA. Called when the TX circular
1077 * buffer is reset.
1078 */
1079static void atmel_flush_buffer(struct uart_port *port)
1080{
1081 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1082
1083 if (atmel_use_dma_tx(port)) {
1084 UART_PUT_TCR(port, 0);
1085 atmel_port->pdc_tx.ofs = 0;
1086 }
1087}
1088
1089/*
1090 * Power / Clock management.
1091 */
1092static void atmel_serial_pm(struct uart_port *port, unsigned int state,
1093 unsigned int oldstate)
1094{
1095 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1096
1097 switch (state) {
1098 case 0:
1099 /*
1100 * Enable the peripheral clock for this serial port.
1101 * This is called on uart_open() or a resume event.
1102 */
1103 clk_enable(atmel_port->clk);
1104
1105 /* re-enable interrupts if we disabled some on suspend */
1106 UART_PUT_IER(port, atmel_port->backup_imr);
1107 break;
1108 case 3:
1109 /* Back up the interrupt mask and disable all interrupts */
1110 atmel_port->backup_imr = UART_GET_IMR(port);
1111 UART_PUT_IDR(port, -1);
1112
1113 /*
1114 * Disable the peripheral clock for this serial port.
1115 * This is called on uart_close() or a suspend event.
1116 */
1117 clk_disable(atmel_port->clk);
1118 break;
1119 default:
1120 printk(KERN_ERR "atmel_serial: unknown pm %d\n", state);
1121 }
1122}
1123
1124/*
1125 * Change the port parameters
1126 */
1127static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
1128 struct ktermios *old)
1129{
1130 unsigned long flags;
1131 unsigned int mode, imr, quot, baud;
1132 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1133
1134 /* Get current mode register */
1135 mode = UART_GET_MR(port) & ~(ATMEL_US_USCLKS | ATMEL_US_CHRL
1136 | ATMEL_US_NBSTOP | ATMEL_US_PAR
1137 | ATMEL_US_USMODE);
1138
1139 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
1140 quot = uart_get_divisor(port, baud);
1141
1142 if (quot > 65535) { /* BRGR is 16-bit, so switch to slower clock */
1143 quot /= 8;
1144 mode |= ATMEL_US_USCLKS_MCK_DIV8;
1145 }
1146
1147 /* byte size */
1148 switch (termios->c_cflag & CSIZE) {
1149 case CS5:
1150 mode |= ATMEL_US_CHRL_5;
1151 break;
1152 case CS6:
1153 mode |= ATMEL_US_CHRL_6;
1154 break;
1155 case CS7:
1156 mode |= ATMEL_US_CHRL_7;
1157 break;
1158 default:
1159 mode |= ATMEL_US_CHRL_8;
1160 break;
1161 }
1162
1163 /* stop bits */
1164 if (termios->c_cflag & CSTOPB)
1165 mode |= ATMEL_US_NBSTOP_2;
1166
1167 /* parity */
1168 if (termios->c_cflag & PARENB) {
1169 /* Mark or Space parity */
1170 if (termios->c_cflag & CMSPAR) {
1171 if (termios->c_cflag & PARODD)
1172 mode |= ATMEL_US_PAR_MARK;
1173 else
1174 mode |= ATMEL_US_PAR_SPACE;
1175 } else if (termios->c_cflag & PARODD)
1176 mode |= ATMEL_US_PAR_ODD;
1177 else
1178 mode |= ATMEL_US_PAR_EVEN;
1179 } else
1180 mode |= ATMEL_US_PAR_NONE;
1181
1182 /* hardware handshake (RTS/CTS) */
1183 if (termios->c_cflag & CRTSCTS)
1184 mode |= ATMEL_US_USMODE_HWHS;
1185 else
1186 mode |= ATMEL_US_USMODE_NORMAL;
1187
1188 spin_lock_irqsave(&port->lock, flags);
1189
1190 port->read_status_mask = ATMEL_US_OVRE;
1191 if (termios->c_iflag & INPCK)
1192 port->read_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
1193 if (termios->c_iflag & (BRKINT | PARMRK))
1194 port->read_status_mask |= ATMEL_US_RXBRK;
1195
1196 if (atmel_use_dma_rx(port))
1197 /* need to enable error interrupts */
1198 UART_PUT_IER(port, port->read_status_mask);
1199
1200 /*
1201 * Characters to ignore
1202 */
1203 port->ignore_status_mask = 0;
1204 if (termios->c_iflag & IGNPAR)
1205 port->ignore_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
1206 if (termios->c_iflag & IGNBRK) {
1207 port->ignore_status_mask |= ATMEL_US_RXBRK;
1208 /*
1209 * If we're ignoring parity and break indicators,
1210 * ignore overruns too (for real raw support).
