Loading...
1/* SPDX-License-Identifier: GPL-2.0-only */
2/*
3 * mac80211 <-> driver interface
4 *
5 * Copyright 2002-2005, Devicescape Software, Inc.
6 * Copyright 2006-2007 Jiri Benc <jbenc@suse.cz>
7 * Copyright 2007-2010 Johannes Berg <johannes@sipsolutions.net>
8 * Copyright 2013-2014 Intel Mobile Communications GmbH
9 * Copyright (C) 2015 - 2017 Intel Deutschland GmbH
10 * Copyright (C) 2018 - 2024 Intel Corporation
11 */
12
13#ifndef MAC80211_H
14#define MAC80211_H
15
16#include <linux/bug.h>
17#include <linux/kernel.h>
18#include <linux/if_ether.h>
19#include <linux/skbuff.h>
20#include <linux/ieee80211.h>
21#include <linux/lockdep.h>
22#include <net/cfg80211.h>
23#include <net/codel.h>
24#include <net/ieee80211_radiotap.h>
25#include <linux/unaligned.h>
26
27/**
28 * DOC: Introduction
29 *
30 * mac80211 is the Linux stack for 802.11 hardware that implements
31 * only partial functionality in hard- or firmware. This document
32 * defines the interface between mac80211 and low-level hardware
33 * drivers.
34 */
35
36/**
37 * DOC: Calling mac80211 from interrupts
38 *
39 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
40 * called in hardware interrupt context. The low-level driver must not call any
41 * other functions in hardware interrupt context. If there is a need for such
42 * call, the low-level driver should first ACK the interrupt and perform the
43 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
44 * tasklet function.
45 *
46 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
47 * use the non-IRQ-safe functions!
48 */
49
50/**
51 * DOC: Warning
52 *
53 * If you're reading this document and not the header file itself, it will
54 * be incomplete because not all documentation has been converted yet.
55 */
56
57/**
58 * DOC: Frame format
59 *
60 * As a general rule, when frames are passed between mac80211 and the driver,
61 * they start with the IEEE 802.11 header and include the same octets that are
62 * sent over the air except for the FCS which should be calculated by the
63 * hardware.
64 *
65 * There are, however, various exceptions to this rule for advanced features:
66 *
67 * The first exception is for hardware encryption and decryption offload
68 * where the IV/ICV may or may not be generated in hardware.
69 *
70 * Secondly, when the hardware handles fragmentation, the frame handed to
71 * the driver from mac80211 is the MSDU, not the MPDU.
72 */
73
74/**
75 * DOC: mac80211 workqueue
76 *
77 * mac80211 provides its own workqueue for drivers and internal mac80211 use.
78 * The workqueue is a single threaded workqueue and can only be accessed by
79 * helpers for sanity checking. Drivers must ensure all work added onto the
80 * mac80211 workqueue should be cancelled on the driver stop() callback.
81 *
82 * mac80211 will flush the workqueue upon interface removal and during
83 * suspend.
84 *
85 * All work performed on the mac80211 workqueue must not acquire the RTNL lock.
86 *
87 */
88
89/**
90 * DOC: mac80211 software tx queueing
91 *
92 * mac80211 uses an intermediate queueing implementation, designed to allow the
93 * driver to keep hardware queues short and to provide some fairness between
94 * different stations/interfaces.
95 *
96 * Drivers must provide the .wake_tx_queue driver operation by either
97 * linking it to ieee80211_handle_wake_tx_queue() or implementing a custom
98 * handler.
99 *
100 * Intermediate queues (struct ieee80211_txq) are kept per-sta per-tid, with
101 * another per-sta for non-data/non-mgmt and bufferable management frames, and
102 * a single per-vif queue for multicast data frames.
103 *
104 * The driver is expected to initialize its private per-queue data for stations
105 * and interfaces in the .add_interface and .sta_add ops.
106 *
107 * The driver can't access the internal TX queues (iTXQs) directly.
108 * Whenever mac80211 adds a new frame to a queue, it calls the .wake_tx_queue
109 * driver op.
110 * Drivers implementing a custom .wake_tx_queue op can get them by calling
111 * ieee80211_tx_dequeue(). Drivers using ieee80211_handle_wake_tx_queue() will
112 * simply get the individual frames pushed via the .tx driver operation.
113 *
114 * Drivers can optionally delegate responsibility for scheduling queues to
115 * mac80211, to take advantage of airtime fairness accounting. In this case, to
116 * obtain the next queue to pull frames from, the driver calls
117 * ieee80211_next_txq(). The driver is then expected to return the txq using
118 * ieee80211_return_txq().
119 *
120 * For AP powersave TIM handling, the driver only needs to indicate if it has
121 * buffered packets in the driver specific data structures by calling
122 * ieee80211_sta_set_buffered(). For frames buffered in the ieee80211_txq
123 * struct, mac80211 sets the appropriate TIM PVB bits and calls
124 * .release_buffered_frames().
125 * In that callback the driver is therefore expected to release its own
126 * buffered frames and afterwards also frames from the ieee80211_txq (obtained
127 * via the usual ieee80211_tx_dequeue).
128 */
129
130/**
131 * DOC: HW timestamping
132 *
133 * Timing Measurement and Fine Timing Measurement require accurate timestamps
134 * of the action frames TX/RX and their respective acks.
135 *
136 * To report hardware timestamps for Timing Measurement or Fine Timing
137 * Measurement frame RX, the low level driver should set the SKB's hwtstamp
138 * field to the frame RX timestamp and report the ack TX timestamp in the
139 * ieee80211_rx_status struct.
140 *
141 * Similarly, to report hardware timestamps for Timing Measurement or Fine
142 * Timing Measurement frame TX, the driver should set the SKB's hwtstamp field
143 * to the frame TX timestamp and report the ack RX timestamp in the
144 * ieee80211_tx_status struct.
145 */
146struct device;
147
148/**
149 * enum ieee80211_max_queues - maximum number of queues
150 *
151 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
152 * @IEEE80211_MAX_QUEUE_MAP: bitmap with maximum queues set
153 */
154enum ieee80211_max_queues {
155 IEEE80211_MAX_QUEUES = 16,
156 IEEE80211_MAX_QUEUE_MAP = BIT(IEEE80211_MAX_QUEUES) - 1,
157};
158
159#define IEEE80211_INVAL_HW_QUEUE 0xff
160
161/**
162 * enum ieee80211_ac_numbers - AC numbers as used in mac80211
163 * @IEEE80211_AC_VO: voice
164 * @IEEE80211_AC_VI: video
165 * @IEEE80211_AC_BE: best effort
166 * @IEEE80211_AC_BK: background
167 */
168enum ieee80211_ac_numbers {
169 IEEE80211_AC_VO = 0,
170 IEEE80211_AC_VI = 1,
171 IEEE80211_AC_BE = 2,
172 IEEE80211_AC_BK = 3,
173};
174
175/**
176 * struct ieee80211_tx_queue_params - transmit queue configuration
177 *
178 * The information provided in this structure is required for QoS
179 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
180 *
181 * @aifs: arbitration interframe space [0..255]
182 * @cw_min: minimum contention window [a value of the form
183 * 2^n-1 in the range 1..32767]
184 * @cw_max: maximum contention window [like @cw_min]
185 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
186 * @acm: is mandatory admission control required for the access category
187 * @uapsd: is U-APSD mode enabled for the queue
188 * @mu_edca: is the MU EDCA configured
189 * @mu_edca_param_rec: MU EDCA Parameter Record for HE
190 */
191struct ieee80211_tx_queue_params {
192 u16 txop;
193 u16 cw_min;
194 u16 cw_max;
195 u8 aifs;
196 bool acm;
197 bool uapsd;
198 bool mu_edca;
199 struct ieee80211_he_mu_edca_param_ac_rec mu_edca_param_rec;
200};
201
202struct ieee80211_low_level_stats {
203 unsigned int dot11ACKFailureCount;
204 unsigned int dot11RTSFailureCount;
205 unsigned int dot11FCSErrorCount;
206 unsigned int dot11RTSSuccessCount;
207};
208
209/**
210 * enum ieee80211_chanctx_change - change flag for channel context
211 * @IEEE80211_CHANCTX_CHANGE_WIDTH: The channel width changed
212 * @IEEE80211_CHANCTX_CHANGE_RX_CHAINS: The number of RX chains changed
213 * @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed
214 * @IEEE80211_CHANCTX_CHANGE_CHANNEL: switched to another operating channel,
215 * this is used only with channel switching with CSA
216 * @IEEE80211_CHANCTX_CHANGE_MIN_DEF: The min chandef changed
217 * @IEEE80211_CHANCTX_CHANGE_AP: The AP channel definition changed, so (wider
218 * bandwidth) OFDMA settings need to be changed
219 * @IEEE80211_CHANCTX_CHANGE_PUNCTURING: The punctured channel(s) bitmap
220 * was changed.
221 */
222enum ieee80211_chanctx_change {
223 IEEE80211_CHANCTX_CHANGE_WIDTH = BIT(0),
224 IEEE80211_CHANCTX_CHANGE_RX_CHAINS = BIT(1),
225 IEEE80211_CHANCTX_CHANGE_RADAR = BIT(2),
226 IEEE80211_CHANCTX_CHANGE_CHANNEL = BIT(3),
227 IEEE80211_CHANCTX_CHANGE_MIN_DEF = BIT(4),
228 IEEE80211_CHANCTX_CHANGE_AP = BIT(5),
229 IEEE80211_CHANCTX_CHANGE_PUNCTURING = BIT(6),
230};
231
232/**
233 * struct ieee80211_chan_req - A channel "request"
234 * @oper: channel definition to use for operation
235 * @ap: the channel definition of the AP, if any
236 * (otherwise the chan member is %NULL)
237 */
238struct ieee80211_chan_req {
239 struct cfg80211_chan_def oper;
240 struct cfg80211_chan_def ap;
241};
242
243/**
244 * struct ieee80211_chanctx_conf - channel context that vifs may be tuned to
245 *
246 * This is the driver-visible part. The ieee80211_chanctx
247 * that contains it is visible in mac80211 only.
248 *
249 * @def: the channel definition
250 * @min_def: the minimum channel definition currently required.
251 * @ap: the channel definition the AP actually is operating as,
252 * for use with (wider bandwidth) OFDMA
253 * @radio_idx: index of the wiphy radio used used for this channel
254 * @rx_chains_static: The number of RX chains that must always be
255 * active on the channel to receive MIMO transmissions
256 * @rx_chains_dynamic: The number of RX chains that must be enabled
257 * after RTS/CTS handshake to receive SMPS MIMO transmissions;
258 * this will always be >= @rx_chains_static.
259 * @radar_enabled: whether radar detection is enabled on this channel.
260 * @drv_priv: data area for driver use, will always be aligned to
261 * sizeof(void *), size is determined in hw information.
262 */
263struct ieee80211_chanctx_conf {
264 struct cfg80211_chan_def def;
265 struct cfg80211_chan_def min_def;
266 struct cfg80211_chan_def ap;
267
268 int radio_idx;
269 u8 rx_chains_static, rx_chains_dynamic;
270
271 bool radar_enabled;
272
273 u8 drv_priv[] __aligned(sizeof(void *));
274};
275
276/**
277 * enum ieee80211_chanctx_switch_mode - channel context switch mode
278 * @CHANCTX_SWMODE_REASSIGN_VIF: Both old and new contexts already
279 * exist (and will continue to exist), but the virtual interface
280 * needs to be switched from one to the other.
281 * @CHANCTX_SWMODE_SWAP_CONTEXTS: The old context exists but will stop
282 * to exist with this call, the new context doesn't exist but
283 * will be active after this call, the virtual interface switches
284 * from the old to the new (note that the driver may of course
285 * implement this as an on-the-fly chandef switch of the existing
286 * hardware context, but the mac80211 pointer for the old context
287 * will cease to exist and only the new one will later be used
288 * for changes/removal.)
289 */
290enum ieee80211_chanctx_switch_mode {
291 CHANCTX_SWMODE_REASSIGN_VIF,
292 CHANCTX_SWMODE_SWAP_CONTEXTS,
293};
294
295/**
296 * struct ieee80211_vif_chanctx_switch - vif chanctx switch information
297 *
298 * This is structure is used to pass information about a vif that
299 * needs to switch from one chanctx to another. The
300 * &ieee80211_chanctx_switch_mode defines how the switch should be
301 * done.
302 *
303 * @vif: the vif that should be switched from old_ctx to new_ctx
304 * @link_conf: the link conf that's switching
305 * @old_ctx: the old context to which the vif was assigned
306 * @new_ctx: the new context to which the vif must be assigned
307 */
308struct ieee80211_vif_chanctx_switch {
309 struct ieee80211_vif *vif;
310 struct ieee80211_bss_conf *link_conf;
311 struct ieee80211_chanctx_conf *old_ctx;
312 struct ieee80211_chanctx_conf *new_ctx;
313};
314
315/**
316 * enum ieee80211_bss_change - BSS change notification flags
317 *
318 * These flags are used with the bss_info_changed(), link_info_changed()
319 * and vif_cfg_changed() callbacks to indicate which parameter(s) changed.
320 *
321 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
322 * also implies a change in the AID.
323 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
324 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
325 * @BSS_CHANGED_ERP_SLOT: slot timing changed
326 * @BSS_CHANGED_HT: 802.11n parameters changed
327 * @BSS_CHANGED_BASIC_RATES: Basic rateset changed
328 * @BSS_CHANGED_BEACON_INT: Beacon interval changed
329 * @BSS_CHANGED_BSSID: BSSID changed, for whatever
330 * reason (IBSS and managed mode)
331 * @BSS_CHANGED_BEACON: Beacon data changed, retrieve
332 * new beacon (beaconing modes)
333 * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
334 * enabled/disabled (beaconing modes)
335 * @BSS_CHANGED_CQM: Connection quality monitor config changed
336 * @BSS_CHANGED_IBSS: IBSS join status changed
337 * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed.
338 * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note
339 * that it is only ever disabled for station mode.
340 * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface.
341 * @BSS_CHANGED_SSID: SSID changed for this BSS (AP and IBSS mode)
342 * @BSS_CHANGED_AP_PROBE_RESP: Probe Response changed for this BSS (AP mode)
343 * @BSS_CHANGED_PS: PS changed for this BSS (STA mode)
344 * @BSS_CHANGED_TXPOWER: TX power setting changed for this interface
345 * @BSS_CHANGED_P2P_PS: P2P powersave settings (CTWindow, opportunistic PS)
346 * changed
347 * @BSS_CHANGED_BEACON_INFO: Data from the AP's beacon became available:
348 * currently dtim_period only is under consideration.
349 * @BSS_CHANGED_BANDWIDTH: The bandwidth used by this interface changed,
350 * note that this is only called when it changes after the channel
351 * context had been assigned.
352 * @BSS_CHANGED_OCB: OCB join status changed
353 * @BSS_CHANGED_MU_GROUPS: VHT MU-MIMO group id or user position changed
354 * @BSS_CHANGED_KEEP_ALIVE: keep alive options (idle period or protected
355 * keep alive) changed.
356 * @BSS_CHANGED_MCAST_RATE: Multicast Rate setting changed for this interface
357 * @BSS_CHANGED_FTM_RESPONDER: fine timing measurement request responder
358 * functionality changed for this BSS (AP mode).
359 * @BSS_CHANGED_TWT: TWT status changed
360 * @BSS_CHANGED_HE_OBSS_PD: OBSS Packet Detection status changed.
361 * @BSS_CHANGED_HE_BSS_COLOR: BSS Color has changed
362 * @BSS_CHANGED_FILS_DISCOVERY: FILS discovery status changed.
363 * @BSS_CHANGED_UNSOL_BCAST_PROBE_RESP: Unsolicited broadcast probe response
364 * status changed.
365 * @BSS_CHANGED_MLD_VALID_LINKS: MLD valid links status changed.
366 * @BSS_CHANGED_MLD_TTLM: negotiated TID to link mapping was changed
367 * @BSS_CHANGED_TPE: transmit power envelope changed
368 */
369enum ieee80211_bss_change {
370 BSS_CHANGED_ASSOC = 1<<0,
371 BSS_CHANGED_ERP_CTS_PROT = 1<<1,
372 BSS_CHANGED_ERP_PREAMBLE = 1<<2,
373 BSS_CHANGED_ERP_SLOT = 1<<3,
374 BSS_CHANGED_HT = 1<<4,
375 BSS_CHANGED_BASIC_RATES = 1<<5,
376 BSS_CHANGED_BEACON_INT = 1<<6,
377 BSS_CHANGED_BSSID = 1<<7,
378 BSS_CHANGED_BEACON = 1<<8,
379 BSS_CHANGED_BEACON_ENABLED = 1<<9,
380 BSS_CHANGED_CQM = 1<<10,
381 BSS_CHANGED_IBSS = 1<<11,
382 BSS_CHANGED_ARP_FILTER = 1<<12,
383 BSS_CHANGED_QOS = 1<<13,
384 BSS_CHANGED_IDLE = 1<<14,
385 BSS_CHANGED_SSID = 1<<15,
386 BSS_CHANGED_AP_PROBE_RESP = 1<<16,
387 BSS_CHANGED_PS = 1<<17,
388 BSS_CHANGED_TXPOWER = 1<<18,
389 BSS_CHANGED_P2P_PS = 1<<19,
390 BSS_CHANGED_BEACON_INFO = 1<<20,
391 BSS_CHANGED_BANDWIDTH = 1<<21,
392 BSS_CHANGED_OCB = 1<<22,
393 BSS_CHANGED_MU_GROUPS = 1<<23,
394 BSS_CHANGED_KEEP_ALIVE = 1<<24,
395 BSS_CHANGED_MCAST_RATE = 1<<25,
396 BSS_CHANGED_FTM_RESPONDER = 1<<26,
397 BSS_CHANGED_TWT = 1<<27,
398 BSS_CHANGED_HE_OBSS_PD = 1<<28,
399 BSS_CHANGED_HE_BSS_COLOR = 1<<29,
400 BSS_CHANGED_FILS_DISCOVERY = 1<<30,
401 BSS_CHANGED_UNSOL_BCAST_PROBE_RESP = BIT_ULL(31),
402 BSS_CHANGED_MLD_VALID_LINKS = BIT_ULL(33),
403 BSS_CHANGED_MLD_TTLM = BIT_ULL(34),
404 BSS_CHANGED_TPE = BIT_ULL(35),
405
406 /* when adding here, make sure to change ieee80211_reconfig */
407};
408
409/*
410 * The maximum number of IPv4 addresses listed for ARP filtering. If the number
411 * of addresses for an interface increase beyond this value, hardware ARP
412 * filtering will be disabled.
413 */
414#define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4
415
416/**
417 * enum ieee80211_event_type - event to be notified to the low level driver
418 * @RSSI_EVENT: AP's rssi crossed the a threshold set by the driver.
419 * @MLME_EVENT: event related to MLME
420 * @BAR_RX_EVENT: a BAR was received
421 * @BA_FRAME_TIMEOUT: Frames were released from the reordering buffer because
422 * they timed out. This won't be called for each frame released, but only
423 * once each time the timeout triggers.
424 */
425enum ieee80211_event_type {
426 RSSI_EVENT,
427 MLME_EVENT,
428 BAR_RX_EVENT,
429 BA_FRAME_TIMEOUT,
430};
431
432/**
433 * enum ieee80211_rssi_event_data - relevant when event type is %RSSI_EVENT
434 * @RSSI_EVENT_HIGH: AP's rssi went below the threshold set by the driver.
435 * @RSSI_EVENT_LOW: AP's rssi went above the threshold set by the driver.
436 */
437enum ieee80211_rssi_event_data {
438 RSSI_EVENT_HIGH,
439 RSSI_EVENT_LOW,
440};
441
442/**
443 * struct ieee80211_rssi_event - data attached to an %RSSI_EVENT
444 * @data: See &enum ieee80211_rssi_event_data
445 */
446struct ieee80211_rssi_event {
447 enum ieee80211_rssi_event_data data;
448};
449
450/**
451 * enum ieee80211_mlme_event_data - relevant when event type is %MLME_EVENT
452 * @AUTH_EVENT: the MLME operation is authentication
453 * @ASSOC_EVENT: the MLME operation is association
454 * @DEAUTH_RX_EVENT: deauth received..
455 * @DEAUTH_TX_EVENT: deauth sent.
456 */
457enum ieee80211_mlme_event_data {
458 AUTH_EVENT,
459 ASSOC_EVENT,
460 DEAUTH_RX_EVENT,
461 DEAUTH_TX_EVENT,
462};
463
464/**
465 * enum ieee80211_mlme_event_status - relevant when event type is %MLME_EVENT
466 * @MLME_SUCCESS: the MLME operation completed successfully.
467 * @MLME_DENIED: the MLME operation was denied by the peer.
468 * @MLME_TIMEOUT: the MLME operation timed out.
469 */
470enum ieee80211_mlme_event_status {
471 MLME_SUCCESS,
472 MLME_DENIED,
473 MLME_TIMEOUT,
474};
475
476/**
477 * struct ieee80211_mlme_event - data attached to an %MLME_EVENT
478 * @data: See &enum ieee80211_mlme_event_data
479 * @status: See &enum ieee80211_mlme_event_status
480 * @reason: the reason code if applicable
481 */
482struct ieee80211_mlme_event {
483 enum ieee80211_mlme_event_data data;
484 enum ieee80211_mlme_event_status status;
485 u16 reason;
486};
487
488/**
489 * struct ieee80211_ba_event - data attached for BlockAck related events
490 * @sta: pointer to the &ieee80211_sta to which this event relates
491 * @tid: the tid
492 * @ssn: the starting sequence number (for %BAR_RX_EVENT)
493 */
494struct ieee80211_ba_event {
495 struct ieee80211_sta *sta;
496 u16 tid;
497 u16 ssn;
498};
499
500/**
501 * struct ieee80211_event - event to be sent to the driver
502 * @type: The event itself. See &enum ieee80211_event_type.
503 * @u.rssi: relevant if &type is %RSSI_EVENT
504 * @u.mlme: relevant if &type is %AUTH_EVENT
505 * @u.ba: relevant if &type is %BAR_RX_EVENT or %BA_FRAME_TIMEOUT
506 * @u:union holding the fields above
507 */
508struct ieee80211_event {
509 enum ieee80211_event_type type;
510 union {
511 struct ieee80211_rssi_event rssi;
512 struct ieee80211_mlme_event mlme;
513 struct ieee80211_ba_event ba;
514 } u;
515};
516
517/**
518 * struct ieee80211_mu_group_data - STA's VHT MU-MIMO group data
519 *
520 * This structure describes the group id data of VHT MU-MIMO
521 *
522 * @membership: 64 bits array - a bit is set if station is member of the group
523 * @position: 2 bits per group id indicating the position in the group
524 */
525struct ieee80211_mu_group_data {
526 u8 membership[WLAN_MEMBERSHIP_LEN];
527 u8 position[WLAN_USER_POSITION_LEN];
528};
529
530/**
531 * struct ieee80211_ftm_responder_params - FTM responder parameters
532 *
533 * @lci: LCI subelement content
534 * @civicloc: CIVIC location subelement content
535 * @lci_len: LCI data length
536 * @civicloc_len: Civic data length
537 */
538struct ieee80211_ftm_responder_params {
539 const u8 *lci;
540 const u8 *civicloc;
541 size_t lci_len;
542 size_t civicloc_len;
543};
544
545/**
546 * struct ieee80211_fils_discovery - FILS discovery parameters from
547 * IEEE Std 802.11ai-2016, Annex C.3 MIB detail.
548 *
549 * @min_interval: Minimum packet interval in TUs (0 - 10000)
550 * @max_interval: Maximum packet interval in TUs (0 - 10000)
551 */
552struct ieee80211_fils_discovery {
553 u32 min_interval;
554 u32 max_interval;
555};
556
557#define IEEE80211_TPE_EIRP_ENTRIES_320MHZ 5
558struct ieee80211_parsed_tpe_eirp {
559 bool valid;
560 s8 power[IEEE80211_TPE_EIRP_ENTRIES_320MHZ];
561 u8 count;
562};
563
564#define IEEE80211_TPE_PSD_ENTRIES_320MHZ 16
565struct ieee80211_parsed_tpe_psd {
566 bool valid;
567 s8 power[IEEE80211_TPE_PSD_ENTRIES_320MHZ];
568 u8 count, n;
569};
570
571/**
572 * struct ieee80211_parsed_tpe - parsed transmit power envelope information
573 * @max_local: maximum local EIRP, one value for 20, 40, 80, 160, 320 MHz each
574 * (indexed by TX power category)
575 * @max_reg_client: maximum regulatory client EIRP, one value for 20, 40, 80,
576 * 160, 320 MHz each
577 * (indexed by TX power category)
578 * @psd_local: maximum local power spectral density, one value for each 20 MHz
579 * subchannel per bss_conf's chanreq.oper
580 * (indexed by TX power category)
581 * @psd_reg_client: maximum regulatory power spectral density, one value for
582 * each 20 MHz subchannel per bss_conf's chanreq.oper
583 * (indexed by TX power category)
584 */
585struct ieee80211_parsed_tpe {
586 struct ieee80211_parsed_tpe_eirp max_local[2], max_reg_client[2];
587 struct ieee80211_parsed_tpe_psd psd_local[2], psd_reg_client[2];
588};
589
590/**
591 * struct ieee80211_bss_conf - holds the BSS's changing parameters
592 *
593 * This structure keeps information about a BSS (and an association
594 * to that BSS) that can change during the lifetime of the BSS.
595 *
596 * @vif: reference to owning VIF
597 * @bss: the cfg80211 bss descriptor. Valid only for a station, and only
598 * when associated. Note: This contains information which is not
599 * necessarily authenticated. For example, information coming from probe
600 * responses.
601 * @addr: (link) address used locally
602 * @link_id: link ID, or 0 for non-MLO
603 * @htc_trig_based_pkt_ext: default PE in 4us units, if BSS supports HE
604 * @uora_exists: is the UORA element advertised by AP
605 * @uora_ocw_range: UORA element's OCW Range field
606 * @frame_time_rts_th: HE duration RTS threshold, in units of 32us
607 * @he_support: does this BSS support HE
608 * @twt_requester: does this BSS support TWT requester (relevant for managed
609 * mode only, set if the AP advertises TWT responder role)
610 * @twt_responder: does this BSS support TWT requester (relevant for managed
611 * mode only, set if the AP advertises TWT responder role)
612 * @twt_protected: does this BSS support protected TWT frames
613 * @twt_broadcast: does this BSS support broadcast TWT
614 * @use_cts_prot: use CTS protection
615 * @use_short_preamble: use 802.11b short preamble
616 * @use_short_slot: use short slot time (only relevant for ERP)
617 * @dtim_period: num of beacons before the next DTIM, for beaconing,
618 * valid in station mode only if after the driver was notified
619 * with the %BSS_CHANGED_BEACON_INFO flag, will be non-zero then.
620 * @sync_tsf: last beacon's/probe response's TSF timestamp (could be old
621 * as it may have been received during scanning long ago). If the
622 * HW flag %IEEE80211_HW_TIMING_BEACON_ONLY is set, then this can
623 * only come from a beacon, but might not become valid until after
624 * association when a beacon is received (which is notified with the
625 * %BSS_CHANGED_DTIM flag.). See also sync_dtim_count important notice.
626 * @sync_device_ts: the device timestamp corresponding to the sync_tsf,
627 * the driver/device can use this to calculate synchronisation
628 * (see @sync_tsf). See also sync_dtim_count important notice.
629 * @sync_dtim_count: Only valid when %IEEE80211_HW_TIMING_BEACON_ONLY
630 * is requested, see @sync_tsf/@sync_device_ts.
631 * IMPORTANT: These three sync_* parameters would possibly be out of sync
632 * by the time the driver will use them. The synchronized view is currently
633 * guaranteed only in certain callbacks.
634 * Note also that this is not used with MLD associations, mac80211 doesn't
635 * know how to track beacons for all of the links for this.
636 * @beacon_int: beacon interval
637 * @assoc_capability: capabilities taken from assoc resp
638 * @basic_rates: bitmap of basic rates, each bit stands for an
639 * index into the rate table configured by the driver in
640 * the current band.
641 * @beacon_rate: associated AP's beacon TX rate
642 * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
643 * @bssid: The BSSID for this BSS
644 * @enable_beacon: whether beaconing should be enabled or not
645 * @chanreq: Channel request for this BSS -- the hardware might be
646 * configured a higher bandwidth than this BSS uses, for example.
647 * @mu_group: VHT MU-MIMO group membership data
648 * @ht_operation_mode: HT operation mode like in &struct ieee80211_ht_operation.
649 * This field is only valid when the channel is a wide HT/VHT channel.
650 * Note that with TDLS this can be the case (channel is HT, protection must
651 * be used from this field) even when the BSS association isn't using HT.
652 * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
653 * implies disabled. As with the cfg80211 callback, a change here should
654 * cause an event to be sent indicating where the current value is in
655 * relation to the newly configured threshold.
656 * @cqm_rssi_low: Connection quality monitor RSSI lower threshold, a zero value
657 * implies disabled. This is an alternative mechanism to the single
658 * threshold event and can't be enabled simultaneously with it.
659 * @cqm_rssi_high: Connection quality monitor RSSI upper threshold.
660 * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis
661 * @qos: This is a QoS-enabled BSS.
662 * @hidden_ssid: The SSID of the current vif is hidden. Only valid in AP-mode.
663 * @txpower: TX power in dBm. INT_MIN means not configured.
664 * @txpower_type: TX power adjustment used to control per packet Transmit
665 * Power Control (TPC) in lower driver for the current vif. In particular
666 * TPC is enabled if value passed in %txpower_type is
667 * NL80211_TX_POWER_LIMITED (allow using less than specified from
668 * userspace), whereas TPC is disabled if %txpower_type is set to
669 * NL80211_TX_POWER_FIXED (use value configured from userspace)
670 * @p2p_noa_attr: P2P NoA attribute for P2P powersave
671 * @allow_p2p_go_ps: indication for AP or P2P GO interface, whether it's allowed
672 * to use P2P PS mechanism or not. AP/P2P GO is not allowed to use P2P PS
673 * if it has associated clients without P2P PS support.
674 * @max_idle_period: the time period during which the station can refrain from
675 * transmitting frames to its associated AP without being disassociated.
676 * In units of 1000 TUs. Zero value indicates that the AP did not include
677 * a (valid) BSS Max Idle Period Element.
678 * @protected_keep_alive: if set, indicates that the station should send an RSN
679 * protected frame to the AP to reset the idle timer at the AP for the
680 * station.
681 * @ftm_responder: whether to enable or disable fine timing measurement FTM
682 * responder functionality.
683 * @ftmr_params: configurable lci/civic parameter when enabling FTM responder.
684 * @nontransmitted: this BSS is a nontransmitted BSS profile
685 * @transmitter_bssid: the address of transmitter AP
686 * @bssid_index: index inside the multiple BSSID set
687 * @bssid_indicator: 2^bssid_indicator is the maximum number of APs in set
688 * @ema_ap: AP supports enhancements of discovery and advertisement of
689 * nontransmitted BSSIDs
690 * @profile_periodicity: the least number of beacon frames need to be received
691 * in order to discover all the nontransmitted BSSIDs in the set.
692 * @he_oper: HE operation information of the BSS (AP/Mesh) or of the AP we are
693 * connected to (STA)
694 * @he_obss_pd: OBSS Packet Detection parameters.
695 * @he_bss_color: BSS coloring settings, if BSS supports HE
696 * @fils_discovery: FILS discovery configuration
697 * @unsol_bcast_probe_resp_interval: Unsolicited broadcast probe response
698 * interval.
699 * @beacon_tx_rate: The configured beacon transmit rate that needs to be passed
700 * to driver when rate control is offloaded to firmware.
701 * @power_type: power type of BSS for 6 GHz
702 * @tpe: transmit power envelope information
703 * @pwr_reduction: power constraint of BSS.
704 * @eht_support: does this BSS support EHT
705 * @csa_active: marks whether a channel switch is going on.
706 * @mu_mimo_owner: indicates interface owns MU-MIMO capability
707 * @chanctx_conf: The channel context this interface is assigned to, or %NULL
708 * when it is not assigned. This pointer is RCU-protected due to the TX
709 * path needing to access it; even though the netdev carrier will always
710 * be off when it is %NULL there can still be races and packets could be
711 * processed after it switches back to %NULL.
712 * @color_change_active: marks whether a color change is ongoing.
713 * @color_change_color: the bss color that will be used after the change.
714 * @ht_ldpc: in AP mode, indicates interface has HT LDPC capability.
715 * @vht_ldpc: in AP mode, indicates interface has VHT LDPC capability.
716 * @he_ldpc: in AP mode, indicates interface has HE LDPC capability.
717 * @vht_su_beamformer: in AP mode, does this BSS support operation as an VHT SU
718 * beamformer
719 * @vht_su_beamformee: in AP mode, does this BSS support operation as an VHT SU
720 * beamformee
721 * @vht_mu_beamformer: in AP mode, does this BSS support operation as an VHT MU
722 * beamformer
723 * @vht_mu_beamformee: in AP mode, does this BSS support operation as an VHT MU
724 * beamformee
725 * @he_su_beamformer: in AP-mode, does this BSS support operation as an HE SU
726 * beamformer
727 * @he_su_beamformee: in AP-mode, does this BSS support operation as an HE SU
728 * beamformee
729 * @he_mu_beamformer: in AP-mode, does this BSS support operation as an HE MU
730 * beamformer
731 * @he_full_ul_mumimo: does this BSS support the reception (AP) or transmission
732 * (non-AP STA) of an HE TB PPDU on an RU that spans the entire PPDU
733 * bandwidth
734 * @eht_su_beamformer: in AP-mode, does this BSS enable operation as an EHT SU
735 * beamformer
736 * @eht_su_beamformee: in AP-mode, does this BSS enable operation as an EHT SU
737 * beamformee
738 * @eht_mu_beamformer: in AP-mode, does this BSS enable operation as an EHT MU
739 * beamformer
740 * @eht_80mhz_full_bw_ul_mumimo: in AP-mode, does this BSS support the
741 * reception of an EHT TB PPDU on an RU that spans the entire PPDU
742 * bandwidth
743 * @bss_param_ch_cnt: in BSS-mode, the BSS params change count. This
744 * information is the latest known value. It can come from this link's
745 * beacon or from a beacon sent by another link.
746 * @bss_param_ch_cnt_link_id: in BSS-mode, the link_id to which the beacon
747 * that updated &bss_param_ch_cnt belongs. E.g. if link 1 doesn't hear
748 * its beacons, and link 2 sent a beacon with an RNR element that updated
749 * link 1's BSS params change count, then, link 1's
750 * bss_param_ch_cnt_link_id will be 2. That means that link 1 knows that
751 * link 2 was the link that updated its bss_param_ch_cnt value.
752 * In case link 1 hears its beacon again, bss_param_ch_cnt_link_id will
753 * be updated to 1, even if bss_param_ch_cnt didn't change. This allows
754 * the link to know that it heard the latest value from its own beacon
755 * (as opposed to hearing its value from another link's beacon).
756 */
757struct ieee80211_bss_conf {
758 struct ieee80211_vif *vif;
759 struct cfg80211_bss *bss;
760
761 const u8 *bssid;
762 unsigned int link_id;
763 u8 addr[ETH_ALEN] __aligned(2);
764 u8 htc_trig_based_pkt_ext;
765 bool uora_exists;
766 u8 uora_ocw_range;
767 u16 frame_time_rts_th;
768 bool he_support;
769 bool twt_requester;
770 bool twt_responder;
771 bool twt_protected;
772 bool twt_broadcast;
773 /* erp related data */
774 bool use_cts_prot;
775 bool use_short_preamble;
776 bool use_short_slot;
777 bool enable_beacon;
778 u8 dtim_period;
779 u16 beacon_int;
780 u16 assoc_capability;
781 u64 sync_tsf;
782 u32 sync_device_ts;
783 u8 sync_dtim_count;
784 u32 basic_rates;
785 struct ieee80211_rate *beacon_rate;
786 int mcast_rate[NUM_NL80211_BANDS];
787 u16 ht_operation_mode;
788 s32 cqm_rssi_thold;
789 u32 cqm_rssi_hyst;
790 s32 cqm_rssi_low;
791 s32 cqm_rssi_high;
792 struct ieee80211_chan_req chanreq;
793 struct ieee80211_mu_group_data mu_group;
794 bool qos;
795 bool hidden_ssid;
796 int txpower;
797 enum nl80211_tx_power_setting txpower_type;
798 struct ieee80211_p2p_noa_attr p2p_noa_attr;
799 bool allow_p2p_go_ps;
800 u16 max_idle_period;
801 bool protected_keep_alive;
802 bool ftm_responder;
803 struct ieee80211_ftm_responder_params *ftmr_params;
804 /* Multiple BSSID data */
805 bool nontransmitted;
806 u8 transmitter_bssid[ETH_ALEN];
807 u8 bssid_index;
808 u8 bssid_indicator;
809 bool ema_ap;
810 u8 profile_periodicity;
811 struct {
812 u32 params;
813 u16 nss_set;
814 } he_oper;
815 struct ieee80211_he_obss_pd he_obss_pd;
816 struct cfg80211_he_bss_color he_bss_color;
817 struct ieee80211_fils_discovery fils_discovery;
818 u32 unsol_bcast_probe_resp_interval;
819 struct cfg80211_bitrate_mask beacon_tx_rate;
820 enum ieee80211_ap_reg_power power_type;
821
822 struct ieee80211_parsed_tpe tpe;
823
824 u8 pwr_reduction;
825 bool eht_support;
826
827 bool csa_active;
828
829 bool mu_mimo_owner;
830 struct ieee80211_chanctx_conf __rcu *chanctx_conf;
831
832 bool color_change_active;
833 u8 color_change_color;
834
835 bool ht_ldpc;
836 bool vht_ldpc;
837 bool he_ldpc;
838 bool vht_su_beamformer;
839 bool vht_su_beamformee;
840 bool vht_mu_beamformer;
841 bool vht_mu_beamformee;
842 bool he_su_beamformer;
843 bool he_su_beamformee;
844 bool he_mu_beamformer;
845 bool he_full_ul_mumimo;
846 bool eht_su_beamformer;
847 bool eht_su_beamformee;
848 bool eht_mu_beamformer;
849 bool eht_80mhz_full_bw_ul_mumimo;
850 u8 bss_param_ch_cnt;
851 u8 bss_param_ch_cnt_link_id;
852};
853
854/**
855 * enum mac80211_tx_info_flags - flags to describe transmission information/status
856 *
857 * These flags are used with the @flags member of &ieee80211_tx_info.
858 *
859 * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame.
860 * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
861 * number to this frame, taking care of not overwriting the fragment
862 * number and increasing the sequence number only when the
863 * IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
864 * assign sequence numbers to QoS-data frames but cannot do so correctly
865 * for non-QoS-data and management frames because beacons need them from
866 * that counter as well and mac80211 cannot guarantee proper sequencing.
867 * If this flag is set, the driver should instruct the hardware to
868 * assign a sequence number to the frame or assign one itself. Cf. IEEE
869 * 802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
870 * beacons and always be clear for frames without a sequence number field.
871 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
872 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
873 * station
874 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
875 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
876 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
877 * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
878 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
879 * because the destination STA was in powersave mode. Note that to
880 * avoid race conditions, the filter must be set by the hardware or
881 * firmware upon receiving a frame that indicates that the station
882 * went to sleep (must be done on device to filter frames already on
883 * the queue) and may only be unset after mac80211 gives the OK for
884 * that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above),
885 * since only then is it guaranteed that no more frames are in the
886 * hardware queue.
887 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
888 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
889 * is for the whole aggregation.
890 * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
891 * so consider using block ack request (BAR).
892 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
893 * set by rate control algorithms to indicate probe rate, will
894 * be cleared for fragmented frames (except on the last fragment)
895 * @IEEE80211_TX_INTFL_OFFCHAN_TX_OK: Internal to mac80211. Used to indicate
896 * that a frame can be transmitted while the queues are stopped for
897 * off-channel operation.
898 * @IEEE80211_TX_CTL_HW_80211_ENCAP: This frame uses hardware encapsulation
899 * (header conversion)
900 * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211,
901 * used to indicate that a frame was already retried due to PS
902 * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
903 * used to indicate frame should not be encrypted
904 * @IEEE80211_TX_CTL_NO_PS_BUFFER: This frame is a response to a poll
905 * frame (PS-Poll or uAPSD) or a non-bufferable MMPDU and must
906 * be sent although the station is in powersave mode.
907 * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the
908 * transmit function after the current frame, this can be used
909 * by drivers to kick the DMA queue only if unset or when the
910 * queue gets full.
911 * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted
912 * after TX status because the destination was asleep, it must not
913 * be modified again (no seqno assignment, crypto, etc.)
914 * @IEEE80211_TX_INTFL_MLME_CONN_TX: This frame was transmitted by the MLME
915 * code for connection establishment, this indicates that its status
916 * should kick the MLME state machine.
917 * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211
918 * MLME command (internal to mac80211 to figure out whether to send TX
919 * status to user space)
920 * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame
921 * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this
922 * frame and selects the maximum number of streams that it can use.
923 * @IEEE80211_TX_CTL_TX_OFFCHAN: Marks this packet to be transmitted on
924 * the off-channel channel when a remain-on-channel offload is done
925 * in hardware -- normal packets still flow and are expected to be
926 * handled properly by the device.
927 * @IEEE80211_TX_INTFL_TKIP_MIC_FAILURE: Marks this packet to be used for TKIP
928 * testing. It will be sent out with incorrect Michael MIC key to allow
929 * TKIP countermeasures to be tested.
930 * @IEEE80211_TX_CTL_NO_CCK_RATE: This frame will be sent at non CCK rate.
931 * This flag is actually used for management frame especially for P2P
932 * frames not being sent at CCK rate in 2GHz band.
933 * @IEEE80211_TX_STATUS_EOSP: This packet marks the end of service period,
934 * when its status is reported the service period ends. For frames in
935 * an SP that mac80211 transmits, it is already set; for driver frames
936 * the driver may set this flag. It is also used to do the same for
937 * PS-Poll responses.
938 * @IEEE80211_TX_CTL_USE_MINRATE: This frame will be sent at lowest rate.
939 * This flag is used to send nullfunc frame at minimum rate when
940 * the nullfunc is used for connection monitoring purpose.
941 * @IEEE80211_TX_CTL_DONTFRAG: Don't fragment this packet even if it
942 * would be fragmented by size (this is optional, only used for
943 * monitor injection).
944 * @IEEE80211_TX_STAT_NOACK_TRANSMITTED: A frame that was marked with
945 * IEEE80211_TX_CTL_NO_ACK has been successfully transmitted without
946 * any errors (like issues specific to the driver/HW).
947 * This flag must not be set for frames that don't request no-ack
948 * behaviour with IEEE80211_TX_CTL_NO_ACK.
949 *
950 * Note: If you have to add new flags to the enumeration, then don't
951 * forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary.
952 */
953enum mac80211_tx_info_flags {
954 IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
955 IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(1),
956 IEEE80211_TX_CTL_NO_ACK = BIT(2),
957 IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(3),
958 IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(4),
959 IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(5),
960 IEEE80211_TX_CTL_AMPDU = BIT(6),
961 IEEE80211_TX_CTL_INJECTED = BIT(7),
962 IEEE80211_TX_STAT_TX_FILTERED = BIT(8),
963 IEEE80211_TX_STAT_ACK = BIT(9),
964 IEEE80211_TX_STAT_AMPDU = BIT(10),
965 IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11),
966 IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12),
967 IEEE80211_TX_INTFL_OFFCHAN_TX_OK = BIT(13),
968 IEEE80211_TX_CTL_HW_80211_ENCAP = BIT(14),
969 IEEE80211_TX_INTFL_RETRIED = BIT(15),
970 IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16),
971 IEEE80211_TX_CTL_NO_PS_BUFFER = BIT(17),
972 IEEE80211_TX_CTL_MORE_FRAMES = BIT(18),
973 IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19),
974 IEEE80211_TX_INTFL_MLME_CONN_TX = BIT(20),
975 IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21),
976 IEEE80211_TX_CTL_LDPC = BIT(22),
977 IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24),
978 IEEE80211_TX_CTL_TX_OFFCHAN = BIT(25),
979 IEEE80211_TX_INTFL_TKIP_MIC_FAILURE = BIT(26),
980 IEEE80211_TX_CTL_NO_CCK_RATE = BIT(27),
981 IEEE80211_TX_STATUS_EOSP = BIT(28),
982 IEEE80211_TX_CTL_USE_MINRATE = BIT(29),
983 IEEE80211_TX_CTL_DONTFRAG = BIT(30),
984 IEEE80211_TX_STAT_NOACK_TRANSMITTED = BIT(31),
985};
986
987#define IEEE80211_TX_CTL_STBC_SHIFT 23
988
989#define IEEE80211_TX_RC_S1G_MCS IEEE80211_TX_RC_VHT_MCS
990
991/**
992 * enum mac80211_tx_control_flags - flags to describe transmit control
993 *
994 * @IEEE80211_TX_CTRL_PORT_CTRL_PROTO: this frame is a port control
995 * protocol frame (e.g. EAP)
996 * @IEEE80211_TX_CTRL_PS_RESPONSE: This frame is a response to a poll
997 * frame (PS-Poll or uAPSD).
998 * @IEEE80211_TX_CTRL_RATE_INJECT: This frame is injected with rate information
999 * @IEEE80211_TX_CTRL_AMSDU: This frame is an A-MSDU frame
1000 * @IEEE80211_TX_CTRL_FAST_XMIT: This frame is going through the fast_xmit path
1001 * @IEEE80211_TX_CTRL_SKIP_MPATH_LOOKUP: This frame skips mesh path lookup
1002 * @IEEE80211_TX_INTCFL_NEED_TXPROCESSING: completely internal to mac80211,
1003 * used to indicate that a pending frame requires TX processing before
1004 * it can be sent out.
1005 * @IEEE80211_TX_CTRL_NO_SEQNO: Do not overwrite the sequence number that
1006 * has already been assigned to this frame.
1007 * @IEEE80211_TX_CTRL_DONT_REORDER: This frame should not be reordered
1008 * relative to other frames that have this flag set, independent
1009 * of their QoS TID or other priority field values.
1010 * @IEEE80211_TX_CTRL_MCAST_MLO_FIRST_TX: first MLO TX, used mostly internally
1011 * for sequence number assignment
1012 * @IEEE80211_TX_CTRL_DONT_USE_RATE_MASK: Don't use rate mask for this frame
1013 * which is transmitted due to scanning or offchannel TX, not in normal
1014 * operation on the interface.
1015 * @IEEE80211_TX_CTRL_MLO_LINK: If not @IEEE80211_LINK_UNSPECIFIED, this
1016 * frame should be transmitted on the specific link. This really is
1017 * only relevant for frames that do not have data present, and is
1018 * also not used for 802.3 format frames. Note that even if the frame
1019 * is on a specific link, address translation might still apply if
1020 * it's intended for an MLD.
1021 *
1022 * These flags are used in tx_info->control.flags.
1023 */
1024enum mac80211_tx_control_flags {
1025 IEEE80211_TX_CTRL_PORT_CTRL_PROTO = BIT(0),
1026 IEEE80211_TX_CTRL_PS_RESPONSE = BIT(1),
1027 IEEE80211_TX_CTRL_RATE_INJECT = BIT(2),
1028 IEEE80211_TX_CTRL_AMSDU = BIT(3),
1029 IEEE80211_TX_CTRL_FAST_XMIT = BIT(4),
1030 IEEE80211_TX_CTRL_SKIP_MPATH_LOOKUP = BIT(5),
1031 IEEE80211_TX_INTCFL_NEED_TXPROCESSING = BIT(6),
1032 IEEE80211_TX_CTRL_NO_SEQNO = BIT(7),
1033 IEEE80211_TX_CTRL_DONT_REORDER = BIT(8),
1034 IEEE80211_TX_CTRL_MCAST_MLO_FIRST_TX = BIT(9),
1035 IEEE80211_TX_CTRL_DONT_USE_RATE_MASK = BIT(10),
1036 IEEE80211_TX_CTRL_MLO_LINK = 0xf0000000,
1037};
1038
1039#define IEEE80211_LINK_UNSPECIFIED 0xf
1040#define IEEE80211_TX_CTRL_MLO_LINK_UNSPEC \
1041 u32_encode_bits(IEEE80211_LINK_UNSPECIFIED, \
1042 IEEE80211_TX_CTRL_MLO_LINK)
1043
1044/**
1045 * enum mac80211_tx_status_flags - flags to describe transmit status
1046 *
1047 * @IEEE80211_TX_STATUS_ACK_SIGNAL_VALID: ACK signal is valid
1048 *
1049 * These flags are used in tx_info->status.flags.
1050 */
1051enum mac80211_tx_status_flags {
1052 IEEE80211_TX_STATUS_ACK_SIGNAL_VALID = BIT(0),
1053};
1054
1055/*
1056 * This definition is used as a mask to clear all temporary flags, which are
1057 * set by the tx handlers for each transmission attempt by the mac80211 stack.
1058 */
1059#define IEEE80211_TX_TEMPORARY_FLAGS (IEEE80211_TX_CTL_NO_ACK | \
1060 IEEE80211_TX_CTL_CLEAR_PS_FILT | IEEE80211_TX_CTL_FIRST_FRAGMENT | \
1061 IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU | \
1062 IEEE80211_TX_STAT_TX_FILTERED | IEEE80211_TX_STAT_ACK | \
1063 IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK | \
1064 IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_NO_PS_BUFFER | \
1065 IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC | \
1066 IEEE80211_TX_CTL_STBC | IEEE80211_TX_STATUS_EOSP)
1067
1068/**
1069 * enum mac80211_rate_control_flags - per-rate flags set by the
1070 * Rate Control algorithm.
1071 *
1072 * These flags are set by the Rate control algorithm for each rate during tx,
1073 * in the @flags member of struct ieee80211_tx_rate.
1074 *
1075 * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
1076 * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
1077 * This is set if the current BSS requires ERP protection.
1078 * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
1079 * @IEEE80211_TX_RC_MCS: HT rate.
1080 * @IEEE80211_TX_RC_VHT_MCS: VHT MCS rate, in this case the idx field is split
1081 * into a higher 4 bits (Nss) and lower 4 bits (MCS number)
1082 * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
1083 * Greenfield mode.
1084 * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
1085 * @IEEE80211_TX_RC_80_MHZ_WIDTH: Indicates 80 MHz transmission
1086 * @IEEE80211_TX_RC_160_MHZ_WIDTH: Indicates 160 MHz transmission
1087 * (80+80 isn't supported yet)
1088 * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
1089 * adjacent 20 MHz channels, if the current channel type is
1090 * NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
1091 * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
1092 */
1093enum mac80211_rate_control_flags {
1094 IEEE80211_TX_RC_USE_RTS_CTS = BIT(0),
1095 IEEE80211_TX_RC_USE_CTS_PROTECT = BIT(1),
1096 IEEE80211_TX_RC_USE_SHORT_PREAMBLE = BIT(2),
1097
1098 /* rate index is an HT/VHT MCS instead of an index */
1099 IEEE80211_TX_RC_MCS = BIT(3),
1100 IEEE80211_TX_RC_GREEN_FIELD = BIT(4),
1101 IEEE80211_TX_RC_40_MHZ_WIDTH = BIT(5),
1102 IEEE80211_TX_RC_DUP_DATA = BIT(6),
1103 IEEE80211_TX_RC_SHORT_GI = BIT(7),
1104 IEEE80211_TX_RC_VHT_MCS = BIT(8),
1105 IEEE80211_TX_RC_80_MHZ_WIDTH = BIT(9),
1106 IEEE80211_TX_RC_160_MHZ_WIDTH = BIT(10),
1107};
1108
1109
1110/* there are 40 bytes if you don't need the rateset to be kept */
1111#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
1112
1113/* if you do need the rateset, then you have less space */
1114#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
1115
1116/* maximum number of rate stages */
1117#define IEEE80211_TX_MAX_RATES 4
1118
1119/* maximum number of rate table entries */
1120#define IEEE80211_TX_RATE_TABLE_SIZE 4
1121
1122/**
1123 * struct ieee80211_tx_rate - rate selection/status
1124 *
1125 * @idx: rate index to attempt to send with
1126 * @flags: rate control flags (&enum mac80211_rate_control_flags)
1127 * @count: number of tries in this rate before going to the next rate
1128 *
1129 * A value of -1 for @idx indicates an invalid rate and, if used
1130 * in an array of retry rates, that no more rates should be tried.
1131 *
1132 * When used for transmit status reporting, the driver should
1133 * always report the rate along with the flags it used.
1134 *
1135 * &struct ieee80211_tx_info contains an array of these structs
1136 * in the control information, and it will be filled by the rate
1137 * control algorithm according to what should be sent. For example,
1138 * if this array contains, in the format { <idx>, <count> } the
1139 * information::
1140 *
1141 * { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 }
1142 *
1143 * then this means that the frame should be transmitted
1144 * up to twice at rate 3, up to twice at rate 2, and up to four
1145 * times at rate 1 if it doesn't get acknowledged. Say it gets
1146 * acknowledged by the peer after the fifth attempt, the status
1147 * information should then contain::
1148 *
1149 * { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ...
1150 *
1151 * since it was transmitted twice at rate 3, twice at rate 2
1152 * and once at rate 1 after which we received an acknowledgement.
1153 */
1154struct ieee80211_tx_rate {
1155 s8 idx;
1156 u16 count:5,
1157 flags:11;
1158} __packed;
1159
1160#define IEEE80211_MAX_TX_RETRY 31
1161
1162static inline bool ieee80211_rate_valid(struct ieee80211_tx_rate *rate)
1163{
1164 return rate->idx >= 0 && rate->count > 0;
1165}
1166
1167static inline void ieee80211_rate_set_vht(struct ieee80211_tx_rate *rate,
1168 u8 mcs, u8 nss)
1169{
1170 WARN_ON(mcs & ~0xF);
1171 WARN_ON((nss - 1) & ~0x7);
1172 rate->idx = ((nss - 1) << 4) | mcs;
1173}
1174
1175static inline u8
1176ieee80211_rate_get_vht_mcs(const struct ieee80211_tx_rate *rate)
1177{
1178 return rate->idx & 0xF;
1179}
1180
1181static inline u8
1182ieee80211_rate_get_vht_nss(const struct ieee80211_tx_rate *rate)
1183{
1184 return (rate->idx >> 4) + 1;
1185}
1186
1187/**
1188 * struct ieee80211_tx_info - skb transmit information
1189 *
1190 * This structure is placed in skb->cb for three uses:
1191 * (1) mac80211 TX control - mac80211 tells the driver what to do
1192 * (2) driver internal use (if applicable)
1193 * (3) TX status information - driver tells mac80211 what happened
1194 *
1195 * @flags: transmit info flags, defined above
1196 * @band: the band to transmit on (use e.g. for checking for races),
1197 * not valid if the interface is an MLD since we won't know which
1198 * link the frame will be transmitted on
1199 * @hw_queue: HW queue to put the frame on, skb_get_queue_mapping() gives the AC
1200 * @status_data: internal data for TX status handling, assigned privately,
1201 * see also &enum ieee80211_status_data for the internal documentation
1202 * @status_data_idr: indicates status data is IDR allocated ID for ack frame
1203 * @tx_time_est: TX time estimate in units of 4us, used internally
1204 * @control: union part for control data
1205 * @control.rates: TX rates array to try
1206 * @control.rts_cts_rate_idx: rate for RTS or CTS
1207 * @control.use_rts: use RTS
1208 * @control.use_cts_prot: use RTS/CTS
1209 * @control.short_preamble: use short preamble (CCK only)
1210 * @control.skip_table: skip externally configured rate table
1211 * @control.jiffies: timestamp for expiry on powersave clients
1212 * @control.vif: virtual interface (may be NULL)
1213 * @control.hw_key: key to encrypt with (may be NULL)
1214 * @control.flags: control flags, see &enum mac80211_tx_control_flags
1215 * @control.enqueue_time: enqueue time (for iTXQs)
1216 * @driver_rates: alias to @control.rates to reserve space
1217 * @pad: padding
1218 * @rate_driver_data: driver use area if driver needs @control.rates
1219 * @status: union part for status data
1220 * @status.rates: attempted rates
1221 * @status.ack_signal: ACK signal
1222 * @status.ampdu_ack_len: AMPDU ack length
1223 * @status.ampdu_len: AMPDU length
1224 * @status.antenna: (legacy, kept only for iwlegacy)
1225 * @status.tx_time: airtime consumed for transmission; note this is only
1226 * used for WMM AC, not for airtime fairness
1227 * @status.flags: status flags, see &enum mac80211_tx_status_flags
1228 * @status.status_driver_data: driver use area
1229 * @ack: union part for pure ACK data
1230 * @ack.cookie: cookie for the ACK
1231 * @driver_data: array of driver_data pointers
1232 */
1233struct ieee80211_tx_info {
1234 /* common information */
1235 u32 flags;
1236 u32 band:3,
1237 status_data_idr:1,
1238 status_data:13,
1239 hw_queue:4,
1240 tx_time_est:10;
1241 /* 1 free bit */
1242
1243 union {
1244 struct {
1245 union {
1246 /* rate control */
1247 struct {
1248 struct ieee80211_tx_rate rates[
1249 IEEE80211_TX_MAX_RATES];
1250 s8 rts_cts_rate_idx;
1251 u8 use_rts:1;
1252 u8 use_cts_prot:1;
1253 u8 short_preamble:1;
1254 u8 skip_table:1;
1255
1256 /* for injection only (bitmap) */
1257 u8 antennas:2;
1258
1259 /* 14 bits free */
1260 };
1261 /* only needed before rate control */
1262 unsigned long jiffies;
1263 };
1264 /* NB: vif can be NULL for injected frames */
1265 struct ieee80211_vif *vif;
1266 struct ieee80211_key_conf *hw_key;
1267 u32 flags;
1268 codel_time_t enqueue_time;
1269 } control;
1270 struct {
1271 u64 cookie;
1272 } ack;
1273 struct {
1274 struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
1275 s32 ack_signal;
1276 u8 ampdu_ack_len;
1277 u8 ampdu_len;
1278 u8 antenna;
1279 u8 pad;
1280 u16 tx_time;
1281 u8 flags;
1282 u8 pad2;
1283 void *status_driver_data[16 / sizeof(void *)];
1284 } status;
1285 struct {
1286 struct ieee80211_tx_rate driver_rates[
1287 IEEE80211_TX_MAX_RATES];
1288 u8 pad[4];
1289
1290 void *rate_driver_data[
1291 IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
1292 };
1293 void *driver_data[
1294 IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
1295 };
1296};
1297
1298static inline u16
1299ieee80211_info_set_tx_time_est(struct ieee80211_tx_info *info, u16 tx_time_est)
1300{
1301 /* We only have 10 bits in tx_time_est, so store airtime
1302 * in increments of 4us and clamp the maximum to 2**12-1
1303 */
1304 info->tx_time_est = min_t(u16, tx_time_est, 4095) >> 2;
1305 return info->tx_time_est << 2;
1306}
1307
1308static inline u16
1309ieee80211_info_get_tx_time_est(struct ieee80211_tx_info *info)
1310{
1311 return info->tx_time_est << 2;
1312}
1313
1314/***
1315 * struct ieee80211_rate_status - mrr stage for status path
1316 *
1317 * This struct is used in struct ieee80211_tx_status to provide drivers a
1318 * dynamic way to report about used rates and power levels per packet.
1319 *
1320 * @rate_idx The actual used rate.
1321 * @try_count How often the rate was tried.
1322 * @tx_power_idx An idx into the ieee80211_hw->tx_power_levels list of the
1323 * corresponding wifi hardware. The idx shall point to the power level
1324 * that was used when sending the packet.
1325 */
1326struct ieee80211_rate_status {
1327 struct rate_info rate_idx;
1328 u8 try_count;
1329 u8 tx_power_idx;
1330};
1331
1332/**
1333 * struct ieee80211_tx_status - extended tx status info for rate control
1334 *
1335 * @sta: Station that the packet was transmitted for
1336 * @info: Basic tx status information
1337 * @skb: Packet skb (can be NULL if not provided by the driver)
1338 * @rates: Mrr stages that were used when sending the packet
1339 * @n_rates: Number of mrr stages (count of instances for @rates)
1340 * @free_list: list where processed skbs are stored to be free'd by the driver
1341 * @ack_hwtstamp: Hardware timestamp of the received ack in nanoseconds
1342 * Only needed for Timing measurement and Fine timing measurement action
1343 * frames. Only reported by devices that have timestamping enabled.
1344 */
1345struct ieee80211_tx_status {
1346 struct ieee80211_sta *sta;
1347 struct ieee80211_tx_info *info;
1348 struct sk_buff *skb;
1349 struct ieee80211_rate_status *rates;
1350 ktime_t ack_hwtstamp;
1351 u8 n_rates;
1352
1353 struct list_head *free_list;
1354};
1355
1356/**
1357 * struct ieee80211_scan_ies - descriptors for different blocks of IEs
1358 *
1359 * This structure is used to point to different blocks of IEs in HW scan
1360 * and scheduled scan. These blocks contain the IEs passed by userspace
1361 * and the ones generated by mac80211.
1362 *
1363 * @ies: pointers to band specific IEs.
1364 * @len: lengths of band_specific IEs.
1365 * @common_ies: IEs for all bands (especially vendor specific ones)
1366 * @common_ie_len: length of the common_ies
1367 */
1368struct ieee80211_scan_ies {
1369 const u8 *ies[NUM_NL80211_BANDS];
1370 size_t len[NUM_NL80211_BANDS];
1371 const u8 *common_ies;
1372 size_t common_ie_len;
1373};
1374
1375
1376static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
1377{
1378 return (struct ieee80211_tx_info *)skb->cb;
1379}
1380
1381static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb)
1382{
1383 return (struct ieee80211_rx_status *)skb->cb;
1384}
1385
1386/**
1387 * ieee80211_tx_info_clear_status - clear TX status
1388 *
1389 * @info: The &struct ieee80211_tx_info to be cleared.
1390 *
1391 * When the driver passes an skb back to mac80211, it must report
1392 * a number of things in TX status. This function clears everything
1393 * in the TX status but the rate control information (it does clear
1394 * the count since you need to fill that in anyway).
1395 *
1396 * NOTE: While the rates array is kept intact, this will wipe all of the
1397 * driver_data fields in info, so it's up to the driver to restore
1398 * any fields it needs after calling this helper.
1399 */
1400static inline void
1401ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
1402{
1403 int i;
1404
1405 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
1406 offsetof(struct ieee80211_tx_info, control.rates));
1407 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
1408 offsetof(struct ieee80211_tx_info, driver_rates));
1409 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
1410 /* clear the rate counts */
1411 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
1412 info->status.rates[i].count = 0;
1413 memset_after(&info->status, 0, rates);
1414}
1415
1416
1417/**
1418 * enum mac80211_rx_flags - receive flags
1419 *
1420 * These flags are used with the @flag member of &struct ieee80211_rx_status.
1421 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
1422 * Use together with %RX_FLAG_MMIC_STRIPPED.
1423 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
1424 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
1425 * verification has been done by the hardware.
1426 * @RX_FLAG_IV_STRIPPED: The IV and ICV are stripped from this frame.
1427 * If this flag is set, the stack cannot do any replay detection
1428 * hence the driver or hardware will have to do that.
1429 * @RX_FLAG_PN_VALIDATED: Currently only valid for CCMP/GCMP frames, this
1430 * flag indicates that the PN was verified for replay protection.
1431 * Note that this flag is also currently only supported when a frame
1432 * is also decrypted (ie. @RX_FLAG_DECRYPTED must be set)
1433 * @RX_FLAG_DUP_VALIDATED: The driver should set this flag if it did
1434 * de-duplication by itself.
1435 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
1436 * the frame.
1437 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
1438 * the frame.
1439 * @RX_FLAG_MACTIME: The timestamp passed in the RX status (@mactime
1440 * field) is valid if this field is non-zero, and the position
1441 * where the timestamp was sampled depends on the value.
1442 * @RX_FLAG_MACTIME_START: The timestamp passed in the RX status (@mactime
1443 * field) is valid and contains the time the first symbol of the MPDU
1444 * was received. This is useful in monitor mode and for proper IBSS
1445 * merging.
1446 * @RX_FLAG_MACTIME_END: The timestamp passed in the RX status (@mactime
1447 * field) is valid and contains the time the last symbol of the MPDU
1448 * (including FCS) was received.
1449 * @RX_FLAG_MACTIME_PLCP_START: The timestamp passed in the RX status (@mactime
1450 * field) is valid and contains the time the SYNC preamble was received.
1451 * @RX_FLAG_MACTIME_IS_RTAP_TS64: The timestamp passed in the RX status @mactime
1452 * is only for use in the radiotap timestamp header, not otherwise a valid
1453 * @mactime value. Note this is a separate flag so that we continue to see
1454 * %RX_FLAG_MACTIME as unset. Also note that in this case the timestamp is
1455 * reported to be 64 bits wide, not just 32.
1456 * @RX_FLAG_NO_SIGNAL_VAL: The signal strength value is not present.
1457 * Valid only for data frames (mainly A-MPDU)
1458 * @RX_FLAG_AMPDU_DETAILS: A-MPDU details are known, in particular the reference
1459 * number (@ampdu_reference) must be populated and be a distinct number for
1460 * each A-MPDU
1461 * @RX_FLAG_AMPDU_LAST_KNOWN: last subframe is known, should be set on all
1462 * subframes of a single A-MPDU
1463 * @RX_FLAG_AMPDU_IS_LAST: this subframe is the last subframe of the A-MPDU
1464 * @RX_FLAG_AMPDU_DELIM_CRC_ERROR: A delimiter CRC error has been detected
1465 * on this subframe
1466 * @RX_FLAG_MIC_STRIPPED: The mic was stripped of this packet. Decryption was
1467 * done by the hardware
1468 * @RX_FLAG_ONLY_MONITOR: Report frame only to monitor interfaces without
1469 * processing it in any regular way.
1470 * This is useful if drivers offload some frames but still want to report
1471 * them for sniffing purposes.
1472 * @RX_FLAG_SKIP_MONITOR: Process and report frame to all interfaces except
1473 * monitor interfaces.
1474 * This is useful if drivers offload some frames but still want to report
1475 * them for sniffing purposes.
1476 * @RX_FLAG_AMSDU_MORE: Some drivers may prefer to report separate A-MSDU
1477 * subframes instead of a one huge frame for performance reasons.
1478 * All, but the last MSDU from an A-MSDU should have this flag set. E.g.
1479 * if an A-MSDU has 3 frames, the first 2 must have the flag set, while
1480 * the 3rd (last) one must not have this flag set. The flag is used to
1481 * deal with retransmission/duplication recovery properly since A-MSDU
1482 * subframes share the same sequence number. Reported subframes can be
1483 * either regular MSDU or singly A-MSDUs. Subframes must not be
1484 * interleaved with other frames.
1485 * @RX_FLAG_RADIOTAP_TLV_AT_END: This frame contains radiotap TLVs in the
1486 * skb->data (before the 802.11 header).
1487 * If used, the SKB's mac_header pointer must be set to point
1488 * to the 802.11 header after the TLVs, and any padding added after TLV
1489 * data to align to 4 must be cleared by the driver putting the TLVs
1490 * in the skb.
1491 * @RX_FLAG_ALLOW_SAME_PN: Allow the same PN as same packet before.
1492 * This is used for AMSDU subframes which can have the same PN as
1493 * the first subframe.
1494 * @RX_FLAG_ICV_STRIPPED: The ICV is stripped from this frame. CRC checking must
1495 * be done in the hardware.
1496 * @RX_FLAG_AMPDU_EOF_BIT: Value of the EOF bit in the A-MPDU delimiter for this
1497 * frame
1498 * @RX_FLAG_AMPDU_EOF_BIT_KNOWN: The EOF value is known
1499 * @RX_FLAG_RADIOTAP_HE: HE radiotap data is present
1500 * (&struct ieee80211_radiotap_he, mac80211 will fill in
1501 *
1502 * - DATA3_DATA_MCS
1503 * - DATA3_DATA_DCM
1504 * - DATA3_CODING
1505 * - DATA5_GI
1506 * - DATA5_DATA_BW_RU_ALLOC
1507 * - DATA6_NSTS
1508 * - DATA3_STBC
1509 *
1510 * from the RX info data, so leave those zeroed when building this data)
1511 * @RX_FLAG_RADIOTAP_HE_MU: HE MU radiotap data is present
1512 * (&struct ieee80211_radiotap_he_mu)
1513 * @RX_FLAG_RADIOTAP_LSIG: L-SIG radiotap data is present
1514 * @RX_FLAG_NO_PSDU: use the frame only for radiotap reporting, with
1515 * the "0-length PSDU" field included there. The value for it is
1516 * in &struct ieee80211_rx_status. Note that if this value isn't
1517 * known the frame shouldn't be reported.
1518 * @RX_FLAG_8023: the frame has an 802.3 header (decap offload performed by
1519 * hardware or driver)
1520 */
1521enum mac80211_rx_flags {
1522 RX_FLAG_MMIC_ERROR = BIT(0),
1523 RX_FLAG_DECRYPTED = BIT(1),
1524 RX_FLAG_ONLY_MONITOR = BIT(2),
1525 RX_FLAG_MMIC_STRIPPED = BIT(3),
1526 RX_FLAG_IV_STRIPPED = BIT(4),
1527 RX_FLAG_FAILED_FCS_CRC = BIT(5),
1528 RX_FLAG_FAILED_PLCP_CRC = BIT(6),
1529 RX_FLAG_MACTIME_IS_RTAP_TS64 = BIT(7),
1530 RX_FLAG_NO_SIGNAL_VAL = BIT(8),
1531 RX_FLAG_AMPDU_DETAILS = BIT(9),
1532 RX_FLAG_PN_VALIDATED = BIT(10),
1533 RX_FLAG_DUP_VALIDATED = BIT(11),
1534 RX_FLAG_AMPDU_LAST_KNOWN = BIT(12),
1535 RX_FLAG_AMPDU_IS_LAST = BIT(13),
1536 RX_FLAG_AMPDU_DELIM_CRC_ERROR = BIT(14),
1537 /* one free bit at 15 */
1538 RX_FLAG_MACTIME = BIT(16) | BIT(17),
1539 RX_FLAG_MACTIME_PLCP_START = 1 << 16,
1540 RX_FLAG_MACTIME_START = 2 << 16,
1541 RX_FLAG_MACTIME_END = 3 << 16,
1542 RX_FLAG_SKIP_MONITOR = BIT(18),
1543 RX_FLAG_AMSDU_MORE = BIT(19),
1544 RX_FLAG_RADIOTAP_TLV_AT_END = BIT(20),
1545 RX_FLAG_MIC_STRIPPED = BIT(21),
1546 RX_FLAG_ALLOW_SAME_PN = BIT(22),
1547 RX_FLAG_ICV_STRIPPED = BIT(23),
1548 RX_FLAG_AMPDU_EOF_BIT = BIT(24),
1549 RX_FLAG_AMPDU_EOF_BIT_KNOWN = BIT(25),
1550 RX_FLAG_RADIOTAP_HE = BIT(26),
1551 RX_FLAG_RADIOTAP_HE_MU = BIT(27),
1552 RX_FLAG_RADIOTAP_LSIG = BIT(28),
1553 RX_FLAG_NO_PSDU = BIT(29),
1554 RX_FLAG_8023 = BIT(30),
1555};
1556
1557/**
1558 * enum mac80211_rx_encoding_flags - MCS & bandwidth flags
1559 *
1560 * @RX_ENC_FLAG_SHORTPRE: Short preamble was used for this frame
1561 * @RX_ENC_FLAG_SHORT_GI: Short guard interval was used
1562 * @RX_ENC_FLAG_HT_GF: This frame was received in a HT-greenfield transmission,
1563 * if the driver fills this value it should add
1564 * %IEEE80211_RADIOTAP_MCS_HAVE_FMT
1565 * to @hw.radiotap_mcs_details to advertise that fact.
1566 * @RX_ENC_FLAG_LDPC: LDPC was used
1567 * @RX_ENC_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
1568 * @RX_ENC_FLAG_BF: packet was beamformed
1569 */
1570enum mac80211_rx_encoding_flags {
1571 RX_ENC_FLAG_SHORTPRE = BIT(0),
1572 RX_ENC_FLAG_SHORT_GI = BIT(2),
1573 RX_ENC_FLAG_HT_GF = BIT(3),
1574 RX_ENC_FLAG_STBC_MASK = BIT(4) | BIT(5),
1575 RX_ENC_FLAG_LDPC = BIT(6),
1576 RX_ENC_FLAG_BF = BIT(7),
1577};
1578
1579#define RX_ENC_FLAG_STBC_SHIFT 4
1580
1581enum mac80211_rx_encoding {
1582 RX_ENC_LEGACY = 0,
1583 RX_ENC_HT,
1584 RX_ENC_VHT,
1585 RX_ENC_HE,
1586 RX_ENC_EHT,
1587};
1588
1589/**
1590 * struct ieee80211_rx_status - receive status
1591 *
1592 * The low-level driver should provide this information (the subset
1593 * supported by hardware) to the 802.11 code with each received
1594 * frame, in the skb's control buffer (cb).
1595 *
1596 * @mactime: value in microseconds of the 64-bit Time Synchronization Function
1597 * (TSF) timer when the first data symbol (MPDU) arrived at the hardware.
1598 * @boottime_ns: CLOCK_BOOTTIME timestamp the frame was received at, this is
1599 * needed only for beacons and probe responses that update the scan cache.
1600 * @ack_tx_hwtstamp: Hardware timestamp for the ack TX in nanoseconds. Only
1601 * needed for Timing measurement and Fine timing measurement action frames.
1602 * Only reported by devices that have timestamping enabled.
1603 * @device_timestamp: arbitrary timestamp for the device, mac80211 doesn't use
1604 * it but can store it and pass it back to the driver for synchronisation
1605 * @band: the active band when this frame was received
1606 * @freq: frequency the radio was tuned to when receiving this frame, in MHz
1607 * This field must be set for management frames, but isn't strictly needed
1608 * for data (other) frames - for those it only affects radiotap reporting.
1609 * @freq_offset: @freq has a positive offset of 500Khz.
1610 * @signal: signal strength when receiving this frame, either in dBm, in dB or
1611 * unspecified depending on the hardware capabilities flags
1612 * @IEEE80211_HW_SIGNAL_*
1613 * @chains: bitmask of receive chains for which separate signal strength
1614 * values were filled.
1615 * @chain_signal: per-chain signal strength, in dBm (unlike @signal, doesn't
1616 * support dB or unspecified units)
1617 * @antenna: antenna used
1618 * @rate_idx: index of data rate into band's supported rates or MCS index if
1619 * HT or VHT is used (%RX_FLAG_HT/%RX_FLAG_VHT)
1620 * @nss: number of streams (VHT, HE and EHT only)
1621 * @flag: %RX_FLAG_\*
1622 * @encoding: &enum mac80211_rx_encoding
1623 * @bw: &enum rate_info_bw
1624 * @enc_flags: uses bits from &enum mac80211_rx_encoding_flags
1625 * @he_ru: HE RU, from &enum nl80211_he_ru_alloc
1626 * @he_gi: HE GI, from &enum nl80211_he_gi
1627 * @he_dcm: HE DCM value
1628 * @eht: EHT specific rate information
1629 * @eht.ru: EHT RU, from &enum nl80211_eht_ru_alloc
1630 * @eht.gi: EHT GI, from &enum nl80211_eht_gi
1631 * @rx_flags: internal RX flags for mac80211
1632 * @ampdu_reference: A-MPDU reference number, must be a different value for
1633 * each A-MPDU but the same for each subframe within one A-MPDU
1634 * @zero_length_psdu_type: radiotap type of the 0-length PSDU
1635 * @link_valid: if the link which is identified by @link_id is valid. This flag
1636 * is set only when connection is MLO.
1637 * @link_id: id of the link used to receive the packet. This is used along with
1638 * @link_valid.
1639 */
1640struct ieee80211_rx_status {
1641 u64 mactime;
1642 union {
1643 u64 boottime_ns;
1644 ktime_t ack_tx_hwtstamp;
1645 };
1646 u32 device_timestamp;
1647 u32 ampdu_reference;
1648 u32 flag;
1649 u16 freq: 13, freq_offset: 1;
1650 u8 enc_flags;
1651 u8 encoding:3, bw:4;
1652 union {
1653 struct {
1654 u8 he_ru:3;
1655 u8 he_gi:2;
1656 u8 he_dcm:1;
1657 };
1658 struct {
1659 u8 ru:4;
1660 u8 gi:2;
1661 } eht;
1662 };
1663 u8 rate_idx;
1664 u8 nss;
1665 u8 rx_flags;
1666 u8 band;
1667 u8 antenna;
1668 s8 signal;
1669 u8 chains;
1670 s8 chain_signal[IEEE80211_MAX_CHAINS];
1671 u8 zero_length_psdu_type;
1672 u8 link_valid:1, link_id:4;
1673};
1674
1675static inline u32
1676ieee80211_rx_status_to_khz(struct ieee80211_rx_status *rx_status)
1677{
1678 return MHZ_TO_KHZ(rx_status->freq) +
1679 (rx_status->freq_offset ? 500 : 0);
1680}
1681
1682/**
1683 * enum ieee80211_conf_flags - configuration flags
1684 *
1685 * Flags to define PHY configuration options
1686 *
1687 * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
1688 * to determine for example whether to calculate timestamps for packets
1689 * or not, do not use instead of filter flags!
