Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Local APIC handling, local APIC timers
4 *
5 * (c) 1999, 2000, 2009 Ingo Molnar <mingo@redhat.com>
6 *
7 * Fixes
8 * Maciej W. Rozycki : Bits for genuine 82489DX APICs;
9 * thanks to Eric Gilmore
10 * and Rolf G. Tews
11 * for testing these extensively.
12 * Maciej W. Rozycki : Various updates and fixes.
13 * Mikael Pettersson : Power Management for UP-APIC.
14 * Pavel Machek and
15 * Mikael Pettersson : PM converted to driver model.
16 */
17
18#include <linux/perf_event.h>
19#include <linux/kernel_stat.h>
20#include <linux/mc146818rtc.h>
21#include <linux/acpi_pmtmr.h>
22#include <linux/clockchips.h>
23#include <linux/interrupt.h>
24#include <linux/memblock.h>
25#include <linux/ftrace.h>
26#include <linux/ioport.h>
27#include <linux/export.h>
28#include <linux/syscore_ops.h>
29#include <linux/delay.h>
30#include <linux/timex.h>
31#include <linux/i8253.h>
32#include <linux/dmar.h>
33#include <linux/init.h>
34#include <linux/cpu.h>
35#include <linux/dmi.h>
36#include <linux/smp.h>
37#include <linux/mm.h>
38
39#include <asm/trace/irq_vectors.h>
40#include <asm/irq_remapping.h>
41#include <asm/pc-conf-reg.h>
42#include <asm/perf_event.h>
43#include <asm/x86_init.h>
44#include <linux/atomic.h>
45#include <asm/barrier.h>
46#include <asm/mpspec.h>
47#include <asm/i8259.h>
48#include <asm/proto.h>
49#include <asm/traps.h>
50#include <asm/apic.h>
51#include <asm/acpi.h>
52#include <asm/io_apic.h>
53#include <asm/desc.h>
54#include <asm/hpet.h>
55#include <asm/mtrr.h>
56#include <asm/time.h>
57#include <asm/smp.h>
58#include <asm/mce.h>
59#include <asm/tsc.h>
60#include <asm/hypervisor.h>
61#include <asm/cpu_device_id.h>
62#include <asm/intel-family.h>
63#include <asm/irq_regs.h>
64#include <asm/cpu.h>
65
66unsigned int num_processors;
67
68unsigned disabled_cpus;
69
70/* Processor that is doing the boot up */
71unsigned int boot_cpu_physical_apicid __ro_after_init = -1U;
72EXPORT_SYMBOL_GPL(boot_cpu_physical_apicid);
73
74u8 boot_cpu_apic_version __ro_after_init;
75
76/*
77 * The highest APIC ID seen during enumeration.
78 */
79static unsigned int max_physical_apicid;
80
81/*
82 * Bitmask of physically existing CPUs:
83 */
84physid_mask_t phys_cpu_present_map;
85
86/*
87 * Processor to be disabled specified by kernel parameter
88 * disable_cpu_apicid=<int>, mostly used for the kdump 2nd kernel to
89 * avoid undefined behaviour caused by sending INIT from AP to BSP.
90 */
91static unsigned int disabled_cpu_apicid __ro_after_init = BAD_APICID;
92
93/*
94 * This variable controls which CPUs receive external NMIs. By default,
95 * external NMIs are delivered only to the BSP.
96 */
97static int apic_extnmi __ro_after_init = APIC_EXTNMI_BSP;
98
99/*
100 * Hypervisor supports 15 bits of APIC ID in MSI Extended Destination ID
101 */
102static bool virt_ext_dest_id __ro_after_init;
103
104/*
105 * Map cpu index to physical APIC ID
106 */
107DEFINE_EARLY_PER_CPU_READ_MOSTLY(u16, x86_cpu_to_apicid, BAD_APICID);
108DEFINE_EARLY_PER_CPU_READ_MOSTLY(u16, x86_bios_cpu_apicid, BAD_APICID);
109DEFINE_EARLY_PER_CPU_READ_MOSTLY(u32, x86_cpu_to_acpiid, U32_MAX);
110EXPORT_EARLY_PER_CPU_SYMBOL(x86_cpu_to_apicid);
111EXPORT_EARLY_PER_CPU_SYMBOL(x86_bios_cpu_apicid);
112EXPORT_EARLY_PER_CPU_SYMBOL(x86_cpu_to_acpiid);
113
114#ifdef CONFIG_X86_32
115
116/*
117 * On x86_32, the mapping between cpu and logical apicid may vary
118 * depending on apic in use. The following early percpu variable is
119 * used for the mapping. This is where the behaviors of x86_64 and 32
120 * actually diverge. Let's keep it ugly for now.
121 */
122DEFINE_EARLY_PER_CPU_READ_MOSTLY(int, x86_cpu_to_logical_apicid, BAD_APICID);
123
124/* Local APIC was disabled by the BIOS and enabled by the kernel */
125static int enabled_via_apicbase __ro_after_init;
126
127/*
128 * Handle interrupt mode configuration register (IMCR).
129 * This register controls whether the interrupt signals
130 * that reach the BSP come from the master PIC or from the
131 * local APIC. Before entering Symmetric I/O Mode, either
132 * the BIOS or the operating system must switch out of
133 * PIC Mode by changing the IMCR.
134 */
135static inline void imcr_pic_to_apic(void)
136{
137 /* NMI and 8259 INTR go through APIC */
138 pc_conf_set(PC_CONF_MPS_IMCR, 0x01);
139}
140
141static inline void imcr_apic_to_pic(void)
142{
143 /* NMI and 8259 INTR go directly to BSP */
144 pc_conf_set(PC_CONF_MPS_IMCR, 0x00);
145}
146#endif
147
148/*
149 * Knob to control our willingness to enable the local APIC.
150 *
151 * +1=force-enable
152 */
153static int force_enable_local_apic __initdata;
154
155/*
156 * APIC command line parameters
157 */
158static int __init parse_lapic(char *arg)
159{
160 if (IS_ENABLED(CONFIG_X86_32) && !arg)
161 force_enable_local_apic = 1;
162 else if (arg && !strncmp(arg, "notscdeadline", 13))
163 setup_clear_cpu_cap(X86_FEATURE_TSC_DEADLINE_TIMER);
164 return 0;
165}
166early_param("lapic", parse_lapic);
167
168#ifdef CONFIG_X86_64
169static int apic_calibrate_pmtmr __initdata;
170static __init int setup_apicpmtimer(char *s)
171{
172 apic_calibrate_pmtmr = 1;
173 notsc_setup(NULL);
174 return 1;
175}
176__setup("apicpmtimer", setup_apicpmtimer);
177#endif
178
179unsigned long mp_lapic_addr __ro_after_init;
180int disable_apic __ro_after_init;
181/* Disable local APIC timer from the kernel commandline or via dmi quirk */
182static int disable_apic_timer __initdata;
183/* Local APIC timer works in C2 */
184int local_apic_timer_c2_ok __ro_after_init;
185EXPORT_SYMBOL_GPL(local_apic_timer_c2_ok);
186
187/*
188 * Debug level, exported for io_apic.c
189 */
190int apic_verbosity __ro_after_init;
191
192int pic_mode __ro_after_init;
193
194/* Have we found an MP table */
195int smp_found_config __ro_after_init;
196
197static struct resource lapic_resource = {
198 .name = "Local APIC",
199 .flags = IORESOURCE_MEM | IORESOURCE_BUSY,
200};
201
202unsigned int lapic_timer_period = 0;
203
204static void apic_pm_activate(void);
205
206static unsigned long apic_phys __ro_after_init;
207
208/*
209 * Get the LAPIC version
210 */
211static inline int lapic_get_version(void)
212{
213 return GET_APIC_VERSION(apic_read(APIC_LVR));
214}
215
216/*
217 * Check, if the APIC is integrated or a separate chip
218 */
219static inline int lapic_is_integrated(void)
220{
221 return APIC_INTEGRATED(lapic_get_version());
222}
223
224/*
225 * Check, whether this is a modern or a first generation APIC
226 */
227static int modern_apic(void)
228{
229 /* AMD systems use old APIC versions, so check the CPU */
230 if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD &&
231 boot_cpu_data.x86 >= 0xf)
232 return 1;
233
234 /* Hygon systems use modern APIC */
235 if (boot_cpu_data.x86_vendor == X86_VENDOR_HYGON)
236 return 1;
237
238 return lapic_get_version() >= 0x14;
239}
240
241/*
242 * right after this call apic become NOOP driven
243 * so apic->write/read doesn't do anything
244 */
245static void __init apic_disable(void)
246{
247 pr_info("APIC: switched to apic NOOP\n");
248 apic = &apic_noop;
249}
250
251void native_apic_wait_icr_idle(void)
252{
253 while (apic_read(APIC_ICR) & APIC_ICR_BUSY)
254 cpu_relax();
255}
256
257u32 native_safe_apic_wait_icr_idle(void)
258{
259 u32 send_status;
260 int timeout;
261
262 timeout = 0;
263 do {
264 send_status = apic_read(APIC_ICR) & APIC_ICR_BUSY;
265 if (!send_status)
266 break;
267 inc_irq_stat(icr_read_retry_count);
268 udelay(100);
269 } while (timeout++ < 1000);
270
271 return send_status;
272}
273
274void native_apic_icr_write(u32 low, u32 id)
275{
276 unsigned long flags;
277
278 local_irq_save(flags);
279 apic_write(APIC_ICR2, SET_XAPIC_DEST_FIELD(id));
280 apic_write(APIC_ICR, low);
281 local_irq_restore(flags);
282}
283
284u64 native_apic_icr_read(void)
285{
286 u32 icr1, icr2;
287
288 icr2 = apic_read(APIC_ICR2);
289 icr1 = apic_read(APIC_ICR);
290
291 return icr1 | ((u64)icr2 << 32);
292}
293
294#ifdef CONFIG_X86_32
295/**
296 * get_physical_broadcast - Get number of physical broadcast IDs
297 */
298int get_physical_broadcast(void)
299{
300 return modern_apic() ? 0xff : 0xf;
301}
302#endif
303
304/**
305 * lapic_get_maxlvt - get the maximum number of local vector table entries
306 */
307int lapic_get_maxlvt(void)
308{
309 /*
310 * - we always have APIC integrated on 64bit mode
311 * - 82489DXs do not report # of LVT entries
312 */
313 return lapic_is_integrated() ? GET_APIC_MAXLVT(apic_read(APIC_LVR)) : 2;
314}
315
316/*
317 * Local APIC timer
318 */
319
320/* Clock divisor */
321#define APIC_DIVISOR 16
322#define TSC_DIVISOR 8
323
324/* i82489DX specific */
325#define I82489DX_BASE_DIVIDER (((0x2) << 18))
326
327/*
328 * This function sets up the local APIC timer, with a timeout of
329 * 'clocks' APIC bus clock. During calibration we actually call
330 * this function twice on the boot CPU, once with a bogus timeout
331 * value, second time for real. The other (noncalibrating) CPUs
332 * call this function only once, with the real, calibrated value.
333 *
334 * We do reads before writes even if unnecessary, to get around the
335 * P5 APIC double write bug.
336 */
337static void __setup_APIC_LVTT(unsigned int clocks, int oneshot, int irqen)
338{
339 unsigned int lvtt_value, tmp_value;
340
341 lvtt_value = LOCAL_TIMER_VECTOR;
342 if (!oneshot)
343 lvtt_value |= APIC_LVT_TIMER_PERIODIC;
344 else if (boot_cpu_has(X86_FEATURE_TSC_DEADLINE_TIMER))
345 lvtt_value |= APIC_LVT_TIMER_TSCDEADLINE;
346
347 /*
348 * The i82489DX APIC uses bit 18 and 19 for the base divider. This
349 * overlaps with bit 18 on integrated APICs, but is not documented
350 * in the SDM. No problem though. i82489DX equipped systems do not
351 * have TSC deadline timer.
352 */
353 if (!lapic_is_integrated())
354 lvtt_value |= I82489DX_BASE_DIVIDER;
355
356 if (!irqen)
357 lvtt_value |= APIC_LVT_MASKED;
358
359 apic_write(APIC_LVTT, lvtt_value);
360
361 if (lvtt_value & APIC_LVT_TIMER_TSCDEADLINE) {
362 /*
363 * See Intel SDM: TSC-Deadline Mode chapter. In xAPIC mode,
364 * writing to the APIC LVTT and TSC_DEADLINE MSR isn't serialized.
365 * According to Intel, MFENCE can do the serialization here.
366 */
367 asm volatile("mfence" : : : "memory");
368 return;
369 }
370
371 /*
372 * Divide PICLK by 16
373 */
374 tmp_value = apic_read(APIC_TDCR);
375 apic_write(APIC_TDCR,
376 (tmp_value & ~(APIC_TDR_DIV_1 | APIC_TDR_DIV_TMBASE)) |
377 APIC_TDR_DIV_16);
378
379 if (!oneshot)
380 apic_write(APIC_TMICT, clocks / APIC_DIVISOR);
381}
382
383/*
384 * Setup extended LVT, AMD specific
385 *
386 * Software should use the LVT offsets the BIOS provides. The offsets
387 * are determined by the subsystems using it like those for MCE
388 * threshold or IBS. On K8 only offset 0 (APIC500) and MCE interrupts
389 * are supported. Beginning with family 10h at least 4 offsets are
390 * available.
391 *
392 * Since the offsets must be consistent for all cores, we keep track
393 * of the LVT offsets in software and reserve the offset for the same
394 * vector also to be used on other cores. An offset is freed by
395 * setting the entry to APIC_EILVT_MASKED.
396 *
397 * If the BIOS is right, there should be no conflicts. Otherwise a
398 * "[Firmware Bug]: ..." error message is generated. However, if
399 * software does not properly determines the offsets, it is not
400 * necessarily a BIOS bug.
401 */
402
403static atomic_t eilvt_offsets[APIC_EILVT_NR_MAX];
404
405static inline int eilvt_entry_is_changeable(unsigned int old, unsigned int new)
406{
407 return (old & APIC_EILVT_MASKED)
408 || (new == APIC_EILVT_MASKED)
409 || ((new & ~APIC_EILVT_MASKED) == old);
410}
411
412static unsigned int reserve_eilvt_offset(int offset, unsigned int new)
413{
414 unsigned int rsvd, vector;
415
416 if (offset >= APIC_EILVT_NR_MAX)
417 return ~0;
418
419 rsvd = atomic_read(&eilvt_offsets[offset]);
420 do {
421 vector = rsvd & ~APIC_EILVT_MASKED; /* 0: unassigned */
422 if (vector && !eilvt_entry_is_changeable(vector, new))
423 /* may not change if vectors are different */
424 return rsvd;
425 rsvd = atomic_cmpxchg(&eilvt_offsets[offset], rsvd, new);
426 } while (rsvd != new);
427
428 rsvd &= ~APIC_EILVT_MASKED;
429 if (rsvd && rsvd != vector)
430 pr_info("LVT offset %d assigned for vector 0x%02x\n",
431 offset, rsvd);
432
433 return new;
434}
435
436/*
437 * If mask=1, the LVT entry does not generate interrupts while mask=0
438 * enables the vector. See also the BKDGs. Must be called with
439 * preemption disabled.
440 */
441
442int setup_APIC_eilvt(u8 offset, u8 vector, u8 msg_type, u8 mask)
443{
444 unsigned long reg = APIC_EILVTn(offset);
445 unsigned int new, old, reserved;
446
447 new = (mask << 16) | (msg_type << 8) | vector;
448 old = apic_read(reg);
449 reserved = reserve_eilvt_offset(offset, new);
450
451 if (reserved != new) {
452 pr_err(FW_BUG "cpu %d, try to use APIC%lX (LVT offset %d) for "
453 "vector 0x%x, but the register is already in use for "
454 "vector 0x%x on another cpu\n",
455 smp_processor_id(), reg, offset, new, reserved);
456 return -EINVAL;
457 }
458
459 if (!eilvt_entry_is_changeable(old, new)) {
460 pr_err(FW_BUG "cpu %d, try to use APIC%lX (LVT offset %d) for "
461 "vector 0x%x, but the register is already in use for "
462 "vector 0x%x on this cpu\n",
463 smp_processor_id(), reg, offset, new, old);
464 return -EBUSY;
465 }
466
467 apic_write(reg, new);
468
469 return 0;
470}
471EXPORT_SYMBOL_GPL(setup_APIC_eilvt);
472
473/*
474 * Program the next event, relative to now
475 */
476static int lapic_next_event(unsigned long delta,
477 struct clock_event_device *evt)
478{
479 apic_write(APIC_TMICT, delta);
480 return 0;
481}
482
483static int lapic_next_deadline(unsigned long delta,
484 struct clock_event_device *evt)
485{
486 u64 tsc;
487
488 /* This MSR is special and need a special fence: */
489 weak_wrmsr_fence();
490
491 tsc = rdtsc();
492 wrmsrl(MSR_IA32_TSC_DEADLINE, tsc + (((u64) delta) * TSC_DIVISOR));
493 return 0;
494}
495
496static int lapic_timer_shutdown(struct clock_event_device *evt)
497{
498 unsigned int v;
499
500 /* Lapic used as dummy for broadcast ? */
501 if (evt->features & CLOCK_EVT_FEAT_DUMMY)
502 return 0;
503
504 v = apic_read(APIC_LVTT);
505 v |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR);
506 apic_write(APIC_LVTT, v);
507 apic_write(APIC_TMICT, 0);
508 return 0;
509}
510
511static inline int
512lapic_timer_set_periodic_oneshot(struct clock_event_device *evt, bool oneshot)
513{
514 /* Lapic used as dummy for broadcast ? */
515 if (evt->features & CLOCK_EVT_FEAT_DUMMY)
516 return 0;
517
518 __setup_APIC_LVTT(lapic_timer_period, oneshot, 1);
519 return 0;
520}
521
522static int lapic_timer_set_periodic(struct clock_event_device *evt)
523{
524 return lapic_timer_set_periodic_oneshot(evt, false);
525}
526
527static int lapic_timer_set_oneshot(struct clock_event_device *evt)
528{
529 return lapic_timer_set_periodic_oneshot(evt, true);
530}
531
532/*
533 * Local APIC timer broadcast function
534 */
535static void lapic_timer_broadcast(const struct cpumask *mask)
536{
537#ifdef CONFIG_SMP
538 apic->send_IPI_mask(mask, LOCAL_TIMER_VECTOR);
539#endif
540}
541
542
543/*
544 * The local apic timer can be used for any function which is CPU local.
545 */
546static struct clock_event_device lapic_clockevent = {
547 .name = "lapic",
548 .features = CLOCK_EVT_FEAT_PERIODIC |
549 CLOCK_EVT_FEAT_ONESHOT | CLOCK_EVT_FEAT_C3STOP
550 | CLOCK_EVT_FEAT_DUMMY,
551 .shift = 32,
552 .set_state_shutdown = lapic_timer_shutdown,
553 .set_state_periodic = lapic_timer_set_periodic,
554 .set_state_oneshot = lapic_timer_set_oneshot,
555 .set_state_oneshot_stopped = lapic_timer_shutdown,
556 .set_next_event = lapic_next_event,
557 .broadcast = lapic_timer_broadcast,
558 .rating = 100,
559 .irq = -1,
560};
561static DEFINE_PER_CPU(struct clock_event_device, lapic_events);
562
563static const struct x86_cpu_id deadline_match[] __initconst = {
564 X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS(HASWELL_X, X86_STEPPINGS(0x2, 0x2), 0x3a), /* EP */
565 X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS(HASWELL_X, X86_STEPPINGS(0x4, 0x4), 0x0f), /* EX */
566
567 X86_MATCH_INTEL_FAM6_MODEL( BROADWELL_X, 0x0b000020),
568
569 X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS(BROADWELL_D, X86_STEPPINGS(0x2, 0x2), 0x00000011),
570 X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS(BROADWELL_D, X86_STEPPINGS(0x3, 0x3), 0x0700000e),
571 X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS(BROADWELL_D, X86_STEPPINGS(0x4, 0x4), 0x0f00000c),
572 X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS(BROADWELL_D, X86_STEPPINGS(0x5, 0x5), 0x0e000003),
573
574 X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS(SKYLAKE_X, X86_STEPPINGS(0x3, 0x3), 0x01000136),
575 X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS(SKYLAKE_X, X86_STEPPINGS(0x4, 0x4), 0x02000014),
576 X86_MATCH_INTEL_FAM6_MODEL_STEPPINGS(SKYLAKE_X, X86_STEPPINGS(0x5, 0xf), 0),
577
578 X86_MATCH_INTEL_FAM6_MODEL( HASWELL, 0x22),
579 X86_MATCH_INTEL_FAM6_MODEL( HASWELL_L, 0x20),
580 X86_MATCH_INTEL_FAM6_MODEL( HASWELL_G, 0x17),
581
582 X86_MATCH_INTEL_FAM6_MODEL( BROADWELL, 0x25),
583 X86_MATCH_INTEL_FAM6_MODEL( BROADWELL_G, 0x17),
584
585 X86_MATCH_INTEL_FAM6_MODEL( SKYLAKE_L, 0xb2),
586 X86_MATCH_INTEL_FAM6_MODEL( SKYLAKE, 0xb2),
587
588 X86_MATCH_INTEL_FAM6_MODEL( KABYLAKE_L, 0x52),
589 X86_MATCH_INTEL_FAM6_MODEL( KABYLAKE, 0x52),
590
591 {},
592};
593
594static __init bool apic_validate_deadline_timer(void)
595{
596 const struct x86_cpu_id *m;
597 u32 rev;
598
599 if (!boot_cpu_has(X86_FEATURE_TSC_DEADLINE_TIMER))
600 return false;
601 if (boot_cpu_has(X86_FEATURE_HYPERVISOR))
602 return true;
603
604 m = x86_match_cpu(deadline_match);
605 if (!m)
606 return true;
607
608 rev = (u32)m->driver_data;
609
610 if (boot_cpu_data.microcode >= rev)
611 return true;
612
613 setup_clear_cpu_cap(X86_FEATURE_TSC_DEADLINE_TIMER);
614 pr_err(FW_BUG "TSC_DEADLINE disabled due to Errata; "
615 "please update microcode to version: 0x%x (or later)\n", rev);
616 return false;
617}
618
619/*
620 * Setup the local APIC timer for this CPU. Copy the initialized values
621 * of the boot CPU and register the clock event in the framework.
622 */
623static void setup_APIC_timer(void)
624{
625 struct clock_event_device *levt = this_cpu_ptr(&lapic_events);
626
627 if (this_cpu_has(X86_FEATURE_ARAT)) {
628 lapic_clockevent.features &= ~CLOCK_EVT_FEAT_C3STOP;
629 /* Make LAPIC timer preferable over percpu HPET */
630 lapic_clockevent.rating = 150;
631 }
632
633 memcpy(levt, &lapic_clockevent, sizeof(*levt));
634 levt->cpumask = cpumask_of(smp_processor_id());
635
636 if (this_cpu_has(X86_FEATURE_TSC_DEADLINE_TIMER)) {
637 levt->name = "lapic-deadline";
638 levt->features &= ~(CLOCK_EVT_FEAT_PERIODIC |
639 CLOCK_EVT_FEAT_DUMMY);
640 levt->set_next_event = lapic_next_deadline;
641 clockevents_config_and_register(levt,
642 tsc_khz * (1000 / TSC_DIVISOR),
643 0xF, ~0UL);
644 } else
645 clockevents_register_device(levt);
646}
647
648/*
649 * Install the updated TSC frequency from recalibration at the TSC
650 * deadline clockevent devices.
651 */
652static void __lapic_update_tsc_freq(void *info)
653{
654 struct clock_event_device *levt = this_cpu_ptr(&lapic_events);
655
656 if (!this_cpu_has(X86_FEATURE_TSC_DEADLINE_TIMER))
657 return;
658
659 clockevents_update_freq(levt, tsc_khz * (1000 / TSC_DIVISOR));
660}
661
662void lapic_update_tsc_freq(void)
663{
664 /*
665 * The clockevent device's ->mult and ->shift can both be
666 * changed. In order to avoid races, schedule the frequency
667 * update code on each CPU.