1211 */
1212 if (termios->c_iflag & IGNPAR)
1213 port->ignore_status_mask |= ATMEL_US_OVRE;
1214 }
1215 /* TODO: Ignore all characters if CREAD is set.*/
1216
1217 /* update the per-port timeout */
1218 uart_update_timeout(port, termios->c_cflag, baud);
1219
1220 /*
1221 * save/disable interrupts. The tty layer will ensure that the
1222 * transmitter is empty if requested by the caller, so there's
1223 * no need to wait for it here.
1224 */
1225 imr = UART_GET_IMR(port);
1226 UART_PUT_IDR(port, -1);
1227
1228 /* disable receiver and transmitter */
1229 UART_PUT_CR(port, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
1230
1231 /* Resetting serial mode to RS232 (0x0) */
1232 mode &= ~ATMEL_US_USMODE;
1233
1234 if (atmel_port->rs485.flags & SER_RS485_ENABLED) {
1235 dev_dbg(port->dev, "Setting UART to RS485\n");
1236 if ((atmel_port->rs485.delay_rts_after_send) > 0)
1237 UART_PUT_TTGR(port,
1238 atmel_port->rs485.delay_rts_after_send);
1239 mode |= ATMEL_US_USMODE_RS485;
1240 } else {
1241 dev_dbg(port->dev, "Setting UART to RS232\n");
1242 }
1243
1244 /* set the parity, stop bits and data size */
1245 UART_PUT_MR(port, mode);
1246
1247 /* set the baud rate */
1248 UART_PUT_BRGR(port, quot);
1249 UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
1250 UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
1251
1252 /* restore interrupts */
1253 UART_PUT_IER(port, imr);
1254
1255 /* CTS flow-control and modem-status interrupts */
1256 if (UART_ENABLE_MS(port, termios->c_cflag))
1257 port->ops->enable_ms(port);
1258
1259 spin_unlock_irqrestore(&port->lock, flags);
1260}
1261
1262static void atmel_set_ldisc(struct uart_port *port, int new)
1263{
1264 if (new == N_PPS) {
1265 port->flags |= UPF_HARDPPS_CD;
1266 atmel_enable_ms(port);
1267 } else {
1268 port->flags &= ~UPF_HARDPPS_CD;
1269 }
1270}
1271
1272/*
1273 * Return string describing the specified port
1274 */
1275static const char *atmel_type(struct uart_port *port)
1276{
1277 return (port->type == PORT_ATMEL) ? "ATMEL_SERIAL" : NULL;
1278}
1279
1280/*
1281 * Release the memory region(s) being used by 'port'.
1282 */
1283static void atmel_release_port(struct uart_port *port)
1284{
1285 struct platform_device *pdev = to_platform_device(port->dev);
1286 int size = pdev->resource[0].end - pdev->resource[0].start + 1;
1287
1288 release_mem_region(port->mapbase, size);
1289
1290 if (port->flags & UPF_IOREMAP) {
1291 iounmap(port->membase);
1292 port->membase = NULL;
1293 }
1294}
1295
1296/*
1297 * Request the memory region(s) being used by 'port'.
1298 */
1299static int atmel_request_port(struct uart_port *port)
1300{
1301 struct platform_device *pdev = to_platform_device(port->dev);
1302 int size = pdev->resource[0].end - pdev->resource[0].start + 1;
1303
1304 if (!request_mem_region(port->mapbase, size, "atmel_serial"))
1305 return -EBUSY;
1306
1307 if (port->flags & UPF_IOREMAP) {
1308 port->membase = ioremap(port->mapbase, size);
1309 if (port->membase == NULL) {
1310 release_mem_region(port->mapbase, size);
1311 return -ENOMEM;
1312 }
1313 }
1314
1315 return 0;
1316}
1317
1318/*
1319 * Configure/autoconfigure the port.