1690 * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only).
1691 * This is the power save mode defined by IEEE 802.11-2007 section 11.2,
1692 * meaning that the hardware still wakes up for beacons, is able to
1693 * transmit frames and receive the possible acknowledgment frames.
1694 * Not to be confused with hardware specific wakeup/sleep states,
1695 * driver is responsible for that. See the section "Powersave support"
1696 * for more.
1697 * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
1698 * the driver should be prepared to handle configuration requests but
1699 * may turn the device off as much as possible. Typically, this flag will
1700 * be set when an interface is set UP but not associated or scanning, but
1701 * it can also be unset in that case when monitor interfaces are active.
1702 * @IEEE80211_CONF_OFFCHANNEL: The device is currently not on its main
1703 * operating channel.
1704 */
1705enum ieee80211_conf_flags {
1706 IEEE80211_CONF_MONITOR = (1<<0),
1707 IEEE80211_CONF_PS = (1<<1),
1708 IEEE80211_CONF_IDLE = (1<<2),
1709 IEEE80211_CONF_OFFCHANNEL = (1<<3),
1710};
1711
1712
1713/**
1714 * enum ieee80211_conf_changed - denotes which configuration changed
1715 *
1716 * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
1717 * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed
1718 * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
1719 * @IEEE80211_CONF_CHANGE_POWER: the TX power changed
1720 * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
1721 * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
1722 * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
1723 * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
1724 * Note that this is only valid if channel contexts are not used,
1725 * otherwise each channel context has the number of chains listed.
1726 */
1727enum ieee80211_conf_changed {
1728 IEEE80211_CONF_CHANGE_SMPS = BIT(1),
1729 IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2),
1730 IEEE80211_CONF_CHANGE_MONITOR = BIT(3),
1731 IEEE80211_CONF_CHANGE_PS = BIT(4),
1732 IEEE80211_CONF_CHANGE_POWER = BIT(5),
1733 IEEE80211_CONF_CHANGE_CHANNEL = BIT(6),
1734 IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(7),
1735 IEEE80211_CONF_CHANGE_IDLE = BIT(8),
1736};
1737
1738/**
1739 * enum ieee80211_smps_mode - spatial multiplexing power save mode
1740 *
1741 * @IEEE80211_SMPS_AUTOMATIC: automatic
1742 * @IEEE80211_SMPS_OFF: off
1743 * @IEEE80211_SMPS_STATIC: static
1744 * @IEEE80211_SMPS_DYNAMIC: dynamic
1745 * @IEEE80211_SMPS_NUM_MODES: internal, don't use
1746 */
1747enum ieee80211_smps_mode {
1748 IEEE80211_SMPS_AUTOMATIC,
1749 IEEE80211_SMPS_OFF,
1750 IEEE80211_SMPS_STATIC,
1751 IEEE80211_SMPS_DYNAMIC,
1752
1753 /* keep last */
1754 IEEE80211_SMPS_NUM_MODES,
1755};
1756
1757/**
1758 * struct ieee80211_conf - configuration of the device
1759 *
1760 * This struct indicates how the driver shall configure the hardware.
1761 *
1762 * @flags: configuration flags defined above
1763 *
1764 * @listen_interval: listen interval in units of beacon interval
1765 * @ps_dtim_period: The DTIM period of the AP we're connected to, for use
1766 * in power saving. Power saving will not be enabled until a beacon
1767 * has been received and the DTIM period is known.
1768 * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
1769 * powersave documentation below. This variable is valid only when
1770 * the CONF_PS flag is set.
1771 *
1772 * @power_level: requested transmit power (in dBm), backward compatibility
1773 * value only that is set to the minimum of all interfaces
1774 *
1775 * @chandef: the channel definition to tune to
1776 * @radar_enabled: whether radar detection is enabled
1777 *
1778 * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
1779 * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
1780 * but actually means the number of transmissions not the number of retries
1781 * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
1782 * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
1783 * number of transmissions not the number of retries
1784 *
1785 * @smps_mode: spatial multiplexing powersave mode; note that
1786 * %IEEE80211_SMPS_STATIC is used when the device is not
1787 * configured for an HT channel.
1788 * Note that this is only valid if channel contexts are not used,
1789 * otherwise each channel context has the number of chains listed.
1790 */
1791struct ieee80211_conf {
1792 u32 flags;
1793 int power_level, dynamic_ps_timeout;
1794
1795 u16 listen_interval;
1796 u8 ps_dtim_period;
1797
1798 u8 long_frame_max_tx_count, short_frame_max_tx_count;
1799
1800 struct cfg80211_chan_def chandef;
1801 bool radar_enabled;
1802 enum ieee80211_smps_mode smps_mode;
1803};
1804
1805/**
1806 * struct ieee80211_channel_switch - holds the channel switch data
1807 *
1808 * The information provided in this structure is required for channel switch
1809 * operation.
1810 *
1811 * @timestamp: value in microseconds of the 64-bit Time Synchronization
1812 * Function (TSF) timer when the frame containing the channel switch
1813 * announcement was received. This is simply the rx.mactime parameter
1814 * the driver passed into mac80211.
1815 * @device_timestamp: arbitrary timestamp for the device, this is the
1816 * rx.device_timestamp parameter the driver passed to mac80211.
1817 * @block_tx: Indicates whether transmission must be blocked before the
1818 * scheduled channel switch, as indicated by the AP.
1819 * @chandef: the new channel to switch to
1820 * @count: the number of TBTT's until the channel switch event
1821 * @delay: maximum delay between the time the AP transmitted the last beacon in
1822 * current channel and the expected time of the first beacon in the new
1823 * channel, expressed in TU.
1824 * @link_id: the link ID of the link doing the channel switch, 0 for non-MLO
1825 */
1826struct ieee80211_channel_switch {
1827 u64 timestamp;
1828 u32 device_timestamp;
1829 bool block_tx;
1830 struct cfg80211_chan_def chandef;
1831 u8 count;
1832 u8 link_id;
1833 u32 delay;
1834};
1835
1836/**
1837 * enum ieee80211_vif_flags - virtual interface flags
1838 *
1839 * @IEEE80211_VIF_BEACON_FILTER: the device performs beacon filtering
1840 * on this virtual interface to avoid unnecessary CPU wakeups
1841 * @IEEE80211_VIF_SUPPORTS_CQM_RSSI: the device can do connection quality
1842 * monitoring on this virtual interface -- i.e. it can monitor
1843 * connection quality related parameters, such as the RSSI level and
1844 * provide notifications if configured trigger levels are reached.
1845 * @IEEE80211_VIF_SUPPORTS_UAPSD: The device can do U-APSD for this
1846 * interface. This flag should be set during interface addition,
1847 * but may be set/cleared as late as authentication to an AP. It is
1848 * only valid for managed/station mode interfaces.
1849 * @IEEE80211_VIF_GET_NOA_UPDATE: request to handle NOA attributes
1850 * and send P2P_PS notification to the driver if NOA changed, even
1851 * this is not pure P2P vif.
1852 * @IEEE80211_VIF_EML_ACTIVE: The driver indicates that EML operation is
1853 * enabled for the interface.
1854 * @IEEE80211_VIF_IGNORE_OFDMA_WIDER_BW: Ignore wider bandwidth OFDMA
1855 * operation on this interface and request a channel context without
1856 * the AP definition. Use this e.g. because the device is able to
1857 * handle OFDMA (downlink and trigger for uplink) on a per-AP basis.
1858 */
1859enum ieee80211_vif_flags {
1860 IEEE80211_VIF_BEACON_FILTER = BIT(0),
1861 IEEE80211_VIF_SUPPORTS_CQM_RSSI = BIT(1),
1862 IEEE80211_VIF_SUPPORTS_UAPSD = BIT(2),
1863 IEEE80211_VIF_GET_NOA_UPDATE = BIT(3),
1864 IEEE80211_VIF_EML_ACTIVE = BIT(4),
1865 IEEE80211_VIF_IGNORE_OFDMA_WIDER_BW = BIT(5),
1866};
1867
1868
1869/**
1870 * enum ieee80211_offload_flags - virtual interface offload flags
1871 *
1872 * @IEEE80211_OFFLOAD_ENCAP_ENABLED: tx encapsulation offload is enabled
1873 * The driver supports sending frames passed as 802.3 frames by mac80211.
1874 * It must also support sending 802.11 packets for the same interface.
1875 * @IEEE80211_OFFLOAD_ENCAP_4ADDR: support 4-address mode encapsulation offload
1876 * @IEEE80211_OFFLOAD_DECAP_ENABLED: rx encapsulation offload is enabled
1877 * The driver supports passing received 802.11 frames as 802.3 frames to
1878 * mac80211.
1879 */
1880
1881enum ieee80211_offload_flags {
1882 IEEE80211_OFFLOAD_ENCAP_ENABLED = BIT(0),
1883 IEEE80211_OFFLOAD_ENCAP_4ADDR = BIT(1),
1884 IEEE80211_OFFLOAD_DECAP_ENABLED = BIT(2),
1885};
1886
1887/**
1888 * struct ieee80211_vif_cfg - interface configuration
1889 * @assoc: association status
1890 * @ibss_joined: indicates whether this station is part of an IBSS or not
1891 * @ibss_creator: indicates if a new IBSS network is being created
1892 * @ps: power-save mode (STA only). This flag is NOT affected by
1893 * offchannel/dynamic_ps operations.
1894 * @aid: association ID number, valid only when @assoc is true
1895 * @eml_cap: EML capabilities as described in P802.11be_D4.1 Figure 9-1001j.
1896 * @eml_med_sync_delay: Medium Synchronization delay as described in
1897 * P802.11be_D4.1 Figure 9-1001i.
1898 * @mld_capa_op: MLD Capabilities and Operations per P802.11be_D4.1
1899 * Figure 9-1001k
1900 * @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The
1901 * may filter ARP queries targeted for other addresses than listed here.
1902 * The driver must allow ARP queries targeted for all address listed here
1903 * to pass through. An empty list implies no ARP queries need to pass.
1904 * @arp_addr_cnt: Number of addresses currently on the list. Note that this
1905 * may be larger than %IEEE80211_BSS_ARP_ADDR_LIST_LEN (the arp_addr_list
1906 * array size), it's up to the driver what to do in that case.
1907 * @ssid: The SSID of the current vif. Valid in AP and IBSS mode.
1908 * @ssid_len: Length of SSID given in @ssid.
1909 * @s1g: BSS is S1G BSS (affects Association Request format).
1910 * @idle: This interface is idle. There's also a global idle flag in the
1911 * hardware config which may be more appropriate depending on what
1912 * your driver/device needs to do.
1913 * @ap_addr: AP MLD address, or BSSID for non-MLO connections
1914 * (station mode only)
1915 */
1916struct ieee80211_vif_cfg {
1917 /* association related data */
1918 bool assoc, ibss_joined;
1919 bool ibss_creator;
1920 bool ps;
1921 u16 aid;
1922 u16 eml_cap;
1923 u16 eml_med_sync_delay;
1924 u16 mld_capa_op;
1925
1926 __be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN];
1927 int arp_addr_cnt;
1928 u8 ssid[IEEE80211_MAX_SSID_LEN];
1929 size_t ssid_len;
1930 bool s1g;
1931 bool idle;
1932 u8 ap_addr[ETH_ALEN] __aligned(2);
1933};
1934
1935#define IEEE80211_TTLM_NUM_TIDS 8
1936
1937/**
1938 * struct ieee80211_neg_ttlm - negotiated TID to link map info
1939 *
1940 * @downlink: bitmap of active links per TID for downlink, or 0 if mapping for
1941 * this TID is not included.
1942 * @uplink: bitmap of active links per TID for uplink, or 0 if mapping for this
1943 * TID is not included.
1944 * @valid: info is valid or not.
1945 */
1946struct ieee80211_neg_ttlm {
1947 u16 downlink[IEEE80211_TTLM_NUM_TIDS];
1948 u16 uplink[IEEE80211_TTLM_NUM_TIDS];
1949 bool valid;
1950};
1951
1952/**
1953 * enum ieee80211_neg_ttlm_res - return value for negotiated TTLM handling
1954 * @NEG_TTLM_RES_ACCEPT: accept the request
1955 * @NEG_TTLM_RES_REJECT: reject the request
1956 * @NEG_TTLM_RES_SUGGEST_PREFERRED: reject and suggest a new mapping
1957 */
1958enum ieee80211_neg_ttlm_res {
1959 NEG_TTLM_RES_ACCEPT,
1960 NEG_TTLM_RES_REJECT,
1961 NEG_TTLM_RES_SUGGEST_PREFERRED
1962};
1963
1964/**
1965 * struct ieee80211_vif - per-interface data
1966 *
1967 * Data in this structure is continually present for driver
1968 * use during the life of a virtual interface.
1969 *
1970 * @type: type of this virtual interface
1971 * @cfg: vif configuration, see &struct ieee80211_vif_cfg
1972 * @bss_conf: BSS configuration for this interface, either our own
1973 * or the BSS we're associated to
1974 * @link_conf: in case of MLD, the per-link BSS configuration,
1975 * indexed by link ID
1976 * @valid_links: bitmap of valid links, or 0 for non-MLO.
1977 * @active_links: The bitmap of active links, or 0 for non-MLO.
1978 * The driver shouldn't change this directly, but use the
1979 * API calls meant for that purpose.
1980 * @dormant_links: subset of the valid links that are disabled/suspended
1981 * due to advertised or negotiated TTLM respectively.
1982 * 0 for non-MLO.
1983 * @suspended_links: subset of dormant_links representing links that are
1984 * suspended due to negotiated TTLM, and could be activated in the
1985 * future by tearing down the TTLM negotiation.
1986 * 0 for non-MLO.
1987 * @neg_ttlm: negotiated TID to link mapping info.
1988 * see &struct ieee80211_neg_ttlm.
1989 * @addr: address of this interface
1990 * @addr_valid: indicates if the address is actively used. Set to false for
1991 * passive monitor interfaces, true in all other cases.
1992 * @p2p: indicates whether this AP or STA interface is a p2p
1993 * interface, i.e. a GO or p2p-sta respectively
1994 * @netdev_features: tx netdev features supported by the hardware for this
1995 * vif. mac80211 initializes this to hw->netdev_features, and the driver
1996 * can mask out specific tx features. mac80211 will handle software fixup
1997 * for masked offloads (GSO, CSUM)
1998 * @driver_flags: flags/capabilities the driver has for this interface,
1999 * these need to be set (or cleared) when the interface is added
2000 * or, if supported by the driver, the interface type is changed
2001 * at runtime, mac80211 will never touch this field
2002 * @offload_flags: hardware offload capabilities/flags for this interface.
2003 * These are initialized by mac80211 before calling .add_interface,
2004 * .change_interface or .update_vif_offload and updated by the driver
2005 * within these ops, based on supported features or runtime change
2006 * restrictions.
2007 * @hw_queue: hardware queue for each AC
2008 * @cab_queue: content-after-beacon (DTIM beacon really) queue, AP mode only
2009 * @debugfs_dir: debugfs dentry, can be used by drivers to create own per
2010 * interface debug files. Note that it will be NULL for the virtual
2011 * monitor interface (if that is requested.)
2012 * @probe_req_reg: probe requests should be reported to mac80211 for this
2013 * interface.
2014 * @rx_mcast_action_reg: multicast Action frames should be reported to mac80211
2015 * for this interface.
2016 * @drv_priv: data area for driver use, will always be aligned to
2017 * sizeof(void \*).
2018 * @txq: the multicast data TX queue
2019 * @offload_flags: 802.3 -> 802.11 enapsulation offload flags, see
2020 * &enum ieee80211_offload_flags.
2021 * @mbssid_tx_vif: Pointer to the transmitting interface if MBSSID is enabled.
2022 */
2023struct ieee80211_vif {
2024 enum nl80211_iftype type;
2025 struct ieee80211_vif_cfg cfg;
2026 struct ieee80211_bss_conf bss_conf;
2027 struct ieee80211_bss_conf __rcu *link_conf[IEEE80211_MLD_MAX_NUM_LINKS];
2028 u16 valid_links, active_links, dormant_links, suspended_links;
2029 struct ieee80211_neg_ttlm neg_ttlm;
2030 u8 addr[ETH_ALEN] __aligned(2);
2031 bool addr_valid;
2032 bool p2p;
2033
2034 u8 cab_queue;
2035 u8 hw_queue[IEEE80211_NUM_ACS];
2036
2037 struct ieee80211_txq *txq;
2038
2039 netdev_features_t netdev_features;
2040 u32 driver_flags;
2041 u32 offload_flags;
2042
2043#ifdef CONFIG_MAC80211_DEBUGFS
2044 struct dentry *debugfs_dir;
2045#endif
2046
2047 bool probe_req_reg;
2048 bool rx_mcast_action_reg;
2049
2050 struct ieee80211_vif *mbssid_tx_vif;
2051
2052 /* must be last */
2053 u8 drv_priv[] __aligned(sizeof(void *));
2054};
2055
2056/**
2057 * ieee80211_vif_usable_links - Return the usable links for the vif
2058 * @vif: the vif for which the usable links are requested
2059 * Return: the usable link bitmap
2060 */
2061static inline u16 ieee80211_vif_usable_links(const struct ieee80211_vif *vif)
2062{
2063 return vif->valid_links & ~vif->dormant_links;
2064}
2065
2066/**
2067 * ieee80211_vif_is_mld - Returns true iff the vif is an MLD one
2068 * @vif: the vif
2069 * Return: %true if the vif is an MLD, %false otherwise.
2070 */
2071static inline bool ieee80211_vif_is_mld(const struct ieee80211_vif *vif)
2072{
2073 /* valid_links != 0 indicates this vif is an MLD */
2074 return vif->valid_links != 0;
2075}
2076
2077/**
2078 * ieee80211_vif_link_active - check if a given link is active
2079 * @vif: the vif
2080 * @link_id: the link ID to check
2081 * Return: %true if the vif is an MLD and the link is active, or if
2082 * the vif is not an MLD and the link ID is 0; %false otherwise.
2083 */
2084static inline bool ieee80211_vif_link_active(const struct ieee80211_vif *vif,
2085 unsigned int link_id)
2086{
2087 if (!ieee80211_vif_is_mld(vif))
2088 return link_id == 0;
2089 return vif->active_links & BIT(link_id);
2090}
2091
2092#define for_each_vif_active_link(vif, link, link_id) \
2093 for (link_id = 0; link_id < ARRAY_SIZE((vif)->link_conf); link_id++) \
2094 if ((!(vif)->active_links || \
2095 (vif)->active_links & BIT(link_id)) && \
2096 (link = link_conf_dereference_check(vif, link_id)))
2097
2098static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
2099{
2100#ifdef CONFIG_MAC80211_MESH
2101 return vif->type == NL80211_IFTYPE_MESH_POINT;
2102#endif
2103 return false;
2104}
2105
2106/**
2107 * wdev_to_ieee80211_vif - return a vif struct from a wdev
2108 * @wdev: the wdev to get the vif for
2109 *
2110 * This can be used by mac80211 drivers with direct cfg80211 APIs
2111 * (like the vendor commands) that get a wdev.
2112 *
2113 * Return: pointer to the wdev, or %NULL if the given wdev isn't
2114 * associated with a vif that the driver knows about (e.g. monitor
2115 * or AP_VLAN interfaces.)
2116 */
2117struct ieee80211_vif *wdev_to_ieee80211_vif(struct wireless_dev *wdev);
2118
2119/**
2120 * ieee80211_vif_to_wdev - return a wdev struct from a vif
2121 * @vif: the vif to get the wdev for
2122 *
2123 * This can be used by mac80211 drivers with direct cfg80211 APIs
2124 * (like the vendor commands) that needs to get the wdev for a vif.
2125 * This can also be useful to get the netdev associated to a vif.
2126 *
2127 * Return: pointer to the wdev
2128 */
2129struct wireless_dev *ieee80211_vif_to_wdev(struct ieee80211_vif *vif);
2130
2131static inline bool lockdep_vif_wiphy_mutex_held(struct ieee80211_vif *vif)
2132{
2133 return lockdep_is_held(&ieee80211_vif_to_wdev(vif)->wiphy->mtx);
2134}
2135
2136#define link_conf_dereference_protected(vif, link_id) \
2137 rcu_dereference_protected((vif)->link_conf[link_id], \
2138 lockdep_vif_wiphy_mutex_held(vif))
2139
2140#define link_conf_dereference_check(vif, link_id) \
2141 rcu_dereference_check((vif)->link_conf[link_id], \
2142 lockdep_vif_wiphy_mutex_held(vif))
2143
2144/**
2145 * enum ieee80211_key_flags - key flags
2146 *
2147 * These flags are used for communication about keys between the driver
2148 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
2149 *
2150 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
2151 * driver to indicate that it requires IV generation for this
2152 * particular key. Setting this flag does not necessarily mean that SKBs
2153 * will have sufficient tailroom for ICV or MIC.
2154 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
2155 * the driver for a TKIP key if it requires Michael MIC
2156 * generation in software.
2157 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
2158 * that the key is pairwise rather then a shared key.
2159 * @IEEE80211_KEY_FLAG_SW_MGMT_TX: This flag should be set by the driver for a
2160 * CCMP/GCMP key if it requires CCMP/GCMP encryption of management frames
2161 * (MFP) to be done in software.
2162 * @IEEE80211_KEY_FLAG_PUT_IV_SPACE: This flag should be set by the driver
2163 * if space should be prepared for the IV, but the IV
2164 * itself should not be generated. Do not set together with
2165 * @IEEE80211_KEY_FLAG_GENERATE_IV on the same key. Setting this flag does
2166 * not necessarily mean that SKBs will have sufficient tailroom for ICV or
2167 * MIC.
2168 * @IEEE80211_KEY_FLAG_RX_MGMT: This key will be used to decrypt received
2169 * management frames. The flag can help drivers that have a hardware
2170 * crypto implementation that doesn't deal with management frames
2171 * properly by allowing them to not upload the keys to hardware and
2172 * fall back to software crypto. Note that this flag deals only with
2173 * RX, if your crypto engine can't deal with TX you can also set the
2174 * %IEEE80211_KEY_FLAG_SW_MGMT_TX flag to encrypt such frames in SW.
2175 * @IEEE80211_KEY_FLAG_GENERATE_IV_MGMT: This flag should be set by the
2176 * driver for a CCMP/GCMP key to indicate that is requires IV generation
2177 * only for management frames (MFP).
2178 * @IEEE80211_KEY_FLAG_RESERVE_TAILROOM: This flag should be set by the
2179 * driver for a key to indicate that sufficient tailroom must always
2180 * be reserved for ICV or MIC, even when HW encryption is enabled.
2181 * @IEEE80211_KEY_FLAG_PUT_MIC_SPACE: This flag should be set by the driver for
2182 * a TKIP key if it only requires MIC space. Do not set together with
2183 * @IEEE80211_KEY_FLAG_GENERATE_MMIC on the same key.
2184 * @IEEE80211_KEY_FLAG_NO_AUTO_TX: Key needs explicit Tx activation.
2185 * @IEEE80211_KEY_FLAG_GENERATE_MMIE: This flag should be set by the driver
2186 * for a AES_CMAC or a AES_GMAC key to indicate that it requires sequence
2187 * number generation only
2188 * @IEEE80211_KEY_FLAG_SPP_AMSDU: SPP A-MSDUs can be used with this key
2189 * (set by mac80211 from the sta->spp_amsdu flag)
2190 */
2191enum ieee80211_key_flags {
2192 IEEE80211_KEY_FLAG_GENERATE_IV_MGMT = BIT(0),
2193 IEEE80211_KEY_FLAG_GENERATE_IV = BIT(1),
2194 IEEE80211_KEY_FLAG_GENERATE_MMIC = BIT(2),
2195 IEEE80211_KEY_FLAG_PAIRWISE = BIT(3),
2196 IEEE80211_KEY_FLAG_SW_MGMT_TX = BIT(4),
2197 IEEE80211_KEY_FLAG_PUT_IV_SPACE = BIT(5),
2198 IEEE80211_KEY_FLAG_RX_MGMT = BIT(6),
2199 IEEE80211_KEY_FLAG_RESERVE_TAILROOM = BIT(7),
2200 IEEE80211_KEY_FLAG_PUT_MIC_SPACE = BIT(8),
2201 IEEE80211_KEY_FLAG_NO_AUTO_TX = BIT(9),
2202 IEEE80211_KEY_FLAG_GENERATE_MMIE = BIT(10),
2203 IEEE80211_KEY_FLAG_SPP_AMSDU = BIT(11),
2204};
2205
2206/**
2207 * struct ieee80211_key_conf - key information
2208 *
2209 * This key information is given by mac80211 to the driver by
2210 * the set_key() callback in &struct ieee80211_ops.
2211 *
2212 * @hw_key_idx: To be set by the driver, this is the key index the driver
2213 * wants to be given when a frame is transmitted and needs to be
2214 * encrypted in hardware.
2215 * @cipher: The key's cipher suite selector.
2216 * @tx_pn: PN used for TX keys, may be used by the driver as well if it
2217 * needs to do software PN assignment by itself (e.g. due to TSO)
2218 * @flags: key flags, see &enum ieee80211_key_flags.
2219 * @keyidx: the key index (0-3)
2220 * @keylen: key material length
2221 * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
2222 * data block:
2223 * - Temporal Encryption Key (128 bits)
2224 * - Temporal Authenticator Tx MIC Key (64 bits)
2225 * - Temporal Authenticator Rx MIC Key (64 bits)
2226 * @icv_len: The ICV length for this key type
2227 * @iv_len: The IV length for this key type
2228 * @link_id: the link ID for MLO, or -1 for non-MLO or pairwise keys
2229 */
2230struct ieee80211_key_conf {
2231 atomic64_t tx_pn;
2232 u32 cipher;
2233 u8 icv_len;
2234 u8 iv_len;
2235 u8 hw_key_idx;
2236 s8 keyidx;
2237 u16 flags;
2238 s8 link_id;
2239 u8 keylen;
2240 u8 key[];
2241};
2242
2243#define IEEE80211_MAX_PN_LEN 16
2244
2245#define TKIP_PN_TO_IV16(pn) ((u16)(pn & 0xffff))
2246#define TKIP_PN_TO_IV32(pn) ((u32)((pn >> 16) & 0xffffffff))
2247
2248/**
2249 * struct ieee80211_key_seq - key sequence counter
2250 *
2251 * @tkip: TKIP data, containing IV32 and IV16 in host byte order
2252 * @ccmp: PN data, most significant byte first (big endian,
2253 * reverse order than in packet)
2254 * @aes_cmac: PN data, most significant byte first (big endian,
2255 * reverse order than in packet)
2256 * @aes_gmac: PN data, most significant byte first (big endian,
2257 * reverse order than in packet)
2258 * @gcmp: PN data, most significant byte first (big endian,
2259 * reverse order than in packet)
2260 * @hw: data for HW-only (e.g. cipher scheme) keys
2261 */
2262struct ieee80211_key_seq {
2263 union {
2264 struct {
2265 u32 iv32;
2266 u16 iv16;
2267 } tkip;
2268 struct {
2269 u8 pn[6];
2270 } ccmp;
2271 struct {
2272 u8 pn[6];
2273 } aes_cmac;
2274 struct {
2275 u8 pn[6];
2276 } aes_gmac;
2277 struct {
2278 u8 pn[6];
2279 } gcmp;
2280 struct {
2281 u8 seq[IEEE80211_MAX_PN_LEN];
2282 u8 seq_len;
2283 } hw;
2284 };
2285};
2286
2287/**
2288 * enum set_key_cmd - key command
2289 *
2290 * Used with the set_key() callback in &struct ieee80211_ops, this
2291 * indicates whether a key is being removed or added.
2292 *
2293 * @SET_KEY: a key is set
2294 * @DISABLE_KEY: a key must be disabled
2295 */
2296enum set_key_cmd {
2297 SET_KEY, DISABLE_KEY,
2298};
2299
2300/**
2301 * enum ieee80211_sta_state - station state
2302 *
2303 * @IEEE80211_STA_NOTEXIST: station doesn't exist at all,
2304 * this is a special state for add/remove transitions
2305 * @IEEE80211_STA_NONE: station exists without special state
2306 * @IEEE80211_STA_AUTH: station is authenticated
2307 * @IEEE80211_STA_ASSOC: station is associated
2308 * @IEEE80211_STA_AUTHORIZED: station is authorized (802.1X)
2309 */
2310enum ieee80211_sta_state {
2311 /* NOTE: These need to be ordered correctly! */
2312 IEEE80211_STA_NOTEXIST,
2313 IEEE80211_STA_NONE,
2314 IEEE80211_STA_AUTH,
2315 IEEE80211_STA_ASSOC,
2316 IEEE80211_STA_AUTHORIZED,
2317};
2318
2319/**
2320 * enum ieee80211_sta_rx_bandwidth - station RX bandwidth
2321 * @IEEE80211_STA_RX_BW_20: station can only receive 20 MHz
2322 * @IEEE80211_STA_RX_BW_40: station can receive up to 40 MHz
2323 * @IEEE80211_STA_RX_BW_80: station can receive up to 80 MHz
2324 * @IEEE80211_STA_RX_BW_160: station can receive up to 160 MHz
2325 * (including 80+80 MHz)
2326 * @IEEE80211_STA_RX_BW_320: station can receive up to 320 MHz
2327 *
2328 * Implementation note: 20 must be zero to be initialized
2329 * correctly, the values must be sorted.
2330 */
2331enum ieee80211_sta_rx_bandwidth {
2332 IEEE80211_STA_RX_BW_20 = 0,
2333 IEEE80211_STA_RX_BW_40,
2334 IEEE80211_STA_RX_BW_80,
2335 IEEE80211_STA_RX_BW_160,
2336 IEEE80211_STA_RX_BW_320,
2337};
2338
2339/**
2340 * struct ieee80211_sta_rates - station rate selection table
2341 *
2342 * @rcu_head: RCU head used for freeing the table on update
2343 * @rate: transmit rates/flags to be used by default.
2344 * Overriding entries per-packet is possible by using cb tx control.
2345 */
2346struct ieee80211_sta_rates {
2347 struct rcu_head rcu_head;
2348 struct {
2349 s8 idx;
2350 u8 count;
2351 u8 count_cts;
2352 u8 count_rts;
2353 u16 flags;
2354 } rate[IEEE80211_TX_RATE_TABLE_SIZE];
2355};
2356
2357/**
2358 * struct ieee80211_sta_txpwr - station txpower configuration
2359 *
2360 * Used to configure txpower for station.
2361 *
2362 * @power: indicates the tx power, in dBm, to be used when sending data frames
2363 * to the STA.
2364 * @type: In particular if TPC %type is NL80211_TX_POWER_LIMITED then tx power
2365 * will be less than or equal to specified from userspace, whereas if TPC
2366 * %type is NL80211_TX_POWER_AUTOMATIC then it indicates default tx power.
2367 * NL80211_TX_POWER_FIXED is not a valid configuration option for
2368 * per peer TPC.
2369 */
2370struct ieee80211_sta_txpwr {
2371 s16 power;
2372 enum nl80211_tx_power_setting type;
2373};
2374
2375/**
2376 * struct ieee80211_sta_aggregates - info that is aggregated from active links
2377 *
2378 * Used for any per-link data that needs to be aggregated and updated in the
2379 * main &struct ieee80211_sta when updated or the active links change.
2380 *
2381 * @max_amsdu_len: indicates the maximal length of an A-MSDU in bytes.
2382 * This field is always valid for packets with a VHT preamble.
2383 * For packets with a HT preamble, additional limits apply:
2384 *
2385 * * If the skb is transmitted as part of a BA agreement, the
2386 * A-MSDU maximal size is min(max_amsdu_len, 4065) bytes.
2387 * * If the skb is not part of a BA agreement, the A-MSDU maximal
2388 * size is min(max_amsdu_len, 7935) bytes.
2389 *
2390 * Both additional HT limits must be enforced by the low level
2391 * driver. This is defined by the spec (IEEE 802.11-2012 section
2392 * 8.3.2.2 NOTE 2).
2393 * @max_rc_amsdu_len: Maximum A-MSDU size in bytes recommended by rate control.
2394 * @max_tid_amsdu_len: Maximum A-MSDU size in bytes for this TID
2395 */
2396struct ieee80211_sta_aggregates {
2397 u16 max_amsdu_len;
2398
2399 u16 max_rc_amsdu_len;
2400 u16 max_tid_amsdu_len[IEEE80211_NUM_TIDS];
2401};
2402
2403/**
2404 * struct ieee80211_link_sta - station Link specific info
2405 * All link specific info for a STA link for a non MLD STA(single)
2406 * or a MLD STA(multiple entries) are stored here.
2407 *
2408 * @sta: reference to owning STA
2409 * @addr: MAC address of the Link STA. For non-MLO STA this is same as the addr
2410 * in ieee80211_sta. For MLO Link STA this addr can be same or different
2411 * from addr in ieee80211_sta (representing MLD STA addr)
2412 * @link_id: the link ID for this link STA (0 for deflink)
2413 * @smps_mode: current SMPS mode (off, static or dynamic)
2414 * @supp_rates: Bitmap of supported rates
2415 * @ht_cap: HT capabilities of this STA; restricted to our own capabilities
2416 * @vht_cap: VHT capabilities of this STA; restricted to our own capabilities
2417 * @he_cap: HE capabilities of this STA
2418 * @he_6ghz_capa: on 6 GHz, holds the HE 6 GHz band capabilities
2419 * @eht_cap: EHT capabilities of this STA
2420 * @agg: per-link data for multi-link aggregation
2421 * @bandwidth: current bandwidth the station can receive with
2422 * @rx_nss: in HT/VHT, the maximum number of spatial streams the
2423 * station can receive at the moment, changed by operating mode
2424 * notifications and capabilities. The value is only valid after
2425 * the station moves to associated state.
2426 * @txpwr: the station tx power configuration
2427 *
2428 */
2429struct ieee80211_link_sta {
2430 struct ieee80211_sta *sta;
2431
2432 u8 addr[ETH_ALEN];
2433 u8 link_id;
2434 enum ieee80211_smps_mode smps_mode;
2435
2436 u32 supp_rates[NUM_NL80211_BANDS];
2437 struct ieee80211_sta_ht_cap ht_cap;
2438 struct ieee80211_sta_vht_cap vht_cap;
2439 struct ieee80211_sta_he_cap he_cap;
2440 struct ieee80211_he_6ghz_capa he_6ghz_capa;
2441 struct ieee80211_sta_eht_cap eht_cap;
2442
2443 struct ieee80211_sta_aggregates agg;
2444
2445 u8 rx_nss;
2446 enum ieee80211_sta_rx_bandwidth bandwidth;
2447 struct ieee80211_sta_txpwr txpwr;
2448};
2449
2450/**
2451 * struct ieee80211_sta - station table entry
2452 *
2453 * A station table entry represents a station we are possibly
2454 * communicating with. Since stations are RCU-managed in
2455 * mac80211, any ieee80211_sta pointer you get access to must
2456 * either be protected by rcu_read_lock() explicitly or implicitly,
2457 * or you must take good care to not use such a pointer after a
2458 * call to your sta_remove callback that removed it.
2459 * This also represents the MLD STA in case of MLO association
2460 * and holds pointers to various link STA's
2461 *
2462 * @addr: MAC address
2463 * @aid: AID we assigned to the station if we're an AP
2464 * @max_rx_aggregation_subframes: maximal amount of frames in a single AMPDU
2465 * that this station is allowed to transmit to us.
2466 * Can be modified by driver.
2467 * @wme: indicates whether the STA supports QoS/WME (if local devices does,
2468 * otherwise always false)
2469 * @drv_priv: data area for driver use, will always be aligned to
2470 * sizeof(void \*), size is determined in hw information.
2471 * @uapsd_queues: bitmap of queues configured for uapsd. Only valid
2472 * if wme is supported. The bits order is like in
2473 * IEEE80211_WMM_IE_STA_QOSINFO_AC_*.
2474 * @max_sp: max Service Period. Only valid if wme is supported.
2475 * @rates: rate control selection table
2476 * @tdls: indicates whether the STA is a TDLS peer
2477 * @tdls_initiator: indicates the STA is an initiator of the TDLS link. Only
2478 * valid if the STA is a TDLS peer in the first place.
2479 * @mfp: indicates whether the STA uses management frame protection or not.
2480 * @mlo: indicates whether the STA is MLO station.
2481 * @max_amsdu_subframes: indicates the maximal number of MSDUs in a single
2482 * A-MSDU. Taken from the Extended Capabilities element. 0 means
2483 * unlimited.
2484 * @cur: currently valid data as aggregated from the active links
2485 * For non MLO STA it will point to the deflink data. For MLO STA
2486 * ieee80211_sta_recalc_aggregates() must be called to update it.
2487 * @support_p2p_ps: indicates whether the STA supports P2P PS mechanism or not.
2488 * @txq: per-TID data TX queues; note that the last entry (%IEEE80211_NUM_TIDS)
2489 * is used for non-data frames
2490 * @deflink: This holds the default link STA information, for non MLO STA all link
2491 * specific STA information is accessed through @deflink or through
2492 * link[0] which points to address of @deflink. For MLO Link STA
2493 * the first added link STA will point to deflink.
2494 * @link: reference to Link Sta entries. For Non MLO STA, except 1st link,
2495 * i.e link[0] all links would be assigned to NULL by default and
2496 * would access link information via @deflink or link[0]. For MLO
2497 * STA, first link STA being added will point its link pointer to
2498 * @deflink address and remaining would be allocated and the address
2499 * would be assigned to link[link_id] where link_id is the id assigned
2500 * by the AP.
2501 * @valid_links: bitmap of valid links, or 0 for non-MLO
2502 * @spp_amsdu: indicates whether the STA uses SPP A-MSDU or not.
2503 */
2504struct ieee80211_sta {
2505 u8 addr[ETH_ALEN] __aligned(2);
2506 u16 aid;
2507 u16 max_rx_aggregation_subframes;
2508 bool wme;
2509 u8 uapsd_queues;
2510 u8 max_sp;
2511 struct ieee80211_sta_rates __rcu *rates;
2512 bool tdls;
2513 bool tdls_initiator;
2514 bool mfp;
2515 bool mlo;
2516 bool spp_amsdu;
2517 u8 max_amsdu_subframes;
2518
2519 struct ieee80211_sta_aggregates *cur;
2520
2521 bool support_p2p_ps;
2522
2523 struct ieee80211_txq *txq[IEEE80211_NUM_TIDS + 1];
2524
2525 u16 valid_links;
2526 struct ieee80211_link_sta deflink;
2527 struct ieee80211_link_sta __rcu *link[IEEE80211_MLD_MAX_NUM_LINKS];
2528
2529 /* must be last */
2530 u8 drv_priv[] __aligned(sizeof(void *));
2531};
2532
2533#ifdef CONFIG_LOCKDEP
2534bool lockdep_sta_mutex_held(struct ieee80211_sta *pubsta);
2535#else
2536static inline bool lockdep_sta_mutex_held(struct ieee80211_sta *pubsta)
2537{
2538 return true;
2539}
2540#endif
2541
2542#define link_sta_dereference_protected(sta, link_id) \
2543 rcu_dereference_protected((sta)->link[link_id], \
2544 lockdep_sta_mutex_held(sta))
2545
2546#define link_sta_dereference_check(sta, link_id) \
2547 rcu_dereference_check((sta)->link[link_id], \
2548 lockdep_sta_mutex_held(sta))
2549
2550#define for_each_sta_active_link(vif, sta, link_sta, link_id) \
2551 for (link_id = 0; link_id < ARRAY_SIZE((sta)->link); link_id++) \
2552 if ((!(vif)->active_links || \
2553 (vif)->active_links & BIT(link_id)) && \
2554 ((link_sta) = link_sta_dereference_check(sta, link_id)))
2555
2556/**
2557 * enum sta_notify_cmd - sta notify command
2558 *
2559 * Used with the sta_notify() callback in &struct ieee80211_ops, this
2560 * indicates if an associated station made a power state transition.
2561 *
2562 * @STA_NOTIFY_SLEEP: a station is now sleeping
2563 * @STA_NOTIFY_AWAKE: a sleeping station woke up
2564 */
2565enum sta_notify_cmd {
2566 STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
2567};
2568
2569/**
2570 * struct ieee80211_tx_control - TX control data
2571 *
2572 * @sta: station table entry, this sta pointer may be NULL and
2573 * it is not allowed to copy the pointer, due to RCU.
2574 */
2575struct ieee80211_tx_control {
2576 struct ieee80211_sta *sta;
2577};
2578
2579/**
2580 * struct ieee80211_txq - Software intermediate tx queue
2581 *
2582 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2583 * @sta: station table entry, %NULL for per-vif queue
2584 * @tid: the TID for this queue (unused for per-vif queue),
2585 * %IEEE80211_NUM_TIDS for non-data (if enabled)
2586 * @ac: the AC for this queue
2587 * @drv_priv: driver private area, sized by hw->txq_data_size
2588 *
2589 * The driver can obtain packets from this queue by calling
2590 * ieee80211_tx_dequeue().
2591 */
2592struct ieee80211_txq {
2593 struct ieee80211_vif *vif;
2594 struct ieee80211_sta *sta;
2595 u8 tid;
2596 u8 ac;
2597
2598 /* must be last */
2599 u8 drv_priv[] __aligned(sizeof(void *));
2600};
2601
2602/**
2603 * enum ieee80211_hw_flags - hardware flags
2604 *
2605 * These flags are used to indicate hardware capabilities to
2606 * the stack. Generally, flags here should have their meaning
2607 * done in a way that the simplest hardware doesn't need setting
2608 * any particular flags. There are some exceptions to this rule,
2609 * however, so you are advised to review these flags carefully.
2610 *
2611 * @IEEE80211_HW_HAS_RATE_CONTROL:
2612 * The hardware or firmware includes rate control, and cannot be
2613 * controlled by the stack. As such, no rate control algorithm
2614 * should be instantiated, and the TX rate reported to userspace
2615 * will be taken from the TX status instead of the rate control
2616 * algorithm.
2617 * Note that this requires that the driver implement a number of
2618 * callbacks so it has the correct information, it needs to have
2619 * the @set_rts_threshold callback and must look at the BSS config
2620 * @use_cts_prot for G/N protection, @use_short_slot for slot
2621 * timing in 2.4 GHz and @use_short_preamble for preambles for
2622 * CCK frames.
2623 *
2624 * @IEEE80211_HW_RX_INCLUDES_FCS:
2625 * Indicates that received frames passed to the stack include
2626 * the FCS at the end.
2627 *
2628 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
2629 * Some wireless LAN chipsets buffer broadcast/multicast frames
2630 * for power saving stations in the hardware/firmware and others
2631 * rely on the host system for such buffering. This option is used
2632 * to configure the IEEE 802.11 upper layer to buffer broadcast and
2633 * multicast frames when there are power saving stations so that
2634 * the driver can fetch them with ieee80211_get_buffered_bc().
2635 *
2636 * @IEEE80211_HW_SIGNAL_UNSPEC:
2637 * Hardware can provide signal values but we don't know its units. We
2638 * expect values between 0 and @max_signal.
2639 * If possible please provide dB or dBm instead.
2640 *
2641 * @IEEE80211_HW_SIGNAL_DBM:
2642 * Hardware gives signal values in dBm, decibel difference from
2643 * one milliwatt. This is the preferred method since it is standardized
2644 * between different devices. @max_signal does not need to be set.
2645 *
2646 * @IEEE80211_HW_SPECTRUM_MGMT:
2647 * Hardware supports spectrum management defined in 802.11h
2648 * Measurement, Channel Switch, Quieting, TPC
2649 *
2650 * @IEEE80211_HW_AMPDU_AGGREGATION:
2651 * Hardware supports 11n A-MPDU aggregation.
2652 *
2653 * @IEEE80211_HW_SUPPORTS_PS:
2654 * Hardware has power save support (i.e. can go to sleep).
2655 *
2656 * @IEEE80211_HW_PS_NULLFUNC_STACK:
2657 * Hardware requires nullfunc frame handling in stack, implies
2658 * stack support for dynamic PS.
2659 *
2660 * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
2661 * Hardware has support for dynamic PS.
2662 *
2663 * @IEEE80211_HW_MFP_CAPABLE:
2664 * Hardware supports management frame protection (MFP, IEEE 802.11w).
2665 *
2666 * @IEEE80211_HW_REPORTS_TX_ACK_STATUS:
2667 * Hardware can provide ack status reports of Tx frames to
2668 * the stack.
2669 *
2670 * @IEEE80211_HW_CONNECTION_MONITOR:
2671 * The hardware performs its own connection monitoring, including
2672 * periodic keep-alives to the AP and probing the AP on beacon loss.
2673 *
2674 * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC:
2675 * This device needs to get data from beacon before association (i.e.
2676 * dtim_period).
2677 *
2678 * @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports
2679 * per-station GTKs as used by IBSS RSN or during fast transition. If
2680 * the device doesn't support per-station GTKs, but can be asked not
2681 * to decrypt group addressed frames, then IBSS RSN support is still
2682 * possible but software crypto will be used. Advertise the wiphy flag
2683 * only in that case.
2684 *
2685 * @IEEE80211_HW_AP_LINK_PS: When operating in AP mode the device
2686 * autonomously manages the PS status of connected stations. When
2687 * this flag is set mac80211 will not trigger PS mode for connected
2688 * stations based on the PM bit of incoming frames.
2689 * Use ieee80211_start_ps()/ieee8021_end_ps() to manually configure
2690 * the PS mode of connected stations.
2691 *
2692 * @IEEE80211_HW_TX_AMPDU_SETUP_IN_HW: The device handles TX A-MPDU session
2693 * setup strictly in HW. mac80211 should not attempt to do this in
2694 * software.
2695 *
2696 * @IEEE80211_HW_WANT_MONITOR_VIF: The driver would like to be informed of
2697 * a virtual monitor interface when monitor interfaces are the only
2698 * active interfaces.
2699 *
2700 * @IEEE80211_HW_NO_VIRTUAL_MONITOR: The driver would like to be informed
2701 * of any monitor interface, as well as their configured channel.
2702 * This is useful for supporting multiple monitor interfaces on different
2703 * channels.
2704 *
2705 * @IEEE80211_HW_NO_AUTO_VIF: The driver would like for no wlanX to
2706 * be created. It is expected user-space will create vifs as
2707 * desired (and thus have them named as desired).
2708 *
2709 * @IEEE80211_HW_SW_CRYPTO_CONTROL: The driver wants to control which of the
2710 * crypto algorithms can be done in software - so don't automatically
2711 * try to fall back to it if hardware crypto fails, but do so only if
2712 * the driver returns 1. This also forces the driver to advertise its
2713 * supported cipher suites.
2714 *
2715 * @IEEE80211_HW_SUPPORT_FAST_XMIT: The driver/hardware supports fast-xmit,
2716 * this currently requires only the ability to calculate the duration
2717 * for frames.
2718 *
2719 * @IEEE80211_HW_QUEUE_CONTROL: The driver wants to control per-interface
2720 * queue mapping in order to use different queues (not just one per AC)
2721 * for different virtual interfaces. See the doc section on HW queue
2722 * control for more details.
2723 *
2724 * @IEEE80211_HW_SUPPORTS_RC_TABLE: The driver supports using a rate
2725 * selection table provided by the rate control algorithm.
2726 *
2727 * @IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF: Use the P2P Device address for any
2728 * P2P Interface. This will be honoured even if more than one interface
2729 * is supported.
2730 *
2731 * @IEEE80211_HW_TIMING_BEACON_ONLY: Use sync timing from beacon frames
2732 * only, to allow getting TBTT of a DTIM beacon.
2733 *
2734 * @IEEE80211_HW_SUPPORTS_HT_CCK_RATES: Hardware supports mixing HT/CCK rates
2735 * and can cope with CCK rates in an aggregation session (e.g. by not
2736 * using aggregation for such frames.)
2737 *
2738 * @IEEE80211_HW_CHANCTX_STA_CSA: Support 802.11h based channel-switch (CSA)
2739 * for a single active channel while using channel contexts. When support
2740 * is not enabled the default action is to disconnect when getting the
2741 * CSA frame.
2742 *
2743 * @IEEE80211_HW_SUPPORTS_CLONED_SKBS: The driver will never modify the payload
2744 * or tailroom of TX skbs without copying them first.
2745 *
2746 * @IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS: The HW supports scanning on all bands
2747 * in one command, mac80211 doesn't have to run separate scans per band.
2748 *
2749 * @IEEE80211_HW_TDLS_WIDER_BW: The device/driver supports wider bandwidth
2750 * than then BSS bandwidth for a TDLS link on the base channel.
2751 *
2752 * @IEEE80211_HW_SUPPORTS_AMSDU_IN_AMPDU: The driver supports receiving A-MSDUs
2753 * within A-MPDU.
2754 *
2755 * @IEEE80211_HW_BEACON_TX_STATUS: The device/driver provides TX status
2756 * for sent beacons.
2757 *
2758 * @IEEE80211_HW_NEEDS_UNIQUE_STA_ADDR: Hardware (or driver) requires that each
2759 * station has a unique address, i.e. each station entry can be identified
2760 * by just its MAC address; this prevents, for example, the same station
2761 * from connecting to two virtual AP interfaces at the same time.
2762 *
2763 * @IEEE80211_HW_SUPPORTS_REORDERING_BUFFER: Hardware (or driver) manages the
2764 * reordering buffer internally, guaranteeing mac80211 receives frames in
2765 * order and does not need to manage its own reorder buffer or BA session
2766 * timeout.
2767 *
2768 * @IEEE80211_HW_USES_RSS: The device uses RSS and thus requires parallel RX,
2769 * which implies using per-CPU station statistics.
2770 *
2771 * @IEEE80211_HW_TX_AMSDU: Hardware (or driver) supports software aggregated
2772 * A-MSDU frames. Requires software tx queueing and fast-xmit support.
2773 * When not using minstrel/minstrel_ht rate control, the driver must
2774 * limit the maximum A-MSDU size based on the current tx rate by setting
2775 * max_rc_amsdu_len in struct ieee80211_sta.
2776 *
2777 * @IEEE80211_HW_TX_FRAG_LIST: Hardware (or driver) supports sending frag_list
2778 * skbs, needed for zero-copy software A-MSDU.
2779 *
2780 * @IEEE80211_HW_REPORTS_LOW_ACK: The driver (or firmware) reports low ack event
2781 * by ieee80211_report_low_ack() based on its own algorithm. For such
2782 * drivers, mac80211 packet loss mechanism will not be triggered and driver
2783 * is completely depending on firmware event for station kickout.
2784 *
2785 * @IEEE80211_HW_SUPPORTS_TX_FRAG: Hardware does fragmentation by itself.
2786 * The stack will not do fragmentation.
2787 * The callback for @set_frag_threshold should be set as well.
2788 *
2789 * @IEEE80211_HW_SUPPORTS_TDLS_BUFFER_STA: Hardware supports buffer STA on
2790 * TDLS links.
2791 *
2792 * @IEEE80211_HW_DOESNT_SUPPORT_QOS_NDP: The driver (or firmware) doesn't
2793 * support QoS NDP for AP probing - that's most likely a driver bug.
2794 *
2795 * @IEEE80211_HW_BUFF_MMPDU_TXQ: use the TXQ for bufferable MMPDUs, this of
2796 * course requires the driver to use TXQs to start with.
2797 *
2798 * @IEEE80211_HW_SUPPORTS_VHT_EXT_NSS_BW: (Hardware) rate control supports VHT
2799 * extended NSS BW (dot11VHTExtendedNSSBWCapable). This flag will be set if
2800 * the selected rate control algorithm sets %RATE_CTRL_CAPA_VHT_EXT_NSS_BW
2801 * but if the rate control is built-in then it must be set by the driver.
2802 * See also the documentation for that flag.
2803 *
2804 * @IEEE80211_HW_STA_MMPDU_TXQ: use the extra non-TID per-station TXQ for all
2805 * MMPDUs on station interfaces. This of course requires the driver to use
2806 * TXQs to start with.
2807 *
2808 * @IEEE80211_HW_TX_STATUS_NO_AMPDU_LEN: Driver does not report accurate A-MPDU
2809 * length in tx status information
2810 *
2811 * @IEEE80211_HW_SUPPORTS_MULTI_BSSID: Hardware supports multi BSSID
2812 *
2813 * @IEEE80211_HW_SUPPORTS_ONLY_HE_MULTI_BSSID: Hardware supports multi BSSID
2814 * only for HE APs. Applies if @IEEE80211_HW_SUPPORTS_MULTI_BSSID is set.
2815 *
2816 * @IEEE80211_HW_AMPDU_KEYBORDER_SUPPORT: The card and driver is only
2817 * aggregating MPDUs with the same keyid, allowing mac80211 to keep Tx
2818 * A-MPDU sessions active while rekeying with Extended Key ID.
2819 *
2820 * @IEEE80211_HW_SUPPORTS_TX_ENCAP_OFFLOAD: Hardware supports tx encapsulation
2821 * offload
2822 *
2823 * @IEEE80211_HW_SUPPORTS_RX_DECAP_OFFLOAD: Hardware supports rx decapsulation
2824 * offload
2825 *
2826 * @IEEE80211_HW_SUPPORTS_CONC_MON_RX_DECAP: Hardware supports concurrent rx
2827 * decapsulation offload and passing raw 802.11 frames for monitor iface.
2828 * If this is supported, the driver must pass both 802.3 frames for real
2829 * usage and 802.11 frames with %RX_FLAG_ONLY_MONITOR set for monitor to
2830 * the stack.
2831 *
2832 * @IEEE80211_HW_DETECTS_COLOR_COLLISION: HW/driver has support for BSS color
2833 * collision detection and doesn't need it in software.
2834 *
2835 * @IEEE80211_HW_MLO_MCAST_MULTI_LINK_TX: Hardware/driver handles transmitting
2836 * multicast frames on all links, mac80211 should not do that.
2837 *
2838 * @IEEE80211_HW_DISALLOW_PUNCTURING: HW requires disabling puncturing in EHT
2839 * and connecting with a lower bandwidth instead
2840 * @IEEE80211_HW_DISALLOW_PUNCTURING_5GHZ: HW requires disabling puncturing in
2841 * EHT in 5 GHz and connecting with a lower bandwidth instead
2842 *
2843 * @IEEE80211_HW_HANDLES_QUIET_CSA: HW/driver handles quieting for CSA, so
2844 * no need to stop queues. This really should be set by a driver that
2845 * implements MLO, so operation can continue on other links when one
2846 * link is switching.
2847 *
2848 * @NUM_IEEE80211_HW_FLAGS: number of hardware flags, used for sizing arrays
2849 */
2850enum ieee80211_hw_flags {
2851 IEEE80211_HW_HAS_RATE_CONTROL,
2852 IEEE80211_HW_RX_INCLUDES_FCS,
2853 IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING,
2854 IEEE80211_HW_SIGNAL_UNSPEC,
2855 IEEE80211_HW_SIGNAL_DBM,
2856 IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC,
2857 IEEE80211_HW_SPECTRUM_MGMT,
2858 IEEE80211_HW_AMPDU_AGGREGATION,
2859 IEEE80211_HW_SUPPORTS_PS,
2860 IEEE80211_HW_PS_NULLFUNC_STACK,
2861 IEEE80211_HW_SUPPORTS_DYNAMIC_PS,
2862 IEEE80211_HW_MFP_CAPABLE,
2863 IEEE80211_HW_WANT_MONITOR_VIF,
2864 IEEE80211_HW_NO_VIRTUAL_MONITOR,
2865 IEEE80211_HW_NO_AUTO_VIF,
2866 IEEE80211_HW_SW_CRYPTO_CONTROL,
2867 IEEE80211_HW_SUPPORT_FAST_XMIT,
2868 IEEE80211_HW_REPORTS_TX_ACK_STATUS,
2869 IEEE80211_HW_CONNECTION_MONITOR,
2870 IEEE80211_HW_QUEUE_CONTROL,
2871 IEEE80211_HW_SUPPORTS_PER_STA_GTK,
2872 IEEE80211_HW_AP_LINK_PS,
2873 IEEE80211_HW_TX_AMPDU_SETUP_IN_HW,
2874 IEEE80211_HW_SUPPORTS_RC_TABLE,
2875 IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF,
2876 IEEE80211_HW_TIMING_BEACON_ONLY,
2877 IEEE80211_HW_SUPPORTS_HT_CCK_RATES,
2878 IEEE80211_HW_CHANCTX_STA_CSA,
2879 IEEE80211_HW_SUPPORTS_CLONED_SKBS,
2880 IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS,
2881 IEEE80211_HW_TDLS_WIDER_BW,
2882 IEEE80211_HW_SUPPORTS_AMSDU_IN_AMPDU,
2883 IEEE80211_HW_BEACON_TX_STATUS,
2884 IEEE80211_HW_NEEDS_UNIQUE_STA_ADDR,
2885 IEEE80211_HW_SUPPORTS_REORDERING_BUFFER,
2886 IEEE80211_HW_USES_RSS,
2887 IEEE80211_HW_TX_AMSDU,
2888 IEEE80211_HW_TX_FRAG_LIST,
2889 IEEE80211_HW_REPORTS_LOW_ACK,
2890 IEEE80211_HW_SUPPORTS_TX_FRAG,
2891 IEEE80211_HW_SUPPORTS_TDLS_BUFFER_STA,
2892 IEEE80211_HW_DOESNT_SUPPORT_QOS_NDP,
2893 IEEE80211_HW_BUFF_MMPDU_TXQ,
2894 IEEE80211_HW_SUPPORTS_VHT_EXT_NSS_BW,
2895 IEEE80211_HW_STA_MMPDU_TXQ,
2896 IEEE80211_HW_TX_STATUS_NO_AMPDU_LEN,
2897 IEEE80211_HW_SUPPORTS_MULTI_BSSID,
2898 IEEE80211_HW_SUPPORTS_ONLY_HE_MULTI_BSSID,
2899 IEEE80211_HW_AMPDU_KEYBORDER_SUPPORT,
2900 IEEE80211_HW_SUPPORTS_TX_ENCAP_OFFLOAD,
2901 IEEE80211_HW_SUPPORTS_RX_DECAP_OFFLOAD,
2902 IEEE80211_HW_SUPPORTS_CONC_MON_RX_DECAP,
2903 IEEE80211_HW_DETECTS_COLOR_COLLISION,
2904 IEEE80211_HW_MLO_MCAST_MULTI_LINK_TX,
2905 IEEE80211_HW_DISALLOW_PUNCTURING,
2906 IEEE80211_HW_DISALLOW_PUNCTURING_5GHZ,
2907 IEEE80211_HW_HANDLES_QUIET_CSA,
2908
2909 /* keep last, obviously */
2910 NUM_IEEE80211_HW_FLAGS
2911};
2912
2913/**
2914 * struct ieee80211_hw - hardware information and state
2915 *
2916 * This structure contains the configuration and hardware
2917 * information for an 802.11 PHY.
2918 *
2919 * @wiphy: This points to the &struct wiphy allocated for this
2920 * 802.11 PHY. You must fill in the @perm_addr and @dev
2921 * members of this structure using SET_IEEE80211_DEV()
2922 * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
2923 * bands (with channels, bitrates) are registered here.
2924 *
2925 * @conf: &struct ieee80211_conf, device configuration, don't use.
2926 *
2927 * @priv: pointer to private area that was allocated for driver use
2928 * along with this structure.
2929 *
2930 * @flags: hardware flags, see &enum ieee80211_hw_flags.
2931 *
2932 * @extra_tx_headroom: headroom to reserve in each transmit skb
2933 * for use by the driver (e.g. for transmit headers.)
2934 *
2935 * @extra_beacon_tailroom: tailroom to reserve in each beacon tx skb.
2936 * Can be used by drivers to add extra IEs.
2937 *
2938 * @max_signal: Maximum value for signal (rssi) in RX information, used
2939 * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
2940 *
2941 * @max_listen_interval: max listen interval in units of beacon interval
2942 * that HW supports
2943 *
2944 * @queues: number of available hardware transmit queues for
2945 * data packets. WMM/QoS requires at least four, these
2946 * queues need to have configurable access parameters.
2947 *
2948 * @rate_control_algorithm: rate control algorithm for this hardware.
2949 * If unset (NULL), the default algorithm will be used. Must be
2950 * set before calling ieee80211_register_hw().
2951 *
2952 * @vif_data_size: size (in bytes) of the drv_priv data area
2953 * within &struct ieee80211_vif.
2954 * @sta_data_size: size (in bytes) of the drv_priv data area
2955 * within &struct ieee80211_sta.
2956 * @chanctx_data_size: size (in bytes) of the drv_priv data area
2957 * within &struct ieee80211_chanctx_conf.
2958 * @txq_data_size: size (in bytes) of the drv_priv data area
2959 * within @struct ieee80211_txq.
2960 *
2961 * @max_rates: maximum number of alternate rate retry stages the hw
2962 * can handle.
2963 * @max_report_rates: maximum number of alternate rate retry stages
2964 * the hw can report back.
2965 * @max_rate_tries: maximum number of tries for each stage
2966 *
2967 * @max_rx_aggregation_subframes: maximum buffer size (number of
2968 * sub-frames) to be used for A-MPDU block ack receiver
2969 * aggregation.
2970 * This is only relevant if the device has restrictions on the
2971 * number of subframes, if it relies on mac80211 to do reordering
2972 * it shouldn't be set.
2973 *
2974 * @max_tx_aggregation_subframes: maximum number of subframes in an
2975 * aggregate an HT/HE device will transmit. In HT AddBA we'll
2976 * advertise a constant value of 64 as some older APs crash if
2977 * the window size is smaller (an example is LinkSys WRT120N
2978 * with FW v1.0.07 build 002 Jun 18 2012).
2979 * For AddBA to HE capable peers this value will be used.
2980 *
2981 * @max_tx_fragments: maximum number of tx buffers per (A)-MSDU, sum
2982 * of 1 + skb_shinfo(skb)->nr_frags for each skb in the frag_list.
2983 *
2984 * @offchannel_tx_hw_queue: HW queue ID to use for offchannel TX
2985 * (if %IEEE80211_HW_QUEUE_CONTROL is set)
2986 *
2987 * @radiotap_mcs_details: lists which MCS information can the HW
2988 * reports, by default it is set to _MCS, _GI and _BW but doesn't
2989 * include _FMT. Use %IEEE80211_RADIOTAP_MCS_HAVE_\* values, only
2990 * adding _BW is supported today.
2991 *
2992 * @radiotap_vht_details: lists which VHT MCS information the HW reports,
2993 * the default is _GI | _BANDWIDTH.
2994 * Use the %IEEE80211_RADIOTAP_VHT_KNOWN_\* values.
2995 *
2996 * @radiotap_timestamp: Information for the radiotap timestamp field; if the
2997 * @units_pos member is set to a non-negative value then the timestamp
2998 * field will be added and populated from the &struct ieee80211_rx_status
2999 * device_timestamp.
3000 * @radiotap_timestamp.units_pos: Must be set to a combination of a
3001 * IEEE80211_RADIOTAP_TIMESTAMP_UNIT_* and a
3002 * IEEE80211_RADIOTAP_TIMESTAMP_SPOS_* value.
3003 * @radiotap_timestamp.accuracy: If non-negative, fills the accuracy in the
3004 * radiotap field and the accuracy known flag will be set.
3005 *
3006 * @netdev_features: netdev features to be set in each netdev created
3007 * from this HW. Note that not all features are usable with mac80211,
3008 * other features will be rejected during HW registration.
3009 *
3010 * @uapsd_queues: This bitmap is included in (re)association frame to indicate
3011 * for each access category if it is uAPSD trigger-enabled and delivery-
3012 * enabled. Use IEEE80211_WMM_IE_STA_QOSINFO_AC_* to set this bitmap.
3013 * Each bit corresponds to different AC. Value '1' in specific bit means
3014 * that corresponding AC is both trigger- and delivery-enabled. '0' means
3015 * neither enabled.
3016 *
3017 * @uapsd_max_sp_len: maximum number of total buffered frames the WMM AP may
3018 * deliver to a WMM STA during any Service Period triggered by the WMM STA.
3019 * Use IEEE80211_WMM_IE_STA_QOSINFO_SP_* for correct values.
3020 *
3021 * @max_nan_de_entries: maximum number of NAN DE functions supported by the
3022 * device.
3023 *
3024 * @tx_sk_pacing_shift: Pacing shift to set on TCP sockets when frames from
3025 * them are encountered. The default should typically not be changed,
3026 * unless the driver has good reasons for needing more buffers.
3027 *
3028 * @weight_multiplier: Driver specific airtime weight multiplier used while
3029 * refilling deficit of each TXQ.
3030 *
3031 * @max_mtu: the max mtu could be set.
3032 *
3033 * @tx_power_levels: a list of power levels supported by the wifi hardware.
3034 * The power levels can be specified either as integer or fractions.
3035 * The power level at idx 0 shall be the maximum positive power level.
3036 *
3037 * @max_txpwr_levels_idx: the maximum valid idx of 'tx_power_levels' list.
3038 */
3039struct ieee80211_hw {
3040 struct ieee80211_conf conf;
3041 struct wiphy *wiphy;
3042 const char *rate_control_algorithm;
3043 void *priv;
3044 unsigned long flags[BITS_TO_LONGS(NUM_IEEE80211_HW_FLAGS)];
3045 unsigned int extra_tx_headroom;
3046 unsigned int extra_beacon_tailroom;
3047 int vif_data_size;
3048 int sta_data_size;
3049 int chanctx_data_size;
3050 int txq_data_size;
3051 u16 queues;
3052 u16 max_listen_interval;
3053 s8 max_signal;
3054 u8 max_rates;
3055 u8 max_report_rates;
3056 u8 max_rate_tries;
3057 u16 max_rx_aggregation_subframes;
3058 u16 max_tx_aggregation_subframes;
3059 u8 max_tx_fragments;
3060 u8 offchannel_tx_hw_queue;
3061 u8 radiotap_mcs_details;
3062 u16 radiotap_vht_details;
3063 struct {
3064 int units_pos;
3065 s16 accuracy;
3066 } radiotap_timestamp;
3067 netdev_features_t netdev_features;
3068 u8 uapsd_queues;
3069 u8 uapsd_max_sp_len;
3070 u8 max_nan_de_entries;
3071 u8 tx_sk_pacing_shift;
3072 u8 weight_multiplier;
3073 u32 max_mtu;
3074 const s8 *tx_power_levels;
3075 u8 max_txpwr_levels_idx;
3076};
3077
3078static inline bool _ieee80211_hw_check(struct ieee80211_hw *hw,
3079 enum ieee80211_hw_flags flg)
3080{
3081 return test_bit(flg, hw->flags);
3082}
3083#define ieee80211_hw_check(hw, flg) _ieee80211_hw_check(hw, IEEE80211_HW_##flg)
3084
3085static inline void _ieee80211_hw_set(struct ieee80211_hw *hw,
3086 enum ieee80211_hw_flags flg)
3087{
3088 return __set_bit(flg, hw->flags);
3089}
3090#define ieee80211_hw_set(hw, flg) _ieee80211_hw_set(hw, IEEE80211_HW_##flg)
3091
3092/**
3093 * struct ieee80211_scan_request - hw scan request
3094 *
3095 * @ies: pointers different parts of IEs (in req.ie)
3096 * @req: cfg80211 request.
3097 */
3098struct ieee80211_scan_request {
3099 struct ieee80211_scan_ies ies;
3100
3101 /* Keep last */
3102 struct cfg80211_scan_request req;
3103};
3104
3105/**
3106 * struct ieee80211_tdls_ch_sw_params - TDLS channel switch parameters
3107 *
3108 * @sta: peer this TDLS channel-switch request/response came from
3109 * @chandef: channel referenced in a TDLS channel-switch request
3110 * @action_code: see &enum ieee80211_tdls_actioncode
3111 * @status: channel-switch response status
3112 * @timestamp: time at which the frame was received
3113 * @switch_time: switch-timing parameter received in the frame
3114 * @switch_timeout: switch-timing parameter received in the frame
3115 * @tmpl_skb: TDLS switch-channel response template
3116 * @ch_sw_tm_ie: offset of the channel-switch timing IE inside @tmpl_skb
3117 */
3118struct ieee80211_tdls_ch_sw_params {
3119 struct ieee80211_sta *sta;
3120 struct cfg80211_chan_def *chandef;
3121 u8 action_code;
3122 u32 status;
3123 u32 timestamp;
3124 u16 switch_time;
3125 u16 switch_timeout;
3126 struct sk_buff *tmpl_skb;
3127 u32 ch_sw_tm_ie;
3128};
3129
3130/**
3131 * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy
3132 *
3133 * @wiphy: the &struct wiphy which we want to query
3134 *
3135 * mac80211 drivers can use this to get to their respective
3136 * &struct ieee80211_hw. Drivers wishing to get to their own private
3137 * structure can then access it via hw->priv. Note that mac802111 drivers should
3138 * not use wiphy_priv() to try to get their private driver structure as this
3139 * is already used internally by mac80211.
3140 *
3141 * Return: The mac80211 driver hw struct of @wiphy.
3142 */
3143struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy);
3144
3145/**
3146 * SET_IEEE80211_DEV - set device for 802.11 hardware
3147 *
3148 * @hw: the &struct ieee80211_hw to set the device for
3149 * @dev: the &struct device of this 802.11 device
3150 */
3151static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev)
3152{
3153 set_wiphy_dev(hw->wiphy, dev);
3154}
3155
3156/**
3157 * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware
3158 *
3159 * @hw: the &struct ieee80211_hw to set the MAC address for
3160 * @addr: the address to set
3161 */
3162static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, const u8 *addr)
3163{
3164 memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
3165}
3166
3167static inline struct ieee80211_rate *
3168ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
3169 const struct ieee80211_tx_info *c)
3170{
3171 if (WARN_ON_ONCE(c->control.rates[0].idx < 0))
3172 return NULL;
3173 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx];
3174}
3175
3176static inline struct ieee80211_rate *
3177ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw,
3178 const struct ieee80211_tx_info *c)
3179{
3180 if (c->control.rts_cts_rate_idx < 0)
3181 return NULL;
3182 return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx];
3183}
3184
3185static inline struct ieee80211_rate *
3186ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
3187 const struct ieee80211_tx_info *c, int idx)
3188{
3189 if (c->control.rates[idx + 1].idx < 0)
3190 return NULL;
3191 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx];
3192}
3193
3194/**
3195 * ieee80211_free_txskb - free TX skb
3196 * @hw: the hardware
3197 * @skb: the skb
3198 *
3199 * Free a transmit skb. Use this function when some failure
3200 * to transmit happened and thus status cannot be reported.
3201 */
3202void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb);
3203
3204/**
3205 * ieee80211_purge_tx_queue - purge TX skb queue
3206 * @hw: the hardware
3207 * @skbs: the skbs
3208 *
3209 * Free a set of transmit skbs. Use this function when device is going to stop
3210 * but some transmit skbs without TX status are still queued.
3211 * This function does not take the list lock and the caller must hold the
3212 * relevant locks to use it.
3213 */
3214void ieee80211_purge_tx_queue(struct ieee80211_hw *hw,
3215 struct sk_buff_head *skbs);
3216
3217/**
3218 * DOC: Hardware crypto acceleration
3219 *
3220 * mac80211 is capable of taking advantage of many hardware
3221 * acceleration designs for encryption and decryption operations.
3222 *
3223 * The set_key() callback in the &struct ieee80211_ops for a given
3224 * device is called to enable hardware acceleration of encryption and
3225 * decryption. The callback takes a @sta parameter that will be NULL
3226 * for default keys or keys used for transmission only, or point to
3227 * the station information for the peer for individual keys.
3228 * Multiple transmission keys with the same key index may be used when
3229 * VLANs are configured for an access point.
3230 *
3231 * When transmitting, the TX control data will use the @hw_key_idx
3232 * selected by the driver by modifying the &struct ieee80211_key_conf
3233 * pointed to by the @key parameter to the set_key() function.
3234 *
3235 * The set_key() call for the %SET_KEY command should return 0 if
3236 * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be
3237 * added; if you return 0 then hw_key_idx must be assigned to the
3238 * hardware key index. You are free to use the full u8 range.
3239 *
3240 * Note that in the case that the @IEEE80211_HW_SW_CRYPTO_CONTROL flag is
3241 * set, mac80211 will not automatically fall back to software crypto if
3242 * enabling hardware crypto failed. The set_key() call may also return the
3243 * value 1 to permit this specific key/algorithm to be done in software.
3244 *
3245 * When the cmd is %DISABLE_KEY then it must succeed.
3246 *
3247 * Note that it is permissible to not decrypt a frame even if a key
3248 * for it has been uploaded to hardware. The stack will not make any
3249 * decision based on whether a key has been uploaded or not but rather
3250 * based on the receive flags.
3251 *
3252 * The &struct ieee80211_key_conf structure pointed to by the @key
3253 * parameter is guaranteed to be valid until another call to set_key()
3254 * removes it, but it can only be used as a cookie to differentiate
3255 * keys.
3256 *
3257 * In TKIP some HW need to be provided a phase 1 key, for RX decryption
3258 * acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key
3259 * handler.
3260 * The update_tkip_key() call updates the driver with the new phase 1 key.
3261 * This happens every time the iv16 wraps around (every 65536 packets). The
3262 * set_key() call will happen only once for each key (unless the AP did
3263 * rekeying); it will not include a valid phase 1 key. The valid phase 1 key is
3264 * provided by update_tkip_key only. The trigger that makes mac80211 call this
3265 * handler is software decryption with wrap around of iv16.
3266 *
3267 * The set_default_unicast_key() call updates the default WEP key index
3268 * configured to the hardware for WEP encryption type. This is required
3269 * for devices that support offload of data packets (e.g. ARP responses).
3270 *
3271 * Mac80211 drivers should set the @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 flag
3272 * when they are able to replace in-use PTK keys according to the following
3273 * requirements:
3274 * 1) They do not hand over frames decrypted with the old key to mac80211
3275 once the call to set_key() with command %DISABLE_KEY has been completed,
3276 2) either drop or continue to use the old key for any outgoing frames queued
3277 at the time of the key deletion (including re-transmits),
3278 3) never send out a frame queued prior to the set_key() %SET_KEY command
3279 encrypted with the new key when also needing
3280 @IEEE80211_KEY_FLAG_GENERATE_IV and
3281 4) never send out a frame unencrypted when it should be encrypted.
3282 Mac80211 will not queue any new frames for a deleted key to the driver.
3283 */
3284
3285/**
3286 * DOC: Powersave support
3287 *
3288 * mac80211 has support for various powersave implementations.
3289 *
3290 * First, it can support hardware that handles all powersaving by itself;
3291 * such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS hardware
3292 * flag. In that case, it will be told about the desired powersave mode
3293 * with the %IEEE80211_CONF_PS flag depending on the association status.
3294 * The hardware must take care of sending nullfunc frames when necessary,
3295 * i.e. when entering and leaving powersave mode. The hardware is required
3296 * to look at the AID in beacons and signal to the AP that it woke up when
3297 * it finds traffic directed to it.
3298 *
3299 * %IEEE80211_CONF_PS flag enabled means that the powersave mode defined in
3300 * IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused
3301 * with hardware wakeup and sleep states. Driver is responsible for waking
3302 * up the hardware before issuing commands to the hardware and putting it
3303 * back to sleep at appropriate times.
3304 *
3305 * When PS is enabled, hardware needs to wakeup for beacons and receive the
3306 * buffered multicast/broadcast frames after the beacon. Also it must be
3307 * possible to send frames and receive the acknowledment frame.
3308 *
3309 * Other hardware designs cannot send nullfunc frames by themselves and also
3310 * need software support for parsing the TIM bitmap. This is also supported
3311 * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and
3312 * %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still
3313 * required to pass up beacons. The hardware is still required to handle
3314 * waking up for multicast traffic; if it cannot the driver must handle that
3315 * as best as it can; mac80211 is too slow to do that.
3316 *
3317 * Dynamic powersave is an extension to normal powersave in which the
3318 * hardware stays awake for a user-specified period of time after sending a
3319 * frame so that reply frames need not be buffered and therefore delayed to
3320 * the next wakeup. It's a compromise of getting good enough latency when
3321 * there's data traffic and still saving significantly power in idle
3322 * periods.
