Loading...
1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2/*
3 * Device Tree file for Marvell Armada 370 evaluation board
4 * (DB-88F6710-BP-DDR3)
5 *
6 * Copyright (C) 2012 Marvell
7 *
8 * Lior Amsalem <alior@marvell.com>
9 * Gregory CLEMENT <gregory.clement@free-electrons.com>
10 * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
11 *
12 * Note: this Device Tree assumes that the bootloader has remapped the
13 * internal registers to 0xf1000000 (instead of the default
14 * 0xd0000000). The 0xf1000000 is the default used by the recent,
15 * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
16 * boards were delivered with an older version of the bootloader that
17 * left internal registers mapped at 0xd0000000. If you are in this
18 * situation, you should either update your bootloader (preferred
19 * solution) or the below Device Tree should be adjusted.
20 */
21
22/dts-v1/;
23#include "armada-370.dtsi"
24
25/ {
26 model = "Marvell Armada 370 Evaluation Board";
27 compatible = "marvell,a370-db", "marvell,armada370", "marvell,armada-370-xp";
28
29 chosen {
30 stdout-path = "serial0:115200n8";
31 };
32
33 memory@0 {
34 device_type = "memory";
35 reg = <0x00000000 0x40000000>; /* 1 GB */
36 };
37
38 soc {
39 ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
40 MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
41 MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
42
43 internal-regs {
44 serial@12000 {
45 status = "okay";
46 };
47 sata@a0000 {
48 nr-ports = <2>;
49 status = "okay";
50 };
51
52 ethernet@70000 {
53 pinctrl-0 = <&ge0_rgmii_pins>;
54 pinctrl-names = "default";
55 status = "okay";
56 phy = <&phy0>;
57 phy-mode = "rgmii-id";
58 };
59 ethernet@74000 {
60 pinctrl-0 = <&ge1_rgmii_pins>;
61 pinctrl-names = "default";
62 status = "okay";
63 phy = <&phy1>;
64 phy-mode = "rgmii-id";
65 };
66
67 i2c@11000 {
68 pinctrl-0 = <&i2c0_pins>;
69 pinctrl-names = "default";
70 clock-frequency = <100000>;
71 status = "okay";
72 audio_codec: audio-codec@4a {
73 #sound-dai-cells = <0>;
74 compatible = "cirrus,cs42l51";
75 reg = <0x4a>;
76 };
77 };
78
79 audio-controller@30000 {
80 pinctrl-0 = <&i2s_pins2>;
81 pinctrl-names = "default";
82 status = "okay";
83 };
84
85 mvsdio@d4000 {
86 pinctrl-0 = <&sdio_pins1>;
87 pinctrl-names = "default";
88 /*
89 * This device is disabled by default, because
90 * using the SD card connector requires
91 * changing the default CON40 connector
92 * "DB-88F6710_MPP_2xRGMII_DEVICE_Jumper" to a
93 * different connector
94 * "DB-88F6710_MPP_RGMII_SD_Jumper".
95 */
96 status = "disabled";
97 /* No CD or WP GPIOs */
98 broken-cd;
99 };
100
101 usb@50000 {
102 status = "okay";
103 };
104
105 usb@51000 {
106 status = "okay";
107 };
108 };
109 };
110
111 sound {
112 compatible = "simple-audio-card";
113 simple-audio-card,name = "Armada 370 DB Audio";
114 simple-audio-card,mclk-fs = <256>;
115 simple-audio-card,widgets =
116 "Headphone", "Out Jack",
117 "Line", "In Jack";
118 simple-audio-card,routing =
119 "Out Jack", "HPL",
120 "Out Jack", "HPR",
121 "AIN1L", "In Jack",
122 "AIN1L", "In Jack";
123 status = "okay";
124
125 simple-audio-card,dai-link@0 {
126 format = "i2s";
127 cpu {
128 sound-dai = <&audio_controller 0>;
129 };
130
131 codec {
132 sound-dai = <&audio_codec>;
133 };
134 };
135
136 simple-audio-card,dai-link@1 {
137 format = "i2s";
138 cpu {
139 sound-dai = <&audio_controller 1>;
140 };
141
142 codec {
143 sound-dai = <&spdif_out>;
144 };
145 };
146
147 simple-audio-card,dai-link@2 {
148 format = "i2s";
149 cpu {
150 sound-dai = <&audio_controller 1>;
151 };
152
153 codec {
154 sound-dai = <&spdif_in>;
155 };
156 };
157 };
158
159 spdif_out: spdif-out {
160 #sound-dai-cells = <0>;
161 compatible = "linux,spdif-dit";
162 };
163
164 spdif_in: spdif-in {
165 #sound-dai-cells = <0>;
166 compatible = "linux,spdif-dir";
167 };
168};
169
170&pciec {
171 status = "okay";
172 /*
173 * The two PCIe units are accessible through
174 * both standard PCIe slots and mini-PCIe
175 * slots on the board.