1320 */
1321static void atmel_config_port(struct uart_port *port, int flags)
1322{
1323 if (flags & UART_CONFIG_TYPE) {
1324 port->type = PORT_ATMEL;
1325 atmel_request_port(port);
1326 }
1327}
1328
1329/*
1330 * Verify the new serial_struct (for TIOCSSERIAL).
1331 */
1332static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser)
1333{
1334 int ret = 0;
1335 if (ser->type != PORT_UNKNOWN && ser->type != PORT_ATMEL)
1336 ret = -EINVAL;
1337 if (port->irq != ser->irq)
1338 ret = -EINVAL;
1339 if (ser->io_type != SERIAL_IO_MEM)
1340 ret = -EINVAL;
1341 if (port->uartclk / 16 != ser->baud_base)
1342 ret = -EINVAL;
1343 if ((void *)port->mapbase != ser->iomem_base)
1344 ret = -EINVAL;
1345 if (port->iobase != ser->port)
1346 ret = -EINVAL;
1347 if (ser->hub6 != 0)
1348 ret = -EINVAL;
1349 return ret;
1350}
1351
1352#ifdef CONFIG_CONSOLE_POLL
1353static int atmel_poll_get_char(struct uart_port *port)
1354{
1355 while (!(UART_GET_CSR(port) & ATMEL_US_RXRDY))
1356 cpu_relax();
1357
1358 return UART_GET_CHAR(port);
1359}
1360
1361static void atmel_poll_put_char(struct uart_port *port, unsigned char ch)
1362{
1363 while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY))
1364 cpu_relax();
1365
1366 UART_PUT_CHAR(port, ch);
1367}
1368#endif
1369
1370static int
1371atmel_ioctl(struct uart_port *port, unsigned int cmd, unsigned long arg)
1372{
1373 struct serial_rs485 rs485conf;
1374
1375 switch (cmd) {
1376 case TIOCSRS485:
1377 if (copy_from_user(&rs485conf, (struct serial_rs485 *) arg,
1378 sizeof(rs485conf)))
1379 return -EFAULT;
1380
1381 atmel_config_rs485(port, &rs485conf);
1382 break;
1383
1384 case TIOCGRS485:
1385 if (copy_to_user((struct serial_rs485 *) arg,
1386 &(to_atmel_uart_port(port)->rs485),
1387 sizeof(rs485conf)))
1388 return -EFAULT;
1389 break;
1390
1391 default:
1392 return -ENOIOCTLCMD;
1393 }
1394 return 0;
1395}
1396
1397
1398
1399static struct uart_ops atmel_pops = {
1400 .tx_empty = atmel_tx_empty,
1401 .set_mctrl = atmel_set_mctrl,
1402 .get_mctrl = atmel_get_mctrl,
1403 .stop_tx = atmel_stop_tx,
1404 .start_tx = atmel_start_tx,
1405 .stop_rx = atmel_stop_rx,
1406 .enable_ms = atmel_enable_ms,
1407 .break_ctl = atmel_break_ctl,
1408 .startup = atmel_startup,
1409 .shutdown = atmel_shutdown,
1410 .flush_buffer = atmel_flush_buffer,
1411 .set_termios = atmel_set_termios,
1412 .set_ldisc = atmel_set_ldisc,
1413 .type = atmel_type,
1414 .release_port = atmel_release_port,
1415 .request_port = atmel_request_port,
1416 .config_port = atmel_config_port,
1417 .verify_port = atmel_verify_port,
1418 .pm = atmel_serial_pm,
1419 .ioctl = atmel_ioctl,
1420#ifdef CONFIG_CONSOLE_POLL
1421 .poll_get_char = atmel_poll_get_char,
1422 .poll_put_char = atmel_poll_put_char,
1423#endif
1424};
1425
1426static void __devinit atmel_of_init_port(struct atmel_uart_port *atmel_port,
1427 struct device_node *np)
1428{
1429 u32 rs485_delay[2];
1430
1431 /* DMA/PDC usage specification */
1432 if (of_get_property(np, "atmel,use-dma-rx", NULL))
1433 atmel_port->use_dma_rx = 1;
1434 else
1435 atmel_port->use_dma_rx = 0;
1436 if (of_get_property(np, "atmel,use-dma-tx", NULL))
1437 atmel_port->use_dma_tx = 1;
1438 else
1439 atmel_port->use_dma_tx = 0;
1440
1441 /* rs485 properties */
1442 if (of_property_read_u32_array(np, "rs485-rts-delay",
1443 rs485_delay, 2) == 0) {
1444 struct serial_rs485 *rs485conf = &atmel_port->rs485;
1445
1446 rs485conf->delay_rts_before_send = rs485_delay[0];
1447 rs485conf->delay_rts_after_send = rs485_delay[1];
1448 rs485conf->flags = 0;
1449
1450 if (of_get_property(np, "rs485-rx-during-tx", NULL))
1451 rs485conf->flags |= SER_RS485_RX_DURING_TX;
1452
1453 if (of_get_property(np, "linux,rs485-enabled-at-boot-time", NULL))
1454 rs485conf->flags |= SER_RS485_ENABLED;
1455 }
1456}
1457
1458/*
1459 * Configure the port from the platform device resource info.