3323 *
3324 * Dynamic powersave is simply supported by mac80211 enabling and disabling
3325 * PS based on traffic. Driver needs to only set %IEEE80211_HW_SUPPORTS_PS
3326 * flag and mac80211 will handle everything automatically. Additionally,
3327 * hardware having support for the dynamic PS feature may set the
3328 * %IEEE80211_HW_SUPPORTS_DYNAMIC_PS flag to indicate that it can support
3329 * dynamic PS mode itself. The driver needs to look at the
3330 * @dynamic_ps_timeout hardware configuration value and use it that value
3331 * whenever %IEEE80211_CONF_PS is set. In this case mac80211 will disable
3332 * dynamic PS feature in stack and will just keep %IEEE80211_CONF_PS
3333 * enabled whenever user has enabled powersave.
3334 *
3335 * Driver informs U-APSD client support by enabling
3336 * %IEEE80211_VIF_SUPPORTS_UAPSD flag. The mode is configured through the
3337 * uapsd parameter in conf_tx() operation. Hardware needs to send the QoS
3338 * Nullfunc frames and stay awake until the service period has ended. To
3339 * utilize U-APSD, dynamic powersave is disabled for voip AC and all frames
3340 * from that AC are transmitted with powersave enabled.
3341 *
3342 * Note: U-APSD client mode is not yet supported with
3343 * %IEEE80211_HW_PS_NULLFUNC_STACK.
3344 */
3345
3346/**
3347 * DOC: Beacon filter support
3348 *
3349 * Some hardware have beacon filter support to reduce host cpu wakeups
3350 * which will reduce system power consumption. It usually works so that
3351 * the firmware creates a checksum of the beacon but omits all constantly
3352 * changing elements (TSF, TIM etc). Whenever the checksum changes the
3353 * beacon is forwarded to the host, otherwise it will be just dropped. That
3354 * way the host will only receive beacons where some relevant information
3355 * (for example ERP protection or WMM settings) have changed.
3356 *
3357 * Beacon filter support is advertised with the %IEEE80211_VIF_BEACON_FILTER
3358 * interface capability. The driver needs to enable beacon filter support
3359 * whenever power save is enabled, that is %IEEE80211_CONF_PS is set. When
3360 * power save is enabled, the stack will not check for beacon loss and the
3361 * driver needs to notify about loss of beacons with ieee80211_beacon_loss().
3362 *
3363 * The time (or number of beacons missed) until the firmware notifies the
3364 * driver of a beacon loss event (which in turn causes the driver to call
3365 * ieee80211_beacon_loss()) should be configurable and will be controlled
3366 * by mac80211 and the roaming algorithm in the future.
3367 *
3368 * Since there may be constantly changing information elements that nothing
3369 * in the software stack cares about, we will, in the future, have mac80211
3370 * tell the driver which information elements are interesting in the sense
3371 * that we want to see changes in them. This will include
3372 *
3373 * - a list of information element IDs
3374 * - a list of OUIs for the vendor information element
3375 *
3376 * Ideally, the hardware would filter out any beacons without changes in the
3377 * requested elements, but if it cannot support that it may, at the expense
3378 * of some efficiency, filter out only a subset. For example, if the device
3379 * doesn't support checking for OUIs it should pass up all changes in all
3380 * vendor information elements.
3381 *
3382 * Note that change, for the sake of simplification, also includes information
3383 * elements appearing or disappearing from the beacon.
3384 *
3385 * Some hardware supports an "ignore list" instead. Just make sure nothing
3386 * that was requested is on the ignore list, and include commonly changing
3387 * information element IDs in the ignore list, for example 11 (BSS load) and
3388 * the various vendor-assigned IEs with unknown contents (128, 129, 133-136,
3389 * 149, 150, 155, 156, 173, 176, 178, 179, 219); for forward compatibility
3390 * it could also include some currently unused IDs.
3391 *
3392 *
3393 * In addition to these capabilities, hardware should support notifying the
3394 * host of changes in the beacon RSSI. This is relevant to implement roaming
3395 * when no traffic is flowing (when traffic is flowing we see the RSSI of
3396 * the received data packets). This can consist of notifying the host when
3397 * the RSSI changes significantly or when it drops below or rises above
3398 * configurable thresholds. In the future these thresholds will also be
3399 * configured by mac80211 (which gets them from userspace) to implement
3400 * them as the roaming algorithm requires.
3401 *
3402 * If the hardware cannot implement this, the driver should ask it to
3403 * periodically pass beacon frames to the host so that software can do the
3404 * signal strength threshold checking.
3405 */
3406
3407/**
3408 * DOC: Spatial multiplexing power save
3409 *
3410 * SMPS (Spatial multiplexing power save) is a mechanism to conserve
3411 * power in an 802.11n implementation. For details on the mechanism
3412 * and rationale, please refer to 802.11 (as amended by 802.11n-2009)
3413 * "11.2.3 SM power save".
3414 *
3415 * The mac80211 implementation is capable of sending action frames
3416 * to update the AP about the station's SMPS mode, and will instruct
3417 * the driver to enter the specific mode. It will also announce the
3418 * requested SMPS mode during the association handshake. Hardware
3419 * support for this feature is required, and can be indicated by
3420 * hardware flags.
3421 *
3422 * The default mode will be "automatic", which nl80211/cfg80211
3423 * defines to be dynamic SMPS in (regular) powersave, and SMPS
3424 * turned off otherwise.
3425 *
3426 * To support this feature, the driver must set the appropriate
3427 * hardware support flags, and handle the SMPS flag to the config()
3428 * operation. It will then with this mechanism be instructed to
3429 * enter the requested SMPS mode while associated to an HT AP.
3430 */
3431
3432/**
3433 * DOC: Frame filtering
3434 *
3435 * mac80211 requires to see many management frames for proper
3436 * operation, and users may want to see many more frames when
3437 * in monitor mode. However, for best CPU usage and power consumption,
3438 * having as few frames as possible percolate through the stack is
3439 * desirable. Hence, the hardware should filter as much as possible.
3440 *
3441 * To achieve this, mac80211 uses filter flags (see below) to tell
3442 * the driver's configure_filter() function which frames should be
3443 * passed to mac80211 and which should be filtered out.
3444 *
3445 * Before configure_filter() is invoked, the prepare_multicast()
3446 * callback is invoked with the parameters @mc_count and @mc_list
3447 * for the combined multicast address list of all virtual interfaces.
3448 * It's use is optional, and it returns a u64 that is passed to
3449 * configure_filter(). Additionally, configure_filter() has the
3450 * arguments @changed_flags telling which flags were changed and
3451 * @total_flags with the new flag states.
3452 *
3453 * If your device has no multicast address filters your driver will
3454 * need to check both the %FIF_ALLMULTI flag and the @mc_count
3455 * parameter to see whether multicast frames should be accepted
3456 * or dropped.
3457 *
3458 * All unsupported flags in @total_flags must be cleared.
3459 * Hardware does not support a flag if it is incapable of _passing_
3460 * the frame to the stack. Otherwise the driver must ignore
3461 * the flag, but not clear it.
3462 * You must _only_ clear the flag (announce no support for the
3463 * flag to mac80211) if you are not able to pass the packet type
3464 * to the stack (so the hardware always filters it).
3465 * So for example, you should clear @FIF_CONTROL, if your hardware
3466 * always filters control frames. If your hardware always passes
3467 * control frames to the kernel and is incapable of filtering them,
3468 * you do _not_ clear the @FIF_CONTROL flag.
3469 * This rule applies to all other FIF flags as well.
3470 */
3471
3472/**
3473 * DOC: AP support for powersaving clients
3474 *
3475 * In order to implement AP and P2P GO modes, mac80211 has support for
3476 * client powersaving, both "legacy" PS (PS-Poll/null data) and uAPSD.
3477 * There currently is no support for sAPSD.
3478 *
3479 * There is one assumption that mac80211 makes, namely that a client
3480 * will not poll with PS-Poll and trigger with uAPSD at the same time.
3481 * Both are supported, and both can be used by the same client, but
3482 * they can't be used concurrently by the same client. This simplifies
3483 * the driver code.
3484 *
3485 * The first thing to keep in mind is that there is a flag for complete
3486 * driver implementation: %IEEE80211_HW_AP_LINK_PS. If this flag is set,
3487 * mac80211 expects the driver to handle most of the state machine for
3488 * powersaving clients and will ignore the PM bit in incoming frames.
3489 * Drivers then use ieee80211_sta_ps_transition() to inform mac80211 of
3490 * stations' powersave transitions. In this mode, mac80211 also doesn't
3491 * handle PS-Poll/uAPSD.
3492 *
3493 * In the mode without %IEEE80211_HW_AP_LINK_PS, mac80211 will check the
3494 * PM bit in incoming frames for client powersave transitions. When a
3495 * station goes to sleep, we will stop transmitting to it. There is,
3496 * however, a race condition: a station might go to sleep while there is
3497 * data buffered on hardware queues. If the device has support for this
3498 * it will reject frames, and the driver should give the frames back to
3499 * mac80211 with the %IEEE80211_TX_STAT_TX_FILTERED flag set which will
3500 * cause mac80211 to retry the frame when the station wakes up. The
3501 * driver is also notified of powersave transitions by calling its
3502 * @sta_notify callback.
3503 *
3504 * When the station is asleep, it has three choices: it can wake up,
3505 * it can PS-Poll, or it can possibly start a uAPSD service period.
3506 * Waking up is implemented by simply transmitting all buffered (and
3507 * filtered) frames to the station. This is the easiest case. When
3508 * the station sends a PS-Poll or a uAPSD trigger frame, mac80211
3509 * will inform the driver of this with the @allow_buffered_frames
3510 * callback; this callback is optional. mac80211 will then transmit
3511 * the frames as usual and set the %IEEE80211_TX_CTL_NO_PS_BUFFER
3512 * on each frame. The last frame in the service period (or the only
3513 * response to a PS-Poll) also has %IEEE80211_TX_STATUS_EOSP set to
3514 * indicate that it ends the service period; as this frame must have
3515 * TX status report it also sets %IEEE80211_TX_CTL_REQ_TX_STATUS.
3516 * When TX status is reported for this frame, the service period is
3517 * marked has having ended and a new one can be started by the peer.
3518 *
3519 * Additionally, non-bufferable MMPDUs can also be transmitted by
3520 * mac80211 with the %IEEE80211_TX_CTL_NO_PS_BUFFER set in them.
3521 *
3522 * Another race condition can happen on some devices like iwlwifi
3523 * when there are frames queued for the station and it wakes up
3524 * or polls; the frames that are already queued could end up being
3525 * transmitted first instead, causing reordering and/or wrong
3526 * processing of the EOSP. The cause is that allowing frames to be
3527 * transmitted to a certain station is out-of-band communication to
3528 * the device. To allow this problem to be solved, the driver can
3529 * call ieee80211_sta_block_awake() if frames are buffered when it
3530 * is notified that the station went to sleep. When all these frames
3531 * have been filtered (see above), it must call the function again
3532 * to indicate that the station is no longer blocked.
3533 *
3534 * If the driver buffers frames in the driver for aggregation in any
3535 * way, it must use the ieee80211_sta_set_buffered() call when it is
3536 * notified of the station going to sleep to inform mac80211 of any
3537 * TIDs that have frames buffered. Note that when a station wakes up
3538 * this information is reset (hence the requirement to call it when
3539 * informed of the station going to sleep). Then, when a service
3540 * period starts for any reason, @release_buffered_frames is called
3541 * with the number of frames to be released and which TIDs they are
3542 * to come from. In this case, the driver is responsible for setting
3543 * the EOSP (for uAPSD) and MORE_DATA bits in the released frames.
3544 * To help the @more_data parameter is passed to tell the driver if
3545 * there is more data on other TIDs -- the TIDs to release frames
3546 * from are ignored since mac80211 doesn't know how many frames the
3547 * buffers for those TIDs contain.
3548 *
3549 * If the driver also implement GO mode, where absence periods may
3550 * shorten service periods (or abort PS-Poll responses), it must
3551 * filter those response frames except in the case of frames that
3552 * are buffered in the driver -- those must remain buffered to avoid
3553 * reordering. Because it is possible that no frames are released
3554 * in this case, the driver must call ieee80211_sta_eosp()
3555 * to indicate to mac80211 that the service period ended anyway.
3556 *
3557 * Finally, if frames from multiple TIDs are released from mac80211
3558 * but the driver might reorder them, it must clear & set the flags
3559 * appropriately (only the last frame may have %IEEE80211_TX_STATUS_EOSP)
3560 * and also take care of the EOSP and MORE_DATA bits in the frame.
3561 * The driver may also use ieee80211_sta_eosp() in this case.
3562 *
3563 * Note that if the driver ever buffers frames other than QoS-data
3564 * frames, it must take care to never send a non-QoS-data frame as
3565 * the last frame in a service period, adding a QoS-nulldata frame
3566 * after a non-QoS-data frame if needed.
3567 */
3568
3569/**
3570 * DOC: HW queue control
3571 *
3572 * Before HW queue control was introduced, mac80211 only had a single static
3573 * assignment of per-interface AC software queues to hardware queues. This
3574 * was problematic for a few reasons:
3575 * 1) off-channel transmissions might get stuck behind other frames
3576 * 2) multiple virtual interfaces couldn't be handled correctly
3577 * 3) after-DTIM frames could get stuck behind other frames
3578 *
3579 * To solve this, hardware typically uses multiple different queues for all
3580 * the different usages, and this needs to be propagated into mac80211 so it
3581 * won't have the same problem with the software queues.
3582 *
3583 * Therefore, mac80211 now offers the %IEEE80211_HW_QUEUE_CONTROL capability
3584 * flag that tells it that the driver implements its own queue control. To do
3585 * so, the driver will set up the various queues in each &struct ieee80211_vif
3586 * and the offchannel queue in &struct ieee80211_hw. In response, mac80211 will
3587 * use those queue IDs in the hw_queue field of &struct ieee80211_tx_info and
3588 * if necessary will queue the frame on the right software queue that mirrors
3589 * the hardware queue.
3590 * Additionally, the driver has to then use these HW queue IDs for the queue
3591 * management functions (ieee80211_stop_queue() et al.)
3592 *
3593 * The driver is free to set up the queue mappings as needed; multiple virtual
3594 * interfaces may map to the same hardware queues if needed. The setup has to
3595 * happen during add_interface or change_interface callbacks. For example, a
3596 * driver supporting station+station and station+AP modes might decide to have
3597 * 10 hardware queues to handle different scenarios:
3598 *
3599 * 4 AC HW queues for 1st vif: 0, 1, 2, 3
3600 * 4 AC HW queues for 2nd vif: 4, 5, 6, 7
3601 * after-DTIM queue for AP: 8
3602 * off-channel queue: 9
3603 *
3604 * It would then set up the hardware like this:
3605 * hw.offchannel_tx_hw_queue = 9
3606 *
3607 * and the first virtual interface that is added as follows:
3608 * vif.hw_queue[IEEE80211_AC_VO] = 0
3609 * vif.hw_queue[IEEE80211_AC_VI] = 1
3610 * vif.hw_queue[IEEE80211_AC_BE] = 2
3611 * vif.hw_queue[IEEE80211_AC_BK] = 3
3612 * vif.cab_queue = 8 // if AP mode, otherwise %IEEE80211_INVAL_HW_QUEUE
3613 * and the second virtual interface with 4-7.
3614 *
3615 * If queue 6 gets full, for example, mac80211 would only stop the second
3616 * virtual interface's BE queue since virtual interface queues are per AC.
3617 *
3618 * Note that the vif.cab_queue value should be set to %IEEE80211_INVAL_HW_QUEUE
3619 * whenever the queue is not used (i.e. the interface is not in AP mode) if the
3620 * queue could potentially be shared since mac80211 will look at cab_queue when
3621 * a queue is stopped/woken even if the interface is not in AP mode.
3622 */
3623
3624/**
3625 * enum ieee80211_filter_flags - hardware filter flags
3626 *
3627 * These flags determine what the filter in hardware should be
3628 * programmed to let through and what should not be passed to the
3629 * stack. It is always safe to pass more frames than requested,
3630 * but this has negative impact on power consumption.
3631 *
3632 * @FIF_ALLMULTI: pass all multicast frames, this is used if requested
3633 * by the user or if the hardware is not capable of filtering by
3634 * multicast address.
3635 *
3636 * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the
3637 * %RX_FLAG_FAILED_FCS_CRC for them)
3638 *
3639 * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set
3640 * the %RX_FLAG_FAILED_PLCP_CRC for them
3641 *
3642 * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate
3643 * to the hardware that it should not filter beacons or probe responses
3644 * by BSSID. Filtering them can greatly reduce the amount of processing
3645 * mac80211 needs to do and the amount of CPU wakeups, so you should
3646 * honour this flag if possible.
3647 *
3648 * @FIF_CONTROL: pass control frames (except for PS Poll) addressed to this
3649 * station
3650 *
3651 * @FIF_OTHER_BSS: pass frames destined to other BSSes
3652 *
3653 * @FIF_PSPOLL: pass PS Poll frames
3654 *
3655 * @FIF_PROBE_REQ: pass probe request frames
3656 *
3657 * @FIF_MCAST_ACTION: pass multicast Action frames
3658 */
3659enum ieee80211_filter_flags {
3660 FIF_ALLMULTI = 1<<1,
3661 FIF_FCSFAIL = 1<<2,
3662 FIF_PLCPFAIL = 1<<3,
3663 FIF_BCN_PRBRESP_PROMISC = 1<<4,
3664 FIF_CONTROL = 1<<5,
3665 FIF_OTHER_BSS = 1<<6,
3666 FIF_PSPOLL = 1<<7,
3667 FIF_PROBE_REQ = 1<<8,
3668 FIF_MCAST_ACTION = 1<<9,
3669};
3670
3671/**
3672 * enum ieee80211_ampdu_mlme_action - A-MPDU actions
3673 *
3674 * These flags are used with the ampdu_action() callback in
3675 * &struct ieee80211_ops to indicate which action is needed.
3676 *
3677 * Note that drivers MUST be able to deal with a TX aggregation
3678 * session being stopped even before they OK'ed starting it by
3679 * calling ieee80211_start_tx_ba_cb_irqsafe, because the peer
3680 * might receive the addBA frame and send a delBA right away!
3681 *
3682 * @IEEE80211_AMPDU_RX_START: start RX aggregation
3683 * @IEEE80211_AMPDU_RX_STOP: stop RX aggregation
3684 * @IEEE80211_AMPDU_TX_START: start TX aggregation, the driver must either
3685 * call ieee80211_start_tx_ba_cb_irqsafe() or
3686 * call ieee80211_start_tx_ba_cb_irqsafe() with status
3687 * %IEEE80211_AMPDU_TX_START_DELAY_ADDBA to delay addba after
3688 * ieee80211_start_tx_ba_cb_irqsafe is called, or just return the special
3689 * status %IEEE80211_AMPDU_TX_START_IMMEDIATE.
3690 * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational
3691 * @IEEE80211_AMPDU_TX_STOP_CONT: stop TX aggregation but continue transmitting
3692 * queued packets, now unaggregated. After all packets are transmitted the
3693 * driver has to call ieee80211_stop_tx_ba_cb_irqsafe().
3694 * @IEEE80211_AMPDU_TX_STOP_FLUSH: stop TX aggregation and flush all packets,
3695 * called when the station is removed. There's no need or reason to call
3696 * ieee80211_stop_tx_ba_cb_irqsafe() in this case as mac80211 assumes the
3697 * session is gone and removes the station.
3698 * @IEEE80211_AMPDU_TX_STOP_FLUSH_CONT: called when TX aggregation is stopped
3699 * but the driver hasn't called ieee80211_stop_tx_ba_cb_irqsafe() yet and
3700 * now the connection is dropped and the station will be removed. Drivers
3701 * should clean up and drop remaining packets when this is called.
3702 */
3703enum ieee80211_ampdu_mlme_action {
3704 IEEE80211_AMPDU_RX_START,
3705 IEEE80211_AMPDU_RX_STOP,
3706 IEEE80211_AMPDU_TX_START,
3707 IEEE80211_AMPDU_TX_STOP_CONT,
3708 IEEE80211_AMPDU_TX_STOP_FLUSH,
3709 IEEE80211_AMPDU_TX_STOP_FLUSH_CONT,
3710 IEEE80211_AMPDU_TX_OPERATIONAL,
3711};
3712
3713#define IEEE80211_AMPDU_TX_START_IMMEDIATE 1
3714#define IEEE80211_AMPDU_TX_START_DELAY_ADDBA 2
3715
3716/**
3717 * struct ieee80211_ampdu_params - AMPDU action parameters
3718 *
3719 * @action: the ampdu action, value from %ieee80211_ampdu_mlme_action.
3720 * @sta: peer of this AMPDU session
3721 * @tid: tid of the BA session
3722 * @ssn: start sequence number of the session. TX/RX_STOP can pass 0. When
3723 * action is set to %IEEE80211_AMPDU_RX_START the driver passes back the
3724 * actual ssn value used to start the session and writes the value here.
3725 * @buf_size: reorder buffer size (number of subframes). Valid only when the
3726 * action is set to %IEEE80211_AMPDU_RX_START or
3727 * %IEEE80211_AMPDU_TX_OPERATIONAL
3728 * @amsdu: indicates the peer's ability to receive A-MSDU within A-MPDU.
3729 * valid when the action is set to %IEEE80211_AMPDU_TX_OPERATIONAL
3730 * @timeout: BA session timeout. Valid only when the action is set to
3731 * %IEEE80211_AMPDU_RX_START
3732 */
3733struct ieee80211_ampdu_params {
3734 enum ieee80211_ampdu_mlme_action action;
3735 struct ieee80211_sta *sta;
3736 u16 tid;
3737 u16 ssn;
3738 u16 buf_size;
3739 bool amsdu;
3740 u16 timeout;
3741};
3742
3743/**
3744 * enum ieee80211_frame_release_type - frame release reason
3745 * @IEEE80211_FRAME_RELEASE_PSPOLL: frame released for PS-Poll
3746 * @IEEE80211_FRAME_RELEASE_UAPSD: frame(s) released due to
3747 * frame received on trigger-enabled AC
3748 */
3749enum ieee80211_frame_release_type {
3750 IEEE80211_FRAME_RELEASE_PSPOLL,
3751 IEEE80211_FRAME_RELEASE_UAPSD,
3752};
3753
3754/**
3755 * enum ieee80211_rate_control_changed - flags to indicate what changed
3756 *
3757 * @IEEE80211_RC_BW_CHANGED: The bandwidth that can be used to transmit
3758 * to this station changed. The actual bandwidth is in the station
3759 * information -- for HT20/40 the IEEE80211_HT_CAP_SUP_WIDTH_20_40
3760 * flag changes, for HT and VHT the bandwidth field changes.
3761 * @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed.
3762 * @IEEE80211_RC_SUPP_RATES_CHANGED: The supported rate set of this peer
3763 * changed (in IBSS mode) due to discovering more information about
3764 * the peer.
3765 * @IEEE80211_RC_NSS_CHANGED: N_SS (number of spatial streams) was changed
3766 * by the peer
3767 */
3768enum ieee80211_rate_control_changed {
3769 IEEE80211_RC_BW_CHANGED = BIT(0),
3770 IEEE80211_RC_SMPS_CHANGED = BIT(1),
3771 IEEE80211_RC_SUPP_RATES_CHANGED = BIT(2),
3772 IEEE80211_RC_NSS_CHANGED = BIT(3),
3773};
3774
3775/**
3776 * enum ieee80211_roc_type - remain on channel type
3777 *
3778 * With the support for multi channel contexts and multi channel operations,
3779 * remain on channel operations might be limited/deferred/aborted by other
3780 * flows/operations which have higher priority (and vice versa).
3781 * Specifying the ROC type can be used by devices to prioritize the ROC
3782 * operations compared to other operations/flows.
3783 *
3784 * @IEEE80211_ROC_TYPE_NORMAL: There are no special requirements for this ROC.
3785 * @IEEE80211_ROC_TYPE_MGMT_TX: The remain on channel request is required
3786 * for sending management frames offchannel.
3787 */
3788enum ieee80211_roc_type {
3789 IEEE80211_ROC_TYPE_NORMAL = 0,
3790 IEEE80211_ROC_TYPE_MGMT_TX,
3791};
3792
3793/**
3794 * enum ieee80211_reconfig_type - reconfig type
3795 *
3796 * This enum is used by the reconfig_complete() callback to indicate what
3797 * reconfiguration type was completed.
3798 *
3799 * @IEEE80211_RECONFIG_TYPE_RESTART: hw restart type
3800 * (also due to resume() callback returning 1)
3801 * @IEEE80211_RECONFIG_TYPE_SUSPEND: suspend type (regardless
3802 * of wowlan configuration)
3803 */
3804enum ieee80211_reconfig_type {
3805 IEEE80211_RECONFIG_TYPE_RESTART,
3806 IEEE80211_RECONFIG_TYPE_SUSPEND,
3807};
3808
3809/**
3810 * struct ieee80211_prep_tx_info - prepare TX information
3811 * @duration: if non-zero, hint about the required duration,
3812 * only used with the mgd_prepare_tx() method.
3813 * @subtype: frame subtype (auth, (re)assoc, deauth, disassoc)
3814 * @success: whether the frame exchange was successful, only
3815 * used with the mgd_complete_tx() method, and then only
3816 * valid for auth and (re)assoc.
3817 * @was_assoc: set if this call is due to deauth/disassoc
3818 * while just having been associated
3819 * @link_id: the link id on which the frame will be TX'ed.
3820 * Only used with the mgd_prepare_tx() method.
3821 */
3822struct ieee80211_prep_tx_info {
3823 u16 duration;
3824 u16 subtype;
3825 u8 success:1, was_assoc:1;
3826 int link_id;
3827};
3828
3829/**
3830 * struct ieee80211_ops - callbacks from mac80211 to the driver
3831 *
3832 * This structure contains various callbacks that the driver may
3833 * handle or, in some cases, must handle, for example to configure
3834 * the hardware to a new channel or to transmit a frame.
3835 *
3836 * @tx: Handler that 802.11 module calls for each transmitted frame.
3837 * skb contains the buffer starting from the IEEE 802.11 header.
3838 * The low-level driver should send the frame out based on
3839 * configuration in the TX control data. This handler should,
3840 * preferably, never fail and stop queues appropriately.
3841 * Must be atomic.
3842 *
3843 * @start: Called before the first netdevice attached to the hardware
3844 * is enabled. This should turn on the hardware and must turn on
3845 * frame reception (for possibly enabled monitor interfaces.)
3846 * Returns negative error codes, these may be seen in userspace,
3847 * or zero.
3848 * When the device is started it should not have a MAC address
3849 * to avoid acknowledging frames before a non-monitor device
3850 * is added.
3851 * Must be implemented and can sleep.
3852 *
3853 * @stop: Called after last netdevice attached to the hardware
3854 * is disabled. This should turn off the hardware (at least
3855 * it must turn off frame reception.)
3856 * May be called right after add_interface if that rejects
3857 * an interface. If you added any work onto the mac80211 workqueue
3858 * you should ensure to cancel it on this callback.
3859 * Must be implemented and can sleep.
3860 *
3861 * @suspend: Suspend the device; mac80211 itself will quiesce before and
3862 * stop transmitting and doing any other configuration, and then
3863 * ask the device to suspend. This is only invoked when WoWLAN is
3864 * configured, otherwise the device is deconfigured completely and
3865 * reconfigured at resume time.
3866 * The driver may also impose special conditions under which it
3867 * wants to use the "normal" suspend (deconfigure), say if it only
3868 * supports WoWLAN when the device is associated. In this case, it
3869 * must return 1 from this function.
3870 *
3871 * @resume: If WoWLAN was configured, this indicates that mac80211 is
3872 * now resuming its operation, after this the device must be fully
3873 * functional again. If this returns an error, the only way out is
3874 * to also unregister the device. If it returns 1, then mac80211
3875 * will also go through the regular complete restart on resume.
3876 *
3877 * @set_wakeup: Enable or disable wakeup when WoWLAN configuration is
3878 * modified. The reason is that device_set_wakeup_enable() is
3879 * supposed to be called when the configuration changes, not only
3880 * in suspend().
3881 *
3882 * @add_interface: Called when a netdevice attached to the hardware is
3883 * enabled. Because it is not called for monitor mode devices, @start
3884 * and @stop must be implemented.
3885 * The driver should perform any initialization it needs before
3886 * the device can be enabled. The initial configuration for the
3887 * interface is given in the conf parameter.
3888 * The callback may refuse to add an interface by returning a
3889 * negative error code (which will be seen in userspace.)
3890 * Must be implemented and can sleep.
3891 *
3892 * @change_interface: Called when a netdevice changes type. This callback
3893 * is optional, but only if it is supported can interface types be
3894 * switched while the interface is UP. The callback may sleep.
3895 * Note that while an interface is being switched, it will not be
3896 * found by the interface iteration callbacks.
3897 *
3898 * @remove_interface: Notifies a driver that an interface is going down.
3899 * The @stop callback is called after this if it is the last interface
3900 * and no monitor interfaces are present.
3901 * When all interfaces are removed, the MAC address in the hardware
3902 * must be cleared so the device no longer acknowledges packets,
3903 * the mac_addr member of the conf structure is, however, set to the
3904 * MAC address of the device going away.
3905 * Hence, this callback must be implemented. It can sleep.
3906 *
3907 * @config: Handler for configuration requests. IEEE 802.11 code calls this
3908 * function to change hardware configuration, e.g., channel.
3909 * This function should never fail but returns a negative error code
3910 * if it does. The callback can sleep.
3911 *
3912 * @bss_info_changed: Handler for configuration requests related to BSS
3913 * parameters that may vary during BSS's lifespan, and may affect low
3914 * level driver (e.g. assoc/disassoc status, erp parameters).
3915 * This function should not be used if no BSS has been set, unless
3916 * for association indication. The @changed parameter indicates which
3917 * of the bss parameters has changed when a call is made. The callback
3918 * can sleep.
3919 * Note: this callback is called if @vif_cfg_changed or @link_info_changed
3920 * are not implemented.
3921 *
3922 * @vif_cfg_changed: Handler for configuration requests related to interface
3923 * (MLD) parameters from &struct ieee80211_vif_cfg that vary during the
3924 * lifetime of the interface (e.g. assoc status, IP addresses, etc.)
3925 * The @changed parameter indicates which value changed.
3926 * The callback can sleep.
3927 *
3928 * @link_info_changed: Handler for configuration requests related to link
3929 * parameters from &struct ieee80211_bss_conf that are related to an
3930 * individual link. e.g. legacy/HT/VHT/... rate information.
3931 * The @changed parameter indicates which value changed, and the @link_id
3932 * parameter indicates the link ID. Note that the @link_id will be 0 for
3933 * non-MLO connections.
3934 * The callback can sleep.
3935 *
3936 * @prepare_multicast: Prepare for multicast filter configuration.
3937 * This callback is optional, and its return value is passed
3938 * to configure_filter(). This callback must be atomic.
3939 *
3940 * @configure_filter: Configure the device's RX filter.
3941 * See the section "Frame filtering" for more information.
3942 * This callback must be implemented and can sleep.
3943 *
3944 * @config_iface_filter: Configure the interface's RX filter.
3945 * This callback is optional and is used to configure which frames
3946 * should be passed to mac80211. The filter_flags is the combination
3947 * of FIF_* flags. The changed_flags is a bit mask that indicates
3948 * which flags are changed.
3949 * This callback can sleep.
3950 *
3951 * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit
3952 * must be set or cleared for a given STA. Must be atomic.
3953 *
3954 * @set_key: See the section "Hardware crypto acceleration"
3955 * This callback is only called between add_interface and
3956 * remove_interface calls, i.e. while the given virtual interface
3957 * is enabled.
3958 * Returns a negative error code if the key can't be added.
3959 * The callback can sleep.
3960 *
3961 * @update_tkip_key: See the section "Hardware crypto acceleration"
3962 * This callback will be called in the context of Rx. Called for drivers
3963 * which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY.
3964 * The callback must be atomic.
3965 *
3966 * @set_rekey_data: If the device supports GTK rekeying, for example while the
3967 * host is suspended, it can assign this callback to retrieve the data
3968 * necessary to do GTK rekeying, this is the KEK, KCK and replay counter.
3969 * After rekeying was done it should (for example during resume) notify
3970 * userspace of the new replay counter using ieee80211_gtk_rekey_notify().
3971 *
3972 * @set_default_unicast_key: Set the default (unicast) key index, useful for
3973 * WEP when the device sends data packets autonomously, e.g. for ARP
3974 * offloading. The index can be 0-3, or -1 for unsetting it.
3975 *
3976 * @hw_scan: Ask the hardware to service the scan request, no need to start
3977 * the scan state machine in stack. The scan must honour the channel
3978 * configuration done by the regulatory agent in the wiphy's
3979 * registered bands. The hardware (or the driver) needs to make sure
3980 * that power save is disabled.
3981 * The @req ie/ie_len members are rewritten by mac80211 to contain the
3982 * entire IEs after the SSID, so that drivers need not look at these
3983 * at all but just send them after the SSID -- mac80211 includes the
3984 * (extended) supported rates and HT information (where applicable).
3985 * When the scan finishes, ieee80211_scan_completed() must be called;
3986 * note that it also must be called when the scan cannot finish due to
3987 * any error unless this callback returned a negative error code.
3988 * This callback is also allowed to return the special return value 1,
3989 * this indicates that hardware scan isn't desirable right now and a
3990 * software scan should be done instead. A driver wishing to use this
3991 * capability must ensure its (hardware) scan capabilities aren't
3992 * advertised as more capable than mac80211's software scan is.
3993 * The callback can sleep.
3994 *
3995 * @cancel_hw_scan: Ask the low-level tp cancel the active hw scan.
3996 * The driver should ask the hardware to cancel the scan (if possible),
3997 * but the scan will be completed only after the driver will call
3998 * ieee80211_scan_completed().
3999 * This callback is needed for wowlan, to prevent enqueueing a new
4000 * scan_work after the low-level driver was already suspended.
4001 * The callback can sleep.
4002 *
4003 * @sched_scan_start: Ask the hardware to start scanning repeatedly at
4004 * specific intervals. The driver must call the
4005 * ieee80211_sched_scan_results() function whenever it finds results.
4006 * This process will continue until sched_scan_stop is called.
4007 *
4008 * @sched_scan_stop: Tell the hardware to stop an ongoing scheduled scan.
4009 * In this case, ieee80211_sched_scan_stopped() must not be called.
4010 *
4011 * @sw_scan_start: Notifier function that is called just before a software scan
4012 * is started. Can be NULL, if the driver doesn't need this notification.
4013 * The mac_addr parameter allows supporting NL80211_SCAN_FLAG_RANDOM_ADDR,
4014 * the driver may set the NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR flag if it
4015 * can use this parameter. The callback can sleep.
4016 *
4017 * @sw_scan_complete: Notifier function that is called just after a
4018 * software scan finished. Can be NULL, if the driver doesn't need
4019 * this notification.
4020 * The callback can sleep.
4021 *
4022 * @get_stats: Return low-level statistics.
4023 * Returns zero if statistics are available.
4024 * The callback can sleep.
4025 *
4026 * @get_key_seq: If your device implements encryption in hardware and does
4027 * IV/PN assignment then this callback should be provided to read the
4028 * IV/PN for the given key from hardware.
4029 * The callback must be atomic.
4030 *
4031 * @set_frag_threshold: Configuration of fragmentation threshold. Assign this
4032 * if the device does fragmentation by itself. Note that to prevent the
4033 * stack from doing fragmentation IEEE80211_HW_SUPPORTS_TX_FRAG
4034 * should be set as well.
4035 * The callback can sleep.
4036 *
4037 * @set_rts_threshold: Configuration of RTS threshold (if device needs it)
4038 * The callback can sleep.
4039 *
4040 * @sta_add: Notifies low level driver about addition of an associated station,
4041 * AP, IBSS/WDS/mesh peer etc. This callback can sleep.
4042 *
4043 * @sta_remove: Notifies low level driver about removal of an associated
4044 * station, AP, IBSS/WDS/mesh peer etc. Note that after the callback
4045 * returns it isn't safe to use the pointer, not even RCU protected;
4046 * no RCU grace period is guaranteed between returning here and freeing
4047 * the station. See @sta_pre_rcu_remove if needed.
4048 * This callback can sleep.
4049 *
4050 * @vif_add_debugfs: Drivers can use this callback to add a debugfs vif
4051 * directory with its files. This callback should be within a
4052 * CONFIG_MAC80211_DEBUGFS conditional. This callback can sleep.
4053 *
4054 * @link_add_debugfs: Drivers can use this callback to add debugfs files
4055 * when a link is added to a mac80211 vif. This callback should be within
4056 * a CONFIG_MAC80211_DEBUGFS conditional. This callback can sleep.
4057 * For non-MLO the callback will be called once for the default bss_conf
4058 * with the vif's directory rather than a separate subdirectory.
4059 *
4060 * @sta_add_debugfs: Drivers can use this callback to add debugfs files
4061 * when a station is added to mac80211's station list. This callback
4062 * should be within a CONFIG_MAC80211_DEBUGFS conditional. This
4063 * callback can sleep.
4064 *
4065 * @link_sta_add_debugfs: Drivers can use this callback to add debugfs files
4066 * when a link is added to a mac80211 station. This callback
4067 * should be within a CONFIG_MAC80211_DEBUGFS conditional. This
4068 * callback can sleep.
4069 * For non-MLO the callback will be called once for the deflink with the
4070 * station's directory rather than a separate subdirectory.
4071 *
4072 * @sta_notify: Notifies low level driver about power state transition of an
4073 * associated station, AP, IBSS/WDS/mesh peer etc. For a VIF operating
4074 * in AP mode, this callback will not be called when the flag
4075 * %IEEE80211_HW_AP_LINK_PS is set. Must be atomic.
4076 *
4077 * @sta_set_txpwr: Configure the station tx power. This callback set the tx
4078 * power for the station.
4079 * This callback can sleep.
4080 *
4081 * @sta_state: Notifies low level driver about state transition of a
4082 * station (which can be the AP, a client, IBSS/WDS/mesh peer etc.)
4083 * This callback is mutually exclusive with @sta_add/@sta_remove.
4084 * It must not fail for down transitions but may fail for transitions
4085 * up the list of states. Also note that after the callback returns it
4086 * isn't safe to use the pointer, not even RCU protected - no RCU grace
4087 * period is guaranteed between returning here and freeing the station.
4088 * See @sta_pre_rcu_remove if needed.
4089 * The callback can sleep.
4090 *
4091 * @sta_pre_rcu_remove: Notify driver about station removal before RCU
4092 * synchronisation. This is useful if a driver needs to have station
4093 * pointers protected using RCU, it can then use this call to clear
4094 * the pointers instead of waiting for an RCU grace period to elapse
4095 * in @sta_state.
4096 * The callback can sleep.
4097 *
4098 * @link_sta_rc_update: Notifies the driver of changes to the bitrates that can
4099 * be used to transmit to the station. The changes are advertised with bits
4100 * from &enum ieee80211_rate_control_changed and the values are reflected
4101 * in the station data. This callback should only be used when the driver
4102 * uses hardware rate control (%IEEE80211_HW_HAS_RATE_CONTROL) since
4103 * otherwise the rate control algorithm is notified directly.
4104 * Must be atomic.
4105 * @sta_rate_tbl_update: Notifies the driver that the rate table changed. This
4106 * is only used if the configured rate control algorithm actually uses
4107 * the new rate table API, and is therefore optional. Must be atomic.
4108 *
4109 * @sta_statistics: Get statistics for this station. For example with beacon
4110 * filtering, the statistics kept by mac80211 might not be accurate, so
4111 * let the driver pre-fill the statistics. The driver can fill most of
4112 * the values (indicating which by setting the filled bitmap), but not
4113 * all of them make sense - see the source for which ones are possible.
4114 * Statistics that the driver doesn't fill will be filled by mac80211.
4115 * The callback can sleep.
4116 *
4117 * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
4118 * bursting) for a hardware TX queue.
4119 * Returns a negative error code on failure.
4120 * The callback can sleep.
4121 *
4122 * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
4123 * this is only used for IBSS mode BSSID merging and debugging. Is not a
4124 * required function.
4125 * The callback can sleep.
4126 *
4127 * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
4128 * Currently, this is only used for IBSS mode debugging. Is not a
4129 * required function.
4130 * The callback can sleep.
4131 *
4132 * @offset_tsf: Offset the TSF timer by the specified value in the
4133 * firmware/hardware. Preferred to set_tsf as it avoids delay between
4134 * calling set_tsf() and hardware getting programmed, which will show up
4135 * as TSF delay. Is not a required function.
4136 * The callback can sleep.
4137 *
4138 * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize
4139 * with other STAs in the IBSS. This is only used in IBSS mode. This
4140 * function is optional if the firmware/hardware takes full care of
4141 * TSF synchronization.
4142 * The callback can sleep.
4143 *
4144 * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
4145 * This is needed only for IBSS mode and the result of this function is
4146 * used to determine whether to reply to Probe Requests.
4147 * Returns non-zero if this device sent the last beacon.
4148 * The callback can sleep.
4149 *
4150 * @get_survey: Return per-channel survey information
4151 *
4152 * @rfkill_poll: Poll rfkill hardware state. If you need this, you also
4153 * need to set wiphy->rfkill_poll to %true before registration,
4154 * and need to call wiphy_rfkill_set_hw_state() in the callback.
4155 * The callback can sleep.
4156 *
4157 * @set_coverage_class: Set slot time for given coverage class as specified
4158 * in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout
4159 * accordingly; coverage class equals to -1 to enable ACK timeout
4160 * estimation algorithm (dynack). To disable dynack set valid value for
4161 * coverage class. This callback is not required and may sleep.
4162 *
4163 * @testmode_cmd: Implement a cfg80211 test mode command. The passed @vif may
4164 * be %NULL. The callback can sleep.
4165 * @testmode_dump: Implement a cfg80211 test mode dump. The callback can sleep.
4166 *
4167 * @flush: Flush all pending frames from the hardware queue, making sure
4168 * that the hardware queues are empty. The @queues parameter is a bitmap
4169 * of queues to flush, which is useful if different virtual interfaces
4170 * use different hardware queues; it may also indicate all queues.
4171 * If the parameter @drop is set to %true, pending frames may be dropped.
4172 * Note that vif can be NULL.
4173 * The callback can sleep.
4174 *
4175 * @flush_sta: Flush or drop all pending frames from the hardware queue(s) for
4176 * the given station, as it's about to be removed.
4177 * The callback can sleep.
4178 *
4179 * @channel_switch: Drivers that need (or want) to offload the channel
4180 * switch operation for CSAs received from the AP may implement this
4181 * callback. They must then call ieee80211_chswitch_done() to indicate
4182 * completion of the channel switch.
4183 *
4184 * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device.
4185 * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may
4186 * reject TX/RX mask combinations they cannot support by returning -EINVAL
4187 * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX).
4188 *
4189 * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant).
4190 *
4191 * @remain_on_channel: Starts an off-channel period on the given channel, must
4192 * call back to ieee80211_ready_on_channel() when on that channel. Note
4193 * that normal channel traffic is not stopped as this is intended for hw
4194 * offload. Frames to transmit on the off-channel channel are transmitted
4195 * normally except for the %IEEE80211_TX_CTL_TX_OFFCHAN flag. When the
4196 * duration (which will always be non-zero) expires, the driver must call
4197 * ieee80211_remain_on_channel_expired().
4198 * Note that this callback may be called while the device is in IDLE and
4199 * must be accepted in this case.
4200 * This callback may sleep.
4201 * @cancel_remain_on_channel: Requests that an ongoing off-channel period is
4202 * aborted before it expires. This callback may sleep.
4203 *
4204 * @set_ringparam: Set tx and rx ring sizes.
4205 *
4206 * @get_ringparam: Get tx and rx ring current and maximum sizes.
4207 *
4208 * @tx_frames_pending: Check if there is any pending frame in the hardware
4209 * queues before entering power save.
4210 *
4211 * @set_bitrate_mask: Set a mask of rates to be used for rate control selection
4212 * when transmitting a frame. Currently only legacy rates are handled.
4213 * The callback can sleep.
4214 * @event_callback: Notify driver about any event in mac80211. See
4215 * &enum ieee80211_event_type for the different types.
4216 * The callback must be atomic.
4217 *
4218 * @release_buffered_frames: Release buffered frames according to the given
4219 * parameters. In the case where the driver buffers some frames for
4220 * sleeping stations mac80211 will use this callback to tell the driver
4221 * to release some frames, either for PS-poll or uAPSD.
4222 * Note that if the @more_data parameter is %false the driver must check
4223 * if there are more frames on the given TIDs, and if there are more than
4224 * the frames being released then it must still set the more-data bit in
4225 * the frame. If the @more_data parameter is %true, then of course the
4226 * more-data bit must always be set.
4227 * The @tids parameter tells the driver which TIDs to release frames
4228 * from, for PS-poll it will always have only a single bit set.
4229 * In the case this is used for a PS-poll initiated release, the
4230 * @num_frames parameter will always be 1 so code can be shared. In
4231 * this case the driver must also set %IEEE80211_TX_STATUS_EOSP flag
4232 * on the TX status (and must report TX status) so that the PS-poll
4233 * period is properly ended. This is used to avoid sending multiple
4234 * responses for a retried PS-poll frame.
4235 * In the case this is used for uAPSD, the @num_frames parameter may be
4236 * bigger than one, but the driver may send fewer frames (it must send
4237 * at least one, however). In this case it is also responsible for
4238 * setting the EOSP flag in the QoS header of the frames. Also, when the
4239 * service period ends, the driver must set %IEEE80211_TX_STATUS_EOSP
4240 * on the last frame in the SP. Alternatively, it may call the function
4241 * ieee80211_sta_eosp() to inform mac80211 of the end of the SP.
4242 * This callback must be atomic.
4243 * @allow_buffered_frames: Prepare device to allow the given number of frames
4244 * to go out to the given station. The frames will be sent by mac80211
4245 * via the usual TX path after this call. The TX information for frames
4246 * released will also have the %IEEE80211_TX_CTL_NO_PS_BUFFER flag set
4247 * and the last one will also have %IEEE80211_TX_STATUS_EOSP set. In case
4248 * frames from multiple TIDs are released and the driver might reorder
4249 * them between the TIDs, it must set the %IEEE80211_TX_STATUS_EOSP flag
4250 * on the last frame and clear it on all others and also handle the EOSP
4251 * bit in the QoS header correctly. Alternatively, it can also call the
4252 * ieee80211_sta_eosp() function.
4253 * The @tids parameter is a bitmap and tells the driver which TIDs the
4254 * frames will be on; it will at most have two bits set.
4255 * This callback must be atomic.
4256 *
4257 * @get_et_sset_count: Ethtool API to get string-set count.
4258 * Note that the wiphy mutex is not held for this callback since it's
4259 * expected to return a static value.
4260 *
4261 * @get_et_stats: Ethtool API to get a set of u64 stats.
4262 *
4263 * @get_et_strings: Ethtool API to get a set of strings to describe stats
4264 * and perhaps other supported types of ethtool data-sets.
4265 * Note that the wiphy mutex is not held for this callback since it's
4266 * expected to return a static value.
4267 *
4268 * @mgd_prepare_tx: Prepare for transmitting a management frame for association
4269 * before associated. In multi-channel scenarios, a virtual interface is
4270 * bound to a channel before it is associated, but as it isn't associated
4271 * yet it need not necessarily be given airtime, in particular since any
4272 * transmission to a P2P GO needs to be synchronized against the GO's
4273 * powersave state. mac80211 will call this function before transmitting a
4274 * management frame prior to transmitting that frame to allow the driver
4275 * to give it channel time for the transmission, to get a response and be
4276 * able to synchronize with the GO.
4277 * The callback will be called before each transmission and upon return
4278 * mac80211 will transmit the frame right away.
4279 * Additional information is passed in the &struct ieee80211_prep_tx_info
4280 * data. If duration there is greater than zero, mac80211 hints to the
4281 * driver the duration for which the operation is requested.
4282 * The callback is optional and can (should!) sleep.
4283 * @mgd_complete_tx: Notify the driver that the response frame for a previously
4284 * transmitted frame announced with @mgd_prepare_tx was received, the data
4285 * is filled similarly to @mgd_prepare_tx though the duration is not used.
4286 *
4287 * @mgd_protect_tdls_discover: Protect a TDLS discovery session. After sending
4288 * a TDLS discovery-request, we expect a reply to arrive on the AP's
4289 * channel. We must stay on the channel (no PSM, scan, etc.), since a TDLS
4290 * setup-response is a direct packet not buffered by the AP.
4291 * mac80211 will call this function just before the transmission of a TDLS
4292 * discovery-request. The recommended period of protection is at least
4293 * 2 * (DTIM period).
4294 * The callback is optional and can sleep.
4295 *
4296 * @add_chanctx: Notifies device driver about new channel context creation.
4297 * This callback may sleep.
4298 * @remove_chanctx: Notifies device driver about channel context destruction.
4299 * This callback may sleep.
4300 * @change_chanctx: Notifies device driver about channel context changes that
4301 * may happen when combining different virtual interfaces on the same
4302 * channel context with different settings
4303 * This callback may sleep.
4304 * @assign_vif_chanctx: Notifies device driver about channel context being bound
4305 * to vif. Possible use is for hw queue remapping.
4306 * This callback may sleep.
4307 * @unassign_vif_chanctx: Notifies device driver about channel context being
4308 * unbound from vif.
4309 * This callback may sleep.
4310 * @switch_vif_chanctx: switch a number of vifs from one chanctx to
4311 * another, as specified in the list of
4312 * @ieee80211_vif_chanctx_switch passed to the driver, according
4313 * to the mode defined in &ieee80211_chanctx_switch_mode.
4314 * This callback may sleep.
4315 *
4316 * @start_ap: Start operation on the AP interface, this is called after all the
4317 * information in bss_conf is set and beacon can be retrieved. A channel
4318 * context is bound before this is called. Note that if the driver uses
4319 * software scan or ROC, this (and @stop_ap) isn't called when the AP is
4320 * just "paused" for scanning/ROC, which is indicated by the beacon being
4321 * disabled/enabled via @bss_info_changed.
4322 * @stop_ap: Stop operation on the AP interface.
4323 *
4324 * @reconfig_complete: Called after a call to ieee80211_restart_hw() and
4325 * during resume, when the reconfiguration has completed.
4326 * This can help the driver implement the reconfiguration step (and
4327 * indicate mac80211 is ready to receive frames).
4328 * This callback may sleep.
4329 *
4330 * @ipv6_addr_change: IPv6 address assignment on the given interface changed.
4331 * Currently, this is only called for managed or P2P client interfaces.
4332 * This callback is optional; it must not sleep.
4333 *
4334 * @channel_switch_beacon: Starts a channel switch to a new channel.
4335 * Beacons are modified to include CSA or ECSA IEs before calling this
4336 * function. The corresponding count fields in these IEs must be
4337 * decremented, and when they reach 1 the driver must call
4338 * ieee80211_csa_finish(). Drivers which use ieee80211_beacon_get()
4339 * get the csa counter decremented by mac80211, but must check if it is
4340 * 1 using ieee80211_beacon_counter_is_complete() after the beacon has been
4341 * transmitted and then call ieee80211_csa_finish().
4342 * If the CSA count starts as zero or 1, this function will not be called,
4343 * since there won't be any time to beacon before the switch anyway.
4344 * @pre_channel_switch: This is an optional callback that is called
4345 * before a channel switch procedure is started (ie. when a STA
4346 * gets a CSA or a userspace initiated channel-switch), allowing
4347 * the driver to prepare for the channel switch.
4348 * @post_channel_switch: This is an optional callback that is called
4349 * after a channel switch procedure is completed, allowing the
4350 * driver to go back to a normal configuration.
4351 * @abort_channel_switch: This is an optional callback that is called
4352 * when channel switch procedure was aborted, allowing the
4353 * driver to go back to a normal configuration.
4354 * @channel_switch_rx_beacon: This is an optional callback that is called
4355 * when channel switch procedure is in progress and additional beacon with
4356 * CSA IE was received, allowing driver to track changes in count.
4357 * @join_ibss: Join an IBSS (on an IBSS interface); this is called after all
4358 * information in bss_conf is set up and the beacon can be retrieved. A
4359 * channel context is bound before this is called.
4360 * @leave_ibss: Leave the IBSS again.
4361 *
4362 * @get_expected_throughput: extract the expected throughput towards the
4363 * specified station. The returned value is expressed in Kbps. It returns 0
4364 * if the RC algorithm does not have proper data to provide.
4365 *
4366 * @get_txpower: get current maximum tx power (in dBm) based on configuration
4367 * and hardware limits.
4368 *
4369 * @tdls_channel_switch: Start channel-switching with a TDLS peer. The driver
4370 * is responsible for continually initiating channel-switching operations
4371 * and returning to the base channel for communication with the AP. The
4372 * driver receives a channel-switch request template and the location of
4373 * the switch-timing IE within the template as part of the invocation.
4374 * The template is valid only within the call, and the driver can
4375 * optionally copy the skb for further re-use.
4376 * @tdls_cancel_channel_switch: Stop channel-switching with a TDLS peer. Both
4377 * peers must be on the base channel when the call completes.
4378 * @tdls_recv_channel_switch: a TDLS channel-switch related frame (request or
4379 * response) has been received from a remote peer. The driver gets
4380 * parameters parsed from the incoming frame and may use them to continue
4381 * an ongoing channel-switch operation. In addition, a channel-switch
4382 * response template is provided, together with the location of the
4383 * switch-timing IE within the template. The skb can only be used within
4384 * the function call.
4385 *
4386 * @wake_tx_queue: Called when new packets have been added to the queue.
4387 * @sync_rx_queues: Process all pending frames in RSS queues. This is a
4388 * synchronization which is needed in case driver has in its RSS queues
4389 * pending frames that were received prior to the control path action
4390 * currently taken (e.g. disassociation) but are not processed yet.
4391 *
4392 * @start_nan: join an existing NAN cluster, or create a new one.
4393 * @stop_nan: leave the NAN cluster.
4394 * @nan_change_conf: change NAN configuration. The data in cfg80211_nan_conf
4395 * contains full new configuration and changes specify which parameters
4396 * are changed with respect to the last NAN config.
4397 * The driver gets both full configuration and the changed parameters since
4398 * some devices may need the full configuration while others need only the
4399 * changed parameters.
4400 * @add_nan_func: Add a NAN function. Returns 0 on success. The data in
4401 * cfg80211_nan_func must not be referenced outside the scope of
4402 * this call.
4403 * @del_nan_func: Remove a NAN function. The driver must call
4404 * ieee80211_nan_func_terminated() with
4405 * NL80211_NAN_FUNC_TERM_REASON_USER_REQUEST reason code upon removal.
4406 * @can_aggregate_in_amsdu: Called in order to determine if HW supports
4407 * aggregating two specific frames in the same A-MSDU. The relation
4408 * between the skbs should be symmetric and transitive. Note that while
4409 * skb is always a real frame, head may or may not be an A-MSDU.
4410 * @get_ftm_responder_stats: Retrieve FTM responder statistics, if available.
4411 * Statistics should be cumulative, currently no way to reset is provided.
4412 *
4413 * @start_pmsr: start peer measurement (e.g. FTM) (this call can sleep)
4414 * @abort_pmsr: abort peer measurement (this call can sleep)
4415 * @set_tid_config: Apply TID specific configurations. This callback may sleep.
4416 * @reset_tid_config: Reset TID specific configuration for the peer.
4417 * This callback may sleep.
4418 * @update_vif_offload: Update virtual interface offload flags
4419 * This callback may sleep.
4420 * @sta_set_4addr: Called to notify the driver when a station starts/stops using
4421 * 4-address mode
4422 * @set_sar_specs: Update the SAR (TX power) settings.
4423 * @sta_set_decap_offload: Called to notify the driver when a station is allowed
4424 * to use rx decapsulation offload
4425 * @add_twt_setup: Update hw with TWT agreement parameters received from the peer.
4426 * This callback allows the hw to check if requested parameters
4427 * are supported and if there is enough room for a new agreement.
4428 * The hw is expected to set agreement result in the req_type field of
4429 * twt structure.
4430 * @twt_teardown_request: Update the hw with TWT teardown request received
4431 * from the peer.
4432 * @set_radar_background: Configure dedicated offchannel chain available for
4433 * radar/CAC detection on some hw. This chain can't be used to transmit
4434 * or receive frames and it is bounded to a running wdev.
4435 * Background radar/CAC detection allows to avoid the CAC downtime
4436 * switching to a different channel during CAC detection on the selected
4437 * radar channel.
4438 * The caller is expected to set chandef pointer to NULL in order to
4439 * disable background CAC/radar detection.
4440 * @net_fill_forward_path: Called from .ndo_fill_forward_path in order to
4441 * resolve a path for hardware flow offloading
4442 * @can_activate_links: Checks if a specific active_links bitmap is
4443 * supported by the driver.
4444 * @change_vif_links: Change the valid links on an interface, note that while
4445 * removing the old link information is still valid (link_conf pointer),
4446 * but may immediately disappear after the function returns. The old or
4447 * new links bitmaps may be 0 if going from/to a non-MLO situation.
4448 * The @old array contains pointers to the old bss_conf structures
4449 * that were already removed, in case they're needed.
4450 * This callback can sleep.
4451 * @change_sta_links: Change the valid links of a station, similar to
4452 * @change_vif_links. This callback can sleep.
4453 * Note that a sta can also be inserted or removed with valid links,
4454 * i.e. passed to @sta_add/@sta_state with sta->valid_links not zero.
4455 * In fact, cannot change from having valid_links and not having them.
4456 * @set_hw_timestamp: Enable/disable HW timestamping of TM/FTM frames. This is
4457 * not restored at HW reset by mac80211 so drivers need to take care of
4458 * that.
4459 * @net_setup_tc: Called from .ndo_setup_tc in order to prepare hardware
4460 * flow offloading for flows originating from the vif.
4461 * Note that the driver must not assume that the vif driver_data is valid
4462 * at this point, since the callback can be called during netdev teardown.
4463 * @can_neg_ttlm: for managed interface, requests the driver to determine
4464 * if the requested TID-To-Link mapping can be accepted or not.
4465 * If it's not accepted the driver may suggest a preferred mapping and
4466 * modify @ttlm parameter with the suggested TID-to-Link mapping.
4467 * @prep_add_interface: prepare for interface addition. This can be used by
4468 * drivers to prepare for the addition of a new interface, e.g., allocate
4469 * the needed resources etc. This callback doesn't guarantee that an
4470 * interface with the specified type would be added, and thus drivers that
4471 * implement this callback need to handle such cases. The type is the full
4472 * &enum nl80211_iftype.
4473 */
4474struct ieee80211_ops {
4475 void (*tx)(struct ieee80211_hw *hw,
4476 struct ieee80211_tx_control *control,
4477 struct sk_buff *skb);
4478 int (*start)(struct ieee80211_hw *hw);
4479 void (*stop)(struct ieee80211_hw *hw, bool suspend);
4480#ifdef CONFIG_PM
4481 int (*suspend)(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan);
4482 int (*resume)(struct ieee80211_hw *hw);
4483 void (*set_wakeup)(struct ieee80211_hw *hw, bool enabled);
4484#endif
4485 int (*add_interface)(struct ieee80211_hw *hw,
4486 struct ieee80211_vif *vif);
4487 int (*change_interface)(struct ieee80211_hw *hw,
4488 struct ieee80211_vif *vif,
4489 enum nl80211_iftype new_type, bool p2p);
4490 void (*remove_interface)(struct ieee80211_hw *hw,
4491 struct ieee80211_vif *vif);
4492 int (*config)(struct ieee80211_hw *hw, u32 changed);
4493 void (*bss_info_changed)(struct ieee80211_hw *hw,
4494 struct ieee80211_vif *vif,
4495 struct ieee80211_bss_conf *info,
4496 u64 changed);
4497 void (*vif_cfg_changed)(struct ieee80211_hw *hw,
4498 struct ieee80211_vif *vif,
4499 u64 changed);
4500 void (*link_info_changed)(struct ieee80211_hw *hw,
4501 struct ieee80211_vif *vif,
4502 struct ieee80211_bss_conf *info,
4503 u64 changed);
4504
4505 int (*start_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4506 struct ieee80211_bss_conf *link_conf);
4507 void (*stop_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4508 struct ieee80211_bss_conf *link_conf);
4509
4510 u64 (*prepare_multicast)(struct ieee80211_hw *hw,
4511 struct netdev_hw_addr_list *mc_list);
4512 void (*configure_filter)(struct ieee80211_hw *hw,
4513 unsigned int changed_flags,
4514 unsigned int *total_flags,
4515 u64 multicast);
4516 void (*config_iface_filter)(struct ieee80211_hw *hw,
4517 struct ieee80211_vif *vif,
4518 unsigned int filter_flags,
4519 unsigned int changed_flags);
4520 int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
4521 bool set);
4522 int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd,
4523 struct ieee80211_vif *vif, struct ieee80211_sta *sta,
4524 struct ieee80211_key_conf *key);
4525 void (*update_tkip_key)(struct ieee80211_hw *hw,
4526 struct ieee80211_vif *vif,
4527 struct ieee80211_key_conf *conf,
4528 struct ieee80211_sta *sta,
4529 u32 iv32, u16 *phase1key);
4530 void (*set_rekey_data)(struct ieee80211_hw *hw,
4531 struct ieee80211_vif *vif,
4532 struct cfg80211_gtk_rekey_data *data);
4533 void (*set_default_unicast_key)(struct ieee80211_hw *hw,
4534 struct ieee80211_vif *vif, int idx);
4535 int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4536 struct ieee80211_scan_request *req);
4537 void (*cancel_hw_scan)(struct ieee80211_hw *hw,
4538 struct ieee80211_vif *vif);
4539 int (*sched_scan_start)(struct ieee80211_hw *hw,
4540 struct ieee80211_vif *vif,
4541 struct cfg80211_sched_scan_request *req,
4542 struct ieee80211_scan_ies *ies);
4543 int (*sched_scan_stop)(struct ieee80211_hw *hw,
4544 struct ieee80211_vif *vif);
4545 void (*sw_scan_start)(struct ieee80211_hw *hw,
4546 struct ieee80211_vif *vif,
4547 const u8 *mac_addr);
4548 void (*sw_scan_complete)(struct ieee80211_hw *hw,
4549 struct ieee80211_vif *vif);
4550 int (*get_stats)(struct ieee80211_hw *hw,
4551 struct ieee80211_low_level_stats *stats);
4552 void (*get_key_seq)(struct ieee80211_hw *hw,
4553 struct ieee80211_key_conf *key,
4554 struct ieee80211_key_seq *seq);
4555 int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);
4556 int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
4557 int (*sta_add)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4558 struct ieee80211_sta *sta);
4559 int (*sta_remove)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4560 struct ieee80211_sta *sta);
4561#ifdef CONFIG_MAC80211_DEBUGFS
4562 void (*vif_add_debugfs)(struct ieee80211_hw *hw,
4563 struct ieee80211_vif *vif);
4564 void (*link_add_debugfs)(struct ieee80211_hw *hw,
4565 struct ieee80211_vif *vif,
4566 struct ieee80211_bss_conf *link_conf,
4567 struct dentry *dir);
4568 void (*sta_add_debugfs)(struct ieee80211_hw *hw,
4569 struct ieee80211_vif *vif,
4570 struct ieee80211_sta *sta,
4571 struct dentry *dir);
4572 void (*link_sta_add_debugfs)(struct ieee80211_hw *hw,
4573 struct ieee80211_vif *vif,
4574 struct ieee80211_link_sta *link_sta,
4575 struct dentry *dir);
4576#endif
4577 void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4578 enum sta_notify_cmd, struct ieee80211_sta *sta);
4579 int (*sta_set_txpwr)(struct ieee80211_hw *hw,
4580 struct ieee80211_vif *vif,
4581 struct ieee80211_sta *sta);
4582 int (*sta_state)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4583 struct ieee80211_sta *sta,
4584 enum ieee80211_sta_state old_state,
4585 enum ieee80211_sta_state new_state);
4586 void (*sta_pre_rcu_remove)(struct ieee80211_hw *hw,
4587 struct ieee80211_vif *vif,
4588 struct ieee80211_sta *sta);
4589 void (*link_sta_rc_update)(struct ieee80211_hw *hw,
4590 struct ieee80211_vif *vif,
4591 struct ieee80211_link_sta *link_sta,
4592 u32 changed);
4593 void (*sta_rate_tbl_update)(struct ieee80211_hw *hw,
4594 struct ieee80211_vif *vif,
4595 struct ieee80211_sta *sta);
4596 void (*sta_statistics)(struct ieee80211_hw *hw,
4597 struct ieee80211_vif *vif,
4598 struct ieee80211_sta *sta,
4599 struct station_info *sinfo);
4600 int (*conf_tx)(struct ieee80211_hw *hw,
4601 struct ieee80211_vif *vif,
4602 unsigned int link_id, u16 ac,
4603 const struct ieee80211_tx_queue_params *params);
4604 u64 (*get_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
4605 void (*set_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4606 u64 tsf);
4607 void (*offset_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4608 s64 offset);
4609 void (*reset_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
4610 int (*tx_last_beacon)(struct ieee80211_hw *hw);
4611
4612 /**
4613 * @ampdu_action:
4614 * Perform a certain A-MPDU action.
4615 * The RA/TID combination determines the destination and TID we want
4616 * the ampdu action to be performed for. The action is defined through
4617 * ieee80211_ampdu_mlme_action.
4618 * When the action is set to %IEEE80211_AMPDU_TX_OPERATIONAL the driver
4619 * may neither send aggregates containing more subframes than @buf_size
4620 * nor send aggregates in a way that lost frames would exceed the
4621 * buffer size. If just limiting the aggregate size, this would be
4622 * possible with a buf_size of 8:
4623 *
4624 * - ``TX: 1.....7``
4625 * - ``RX: 2....7`` (lost frame #1)
4626 * - ``TX: 8..1...``
4627 *
4628 * which is invalid since #1 was now re-transmitted well past the
4629 * buffer size of 8. Correct ways to retransmit #1 would be:
4630 *
4631 * - ``TX: 1 or``
4632 * - ``TX: 18 or``
4633 * - ``TX: 81``
4634 *
4635 * Even ``189`` would be wrong since 1 could be lost again.
4636 *
4637 * Returns a negative error code on failure. The driver may return
4638 * %IEEE80211_AMPDU_TX_START_IMMEDIATE for %IEEE80211_AMPDU_TX_START
4639 * if the session can start immediately.
4640 *
4641 * The callback can sleep.
4642 */
4643 int (*ampdu_action)(struct ieee80211_hw *hw,
4644 struct ieee80211_vif *vif,
4645 struct ieee80211_ampdu_params *params);
4646 int (*get_survey)(struct ieee80211_hw *hw, int idx,
4647 struct survey_info *survey);
4648 void (*rfkill_poll)(struct ieee80211_hw *hw);
4649 void (*set_coverage_class)(struct ieee80211_hw *hw, s16 coverage_class);
4650#ifdef CONFIG_NL80211_TESTMODE
4651 int (*testmode_cmd)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4652 void *data, int len);
4653 int (*testmode_dump)(struct ieee80211_hw *hw, struct sk_buff *skb,
4654 struct netlink_callback *cb,
4655 void *data, int len);
4656#endif
4657 void (*flush)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4658 u32 queues, bool drop);
4659 void (*flush_sta)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4660 struct ieee80211_sta *sta);
4661 void (*channel_switch)(struct ieee80211_hw *hw,
4662 struct ieee80211_vif *vif,
4663 struct ieee80211_channel_switch *ch_switch);
4664 int (*set_antenna)(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant);
4665 int (*get_antenna)(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant);
4666
4667 int (*remain_on_channel)(struct ieee80211_hw *hw,
4668 struct ieee80211_vif *vif,
4669 struct ieee80211_channel *chan,
4670 int duration,
4671 enum ieee80211_roc_type type);
4672 int (*cancel_remain_on_channel)(struct ieee80211_hw *hw,
4673 struct ieee80211_vif *vif);
4674 int (*set_ringparam)(struct ieee80211_hw *hw, u32 tx, u32 rx);
4675 void (*get_ringparam)(struct ieee80211_hw *hw,
4676 u32 *tx, u32 *tx_max, u32 *rx, u32 *rx_max);
4677 bool (*tx_frames_pending)(struct ieee80211_hw *hw);
4678 int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4679 const struct cfg80211_bitrate_mask *mask);
4680 void (*event_callback)(struct ieee80211_hw *hw,
4681 struct ieee80211_vif *vif,
4682 const struct ieee80211_event *event);
4683
4684 void (*allow_buffered_frames)(struct ieee80211_hw *hw,
4685 struct ieee80211_sta *sta,
4686 u16 tids, int num_frames,
4687 enum ieee80211_frame_release_type reason,
4688 bool more_data);
4689 void (*release_buffered_frames)(struct ieee80211_hw *hw,
4690 struct ieee80211_sta *sta,
4691 u16 tids, int num_frames,
4692 enum ieee80211_frame_release_type reason,
4693 bool more_data);
4694
4695 int (*get_et_sset_count)(struct ieee80211_hw *hw,
4696 struct ieee80211_vif *vif, int sset);
4697 void (*get_et_stats)(struct ieee80211_hw *hw,
4698 struct ieee80211_vif *vif,
4699 struct ethtool_stats *stats, u64 *data);
4700 void (*get_et_strings)(struct ieee80211_hw *hw,
4701 struct ieee80211_vif *vif,
4702 u32 sset, u8 *data);
4703
4704 void (*mgd_prepare_tx)(struct ieee80211_hw *hw,
4705 struct ieee80211_vif *vif,
4706 struct ieee80211_prep_tx_info *info);
4707 void (*mgd_complete_tx)(struct ieee80211_hw *hw,
4708 struct ieee80211_vif *vif,
4709 struct ieee80211_prep_tx_info *info);
4710
4711 void (*mgd_protect_tdls_discover)(struct ieee80211_hw *hw,
4712 struct ieee80211_vif *vif,
4713 unsigned int link_id);
4714
4715 int (*add_chanctx)(struct ieee80211_hw *hw,
4716 struct ieee80211_chanctx_conf *ctx);
4717 void (*remove_chanctx)(struct ieee80211_hw *hw,
4718 struct ieee80211_chanctx_conf *ctx);
4719 void (*change_chanctx)(struct ieee80211_hw *hw,
4720 struct ieee80211_chanctx_conf *ctx,
4721 u32 changed);
4722 int (*assign_vif_chanctx)(struct ieee80211_hw *hw,
4723 struct ieee80211_vif *vif,
4724 struct ieee80211_bss_conf *link_conf,
4725 struct ieee80211_chanctx_conf *ctx);
4726 void (*unassign_vif_chanctx)(struct ieee80211_hw *hw,
4727 struct ieee80211_vif *vif,
4728 struct ieee80211_bss_conf *link_conf,
4729 struct ieee80211_chanctx_conf *ctx);
4730 int (*switch_vif_chanctx)(struct ieee80211_hw *hw,
4731 struct ieee80211_vif_chanctx_switch *vifs,
4732 int n_vifs,
4733 enum ieee80211_chanctx_switch_mode mode);
4734
4735 void (*reconfig_complete)(struct ieee80211_hw *hw,
4736 enum ieee80211_reconfig_type reconfig_type);
4737
4738#if IS_ENABLED(CONFIG_IPV6)
4739 void (*ipv6_addr_change)(struct ieee80211_hw *hw,
4740 struct ieee80211_vif *vif,
4741 struct inet6_dev *idev);
4742#endif
4743 void (*channel_switch_beacon)(struct ieee80211_hw *hw,
4744 struct ieee80211_vif *vif,
4745 struct cfg80211_chan_def *chandef);
4746 int (*pre_channel_switch)(struct ieee80211_hw *hw,
4747 struct ieee80211_vif *vif,
4748 struct ieee80211_channel_switch *ch_switch);
4749
4750 int (*post_channel_switch)(struct ieee80211_hw *hw,
4751 struct ieee80211_vif *vif,
4752 struct ieee80211_bss_conf *link_conf);
4753 void (*abort_channel_switch)(struct ieee80211_hw *hw,
4754 struct ieee80211_vif *vif,
4755 struct ieee80211_bss_conf *link_conf);
4756 void (*channel_switch_rx_beacon)(struct ieee80211_hw *hw,
4757 struct ieee80211_vif *vif,
4758 struct ieee80211_channel_switch *ch_switch);
4759
4760 int (*join_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
4761 void (*leave_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
4762 u32 (*get_expected_throughput)(struct ieee80211_hw *hw,
4763 struct ieee80211_sta *sta);
4764 int (*get_txpower)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4765 int *dbm);
4766
4767 int (*tdls_channel_switch)(struct ieee80211_hw *hw,
4768 struct ieee80211_vif *vif,
4769 struct ieee80211_sta *sta, u8 oper_class,
4770 struct cfg80211_chan_def *chandef,
4771 struct sk_buff *tmpl_skb, u32 ch_sw_tm_ie);
4772 void (*tdls_cancel_channel_switch)(struct ieee80211_hw *hw,
4773 struct ieee80211_vif *vif,
4774 struct ieee80211_sta *sta);
4775 void (*tdls_recv_channel_switch)(struct ieee80211_hw *hw,
4776 struct ieee80211_vif *vif,
4777 struct ieee80211_tdls_ch_sw_params *params);
4778
4779 void (*wake_tx_queue)(struct ieee80211_hw *hw,
4780 struct ieee80211_txq *txq);
4781 void (*sync_rx_queues)(struct ieee80211_hw *hw);
4782
4783 int (*start_nan)(struct ieee80211_hw *hw,
4784 struct ieee80211_vif *vif,
4785 struct cfg80211_nan_conf *conf);
4786 int (*stop_nan)(struct ieee80211_hw *hw,
4787 struct ieee80211_vif *vif);
4788 int (*nan_change_conf)(struct ieee80211_hw *hw,
4789 struct ieee80211_vif *vif,
4790 struct cfg80211_nan_conf *conf, u32 changes);
4791 int (*add_nan_func)(struct ieee80211_hw *hw,
4792 struct ieee80211_vif *vif,
4793 const struct cfg80211_nan_func *nan_func);
4794 void (*del_nan_func)(struct ieee80211_hw *hw,
4795 struct ieee80211_vif *vif,
4796 u8 instance_id);
4797 bool (*can_aggregate_in_amsdu)(struct ieee80211_hw *hw,
4798 struct sk_buff *head,
4799 struct sk_buff *skb);
4800 int (*get_ftm_responder_stats)(struct ieee80211_hw *hw,
4801 struct ieee80211_vif *vif,
4802 struct cfg80211_ftm_responder_stats *ftm_stats);
4803 int (*start_pmsr)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4804 struct cfg80211_pmsr_request *request);
4805 void (*abort_pmsr)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4806 struct cfg80211_pmsr_request *request);
4807 int (*set_tid_config)(struct ieee80211_hw *hw,
4808 struct ieee80211_vif *vif,
4809 struct ieee80211_sta *sta,
4810 struct cfg80211_tid_config *tid_conf);
4811 int (*reset_tid_config)(struct ieee80211_hw *hw,
4812 struct ieee80211_vif *vif,
4813 struct ieee80211_sta *sta, u8 tids);
4814 void (*update_vif_offload)(struct ieee80211_hw *hw,
4815 struct ieee80211_vif *vif);
4816 void (*sta_set_4addr)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4817 struct ieee80211_sta *sta, bool enabled);
4818 int (*set_sar_specs)(struct ieee80211_hw *hw,
4819 const struct cfg80211_sar_specs *sar);
4820 void (*sta_set_decap_offload)(struct ieee80211_hw *hw,
4821 struct ieee80211_vif *vif,
4822 struct ieee80211_sta *sta, bool enabled);
4823 void (*add_twt_setup)(struct ieee80211_hw *hw,
4824 struct ieee80211_sta *sta,
4825 struct ieee80211_twt_setup *twt);
4826 void (*twt_teardown_request)(struct ieee80211_hw *hw,
4827 struct ieee80211_sta *sta, u8 flowid);
4828 int (*set_radar_background)(struct ieee80211_hw *hw,
4829 struct cfg80211_chan_def *chandef);
4830 int (*net_fill_forward_path)(struct ieee80211_hw *hw,
4831 struct ieee80211_vif *vif,
4832 struct ieee80211_sta *sta,
4833 struct net_device_path_ctx *ctx,
4834 struct net_device_path *path);
4835 bool (*can_activate_links)(struct ieee80211_hw *hw,
4836 struct ieee80211_vif *vif,
4837 u16 active_links);
4838 int (*change_vif_links)(struct ieee80211_hw *hw,
4839 struct ieee80211_vif *vif,
4840 u16 old_links, u16 new_links,
4841 struct ieee80211_bss_conf *old[IEEE80211_MLD_MAX_NUM_LINKS]);
4842 int (*change_sta_links)(struct ieee80211_hw *hw,
4843 struct ieee80211_vif *vif,
4844 struct ieee80211_sta *sta,
4845 u16 old_links, u16 new_links);
4846 int (*set_hw_timestamp)(struct ieee80211_hw *hw,
4847 struct ieee80211_vif *vif,
4848 struct cfg80211_set_hw_timestamp *hwts);
4849 int (*net_setup_tc)(struct ieee80211_hw *hw,
4850 struct ieee80211_vif *vif,
4851 struct net_device *dev,
4852 enum tc_setup_type type,
4853 void *type_data);
4854 enum ieee80211_neg_ttlm_res
4855 (*can_neg_ttlm)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4856 struct ieee80211_neg_ttlm *ttlm);
4857 void (*prep_add_interface)(struct ieee80211_hw *hw,
4858 enum nl80211_iftype type);
4859};
4860
4861/**
4862 * ieee80211_alloc_hw_nm - Allocate a new hardware device
4863 *
4864 * This must be called once for each hardware device. The returned pointer
4865 * must be used to refer to this device when calling other functions.