668 */
669 on_each_cpu(__lapic_update_tsc_freq, NULL, 0);
670}
671
672/*
673 * In this functions we calibrate APIC bus clocks to the external timer.
674 *
675 * We want to do the calibration only once since we want to have local timer
676 * irqs synchronous. CPUs connected by the same APIC bus have the very same bus
677 * frequency.
678 *
679 * This was previously done by reading the PIT/HPET and waiting for a wrap
680 * around to find out, that a tick has elapsed. I have a box, where the PIT
681 * readout is broken, so it never gets out of the wait loop again. This was
682 * also reported by others.
683 *
684 * Monitoring the jiffies value is inaccurate and the clockevents
685 * infrastructure allows us to do a simple substitution of the interrupt
686 * handler.
687 *
688 * The calibration routine also uses the pm_timer when possible, as the PIT
689 * happens to run way too slow (factor 2.3 on my VAIO CoreDuo, which goes
690 * back to normal later in the boot process).
691 */
692
693#define LAPIC_CAL_LOOPS (HZ/10)
694
695static __initdata int lapic_cal_loops = -1;
696static __initdata long lapic_cal_t1, lapic_cal_t2;
697static __initdata unsigned long long lapic_cal_tsc1, lapic_cal_tsc2;
698static __initdata unsigned long lapic_cal_pm1, lapic_cal_pm2;
699static __initdata unsigned long lapic_cal_j1, lapic_cal_j2;
700
701/*
702 * Temporary interrupt handler and polled calibration function.
703 */
704static void __init lapic_cal_handler(struct clock_event_device *dev)
705{
706 unsigned long long tsc = 0;
707 long tapic = apic_read(APIC_TMCCT);
708 unsigned long pm = acpi_pm_read_early();
709
710 if (boot_cpu_has(X86_FEATURE_TSC))
711 tsc = rdtsc();
712
713 switch (lapic_cal_loops++) {
714 case 0:
715 lapic_cal_t1 = tapic;
716 lapic_cal_tsc1 = tsc;
717 lapic_cal_pm1 = pm;
718 lapic_cal_j1 = jiffies;
719 break;
720
721 case LAPIC_CAL_LOOPS:
722 lapic_cal_t2 = tapic;
723 lapic_cal_tsc2 = tsc;
724 if (pm < lapic_cal_pm1)
725 pm += ACPI_PM_OVRRUN;
726 lapic_cal_pm2 = pm;
727 lapic_cal_j2 = jiffies;
728 break;
729 }
730}
731
732static int __init
733calibrate_by_pmtimer(long deltapm, long *delta, long *deltatsc)
734{
735 const long pm_100ms = PMTMR_TICKS_PER_SEC / 10;
736 const long pm_thresh = pm_100ms / 100;
737 unsigned long mult;
738 u64 res;
739
740#ifndef CONFIG_X86_PM_TIMER
741 return -1;
742#endif
743
744 apic_printk(APIC_VERBOSE, "... PM-Timer delta = %ld\n", deltapm);
745
746 /* Check, if the PM timer is available */
747 if (!deltapm)
748 return -1;
749
750 mult = clocksource_hz2mult(PMTMR_TICKS_PER_SEC, 22);
751
752 if (deltapm > (pm_100ms - pm_thresh) &&
753 deltapm < (pm_100ms + pm_thresh)) {
754 apic_printk(APIC_VERBOSE, "... PM-Timer result ok\n");
755 return 0;
756 }
757
758 res = (((u64)deltapm) * mult) >> 22;
759 do_div(res, 1000000);
760 pr_warn("APIC calibration not consistent "
761 "with PM-Timer: %ldms instead of 100ms\n", (long)res);
762
763 /* Correct the lapic counter value */
764 res = (((u64)(*delta)) * pm_100ms);
765 do_div(res, deltapm);
766 pr_info("APIC delta adjusted to PM-Timer: "
767 "%lu (%ld)\n", (unsigned long)res, *delta);
768 *delta = (long)res;
769
770 /* Correct the tsc counter value */
771 if (boot_cpu_has(X86_FEATURE_TSC)) {
772 res = (((u64)(*deltatsc)) * pm_100ms);
773 do_div(res, deltapm);
774 apic_printk(APIC_VERBOSE, "TSC delta adjusted to "
775 "PM-Timer: %lu (%ld)\n",
776 (unsigned long)res, *deltatsc);
777 *deltatsc = (long)res;
778 }
779
780 return 0;
781}
782
783static int __init lapic_init_clockevent(void)
784{
785 if (!lapic_timer_period)
786 return -1;
787
788 /* Calculate the scaled math multiplication factor */
789 lapic_clockevent.mult = div_sc(lapic_timer_period/APIC_DIVISOR,
790 TICK_NSEC, lapic_clockevent.shift);
791 lapic_clockevent.max_delta_ns =
792 clockevent_delta2ns(0x7FFFFFFF, &lapic_clockevent);
793 lapic_clockevent.max_delta_ticks = 0x7FFFFFFF;
794 lapic_clockevent.min_delta_ns =
795 clockevent_delta2ns(0xF, &lapic_clockevent);
796 lapic_clockevent.min_delta_ticks = 0xF;
797
798 return 0;
799}
800
801bool __init apic_needs_pit(void)
802{
803 /*
804 * If the frequencies are not known, PIT is required for both TSC
805 * and apic timer calibration.
806 */
807 if (!tsc_khz || !cpu_khz)
808 return true;
809
810 /* Is there an APIC at all or is it disabled? */
811 if (!boot_cpu_has(X86_FEATURE_APIC) || disable_apic)
812 return true;
813
814 /*
815 * If interrupt delivery mode is legacy PIC or virtual wire without
816 * configuration, the local APIC timer wont be set up. Make sure
817 * that the PIT is initialized.
818 */
819 if (apic_intr_mode == APIC_PIC ||
820 apic_intr_mode == APIC_VIRTUAL_WIRE_NO_CONFIG)
821 return true;
822
823 /* Virt guests may lack ARAT, but still have DEADLINE */
824 if (!boot_cpu_has(X86_FEATURE_ARAT))
825 return true;
826
827 /* Deadline timer is based on TSC so no further PIT action required */
828 if (boot_cpu_has(X86_FEATURE_TSC_DEADLINE_TIMER))
829 return false;
830
831 /* APIC timer disabled? */
832 if (disable_apic_timer)
833 return true;
834 /*
835 * The APIC timer frequency is known already, no PIT calibration
836 * required. If unknown, let the PIT be initialized.
837 */
838 return lapic_timer_period == 0;
839}
840
841static int __init calibrate_APIC_clock(void)
842{
843 struct clock_event_device *levt = this_cpu_ptr(&lapic_events);
844 u64 tsc_perj = 0, tsc_start = 0;
845 unsigned long jif_start;
846 unsigned long deltaj;
847 long delta, deltatsc;
848 int pm_referenced = 0;
849
850 if (boot_cpu_has(X86_FEATURE_TSC_DEADLINE_TIMER))
851 return 0;
852
853 /*
854 * Check if lapic timer has already been calibrated by platform
855 * specific routine, such as tsc calibration code. If so just fill
856 * in the clockevent structure and return.
857 */
858 if (!lapic_init_clockevent()) {
859 apic_printk(APIC_VERBOSE, "lapic timer already calibrated %d\n",
860 lapic_timer_period);
861 /*
862 * Direct calibration methods must have an always running
863 * local APIC timer, no need for broadcast timer.
864 */
865 lapic_clockevent.features &= ~CLOCK_EVT_FEAT_DUMMY;
866 return 0;
867 }
868
869 apic_printk(APIC_VERBOSE, "Using local APIC timer interrupts.\n"
870 "calibrating APIC timer ...\n");
871
872 /*
873 * There are platforms w/o global clockevent devices. Instead of
874 * making the calibration conditional on that, use a polling based
875 * approach everywhere.
876 */
877 local_irq_disable();
878
879 /*
880 * Setup the APIC counter to maximum. There is no way the lapic
881 * can underflow in the 100ms detection time frame
882 */
883 __setup_APIC_LVTT(0xffffffff, 0, 0);
884
885 /*
886 * Methods to terminate the calibration loop:
887 * 1) Global clockevent if available (jiffies)
888 * 2) TSC if available and frequency is known
889 */
890 jif_start = READ_ONCE(jiffies);
891
892 if (tsc_khz) {
893 tsc_start = rdtsc();
894 tsc_perj = div_u64((u64)tsc_khz * 1000, HZ);
895 }
896
897 /*
898 * Enable interrupts so the tick can fire, if a global
899 * clockevent device is available
900 */
901 local_irq_enable();
902
903 while (lapic_cal_loops <= LAPIC_CAL_LOOPS) {
904 /* Wait for a tick to elapse */
905 while (1) {
906 if (tsc_khz) {
907 u64 tsc_now = rdtsc();
908 if ((tsc_now - tsc_start) >= tsc_perj) {
909 tsc_start += tsc_perj;
910 break;
911 }
912 } else {
913 unsigned long jif_now = READ_ONCE(jiffies);
914
915 if (time_after(jif_now, jif_start)) {
916 jif_start = jif_now;
917 break;
918 }
919 }
920 cpu_relax();
921 }
922
923 /* Invoke the calibration routine */
924 local_irq_disable();
925 lapic_cal_handler(NULL);
926 local_irq_enable();
927 }
928
929 local_irq_disable();
930
931 /* Build delta t1-t2 as apic timer counts down */
932 delta = lapic_cal_t1 - lapic_cal_t2;
933 apic_printk(APIC_VERBOSE, "... lapic delta = %ld\n", delta);
934
935 deltatsc = (long)(lapic_cal_tsc2 - lapic_cal_tsc1);
936
937 /* we trust the PM based calibration if possible */
938 pm_referenced = !calibrate_by_pmtimer(lapic_cal_pm2 - lapic_cal_pm1,
939 &delta, &deltatsc);
940
941 lapic_timer_period = (delta * APIC_DIVISOR) / LAPIC_CAL_LOOPS;
942 lapic_init_clockevent();
943
944 apic_printk(APIC_VERBOSE, "..... delta %ld\n", delta);
945 apic_printk(APIC_VERBOSE, "..... mult: %u\n", lapic_clockevent.mult);
946 apic_printk(APIC_VERBOSE, "..... calibration result: %u\n",
947 lapic_timer_period);
948
949 if (boot_cpu_has(X86_FEATURE_TSC)) {
950 apic_printk(APIC_VERBOSE, "..... CPU clock speed is "
951 "%ld.%04ld MHz.\n",
952 (deltatsc / LAPIC_CAL_LOOPS) / (1000000 / HZ),
953 (deltatsc / LAPIC_CAL_LOOPS) % (1000000 / HZ));
954 }
955
956 apic_printk(APIC_VERBOSE, "..... host bus clock speed is "
957 "%u.%04u MHz.\n",
958 lapic_timer_period / (1000000 / HZ),
959 lapic_timer_period % (1000000 / HZ));
960
961 /*
962 * Do a sanity check on the APIC calibration result
963 */
964 if (lapic_timer_period < (1000000 / HZ)) {
965 local_irq_enable();
966 pr_warn("APIC frequency too slow, disabling apic timer\n");
967 return -1;
968 }
969
970 levt->features &= ~CLOCK_EVT_FEAT_DUMMY;
971
972 /*
973 * PM timer calibration failed or not turned on so lets try APIC
974 * timer based calibration, if a global clockevent device is
975 * available.
976 */
977 if (!pm_referenced && global_clock_event) {
978 apic_printk(APIC_VERBOSE, "... verify APIC timer\n");
979
980 /*
981 * Setup the apic timer manually
982 */
983 levt->event_handler = lapic_cal_handler;
984 lapic_timer_set_periodic(levt);
985 lapic_cal_loops = -1;
986
987 /* Let the interrupts run */
988 local_irq_enable();
989
990 while (lapic_cal_loops <= LAPIC_CAL_LOOPS)
991 cpu_relax();
992
993 /* Stop the lapic timer */
994 local_irq_disable();
995 lapic_timer_shutdown(levt);
996
997 /* Jiffies delta */
998 deltaj = lapic_cal_j2 - lapic_cal_j1;
999 apic_printk(APIC_VERBOSE, "... jiffies delta = %lu\n", deltaj);
1000
1001 /* Check, if the jiffies result is consistent */
1002 if (deltaj >= LAPIC_CAL_LOOPS-2 && deltaj <= LAPIC_CAL_LOOPS+2)
1003 apic_printk(APIC_VERBOSE, "... jiffies result ok\n");
1004 else
1005 levt->features |= CLOCK_EVT_FEAT_DUMMY;
1006 }
1007 local_irq_enable();
1008
1009 if (levt->features & CLOCK_EVT_FEAT_DUMMY) {
1010 pr_warn("APIC timer disabled due to verification failure\n");
1011 return -1;
1012 }
1013
1014 return 0;
1015}
1016
1017/*
1018 * Setup the boot APIC
1019 *
1020 * Calibrate and verify the result.
1021 */
1022void __init setup_boot_APIC_clock(void)
1023{
1024 /*
1025 * The local apic timer can be disabled via the kernel
1026 * commandline or from the CPU detection code. Register the lapic
1027 * timer as a dummy clock event source on SMP systems, so the
1028 * broadcast mechanism is used. On UP systems simply ignore it.
1029 */
1030 if (disable_apic_timer) {
1031 pr_info("Disabling APIC timer\n");
1032 /* No broadcast on UP ! */
1033 if (num_possible_cpus() > 1) {
1034 lapic_clockevent.mult = 1;
1035 setup_APIC_timer();
1036 }
1037 return;
1038 }
1039
1040 if (calibrate_APIC_clock()) {
1041 /* No broadcast on UP ! */
1042 if (num_possible_cpus() > 1)
1043 setup_APIC_timer();
1044 return;
1045 }
1046
1047 /*
1048 * If nmi_watchdog is set to IO_APIC, we need the
1049 * PIT/HPET going. Otherwise register lapic as a dummy
1050 * device.
1051 */
1052 lapic_clockevent.features &= ~CLOCK_EVT_FEAT_DUMMY;
1053
1054 /* Setup the lapic or request the broadcast */
1055 setup_APIC_timer();
1056 amd_e400_c1e_apic_setup();
1057}
1058
1059void setup_secondary_APIC_clock(void)
1060{
1061 setup_APIC_timer();
1062 amd_e400_c1e_apic_setup();
1063}
1064
1065/*
1066 * The guts of the apic timer interrupt
1067 */
1068static void local_apic_timer_interrupt(void)
1069{
1070 struct clock_event_device *evt = this_cpu_ptr(&lapic_events);
1071
1072 /*
1073 * Normally we should not be here till LAPIC has been initialized but
1074 * in some cases like kdump, its possible that there is a pending LAPIC
1075 * timer interrupt from previous kernel's context and is delivered in
1076 * new kernel the moment interrupts are enabled.
1077 *
1078 * Interrupts are enabled early and LAPIC is setup much later, hence
1079 * its possible that when we get here evt->event_handler is NULL.
1080 * Check for event_handler being NULL and discard the interrupt as
1081 * spurious.
1082 */
1083 if (!evt->event_handler) {
1084 pr_warn("Spurious LAPIC timer interrupt on cpu %d\n",
1085 smp_processor_id());
1086 /* Switch it off */
1087 lapic_timer_shutdown(evt);
1088 return;
1089 }
1090
1091 /*
1092 * the NMI deadlock-detector uses this.
1093 */
1094 inc_irq_stat(apic_timer_irqs);
1095
1096 evt->event_handler(evt);
1097}
1098
1099/*
1100 * Local APIC timer interrupt. This is the most natural way for doing
1101 * local interrupts, but local timer interrupts can be emulated by
1102 * broadcast interrupts too. [in case the hw doesn't support APIC timers]
1103 *
1104 * [ if a single-CPU system runs an SMP kernel then we call the local
1105 * interrupt as well. Thus we cannot inline the local irq ... ]
1106 */
1107DEFINE_IDTENTRY_SYSVEC(sysvec_apic_timer_interrupt)
1108{
1109 struct pt_regs *old_regs = set_irq_regs(regs);
1110
1111 ack_APIC_irq();
1112 trace_local_timer_entry(LOCAL_TIMER_VECTOR);
1113 local_apic_timer_interrupt();
1114 trace_local_timer_exit(LOCAL_TIMER_VECTOR);
1115
1116 set_irq_regs(old_regs);
1117}
1118
1119/*
1120 * Local APIC start and shutdown
1121 */
1122
1123/**
1124 * clear_local_APIC - shutdown the local APIC
1125 *
1126 * This is called, when a CPU is disabled and before rebooting, so the state of
1127 * the local APIC has no dangling leftovers. Also used to cleanout any BIOS
1128 * leftovers during boot.
1129 */
1130void clear_local_APIC(void)
1131{
1132 int maxlvt;
1133 u32 v;
1134
1135 /* APIC hasn't been mapped yet */
1136 if (!x2apic_mode && !apic_phys)
1137 return;
1138
1139 maxlvt = lapic_get_maxlvt();
1140 /*
1141 * Masking an LVT entry can trigger a local APIC error
1142 * if the vector is zero. Mask LVTERR first to prevent this.
1143 */
1144 if (maxlvt >= 3) {
1145 v = ERROR_APIC_VECTOR; /* any non-zero vector will do */
1146 apic_write(APIC_LVTERR, v | APIC_LVT_MASKED);
1147 }
1148 /*
1149 * Careful: we have to set masks only first to deassert
1150 * any level-triggered sources.
1151 */
1152 v = apic_read(APIC_LVTT);
1153 apic_write(APIC_LVTT, v | APIC_LVT_MASKED);
1154 v = apic_read(APIC_LVT0);
1155 apic_write(APIC_LVT0, v | APIC_LVT_MASKED);
1156 v = apic_read(APIC_LVT1);
1157 apic_write(APIC_LVT1, v | APIC_LVT_MASKED);
1158 if (maxlvt >= 4) {
1159 v = apic_read(APIC_LVTPC);
1160 apic_write(APIC_LVTPC, v | APIC_LVT_MASKED);
1161 }
1162
1163 /* lets not touch this if we didn't frob it */
1164#ifdef CONFIG_X86_THERMAL_VECTOR
1165 if (maxlvt >= 5) {
1166 v = apic_read(APIC_LVTTHMR);
1167 apic_write(APIC_LVTTHMR, v | APIC_LVT_MASKED);
1168 }
1169#endif
1170#ifdef CONFIG_X86_MCE_INTEL
1171 if (maxlvt >= 6) {
1172 v = apic_read(APIC_LVTCMCI);
1173 if (!(v & APIC_LVT_MASKED))
1174 apic_write(APIC_LVTCMCI, v | APIC_LVT_MASKED);
1175 }
1176#endif
1177
1178 /*
1179 * Clean APIC state for other OSs:
1180 */
1181 apic_write(APIC_LVTT, APIC_LVT_MASKED);
1182 apic_write(APIC_LVT0, APIC_LVT_MASKED);
1183 apic_write(APIC_LVT1, APIC_LVT_MASKED);
1184 if (maxlvt >= 3)
1185 apic_write(APIC_LVTERR, APIC_LVT_MASKED);
1186 if (maxlvt >= 4)
1187 apic_write(APIC_LVTPC, APIC_LVT_MASKED);
1188
1189 /* Integrated APIC (!82489DX) ? */
1190 if (lapic_is_integrated()) {
1191 if (maxlvt > 3)
1192 /* Clear ESR due to Pentium errata 3AP and 11AP */
1193 apic_write(APIC_ESR, 0);
1194 apic_read(APIC_ESR);
1195 }
1196}
1197
1198/**
1199 * apic_soft_disable - Clears and software disables the local APIC on hotplug
1200 *
1201 * Contrary to disable_local_APIC() this does not touch the enable bit in
1202 * MSR_IA32_APICBASE. Clearing that bit on systems based on the 3 wire APIC
1203 * bus would require a hardware reset as the APIC would lose track of bus
1204 * arbitration. On systems with FSB delivery APICBASE could be disabled,
1205 * but it has to be guaranteed that no interrupt is sent to the APIC while
1206 * in that state and it's not clear from the SDM whether it still responds
1207 * to INIT/SIPI messages. Stay on the safe side and use software disable.
1208 */
1209void apic_soft_disable(void)
1210{
1211 u32 value;
1212
1213 clear_local_APIC();
1214
1215 /* Soft disable APIC (implies clearing of registers for 82489DX!). */
1216 value = apic_read(APIC_SPIV);
1217 value &= ~APIC_SPIV_APIC_ENABLED;
1218 apic_write(APIC_SPIV, value);
1219}
1220
1221/**
1222 * disable_local_APIC - clear and disable the local APIC
1223 */
1224void disable_local_APIC(void)
1225{
1226 /* APIC hasn't been mapped yet */
1227 if (!x2apic_mode && !apic_phys)
1228 return;
1229
1230 apic_soft_disable();
1231
1232#ifdef CONFIG_X86_32
1233 /*
1234 * When LAPIC was disabled by the BIOS and enabled by the kernel,
1235 * restore the disabled state.
1236 */
1237 if (enabled_via_apicbase) {
1238 unsigned int l, h;
1239
1240 rdmsr(MSR_IA32_APICBASE, l, h);
1241 l &= ~MSR_IA32_APICBASE_ENABLE;
1242 wrmsr(MSR_IA32_APICBASE, l, h);
1243 }
1244#endif
1245}
1246
1247/*
1248 * If Linux enabled the LAPIC against the BIOS default disable it down before
1249 * re-entering the BIOS on shutdown. Otherwise the BIOS may get confused and
1250 * not power-off. Additionally clear all LVT entries before disable_local_APIC
1251 * for the case where Linux didn't enable the LAPIC.
1252 */
1253void lapic_shutdown(void)
1254{
1255 unsigned long flags;
1256
1257 if (!boot_cpu_has(X86_FEATURE_APIC) && !apic_from_smp_config())
1258 return;
1259
1260 local_irq_save(flags);
1261
1262#ifdef CONFIG_X86_32
1263 if (!enabled_via_apicbase)
1264 clear_local_APIC();
1265 else
1266#endif
1267 disable_local_APIC();
1268
1269
1270 local_irq_restore(flags);
1271}
1272
1273/**
1274 * sync_Arb_IDs - synchronize APIC bus arbitration IDs
1275 */
1276void __init sync_Arb_IDs(void)
1277{
1278 /*
1279 * Unsupported on P4 - see Intel Dev. Manual Vol. 3, Ch. 8.6.1 And not
1280 * needed on AMD.
1281 */
1282 if (modern_apic() || boot_cpu_data.x86_vendor == X86_VENDOR_AMD)
1283 return;
1284
1285 /*
1286 * Wait for idle.
1287 */
1288 apic_wait_icr_idle();
1289
1290 apic_printk(APIC_DEBUG, "Synchronizing Arb IDs.\n");
1291 apic_write(APIC_ICR, APIC_DEST_ALLINC |
1292 APIC_INT_LEVELTRIG | APIC_DM_INIT);
1293}
1294
1295enum apic_intr_mode_id apic_intr_mode __ro_after_init;
1296
1297static int __init __apic_intr_mode_select(void)
1298{
1299 /* Check kernel option */
1300 if (disable_apic) {
1301 pr_info("APIC disabled via kernel command line\n");
1302 return APIC_PIC;
1303 }
1304
1305 /* Check BIOS */
1306#ifdef CONFIG_X86_64
1307 /* On 64-bit, the APIC must be integrated, Check local APIC only */
1308 if (!boot_cpu_has(X86_FEATURE_APIC)) {
1309 disable_apic = 1;
1310 pr_info("APIC disabled by BIOS\n");
1311 return APIC_PIC;
1312 }
1313#else
1314 /* On 32-bit, the APIC may be integrated APIC or 82489DX */
1315
1316 /* Neither 82489DX nor integrated APIC ? */
1317 if (!boot_cpu_has(X86_FEATURE_APIC) && !smp_found_config) {
1318 disable_apic = 1;
1319 return APIC_PIC;
1320 }
1321
1322 /* If the BIOS pretends there is an integrated APIC ? */
1323 if (!boot_cpu_has(X86_FEATURE_APIC) &&
1324 APIC_INTEGRATED(boot_cpu_apic_version)) {
1325 disable_apic = 1;
1326 pr_err(FW_BUG "Local APIC %d not detected, force emulation\n",
1327 boot_cpu_physical_apicid);
1328 return APIC_PIC;
1329 }
1330#endif
1331
1332 /* Check MP table or ACPI MADT configuration */
1333 if (!smp_found_config) {
1334 disable_ioapic_support();
1335 if (!acpi_lapic) {
1336 pr_info("APIC: ACPI MADT or MP tables are not detected\n");
1337 return APIC_VIRTUAL_WIRE_NO_CONFIG;
1338 }
1339 return APIC_VIRTUAL_WIRE;
1340 }
1341
1342#ifdef CONFIG_SMP
1343 /* If SMP should be disabled, then really disable it! */
1344 if (!setup_max_cpus) {
1345 pr_info("APIC: SMP mode deactivated\n");
1346 return APIC_SYMMETRIC_IO_NO_ROUTING;
1347 }
1348
1349 if (read_apic_id() != boot_cpu_physical_apicid) {
1350 panic("Boot APIC ID in local APIC unexpected (%d vs %d)",
1351 read_apic_id(), boot_cpu_physical_apicid);
1352 /* Or can we switch back to PIC here? */
1353 }
1354#endif
1355
1356 return APIC_SYMMETRIC_IO;
1357}
1358
1359/* Select the interrupt delivery mode for the BSP */
1360void __init apic_intr_mode_select(void)
1361{
1362 apic_intr_mode = __apic_intr_mode_select();
1363}
1364
1365/*
1366 * An initial setup of the virtual wire mode.
