1// SPDX-License-Identifier: GPL-2.0
  2/dts-v1/;
  3
  4#include "dove.dtsi"
  5
  6/ {
  7	model = "Globalscale D3Plug";
  8	compatible = "globalscale,d3plug", "marvell,dove";
  9
 10	memory {
 11		device_type = "memory";
 12		reg = <0x00000000 0x40000000>;
 13	};
 14
 15	chosen {
 16		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p2 rw rootwait";
 17	};
 18
 19	leds {
 20		compatible = "gpio-leds";
 21		pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>;
 22		pinctrl-names = "default";
 23
 24		wlan-act {
 25			label = "wlan-act";
 26			gpios = <&gpio0 0 1>;
 27		};
 28
 29		wlan-ap {
 30			label = "wlan-ap";
 31			gpios = <&gpio0 1 1>;
 32		};
 33
 34		status {
 35			label = "status";
 36			gpios = <&gpio0 2 1>;
 37		};
 38	};
 39
 40	regulators {
 41		compatible = "simple-bus";
 42		#address-cells = <1>;
 43		#size-cells = <0>;
 44
 45		usb_power: regulator@1 {
 46			compatible = "regulator-fixed";
 47			reg = <1>;
 48			regulator-name = "USB Power";
 49			regulator-min-microvolt = <5000000>;
 50			regulator-max-microvolt = <5000000>;
 51			enable-active-high;
 52			regulator-always-on;
 53			regulator-boot-on;
 54			gpio = <&gpio0 8 0>;
 55			pinctrl-0 = <&pmx_gpio_8>;
 56			pinctrl-names = "default";
 57		};
 58	};
 59};
 60
 61&uart0 { status = "okay"; };
 62&sata0 { status = "okay"; };
 63&i2c0 { status = "okay"; };
 64
 65/* Samsung M8G2F eMMC */
 66&sdio0 {
 67	status = "okay";
 68	non-removable;
 69	bus-width = <4>;
 70};
 71
 72/* Marvell SD8787 WLAN/BT */
 73&sdio1 {
 74	status = "okay";
 75	non-removable;
 76};
 77
 78&spi0 {
 79	status = "okay";
 80
 81	/* spi0.0: 2M Flash Macronix MX25L1605D */
 82	flash@0 {
 83		compatible = "st,m25l1605d";
 84		spi-max-frequency = <86000000>;
 85		reg = <0>;
 86	};
 87};
 88
 89&pcie {
 90	status = "okay";
 91	/* Fresco Logic USB3.0 xHCI controller */
 92	pcie@1 {
 93		status = "okay";
 94		reset-gpios = <&gpio0 26 1>;
 95		reset-delay-us = <20000>;
 96		pinctrl-0 = <&pmx_camera_gpio>;
 97		pinctrl-names = "default";
 98	};
 99	/* Mini-PCIe slot */
100	pcie@2 {
101		status = "okay";
102		reset-gpios = <&gpio0 25 1>;
103	};
104};