176 */
177 pcie@1,0 {
178 /* Port 0, Lane 0 */
179 status = "okay";
180 };
181
182 pcie@2,0 {
183 /* Port 1, Lane 0 */
184 status = "okay";
185 };
186};
187
188&mdio {
189 pinctrl-0 = <&mdio_pins>;
190 pinctrl-names = "default";
191 phy0: ethernet-phy@0 {
192 reg = <0>;
193 };
194
195 phy1: ethernet-phy@1 {
196 reg = <1>;
197 };
198};
199
200
201&spi0 {
202 pinctrl-0 = <&spi0_pins2>;
203 pinctrl-names = "default";
204 status = "okay";
205
206 flash@0 {
207 #address-cells = <1>;
208 #size-cells = <1>;
209 compatible = "mx25l25635e", "jedec,spi-nor";
210 reg = <0>; /* Chip select 0 */
211 spi-max-frequency = <50000000>;
212 };
213};
214
215&nand_controller {
216 status = "okay";
217
218 nand@0 {
219 reg = <0>;
220 label = "pxa3xx_nand-0";
221 nand-rb = <0>;
222 marvell,nand-keep-config;
223 nand-on-flash-bbt;
224
225 partitions {
226 compatible = "fixed-partitions";
227 #address-cells = <1>;
228 #size-cells = <1>;
229
230 partition@0 {
231 label = "U-Boot";
232 reg = <0 0x800000>;
233 };
234 partition@800000 {
235 label = "Linux";
236 reg = <0x800000 0x800000>;
237 };
238 partition@1000000 {
239 label = "Filesystem";
240 reg = <0x1000000 0x3f000000>;
241 };
242 };
243 };
244};
1/*
2 * Device Tree file for Marvell Armada 370 evaluation board
3 * (DB-88F6710-BP-DDR3)
4 *
5 * Copyright (C) 2012 Marvell
6 *
7 * Lior Amsalem <alior@marvell.com>
8 * Gregory CLEMENT <gregory.clement@free-electrons.com>
9 * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
10 *
11 * This file is licensed under the terms of the GNU General Public
12 * License version 2. This program is licensed "as is" without any
13 * warranty of any kind, whether express or implied.
14 */
15
16/dts-v1/;
17#include "armada-370.dtsi"
18
19/ {
20 model = "Marvell Armada 370 Evaluation Board";
21 compatible = "marvell,a370-db", "marvell,armada370", "marvell,armada-370-xp";
22
23 chosen {
24 bootargs = "console=ttyS0,115200 earlyprintk";
25 };
26
27 memory {
28 device_type = "memory";
29 reg = <0x00000000 0x40000000>; /* 1 GB */
30 };
31
32 soc {
33 ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
34 MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
35
36 internal-regs {
37 serial@12000 {
38 clock-frequency = <200000000>;
39 status = "okay";
40 };
41 sata@a0000 {
42 nr-ports = <2>;
43 status = "okay";
44 };
45
46 mdio {
47 phy0: ethernet-phy@0 {
48 reg = <0>;
49 };
50
51 phy1: ethernet-phy@1 {
52 reg = <1>;
53 };
54 };
55
56 ethernet@70000 {
57 status = "okay";
58 phy = <&phy0>;
59 phy-mode = "rgmii-id";
60 };
61 ethernet@74000 {
62 status = "okay";
63 phy = <&phy1>;
64 phy-mode = "rgmii-id";
65 };
66
67 i2c@11000 {
68 pinctrl-0 = <&i2c0_pins>;
69 pinctrl-names = "default";
70 clock-frequency = <100000>;
71 status = "okay";
72 audio_codec: audio-codec@4a {
73 compatible = "cirrus,cs42l51";
74 reg = <0x4a>;
75 };
76 };
77
78 audio-controller@30000 {
79 pinctrl-0 = <&i2s_pins2>;
80 pinctrl-names = "default";
81 status = "okay";
82 };
83
84 mvsdio@d4000 {
85 pinctrl-0 = <&sdio_pins1>;
86 pinctrl-names = "default";
87 /*
88 * This device is disabled by default, because
89 * using the SD card connector requires
90 * changing the default CON40 connector
91 * "DB-88F6710_MPP_2xRGMII_DEVICE_Jumper" to a
92 * different connector
93 * "DB-88F6710_MPP_RGMII_SD_Jumper".
94 */
95 status = "disabled";
96 /* No CD or WP GPIOs */
97 broken-cd;
98 };
99
100 pinctrl {
101 /*
102 * These pins might be muxed as I2S by
103 * the bootloader, but it conflicts
104 * with the real I2S pins that are
105 * muxed using i2s_pins. We must mux
106 * those pins to a function other than
107 * I2S.
108 */
109 pinctrl-0 = <&hog_pins1 &hog_pins2>;
110 pinctrl-names = "default";
111
112 hog_pins1: hog-pins1 {
113 marvell,pins = "mpp6", "mpp8", "mpp10",
114 "mpp12", "mpp13";
115 marvell,function = "gpio";
116 };
117
118 hog_pins2: hog-pins2 {
119 marvell,pins = "mpp5", "mpp7", "mpp9";
120 marvell,function = "gpo";
121 };
122 };
123
124 usb@50000 {
125 status = "okay";
126 };
127
128 usb@51000 {
129 status = "okay";
130 };
131
132 spi0: spi@10600 {
133 status = "okay";
134
135 spi-flash@0 {
136 #address-cells = <1>;
137 #size-cells = <1>;
138 compatible = "mx25l25635e";
139 reg = <0>; /* Chip select 0 */
140 spi-max-frequency = <50000000>;
141 };
142 };
143 };
144
145 pcie-controller {
146 status = "okay";
147 /*
148 * The two PCIe units are accessible through
149 * both standard PCIe slots and mini-PCIe
150 * slots on the board.
151 */
152 pcie@1,0 {
153 /* Port 0, Lane 0 */
154 status = "okay";
155 };
156
157 pcie@2,0 {
158 /* Port 1, Lane 0 */
159 status = "okay";
160 };
161 };
162 };
163
164 sound {
165 compatible = "marvell,a370db-audio";
166 marvell,audio-controller = <&audio_controller>;
167 marvell,audio-codec = <&audio_codec &spdif_out &spdif_in>;
168 status = "okay";
169 };
170
171 spdif_out: spdif-out {
172 compatible = "linux,spdif-dit";
173 };
174
175 spdif_in: spdif-in {
176 compatible = "linux,spdif-dir";
177 };
178};