1367 */
1368void __init init_bsp_APIC(void)
1369{
1370 unsigned int value;
1371
1372 /*
1373 * Don't do the setup now if we have a SMP BIOS as the
1374 * through-I/O-APIC virtual wire mode might be active.
1375 */
1376 if (smp_found_config || !boot_cpu_has(X86_FEATURE_APIC))
1377 return;
1378
1379 /*
1380 * Do not trust the local APIC being empty at bootup.
1381 */
1382 clear_local_APIC();
1383
1384 /*
1385 * Enable APIC.
1386 */
1387 value = apic_read(APIC_SPIV);
1388 value &= ~APIC_VECTOR_MASK;
1389 value |= APIC_SPIV_APIC_ENABLED;
1390
1391#ifdef CONFIG_X86_32
1392 /* This bit is reserved on P4/Xeon and should be cleared */
1393 if ((boot_cpu_data.x86_vendor == X86_VENDOR_INTEL) &&
1394 (boot_cpu_data.x86 == 15))
1395 value &= ~APIC_SPIV_FOCUS_DISABLED;
1396 else
1397#endif
1398 value |= APIC_SPIV_FOCUS_DISABLED;
1399 value |= SPURIOUS_APIC_VECTOR;
1400 apic_write(APIC_SPIV, value);
1401
1402 /*
1403 * Set up the virtual wire mode.
1404 */
1405 apic_write(APIC_LVT0, APIC_DM_EXTINT);
1406 value = APIC_DM_NMI;
1407 if (!lapic_is_integrated()) /* 82489DX */
1408 value |= APIC_LVT_LEVEL_TRIGGER;
1409 if (apic_extnmi == APIC_EXTNMI_NONE)
1410 value |= APIC_LVT_MASKED;
1411 apic_write(APIC_LVT1, value);
1412}
1413
1414static void __init apic_bsp_setup(bool upmode);
1415
1416/* Init the interrupt delivery mode for the BSP */
1417void __init apic_intr_mode_init(void)
1418{
1419 bool upmode = IS_ENABLED(CONFIG_UP_LATE_INIT);
1420
1421 switch (apic_intr_mode) {
1422 case APIC_PIC:
1423 pr_info("APIC: Keep in PIC mode(8259)\n");
1424 return;
1425 case APIC_VIRTUAL_WIRE:
1426 pr_info("APIC: Switch to virtual wire mode setup\n");
1427 break;
1428 case APIC_VIRTUAL_WIRE_NO_CONFIG:
1429 pr_info("APIC: Switch to virtual wire mode setup with no configuration\n");
1430 upmode = true;
1431 break;
1432 case APIC_SYMMETRIC_IO:
1433 pr_info("APIC: Switch to symmetric I/O mode setup\n");
1434 break;
1435 case APIC_SYMMETRIC_IO_NO_ROUTING:
1436 pr_info("APIC: Switch to symmetric I/O mode setup in no SMP routine\n");
1437 break;
1438 }
1439
1440 default_setup_apic_routing();
1441
1442 if (x86_platform.apic_post_init)
1443 x86_platform.apic_post_init();
1444
1445 apic_bsp_setup(upmode);
1446}
1447
1448static void lapic_setup_esr(void)
1449{
1450 unsigned int oldvalue, value, maxlvt;
1451
1452 if (!lapic_is_integrated()) {
1453 pr_info("No ESR for 82489DX.\n");
1454 return;
1455 }
1456
1457 if (apic->disable_esr) {
1458 /*
1459 * Something untraceable is creating bad interrupts on
1460 * secondary quads ... for the moment, just leave the
1461 * ESR disabled - we can't do anything useful with the
1462 * errors anyway - mbligh
1463 */
1464 pr_info("Leaving ESR disabled.\n");
1465 return;
1466 }
1467
1468 maxlvt = lapic_get_maxlvt();
1469 if (maxlvt > 3) /* Due to the Pentium erratum 3AP. */
1470 apic_write(APIC_ESR, 0);
1471 oldvalue = apic_read(APIC_ESR);
1472
1473 /* enables sending errors */
1474 value = ERROR_APIC_VECTOR;
1475 apic_write(APIC_LVTERR, value);
1476
1477 /*
1478 * spec says clear errors after enabling vector.
1479 */
1480 if (maxlvt > 3)
1481 apic_write(APIC_ESR, 0);
1482 value = apic_read(APIC_ESR);
1483 if (value != oldvalue)
1484 apic_printk(APIC_VERBOSE, "ESR value before enabling "
1485 "vector: 0x%08x after: 0x%08x\n",
1486 oldvalue, value);
1487}
1488
1489#define APIC_IR_REGS APIC_ISR_NR
1490#define APIC_IR_BITS (APIC_IR_REGS * 32)
1491#define APIC_IR_MAPSIZE (APIC_IR_BITS / BITS_PER_LONG)
1492
1493union apic_ir {
1494 unsigned long map[APIC_IR_MAPSIZE];
1495 u32 regs[APIC_IR_REGS];
1496};
1497
1498static bool apic_check_and_ack(union apic_ir *irr, union apic_ir *isr)
1499{
1500 int i, bit;
1501
1502 /* Read the IRRs */
1503 for (i = 0; i < APIC_IR_REGS; i++)
1504 irr->regs[i] = apic_read(APIC_IRR + i * 0x10);
1505
1506 /* Read the ISRs */
1507 for (i = 0; i < APIC_IR_REGS; i++)
1508 isr->regs[i] = apic_read(APIC_ISR + i * 0x10);
1509
1510 /*
1511 * If the ISR map is not empty. ACK the APIC and run another round
1512 * to verify whether a pending IRR has been unblocked and turned
1513 * into a ISR.
1514 */
1515 if (!bitmap_empty(isr->map, APIC_IR_BITS)) {
1516 /*
1517 * There can be multiple ISR bits set when a high priority
1518 * interrupt preempted a lower priority one. Issue an ACK
1519 * per set bit.
1520 */
1521 for_each_set_bit(bit, isr->map, APIC_IR_BITS)
1522 ack_APIC_irq();
1523 return true;
1524 }
1525
1526 return !bitmap_empty(irr->map, APIC_IR_BITS);
1527}
1528
1529/*
1530 * After a crash, we no longer service the interrupts and a pending
1531 * interrupt from previous kernel might still have ISR bit set.
1532 *
1533 * Most probably by now the CPU has serviced that pending interrupt and it
1534 * might not have done the ack_APIC_irq() because it thought, interrupt
1535 * came from i8259 as ExtInt. LAPIC did not get EOI so it does not clear
1536 * the ISR bit and cpu thinks it has already serviced the interrupt. Hence
1537 * a vector might get locked. It was noticed for timer irq (vector
1538 * 0x31). Issue an extra EOI to clear ISR.
1539 *
1540 * If there are pending IRR bits they turn into ISR bits after a higher
1541 * priority ISR bit has been acked.
1542 */
1543static void apic_pending_intr_clear(void)
1544{
1545 union apic_ir irr, isr;
1546 unsigned int i;
1547
1548 /* 512 loops are way oversized and give the APIC a chance to obey. */
1549 for (i = 0; i < 512; i++) {
1550 if (!apic_check_and_ack(&irr, &isr))
1551 return;
1552 }
1553 /* Dump the IRR/ISR content if that failed */
1554 pr_warn("APIC: Stale IRR: %256pb ISR: %256pb\n", irr.map, isr.map);
1555}
1556
1557/**
1558 * setup_local_APIC - setup the local APIC
1559 *
1560 * Used to setup local APIC while initializing BSP or bringing up APs.
1561 * Always called with preemption disabled.
1562 */
1563static void setup_local_APIC(void)
1564{
1565 int cpu = smp_processor_id();
1566 unsigned int value;
1567
1568 if (disable_apic) {
1569 disable_ioapic_support();
1570 return;
1571 }
1572
1573 /*
1574 * If this comes from kexec/kcrash the APIC might be enabled in
1575 * SPIV. Soft disable it before doing further initialization.
1576 */
1577 value = apic_read(APIC_SPIV);
1578 value &= ~APIC_SPIV_APIC_ENABLED;
1579 apic_write(APIC_SPIV, value);
1580
1581#ifdef CONFIG_X86_32
1582 /* Pound the ESR really hard over the head with a big hammer - mbligh */
1583 if (lapic_is_integrated() && apic->disable_esr) {
1584 apic_write(APIC_ESR, 0);
1585 apic_write(APIC_ESR, 0);
1586 apic_write(APIC_ESR, 0);
1587 apic_write(APIC_ESR, 0);
1588 }
1589#endif
1590 /*
1591 * Double-check whether this APIC is really registered.
1592 * This is meaningless in clustered apic mode, so we skip it.
1593 */
1594 BUG_ON(!apic->apic_id_registered());
1595
1596 /*
1597 * Intel recommends to set DFR, LDR and TPR before enabling
1598 * an APIC. See e.g. "AP-388 82489DX User's Manual" (Intel
1599 * document number 292116). So here it goes...
1600 */
1601 apic->init_apic_ldr();
1602
1603#ifdef CONFIG_X86_32
1604 if (apic->dest_mode_logical) {
1605 int logical_apicid, ldr_apicid;
1606
1607 /*
1608 * APIC LDR is initialized. If logical_apicid mapping was
1609 * initialized during get_smp_config(), make sure it matches
1610 * the actual value.
1611 */
1612 logical_apicid = early_per_cpu(x86_cpu_to_logical_apicid, cpu);
1613 ldr_apicid = GET_APIC_LOGICAL_ID(apic_read(APIC_LDR));
1614 if (logical_apicid != BAD_APICID)
1615 WARN_ON(logical_apicid != ldr_apicid);
1616 /* Always use the value from LDR. */
1617 early_per_cpu(x86_cpu_to_logical_apicid, cpu) = ldr_apicid;
1618 }
1619#endif
1620
1621 /*
1622 * Set Task Priority to 'accept all except vectors 0-31'. An APIC
1623 * vector in the 16-31 range could be delivered if TPR == 0, but we
1624 * would think it's an exception and terrible things will happen. We
1625 * never change this later on.
1626 */
1627 value = apic_read(APIC_TASKPRI);
1628 value &= ~APIC_TPRI_MASK;
1629 value |= 0x10;
1630 apic_write(APIC_TASKPRI, value);
1631
1632 /* Clear eventually stale ISR/IRR bits */
1633 apic_pending_intr_clear();
1634
1635 /*
1636 * Now that we are all set up, enable the APIC
1637 */
1638 value = apic_read(APIC_SPIV);
1639 value &= ~APIC_VECTOR_MASK;
1640 /*
1641 * Enable APIC
1642 */
1643 value |= APIC_SPIV_APIC_ENABLED;
1644
1645#ifdef CONFIG_X86_32
1646 /*
1647 * Some unknown Intel IO/APIC (or APIC) errata is biting us with
1648 * certain networking cards. If high frequency interrupts are
1649 * happening on a particular IOAPIC pin, plus the IOAPIC routing
1650 * entry is masked/unmasked at a high rate as well then sooner or
1651 * later IOAPIC line gets 'stuck', no more interrupts are received
1652 * from the device. If focus CPU is disabled then the hang goes
1653 * away, oh well :-(
1654 *
1655 * [ This bug can be reproduced easily with a level-triggered
1656 * PCI Ne2000 networking cards and PII/PIII processors, dual
1657 * BX chipset. ]
1658 */
1659 /*
1660 * Actually disabling the focus CPU check just makes the hang less
1661 * frequent as it makes the interrupt distribution model be more
1662 * like LRU than MRU (the short-term load is more even across CPUs).
1663 */
1664
1665 /*
1666 * - enable focus processor (bit==0)
1667 * - 64bit mode always use processor focus
1668 * so no need to set it
1669 */
1670 value &= ~APIC_SPIV_FOCUS_DISABLED;
1671#endif
1672
1673 /*
1674 * Set spurious IRQ vector
1675 */
1676 value |= SPURIOUS_APIC_VECTOR;
1677 apic_write(APIC_SPIV, value);
1678
1679 perf_events_lapic_init();
1680
1681 /*
1682 * Set up LVT0, LVT1:
1683 *
1684 * set up through-local-APIC on the boot CPU's LINT0. This is not
1685 * strictly necessary in pure symmetric-IO mode, but sometimes
1686 * we delegate interrupts to the 8259A.
1687 */
1688 /*
1689 * TODO: set up through-local-APIC from through-I/O-APIC? --macro
1690 */
1691 value = apic_read(APIC_LVT0) & APIC_LVT_MASKED;
1692 if (!cpu && (pic_mode || !value || skip_ioapic_setup)) {
1693 value = APIC_DM_EXTINT;
1694 apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n", cpu);
1695 } else {
1696 value = APIC_DM_EXTINT | APIC_LVT_MASKED;
1697 apic_printk(APIC_VERBOSE, "masked ExtINT on CPU#%d\n", cpu);
1698 }
1699 apic_write(APIC_LVT0, value);
1700
1701 /*
1702 * Only the BSP sees the LINT1 NMI signal by default. This can be
1703 * modified by apic_extnmi= boot option.
1704 */
1705 if ((!cpu && apic_extnmi != APIC_EXTNMI_NONE) ||
1706 apic_extnmi == APIC_EXTNMI_ALL)
1707 value = APIC_DM_NMI;
1708 else
1709 value = APIC_DM_NMI | APIC_LVT_MASKED;
1710
1711 /* Is 82489DX ? */
1712 if (!lapic_is_integrated())
1713 value |= APIC_LVT_LEVEL_TRIGGER;
1714 apic_write(APIC_LVT1, value);
1715
1716#ifdef CONFIG_X86_MCE_INTEL
1717 /* Recheck CMCI information after local APIC is up on CPU #0 */
1718 if (!cpu)
1719 cmci_recheck();
1720#endif
1721}
1722
1723static void end_local_APIC_setup(void)
1724{
1725 lapic_setup_esr();
1726
1727#ifdef CONFIG_X86_32
1728 {
1729 unsigned int value;
1730 /* Disable the local apic timer */
1731 value = apic_read(APIC_LVTT);
1732 value |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR);
1733 apic_write(APIC_LVTT, value);
1734 }
1735#endif
1736
1737 apic_pm_activate();
1738}
1739
1740/*
1741 * APIC setup function for application processors. Called from smpboot.c
1742 */
1743void apic_ap_setup(void)
1744{
1745 setup_local_APIC();
1746 end_local_APIC_setup();
1747}
1748
1749#ifdef CONFIG_X86_X2APIC
1750int x2apic_mode;
1751EXPORT_SYMBOL_GPL(x2apic_mode);
1752
1753enum {
1754 X2APIC_OFF,
1755 X2APIC_DISABLED,
1756 /* All states below here have X2APIC enabled */
1757 X2APIC_ON,
1758 X2APIC_ON_LOCKED
1759};
1760static int x2apic_state;
1761
1762static bool x2apic_hw_locked(void)
1763{
1764 u64 ia32_cap;
1765 u64 msr;
1766
1767 ia32_cap = x86_read_arch_cap_msr();
1768 if (ia32_cap & ARCH_CAP_XAPIC_DISABLE) {
1769 rdmsrl(MSR_IA32_XAPIC_DISABLE_STATUS, msr);
1770 return (msr & LEGACY_XAPIC_DISABLED);
1771 }
1772 return false;
1773}
1774
1775static void __x2apic_disable(void)
1776{
1777 u64 msr;
1778
1779 if (!boot_cpu_has(X86_FEATURE_APIC))
1780 return;
1781
1782 rdmsrl(MSR_IA32_APICBASE, msr);
1783 if (!(msr & X2APIC_ENABLE))
1784 return;
1785 /* Disable xapic and x2apic first and then reenable xapic mode */
1786 wrmsrl(MSR_IA32_APICBASE, msr & ~(X2APIC_ENABLE | XAPIC_ENABLE));
1787 wrmsrl(MSR_IA32_APICBASE, msr & ~X2APIC_ENABLE);
1788 printk_once(KERN_INFO "x2apic disabled\n");
1789}
1790
1791static void __x2apic_enable(void)
1792{
1793 u64 msr;
1794
1795 rdmsrl(MSR_IA32_APICBASE, msr);
1796 if (msr & X2APIC_ENABLE)
1797 return;
1798 wrmsrl(MSR_IA32_APICBASE, msr | X2APIC_ENABLE);
1799 printk_once(KERN_INFO "x2apic enabled\n");
1800}
1801
1802static int __init setup_nox2apic(char *str)
1803{
1804 if (x2apic_enabled()) {
1805 int apicid = native_apic_msr_read(APIC_ID);
1806
1807 if (apicid >= 255) {
1808 pr_warn("Apicid: %08x, cannot enforce nox2apic\n",
1809 apicid);
1810 return 0;
1811 }
1812 if (x2apic_hw_locked()) {
1813 pr_warn("APIC locked in x2apic mode, can't disable\n");
1814 return 0;
1815 }
1816 pr_warn("x2apic already enabled.\n");
1817 __x2apic_disable();
1818 }
1819 setup_clear_cpu_cap(X86_FEATURE_X2APIC);
1820 x2apic_state = X2APIC_DISABLED;
1821 x2apic_mode = 0;
1822 return 0;
1823}
1824early_param("nox2apic", setup_nox2apic);
1825
1826/* Called from cpu_init() to enable x2apic on (secondary) cpus */
1827void x2apic_setup(void)
1828{
1829 /*
1830 * Try to make the AP's APIC state match that of the BSP, but if the
1831 * BSP is unlocked and the AP is locked then there is a state mismatch.
1832 * Warn about the mismatch in case a GP fault occurs due to a locked AP
1833 * trying to be turned off.
1834 */
1835 if (x2apic_state != X2APIC_ON_LOCKED && x2apic_hw_locked())
1836 pr_warn("x2apic lock mismatch between BSP and AP.\n");
1837 /*
1838 * If x2apic is not in ON or LOCKED state, disable it if already enabled
1839 * from BIOS.
1840 */
1841 if (x2apic_state < X2APIC_ON) {
1842 __x2apic_disable();
1843 return;
1844 }
1845 __x2apic_enable();
1846}
1847
1848static __init void x2apic_disable(void)
1849{
1850 u32 x2apic_id, state = x2apic_state;
1851
1852 x2apic_mode = 0;
1853 x2apic_state = X2APIC_DISABLED;
1854
1855 if (state != X2APIC_ON)
1856 return;
1857
1858 x2apic_id = read_apic_id();
1859 if (x2apic_id >= 255)
1860 panic("Cannot disable x2apic, id: %08x\n", x2apic_id);
1861
1862 if (x2apic_hw_locked()) {
1863 pr_warn("Cannot disable locked x2apic, id: %08x\n", x2apic_id);
1864 return;
1865 }
1866
1867 __x2apic_disable();
1868 register_lapic_address(mp_lapic_addr);
1869}
1870
1871static __init void x2apic_enable(void)
1872{
1873 if (x2apic_state != X2APIC_OFF)
1874 return;
1875
1876 x2apic_mode = 1;
1877 x2apic_state = X2APIC_ON;
1878 __x2apic_enable();
1879}
1880
1881static __init void try_to_enable_x2apic(int remap_mode)
1882{
1883 if (x2apic_state == X2APIC_DISABLED)
1884 return;
1885
1886 if (remap_mode != IRQ_REMAP_X2APIC_MODE) {
1887 u32 apic_limit = 255;
1888
1889 /*
1890 * Using X2APIC without IR is not architecturally supported
1891 * on bare metal but may be supported in guests.
1892 */
1893 if (!x86_init.hyper.x2apic_available()) {
1894 pr_info("x2apic: IRQ remapping doesn't support X2APIC mode\n");
1895 x2apic_disable();
1896 return;
1897 }
1898
1899 /*
1900 * If the hypervisor supports extended destination ID in
1901 * MSI, that increases the maximum APIC ID that can be
1902 * used for non-remapped IRQ domains.
1903 */
1904 if (x86_init.hyper.msi_ext_dest_id()) {
1905 virt_ext_dest_id = 1;
1906 apic_limit = 32767;
1907 }
1908
1909 /*
1910 * Without IR, all CPUs can be addressed by IOAPIC/MSI only
1911 * in physical mode, and CPUs with an APIC ID that cannot
1912 * be addressed must not be brought online.
1913 */
1914 x2apic_set_max_apicid(apic_limit);
1915 x2apic_phys = 1;
1916 }
1917 x2apic_enable();
1918}
1919
1920void __init check_x2apic(void)
1921{
1922 if (x2apic_enabled()) {
1923 pr_info("x2apic: enabled by BIOS, switching to x2apic ops\n");
1924 x2apic_mode = 1;
1925 if (x2apic_hw_locked())
1926 x2apic_state = X2APIC_ON_LOCKED;
1927 else
1928 x2apic_state = X2APIC_ON;
1929 } else if (!boot_cpu_has(X86_FEATURE_X2APIC)) {
1930 x2apic_state = X2APIC_DISABLED;
1931 }
1932}
1933#else /* CONFIG_X86_X2APIC */
1934void __init check_x2apic(void)
1935{
1936 if (!apic_is_x2apic_enabled())
1937 return;
1938 /*
1939 * Checkme: Can we simply turn off x2APIC here instead of disabling the APIC?
1940 */
1941 pr_err("Kernel does not support x2APIC, please recompile with CONFIG_X86_X2APIC.\n");
1942 pr_err("Disabling APIC, expect reduced performance and functionality.\n");
1943
1944 disable_apic = 1;
1945 setup_clear_cpu_cap(X86_FEATURE_APIC);
1946}
1947
1948static inline void try_to_enable_x2apic(int remap_mode) { }
1949static inline void __x2apic_enable(void) { }
1950#endif /* !CONFIG_X86_X2APIC */
1951
1952void __init enable_IR_x2apic(void)
1953{
1954 unsigned long flags;
1955 int ret, ir_stat;
1956
1957 if (skip_ioapic_setup) {
1958 pr_info("Not enabling interrupt remapping due to skipped IO-APIC setup\n");
1959 return;
1960 }
1961
1962 ir_stat = irq_remapping_prepare();
1963 if (ir_stat < 0 && !x2apic_supported())
1964 return;
1965
1966 ret = save_ioapic_entries();
1967 if (ret) {
1968 pr_info("Saving IO-APIC state failed: %d\n", ret);
1969 return;
1970 }
1971
1972 local_irq_save(flags);
1973 legacy_pic->mask_all();
1974 mask_ioapic_entries();
1975
1976 /* If irq_remapping_prepare() succeeded, try to enable it */
1977 if (ir_stat >= 0)
1978 ir_stat = irq_remapping_enable();
1979 /* ir_stat contains the remap mode or an error code */
1980 try_to_enable_x2apic(ir_stat);
1981
1982 if (ir_stat < 0)
1983 restore_ioapic_entries();
1984 legacy_pic->restore_mask();
1985 local_irq_restore(flags);
1986}
1987
1988#ifdef CONFIG_X86_64
1989/*
1990 * Detect and enable local APICs on non-SMP boards.