4866 * mac80211 allocates a private data area for the driver pointed to by
4867 * @priv in &struct ieee80211_hw, the size of this area is given as
4868 * @priv_data_len.
4869 *
4870 * @priv_data_len: length of private data
4871 * @ops: callbacks for this device
4872 * @requested_name: Requested name for this device.
4873 * NULL is valid value, and means use the default naming (phy%d)
4874 *
4875 * Return: A pointer to the new hardware device, or %NULL on error.
4876 */
4877struct ieee80211_hw *ieee80211_alloc_hw_nm(size_t priv_data_len,
4878 const struct ieee80211_ops *ops,
4879 const char *requested_name);
4880
4881/**
4882 * ieee80211_alloc_hw - Allocate a new hardware device
4883 *
4884 * This must be called once for each hardware device. The returned pointer
4885 * must be used to refer to this device when calling other functions.
4886 * mac80211 allocates a private data area for the driver pointed to by
4887 * @priv in &struct ieee80211_hw, the size of this area is given as
4888 * @priv_data_len.
4889 *
4890 * @priv_data_len: length of private data
4891 * @ops: callbacks for this device
4892 *
4893 * Return: A pointer to the new hardware device, or %NULL on error.
4894 */
4895static inline
4896struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len,
4897 const struct ieee80211_ops *ops)
4898{
4899 return ieee80211_alloc_hw_nm(priv_data_len, ops, NULL);
4900}
4901
4902/**
4903 * ieee80211_register_hw - Register hardware device
4904 *
4905 * You must call this function before any other functions in
4906 * mac80211. Note that before a hardware can be registered, you
4907 * need to fill the contained wiphy's information.
4908 *
4909 * @hw: the device to register as returned by ieee80211_alloc_hw()
4910 *
4911 * Return: 0 on success. An error code otherwise.
4912 */
4913int ieee80211_register_hw(struct ieee80211_hw *hw);
4914
4915/**
4916 * struct ieee80211_tpt_blink - throughput blink description
4917 * @throughput: throughput in Kbit/sec
4918 * @blink_time: blink time in milliseconds
4919 * (full cycle, ie. one off + one on period)
4920 */
4921struct ieee80211_tpt_blink {
4922 int throughput;
4923 int blink_time;
4924};
4925
4926/**
4927 * enum ieee80211_tpt_led_trigger_flags - throughput trigger flags
4928 * @IEEE80211_TPT_LEDTRIG_FL_RADIO: enable blinking with radio
4929 * @IEEE80211_TPT_LEDTRIG_FL_WORK: enable blinking when working
4930 * @IEEE80211_TPT_LEDTRIG_FL_CONNECTED: enable blinking when at least one
4931 * interface is connected in some way, including being an AP
4932 */
4933enum ieee80211_tpt_led_trigger_flags {
4934 IEEE80211_TPT_LEDTRIG_FL_RADIO = BIT(0),
4935 IEEE80211_TPT_LEDTRIG_FL_WORK = BIT(1),
4936 IEEE80211_TPT_LEDTRIG_FL_CONNECTED = BIT(2),
4937};
4938
4939#ifdef CONFIG_MAC80211_LEDS
4940const char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
4941const char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
4942const char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
4943const char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
4944const char *
4945__ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw,
4946 unsigned int flags,
4947 const struct ieee80211_tpt_blink *blink_table,
4948 unsigned int blink_table_len);
4949#endif
4950/**
4951 * ieee80211_get_tx_led_name - get name of TX LED
4952 *
4953 * mac80211 creates a transmit LED trigger for each wireless hardware
4954 * that can be used to drive LEDs if your driver registers a LED device.
4955 * This function returns the name (or %NULL if not configured for LEDs)
4956 * of the trigger so you can automatically link the LED device.
4957 *
4958 * @hw: the hardware to get the LED trigger name for
4959 *
4960 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
4961 */
4962static inline const char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw)
4963{
4964#ifdef CONFIG_MAC80211_LEDS
4965 return __ieee80211_get_tx_led_name(hw);
4966#else
4967 return NULL;
4968#endif
4969}
4970
4971/**
4972 * ieee80211_get_rx_led_name - get name of RX LED
4973 *
4974 * mac80211 creates a receive LED trigger for each wireless hardware
4975 * that can be used to drive LEDs if your driver registers a LED device.
4976 * This function returns the name (or %NULL if not configured for LEDs)
4977 * of the trigger so you can automatically link the LED device.
4978 *
4979 * @hw: the hardware to get the LED trigger name for
4980 *
4981 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
4982 */
4983static inline const char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw)
4984{
4985#ifdef CONFIG_MAC80211_LEDS
4986 return __ieee80211_get_rx_led_name(hw);
4987#else
4988 return NULL;
4989#endif
4990}
4991
4992/**
4993 * ieee80211_get_assoc_led_name - get name of association LED
4994 *
4995 * mac80211 creates a association LED trigger for each wireless hardware
4996 * that can be used to drive LEDs if your driver registers a LED device.
4997 * This function returns the name (or %NULL if not configured for LEDs)
4998 * of the trigger so you can automatically link the LED device.
4999 *
5000 * @hw: the hardware to get the LED trigger name for
5001 *
5002 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
5003 */
5004static inline const char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
5005{
5006#ifdef CONFIG_MAC80211_LEDS
5007 return __ieee80211_get_assoc_led_name(hw);
5008#else
5009 return NULL;
5010#endif
5011}
5012
5013/**
5014 * ieee80211_get_radio_led_name - get name of radio LED
5015 *
5016 * mac80211 creates a radio change LED trigger for each wireless hardware
5017 * that can be used to drive LEDs if your driver registers a LED device.
5018 * This function returns the name (or %NULL if not configured for LEDs)
5019 * of the trigger so you can automatically link the LED device.
5020 *
5021 * @hw: the hardware to get the LED trigger name for
5022 *
5023 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
5024 */
5025static inline const char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw)
5026{
5027#ifdef CONFIG_MAC80211_LEDS
5028 return __ieee80211_get_radio_led_name(hw);
5029#else
5030 return NULL;
5031#endif
5032}
5033
5034/**
5035 * ieee80211_create_tpt_led_trigger - create throughput LED trigger
5036 * @hw: the hardware to create the trigger for
5037 * @flags: trigger flags, see &enum ieee80211_tpt_led_trigger_flags
5038 * @blink_table: the blink table -- needs to be ordered by throughput
5039 * @blink_table_len: size of the blink table
5040 *
5041 * Return: %NULL (in case of error, or if no LED triggers are
5042 * configured) or the name of the new trigger.
5043 *
5044 * Note: This function must be called before ieee80211_register_hw().
5045 */
5046static inline const char *
5047ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, unsigned int flags,
5048 const struct ieee80211_tpt_blink *blink_table,
5049 unsigned int blink_table_len)
5050{
5051#ifdef CONFIG_MAC80211_LEDS
5052 return __ieee80211_create_tpt_led_trigger(hw, flags, blink_table,
5053 blink_table_len);
5054#else
5055 return NULL;
5056#endif
5057}
5058
5059/**
5060 * ieee80211_unregister_hw - Unregister a hardware device
5061 *
5062 * This function instructs mac80211 to free allocated resources
5063 * and unregister netdevices from the networking subsystem.
5064 *
5065 * @hw: the hardware to unregister
5066 */
5067void ieee80211_unregister_hw(struct ieee80211_hw *hw);
5068
5069/**
5070 * ieee80211_free_hw - free hardware descriptor
5071 *
5072 * This function frees everything that was allocated, including the
5073 * private data for the driver. You must call ieee80211_unregister_hw()
5074 * before calling this function.
5075 *
5076 * @hw: the hardware to free
5077 */
5078void ieee80211_free_hw(struct ieee80211_hw *hw);
5079
5080/**
5081 * ieee80211_restart_hw - restart hardware completely
5082 *
5083 * Call this function when the hardware was restarted for some reason
5084 * (hardware error, ...) and the driver is unable to restore its state
5085 * by itself. mac80211 assumes that at this point the driver/hardware
5086 * is completely uninitialised and stopped, it starts the process by
5087 * calling the ->start() operation. The driver will need to reset all
5088 * internal state that it has prior to calling this function.
5089 *
5090 * @hw: the hardware to restart
5091 */
5092void ieee80211_restart_hw(struct ieee80211_hw *hw);
5093
5094/**
5095 * ieee80211_rx_list - receive frame and store processed skbs in a list
5096 *
5097 * Use this function to hand received frames to mac80211. The receive
5098 * buffer in @skb must start with an IEEE 802.11 header. In case of a
5099 * paged @skb is used, the driver is recommended to put the ieee80211
5100 * header of the frame on the linear part of the @skb to avoid memory
5101 * allocation and/or memcpy by the stack.
5102 *
5103 * This function may not be called in IRQ context. Calls to this function
5104 * for a single hardware must be synchronized against each other. Calls to
5105 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
5106 * mixed for a single hardware. Must not run concurrently with
5107 * ieee80211_tx_status_skb() or ieee80211_tx_status_ni().
5108 *
5109 * This function must be called with BHs disabled and RCU read lock
5110 *
5111 * @hw: the hardware this frame came in on
5112 * @sta: the station the frame was received from, or %NULL
5113 * @skb: the buffer to receive, owned by mac80211 after this call
5114 * @list: the destination list
5115 */
5116void ieee80211_rx_list(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
5117 struct sk_buff *skb, struct list_head *list);
5118
5119/**
5120 * ieee80211_rx_napi - receive frame from NAPI context
5121 *
5122 * Use this function to hand received frames to mac80211. The receive
5123 * buffer in @skb must start with an IEEE 802.11 header. In case of a
5124 * paged @skb is used, the driver is recommended to put the ieee80211
5125 * header of the frame on the linear part of the @skb to avoid memory
5126 * allocation and/or memcpy by the stack.
5127 *
5128 * This function may not be called in IRQ context. Calls to this function
5129 * for a single hardware must be synchronized against each other. Calls to
5130 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
5131 * mixed for a single hardware. Must not run concurrently with
5132 * ieee80211_tx_status_skb() or ieee80211_tx_status_ni().
5133 *
5134 * This function must be called with BHs disabled.
5135 *
5136 * @hw: the hardware this frame came in on
5137 * @sta: the station the frame was received from, or %NULL
5138 * @skb: the buffer to receive, owned by mac80211 after this call
5139 * @napi: the NAPI context
5140 */
5141void ieee80211_rx_napi(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
5142 struct sk_buff *skb, struct napi_struct *napi);
5143
5144/**
5145 * ieee80211_rx - receive frame
5146 *
5147 * Use this function to hand received frames to mac80211. The receive
5148 * buffer in @skb must start with an IEEE 802.11 header. In case of a
5149 * paged @skb is used, the driver is recommended to put the ieee80211
5150 * header of the frame on the linear part of the @skb to avoid memory
5151 * allocation and/or memcpy by the stack.
5152 *
5153 * This function may not be called in IRQ context. Calls to this function
5154 * for a single hardware must be synchronized against each other. Calls to
5155 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
5156 * mixed for a single hardware. Must not run concurrently with
5157 * ieee80211_tx_status_skb() or ieee80211_tx_status_ni().
5158 *
5159 * In process context use instead ieee80211_rx_ni().
5160 *
5161 * @hw: the hardware this frame came in on
5162 * @skb: the buffer to receive, owned by mac80211 after this call
5163 */
5164static inline void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb)
5165{
5166 ieee80211_rx_napi(hw, NULL, skb, NULL);
5167}
5168
5169/**
5170 * ieee80211_rx_irqsafe - receive frame
5171 *
5172 * Like ieee80211_rx() but can be called in IRQ context
5173 * (internally defers to a tasklet.)
5174 *
5175 * Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not
5176 * be mixed for a single hardware.Must not run concurrently with
5177 * ieee80211_tx_status_skb() or ieee80211_tx_status_ni().
5178 *
5179 * @hw: the hardware this frame came in on
5180 * @skb: the buffer to receive, owned by mac80211 after this call
5181 */
5182void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb);
5183
5184/**
5185 * ieee80211_rx_ni - receive frame (in process context)
5186 *
5187 * Like ieee80211_rx() but can be called in process context
5188 * (internally disables bottom halves).
5189 *
5190 * Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may
5191 * not be mixed for a single hardware. Must not run concurrently with
5192 * ieee80211_tx_status_skb() or ieee80211_tx_status_ni().
5193 *
5194 * @hw: the hardware this frame came in on
5195 * @skb: the buffer to receive, owned by mac80211 after this call
5196 */
5197static inline void ieee80211_rx_ni(struct ieee80211_hw *hw,
5198 struct sk_buff *skb)
5199{
5200 local_bh_disable();
5201 ieee80211_rx(hw, skb);
5202 local_bh_enable();
5203}
5204
5205/**
5206 * ieee80211_sta_ps_transition - PS transition for connected sta
5207 *
5208 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS
5209 * flag set, use this function to inform mac80211 about a connected station
5210 * entering/leaving PS mode.
5211 *
5212 * This function may not be called in IRQ context or with softirqs enabled.
5213 *
5214 * Calls to this function for a single hardware must be synchronized against
5215 * each other.
5216 *
5217 * @sta: currently connected sta
5218 * @start: start or stop PS
5219 *
5220 * Return: 0 on success. -EINVAL when the requested PS mode is already set.
5221 */
5222int ieee80211_sta_ps_transition(struct ieee80211_sta *sta, bool start);
5223
5224/**
5225 * ieee80211_sta_ps_transition_ni - PS transition for connected sta
5226 * (in process context)
5227 *
5228 * Like ieee80211_sta_ps_transition() but can be called in process context
5229 * (internally disables bottom halves). Concurrent call restriction still
5230 * applies.
5231 *
5232 * @sta: currently connected sta
5233 * @start: start or stop PS
5234 *
5235 * Return: Like ieee80211_sta_ps_transition().
5236 */
5237static inline int ieee80211_sta_ps_transition_ni(struct ieee80211_sta *sta,
5238 bool start)
5239{
5240 int ret;
5241
5242 local_bh_disable();
5243 ret = ieee80211_sta_ps_transition(sta, start);
5244 local_bh_enable();
5245
5246 return ret;
5247}
5248
5249/**
5250 * ieee80211_sta_pspoll - PS-Poll frame received
5251 * @sta: currently connected station
5252 *
5253 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS flag set,
5254 * use this function to inform mac80211 that a PS-Poll frame from a
5255 * connected station was received.
5256 * This must be used in conjunction with ieee80211_sta_ps_transition()
5257 * and possibly ieee80211_sta_uapsd_trigger(); calls to all three must
5258 * be serialized.
5259 */
5260void ieee80211_sta_pspoll(struct ieee80211_sta *sta);
5261
5262/**
5263 * ieee80211_sta_uapsd_trigger - (potential) U-APSD trigger frame received
5264 * @sta: currently connected station
5265 * @tid: TID of the received (potential) trigger frame
5266 *
5267 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS flag set,
5268 * use this function to inform mac80211 that a (potential) trigger frame
5269 * from a connected station was received.
5270 * This must be used in conjunction with ieee80211_sta_ps_transition()
5271 * and possibly ieee80211_sta_pspoll(); calls to all three must be
5272 * serialized.
5273 * %IEEE80211_NUM_TIDS can be passed as the tid if the tid is unknown.
5274 * In this case, mac80211 will not check that this tid maps to an AC
5275 * that is trigger enabled and assume that the caller did the proper
5276 * checks.
5277 */
5278void ieee80211_sta_uapsd_trigger(struct ieee80211_sta *sta, u8 tid);
5279
5280/*
5281 * The TX headroom reserved by mac80211 for its own tx_status functions.
5282 * This is enough for the radiotap header.
5283 */
5284#define IEEE80211_TX_STATUS_HEADROOM ALIGN(14, 4)
5285
5286/**
5287 * ieee80211_sta_set_buffered - inform mac80211 about driver-buffered frames
5288 * @sta: &struct ieee80211_sta pointer for the sleeping station
5289 * @tid: the TID that has buffered frames
5290 * @buffered: indicates whether or not frames are buffered for this TID
5291 *
5292 * If a driver buffers frames for a powersave station instead of passing
5293 * them back to mac80211 for retransmission, the station may still need
5294 * to be told that there are buffered frames via the TIM bit.
5295 *
5296 * This function informs mac80211 whether or not there are frames that are
5297 * buffered in the driver for a given TID; mac80211 can then use this data
5298 * to set the TIM bit (NOTE: This may call back into the driver's set_tim
5299 * call! Beware of the locking!)
5300 *
5301 * If all frames are released to the station (due to PS-poll or uAPSD)
5302 * then the driver needs to inform mac80211 that there no longer are
5303 * frames buffered. However, when the station wakes up mac80211 assumes
5304 * that all buffered frames will be transmitted and clears this data,
5305 * drivers need to make sure they inform mac80211 about all buffered
5306 * frames on the sleep transition (sta_notify() with %STA_NOTIFY_SLEEP).
5307 *
5308 * Note that technically mac80211 only needs to know this per AC, not per
5309 * TID, but since driver buffering will inevitably happen per TID (since
5310 * it is related to aggregation) it is easier to make mac80211 map the
5311 * TID to the AC as required instead of keeping track in all drivers that
5312 * use this API.
5313 */
5314void ieee80211_sta_set_buffered(struct ieee80211_sta *sta,
5315 u8 tid, bool buffered);
5316
5317/**
5318 * ieee80211_get_tx_rates - get the selected transmit rates for a packet
5319 *
5320 * Call this function in a driver with per-packet rate selection support
5321 * to combine the rate info in the packet tx info with the most recent
5322 * rate selection table for the station entry.
5323 *
5324 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5325 * @sta: the receiver station to which this packet is sent.
5326 * @skb: the frame to be transmitted.
5327 * @dest: buffer for extracted rate/retry information
5328 * @max_rates: maximum number of rates to fetch
5329 */
5330void ieee80211_get_tx_rates(struct ieee80211_vif *vif,
5331 struct ieee80211_sta *sta,
5332 struct sk_buff *skb,
5333 struct ieee80211_tx_rate *dest,
5334 int max_rates);
5335
5336/**
5337 * ieee80211_sta_set_expected_throughput - set the expected tpt for a station
5338 *
5339 * Call this function to notify mac80211 about a change in expected throughput
5340 * to a station. A driver for a device that does rate control in firmware can
5341 * call this function when the expected throughput estimate towards a station
5342 * changes. The information is used to tune the CoDel AQM applied to traffic
5343 * going towards that station (which can otherwise be too aggressive and cause
5344 * slow stations to starve).
5345 *
5346 * @pubsta: the station to set throughput for.
5347 * @thr: the current expected throughput in kbps.
5348 */
5349void ieee80211_sta_set_expected_throughput(struct ieee80211_sta *pubsta,
5350 u32 thr);
5351
5352/**
5353 * ieee80211_tx_rate_update - transmit rate update callback
5354 *
5355 * Drivers should call this functions with a non-NULL pub sta
5356 * This function can be used in drivers that does not have provision
5357 * in updating the tx rate in data path.
5358 *
5359 * @hw: the hardware the frame was transmitted by
5360 * @pubsta: the station to update the tx rate for.
5361 * @info: tx status information
5362 */
5363void ieee80211_tx_rate_update(struct ieee80211_hw *hw,
5364 struct ieee80211_sta *pubsta,
5365 struct ieee80211_tx_info *info);
5366
5367/**
5368 * ieee80211_tx_status_skb - transmit status callback
5369 *
5370 * Call this function for all transmitted frames after they have been
5371 * transmitted. It is permissible to not call this function for
5372 * multicast frames but this can affect statistics.
5373 *
5374 * This function may not be called in IRQ context. Calls to this function
5375 * for a single hardware must be synchronized against each other. Calls
5376 * to this function, ieee80211_tx_status_ni() and ieee80211_tx_status_irqsafe()
5377 * may not be mixed for a single hardware. Must not run concurrently with
5378 * ieee80211_rx() or ieee80211_rx_ni().
5379 *
5380 * @hw: the hardware the frame was transmitted by
5381 * @skb: the frame that was transmitted, owned by mac80211 after this call
5382 */
5383void ieee80211_tx_status_skb(struct ieee80211_hw *hw,
5384 struct sk_buff *skb);
5385
5386/**
5387 * ieee80211_tx_status_ext - extended transmit status callback
5388 *
5389 * This function can be used as a replacement for ieee80211_tx_status_skb()
5390 * in drivers that may want to provide extra information that does not
5391 * fit into &struct ieee80211_tx_info.
5392 *
5393 * Calls to this function for a single hardware must be synchronized
5394 * against each other. Calls to this function, ieee80211_tx_status_ni()
5395 * and ieee80211_tx_status_irqsafe() may not be mixed for a single hardware.
5396 *
5397 * @hw: the hardware the frame was transmitted by
5398 * @status: tx status information
5399 */
5400void ieee80211_tx_status_ext(struct ieee80211_hw *hw,
5401 struct ieee80211_tx_status *status);
5402
5403/**
5404 * ieee80211_tx_status_noskb - transmit status callback without skb
5405 *
5406 * This function can be used as a replacement for ieee80211_tx_status_skb()
5407 * in drivers that cannot reliably map tx status information back to
5408 * specific skbs.
5409 *
5410 * Calls to this function for a single hardware must be synchronized
5411 * against each other. Calls to this function, ieee80211_tx_status_ni()
5412 * and ieee80211_tx_status_irqsafe() may not be mixed for a single hardware.
5413 *
5414 * @hw: the hardware the frame was transmitted by
5415 * @sta: the receiver station to which this packet is sent
5416 * (NULL for multicast packets)
5417 * @info: tx status information
5418 */
5419static inline void ieee80211_tx_status_noskb(struct ieee80211_hw *hw,
5420 struct ieee80211_sta *sta,
5421 struct ieee80211_tx_info *info)
5422{
5423 struct ieee80211_tx_status status = {
5424 .sta = sta,
5425 .info = info,
5426 };
5427
5428 ieee80211_tx_status_ext(hw, &status);
5429}
5430
5431/**
5432 * ieee80211_tx_status_ni - transmit status callback (in process context)
5433 *
5434 * Like ieee80211_tx_status_skb() but can be called in process context.
5435 *
5436 * Calls to this function, ieee80211_tx_status_skb() and
5437 * ieee80211_tx_status_irqsafe() may not be mixed
5438 * for a single hardware.
5439 *
5440 * @hw: the hardware the frame was transmitted by
5441 * @skb: the frame that was transmitted, owned by mac80211 after this call
5442 */
5443static inline void ieee80211_tx_status_ni(struct ieee80211_hw *hw,
5444 struct sk_buff *skb)
5445{
5446 local_bh_disable();
5447 ieee80211_tx_status_skb(hw, skb);
5448 local_bh_enable();
5449}
5450
5451/**
5452 * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback
5453 *
5454 * Like ieee80211_tx_status_skb() but can be called in IRQ context
5455 * (internally defers to a tasklet.)
5456 *
5457 * Calls to this function, ieee80211_tx_status_skb() and
5458 * ieee80211_tx_status_ni() may not be mixed for a single hardware.
5459 *
5460 * @hw: the hardware the frame was transmitted by
5461 * @skb: the frame that was transmitted, owned by mac80211 after this call
5462 */
5463void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
5464 struct sk_buff *skb);
5465
5466/**
5467 * ieee80211_report_low_ack - report non-responding station
5468 *
5469 * When operating in AP-mode, call this function to report a non-responding
5470 * connected STA.
5471 *
5472 * @sta: the non-responding connected sta
5473 * @num_packets: number of packets sent to @sta without a response
5474 */
5475void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets);
5476
5477#define IEEE80211_MAX_CNTDWN_COUNTERS_NUM 2
5478
5479/**
5480 * struct ieee80211_mutable_offsets - mutable beacon offsets
5481 * @tim_offset: position of TIM element
5482 * @tim_length: size of TIM element
5483 * @cntdwn_counter_offs: array of IEEE80211_MAX_CNTDWN_COUNTERS_NUM offsets
5484 * to countdown counters. This array can contain zero values which
5485 * should be ignored.
5486 * @mbssid_off: position of the multiple bssid element
5487 */
5488struct ieee80211_mutable_offsets {
5489 u16 tim_offset;
5490 u16 tim_length;
5491
5492 u16 cntdwn_counter_offs[IEEE80211_MAX_CNTDWN_COUNTERS_NUM];
5493 u16 mbssid_off;
5494};
5495
5496/**
5497 * ieee80211_beacon_get_template - beacon template generation function
5498 * @hw: pointer obtained from ieee80211_alloc_hw().
5499 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5500 * @offs: &struct ieee80211_mutable_offsets pointer to struct that will
5501 * receive the offsets that may be updated by the driver.
5502 * @link_id: the link id to which the beacon belongs (or 0 for an AP STA
5503 * that is not associated with AP MLD).
5504 *
5505 * If the driver implements beaconing modes, it must use this function to
5506 * obtain the beacon template.
5507 *
5508 * This function should be used if the beacon frames are generated by the
5509 * device, and then the driver must use the returned beacon as the template
5510 * The driver or the device are responsible to update the DTIM and, when
5511 * applicable, the CSA count.
5512 *
5513 * The driver is responsible for freeing the returned skb.
5514 *
5515 * Return: The beacon template. %NULL on error.
5516 */
5517struct sk_buff *
5518ieee80211_beacon_get_template(struct ieee80211_hw *hw,
5519 struct ieee80211_vif *vif,
5520 struct ieee80211_mutable_offsets *offs,
5521 unsigned int link_id);
5522
5523/**
5524 * ieee80211_beacon_get_template_ema_index - EMA beacon template generation
5525 * @hw: pointer obtained from ieee80211_alloc_hw().
5526 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5527 * @offs: &struct ieee80211_mutable_offsets pointer to struct that will
5528 * receive the offsets that may be updated by the driver.
5529 * @link_id: the link id to which the beacon belongs (or 0 for a non-MLD AP).
5530 * @ema_index: index of the beacon in the EMA set.
5531 *
5532 * This function follows the same rules as ieee80211_beacon_get_template()
5533 * but returns a beacon template which includes multiple BSSID element at the
5534 * requested index.
5535 *
5536 * Return: The beacon template. %NULL indicates the end of EMA templates.
5537 */
5538struct sk_buff *
5539ieee80211_beacon_get_template_ema_index(struct ieee80211_hw *hw,
5540 struct ieee80211_vif *vif,
5541 struct ieee80211_mutable_offsets *offs,
5542 unsigned int link_id, u8 ema_index);
5543
5544/**
5545 * struct ieee80211_ema_beacons - List of EMA beacons
5546 * @cnt: count of EMA beacons.
5547 *
5548 * @bcn: array of EMA beacons.
5549 * @bcn.skb: the skb containing this specific beacon
5550 * @bcn.offs: &struct ieee80211_mutable_offsets pointer to struct that will
5551 * receive the offsets that may be updated by the driver.
5552 */
5553struct ieee80211_ema_beacons {
5554 u8 cnt;
5555 struct {
5556 struct sk_buff *skb;
5557 struct ieee80211_mutable_offsets offs;
5558 } bcn[];
5559};
5560
5561/**
5562 * ieee80211_beacon_get_template_ema_list - EMA beacon template generation
5563 * @hw: pointer obtained from ieee80211_alloc_hw().
5564 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5565 * @link_id: the link id to which the beacon belongs (or 0 for a non-MLD AP)
5566 *
5567 * This function follows the same rules as ieee80211_beacon_get_template()
5568 * but allocates and returns a pointer to list of all beacon templates required
5569 * to cover all profiles in the multiple BSSID set. Each template includes only
5570 * one multiple BSSID element.
5571 *
5572 * Driver must call ieee80211_beacon_free_ema_list() to free the memory.
5573 *
5574 * Return: EMA beacon templates of type struct ieee80211_ema_beacons *.
5575 * %NULL on error.
5576 */
5577struct ieee80211_ema_beacons *
5578ieee80211_beacon_get_template_ema_list(struct ieee80211_hw *hw,
5579 struct ieee80211_vif *vif,
5580 unsigned int link_id);
5581
5582/**
5583 * ieee80211_beacon_free_ema_list - free an EMA beacon template list
5584 * @ema_beacons: list of EMA beacons of type &struct ieee80211_ema_beacons pointers.
5585 *
5586 * This function will free a list previously acquired by calling
5587 * ieee80211_beacon_get_template_ema_list()
5588 */
5589void ieee80211_beacon_free_ema_list(struct ieee80211_ema_beacons *ema_beacons);
5590
5591/**
5592 * ieee80211_beacon_get_tim - beacon generation function
5593 * @hw: pointer obtained from ieee80211_alloc_hw().
5594 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5595 * @tim_offset: pointer to variable that will receive the TIM IE offset.
5596 * Set to 0 if invalid (in non-AP modes).
5597 * @tim_length: pointer to variable that will receive the TIM IE length,
5598 * (including the ID and length bytes!).
5599 * Set to 0 if invalid (in non-AP modes).
5600 * @link_id: the link id to which the beacon belongs (or 0 for an AP STA
5601 * that is not associated with AP MLD).
5602 *
5603 * If the driver implements beaconing modes, it must use this function to
5604 * obtain the beacon frame.
5605 *
5606 * If the beacon frames are generated by the host system (i.e., not in
5607 * hardware/firmware), the driver uses this function to get each beacon
5608 * frame from mac80211 -- it is responsible for calling this function exactly
5609 * once before the beacon is needed (e.g. based on hardware interrupt).
5610 *
5611 * The driver is responsible for freeing the returned skb.
5612 *
5613 * Return: The beacon template. %NULL on error.
5614 */
5615struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw,
5616 struct ieee80211_vif *vif,
5617 u16 *tim_offset, u16 *tim_length,
5618 unsigned int link_id);
5619
5620/**
5621 * ieee80211_beacon_get - beacon generation function
5622 * @hw: pointer obtained from ieee80211_alloc_hw().
5623 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5624 * @link_id: the link id to which the beacon belongs (or 0 for an AP STA
5625 * that is not associated with AP MLD).
5626 *
5627 * See ieee80211_beacon_get_tim().
5628 *
5629 * Return: See ieee80211_beacon_get_tim().
5630 */
5631static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
5632 struct ieee80211_vif *vif,
5633 unsigned int link_id)
5634{
5635 return ieee80211_beacon_get_tim(hw, vif, NULL, NULL, link_id);
5636}
5637
5638/**
5639 * ieee80211_beacon_update_cntdwn - request mac80211 to decrement the beacon countdown
5640 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5641 * @link_id: valid link_id during MLO or 0 for non-MLO
5642 *
5643 * The beacon counter should be updated after each beacon transmission.
5644 * This function is called implicitly when
5645 * ieee80211_beacon_get/ieee80211_beacon_get_tim are called, however if the
5646 * beacon frames are generated by the device, the driver should call this
5647 * function after each beacon transmission to sync mac80211's beacon countdown.
5648 *
5649 * Return: new countdown value
5650 */
5651u8 ieee80211_beacon_update_cntdwn(struct ieee80211_vif *vif,
5652 unsigned int link_id);
5653
5654/**
5655 * ieee80211_beacon_set_cntdwn - request mac80211 to set beacon countdown
5656 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5657 * @counter: the new value for the counter
5658 *
5659 * The beacon countdown can be changed by the device, this API should be
5660 * used by the device driver to update csa counter in mac80211.
5661 *
5662 * It should never be used together with ieee80211_beacon_update_cntdwn(),
5663 * as it will cause a race condition around the counter value.
5664 */
5665void ieee80211_beacon_set_cntdwn(struct ieee80211_vif *vif, u8 counter);
5666
5667/**
5668 * ieee80211_csa_finish - notify mac80211 about channel switch
5669 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5670 * @link_id: valid link_id during MLO or 0 for non-MLO
5671 *
5672 * After a channel switch announcement was scheduled and the counter in this
5673 * announcement hits 1, this function must be called by the driver to
5674 * notify mac80211 that the channel can be changed.
5675 */
5676void ieee80211_csa_finish(struct ieee80211_vif *vif, unsigned int link_id);
5677
5678/**
5679 * ieee80211_beacon_cntdwn_is_complete - find out if countdown reached 1
5680 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5681 * @link_id: valid link_id during MLO or 0 for non-MLO
5682 *
5683 * Return: %true if the countdown reached 1, %false otherwise
5684 */
5685bool ieee80211_beacon_cntdwn_is_complete(struct ieee80211_vif *vif,
5686 unsigned int link_id);
5687
5688/**
5689 * ieee80211_color_change_finish - notify mac80211 about color change
5690 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5691 * @link_id: valid link_id during MLO or 0 for non-MLO
5692 *
5693 * After a color change announcement was scheduled and the counter in this
5694 * announcement hits 1, this function must be called by the driver to
5695 * notify mac80211 that the color can be changed
5696 */
5697void ieee80211_color_change_finish(struct ieee80211_vif *vif, u8 link_id);
5698
5699/**
5700 * ieee80211_proberesp_get - retrieve a Probe Response template
5701 * @hw: pointer obtained from ieee80211_alloc_hw().
5702 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5703 *
5704 * Creates a Probe Response template which can, for example, be uploaded to
5705 * hardware. The destination address should be set by the caller.
5706 *
5707 * Can only be called in AP mode.
5708 *
5709 * Return: The Probe Response template. %NULL on error.
5710 */
5711struct sk_buff *ieee80211_proberesp_get(struct ieee80211_hw *hw,
5712 struct ieee80211_vif *vif);
5713
5714/**
5715 * ieee80211_pspoll_get - retrieve a PS Poll template
5716 * @hw: pointer obtained from ieee80211_alloc_hw().
5717 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5718 *
5719 * Creates a PS Poll a template which can, for example, uploaded to
5720 * hardware. The template must be updated after association so that correct
5721 * AID, BSSID and MAC address is used.
5722 *
5723 * Note: Caller (or hardware) is responsible for setting the
5724 * &IEEE80211_FCTL_PM bit.
5725 *
5726 * Return: The PS Poll template. %NULL on error.
5727 */
5728struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw,
5729 struct ieee80211_vif *vif);
5730
5731/**
5732 * ieee80211_nullfunc_get - retrieve a nullfunc template
5733 * @hw: pointer obtained from ieee80211_alloc_hw().
5734 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5735 * @link_id: If the vif is an MLD, get a frame with the link addresses
5736 * for the given link ID. For a link_id < 0 you get a frame with
5737 * MLD addresses, however useful that might be.
5738 * @qos_ok: QoS NDP is acceptable to the caller, this should be set
5739 * if at all possible
5740 *
5741 * Creates a Nullfunc template which can, for example, uploaded to
5742 * hardware. The template must be updated after association so that correct
5743 * BSSID and address is used.
5744 *
5745 * If @qos_ndp is set and the association is to an AP with QoS/WMM, the
5746 * returned packet will be QoS NDP.
5747 *
5748 * Note: Caller (or hardware) is responsible for setting the
5749 * &IEEE80211_FCTL_PM bit as well as Duration and Sequence Control fields.
5750 *
5751 * Return: The nullfunc template. %NULL on error.
5752 */
5753struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw,
5754 struct ieee80211_vif *vif,
5755 int link_id, bool qos_ok);
5756
5757/**
5758 * ieee80211_probereq_get - retrieve a Probe Request template
5759 * @hw: pointer obtained from ieee80211_alloc_hw().
5760 * @src_addr: source MAC address
5761 * @ssid: SSID buffer
5762 * @ssid_len: length of SSID
5763 * @tailroom: tailroom to reserve at end of SKB for IEs
5764 *
5765 * Creates a Probe Request template which can, for example, be uploaded to
5766 * hardware.
5767 *
5768 * Return: The Probe Request template. %NULL on error.
5769 */
5770struct sk_buff *ieee80211_probereq_get(struct ieee80211_hw *hw,
5771 const u8 *src_addr,
5772 const u8 *ssid, size_t ssid_len,
5773 size_t tailroom);
5774
5775/**
5776 * ieee80211_rts_get - RTS frame generation function
5777 * @hw: pointer obtained from ieee80211_alloc_hw().
5778 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5779 * @frame: pointer to the frame that is going to be protected by the RTS.
5780 * @frame_len: the frame length (in octets).
5781 * @frame_txctl: &struct ieee80211_tx_info of the frame.
5782 * @rts: The buffer where to store the RTS frame.
5783 *
5784 * If the RTS frames are generated by the host system (i.e., not in
5785 * hardware/firmware), the low-level driver uses this function to receive
5786 * the next RTS frame from the 802.11 code. The low-level is responsible
5787 * for calling this function before and RTS frame is needed.
5788 */
5789void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
5790 const void *frame, size_t frame_len,
5791 const struct ieee80211_tx_info *frame_txctl,
5792 struct ieee80211_rts *rts);
5793
5794/**
5795 * ieee80211_rts_duration - Get the duration field for an RTS frame
5796 * @hw: pointer obtained from ieee80211_alloc_hw().
5797 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5798 * @frame_len: the length of the frame that is going to be protected by the RTS.
5799 * @frame_txctl: &struct ieee80211_tx_info of the frame.
5800 *
5801 * If the RTS is generated in firmware, but the host system must provide
5802 * the duration field, the low-level driver uses this function to receive
5803 * the duration field value in little-endian byteorder.
5804 *
5805 * Return: The duration.
5806 */
5807__le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
5808 struct ieee80211_vif *vif, size_t frame_len,
5809 const struct ieee80211_tx_info *frame_txctl);
5810
5811/**
5812 * ieee80211_ctstoself_get - CTS-to-self frame generation function
5813 * @hw: pointer obtained from ieee80211_alloc_hw().
5814 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5815 * @frame: pointer to the frame that is going to be protected by the CTS-to-self.
5816 * @frame_len: the frame length (in octets).
5817 * @frame_txctl: &struct ieee80211_tx_info of the frame.
5818 * @cts: The buffer where to store the CTS-to-self frame.
5819 *
5820 * If the CTS-to-self frames are generated by the host system (i.e., not in
5821 * hardware/firmware), the low-level driver uses this function to receive
5822 * the next CTS-to-self frame from the 802.11 code. The low-level is responsible
5823 * for calling this function before and CTS-to-self frame is needed.
5824 */
5825void ieee80211_ctstoself_get(struct ieee80211_hw *hw,
5826 struct ieee80211_vif *vif,
5827 const void *frame, size_t frame_len,
5828 const struct ieee80211_tx_info *frame_txctl,
5829 struct ieee80211_cts *cts);
5830
5831/**
5832 * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
5833 * @hw: pointer obtained from ieee80211_alloc_hw().
5834 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5835 * @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
5836 * @frame_txctl: &struct ieee80211_tx_info of the frame.
5837 *
5838 * If the CTS-to-self is generated in firmware, but the host system must provide
5839 * the duration field, the low-level driver uses this function to receive
5840 * the duration field value in little-endian byteorder.
5841 *
5842 * Return: The duration.
5843 */
5844__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
5845 struct ieee80211_vif *vif,
5846 size_t frame_len,
5847 const struct ieee80211_tx_info *frame_txctl);
5848
5849/**
5850 * ieee80211_generic_frame_duration - Calculate the duration field for a frame
5851 * @hw: pointer obtained from ieee80211_alloc_hw().
5852 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5853 * @band: the band to calculate the frame duration on
5854 * @frame_len: the length of the frame.
5855 * @rate: the rate at which the frame is going to be transmitted.
5856 *
5857 * Calculate the duration field of some generic frame, given its
5858 * length and transmission rate (in 100kbps).
5859 *
5860 * Return: The duration.
5861 */
5862__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
5863 struct ieee80211_vif *vif,
5864 enum nl80211_band band,
5865 size_t frame_len,
5866 struct ieee80211_rate *rate);
5867
5868/**
5869 * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
5870 * @hw: pointer as obtained from ieee80211_alloc_hw().
5871 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5872 *
5873 * Function for accessing buffered broadcast and multicast frames. If
5874 * hardware/firmware does not implement buffering of broadcast/multicast
5875 * frames when power saving is used, 802.11 code buffers them in the host
5876 * memory. The low-level driver uses this function to fetch next buffered
5877 * frame. In most cases, this is used when generating beacon frame.
5878 *
5879 * Return: A pointer to the next buffered skb or NULL if no more buffered
5880 * frames are available.
5881 *
5882 * Note: buffered frames are returned only after DTIM beacon frame was
5883 * generated with ieee80211_beacon_get() and the low-level driver must thus
5884 * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns
5885 * NULL if the previous generated beacon was not DTIM, so the low-level driver
5886 * does not need to check for DTIM beacons separately and should be able to
5887 * use common code for all beacons.
5888 */
5889struct sk_buff *
5890ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
5891
5892/**
5893 * ieee80211_get_tkip_p1k_iv - get a TKIP phase 1 key for IV32
5894 *
5895 * This function returns the TKIP phase 1 key for the given IV32.
5896 *
5897 * @keyconf: the parameter passed with the set key
5898 * @iv32: IV32 to get the P1K for
5899 * @p1k: a buffer to which the key will be written, as 5 u16 values
5900 */
5901void ieee80211_get_tkip_p1k_iv(struct ieee80211_key_conf *keyconf,
5902 u32 iv32, u16 *p1k);
5903
5904/**
5905 * ieee80211_get_tkip_p1k - get a TKIP phase 1 key
5906 *
5907 * This function returns the TKIP phase 1 key for the IV32 taken
5908 * from the given packet.
5909 *
5910 * @keyconf: the parameter passed with the set key
5911 * @skb: the packet to take the IV32 value from that will be encrypted
5912 * with this P1K
5913 * @p1k: a buffer to which the key will be written, as 5 u16 values
5914 */
5915static inline void ieee80211_get_tkip_p1k(struct ieee80211_key_conf *keyconf,
5916 struct sk_buff *skb, u16 *p1k)
5917{
5918 struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
5919 const u8 *data = (u8 *)hdr + ieee80211_hdrlen(hdr->frame_control);
5920 u32 iv32 = get_unaligned_le32(&data[4]);
5921
5922 ieee80211_get_tkip_p1k_iv(keyconf, iv32, p1k);
5923}
5924
5925/**
5926 * ieee80211_get_tkip_rx_p1k - get a TKIP phase 1 key for RX
5927 *
5928 * This function returns the TKIP phase 1 key for the given IV32
5929 * and transmitter address.
5930 *
5931 * @keyconf: the parameter passed with the set key
5932 * @ta: TA that will be used with the key
5933 * @iv32: IV32 to get the P1K for
5934 * @p1k: a buffer to which the key will be written, as 5 u16 values
5935 */
5936void ieee80211_get_tkip_rx_p1k(struct ieee80211_key_conf *keyconf,
5937 const u8 *ta, u32 iv32, u16 *p1k);
5938
5939/**
5940 * ieee80211_get_tkip_p2k - get a TKIP phase 2 key
5941 *
5942 * This function computes the TKIP RC4 key for the IV values
5943 * in the packet.
5944 *
5945 * @keyconf: the parameter passed with the set key
5946 * @skb: the packet to take the IV32/IV16 values from that will be
5947 * encrypted with this key
5948 * @p2k: a buffer to which the key will be written, 16 bytes
5949 */
5950void ieee80211_get_tkip_p2k(struct ieee80211_key_conf *keyconf,
5951 struct sk_buff *skb, u8 *p2k);
5952
5953/**
5954 * ieee80211_tkip_add_iv - write TKIP IV and Ext. IV to pos
5955 *
5956 * @pos: start of crypto header
5957 * @keyconf: the parameter passed with the set key
5958 * @pn: PN to add
5959 *
5960 * Returns: pointer to the octet following IVs (i.e. beginning of
5961 * the packet payload)
5962 *
5963 * This function writes the tkip IV value to pos (which should
5964 * point to the crypto header)
5965 */
5966u8 *ieee80211_tkip_add_iv(u8 *pos, struct ieee80211_key_conf *keyconf, u64 pn);
5967
5968/**
5969 * ieee80211_get_key_rx_seq - get key RX sequence counter
5970 *
5971 * @keyconf: the parameter passed with the set key
5972 * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only);
5973 * the value on TID 0 is also used for non-QoS frames. For
5974 * CMAC, only TID 0 is valid.
5975 * @seq: buffer to receive the sequence data
5976 *
5977 * This function allows a driver to retrieve the current RX IV/PNs
5978 * for the given key. It must not be called if IV checking is done
5979 * by the device and not by mac80211.
5980 *
5981 * Note that this function may only be called when no RX processing
5982 * can be done concurrently.
5983 */
5984void ieee80211_get_key_rx_seq(struct ieee80211_key_conf *keyconf,
5985 int tid, struct ieee80211_key_seq *seq);
5986
5987/**
5988 * ieee80211_set_key_rx_seq - set key RX sequence counter
5989 *
5990 * @keyconf: the parameter passed with the set key
5991 * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only);
5992 * the value on TID 0 is also used for non-QoS frames. For
5993 * CMAC, only TID 0 is valid.
5994 * @seq: new sequence data
5995 *
5996 * This function allows a driver to set the current RX IV/PNs for the
5997 * given key. This is useful when resuming from WoWLAN sleep and GTK
5998 * rekey may have been done while suspended. It should not be called
5999 * if IV checking is done by the device and not by mac80211.
6000 *
6001 * Note that this function may only be called when no RX processing
6002 * can be done concurrently.
6003 */
6004void ieee80211_set_key_rx_seq(struct ieee80211_key_conf *keyconf,
6005 int tid, struct ieee80211_key_seq *seq);
6006
6007/**
6008 * ieee80211_remove_key - remove the given key
6009 * @keyconf: the parameter passed with the set key
6010 *
6011 * Context: Must be called with the wiphy mutex held.
6012 *
6013 * Remove the given key. If the key was uploaded to the hardware at the
6014 * time this function is called, it is not deleted in the hardware but
6015 * instead assumed to have been removed already.
6016 */
6017void ieee80211_remove_key(struct ieee80211_key_conf *keyconf);
6018
6019/**
6020 * ieee80211_gtk_rekey_add - add a GTK key from rekeying during WoWLAN
6021 * @vif: the virtual interface to add the key on
6022 * @keyconf: new key data
6023 * @link_id: the link id of the key or -1 for non-MLO
6024 *
6025 * When GTK rekeying was done while the system was suspended, (a) new
6026 * key(s) will be available. These will be needed by mac80211 for proper
6027 * RX processing, so this function allows setting them.
6028 *
6029 * Return: the newly allocated key structure, which will have
6030 * similar contents to the passed key configuration but point to
6031 * mac80211-owned memory. In case of errors, the function returns an
6032 * ERR_PTR(), use IS_ERR() etc.
6033 *
6034 * Note that this function assumes the key isn't added to hardware
6035 * acceleration, so no TX will be done with the key. Since it's a GTK
6036 * on managed (station) networks, this is true anyway. If the driver
6037 * calls this function from the resume callback and subsequently uses
6038 * the return code 1 to reconfigure the device, this key will be part
6039 * of the reconfiguration.
6040 *
6041 * Note that the driver should also call ieee80211_set_key_rx_seq()
6042 * for the new key for each TID to set up sequence counters properly.
6043 *
6044 * IMPORTANT: If this replaces a key that is present in the hardware,
6045 * then it will attempt to remove it during this call. In many cases
6046 * this isn't what you want, so call ieee80211_remove_key() first for
6047 * the key that's being replaced.
6048 */
6049struct ieee80211_key_conf *
6050ieee80211_gtk_rekey_add(struct ieee80211_vif *vif,
6051 struct ieee80211_key_conf *keyconf,
6052 int link_id);
6053
6054/**
6055 * ieee80211_gtk_rekey_notify - notify userspace supplicant of rekeying
6056 * @vif: virtual interface the rekeying was done on
6057 * @bssid: The BSSID of the AP, for checking association
6058 * @replay_ctr: the new replay counter after GTK rekeying
6059 * @gfp: allocation flags
6060 */
6061void ieee80211_gtk_rekey_notify(struct ieee80211_vif *vif, const u8 *bssid,
6062 const u8 *replay_ctr, gfp_t gfp);
6063
6064/**
6065 * ieee80211_key_mic_failure - increment MIC failure counter for the key
6066 *
6067 * Note: this is really only safe if no other RX function is called
6068 * at the same time.
6069 *
6070 * @keyconf: the key in question
6071 */
6072void ieee80211_key_mic_failure(struct ieee80211_key_conf *keyconf);
6073
6074/**
6075 * ieee80211_key_replay - increment replay counter for the key
6076 *
6077 * Note: this is really only safe if no other RX function is called
6078 * at the same time.
6079 *
6080 * @keyconf: the key in question
6081 */
6082void ieee80211_key_replay(struct ieee80211_key_conf *keyconf);
6083
6084/**
6085 * ieee80211_wake_queue - wake specific queue
6086 * @hw: pointer as obtained from ieee80211_alloc_hw().
6087 * @queue: queue number (counted from zero).
6088 *
6089 * Drivers must use this function instead of netif_wake_queue.
6090 */
6091void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue);
6092
6093/**
6094 * ieee80211_stop_queue - stop specific queue
6095 * @hw: pointer as obtained from ieee80211_alloc_hw().
6096 * @queue: queue number (counted from zero).
6097 *
6098 * Drivers must use this function instead of netif_stop_queue.
6099 */
6100void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue);
6101
6102/**
6103 * ieee80211_queue_stopped - test status of the queue
6104 * @hw: pointer as obtained from ieee80211_alloc_hw().
6105 * @queue: queue number (counted from zero).
6106 *
6107 * Drivers must use this function instead of netif_queue_stopped.
6108 *
6109 * Return: %true if the queue is stopped. %false otherwise.
6110 */
6111
6112int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue);
6113
6114/**
6115 * ieee80211_stop_queues - stop all queues
6116 * @hw: pointer as obtained from ieee80211_alloc_hw().
6117 *
6118 * Drivers must use this function instead of netif_tx_stop_all_queues.
6119 */
6120void ieee80211_stop_queues(struct ieee80211_hw *hw);
6121
6122/**
6123 * ieee80211_wake_queues - wake all queues
6124 * @hw: pointer as obtained from ieee80211_alloc_hw().
6125 *
6126 * Drivers must use this function instead of netif_tx_wake_all_queues.
6127 */
6128void ieee80211_wake_queues(struct ieee80211_hw *hw);
6129
6130/**
6131 * ieee80211_scan_completed - completed hardware scan
6132 *
6133 * When hardware scan offload is used (i.e. the hw_scan() callback is
6134 * assigned) this function needs to be called by the driver to notify
6135 * mac80211 that the scan finished. This function can be called from
6136 * any context, including hardirq context.
6137 *
6138 * @hw: the hardware that finished the scan
6139 * @info: information about the completed scan
6140 */
6141void ieee80211_scan_completed(struct ieee80211_hw *hw,
6142 struct cfg80211_scan_info *info);
6143
6144/**
6145 * ieee80211_sched_scan_results - got results from scheduled scan
6146 *
6147 * When a scheduled scan is running, this function needs to be called by the
6148 * driver whenever there are new scan results available.
6149 *
6150 * @hw: the hardware that is performing scheduled scans
6151 */
6152void ieee80211_sched_scan_results(struct ieee80211_hw *hw);
6153
6154/**
6155 * ieee80211_sched_scan_stopped - inform that the scheduled scan has stopped
6156 *
6157 * When a scheduled scan is running, this function can be called by
6158 * the driver if it needs to stop the scan to perform another task.
6159 * Usual scenarios are drivers that cannot continue the scheduled scan
6160 * while associating, for instance.
6161 *
6162 * @hw: the hardware that is performing scheduled scans
6163 */
6164void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw);
6165
6166/**
6167 * enum ieee80211_interface_iteration_flags - interface iteration flags
6168 * @IEEE80211_IFACE_ITER_NORMAL: Iterate over all interfaces that have
6169 * been added to the driver; However, note that during hardware
6170 * reconfiguration (after restart_hw) it will iterate over a new
6171 * interface and over all the existing interfaces even if they
6172 * haven't been re-added to the driver yet.
6173 * @IEEE80211_IFACE_ITER_RESUME_ALL: During resume, iterate over all
6174 * interfaces, even if they haven't been re-added to the driver yet.
6175 * @IEEE80211_IFACE_ITER_ACTIVE: Iterate only active interfaces (netdev is up).
6176 * @IEEE80211_IFACE_SKIP_SDATA_NOT_IN_DRIVER: Skip any interfaces where SDATA
6177 * is not in the driver. This may fix crashes during firmware recovery
6178 * for instance.
6179 */
6180enum ieee80211_interface_iteration_flags {
6181 IEEE80211_IFACE_ITER_NORMAL = 0,
6182 IEEE80211_IFACE_ITER_RESUME_ALL = BIT(0),
6183 IEEE80211_IFACE_ITER_ACTIVE = BIT(1),
6184 IEEE80211_IFACE_SKIP_SDATA_NOT_IN_DRIVER = BIT(2),
6185};
6186
6187/**
6188 * ieee80211_iterate_interfaces - iterate interfaces
6189 *
6190 * This function iterates over the interfaces associated with a given
6191 * hardware and calls the callback for them. This includes active as well as
6192 * inactive interfaces. This function allows the iterator function to sleep.
6193 * Will iterate over a new interface during add_interface().
6194 *
6195 * @hw: the hardware struct of which the interfaces should be iterated over
6196 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
6197 * @iterator: the iterator function to call
6198 * @data: first argument of the iterator function
6199 */
6200void ieee80211_iterate_interfaces(struct ieee80211_hw *hw, u32 iter_flags,
6201 void (*iterator)(void *data, u8 *mac,
6202 struct ieee80211_vif *vif),
6203 void *data);
6204
6205/**
6206 * ieee80211_iterate_active_interfaces - iterate active interfaces
6207 *
6208 * This function iterates over the interfaces associated with a given
6209 * hardware that are currently active and calls the callback for them.
6210 * This function allows the iterator function to sleep, when the iterator
6211 * function is atomic @ieee80211_iterate_active_interfaces_atomic can
6212 * be used.
6213 * Does not iterate over a new interface during add_interface().
6214 *
6215 * @hw: the hardware struct of which the interfaces should be iterated over
6216 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
6217 * @iterator: the iterator function to call
6218 * @data: first argument of the iterator function
6219 */
6220static inline void
6221ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, u32 iter_flags,
6222 void (*iterator)(void *data, u8 *mac,
6223 struct ieee80211_vif *vif),
6224 void *data)
6225{
6226 ieee80211_iterate_interfaces(hw,
6227 iter_flags | IEEE80211_IFACE_ITER_ACTIVE,
6228 iterator, data);
6229}
6230
6231/**
6232 * ieee80211_iterate_active_interfaces_atomic - iterate active interfaces
6233 *
6234 * This function iterates over the interfaces associated with a given
6235 * hardware that are currently active and calls the callback for them.
6236 * This function requires the iterator callback function to be atomic,
6237 * if that is not desired, use @ieee80211_iterate_active_interfaces instead.
6238 * Does not iterate over a new interface during add_interface().
6239 *
6240 * @hw: the hardware struct of which the interfaces should be iterated over
6241 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
6242 * @iterator: the iterator function to call, cannot sleep
6243 * @data: first argument of the iterator function
6244 */
6245void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw,
6246 u32 iter_flags,
6247 void (*iterator)(void *data,
6248 u8 *mac,
6249 struct ieee80211_vif *vif),
6250 void *data);
6251
6252/**
6253 * ieee80211_iterate_active_interfaces_mtx - iterate active interfaces
6254 *
6255 * This function iterates over the interfaces associated with a given
6256 * hardware that are currently active and calls the callback for them.
6257 * This version can only be used while holding the wiphy mutex.
6258 *
6259 * @hw: the hardware struct of which the interfaces should be iterated over
6260 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
6261 * @iterator: the iterator function to call, cannot sleep
6262 * @data: first argument of the iterator function
6263 */
6264void ieee80211_iterate_active_interfaces_mtx(struct ieee80211_hw *hw,
6265 u32 iter_flags,
6266 void (*iterator)(void *data,
6267 u8 *mac,
6268 struct ieee80211_vif *vif),
6269 void *data);
6270
6271/**
6272 * ieee80211_iterate_stations_atomic - iterate stations
6273 *
6274 * This function iterates over all stations associated with a given
6275 * hardware that are currently uploaded to the driver and calls the callback
6276 * function for them.
6277 * This function requires the iterator callback function to be atomic,
6278 *
6279 * @hw: the hardware struct of which the interfaces should be iterated over
6280 * @iterator: the iterator function to call, cannot sleep
6281 * @data: first argument of the iterator function
6282 */
6283void ieee80211_iterate_stations_atomic(struct ieee80211_hw *hw,
6284 void (*iterator)(void *data,
6285 struct ieee80211_sta *sta),
6286 void *data);
6287
6288/**
6289 * ieee80211_iterate_stations_mtx - iterate stations
6290 *
6291 * This function iterates over all stations associated with a given
6292 * hardware that are currently uploaded to the driver and calls the callback
6293 * function for them. This version can only be used while holding the wiphy
6294 * mutex.
6295 *
6296 * @hw: the hardware struct of which the interfaces should be iterated over
6297 * @iterator: the iterator function to call
6298 * @data: first argument of the iterator function
6299 */
6300void ieee80211_iterate_stations_mtx(struct ieee80211_hw *hw,
6301 void (*iterator)(void *data,
6302 struct ieee80211_sta *sta),
6303 void *data);
6304
6305/**
6306 * ieee80211_queue_work - add work onto the mac80211 workqueue
6307 *
6308 * Drivers and mac80211 use this to add work onto the mac80211 workqueue.
6309 * This helper ensures drivers are not queueing work when they should not be.
6310 *
6311 * @hw: the hardware struct for the interface we are adding work for
6312 * @work: the work we want to add onto the mac80211 workqueue
6313 */
6314void ieee80211_queue_work(struct ieee80211_hw *hw, struct work_struct *work);
6315
6316/**
6317 * ieee80211_queue_delayed_work - add work onto the mac80211 workqueue
6318 *
6319 * Drivers and mac80211 use this to queue delayed work onto the mac80211
6320 * workqueue.
6321 *
6322 * @hw: the hardware struct for the interface we are adding work for
6323 * @dwork: delayable work to queue onto the mac80211 workqueue
6324 * @delay: number of jiffies to wait before queueing
6325 */
6326void ieee80211_queue_delayed_work(struct ieee80211_hw *hw,
6327 struct delayed_work *dwork,
6328 unsigned long delay);
6329
6330/**
6331 * ieee80211_refresh_tx_agg_session_timer - Refresh a tx agg session timer.
6332 * @sta: the station for which to start a BA session
6333 * @tid: the TID to BA on.
6334 *
6335 * This function allows low level driver to refresh tx agg session timer
6336 * to maintain BA session, the session level will still be managed by the
6337 * mac80211.
6338 *
6339 * Note: must be called in an RCU critical section.
6340 */
6341void ieee80211_refresh_tx_agg_session_timer(struct ieee80211_sta *sta,
6342 u16 tid);
6343
6344/**
6345 * ieee80211_start_tx_ba_session - Start a tx Block Ack session.
6346 * @sta: the station for which to start a BA session
6347 * @tid: the TID to BA on.
6348 * @timeout: session timeout value (in TUs)
6349 *
6350 * Return: success if addBA request was sent, failure otherwise
6351 *
6352 * Although mac80211/low level driver/user space application can estimate
6353 * the need to start aggregation on a certain RA/TID, the session level
6354 * will be managed by the mac80211.
6355 */
6356int ieee80211_start_tx_ba_session(struct ieee80211_sta *sta, u16 tid,
6357 u16 timeout);
6358
6359/**
6360 * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate.
6361 * @vif: &struct ieee80211_vif pointer from the add_interface callback
6362 * @ra: receiver address of the BA session recipient.
6363 * @tid: the TID to BA on.
6364 *
6365 * This function must be called by low level driver once it has
6366 * finished with preparations for the BA session. It can be called
6367 * from any context.
6368 */
6369void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
6370 u16 tid);
6371
6372/**
6373 * ieee80211_stop_tx_ba_session - Stop a Block Ack session.
6374 * @sta: the station whose BA session to stop
6375 * @tid: the TID to stop BA.
6376 *
6377 * Return: negative error if the TID is invalid, or no aggregation active
6378 *
6379 * Although mac80211/low level driver/user space application can estimate
6380 * the need to stop aggregation on a certain RA/TID, the session level
6381 * will be managed by the mac80211.
6382 */
6383int ieee80211_stop_tx_ba_session(struct ieee80211_sta *sta, u16 tid);
6384
6385/**
6386 * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate.
6387 * @vif: &struct ieee80211_vif pointer from the add_interface callback
6388 * @ra: receiver address of the BA session recipient.
6389 * @tid: the desired TID to BA on.
6390 *
6391 * This function must be called by low level driver once it has
6392 * finished with preparations for the BA session tear down. It
6393 * can be called from any context.
6394 */
6395void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
6396 u16 tid);
6397
6398/**
6399 * ieee80211_find_sta - find a station
6400 *
6401 * @vif: virtual interface to look for station on
6402 * @addr: station's address
6403 *
6404 * Return: The station, if found. %NULL otherwise.
6405 *
6406 * Note: This function must be called under RCU lock and the
6407 * resulting pointer is only valid under RCU lock as well.
6408 */
6409struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif,
6410 const u8 *addr);
6411
6412/**
6413 * ieee80211_find_sta_by_ifaddr - find a station on hardware
6414 *
6415 * @hw: pointer as obtained from ieee80211_alloc_hw()
6416 * @addr: remote station's address
6417 * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'.
6418 *
6419 * Return: The station, if found. %NULL otherwise.
6420 *
6421 * Note: This function must be called under RCU lock and the
6422 * resulting pointer is only valid under RCU lock as well.
6423 *
6424 * NOTE: You may pass NULL for localaddr, but then you will just get
6425 * the first STA that matches the remote address 'addr'.
6426 * We can have multiple STA associated with multiple
6427 * logical stations (e.g. consider a station connecting to another
6428 * BSSID on the same AP hardware without disconnecting first).
6429 * In this case, the result of this method with localaddr NULL
6430 * is not reliable.
6431 *
6432 * DO NOT USE THIS FUNCTION with localaddr NULL if at all possible.
6433 */
6434struct ieee80211_sta *ieee80211_find_sta_by_ifaddr(struct ieee80211_hw *hw,
6435 const u8 *addr,
6436 const u8 *localaddr);
6437
6438/**
6439 * ieee80211_find_sta_by_link_addrs - find STA by link addresses
6440 * @hw: pointer as obtained from ieee80211_alloc_hw()
6441 * @addr: remote station's link address
6442 * @localaddr: local link address, use %NULL for any (but avoid that)
6443 * @link_id: pointer to obtain the link ID if the STA is found,
6444 * may be %NULL if the link ID is not needed
6445 *
6446 * Obtain the STA by link address, must use RCU protection.
6447 *
6448 * Return: pointer to STA if found, otherwise %NULL.
6449 */
6450struct ieee80211_sta *
6451ieee80211_find_sta_by_link_addrs(struct ieee80211_hw *hw,
6452 const u8 *addr,
6453 const u8 *localaddr,
6454 unsigned int *link_id);
6455
6456/**
6457 * ieee80211_sta_block_awake - block station from waking up
6458 * @hw: the hardware
6459 * @pubsta: the station
6460 * @block: whether to block or unblock
6461 *
6462 * Some devices require that all frames that are on the queues
6463 * for a specific station that went to sleep are flushed before
6464 * a poll response or frames after the station woke up can be
6465 * delivered to that it. Note that such frames must be rejected
6466 * by the driver as filtered, with the appropriate status flag.
6467 *
6468 * This function allows implementing this mode in a race-free
6469 * manner.
6470 *
6471 * To do this, a driver must keep track of the number of frames
6472 * still enqueued for a specific station. If this number is not
6473 * zero when the station goes to sleep, the driver must call
6474 * this function to force mac80211 to consider the station to
6475 * be asleep regardless of the station's actual state. Once the
6476 * number of outstanding frames reaches zero, the driver must
6477 * call this function again to unblock the station. That will
6478 * cause mac80211 to be able to send ps-poll responses, and if
6479 * the station queried in the meantime then frames will also
6480 * be sent out as a result of this. Additionally, the driver
6481 * will be notified that the station woke up some time after
6482 * it is unblocked, regardless of whether the station actually
6483 * woke up while blocked or not.
6484 */
6485void ieee80211_sta_block_awake(struct ieee80211_hw *hw,
6486 struct ieee80211_sta *pubsta, bool block);
6487
6488/**
6489 * ieee80211_sta_eosp - notify mac80211 about end of SP
6490 * @pubsta: the station
6491 *
6492 * When a device transmits frames in a way that it can't tell
6493 * mac80211 in the TX status about the EOSP, it must clear the
6494 * %IEEE80211_TX_STATUS_EOSP bit and call this function instead.
6495 * This applies for PS-Poll as well as uAPSD.
6496 *
6497 * Note that just like with _tx_status() and _rx() drivers must
6498 * not mix calls to irqsafe/non-irqsafe versions, this function
6499 * must not be mixed with those either. Use the all irqsafe, or
6500 * all non-irqsafe, don't mix!
6501 *
6502 * NB: the _irqsafe version of this function doesn't exist, no
6503 * driver needs it right now. Don't call this function if
6504 * you'd need the _irqsafe version, look at the git history
6505 * and restore the _irqsafe version!
6506 */
6507void ieee80211_sta_eosp(struct ieee80211_sta *pubsta);
6508
6509/**
6510 * ieee80211_send_eosp_nullfunc - ask mac80211 to send NDP with EOSP
6511 * @pubsta: the station
6512 * @tid: the tid of the NDP
6513 *
6514 * Sometimes the device understands that it needs to close
6515 * the Service Period unexpectedly. This can happen when
6516 * sending frames that are filling holes in the BA window.
6517 * In this case, the device can ask mac80211 to send a
6518 * Nullfunc frame with EOSP set. When that happens, the
6519 * driver must have called ieee80211_sta_set_buffered() to
6520 * let mac80211 know that there are no buffered frames any
6521 * more, otherwise mac80211 will get the more_data bit wrong.
6522 * The low level driver must have made sure that the frame
6523 * will be sent despite the station being in power-save.
6524 * Mac80211 won't call allow_buffered_frames().
6525 * Note that calling this function, doesn't exempt the driver
6526 * from closing the EOSP properly, it will still have to call
6527 * ieee80211_sta_eosp when the NDP is sent.
6528 */
6529void ieee80211_send_eosp_nullfunc(struct ieee80211_sta *pubsta, int tid);
6530
6531/**
6532 * ieee80211_sta_recalc_aggregates - recalculate aggregate data after a change
6533 * @pubsta: the station
6534 *
6535 * Call this function after changing a per-link aggregate data as referenced in
6536 * &struct ieee80211_sta_aggregates by accessing the agg field of
6537 * &struct ieee80211_link_sta.
6538 *
6539 * With non MLO the data in deflink will be referenced directly. In that case
6540 * there is no need to call this function.
6541 */
6542void ieee80211_sta_recalc_aggregates(struct ieee80211_sta *pubsta);
6543
6544/**
6545 * ieee80211_sta_register_airtime - register airtime usage for a sta/tid
6546 *
6547 * Register airtime usage for a given sta on a given tid. The driver must call
6548 * this function to notify mac80211 that a station used a certain amount of
6549 * airtime. This information will be used by the TXQ scheduler to schedule
6550 * stations in a way that ensures airtime fairness.
6551 *
6552 * The reported airtime should as a minimum include all time that is spent
6553 * transmitting to the remote station, including overhead and padding, but not
6554 * including time spent waiting for a TXOP. If the time is not reported by the
6555 * hardware it can in some cases be calculated from the rate and known frame
6556 * composition. When possible, the time should include any failed transmission
6557 * attempts.
6558 *
6559 * The driver can either call this function synchronously for every packet or
6560 * aggregate, or asynchronously as airtime usage information becomes available.
6561 * TX and RX airtime can be reported together, or separately by setting one of
6562 * them to 0.
6563 *
6564 * @pubsta: the station
6565 * @tid: the TID to register airtime for
6566 * @tx_airtime: airtime used during TX (in usec)
6567 * @rx_airtime: airtime used during RX (in usec)
6568 */
6569void ieee80211_sta_register_airtime(struct ieee80211_sta *pubsta, u8 tid,
6570 u32 tx_airtime, u32 rx_airtime);
6571
6572/**
6573 * ieee80211_txq_airtime_check - check if a txq can send frame to device
6574 *
6575 * @hw: pointer obtained from ieee80211_alloc_hw()
6576 * @txq: pointer obtained from station or virtual interface
6577 *
6578 * Return: %true if the AQL's airtime limit has not been reached and the txq can
6579 * continue to send more packets to the device. Otherwise return %false.
6580 */
6581bool
6582ieee80211_txq_airtime_check(struct ieee80211_hw *hw, struct ieee80211_txq *txq);
6583
6584/**
6585 * ieee80211_iter_keys - iterate keys programmed into the device
6586 * @hw: pointer obtained from ieee80211_alloc_hw()
6587 * @vif: virtual interface to iterate, may be %NULL for all
6588 * @iter: iterator function that will be called for each key
6589 * @iter_data: custom data to pass to the iterator function
6590 *
6591 * Context: Must be called with wiphy mutex held; can sleep.
6592 *
6593 * This function can be used to iterate all the keys known to
6594 * mac80211, even those that weren't previously programmed into
6595 * the device. This is intended for use in WoWLAN if the device
6596 * needs reprogramming of the keys during suspend.
6597 *
6598 * The order in which the keys are iterated matches the order
6599 * in which they were originally installed and handed to the
6600 * set_key callback.
6601 */
6602void ieee80211_iter_keys(struct ieee80211_hw *hw,
6603 struct ieee80211_vif *vif,
6604 void (*iter)(struct ieee80211_hw *hw,
6605 struct ieee80211_vif *vif,
6606 struct ieee80211_sta *sta,
6607 struct ieee80211_key_conf *key,
6608 void *data),
6609 void *iter_data);
6610
6611/**
6612 * ieee80211_iter_keys_rcu - iterate keys programmed into the device
6613 * @hw: pointer obtained from ieee80211_alloc_hw()
6614 * @vif: virtual interface to iterate, may be %NULL for all
6615 * @iter: iterator function that will be called for each key
6616 * @iter_data: custom data to pass to the iterator function
6617 *
6618 * This function can be used to iterate all the keys known to
6619 * mac80211, even those that weren't previously programmed into
6620 * the device. Note that due to locking reasons, keys of station
6621 * in removal process will be skipped.
6622 *
6623 * This function requires being called in an RCU critical section,
6624 * and thus iter must be atomic.
6625 */
6626void ieee80211_iter_keys_rcu(struct ieee80211_hw *hw,
6627 struct ieee80211_vif *vif,
6628 void (*iter)(struct ieee80211_hw *hw,
6629 struct ieee80211_vif *vif,
6630 struct ieee80211_sta *sta,
6631 struct ieee80211_key_conf *key,
6632 void *data),
6633 void *iter_data);
6634
6635/**
6636 * ieee80211_iter_chan_contexts_atomic - iterate channel contexts
6637 * @hw: pointer obtained from ieee80211_alloc_hw().
6638 * @iter: iterator function
6639 * @iter_data: data passed to iterator function
6640 *
6641 * Iterate all active channel contexts. This function is atomic and
6642 * doesn't acquire any locks internally that might be held in other
6643 * places while calling into the driver.
6644 *
6645 * The iterator will not find a context that's being added (during
6646 * the driver callback to add it) but will find it while it's being
6647 * removed.
6648 *
6649 * Note that during hardware restart, all contexts that existed
6650 * before the restart are considered already present so will be
6651 * found while iterating, whether they've been re-added already
6652 * or not.
6653 */
6654void ieee80211_iter_chan_contexts_atomic(
6655 struct ieee80211_hw *hw,
6656 void (*iter)(struct ieee80211_hw *hw,
6657 struct ieee80211_chanctx_conf *chanctx_conf,
6658 void *data),
6659 void *iter_data);
6660
6661/**
6662 * ieee80211_ap_probereq_get - retrieve a Probe Request template
6663 * @hw: pointer obtained from ieee80211_alloc_hw().
6664 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6665 *
6666 * Creates a Probe Request template which can, for example, be uploaded to
6667 * hardware. The template is filled with bssid, ssid and supported rate
6668 * information. This function must only be called from within the
6669 * .bss_info_changed callback function and only in managed mode. The function
6670 * is only useful when the interface is associated, otherwise it will return
6671 * %NULL.
6672 *
6673 * Return: The Probe Request template. %NULL on error.
6674 */
6675struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw,
6676 struct ieee80211_vif *vif);
6677
6678/**
6679 * ieee80211_beacon_loss - inform hardware does not receive beacons
6680 *
6681 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6682 *
6683 * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER and
6684 * %IEEE80211_CONF_PS is set, the driver needs to inform whenever the
6685 * hardware is not receiving beacons with this function.
6686 */
6687void ieee80211_beacon_loss(struct ieee80211_vif *vif);
6688
6689/**
6690 * ieee80211_connection_loss - inform hardware has lost connection to the AP
6691 *
6692 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6693 *
6694 * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER, and
6695 * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver
6696 * needs to inform if the connection to the AP has been lost.
6697 * The function may also be called if the connection needs to be terminated
6698 * for some other reason, even if %IEEE80211_HW_CONNECTION_MONITOR isn't set.
6699 *
6700 * This function will cause immediate change to disassociated state,
6701 * without connection recovery attempts.
6702 */
6703void ieee80211_connection_loss(struct ieee80211_vif *vif);
6704
6705/**
6706 * ieee80211_disconnect - request disconnection
6707 *
6708 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6709 * @reconnect: immediate reconnect is desired
6710 *
6711 * Request disconnection from the current network and, if enabled, send a
6712 * hint to the higher layers that immediate reconnect is desired.
6713 */
6714void ieee80211_disconnect(struct ieee80211_vif *vif, bool reconnect);
6715
6716/**
6717 * ieee80211_resume_disconnect - disconnect from AP after resume
6718 *
6719 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6720 *
6721 * Instructs mac80211 to disconnect from the AP after resume.
6722 * Drivers can use this after WoWLAN if they know that the
6723 * connection cannot be kept up, for example because keys were
6724 * used while the device was asleep but the replay counters or
6725 * similar cannot be retrieved from the device during resume.
6726 *
6727 * Note that due to implementation issues, if the driver uses
6728 * the reconfiguration functionality during resume the interface
6729 * will still be added as associated first during resume and then
6730 * disconnect normally later.
6731 *
6732 * This function can only be called from the resume callback and
6733 * the driver must not be holding any of its own locks while it
6734 * calls this function, or at least not any locks it needs in the
6735 * key configuration paths (if it supports HW crypto).
6736 */
6737void ieee80211_resume_disconnect(struct ieee80211_vif *vif);
6738
6739/**
6740 * ieee80211_hw_restart_disconnect - disconnect from AP after
6741 * hardware restart
6742 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6743 *
6744 * Instructs mac80211 to disconnect from the AP after
6745 * hardware restart.
6746 */
6747void ieee80211_hw_restart_disconnect(struct ieee80211_vif *vif);
6748
6749/**
6750 * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring
6751 * rssi threshold triggered
6752 *
6753 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6754 * @rssi_event: the RSSI trigger event type
6755 * @rssi_level: new RSSI level value or 0 if not available
6756 * @gfp: context flags
6757 *
6758 * When the %IEEE80211_VIF_SUPPORTS_CQM_RSSI is set, and a connection quality
6759 * monitoring is configured with an rssi threshold, the driver will inform
6760 * whenever the rssi level reaches the threshold.
6761 */
6762void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif,
6763 enum nl80211_cqm_rssi_threshold_event rssi_event,
6764 s32 rssi_level,
6765 gfp_t gfp);
6766
6767/**
6768 * ieee80211_cqm_beacon_loss_notify - inform CQM of beacon loss
6769 *
6770 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6771 * @gfp: context flags
6772 */
6773void ieee80211_cqm_beacon_loss_notify(struct ieee80211_vif *vif, gfp_t gfp);
6774
6775/**
6776 * ieee80211_radar_detected - inform that a radar was detected
6777 *
6778 * @hw: pointer as obtained from ieee80211_alloc_hw()
6779 * @chanctx_conf: Channel context on which radar is detected. Mandatory to
6780 * pass a valid pointer during MLO. For non-MLO %NULL can be passed
6781 */
6782void ieee80211_radar_detected(struct ieee80211_hw *hw,
6783 struct ieee80211_chanctx_conf *chanctx_conf);
6784
6785/**
6786 * ieee80211_chswitch_done - Complete channel switch process
6787 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6788 * @success: make the channel switch successful or not
6789 * @link_id: the link_id on which the switch was done. Ignored if success is
6790 * false.