1460 */
1461static void __devinit atmel_init_port(struct atmel_uart_port *atmel_port,
1462 struct platform_device *pdev)
1463{
1464 struct uart_port *port = &atmel_port->uart;
1465 struct atmel_uart_data *pdata = pdev->dev.platform_data;
1466
1467 if (pdev->dev.of_node) {
1468 atmel_of_init_port(atmel_port, pdev->dev.of_node);
1469 } else {
1470 atmel_port->use_dma_rx = pdata->use_dma_rx;
1471 atmel_port->use_dma_tx = pdata->use_dma_tx;
1472 atmel_port->rs485 = pdata->rs485;
1473 }
1474
1475 port->iotype = UPIO_MEM;
1476 port->flags = UPF_BOOT_AUTOCONF;
1477 port->ops = &atmel_pops;
1478 port->fifosize = 1;
1479 port->dev = &pdev->dev;
1480 port->mapbase = pdev->resource[0].start;
1481 port->irq = pdev->resource[1].start;
1482
1483 tasklet_init(&atmel_port->tasklet, atmel_tasklet_func,
1484 (unsigned long)port);
1485
1486 memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
1487
1488 if (pdata && pdata->regs) {
1489 /* Already mapped by setup code */
1490 port->membase = pdata->regs;
1491 } else {
1492 port->flags |= UPF_IOREMAP;
1493 port->membase = NULL;
1494 }
1495
1496 /* for console, the clock could already be configured */
1497 if (!atmel_port->clk) {
1498 atmel_port->clk = clk_get(&pdev->dev, "usart");
1499 clk_enable(atmel_port->clk);
1500 port->uartclk = clk_get_rate(atmel_port->clk);
1501 clk_disable(atmel_port->clk);
1502 /* only enable clock when USART is in use */
1503 }
1504
1505 /* Use TXEMPTY for interrupt when rs485 else TXRDY or ENDTX|TXBUFE */
1506 if (atmel_port->rs485.flags & SER_RS485_ENABLED)
1507 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
1508 else if (atmel_use_dma_tx(port)) {
1509 port->fifosize = PDC_BUFFER_SIZE;
1510 atmel_port->tx_done_mask = ATMEL_US_ENDTX | ATMEL_US_TXBUFE;
1511 } else {
1512 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
1513 }
1514}
1515
1516/*
1517 * Register board-specific modem-control line handlers.