1991 * Original code written by Keir Fraser.
1992 * On AMD64 we trust the BIOS - if it says no APIC it is likely
1993 * not correctly set up (usually the APIC timer won't work etc.)
1994 */
1995static int __init detect_init_APIC(void)
1996{
1997 if (!boot_cpu_has(X86_FEATURE_APIC)) {
1998 pr_info("No local APIC present\n");
1999 return -1;
2000 }
2001
2002 mp_lapic_addr = APIC_DEFAULT_PHYS_BASE;
2003 return 0;
2004}
2005#else
2006
2007static int __init apic_verify(void)
2008{
2009 u32 features, h, l;
2010
2011 /*
2012 * The APIC feature bit should now be enabled
2013 * in `cpuid'
2014 */
2015 features = cpuid_edx(1);
2016 if (!(features & (1 << X86_FEATURE_APIC))) {
2017 pr_warn("Could not enable APIC!\n");
2018 return -1;
2019 }
2020 set_cpu_cap(&boot_cpu_data, X86_FEATURE_APIC);
2021 mp_lapic_addr = APIC_DEFAULT_PHYS_BASE;
2022
2023 /* The BIOS may have set up the APIC at some other address */
2024 if (boot_cpu_data.x86 >= 6) {
2025 rdmsr(MSR_IA32_APICBASE, l, h);
2026 if (l & MSR_IA32_APICBASE_ENABLE)
2027 mp_lapic_addr = l & MSR_IA32_APICBASE_BASE;
2028 }
2029
2030 pr_info("Found and enabled local APIC!\n");
2031 return 0;
2032}
2033
2034int __init apic_force_enable(unsigned long addr)
2035{
2036 u32 h, l;
2037
2038 if (disable_apic)
2039 return -1;
2040
2041 /*
2042 * Some BIOSes disable the local APIC in the APIC_BASE
2043 * MSR. This can only be done in software for Intel P6 or later
2044 * and AMD K7 (Model > 1) or later.
2045 */
2046 if (boot_cpu_data.x86 >= 6) {
2047 rdmsr(MSR_IA32_APICBASE, l, h);
2048 if (!(l & MSR_IA32_APICBASE_ENABLE)) {
2049 pr_info("Local APIC disabled by BIOS -- reenabling.\n");
2050 l &= ~MSR_IA32_APICBASE_BASE;
2051 l |= MSR_IA32_APICBASE_ENABLE | addr;
2052 wrmsr(MSR_IA32_APICBASE, l, h);
2053 enabled_via_apicbase = 1;
2054 }
2055 }
2056 return apic_verify();
2057}
2058
2059/*
2060 * Detect and initialize APIC
2061 */
2062static int __init detect_init_APIC(void)
2063{
2064 /* Disabled by kernel option? */
2065 if (disable_apic)
2066 return -1;
2067
2068 switch (boot_cpu_data.x86_vendor) {
2069 case X86_VENDOR_AMD:
2070 if ((boot_cpu_data.x86 == 6 && boot_cpu_data.x86_model > 1) ||
2071 (boot_cpu_data.x86 >= 15))
2072 break;
2073 goto no_apic;
2074 case X86_VENDOR_HYGON:
2075 break;
2076 case X86_VENDOR_INTEL:
2077 if (boot_cpu_data.x86 == 6 || boot_cpu_data.x86 == 15 ||
2078 (boot_cpu_data.x86 == 5 && boot_cpu_has(X86_FEATURE_APIC)))
2079 break;
2080 goto no_apic;
2081 default:
2082 goto no_apic;
2083 }
2084
2085 if (!boot_cpu_has(X86_FEATURE_APIC)) {
2086 /*
2087 * Over-ride BIOS and try to enable the local APIC only if
2088 * "lapic" specified.
2089 */
2090 if (!force_enable_local_apic) {
2091 pr_info("Local APIC disabled by BIOS -- "
2092 "you can enable it with \"lapic\"\n");
2093 return -1;
2094 }
2095 if (apic_force_enable(APIC_DEFAULT_PHYS_BASE))
2096 return -1;
2097 } else {
2098 if (apic_verify())
2099 return -1;
2100 }
2101
2102 apic_pm_activate();
2103
2104 return 0;
2105
2106no_apic:
2107 pr_info("No local APIC present or hardware disabled\n");
2108 return -1;
2109}
2110#endif
2111
2112/**
2113 * init_apic_mappings - initialize APIC mappings
2114 */
2115void __init init_apic_mappings(void)
2116{
2117 unsigned int new_apicid;
2118
2119 if (apic_validate_deadline_timer())
2120 pr_info("TSC deadline timer available\n");
2121
2122 if (x2apic_mode) {
2123 boot_cpu_physical_apicid = read_apic_id();
2124 return;
2125 }
2126
2127 /* If no local APIC can be found return early */
2128 if (!smp_found_config && detect_init_APIC()) {
2129 /* lets NOP'ify apic operations */
2130 pr_info("APIC: disable apic facility\n");
2131 apic_disable();
2132 } else {
2133 apic_phys = mp_lapic_addr;
2134
2135 /*
2136 * If the system has ACPI MADT tables or MP info, the LAPIC
2137 * address is already registered.
2138 */
2139 if (!acpi_lapic && !smp_found_config)
2140 register_lapic_address(apic_phys);
2141 }
2142
2143 /*
2144 * Fetch the APIC ID of the BSP in case we have a
2145 * default configuration (or the MP table is broken).
2146 */
2147 new_apicid = read_apic_id();
2148 if (boot_cpu_physical_apicid != new_apicid) {
2149 boot_cpu_physical_apicid = new_apicid;
2150 /*
2151 * yeah -- we lie about apic_version
2152 * in case if apic was disabled via boot option
2153 * but it's not a problem for SMP compiled kernel
2154 * since apic_intr_mode_select is prepared for such
2155 * a case and disable smp mode
2156 */
2157 boot_cpu_apic_version = GET_APIC_VERSION(apic_read(APIC_LVR));
2158 }
2159}
2160
2161void __init register_lapic_address(unsigned long address)
2162{
2163 mp_lapic_addr = address;
2164
2165 if (!x2apic_mode) {
2166 set_fixmap_nocache(FIX_APIC_BASE, address);
2167 apic_printk(APIC_VERBOSE, "mapped APIC to %16lx (%16lx)\n",
2168 APIC_BASE, address);
2169 }
2170 if (boot_cpu_physical_apicid == -1U) {
2171 boot_cpu_physical_apicid = read_apic_id();
2172 boot_cpu_apic_version = GET_APIC_VERSION(apic_read(APIC_LVR));
2173 }
2174}
2175
2176/*
2177 * Local APIC interrupts
2178 */
2179
2180/*
2181 * Common handling code for spurious_interrupt and spurious_vector entry
2182 * points below. No point in allowing the compiler to inline it twice.
2183 */
2184static noinline void handle_spurious_interrupt(u8 vector)
2185{
2186 u32 v;
2187
2188 trace_spurious_apic_entry(vector);
2189
2190 inc_irq_stat(irq_spurious_count);
2191
2192 /*
2193 * If this is a spurious interrupt then do not acknowledge
2194 */
2195 if (vector == SPURIOUS_APIC_VECTOR) {
2196 /* See SDM vol 3 */
2197 pr_info("Spurious APIC interrupt (vector 0xFF) on CPU#%d, should never happen.\n",
2198 smp_processor_id());
2199 goto out;
2200 }
2201
2202 /*
2203 * If it is a vectored one, verify it's set in the ISR. If set,
2204 * acknowledge it.
2205 */
2206 v = apic_read(APIC_ISR + ((vector & ~0x1f) >> 1));
2207 if (v & (1 << (vector & 0x1f))) {
2208 pr_info("Spurious interrupt (vector 0x%02x) on CPU#%d. Acked\n",
2209 vector, smp_processor_id());
2210 ack_APIC_irq();
2211 } else {
2212 pr_info("Spurious interrupt (vector 0x%02x) on CPU#%d. Not pending!\n",
2213 vector, smp_processor_id());
2214 }
2215out:
2216 trace_spurious_apic_exit(vector);
2217}
2218
2219/**
2220 * spurious_interrupt - Catch all for interrupts raised on unused vectors
2221 * @regs: Pointer to pt_regs on stack
2222 * @vector: The vector number
2223 *
2224 * This is invoked from ASM entry code to catch all interrupts which
2225 * trigger on an entry which is routed to the common_spurious idtentry
2226 * point.
2227 */
2228DEFINE_IDTENTRY_IRQ(spurious_interrupt)
2229{
2230 handle_spurious_interrupt(vector);
2231}
2232
2233DEFINE_IDTENTRY_SYSVEC(sysvec_spurious_apic_interrupt)
2234{
2235 handle_spurious_interrupt(SPURIOUS_APIC_VECTOR);
2236}
2237
2238/*
2239 * This interrupt should never happen with our APIC/SMP architecture
2240 */
2241DEFINE_IDTENTRY_SYSVEC(sysvec_error_interrupt)
2242{
2243 static const char * const error_interrupt_reason[] = {
2244 "Send CS error", /* APIC Error Bit 0 */
2245 "Receive CS error", /* APIC Error Bit 1 */
2246 "Send accept error", /* APIC Error Bit 2 */
2247 "Receive accept error", /* APIC Error Bit 3 */
2248 "Redirectable IPI", /* APIC Error Bit 4 */
2249 "Send illegal vector", /* APIC Error Bit 5 */
2250 "Received illegal vector", /* APIC Error Bit 6 */
2251 "Illegal register address", /* APIC Error Bit 7 */
2252 };
2253 u32 v, i = 0;
2254
2255 trace_error_apic_entry(ERROR_APIC_VECTOR);
2256
2257 /* First tickle the hardware, only then report what went on. -- REW */
2258 if (lapic_get_maxlvt() > 3) /* Due to the Pentium erratum 3AP. */
2259 apic_write(APIC_ESR, 0);
2260 v = apic_read(APIC_ESR);
2261 ack_APIC_irq();
2262 atomic_inc(&irq_err_count);
2263
2264 apic_printk(APIC_DEBUG, KERN_DEBUG "APIC error on CPU%d: %02x",
2265 smp_processor_id(), v);
2266
2267 v &= 0xff;
2268 while (v) {
2269 if (v & 0x1)
2270 apic_printk(APIC_DEBUG, KERN_CONT " : %s", error_interrupt_reason[i]);
2271 i++;
2272 v >>= 1;
2273 }
2274
2275 apic_printk(APIC_DEBUG, KERN_CONT "\n");
2276
2277 trace_error_apic_exit(ERROR_APIC_VECTOR);
2278}
2279
2280/**
2281 * connect_bsp_APIC - attach the APIC to the interrupt system
2282 */
2283static void __init connect_bsp_APIC(void)
2284{
2285#ifdef CONFIG_X86_32
2286 if (pic_mode) {
2287 /*
2288 * Do not trust the local APIC being empty at bootup.
2289 */
2290 clear_local_APIC();
2291 /*
2292 * PIC mode, enable APIC mode in the IMCR, i.e. connect BSP's
2293 * local APIC to INT and NMI lines.
2294 */
2295 apic_printk(APIC_VERBOSE, "leaving PIC mode, "
2296 "enabling APIC mode.\n");
2297 imcr_pic_to_apic();
2298 }
2299#endif
2300}
2301
2302/**
2303 * disconnect_bsp_APIC - detach the APIC from the interrupt system
2304 * @virt_wire_setup: indicates, whether virtual wire mode is selected
2305 *
2306 * Virtual wire mode is necessary to deliver legacy interrupts even when the
2307 * APIC is disabled.
2308 */
2309void disconnect_bsp_APIC(int virt_wire_setup)
2310{
2311 unsigned int value;
2312
2313#ifdef CONFIG_X86_32
2314 if (pic_mode) {
2315 /*
2316 * Put the board back into PIC mode (has an effect only on
2317 * certain older boards). Note that APIC interrupts, including
2318 * IPIs, won't work beyond this point! The only exception are
2319 * INIT IPIs.
2320 */
2321 apic_printk(APIC_VERBOSE, "disabling APIC mode, "
2322 "entering PIC mode.\n");
2323 imcr_apic_to_pic();
2324 return;
2325 }
2326#endif
2327
2328 /* Go back to Virtual Wire compatibility mode */
2329
2330 /* For the spurious interrupt use vector F, and enable it */
2331 value = apic_read(APIC_SPIV);
2332 value &= ~APIC_VECTOR_MASK;
2333 value |= APIC_SPIV_APIC_ENABLED;
2334 value |= 0xf;
2335 apic_write(APIC_SPIV, value);
2336
2337 if (!virt_wire_setup) {
2338 /*
2339 * For LVT0 make it edge triggered, active high,
2340 * external and enabled
2341 */
2342 value = apic_read(APIC_LVT0);
2343 value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING |
2344 APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
2345 APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED);
2346 value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
2347 value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_EXTINT);
2348 apic_write(APIC_LVT0, value);
2349 } else {
2350 /* Disable LVT0 */
2351 apic_write(APIC_LVT0, APIC_LVT_MASKED);
2352 }
2353
2354 /*
2355 * For LVT1 make it edge triggered, active high,
2356 * nmi and enabled
2357 */
2358 value = apic_read(APIC_LVT1);
2359 value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING |
2360 APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
2361 APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED);
2362 value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
2363 value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_NMI);
2364 apic_write(APIC_LVT1, value);
2365}
2366
2367/*
2368 * The number of allocated logical CPU IDs. Since logical CPU IDs are allocated
2369 * contiguously, it equals to current allocated max logical CPU ID plus 1.
2370 * All allocated CPU IDs should be in the [0, nr_logical_cpuids) range,
2371 * so the maximum of nr_logical_cpuids is nr_cpu_ids.
2372 *
2373 * NOTE: Reserve 0 for BSP.
2374 */
2375static int nr_logical_cpuids = 1;
2376
2377/*
2378 * Used to store mapping between logical CPU IDs and APIC IDs.
2379 */
2380static int cpuid_to_apicid[] = {
2381 [0 ... NR_CPUS - 1] = -1,
2382};
2383
2384bool arch_match_cpu_phys_id(int cpu, u64 phys_id)
2385{
2386 return phys_id == cpuid_to_apicid[cpu];
2387}
2388
2389#ifdef CONFIG_SMP
2390/**
2391 * apic_id_is_primary_thread - Check whether APIC ID belongs to a primary thread
2392 * @apicid: APIC ID to check
2393 */
2394bool apic_id_is_primary_thread(unsigned int apicid)
2395{
2396 u32 mask;
2397
2398 if (smp_num_siblings == 1)
2399 return true;
2400 /* Isolate the SMT bit(s) in the APICID and check for 0 */
2401 mask = (1U << (fls(smp_num_siblings) - 1)) - 1;
2402 return !(apicid & mask);
2403}
2404#endif
2405
2406/*
2407 * Should use this API to allocate logical CPU IDs to keep nr_logical_cpuids
2408 * and cpuid_to_apicid[] synchronized.
2409 */
2410static int allocate_logical_cpuid(int apicid)
2411{
2412 int i;
2413
2414 /*
2415 * cpuid <-> apicid mapping is persistent, so when a cpu is up,
2416 * check if the kernel has allocated a cpuid for it.
2417 */
2418 for (i = 0; i < nr_logical_cpuids; i++) {
2419 if (cpuid_to_apicid[i] == apicid)
2420 return i;
2421 }
2422
2423 /* Allocate a new cpuid. */
2424 if (nr_logical_cpuids >= nr_cpu_ids) {
2425 WARN_ONCE(1, "APIC: NR_CPUS/possible_cpus limit of %u reached. "
2426 "Processor %d/0x%x and the rest are ignored.\n",
2427 nr_cpu_ids, nr_logical_cpuids, apicid);
2428 return -EINVAL;
2429 }
2430
2431 cpuid_to_apicid[nr_logical_cpuids] = apicid;
2432 return nr_logical_cpuids++;
2433}
2434
2435int generic_processor_info(int apicid, int version)
2436{
2437 int cpu, max = nr_cpu_ids;
2438 bool boot_cpu_detected = physid_isset(boot_cpu_physical_apicid,
2439 phys_cpu_present_map);
2440
2441 /*
2442 * boot_cpu_physical_apicid is designed to have the apicid
2443 * returned by read_apic_id(), i.e, the apicid of the
2444 * currently booting-up processor. However, on some platforms,
2445 * it is temporarily modified by the apicid reported as BSP
2446 * through MP table. Concretely:
2447 *
2448 * - arch/x86/kernel/mpparse.c: MP_processor_info()
2449 * - arch/x86/mm/amdtopology.c: amd_numa_init()
2450 *
2451 * This function is executed with the modified
2452 * boot_cpu_physical_apicid. So, disabled_cpu_apicid kernel
2453 * parameter doesn't work to disable APs on kdump 2nd kernel.
2454 *
2455 * Since fixing handling of boot_cpu_physical_apicid requires
2456 * another discussion and tests on each platform, we leave it
2457 * for now and here we use read_apic_id() directly in this
2458 * function, generic_processor_info().
2459 */
2460 if (disabled_cpu_apicid != BAD_APICID &&
2461 disabled_cpu_apicid != read_apic_id() &&
2462 disabled_cpu_apicid == apicid) {
2463 int thiscpu = num_processors + disabled_cpus;
2464
2465 pr_warn("APIC: Disabling requested cpu."
2466 " Processor %d/0x%x ignored.\n", thiscpu, apicid);
2467
2468 disabled_cpus++;
2469 return -ENODEV;
2470 }
2471
2472 /*
2473 * If boot cpu has not been detected yet, then only allow upto
2474 * nr_cpu_ids - 1 processors and keep one slot free for boot cpu
2475 */
2476 if (!boot_cpu_detected && num_processors >= nr_cpu_ids - 1 &&
2477 apicid != boot_cpu_physical_apicid) {
2478 int thiscpu = max + disabled_cpus - 1;
2479
2480 pr_warn("APIC: NR_CPUS/possible_cpus limit of %i almost"
2481 " reached. Keeping one slot for boot cpu."
2482 " Processor %d/0x%x ignored.\n", max, thiscpu, apicid);
2483
2484 disabled_cpus++;
2485 return -ENODEV;
2486 }
2487
2488 if (num_processors >= nr_cpu_ids) {
2489 int thiscpu = max + disabled_cpus;
2490
2491 pr_warn("APIC: NR_CPUS/possible_cpus limit of %i reached. "
2492 "Processor %d/0x%x ignored.\n", max, thiscpu, apicid);
2493
2494 disabled_cpus++;
2495 return -EINVAL;
2496 }
2497
2498 if (apicid == boot_cpu_physical_apicid) {
2499 /*
2500 * x86_bios_cpu_apicid is required to have processors listed
2501 * in same order as logical cpu numbers. Hence the first
2502 * entry is BSP, and so on.
2503 * boot_cpu_init() already hold bit 0 in cpu_present_mask
2504 * for BSP.
2505 */
2506 cpu = 0;
2507
2508 /* Logical cpuid 0 is reserved for BSP. */
2509 cpuid_to_apicid[0] = apicid;
2510 } else {
2511 cpu = allocate_logical_cpuid(apicid);
2512 if (cpu < 0) {
2513 disabled_cpus++;
2514 return -EINVAL;
2515 }
2516 }
2517
2518 /*
2519 * Validate version
2520 */
2521 if (version == 0x0) {
2522 pr_warn("BIOS bug: APIC version is 0 for CPU %d/0x%x, fixing up to 0x10\n",
2523 cpu, apicid);
2524 version = 0x10;
2525 }
2526
2527 if (version != boot_cpu_apic_version) {
2528 pr_warn("BIOS bug: APIC version mismatch, boot CPU: %x, CPU %d: version %x\n",
2529 boot_cpu_apic_version, cpu, version);
2530 }
2531
2532 if (apicid > max_physical_apicid)
2533 max_physical_apicid = apicid;
2534
2535#if defined(CONFIG_SMP) || defined(CONFIG_X86_64)
2536 early_per_cpu(x86_cpu_to_apicid, cpu) = apicid;
2537 early_per_cpu(x86_bios_cpu_apicid, cpu) = apicid;
2538#endif
2539#ifdef CONFIG_X86_32
2540 early_per_cpu(x86_cpu_to_logical_apicid, cpu) =
2541 apic->x86_32_early_logical_apicid(cpu);
2542#endif
2543 set_cpu_possible(cpu, true);
2544 physid_set(apicid, phys_cpu_present_map);
2545 set_cpu_present(cpu, true);
2546 num_processors++;
2547
2548 return cpu;
2549}
2550
2551int hard_smp_processor_id(void)
2552{
2553 return read_apic_id();
2554}
2555
2556void __irq_msi_compose_msg(struct irq_cfg *cfg, struct msi_msg *msg,
2557 bool dmar)
2558{
2559 memset(msg, 0, sizeof(*msg));
2560
2561 msg->arch_addr_lo.base_address = X86_MSI_BASE_ADDRESS_LOW;
2562 msg->arch_addr_lo.dest_mode_logical = apic->dest_mode_logical;
2563 msg->arch_addr_lo.destid_0_7 = cfg->dest_apicid & 0xFF;
2564
2565 msg->arch_data.delivery_mode = APIC_DELIVERY_MODE_FIXED;
2566 msg->arch_data.vector = cfg->vector;
2567
2568 msg->address_hi = X86_MSI_BASE_ADDRESS_HIGH;
2569 /*
2570 * Only the IOMMU itself can use the trick of putting destination
2571 * APIC ID into the high bits of the address. Anything else would
2572 * just be writing to memory if it tried that, and needs IR to
2573 * address APICs which can't be addressed in the normal 32-bit
2574 * address range at 0xFFExxxxx. That is typically just 8 bits, but
2575 * some hypervisors allow the extended destination ID field in bits
2576 * 5-11 to be used, giving support for 15 bits of APIC IDs in total.
2577 */
2578 if (dmar)
2579 msg->arch_addr_hi.destid_8_31 = cfg->dest_apicid >> 8;
2580 else if (virt_ext_dest_id && cfg->dest_apicid < 0x8000)
2581 msg->arch_addr_lo.virt_destid_8_14 = cfg->dest_apicid >> 8;
2582 else
2583 WARN_ON_ONCE(cfg->dest_apicid > 0xFF);
2584}
2585
2586u32 x86_msi_msg_get_destid(struct msi_msg *msg, bool extid)
2587{
2588 u32 dest = msg->arch_addr_lo.destid_0_7;
2589
2590 if (extid)
2591 dest |= msg->arch_addr_hi.destid_8_31 << 8;
2592 return dest;
2593}
2594EXPORT_SYMBOL_GPL(x86_msi_msg_get_destid);
2595
2596#ifdef CONFIG_X86_64
2597void __init acpi_wake_cpu_handler_update(wakeup_cpu_handler handler)
2598{
2599 struct apic **drv;
2600
2601 for (drv = __apicdrivers; drv < __apicdrivers_end; drv++)
2602 (*drv)->wakeup_secondary_cpu_64 = handler;
2603}
2604#endif
2605
2606/*
2607 * Override the generic EOI implementation with an optimized version.
2608 * Only called during early boot when only one CPU is active and with
2609 * interrupts disabled, so we know this does not race with actual APIC driver
2610 * use.
2611 */
2612void __init apic_set_eoi_write(void (*eoi_write)(u32 reg, u32 v))
2613{
2614 struct apic **drv;
2615
2616 for (drv = __apicdrivers; drv < __apicdrivers_end; drv++) {
2617 /* Should happen once for each apic */
2618 WARN_ON((*drv)->eoi_write == eoi_write);
2619 (*drv)->native_eoi_write = (*drv)->eoi_write;
2620 (*drv)->eoi_write = eoi_write;
2621 }
2622}
2623
2624static void __init apic_bsp_up_setup(void)
2625{
2626#ifdef CONFIG_X86_64
2627 apic_write(APIC_ID, apic->set_apic_id(boot_cpu_physical_apicid));
2628#else
2629 /*
2630 * Hack: In case of kdump, after a crash, kernel might be booting
2631 * on a cpu with non-zero lapic id. But boot_cpu_physical_apicid
2632 * might be zero if read from MP tables. Get it from LAPIC.