6791 *
6792 * Complete the channel switch post-process: set the new operational channel
6793 * and wake up the suspended queues.
6794 */
6795void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success,
6796 unsigned int link_id);
6797
6798/**
6799 * ieee80211_channel_switch_disconnect - disconnect due to channel switch error
6800 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6801 *
6802 * Instruct mac80211 to disconnect due to a channel switch error. The channel
6803 * switch can request to block the tx and so, we need to make sure we do not send
6804 * a deauth frame in this case.
6805 */
6806void ieee80211_channel_switch_disconnect(struct ieee80211_vif *vif);
6807
6808/**
6809 * ieee80211_request_smps - request SM PS transition
6810 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6811 * @link_id: link ID for MLO, or 0
6812 * @smps_mode: new SM PS mode
6813 *
6814 * This allows the driver to request an SM PS transition in managed
6815 * mode. This is useful when the driver has more information than
6816 * the stack about possible interference, for example by bluetooth.
6817 */
6818void ieee80211_request_smps(struct ieee80211_vif *vif, unsigned int link_id,
6819 enum ieee80211_smps_mode smps_mode);
6820
6821/**
6822 * ieee80211_ready_on_channel - notification of remain-on-channel start
6823 * @hw: pointer as obtained from ieee80211_alloc_hw()
6824 */
6825void ieee80211_ready_on_channel(struct ieee80211_hw *hw);
6826
6827/**
6828 * ieee80211_remain_on_channel_expired - remain_on_channel duration expired
6829 * @hw: pointer as obtained from ieee80211_alloc_hw()
6830 */
6831void ieee80211_remain_on_channel_expired(struct ieee80211_hw *hw);
6832
6833/**
6834 * ieee80211_stop_rx_ba_session - callback to stop existing BA sessions
6835 *
6836 * in order not to harm the system performance and user experience, the device
6837 * may request not to allow any rx ba session and tear down existing rx ba
6838 * sessions based on system constraints such as periodic BT activity that needs
6839 * to limit wlan activity (eg.sco or a2dp)."
6840 * in such cases, the intention is to limit the duration of the rx ppdu and
6841 * therefore prevent the peer device to use a-mpdu aggregation.
6842 *
6843 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6844 * @ba_rx_bitmap: Bit map of open rx ba per tid
6845 * @addr: & to bssid mac address
6846 */
6847void ieee80211_stop_rx_ba_session(struct ieee80211_vif *vif, u16 ba_rx_bitmap,
6848 const u8 *addr);
6849
6850/**
6851 * ieee80211_mark_rx_ba_filtered_frames - move RX BA window and mark filtered
6852 * @pubsta: station struct
6853 * @tid: the session's TID
6854 * @ssn: starting sequence number of the bitmap, all frames before this are
6855 * assumed to be out of the window after the call
6856 * @filtered: bitmap of filtered frames, BIT(0) is the @ssn entry etc.
6857 * @received_mpdus: number of received mpdus in firmware
6858 *
6859 * This function moves the BA window and releases all frames before @ssn, and
6860 * marks frames marked in the bitmap as having been filtered. Afterwards, it
6861 * checks if any frames in the window starting from @ssn can now be released
6862 * (in case they were only waiting for frames that were filtered.)
6863 * (Only work correctly if @max_rx_aggregation_subframes <= 64 frames)
6864 */
6865void ieee80211_mark_rx_ba_filtered_frames(struct ieee80211_sta *pubsta, u8 tid,
6866 u16 ssn, u64 filtered,
6867 u16 received_mpdus);
6868
6869/**
6870 * ieee80211_send_bar - send a BlockAckReq frame
6871 *
6872 * can be used to flush pending frames from the peer's aggregation reorder
6873 * buffer.
6874 *
6875 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6876 * @ra: the peer's destination address
6877 * @tid: the TID of the aggregation session
6878 * @ssn: the new starting sequence number for the receiver
6879 */
6880void ieee80211_send_bar(struct ieee80211_vif *vif, u8 *ra, u16 tid, u16 ssn);
6881
6882/**
6883 * ieee80211_manage_rx_ba_offl - helper to queue an RX BA work
6884 * @vif: &struct ieee80211_vif pointer from the add_interface callback
6885 * @addr: station mac address
6886 * @tid: the rx tid
6887 */
6888void ieee80211_manage_rx_ba_offl(struct ieee80211_vif *vif, const u8 *addr,
6889 unsigned int tid);
6890
6891/**
6892 * ieee80211_start_rx_ba_session_offl - start a Rx BA session
6893 *
6894 * Some device drivers may offload part of the Rx aggregation flow including
6895 * AddBa/DelBa negotiation but may otherwise be incapable of full Rx
6896 * reordering.
6897 *
6898 * Create structures responsible for reordering so device drivers may call here
6899 * when they complete AddBa negotiation.
6900 *
6901 * @vif: &struct ieee80211_vif pointer from the add_interface callback
6902 * @addr: station mac address
6903 * @tid: the rx tid
6904 */
6905static inline void ieee80211_start_rx_ba_session_offl(struct ieee80211_vif *vif,
6906 const u8 *addr, u16 tid)
6907{
6908 if (WARN_ON(tid >= IEEE80211_NUM_TIDS))
6909 return;
6910 ieee80211_manage_rx_ba_offl(vif, addr, tid);
6911}
6912
6913/**
6914 * ieee80211_stop_rx_ba_session_offl - stop a Rx BA session
6915 *
6916 * Some device drivers may offload part of the Rx aggregation flow including
6917 * AddBa/DelBa negotiation but may otherwise be incapable of full Rx
6918 * reordering.
6919 *
6920 * Destroy structures responsible for reordering so device drivers may call here
6921 * when they complete DelBa negotiation.
6922 *
6923 * @vif: &struct ieee80211_vif pointer from the add_interface callback
6924 * @addr: station mac address
6925 * @tid: the rx tid
6926 */
6927static inline void ieee80211_stop_rx_ba_session_offl(struct ieee80211_vif *vif,
6928 const u8 *addr, u16 tid)
6929{
6930 if (WARN_ON(tid >= IEEE80211_NUM_TIDS))
6931 return;
6932 ieee80211_manage_rx_ba_offl(vif, addr, tid + IEEE80211_NUM_TIDS);
6933}
6934
6935/**
6936 * ieee80211_rx_ba_timer_expired - stop a Rx BA session due to timeout
6937 *
6938 * Some device drivers do not offload AddBa/DelBa negotiation, but handle rx
6939 * buffer reording internally, and therefore also handle the session timer.
6940 *
6941 * Trigger the timeout flow, which sends a DelBa.
6942 *
6943 * @vif: &struct ieee80211_vif pointer from the add_interface callback
6944 * @addr: station mac address
6945 * @tid: the rx tid
6946 */
6947void ieee80211_rx_ba_timer_expired(struct ieee80211_vif *vif,
6948 const u8 *addr, unsigned int tid);
6949
6950/* Rate control API */
6951
6952/**
6953 * struct ieee80211_tx_rate_control - rate control information for/from RC algo
6954 *
6955 * @hw: The hardware the algorithm is invoked for.
6956 * @sband: The band this frame is being transmitted on.
6957 * @bss_conf: the current BSS configuration
6958 * @skb: the skb that will be transmitted, the control information in it needs
6959 * to be filled in
6960 * @reported_rate: The rate control algorithm can fill this in to indicate
6961 * which rate should be reported to userspace as the current rate and
6962 * used for rate calculations in the mesh network.
6963 * @rts: whether RTS will be used for this frame because it is longer than the
6964 * RTS threshold
6965 * @short_preamble: whether mac80211 will request short-preamble transmission
6966 * if the selected rate supports it
6967 * @rate_idx_mask: user-requested (legacy) rate mask
6968 * @rate_idx_mcs_mask: user-requested MCS rate mask (NULL if not in use)
6969 * @bss: whether this frame is sent out in AP or IBSS mode
6970 */
6971struct ieee80211_tx_rate_control {
6972 struct ieee80211_hw *hw;
6973 struct ieee80211_supported_band *sband;
6974 struct ieee80211_bss_conf *bss_conf;
6975 struct sk_buff *skb;
6976 struct ieee80211_tx_rate reported_rate;
6977 bool rts, short_preamble;
6978 u32 rate_idx_mask;
6979 u8 *rate_idx_mcs_mask;
6980 bool bss;
6981};
6982
6983/**
6984 * enum rate_control_capabilities - rate control capabilities
6985 */
6986enum rate_control_capabilities {
6987 /**
6988 * @RATE_CTRL_CAPA_VHT_EXT_NSS_BW:
6989 * Support for extended NSS BW support (dot11VHTExtendedNSSCapable)
6990 * Note that this is only looked at if the minimum number of chains
6991 * that the AP uses is < the number of TX chains the hardware has,
6992 * otherwise the NSS difference doesn't bother us.
6993 */
6994 RATE_CTRL_CAPA_VHT_EXT_NSS_BW = BIT(0),
6995 /**
6996 * @RATE_CTRL_CAPA_AMPDU_TRIGGER:
6997 * mac80211 should start A-MPDU sessions on tx
6998 */
6999 RATE_CTRL_CAPA_AMPDU_TRIGGER = BIT(1),
7000};
7001
7002struct rate_control_ops {
7003 unsigned long capa;
7004 const char *name;
7005 void *(*alloc)(struct ieee80211_hw *hw);
7006 void (*add_debugfs)(struct ieee80211_hw *hw, void *priv,
7007 struct dentry *debugfsdir);
7008 void (*free)(void *priv);
7009
7010 void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp);
7011 void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
7012 struct cfg80211_chan_def *chandef,
7013 struct ieee80211_sta *sta, void *priv_sta);
7014 void (*rate_update)(void *priv, struct ieee80211_supported_band *sband,
7015 struct cfg80211_chan_def *chandef,
7016 struct ieee80211_sta *sta, void *priv_sta,
7017 u32 changed);
7018 void (*free_sta)(void *priv, struct ieee80211_sta *sta,
7019 void *priv_sta);
7020
7021 void (*tx_status_ext)(void *priv,
7022 struct ieee80211_supported_band *sband,
7023 void *priv_sta, struct ieee80211_tx_status *st);
7024 void (*tx_status)(void *priv, struct ieee80211_supported_band *sband,
7025 struct ieee80211_sta *sta, void *priv_sta,
7026 struct sk_buff *skb);
7027 void (*get_rate)(void *priv, struct ieee80211_sta *sta, void *priv_sta,
7028 struct ieee80211_tx_rate_control *txrc);
7029
7030 void (*add_sta_debugfs)(void *priv, void *priv_sta,
7031 struct dentry *dir);
7032
7033 u32 (*get_expected_throughput)(void *priv_sta);
7034};
7035
7036static inline int rate_supported(struct ieee80211_sta *sta,
7037 enum nl80211_band band,
7038 int index)
7039{
7040 return (sta == NULL || sta->deflink.supp_rates[band] & BIT(index));
7041}
7042
7043static inline s8
7044rate_lowest_index(struct ieee80211_supported_band *sband,
7045 struct ieee80211_sta *sta)
7046{
7047 int i;
7048
7049 for (i = 0; i < sband->n_bitrates; i++)
7050 if (rate_supported(sta, sband->band, i))
7051 return i;
7052
7053 /* warn when we cannot find a rate. */
7054 WARN_ON_ONCE(1);
7055
7056 /* and return 0 (the lowest index) */
7057 return 0;
7058}
7059
7060static inline
7061bool rate_usable_index_exists(struct ieee80211_supported_band *sband,
7062 struct ieee80211_sta *sta)
7063{
7064 unsigned int i;
7065
7066 for (i = 0; i < sband->n_bitrates; i++)
7067 if (rate_supported(sta, sband->band, i))
7068 return true;
7069 return false;
7070}
7071
7072/**
7073 * rate_control_set_rates - pass the sta rate selection to mac80211/driver
7074 *
7075 * When not doing a rate control probe to test rates, rate control should pass
7076 * its rate selection to mac80211. If the driver supports receiving a station
7077 * rate table, it will use it to ensure that frames are always sent based on
7078 * the most recent rate control module decision.
7079 *
7080 * @hw: pointer as obtained from ieee80211_alloc_hw()
7081 * @pubsta: &struct ieee80211_sta pointer to the target destination.
7082 * @rates: new tx rate set to be used for this station.
7083 *
7084 * Return: 0 on success. An error code otherwise.
7085 */
7086int rate_control_set_rates(struct ieee80211_hw *hw,
7087 struct ieee80211_sta *pubsta,
7088 struct ieee80211_sta_rates *rates);
7089
7090int ieee80211_rate_control_register(const struct rate_control_ops *ops);
7091void ieee80211_rate_control_unregister(const struct rate_control_ops *ops);
7092
7093static inline bool
7094conf_is_ht20(struct ieee80211_conf *conf)
7095{
7096 return conf->chandef.width == NL80211_CHAN_WIDTH_20;
7097}
7098
7099static inline bool
7100conf_is_ht40_minus(struct ieee80211_conf *conf)
7101{
7102 return conf->chandef.width == NL80211_CHAN_WIDTH_40 &&
7103 conf->chandef.center_freq1 < conf->chandef.chan->center_freq;
7104}
7105
7106static inline bool
7107conf_is_ht40_plus(struct ieee80211_conf *conf)
7108{
7109 return conf->chandef.width == NL80211_CHAN_WIDTH_40 &&
7110 conf->chandef.center_freq1 > conf->chandef.chan->center_freq;
7111}
7112
7113static inline bool
7114conf_is_ht40(struct ieee80211_conf *conf)
7115{
7116 return conf->chandef.width == NL80211_CHAN_WIDTH_40;
7117}
7118
7119static inline bool
7120conf_is_ht(struct ieee80211_conf *conf)
7121{
7122 return (conf->chandef.width != NL80211_CHAN_WIDTH_5) &&
7123 (conf->chandef.width != NL80211_CHAN_WIDTH_10) &&
7124 (conf->chandef.width != NL80211_CHAN_WIDTH_20_NOHT);
7125}
7126
7127static inline enum nl80211_iftype
7128ieee80211_iftype_p2p(enum nl80211_iftype type, bool p2p)
7129{
7130 if (p2p) {
7131 switch (type) {
7132 case NL80211_IFTYPE_STATION:
7133 return NL80211_IFTYPE_P2P_CLIENT;
7134 case NL80211_IFTYPE_AP:
7135 return NL80211_IFTYPE_P2P_GO;
7136 default:
7137 break;
7138 }
7139 }
7140 return type;
7141}
7142
7143static inline enum nl80211_iftype
7144ieee80211_vif_type_p2p(struct ieee80211_vif *vif)
7145{
7146 return ieee80211_iftype_p2p(vif->type, vif->p2p);
7147}
7148
7149/**
7150 * ieee80211_get_he_iftype_cap_vif - return HE capabilities for sband/vif
7151 * @sband: the sband to search for the iftype on
7152 * @vif: the vif to get the iftype from
7153 *
7154 * Return: pointer to the struct ieee80211_sta_he_cap, or %NULL is none found
7155 */
7156static inline const struct ieee80211_sta_he_cap *
7157ieee80211_get_he_iftype_cap_vif(const struct ieee80211_supported_band *sband,
7158 struct ieee80211_vif *vif)
7159{
7160 return ieee80211_get_he_iftype_cap(sband, ieee80211_vif_type_p2p(vif));
7161}
7162
7163/**
7164 * ieee80211_get_he_6ghz_capa_vif - return HE 6 GHz capabilities
7165 * @sband: the sband to search for the STA on
7166 * @vif: the vif to get the iftype from
7167 *
7168 * Return: the 6GHz capabilities
7169 */
7170static inline __le16
7171ieee80211_get_he_6ghz_capa_vif(const struct ieee80211_supported_band *sband,
7172 struct ieee80211_vif *vif)
7173{
7174 return ieee80211_get_he_6ghz_capa(sband, ieee80211_vif_type_p2p(vif));
7175}
7176
7177/**
7178 * ieee80211_get_eht_iftype_cap_vif - return ETH capabilities for sband/vif
7179 * @sband: the sband to search for the iftype on
7180 * @vif: the vif to get the iftype from
7181 *
7182 * Return: pointer to the struct ieee80211_sta_eht_cap, or %NULL is none found
7183 */
7184static inline const struct ieee80211_sta_eht_cap *
7185ieee80211_get_eht_iftype_cap_vif(const struct ieee80211_supported_band *sband,
7186 struct ieee80211_vif *vif)
7187{
7188 return ieee80211_get_eht_iftype_cap(sband, ieee80211_vif_type_p2p(vif));
7189}
7190
7191/**
7192 * ieee80211_update_mu_groups - set the VHT MU-MIMO groud data
7193 *
7194 * @vif: the specified virtual interface
7195 * @link_id: the link ID for MLO, otherwise 0
7196 * @membership: 64 bits array - a bit is set if station is member of the group
7197 * @position: 2 bits per group id indicating the position in the group
7198 *
7199 * Note: This function assumes that the given vif is valid and the position and
7200 * membership data is of the correct size and are in the same byte order as the
7201 * matching GroupId management frame.
7202 * Calls to this function need to be serialized with RX path.
7203 */
7204void ieee80211_update_mu_groups(struct ieee80211_vif *vif, unsigned int link_id,
7205 const u8 *membership, const u8 *position);
7206
7207void ieee80211_enable_rssi_reports(struct ieee80211_vif *vif,
7208 int rssi_min_thold,
7209 int rssi_max_thold);
7210
7211void ieee80211_disable_rssi_reports(struct ieee80211_vif *vif);
7212
7213/**
7214 * ieee80211_ave_rssi - report the average RSSI for the specified interface
7215 *
7216 * @vif: the specified virtual interface
7217 *
7218 * Note: This function assumes that the given vif is valid.
7219 *
7220 * Return: The average RSSI value for the requested interface, or 0 if not
7221 * applicable.
7222 */
7223int ieee80211_ave_rssi(struct ieee80211_vif *vif);
7224
7225/**
7226 * ieee80211_report_wowlan_wakeup - report WoWLAN wakeup
7227 * @vif: virtual interface
7228 * @wakeup: wakeup reason(s)
7229 * @gfp: allocation flags
7230 *
7231 * See cfg80211_report_wowlan_wakeup().
7232 */
7233void ieee80211_report_wowlan_wakeup(struct ieee80211_vif *vif,
7234 struct cfg80211_wowlan_wakeup *wakeup,
7235 gfp_t gfp);
7236
7237/**
7238 * ieee80211_tx_prepare_skb - prepare an 802.11 skb for transmission
7239 * @hw: pointer as obtained from ieee80211_alloc_hw()
7240 * @vif: virtual interface
7241 * @skb: frame to be sent from within the driver
7242 * @band: the band to transmit on
7243 * @sta: optional pointer to get the station to send the frame to
7244 *
7245 * Return: %true if the skb was prepared, %false otherwise
7246 *
7247 * Note: must be called under RCU lock
7248 */
7249bool ieee80211_tx_prepare_skb(struct ieee80211_hw *hw,
7250 struct ieee80211_vif *vif, struct sk_buff *skb,
7251 int band, struct ieee80211_sta **sta);
7252
7253/**
7254 * ieee80211_parse_tx_radiotap - Sanity-check and parse the radiotap header
7255 * of injected frames.
7256 *
7257 * To accurately parse and take into account rate and retransmission fields,
7258 * you must initialize the chandef field in the ieee80211_tx_info structure
7259 * of the skb before calling this function.
7260 *
7261 * @skb: packet injected by userspace
7262 * @dev: the &struct device of this 802.11 device
7263 *
7264 * Return: %true if the radiotap header was parsed, %false otherwise
7265 */
7266bool ieee80211_parse_tx_radiotap(struct sk_buff *skb,
7267 struct net_device *dev);
7268
7269/**
7270 * struct ieee80211_noa_data - holds temporary data for tracking P2P NoA state
7271 *
7272 * @next_tsf: TSF timestamp of the next absent state change
7273 * @has_next_tsf: next absent state change event pending
7274 *
7275 * @absent: descriptor bitmask, set if GO is currently absent
7276 *
7277 * private:
7278 *
7279 * @count: count fields from the NoA descriptors
7280 * @desc: adjusted data from the NoA
7281 */
7282struct ieee80211_noa_data {
7283 u32 next_tsf;
7284 bool has_next_tsf;
7285
7286 u8 absent;
7287
7288 u8 count[IEEE80211_P2P_NOA_DESC_MAX];
7289 struct {
7290 u32 start;
7291 u32 duration;
7292 u32 interval;
7293 } desc[IEEE80211_P2P_NOA_DESC_MAX];
7294};
7295
7296/**
7297 * ieee80211_parse_p2p_noa - initialize NoA tracking data from P2P IE
7298 *
7299 * @attr: P2P NoA IE
7300 * @data: NoA tracking data
7301 * @tsf: current TSF timestamp
7302 *
7303 * Return: number of successfully parsed descriptors
7304 */
7305int ieee80211_parse_p2p_noa(const struct ieee80211_p2p_noa_attr *attr,
7306 struct ieee80211_noa_data *data, u32 tsf);
7307
7308/**
7309 * ieee80211_update_p2p_noa - get next pending P2P GO absent state change
7310 *
7311 * @data: NoA tracking data
7312 * @tsf: current TSF timestamp
7313 */
7314void ieee80211_update_p2p_noa(struct ieee80211_noa_data *data, u32 tsf);
7315
7316/**
7317 * ieee80211_tdls_oper_request - request userspace to perform a TDLS operation
7318 * @vif: virtual interface
7319 * @peer: the peer's destination address
7320 * @oper: the requested TDLS operation
7321 * @reason_code: reason code for the operation, valid for TDLS teardown
7322 * @gfp: allocation flags
7323 *
7324 * See cfg80211_tdls_oper_request().
7325 */
7326void ieee80211_tdls_oper_request(struct ieee80211_vif *vif, const u8 *peer,
7327 enum nl80211_tdls_operation oper,
7328 u16 reason_code, gfp_t gfp);
7329
7330/**
7331 * ieee80211_reserve_tid - request to reserve a specific TID
7332 *
7333 * There is sometimes a need (such as in TDLS) for blocking the driver from
7334 * using a specific TID so that the FW can use it for certain operations such
7335 * as sending PTI requests. To make sure that the driver doesn't use that TID,
7336 * this function must be called as it flushes out packets on this TID and marks
7337 * it as blocked, so that any transmit for the station on this TID will be
7338 * redirected to the alternative TID in the same AC.
7339 *
7340 * Note that this function blocks and may call back into the driver, so it
7341 * should be called without driver locks held. Also note this function should
7342 * only be called from the driver's @sta_state callback.
7343 *
7344 * @sta: the station to reserve the TID for
7345 * @tid: the TID to reserve
7346 *
7347 * Returns: 0 on success, else on failure
7348 */
7349int ieee80211_reserve_tid(struct ieee80211_sta *sta, u8 tid);
7350
7351/**
7352 * ieee80211_unreserve_tid - request to unreserve a specific TID
7353 *
7354 * Once there is no longer any need for reserving a certain TID, this function
7355 * should be called, and no longer will packets have their TID modified for
7356 * preventing use of this TID in the driver.
7357 *
7358 * Note that this function blocks and acquires a lock, so it should be called
7359 * without driver locks held. Also note this function should only be called
7360 * from the driver's @sta_state callback.
7361 *
7362 * @sta: the station
7363 * @tid: the TID to unreserve
7364 */
7365void ieee80211_unreserve_tid(struct ieee80211_sta *sta, u8 tid);
7366
7367/**
7368 * ieee80211_tx_dequeue - dequeue a packet from a software tx queue
7369 *
7370 * @hw: pointer as obtained from ieee80211_alloc_hw()
7371 * @txq: pointer obtained from station or virtual interface, or from
7372 * ieee80211_next_txq()
7373 *
7374 * Return: the skb if successful, %NULL if no frame was available.
7375 *
7376 * Note that this must be called in an rcu_read_lock() critical section,
7377 * which can only be released after the SKB was handled. Some pointers in
7378 * skb->cb, e.g. the key pointer, are protected by RCU and thus the
7379 * critical section must persist not just for the duration of this call
7380 * but for the duration of the frame handling.
7381 * However, also note that while in the wake_tx_queue() method,
7382 * rcu_read_lock() is already held.
7383 *
7384 * softirqs must also be disabled when this function is called.
7385 * In process context, use ieee80211_tx_dequeue_ni() instead.
7386 */
7387struct sk_buff *ieee80211_tx_dequeue(struct ieee80211_hw *hw,
7388 struct ieee80211_txq *txq);
7389
7390/**
7391 * ieee80211_tx_dequeue_ni - dequeue a packet from a software tx queue
7392 * (in process context)
7393 *
7394 * Like ieee80211_tx_dequeue() but can be called in process context
7395 * (internally disables bottom halves).
7396 *
7397 * @hw: pointer as obtained from ieee80211_alloc_hw()
7398 * @txq: pointer obtained from station or virtual interface, or from
7399 * ieee80211_next_txq()
7400 *
7401 * Return: the skb if successful, %NULL if no frame was available.
7402 */
7403static inline struct sk_buff *ieee80211_tx_dequeue_ni(struct ieee80211_hw *hw,
7404 struct ieee80211_txq *txq)
7405{
7406 struct sk_buff *skb;
7407
7408 local_bh_disable();
7409 skb = ieee80211_tx_dequeue(hw, txq);
7410 local_bh_enable();
7411
7412 return skb;
7413}
7414
7415/**
7416 * ieee80211_handle_wake_tx_queue - mac80211 handler for wake_tx_queue callback
7417 *
7418 * @hw: pointer as obtained from wake_tx_queue() callback().
7419 * @txq: pointer as obtained from wake_tx_queue() callback().
7420 *
7421 * Drivers can use this function for the mandatory mac80211 wake_tx_queue
7422 * callback in struct ieee80211_ops. They should not call this function.
7423 */
7424void ieee80211_handle_wake_tx_queue(struct ieee80211_hw *hw,
7425 struct ieee80211_txq *txq);
7426
7427/**
7428 * ieee80211_next_txq - get next tx queue to pull packets from
7429 *
7430 * @hw: pointer as obtained from ieee80211_alloc_hw()
7431 * @ac: AC number to return packets from.
7432 *
7433 * Return: the next txq if successful, %NULL if no queue is eligible. If a txq
7434 * is returned, it should be returned with ieee80211_return_txq() after the
7435 * driver has finished scheduling it.
7436 */
7437struct ieee80211_txq *ieee80211_next_txq(struct ieee80211_hw *hw, u8 ac);
7438
7439/**
7440 * ieee80211_txq_schedule_start - start new scheduling round for TXQs
7441 *
7442 * @hw: pointer as obtained from ieee80211_alloc_hw()
7443 * @ac: AC number to acquire locks for
7444 *
7445 * Should be called before ieee80211_next_txq() or ieee80211_return_txq().
7446 * The driver must not call multiple TXQ scheduling rounds concurrently.
7447 */
7448void ieee80211_txq_schedule_start(struct ieee80211_hw *hw, u8 ac);
7449
7450/* (deprecated) */
7451static inline void ieee80211_txq_schedule_end(struct ieee80211_hw *hw, u8 ac)
7452{
7453}
7454
7455void __ieee80211_schedule_txq(struct ieee80211_hw *hw,
7456 struct ieee80211_txq *txq, bool force);
7457
7458/**
7459 * ieee80211_schedule_txq - schedule a TXQ for transmission
7460 *
7461 * @hw: pointer as obtained from ieee80211_alloc_hw()
7462 * @txq: pointer obtained from station or virtual interface
7463 *
7464 * Schedules a TXQ for transmission if it is not already scheduled,
7465 * even if mac80211 does not have any packets buffered.
7466 *
7467 * The driver may call this function if it has buffered packets for
7468 * this TXQ internally.
7469 */
7470static inline void
7471ieee80211_schedule_txq(struct ieee80211_hw *hw, struct ieee80211_txq *txq)
7472{
7473 __ieee80211_schedule_txq(hw, txq, true);
7474}
7475
7476/**
7477 * ieee80211_return_txq - return a TXQ previously acquired by ieee80211_next_txq()
7478 *
7479 * @hw: pointer as obtained from ieee80211_alloc_hw()
7480 * @txq: pointer obtained from station or virtual interface
7481 * @force: schedule txq even if mac80211 does not have any buffered packets.
7482 *
7483 * The driver may set force=true if it has buffered packets for this TXQ
7484 * internally.
7485 */
7486static inline void
7487ieee80211_return_txq(struct ieee80211_hw *hw, struct ieee80211_txq *txq,
7488 bool force)
7489{
7490 __ieee80211_schedule_txq(hw, txq, force);
7491}
7492
7493/**
7494 * ieee80211_txq_may_transmit - check whether TXQ is allowed to transmit
7495 *
7496 * This function is used to check whether given txq is allowed to transmit by
7497 * the airtime scheduler, and can be used by drivers to access the airtime
7498 * fairness accounting without using the scheduling order enforced by
7499 * next_txq().
7500 *
7501 * Returns %true if the airtime scheduler thinks the TXQ should be allowed to
7502 * transmit, and %false if it should be throttled. This function can also have
7503 * the side effect of rotating the TXQ in the scheduler rotation, which will
7504 * eventually bring the deficit to positive and allow the station to transmit
7505 * again.
7506 *
7507 * The API ieee80211_txq_may_transmit() also ensures that TXQ list will be
7508 * aligned against driver's own round-robin scheduler list. i.e it rotates
7509 * the TXQ list till it makes the requested node becomes the first entry
7510 * in TXQ list. Thus both the TXQ list and driver's list are in sync. If this
7511 * function returns %true, the driver is expected to schedule packets
7512 * for transmission, and then return the TXQ through ieee80211_return_txq().
7513 *
7514 * @hw: pointer as obtained from ieee80211_alloc_hw()
7515 * @txq: pointer obtained from station or virtual interface
7516 *
7517 * Return: %true if transmission is allowed, %false otherwise
7518 */
7519bool ieee80211_txq_may_transmit(struct ieee80211_hw *hw,
7520 struct ieee80211_txq *txq);
7521
7522/**
7523 * ieee80211_txq_get_depth - get pending frame/byte count of given txq
7524 *
7525 * The values are not guaranteed to be coherent with regard to each other, i.e.
7526 * txq state can change half-way of this function and the caller may end up
7527 * with "new" frame_cnt and "old" byte_cnt or vice-versa.
7528 *
7529 * @txq: pointer obtained from station or virtual interface
7530 * @frame_cnt: pointer to store frame count
7531 * @byte_cnt: pointer to store byte count
7532 */
7533void ieee80211_txq_get_depth(struct ieee80211_txq *txq,
7534 unsigned long *frame_cnt,
7535 unsigned long *byte_cnt);
7536
7537/**
7538 * ieee80211_nan_func_terminated - notify about NAN function termination.
7539 *
7540 * This function is used to notify mac80211 about NAN function termination.
7541 * Note that this function can't be called from hard irq.
7542 *
7543 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
7544 * @inst_id: the local instance id
7545 * @reason: termination reason (one of the NL80211_NAN_FUNC_TERM_REASON_*)
7546 * @gfp: allocation flags
7547 */
7548void ieee80211_nan_func_terminated(struct ieee80211_vif *vif,
7549 u8 inst_id,
7550 enum nl80211_nan_func_term_reason reason,
7551 gfp_t gfp);
7552
7553/**
7554 * ieee80211_nan_func_match - notify about NAN function match event.
7555 *
7556 * This function is used to notify mac80211 about NAN function match. The
7557 * cookie inside the match struct will be assigned by mac80211.
7558 * Note that this function can't be called from hard irq.
7559 *
7560 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
7561 * @match: match event information
7562 * @gfp: allocation flags
7563 */
7564void ieee80211_nan_func_match(struct ieee80211_vif *vif,
7565 struct cfg80211_nan_match_params *match,
7566 gfp_t gfp);
7567
7568/**
7569 * ieee80211_calc_rx_airtime - calculate estimated transmission airtime for RX.
7570 *
7571 * This function calculates the estimated airtime usage of a frame based on the
7572 * rate information in the RX status struct and the frame length.
7573 *
7574 * @hw: pointer as obtained from ieee80211_alloc_hw()
7575 * @status: &struct ieee80211_rx_status containing the transmission rate
7576 * information.
7577 * @len: frame length in bytes
7578 *
7579 * Return: the airtime estimate
7580 */
7581u32 ieee80211_calc_rx_airtime(struct ieee80211_hw *hw,
7582 struct ieee80211_rx_status *status,
7583 int len);
7584
7585/**
7586 * ieee80211_calc_tx_airtime - calculate estimated transmission airtime for TX.
7587 *
7588 * This function calculates the estimated airtime usage of a frame based on the
7589 * rate information in the TX info struct and the frame length.
7590 *
7591 * @hw: pointer as obtained from ieee80211_alloc_hw()
7592 * @info: &struct ieee80211_tx_info of the frame.
7593 * @len: frame length in bytes
7594 *
7595 * Return: the airtime estimate
7596 */
7597u32 ieee80211_calc_tx_airtime(struct ieee80211_hw *hw,
7598 struct ieee80211_tx_info *info,
7599 int len);
7600/**
7601 * ieee80211_get_fils_discovery_tmpl - Get FILS discovery template.
7602 * @hw: pointer obtained from ieee80211_alloc_hw().
7603 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
7604 *
7605 * The driver is responsible for freeing the returned skb.
7606 *
7607 * Return: FILS discovery template. %NULL on error.
7608 */
7609struct sk_buff *ieee80211_get_fils_discovery_tmpl(struct ieee80211_hw *hw,
7610 struct ieee80211_vif *vif);
7611
7612/**
7613 * ieee80211_get_unsol_bcast_probe_resp_tmpl - Get unsolicited broadcast
7614 * probe response template.
7615 * @hw: pointer obtained from ieee80211_alloc_hw().
7616 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
7617 *
7618 * The driver is responsible for freeing the returned skb.
7619 *
7620 * Return: Unsolicited broadcast probe response template. %NULL on error.
7621 */
7622struct sk_buff *
7623ieee80211_get_unsol_bcast_probe_resp_tmpl(struct ieee80211_hw *hw,
7624 struct ieee80211_vif *vif);
7625
7626/**
7627 * ieee80211_obss_color_collision_notify - notify userland about a BSS color
7628 * collision.
7629 * @link_id: valid link_id during MLO or 0 for non-MLO
7630 *
7631 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
7632 * @color_bitmap: a 64 bit bitmap representing the colors that the local BSS is
7633 * aware of.
7634 */
7635void
7636ieee80211_obss_color_collision_notify(struct ieee80211_vif *vif,
7637 u64 color_bitmap, u8 link_id);
7638
7639/**
7640 * ieee80211_is_tx_data - check if frame is a data frame
7641 *
7642 * The function is used to check if a frame is a data frame. Frames with
7643 * hardware encapsulation enabled are data frames.
7644 *
7645 * @skb: the frame to be transmitted.
7646 *
7647 * Return: %true if @skb is a data frame, %false otherwise
7648 */
7649static inline bool ieee80211_is_tx_data(struct sk_buff *skb)
7650{
7651 struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
7652 struct ieee80211_hdr *hdr = (void *) skb->data;
7653
7654 return info->flags & IEEE80211_TX_CTL_HW_80211_ENCAP ||
7655 ieee80211_is_data(hdr->frame_control);
7656}
7657
7658/**
7659 * ieee80211_set_active_links - set active links in client mode
7660 * @vif: interface to set active links on
7661 * @active_links: the new active links bitmap
7662 *
7663 * Context: Must be called with wiphy mutex held; may sleep; calls
7664 * back into the driver.
7665 *
7666 * This changes the active links on an interface. The interface
7667 * must be in client mode (in AP mode, all links are always active),
7668 * and @active_links must be a subset of the vif's valid_links.
7669 *
7670 * If a link is switched off and another is switched on at the same
7671 * time (e.g. active_links going from 0x1 to 0x10) then you will get
7672 * a sequence of calls like
7673 *
7674 * - change_vif_links(0x11)
7675 * - unassign_vif_chanctx(link_id=0)
7676 * - assign_vif_chanctx(link_id=4)
7677 * - change_sta_links(0x11) for each affected STA (the AP)
7678 * (TDLS connections on now inactive links should be torn down)
7679 * - remove group keys on the old link (link_id 0)
7680 * - add new group keys (GTK/IGTK/BIGTK) on the new link (link_id 4)
7681 * - change_sta_links(0x10) for each affected STA (the AP)
7682 * - change_vif_links(0x10)
7683 *
7684 * Return: 0 on success. An error code otherwise.
7685 */
7686int ieee80211_set_active_links(struct ieee80211_vif *vif, u16 active_links);
7687
7688/**
7689 * ieee80211_set_active_links_async - asynchronously set active links
7690 * @vif: interface to set active links on
7691 * @active_links: the new active links bitmap
7692 *
7693 * See ieee80211_set_active_links() for more information, the only
7694 * difference here is that the link change is triggered async and
7695 * can be called in any context, but the link switch will only be
7696 * completed after it returns.
7697 */
7698void ieee80211_set_active_links_async(struct ieee80211_vif *vif,
7699 u16 active_links);
7700
7701/**
7702 * ieee80211_send_teardown_neg_ttlm - tear down a negotiated TTLM request
7703 * @vif: the interface on which the tear down request should be sent.
7704 *
7705 * This function can be used to tear down a previously accepted negotiated
7706 * TTLM request.
7707 */
7708void ieee80211_send_teardown_neg_ttlm(struct ieee80211_vif *vif);
7709
7710/**
7711 * ieee80211_chan_width_to_rx_bw - convert channel width to STA RX bandwidth
7712 * @width: the channel width value to convert
7713 * Return: the STA RX bandwidth value for the channel width
7714 */
7715static inline enum ieee80211_sta_rx_bandwidth
7716ieee80211_chan_width_to_rx_bw(enum nl80211_chan_width width)
7717{
7718 switch (width) {
7719 default:
7720 WARN_ON_ONCE(1);
7721 fallthrough;
7722 case NL80211_CHAN_WIDTH_20_NOHT:
7723 case NL80211_CHAN_WIDTH_20:
7724 return IEEE80211_STA_RX_BW_20;
7725 case NL80211_CHAN_WIDTH_40:
7726 return IEEE80211_STA_RX_BW_40;
7727 case NL80211_CHAN_WIDTH_80:
7728 return IEEE80211_STA_RX_BW_80;
7729 case NL80211_CHAN_WIDTH_160:
7730 case NL80211_CHAN_WIDTH_80P80:
7731 return IEEE80211_STA_RX_BW_160;
7732 case NL80211_CHAN_WIDTH_320:
7733 return IEEE80211_STA_RX_BW_320;
7734 }
7735}
7736
7737/* for older drivers - let's not document these ... */
7738int ieee80211_emulate_add_chanctx(struct ieee80211_hw *hw,
7739 struct ieee80211_chanctx_conf *ctx);
7740void ieee80211_emulate_remove_chanctx(struct ieee80211_hw *hw,
7741 struct ieee80211_chanctx_conf *ctx);
7742void ieee80211_emulate_change_chanctx(struct ieee80211_hw *hw,
7743 struct ieee80211_chanctx_conf *ctx,
7744 u32 changed);
7745int ieee80211_emulate_switch_vif_chanctx(struct ieee80211_hw *hw,
7746 struct ieee80211_vif_chanctx_switch *vifs,
7747 int n_vifs,
7748 enum ieee80211_chanctx_switch_mode mode);
7749
7750#endif /* MAC80211_H */
1/* SPDX-License-Identifier: GPL-2.0-only */
2/*
3 * mac80211 <-> driver interface
4 *
5 * Copyright 2002-2005, Devicescape Software, Inc.
6 * Copyright 2006-2007 Jiri Benc <jbenc@suse.cz>
7 * Copyright 2007-2010 Johannes Berg <johannes@sipsolutions.net>
8 * Copyright 2013-2014 Intel Mobile Communications GmbH
9 * Copyright (C) 2015 - 2017 Intel Deutschland GmbH
10 * Copyright (C) 2018 - 2024 Intel Corporation
11 */
12
13#ifndef MAC80211_H
14#define MAC80211_H
15
16#include <linux/bug.h>
17#include <linux/kernel.h>
18#include <linux/if_ether.h>
19#include <linux/skbuff.h>
20#include <linux/ieee80211.h>
21#include <linux/lockdep.h>
22#include <net/cfg80211.h>
23#include <net/codel.h>
24#include <net/ieee80211_radiotap.h>
25#include <asm/unaligned.h>
26
27/**
28 * DOC: Introduction
29 *
30 * mac80211 is the Linux stack for 802.11 hardware that implements
31 * only partial functionality in hard- or firmware. This document
32 * defines the interface between mac80211 and low-level hardware
33 * drivers.
34 */
35
36/**
37 * DOC: Calling mac80211 from interrupts
38 *
39 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
40 * called in hardware interrupt context. The low-level driver must not call any
41 * other functions in hardware interrupt context. If there is a need for such
42 * call, the low-level driver should first ACK the interrupt and perform the
43 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
44 * tasklet function.
45 *
46 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
47 * use the non-IRQ-safe functions!
48 */
49
50/**
51 * DOC: Warning
52 *
53 * If you're reading this document and not the header file itself, it will
54 * be incomplete because not all documentation has been converted yet.
55 */
56
57/**
58 * DOC: Frame format
59 *
60 * As a general rule, when frames are passed between mac80211 and the driver,
61 * they start with the IEEE 802.11 header and include the same octets that are
62 * sent over the air except for the FCS which should be calculated by the
63 * hardware.
64 *
65 * There are, however, various exceptions to this rule for advanced features:
66 *
67 * The first exception is for hardware encryption and decryption offload
68 * where the IV/ICV may or may not be generated in hardware.
69 *
70 * Secondly, when the hardware handles fragmentation, the frame handed to
71 * the driver from mac80211 is the MSDU, not the MPDU.
72 */
73
74/**
75 * DOC: mac80211 workqueue
76 *
77 * mac80211 provides its own workqueue for drivers and internal mac80211 use.
78 * The workqueue is a single threaded workqueue and can only be accessed by
79 * helpers for sanity checking. Drivers must ensure all work added onto the
80 * mac80211 workqueue should be cancelled on the driver stop() callback.
81 *
82 * mac80211 will flush the workqueue upon interface removal and during
83 * suspend.
84 *
85 * All work performed on the mac80211 workqueue must not acquire the RTNL lock.
86 *
87 */
88
89/**
90 * DOC: mac80211 software tx queueing
91 *
92 * mac80211 uses an intermediate queueing implementation, designed to allow the
93 * driver to keep hardware queues short and to provide some fairness between
94 * different stations/interfaces.
95 *
96 * Drivers must provide the .wake_tx_queue driver operation by either
97 * linking it to ieee80211_handle_wake_tx_queue() or implementing a custom
98 * handler.
99 *
100 * Intermediate queues (struct ieee80211_txq) are kept per-sta per-tid, with
101 * another per-sta for non-data/non-mgmt and bufferable management frames, and
102 * a single per-vif queue for multicast data frames.
103 *
104 * The driver is expected to initialize its private per-queue data for stations
105 * and interfaces in the .add_interface and .sta_add ops.
106 *
107 * The driver can't access the internal TX queues (iTXQs) directly.
108 * Whenever mac80211 adds a new frame to a queue, it calls the .wake_tx_queue
109 * driver op.
110 * Drivers implementing a custom .wake_tx_queue op can get them by calling
111 * ieee80211_tx_dequeue(). Drivers using ieee80211_handle_wake_tx_queue() will
112 * simply get the individual frames pushed via the .tx driver operation.
113 *
114 * Drivers can optionally delegate responsibility for scheduling queues to
115 * mac80211, to take advantage of airtime fairness accounting. In this case, to
116 * obtain the next queue to pull frames from, the driver calls
117 * ieee80211_next_txq(). The driver is then expected to return the txq using
118 * ieee80211_return_txq().
119 *
120 * For AP powersave TIM handling, the driver only needs to indicate if it has
121 * buffered packets in the driver specific data structures by calling
122 * ieee80211_sta_set_buffered(). For frames buffered in the ieee80211_txq
123 * struct, mac80211 sets the appropriate TIM PVB bits and calls
124 * .release_buffered_frames().
125 * In that callback the driver is therefore expected to release its own
126 * buffered frames and afterwards also frames from the ieee80211_txq (obtained
127 * via the usual ieee80211_tx_dequeue).
128 */
129
130/**
131 * DOC: HW timestamping
132 *
133 * Timing Measurement and Fine Timing Measurement require accurate timestamps
134 * of the action frames TX/RX and their respective acks.
135 *
136 * To report hardware timestamps for Timing Measurement or Fine Timing
137 * Measurement frame RX, the low level driver should set the SKB's hwtstamp
138 * field to the frame RX timestamp and report the ack TX timestamp in the
139 * ieee80211_rx_status struct.
140 *
141 * Similarly, to report hardware timestamps for Timing Measurement or Fine
142 * Timing Measurement frame TX, the driver should set the SKB's hwtstamp field
143 * to the frame TX timestamp and report the ack RX timestamp in the
144 * ieee80211_tx_status struct.
145 */
146struct device;
147
148/**
149 * enum ieee80211_max_queues - maximum number of queues
150 *
151 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
152 * @IEEE80211_MAX_QUEUE_MAP: bitmap with maximum queues set
153 */
154enum ieee80211_max_queues {
155 IEEE80211_MAX_QUEUES = 16,
156 IEEE80211_MAX_QUEUE_MAP = BIT(IEEE80211_MAX_QUEUES) - 1,
157};
158
159#define IEEE80211_INVAL_HW_QUEUE 0xff
160
161/**
162 * enum ieee80211_ac_numbers - AC numbers as used in mac80211
163 * @IEEE80211_AC_VO: voice
164 * @IEEE80211_AC_VI: video
165 * @IEEE80211_AC_BE: best effort
166 * @IEEE80211_AC_BK: background
167 */
168enum ieee80211_ac_numbers {
169 IEEE80211_AC_VO = 0,
170 IEEE80211_AC_VI = 1,
171 IEEE80211_AC_BE = 2,
172 IEEE80211_AC_BK = 3,
173};
174
175/**
176 * struct ieee80211_tx_queue_params - transmit queue configuration
177 *
178 * The information provided in this structure is required for QoS
179 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
180 *
181 * @aifs: arbitration interframe space [0..255]
182 * @cw_min: minimum contention window [a value of the form
183 * 2^n-1 in the range 1..32767]
184 * @cw_max: maximum contention window [like @cw_min]
185 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
186 * @acm: is mandatory admission control required for the access category
187 * @uapsd: is U-APSD mode enabled for the queue
188 * @mu_edca: is the MU EDCA configured
189 * @mu_edca_param_rec: MU EDCA Parameter Record for HE
190 */
191struct ieee80211_tx_queue_params {
192 u16 txop;
193 u16 cw_min;
194 u16 cw_max;
195 u8 aifs;
196 bool acm;
197 bool uapsd;
198 bool mu_edca;
199 struct ieee80211_he_mu_edca_param_ac_rec mu_edca_param_rec;
200};
201
202struct ieee80211_low_level_stats {
203 unsigned int dot11ACKFailureCount;
204 unsigned int dot11RTSFailureCount;
205 unsigned int dot11FCSErrorCount;
206 unsigned int dot11RTSSuccessCount;
207};
208
209/**
210 * enum ieee80211_chanctx_change - change flag for channel context
211 * @IEEE80211_CHANCTX_CHANGE_WIDTH: The channel width changed
212 * @IEEE80211_CHANCTX_CHANGE_RX_CHAINS: The number of RX chains changed
213 * @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed
214 * @IEEE80211_CHANCTX_CHANGE_CHANNEL: switched to another operating channel,
215 * this is used only with channel switching with CSA
216 * @IEEE80211_CHANCTX_CHANGE_MIN_WIDTH: The min required channel width changed
217 * @IEEE80211_CHANCTX_CHANGE_AP: The AP channel definition changed, so (wider
218 * bandwidth) OFDMA settings need to be changed
219 * @IEEE80211_CHANCTX_CHANGE_PUNCTURING: The punctured channel(s) bitmap
220 * was changed.
221 */
222enum ieee80211_chanctx_change {
223 IEEE80211_CHANCTX_CHANGE_WIDTH = BIT(0),
224 IEEE80211_CHANCTX_CHANGE_RX_CHAINS = BIT(1),
225 IEEE80211_CHANCTX_CHANGE_RADAR = BIT(2),
226 IEEE80211_CHANCTX_CHANGE_CHANNEL = BIT(3),
227 IEEE80211_CHANCTX_CHANGE_MIN_WIDTH = BIT(4),
228 IEEE80211_CHANCTX_CHANGE_AP = BIT(5),
229 IEEE80211_CHANCTX_CHANGE_PUNCTURING = BIT(6),
230};
231
232/**
233 * struct ieee80211_chan_req - A channel "request"
234 * @oper: channel definition to use for operation
235 * @ap: the channel definition of the AP, if any
236 * (otherwise the chan member is %NULL)
237 */
238struct ieee80211_chan_req {
239 struct cfg80211_chan_def oper;
240 struct cfg80211_chan_def ap;
241};
242
243/**
244 * struct ieee80211_chanctx_conf - channel context that vifs may be tuned to
245 *
246 * This is the driver-visible part. The ieee80211_chanctx
247 * that contains it is visible in mac80211 only.
248 *
249 * @def: the channel definition
250 * @min_def: the minimum channel definition currently required.
251 * @ap: the channel definition the AP actually is operating as,
252 * for use with (wider bandwidth) OFDMA
253 * @rx_chains_static: The number of RX chains that must always be
254 * active on the channel to receive MIMO transmissions
255 * @rx_chains_dynamic: The number of RX chains that must be enabled
256 * after RTS/CTS handshake to receive SMPS MIMO transmissions;
257 * this will always be >= @rx_chains_static.
258 * @radar_enabled: whether radar detection is enabled on this channel.
259 * @drv_priv: data area for driver use, will always be aligned to
260 * sizeof(void *), size is determined in hw information.
261 */
262struct ieee80211_chanctx_conf {
263 struct cfg80211_chan_def def;
264 struct cfg80211_chan_def min_def;
265 struct cfg80211_chan_def ap;
266
267 u8 rx_chains_static, rx_chains_dynamic;
268
269 bool radar_enabled;
270
271 u8 drv_priv[] __aligned(sizeof(void *));
272};
273
274/**
275 * enum ieee80211_chanctx_switch_mode - channel context switch mode
276 * @CHANCTX_SWMODE_REASSIGN_VIF: Both old and new contexts already
277 * exist (and will continue to exist), but the virtual interface
278 * needs to be switched from one to the other.
279 * @CHANCTX_SWMODE_SWAP_CONTEXTS: The old context exists but will stop
280 * to exist with this call, the new context doesn't exist but
281 * will be active after this call, the virtual interface switches
282 * from the old to the new (note that the driver may of course
283 * implement this as an on-the-fly chandef switch of the existing
284 * hardware context, but the mac80211 pointer for the old context
285 * will cease to exist and only the new one will later be used
286 * for changes/removal.)
287 */
288enum ieee80211_chanctx_switch_mode {
289 CHANCTX_SWMODE_REASSIGN_VIF,
290 CHANCTX_SWMODE_SWAP_CONTEXTS,
291};
292
293/**
294 * struct ieee80211_vif_chanctx_switch - vif chanctx switch information
295 *
296 * This is structure is used to pass information about a vif that
297 * needs to switch from one chanctx to another. The
298 * &ieee80211_chanctx_switch_mode defines how the switch should be
299 * done.
300 *
301 * @vif: the vif that should be switched from old_ctx to new_ctx
302 * @link_conf: the link conf that's switching
303 * @old_ctx: the old context to which the vif was assigned
304 * @new_ctx: the new context to which the vif must be assigned
305 */
306struct ieee80211_vif_chanctx_switch {
307 struct ieee80211_vif *vif;
308 struct ieee80211_bss_conf *link_conf;
309 struct ieee80211_chanctx_conf *old_ctx;
310 struct ieee80211_chanctx_conf *new_ctx;
311};
312
313/**
314 * enum ieee80211_bss_change - BSS change notification flags
315 *
316 * These flags are used with the bss_info_changed(), link_info_changed()
317 * and vif_cfg_changed() callbacks to indicate which parameter(s) changed.
318 *
319 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
320 * also implies a change in the AID.
321 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
322 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
323 * @BSS_CHANGED_ERP_SLOT: slot timing changed
324 * @BSS_CHANGED_HT: 802.11n parameters changed
325 * @BSS_CHANGED_BASIC_RATES: Basic rateset changed
326 * @BSS_CHANGED_BEACON_INT: Beacon interval changed
327 * @BSS_CHANGED_BSSID: BSSID changed, for whatever
328 * reason (IBSS and managed mode)
329 * @BSS_CHANGED_BEACON: Beacon data changed, retrieve
330 * new beacon (beaconing modes)
331 * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
332 * enabled/disabled (beaconing modes)
333 * @BSS_CHANGED_CQM: Connection quality monitor config changed
334 * @BSS_CHANGED_IBSS: IBSS join status changed
335 * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed.
336 * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note
337 * that it is only ever disabled for station mode.
338 * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface.
339 * @BSS_CHANGED_SSID: SSID changed for this BSS (AP and IBSS mode)
340 * @BSS_CHANGED_AP_PROBE_RESP: Probe Response changed for this BSS (AP mode)
341 * @BSS_CHANGED_PS: PS changed for this BSS (STA mode)
342 * @BSS_CHANGED_TXPOWER: TX power setting changed for this interface
343 * @BSS_CHANGED_P2P_PS: P2P powersave settings (CTWindow, opportunistic PS)
344 * changed
345 * @BSS_CHANGED_BEACON_INFO: Data from the AP's beacon became available:
346 * currently dtim_period only is under consideration.
347 * @BSS_CHANGED_BANDWIDTH: The bandwidth used by this interface changed,
348 * note that this is only called when it changes after the channel
349 * context had been assigned.
350 * @BSS_CHANGED_OCB: OCB join status changed
351 * @BSS_CHANGED_MU_GROUPS: VHT MU-MIMO group id or user position changed
352 * @BSS_CHANGED_KEEP_ALIVE: keep alive options (idle period or protected
353 * keep alive) changed.
354 * @BSS_CHANGED_MCAST_RATE: Multicast Rate setting changed for this interface
355 * @BSS_CHANGED_FTM_RESPONDER: fine timing measurement request responder
356 * functionality changed for this BSS (AP mode).
357 * @BSS_CHANGED_TWT: TWT status changed
358 * @BSS_CHANGED_HE_OBSS_PD: OBSS Packet Detection status changed.
359 * @BSS_CHANGED_HE_BSS_COLOR: BSS Color has changed
360 * @BSS_CHANGED_FILS_DISCOVERY: FILS discovery status changed.
361 * @BSS_CHANGED_UNSOL_BCAST_PROBE_RESP: Unsolicited broadcast probe response
362 * status changed.
363 * @BSS_CHANGED_MLD_VALID_LINKS: MLD valid links status changed.
364 * @BSS_CHANGED_MLD_TTLM: TID to link mapping was changed
365 */
366enum ieee80211_bss_change {
367 BSS_CHANGED_ASSOC = 1<<0,
368 BSS_CHANGED_ERP_CTS_PROT = 1<<1,
369 BSS_CHANGED_ERP_PREAMBLE = 1<<2,
370 BSS_CHANGED_ERP_SLOT = 1<<3,
371 BSS_CHANGED_HT = 1<<4,
372 BSS_CHANGED_BASIC_RATES = 1<<5,
373 BSS_CHANGED_BEACON_INT = 1<<6,
374 BSS_CHANGED_BSSID = 1<<7,
375 BSS_CHANGED_BEACON = 1<<8,
376 BSS_CHANGED_BEACON_ENABLED = 1<<9,
377 BSS_CHANGED_CQM = 1<<10,
378 BSS_CHANGED_IBSS = 1<<11,
379 BSS_CHANGED_ARP_FILTER = 1<<12,
380 BSS_CHANGED_QOS = 1<<13,
381 BSS_CHANGED_IDLE = 1<<14,
382 BSS_CHANGED_SSID = 1<<15,
383 BSS_CHANGED_AP_PROBE_RESP = 1<<16,
384 BSS_CHANGED_PS = 1<<17,
385 BSS_CHANGED_TXPOWER = 1<<18,
386 BSS_CHANGED_P2P_PS = 1<<19,
387 BSS_CHANGED_BEACON_INFO = 1<<20,
388 BSS_CHANGED_BANDWIDTH = 1<<21,
389 BSS_CHANGED_OCB = 1<<22,
390 BSS_CHANGED_MU_GROUPS = 1<<23,
391 BSS_CHANGED_KEEP_ALIVE = 1<<24,
392 BSS_CHANGED_MCAST_RATE = 1<<25,
393 BSS_CHANGED_FTM_RESPONDER = 1<<26,
394 BSS_CHANGED_TWT = 1<<27,
395 BSS_CHANGED_HE_OBSS_PD = 1<<28,
396 BSS_CHANGED_HE_BSS_COLOR = 1<<29,
397 BSS_CHANGED_FILS_DISCOVERY = 1<<30,
398 BSS_CHANGED_UNSOL_BCAST_PROBE_RESP = 1<<31,
399 BSS_CHANGED_MLD_VALID_LINKS = BIT_ULL(33),
400 BSS_CHANGED_MLD_TTLM = BIT_ULL(34),
401
402 /* when adding here, make sure to change ieee80211_reconfig */
403};
404
405/*
406 * The maximum number of IPv4 addresses listed for ARP filtering. If the number
407 * of addresses for an interface increase beyond this value, hardware ARP
408 * filtering will be disabled.
409 */
410#define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4
411
412/**
413 * enum ieee80211_event_type - event to be notified to the low level driver
414 * @RSSI_EVENT: AP's rssi crossed the a threshold set by the driver.
415 * @MLME_EVENT: event related to MLME
416 * @BAR_RX_EVENT: a BAR was received
417 * @BA_FRAME_TIMEOUT: Frames were released from the reordering buffer because
418 * they timed out. This won't be called for each frame released, but only
419 * once each time the timeout triggers.
420 */
421enum ieee80211_event_type {
422 RSSI_EVENT,
423 MLME_EVENT,
424 BAR_RX_EVENT,
425 BA_FRAME_TIMEOUT,
426};
427
428/**
429 * enum ieee80211_rssi_event_data - relevant when event type is %RSSI_EVENT
430 * @RSSI_EVENT_HIGH: AP's rssi went below the threshold set by the driver.
431 * @RSSI_EVENT_LOW: AP's rssi went above the threshold set by the driver.
432 */
433enum ieee80211_rssi_event_data {
434 RSSI_EVENT_HIGH,
435 RSSI_EVENT_LOW,
436};
437
438/**
439 * struct ieee80211_rssi_event - data attached to an %RSSI_EVENT
440 * @data: See &enum ieee80211_rssi_event_data
441 */
442struct ieee80211_rssi_event {
443 enum ieee80211_rssi_event_data data;
444};
445
446/**
447 * enum ieee80211_mlme_event_data - relevant when event type is %MLME_EVENT
448 * @AUTH_EVENT: the MLME operation is authentication
449 * @ASSOC_EVENT: the MLME operation is association
450 * @DEAUTH_RX_EVENT: deauth received..
451 * @DEAUTH_TX_EVENT: deauth sent.
452 */
453enum ieee80211_mlme_event_data {
454 AUTH_EVENT,
455 ASSOC_EVENT,
456 DEAUTH_RX_EVENT,
457 DEAUTH_TX_EVENT,
458};
459
460/**
461 * enum ieee80211_mlme_event_status - relevant when event type is %MLME_EVENT
462 * @MLME_SUCCESS: the MLME operation completed successfully.
463 * @MLME_DENIED: the MLME operation was denied by the peer.
464 * @MLME_TIMEOUT: the MLME operation timed out.
465 */
466enum ieee80211_mlme_event_status {
467 MLME_SUCCESS,
468 MLME_DENIED,
469 MLME_TIMEOUT,
470};
471
472/**
473 * struct ieee80211_mlme_event - data attached to an %MLME_EVENT
474 * @data: See &enum ieee80211_mlme_event_data
475 * @status: See &enum ieee80211_mlme_event_status
476 * @reason: the reason code if applicable
477 */
478struct ieee80211_mlme_event {
479 enum ieee80211_mlme_event_data data;
480 enum ieee80211_mlme_event_status status;
481 u16 reason;
482};
483
484/**
485 * struct ieee80211_ba_event - data attached for BlockAck related events
486 * @sta: pointer to the &ieee80211_sta to which this event relates
487 * @tid: the tid
488 * @ssn: the starting sequence number (for %BAR_RX_EVENT)
489 */
490struct ieee80211_ba_event {
491 struct ieee80211_sta *sta;
492 u16 tid;
493 u16 ssn;
494};
495
496/**
497 * struct ieee80211_event - event to be sent to the driver
498 * @type: The event itself. See &enum ieee80211_event_type.
499 * @u.rssi: relevant if &type is %RSSI_EVENT
500 * @u.mlme: relevant if &type is %AUTH_EVENT
501 * @u.ba: relevant if &type is %BAR_RX_EVENT or %BA_FRAME_TIMEOUT
502 * @u:union holding the fields above
503 */
504struct ieee80211_event {
505 enum ieee80211_event_type type;
506 union {
507 struct ieee80211_rssi_event rssi;
508 struct ieee80211_mlme_event mlme;
509 struct ieee80211_ba_event ba;
510 } u;
511};
512
513/**
514 * struct ieee80211_mu_group_data - STA's VHT MU-MIMO group data
515 *
516 * This structure describes the group id data of VHT MU-MIMO
517 *
518 * @membership: 64 bits array - a bit is set if station is member of the group
519 * @position: 2 bits per group id indicating the position in the group
520 */
521struct ieee80211_mu_group_data {
522 u8 membership[WLAN_MEMBERSHIP_LEN];
523 u8 position[WLAN_USER_POSITION_LEN];
524};
525
526/**
527 * struct ieee80211_ftm_responder_params - FTM responder parameters
528 *
529 * @lci: LCI subelement content
530 * @civicloc: CIVIC location subelement content
531 * @lci_len: LCI data length
532 * @civicloc_len: Civic data length
533 */
534struct ieee80211_ftm_responder_params {
535 const u8 *lci;
536 const u8 *civicloc;
537 size_t lci_len;
538 size_t civicloc_len;
539};
540
541/**
542 * struct ieee80211_fils_discovery - FILS discovery parameters from
543 * IEEE Std 802.11ai-2016, Annex C.3 MIB detail.
544 *
545 * @min_interval: Minimum packet interval in TUs (0 - 10000)
546 * @max_interval: Maximum packet interval in TUs (0 - 10000)
547 */
548struct ieee80211_fils_discovery {
549 u32 min_interval;
550 u32 max_interval;
551};
552
553/**
554 * struct ieee80211_bss_conf - holds the BSS's changing parameters
555 *
556 * This structure keeps information about a BSS (and an association
557 * to that BSS) that can change during the lifetime of the BSS.
558 *
559 * @vif: reference to owning VIF
560 * @bss: the cfg80211 bss descriptor. Valid only for a station, and only
561 * when associated. Note: This contains information which is not
562 * necessarily authenticated. For example, information coming from probe
563 * responses.
564 * @addr: (link) address used locally
565 * @link_id: link ID, or 0 for non-MLO
566 * @htc_trig_based_pkt_ext: default PE in 4us units, if BSS supports HE
567 * @uora_exists: is the UORA element advertised by AP
568 * @uora_ocw_range: UORA element's OCW Range field
569 * @frame_time_rts_th: HE duration RTS threshold, in units of 32us
570 * @he_support: does this BSS support HE
571 * @twt_requester: does this BSS support TWT requester (relevant for managed
572 * mode only, set if the AP advertises TWT responder role)
573 * @twt_responder: does this BSS support TWT requester (relevant for managed
574 * mode only, set if the AP advertises TWT responder role)
575 * @twt_protected: does this BSS support protected TWT frames
576 * @twt_broadcast: does this BSS support broadcast TWT
577 * @use_cts_prot: use CTS protection
578 * @use_short_preamble: use 802.11b short preamble
579 * @use_short_slot: use short slot time (only relevant for ERP)
580 * @dtim_period: num of beacons before the next DTIM, for beaconing,
581 * valid in station mode only if after the driver was notified
582 * with the %BSS_CHANGED_BEACON_INFO flag, will be non-zero then.
583 * @sync_tsf: last beacon's/probe response's TSF timestamp (could be old
584 * as it may have been received during scanning long ago). If the
585 * HW flag %IEEE80211_HW_TIMING_BEACON_ONLY is set, then this can
586 * only come from a beacon, but might not become valid until after
587 * association when a beacon is received (which is notified with the
588 * %BSS_CHANGED_DTIM flag.). See also sync_dtim_count important notice.
589 * @sync_device_ts: the device timestamp corresponding to the sync_tsf,
590 * the driver/device can use this to calculate synchronisation
591 * (see @sync_tsf). See also sync_dtim_count important notice.
592 * @sync_dtim_count: Only valid when %IEEE80211_HW_TIMING_BEACON_ONLY
593 * is requested, see @sync_tsf/@sync_device_ts.
594 * IMPORTANT: These three sync_* parameters would possibly be out of sync
595 * by the time the driver will use them. The synchronized view is currently
596 * guaranteed only in certain callbacks.
597 * Note also that this is not used with MLD associations, mac80211 doesn't
598 * know how to track beacons for all of the links for this.
599 * @beacon_int: beacon interval
600 * @assoc_capability: capabilities taken from assoc resp
601 * @basic_rates: bitmap of basic rates, each bit stands for an
602 * index into the rate table configured by the driver in
603 * the current band.
604 * @beacon_rate: associated AP's beacon TX rate
605 * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
606 * @bssid: The BSSID for this BSS
607 * @enable_beacon: whether beaconing should be enabled or not
608 * @chanreq: Channel request for this BSS -- the hardware might be
609 * configured a higher bandwidth than this BSS uses, for example.
610 * @mu_group: VHT MU-MIMO group membership data
611 * @ht_operation_mode: HT operation mode like in &struct ieee80211_ht_operation.
612 * This field is only valid when the channel is a wide HT/VHT channel.
613 * Note that with TDLS this can be the case (channel is HT, protection must
614 * be used from this field) even when the BSS association isn't using HT.
615 * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
616 * implies disabled. As with the cfg80211 callback, a change here should
617 * cause an event to be sent indicating where the current value is in
618 * relation to the newly configured threshold.
619 * @cqm_rssi_low: Connection quality monitor RSSI lower threshold, a zero value
620 * implies disabled. This is an alternative mechanism to the single
621 * threshold event and can't be enabled simultaneously with it.
622 * @cqm_rssi_high: Connection quality monitor RSSI upper threshold.
623 * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis
624 * @qos: This is a QoS-enabled BSS.
625 * @hidden_ssid: The SSID of the current vif is hidden. Only valid in AP-mode.
626 * @txpower: TX power in dBm. INT_MIN means not configured.
627 * @txpower_type: TX power adjustment used to control per packet Transmit
628 * Power Control (TPC) in lower driver for the current vif. In particular
629 * TPC is enabled if value passed in %txpower_type is
630 * NL80211_TX_POWER_LIMITED (allow using less than specified from
631 * userspace), whereas TPC is disabled if %txpower_type is set to
632 * NL80211_TX_POWER_FIXED (use value configured from userspace)
633 * @p2p_noa_attr: P2P NoA attribute for P2P powersave
634 * @allow_p2p_go_ps: indication for AP or P2P GO interface, whether it's allowed
635 * to use P2P PS mechanism or not. AP/P2P GO is not allowed to use P2P PS
636 * if it has associated clients without P2P PS support.
637 * @max_idle_period: the time period during which the station can refrain from
638 * transmitting frames to its associated AP without being disassociated.
639 * In units of 1000 TUs. Zero value indicates that the AP did not include
640 * a (valid) BSS Max Idle Period Element.
641 * @protected_keep_alive: if set, indicates that the station should send an RSN
642 * protected frame to the AP to reset the idle timer at the AP for the
643 * station.
644 * @ftm_responder: whether to enable or disable fine timing measurement FTM
645 * responder functionality.
646 * @ftmr_params: configurable lci/civic parameter when enabling FTM responder.
647 * @nontransmitted: this BSS is a nontransmitted BSS profile
648 * @transmitter_bssid: the address of transmitter AP
649 * @bssid_index: index inside the multiple BSSID set
650 * @bssid_indicator: 2^bssid_indicator is the maximum number of APs in set
651 * @ema_ap: AP supports enhancements of discovery and advertisement of
652 * nontransmitted BSSIDs
653 * @profile_periodicity: the least number of beacon frames need to be received
654 * in order to discover all the nontransmitted BSSIDs in the set.
655 * @he_oper: HE operation information of the BSS (AP/Mesh) or of the AP we are
656 * connected to (STA)
657 * @he_obss_pd: OBSS Packet Detection parameters.
658 * @he_bss_color: BSS coloring settings, if BSS supports HE
659 * @fils_discovery: FILS discovery configuration
660 * @unsol_bcast_probe_resp_interval: Unsolicited broadcast probe response
661 * interval.
662 * @beacon_tx_rate: The configured beacon transmit rate that needs to be passed
663 * to driver when rate control is offloaded to firmware.
664 * @power_type: power type of BSS for 6 GHz
665 * @tx_pwr_env: transmit power envelope array of BSS.
666 * @tx_pwr_env_num: number of @tx_pwr_env.
667 * @pwr_reduction: power constraint of BSS.
668 * @eht_support: does this BSS support EHT
669 * @csa_active: marks whether a channel switch is going on.
670 * @mu_mimo_owner: indicates interface owns MU-MIMO capability
671 * @chanctx_conf: The channel context this interface is assigned to, or %NULL
672 * when it is not assigned. This pointer is RCU-protected due to the TX
673 * path needing to access it; even though the netdev carrier will always
674 * be off when it is %NULL there can still be races and packets could be
675 * processed after it switches back to %NULL.
676 * @color_change_active: marks whether a color change is ongoing.
677 * @color_change_color: the bss color that will be used after the change.
678 * @ht_ldpc: in AP mode, indicates interface has HT LDPC capability.
679 * @vht_ldpc: in AP mode, indicates interface has VHT LDPC capability.
680 * @he_ldpc: in AP mode, indicates interface has HE LDPC capability.
681 * @vht_su_beamformer: in AP mode, does this BSS support operation as an VHT SU
682 * beamformer
683 * @vht_su_beamformee: in AP mode, does this BSS support operation as an VHT SU
684 * beamformee
685 * @vht_mu_beamformer: in AP mode, does this BSS support operation as an VHT MU
686 * beamformer
687 * @vht_mu_beamformee: in AP mode, does this BSS support operation as an VHT MU
688 * beamformee
689 * @he_su_beamformer: in AP-mode, does this BSS support operation as an HE SU
690 * beamformer
691 * @he_su_beamformee: in AP-mode, does this BSS support operation as an HE SU
692 * beamformee
693 * @he_mu_beamformer: in AP-mode, does this BSS support operation as an HE MU
694 * beamformer
695 * @he_full_ul_mumimo: does this BSS support the reception (AP) or transmission
696 * (non-AP STA) of an HE TB PPDU on an RU that spans the entire PPDU
697 * bandwidth
698 * @eht_su_beamformer: in AP-mode, does this BSS enable operation as an EHT SU
699 * beamformer
700 * @eht_su_beamformee: in AP-mode, does this BSS enable operation as an EHT SU
701 * beamformee
702 * @eht_mu_beamformer: in AP-mode, does this BSS enable operation as an EHT MU
703 * beamformer
704 */
705struct ieee80211_bss_conf {
706 struct ieee80211_vif *vif;
707 struct cfg80211_bss *bss;
708
709 const u8 *bssid;
710 unsigned int link_id;
711 u8 addr[ETH_ALEN] __aligned(2);
712 u8 htc_trig_based_pkt_ext;
713 bool uora_exists;
714 u8 uora_ocw_range;
715 u16 frame_time_rts_th;
716 bool he_support;
717 bool twt_requester;
718 bool twt_responder;
719 bool twt_protected;
720 bool twt_broadcast;
721 /* erp related data */
722 bool use_cts_prot;
723 bool use_short_preamble;
724 bool use_short_slot;
725 bool enable_beacon;
726 u8 dtim_period;
727 u16 beacon_int;
728 u16 assoc_capability;
729 u64 sync_tsf;
730 u32 sync_device_ts;
731 u8 sync_dtim_count;
732 u32 basic_rates;
733 struct ieee80211_rate *beacon_rate;
734 int mcast_rate[NUM_NL80211_BANDS];
735 u16 ht_operation_mode;
736 s32 cqm_rssi_thold;
737 u32 cqm_rssi_hyst;
738 s32 cqm_rssi_low;
739 s32 cqm_rssi_high;
740 struct ieee80211_chan_req chanreq;
741 struct ieee80211_mu_group_data mu_group;
742 bool qos;
743 bool hidden_ssid;
744 int txpower;
745 enum nl80211_tx_power_setting txpower_type;
746 struct ieee80211_p2p_noa_attr p2p_noa_attr;
747 bool allow_p2p_go_ps;
748 u16 max_idle_period;
749 bool protected_keep_alive;
750 bool ftm_responder;
751 struct ieee80211_ftm_responder_params *ftmr_params;
752 /* Multiple BSSID data */
753 bool nontransmitted;
754 u8 transmitter_bssid[ETH_ALEN];
755 u8 bssid_index;
756 u8 bssid_indicator;
757 bool ema_ap;
758 u8 profile_periodicity;
759 struct {
760 u32 params;
761 u16 nss_set;
762 } he_oper;
763 struct ieee80211_he_obss_pd he_obss_pd;
764 struct cfg80211_he_bss_color he_bss_color;
765 struct ieee80211_fils_discovery fils_discovery;
766 u32 unsol_bcast_probe_resp_interval;
767 struct cfg80211_bitrate_mask beacon_tx_rate;
768 enum ieee80211_ap_reg_power power_type;
769 struct ieee80211_tx_pwr_env tx_pwr_env[IEEE80211_TPE_MAX_IE_COUNT];
770 u8 tx_pwr_env_num;
771 u8 pwr_reduction;
772 bool eht_support;
773
774 bool csa_active;
775
776 bool mu_mimo_owner;
777 struct ieee80211_chanctx_conf __rcu *chanctx_conf;
778
779 bool color_change_active;
780 u8 color_change_color;
781
782 bool ht_ldpc;
783 bool vht_ldpc;
784 bool he_ldpc;
785 bool vht_su_beamformer;
786 bool vht_su_beamformee;
787 bool vht_mu_beamformer;
788 bool vht_mu_beamformee;
789 bool he_su_beamformer;
790 bool he_su_beamformee;
791 bool he_mu_beamformer;
792 bool he_full_ul_mumimo;
793 bool eht_su_beamformer;
794 bool eht_su_beamformee;
795 bool eht_mu_beamformer;
796};
797
798/**
799 * enum mac80211_tx_info_flags - flags to describe transmission information/status
800 *
801 * These flags are used with the @flags member of &ieee80211_tx_info.
802 *
803 * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame.
804 * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
805 * number to this frame, taking care of not overwriting the fragment
806 * number and increasing the sequence number only when the
807 * IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
808 * assign sequence numbers to QoS-data frames but cannot do so correctly
809 * for non-QoS-data and management frames because beacons need them from
810 * that counter as well and mac80211 cannot guarantee proper sequencing.
811 * If this flag is set, the driver should instruct the hardware to
812 * assign a sequence number to the frame or assign one itself. Cf. IEEE
813 * 802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
814 * beacons and always be clear for frames without a sequence number field.
815 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
816 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
817 * station
818 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
819 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
820 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
821 * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
822 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
823 * because the destination STA was in powersave mode. Note that to
824 * avoid race conditions, the filter must be set by the hardware or
825 * firmware upon receiving a frame that indicates that the station
826 * went to sleep (must be done on device to filter frames already on
827 * the queue) and may only be unset after mac80211 gives the OK for
828 * that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above),
829 * since only then is it guaranteed that no more frames are in the
830 * hardware queue.
831 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
832 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
833 * is for the whole aggregation.
834 * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
835 * so consider using block ack request (BAR).
836 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
837 * set by rate control algorithms to indicate probe rate, will
838 * be cleared for fragmented frames (except on the last fragment)
839 * @IEEE80211_TX_INTFL_OFFCHAN_TX_OK: Internal to mac80211. Used to indicate
840 * that a frame can be transmitted while the queues are stopped for
841 * off-channel operation.
842 * @IEEE80211_TX_CTL_HW_80211_ENCAP: This frame uses hardware encapsulation
843 * (header conversion)
844 * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211,
845 * used to indicate that a frame was already retried due to PS
846 * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
847 * used to indicate frame should not be encrypted
848 * @IEEE80211_TX_CTL_NO_PS_BUFFER: This frame is a response to a poll
849 * frame (PS-Poll or uAPSD) or a non-bufferable MMPDU and must
850 * be sent although the station is in powersave mode.
851 * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the
852 * transmit function after the current frame, this can be used
853 * by drivers to kick the DMA queue only if unset or when the
854 * queue gets full.