1518 */
1519void __init atmel_register_uart_fns(struct atmel_port_fns *fns)
1520{
1521 if (fns->enable_ms)
1522 atmel_pops.enable_ms = fns->enable_ms;
1523 if (fns->get_mctrl)
1524 atmel_pops.get_mctrl = fns->get_mctrl;
1525 if (fns->set_mctrl)
1526 atmel_pops.set_mctrl = fns->set_mctrl;
1527 atmel_open_hook = fns->open;
1528 atmel_close_hook = fns->close;
1529 atmel_pops.pm = fns->pm;
1530 atmel_pops.set_wake = fns->set_wake;
1531}
1532
1533struct platform_device *atmel_default_console_device; /* the serial console device */
1534
1535#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
1536static void atmel_console_putchar(struct uart_port *port, int ch)
1537{
1538 while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY))
1539 cpu_relax();
1540 UART_PUT_CHAR(port, ch);
1541}
1542
1543/*
1544 * Interrupts are disabled on entering
1545 */
1546static void atmel_console_write(struct console *co, const char *s, u_int count)
1547{
1548 struct uart_port *port = &atmel_ports[co->index].uart;
1549 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1550 unsigned int status, imr;
1551 unsigned int pdc_tx;
1552
1553 /*
1554 * First, save IMR and then disable interrupts
1555 */
1556 imr = UART_GET_IMR(port);
1557 UART_PUT_IDR(port, ATMEL_US_RXRDY | atmel_port->tx_done_mask);
1558
1559 /* Store PDC transmit status and disable it */
1560 pdc_tx = UART_GET_PTSR(port) & ATMEL_PDC_TXTEN;
1561 UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);
1562
1563 uart_console_write(port, s, count, atmel_console_putchar);
1564
1565 /*
1566 * Finally, wait for transmitter to become empty
1567 * and restore IMR
1568 */
1569 do {
1570 status = UART_GET_CSR(port);
1571 } while (!(status & ATMEL_US_TXRDY));
1572
1573 /* Restore PDC transmit status */
1574 if (pdc_tx)
1575 UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);
1576
1577 /* set interrupts back the way they were */
1578 UART_PUT_IER(port, imr);
1579}
1580
1581/*
1582 * If the port was already initialised (eg, by a boot loader),
1583 * try to determine the current setup.
1584 */
1585static void __init atmel_console_get_options(struct uart_port *port, int *baud,
1586 int *parity, int *bits)
1587{
1588 unsigned int mr, quot;
1589
1590 /*
1591 * If the baud rate generator isn't running, the port wasn't
1592 * initialized by the boot loader.
1593 */
1594 quot = UART_GET_BRGR(port) & ATMEL_US_CD;
1595 if (!quot)
1596 return;
1597
1598 mr = UART_GET_MR(port) & ATMEL_US_CHRL;
1599 if (mr == ATMEL_US_CHRL_8)
1600 *bits = 8;
1601 else
1602 *bits = 7;
1603
1604 mr = UART_GET_MR(port) & ATMEL_US_PAR;
1605 if (mr == ATMEL_US_PAR_EVEN)
1606 *parity = 'e';
1607 else if (mr == ATMEL_US_PAR_ODD)
1608 *parity = 'o';
1609
1610 /*
1611 * The serial core only rounds down when matching this to a
1612 * supported baud rate. Make sure we don't end up slightly
1613 * lower than one of those, as it would make us fall through
1614 * to a much lower baud rate than we really want.
1615 */
1616 *baud = port->uartclk / (16 * (quot - 1));
1617}
1618
1619static int __init atmel_console_setup(struct console *co, char *options)
1620{
1621 struct uart_port *port = &atmel_ports[co->index].uart;
1622 int baud = 115200;
1623 int bits = 8;
1624 int parity = 'n';
1625 int flow = 'n';
1626
1627 if (port->membase == NULL) {
1628 /* Port not initialized yet - delay setup */
1629 return -ENODEV;
1630 }
1631
1632 clk_enable(atmel_ports[co->index].clk);
1633
1634 UART_PUT_IDR(port, -1);
1635 UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
1636 UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
1637
1638 if (options)
1639 uart_parse_options(options, &baud, &parity, &bits, &flow);
1640 else
1641 atmel_console_get_options(port, &baud, &parity, &bits);
1642
1643 return uart_set_options(port, co, baud, parity, bits, flow);
1644}
1645
1646static struct uart_driver atmel_uart;
1647
1648static struct console atmel_console = {
1649 .name = ATMEL_DEVICENAME,
1650 .write = atmel_console_write,
1651 .device = uart_console_device,
1652 .setup = atmel_console_setup,
1653 .flags = CON_PRINTBUFFER,
1654 .index = -1,
1655 .data = &atmel_uart,
1656};
1657
1658#define ATMEL_CONSOLE_DEVICE (&atmel_console)
1659
1660/*
1661 * Early console initialization (before VM subsystem initialized).