2633 */
2634# ifdef CONFIG_CRASH_DUMP
2635 boot_cpu_physical_apicid = read_apic_id();
2636# endif
2637#endif
2638 physid_set_mask_of_physid(boot_cpu_physical_apicid, &phys_cpu_present_map);
2639}
2640
2641/**
2642 * apic_bsp_setup - Setup function for local apic and io-apic
2643 * @upmode: Force UP mode (for APIC_init_uniprocessor)
2644 */
2645static void __init apic_bsp_setup(bool upmode)
2646{
2647 connect_bsp_APIC();
2648 if (upmode)
2649 apic_bsp_up_setup();
2650 setup_local_APIC();
2651
2652 enable_IO_APIC();
2653 end_local_APIC_setup();
2654 irq_remap_enable_fault_handling();
2655 setup_IO_APIC();
2656 lapic_update_legacy_vectors();
2657}
2658
2659#ifdef CONFIG_UP_LATE_INIT
2660void __init up_late_init(void)
2661{
2662 if (apic_intr_mode == APIC_PIC)
2663 return;
2664
2665 /* Setup local timer */
2666 x86_init.timers.setup_percpu_clockev();
2667}
2668#endif
2669
2670/*
2671 * Power management
2672 */
2673#ifdef CONFIG_PM
2674
2675static struct {
2676 /*
2677 * 'active' is true if the local APIC was enabled by us and
2678 * not the BIOS; this signifies that we are also responsible
2679 * for disabling it before entering apm/acpi suspend
2680 */
2681 int active;
2682 /* r/w apic fields */
2683 unsigned int apic_id;
2684 unsigned int apic_taskpri;
2685 unsigned int apic_ldr;
2686 unsigned int apic_dfr;
2687 unsigned int apic_spiv;
2688 unsigned int apic_lvtt;
2689 unsigned int apic_lvtpc;
2690 unsigned int apic_lvt0;
2691 unsigned int apic_lvt1;
2692 unsigned int apic_lvterr;
2693 unsigned int apic_tmict;
2694 unsigned int apic_tdcr;
2695 unsigned int apic_thmr;
2696 unsigned int apic_cmci;
2697} apic_pm_state;
2698
2699static int lapic_suspend(void)
2700{
2701 unsigned long flags;
2702 int maxlvt;
2703
2704 if (!apic_pm_state.active)
2705 return 0;
2706
2707 maxlvt = lapic_get_maxlvt();
2708
2709 apic_pm_state.apic_id = apic_read(APIC_ID);
2710 apic_pm_state.apic_taskpri = apic_read(APIC_TASKPRI);
2711 apic_pm_state.apic_ldr = apic_read(APIC_LDR);
2712 apic_pm_state.apic_dfr = apic_read(APIC_DFR);
2713 apic_pm_state.apic_spiv = apic_read(APIC_SPIV);
2714 apic_pm_state.apic_lvtt = apic_read(APIC_LVTT);
2715 if (maxlvt >= 4)
2716 apic_pm_state.apic_lvtpc = apic_read(APIC_LVTPC);
2717 apic_pm_state.apic_lvt0 = apic_read(APIC_LVT0);
2718 apic_pm_state.apic_lvt1 = apic_read(APIC_LVT1);
2719 apic_pm_state.apic_lvterr = apic_read(APIC_LVTERR);
2720 apic_pm_state.apic_tmict = apic_read(APIC_TMICT);
2721 apic_pm_state.apic_tdcr = apic_read(APIC_TDCR);
2722#ifdef CONFIG_X86_THERMAL_VECTOR
2723 if (maxlvt >= 5)
2724 apic_pm_state.apic_thmr = apic_read(APIC_LVTTHMR);
2725#endif
2726#ifdef CONFIG_X86_MCE_INTEL
2727 if (maxlvt >= 6)
2728 apic_pm_state.apic_cmci = apic_read(APIC_LVTCMCI);
2729#endif
2730
2731 local_irq_save(flags);
2732
2733 /*
2734 * Mask IOAPIC before disabling the local APIC to prevent stale IRR
2735 * entries on some implementations.
2736 */
2737 mask_ioapic_entries();
2738
2739 disable_local_APIC();
2740
2741 irq_remapping_disable();
2742
2743 local_irq_restore(flags);
2744 return 0;
2745}
2746
2747static void lapic_resume(void)
2748{
2749 unsigned int l, h;
2750 unsigned long flags;
2751 int maxlvt;
2752
2753 if (!apic_pm_state.active)
2754 return;
2755
2756 local_irq_save(flags);
2757
2758 /*
2759 * IO-APIC and PIC have their own resume routines.
2760 * We just mask them here to make sure the interrupt
2761 * subsystem is completely quiet while we enable x2apic
2762 * and interrupt-remapping.
2763 */
2764 mask_ioapic_entries();
2765 legacy_pic->mask_all();
2766
2767 if (x2apic_mode) {
2768 __x2apic_enable();
2769 } else {
2770 /*
2771 * Make sure the APICBASE points to the right address
2772 *
2773 * FIXME! This will be wrong if we ever support suspend on
2774 * SMP! We'll need to do this as part of the CPU restore!
2775 */
2776 if (boot_cpu_data.x86 >= 6) {
2777 rdmsr(MSR_IA32_APICBASE, l, h);
2778 l &= ~MSR_IA32_APICBASE_BASE;
2779 l |= MSR_IA32_APICBASE_ENABLE | mp_lapic_addr;
2780 wrmsr(MSR_IA32_APICBASE, l, h);
2781 }
2782 }
2783
2784 maxlvt = lapic_get_maxlvt();
2785 apic_write(APIC_LVTERR, ERROR_APIC_VECTOR | APIC_LVT_MASKED);
2786 apic_write(APIC_ID, apic_pm_state.apic_id);
2787 apic_write(APIC_DFR, apic_pm_state.apic_dfr);
2788 apic_write(APIC_LDR, apic_pm_state.apic_ldr);
2789 apic_write(APIC_TASKPRI, apic_pm_state.apic_taskpri);
2790 apic_write(APIC_SPIV, apic_pm_state.apic_spiv);
2791 apic_write(APIC_LVT0, apic_pm_state.apic_lvt0);
2792 apic_write(APIC_LVT1, apic_pm_state.apic_lvt1);
2793#ifdef CONFIG_X86_THERMAL_VECTOR
2794 if (maxlvt >= 5)
2795 apic_write(APIC_LVTTHMR, apic_pm_state.apic_thmr);
2796#endif
2797#ifdef CONFIG_X86_MCE_INTEL
2798 if (maxlvt >= 6)
2799 apic_write(APIC_LVTCMCI, apic_pm_state.apic_cmci);
2800#endif
2801 if (maxlvt >= 4)
2802 apic_write(APIC_LVTPC, apic_pm_state.apic_lvtpc);
2803 apic_write(APIC_LVTT, apic_pm_state.apic_lvtt);
2804 apic_write(APIC_TDCR, apic_pm_state.apic_tdcr);
2805 apic_write(APIC_TMICT, apic_pm_state.apic_tmict);
2806 apic_write(APIC_ESR, 0);
2807 apic_read(APIC_ESR);
2808 apic_write(APIC_LVTERR, apic_pm_state.apic_lvterr);
2809 apic_write(APIC_ESR, 0);
2810 apic_read(APIC_ESR);
2811
2812 irq_remapping_reenable(x2apic_mode);
2813
2814 local_irq_restore(flags);
2815}
2816
2817/*
2818 * This device has no shutdown method - fully functioning local APICs
2819 * are needed on every CPU up until machine_halt/restart/poweroff.
2820 */
2821
2822static struct syscore_ops lapic_syscore_ops = {
2823 .resume = lapic_resume,
2824 .suspend = lapic_suspend,
2825};
2826
2827static void apic_pm_activate(void)
2828{
2829 apic_pm_state.active = 1;
2830}
2831
2832static int __init init_lapic_sysfs(void)
2833{
2834 /* XXX: remove suspend/resume procs if !apic_pm_state.active? */
2835 if (boot_cpu_has(X86_FEATURE_APIC))
2836 register_syscore_ops(&lapic_syscore_ops);
2837
2838 return 0;
2839}
2840
2841/* local apic needs to resume before other devices access its registers. */
2842core_initcall(init_lapic_sysfs);
2843
2844#else /* CONFIG_PM */
2845
2846static void apic_pm_activate(void) { }
2847
2848#endif /* CONFIG_PM */
2849
2850#ifdef CONFIG_X86_64
2851
2852static int multi_checked;
2853static int multi;
2854
2855static int set_multi(const struct dmi_system_id *d)
2856{
2857 if (multi)
2858 return 0;
2859 pr_info("APIC: %s detected, Multi Chassis\n", d->ident);
2860 multi = 1;
2861 return 0;
2862}
2863
2864static const struct dmi_system_id multi_dmi_table[] = {
2865 {
2866 .callback = set_multi,
2867 .ident = "IBM System Summit2",
2868 .matches = {
2869 DMI_MATCH(DMI_SYS_VENDOR, "IBM"),
2870 DMI_MATCH(DMI_PRODUCT_NAME, "Summit2"),
2871 },
2872 },
2873 {}
2874};
2875
2876static void dmi_check_multi(void)
2877{
2878 if (multi_checked)
2879 return;
2880
2881 dmi_check_system(multi_dmi_table);
2882 multi_checked = 1;
2883}
2884
2885/*
2886 * apic_is_clustered_box() -- Check if we can expect good TSC
2887 *
2888 * Thus far, the major user of this is IBM's Summit2 series:
2889 * Clustered boxes may have unsynced TSC problems if they are
2890 * multi-chassis.
2891 * Use DMI to check them
2892 */
2893int apic_is_clustered_box(void)
2894{
2895 dmi_check_multi();
2896 return multi;
2897}
2898#endif
2899
2900/*
2901 * APIC command line parameters
2902 */
2903static int __init setup_disableapic(char *arg)
2904{
2905 disable_apic = 1;
2906 setup_clear_cpu_cap(X86_FEATURE_APIC);
2907 return 0;
2908}
2909early_param("disableapic", setup_disableapic);
2910
2911/* same as disableapic, for compatibility */
2912static int __init setup_nolapic(char *arg)
2913{
2914 return setup_disableapic(arg);
2915}
2916early_param("nolapic", setup_nolapic);
2917
2918static int __init parse_lapic_timer_c2_ok(char *arg)
2919{
2920 local_apic_timer_c2_ok = 1;
2921 return 0;
2922}
2923early_param("lapic_timer_c2_ok", parse_lapic_timer_c2_ok);
2924
2925static int __init parse_disable_apic_timer(char *arg)
2926{
2927 disable_apic_timer = 1;
2928 return 0;
2929}
2930early_param("noapictimer", parse_disable_apic_timer);
2931
2932static int __init parse_nolapic_timer(char *arg)
2933{
2934 disable_apic_timer = 1;
2935 return 0;
2936}
2937early_param("nolapic_timer", parse_nolapic_timer);
2938
2939static int __init apic_set_verbosity(char *arg)
2940{
2941 if (!arg) {
2942#ifdef CONFIG_X86_64
2943 skip_ioapic_setup = 0;
2944 return 0;
2945#endif
2946 return -EINVAL;
2947 }
2948
2949 if (strcmp("debug", arg) == 0)
2950 apic_verbosity = APIC_DEBUG;
2951 else if (strcmp("verbose", arg) == 0)
2952 apic_verbosity = APIC_VERBOSE;
2953#ifdef CONFIG_X86_64
2954 else {
2955 pr_warn("APIC Verbosity level %s not recognised"
2956 " use apic=verbose or apic=debug\n", arg);
2957 return -EINVAL;
2958 }
2959#endif
2960
2961 return 0;
2962}
2963early_param("apic", apic_set_verbosity);
2964
2965static int __init lapic_insert_resource(void)
2966{
2967 if (!apic_phys)
2968 return -1;
2969
2970 /* Put local APIC into the resource map. */
2971 lapic_resource.start = apic_phys;
2972 lapic_resource.end = lapic_resource.start + PAGE_SIZE - 1;
2973 insert_resource(&iomem_resource, &lapic_resource);
2974
2975 return 0;
2976}
2977
2978/*
2979 * need call insert after e820__reserve_resources()
2980 * that is using request_resource
2981 */
2982late_initcall(lapic_insert_resource);
2983
2984static int __init apic_set_disabled_cpu_apicid(char *arg)
2985{
2986 if (!arg || !get_option(&arg, &disabled_cpu_apicid))
2987 return -EINVAL;
2988
2989 return 0;
2990}
2991early_param("disable_cpu_apicid", apic_set_disabled_cpu_apicid);
2992
2993static int __init apic_set_extnmi(char *arg)
2994{
2995 if (!arg)
2996 return -EINVAL;
2997
2998 if (!strncmp("all", arg, 3))
2999 apic_extnmi = APIC_EXTNMI_ALL;
3000 else if (!strncmp("none", arg, 4))
3001 apic_extnmi = APIC_EXTNMI_NONE;
3002 else if (!strncmp("bsp", arg, 3))
3003 apic_extnmi = APIC_EXTNMI_BSP;
3004 else {
3005 pr_warn("Unknown external NMI delivery mode `%s' ignored\n", arg);
3006 return -EINVAL;
3007 }
3008
3009 return 0;
3010}
3011early_param("apic_extnmi", apic_set_extnmi);
1/*
2 * Local APIC handling, local APIC timers
3 *
4 * (c) 1999, 2000, 2009 Ingo Molnar <mingo@redhat.com>
5 *
6 * Fixes
7 * Maciej W. Rozycki : Bits for genuine 82489DX APICs;
8 * thanks to Eric Gilmore
9 * and Rolf G. Tews
10 * for testing these extensively.
11 * Maciej W. Rozycki : Various updates and fixes.
12 * Mikael Pettersson : Power Management for UP-APIC.
13 * Pavel Machek and
14 * Mikael Pettersson : PM converted to driver model.
15 */
16
17#include <linux/perf_event.h>
18#include <linux/kernel_stat.h>
19#include <linux/mc146818rtc.h>
20#include <linux/acpi_pmtmr.h>
21#include <linux/clockchips.h>
22#include <linux/interrupt.h>
23#include <linux/bootmem.h>
24#include <linux/ftrace.h>
25#include <linux/ioport.h>
26#include <linux/module.h>
27#include <linux/syscore_ops.h>
28#include <linux/delay.h>
29#include <linux/timex.h>
30#include <linux/i8253.h>
31#include <linux/dmar.h>
32#include <linux/init.h>
33#include <linux/cpu.h>
34#include <linux/dmi.h>
35#include <linux/smp.h>
36#include <linux/mm.h>
37
38#include <asm/perf_event.h>
39#include <asm/x86_init.h>
40#include <asm/pgalloc.h>
41#include <linux/atomic.h>
42#include <asm/mpspec.h>
43#include <asm/i8259.h>
44#include <asm/proto.h>
45#include <asm/apic.h>
46#include <asm/io_apic.h>
47#include <asm/desc.h>
48#include <asm/hpet.h>
49#include <asm/idle.h>
50#include <asm/mtrr.h>
51#include <asm/time.h>
52#include <asm/smp.h>
53#include <asm/mce.h>
54#include <asm/tsc.h>
55#include <asm/hypervisor.h>
56
57unsigned int num_processors;
58
59unsigned disabled_cpus __cpuinitdata;
60
61/* Processor that is doing the boot up */
62unsigned int boot_cpu_physical_apicid = -1U;
63
64/*
65 * The highest APIC ID seen during enumeration.
66 */
67unsigned int max_physical_apicid;
68
69/*
70 * Bitmask of physically existing CPUs:
71 */
72physid_mask_t phys_cpu_present_map;
73
74/*
75 * Map cpu index to physical APIC ID
76 */
77DEFINE_EARLY_PER_CPU(u16, x86_cpu_to_apicid, BAD_APICID);
78DEFINE_EARLY_PER_CPU(u16, x86_bios_cpu_apicid, BAD_APICID);
79EXPORT_EARLY_PER_CPU_SYMBOL(x86_cpu_to_apicid);
80EXPORT_EARLY_PER_CPU_SYMBOL(x86_bios_cpu_apicid);
81
82#ifdef CONFIG_X86_32
83
84/*
85 * On x86_32, the mapping between cpu and logical apicid may vary
86 * depending on apic in use. The following early percpu variable is
87 * used for the mapping. This is where the behaviors of x86_64 and 32
88 * actually diverge. Let's keep it ugly for now.
89 */
90DEFINE_EARLY_PER_CPU(int, x86_cpu_to_logical_apicid, BAD_APICID);
91
92/*
93 * Knob to control our willingness to enable the local APIC.
94 *
95 * +1=force-enable
96 */
97static int force_enable_local_apic __initdata;
98/*
99 * APIC command line parameters
100 */
101static int __init parse_lapic(char *arg)
102{
103 force_enable_local_apic = 1;
104 return 0;
105}
106early_param("lapic", parse_lapic);
107/* Local APIC was disabled by the BIOS and enabled by the kernel */
108static int enabled_via_apicbase;
109
110/*
111 * Handle interrupt mode configuration register (IMCR).
112 * This register controls whether the interrupt signals
113 * that reach the BSP come from the master PIC or from the
114 * local APIC. Before entering Symmetric I/O Mode, either
115 * the BIOS or the operating system must switch out of
116 * PIC Mode by changing the IMCR.
117 */
118static inline void imcr_pic_to_apic(void)
119{
120 /* select IMCR register */
121 outb(0x70, 0x22);
122 /* NMI and 8259 INTR go through APIC */
123 outb(0x01, 0x23);
124}
125
126static inline void imcr_apic_to_pic(void)
127{
128 /* select IMCR register */
129 outb(0x70, 0x22);
130 /* NMI and 8259 INTR go directly to BSP */
131 outb(0x00, 0x23);
132}
133#endif
134
135#ifdef CONFIG_X86_64
136static int apic_calibrate_pmtmr __initdata;
137static __init int setup_apicpmtimer(char *s)
138{
139 apic_calibrate_pmtmr = 1;
140 notsc_setup(NULL);
141 return 0;
142}
143__setup("apicpmtimer", setup_apicpmtimer);
144#endif
145
146int x2apic_mode;
147#ifdef CONFIG_X86_X2APIC
148/* x2apic enabled before OS handover */
149static int x2apic_preenabled;
150static __init int setup_nox2apic(char *str)
151{
152 if (x2apic_enabled()) {
153 pr_warning("Bios already enabled x2apic, "
154 "can't enforce nox2apic");
155 return 0;
156 }
157
158 setup_clear_cpu_cap(X86_FEATURE_X2APIC);
159 return 0;
160}
161early_param("nox2apic", setup_nox2apic);
162#endif
163
164unsigned long mp_lapic_addr;
165int disable_apic;
166/* Disable local APIC timer from the kernel commandline or via dmi quirk */
167static int disable_apic_timer __initdata;
168/* Local APIC timer works in C2 */
169int local_apic_timer_c2_ok;
170EXPORT_SYMBOL_GPL(local_apic_timer_c2_ok);
171
172int first_system_vector = 0xfe;
173
174/*
175 * Debug level, exported for io_apic.c
176 */
177unsigned int apic_verbosity;
178
179int pic_mode;
180
181/* Have we found an MP table */
182int smp_found_config;
183
184static struct resource lapic_resource = {
185 .name = "Local APIC",
186 .flags = IORESOURCE_MEM | IORESOURCE_BUSY,
187};
188
189static unsigned int calibration_result;
190
191static void apic_pm_activate(void);
192
193static unsigned long apic_phys;
194
195/*
196 * Get the LAPIC version
197 */
198static inline int lapic_get_version(void)
199{
200 return GET_APIC_VERSION(apic_read(APIC_LVR));
201}
202
203/*
204 * Check, if the APIC is integrated or a separate chip
205 */
206static inline int lapic_is_integrated(void)
207{
208#ifdef CONFIG_X86_64
209 return 1;
210#else
211 return APIC_INTEGRATED(lapic_get_version());
212#endif
213}
214
215/*
216 * Check, whether this is a modern or a first generation APIC
217 */
218static int modern_apic(void)
219{
220 /* AMD systems use old APIC versions, so check the CPU */
221 if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD &&
222 boot_cpu_data.x86 >= 0xf)
223 return 1;
224 return lapic_get_version() >= 0x14;
225}
226
227/*
228 * right after this call apic become NOOP driven
229 * so apic->write/read doesn't do anything
230 */
231static void __init apic_disable(void)
232{
233 pr_info("APIC: switched to apic NOOP\n");
234 apic = &apic_noop;
235}
236
237void native_apic_wait_icr_idle(void)
238{
239 while (apic_read(APIC_ICR) & APIC_ICR_BUSY)
240 cpu_relax();
241}
242
243u32 native_safe_apic_wait_icr_idle(void)
244{
245 u32 send_status;
246 int timeout;
247
248 timeout = 0;
249 do {
250 send_status = apic_read(APIC_ICR) & APIC_ICR_BUSY;
251 if (!send_status)
252 break;
253 udelay(100);
254 } while (timeout++ < 1000);
255
256 return send_status;
257}
258
259void native_apic_icr_write(u32 low, u32 id)
260{
261 apic_write(APIC_ICR2, SET_APIC_DEST_FIELD(id));
262 apic_write(APIC_ICR, low);
263}
264
265u64 native_apic_icr_read(void)
266{
267 u32 icr1, icr2;
268
269 icr2 = apic_read(APIC_ICR2);
270 icr1 = apic_read(APIC_ICR);
271
272 return icr1 | ((u64)icr2 << 32);
273}
274
275#ifdef CONFIG_X86_32
276/**
277 * get_physical_broadcast - Get number of physical broadcast IDs
278 */
279int get_physical_broadcast(void)
280{
281 return modern_apic() ? 0xff : 0xf;
282}
283#endif
284
285/**
286 * lapic_get_maxlvt - get the maximum number of local vector table entries
287 */
288int lapic_get_maxlvt(void)
289{
290 unsigned int v;
291
292 v = apic_read(APIC_LVR);
293 /*
294 * - we always have APIC integrated on 64bit mode
295 * - 82489DXs do not report # of LVT entries
296 */
297 return APIC_INTEGRATED(GET_APIC_VERSION(v)) ? GET_APIC_MAXLVT(v) : 2;
298}
299
300/*
301 * Local APIC timer
302 */
303
304/* Clock divisor */
305#define APIC_DIVISOR 16
306
307/*
308 * This function sets up the local APIC timer, with a timeout of
309 * 'clocks' APIC bus clock. During calibration we actually call
310 * this function twice on the boot CPU, once with a bogus timeout
311 * value, second time for real. The other (noncalibrating) CPUs
312 * call this function only once, with the real, calibrated value.
313 *
314 * We do reads before writes even if unnecessary, to get around the
315 * P5 APIC double write bug.
316 */
317static void __setup_APIC_LVTT(unsigned int clocks, int oneshot, int irqen)
318{
319 unsigned int lvtt_value, tmp_value;
320
321 lvtt_value = LOCAL_TIMER_VECTOR;
322 if (!oneshot)
323 lvtt_value |= APIC_LVT_TIMER_PERIODIC;
324 if (!lapic_is_integrated())
325 lvtt_value |= SET_APIC_TIMER_BASE(APIC_TIMER_BASE_DIV);
326
327 if (!irqen)
328 lvtt_value |= APIC_LVT_MASKED;
329
330 apic_write(APIC_LVTT, lvtt_value);
331
332 /*
333 * Divide PICLK by 16
334 */
335 tmp_value = apic_read(APIC_TDCR);
336 apic_write(APIC_TDCR,
337 (tmp_value & ~(APIC_TDR_DIV_1 | APIC_TDR_DIV_TMBASE)) |
338 APIC_TDR_DIV_16);
339
340 if (!oneshot)
341 apic_write(APIC_TMICT, clocks / APIC_DIVISOR);
342}
343
344/*
345 * Setup extended LVT, AMD specific
346 *
347 * Software should use the LVT offsets the BIOS provides. The offsets
348 * are determined by the subsystems using it like those for MCE
349 * threshold or IBS. On K8 only offset 0 (APIC500) and MCE interrupts
350 * are supported. Beginning with family 10h at least 4 offsets are
351 * available.