855 * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted
856 * after TX status because the destination was asleep, it must not
857 * be modified again (no seqno assignment, crypto, etc.)
858 * @IEEE80211_TX_INTFL_MLME_CONN_TX: This frame was transmitted by the MLME
859 * code for connection establishment, this indicates that its status
860 * should kick the MLME state machine.
861 * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211
862 * MLME command (internal to mac80211 to figure out whether to send TX
863 * status to user space)
864 * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame
865 * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this
866 * frame and selects the maximum number of streams that it can use.
867 * @IEEE80211_TX_CTL_TX_OFFCHAN: Marks this packet to be transmitted on
868 * the off-channel channel when a remain-on-channel offload is done
869 * in hardware -- normal packets still flow and are expected to be
870 * handled properly by the device.
871 * @IEEE80211_TX_INTFL_TKIP_MIC_FAILURE: Marks this packet to be used for TKIP
872 * testing. It will be sent out with incorrect Michael MIC key to allow
873 * TKIP countermeasures to be tested.
874 * @IEEE80211_TX_CTL_NO_CCK_RATE: This frame will be sent at non CCK rate.
875 * This flag is actually used for management frame especially for P2P
876 * frames not being sent at CCK rate in 2GHz band.
877 * @IEEE80211_TX_STATUS_EOSP: This packet marks the end of service period,
878 * when its status is reported the service period ends. For frames in
879 * an SP that mac80211 transmits, it is already set; for driver frames
880 * the driver may set this flag. It is also used to do the same for
881 * PS-Poll responses.
882 * @IEEE80211_TX_CTL_USE_MINRATE: This frame will be sent at lowest rate.
883 * This flag is used to send nullfunc frame at minimum rate when
884 * the nullfunc is used for connection monitoring purpose.
885 * @IEEE80211_TX_CTL_DONTFRAG: Don't fragment this packet even if it
886 * would be fragmented by size (this is optional, only used for
887 * monitor injection).
888 * @IEEE80211_TX_STAT_NOACK_TRANSMITTED: A frame that was marked with
889 * IEEE80211_TX_CTL_NO_ACK has been successfully transmitted without
890 * any errors (like issues specific to the driver/HW).
891 * This flag must not be set for frames that don't request no-ack
892 * behaviour with IEEE80211_TX_CTL_NO_ACK.
893 *
894 * Note: If you have to add new flags to the enumeration, then don't
895 * forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary.
896 */
897enum mac80211_tx_info_flags {
898 IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
899 IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(1),
900 IEEE80211_TX_CTL_NO_ACK = BIT(2),
901 IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(3),
902 IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(4),
903 IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(5),
904 IEEE80211_TX_CTL_AMPDU = BIT(6),
905 IEEE80211_TX_CTL_INJECTED = BIT(7),
906 IEEE80211_TX_STAT_TX_FILTERED = BIT(8),
907 IEEE80211_TX_STAT_ACK = BIT(9),
908 IEEE80211_TX_STAT_AMPDU = BIT(10),
909 IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11),
910 IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12),
911 IEEE80211_TX_INTFL_OFFCHAN_TX_OK = BIT(13),
912 IEEE80211_TX_CTL_HW_80211_ENCAP = BIT(14),
913 IEEE80211_TX_INTFL_RETRIED = BIT(15),
914 IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16),
915 IEEE80211_TX_CTL_NO_PS_BUFFER = BIT(17),
916 IEEE80211_TX_CTL_MORE_FRAMES = BIT(18),
917 IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19),
918 IEEE80211_TX_INTFL_MLME_CONN_TX = BIT(20),
919 IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21),
920 IEEE80211_TX_CTL_LDPC = BIT(22),
921 IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24),
922 IEEE80211_TX_CTL_TX_OFFCHAN = BIT(25),
923 IEEE80211_TX_INTFL_TKIP_MIC_FAILURE = BIT(26),
924 IEEE80211_TX_CTL_NO_CCK_RATE = BIT(27),
925 IEEE80211_TX_STATUS_EOSP = BIT(28),
926 IEEE80211_TX_CTL_USE_MINRATE = BIT(29),
927 IEEE80211_TX_CTL_DONTFRAG = BIT(30),
928 IEEE80211_TX_STAT_NOACK_TRANSMITTED = BIT(31),
929};
930
931#define IEEE80211_TX_CTL_STBC_SHIFT 23
932
933#define IEEE80211_TX_RC_S1G_MCS IEEE80211_TX_RC_VHT_MCS
934
935/**
936 * enum mac80211_tx_control_flags - flags to describe transmit control
937 *
938 * @IEEE80211_TX_CTRL_PORT_CTRL_PROTO: this frame is a port control
939 * protocol frame (e.g. EAP)
940 * @IEEE80211_TX_CTRL_PS_RESPONSE: This frame is a response to a poll
941 * frame (PS-Poll or uAPSD).
942 * @IEEE80211_TX_CTRL_RATE_INJECT: This frame is injected with rate information
943 * @IEEE80211_TX_CTRL_AMSDU: This frame is an A-MSDU frame
944 * @IEEE80211_TX_CTRL_FAST_XMIT: This frame is going through the fast_xmit path
945 * @IEEE80211_TX_CTRL_SKIP_MPATH_LOOKUP: This frame skips mesh path lookup
946 * @IEEE80211_TX_INTCFL_NEED_TXPROCESSING: completely internal to mac80211,
947 * used to indicate that a pending frame requires TX processing before
948 * it can be sent out.
949 * @IEEE80211_TX_CTRL_NO_SEQNO: Do not overwrite the sequence number that
950 * has already been assigned to this frame.
951 * @IEEE80211_TX_CTRL_DONT_REORDER: This frame should not be reordered
952 * relative to other frames that have this flag set, independent
953 * of their QoS TID or other priority field values.
954 * @IEEE80211_TX_CTRL_MCAST_MLO_FIRST_TX: first MLO TX, used mostly internally
955 * for sequence number assignment
956 * @IEEE80211_TX_CTRL_SCAN_TX: Indicates that this frame is transmitted
957 * due to scanning, not in normal operation on the interface.
958 * @IEEE80211_TX_CTRL_MLO_LINK: If not @IEEE80211_LINK_UNSPECIFIED, this
959 * frame should be transmitted on the specific link. This really is
960 * only relevant for frames that do not have data present, and is
961 * also not used for 802.3 format frames. Note that even if the frame
962 * is on a specific link, address translation might still apply if
963 * it's intended for an MLD.
964 *
965 * These flags are used in tx_info->control.flags.
966 */
967enum mac80211_tx_control_flags {
968 IEEE80211_TX_CTRL_PORT_CTRL_PROTO = BIT(0),
969 IEEE80211_TX_CTRL_PS_RESPONSE = BIT(1),
970 IEEE80211_TX_CTRL_RATE_INJECT = BIT(2),
971 IEEE80211_TX_CTRL_AMSDU = BIT(3),
972 IEEE80211_TX_CTRL_FAST_XMIT = BIT(4),
973 IEEE80211_TX_CTRL_SKIP_MPATH_LOOKUP = BIT(5),
974 IEEE80211_TX_INTCFL_NEED_TXPROCESSING = BIT(6),
975 IEEE80211_TX_CTRL_NO_SEQNO = BIT(7),
976 IEEE80211_TX_CTRL_DONT_REORDER = BIT(8),
977 IEEE80211_TX_CTRL_MCAST_MLO_FIRST_TX = BIT(9),
978 IEEE80211_TX_CTRL_SCAN_TX = BIT(10),
979 IEEE80211_TX_CTRL_MLO_LINK = 0xf0000000,
980};
981
982#define IEEE80211_LINK_UNSPECIFIED 0xf
983#define IEEE80211_TX_CTRL_MLO_LINK_UNSPEC \
984 u32_encode_bits(IEEE80211_LINK_UNSPECIFIED, \
985 IEEE80211_TX_CTRL_MLO_LINK)
986
987/**
988 * enum mac80211_tx_status_flags - flags to describe transmit status
989 *
990 * @IEEE80211_TX_STATUS_ACK_SIGNAL_VALID: ACK signal is valid
991 *
992 * These flags are used in tx_info->status.flags.
993 */
994enum mac80211_tx_status_flags {
995 IEEE80211_TX_STATUS_ACK_SIGNAL_VALID = BIT(0),
996};
997
998/*
999 * This definition is used as a mask to clear all temporary flags, which are
1000 * set by the tx handlers for each transmission attempt by the mac80211 stack.
1001 */
1002#define IEEE80211_TX_TEMPORARY_FLAGS (IEEE80211_TX_CTL_NO_ACK | \
1003 IEEE80211_TX_CTL_CLEAR_PS_FILT | IEEE80211_TX_CTL_FIRST_FRAGMENT | \
1004 IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU | \
1005 IEEE80211_TX_STAT_TX_FILTERED | IEEE80211_TX_STAT_ACK | \
1006 IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK | \
1007 IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_NO_PS_BUFFER | \
1008 IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC | \
1009 IEEE80211_TX_CTL_STBC | IEEE80211_TX_STATUS_EOSP)
1010
1011/**
1012 * enum mac80211_rate_control_flags - per-rate flags set by the
1013 * Rate Control algorithm.
1014 *
1015 * These flags are set by the Rate control algorithm for each rate during tx,
1016 * in the @flags member of struct ieee80211_tx_rate.
1017 *
1018 * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
1019 * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
1020 * This is set if the current BSS requires ERP protection.
1021 * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
1022 * @IEEE80211_TX_RC_MCS: HT rate.
1023 * @IEEE80211_TX_RC_VHT_MCS: VHT MCS rate, in this case the idx field is split
1024 * into a higher 4 bits (Nss) and lower 4 bits (MCS number)
1025 * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
1026 * Greenfield mode.
1027 * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
1028 * @IEEE80211_TX_RC_80_MHZ_WIDTH: Indicates 80 MHz transmission
1029 * @IEEE80211_TX_RC_160_MHZ_WIDTH: Indicates 160 MHz transmission
1030 * (80+80 isn't supported yet)
1031 * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
1032 * adjacent 20 MHz channels, if the current channel type is
1033 * NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
1034 * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
1035 */
1036enum mac80211_rate_control_flags {
1037 IEEE80211_TX_RC_USE_RTS_CTS = BIT(0),
1038 IEEE80211_TX_RC_USE_CTS_PROTECT = BIT(1),
1039 IEEE80211_TX_RC_USE_SHORT_PREAMBLE = BIT(2),
1040
1041 /* rate index is an HT/VHT MCS instead of an index */
1042 IEEE80211_TX_RC_MCS = BIT(3),
1043 IEEE80211_TX_RC_GREEN_FIELD = BIT(4),
1044 IEEE80211_TX_RC_40_MHZ_WIDTH = BIT(5),
1045 IEEE80211_TX_RC_DUP_DATA = BIT(6),
1046 IEEE80211_TX_RC_SHORT_GI = BIT(7),
1047 IEEE80211_TX_RC_VHT_MCS = BIT(8),
1048 IEEE80211_TX_RC_80_MHZ_WIDTH = BIT(9),
1049 IEEE80211_TX_RC_160_MHZ_WIDTH = BIT(10),
1050};
1051
1052
1053/* there are 40 bytes if you don't need the rateset to be kept */
1054#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
1055
1056/* if you do need the rateset, then you have less space */
1057#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
1058
1059/* maximum number of rate stages */
1060#define IEEE80211_TX_MAX_RATES 4
1061
1062/* maximum number of rate table entries */
1063#define IEEE80211_TX_RATE_TABLE_SIZE 4
1064
1065/**
1066 * struct ieee80211_tx_rate - rate selection/status
1067 *
1068 * @idx: rate index to attempt to send with
1069 * @flags: rate control flags (&enum mac80211_rate_control_flags)
1070 * @count: number of tries in this rate before going to the next rate
1071 *
1072 * A value of -1 for @idx indicates an invalid rate and, if used
1073 * in an array of retry rates, that no more rates should be tried.
1074 *
1075 * When used for transmit status reporting, the driver should
1076 * always report the rate along with the flags it used.
1077 *
1078 * &struct ieee80211_tx_info contains an array of these structs
1079 * in the control information, and it will be filled by the rate
1080 * control algorithm according to what should be sent. For example,
1081 * if this array contains, in the format { <idx>, <count> } the
1082 * information::
1083 *
1084 * { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 }
1085 *
1086 * then this means that the frame should be transmitted
1087 * up to twice at rate 3, up to twice at rate 2, and up to four
1088 * times at rate 1 if it doesn't get acknowledged. Say it gets
1089 * acknowledged by the peer after the fifth attempt, the status
1090 * information should then contain::
1091 *
1092 * { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ...
1093 *
1094 * since it was transmitted twice at rate 3, twice at rate 2
1095 * and once at rate 1 after which we received an acknowledgement.
1096 */
1097struct ieee80211_tx_rate {
1098 s8 idx;
1099 u16 count:5,
1100 flags:11;
1101} __packed;
1102
1103#define IEEE80211_MAX_TX_RETRY 31
1104
1105static inline bool ieee80211_rate_valid(struct ieee80211_tx_rate *rate)
1106{
1107 return rate->idx >= 0 && rate->count > 0;
1108}
1109
1110static inline void ieee80211_rate_set_vht(struct ieee80211_tx_rate *rate,
1111 u8 mcs, u8 nss)
1112{
1113 WARN_ON(mcs & ~0xF);
1114 WARN_ON((nss - 1) & ~0x7);
1115 rate->idx = ((nss - 1) << 4) | mcs;
1116}
1117
1118static inline u8
1119ieee80211_rate_get_vht_mcs(const struct ieee80211_tx_rate *rate)
1120{
1121 return rate->idx & 0xF;
1122}
1123
1124static inline u8
1125ieee80211_rate_get_vht_nss(const struct ieee80211_tx_rate *rate)
1126{
1127 return (rate->idx >> 4) + 1;
1128}
1129
1130/**
1131 * struct ieee80211_tx_info - skb transmit information
1132 *
1133 * This structure is placed in skb->cb for three uses:
1134 * (1) mac80211 TX control - mac80211 tells the driver what to do
1135 * (2) driver internal use (if applicable)
1136 * (3) TX status information - driver tells mac80211 what happened
1137 *
1138 * @flags: transmit info flags, defined above
1139 * @band: the band to transmit on (use e.g. for checking for races),
1140 * not valid if the interface is an MLD since we won't know which
1141 * link the frame will be transmitted on
1142 * @hw_queue: HW queue to put the frame on, skb_get_queue_mapping() gives the AC
1143 * @status_data: internal data for TX status handling, assigned privately,
1144 * see also &enum ieee80211_status_data for the internal documentation
1145 * @status_data_idr: indicates status data is IDR allocated ID for ack frame
1146 * @tx_time_est: TX time estimate in units of 4us, used internally
1147 * @control: union part for control data
1148 * @control.rates: TX rates array to try
1149 * @control.rts_cts_rate_idx: rate for RTS or CTS
1150 * @control.use_rts: use RTS
1151 * @control.use_cts_prot: use RTS/CTS
1152 * @control.short_preamble: use short preamble (CCK only)
1153 * @control.skip_table: skip externally configured rate table
1154 * @control.jiffies: timestamp for expiry on powersave clients
1155 * @control.vif: virtual interface (may be NULL)
1156 * @control.hw_key: key to encrypt with (may be NULL)
1157 * @control.flags: control flags, see &enum mac80211_tx_control_flags
1158 * @control.enqueue_time: enqueue time (for iTXQs)
1159 * @driver_rates: alias to @control.rates to reserve space
1160 * @pad: padding
1161 * @rate_driver_data: driver use area if driver needs @control.rates
1162 * @status: union part for status data
1163 * @status.rates: attempted rates
1164 * @status.ack_signal: ACK signal
1165 * @status.ampdu_ack_len: AMPDU ack length
1166 * @status.ampdu_len: AMPDU length
1167 * @status.antenna: (legacy, kept only for iwlegacy)
1168 * @status.tx_time: airtime consumed for transmission; note this is only
1169 * used for WMM AC, not for airtime fairness
1170 * @status.flags: status flags, see &enum mac80211_tx_status_flags
1171 * @status.status_driver_data: driver use area
1172 * @ack: union part for pure ACK data
1173 * @ack.cookie: cookie for the ACK
1174 * @driver_data: array of driver_data pointers
1175 */
1176struct ieee80211_tx_info {
1177 /* common information */
1178 u32 flags;
1179 u32 band:3,
1180 status_data_idr:1,
1181 status_data:13,
1182 hw_queue:4,
1183 tx_time_est:10;
1184 /* 1 free bit */
1185
1186 union {
1187 struct {
1188 union {
1189 /* rate control */
1190 struct {
1191 struct ieee80211_tx_rate rates[
1192 IEEE80211_TX_MAX_RATES];
1193 s8 rts_cts_rate_idx;
1194 u8 use_rts:1;
1195 u8 use_cts_prot:1;
1196 u8 short_preamble:1;
1197 u8 skip_table:1;
1198
1199 /* for injection only (bitmap) */
1200 u8 antennas:2;
1201
1202 /* 14 bits free */
1203 };
1204 /* only needed before rate control */
1205 unsigned long jiffies;
1206 };
1207 /* NB: vif can be NULL for injected frames */
1208 struct ieee80211_vif *vif;
1209 struct ieee80211_key_conf *hw_key;
1210 u32 flags;
1211 codel_time_t enqueue_time;
1212 } control;
1213 struct {
1214 u64 cookie;
1215 } ack;
1216 struct {
1217 struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
1218 s32 ack_signal;
1219 u8 ampdu_ack_len;
1220 u8 ampdu_len;
1221 u8 antenna;
1222 u8 pad;
1223 u16 tx_time;
1224 u8 flags;
1225 u8 pad2;
1226 void *status_driver_data[16 / sizeof(void *)];
1227 } status;
1228 struct {
1229 struct ieee80211_tx_rate driver_rates[
1230 IEEE80211_TX_MAX_RATES];
1231 u8 pad[4];
1232
1233 void *rate_driver_data[
1234 IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
1235 };
1236 void *driver_data[
1237 IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
1238 };
1239};
1240
1241static inline u16
1242ieee80211_info_set_tx_time_est(struct ieee80211_tx_info *info, u16 tx_time_est)
1243{
1244 /* We only have 10 bits in tx_time_est, so store airtime
1245 * in increments of 4us and clamp the maximum to 2**12-1
1246 */
1247 info->tx_time_est = min_t(u16, tx_time_est, 4095) >> 2;
1248 return info->tx_time_est << 2;
1249}
1250
1251static inline u16
1252ieee80211_info_get_tx_time_est(struct ieee80211_tx_info *info)
1253{
1254 return info->tx_time_est << 2;
1255}
1256
1257/***
1258 * struct ieee80211_rate_status - mrr stage for status path
1259 *
1260 * This struct is used in struct ieee80211_tx_status to provide drivers a
1261 * dynamic way to report about used rates and power levels per packet.
1262 *
1263 * @rate_idx The actual used rate.
1264 * @try_count How often the rate was tried.
1265 * @tx_power_idx An idx into the ieee80211_hw->tx_power_levels list of the
1266 * corresponding wifi hardware. The idx shall point to the power level
1267 * that was used when sending the packet.
1268 */
1269struct ieee80211_rate_status {
1270 struct rate_info rate_idx;
1271 u8 try_count;
1272 u8 tx_power_idx;
1273};
1274
1275/**
1276 * struct ieee80211_tx_status - extended tx status info for rate control
1277 *
1278 * @sta: Station that the packet was transmitted for
1279 * @info: Basic tx status information
1280 * @skb: Packet skb (can be NULL if not provided by the driver)
1281 * @rates: Mrr stages that were used when sending the packet
1282 * @n_rates: Number of mrr stages (count of instances for @rates)
1283 * @free_list: list where processed skbs are stored to be free'd by the driver
1284 * @ack_hwtstamp: Hardware timestamp of the received ack in nanoseconds
1285 * Only needed for Timing measurement and Fine timing measurement action
1286 * frames. Only reported by devices that have timestamping enabled.
1287 */
1288struct ieee80211_tx_status {
1289 struct ieee80211_sta *sta;
1290 struct ieee80211_tx_info *info;
1291 struct sk_buff *skb;
1292 struct ieee80211_rate_status *rates;
1293 ktime_t ack_hwtstamp;
1294 u8 n_rates;
1295
1296 struct list_head *free_list;
1297};
1298
1299/**
1300 * struct ieee80211_scan_ies - descriptors for different blocks of IEs
1301 *
1302 * This structure is used to point to different blocks of IEs in HW scan
1303 * and scheduled scan. These blocks contain the IEs passed by userspace
1304 * and the ones generated by mac80211.
1305 *
1306 * @ies: pointers to band specific IEs.
1307 * @len: lengths of band_specific IEs.
1308 * @common_ies: IEs for all bands (especially vendor specific ones)
1309 * @common_ie_len: length of the common_ies
1310 */
1311struct ieee80211_scan_ies {
1312 const u8 *ies[NUM_NL80211_BANDS];
1313 size_t len[NUM_NL80211_BANDS];
1314 const u8 *common_ies;
1315 size_t common_ie_len;
1316};
1317
1318
1319static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
1320{
1321 return (struct ieee80211_tx_info *)skb->cb;
1322}
1323
1324static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb)
1325{
1326 return (struct ieee80211_rx_status *)skb->cb;
1327}
1328
1329/**
1330 * ieee80211_tx_info_clear_status - clear TX status
1331 *
1332 * @info: The &struct ieee80211_tx_info to be cleared.
1333 *
1334 * When the driver passes an skb back to mac80211, it must report
1335 * a number of things in TX status. This function clears everything
1336 * in the TX status but the rate control information (it does clear
1337 * the count since you need to fill that in anyway).
1338 *
1339 * NOTE: While the rates array is kept intact, this will wipe all of the
1340 * driver_data fields in info, so it's up to the driver to restore
1341 * any fields it needs after calling this helper.
1342 */
1343static inline void
1344ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
1345{
1346 int i;
1347
1348 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
1349 offsetof(struct ieee80211_tx_info, control.rates));
1350 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
1351 offsetof(struct ieee80211_tx_info, driver_rates));
1352 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
1353 /* clear the rate counts */
1354 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
1355 info->status.rates[i].count = 0;
1356 memset_after(&info->status, 0, rates);
1357}
1358
1359
1360/**
1361 * enum mac80211_rx_flags - receive flags
1362 *
1363 * These flags are used with the @flag member of &struct ieee80211_rx_status.
1364 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
1365 * Use together with %RX_FLAG_MMIC_STRIPPED.
1366 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
1367 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
1368 * verification has been done by the hardware.
1369 * @RX_FLAG_IV_STRIPPED: The IV and ICV are stripped from this frame.
1370 * If this flag is set, the stack cannot do any replay detection
1371 * hence the driver or hardware will have to do that.
1372 * @RX_FLAG_PN_VALIDATED: Currently only valid for CCMP/GCMP frames, this
1373 * flag indicates that the PN was verified for replay protection.
1374 * Note that this flag is also currently only supported when a frame
1375 * is also decrypted (ie. @RX_FLAG_DECRYPTED must be set)
1376 * @RX_FLAG_DUP_VALIDATED: The driver should set this flag if it did
1377 * de-duplication by itself.
1378 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
1379 * the frame.
1380 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
1381 * the frame.
1382 * @RX_FLAG_MACTIME: The timestamp passed in the RX status (@mactime
1383 * field) is valid if this field is non-zero, and the position
1384 * where the timestamp was sampled depends on the value.
1385 * @RX_FLAG_MACTIME_START: The timestamp passed in the RX status (@mactime
1386 * field) is valid and contains the time the first symbol of the MPDU
1387 * was received. This is useful in monitor mode and for proper IBSS
1388 * merging.
1389 * @RX_FLAG_MACTIME_END: The timestamp passed in the RX status (@mactime
1390 * field) is valid and contains the time the last symbol of the MPDU
1391 * (including FCS) was received.
1392 * @RX_FLAG_MACTIME_PLCP_START: The timestamp passed in the RX status (@mactime
1393 * field) is valid and contains the time the SYNC preamble was received.
1394 * @RX_FLAG_MACTIME_IS_RTAP_TS64: The timestamp passed in the RX status @mactime
1395 * is only for use in the radiotap timestamp header, not otherwise a valid
1396 * @mactime value. Note this is a separate flag so that we continue to see
1397 * %RX_FLAG_MACTIME as unset. Also note that in this case the timestamp is
1398 * reported to be 64 bits wide, not just 32.
1399 * @RX_FLAG_NO_SIGNAL_VAL: The signal strength value is not present.
1400 * Valid only for data frames (mainly A-MPDU)
1401 * @RX_FLAG_AMPDU_DETAILS: A-MPDU details are known, in particular the reference
1402 * number (@ampdu_reference) must be populated and be a distinct number for
1403 * each A-MPDU
1404 * @RX_FLAG_AMPDU_LAST_KNOWN: last subframe is known, should be set on all
1405 * subframes of a single A-MPDU
1406 * @RX_FLAG_AMPDU_IS_LAST: this subframe is the last subframe of the A-MPDU
1407 * @RX_FLAG_AMPDU_DELIM_CRC_ERROR: A delimiter CRC error has been detected
1408 * on this subframe
1409 * @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC
1410 * is stored in the @ampdu_delimiter_crc field)
1411 * @RX_FLAG_MIC_STRIPPED: The mic was stripped of this packet. Decryption was
1412 * done by the hardware
1413 * @RX_FLAG_ONLY_MONITOR: Report frame only to monitor interfaces without
1414 * processing it in any regular way.
1415 * This is useful if drivers offload some frames but still want to report
1416 * them for sniffing purposes.
1417 * @RX_FLAG_SKIP_MONITOR: Process and report frame to all interfaces except
1418 * monitor interfaces.
1419 * This is useful if drivers offload some frames but still want to report
1420 * them for sniffing purposes.
1421 * @RX_FLAG_AMSDU_MORE: Some drivers may prefer to report separate A-MSDU
1422 * subframes instead of a one huge frame for performance reasons.
1423 * All, but the last MSDU from an A-MSDU should have this flag set. E.g.
1424 * if an A-MSDU has 3 frames, the first 2 must have the flag set, while
1425 * the 3rd (last) one must not have this flag set. The flag is used to
1426 * deal with retransmission/duplication recovery properly since A-MSDU
1427 * subframes share the same sequence number. Reported subframes can be
1428 * either regular MSDU or singly A-MSDUs. Subframes must not be
1429 * interleaved with other frames.
1430 * @RX_FLAG_RADIOTAP_TLV_AT_END: This frame contains radiotap TLVs in the
1431 * skb->data (before the 802.11 header).
1432 * If used, the SKB's mac_header pointer must be set to point
1433 * to the 802.11 header after the TLVs, and any padding added after TLV
1434 * data to align to 4 must be cleared by the driver putting the TLVs
1435 * in the skb.
1436 * @RX_FLAG_ALLOW_SAME_PN: Allow the same PN as same packet before.
1437 * This is used for AMSDU subframes which can have the same PN as
1438 * the first subframe.
1439 * @RX_FLAG_ICV_STRIPPED: The ICV is stripped from this frame. CRC checking must
1440 * be done in the hardware.
1441 * @RX_FLAG_AMPDU_EOF_BIT: Value of the EOF bit in the A-MPDU delimiter for this
1442 * frame
1443 * @RX_FLAG_AMPDU_EOF_BIT_KNOWN: The EOF value is known
1444 * @RX_FLAG_RADIOTAP_HE: HE radiotap data is present
1445 * (&struct ieee80211_radiotap_he, mac80211 will fill in
1446 *
1447 * - DATA3_DATA_MCS
1448 * - DATA3_DATA_DCM
1449 * - DATA3_CODING
1450 * - DATA5_GI
1451 * - DATA5_DATA_BW_RU_ALLOC
1452 * - DATA6_NSTS
1453 * - DATA3_STBC
1454 *
1455 * from the RX info data, so leave those zeroed when building this data)
1456 * @RX_FLAG_RADIOTAP_HE_MU: HE MU radiotap data is present
1457 * (&struct ieee80211_radiotap_he_mu)
1458 * @RX_FLAG_RADIOTAP_LSIG: L-SIG radiotap data is present
1459 * @RX_FLAG_NO_PSDU: use the frame only for radiotap reporting, with
1460 * the "0-length PSDU" field included there. The value for it is
1461 * in &struct ieee80211_rx_status. Note that if this value isn't
1462 * known the frame shouldn't be reported.
1463 * @RX_FLAG_8023: the frame has an 802.3 header (decap offload performed by
1464 * hardware or driver)
1465 */
1466enum mac80211_rx_flags {
1467 RX_FLAG_MMIC_ERROR = BIT(0),
1468 RX_FLAG_DECRYPTED = BIT(1),
1469 RX_FLAG_ONLY_MONITOR = BIT(2),
1470 RX_FLAG_MMIC_STRIPPED = BIT(3),
1471 RX_FLAG_IV_STRIPPED = BIT(4),
1472 RX_FLAG_FAILED_FCS_CRC = BIT(5),
1473 RX_FLAG_FAILED_PLCP_CRC = BIT(6),
1474 RX_FLAG_MACTIME_IS_RTAP_TS64 = BIT(7),
1475 RX_FLAG_NO_SIGNAL_VAL = BIT(8),
1476 RX_FLAG_AMPDU_DETAILS = BIT(9),
1477 RX_FLAG_PN_VALIDATED = BIT(10),
1478 RX_FLAG_DUP_VALIDATED = BIT(11),
1479 RX_FLAG_AMPDU_LAST_KNOWN = BIT(12),
1480 RX_FLAG_AMPDU_IS_LAST = BIT(13),
1481 RX_FLAG_AMPDU_DELIM_CRC_ERROR = BIT(14),
1482 RX_FLAG_AMPDU_DELIM_CRC_KNOWN = BIT(15),
1483 RX_FLAG_MACTIME = BIT(16) | BIT(17),
1484 RX_FLAG_MACTIME_PLCP_START = 1 << 16,
1485 RX_FLAG_MACTIME_START = 2 << 16,
1486 RX_FLAG_MACTIME_END = 3 << 16,
1487 RX_FLAG_SKIP_MONITOR = BIT(18),
1488 RX_FLAG_AMSDU_MORE = BIT(19),
1489 RX_FLAG_RADIOTAP_TLV_AT_END = BIT(20),
1490 RX_FLAG_MIC_STRIPPED = BIT(21),
1491 RX_FLAG_ALLOW_SAME_PN = BIT(22),
1492 RX_FLAG_ICV_STRIPPED = BIT(23),
1493 RX_FLAG_AMPDU_EOF_BIT = BIT(24),
1494 RX_FLAG_AMPDU_EOF_BIT_KNOWN = BIT(25),
1495 RX_FLAG_RADIOTAP_HE = BIT(26),
1496 RX_FLAG_RADIOTAP_HE_MU = BIT(27),
1497 RX_FLAG_RADIOTAP_LSIG = BIT(28),
1498 RX_FLAG_NO_PSDU = BIT(29),
1499 RX_FLAG_8023 = BIT(30),
1500};
1501
1502/**
1503 * enum mac80211_rx_encoding_flags - MCS & bandwidth flags
1504 *
1505 * @RX_ENC_FLAG_SHORTPRE: Short preamble was used for this frame
1506 * @RX_ENC_FLAG_SHORT_GI: Short guard interval was used
1507 * @RX_ENC_FLAG_HT_GF: This frame was received in a HT-greenfield transmission,
1508 * if the driver fills this value it should add
1509 * %IEEE80211_RADIOTAP_MCS_HAVE_FMT
1510 * to @hw.radiotap_mcs_details to advertise that fact.
1511 * @RX_ENC_FLAG_LDPC: LDPC was used
1512 * @RX_ENC_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
1513 * @RX_ENC_FLAG_BF: packet was beamformed
1514 */
1515enum mac80211_rx_encoding_flags {
1516 RX_ENC_FLAG_SHORTPRE = BIT(0),
1517 RX_ENC_FLAG_SHORT_GI = BIT(2),
1518 RX_ENC_FLAG_HT_GF = BIT(3),
1519 RX_ENC_FLAG_STBC_MASK = BIT(4) | BIT(5),
1520 RX_ENC_FLAG_LDPC = BIT(6),
1521 RX_ENC_FLAG_BF = BIT(7),
1522};
1523
1524#define RX_ENC_FLAG_STBC_SHIFT 4
1525
1526enum mac80211_rx_encoding {
1527 RX_ENC_LEGACY = 0,
1528 RX_ENC_HT,
1529 RX_ENC_VHT,
1530 RX_ENC_HE,
1531 RX_ENC_EHT,
1532};
1533
1534/**
1535 * struct ieee80211_rx_status - receive status
1536 *
1537 * The low-level driver should provide this information (the subset
1538 * supported by hardware) to the 802.11 code with each received
1539 * frame, in the skb's control buffer (cb).
1540 *
1541 * @mactime: value in microseconds of the 64-bit Time Synchronization Function
1542 * (TSF) timer when the first data symbol (MPDU) arrived at the hardware.
1543 * @boottime_ns: CLOCK_BOOTTIME timestamp the frame was received at, this is
1544 * needed only for beacons and probe responses that update the scan cache.
1545 * @ack_tx_hwtstamp: Hardware timestamp for the ack TX in nanoseconds. Only
1546 * needed for Timing measurement and Fine timing measurement action frames.
1547 * Only reported by devices that have timestamping enabled.
1548 * @device_timestamp: arbitrary timestamp for the device, mac80211 doesn't use
1549 * it but can store it and pass it back to the driver for synchronisation
1550 * @band: the active band when this frame was received
1551 * @freq: frequency the radio was tuned to when receiving this frame, in MHz
1552 * This field must be set for management frames, but isn't strictly needed
1553 * for data (other) frames - for those it only affects radiotap reporting.
1554 * @freq_offset: @freq has a positive offset of 500Khz.
1555 * @signal: signal strength when receiving this frame, either in dBm, in dB or
1556 * unspecified depending on the hardware capabilities flags
1557 * @IEEE80211_HW_SIGNAL_*
1558 * @chains: bitmask of receive chains for which separate signal strength
1559 * values were filled.
1560 * @chain_signal: per-chain signal strength, in dBm (unlike @signal, doesn't
1561 * support dB or unspecified units)
1562 * @antenna: antenna used
1563 * @rate_idx: index of data rate into band's supported rates or MCS index if
1564 * HT or VHT is used (%RX_FLAG_HT/%RX_FLAG_VHT)
1565 * @nss: number of streams (VHT, HE and EHT only)
1566 * @flag: %RX_FLAG_\*
1567 * @encoding: &enum mac80211_rx_encoding
1568 * @bw: &enum rate_info_bw
1569 * @enc_flags: uses bits from &enum mac80211_rx_encoding_flags
1570 * @he_ru: HE RU, from &enum nl80211_he_ru_alloc
1571 * @he_gi: HE GI, from &enum nl80211_he_gi
1572 * @he_dcm: HE DCM value
1573 * @eht: EHT specific rate information
1574 * @eht.ru: EHT RU, from &enum nl80211_eht_ru_alloc
1575 * @eht.gi: EHT GI, from &enum nl80211_eht_gi
1576 * @rx_flags: internal RX flags for mac80211
1577 * @ampdu_reference: A-MPDU reference number, must be a different value for
1578 * each A-MPDU but the same for each subframe within one A-MPDU
1579 * @ampdu_delimiter_crc: A-MPDU delimiter CRC
1580 * @zero_length_psdu_type: radiotap type of the 0-length PSDU
1581 * @link_valid: if the link which is identified by @link_id is valid. This flag
1582 * is set only when connection is MLO.
1583 * @link_id: id of the link used to receive the packet. This is used along with
1584 * @link_valid.
1585 */
1586struct ieee80211_rx_status {
1587 u64 mactime;
1588 union {
1589 u64 boottime_ns;
1590 ktime_t ack_tx_hwtstamp;
1591 };
1592 u32 device_timestamp;
1593 u32 ampdu_reference;
1594 u32 flag;
1595 u16 freq: 13, freq_offset: 1;
1596 u8 enc_flags;
1597 u8 encoding:3, bw:4;
1598 union {
1599 struct {
1600 u8 he_ru:3;
1601 u8 he_gi:2;
1602 u8 he_dcm:1;
1603 };
1604 struct {
1605 u8 ru:4;
1606 u8 gi:2;
1607 } eht;
1608 };
1609 u8 rate_idx;
1610 u8 nss;
1611 u8 rx_flags;
1612 u8 band;
1613 u8 antenna;
1614 s8 signal;
1615 u8 chains;
1616 s8 chain_signal[IEEE80211_MAX_CHAINS];
1617 u8 ampdu_delimiter_crc;
1618 u8 zero_length_psdu_type;
1619 u8 link_valid:1, link_id:4;
1620};
1621
1622static inline u32
1623ieee80211_rx_status_to_khz(struct ieee80211_rx_status *rx_status)
1624{
1625 return MHZ_TO_KHZ(rx_status->freq) +
1626 (rx_status->freq_offset ? 500 : 0);
1627}
1628
1629/**
1630 * enum ieee80211_conf_flags - configuration flags
1631 *
1632 * Flags to define PHY configuration options
1633 *
1634 * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
1635 * to determine for example whether to calculate timestamps for packets
1636 * or not, do not use instead of filter flags!
1637 * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only).
1638 * This is the power save mode defined by IEEE 802.11-2007 section 11.2,
1639 * meaning that the hardware still wakes up for beacons, is able to
1640 * transmit frames and receive the possible acknowledgment frames.
1641 * Not to be confused with hardware specific wakeup/sleep states,
1642 * driver is responsible for that. See the section "Powersave support"
1643 * for more.
1644 * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
1645 * the driver should be prepared to handle configuration requests but
1646 * may turn the device off as much as possible. Typically, this flag will
1647 * be set when an interface is set UP but not associated or scanning, but
1648 * it can also be unset in that case when monitor interfaces are active.
1649 * @IEEE80211_CONF_OFFCHANNEL: The device is currently not on its main
1650 * operating channel.
1651 */
1652enum ieee80211_conf_flags {
1653 IEEE80211_CONF_MONITOR = (1<<0),
1654 IEEE80211_CONF_PS = (1<<1),
1655 IEEE80211_CONF_IDLE = (1<<2),
1656 IEEE80211_CONF_OFFCHANNEL = (1<<3),
1657};
1658
1659
1660/**
1661 * enum ieee80211_conf_changed - denotes which configuration changed
1662 *
1663 * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
1664 * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed
1665 * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
1666 * @IEEE80211_CONF_CHANGE_POWER: the TX power changed
1667 * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
1668 * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
1669 * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
1670 * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
1671 * Note that this is only valid if channel contexts are not used,
1672 * otherwise each channel context has the number of chains listed.
1673 */
1674enum ieee80211_conf_changed {
1675 IEEE80211_CONF_CHANGE_SMPS = BIT(1),
1676 IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2),
1677 IEEE80211_CONF_CHANGE_MONITOR = BIT(3),
1678 IEEE80211_CONF_CHANGE_PS = BIT(4),
1679 IEEE80211_CONF_CHANGE_POWER = BIT(5),
1680 IEEE80211_CONF_CHANGE_CHANNEL = BIT(6),
1681 IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(7),
1682 IEEE80211_CONF_CHANGE_IDLE = BIT(8),
1683};
1684
1685/**
1686 * enum ieee80211_smps_mode - spatial multiplexing power save mode
1687 *
1688 * @IEEE80211_SMPS_AUTOMATIC: automatic
1689 * @IEEE80211_SMPS_OFF: off
1690 * @IEEE80211_SMPS_STATIC: static
1691 * @IEEE80211_SMPS_DYNAMIC: dynamic
1692 * @IEEE80211_SMPS_NUM_MODES: internal, don't use
1693 */
1694enum ieee80211_smps_mode {
1695 IEEE80211_SMPS_AUTOMATIC,
1696 IEEE80211_SMPS_OFF,
1697 IEEE80211_SMPS_STATIC,
1698 IEEE80211_SMPS_DYNAMIC,
1699
1700 /* keep last */
1701 IEEE80211_SMPS_NUM_MODES,
1702};
1703
1704/**
1705 * struct ieee80211_conf - configuration of the device
1706 *
1707 * This struct indicates how the driver shall configure the hardware.
1708 *
1709 * @flags: configuration flags defined above
1710 *
1711 * @listen_interval: listen interval in units of beacon interval
1712 * @ps_dtim_period: The DTIM period of the AP we're connected to, for use
1713 * in power saving. Power saving will not be enabled until a beacon
1714 * has been received and the DTIM period is known.
1715 * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
1716 * powersave documentation below. This variable is valid only when
1717 * the CONF_PS flag is set.
1718 *
1719 * @power_level: requested transmit power (in dBm), backward compatibility
1720 * value only that is set to the minimum of all interfaces
1721 *
1722 * @chandef: the channel definition to tune to
1723 * @radar_enabled: whether radar detection is enabled
1724 *
1725 * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
1726 * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
1727 * but actually means the number of transmissions not the number of retries
1728 * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
1729 * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
1730 * number of transmissions not the number of retries
1731 *
1732 * @smps_mode: spatial multiplexing powersave mode; note that
1733 * %IEEE80211_SMPS_STATIC is used when the device is not
1734 * configured for an HT channel.
1735 * Note that this is only valid if channel contexts are not used,
1736 * otherwise each channel context has the number of chains listed.
1737 */
1738struct ieee80211_conf {
1739 u32 flags;
1740 int power_level, dynamic_ps_timeout;
1741
1742 u16 listen_interval;
1743 u8 ps_dtim_period;
1744
1745 u8 long_frame_max_tx_count, short_frame_max_tx_count;
1746
1747 struct cfg80211_chan_def chandef;
1748 bool radar_enabled;
1749 enum ieee80211_smps_mode smps_mode;
1750};
1751
1752/**
1753 * struct ieee80211_channel_switch - holds the channel switch data
1754 *
1755 * The information provided in this structure is required for channel switch
1756 * operation.
1757 *
1758 * @timestamp: value in microseconds of the 64-bit Time Synchronization
1759 * Function (TSF) timer when the frame containing the channel switch
1760 * announcement was received. This is simply the rx.mactime parameter
1761 * the driver passed into mac80211.
1762 * @device_timestamp: arbitrary timestamp for the device, this is the
1763 * rx.device_timestamp parameter the driver passed to mac80211.
1764 * @block_tx: Indicates whether transmission must be blocked before the
1765 * scheduled channel switch, as indicated by the AP.
1766 * @chandef: the new channel to switch to
1767 * @count: the number of TBTT's until the channel switch event
1768 * @delay: maximum delay between the time the AP transmitted the last beacon in
1769 * current channel and the expected time of the first beacon in the new
1770 * channel, expressed in TU.
1771 * @link_id: the link ID of the link doing the channel switch, 0 for non-MLO
1772 */
1773struct ieee80211_channel_switch {
1774 u64 timestamp;
1775 u32 device_timestamp;
1776 bool block_tx;
1777 struct cfg80211_chan_def chandef;
1778 u8 count;
1779 u8 link_id;
1780 u32 delay;
1781};
1782
1783/**
1784 * enum ieee80211_vif_flags - virtual interface flags
1785 *
1786 * @IEEE80211_VIF_BEACON_FILTER: the device performs beacon filtering
1787 * on this virtual interface to avoid unnecessary CPU wakeups
1788 * @IEEE80211_VIF_SUPPORTS_CQM_RSSI: the device can do connection quality
1789 * monitoring on this virtual interface -- i.e. it can monitor
1790 * connection quality related parameters, such as the RSSI level and
1791 * provide notifications if configured trigger levels are reached.
1792 * @IEEE80211_VIF_SUPPORTS_UAPSD: The device can do U-APSD for this
1793 * interface. This flag should be set during interface addition,
1794 * but may be set/cleared as late as authentication to an AP. It is
1795 * only valid for managed/station mode interfaces.
1796 * @IEEE80211_VIF_GET_NOA_UPDATE: request to handle NOA attributes
1797 * and send P2P_PS notification to the driver if NOA changed, even
1798 * this is not pure P2P vif.
1799 * @IEEE80211_VIF_EML_ACTIVE: The driver indicates that EML operation is
1800 * enabled for the interface.
1801 * @IEEE80211_VIF_IGNORE_OFDMA_WIDER_BW: Ignore wider bandwidth OFDMA
1802 * operation on this interface and request a channel context without
1803 * the AP definition. Use this e.g. because the device is able to
1804 * handle OFDMA (downlink and trigger for uplink) on a per-AP basis.
1805 */
1806enum ieee80211_vif_flags {
1807 IEEE80211_VIF_BEACON_FILTER = BIT(0),
1808 IEEE80211_VIF_SUPPORTS_CQM_RSSI = BIT(1),
1809 IEEE80211_VIF_SUPPORTS_UAPSD = BIT(2),
1810 IEEE80211_VIF_GET_NOA_UPDATE = BIT(3),
1811 IEEE80211_VIF_EML_ACTIVE = BIT(4),
1812 IEEE80211_VIF_IGNORE_OFDMA_WIDER_BW = BIT(5),
1813};
1814
1815
1816/**
1817 * enum ieee80211_offload_flags - virtual interface offload flags
1818 *
1819 * @IEEE80211_OFFLOAD_ENCAP_ENABLED: tx encapsulation offload is enabled
1820 * The driver supports sending frames passed as 802.3 frames by mac80211.
1821 * It must also support sending 802.11 packets for the same interface.
1822 * @IEEE80211_OFFLOAD_ENCAP_4ADDR: support 4-address mode encapsulation offload
1823 * @IEEE80211_OFFLOAD_DECAP_ENABLED: rx encapsulation offload is enabled
1824 * The driver supports passing received 802.11 frames as 802.3 frames to
1825 * mac80211.
1826 */
1827
1828enum ieee80211_offload_flags {
1829 IEEE80211_OFFLOAD_ENCAP_ENABLED = BIT(0),
1830 IEEE80211_OFFLOAD_ENCAP_4ADDR = BIT(1),
1831 IEEE80211_OFFLOAD_DECAP_ENABLED = BIT(2),
1832};
1833
1834/**
1835 * struct ieee80211_vif_cfg - interface configuration
1836 * @assoc: association status
1837 * @ibss_joined: indicates whether this station is part of an IBSS or not
1838 * @ibss_creator: indicates if a new IBSS network is being created
1839 * @ps: power-save mode (STA only). This flag is NOT affected by
1840 * offchannel/dynamic_ps operations.
1841 * @aid: association ID number, valid only when @assoc is true
1842 * @eml_cap: EML capabilities as described in P802.11be_D4.1 Figure 9-1001j.
1843 * @eml_med_sync_delay: Medium Synchronization delay as described in
1844 * P802.11be_D4.1 Figure 9-1001i.
1845 * @mld_capa_op: MLD Capabilities and Operations per P802.11be_D4.1
1846 * Figure 9-1001k
1847 * @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The
1848 * may filter ARP queries targeted for other addresses than listed here.
1849 * The driver must allow ARP queries targeted for all address listed here
1850 * to pass through. An empty list implies no ARP queries need to pass.
1851 * @arp_addr_cnt: Number of addresses currently on the list. Note that this
1852 * may be larger than %IEEE80211_BSS_ARP_ADDR_LIST_LEN (the arp_addr_list
1853 * array size), it's up to the driver what to do in that case.
1854 * @ssid: The SSID of the current vif. Valid in AP and IBSS mode.
1855 * @ssid_len: Length of SSID given in @ssid.
1856 * @s1g: BSS is S1G BSS (affects Association Request format).
1857 * @idle: This interface is idle. There's also a global idle flag in the
1858 * hardware config which may be more appropriate depending on what
1859 * your driver/device needs to do.
1860 * @ap_addr: AP MLD address, or BSSID for non-MLO connections
1861 * (station mode only)
1862 */
1863struct ieee80211_vif_cfg {
1864 /* association related data */
1865 bool assoc, ibss_joined;
1866 bool ibss_creator;
1867 bool ps;
1868 u16 aid;
1869 u16 eml_cap;
1870 u16 eml_med_sync_delay;
1871 u16 mld_capa_op;
1872
1873 __be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN];
1874 int arp_addr_cnt;
1875 u8 ssid[IEEE80211_MAX_SSID_LEN];
1876 size_t ssid_len;
1877 bool s1g;
1878 bool idle;
1879 u8 ap_addr[ETH_ALEN] __aligned(2);
1880};
1881
1882#define IEEE80211_TTLM_NUM_TIDS 8
1883
1884/**
1885 * struct ieee80211_neg_ttlm - negotiated TID to link map info
1886 *
1887 * @downlink: bitmap of active links per TID for downlink, or 0 if mapping for
1888 * this TID is not included.
1889 * @uplink: bitmap of active links per TID for uplink, or 0 if mapping for this
1890 * TID is not included.
1891 * @valid: info is valid or not.
1892 */
1893struct ieee80211_neg_ttlm {
1894 u16 downlink[IEEE80211_TTLM_NUM_TIDS];
1895 u16 uplink[IEEE80211_TTLM_NUM_TIDS];
1896 bool valid;
1897};
1898
1899/**
1900 * enum ieee80211_neg_ttlm_res - return value for negotiated TTLM handling
1901 * @NEG_TTLM_RES_ACCEPT: accept the request
1902 * @NEG_TTLM_RES_REJECT: reject the request
1903 * @NEG_TTLM_RES_SUGGEST_PREFERRED: reject and suggest a new mapping
1904 */
1905enum ieee80211_neg_ttlm_res {
1906 NEG_TTLM_RES_ACCEPT,
1907 NEG_TTLM_RES_REJECT,
1908 NEG_TTLM_RES_SUGGEST_PREFERRED
1909};
1910
1911/**
1912 * struct ieee80211_vif - per-interface data
1913 *
1914 * Data in this structure is continually present for driver
1915 * use during the life of a virtual interface.
1916 *
1917 * @type: type of this virtual interface
1918 * @cfg: vif configuration, see &struct ieee80211_vif_cfg
1919 * @bss_conf: BSS configuration for this interface, either our own
1920 * or the BSS we're associated to
1921 * @link_conf: in case of MLD, the per-link BSS configuration,
1922 * indexed by link ID
1923 * @valid_links: bitmap of valid links, or 0 for non-MLO.
1924 * @active_links: The bitmap of active links, or 0 for non-MLO.
1925 * The driver shouldn't change this directly, but use the
1926 * API calls meant for that purpose.
1927 * @dormant_links: bitmap of valid but disabled links, or 0 for non-MLO.
1928 * Must be a subset of valid_links.
1929 * @suspended_links: subset of dormant_links representing links that are
1930 * suspended.
1931 * 0 for non-MLO.
1932 * @neg_ttlm: negotiated TID to link mapping info.
1933 * see &struct ieee80211_neg_ttlm.
1934 * @addr: address of this interface
1935 * @p2p: indicates whether this AP or STA interface is a p2p
1936 * interface, i.e. a GO or p2p-sta respectively
1937 * @netdev_features: tx netdev features supported by the hardware for this
1938 * vif. mac80211 initializes this to hw->netdev_features, and the driver
1939 * can mask out specific tx features. mac80211 will handle software fixup
1940 * for masked offloads (GSO, CSUM)
1941 * @driver_flags: flags/capabilities the driver has for this interface,
1942 * these need to be set (or cleared) when the interface is added
1943 * or, if supported by the driver, the interface type is changed
1944 * at runtime, mac80211 will never touch this field
1945 * @offload_flags: hardware offload capabilities/flags for this interface.
1946 * These are initialized by mac80211 before calling .add_interface,
1947 * .change_interface or .update_vif_offload and updated by the driver
1948 * within these ops, based on supported features or runtime change
1949 * restrictions.
1950 * @hw_queue: hardware queue for each AC
1951 * @cab_queue: content-after-beacon (DTIM beacon really) queue, AP mode only
1952 * @debugfs_dir: debugfs dentry, can be used by drivers to create own per
1953 * interface debug files. Note that it will be NULL for the virtual
1954 * monitor interface (if that is requested.)
1955 * @probe_req_reg: probe requests should be reported to mac80211 for this
1956 * interface.
1957 * @rx_mcast_action_reg: multicast Action frames should be reported to mac80211
1958 * for this interface.
1959 * @drv_priv: data area for driver use, will always be aligned to
1960 * sizeof(void \*).
1961 * @txq: the multicast data TX queue
1962 * @offload_flags: 802.3 -> 802.11 enapsulation offload flags, see
1963 * &enum ieee80211_offload_flags.
1964 * @mbssid_tx_vif: Pointer to the transmitting interface if MBSSID is enabled.
1965 */
1966struct ieee80211_vif {
1967 enum nl80211_iftype type;
1968 struct ieee80211_vif_cfg cfg;
1969 struct ieee80211_bss_conf bss_conf;
1970 struct ieee80211_bss_conf __rcu *link_conf[IEEE80211_MLD_MAX_NUM_LINKS];
1971 u16 valid_links, active_links, dormant_links, suspended_links;
1972 struct ieee80211_neg_ttlm neg_ttlm;
1973 u8 addr[ETH_ALEN] __aligned(2);
1974 bool p2p;
1975
1976 u8 cab_queue;
1977 u8 hw_queue[IEEE80211_NUM_ACS];
1978
1979 struct ieee80211_txq *txq;
1980
1981 netdev_features_t netdev_features;
1982 u32 driver_flags;
1983 u32 offload_flags;
1984
1985#ifdef CONFIG_MAC80211_DEBUGFS
1986 struct dentry *debugfs_dir;
1987#endif
1988
1989 bool probe_req_reg;
1990 bool rx_mcast_action_reg;
1991
1992 struct ieee80211_vif *mbssid_tx_vif;
1993
1994 /* must be last */
1995 u8 drv_priv[] __aligned(sizeof(void *));
1996};
1997
1998/**
1999 * ieee80211_vif_usable_links - Return the usable links for the vif
2000 * @vif: the vif for which the usable links are requested
2001 * Return: the usable link bitmap
2002 */
2003static inline u16 ieee80211_vif_usable_links(const struct ieee80211_vif *vif)
2004{
2005 return vif->valid_links & ~vif->dormant_links;
2006}
2007
2008/**
2009 * ieee80211_vif_is_mld - Returns true iff the vif is an MLD one
2010 * @vif: the vif
2011 * Return: %true if the vif is an MLD, %false otherwise.
2012 */
2013static inline bool ieee80211_vif_is_mld(const struct ieee80211_vif *vif)
2014{
2015 /* valid_links != 0 indicates this vif is an MLD */
2016 return vif->valid_links != 0;
2017}
2018
2019/**
2020 * ieee80211_vif_link_active - check if a given link is active
2021 * @vif: the vif
2022 * @link_id: the link ID to check
2023 * Return: %true if the vif is an MLD and the link is active, or if
2024 * the vif is not an MLD and the link ID is 0; %false otherwise.
2025 */
2026static inline bool ieee80211_vif_link_active(const struct ieee80211_vif *vif,
2027 unsigned int link_id)
2028{
2029 if (!ieee80211_vif_is_mld(vif))
2030 return link_id == 0;
2031 return vif->active_links & BIT(link_id);
2032}
2033
2034#define for_each_vif_active_link(vif, link, link_id) \
2035 for (link_id = 0; link_id < ARRAY_SIZE((vif)->link_conf); link_id++) \
2036 if ((!(vif)->active_links || \
2037 (vif)->active_links & BIT(link_id)) && \
2038 (link = link_conf_dereference_check(vif, link_id)))
2039
2040static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
2041{
2042#ifdef CONFIG_MAC80211_MESH
2043 return vif->type == NL80211_IFTYPE_MESH_POINT;
2044#endif
2045 return false;
2046}
2047
2048/**
2049 * wdev_to_ieee80211_vif - return a vif struct from a wdev
2050 * @wdev: the wdev to get the vif for
2051 *
2052 * This can be used by mac80211 drivers with direct cfg80211 APIs
2053 * (like the vendor commands) that get a wdev.
2054 *
2055 * Note that this function may return %NULL if the given wdev isn't
2056 * associated with a vif that the driver knows about (e.g. monitor
2057 * or AP_VLAN interfaces.)
2058 */
2059struct ieee80211_vif *wdev_to_ieee80211_vif(struct wireless_dev *wdev);
2060
2061/**
2062 * ieee80211_vif_to_wdev - return a wdev struct from a vif
2063 * @vif: the vif to get the wdev for
2064 *
2065 * This can be used by mac80211 drivers with direct cfg80211 APIs
2066 * (like the vendor commands) that needs to get the wdev for a vif.
2067 * This can also be useful to get the netdev associated to a vif.
2068 */
2069struct wireless_dev *ieee80211_vif_to_wdev(struct ieee80211_vif *vif);
2070
2071static inline bool lockdep_vif_wiphy_mutex_held(struct ieee80211_vif *vif)
2072{
2073 return lockdep_is_held(&ieee80211_vif_to_wdev(vif)->wiphy->mtx);
2074}
2075
2076#define link_conf_dereference_protected(vif, link_id) \
2077 rcu_dereference_protected((vif)->link_conf[link_id], \
2078 lockdep_vif_wiphy_mutex_held(vif))
2079
2080#define link_conf_dereference_check(vif, link_id) \
2081 rcu_dereference_check((vif)->link_conf[link_id], \
2082 lockdep_vif_wiphy_mutex_held(vif))
2083
2084/**
2085 * enum ieee80211_key_flags - key flags
2086 *
2087 * These flags are used for communication about keys between the driver
2088 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
2089 *
2090 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
2091 * driver to indicate that it requires IV generation for this
2092 * particular key. Setting this flag does not necessarily mean that SKBs
2093 * will have sufficient tailroom for ICV or MIC.
2094 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
2095 * the driver for a TKIP key if it requires Michael MIC
2096 * generation in software.
2097 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
2098 * that the key is pairwise rather then a shared key.
2099 * @IEEE80211_KEY_FLAG_SW_MGMT_TX: This flag should be set by the driver for a
2100 * CCMP/GCMP key if it requires CCMP/GCMP encryption of management frames
2101 * (MFP) to be done in software.
2102 * @IEEE80211_KEY_FLAG_PUT_IV_SPACE: This flag should be set by the driver
2103 * if space should be prepared for the IV, but the IV
2104 * itself should not be generated. Do not set together with
2105 * @IEEE80211_KEY_FLAG_GENERATE_IV on the same key. Setting this flag does
2106 * not necessarily mean that SKBs will have sufficient tailroom for ICV or
2107 * MIC.
2108 * @IEEE80211_KEY_FLAG_RX_MGMT: This key will be used to decrypt received
2109 * management frames. The flag can help drivers that have a hardware
2110 * crypto implementation that doesn't deal with management frames
2111 * properly by allowing them to not upload the keys to hardware and
2112 * fall back to software crypto. Note that this flag deals only with
2113 * RX, if your crypto engine can't deal with TX you can also set the
2114 * %IEEE80211_KEY_FLAG_SW_MGMT_TX flag to encrypt such frames in SW.
2115 * @IEEE80211_KEY_FLAG_GENERATE_IV_MGMT: This flag should be set by the
2116 * driver for a CCMP/GCMP key to indicate that is requires IV generation
2117 * only for management frames (MFP).
2118 * @IEEE80211_KEY_FLAG_RESERVE_TAILROOM: This flag should be set by the
2119 * driver for a key to indicate that sufficient tailroom must always
2120 * be reserved for ICV or MIC, even when HW encryption is enabled.
2121 * @IEEE80211_KEY_FLAG_PUT_MIC_SPACE: This flag should be set by the driver for
2122 * a TKIP key if it only requires MIC space. Do not set together with
2123 * @IEEE80211_KEY_FLAG_GENERATE_MMIC on the same key.
2124 * @IEEE80211_KEY_FLAG_NO_AUTO_TX: Key needs explicit Tx activation.
2125 * @IEEE80211_KEY_FLAG_GENERATE_MMIE: This flag should be set by the driver
2126 * for a AES_CMAC key to indicate that it requires sequence number
2127 * generation only
2128 * @IEEE80211_KEY_FLAG_SPP_AMSDU: SPP A-MSDUs can be used with this key
2129 * (set by mac80211 from the sta->spp_amsdu flag)
2130 */
2131enum ieee80211_key_flags {
2132 IEEE80211_KEY_FLAG_GENERATE_IV_MGMT = BIT(0),
2133 IEEE80211_KEY_FLAG_GENERATE_IV = BIT(1),
2134 IEEE80211_KEY_FLAG_GENERATE_MMIC = BIT(2),
2135 IEEE80211_KEY_FLAG_PAIRWISE = BIT(3),
2136 IEEE80211_KEY_FLAG_SW_MGMT_TX = BIT(4),
2137 IEEE80211_KEY_FLAG_PUT_IV_SPACE = BIT(5),
2138 IEEE80211_KEY_FLAG_RX_MGMT = BIT(6),
2139 IEEE80211_KEY_FLAG_RESERVE_TAILROOM = BIT(7),
2140 IEEE80211_KEY_FLAG_PUT_MIC_SPACE = BIT(8),
2141 IEEE80211_KEY_FLAG_NO_AUTO_TX = BIT(9),
2142 IEEE80211_KEY_FLAG_GENERATE_MMIE = BIT(10),
2143 IEEE80211_KEY_FLAG_SPP_AMSDU = BIT(11),
2144};
2145
2146/**
2147 * struct ieee80211_key_conf - key information
2148 *
2149 * This key information is given by mac80211 to the driver by
2150 * the set_key() callback in &struct ieee80211_ops.
2151 *
2152 * @hw_key_idx: To be set by the driver, this is the key index the driver
2153 * wants to be given when a frame is transmitted and needs to be
2154 * encrypted in hardware.
2155 * @cipher: The key's cipher suite selector.
2156 * @tx_pn: PN used for TX keys, may be used by the driver as well if it
2157 * needs to do software PN assignment by itself (e.g. due to TSO)
2158 * @flags: key flags, see &enum ieee80211_key_flags.
2159 * @keyidx: the key index (0-3)
2160 * @keylen: key material length
2161 * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
2162 * data block:
2163 * - Temporal Encryption Key (128 bits)
2164 * - Temporal Authenticator Tx MIC Key (64 bits)
2165 * - Temporal Authenticator Rx MIC Key (64 bits)
2166 * @icv_len: The ICV length for this key type
2167 * @iv_len: The IV length for this key type
2168 * @link_id: the link ID for MLO, or -1 for non-MLO or pairwise keys
2169 */
2170struct ieee80211_key_conf {
2171 atomic64_t tx_pn;
2172 u32 cipher;
2173 u8 icv_len;
2174 u8 iv_len;
2175 u8 hw_key_idx;
2176 s8 keyidx;
2177 u16 flags;
2178 s8 link_id;
2179 u8 keylen;
2180 u8 key[];
2181};
2182
2183#define IEEE80211_MAX_PN_LEN 16
2184
2185#define TKIP_PN_TO_IV16(pn) ((u16)(pn & 0xffff))
2186#define TKIP_PN_TO_IV32(pn) ((u32)((pn >> 16) & 0xffffffff))
2187
2188/**
2189 * struct ieee80211_key_seq - key sequence counter
2190 *
2191 * @tkip: TKIP data, containing IV32 and IV16 in host byte order
2192 * @ccmp: PN data, most significant byte first (big endian,
2193 * reverse order than in packet)
2194 * @aes_cmac: PN data, most significant byte first (big endian,
2195 * reverse order than in packet)
2196 * @aes_gmac: PN data, most significant byte first (big endian,
2197 * reverse order than in packet)
2198 * @gcmp: PN data, most significant byte first (big endian,
2199 * reverse order than in packet)
2200 * @hw: data for HW-only (e.g. cipher scheme) keys
2201 */
2202struct ieee80211_key_seq {
2203 union {
2204 struct {
2205 u32 iv32;
2206 u16 iv16;
2207 } tkip;
2208 struct {
2209 u8 pn[6];
2210 } ccmp;
2211 struct {
2212 u8 pn[6];
2213 } aes_cmac;
2214 struct {
2215 u8 pn[6];
2216 } aes_gmac;
2217 struct {
2218 u8 pn[6];
2219 } gcmp;
2220 struct {
2221 u8 seq[IEEE80211_MAX_PN_LEN];
2222 u8 seq_len;
2223 } hw;
2224 };
2225};
2226
2227/**
2228 * enum set_key_cmd - key command
2229 *
2230 * Used with the set_key() callback in &struct ieee80211_ops, this
2231 * indicates whether a key is being removed or added.
2232 *
2233 * @SET_KEY: a key is set
2234 * @DISABLE_KEY: a key must be disabled
2235 */
2236enum set_key_cmd {
2237 SET_KEY, DISABLE_KEY,
2238};
2239
2240/**
2241 * enum ieee80211_sta_state - station state
2242 *
2243 * @IEEE80211_STA_NOTEXIST: station doesn't exist at all,
2244 * this is a special state for add/remove transitions
2245 * @IEEE80211_STA_NONE: station exists without special state
2246 * @IEEE80211_STA_AUTH: station is authenticated
2247 * @IEEE80211_STA_ASSOC: station is associated
2248 * @IEEE80211_STA_AUTHORIZED: station is authorized (802.1X)
2249 */
2250enum ieee80211_sta_state {
2251 /* NOTE: These need to be ordered correctly! */
2252 IEEE80211_STA_NOTEXIST,
2253 IEEE80211_STA_NONE,
2254 IEEE80211_STA_AUTH,
2255 IEEE80211_STA_ASSOC,
2256 IEEE80211_STA_AUTHORIZED,
2257};
2258
2259/**
2260 * enum ieee80211_sta_rx_bandwidth - station RX bandwidth
2261 * @IEEE80211_STA_RX_BW_20: station can only receive 20 MHz
2262 * @IEEE80211_STA_RX_BW_40: station can receive up to 40 MHz
2263 * @IEEE80211_STA_RX_BW_80: station can receive up to 80 MHz
2264 * @IEEE80211_STA_RX_BW_160: station can receive up to 160 MHz
2265 * (including 80+80 MHz)
2266 * @IEEE80211_STA_RX_BW_320: station can receive up to 320 MHz
2267 *
2268 * Implementation note: 20 must be zero to be initialized
2269 * correctly, the values must be sorted.
2270 */
2271enum ieee80211_sta_rx_bandwidth {
2272 IEEE80211_STA_RX_BW_20 = 0,
2273 IEEE80211_STA_RX_BW_40,
2274 IEEE80211_STA_RX_BW_80,
2275 IEEE80211_STA_RX_BW_160,
2276 IEEE80211_STA_RX_BW_320,
2277};
2278
2279/**
2280 * struct ieee80211_sta_rates - station rate selection table
2281 *
2282 * @rcu_head: RCU head used for freeing the table on update
2283 * @rate: transmit rates/flags to be used by default.
2284 * Overriding entries per-packet is possible by using cb tx control.
2285 */
2286struct ieee80211_sta_rates {
2287 struct rcu_head rcu_head;
2288 struct {
2289 s8 idx;
2290 u8 count;
2291 u8 count_cts;
2292 u8 count_rts;
2293 u16 flags;
2294 } rate[IEEE80211_TX_RATE_TABLE_SIZE];
2295};
2296
2297/**
2298 * struct ieee80211_sta_txpwr - station txpower configuration
2299 *
2300 * Used to configure txpower for station.
2301 *
2302 * @power: indicates the tx power, in dBm, to be used when sending data frames
2303 * to the STA.
2304 * @type: In particular if TPC %type is NL80211_TX_POWER_LIMITED then tx power
2305 * will be less than or equal to specified from userspace, whereas if TPC
2306 * %type is NL80211_TX_POWER_AUTOMATIC then it indicates default tx power.
2307 * NL80211_TX_POWER_FIXED is not a valid configuration option for
2308 * per peer TPC.
2309 */
2310struct ieee80211_sta_txpwr {
2311 s16 power;
2312 enum nl80211_tx_power_setting type;
2313};
2314
2315/**
2316 * struct ieee80211_sta_aggregates - info that is aggregated from active links
2317 *
2318 * Used for any per-link data that needs to be aggregated and updated in the
2319 * main &struct ieee80211_sta when updated or the active links change.
2320 *
2321 * @max_amsdu_len: indicates the maximal length of an A-MSDU in bytes.
2322 * This field is always valid for packets with a VHT preamble.
2323 * For packets with a HT preamble, additional limits apply:
2324 *
2325 * * If the skb is transmitted as part of a BA agreement, the
2326 * A-MSDU maximal size is min(max_amsdu_len, 4065) bytes.
2327 * * If the skb is not part of a BA agreement, the A-MSDU maximal
2328 * size is min(max_amsdu_len, 7935) bytes.
2329 *
2330 * Both additional HT limits must be enforced by the low level
2331 * driver. This is defined by the spec (IEEE 802.11-2012 section
2332 * 8.3.2.2 NOTE 2).
2333 * @max_rc_amsdu_len: Maximum A-MSDU size in bytes recommended by rate control.
2334 * @max_tid_amsdu_len: Maximum A-MSDU size in bytes for this TID
2335 */
2336struct ieee80211_sta_aggregates {
2337 u16 max_amsdu_len;
2338
2339 u16 max_rc_amsdu_len;
2340 u16 max_tid_amsdu_len[IEEE80211_NUM_TIDS];
2341};
2342
2343/**
2344 * struct ieee80211_link_sta - station Link specific info
2345 * All link specific info for a STA link for a non MLD STA(single)
2346 * or a MLD STA(multiple entries) are stored here.
2347 *
2348 * @sta: reference to owning STA
2349 * @addr: MAC address of the Link STA. For non-MLO STA this is same as the addr
2350 * in ieee80211_sta. For MLO Link STA this addr can be same or different
2351 * from addr in ieee80211_sta (representing MLD STA addr)
2352 * @link_id: the link ID for this link STA (0 for deflink)
2353 * @smps_mode: current SMPS mode (off, static or dynamic)
2354 * @supp_rates: Bitmap of supported rates
2355 * @ht_cap: HT capabilities of this STA; restricted to our own capabilities
2356 * @vht_cap: VHT capabilities of this STA; restricted to our own capabilities
2357 * @he_cap: HE capabilities of this STA
2358 * @he_6ghz_capa: on 6 GHz, holds the HE 6 GHz band capabilities
2359 * @eht_cap: EHT capabilities of this STA
2360 * @agg: per-link data for multi-link aggregation
2361 * @bandwidth: current bandwidth the station can receive with
2362 * @rx_nss: in HT/VHT, the maximum number of spatial streams the
2363 * station can receive at the moment, changed by operating mode
2364 * notifications and capabilities. The value is only valid after
2365 * the station moves to associated state.
2366 * @txpwr: the station tx power configuration
2367 *
2368 */
2369struct ieee80211_link_sta {
2370 struct ieee80211_sta *sta;
2371
2372 u8 addr[ETH_ALEN];
2373 u8 link_id;
2374 enum ieee80211_smps_mode smps_mode;
2375
2376 u32 supp_rates[NUM_NL80211_BANDS];
2377 struct ieee80211_sta_ht_cap ht_cap;
2378 struct ieee80211_sta_vht_cap vht_cap;
2379 struct ieee80211_sta_he_cap he_cap;
2380 struct ieee80211_he_6ghz_capa he_6ghz_capa;
2381 struct ieee80211_sta_eht_cap eht_cap;
2382
2383 struct ieee80211_sta_aggregates agg;
2384
2385 u8 rx_nss;
2386 enum ieee80211_sta_rx_bandwidth bandwidth;
2387 struct ieee80211_sta_txpwr txpwr;
2388};
2389
2390/**
2391 * struct ieee80211_sta - station table entry
2392 *
2393 * A station table entry represents a station we are possibly
2394 * communicating with. Since stations are RCU-managed in
2395 * mac80211, any ieee80211_sta pointer you get access to must
2396 * either be protected by rcu_read_lock() explicitly or implicitly,
2397 * or you must take good care to not use such a pointer after a
2398 * call to your sta_remove callback that removed it.
2399 * This also represents the MLD STA in case of MLO association
2400 * and holds pointers to various link STA's
2401 *
2402 * @addr: MAC address
2403 * @aid: AID we assigned to the station if we're an AP
2404 * @max_rx_aggregation_subframes: maximal amount of frames in a single AMPDU
2405 * that this station is allowed to transmit to us.
2406 * Can be modified by driver.
2407 * @wme: indicates whether the STA supports QoS/WME (if local devices does,
2408 * otherwise always false)
2409 * @drv_priv: data area for driver use, will always be aligned to
2410 * sizeof(void \*), size is determined in hw information.
2411 * @uapsd_queues: bitmap of queues configured for uapsd. Only valid
2412 * if wme is supported. The bits order is like in
2413 * IEEE80211_WMM_IE_STA_QOSINFO_AC_*.
2414 * @max_sp: max Service Period. Only valid if wme is supported.
2415 * @rates: rate control selection table
2416 * @tdls: indicates whether the STA is a TDLS peer
2417 * @tdls_initiator: indicates the STA is an initiator of the TDLS link. Only
2418 * valid if the STA is a TDLS peer in the first place.
2419 * @mfp: indicates whether the STA uses management frame protection or not.
2420 * @mlo: indicates whether the STA is MLO station.
2421 * @max_amsdu_subframes: indicates the maximal number of MSDUs in a single
2422 * A-MSDU. Taken from the Extended Capabilities element. 0 means
2423 * unlimited.
2424 * @cur: currently valid data as aggregated from the active links
2425 * For non MLO STA it will point to the deflink data. For MLO STA
2426 * ieee80211_sta_recalc_aggregates() must be called to update it.
2427 * @support_p2p_ps: indicates whether the STA supports P2P PS mechanism or not.
2428 * @txq: per-TID data TX queues; note that the last entry (%IEEE80211_NUM_TIDS)
2429 * is used for non-data frames
2430 * @deflink: This holds the default link STA information, for non MLO STA all link
2431 * specific STA information is accessed through @deflink or through
2432 * link[0] which points to address of @deflink. For MLO Link STA
2433 * the first added link STA will point to deflink.
2434 * @link: reference to Link Sta entries. For Non MLO STA, except 1st link,
2435 * i.e link[0] all links would be assigned to NULL by default and
2436 * would access link information via @deflink or link[0]. For MLO
2437 * STA, first link STA being added will point its link pointer to
2438 * @deflink address and remaining would be allocated and the address
2439 * would be assigned to link[link_id] where link_id is the id assigned
2440 * by the AP.
2441 * @valid_links: bitmap of valid links, or 0 for non-MLO
2442 * @spp_amsdu: indicates whether the STA uses SPP A-MSDU or not.
2443 */
2444struct ieee80211_sta {
2445 u8 addr[ETH_ALEN];
2446 u16 aid;
2447 u16 max_rx_aggregation_subframes;
2448 bool wme;
2449 u8 uapsd_queues;
2450 u8 max_sp;
2451 struct ieee80211_sta_rates __rcu *rates;
2452 bool tdls;
2453 bool tdls_initiator;
2454 bool mfp;
2455 bool mlo;
2456 bool spp_amsdu;
2457 u8 max_amsdu_subframes;
2458
2459 struct ieee80211_sta_aggregates *cur;
2460
2461 bool support_p2p_ps;
2462
2463 struct ieee80211_txq *txq[IEEE80211_NUM_TIDS + 1];
2464
2465 u16 valid_links;
2466 struct ieee80211_link_sta deflink;
2467 struct ieee80211_link_sta __rcu *link[IEEE80211_MLD_MAX_NUM_LINKS];
2468
2469 /* must be last */
2470 u8 drv_priv[] __aligned(sizeof(void *));
2471};
2472
2473#ifdef CONFIG_LOCKDEP
2474bool lockdep_sta_mutex_held(struct ieee80211_sta *pubsta);
2475#else
2476static inline bool lockdep_sta_mutex_held(struct ieee80211_sta *pubsta)
2477{
2478 return true;
2479}
2480#endif
2481
2482#define link_sta_dereference_protected(sta, link_id) \
2483 rcu_dereference_protected((sta)->link[link_id], \
2484 lockdep_sta_mutex_held(sta))
2485
2486#define link_sta_dereference_check(sta, link_id) \
2487 rcu_dereference_check((sta)->link[link_id], \
2488 lockdep_sta_mutex_held(sta))
2489
2490#define for_each_sta_active_link(vif, sta, link_sta, link_id) \
2491 for (link_id = 0; link_id < ARRAY_SIZE((sta)->link); link_id++) \
2492 if ((!(vif)->active_links || \
2493 (vif)->active_links & BIT(link_id)) && \
2494 ((link_sta) = link_sta_dereference_check(sta, link_id)))
2495
2496/**
2497 * enum sta_notify_cmd - sta notify command
2498 *
2499 * Used with the sta_notify() callback in &struct ieee80211_ops, this
2500 * indicates if an associated station made a power state transition.
2501 *
2502 * @STA_NOTIFY_SLEEP: a station is now sleeping
2503 * @STA_NOTIFY_AWAKE: a sleeping station woke up
2504 */
2505enum sta_notify_cmd {
2506 STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
2507};
2508
2509/**
2510 * struct ieee80211_tx_control - TX control data
2511 *
2512 * @sta: station table entry, this sta pointer may be NULL and
2513 * it is not allowed to copy the pointer, due to RCU.