1662 */
1663static int __init atmel_console_init(void)
1664{
1665 if (atmel_default_console_device) {
1666 struct atmel_uart_data *pdata =
1667 atmel_default_console_device->dev.platform_data;
1668 int id = pdata->num;
1669 struct atmel_uart_port *port = &atmel_ports[id];
1670
1671 port->backup_imr = 0;
1672 port->uart.line = id;
1673
1674 add_preferred_console(ATMEL_DEVICENAME, id, NULL);
1675 atmel_init_port(port, atmel_default_console_device);
1676 register_console(&atmel_console);
1677 }
1678
1679 return 0;
1680}
1681
1682console_initcall(atmel_console_init);
1683
1684/*
1685 * Late console initialization.
1686 */
1687static int __init atmel_late_console_init(void)
1688{
1689 if (atmel_default_console_device
1690 && !(atmel_console.flags & CON_ENABLED))
1691 register_console(&atmel_console);
1692
1693 return 0;
1694}
1695
1696core_initcall(atmel_late_console_init);
1697
1698static inline bool atmel_is_console_port(struct uart_port *port)
1699{
1700 return port->cons && port->cons->index == port->line;
1701}
1702
1703#else
1704#define ATMEL_CONSOLE_DEVICE NULL
1705
1706static inline bool atmel_is_console_port(struct uart_port *port)
1707{
1708 return false;
1709}
1710#endif
1711
1712static struct uart_driver atmel_uart = {
1713 .owner = THIS_MODULE,
1714 .driver_name = "atmel_serial",
1715 .dev_name = ATMEL_DEVICENAME,
1716 .major = SERIAL_ATMEL_MAJOR,
1717 .minor = MINOR_START,
1718 .nr = ATMEL_MAX_UART,
1719 .cons = ATMEL_CONSOLE_DEVICE,
1720};
1721
1722#ifdef CONFIG_PM
1723static bool atmel_serial_clk_will_stop(void)
1724{
1725#ifdef CONFIG_ARCH_AT91
1726 return at91_suspend_entering_slow_clock();
1727#else
1728 return false;
1729#endif
1730}
1731
1732static int atmel_serial_suspend(struct platform_device *pdev,
1733 pm_message_t state)
1734{
1735 struct uart_port *port = platform_get_drvdata(pdev);
1736 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1737
1738 if (atmel_is_console_port(port) && console_suspend_enabled) {
1739 /* Drain the TX shifter */
1740 while (!(UART_GET_CSR(port) & ATMEL_US_TXEMPTY))
1741 cpu_relax();
1742 }
1743
1744 /* we can not wake up if we're running on slow clock */
1745 atmel_port->may_wakeup = device_may_wakeup(&pdev->dev);
1746 if (atmel_serial_clk_will_stop())
1747 device_set_wakeup_enable(&pdev->dev, 0);
1748
1749 uart_suspend_port(&atmel_uart, port);
1750
1751 return 0;
1752}
1753
1754static int atmel_serial_resume(struct platform_device *pdev)
1755{
1756 struct uart_port *port = platform_get_drvdata(pdev);
1757 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1758
1759 uart_resume_port(&atmel_uart, port);
1760 device_set_wakeup_enable(&pdev->dev, atmel_port->may_wakeup);
1761
1762 return 0;
1763}
1764#else
1765#define atmel_serial_suspend NULL
1766#define atmel_serial_resume NULL
1767#endif
1768
1769static int __devinit atmel_serial_probe(struct platform_device *pdev)
1770{
1771 struct atmel_uart_port *port;
1772 struct device_node *np = pdev->dev.of_node;
1773 struct atmel_uart_data *pdata = pdev->dev.platform_data;
1774 void *data;
1775 int ret = -ENODEV;
1776
1777 BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
1778
1779 if (np)
1780 ret = of_alias_get_id(np, "serial");
1781 else
1782 if (pdata)
1783 ret = pdata->num;
1784
1785 if (ret < 0)
1786 /* port id not found in platform data nor device-tree aliases:
1787 * auto-enumerate it */
1788 ret = find_first_zero_bit(&atmel_ports_in_use,
1789 sizeof(atmel_ports_in_use));
1790
1791 if (ret > ATMEL_MAX_UART) {
1792 ret = -ENODEV;
1793 goto err;
1794 }
1795
1796 if (test_and_set_bit(ret, &atmel_ports_in_use)) {
1797 /* port already in use */
1798 ret = -EBUSY;
1799 goto err;
1800 }
1801
1802 port = &atmel_ports[ret];
1803 port->backup_imr = 0;
1804 port->uart.line = ret;
1805
1806 atmel_init_port(port, pdev);
1807
1808 if (!atmel_use_dma_rx(&port->uart)) {
1809 ret = -ENOMEM;
1810 data = kmalloc(sizeof(struct atmel_uart_char)
1811 * ATMEL_SERIAL_RINGSIZE, GFP_KERNEL);
1812 if (!data)
1813 goto err_alloc_ring;
1814 port->rx_ring.buf = data;
1815 }
1816
1817 ret = uart_add_one_port(&atmel_uart, &port->uart);
1818 if (ret)
1819 goto err_add_port;
1820
1821#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
1822 if (atmel_is_console_port(&port->uart)
1823 && ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) {
1824 /*
1825 * The serial core enabled the clock for us, so undo
1826 * the clk_enable() in atmel_console_setup()
1827 */
1828 clk_disable(port->clk);
1829 }
1830#endif
1831
1832 device_init_wakeup(&pdev->dev, 1);
1833 platform_set_drvdata(pdev, port);
1834
1835 if (port->rs485.flags & SER_RS485_ENABLED) {
1836 UART_PUT_MR(&port->uart, ATMEL_US_USMODE_NORMAL);
1837 UART_PUT_CR(&port->uart, ATMEL_US_RTSEN);
1838 }
1839
1840 return 0;
1841
1842err_add_port:
1843 kfree(port->rx_ring.buf);
1844 port->rx_ring.buf = NULL;
1845err_alloc_ring:
1846 if (!atmel_is_console_port(&port->uart)) {
1847 clk_put(port->clk);
1848 port->clk = NULL;
1849 }
1850err:
1851 return ret;
1852}
1853
1854static int __devexit atmel_serial_remove(struct platform_device *pdev)
1855{
1856 struct uart_port *port = platform_get_drvdata(pdev);
1857 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1858 int ret = 0;
1859
1860 device_init_wakeup(&pdev->dev, 0);
1861 platform_set_drvdata(pdev, NULL);
1862
1863 ret = uart_remove_one_port(&atmel_uart, port);
1864
1865 tasklet_kill(&atmel_port->tasklet);
1866 kfree(atmel_port->rx_ring.buf);
1867
1868 /* "port" is allocated statically, so we shouldn't free it */
1869
1870 clear_bit(port->line, &atmel_ports_in_use);
1871
1872 clk_put(atmel_port->clk);
1873
1874 return ret;
1875}
1876
1877static struct platform_driver atmel_serial_driver = {
1878 .probe = atmel_serial_probe,
1879 .remove = __devexit_p(atmel_serial_remove),
1880 .suspend = atmel_serial_suspend,
1881 .resume = atmel_serial_resume,
1882 .driver = {
1883 .name = "atmel_usart",
1884 .owner = THIS_MODULE,
1885 .of_match_table = of_match_ptr(atmel_serial_dt_ids),
1886 },
1887};
1888
1889static int __init atmel_serial_init(void)
1890{
1891 int ret;
1892
1893 ret = uart_register_driver(&atmel_uart);
1894 if (ret)
1895 return ret;
1896
1897 ret = platform_driver_register(&atmel_serial_driver);
1898 if (ret)
1899 uart_unregister_driver(&atmel_uart);
1900
1901 return ret;
1902}
1903
1904static void __exit atmel_serial_exit(void)
1905{
1906 platform_driver_unregister(&atmel_serial_driver);
1907 uart_unregister_driver(&atmel_uart);
1908}
1909
1910module_init(atmel_serial_init);
1911module_exit(atmel_serial_exit);
1912
1913MODULE_AUTHOR("Rick Bronson");
1914MODULE_DESCRIPTION("Atmel AT91 / AT32 serial port driver");
1915MODULE_LICENSE("GPL");
1916MODULE_ALIAS("platform:atmel_usart");