352 *
353 * Since the offsets must be consistent for all cores, we keep track
354 * of the LVT offsets in software and reserve the offset for the same
355 * vector also to be used on other cores. An offset is freed by
356 * setting the entry to APIC_EILVT_MASKED.
357 *
358 * If the BIOS is right, there should be no conflicts. Otherwise a
359 * "[Firmware Bug]: ..." error message is generated. However, if
360 * software does not properly determines the offsets, it is not
361 * necessarily a BIOS bug.
362 */
363
364static atomic_t eilvt_offsets[APIC_EILVT_NR_MAX];
365
366static inline int eilvt_entry_is_changeable(unsigned int old, unsigned int new)
367{
368 return (old & APIC_EILVT_MASKED)
369 || (new == APIC_EILVT_MASKED)
370 || ((new & ~APIC_EILVT_MASKED) == old);
371}
372
373static unsigned int reserve_eilvt_offset(int offset, unsigned int new)
374{
375 unsigned int rsvd; /* 0: uninitialized */
376
377 if (offset >= APIC_EILVT_NR_MAX)
378 return ~0;
379
380 rsvd = atomic_read(&eilvt_offsets[offset]) & ~APIC_EILVT_MASKED;
381 do {
382 if (rsvd &&
383 !eilvt_entry_is_changeable(rsvd, new))
384 /* may not change if vectors are different */
385 return rsvd;
386 rsvd = atomic_cmpxchg(&eilvt_offsets[offset], rsvd, new);
387 } while (rsvd != new);
388
389 return new;
390}
391
392/*
393 * If mask=1, the LVT entry does not generate interrupts while mask=0
394 * enables the vector. See also the BKDGs. Must be called with
395 * preemption disabled.
396 */
397
398int setup_APIC_eilvt(u8 offset, u8 vector, u8 msg_type, u8 mask)
399{
400 unsigned long reg = APIC_EILVTn(offset);
401 unsigned int new, old, reserved;
402
403 new = (mask << 16) | (msg_type << 8) | vector;
404 old = apic_read(reg);
405 reserved = reserve_eilvt_offset(offset, new);
406
407 if (reserved != new) {
408 pr_err(FW_BUG "cpu %d, try to use APIC%lX (LVT offset %d) for "
409 "vector 0x%x, but the register is already in use for "
410 "vector 0x%x on another cpu\n",
411 smp_processor_id(), reg, offset, new, reserved);
412 return -EINVAL;
413 }
414
415 if (!eilvt_entry_is_changeable(old, new)) {
416 pr_err(FW_BUG "cpu %d, try to use APIC%lX (LVT offset %d) for "
417 "vector 0x%x, but the register is already in use for "
418 "vector 0x%x on this cpu\n",
419 smp_processor_id(), reg, offset, new, old);
420 return -EBUSY;
421 }
422
423 apic_write(reg, new);
424
425 return 0;
426}
427EXPORT_SYMBOL_GPL(setup_APIC_eilvt);
428
429/*
430 * Program the next event, relative to now
431 */
432static int lapic_next_event(unsigned long delta,
433 struct clock_event_device *evt)
434{
435 apic_write(APIC_TMICT, delta);
436 return 0;
437}
438
439/*
440 * Setup the lapic timer in periodic or oneshot mode
441 */
442static void lapic_timer_setup(enum clock_event_mode mode,
443 struct clock_event_device *evt)
444{
445 unsigned long flags;
446 unsigned int v;
447
448 /* Lapic used as dummy for broadcast ? */
449 if (evt->features & CLOCK_EVT_FEAT_DUMMY)
450 return;
451
452 local_irq_save(flags);
453
454 switch (mode) {
455 case CLOCK_EVT_MODE_PERIODIC:
456 case CLOCK_EVT_MODE_ONESHOT:
457 __setup_APIC_LVTT(calibration_result,
458 mode != CLOCK_EVT_MODE_PERIODIC, 1);
459 break;
460 case CLOCK_EVT_MODE_UNUSED:
461 case CLOCK_EVT_MODE_SHUTDOWN:
462 v = apic_read(APIC_LVTT);
463 v |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR);
464 apic_write(APIC_LVTT, v);
465 apic_write(APIC_TMICT, 0);
466 break;
467 case CLOCK_EVT_MODE_RESUME:
468 /* Nothing to do here */
469 break;
470 }
471
472 local_irq_restore(flags);
473}
474
475/*
476 * Local APIC timer broadcast function
477 */
478static void lapic_timer_broadcast(const struct cpumask *mask)
479{
480#ifdef CONFIG_SMP
481 apic->send_IPI_mask(mask, LOCAL_TIMER_VECTOR);
482#endif
483}
484
485
486/*
487 * The local apic timer can be used for any function which is CPU local.
488 */
489static struct clock_event_device lapic_clockevent = {
490 .name = "lapic",
491 .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT
492 | CLOCK_EVT_FEAT_C3STOP | CLOCK_EVT_FEAT_DUMMY,
493 .shift = 32,
494 .set_mode = lapic_timer_setup,
495 .set_next_event = lapic_next_event,
496 .broadcast = lapic_timer_broadcast,
497 .rating = 100,
498 .irq = -1,
499};
500static DEFINE_PER_CPU(struct clock_event_device, lapic_events);
501
502/*
503 * Setup the local APIC timer for this CPU. Copy the initialized values
504 * of the boot CPU and register the clock event in the framework.
505 */
506static void __cpuinit setup_APIC_timer(void)
507{
508 struct clock_event_device *levt = &__get_cpu_var(lapic_events);
509
510 if (this_cpu_has(X86_FEATURE_ARAT)) {
511 lapic_clockevent.features &= ~CLOCK_EVT_FEAT_C3STOP;
512 /* Make LAPIC timer preferrable over percpu HPET */
513 lapic_clockevent.rating = 150;
514 }
515
516 memcpy(levt, &lapic_clockevent, sizeof(*levt));
517 levt->cpumask = cpumask_of(smp_processor_id());
518
519 clockevents_register_device(levt);
520}
521
522/*
523 * In this functions we calibrate APIC bus clocks to the external timer.
524 *
525 * We want to do the calibration only once since we want to have local timer
526 * irqs syncron. CPUs connected by the same APIC bus have the very same bus
527 * frequency.
528 *
529 * This was previously done by reading the PIT/HPET and waiting for a wrap
530 * around to find out, that a tick has elapsed. I have a box, where the PIT
531 * readout is broken, so it never gets out of the wait loop again. This was
532 * also reported by others.
533 *
534 * Monitoring the jiffies value is inaccurate and the clockevents
535 * infrastructure allows us to do a simple substitution of the interrupt
536 * handler.
537 *
538 * The calibration routine also uses the pm_timer when possible, as the PIT
539 * happens to run way too slow (factor 2.3 on my VAIO CoreDuo, which goes
540 * back to normal later in the boot process).
541 */
542
543#define LAPIC_CAL_LOOPS (HZ/10)
544
545static __initdata int lapic_cal_loops = -1;
546static __initdata long lapic_cal_t1, lapic_cal_t2;
547static __initdata unsigned long long lapic_cal_tsc1, lapic_cal_tsc2;
548static __initdata unsigned long lapic_cal_pm1, lapic_cal_pm2;
549static __initdata unsigned long lapic_cal_j1, lapic_cal_j2;
550
551/*
552 * Temporary interrupt handler.
553 */
554static void __init lapic_cal_handler(struct clock_event_device *dev)
555{
556 unsigned long long tsc = 0;
557 long tapic = apic_read(APIC_TMCCT);
558 unsigned long pm = acpi_pm_read_early();
559
560 if (cpu_has_tsc)
561 rdtscll(tsc);
562
563 switch (lapic_cal_loops++) {
564 case 0:
565 lapic_cal_t1 = tapic;
566 lapic_cal_tsc1 = tsc;
567 lapic_cal_pm1 = pm;
568 lapic_cal_j1 = jiffies;
569 break;
570
571 case LAPIC_CAL_LOOPS:
572 lapic_cal_t2 = tapic;
573 lapic_cal_tsc2 = tsc;
574 if (pm < lapic_cal_pm1)
575 pm += ACPI_PM_OVRRUN;
576 lapic_cal_pm2 = pm;
577 lapic_cal_j2 = jiffies;
578 break;
579 }
580}
581
582static int __init
583calibrate_by_pmtimer(long deltapm, long *delta, long *deltatsc)
584{
585 const long pm_100ms = PMTMR_TICKS_PER_SEC / 10;
586 const long pm_thresh = pm_100ms / 100;
587 unsigned long mult;
588 u64 res;
589
590#ifndef CONFIG_X86_PM_TIMER
591 return -1;
592#endif
593
594 apic_printk(APIC_VERBOSE, "... PM-Timer delta = %ld\n", deltapm);
595
596 /* Check, if the PM timer is available */
597 if (!deltapm)
598 return -1;
599
600 mult = clocksource_hz2mult(PMTMR_TICKS_PER_SEC, 22);
601
602 if (deltapm > (pm_100ms - pm_thresh) &&
603 deltapm < (pm_100ms + pm_thresh)) {
604 apic_printk(APIC_VERBOSE, "... PM-Timer result ok\n");
605 return 0;
606 }
607
608 res = (((u64)deltapm) * mult) >> 22;
609 do_div(res, 1000000);
610 pr_warning("APIC calibration not consistent "
611 "with PM-Timer: %ldms instead of 100ms\n",(long)res);
612
613 /* Correct the lapic counter value */
614 res = (((u64)(*delta)) * pm_100ms);
615 do_div(res, deltapm);
616 pr_info("APIC delta adjusted to PM-Timer: "
617 "%lu (%ld)\n", (unsigned long)res, *delta);
618 *delta = (long)res;
619
620 /* Correct the tsc counter value */
621 if (cpu_has_tsc) {
622 res = (((u64)(*deltatsc)) * pm_100ms);
623 do_div(res, deltapm);
624 apic_printk(APIC_VERBOSE, "TSC delta adjusted to "
625 "PM-Timer: %lu (%ld)\n",
626 (unsigned long)res, *deltatsc);
627 *deltatsc = (long)res;
628 }
629
630 return 0;
631}
632
633static int __init calibrate_APIC_clock(void)
634{
635 struct clock_event_device *levt = &__get_cpu_var(lapic_events);
636 void (*real_handler)(struct clock_event_device *dev);
637 unsigned long deltaj;
638 long delta, deltatsc;
639 int pm_referenced = 0;
640
641 local_irq_disable();
642
643 /* Replace the global interrupt handler */
644 real_handler = global_clock_event->event_handler;
645 global_clock_event->event_handler = lapic_cal_handler;
646
647 /*
648 * Setup the APIC counter to maximum. There is no way the lapic
649 * can underflow in the 100ms detection time frame
650 */
651 __setup_APIC_LVTT(0xffffffff, 0, 0);
652
653 /* Let the interrupts run */
654 local_irq_enable();
655
656 while (lapic_cal_loops <= LAPIC_CAL_LOOPS)
657 cpu_relax();
658
659 local_irq_disable();
660
661 /* Restore the real event handler */
662 global_clock_event->event_handler = real_handler;
663
664 /* Build delta t1-t2 as apic timer counts down */
665 delta = lapic_cal_t1 - lapic_cal_t2;
666 apic_printk(APIC_VERBOSE, "... lapic delta = %ld\n", delta);
667
668 deltatsc = (long)(lapic_cal_tsc2 - lapic_cal_tsc1);
669
670 /* we trust the PM based calibration if possible */
671 pm_referenced = !calibrate_by_pmtimer(lapic_cal_pm2 - lapic_cal_pm1,
672 &delta, &deltatsc);
673
674 /* Calculate the scaled math multiplication factor */
675 lapic_clockevent.mult = div_sc(delta, TICK_NSEC * LAPIC_CAL_LOOPS,
676 lapic_clockevent.shift);
677 lapic_clockevent.max_delta_ns =
678 clockevent_delta2ns(0x7FFFFFFF, &lapic_clockevent);
679 lapic_clockevent.min_delta_ns =
680 clockevent_delta2ns(0xF, &lapic_clockevent);
681
682 calibration_result = (delta * APIC_DIVISOR) / LAPIC_CAL_LOOPS;
683
684 apic_printk(APIC_VERBOSE, "..... delta %ld\n", delta);
685 apic_printk(APIC_VERBOSE, "..... mult: %u\n", lapic_clockevent.mult);
686 apic_printk(APIC_VERBOSE, "..... calibration result: %u\n",
687 calibration_result);
688
689 if (cpu_has_tsc) {
690 apic_printk(APIC_VERBOSE, "..... CPU clock speed is "
691 "%ld.%04ld MHz.\n",
692 (deltatsc / LAPIC_CAL_LOOPS) / (1000000 / HZ),
693 (deltatsc / LAPIC_CAL_LOOPS) % (1000000 / HZ));
694 }
695
696 apic_printk(APIC_VERBOSE, "..... host bus clock speed is "
697 "%u.%04u MHz.\n",
698 calibration_result / (1000000 / HZ),
699 calibration_result % (1000000 / HZ));
700
701 /*
702 * Do a sanity check on the APIC calibration result
703 */
704 if (calibration_result < (1000000 / HZ)) {
705 local_irq_enable();
706 pr_warning("APIC frequency too slow, disabling apic timer\n");
707 return -1;
708 }
709
710 levt->features &= ~CLOCK_EVT_FEAT_DUMMY;
711
712 /*
713 * PM timer calibration failed or not turned on
714 * so lets try APIC timer based calibration
715 */
716 if (!pm_referenced) {
717 apic_printk(APIC_VERBOSE, "... verify APIC timer\n");
718
719 /*
720 * Setup the apic timer manually
721 */
722 levt->event_handler = lapic_cal_handler;
723 lapic_timer_setup(CLOCK_EVT_MODE_PERIODIC, levt);
724 lapic_cal_loops = -1;
725
726 /* Let the interrupts run */
727 local_irq_enable();
728
729 while (lapic_cal_loops <= LAPIC_CAL_LOOPS)
730 cpu_relax();
731
732 /* Stop the lapic timer */
733 lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, levt);
734
735 /* Jiffies delta */
736 deltaj = lapic_cal_j2 - lapic_cal_j1;
737 apic_printk(APIC_VERBOSE, "... jiffies delta = %lu\n", deltaj);
738
739 /* Check, if the jiffies result is consistent */
740 if (deltaj >= LAPIC_CAL_LOOPS-2 && deltaj <= LAPIC_CAL_LOOPS+2)
741 apic_printk(APIC_VERBOSE, "... jiffies result ok\n");
742 else
743 levt->features |= CLOCK_EVT_FEAT_DUMMY;
744 } else
745 local_irq_enable();
746
747 if (levt->features & CLOCK_EVT_FEAT_DUMMY) {
748 pr_warning("APIC timer disabled due to verification failure\n");
749 return -1;
750 }
751
752 return 0;
753}
754
755/*
756 * Setup the boot APIC
757 *
758 * Calibrate and verify the result.
759 */
760void __init setup_boot_APIC_clock(void)
761{
762 /*
763 * The local apic timer can be disabled via the kernel
764 * commandline or from the CPU detection code. Register the lapic
765 * timer as a dummy clock event source on SMP systems, so the
766 * broadcast mechanism is used. On UP systems simply ignore it.
767 */
768 if (disable_apic_timer) {
769 pr_info("Disabling APIC timer\n");
770 /* No broadcast on UP ! */
771 if (num_possible_cpus() > 1) {
772 lapic_clockevent.mult = 1;
773 setup_APIC_timer();
774 }
775 return;
776 }
777
778 apic_printk(APIC_VERBOSE, "Using local APIC timer interrupts.\n"
779 "calibrating APIC timer ...\n");
780
781 if (calibrate_APIC_clock()) {
782 /* No broadcast on UP ! */
783 if (num_possible_cpus() > 1)
784 setup_APIC_timer();
785 return;
786 }
787
788 /*
789 * If nmi_watchdog is set to IO_APIC, we need the
790 * PIT/HPET going. Otherwise register lapic as a dummy
791 * device.
792 */
793 lapic_clockevent.features &= ~CLOCK_EVT_FEAT_DUMMY;
794
795 /* Setup the lapic or request the broadcast */
796 setup_APIC_timer();
797}
798
799void __cpuinit setup_secondary_APIC_clock(void)
800{
801 setup_APIC_timer();
802}
803
804/*
805 * The guts of the apic timer interrupt
806 */
807static void local_apic_timer_interrupt(void)
808{
809 int cpu = smp_processor_id();
810 struct clock_event_device *evt = &per_cpu(lapic_events, cpu);
811
812 /*
813 * Normally we should not be here till LAPIC has been initialized but
814 * in some cases like kdump, its possible that there is a pending LAPIC
815 * timer interrupt from previous kernel's context and is delivered in
816 * new kernel the moment interrupts are enabled.
817 *
818 * Interrupts are enabled early and LAPIC is setup much later, hence
819 * its possible that when we get here evt->event_handler is NULL.
820 * Check for event_handler being NULL and discard the interrupt as
821 * spurious.
822 */
823 if (!evt->event_handler) {
824 pr_warning("Spurious LAPIC timer interrupt on cpu %d\n", cpu);
825 /* Switch it off */
826 lapic_timer_setup(CLOCK_EVT_MODE_SHUTDOWN, evt);
827 return;
828 }
829
830 /*
831 * the NMI deadlock-detector uses this.
832 */
833 inc_irq_stat(apic_timer_irqs);
834
835 evt->event_handler(evt);
836}
837
838/*
839 * Local APIC timer interrupt. This is the most natural way for doing
840 * local interrupts, but local timer interrupts can be emulated by
841 * broadcast interrupts too. [in case the hw doesn't support APIC timers]
842 *
843 * [ if a single-CPU system runs an SMP kernel then we call the local
844 * interrupt as well. Thus we cannot inline the local irq ... ]
845 */
846void __irq_entry smp_apic_timer_interrupt(struct pt_regs *regs)
847{
848 struct pt_regs *old_regs = set_irq_regs(regs);
849
850 /*
851 * NOTE! We'd better ACK the irq immediately,
852 * because timer handling can be slow.
853 */
854 ack_APIC_irq();
855 /*
856 * update_process_times() expects us to have done irq_enter().
857 * Besides, if we don't timer interrupts ignore the global
858 * interrupt lock, which is the WrongThing (tm) to do.
859 */
860 exit_idle();
861 irq_enter();
862 local_apic_timer_interrupt();
863 irq_exit();
864
865 set_irq_regs(old_regs);
866}
867
868int setup_profiling_timer(unsigned int multiplier)
869{
870 return -EINVAL;
871}
872
873/*
874 * Local APIC start and shutdown
875 */
876
877/**
878 * clear_local_APIC - shutdown the local APIC
879 *
880 * This is called, when a CPU is disabled and before rebooting, so the state of
881 * the local APIC has no dangling leftovers. Also used to cleanout any BIOS
882 * leftovers during boot.
883 */
884void clear_local_APIC(void)
885{
886 int maxlvt;
887 u32 v;
888
889 /* APIC hasn't been mapped yet */
890 if (!x2apic_mode && !apic_phys)
891 return;
892
893 maxlvt = lapic_get_maxlvt();
894 /*
895 * Masking an LVT entry can trigger a local APIC error
896 * if the vector is zero. Mask LVTERR first to prevent this.
897 */
898 if (maxlvt >= 3) {
899 v = ERROR_APIC_VECTOR; /* any non-zero vector will do */
900 apic_write(APIC_LVTERR, v | APIC_LVT_MASKED);
901 }
902 /*
903 * Careful: we have to set masks only first to deassert
904 * any level-triggered sources.
905 */
906 v = apic_read(APIC_LVTT);
907 apic_write(APIC_LVTT, v | APIC_LVT_MASKED);
908 v = apic_read(APIC_LVT0);
909 apic_write(APIC_LVT0, v | APIC_LVT_MASKED);
910 v = apic_read(APIC_LVT1);
911 apic_write(APIC_LVT1, v | APIC_LVT_MASKED);
912 if (maxlvt >= 4) {
913 v = apic_read(APIC_LVTPC);
914 apic_write(APIC_LVTPC, v | APIC_LVT_MASKED);
915 }
916
917 /* lets not touch this if we didn't frob it */
918#ifdef CONFIG_X86_THERMAL_VECTOR
919 if (maxlvt >= 5) {
920 v = apic_read(APIC_LVTTHMR);
921 apic_write(APIC_LVTTHMR, v | APIC_LVT_MASKED);
922 }
923#endif
924#ifdef CONFIG_X86_MCE_INTEL
925 if (maxlvt >= 6) {
926 v = apic_read(APIC_LVTCMCI);
927 if (!(v & APIC_LVT_MASKED))
928 apic_write(APIC_LVTCMCI, v | APIC_LVT_MASKED);
929 }
930#endif
931
932 /*
933 * Clean APIC state for other OSs:
934 */
935 apic_write(APIC_LVTT, APIC_LVT_MASKED);
936 apic_write(APIC_LVT0, APIC_LVT_MASKED);
937 apic_write(APIC_LVT1, APIC_LVT_MASKED);
938 if (maxlvt >= 3)
939 apic_write(APIC_LVTERR, APIC_LVT_MASKED);
940 if (maxlvt >= 4)
941 apic_write(APIC_LVTPC, APIC_LVT_MASKED);
942
943 /* Integrated APIC (!82489DX) ? */
944 if (lapic_is_integrated()) {
945 if (maxlvt > 3)
946 /* Clear ESR due to Pentium errata 3AP and 11AP */
947 apic_write(APIC_ESR, 0);
948 apic_read(APIC_ESR);
949 }
950}
951
952/**
953 * disable_local_APIC - clear and disable the local APIC
954 */
955void disable_local_APIC(void)
956{
957 unsigned int value;
958
959 /* APIC hasn't been mapped yet */
960 if (!x2apic_mode && !apic_phys)
961 return;
962
963 clear_local_APIC();
964
965 /*
966 * Disable APIC (implies clearing of registers
967 * for 82489DX!).
968 */
969 value = apic_read(APIC_SPIV);
970 value &= ~APIC_SPIV_APIC_ENABLED;
971 apic_write(APIC_SPIV, value);
972
973#ifdef CONFIG_X86_32
974 /*
975 * When LAPIC was disabled by the BIOS and enabled by the kernel,
976 * restore the disabled state.
977 */
978 if (enabled_via_apicbase) {
979 unsigned int l, h;
980
981 rdmsr(MSR_IA32_APICBASE, l, h);
982 l &= ~MSR_IA32_APICBASE_ENABLE;
983 wrmsr(MSR_IA32_APICBASE, l, h);
984 }
985#endif
986}
987
988/*
989 * If Linux enabled the LAPIC against the BIOS default disable it down before
990 * re-entering the BIOS on shutdown. Otherwise the BIOS may get confused and
991 * not power-off. Additionally clear all LVT entries before disable_local_APIC
992 * for the case where Linux didn't enable the LAPIC.
993 */
994void lapic_shutdown(void)
995{
996 unsigned long flags;
997
998 if (!cpu_has_apic && !apic_from_smp_config())
999 return;
1000
1001 local_irq_save(flags);
1002
1003#ifdef CONFIG_X86_32
1004 if (!enabled_via_apicbase)
1005 clear_local_APIC();
1006 else
1007#endif
1008 disable_local_APIC();
1009
1010
1011 local_irq_restore(flags);
1012}
1013
1014/*
1015 * This is to verify that we're looking at a real local APIC.
1016 * Check these against your board if the CPUs aren't getting
1017 * started for no apparent reason.
1018 */
1019int __init verify_local_APIC(void)
1020{
1021 unsigned int reg0, reg1;
1022
1023 /*
1024 * The version register is read-only in a real APIC.
1025 */
1026 reg0 = apic_read(APIC_LVR);
1027 apic_printk(APIC_DEBUG, "Getting VERSION: %x\n", reg0);
1028 apic_write(APIC_LVR, reg0 ^ APIC_LVR_MASK);
1029 reg1 = apic_read(APIC_LVR);
1030 apic_printk(APIC_DEBUG, "Getting VERSION: %x\n", reg1);
1031
1032 /*
1033 * The two version reads above should print the same
1034 * numbers. If the second one is different, then we
1035 * poke at a non-APIC.