2514 */
2515struct ieee80211_tx_control {
2516 struct ieee80211_sta *sta;
2517};
2518
2519/**
2520 * struct ieee80211_txq - Software intermediate tx queue
2521 *
2522 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2523 * @sta: station table entry, %NULL for per-vif queue
2524 * @tid: the TID for this queue (unused for per-vif queue),
2525 * %IEEE80211_NUM_TIDS for non-data (if enabled)
2526 * @ac: the AC for this queue
2527 * @drv_priv: driver private area, sized by hw->txq_data_size
2528 *
2529 * The driver can obtain packets from this queue by calling
2530 * ieee80211_tx_dequeue().
2531 */
2532struct ieee80211_txq {
2533 struct ieee80211_vif *vif;
2534 struct ieee80211_sta *sta;
2535 u8 tid;
2536 u8 ac;
2537
2538 /* must be last */
2539 u8 drv_priv[] __aligned(sizeof(void *));
2540};
2541
2542/**
2543 * enum ieee80211_hw_flags - hardware flags
2544 *
2545 * These flags are used to indicate hardware capabilities to
2546 * the stack. Generally, flags here should have their meaning
2547 * done in a way that the simplest hardware doesn't need setting
2548 * any particular flags. There are some exceptions to this rule,
2549 * however, so you are advised to review these flags carefully.
2550 *
2551 * @IEEE80211_HW_HAS_RATE_CONTROL:
2552 * The hardware or firmware includes rate control, and cannot be
2553 * controlled by the stack. As such, no rate control algorithm
2554 * should be instantiated, and the TX rate reported to userspace
2555 * will be taken from the TX status instead of the rate control
2556 * algorithm.
2557 * Note that this requires that the driver implement a number of
2558 * callbacks so it has the correct information, it needs to have
2559 * the @set_rts_threshold callback and must look at the BSS config
2560 * @use_cts_prot for G/N protection, @use_short_slot for slot
2561 * timing in 2.4 GHz and @use_short_preamble for preambles for
2562 * CCK frames.
2563 *
2564 * @IEEE80211_HW_RX_INCLUDES_FCS:
2565 * Indicates that received frames passed to the stack include
2566 * the FCS at the end.
2567 *
2568 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
2569 * Some wireless LAN chipsets buffer broadcast/multicast frames
2570 * for power saving stations in the hardware/firmware and others
2571 * rely on the host system for such buffering. This option is used
2572 * to configure the IEEE 802.11 upper layer to buffer broadcast and
2573 * multicast frames when there are power saving stations so that
2574 * the driver can fetch them with ieee80211_get_buffered_bc().
2575 *
2576 * @IEEE80211_HW_SIGNAL_UNSPEC:
2577 * Hardware can provide signal values but we don't know its units. We
2578 * expect values between 0 and @max_signal.
2579 * If possible please provide dB or dBm instead.
2580 *
2581 * @IEEE80211_HW_SIGNAL_DBM:
2582 * Hardware gives signal values in dBm, decibel difference from
2583 * one milliwatt. This is the preferred method since it is standardized
2584 * between different devices. @max_signal does not need to be set.
2585 *
2586 * @IEEE80211_HW_SPECTRUM_MGMT:
2587 * Hardware supports spectrum management defined in 802.11h
2588 * Measurement, Channel Switch, Quieting, TPC
2589 *
2590 * @IEEE80211_HW_AMPDU_AGGREGATION:
2591 * Hardware supports 11n A-MPDU aggregation.
2592 *
2593 * @IEEE80211_HW_SUPPORTS_PS:
2594 * Hardware has power save support (i.e. can go to sleep).
2595 *
2596 * @IEEE80211_HW_PS_NULLFUNC_STACK:
2597 * Hardware requires nullfunc frame handling in stack, implies
2598 * stack support for dynamic PS.
2599 *
2600 * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
2601 * Hardware has support for dynamic PS.
2602 *
2603 * @IEEE80211_HW_MFP_CAPABLE:
2604 * Hardware supports management frame protection (MFP, IEEE 802.11w).
2605 *
2606 * @IEEE80211_HW_REPORTS_TX_ACK_STATUS:
2607 * Hardware can provide ack status reports of Tx frames to
2608 * the stack.
2609 *
2610 * @IEEE80211_HW_CONNECTION_MONITOR:
2611 * The hardware performs its own connection monitoring, including
2612 * periodic keep-alives to the AP and probing the AP on beacon loss.
2613 *
2614 * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC:
2615 * This device needs to get data from beacon before association (i.e.
2616 * dtim_period).
2617 *
2618 * @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports
2619 * per-station GTKs as used by IBSS RSN or during fast transition. If
2620 * the device doesn't support per-station GTKs, but can be asked not
2621 * to decrypt group addressed frames, then IBSS RSN support is still
2622 * possible but software crypto will be used. Advertise the wiphy flag
2623 * only in that case.
2624 *
2625 * @IEEE80211_HW_AP_LINK_PS: When operating in AP mode the device
2626 * autonomously manages the PS status of connected stations. When
2627 * this flag is set mac80211 will not trigger PS mode for connected
2628 * stations based on the PM bit of incoming frames.
2629 * Use ieee80211_start_ps()/ieee8021_end_ps() to manually configure
2630 * the PS mode of connected stations.
2631 *
2632 * @IEEE80211_HW_TX_AMPDU_SETUP_IN_HW: The device handles TX A-MPDU session
2633 * setup strictly in HW. mac80211 should not attempt to do this in
2634 * software.
2635 *
2636 * @IEEE80211_HW_WANT_MONITOR_VIF: The driver would like to be informed of
2637 * a virtual monitor interface when monitor interfaces are the only
2638 * active interfaces.
2639 *
2640 * @IEEE80211_HW_NO_AUTO_VIF: The driver would like for no wlanX to
2641 * be created. It is expected user-space will create vifs as
2642 * desired (and thus have them named as desired).
2643 *
2644 * @IEEE80211_HW_SW_CRYPTO_CONTROL: The driver wants to control which of the
2645 * crypto algorithms can be done in software - so don't automatically
2646 * try to fall back to it if hardware crypto fails, but do so only if
2647 * the driver returns 1. This also forces the driver to advertise its
2648 * supported cipher suites.
2649 *
2650 * @IEEE80211_HW_SUPPORT_FAST_XMIT: The driver/hardware supports fast-xmit,
2651 * this currently requires only the ability to calculate the duration
2652 * for frames.
2653 *
2654 * @IEEE80211_HW_QUEUE_CONTROL: The driver wants to control per-interface
2655 * queue mapping in order to use different queues (not just one per AC)
2656 * for different virtual interfaces. See the doc section on HW queue
2657 * control for more details.
2658 *
2659 * @IEEE80211_HW_SUPPORTS_RC_TABLE: The driver supports using a rate
2660 * selection table provided by the rate control algorithm.
2661 *
2662 * @IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF: Use the P2P Device address for any
2663 * P2P Interface. This will be honoured even if more than one interface
2664 * is supported.
2665 *
2666 * @IEEE80211_HW_TIMING_BEACON_ONLY: Use sync timing from beacon frames
2667 * only, to allow getting TBTT of a DTIM beacon.
2668 *
2669 * @IEEE80211_HW_SUPPORTS_HT_CCK_RATES: Hardware supports mixing HT/CCK rates
2670 * and can cope with CCK rates in an aggregation session (e.g. by not
2671 * using aggregation for such frames.)
2672 *
2673 * @IEEE80211_HW_CHANCTX_STA_CSA: Support 802.11h based channel-switch (CSA)
2674 * for a single active channel while using channel contexts. When support
2675 * is not enabled the default action is to disconnect when getting the
2676 * CSA frame.
2677 *
2678 * @IEEE80211_HW_SUPPORTS_CLONED_SKBS: The driver will never modify the payload
2679 * or tailroom of TX skbs without copying them first.
2680 *
2681 * @IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS: The HW supports scanning on all bands
2682 * in one command, mac80211 doesn't have to run separate scans per band.
2683 *
2684 * @IEEE80211_HW_TDLS_WIDER_BW: The device/driver supports wider bandwidth
2685 * than then BSS bandwidth for a TDLS link on the base channel.
2686 *
2687 * @IEEE80211_HW_SUPPORTS_AMSDU_IN_AMPDU: The driver supports receiving A-MSDUs
2688 * within A-MPDU.
2689 *
2690 * @IEEE80211_HW_BEACON_TX_STATUS: The device/driver provides TX status
2691 * for sent beacons.
2692 *
2693 * @IEEE80211_HW_NEEDS_UNIQUE_STA_ADDR: Hardware (or driver) requires that each
2694 * station has a unique address, i.e. each station entry can be identified
2695 * by just its MAC address; this prevents, for example, the same station
2696 * from connecting to two virtual AP interfaces at the same time.
2697 *
2698 * @IEEE80211_HW_SUPPORTS_REORDERING_BUFFER: Hardware (or driver) manages the
2699 * reordering buffer internally, guaranteeing mac80211 receives frames in
2700 * order and does not need to manage its own reorder buffer or BA session
2701 * timeout.
2702 *
2703 * @IEEE80211_HW_USES_RSS: The device uses RSS and thus requires parallel RX,
2704 * which implies using per-CPU station statistics.
2705 *
2706 * @IEEE80211_HW_TX_AMSDU: Hardware (or driver) supports software aggregated
2707 * A-MSDU frames. Requires software tx queueing and fast-xmit support.
2708 * When not using minstrel/minstrel_ht rate control, the driver must
2709 * limit the maximum A-MSDU size based on the current tx rate by setting
2710 * max_rc_amsdu_len in struct ieee80211_sta.
2711 *
2712 * @IEEE80211_HW_TX_FRAG_LIST: Hardware (or driver) supports sending frag_list
2713 * skbs, needed for zero-copy software A-MSDU.
2714 *
2715 * @IEEE80211_HW_REPORTS_LOW_ACK: The driver (or firmware) reports low ack event
2716 * by ieee80211_report_low_ack() based on its own algorithm. For such
2717 * drivers, mac80211 packet loss mechanism will not be triggered and driver
2718 * is completely depending on firmware event for station kickout.
2719 *
2720 * @IEEE80211_HW_SUPPORTS_TX_FRAG: Hardware does fragmentation by itself.
2721 * The stack will not do fragmentation.
2722 * The callback for @set_frag_threshold should be set as well.
2723 *
2724 * @IEEE80211_HW_SUPPORTS_TDLS_BUFFER_STA: Hardware supports buffer STA on
2725 * TDLS links.
2726 *
2727 * @IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP: The driver requires the
2728 * mgd_prepare_tx() callback to be called before transmission of a
2729 * deauthentication frame in case the association was completed but no
2730 * beacon was heard. This is required in multi-channel scenarios, where the
2731 * virtual interface might not be given air time for the transmission of
2732 * the frame, as it is not synced with the AP/P2P GO yet, and thus the
2733 * deauthentication frame might not be transmitted.
2734 *
2735 * @IEEE80211_HW_DOESNT_SUPPORT_QOS_NDP: The driver (or firmware) doesn't
2736 * support QoS NDP for AP probing - that's most likely a driver bug.
2737 *
2738 * @IEEE80211_HW_BUFF_MMPDU_TXQ: use the TXQ for bufferable MMPDUs, this of
2739 * course requires the driver to use TXQs to start with.
2740 *
2741 * @IEEE80211_HW_SUPPORTS_VHT_EXT_NSS_BW: (Hardware) rate control supports VHT
2742 * extended NSS BW (dot11VHTExtendedNSSBWCapable). This flag will be set if
2743 * the selected rate control algorithm sets %RATE_CTRL_CAPA_VHT_EXT_NSS_BW
2744 * but if the rate control is built-in then it must be set by the driver.
2745 * See also the documentation for that flag.
2746 *
2747 * @IEEE80211_HW_STA_MMPDU_TXQ: use the extra non-TID per-station TXQ for all
2748 * MMPDUs on station interfaces. This of course requires the driver to use
2749 * TXQs to start with.
2750 *
2751 * @IEEE80211_HW_TX_STATUS_NO_AMPDU_LEN: Driver does not report accurate A-MPDU
2752 * length in tx status information
2753 *
2754 * @IEEE80211_HW_SUPPORTS_MULTI_BSSID: Hardware supports multi BSSID
2755 *
2756 * @IEEE80211_HW_SUPPORTS_ONLY_HE_MULTI_BSSID: Hardware supports multi BSSID
2757 * only for HE APs. Applies if @IEEE80211_HW_SUPPORTS_MULTI_BSSID is set.
2758 *
2759 * @IEEE80211_HW_AMPDU_KEYBORDER_SUPPORT: The card and driver is only
2760 * aggregating MPDUs with the same keyid, allowing mac80211 to keep Tx
2761 * A-MPDU sessions active while rekeying with Extended Key ID.
2762 *
2763 * @IEEE80211_HW_SUPPORTS_TX_ENCAP_OFFLOAD: Hardware supports tx encapsulation
2764 * offload
2765 *
2766 * @IEEE80211_HW_SUPPORTS_RX_DECAP_OFFLOAD: Hardware supports rx decapsulation
2767 * offload
2768 *
2769 * @IEEE80211_HW_SUPPORTS_CONC_MON_RX_DECAP: Hardware supports concurrent rx
2770 * decapsulation offload and passing raw 802.11 frames for monitor iface.
2771 * If this is supported, the driver must pass both 802.3 frames for real
2772 * usage and 802.11 frames with %RX_FLAG_ONLY_MONITOR set for monitor to
2773 * the stack.
2774 *
2775 * @IEEE80211_HW_DETECTS_COLOR_COLLISION: HW/driver has support for BSS color
2776 * collision detection and doesn't need it in software.
2777 *
2778 * @IEEE80211_HW_MLO_MCAST_MULTI_LINK_TX: Hardware/driver handles transmitting
2779 * multicast frames on all links, mac80211 should not do that.
2780 *
2781 * @IEEE80211_HW_DISALLOW_PUNCTURING: HW requires disabling puncturing in EHT
2782 * and connecting with a lower bandwidth instead
2783 *
2784 * @IEEE80211_HW_HANDLES_QUIET_CSA: HW/driver handles quieting for CSA, so
2785 * no need to stop queues. This really should be set by a driver that
2786 * implements MLO, so operation can continue on other links when one
2787 * link is switching.
2788 *
2789 * @NUM_IEEE80211_HW_FLAGS: number of hardware flags, used for sizing arrays
2790 */
2791enum ieee80211_hw_flags {
2792 IEEE80211_HW_HAS_RATE_CONTROL,
2793 IEEE80211_HW_RX_INCLUDES_FCS,
2794 IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING,
2795 IEEE80211_HW_SIGNAL_UNSPEC,
2796 IEEE80211_HW_SIGNAL_DBM,
2797 IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC,
2798 IEEE80211_HW_SPECTRUM_MGMT,
2799 IEEE80211_HW_AMPDU_AGGREGATION,
2800 IEEE80211_HW_SUPPORTS_PS,
2801 IEEE80211_HW_PS_NULLFUNC_STACK,
2802 IEEE80211_HW_SUPPORTS_DYNAMIC_PS,
2803 IEEE80211_HW_MFP_CAPABLE,
2804 IEEE80211_HW_WANT_MONITOR_VIF,
2805 IEEE80211_HW_NO_AUTO_VIF,
2806 IEEE80211_HW_SW_CRYPTO_CONTROL,
2807 IEEE80211_HW_SUPPORT_FAST_XMIT,
2808 IEEE80211_HW_REPORTS_TX_ACK_STATUS,
2809 IEEE80211_HW_CONNECTION_MONITOR,
2810 IEEE80211_HW_QUEUE_CONTROL,
2811 IEEE80211_HW_SUPPORTS_PER_STA_GTK,
2812 IEEE80211_HW_AP_LINK_PS,
2813 IEEE80211_HW_TX_AMPDU_SETUP_IN_HW,
2814 IEEE80211_HW_SUPPORTS_RC_TABLE,
2815 IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF,
2816 IEEE80211_HW_TIMING_BEACON_ONLY,
2817 IEEE80211_HW_SUPPORTS_HT_CCK_RATES,
2818 IEEE80211_HW_CHANCTX_STA_CSA,
2819 IEEE80211_HW_SUPPORTS_CLONED_SKBS,
2820 IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS,
2821 IEEE80211_HW_TDLS_WIDER_BW,
2822 IEEE80211_HW_SUPPORTS_AMSDU_IN_AMPDU,
2823 IEEE80211_HW_BEACON_TX_STATUS,
2824 IEEE80211_HW_NEEDS_UNIQUE_STA_ADDR,
2825 IEEE80211_HW_SUPPORTS_REORDERING_BUFFER,
2826 IEEE80211_HW_USES_RSS,
2827 IEEE80211_HW_TX_AMSDU,
2828 IEEE80211_HW_TX_FRAG_LIST,
2829 IEEE80211_HW_REPORTS_LOW_ACK,
2830 IEEE80211_HW_SUPPORTS_TX_FRAG,
2831 IEEE80211_HW_SUPPORTS_TDLS_BUFFER_STA,
2832 IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP,
2833 IEEE80211_HW_DOESNT_SUPPORT_QOS_NDP,
2834 IEEE80211_HW_BUFF_MMPDU_TXQ,
2835 IEEE80211_HW_SUPPORTS_VHT_EXT_NSS_BW,
2836 IEEE80211_HW_STA_MMPDU_TXQ,
2837 IEEE80211_HW_TX_STATUS_NO_AMPDU_LEN,
2838 IEEE80211_HW_SUPPORTS_MULTI_BSSID,
2839 IEEE80211_HW_SUPPORTS_ONLY_HE_MULTI_BSSID,
2840 IEEE80211_HW_AMPDU_KEYBORDER_SUPPORT,
2841 IEEE80211_HW_SUPPORTS_TX_ENCAP_OFFLOAD,
2842 IEEE80211_HW_SUPPORTS_RX_DECAP_OFFLOAD,
2843 IEEE80211_HW_SUPPORTS_CONC_MON_RX_DECAP,
2844 IEEE80211_HW_DETECTS_COLOR_COLLISION,
2845 IEEE80211_HW_MLO_MCAST_MULTI_LINK_TX,
2846 IEEE80211_HW_DISALLOW_PUNCTURING,
2847 IEEE80211_HW_HANDLES_QUIET_CSA,
2848
2849 /* keep last, obviously */
2850 NUM_IEEE80211_HW_FLAGS
2851};
2852
2853/**
2854 * struct ieee80211_hw - hardware information and state
2855 *
2856 * This structure contains the configuration and hardware
2857 * information for an 802.11 PHY.
2858 *
2859 * @wiphy: This points to the &struct wiphy allocated for this
2860 * 802.11 PHY. You must fill in the @perm_addr and @dev
2861 * members of this structure using SET_IEEE80211_DEV()
2862 * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
2863 * bands (with channels, bitrates) are registered here.
2864 *
2865 * @conf: &struct ieee80211_conf, device configuration, don't use.
2866 *
2867 * @priv: pointer to private area that was allocated for driver use
2868 * along with this structure.
2869 *
2870 * @flags: hardware flags, see &enum ieee80211_hw_flags.
2871 *
2872 * @extra_tx_headroom: headroom to reserve in each transmit skb
2873 * for use by the driver (e.g. for transmit headers.)
2874 *
2875 * @extra_beacon_tailroom: tailroom to reserve in each beacon tx skb.
2876 * Can be used by drivers to add extra IEs.
2877 *
2878 * @max_signal: Maximum value for signal (rssi) in RX information, used
2879 * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
2880 *
2881 * @max_listen_interval: max listen interval in units of beacon interval
2882 * that HW supports
2883 *
2884 * @queues: number of available hardware transmit queues for
2885 * data packets. WMM/QoS requires at least four, these
2886 * queues need to have configurable access parameters.
2887 *
2888 * @rate_control_algorithm: rate control algorithm for this hardware.
2889 * If unset (NULL), the default algorithm will be used. Must be
2890 * set before calling ieee80211_register_hw().
2891 *
2892 * @vif_data_size: size (in bytes) of the drv_priv data area
2893 * within &struct ieee80211_vif.
2894 * @sta_data_size: size (in bytes) of the drv_priv data area
2895 * within &struct ieee80211_sta.
2896 * @chanctx_data_size: size (in bytes) of the drv_priv data area
2897 * within &struct ieee80211_chanctx_conf.
2898 * @txq_data_size: size (in bytes) of the drv_priv data area
2899 * within @struct ieee80211_txq.
2900 *
2901 * @max_rates: maximum number of alternate rate retry stages the hw
2902 * can handle.
2903 * @max_report_rates: maximum number of alternate rate retry stages
2904 * the hw can report back.
2905 * @max_rate_tries: maximum number of tries for each stage
2906 *
2907 * @max_rx_aggregation_subframes: maximum buffer size (number of
2908 * sub-frames) to be used for A-MPDU block ack receiver
2909 * aggregation.
2910 * This is only relevant if the device has restrictions on the
2911 * number of subframes, if it relies on mac80211 to do reordering
2912 * it shouldn't be set.
2913 *
2914 * @max_tx_aggregation_subframes: maximum number of subframes in an
2915 * aggregate an HT/HE device will transmit. In HT AddBA we'll
2916 * advertise a constant value of 64 as some older APs crash if
2917 * the window size is smaller (an example is LinkSys WRT120N
2918 * with FW v1.0.07 build 002 Jun 18 2012).
2919 * For AddBA to HE capable peers this value will be used.
2920 *
2921 * @max_tx_fragments: maximum number of tx buffers per (A)-MSDU, sum
2922 * of 1 + skb_shinfo(skb)->nr_frags for each skb in the frag_list.
2923 *
2924 * @offchannel_tx_hw_queue: HW queue ID to use for offchannel TX
2925 * (if %IEEE80211_HW_QUEUE_CONTROL is set)
2926 *
2927 * @radiotap_mcs_details: lists which MCS information can the HW
2928 * reports, by default it is set to _MCS, _GI and _BW but doesn't
2929 * include _FMT. Use %IEEE80211_RADIOTAP_MCS_HAVE_\* values, only
2930 * adding _BW is supported today.
2931 *
2932 * @radiotap_vht_details: lists which VHT MCS information the HW reports,
2933 * the default is _GI | _BANDWIDTH.
2934 * Use the %IEEE80211_RADIOTAP_VHT_KNOWN_\* values.
2935 *
2936 * @radiotap_timestamp: Information for the radiotap timestamp field; if the
2937 * @units_pos member is set to a non-negative value then the timestamp
2938 * field will be added and populated from the &struct ieee80211_rx_status
2939 * device_timestamp.
2940 * @radiotap_timestamp.units_pos: Must be set to a combination of a
2941 * IEEE80211_RADIOTAP_TIMESTAMP_UNIT_* and a
2942 * IEEE80211_RADIOTAP_TIMESTAMP_SPOS_* value.
2943 * @radiotap_timestamp.accuracy: If non-negative, fills the accuracy in the
2944 * radiotap field and the accuracy known flag will be set.
2945 *
2946 * @netdev_features: netdev features to be set in each netdev created
2947 * from this HW. Note that not all features are usable with mac80211,
2948 * other features will be rejected during HW registration.
2949 *
2950 * @uapsd_queues: This bitmap is included in (re)association frame to indicate
2951 * for each access category if it is uAPSD trigger-enabled and delivery-
2952 * enabled. Use IEEE80211_WMM_IE_STA_QOSINFO_AC_* to set this bitmap.
2953 * Each bit corresponds to different AC. Value '1' in specific bit means
2954 * that corresponding AC is both trigger- and delivery-enabled. '0' means
2955 * neither enabled.
2956 *
2957 * @uapsd_max_sp_len: maximum number of total buffered frames the WMM AP may
2958 * deliver to a WMM STA during any Service Period triggered by the WMM STA.
2959 * Use IEEE80211_WMM_IE_STA_QOSINFO_SP_* for correct values.
2960 *
2961 * @max_nan_de_entries: maximum number of NAN DE functions supported by the
2962 * device.
2963 *
2964 * @tx_sk_pacing_shift: Pacing shift to set on TCP sockets when frames from
2965 * them are encountered. The default should typically not be changed,
2966 * unless the driver has good reasons for needing more buffers.
2967 *
2968 * @weight_multiplier: Driver specific airtime weight multiplier used while
2969 * refilling deficit of each TXQ.
2970 *
2971 * @max_mtu: the max mtu could be set.
2972 *
2973 * @tx_power_levels: a list of power levels supported by the wifi hardware.
2974 * The power levels can be specified either as integer or fractions.
2975 * The power level at idx 0 shall be the maximum positive power level.
2976 *
2977 * @max_txpwr_levels_idx: the maximum valid idx of 'tx_power_levels' list.
2978 */
2979struct ieee80211_hw {
2980 struct ieee80211_conf conf;
2981 struct wiphy *wiphy;
2982 const char *rate_control_algorithm;
2983 void *priv;
2984 unsigned long flags[BITS_TO_LONGS(NUM_IEEE80211_HW_FLAGS)];
2985 unsigned int extra_tx_headroom;
2986 unsigned int extra_beacon_tailroom;
2987 int vif_data_size;
2988 int sta_data_size;
2989 int chanctx_data_size;
2990 int txq_data_size;
2991 u16 queues;
2992 u16 max_listen_interval;
2993 s8 max_signal;
2994 u8 max_rates;
2995 u8 max_report_rates;
2996 u8 max_rate_tries;
2997 u16 max_rx_aggregation_subframes;
2998 u16 max_tx_aggregation_subframes;
2999 u8 max_tx_fragments;
3000 u8 offchannel_tx_hw_queue;
3001 u8 radiotap_mcs_details;
3002 u16 radiotap_vht_details;
3003 struct {
3004 int units_pos;
3005 s16 accuracy;
3006 } radiotap_timestamp;
3007 netdev_features_t netdev_features;
3008 u8 uapsd_queues;
3009 u8 uapsd_max_sp_len;
3010 u8 max_nan_de_entries;
3011 u8 tx_sk_pacing_shift;
3012 u8 weight_multiplier;
3013 u32 max_mtu;
3014 const s8 *tx_power_levels;
3015 u8 max_txpwr_levels_idx;
3016};
3017
3018static inline bool _ieee80211_hw_check(struct ieee80211_hw *hw,
3019 enum ieee80211_hw_flags flg)
3020{
3021 return test_bit(flg, hw->flags);
3022}
3023#define ieee80211_hw_check(hw, flg) _ieee80211_hw_check(hw, IEEE80211_HW_##flg)
3024
3025static inline void _ieee80211_hw_set(struct ieee80211_hw *hw,
3026 enum ieee80211_hw_flags flg)
3027{
3028 return __set_bit(flg, hw->flags);
3029}
3030#define ieee80211_hw_set(hw, flg) _ieee80211_hw_set(hw, IEEE80211_HW_##flg)
3031
3032/**
3033 * struct ieee80211_scan_request - hw scan request
3034 *
3035 * @ies: pointers different parts of IEs (in req.ie)
3036 * @req: cfg80211 request.
3037 */
3038struct ieee80211_scan_request {
3039 struct ieee80211_scan_ies ies;
3040
3041 /* Keep last */
3042 struct cfg80211_scan_request req;
3043};
3044
3045/**
3046 * struct ieee80211_tdls_ch_sw_params - TDLS channel switch parameters
3047 *
3048 * @sta: peer this TDLS channel-switch request/response came from
3049 * @chandef: channel referenced in a TDLS channel-switch request
3050 * @action_code: see &enum ieee80211_tdls_actioncode
3051 * @status: channel-switch response status
3052 * @timestamp: time at which the frame was received
3053 * @switch_time: switch-timing parameter received in the frame
3054 * @switch_timeout: switch-timing parameter received in the frame
3055 * @tmpl_skb: TDLS switch-channel response template
3056 * @ch_sw_tm_ie: offset of the channel-switch timing IE inside @tmpl_skb
3057 */
3058struct ieee80211_tdls_ch_sw_params {
3059 struct ieee80211_sta *sta;
3060 struct cfg80211_chan_def *chandef;
3061 u8 action_code;
3062 u32 status;
3063 u32 timestamp;
3064 u16 switch_time;
3065 u16 switch_timeout;
3066 struct sk_buff *tmpl_skb;
3067 u32 ch_sw_tm_ie;
3068};
3069
3070/**
3071 * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy
3072 *
3073 * @wiphy: the &struct wiphy which we want to query
3074 *
3075 * mac80211 drivers can use this to get to their respective
3076 * &struct ieee80211_hw. Drivers wishing to get to their own private
3077 * structure can then access it via hw->priv. Note that mac802111 drivers should
3078 * not use wiphy_priv() to try to get their private driver structure as this
3079 * is already used internally by mac80211.
3080 *
3081 * Return: The mac80211 driver hw struct of @wiphy.
3082 */
3083struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy);
3084
3085/**
3086 * SET_IEEE80211_DEV - set device for 802.11 hardware
3087 *
3088 * @hw: the &struct ieee80211_hw to set the device for
3089 * @dev: the &struct device of this 802.11 device
3090 */
3091static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev)
3092{
3093 set_wiphy_dev(hw->wiphy, dev);
3094}
3095
3096/**
3097 * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware
3098 *
3099 * @hw: the &struct ieee80211_hw to set the MAC address for
3100 * @addr: the address to set
3101 */
3102static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, const u8 *addr)
3103{
3104 memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
3105}
3106
3107static inline struct ieee80211_rate *
3108ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
3109 const struct ieee80211_tx_info *c)
3110{
3111 if (WARN_ON_ONCE(c->control.rates[0].idx < 0))
3112 return NULL;
3113 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx];
3114}
3115
3116static inline struct ieee80211_rate *
3117ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw,
3118 const struct ieee80211_tx_info *c)
3119{
3120 if (c->control.rts_cts_rate_idx < 0)
3121 return NULL;
3122 return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx];
3123}
3124
3125static inline struct ieee80211_rate *
3126ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
3127 const struct ieee80211_tx_info *c, int idx)
3128{
3129 if (c->control.rates[idx + 1].idx < 0)
3130 return NULL;
3131 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx];
3132}
3133
3134/**
3135 * ieee80211_free_txskb - free TX skb
3136 * @hw: the hardware
3137 * @skb: the skb
3138 *
3139 * Free a transmit skb. Use this function when some failure
3140 * to transmit happened and thus status cannot be reported.
3141 */
3142void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb);
3143
3144/**
3145 * DOC: Hardware crypto acceleration
3146 *
3147 * mac80211 is capable of taking advantage of many hardware
3148 * acceleration designs for encryption and decryption operations.
3149 *
3150 * The set_key() callback in the &struct ieee80211_ops for a given
3151 * device is called to enable hardware acceleration of encryption and
3152 * decryption. The callback takes a @sta parameter that will be NULL
3153 * for default keys or keys used for transmission only, or point to
3154 * the station information for the peer for individual keys.
3155 * Multiple transmission keys with the same key index may be used when
3156 * VLANs are configured for an access point.
3157 *
3158 * When transmitting, the TX control data will use the @hw_key_idx
3159 * selected by the driver by modifying the &struct ieee80211_key_conf
3160 * pointed to by the @key parameter to the set_key() function.
3161 *
3162 * The set_key() call for the %SET_KEY command should return 0 if
3163 * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be
3164 * added; if you return 0 then hw_key_idx must be assigned to the
3165 * hardware key index. You are free to use the full u8 range.
3166 *
3167 * Note that in the case that the @IEEE80211_HW_SW_CRYPTO_CONTROL flag is
3168 * set, mac80211 will not automatically fall back to software crypto if
3169 * enabling hardware crypto failed. The set_key() call may also return the
3170 * value 1 to permit this specific key/algorithm to be done in software.
3171 *
3172 * When the cmd is %DISABLE_KEY then it must succeed.
3173 *
3174 * Note that it is permissible to not decrypt a frame even if a key
3175 * for it has been uploaded to hardware. The stack will not make any
3176 * decision based on whether a key has been uploaded or not but rather
3177 * based on the receive flags.
3178 *
3179 * The &struct ieee80211_key_conf structure pointed to by the @key
3180 * parameter is guaranteed to be valid until another call to set_key()
3181 * removes it, but it can only be used as a cookie to differentiate
3182 * keys.
3183 *
3184 * In TKIP some HW need to be provided a phase 1 key, for RX decryption
3185 * acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key
3186 * handler.
3187 * The update_tkip_key() call updates the driver with the new phase 1 key.
3188 * This happens every time the iv16 wraps around (every 65536 packets). The
3189 * set_key() call will happen only once for each key (unless the AP did
3190 * rekeying); it will not include a valid phase 1 key. The valid phase 1 key is
3191 * provided by update_tkip_key only. The trigger that makes mac80211 call this
3192 * handler is software decryption with wrap around of iv16.
3193 *
3194 * The set_default_unicast_key() call updates the default WEP key index
3195 * configured to the hardware for WEP encryption type. This is required
3196 * for devices that support offload of data packets (e.g. ARP responses).
3197 *
3198 * Mac80211 drivers should set the @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 flag
3199 * when they are able to replace in-use PTK keys according to the following
3200 * requirements:
3201 * 1) They do not hand over frames decrypted with the old key to mac80211
3202 once the call to set_key() with command %DISABLE_KEY has been completed,
3203 2) either drop or continue to use the old key for any outgoing frames queued
3204 at the time of the key deletion (including re-transmits),
3205 3) never send out a frame queued prior to the set_key() %SET_KEY command
3206 encrypted with the new key when also needing
3207 @IEEE80211_KEY_FLAG_GENERATE_IV and
3208 4) never send out a frame unencrypted when it should be encrypted.
3209 Mac80211 will not queue any new frames for a deleted key to the driver.
3210 */
3211
3212/**
3213 * DOC: Powersave support
3214 *
3215 * mac80211 has support for various powersave implementations.
3216 *
3217 * First, it can support hardware that handles all powersaving by itself;
3218 * such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS hardware
3219 * flag. In that case, it will be told about the desired powersave mode
3220 * with the %IEEE80211_CONF_PS flag depending on the association status.
3221 * The hardware must take care of sending nullfunc frames when necessary,
3222 * i.e. when entering and leaving powersave mode. The hardware is required
3223 * to look at the AID in beacons and signal to the AP that it woke up when
3224 * it finds traffic directed to it.
3225 *
3226 * %IEEE80211_CONF_PS flag enabled means that the powersave mode defined in
3227 * IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused
3228 * with hardware wakeup and sleep states. Driver is responsible for waking
3229 * up the hardware before issuing commands to the hardware and putting it
3230 * back to sleep at appropriate times.
3231 *
3232 * When PS is enabled, hardware needs to wakeup for beacons and receive the
3233 * buffered multicast/broadcast frames after the beacon. Also it must be
3234 * possible to send frames and receive the acknowledment frame.
3235 *
3236 * Other hardware designs cannot send nullfunc frames by themselves and also
3237 * need software support for parsing the TIM bitmap. This is also supported
3238 * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and
3239 * %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still
3240 * required to pass up beacons. The hardware is still required to handle
3241 * waking up for multicast traffic; if it cannot the driver must handle that
3242 * as best as it can; mac80211 is too slow to do that.
3243 *
3244 * Dynamic powersave is an extension to normal powersave in which the
3245 * hardware stays awake for a user-specified period of time after sending a
3246 * frame so that reply frames need not be buffered and therefore delayed to
3247 * the next wakeup. It's a compromise of getting good enough latency when
3248 * there's data traffic and still saving significantly power in idle
3249 * periods.
3250 *
3251 * Dynamic powersave is simply supported by mac80211 enabling and disabling
3252 * PS based on traffic. Driver needs to only set %IEEE80211_HW_SUPPORTS_PS
3253 * flag and mac80211 will handle everything automatically. Additionally,
3254 * hardware having support for the dynamic PS feature may set the
3255 * %IEEE80211_HW_SUPPORTS_DYNAMIC_PS flag to indicate that it can support
3256 * dynamic PS mode itself. The driver needs to look at the
3257 * @dynamic_ps_timeout hardware configuration value and use it that value
3258 * whenever %IEEE80211_CONF_PS is set. In this case mac80211 will disable
3259 * dynamic PS feature in stack and will just keep %IEEE80211_CONF_PS
3260 * enabled whenever user has enabled powersave.
3261 *
3262 * Driver informs U-APSD client support by enabling
3263 * %IEEE80211_VIF_SUPPORTS_UAPSD flag. The mode is configured through the
3264 * uapsd parameter in conf_tx() operation. Hardware needs to send the QoS
3265 * Nullfunc frames and stay awake until the service period has ended. To
3266 * utilize U-APSD, dynamic powersave is disabled for voip AC and all frames
3267 * from that AC are transmitted with powersave enabled.
3268 *
3269 * Note: U-APSD client mode is not yet supported with
3270 * %IEEE80211_HW_PS_NULLFUNC_STACK.
3271 */
3272
3273/**
3274 * DOC: Beacon filter support
3275 *
3276 * Some hardware have beacon filter support to reduce host cpu wakeups
3277 * which will reduce system power consumption. It usually works so that
3278 * the firmware creates a checksum of the beacon but omits all constantly
3279 * changing elements (TSF, TIM etc). Whenever the checksum changes the
3280 * beacon is forwarded to the host, otherwise it will be just dropped. That
3281 * way the host will only receive beacons where some relevant information
3282 * (for example ERP protection or WMM settings) have changed.
3283 *
3284 * Beacon filter support is advertised with the %IEEE80211_VIF_BEACON_FILTER
3285 * interface capability. The driver needs to enable beacon filter support
3286 * whenever power save is enabled, that is %IEEE80211_CONF_PS is set. When
3287 * power save is enabled, the stack will not check for beacon loss and the
3288 * driver needs to notify about loss of beacons with ieee80211_beacon_loss().
3289 *
3290 * The time (or number of beacons missed) until the firmware notifies the
3291 * driver of a beacon loss event (which in turn causes the driver to call
3292 * ieee80211_beacon_loss()) should be configurable and will be controlled
3293 * by mac80211 and the roaming algorithm in the future.
3294 *
3295 * Since there may be constantly changing information elements that nothing
3296 * in the software stack cares about, we will, in the future, have mac80211
3297 * tell the driver which information elements are interesting in the sense
3298 * that we want to see changes in them. This will include
3299 *
3300 * - a list of information element IDs
3301 * - a list of OUIs for the vendor information element
3302 *
3303 * Ideally, the hardware would filter out any beacons without changes in the
3304 * requested elements, but if it cannot support that it may, at the expense
3305 * of some efficiency, filter out only a subset. For example, if the device
3306 * doesn't support checking for OUIs it should pass up all changes in all
3307 * vendor information elements.
3308 *
3309 * Note that change, for the sake of simplification, also includes information
3310 * elements appearing or disappearing from the beacon.
3311 *
3312 * Some hardware supports an "ignore list" instead. Just make sure nothing
3313 * that was requested is on the ignore list, and include commonly changing
3314 * information element IDs in the ignore list, for example 11 (BSS load) and
3315 * the various vendor-assigned IEs with unknown contents (128, 129, 133-136,
3316 * 149, 150, 155, 156, 173, 176, 178, 179, 219); for forward compatibility
3317 * it could also include some currently unused IDs.
3318 *
3319 *
3320 * In addition to these capabilities, hardware should support notifying the
3321 * host of changes in the beacon RSSI. This is relevant to implement roaming
3322 * when no traffic is flowing (when traffic is flowing we see the RSSI of
3323 * the received data packets). This can consist of notifying the host when
3324 * the RSSI changes significantly or when it drops below or rises above
3325 * configurable thresholds. In the future these thresholds will also be
3326 * configured by mac80211 (which gets them from userspace) to implement
3327 * them as the roaming algorithm requires.
3328 *
3329 * If the hardware cannot implement this, the driver should ask it to
3330 * periodically pass beacon frames to the host so that software can do the
3331 * signal strength threshold checking.
3332 */
3333
3334/**
3335 * DOC: Spatial multiplexing power save
3336 *
3337 * SMPS (Spatial multiplexing power save) is a mechanism to conserve
3338 * power in an 802.11n implementation. For details on the mechanism
3339 * and rationale, please refer to 802.11 (as amended by 802.11n-2009)
3340 * "11.2.3 SM power save".
3341 *
3342 * The mac80211 implementation is capable of sending action frames
3343 * to update the AP about the station's SMPS mode, and will instruct
3344 * the driver to enter the specific mode. It will also announce the
3345 * requested SMPS mode during the association handshake. Hardware
3346 * support for this feature is required, and can be indicated by
3347 * hardware flags.
3348 *
3349 * The default mode will be "automatic", which nl80211/cfg80211
3350 * defines to be dynamic SMPS in (regular) powersave, and SMPS
3351 * turned off otherwise.
3352 *
3353 * To support this feature, the driver must set the appropriate
3354 * hardware support flags, and handle the SMPS flag to the config()
3355 * operation. It will then with this mechanism be instructed to
3356 * enter the requested SMPS mode while associated to an HT AP.
3357 */
3358
3359/**
3360 * DOC: Frame filtering
3361 *
3362 * mac80211 requires to see many management frames for proper
3363 * operation, and users may want to see many more frames when
3364 * in monitor mode. However, for best CPU usage and power consumption,
3365 * having as few frames as possible percolate through the stack is
3366 * desirable. Hence, the hardware should filter as much as possible.
3367 *
3368 * To achieve this, mac80211 uses filter flags (see below) to tell
3369 * the driver's configure_filter() function which frames should be
3370 * passed to mac80211 and which should be filtered out.
3371 *
3372 * Before configure_filter() is invoked, the prepare_multicast()
3373 * callback is invoked with the parameters @mc_count and @mc_list
3374 * for the combined multicast address list of all virtual interfaces.
3375 * It's use is optional, and it returns a u64 that is passed to
3376 * configure_filter(). Additionally, configure_filter() has the
3377 * arguments @changed_flags telling which flags were changed and
3378 * @total_flags with the new flag states.
3379 *
3380 * If your device has no multicast address filters your driver will
3381 * need to check both the %FIF_ALLMULTI flag and the @mc_count
3382 * parameter to see whether multicast frames should be accepted
3383 * or dropped.
3384 *
3385 * All unsupported flags in @total_flags must be cleared.
3386 * Hardware does not support a flag if it is incapable of _passing_
3387 * the frame to the stack. Otherwise the driver must ignore
3388 * the flag, but not clear it.
3389 * You must _only_ clear the flag (announce no support for the
3390 * flag to mac80211) if you are not able to pass the packet type
3391 * to the stack (so the hardware always filters it).
3392 * So for example, you should clear @FIF_CONTROL, if your hardware
3393 * always filters control frames. If your hardware always passes
3394 * control frames to the kernel and is incapable of filtering them,
3395 * you do _not_ clear the @FIF_CONTROL flag.
3396 * This rule applies to all other FIF flags as well.
3397 */
3398
3399/**
3400 * DOC: AP support for powersaving clients
3401 *
3402 * In order to implement AP and P2P GO modes, mac80211 has support for
3403 * client powersaving, both "legacy" PS (PS-Poll/null data) and uAPSD.
3404 * There currently is no support for sAPSD.
3405 *
3406 * There is one assumption that mac80211 makes, namely that a client
3407 * will not poll with PS-Poll and trigger with uAPSD at the same time.
3408 * Both are supported, and both can be used by the same client, but
3409 * they can't be used concurrently by the same client. This simplifies
3410 * the driver code.
3411 *
3412 * The first thing to keep in mind is that there is a flag for complete
3413 * driver implementation: %IEEE80211_HW_AP_LINK_PS. If this flag is set,
3414 * mac80211 expects the driver to handle most of the state machine for
3415 * powersaving clients and will ignore the PM bit in incoming frames.
3416 * Drivers then use ieee80211_sta_ps_transition() to inform mac80211 of
3417 * stations' powersave transitions. In this mode, mac80211 also doesn't
3418 * handle PS-Poll/uAPSD.
3419 *
3420 * In the mode without %IEEE80211_HW_AP_LINK_PS, mac80211 will check the
3421 * PM bit in incoming frames for client powersave transitions. When a
3422 * station goes to sleep, we will stop transmitting to it. There is,
3423 * however, a race condition: a station might go to sleep while there is
3424 * data buffered on hardware queues. If the device has support for this
3425 * it will reject frames, and the driver should give the frames back to
3426 * mac80211 with the %IEEE80211_TX_STAT_TX_FILTERED flag set which will
3427 * cause mac80211 to retry the frame when the station wakes up. The
3428 * driver is also notified of powersave transitions by calling its
3429 * @sta_notify callback.
3430 *
3431 * When the station is asleep, it has three choices: it can wake up,
3432 * it can PS-Poll, or it can possibly start a uAPSD service period.
3433 * Waking up is implemented by simply transmitting all buffered (and
3434 * filtered) frames to the station. This is the easiest case. When
3435 * the station sends a PS-Poll or a uAPSD trigger frame, mac80211
3436 * will inform the driver of this with the @allow_buffered_frames
3437 * callback; this callback is optional. mac80211 will then transmit
3438 * the frames as usual and set the %IEEE80211_TX_CTL_NO_PS_BUFFER
3439 * on each frame. The last frame in the service period (or the only
3440 * response to a PS-Poll) also has %IEEE80211_TX_STATUS_EOSP set to
3441 * indicate that it ends the service period; as this frame must have
3442 * TX status report it also sets %IEEE80211_TX_CTL_REQ_TX_STATUS.
3443 * When TX status is reported for this frame, the service period is
3444 * marked has having ended and a new one can be started by the peer.
3445 *
3446 * Additionally, non-bufferable MMPDUs can also be transmitted by
3447 * mac80211 with the %IEEE80211_TX_CTL_NO_PS_BUFFER set in them.
3448 *
3449 * Another race condition can happen on some devices like iwlwifi
3450 * when there are frames queued for the station and it wakes up
3451 * or polls; the frames that are already queued could end up being
3452 * transmitted first instead, causing reordering and/or wrong
3453 * processing of the EOSP. The cause is that allowing frames to be
3454 * transmitted to a certain station is out-of-band communication to
3455 * the device. To allow this problem to be solved, the driver can
3456 * call ieee80211_sta_block_awake() if frames are buffered when it
3457 * is notified that the station went to sleep. When all these frames
3458 * have been filtered (see above), it must call the function again
3459 * to indicate that the station is no longer blocked.
3460 *
3461 * If the driver buffers frames in the driver for aggregation in any
3462 * way, it must use the ieee80211_sta_set_buffered() call when it is
3463 * notified of the station going to sleep to inform mac80211 of any
3464 * TIDs that have frames buffered. Note that when a station wakes up
3465 * this information is reset (hence the requirement to call it when
3466 * informed of the station going to sleep). Then, when a service
3467 * period starts for any reason, @release_buffered_frames is called
3468 * with the number of frames to be released and which TIDs they are
3469 * to come from. In this case, the driver is responsible for setting
3470 * the EOSP (for uAPSD) and MORE_DATA bits in the released frames.
3471 * To help the @more_data parameter is passed to tell the driver if
3472 * there is more data on other TIDs -- the TIDs to release frames
3473 * from are ignored since mac80211 doesn't know how many frames the
3474 * buffers for those TIDs contain.
3475 *
3476 * If the driver also implement GO mode, where absence periods may
3477 * shorten service periods (or abort PS-Poll responses), it must
3478 * filter those response frames except in the case of frames that
3479 * are buffered in the driver -- those must remain buffered to avoid
3480 * reordering. Because it is possible that no frames are released
3481 * in this case, the driver must call ieee80211_sta_eosp()
3482 * to indicate to mac80211 that the service period ended anyway.
3483 *
3484 * Finally, if frames from multiple TIDs are released from mac80211
3485 * but the driver might reorder them, it must clear & set the flags
3486 * appropriately (only the last frame may have %IEEE80211_TX_STATUS_EOSP)
3487 * and also take care of the EOSP and MORE_DATA bits in the frame.
3488 * The driver may also use ieee80211_sta_eosp() in this case.
3489 *
3490 * Note that if the driver ever buffers frames other than QoS-data
3491 * frames, it must take care to never send a non-QoS-data frame as
3492 * the last frame in a service period, adding a QoS-nulldata frame
3493 * after a non-QoS-data frame if needed.
3494 */
3495
3496/**
3497 * DOC: HW queue control
3498 *
3499 * Before HW queue control was introduced, mac80211 only had a single static
3500 * assignment of per-interface AC software queues to hardware queues. This
3501 * was problematic for a few reasons:
3502 * 1) off-channel transmissions might get stuck behind other frames
3503 * 2) multiple virtual interfaces couldn't be handled correctly
3504 * 3) after-DTIM frames could get stuck behind other frames
3505 *
3506 * To solve this, hardware typically uses multiple different queues for all
3507 * the different usages, and this needs to be propagated into mac80211 so it
3508 * won't have the same problem with the software queues.
3509 *
3510 * Therefore, mac80211 now offers the %IEEE80211_HW_QUEUE_CONTROL capability
3511 * flag that tells it that the driver implements its own queue control. To do
3512 * so, the driver will set up the various queues in each &struct ieee80211_vif
3513 * and the offchannel queue in &struct ieee80211_hw. In response, mac80211 will
3514 * use those queue IDs in the hw_queue field of &struct ieee80211_tx_info and
3515 * if necessary will queue the frame on the right software queue that mirrors
3516 * the hardware queue.
3517 * Additionally, the driver has to then use these HW queue IDs for the queue
3518 * management functions (ieee80211_stop_queue() et al.)
3519 *
3520 * The driver is free to set up the queue mappings as needed; multiple virtual
3521 * interfaces may map to the same hardware queues if needed. The setup has to
3522 * happen during add_interface or change_interface callbacks. For example, a
3523 * driver supporting station+station and station+AP modes might decide to have
3524 * 10 hardware queues to handle different scenarios:
3525 *
3526 * 4 AC HW queues for 1st vif: 0, 1, 2, 3
3527 * 4 AC HW queues for 2nd vif: 4, 5, 6, 7
3528 * after-DTIM queue for AP: 8
3529 * off-channel queue: 9
3530 *
3531 * It would then set up the hardware like this:
3532 * hw.offchannel_tx_hw_queue = 9
3533 *
3534 * and the first virtual interface that is added as follows:
3535 * vif.hw_queue[IEEE80211_AC_VO] = 0
3536 * vif.hw_queue[IEEE80211_AC_VI] = 1
3537 * vif.hw_queue[IEEE80211_AC_BE] = 2
3538 * vif.hw_queue[IEEE80211_AC_BK] = 3
3539 * vif.cab_queue = 8 // if AP mode, otherwise %IEEE80211_INVAL_HW_QUEUE
3540 * and the second virtual interface with 4-7.
3541 *
3542 * If queue 6 gets full, for example, mac80211 would only stop the second
3543 * virtual interface's BE queue since virtual interface queues are per AC.
3544 *
3545 * Note that the vif.cab_queue value should be set to %IEEE80211_INVAL_HW_QUEUE
3546 * whenever the queue is not used (i.e. the interface is not in AP mode) if the
3547 * queue could potentially be shared since mac80211 will look at cab_queue when
3548 * a queue is stopped/woken even if the interface is not in AP mode.
3549 */
3550
3551/**
3552 * enum ieee80211_filter_flags - hardware filter flags
3553 *
3554 * These flags determine what the filter in hardware should be
3555 * programmed to let through and what should not be passed to the
3556 * stack. It is always safe to pass more frames than requested,
3557 * but this has negative impact on power consumption.
3558 *
3559 * @FIF_ALLMULTI: pass all multicast frames, this is used if requested
3560 * by the user or if the hardware is not capable of filtering by
3561 * multicast address.
3562 *
3563 * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the
3564 * %RX_FLAG_FAILED_FCS_CRC for them)
3565 *
3566 * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set
3567 * the %RX_FLAG_FAILED_PLCP_CRC for them
3568 *
3569 * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate
3570 * to the hardware that it should not filter beacons or probe responses
3571 * by BSSID. Filtering them can greatly reduce the amount of processing
3572 * mac80211 needs to do and the amount of CPU wakeups, so you should
3573 * honour this flag if possible.
3574 *
3575 * @FIF_CONTROL: pass control frames (except for PS Poll) addressed to this
3576 * station
3577 *
3578 * @FIF_OTHER_BSS: pass frames destined to other BSSes
3579 *
3580 * @FIF_PSPOLL: pass PS Poll frames
3581 *
3582 * @FIF_PROBE_REQ: pass probe request frames
3583 *
3584 * @FIF_MCAST_ACTION: pass multicast Action frames
3585 */
3586enum ieee80211_filter_flags {
3587 FIF_ALLMULTI = 1<<1,
3588 FIF_FCSFAIL = 1<<2,
3589 FIF_PLCPFAIL = 1<<3,
3590 FIF_BCN_PRBRESP_PROMISC = 1<<4,
3591 FIF_CONTROL = 1<<5,
3592 FIF_OTHER_BSS = 1<<6,
3593 FIF_PSPOLL = 1<<7,
3594 FIF_PROBE_REQ = 1<<8,
3595 FIF_MCAST_ACTION = 1<<9,
3596};
3597
3598/**
3599 * enum ieee80211_ampdu_mlme_action - A-MPDU actions
3600 *
3601 * These flags are used with the ampdu_action() callback in
3602 * &struct ieee80211_ops to indicate which action is needed.
3603 *
3604 * Note that drivers MUST be able to deal with a TX aggregation
3605 * session being stopped even before they OK'ed starting it by
3606 * calling ieee80211_start_tx_ba_cb_irqsafe, because the peer
3607 * might receive the addBA frame and send a delBA right away!
3608 *
3609 * @IEEE80211_AMPDU_RX_START: start RX aggregation
3610 * @IEEE80211_AMPDU_RX_STOP: stop RX aggregation
3611 * @IEEE80211_AMPDU_TX_START: start TX aggregation, the driver must either
3612 * call ieee80211_start_tx_ba_cb_irqsafe() or
3613 * call ieee80211_start_tx_ba_cb_irqsafe() with status
3614 * %IEEE80211_AMPDU_TX_START_DELAY_ADDBA to delay addba after
3615 * ieee80211_start_tx_ba_cb_irqsafe is called, or just return the special
3616 * status %IEEE80211_AMPDU_TX_START_IMMEDIATE.
3617 * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational
3618 * @IEEE80211_AMPDU_TX_STOP_CONT: stop TX aggregation but continue transmitting
3619 * queued packets, now unaggregated. After all packets are transmitted the
3620 * driver has to call ieee80211_stop_tx_ba_cb_irqsafe().
3621 * @IEEE80211_AMPDU_TX_STOP_FLUSH: stop TX aggregation and flush all packets,
3622 * called when the station is removed. There's no need or reason to call
3623 * ieee80211_stop_tx_ba_cb_irqsafe() in this case as mac80211 assumes the
3624 * session is gone and removes the station.
3625 * @IEEE80211_AMPDU_TX_STOP_FLUSH_CONT: called when TX aggregation is stopped
3626 * but the driver hasn't called ieee80211_stop_tx_ba_cb_irqsafe() yet and
3627 * now the connection is dropped and the station will be removed. Drivers
3628 * should clean up and drop remaining packets when this is called.
3629 */
3630enum ieee80211_ampdu_mlme_action {
3631 IEEE80211_AMPDU_RX_START,
3632 IEEE80211_AMPDU_RX_STOP,
3633 IEEE80211_AMPDU_TX_START,
3634 IEEE80211_AMPDU_TX_STOP_CONT,
3635 IEEE80211_AMPDU_TX_STOP_FLUSH,
3636 IEEE80211_AMPDU_TX_STOP_FLUSH_CONT,
3637 IEEE80211_AMPDU_TX_OPERATIONAL,
3638};
3639
3640#define IEEE80211_AMPDU_TX_START_IMMEDIATE 1
3641#define IEEE80211_AMPDU_TX_START_DELAY_ADDBA 2
3642
3643/**
3644 * struct ieee80211_ampdu_params - AMPDU action parameters
3645 *
3646 * @action: the ampdu action, value from %ieee80211_ampdu_mlme_action.
3647 * @sta: peer of this AMPDU session
3648 * @tid: tid of the BA session
3649 * @ssn: start sequence number of the session. TX/RX_STOP can pass 0. When
3650 * action is set to %IEEE80211_AMPDU_RX_START the driver passes back the
3651 * actual ssn value used to start the session and writes the value here.
3652 * @buf_size: reorder buffer size (number of subframes). Valid only when the
3653 * action is set to %IEEE80211_AMPDU_RX_START or
3654 * %IEEE80211_AMPDU_TX_OPERATIONAL
3655 * @amsdu: indicates the peer's ability to receive A-MSDU within A-MPDU.
3656 * valid when the action is set to %IEEE80211_AMPDU_TX_OPERATIONAL
3657 * @timeout: BA session timeout. Valid only when the action is set to
3658 * %IEEE80211_AMPDU_RX_START
3659 */
3660struct ieee80211_ampdu_params {
3661 enum ieee80211_ampdu_mlme_action action;
3662 struct ieee80211_sta *sta;
3663 u16 tid;
3664 u16 ssn;
3665 u16 buf_size;
3666 bool amsdu;
3667 u16 timeout;
3668};
3669
3670/**
3671 * enum ieee80211_frame_release_type - frame release reason
3672 * @IEEE80211_FRAME_RELEASE_PSPOLL: frame released for PS-Poll
3673 * @IEEE80211_FRAME_RELEASE_UAPSD: frame(s) released due to
3674 * frame received on trigger-enabled AC
3675 */
3676enum ieee80211_frame_release_type {
3677 IEEE80211_FRAME_RELEASE_PSPOLL,
3678 IEEE80211_FRAME_RELEASE_UAPSD,
3679};
3680
3681/**
3682 * enum ieee80211_rate_control_changed - flags to indicate what changed
3683 *
3684 * @IEEE80211_RC_BW_CHANGED: The bandwidth that can be used to transmit
3685 * to this station changed. The actual bandwidth is in the station
3686 * information -- for HT20/40 the IEEE80211_HT_CAP_SUP_WIDTH_20_40
3687 * flag changes, for HT and VHT the bandwidth field changes.
3688 * @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed.
3689 * @IEEE80211_RC_SUPP_RATES_CHANGED: The supported rate set of this peer
3690 * changed (in IBSS mode) due to discovering more information about
3691 * the peer.
3692 * @IEEE80211_RC_NSS_CHANGED: N_SS (number of spatial streams) was changed
3693 * by the peer
3694 */
3695enum ieee80211_rate_control_changed {
3696 IEEE80211_RC_BW_CHANGED = BIT(0),
3697 IEEE80211_RC_SMPS_CHANGED = BIT(1),
3698 IEEE80211_RC_SUPP_RATES_CHANGED = BIT(2),
3699 IEEE80211_RC_NSS_CHANGED = BIT(3),
3700};
3701
3702/**
3703 * enum ieee80211_roc_type - remain on channel type
3704 *
3705 * With the support for multi channel contexts and multi channel operations,
3706 * remain on channel operations might be limited/deferred/aborted by other
3707 * flows/operations which have higher priority (and vice versa).
3708 * Specifying the ROC type can be used by devices to prioritize the ROC
3709 * operations compared to other operations/flows.
3710 *
3711 * @IEEE80211_ROC_TYPE_NORMAL: There are no special requirements for this ROC.
3712 * @IEEE80211_ROC_TYPE_MGMT_TX: The remain on channel request is required
3713 * for sending management frames offchannel.
3714 */
3715enum ieee80211_roc_type {
3716 IEEE80211_ROC_TYPE_NORMAL = 0,
3717 IEEE80211_ROC_TYPE_MGMT_TX,
3718};
3719
3720/**
3721 * enum ieee80211_reconfig_type - reconfig type
3722 *
3723 * This enum is used by the reconfig_complete() callback to indicate what
3724 * reconfiguration type was completed.
3725 *
3726 * @IEEE80211_RECONFIG_TYPE_RESTART: hw restart type
3727 * (also due to resume() callback returning 1)
3728 * @IEEE80211_RECONFIG_TYPE_SUSPEND: suspend type (regardless
3729 * of wowlan configuration)
3730 */
3731enum ieee80211_reconfig_type {
3732 IEEE80211_RECONFIG_TYPE_RESTART,
3733 IEEE80211_RECONFIG_TYPE_SUSPEND,
3734};
3735
3736/**
3737 * struct ieee80211_prep_tx_info - prepare TX information
3738 * @duration: if non-zero, hint about the required duration,
3739 * only used with the mgd_prepare_tx() method.
3740 * @subtype: frame subtype (auth, (re)assoc, deauth, disassoc)
3741 * @success: whether the frame exchange was successful, only
3742 * used with the mgd_complete_tx() method, and then only
3743 * valid for auth and (re)assoc.
3744 * @link_id: the link id on which the frame will be TX'ed.
3745 * Only used with the mgd_prepare_tx() method.
3746 */
3747struct ieee80211_prep_tx_info {
3748 u16 duration;
3749 u16 subtype;
3750 u8 success:1;
3751 int link_id;
3752};
3753
3754/**
3755 * struct ieee80211_ops - callbacks from mac80211 to the driver
3756 *
3757 * This structure contains various callbacks that the driver may
3758 * handle or, in some cases, must handle, for example to configure
3759 * the hardware to a new channel or to transmit a frame.
3760 *
3761 * @tx: Handler that 802.11 module calls for each transmitted frame.
3762 * skb contains the buffer starting from the IEEE 802.11 header.
3763 * The low-level driver should send the frame out based on
3764 * configuration in the TX control data. This handler should,
3765 * preferably, never fail and stop queues appropriately.
3766 * Must be atomic.
3767 *
3768 * @start: Called before the first netdevice attached to the hardware
3769 * is enabled. This should turn on the hardware and must turn on
3770 * frame reception (for possibly enabled monitor interfaces.)
3771 * Returns negative error codes, these may be seen in userspace,
3772 * or zero.
3773 * When the device is started it should not have a MAC address
3774 * to avoid acknowledging frames before a non-monitor device
3775 * is added.
3776 * Must be implemented and can sleep.
3777 *
3778 * @stop: Called after last netdevice attached to the hardware
3779 * is disabled. This should turn off the hardware (at least
3780 * it must turn off frame reception.)
3781 * May be called right after add_interface if that rejects
3782 * an interface. If you added any work onto the mac80211 workqueue
3783 * you should ensure to cancel it on this callback.
3784 * Must be implemented and can sleep.
3785 *
3786 * @suspend: Suspend the device; mac80211 itself will quiesce before and
3787 * stop transmitting and doing any other configuration, and then
3788 * ask the device to suspend. This is only invoked when WoWLAN is
3789 * configured, otherwise the device is deconfigured completely and
3790 * reconfigured at resume time.
3791 * The driver may also impose special conditions under which it
3792 * wants to use the "normal" suspend (deconfigure), say if it only
3793 * supports WoWLAN when the device is associated. In this case, it
3794 * must return 1 from this function.
3795 *
3796 * @resume: If WoWLAN was configured, this indicates that mac80211 is
3797 * now resuming its operation, after this the device must be fully
3798 * functional again. If this returns an error, the only way out is
3799 * to also unregister the device. If it returns 1, then mac80211
3800 * will also go through the regular complete restart on resume.
3801 *
3802 * @set_wakeup: Enable or disable wakeup when WoWLAN configuration is
3803 * modified. The reason is that device_set_wakeup_enable() is
3804 * supposed to be called when the configuration changes, not only
3805 * in suspend().
3806 *
3807 * @add_interface: Called when a netdevice attached to the hardware is
3808 * enabled. Because it is not called for monitor mode devices, @start
3809 * and @stop must be implemented.
3810 * The driver should perform any initialization it needs before
3811 * the device can be enabled. The initial configuration for the
3812 * interface is given in the conf parameter.
3813 * The callback may refuse to add an interface by returning a
3814 * negative error code (which will be seen in userspace.)
3815 * Must be implemented and can sleep.
3816 *
3817 * @change_interface: Called when a netdevice changes type. This callback
3818 * is optional, but only if it is supported can interface types be
3819 * switched while the interface is UP. The callback may sleep.
3820 * Note that while an interface is being switched, it will not be
3821 * found by the interface iteration callbacks.
3822 *
3823 * @remove_interface: Notifies a driver that an interface is going down.
3824 * The @stop callback is called after this if it is the last interface
3825 * and no monitor interfaces are present.
3826 * When all interfaces are removed, the MAC address in the hardware
3827 * must be cleared so the device no longer acknowledges packets,
3828 * the mac_addr member of the conf structure is, however, set to the
3829 * MAC address of the device going away.
3830 * Hence, this callback must be implemented. It can sleep.
3831 *
3832 * @config: Handler for configuration requests. IEEE 802.11 code calls this
3833 * function to change hardware configuration, e.g., channel.
3834 * This function should never fail but returns a negative error code
3835 * if it does. The callback can sleep.
3836 *
3837 * @bss_info_changed: Handler for configuration requests related to BSS
3838 * parameters that may vary during BSS's lifespan, and may affect low
3839 * level driver (e.g. assoc/disassoc status, erp parameters).
3840 * This function should not be used if no BSS has been set, unless
3841 * for association indication. The @changed parameter indicates which
3842 * of the bss parameters has changed when a call is made. The callback
3843 * can sleep.
3844 * Note: this callback is called if @vif_cfg_changed or @link_info_changed
3845 * are not implemented.
3846 *
3847 * @vif_cfg_changed: Handler for configuration requests related to interface
3848 * (MLD) parameters from &struct ieee80211_vif_cfg that vary during the
3849 * lifetime of the interface (e.g. assoc status, IP addresses, etc.)
3850 * The @changed parameter indicates which value changed.
3851 * The callback can sleep.
3852 *
3853 * @link_info_changed: Handler for configuration requests related to link
3854 * parameters from &struct ieee80211_bss_conf that are related to an
3855 * individual link. e.g. legacy/HT/VHT/... rate information.
3856 * The @changed parameter indicates which value changed, and the @link_id
3857 * parameter indicates the link ID. Note that the @link_id will be 0 for
3858 * non-MLO connections.
3859 * The callback can sleep.
3860 *
3861 * @prepare_multicast: Prepare for multicast filter configuration.
3862 * This callback is optional, and its return value is passed
3863 * to configure_filter(). This callback must be atomic.
3864 *
3865 * @configure_filter: Configure the device's RX filter.
3866 * See the section "Frame filtering" for more information.
3867 * This callback must be implemented and can sleep.
3868 *
3869 * @config_iface_filter: Configure the interface's RX filter.
3870 * This callback is optional and is used to configure which frames
3871 * should be passed to mac80211. The filter_flags is the combination
3872 * of FIF_* flags. The changed_flags is a bit mask that indicates
3873 * which flags are changed.
3874 * This callback can sleep.
3875 *
3876 * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit
3877 * must be set or cleared for a given STA. Must be atomic.
3878 *
3879 * @set_key: See the section "Hardware crypto acceleration"
3880 * This callback is only called between add_interface and
3881 * remove_interface calls, i.e. while the given virtual interface
3882 * is enabled.
3883 * Returns a negative error code if the key can't be added.
3884 * The callback can sleep.
3885 *
3886 * @update_tkip_key: See the section "Hardware crypto acceleration"
3887 * This callback will be called in the context of Rx. Called for drivers
3888 * which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY.
3889 * The callback must be atomic.
3890 *
3891 * @set_rekey_data: If the device supports GTK rekeying, for example while the
3892 * host is suspended, it can assign this callback to retrieve the data
3893 * necessary to do GTK rekeying, this is the KEK, KCK and replay counter.
3894 * After rekeying was done it should (for example during resume) notify
3895 * userspace of the new replay counter using ieee80211_gtk_rekey_notify().
3896 *
3897 * @set_default_unicast_key: Set the default (unicast) key index, useful for
3898 * WEP when the device sends data packets autonomously, e.g. for ARP
3899 * offloading. The index can be 0-3, or -1 for unsetting it.
3900 *
3901 * @hw_scan: Ask the hardware to service the scan request, no need to start
3902 * the scan state machine in stack. The scan must honour the channel
3903 * configuration done by the regulatory agent in the wiphy's
3904 * registered bands. The hardware (or the driver) needs to make sure
3905 * that power save is disabled.
3906 * The @req ie/ie_len members are rewritten by mac80211 to contain the
3907 * entire IEs after the SSID, so that drivers need not look at these
3908 * at all but just send them after the SSID -- mac80211 includes the
3909 * (extended) supported rates and HT information (where applicable).
3910 * When the scan finishes, ieee80211_scan_completed() must be called;
3911 * note that it also must be called when the scan cannot finish due to
3912 * any error unless this callback returned a negative error code.
3913 * This callback is also allowed to return the special return value 1,
3914 * this indicates that hardware scan isn't desirable right now and a
3915 * software scan should be done instead. A driver wishing to use this
3916 * capability must ensure its (hardware) scan capabilities aren't
3917 * advertised as more capable than mac80211's software scan is.
3918 * The callback can sleep.
3919 *
3920 * @cancel_hw_scan: Ask the low-level tp cancel the active hw scan.
3921 * The driver should ask the hardware to cancel the scan (if possible),
3922 * but the scan will be completed only after the driver will call
3923 * ieee80211_scan_completed().
3924 * This callback is needed for wowlan, to prevent enqueueing a new
3925 * scan_work after the low-level driver was already suspended.
3926 * The callback can sleep.
3927 *
3928 * @sched_scan_start: Ask the hardware to start scanning repeatedly at
3929 * specific intervals. The driver must call the
3930 * ieee80211_sched_scan_results() function whenever it finds results.
3931 * This process will continue until sched_scan_stop is called.
3932 *
3933 * @sched_scan_stop: Tell the hardware to stop an ongoing scheduled scan.
3934 * In this case, ieee80211_sched_scan_stopped() must not be called.
3935 *
3936 * @sw_scan_start: Notifier function that is called just before a software scan
3937 * is started. Can be NULL, if the driver doesn't need this notification.
3938 * The mac_addr parameter allows supporting NL80211_SCAN_FLAG_RANDOM_ADDR,
3939 * the driver may set the NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR flag if it
3940 * can use this parameter. The callback can sleep.
3941 *
3942 * @sw_scan_complete: Notifier function that is called just after a
3943 * software scan finished. Can be NULL, if the driver doesn't need
3944 * this notification.
3945 * The callback can sleep.
3946 *
3947 * @get_stats: Return low-level statistics.
3948 * Returns zero if statistics are available.
3949 * The callback can sleep.
3950 *
3951 * @get_key_seq: If your device implements encryption in hardware and does
3952 * IV/PN assignment then this callback should be provided to read the
3953 * IV/PN for the given key from hardware.
3954 * The callback must be atomic.
3955 *
3956 * @set_frag_threshold: Configuration of fragmentation threshold. Assign this
3957 * if the device does fragmentation by itself. Note that to prevent the
3958 * stack from doing fragmentation IEEE80211_HW_SUPPORTS_TX_FRAG
3959 * should be set as well.
3960 * The callback can sleep.
3961 *
3962 * @set_rts_threshold: Configuration of RTS threshold (if device needs it)
3963 * The callback can sleep.
3964 *
3965 * @sta_add: Notifies low level driver about addition of an associated station,
3966 * AP, IBSS/WDS/mesh peer etc. This callback can sleep.
3967 *
3968 * @sta_remove: Notifies low level driver about removal of an associated
3969 * station, AP, IBSS/WDS/mesh peer etc. Note that after the callback
3970 * returns it isn't safe to use the pointer, not even RCU protected;
3971 * no RCU grace period is guaranteed between returning here and freeing
3972 * the station. See @sta_pre_rcu_remove if needed.
3973 * This callback can sleep.
3974 *
3975 * @vif_add_debugfs: Drivers can use this callback to add a debugfs vif
3976 * directory with its files. This callback should be within a
3977 * CONFIG_MAC80211_DEBUGFS conditional. This callback can sleep.
3978 *
3979 * @link_add_debugfs: Drivers can use this callback to add debugfs files
3980 * when a link is added to a mac80211 vif. This callback should be within
3981 * a CONFIG_MAC80211_DEBUGFS conditional. This callback can sleep.
3982 * For non-MLO the callback will be called once for the default bss_conf
3983 * with the vif's directory rather than a separate subdirectory.
3984 *
3985 * @sta_add_debugfs: Drivers can use this callback to add debugfs files
3986 * when a station is added to mac80211's station list. This callback
3987 * should be within a CONFIG_MAC80211_DEBUGFS conditional. This
3988 * callback can sleep.
3989 *
3990 * @link_sta_add_debugfs: Drivers can use this callback to add debugfs files
3991 * when a link is added to a mac80211 station. This callback
3992 * should be within a CONFIG_MAC80211_DEBUGFS conditional. This
3993 * callback can sleep.
3994 * For non-MLO the callback will be called once for the deflink with the
3995 * station's directory rather than a separate subdirectory.
3996 *
3997 * @sta_notify: Notifies low level driver about power state transition of an
3998 * associated station, AP, IBSS/WDS/mesh peer etc. For a VIF operating
3999 * in AP mode, this callback will not be called when the flag
4000 * %IEEE80211_HW_AP_LINK_PS is set. Must be atomic.
4001 *
4002 * @sta_set_txpwr: Configure the station tx power. This callback set the tx
4003 * power for the station.
4004 * This callback can sleep.
4005 *
4006 * @sta_state: Notifies low level driver about state transition of a
4007 * station (which can be the AP, a client, IBSS/WDS/mesh peer etc.)
4008 * This callback is mutually exclusive with @sta_add/@sta_remove.
4009 * It must not fail for down transitions but may fail for transitions
4010 * up the list of states. Also note that after the callback returns it
4011 * isn't safe to use the pointer, not even RCU protected - no RCU grace
4012 * period is guaranteed between returning here and freeing the station.
4013 * See @sta_pre_rcu_remove if needed.
4014 * The callback can sleep.
4015 *
4016 * @sta_pre_rcu_remove: Notify driver about station removal before RCU
4017 * synchronisation. This is useful if a driver needs to have station
4018 * pointers protected using RCU, it can then use this call to clear
4019 * the pointers instead of waiting for an RCU grace period to elapse
4020 * in @sta_state.
4021 * The callback can sleep.
4022 *
4023 * @sta_rc_update: Notifies the driver of changes to the bitrates that can be
4024 * used to transmit to the station. The changes are advertised with bits
4025 * from &enum ieee80211_rate_control_changed and the values are reflected
4026 * in the station data. This callback should only be used when the driver
4027 * uses hardware rate control (%IEEE80211_HW_HAS_RATE_CONTROL) since
4028 * otherwise the rate control algorithm is notified directly.
4029 * Must be atomic.
4030 * @sta_rate_tbl_update: Notifies the driver that the rate table changed. This
4031 * is only used if the configured rate control algorithm actually uses
4032 * the new rate table API, and is therefore optional. Must be atomic.
4033 *
4034 * @sta_statistics: Get statistics for this station. For example with beacon
4035 * filtering, the statistics kept by mac80211 might not be accurate, so
4036 * let the driver pre-fill the statistics. The driver can fill most of
4037 * the values (indicating which by setting the filled bitmap), but not
4038 * all of them make sense - see the source for which ones are possible.
4039 * Statistics that the driver doesn't fill will be filled by mac80211.
4040 * The callback can sleep.
4041 *
4042 * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
4043 * bursting) for a hardware TX queue.
4044 * Returns a negative error code on failure.
4045 * The callback can sleep.
4046 *
4047 * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
4048 * this is only used for IBSS mode BSSID merging and debugging. Is not a
4049 * required function.
4050 * The callback can sleep.
4051 *
4052 * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
4053 * Currently, this is only used for IBSS mode debugging. Is not a
4054 * required function.
4055 * The callback can sleep.
4056 *
4057 * @offset_tsf: Offset the TSF timer by the specified value in the
4058 * firmware/hardware. Preferred to set_tsf as it avoids delay between
4059 * calling set_tsf() and hardware getting programmed, which will show up
4060 * as TSF delay. Is not a required function.
4061 * The callback can sleep.
4062 *
4063 * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize
4064 * with other STAs in the IBSS. This is only used in IBSS mode. This
4065 * function is optional if the firmware/hardware takes full care of
4066 * TSF synchronization.
4067 * The callback can sleep.
4068 *
4069 * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
4070 * This is needed only for IBSS mode and the result of this function is
4071 * used to determine whether to reply to Probe Requests.
4072 * Returns non-zero if this device sent the last beacon.
4073 * The callback can sleep.
4074 *
4075 * @get_survey: Return per-channel survey information
4076 *
4077 * @rfkill_poll: Poll rfkill hardware state. If you need this, you also
4078 * need to set wiphy->rfkill_poll to %true before registration,
4079 * and need to call wiphy_rfkill_set_hw_state() in the callback.
4080 * The callback can sleep.
4081 *
4082 * @set_coverage_class: Set slot time for given coverage class as specified
4083 * in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout
4084 * accordingly; coverage class equals to -1 to enable ACK timeout
4085 * estimation algorithm (dynack). To disable dynack set valid value for
4086 * coverage class. This callback is not required and may sleep.
4087 *
4088 * @testmode_cmd: Implement a cfg80211 test mode command. The passed @vif may
4089 * be %NULL. The callback can sleep.
4090 * @testmode_dump: Implement a cfg80211 test mode dump. The callback can sleep.
4091 *
4092 * @flush: Flush all pending frames from the hardware queue, making sure
4093 * that the hardware queues are empty. The @queues parameter is a bitmap
4094 * of queues to flush, which is useful if different virtual interfaces
4095 * use different hardware queues; it may also indicate all queues.