1036 */
1037 if (reg1 != reg0)
1038 return 0;
1039
1040 /*
1041 * Check if the version looks reasonably.
1042 */
1043 reg1 = GET_APIC_VERSION(reg0);
1044 if (reg1 == 0x00 || reg1 == 0xff)
1045 return 0;
1046 reg1 = lapic_get_maxlvt();
1047 if (reg1 < 0x02 || reg1 == 0xff)
1048 return 0;
1049
1050 /*
1051 * The ID register is read/write in a real APIC.
1052 */
1053 reg0 = apic_read(APIC_ID);
1054 apic_printk(APIC_DEBUG, "Getting ID: %x\n", reg0);
1055 apic_write(APIC_ID, reg0 ^ apic->apic_id_mask);
1056 reg1 = apic_read(APIC_ID);
1057 apic_printk(APIC_DEBUG, "Getting ID: %x\n", reg1);
1058 apic_write(APIC_ID, reg0);
1059 if (reg1 != (reg0 ^ apic->apic_id_mask))
1060 return 0;
1061
1062 /*
1063 * The next two are just to see if we have sane values.
1064 * They're only really relevant if we're in Virtual Wire
1065 * compatibility mode, but most boxes are anymore.
1066 */
1067 reg0 = apic_read(APIC_LVT0);
1068 apic_printk(APIC_DEBUG, "Getting LVT0: %x\n", reg0);
1069 reg1 = apic_read(APIC_LVT1);
1070 apic_printk(APIC_DEBUG, "Getting LVT1: %x\n", reg1);
1071
1072 return 1;
1073}
1074
1075/**
1076 * sync_Arb_IDs - synchronize APIC bus arbitration IDs
1077 */
1078void __init sync_Arb_IDs(void)
1079{
1080 /*
1081 * Unsupported on P4 - see Intel Dev. Manual Vol. 3, Ch. 8.6.1 And not
1082 * needed on AMD.
1083 */
1084 if (modern_apic() || boot_cpu_data.x86_vendor == X86_VENDOR_AMD)
1085 return;
1086
1087 /*
1088 * Wait for idle.
1089 */
1090 apic_wait_icr_idle();
1091
1092 apic_printk(APIC_DEBUG, "Synchronizing Arb IDs.\n");
1093 apic_write(APIC_ICR, APIC_DEST_ALLINC |
1094 APIC_INT_LEVELTRIG | APIC_DM_INIT);
1095}
1096
1097/*
1098 * An initial setup of the virtual wire mode.
1099 */
1100void __init init_bsp_APIC(void)
1101{
1102 unsigned int value;
1103
1104 /*
1105 * Don't do the setup now if we have a SMP BIOS as the
1106 * through-I/O-APIC virtual wire mode might be active.
1107 */
1108 if (smp_found_config || !cpu_has_apic)
1109 return;
1110
1111 /*
1112 * Do not trust the local APIC being empty at bootup.
1113 */
1114 clear_local_APIC();
1115
1116 /*
1117 * Enable APIC.
1118 */
1119 value = apic_read(APIC_SPIV);
1120 value &= ~APIC_VECTOR_MASK;
1121 value |= APIC_SPIV_APIC_ENABLED;
1122
1123#ifdef CONFIG_X86_32
1124 /* This bit is reserved on P4/Xeon and should be cleared */
1125 if ((boot_cpu_data.x86_vendor == X86_VENDOR_INTEL) &&
1126 (boot_cpu_data.x86 == 15))
1127 value &= ~APIC_SPIV_FOCUS_DISABLED;
1128 else
1129#endif
1130 value |= APIC_SPIV_FOCUS_DISABLED;
1131 value |= SPURIOUS_APIC_VECTOR;
1132 apic_write(APIC_SPIV, value);
1133
1134 /*
1135 * Set up the virtual wire mode.
1136 */
1137 apic_write(APIC_LVT0, APIC_DM_EXTINT);
1138 value = APIC_DM_NMI;
1139 if (!lapic_is_integrated()) /* 82489DX */
1140 value |= APIC_LVT_LEVEL_TRIGGER;
1141 apic_write(APIC_LVT1, value);
1142}
1143
1144static void __cpuinit lapic_setup_esr(void)
1145{
1146 unsigned int oldvalue, value, maxlvt;
1147
1148 if (!lapic_is_integrated()) {
1149 pr_info("No ESR for 82489DX.\n");
1150 return;
1151 }
1152
1153 if (apic->disable_esr) {
1154 /*
1155 * Something untraceable is creating bad interrupts on
1156 * secondary quads ... for the moment, just leave the
1157 * ESR disabled - we can't do anything useful with the
1158 * errors anyway - mbligh
1159 */
1160 pr_info("Leaving ESR disabled.\n");
1161 return;
1162 }
1163
1164 maxlvt = lapic_get_maxlvt();
1165 if (maxlvt > 3) /* Due to the Pentium erratum 3AP. */
1166 apic_write(APIC_ESR, 0);
1167 oldvalue = apic_read(APIC_ESR);
1168
1169 /* enables sending errors */
1170 value = ERROR_APIC_VECTOR;
1171 apic_write(APIC_LVTERR, value);
1172
1173 /*
1174 * spec says clear errors after enabling vector.
1175 */
1176 if (maxlvt > 3)
1177 apic_write(APIC_ESR, 0);
1178 value = apic_read(APIC_ESR);
1179 if (value != oldvalue)
1180 apic_printk(APIC_VERBOSE, "ESR value before enabling "
1181 "vector: 0x%08x after: 0x%08x\n",
1182 oldvalue, value);
1183}
1184
1185/**
1186 * setup_local_APIC - setup the local APIC
1187 *
1188 * Used to setup local APIC while initializing BSP or bringin up APs.
1189 * Always called with preemption disabled.
1190 */
1191void __cpuinit setup_local_APIC(void)
1192{
1193 int cpu = smp_processor_id();
1194 unsigned int value, queued;
1195 int i, j, acked = 0;
1196 unsigned long long tsc = 0, ntsc;
1197 long long max_loops = cpu_khz;
1198
1199 if (cpu_has_tsc)
1200 rdtscll(tsc);
1201
1202 if (disable_apic) {
1203 disable_ioapic_support();
1204 return;
1205 }
1206
1207#ifdef CONFIG_X86_32
1208 /* Pound the ESR really hard over the head with a big hammer - mbligh */
1209 if (lapic_is_integrated() && apic->disable_esr) {
1210 apic_write(APIC_ESR, 0);
1211 apic_write(APIC_ESR, 0);
1212 apic_write(APIC_ESR, 0);
1213 apic_write(APIC_ESR, 0);
1214 }
1215#endif
1216 perf_events_lapic_init();
1217
1218 /*
1219 * Double-check whether this APIC is really registered.
1220 * This is meaningless in clustered apic mode, so we skip it.
1221 */
1222 BUG_ON(!apic->apic_id_registered());
1223
1224 /*
1225 * Intel recommends to set DFR, LDR and TPR before enabling
1226 * an APIC. See e.g. "AP-388 82489DX User's Manual" (Intel
1227 * document number 292116). So here it goes...
1228 */
1229 apic->init_apic_ldr();
1230
1231#ifdef CONFIG_X86_32
1232 /*
1233 * APIC LDR is initialized. If logical_apicid mapping was
1234 * initialized during get_smp_config(), make sure it matches the
1235 * actual value.
1236 */
1237 i = early_per_cpu(x86_cpu_to_logical_apicid, cpu);
1238 WARN_ON(i != BAD_APICID && i != logical_smp_processor_id());
1239 /* always use the value from LDR */
1240 early_per_cpu(x86_cpu_to_logical_apicid, cpu) =
1241 logical_smp_processor_id();
1242
1243 /*
1244 * Some NUMA implementations (NUMAQ) don't initialize apicid to
1245 * node mapping during NUMA init. Now that logical apicid is
1246 * guaranteed to be known, give it another chance. This is already
1247 * a bit too late - percpu allocation has already happened without
1248 * proper NUMA affinity.
1249 */
1250 if (apic->x86_32_numa_cpu_node)
1251 set_apicid_to_node(early_per_cpu(x86_cpu_to_apicid, cpu),
1252 apic->x86_32_numa_cpu_node(cpu));
1253#endif
1254
1255 /*
1256 * Set Task Priority to 'accept all'. We never change this
1257 * later on.
1258 */
1259 value = apic_read(APIC_TASKPRI);
1260 value &= ~APIC_TPRI_MASK;
1261 apic_write(APIC_TASKPRI, value);
1262
1263 /*
1264 * After a crash, we no longer service the interrupts and a pending
1265 * interrupt from previous kernel might still have ISR bit set.
1266 *
1267 * Most probably by now CPU has serviced that pending interrupt and
1268 * it might not have done the ack_APIC_irq() because it thought,
1269 * interrupt came from i8259 as ExtInt. LAPIC did not get EOI so it
1270 * does not clear the ISR bit and cpu thinks it has already serivced
1271 * the interrupt. Hence a vector might get locked. It was noticed
1272 * for timer irq (vector 0x31). Issue an extra EOI to clear ISR.
1273 */
1274 do {
1275 queued = 0;
1276 for (i = APIC_ISR_NR - 1; i >= 0; i--)
1277 queued |= apic_read(APIC_IRR + i*0x10);
1278
1279 for (i = APIC_ISR_NR - 1; i >= 0; i--) {
1280 value = apic_read(APIC_ISR + i*0x10);
1281 for (j = 31; j >= 0; j--) {
1282 if (value & (1<<j)) {
1283 ack_APIC_irq();
1284 acked++;
1285 }
1286 }
1287 }
1288 if (acked > 256) {
1289 printk(KERN_ERR "LAPIC pending interrupts after %d EOI\n",
1290 acked);
1291 break;
1292 }
1293 if (cpu_has_tsc) {
1294 rdtscll(ntsc);
1295 max_loops = (cpu_khz << 10) - (ntsc - tsc);
1296 } else
1297 max_loops--;
1298 } while (queued && max_loops > 0);
1299 WARN_ON(max_loops <= 0);
1300
1301 /*
1302 * Now that we are all set up, enable the APIC
1303 */
1304 value = apic_read(APIC_SPIV);
1305 value &= ~APIC_VECTOR_MASK;
1306 /*
1307 * Enable APIC
1308 */
1309 value |= APIC_SPIV_APIC_ENABLED;
1310
1311#ifdef CONFIG_X86_32
1312 /*
1313 * Some unknown Intel IO/APIC (or APIC) errata is biting us with
1314 * certain networking cards. If high frequency interrupts are
1315 * happening on a particular IOAPIC pin, plus the IOAPIC routing
1316 * entry is masked/unmasked at a high rate as well then sooner or
1317 * later IOAPIC line gets 'stuck', no more interrupts are received
1318 * from the device. If focus CPU is disabled then the hang goes
1319 * away, oh well :-(
1320 *
1321 * [ This bug can be reproduced easily with a level-triggered
1322 * PCI Ne2000 networking cards and PII/PIII processors, dual
1323 * BX chipset. ]
1324 */
1325 /*
1326 * Actually disabling the focus CPU check just makes the hang less
1327 * frequent as it makes the interrupt distributon model be more
1328 * like LRU than MRU (the short-term load is more even across CPUs).
1329 * See also the comment in end_level_ioapic_irq(). --macro
1330 */
1331
1332 /*
1333 * - enable focus processor (bit==0)
1334 * - 64bit mode always use processor focus
1335 * so no need to set it
1336 */
1337 value &= ~APIC_SPIV_FOCUS_DISABLED;
1338#endif
1339
1340 /*
1341 * Set spurious IRQ vector
1342 */
1343 value |= SPURIOUS_APIC_VECTOR;
1344 apic_write(APIC_SPIV, value);
1345
1346 /*
1347 * Set up LVT0, LVT1:
1348 *
1349 * set up through-local-APIC on the BP's LINT0. This is not
1350 * strictly necessary in pure symmetric-IO mode, but sometimes
1351 * we delegate interrupts to the 8259A.
1352 */
1353 /*
1354 * TODO: set up through-local-APIC from through-I/O-APIC? --macro
1355 */
1356 value = apic_read(APIC_LVT0) & APIC_LVT_MASKED;
1357 if (!cpu && (pic_mode || !value)) {
1358 value = APIC_DM_EXTINT;
1359 apic_printk(APIC_VERBOSE, "enabled ExtINT on CPU#%d\n", cpu);
1360 } else {
1361 value = APIC_DM_EXTINT | APIC_LVT_MASKED;
1362 apic_printk(APIC_VERBOSE, "masked ExtINT on CPU#%d\n", cpu);
1363 }
1364 apic_write(APIC_LVT0, value);
1365
1366 /*
1367 * only the BP should see the LINT1 NMI signal, obviously.
1368 */
1369 if (!cpu)
1370 value = APIC_DM_NMI;
1371 else
1372 value = APIC_DM_NMI | APIC_LVT_MASKED;
1373 if (!lapic_is_integrated()) /* 82489DX */
1374 value |= APIC_LVT_LEVEL_TRIGGER;
1375 apic_write(APIC_LVT1, value);
1376
1377#ifdef CONFIG_X86_MCE_INTEL
1378 /* Recheck CMCI information after local APIC is up on CPU #0 */
1379 if (!cpu)
1380 cmci_recheck();
1381#endif
1382}
1383
1384void __cpuinit end_local_APIC_setup(void)
1385{
1386 lapic_setup_esr();
1387
1388#ifdef CONFIG_X86_32
1389 {
1390 unsigned int value;
1391 /* Disable the local apic timer */
1392 value = apic_read(APIC_LVTT);
1393 value |= (APIC_LVT_MASKED | LOCAL_TIMER_VECTOR);
1394 apic_write(APIC_LVTT, value);
1395 }
1396#endif
1397
1398 apic_pm_activate();
1399}
1400
1401void __init bsp_end_local_APIC_setup(void)
1402{
1403 end_local_APIC_setup();
1404
1405 /*
1406 * Now that local APIC setup is completed for BP, configure the fault
1407 * handling for interrupt remapping.
1408 */
1409 if (intr_remapping_enabled)
1410 enable_drhd_fault_handling();
1411
1412}
1413
1414#ifdef CONFIG_X86_X2APIC
1415void check_x2apic(void)
1416{
1417 if (x2apic_enabled()) {
1418 pr_info("x2apic enabled by BIOS, switching to x2apic ops\n");
1419 x2apic_preenabled = x2apic_mode = 1;
1420 }
1421}
1422
1423void enable_x2apic(void)
1424{
1425 int msr, msr2;
1426
1427 if (!x2apic_mode)
1428 return;
1429
1430 rdmsr(MSR_IA32_APICBASE, msr, msr2);
1431 if (!(msr & X2APIC_ENABLE)) {
1432 printk_once(KERN_INFO "Enabling x2apic\n");
1433 wrmsr(MSR_IA32_APICBASE, msr | X2APIC_ENABLE, msr2);
1434 }
1435}
1436#endif /* CONFIG_X86_X2APIC */
1437
1438int __init enable_IR(void)
1439{
1440#ifdef CONFIG_INTR_REMAP
1441 if (!intr_remapping_supported()) {
1442 pr_debug("intr-remapping not supported\n");
1443 return 0;
1444 }
1445
1446 if (!x2apic_preenabled && skip_ioapic_setup) {
1447 pr_info("Skipped enabling intr-remap because of skipping "
1448 "io-apic setup\n");
1449 return 0;
1450 }
1451
1452 if (enable_intr_remapping(x2apic_supported()))
1453 return 0;
1454
1455 pr_info("Enabled Interrupt-remapping\n");
1456
1457 return 1;
1458
1459#endif
1460 return 0;
1461}
1462
1463void __init enable_IR_x2apic(void)
1464{
1465 unsigned long flags;
1466 int ret, x2apic_enabled = 0;
1467 int dmar_table_init_ret;
1468
1469 dmar_table_init_ret = dmar_table_init();
1470 if (dmar_table_init_ret && !x2apic_supported())
1471 return;
1472
1473 ret = save_ioapic_entries();
1474 if (ret) {
1475 pr_info("Saving IO-APIC state failed: %d\n", ret);
1476 goto out;
1477 }
1478
1479 local_irq_save(flags);
1480 legacy_pic->mask_all();
1481 mask_ioapic_entries();
1482
1483 if (dmar_table_init_ret)
1484 ret = 0;
1485 else
1486 ret = enable_IR();
1487
1488 if (!ret) {
1489 /* IR is required if there is APIC ID > 255 even when running
1490 * under KVM
1491 */
1492 if (max_physical_apicid > 255 ||
1493 !hypervisor_x2apic_available())
1494 goto nox2apic;
1495 /*
1496 * without IR all CPUs can be addressed by IOAPIC/MSI
1497 * only in physical mode
1498 */
1499 x2apic_force_phys();
1500 }
1501
1502 x2apic_enabled = 1;
1503
1504 if (x2apic_supported() && !x2apic_mode) {
1505 x2apic_mode = 1;
1506 enable_x2apic();
1507 pr_info("Enabled x2apic\n");
1508 }
1509
1510nox2apic:
1511 if (!ret) /* IR enabling failed */
1512 restore_ioapic_entries();
1513 legacy_pic->restore_mask();
1514 local_irq_restore(flags);
1515
1516out:
1517 if (x2apic_enabled)
1518 return;
1519
1520 if (x2apic_preenabled)
1521 panic("x2apic: enabled by BIOS but kernel init failed.");
1522 else if (cpu_has_x2apic)
1523 pr_info("Not enabling x2apic, Intr-remapping init failed.\n");
1524}
1525
1526#ifdef CONFIG_X86_64
1527/*
1528 * Detect and enable local APICs on non-SMP boards.
1529 * Original code written by Keir Fraser.
1530 * On AMD64 we trust the BIOS - if it says no APIC it is likely
1531 * not correctly set up (usually the APIC timer won't work etc.)
1532 */
1533static int __init detect_init_APIC(void)
1534{
1535 if (!cpu_has_apic) {
1536 pr_info("No local APIC present\n");
1537 return -1;
1538 }
1539
1540 mp_lapic_addr = APIC_DEFAULT_PHYS_BASE;
1541 return 0;
1542}
1543#else
1544
1545static int __init apic_verify(void)
1546{
1547 u32 features, h, l;
1548
1549 /*
1550 * The APIC feature bit should now be enabled
1551 * in `cpuid'
1552 */
1553 features = cpuid_edx(1);
1554 if (!(features & (1 << X86_FEATURE_APIC))) {
1555 pr_warning("Could not enable APIC!\n");
1556 return -1;
1557 }
1558 set_cpu_cap(&boot_cpu_data, X86_FEATURE_APIC);
1559 mp_lapic_addr = APIC_DEFAULT_PHYS_BASE;
1560
1561 /* The BIOS may have set up the APIC at some other address */
1562 rdmsr(MSR_IA32_APICBASE, l, h);
1563 if (l & MSR_IA32_APICBASE_ENABLE)
1564 mp_lapic_addr = l & MSR_IA32_APICBASE_BASE;
1565
1566 pr_info("Found and enabled local APIC!\n");
1567 return 0;
1568}
1569
1570int __init apic_force_enable(unsigned long addr)
1571{
1572 u32 h, l;
1573
1574 if (disable_apic)
1575 return -1;
1576
1577 /*
1578 * Some BIOSes disable the local APIC in the APIC_BASE
1579 * MSR. This can only be done in software for Intel P6 or later
1580 * and AMD K7 (Model > 1) or later.
1581 */
1582 rdmsr(MSR_IA32_APICBASE, l, h);
1583 if (!(l & MSR_IA32_APICBASE_ENABLE)) {
1584 pr_info("Local APIC disabled by BIOS -- reenabling.\n");
1585 l &= ~MSR_IA32_APICBASE_BASE;
1586 l |= MSR_IA32_APICBASE_ENABLE | addr;
1587 wrmsr(MSR_IA32_APICBASE, l, h);
1588 enabled_via_apicbase = 1;
1589 }
1590 return apic_verify();
1591}
1592
1593/*
1594 * Detect and initialize APIC
1595 */
1596static int __init detect_init_APIC(void)
1597{
1598 /* Disabled by kernel option? */
1599 if (disable_apic)
1600 return -1;
1601
1602 switch (boot_cpu_data.x86_vendor) {
1603 case X86_VENDOR_AMD:
1604 if ((boot_cpu_data.x86 == 6 && boot_cpu_data.x86_model > 1) ||
1605 (boot_cpu_data.x86 >= 15))
1606 break;
1607 goto no_apic;
1608 case X86_VENDOR_INTEL:
1609 if (boot_cpu_data.x86 == 6 || boot_cpu_data.x86 == 15 ||
1610 (boot_cpu_data.x86 == 5 && cpu_has_apic))
1611 break;
1612 goto no_apic;
1613 default:
1614 goto no_apic;
1615 }
1616
1617 if (!cpu_has_apic) {
1618 /*
1619 * Over-ride BIOS and try to enable the local APIC only if
1620 * "lapic" specified.
1621 */
1622 if (!force_enable_local_apic) {
1623 pr_info("Local APIC disabled by BIOS -- "
1624 "you can enable it with \"lapic\"\n");
1625 return -1;
1626 }
1627 if (apic_force_enable(APIC_DEFAULT_PHYS_BASE))
1628 return -1;
1629 } else {
1630 if (apic_verify())
1631 return -1;
1632 }
1633
1634 apic_pm_activate();
1635
1636 return 0;
1637
1638no_apic:
1639 pr_info("No local APIC present or hardware disabled\n");
1640 return -1;
1641}
1642#endif
1643
1644/**
1645 * init_apic_mappings - initialize APIC mappings
1646 */
1647void __init init_apic_mappings(void)
1648{
1649 unsigned int new_apicid;
1650
1651 if (x2apic_mode) {
1652 boot_cpu_physical_apicid = read_apic_id();
1653 return;
1654 }
1655
1656 /* If no local APIC can be found return early */
1657 if (!smp_found_config && detect_init_APIC()) {
1658 /* lets NOP'ify apic operations */
1659 pr_info("APIC: disable apic facility\n");
1660 apic_disable();
1661 } else {
1662 apic_phys = mp_lapic_addr;
1663
1664 /*
1665 * acpi lapic path already maps that address in
1666 * acpi_register_lapic_address()
1667 */
1668 if (!acpi_lapic && !smp_found_config)
1669 register_lapic_address(apic_phys);
1670 }
1671
1672 /*
1673 * Fetch the APIC ID of the BSP in case we have a
1674 * default configuration (or the MP table is broken).
1675 */
1676 new_apicid = read_apic_id();
1677 if (boot_cpu_physical_apicid != new_apicid) {
1678 boot_cpu_physical_apicid = new_apicid;
1679 /*
1680 * yeah -- we lie about apic_version
1681 * in case if apic was disabled via boot option
1682 * but it's not a problem for SMP compiled kernel
1683 * since smp_sanity_check is prepared for such a case
1684 * and disable smp mode
1685 */
1686 apic_version[new_apicid] =
1687 GET_APIC_VERSION(apic_read(APIC_LVR));
1688 }
1689}
1690
1691void __init register_lapic_address(unsigned long address)
1692{
1693 mp_lapic_addr = address;
1694
1695 if (!x2apic_mode) {
1696 set_fixmap_nocache(FIX_APIC_BASE, address);
1697 apic_printk(APIC_VERBOSE, "mapped APIC to %16lx (%16lx)\n",
1698 APIC_BASE, mp_lapic_addr);
1699 }
1700 if (boot_cpu_physical_apicid == -1U) {
1701 boot_cpu_physical_apicid = read_apic_id();
1702 apic_version[boot_cpu_physical_apicid] =
1703 GET_APIC_VERSION(apic_read(APIC_LVR));
1704 }
1705}
1706
1707/*
1708 * This initializes the IO-APIC and APIC hardware if this is
1709 * a UP kernel.
1710 */
1711int apic_version[MAX_LOCAL_APIC];
1712
1713int __init APIC_init_uniprocessor(void)
1714{
1715 if (disable_apic) {
1716 pr_info("Apic disabled\n");
1717 return -1;
1718 }
1719#ifdef CONFIG_X86_64
1720 if (!cpu_has_apic) {
1721 disable_apic = 1;
1722 pr_info("Apic disabled by BIOS\n");
1723 return -1;
1724 }
1725#else
1726 if (!smp_found_config && !cpu_has_apic)
1727 return -1;
1728
1729 /*
1730 * Complain if the BIOS pretends there is one.
1731 */
1732 if (!cpu_has_apic &&
1733 APIC_INTEGRATED(apic_version[boot_cpu_physical_apicid])) {
1734 pr_err("BIOS bug, local APIC 0x%x not detected!...\n",
1735 boot_cpu_physical_apicid);
1736 return -1;
1737 }
1738#endif
1739
1740 default_setup_apic_routing();
1741
1742 verify_local_APIC();
1743 connect_bsp_APIC();
1744
1745#ifdef CONFIG_X86_64
1746 apic_write(APIC_ID, SET_APIC_ID(boot_cpu_physical_apicid));
1747#else
1748 /*
1749 * Hack: In case of kdump, after a crash, kernel might be booting
1750 * on a cpu with non-zero lapic id. But boot_cpu_physical_apicid
1751 * might be zero if read from MP tables. Get it from LAPIC.
1752 */
1753# ifdef CONFIG_CRASH_DUMP
1754 boot_cpu_physical_apicid = read_apic_id();
1755# endif
1756#endif
1757 physid_set_mask_of_physid(boot_cpu_physical_apicid, &phys_cpu_present_map);
1758 setup_local_APIC();
1759
1760#ifdef CONFIG_X86_IO_APIC
1761 /*
1762 * Now enable IO-APICs, actually call clear_IO_APIC
1763 * We need clear_IO_APIC before enabling error vector
1764 */
1765 if (!skip_ioapic_setup && nr_ioapics)
1766 enable_IO_APIC();
1767#endif
1768
1769 bsp_end_local_APIC_setup();
1770
1771#ifdef CONFIG_X86_IO_APIC
1772 if (smp_found_config && !skip_ioapic_setup && nr_ioapics)
1773 setup_IO_APIC();
1774 else {
1775 nr_ioapics = 0;
1776 }
1777#endif
1778
1779 x86_init.timers.setup_percpu_clockev();
1780 return 0;
1781}
1782
1783/*
1784 * Local APIC interrupts
1785 */
1786
1787/*
1788 * This interrupt should _never_ happen with our APIC/SMP architecture
1789 */
1790void smp_spurious_interrupt(struct pt_regs *regs)
1791{
1792 u32 v;
1793
1794 exit_idle();
1795 irq_enter();
1796 /*
1797 * Check if this really is a spurious interrupt and ACK it
1798 * if it is a vectored one. Just in case...
1799 * Spurious interrupts should not be ACKed.
1800 */
1801 v = apic_read(APIC_ISR + ((SPURIOUS_APIC_VECTOR & ~0x1f) >> 1));
1802 if (v & (1 << (SPURIOUS_APIC_VECTOR & 0x1f)))
1803 ack_APIC_irq();
1804
1805 inc_irq_stat(irq_spurious_count);
1806
1807 /* see sw-dev-man vol 3, chapter 7.4.13.5 */
1808 pr_info("spurious APIC interrupt on CPU#%d, "
1809 "should never happen.\n", smp_processor_id());
1810 irq_exit();
1811}
1812
1813/*
1814 * This interrupt should never happen with our APIC/SMP architecture
1815 */
1816void smp_error_interrupt(struct pt_regs *regs)
1817{
1818 u32 v0, v1;
1819 u32 i = 0;
1820 static const char * const error_interrupt_reason[] = {
1821 "Send CS error", /* APIC Error Bit 0 */
1822 "Receive CS error", /* APIC Error Bit 1 */
1823 "Send accept error", /* APIC Error Bit 2 */
1824 "Receive accept error", /* APIC Error Bit 3 */
1825 "Redirectable IPI", /* APIC Error Bit 4 */
1826 "Send illegal vector", /* APIC Error Bit 5 */
1827 "Received illegal vector", /* APIC Error Bit 6 */
1828 "Illegal register address", /* APIC Error Bit 7 */
1829 };
1830
1831 exit_idle();
1832 irq_enter();
1833 /* First tickle the hardware, only then report what went on. -- REW */
1834 v0 = apic_read(APIC_ESR);
1835 apic_write(APIC_ESR, 0);
1836 v1 = apic_read(APIC_ESR);
1837 ack_APIC_irq();
1838 atomic_inc(&irq_err_count);
1839
1840 apic_printk(APIC_DEBUG, KERN_DEBUG "APIC error on CPU%d: %02x(%02x)",
1841 smp_processor_id(), v0 , v1);
1842
1843 v1 = v1 & 0xff;
1844 while (v1) {
1845 if (v1 & 0x1)
1846 apic_printk(APIC_DEBUG, KERN_CONT " : %s", error_interrupt_reason[i]);
1847 i++;
1848 v1 >>= 1;
1849 };
1850
1851 apic_printk(APIC_DEBUG, KERN_CONT "\n");
1852
1853 irq_exit();
1854}
1855
1856/**
1857 * connect_bsp_APIC - attach the APIC to the interrupt system
1858 */
1859void __init connect_bsp_APIC(void)
1860{
1861#ifdef CONFIG_X86_32
1862 if (pic_mode) {
1863 /*
1864 * Do not trust the local APIC being empty at bootup.
1865 */
1866 clear_local_APIC();
1867 /*
1868 * PIC mode, enable APIC mode in the IMCR, i.e. connect BSP's
1869 * local APIC to INT and NMI lines.
1870 */
1871 apic_printk(APIC_VERBOSE, "leaving PIC mode, "
1872 "enabling APIC mode.\n");
1873 imcr_pic_to_apic();
1874 }
1875#endif
1876 if (apic->enable_apic_mode)
1877 apic->enable_apic_mode();
1878}
1879
1880/**
1881 * disconnect_bsp_APIC - detach the APIC from the interrupt system
1882 * @virt_wire_setup: indicates, whether virtual wire mode is selected
1883 *
1884 * Virtual wire mode is necessary to deliver legacy interrupts even when the
1885 * APIC is disabled.
1886 */
1887void disconnect_bsp_APIC(int virt_wire_setup)
1888{
1889 unsigned int value;
1890
1891#ifdef CONFIG_X86_32
1892 if (pic_mode) {
1893 /*
1894 * Put the board back into PIC mode (has an effect only on
1895 * certain older boards). Note that APIC interrupts, including
1896 * IPIs, won't work beyond this point! The only exception are
1897 * INIT IPIs.
1898 */
1899 apic_printk(APIC_VERBOSE, "disabling APIC mode, "
1900 "entering PIC mode.\n");
1901 imcr_apic_to_pic();
1902 return;
1903 }
1904#endif
1905
1906 /* Go back to Virtual Wire compatibility mode */
1907
1908 /* For the spurious interrupt use vector F, and enable it */
1909 value = apic_read(APIC_SPIV);
1910 value &= ~APIC_VECTOR_MASK;
1911 value |= APIC_SPIV_APIC_ENABLED;
1912 value |= 0xf;
1913 apic_write(APIC_SPIV, value);
1914
1915 if (!virt_wire_setup) {
1916 /*
1917 * For LVT0 make it edge triggered, active high,
1918 * external and enabled
1919 */
1920 value = apic_read(APIC_LVT0);
1921 value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING |
1922 APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
1923 APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED);
1924 value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
1925 value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_EXTINT);
1926 apic_write(APIC_LVT0, value);
1927 } else {
1928 /* Disable LVT0 */
1929 apic_write(APIC_LVT0, APIC_LVT_MASKED);
1930 }
1931
1932 /*
1933 * For LVT1 make it edge triggered, active high,
1934 * nmi and enabled
1935 */
1936 value = apic_read(APIC_LVT1);
1937 value &= ~(APIC_MODE_MASK | APIC_SEND_PENDING |
1938 APIC_INPUT_POLARITY | APIC_LVT_REMOTE_IRR |
1939 APIC_LVT_LEVEL_TRIGGER | APIC_LVT_MASKED);
1940 value |= APIC_LVT_REMOTE_IRR | APIC_SEND_PENDING;
1941 value = SET_APIC_DELIVERY_MODE(value, APIC_MODE_NMI);
1942 apic_write(APIC_LVT1, value);
1943}
1944
1945void __cpuinit generic_processor_info(int apicid, int version)
1946{
1947 int cpu, max = nr_cpu_ids;
1948 bool boot_cpu_detected = physid_isset(boot_cpu_physical_apicid,
1949 phys_cpu_present_map);
1950
1951 /*
1952 * If boot cpu has not been detected yet, then only allow upto
1953 * nr_cpu_ids - 1 processors and keep one slot free for boot cpu
1954 */
1955 if (!boot_cpu_detected && num_processors >= nr_cpu_ids - 1 &&
1956 apicid != boot_cpu_physical_apicid) {
1957 int thiscpu = max + disabled_cpus - 1;
1958
1959 pr_warning(
1960 "ACPI: NR_CPUS/possible_cpus limit of %i almost"
1961 " reached. Keeping one slot for boot cpu."
1962 " Processor %d/0x%x ignored.\n", max, thiscpu, apicid);
1963
1964 disabled_cpus++;
1965 return;
1966 }
1967
1968 if (num_processors >= nr_cpu_ids) {
1969 int thiscpu = max + disabled_cpus;
1970
1971 pr_warning(
1972 "ACPI: NR_CPUS/possible_cpus limit of %i reached."
1973 " Processor %d/0x%x ignored.\n", max, thiscpu, apicid);
1974
1975 disabled_cpus++;
1976 return;
1977 }
1978
1979 num_processors++;
1980 if (apicid == boot_cpu_physical_apicid) {
1981 /*
1982 * x86_bios_cpu_apicid is required to have processors listed
1983 * in same order as logical cpu numbers. Hence the first
1984 * entry is BSP, and so on.
1985 * boot_cpu_init() already hold bit 0 in cpu_present_mask
1986 * for BSP.
1987 */
1988 cpu = 0;
1989 } else
1990 cpu = cpumask_next_zero(-1, cpu_present_mask);
1991
1992 /*
1993 * Validate version
1994 */
1995 if (version == 0x0) {
1996 pr_warning("BIOS bug: APIC version is 0 for CPU %d/0x%x, fixing up to 0x10\n",
1997 cpu, apicid);
1998 version = 0x10;
1999 }
2000 apic_version[apicid] = version;
2001
2002 if (version != apic_version[boot_cpu_physical_apicid]) {
2003 pr_warning("BIOS bug: APIC version mismatch, boot CPU: %x, CPU %d: version %x\n",
2004 apic_version[boot_cpu_physical_apicid], cpu, version);
2005 }
2006
2007 physid_set(apicid, phys_cpu_present_map);
2008 if (apicid > max_physical_apicid)
2009 max_physical_apicid = apicid;
2010
2011#if defined(CONFIG_SMP) || defined(CONFIG_X86_64)
2012 early_per_cpu(x86_cpu_to_apicid, cpu) = apicid;
2013 early_per_cpu(x86_bios_cpu_apicid, cpu) = apicid;
2014#endif
2015#ifdef CONFIG_X86_32
2016 early_per_cpu(x86_cpu_to_logical_apicid, cpu) =
2017 apic->x86_32_early_logical_apicid(cpu);
2018#endif
2019 set_cpu_possible(cpu, true);
2020 set_cpu_present(cpu, true);
2021}
2022
2023int hard_smp_processor_id(void)
2024{
2025 return read_apic_id();
2026}
2027
2028void default_init_apic_ldr(void)
2029{
2030 unsigned long val;
2031
2032 apic_write(APIC_DFR, APIC_DFR_VALUE);
2033 val = apic_read(APIC_LDR) & ~APIC_LDR_MASK;
2034 val |= SET_APIC_LOGICAL_ID(1UL << smp_processor_id());
2035 apic_write(APIC_LDR, val);
2036}
2037
2038/*
2039 * Power management
2040 */
2041#ifdef CONFIG_PM
2042
2043static struct {
2044 /*
2045 * 'active' is true if the local APIC was enabled by us and
2046 * not the BIOS; this signifies that we are also responsible
2047 * for disabling it before entering apm/acpi suspend
2048 */
2049 int active;
2050 /* r/w apic fields */
2051 unsigned int apic_id;
2052 unsigned int apic_taskpri;
2053 unsigned int apic_ldr;
2054 unsigned int apic_dfr;
2055 unsigned int apic_spiv;
2056 unsigned int apic_lvtt;
2057 unsigned int apic_lvtpc;
2058 unsigned int apic_lvt0;
2059 unsigned int apic_lvt1;
2060 unsigned int apic_lvterr;
2061 unsigned int apic_tmict;
2062 unsigned int apic_tdcr;
2063 unsigned int apic_thmr;
2064} apic_pm_state;
2065
2066static int lapic_suspend(void)
2067{
2068 unsigned long flags;
2069 int maxlvt;
2070
2071 if (!apic_pm_state.active)
2072 return 0;
2073
2074 maxlvt = lapic_get_maxlvt();
2075
2076 apic_pm_state.apic_id = apic_read(APIC_ID);
2077 apic_pm_state.apic_taskpri = apic_read(APIC_TASKPRI);
2078 apic_pm_state.apic_ldr = apic_read(APIC_LDR);
2079 apic_pm_state.apic_dfr = apic_read(APIC_DFR);
2080 apic_pm_state.apic_spiv = apic_read(APIC_SPIV);
2081 apic_pm_state.apic_lvtt = apic_read(APIC_LVTT);
2082 if (maxlvt >= 4)
2083 apic_pm_state.apic_lvtpc = apic_read(APIC_LVTPC);
2084 apic_pm_state.apic_lvt0 = apic_read(APIC_LVT0);
2085 apic_pm_state.apic_lvt1 = apic_read(APIC_LVT1);
2086 apic_pm_state.apic_lvterr = apic_read(APIC_LVTERR);
2087 apic_pm_state.apic_tmict = apic_read(APIC_TMICT);
2088 apic_pm_state.apic_tdcr = apic_read(APIC_TDCR);
2089#ifdef CONFIG_X86_THERMAL_VECTOR
2090 if (maxlvt >= 5)
2091 apic_pm_state.apic_thmr = apic_read(APIC_LVTTHMR);
2092#endif
2093
2094 local_irq_save(flags);
2095 disable_local_APIC();
2096
2097 if (intr_remapping_enabled)
2098 disable_intr_remapping();
2099
2100 local_irq_restore(flags);
2101 return 0;
2102}
2103
2104static void lapic_resume(void)
2105{
2106 unsigned int l, h;
2107 unsigned long flags;
2108 int maxlvt;
2109
2110 if (!apic_pm_state.active)
2111 return;
2112
2113 local_irq_save(flags);
2114 if (intr_remapping_enabled) {
2115 /*
2116 * IO-APIC and PIC have their own resume routines.
2117 * We just mask them here to make sure the interrupt
2118 * subsystem is completely quiet while we enable x2apic
2119 * and interrupt-remapping.
2120 */
2121 mask_ioapic_entries();
2122 legacy_pic->mask_all();
2123 }
2124
2125 if (x2apic_mode)
2126 enable_x2apic();
2127 else {
2128 /*
2129 * Make sure the APICBASE points to the right address
2130 *
2131 * FIXME! This will be wrong if we ever support suspend on
2132 * SMP! We'll need to do this as part of the CPU restore!
2133 */
2134 rdmsr(MSR_IA32_APICBASE, l, h);
2135 l &= ~MSR_IA32_APICBASE_BASE;
2136 l |= MSR_IA32_APICBASE_ENABLE | mp_lapic_addr;
2137 wrmsr(MSR_IA32_APICBASE, l, h);
2138 }
2139
2140 maxlvt = lapic_get_maxlvt();
2141 apic_write(APIC_LVTERR, ERROR_APIC_VECTOR | APIC_LVT_MASKED);
2142 apic_write(APIC_ID, apic_pm_state.apic_id);
2143 apic_write(APIC_DFR, apic_pm_state.apic_dfr);
2144 apic_write(APIC_LDR, apic_pm_state.apic_ldr);
2145 apic_write(APIC_TASKPRI, apic_pm_state.apic_taskpri);
2146 apic_write(APIC_SPIV, apic_pm_state.apic_spiv);
2147 apic_write(APIC_LVT0, apic_pm_state.apic_lvt0);
2148 apic_write(APIC_LVT1, apic_pm_state.apic_lvt1);
2149#if defined(CONFIG_X86_MCE_P4THERMAL) || defined(CONFIG_X86_MCE_INTEL)
2150 if (maxlvt >= 5)
2151 apic_write(APIC_LVTTHMR, apic_pm_state.apic_thmr);
2152#endif
2153 if (maxlvt >= 4)
2154 apic_write(APIC_LVTPC, apic_pm_state.apic_lvtpc);
2155 apic_write(APIC_LVTT, apic_pm_state.apic_lvtt);
2156 apic_write(APIC_TDCR, apic_pm_state.apic_tdcr);
2157 apic_write(APIC_TMICT, apic_pm_state.apic_tmict);
2158 apic_write(APIC_ESR, 0);
2159 apic_read(APIC_ESR);
2160 apic_write(APIC_LVTERR, apic_pm_state.apic_lvterr);
2161 apic_write(APIC_ESR, 0);
2162 apic_read(APIC_ESR);
2163
2164 if (intr_remapping_enabled)
2165 reenable_intr_remapping(x2apic_mode);
2166
2167 local_irq_restore(flags);
2168}
2169
2170/*
2171 * This device has no shutdown method - fully functioning local APICs
2172 * are needed on every CPU up until machine_halt/restart/poweroff.
2173 */
2174
2175static struct syscore_ops lapic_syscore_ops = {
2176 .resume = lapic_resume,
2177 .suspend = lapic_suspend,
2178};
2179
2180static void __cpuinit apic_pm_activate(void)
2181{
2182 apic_pm_state.active = 1;
2183}
2184
2185static int __init init_lapic_sysfs(void)
2186{
2187 /* XXX: remove suspend/resume procs if !apic_pm_state.active? */
2188 if (cpu_has_apic)
2189 register_syscore_ops(&lapic_syscore_ops);
2190
2191 return 0;
2192}
2193
2194/* local apic needs to resume before other devices access its registers. */
2195core_initcall(init_lapic_sysfs);
2196
2197#else /* CONFIG_PM */
2198
2199static void apic_pm_activate(void) { }
2200
2201#endif /* CONFIG_PM */
2202
2203#ifdef CONFIG_X86_64
2204
2205static int __cpuinit apic_cluster_num(void)
2206{
2207 int i, clusters, zeros;
2208 unsigned id;
2209 u16 *bios_cpu_apicid;
2210 DECLARE_BITMAP(clustermap, NUM_APIC_CLUSTERS);
2211
2212 bios_cpu_apicid = early_per_cpu_ptr(x86_bios_cpu_apicid);
2213 bitmap_zero(clustermap, NUM_APIC_CLUSTERS);
2214
2215 for (i = 0; i < nr_cpu_ids; i++) {
2216 /* are we being called early in kernel startup? */
2217 if (bios_cpu_apicid) {
2218 id = bios_cpu_apicid[i];
2219 } else if (i < nr_cpu_ids) {
2220 if (cpu_present(i))
2221 id = per_cpu(x86_bios_cpu_apicid, i);
2222 else
2223 continue;
2224 } else
2225 break;
2226
2227 if (id != BAD_APICID)
2228 __set_bit(APIC_CLUSTERID(id), clustermap);
2229 }
2230
2231 /* Problem: Partially populated chassis may not have CPUs in some of
2232 * the APIC clusters they have been allocated. Only present CPUs have
2233 * x86_bios_cpu_apicid entries, thus causing zeroes in the bitmap.
2234 * Since clusters are allocated sequentially, count zeros only if
2235 * they are bounded by ones.
2236 */
2237 clusters = 0;
2238 zeros = 0;
2239 for (i = 0; i < NUM_APIC_CLUSTERS; i++) {
2240 if (test_bit(i, clustermap)) {
2241 clusters += 1 + zeros;
2242 zeros = 0;
2243 } else
2244 ++zeros;
2245 }
2246
2247 return clusters;
2248}
2249
2250static int __cpuinitdata multi_checked;
2251static int __cpuinitdata multi;
2252
2253static int __cpuinit set_multi(const struct dmi_system_id *d)
2254{
2255 if (multi)
2256 return 0;
2257 pr_info("APIC: %s detected, Multi Chassis\n", d->ident);
2258 multi = 1;
2259 return 0;
2260}
2261
2262static const __cpuinitconst struct dmi_system_id multi_dmi_table[] = {
2263 {
2264 .callback = set_multi,
2265 .ident = "IBM System Summit2",
2266 .matches = {
2267 DMI_MATCH(DMI_SYS_VENDOR, "IBM"),
2268 DMI_MATCH(DMI_PRODUCT_NAME, "Summit2"),
2269 },
2270 },
2271 {}
2272};
2273
2274static void __cpuinit dmi_check_multi(void)
2275{
2276 if (multi_checked)
2277 return;
2278
2279 dmi_check_system(multi_dmi_table);
2280 multi_checked = 1;
2281}
2282
2283/*
2284 * apic_is_clustered_box() -- Check if we can expect good TSC
2285 *
2286 * Thus far, the major user of this is IBM's Summit2 series:
2287 * Clustered boxes may have unsynced TSC problems if they are
2288 * multi-chassis.
2289 * Use DMI to check them
2290 */
2291__cpuinit int apic_is_clustered_box(void)
2292{
2293 dmi_check_multi();
2294 if (multi)
2295 return 1;
2296
2297 if (!is_vsmp_box())
2298 return 0;
2299
2300 /*
2301 * ScaleMP vSMPowered boxes have one cluster per board and TSCs are
2302 * not guaranteed to be synced between boards
2303 */
2304 if (apic_cluster_num() > 1)
2305 return 1;
2306
2307 return 0;
2308}
2309#endif
2310
2311/*
2312 * APIC command line parameters
2313 */
2314static int __init setup_disableapic(char *arg)
2315{
2316 disable_apic = 1;
2317 setup_clear_cpu_cap(X86_FEATURE_APIC);
2318 return 0;
2319}
2320early_param("disableapic", setup_disableapic);
2321
2322/* same as disableapic, for compatibility */
2323static int __init setup_nolapic(char *arg)
2324{
2325 return setup_disableapic(arg);
2326}
2327early_param("nolapic", setup_nolapic);
2328
2329static int __init parse_lapic_timer_c2_ok(char *arg)
2330{
2331 local_apic_timer_c2_ok = 1;
2332 return 0;
2333}
2334early_param("lapic_timer_c2_ok", parse_lapic_timer_c2_ok);
2335
2336static int __init parse_disable_apic_timer(char *arg)
2337{
2338 disable_apic_timer = 1;
2339 return 0;
2340}
2341early_param("noapictimer", parse_disable_apic_timer);
2342
2343static int __init parse_nolapic_timer(char *arg)
2344{
2345 disable_apic_timer = 1;
2346 return 0;
2347}
2348early_param("nolapic_timer", parse_nolapic_timer);
2349
2350static int __init apic_set_verbosity(char *arg)
2351{
2352 if (!arg) {
2353#ifdef CONFIG_X86_64
2354 skip_ioapic_setup = 0;
2355 return 0;
2356#endif
2357 return -EINVAL;
2358 }
2359
2360 if (strcmp("debug", arg) == 0)
2361 apic_verbosity = APIC_DEBUG;
2362 else if (strcmp("verbose", arg) == 0)
2363 apic_verbosity = APIC_VERBOSE;
2364 else {
2365 pr_warning("APIC Verbosity level %s not recognised"
2366 " use apic=verbose or apic=debug\n", arg);
2367 return -EINVAL;
2368 }
2369
2370 return 0;
2371}
2372early_param("apic", apic_set_verbosity);
2373
2374static int __init lapic_insert_resource(void)
2375{
2376 if (!apic_phys)
2377 return -1;
2378
2379 /* Put local APIC into the resource map. */
2380 lapic_resource.start = apic_phys;
2381 lapic_resource.end = lapic_resource.start + PAGE_SIZE - 1;
2382 insert_resource(&iomem_resource, &lapic_resource);
2383
2384 return 0;
2385}
2386
2387/*
2388 * need call insert after e820_reserve_resources()
2389 * that is using request_resource
2390 */
2391late_initcall(lapic_insert_resource);