4096 * If the parameter @drop is set to %true, pending frames may be dropped.
4097 * Note that vif can be NULL.
4098 * The callback can sleep.
4099 *
4100 * @flush_sta: Flush or drop all pending frames from the hardware queue(s) for
4101 * the given station, as it's about to be removed.
4102 * The callback can sleep.
4103 *
4104 * @channel_switch: Drivers that need (or want) to offload the channel
4105 * switch operation for CSAs received from the AP may implement this
4106 * callback. They must then call ieee80211_chswitch_done() to indicate
4107 * completion of the channel switch.
4108 *
4109 * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device.
4110 * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may
4111 * reject TX/RX mask combinations they cannot support by returning -EINVAL
4112 * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX).
4113 *
4114 * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant).
4115 *
4116 * @remain_on_channel: Starts an off-channel period on the given channel, must
4117 * call back to ieee80211_ready_on_channel() when on that channel. Note
4118 * that normal channel traffic is not stopped as this is intended for hw
4119 * offload. Frames to transmit on the off-channel channel are transmitted
4120 * normally except for the %IEEE80211_TX_CTL_TX_OFFCHAN flag. When the
4121 * duration (which will always be non-zero) expires, the driver must call
4122 * ieee80211_remain_on_channel_expired().
4123 * Note that this callback may be called while the device is in IDLE and
4124 * must be accepted in this case.
4125 * This callback may sleep.
4126 * @cancel_remain_on_channel: Requests that an ongoing off-channel period is
4127 * aborted before it expires. This callback may sleep.
4128 *
4129 * @set_ringparam: Set tx and rx ring sizes.
4130 *
4131 * @get_ringparam: Get tx and rx ring current and maximum sizes.
4132 *
4133 * @tx_frames_pending: Check if there is any pending frame in the hardware
4134 * queues before entering power save.
4135 *
4136 * @set_bitrate_mask: Set a mask of rates to be used for rate control selection
4137 * when transmitting a frame. Currently only legacy rates are handled.
4138 * The callback can sleep.
4139 * @event_callback: Notify driver about any event in mac80211. See
4140 * &enum ieee80211_event_type for the different types.
4141 * The callback must be atomic.
4142 *
4143 * @release_buffered_frames: Release buffered frames according to the given
4144 * parameters. In the case where the driver buffers some frames for
4145 * sleeping stations mac80211 will use this callback to tell the driver
4146 * to release some frames, either for PS-poll or uAPSD.
4147 * Note that if the @more_data parameter is %false the driver must check
4148 * if there are more frames on the given TIDs, and if there are more than
4149 * the frames being released then it must still set the more-data bit in
4150 * the frame. If the @more_data parameter is %true, then of course the
4151 * more-data bit must always be set.
4152 * The @tids parameter tells the driver which TIDs to release frames
4153 * from, for PS-poll it will always have only a single bit set.
4154 * In the case this is used for a PS-poll initiated release, the
4155 * @num_frames parameter will always be 1 so code can be shared. In
4156 * this case the driver must also set %IEEE80211_TX_STATUS_EOSP flag
4157 * on the TX status (and must report TX status) so that the PS-poll
4158 * period is properly ended. This is used to avoid sending multiple
4159 * responses for a retried PS-poll frame.
4160 * In the case this is used for uAPSD, the @num_frames parameter may be
4161 * bigger than one, but the driver may send fewer frames (it must send
4162 * at least one, however). In this case it is also responsible for
4163 * setting the EOSP flag in the QoS header of the frames. Also, when the
4164 * service period ends, the driver must set %IEEE80211_TX_STATUS_EOSP
4165 * on the last frame in the SP. Alternatively, it may call the function
4166 * ieee80211_sta_eosp() to inform mac80211 of the end of the SP.
4167 * This callback must be atomic.
4168 * @allow_buffered_frames: Prepare device to allow the given number of frames
4169 * to go out to the given station. The frames will be sent by mac80211
4170 * via the usual TX path after this call. The TX information for frames
4171 * released will also have the %IEEE80211_TX_CTL_NO_PS_BUFFER flag set
4172 * and the last one will also have %IEEE80211_TX_STATUS_EOSP set. In case
4173 * frames from multiple TIDs are released and the driver might reorder
4174 * them between the TIDs, it must set the %IEEE80211_TX_STATUS_EOSP flag
4175 * on the last frame and clear it on all others and also handle the EOSP
4176 * bit in the QoS header correctly. Alternatively, it can also call the
4177 * ieee80211_sta_eosp() function.
4178 * The @tids parameter is a bitmap and tells the driver which TIDs the
4179 * frames will be on; it will at most have two bits set.
4180 * This callback must be atomic.
4181 *
4182 * @get_et_sset_count: Ethtool API to get string-set count.
4183 * Note that the wiphy mutex is not held for this callback since it's
4184 * expected to return a static value.
4185 *
4186 * @get_et_stats: Ethtool API to get a set of u64 stats.
4187 *
4188 * @get_et_strings: Ethtool API to get a set of strings to describe stats
4189 * and perhaps other supported types of ethtool data-sets.
4190 * Note that the wiphy mutex is not held for this callback since it's
4191 * expected to return a static value.
4192 *
4193 * @mgd_prepare_tx: Prepare for transmitting a management frame for association
4194 * before associated. In multi-channel scenarios, a virtual interface is
4195 * bound to a channel before it is associated, but as it isn't associated
4196 * yet it need not necessarily be given airtime, in particular since any
4197 * transmission to a P2P GO needs to be synchronized against the GO's
4198 * powersave state. mac80211 will call this function before transmitting a
4199 * management frame prior to having successfully associated to allow the
4200 * driver to give it channel time for the transmission, to get a response
4201 * and to be able to synchronize with the GO.
4202 * For drivers that set %IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP, mac80211
4203 * would also call this function before transmitting a deauthentication
4204 * frame in case that no beacon was heard from the AP/P2P GO.
4205 * The callback will be called before each transmission and upon return
4206 * mac80211 will transmit the frame right away.
4207 * Additional information is passed in the &struct ieee80211_prep_tx_info
4208 * data. If duration there is greater than zero, mac80211 hints to the
4209 * driver the duration for which the operation is requested.
4210 * The callback is optional and can (should!) sleep.
4211 * @mgd_complete_tx: Notify the driver that the response frame for a previously
4212 * transmitted frame announced with @mgd_prepare_tx was received, the data
4213 * is filled similarly to @mgd_prepare_tx though the duration is not used.
4214 *
4215 * @mgd_protect_tdls_discover: Protect a TDLS discovery session. After sending
4216 * a TDLS discovery-request, we expect a reply to arrive on the AP's
4217 * channel. We must stay on the channel (no PSM, scan, etc.), since a TDLS
4218 * setup-response is a direct packet not buffered by the AP.
4219 * mac80211 will call this function just before the transmission of a TDLS
4220 * discovery-request. The recommended period of protection is at least
4221 * 2 * (DTIM period).
4222 * The callback is optional and can sleep.
4223 *
4224 * @add_chanctx: Notifies device driver about new channel context creation.
4225 * This callback may sleep.
4226 * @remove_chanctx: Notifies device driver about channel context destruction.
4227 * This callback may sleep.
4228 * @change_chanctx: Notifies device driver about channel context changes that
4229 * may happen when combining different virtual interfaces on the same
4230 * channel context with different settings
4231 * This callback may sleep.
4232 * @assign_vif_chanctx: Notifies device driver about channel context being bound
4233 * to vif. Possible use is for hw queue remapping.
4234 * This callback may sleep.
4235 * @unassign_vif_chanctx: Notifies device driver about channel context being
4236 * unbound from vif.
4237 * This callback may sleep.
4238 * @switch_vif_chanctx: switch a number of vifs from one chanctx to
4239 * another, as specified in the list of
4240 * @ieee80211_vif_chanctx_switch passed to the driver, according
4241 * to the mode defined in &ieee80211_chanctx_switch_mode.
4242 * This callback may sleep.
4243 *
4244 * @start_ap: Start operation on the AP interface, this is called after all the
4245 * information in bss_conf is set and beacon can be retrieved. A channel
4246 * context is bound before this is called. Note that if the driver uses
4247 * software scan or ROC, this (and @stop_ap) isn't called when the AP is
4248 * just "paused" for scanning/ROC, which is indicated by the beacon being
4249 * disabled/enabled via @bss_info_changed.
4250 * @stop_ap: Stop operation on the AP interface.
4251 *
4252 * @reconfig_complete: Called after a call to ieee80211_restart_hw() and
4253 * during resume, when the reconfiguration has completed.
4254 * This can help the driver implement the reconfiguration step (and
4255 * indicate mac80211 is ready to receive frames).
4256 * This callback may sleep.
4257 *
4258 * @ipv6_addr_change: IPv6 address assignment on the given interface changed.
4259 * Currently, this is only called for managed or P2P client interfaces.
4260 * This callback is optional; it must not sleep.
4261 *
4262 * @channel_switch_beacon: Starts a channel switch to a new channel.
4263 * Beacons are modified to include CSA or ECSA IEs before calling this
4264 * function. The corresponding count fields in these IEs must be
4265 * decremented, and when they reach 1 the driver must call
4266 * ieee80211_csa_finish(). Drivers which use ieee80211_beacon_get()
4267 * get the csa counter decremented by mac80211, but must check if it is
4268 * 1 using ieee80211_beacon_counter_is_complete() after the beacon has been
4269 * transmitted and then call ieee80211_csa_finish().
4270 * If the CSA count starts as zero or 1, this function will not be called,
4271 * since there won't be any time to beacon before the switch anyway.
4272 * @pre_channel_switch: This is an optional callback that is called
4273 * before a channel switch procedure is started (ie. when a STA
4274 * gets a CSA or a userspace initiated channel-switch), allowing
4275 * the driver to prepare for the channel switch.
4276 * @post_channel_switch: This is an optional callback that is called
4277 * after a channel switch procedure is completed, allowing the
4278 * driver to go back to a normal configuration.
4279 * @abort_channel_switch: This is an optional callback that is called
4280 * when channel switch procedure was aborted, allowing the
4281 * driver to go back to a normal configuration.
4282 * @channel_switch_rx_beacon: This is an optional callback that is called
4283 * when channel switch procedure is in progress and additional beacon with
4284 * CSA IE was received, allowing driver to track changes in count.
4285 * @join_ibss: Join an IBSS (on an IBSS interface); this is called after all
4286 * information in bss_conf is set up and the beacon can be retrieved. A
4287 * channel context is bound before this is called.
4288 * @leave_ibss: Leave the IBSS again.
4289 *
4290 * @get_expected_throughput: extract the expected throughput towards the
4291 * specified station. The returned value is expressed in Kbps. It returns 0
4292 * if the RC algorithm does not have proper data to provide.
4293 *
4294 * @get_txpower: get current maximum tx power (in dBm) based on configuration
4295 * and hardware limits.
4296 *
4297 * @tdls_channel_switch: Start channel-switching with a TDLS peer. The driver
4298 * is responsible for continually initiating channel-switching operations
4299 * and returning to the base channel for communication with the AP. The
4300 * driver receives a channel-switch request template and the location of
4301 * the switch-timing IE within the template as part of the invocation.
4302 * The template is valid only within the call, and the driver can
4303 * optionally copy the skb for further re-use.
4304 * @tdls_cancel_channel_switch: Stop channel-switching with a TDLS peer. Both
4305 * peers must be on the base channel when the call completes.
4306 * @tdls_recv_channel_switch: a TDLS channel-switch related frame (request or
4307 * response) has been received from a remote peer. The driver gets
4308 * parameters parsed from the incoming frame and may use them to continue
4309 * an ongoing channel-switch operation. In addition, a channel-switch
4310 * response template is provided, together with the location of the
4311 * switch-timing IE within the template. The skb can only be used within
4312 * the function call.
4313 *
4314 * @wake_tx_queue: Called when new packets have been added to the queue.
4315 * @sync_rx_queues: Process all pending frames in RSS queues. This is a
4316 * synchronization which is needed in case driver has in its RSS queues
4317 * pending frames that were received prior to the control path action
4318 * currently taken (e.g. disassociation) but are not processed yet.
4319 *
4320 * @start_nan: join an existing NAN cluster, or create a new one.
4321 * @stop_nan: leave the NAN cluster.
4322 * @nan_change_conf: change NAN configuration. The data in cfg80211_nan_conf
4323 * contains full new configuration and changes specify which parameters
4324 * are changed with respect to the last NAN config.
4325 * The driver gets both full configuration and the changed parameters since
4326 * some devices may need the full configuration while others need only the
4327 * changed parameters.
4328 * @add_nan_func: Add a NAN function. Returns 0 on success. The data in
4329 * cfg80211_nan_func must not be referenced outside the scope of
4330 * this call.
4331 * @del_nan_func: Remove a NAN function. The driver must call
4332 * ieee80211_nan_func_terminated() with
4333 * NL80211_NAN_FUNC_TERM_REASON_USER_REQUEST reason code upon removal.
4334 * @can_aggregate_in_amsdu: Called in order to determine if HW supports
4335 * aggregating two specific frames in the same A-MSDU. The relation
4336 * between the skbs should be symmetric and transitive. Note that while
4337 * skb is always a real frame, head may or may not be an A-MSDU.
4338 * @get_ftm_responder_stats: Retrieve FTM responder statistics, if available.
4339 * Statistics should be cumulative, currently no way to reset is provided.
4340 *
4341 * @start_pmsr: start peer measurement (e.g. FTM) (this call can sleep)
4342 * @abort_pmsr: abort peer measurement (this call can sleep)
4343 * @set_tid_config: Apply TID specific configurations. This callback may sleep.
4344 * @reset_tid_config: Reset TID specific configuration for the peer.
4345 * This callback may sleep.
4346 * @update_vif_offload: Update virtual interface offload flags
4347 * This callback may sleep.
4348 * @sta_set_4addr: Called to notify the driver when a station starts/stops using
4349 * 4-address mode
4350 * @set_sar_specs: Update the SAR (TX power) settings.
4351 * @sta_set_decap_offload: Called to notify the driver when a station is allowed
4352 * to use rx decapsulation offload
4353 * @add_twt_setup: Update hw with TWT agreement parameters received from the peer.
4354 * This callback allows the hw to check if requested parameters
4355 * are supported and if there is enough room for a new agreement.
4356 * The hw is expected to set agreement result in the req_type field of
4357 * twt structure.
4358 * @twt_teardown_request: Update the hw with TWT teardown request received
4359 * from the peer.
4360 * @set_radar_background: Configure dedicated offchannel chain available for
4361 * radar/CAC detection on some hw. This chain can't be used to transmit
4362 * or receive frames and it is bounded to a running wdev.
4363 * Background radar/CAC detection allows to avoid the CAC downtime
4364 * switching to a different channel during CAC detection on the selected
4365 * radar channel.
4366 * The caller is expected to set chandef pointer to NULL in order to
4367 * disable background CAC/radar detection.
4368 * @net_fill_forward_path: Called from .ndo_fill_forward_path in order to
4369 * resolve a path for hardware flow offloading
4370 * @can_activate_links: Checks if a specific active_links bitmap is
4371 * supported by the driver.
4372 * @change_vif_links: Change the valid links on an interface, note that while
4373 * removing the old link information is still valid (link_conf pointer),
4374 * but may immediately disappear after the function returns. The old or
4375 * new links bitmaps may be 0 if going from/to a non-MLO situation.
4376 * The @old array contains pointers to the old bss_conf structures
4377 * that were already removed, in case they're needed.
4378 * This callback can sleep.
4379 * @change_sta_links: Change the valid links of a station, similar to
4380 * @change_vif_links. This callback can sleep.
4381 * Note that a sta can also be inserted or removed with valid links,
4382 * i.e. passed to @sta_add/@sta_state with sta->valid_links not zero.
4383 * In fact, cannot change from having valid_links and not having them.
4384 * @set_hw_timestamp: Enable/disable HW timestamping of TM/FTM frames. This is
4385 * not restored at HW reset by mac80211 so drivers need to take care of
4386 * that.
4387 * @net_setup_tc: Called from .ndo_setup_tc in order to prepare hardware
4388 * flow offloading for flows originating from the vif.
4389 * Note that the driver must not assume that the vif driver_data is valid
4390 * at this point, since the callback can be called during netdev teardown.
4391 * @can_neg_ttlm: for managed interface, requests the driver to determine
4392 * if the requested TID-To-Link mapping can be accepted or not.
4393 * If it's not accepted the driver may suggest a preferred mapping and
4394 * modify @ttlm parameter with the suggested TID-to-Link mapping.
4395 */
4396struct ieee80211_ops {
4397 void (*tx)(struct ieee80211_hw *hw,
4398 struct ieee80211_tx_control *control,
4399 struct sk_buff *skb);
4400 int (*start)(struct ieee80211_hw *hw);
4401 void (*stop)(struct ieee80211_hw *hw);
4402#ifdef CONFIG_PM
4403 int (*suspend)(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan);
4404 int (*resume)(struct ieee80211_hw *hw);
4405 void (*set_wakeup)(struct ieee80211_hw *hw, bool enabled);
4406#endif
4407 int (*add_interface)(struct ieee80211_hw *hw,
4408 struct ieee80211_vif *vif);
4409 int (*change_interface)(struct ieee80211_hw *hw,
4410 struct ieee80211_vif *vif,
4411 enum nl80211_iftype new_type, bool p2p);
4412 void (*remove_interface)(struct ieee80211_hw *hw,
4413 struct ieee80211_vif *vif);
4414 int (*config)(struct ieee80211_hw *hw, u32 changed);
4415 void (*bss_info_changed)(struct ieee80211_hw *hw,
4416 struct ieee80211_vif *vif,
4417 struct ieee80211_bss_conf *info,
4418 u64 changed);
4419 void (*vif_cfg_changed)(struct ieee80211_hw *hw,
4420 struct ieee80211_vif *vif,
4421 u64 changed);
4422 void (*link_info_changed)(struct ieee80211_hw *hw,
4423 struct ieee80211_vif *vif,
4424 struct ieee80211_bss_conf *info,
4425 u64 changed);
4426
4427 int (*start_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4428 struct ieee80211_bss_conf *link_conf);
4429 void (*stop_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4430 struct ieee80211_bss_conf *link_conf);
4431
4432 u64 (*prepare_multicast)(struct ieee80211_hw *hw,
4433 struct netdev_hw_addr_list *mc_list);
4434 void (*configure_filter)(struct ieee80211_hw *hw,
4435 unsigned int changed_flags,
4436 unsigned int *total_flags,
4437 u64 multicast);
4438 void (*config_iface_filter)(struct ieee80211_hw *hw,
4439 struct ieee80211_vif *vif,
4440 unsigned int filter_flags,
4441 unsigned int changed_flags);
4442 int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
4443 bool set);
4444 int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd,
4445 struct ieee80211_vif *vif, struct ieee80211_sta *sta,
4446 struct ieee80211_key_conf *key);
4447 void (*update_tkip_key)(struct ieee80211_hw *hw,
4448 struct ieee80211_vif *vif,
4449 struct ieee80211_key_conf *conf,
4450 struct ieee80211_sta *sta,
4451 u32 iv32, u16 *phase1key);
4452 void (*set_rekey_data)(struct ieee80211_hw *hw,
4453 struct ieee80211_vif *vif,
4454 struct cfg80211_gtk_rekey_data *data);
4455 void (*set_default_unicast_key)(struct ieee80211_hw *hw,
4456 struct ieee80211_vif *vif, int idx);
4457 int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4458 struct ieee80211_scan_request *req);
4459 void (*cancel_hw_scan)(struct ieee80211_hw *hw,
4460 struct ieee80211_vif *vif);
4461 int (*sched_scan_start)(struct ieee80211_hw *hw,
4462 struct ieee80211_vif *vif,
4463 struct cfg80211_sched_scan_request *req,
4464 struct ieee80211_scan_ies *ies);
4465 int (*sched_scan_stop)(struct ieee80211_hw *hw,
4466 struct ieee80211_vif *vif);
4467 void (*sw_scan_start)(struct ieee80211_hw *hw,
4468 struct ieee80211_vif *vif,
4469 const u8 *mac_addr);
4470 void (*sw_scan_complete)(struct ieee80211_hw *hw,
4471 struct ieee80211_vif *vif);
4472 int (*get_stats)(struct ieee80211_hw *hw,
4473 struct ieee80211_low_level_stats *stats);
4474 void (*get_key_seq)(struct ieee80211_hw *hw,
4475 struct ieee80211_key_conf *key,
4476 struct ieee80211_key_seq *seq);
4477 int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);
4478 int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
4479 int (*sta_add)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4480 struct ieee80211_sta *sta);
4481 int (*sta_remove)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4482 struct ieee80211_sta *sta);
4483#ifdef CONFIG_MAC80211_DEBUGFS
4484 void (*vif_add_debugfs)(struct ieee80211_hw *hw,
4485 struct ieee80211_vif *vif);
4486 void (*link_add_debugfs)(struct ieee80211_hw *hw,
4487 struct ieee80211_vif *vif,
4488 struct ieee80211_bss_conf *link_conf,
4489 struct dentry *dir);
4490 void (*sta_add_debugfs)(struct ieee80211_hw *hw,
4491 struct ieee80211_vif *vif,
4492 struct ieee80211_sta *sta,
4493 struct dentry *dir);
4494 void (*link_sta_add_debugfs)(struct ieee80211_hw *hw,
4495 struct ieee80211_vif *vif,
4496 struct ieee80211_link_sta *link_sta,
4497 struct dentry *dir);
4498#endif
4499 void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4500 enum sta_notify_cmd, struct ieee80211_sta *sta);
4501 int (*sta_set_txpwr)(struct ieee80211_hw *hw,
4502 struct ieee80211_vif *vif,
4503 struct ieee80211_sta *sta);
4504 int (*sta_state)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4505 struct ieee80211_sta *sta,
4506 enum ieee80211_sta_state old_state,
4507 enum ieee80211_sta_state new_state);
4508 void (*sta_pre_rcu_remove)(struct ieee80211_hw *hw,
4509 struct ieee80211_vif *vif,
4510 struct ieee80211_sta *sta);
4511 void (*sta_rc_update)(struct ieee80211_hw *hw,
4512 struct ieee80211_vif *vif,
4513 struct ieee80211_sta *sta,
4514 u32 changed);
4515 void (*sta_rate_tbl_update)(struct ieee80211_hw *hw,
4516 struct ieee80211_vif *vif,
4517 struct ieee80211_sta *sta);
4518 void (*sta_statistics)(struct ieee80211_hw *hw,
4519 struct ieee80211_vif *vif,
4520 struct ieee80211_sta *sta,
4521 struct station_info *sinfo);
4522 int (*conf_tx)(struct ieee80211_hw *hw,
4523 struct ieee80211_vif *vif,
4524 unsigned int link_id, u16 ac,
4525 const struct ieee80211_tx_queue_params *params);
4526 u64 (*get_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
4527 void (*set_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4528 u64 tsf);
4529 void (*offset_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4530 s64 offset);
4531 void (*reset_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
4532 int (*tx_last_beacon)(struct ieee80211_hw *hw);
4533
4534 /**
4535 * @ampdu_action:
4536 * Perform a certain A-MPDU action.
4537 * The RA/TID combination determines the destination and TID we want
4538 * the ampdu action to be performed for. The action is defined through
4539 * ieee80211_ampdu_mlme_action.
4540 * When the action is set to %IEEE80211_AMPDU_TX_OPERATIONAL the driver
4541 * may neither send aggregates containing more subframes than @buf_size
4542 * nor send aggregates in a way that lost frames would exceed the
4543 * buffer size. If just limiting the aggregate size, this would be
4544 * possible with a buf_size of 8:
4545 *
4546 * - ``TX: 1.....7``
4547 * - ``RX: 2....7`` (lost frame #1)
4548 * - ``TX: 8..1...``
4549 *
4550 * which is invalid since #1 was now re-transmitted well past the
4551 * buffer size of 8. Correct ways to retransmit #1 would be:
4552 *
4553 * - ``TX: 1 or``
4554 * - ``TX: 18 or``
4555 * - ``TX: 81``
4556 *
4557 * Even ``189`` would be wrong since 1 could be lost again.
4558 *
4559 * Returns a negative error code on failure. The driver may return
4560 * %IEEE80211_AMPDU_TX_START_IMMEDIATE for %IEEE80211_AMPDU_TX_START
4561 * if the session can start immediately.
4562 *
4563 * The callback can sleep.
4564 */
4565 int (*ampdu_action)(struct ieee80211_hw *hw,
4566 struct ieee80211_vif *vif,
4567 struct ieee80211_ampdu_params *params);
4568 int (*get_survey)(struct ieee80211_hw *hw, int idx,
4569 struct survey_info *survey);
4570 void (*rfkill_poll)(struct ieee80211_hw *hw);
4571 void (*set_coverage_class)(struct ieee80211_hw *hw, s16 coverage_class);
4572#ifdef CONFIG_NL80211_TESTMODE
4573 int (*testmode_cmd)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4574 void *data, int len);
4575 int (*testmode_dump)(struct ieee80211_hw *hw, struct sk_buff *skb,
4576 struct netlink_callback *cb,
4577 void *data, int len);
4578#endif
4579 void (*flush)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4580 u32 queues, bool drop);
4581 void (*flush_sta)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4582 struct ieee80211_sta *sta);
4583 void (*channel_switch)(struct ieee80211_hw *hw,
4584 struct ieee80211_vif *vif,
4585 struct ieee80211_channel_switch *ch_switch);
4586 int (*set_antenna)(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant);
4587 int (*get_antenna)(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant);
4588
4589 int (*remain_on_channel)(struct ieee80211_hw *hw,
4590 struct ieee80211_vif *vif,
4591 struct ieee80211_channel *chan,
4592 int duration,
4593 enum ieee80211_roc_type type);
4594 int (*cancel_remain_on_channel)(struct ieee80211_hw *hw,
4595 struct ieee80211_vif *vif);
4596 int (*set_ringparam)(struct ieee80211_hw *hw, u32 tx, u32 rx);
4597 void (*get_ringparam)(struct ieee80211_hw *hw,
4598 u32 *tx, u32 *tx_max, u32 *rx, u32 *rx_max);
4599 bool (*tx_frames_pending)(struct ieee80211_hw *hw);
4600 int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4601 const struct cfg80211_bitrate_mask *mask);
4602 void (*event_callback)(struct ieee80211_hw *hw,
4603 struct ieee80211_vif *vif,
4604 const struct ieee80211_event *event);
4605
4606 void (*allow_buffered_frames)(struct ieee80211_hw *hw,
4607 struct ieee80211_sta *sta,
4608 u16 tids, int num_frames,
4609 enum ieee80211_frame_release_type reason,
4610 bool more_data);
4611 void (*release_buffered_frames)(struct ieee80211_hw *hw,
4612 struct ieee80211_sta *sta,
4613 u16 tids, int num_frames,
4614 enum ieee80211_frame_release_type reason,
4615 bool more_data);
4616
4617 int (*get_et_sset_count)(struct ieee80211_hw *hw,
4618 struct ieee80211_vif *vif, int sset);
4619 void (*get_et_stats)(struct ieee80211_hw *hw,
4620 struct ieee80211_vif *vif,
4621 struct ethtool_stats *stats, u64 *data);
4622 void (*get_et_strings)(struct ieee80211_hw *hw,
4623 struct ieee80211_vif *vif,
4624 u32 sset, u8 *data);
4625
4626 void (*mgd_prepare_tx)(struct ieee80211_hw *hw,
4627 struct ieee80211_vif *vif,
4628 struct ieee80211_prep_tx_info *info);
4629 void (*mgd_complete_tx)(struct ieee80211_hw *hw,
4630 struct ieee80211_vif *vif,
4631 struct ieee80211_prep_tx_info *info);
4632
4633 void (*mgd_protect_tdls_discover)(struct ieee80211_hw *hw,
4634 struct ieee80211_vif *vif,
4635 unsigned int link_id);
4636
4637 int (*add_chanctx)(struct ieee80211_hw *hw,
4638 struct ieee80211_chanctx_conf *ctx);
4639 void (*remove_chanctx)(struct ieee80211_hw *hw,
4640 struct ieee80211_chanctx_conf *ctx);
4641 void (*change_chanctx)(struct ieee80211_hw *hw,
4642 struct ieee80211_chanctx_conf *ctx,
4643 u32 changed);
4644 int (*assign_vif_chanctx)(struct ieee80211_hw *hw,
4645 struct ieee80211_vif *vif,
4646 struct ieee80211_bss_conf *link_conf,
4647 struct ieee80211_chanctx_conf *ctx);
4648 void (*unassign_vif_chanctx)(struct ieee80211_hw *hw,
4649 struct ieee80211_vif *vif,
4650 struct ieee80211_bss_conf *link_conf,
4651 struct ieee80211_chanctx_conf *ctx);
4652 int (*switch_vif_chanctx)(struct ieee80211_hw *hw,
4653 struct ieee80211_vif_chanctx_switch *vifs,
4654 int n_vifs,
4655 enum ieee80211_chanctx_switch_mode mode);
4656
4657 void (*reconfig_complete)(struct ieee80211_hw *hw,
4658 enum ieee80211_reconfig_type reconfig_type);
4659
4660#if IS_ENABLED(CONFIG_IPV6)
4661 void (*ipv6_addr_change)(struct ieee80211_hw *hw,
4662 struct ieee80211_vif *vif,
4663 struct inet6_dev *idev);
4664#endif
4665 void (*channel_switch_beacon)(struct ieee80211_hw *hw,
4666 struct ieee80211_vif *vif,
4667 struct cfg80211_chan_def *chandef);
4668 int (*pre_channel_switch)(struct ieee80211_hw *hw,
4669 struct ieee80211_vif *vif,
4670 struct ieee80211_channel_switch *ch_switch);
4671
4672 int (*post_channel_switch)(struct ieee80211_hw *hw,
4673 struct ieee80211_vif *vif,
4674 struct ieee80211_bss_conf *link_conf);
4675 void (*abort_channel_switch)(struct ieee80211_hw *hw,
4676 struct ieee80211_vif *vif,
4677 struct ieee80211_bss_conf *link_conf);
4678 void (*channel_switch_rx_beacon)(struct ieee80211_hw *hw,
4679 struct ieee80211_vif *vif,
4680 struct ieee80211_channel_switch *ch_switch);
4681
4682 int (*join_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
4683 void (*leave_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
4684 u32 (*get_expected_throughput)(struct ieee80211_hw *hw,
4685 struct ieee80211_sta *sta);
4686 int (*get_txpower)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4687 int *dbm);
4688
4689 int (*tdls_channel_switch)(struct ieee80211_hw *hw,
4690 struct ieee80211_vif *vif,
4691 struct ieee80211_sta *sta, u8 oper_class,
4692 struct cfg80211_chan_def *chandef,
4693 struct sk_buff *tmpl_skb, u32 ch_sw_tm_ie);
4694 void (*tdls_cancel_channel_switch)(struct ieee80211_hw *hw,
4695 struct ieee80211_vif *vif,
4696 struct ieee80211_sta *sta);
4697 void (*tdls_recv_channel_switch)(struct ieee80211_hw *hw,
4698 struct ieee80211_vif *vif,
4699 struct ieee80211_tdls_ch_sw_params *params);
4700
4701 void (*wake_tx_queue)(struct ieee80211_hw *hw,
4702 struct ieee80211_txq *txq);
4703 void (*sync_rx_queues)(struct ieee80211_hw *hw);
4704
4705 int (*start_nan)(struct ieee80211_hw *hw,
4706 struct ieee80211_vif *vif,
4707 struct cfg80211_nan_conf *conf);
4708 int (*stop_nan)(struct ieee80211_hw *hw,
4709 struct ieee80211_vif *vif);
4710 int (*nan_change_conf)(struct ieee80211_hw *hw,
4711 struct ieee80211_vif *vif,
4712 struct cfg80211_nan_conf *conf, u32 changes);
4713 int (*add_nan_func)(struct ieee80211_hw *hw,
4714 struct ieee80211_vif *vif,
4715 const struct cfg80211_nan_func *nan_func);
4716 void (*del_nan_func)(struct ieee80211_hw *hw,
4717 struct ieee80211_vif *vif,
4718 u8 instance_id);
4719 bool (*can_aggregate_in_amsdu)(struct ieee80211_hw *hw,
4720 struct sk_buff *head,
4721 struct sk_buff *skb);
4722 int (*get_ftm_responder_stats)(struct ieee80211_hw *hw,
4723 struct ieee80211_vif *vif,
4724 struct cfg80211_ftm_responder_stats *ftm_stats);
4725 int (*start_pmsr)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4726 struct cfg80211_pmsr_request *request);
4727 void (*abort_pmsr)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4728 struct cfg80211_pmsr_request *request);
4729 int (*set_tid_config)(struct ieee80211_hw *hw,
4730 struct ieee80211_vif *vif,
4731 struct ieee80211_sta *sta,
4732 struct cfg80211_tid_config *tid_conf);
4733 int (*reset_tid_config)(struct ieee80211_hw *hw,
4734 struct ieee80211_vif *vif,
4735 struct ieee80211_sta *sta, u8 tids);
4736 void (*update_vif_offload)(struct ieee80211_hw *hw,
4737 struct ieee80211_vif *vif);
4738 void (*sta_set_4addr)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4739 struct ieee80211_sta *sta, bool enabled);
4740 int (*set_sar_specs)(struct ieee80211_hw *hw,
4741 const struct cfg80211_sar_specs *sar);
4742 void (*sta_set_decap_offload)(struct ieee80211_hw *hw,
4743 struct ieee80211_vif *vif,
4744 struct ieee80211_sta *sta, bool enabled);
4745 void (*add_twt_setup)(struct ieee80211_hw *hw,
4746 struct ieee80211_sta *sta,
4747 struct ieee80211_twt_setup *twt);
4748 void (*twt_teardown_request)(struct ieee80211_hw *hw,
4749 struct ieee80211_sta *sta, u8 flowid);
4750 int (*set_radar_background)(struct ieee80211_hw *hw,
4751 struct cfg80211_chan_def *chandef);
4752 int (*net_fill_forward_path)(struct ieee80211_hw *hw,
4753 struct ieee80211_vif *vif,
4754 struct ieee80211_sta *sta,
4755 struct net_device_path_ctx *ctx,
4756 struct net_device_path *path);
4757 bool (*can_activate_links)(struct ieee80211_hw *hw,
4758 struct ieee80211_vif *vif,
4759 u16 active_links);
4760 int (*change_vif_links)(struct ieee80211_hw *hw,
4761 struct ieee80211_vif *vif,
4762 u16 old_links, u16 new_links,
4763 struct ieee80211_bss_conf *old[IEEE80211_MLD_MAX_NUM_LINKS]);
4764 int (*change_sta_links)(struct ieee80211_hw *hw,
4765 struct ieee80211_vif *vif,
4766 struct ieee80211_sta *sta,
4767 u16 old_links, u16 new_links);
4768 int (*set_hw_timestamp)(struct ieee80211_hw *hw,
4769 struct ieee80211_vif *vif,
4770 struct cfg80211_set_hw_timestamp *hwts);
4771 int (*net_setup_tc)(struct ieee80211_hw *hw,
4772 struct ieee80211_vif *vif,
4773 struct net_device *dev,
4774 enum tc_setup_type type,
4775 void *type_data);
4776 enum ieee80211_neg_ttlm_res
4777 (*can_neg_ttlm)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4778 struct ieee80211_neg_ttlm *ttlm);
4779};
4780
4781/**
4782 * ieee80211_alloc_hw_nm - Allocate a new hardware device
4783 *
4784 * This must be called once for each hardware device. The returned pointer
4785 * must be used to refer to this device when calling other functions.
4786 * mac80211 allocates a private data area for the driver pointed to by
4787 * @priv in &struct ieee80211_hw, the size of this area is given as
4788 * @priv_data_len.
4789 *
4790 * @priv_data_len: length of private data
4791 * @ops: callbacks for this device
4792 * @requested_name: Requested name for this device.
4793 * NULL is valid value, and means use the default naming (phy%d)
4794 *
4795 * Return: A pointer to the new hardware device, or %NULL on error.
4796 */
4797struct ieee80211_hw *ieee80211_alloc_hw_nm(size_t priv_data_len,
4798 const struct ieee80211_ops *ops,
4799 const char *requested_name);
4800
4801/**
4802 * ieee80211_alloc_hw - Allocate a new hardware device
4803 *
4804 * This must be called once for each hardware device. The returned pointer
4805 * must be used to refer to this device when calling other functions.
4806 * mac80211 allocates a private data area for the driver pointed to by
4807 * @priv in &struct ieee80211_hw, the size of this area is given as
4808 * @priv_data_len.
4809 *
4810 * @priv_data_len: length of private data
4811 * @ops: callbacks for this device
4812 *
4813 * Return: A pointer to the new hardware device, or %NULL on error.
4814 */
4815static inline
4816struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len,
4817 const struct ieee80211_ops *ops)
4818{
4819 return ieee80211_alloc_hw_nm(priv_data_len, ops, NULL);
4820}
4821
4822/**
4823 * ieee80211_register_hw - Register hardware device
4824 *
4825 * You must call this function before any other functions in
4826 * mac80211. Note that before a hardware can be registered, you
4827 * need to fill the contained wiphy's information.
4828 *
4829 * @hw: the device to register as returned by ieee80211_alloc_hw()
4830 *
4831 * Return: 0 on success. An error code otherwise.
4832 */
4833int ieee80211_register_hw(struct ieee80211_hw *hw);
4834
4835/**
4836 * struct ieee80211_tpt_blink - throughput blink description
4837 * @throughput: throughput in Kbit/sec
4838 * @blink_time: blink time in milliseconds
4839 * (full cycle, ie. one off + one on period)
4840 */
4841struct ieee80211_tpt_blink {
4842 int throughput;
4843 int blink_time;
4844};
4845
4846/**
4847 * enum ieee80211_tpt_led_trigger_flags - throughput trigger flags
4848 * @IEEE80211_TPT_LEDTRIG_FL_RADIO: enable blinking with radio
4849 * @IEEE80211_TPT_LEDTRIG_FL_WORK: enable blinking when working
4850 * @IEEE80211_TPT_LEDTRIG_FL_CONNECTED: enable blinking when at least one
4851 * interface is connected in some way, including being an AP
4852 */
4853enum ieee80211_tpt_led_trigger_flags {
4854 IEEE80211_TPT_LEDTRIG_FL_RADIO = BIT(0),
4855 IEEE80211_TPT_LEDTRIG_FL_WORK = BIT(1),
4856 IEEE80211_TPT_LEDTRIG_FL_CONNECTED = BIT(2),
4857};
4858
4859#ifdef CONFIG_MAC80211_LEDS
4860const char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
4861const char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
4862const char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
4863const char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
4864const char *
4865__ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw,
4866 unsigned int flags,
4867 const struct ieee80211_tpt_blink *blink_table,
4868 unsigned int blink_table_len);
4869#endif
4870/**
4871 * ieee80211_get_tx_led_name - get name of TX LED
4872 *
4873 * mac80211 creates a transmit LED trigger for each wireless hardware
4874 * that can be used to drive LEDs if your driver registers a LED device.
4875 * This function returns the name (or %NULL if not configured for LEDs)
4876 * of the trigger so you can automatically link the LED device.
4877 *
4878 * @hw: the hardware to get the LED trigger name for
4879 *
4880 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
4881 */
4882static inline const char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw)
4883{
4884#ifdef CONFIG_MAC80211_LEDS
4885 return __ieee80211_get_tx_led_name(hw);
4886#else
4887 return NULL;
4888#endif
4889}
4890
4891/**
4892 * ieee80211_get_rx_led_name - get name of RX LED
4893 *
4894 * mac80211 creates a receive LED trigger for each wireless hardware
4895 * that can be used to drive LEDs if your driver registers a LED device.
4896 * This function returns the name (or %NULL if not configured for LEDs)
4897 * of the trigger so you can automatically link the LED device.
4898 *
4899 * @hw: the hardware to get the LED trigger name for
4900 *
4901 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
4902 */
4903static inline const char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw)
4904{
4905#ifdef CONFIG_MAC80211_LEDS
4906 return __ieee80211_get_rx_led_name(hw);
4907#else
4908 return NULL;
4909#endif
4910}
4911
4912/**
4913 * ieee80211_get_assoc_led_name - get name of association LED
4914 *
4915 * mac80211 creates a association LED trigger for each wireless hardware
4916 * that can be used to drive LEDs if your driver registers a LED device.
4917 * This function returns the name (or %NULL if not configured for LEDs)
4918 * of the trigger so you can automatically link the LED device.
4919 *
4920 * @hw: the hardware to get the LED trigger name for
4921 *
4922 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
4923 */
4924static inline const char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
4925{
4926#ifdef CONFIG_MAC80211_LEDS
4927 return __ieee80211_get_assoc_led_name(hw);
4928#else
4929 return NULL;
4930#endif
4931}
4932
4933/**
4934 * ieee80211_get_radio_led_name - get name of radio LED
4935 *
4936 * mac80211 creates a radio change LED trigger for each wireless hardware
4937 * that can be used to drive LEDs if your driver registers a LED device.
4938 * This function returns the name (or %NULL if not configured for LEDs)
4939 * of the trigger so you can automatically link the LED device.
4940 *
4941 * @hw: the hardware to get the LED trigger name for
4942 *
4943 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
4944 */
4945static inline const char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw)
4946{
4947#ifdef CONFIG_MAC80211_LEDS
4948 return __ieee80211_get_radio_led_name(hw);
4949#else
4950 return NULL;
4951#endif
4952}
4953
4954/**
4955 * ieee80211_create_tpt_led_trigger - create throughput LED trigger
4956 * @hw: the hardware to create the trigger for
4957 * @flags: trigger flags, see &enum ieee80211_tpt_led_trigger_flags
4958 * @blink_table: the blink table -- needs to be ordered by throughput
4959 * @blink_table_len: size of the blink table
4960 *
4961 * Return: %NULL (in case of error, or if no LED triggers are
4962 * configured) or the name of the new trigger.
4963 *
4964 * Note: This function must be called before ieee80211_register_hw().
4965 */
4966static inline const char *
4967ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, unsigned int flags,
4968 const struct ieee80211_tpt_blink *blink_table,
4969 unsigned int blink_table_len)
4970{
4971#ifdef CONFIG_MAC80211_LEDS
4972 return __ieee80211_create_tpt_led_trigger(hw, flags, blink_table,
4973 blink_table_len);
4974#else
4975 return NULL;
4976#endif
4977}
4978
4979/**
4980 * ieee80211_unregister_hw - Unregister a hardware device
4981 *
4982 * This function instructs mac80211 to free allocated resources
4983 * and unregister netdevices from the networking subsystem.
4984 *
4985 * @hw: the hardware to unregister
4986 */
4987void ieee80211_unregister_hw(struct ieee80211_hw *hw);
4988
4989/**
4990 * ieee80211_free_hw - free hardware descriptor
4991 *
4992 * This function frees everything that was allocated, including the
4993 * private data for the driver. You must call ieee80211_unregister_hw()
4994 * before calling this function.
4995 *
4996 * @hw: the hardware to free
4997 */
4998void ieee80211_free_hw(struct ieee80211_hw *hw);
4999
5000/**
5001 * ieee80211_restart_hw - restart hardware completely
5002 *
5003 * Call this function when the hardware was restarted for some reason
5004 * (hardware error, ...) and the driver is unable to restore its state
5005 * by itself. mac80211 assumes that at this point the driver/hardware
5006 * is completely uninitialised and stopped, it starts the process by
5007 * calling the ->start() operation. The driver will need to reset all
5008 * internal state that it has prior to calling this function.
5009 *
5010 * @hw: the hardware to restart
5011 */
5012void ieee80211_restart_hw(struct ieee80211_hw *hw);
5013
5014/**
5015 * ieee80211_rx_list - receive frame and store processed skbs in a list
5016 *
5017 * Use this function to hand received frames to mac80211. The receive
5018 * buffer in @skb must start with an IEEE 802.11 header. In case of a
5019 * paged @skb is used, the driver is recommended to put the ieee80211
5020 * header of the frame on the linear part of the @skb to avoid memory
5021 * allocation and/or memcpy by the stack.
5022 *
5023 * This function may not be called in IRQ context. Calls to this function
5024 * for a single hardware must be synchronized against each other. Calls to
5025 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
5026 * mixed for a single hardware. Must not run concurrently with
5027 * ieee80211_tx_status_skb() or ieee80211_tx_status_ni().
5028 *
5029 * This function must be called with BHs disabled and RCU read lock
5030 *
5031 * @hw: the hardware this frame came in on
5032 * @sta: the station the frame was received from, or %NULL
5033 * @skb: the buffer to receive, owned by mac80211 after this call
5034 * @list: the destination list
5035 */
5036void ieee80211_rx_list(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
5037 struct sk_buff *skb, struct list_head *list);
5038
5039/**
5040 * ieee80211_rx_napi - receive frame from NAPI context
5041 *
5042 * Use this function to hand received frames to mac80211. The receive
5043 * buffer in @skb must start with an IEEE 802.11 header. In case of a
5044 * paged @skb is used, the driver is recommended to put the ieee80211
5045 * header of the frame on the linear part of the @skb to avoid memory
5046 * allocation and/or memcpy by the stack.
5047 *
5048 * This function may not be called in IRQ context. Calls to this function
5049 * for a single hardware must be synchronized against each other. Calls to
5050 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
5051 * mixed for a single hardware. Must not run concurrently with
5052 * ieee80211_tx_status_skb() or ieee80211_tx_status_ni().
5053 *
5054 * This function must be called with BHs disabled.
5055 *
5056 * @hw: the hardware this frame came in on
5057 * @sta: the station the frame was received from, or %NULL
5058 * @skb: the buffer to receive, owned by mac80211 after this call
5059 * @napi: the NAPI context
5060 */
5061void ieee80211_rx_napi(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
5062 struct sk_buff *skb, struct napi_struct *napi);
5063
5064/**
5065 * ieee80211_rx - receive frame
5066 *
5067 * Use this function to hand received frames to mac80211. The receive
5068 * buffer in @skb must start with an IEEE 802.11 header. In case of a
5069 * paged @skb is used, the driver is recommended to put the ieee80211
5070 * header of the frame on the linear part of the @skb to avoid memory
5071 * allocation and/or memcpy by the stack.
5072 *
5073 * This function may not be called in IRQ context. Calls to this function
5074 * for a single hardware must be synchronized against each other. Calls to
5075 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
5076 * mixed for a single hardware. Must not run concurrently with
5077 * ieee80211_tx_status_skb() or ieee80211_tx_status_ni().
5078 *
5079 * In process context use instead ieee80211_rx_ni().
5080 *
5081 * @hw: the hardware this frame came in on
5082 * @skb: the buffer to receive, owned by mac80211 after this call
5083 */
5084static inline void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb)
5085{
5086 ieee80211_rx_napi(hw, NULL, skb, NULL);
5087}
5088
5089/**
5090 * ieee80211_rx_irqsafe - receive frame
5091 *
5092 * Like ieee80211_rx() but can be called in IRQ context
5093 * (internally defers to a tasklet.)
5094 *
5095 * Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not
5096 * be mixed for a single hardware.Must not run concurrently with
5097 * ieee80211_tx_status_skb() or ieee80211_tx_status_ni().
5098 *
5099 * @hw: the hardware this frame came in on
5100 * @skb: the buffer to receive, owned by mac80211 after this call
5101 */
5102void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb);
5103
5104/**
5105 * ieee80211_rx_ni - receive frame (in process context)
5106 *
5107 * Like ieee80211_rx() but can be called in process context
5108 * (internally disables bottom halves).
5109 *
5110 * Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may
5111 * not be mixed for a single hardware. Must not run concurrently with
5112 * ieee80211_tx_status_skb() or ieee80211_tx_status_ni().
5113 *
5114 * @hw: the hardware this frame came in on
5115 * @skb: the buffer to receive, owned by mac80211 after this call
5116 */
5117static inline void ieee80211_rx_ni(struct ieee80211_hw *hw,
5118 struct sk_buff *skb)
5119{
5120 local_bh_disable();
5121 ieee80211_rx(hw, skb);
5122 local_bh_enable();
5123}
5124
5125/**
5126 * ieee80211_sta_ps_transition - PS transition for connected sta
5127 *
5128 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS
5129 * flag set, use this function to inform mac80211 about a connected station
5130 * entering/leaving PS mode.
5131 *
5132 * This function may not be called in IRQ context or with softirqs enabled.
5133 *
5134 * Calls to this function for a single hardware must be synchronized against
5135 * each other.
5136 *
5137 * @sta: currently connected sta
5138 * @start: start or stop PS
5139 *
5140 * Return: 0 on success. -EINVAL when the requested PS mode is already set.
5141 */
5142int ieee80211_sta_ps_transition(struct ieee80211_sta *sta, bool start);
5143
5144/**
5145 * ieee80211_sta_ps_transition_ni - PS transition for connected sta
5146 * (in process context)
5147 *
5148 * Like ieee80211_sta_ps_transition() but can be called in process context
5149 * (internally disables bottom halves). Concurrent call restriction still
5150 * applies.
5151 *
5152 * @sta: currently connected sta
5153 * @start: start or stop PS
5154 *
5155 * Return: Like ieee80211_sta_ps_transition().
5156 */
5157static inline int ieee80211_sta_ps_transition_ni(struct ieee80211_sta *sta,
5158 bool start)
5159{
5160 int ret;
5161
5162 local_bh_disable();
5163 ret = ieee80211_sta_ps_transition(sta, start);
5164 local_bh_enable();
5165
5166 return ret;
5167}
5168
5169/**
5170 * ieee80211_sta_pspoll - PS-Poll frame received
5171 * @sta: currently connected station
5172 *
5173 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS flag set,
5174 * use this function to inform mac80211 that a PS-Poll frame from a
5175 * connected station was received.
5176 * This must be used in conjunction with ieee80211_sta_ps_transition()
5177 * and possibly ieee80211_sta_uapsd_trigger(); calls to all three must
5178 * be serialized.
5179 */
5180void ieee80211_sta_pspoll(struct ieee80211_sta *sta);
5181
5182/**
5183 * ieee80211_sta_uapsd_trigger - (potential) U-APSD trigger frame received
5184 * @sta: currently connected station
5185 * @tid: TID of the received (potential) trigger frame
5186 *
5187 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS flag set,
5188 * use this function to inform mac80211 that a (potential) trigger frame
5189 * from a connected station was received.
5190 * This must be used in conjunction with ieee80211_sta_ps_transition()
5191 * and possibly ieee80211_sta_pspoll(); calls to all three must be
5192 * serialized.
5193 * %IEEE80211_NUM_TIDS can be passed as the tid if the tid is unknown.
5194 * In this case, mac80211 will not check that this tid maps to an AC
5195 * that is trigger enabled and assume that the caller did the proper
5196 * checks.
5197 */
5198void ieee80211_sta_uapsd_trigger(struct ieee80211_sta *sta, u8 tid);
5199
5200/*
5201 * The TX headroom reserved by mac80211 for its own tx_status functions.
5202 * This is enough for the radiotap header.
5203 */
5204#define IEEE80211_TX_STATUS_HEADROOM ALIGN(14, 4)
5205
5206/**
5207 * ieee80211_sta_set_buffered - inform mac80211 about driver-buffered frames
5208 * @sta: &struct ieee80211_sta pointer for the sleeping station
5209 * @tid: the TID that has buffered frames
5210 * @buffered: indicates whether or not frames are buffered for this TID
5211 *
5212 * If a driver buffers frames for a powersave station instead of passing
5213 * them back to mac80211 for retransmission, the station may still need
5214 * to be told that there are buffered frames via the TIM bit.
5215 *
5216 * This function informs mac80211 whether or not there are frames that are
5217 * buffered in the driver for a given TID; mac80211 can then use this data
5218 * to set the TIM bit (NOTE: This may call back into the driver's set_tim
5219 * call! Beware of the locking!)
5220 *
5221 * If all frames are released to the station (due to PS-poll or uAPSD)
5222 * then the driver needs to inform mac80211 that there no longer are
5223 * frames buffered. However, when the station wakes up mac80211 assumes
5224 * that all buffered frames will be transmitted and clears this data,
5225 * drivers need to make sure they inform mac80211 about all buffered
5226 * frames on the sleep transition (sta_notify() with %STA_NOTIFY_SLEEP).
5227 *
5228 * Note that technically mac80211 only needs to know this per AC, not per
5229 * TID, but since driver buffering will inevitably happen per TID (since
5230 * it is related to aggregation) it is easier to make mac80211 map the
5231 * TID to the AC as required instead of keeping track in all drivers that
5232 * use this API.
5233 */
5234void ieee80211_sta_set_buffered(struct ieee80211_sta *sta,
5235 u8 tid, bool buffered);
5236
5237/**
5238 * ieee80211_get_tx_rates - get the selected transmit rates for a packet
5239 *
5240 * Call this function in a driver with per-packet rate selection support
5241 * to combine the rate info in the packet tx info with the most recent
5242 * rate selection table for the station entry.
5243 *
5244 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5245 * @sta: the receiver station to which this packet is sent.
5246 * @skb: the frame to be transmitted.
5247 * @dest: buffer for extracted rate/retry information
5248 * @max_rates: maximum number of rates to fetch
5249 */
5250void ieee80211_get_tx_rates(struct ieee80211_vif *vif,
5251 struct ieee80211_sta *sta,
5252 struct sk_buff *skb,
5253 struct ieee80211_tx_rate *dest,
5254 int max_rates);
5255
5256/**
5257 * ieee80211_sta_set_expected_throughput - set the expected tpt for a station
5258 *
5259 * Call this function to notify mac80211 about a change in expected throughput
5260 * to a station. A driver for a device that does rate control in firmware can
5261 * call this function when the expected throughput estimate towards a station
5262 * changes. The information is used to tune the CoDel AQM applied to traffic
5263 * going towards that station (which can otherwise be too aggressive and cause
5264 * slow stations to starve).
5265 *
5266 * @pubsta: the station to set throughput for.
5267 * @thr: the current expected throughput in kbps.
5268 */
5269void ieee80211_sta_set_expected_throughput(struct ieee80211_sta *pubsta,
5270 u32 thr);
5271
5272/**
5273 * ieee80211_tx_rate_update - transmit rate update callback
5274 *
5275 * Drivers should call this functions with a non-NULL pub sta
5276 * This function can be used in drivers that does not have provision
5277 * in updating the tx rate in data path.
5278 *
5279 * @hw: the hardware the frame was transmitted by
5280 * @pubsta: the station to update the tx rate for.
5281 * @info: tx status information
5282 */
5283void ieee80211_tx_rate_update(struct ieee80211_hw *hw,
5284 struct ieee80211_sta *pubsta,
5285 struct ieee80211_tx_info *info);
5286
5287/**
5288 * ieee80211_tx_status_skb - transmit status callback
5289 *
5290 * Call this function for all transmitted frames after they have been
5291 * transmitted. It is permissible to not call this function for
5292 * multicast frames but this can affect statistics.
5293 *
5294 * This function may not be called in IRQ context. Calls to this function
5295 * for a single hardware must be synchronized against each other. Calls
5296 * to this function, ieee80211_tx_status_ni() and ieee80211_tx_status_irqsafe()
5297 * may not be mixed for a single hardware. Must not run concurrently with
5298 * ieee80211_rx() or ieee80211_rx_ni().
5299 *
5300 * @hw: the hardware the frame was transmitted by
5301 * @skb: the frame that was transmitted, owned by mac80211 after this call
5302 */
5303void ieee80211_tx_status_skb(struct ieee80211_hw *hw,
5304 struct sk_buff *skb);
5305
5306/**
5307 * ieee80211_tx_status_ext - extended transmit status callback
5308 *
5309 * This function can be used as a replacement for ieee80211_tx_status_skb()
5310 * in drivers that may want to provide extra information that does not
5311 * fit into &struct ieee80211_tx_info.
5312 *
5313 * Calls to this function for a single hardware must be synchronized
5314 * against each other. Calls to this function, ieee80211_tx_status_ni()
5315 * and ieee80211_tx_status_irqsafe() may not be mixed for a single hardware.
5316 *
5317 * @hw: the hardware the frame was transmitted by
5318 * @status: tx status information
5319 */
5320void ieee80211_tx_status_ext(struct ieee80211_hw *hw,
5321 struct ieee80211_tx_status *status);
5322
5323/**
5324 * ieee80211_tx_status_noskb - transmit status callback without skb
5325 *
5326 * This function can be used as a replacement for ieee80211_tx_status_skb()
5327 * in drivers that cannot reliably map tx status information back to
5328 * specific skbs.
5329 *
5330 * Calls to this function for a single hardware must be synchronized
5331 * against each other. Calls to this function, ieee80211_tx_status_ni()
5332 * and ieee80211_tx_status_irqsafe() may not be mixed for a single hardware.
5333 *
5334 * @hw: the hardware the frame was transmitted by
5335 * @sta: the receiver station to which this packet is sent
5336 * (NULL for multicast packets)
5337 * @info: tx status information
5338 */
5339static inline void ieee80211_tx_status_noskb(struct ieee80211_hw *hw,
5340 struct ieee80211_sta *sta,
5341 struct ieee80211_tx_info *info)
5342{
5343 struct ieee80211_tx_status status = {
5344 .sta = sta,
5345 .info = info,
5346 };
5347
5348 ieee80211_tx_status_ext(hw, &status);
5349}
5350
5351/**
5352 * ieee80211_tx_status_ni - transmit status callback (in process context)
5353 *
5354 * Like ieee80211_tx_status_skb() but can be called in process context.
5355 *
5356 * Calls to this function, ieee80211_tx_status_skb() and
5357 * ieee80211_tx_status_irqsafe() may not be mixed
5358 * for a single hardware.
5359 *
5360 * @hw: the hardware the frame was transmitted by
5361 * @skb: the frame that was transmitted, owned by mac80211 after this call
5362 */
5363static inline void ieee80211_tx_status_ni(struct ieee80211_hw *hw,
5364 struct sk_buff *skb)
5365{
5366 local_bh_disable();
5367 ieee80211_tx_status_skb(hw, skb);
5368 local_bh_enable();
5369}
5370
5371/**
5372 * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback
5373 *
5374 * Like ieee80211_tx_status_skb() but can be called in IRQ context
5375 * (internally defers to a tasklet.)
5376 *
5377 * Calls to this function, ieee80211_tx_status_skb() and
5378 * ieee80211_tx_status_ni() may not be mixed for a single hardware.
5379 *
5380 * @hw: the hardware the frame was transmitted by
5381 * @skb: the frame that was transmitted, owned by mac80211 after this call
5382 */
5383void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
5384 struct sk_buff *skb);
5385
5386/**
5387 * ieee80211_report_low_ack - report non-responding station
5388 *
5389 * When operating in AP-mode, call this function to report a non-responding
5390 * connected STA.
5391 *
5392 * @sta: the non-responding connected sta
5393 * @num_packets: number of packets sent to @sta without a response
5394 */
5395void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets);
5396
5397#define IEEE80211_MAX_CNTDWN_COUNTERS_NUM 2
5398
5399/**
5400 * struct ieee80211_mutable_offsets - mutable beacon offsets
5401 * @tim_offset: position of TIM element
5402 * @tim_length: size of TIM element
5403 * @cntdwn_counter_offs: array of IEEE80211_MAX_CNTDWN_COUNTERS_NUM offsets
5404 * to countdown counters. This array can contain zero values which
5405 * should be ignored.
5406 * @mbssid_off: position of the multiple bssid element
5407 */
5408struct ieee80211_mutable_offsets {
5409 u16 tim_offset;
5410 u16 tim_length;
5411
5412 u16 cntdwn_counter_offs[IEEE80211_MAX_CNTDWN_COUNTERS_NUM];
5413 u16 mbssid_off;
5414};
5415
5416/**
5417 * ieee80211_beacon_get_template - beacon template generation function
5418 * @hw: pointer obtained from ieee80211_alloc_hw().
5419 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5420 * @offs: &struct ieee80211_mutable_offsets pointer to struct that will
5421 * receive the offsets that may be updated by the driver.
5422 * @link_id: the link id to which the beacon belongs (or 0 for an AP STA
5423 * that is not associated with AP MLD).
5424 *
5425 * If the driver implements beaconing modes, it must use this function to
5426 * obtain the beacon template.
5427 *
5428 * This function should be used if the beacon frames are generated by the
5429 * device, and then the driver must use the returned beacon as the template
5430 * The driver or the device are responsible to update the DTIM and, when
5431 * applicable, the CSA count.
5432 *
5433 * The driver is responsible for freeing the returned skb.
5434 *
5435 * Return: The beacon template. %NULL on error.
5436 */
5437struct sk_buff *
5438ieee80211_beacon_get_template(struct ieee80211_hw *hw,
5439 struct ieee80211_vif *vif,
5440 struct ieee80211_mutable_offsets *offs,
5441 unsigned int link_id);
5442
5443/**
5444 * ieee80211_beacon_get_template_ema_index - EMA beacon template generation
5445 * @hw: pointer obtained from ieee80211_alloc_hw().
5446 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5447 * @offs: &struct ieee80211_mutable_offsets pointer to struct that will
5448 * receive the offsets that may be updated by the driver.
5449 * @link_id: the link id to which the beacon belongs (or 0 for a non-MLD AP).
5450 * @ema_index: index of the beacon in the EMA set.
5451 *
5452 * This function follows the same rules as ieee80211_beacon_get_template()
5453 * but returns a beacon template which includes multiple BSSID element at the
5454 * requested index.
5455 *
5456 * Return: The beacon template. %NULL indicates the end of EMA templates.
5457 */
5458struct sk_buff *
5459ieee80211_beacon_get_template_ema_index(struct ieee80211_hw *hw,
5460 struct ieee80211_vif *vif,
5461 struct ieee80211_mutable_offsets *offs,
5462 unsigned int link_id, u8 ema_index);
5463
5464/**
5465 * struct ieee80211_ema_beacons - List of EMA beacons
5466 * @cnt: count of EMA beacons.
5467 *
5468 * @bcn: array of EMA beacons.
5469 * @bcn.skb: the skb containing this specific beacon
5470 * @bcn.offs: &struct ieee80211_mutable_offsets pointer to struct that will
5471 * receive the offsets that may be updated by the driver.
5472 */
5473struct ieee80211_ema_beacons {
5474 u8 cnt;
5475 struct {
5476 struct sk_buff *skb;
5477 struct ieee80211_mutable_offsets offs;
5478 } bcn[];
5479};
5480
5481/**
5482 * ieee80211_beacon_get_template_ema_list - EMA beacon template generation
5483 * @hw: pointer obtained from ieee80211_alloc_hw().
5484 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5485 * @link_id: the link id to which the beacon belongs (or 0 for a non-MLD AP)
5486 *
5487 * This function follows the same rules as ieee80211_beacon_get_template()
5488 * but allocates and returns a pointer to list of all beacon templates required
5489 * to cover all profiles in the multiple BSSID set. Each template includes only
5490 * one multiple BSSID element.
5491 *
5492 * Driver must call ieee80211_beacon_free_ema_list() to free the memory.
5493 *
5494 * Return: EMA beacon templates of type struct ieee80211_ema_beacons *.
5495 * %NULL on error.
5496 */
5497struct ieee80211_ema_beacons *
5498ieee80211_beacon_get_template_ema_list(struct ieee80211_hw *hw,
5499 struct ieee80211_vif *vif,
5500 unsigned int link_id);
5501
5502/**
5503 * ieee80211_beacon_free_ema_list - free an EMA beacon template list
5504 * @ema_beacons: list of EMA beacons of type &struct ieee80211_ema_beacons pointers.
5505 *
5506 * This function will free a list previously acquired by calling
5507 * ieee80211_beacon_get_template_ema_list()
5508 */
5509void ieee80211_beacon_free_ema_list(struct ieee80211_ema_beacons *ema_beacons);
5510
5511/**
5512 * ieee80211_beacon_get_tim - beacon generation function
5513 * @hw: pointer obtained from ieee80211_alloc_hw().
5514 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5515 * @tim_offset: pointer to variable that will receive the TIM IE offset.
5516 * Set to 0 if invalid (in non-AP modes).
5517 * @tim_length: pointer to variable that will receive the TIM IE length,
5518 * (including the ID and length bytes!).
5519 * Set to 0 if invalid (in non-AP modes).
5520 * @link_id: the link id to which the beacon belongs (or 0 for an AP STA
5521 * that is not associated with AP MLD).
5522 *
5523 * If the driver implements beaconing modes, it must use this function to
5524 * obtain the beacon frame.
5525 *
5526 * If the beacon frames are generated by the host system (i.e., not in
5527 * hardware/firmware), the driver uses this function to get each beacon
5528 * frame from mac80211 -- it is responsible for calling this function exactly
5529 * once before the beacon is needed (e.g. based on hardware interrupt).
5530 *
5531 * The driver is responsible for freeing the returned skb.
5532 *
5533 * Return: The beacon template. %NULL on error.
5534 */
5535struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw,
5536 struct ieee80211_vif *vif,
5537 u16 *tim_offset, u16 *tim_length,
5538 unsigned int link_id);
5539
5540/**
5541 * ieee80211_beacon_get - beacon generation function
5542 * @hw: pointer obtained from ieee80211_alloc_hw().
5543 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5544 * @link_id: the link id to which the beacon belongs (or 0 for an AP STA
5545 * that is not associated with AP MLD).
5546 *
5547 * See ieee80211_beacon_get_tim().
5548 *
5549 * Return: See ieee80211_beacon_get_tim().
5550 */
5551static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
5552 struct ieee80211_vif *vif,
5553 unsigned int link_id)
5554{
5555 return ieee80211_beacon_get_tim(hw, vif, NULL, NULL, link_id);
5556}
5557
5558/**
5559 * ieee80211_beacon_update_cntdwn - request mac80211 to decrement the beacon countdown
5560 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5561 * @link_id: valid link_id during MLO or 0 for non-MLO
5562 *
5563 * The beacon counter should be updated after each beacon transmission.
5564 * This function is called implicitly when
5565 * ieee80211_beacon_get/ieee80211_beacon_get_tim are called, however if the
5566 * beacon frames are generated by the device, the driver should call this
5567 * function after each beacon transmission to sync mac80211's beacon countdown.
5568 *
5569 * Return: new countdown value
5570 */
5571u8 ieee80211_beacon_update_cntdwn(struct ieee80211_vif *vif,
5572 unsigned int link_id);
5573
5574/**
5575 * ieee80211_beacon_set_cntdwn - request mac80211 to set beacon countdown
5576 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5577 * @counter: the new value for the counter
5578 *
5579 * The beacon countdown can be changed by the device, this API should be
5580 * used by the device driver to update csa counter in mac80211.
5581 *
5582 * It should never be used together with ieee80211_beacon_update_cntdwn(),
5583 * as it will cause a race condition around the counter value.
5584 */
5585void ieee80211_beacon_set_cntdwn(struct ieee80211_vif *vif, u8 counter);
5586
5587/**
5588 * ieee80211_csa_finish - notify mac80211 about channel switch
5589 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5590 * @link_id: valid link_id during MLO or 0 for non-MLO
5591 *
5592 * After a channel switch announcement was scheduled and the counter in this
5593 * announcement hits 1, this function must be called by the driver to
5594 * notify mac80211 that the channel can be changed.
5595 */
5596void ieee80211_csa_finish(struct ieee80211_vif *vif, unsigned int link_id);
5597
5598/**
5599 * ieee80211_beacon_cntdwn_is_complete - find out if countdown reached 1
5600 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5601 * @link_id: valid link_id during MLO or 0 for non-MLO
5602 *
5603 * This function returns whether the countdown reached zero.
5604 */
5605bool ieee80211_beacon_cntdwn_is_complete(struct ieee80211_vif *vif,
5606 unsigned int link_id);
5607
5608/**
5609 * ieee80211_color_change_finish - notify mac80211 about color change
5610 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5611 *
5612 * After a color change announcement was scheduled and the counter in this
5613 * announcement hits 1, this function must be called by the driver to
5614 * notify mac80211 that the color can be changed
5615 */
5616void ieee80211_color_change_finish(struct ieee80211_vif *vif);
5617
5618/**
5619 * ieee80211_proberesp_get - retrieve a Probe Response template
5620 * @hw: pointer obtained from ieee80211_alloc_hw().
5621 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5622 *
5623 * Creates a Probe Response template which can, for example, be uploaded to
5624 * hardware. The destination address should be set by the caller.
5625 *
5626 * Can only be called in AP mode.
5627 *
5628 * Return: The Probe Response template. %NULL on error.
5629 */
5630struct sk_buff *ieee80211_proberesp_get(struct ieee80211_hw *hw,
5631 struct ieee80211_vif *vif);
5632
5633/**
5634 * ieee80211_pspoll_get - retrieve a PS Poll template
5635 * @hw: pointer obtained from ieee80211_alloc_hw().
5636 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5637 *
5638 * Creates a PS Poll a template which can, for example, uploaded to
5639 * hardware. The template must be updated after association so that correct
5640 * AID, BSSID and MAC address is used.
5641 *
5642 * Note: Caller (or hardware) is responsible for setting the
5643 * &IEEE80211_FCTL_PM bit.
5644 *
5645 * Return: The PS Poll template. %NULL on error.
5646 */
5647struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw,
5648 struct ieee80211_vif *vif);
5649
5650/**
5651 * ieee80211_nullfunc_get - retrieve a nullfunc template
5652 * @hw: pointer obtained from ieee80211_alloc_hw().
5653 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5654 * @link_id: If the vif is an MLD, get a frame with the link addresses
5655 * for the given link ID. For a link_id < 0 you get a frame with
5656 * MLD addresses, however useful that might be.
5657 * @qos_ok: QoS NDP is acceptable to the caller, this should be set
5658 * if at all possible
5659 *
5660 * Creates a Nullfunc template which can, for example, uploaded to
5661 * hardware. The template must be updated after association so that correct
5662 * BSSID and address is used.
5663 *
5664 * If @qos_ndp is set and the association is to an AP with QoS/WMM, the
5665 * returned packet will be QoS NDP.
5666 *
5667 * Note: Caller (or hardware) is responsible for setting the
5668 * &IEEE80211_FCTL_PM bit as well as Duration and Sequence Control fields.
5669 *
5670 * Return: The nullfunc template. %NULL on error.
5671 */
5672struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw,
5673 struct ieee80211_vif *vif,
5674 int link_id, bool qos_ok);
5675
5676/**
5677 * ieee80211_probereq_get - retrieve a Probe Request template
5678 * @hw: pointer obtained from ieee80211_alloc_hw().
5679 * @src_addr: source MAC address
5680 * @ssid: SSID buffer
5681 * @ssid_len: length of SSID
5682 * @tailroom: tailroom to reserve at end of SKB for IEs
5683 *
5684 * Creates a Probe Request template which can, for example, be uploaded to
5685 * hardware.
5686 *
5687 * Return: The Probe Request template. %NULL on error.
5688 */
5689struct sk_buff *ieee80211_probereq_get(struct ieee80211_hw *hw,
5690 const u8 *src_addr,
5691 const u8 *ssid, size_t ssid_len,
5692 size_t tailroom);
5693
5694/**
5695 * ieee80211_rts_get - RTS frame generation function
5696 * @hw: pointer obtained from ieee80211_alloc_hw().
5697 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5698 * @frame: pointer to the frame that is going to be protected by the RTS.
5699 * @frame_len: the frame length (in octets).
5700 * @frame_txctl: &struct ieee80211_tx_info of the frame.
5701 * @rts: The buffer where to store the RTS frame.
5702 *
5703 * If the RTS frames are generated by the host system (i.e., not in
5704 * hardware/firmware), the low-level driver uses this function to receive
5705 * the next RTS frame from the 802.11 code. The low-level is responsible
5706 * for calling this function before and RTS frame is needed.
5707 */
5708void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
5709 const void *frame, size_t frame_len,
5710 const struct ieee80211_tx_info *frame_txctl,
5711 struct ieee80211_rts *rts);
5712
5713/**
5714 * ieee80211_rts_duration - Get the duration field for an RTS frame
5715 * @hw: pointer obtained from ieee80211_alloc_hw().
5716 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5717 * @frame_len: the length of the frame that is going to be protected by the RTS.
5718 * @frame_txctl: &struct ieee80211_tx_info of the frame.
5719 *
5720 * If the RTS is generated in firmware, but the host system must provide
5721 * the duration field, the low-level driver uses this function to receive
5722 * the duration field value in little-endian byteorder.
5723 *
5724 * Return: The duration.
5725 */
5726__le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
5727 struct ieee80211_vif *vif, size_t frame_len,
5728 const struct ieee80211_tx_info *frame_txctl);
5729
5730/**
5731 * ieee80211_ctstoself_get - CTS-to-self frame generation function
5732 * @hw: pointer obtained from ieee80211_alloc_hw().
5733 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5734 * @frame: pointer to the frame that is going to be protected by the CTS-to-self.
5735 * @frame_len: the frame length (in octets).
5736 * @frame_txctl: &struct ieee80211_tx_info of the frame.
5737 * @cts: The buffer where to store the CTS-to-self frame.
5738 *
5739 * If the CTS-to-self frames are generated by the host system (i.e., not in
5740 * hardware/firmware), the low-level driver uses this function to receive
5741 * the next CTS-to-self frame from the 802.11 code. The low-level is responsible
5742 * for calling this function before and CTS-to-self frame is needed.
5743 */
5744void ieee80211_ctstoself_get(struct ieee80211_hw *hw,
5745 struct ieee80211_vif *vif,
5746 const void *frame, size_t frame_len,
5747 const struct ieee80211_tx_info *frame_txctl,
5748 struct ieee80211_cts *cts);
5749
5750/**
5751 * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
5752 * @hw: pointer obtained from ieee80211_alloc_hw().
5753 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5754 * @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
5755 * @frame_txctl: &struct ieee80211_tx_info of the frame.
5756 *
5757 * If the CTS-to-self is generated in firmware, but the host system must provide
5758 * the duration field, the low-level driver uses this function to receive
5759 * the duration field value in little-endian byteorder.
5760 *
5761 * Return: The duration.
5762 */
5763__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
5764 struct ieee80211_vif *vif,
5765 size_t frame_len,
5766 const struct ieee80211_tx_info *frame_txctl);
5767
5768/**
5769 * ieee80211_generic_frame_duration - Calculate the duration field for a frame
5770 * @hw: pointer obtained from ieee80211_alloc_hw().
5771 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5772 * @band: the band to calculate the frame duration on
5773 * @frame_len: the length of the frame.
5774 * @rate: the rate at which the frame is going to be transmitted.
5775 *
5776 * Calculate the duration field of some generic frame, given its
5777 * length and transmission rate (in 100kbps).
5778 *
5779 * Return: The duration.
5780 */
5781__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
5782 struct ieee80211_vif *vif,
5783 enum nl80211_band band,
5784 size_t frame_len,
5785 struct ieee80211_rate *rate);
5786
5787/**
5788 * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
5789 * @hw: pointer as obtained from ieee80211_alloc_hw().
5790 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5791 *
5792 * Function for accessing buffered broadcast and multicast frames. If
5793 * hardware/firmware does not implement buffering of broadcast/multicast
5794 * frames when power saving is used, 802.11 code buffers them in the host
5795 * memory. The low-level driver uses this function to fetch next buffered
5796 * frame. In most cases, this is used when generating beacon frame.
5797 *
5798 * Return: A pointer to the next buffered skb or NULL if no more buffered
5799 * frames are available.
5800 *
5801 * Note: buffered frames are returned only after DTIM beacon frame was
5802 * generated with ieee80211_beacon_get() and the low-level driver must thus
5803 * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns
5804 * NULL if the previous generated beacon was not DTIM, so the low-level driver
5805 * does not need to check for DTIM beacons separately and should be able to
5806 * use common code for all beacons.
5807 */
5808struct sk_buff *
5809ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
5810
5811/**
5812 * ieee80211_get_tkip_p1k_iv - get a TKIP phase 1 key for IV32
5813 *
5814 * This function returns the TKIP phase 1 key for the given IV32.
5815 *
5816 * @keyconf: the parameter passed with the set key
5817 * @iv32: IV32 to get the P1K for
5818 * @p1k: a buffer to which the key will be written, as 5 u16 values
5819 */
5820void ieee80211_get_tkip_p1k_iv(struct ieee80211_key_conf *keyconf,
5821 u32 iv32, u16 *p1k);
5822
5823/**
5824 * ieee80211_get_tkip_p1k - get a TKIP phase 1 key
5825 *
5826 * This function returns the TKIP phase 1 key for the IV32 taken
5827 * from the given packet.
5828 *
5829 * @keyconf: the parameter passed with the set key
5830 * @skb: the packet to take the IV32 value from that will be encrypted
5831 * with this P1K
5832 * @p1k: a buffer to which the key will be written, as 5 u16 values
5833 */
5834static inline void ieee80211_get_tkip_p1k(struct ieee80211_key_conf *keyconf,
5835 struct sk_buff *skb, u16 *p1k)
5836{
5837 struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
5838 const u8 *data = (u8 *)hdr + ieee80211_hdrlen(hdr->frame_control);
5839 u32 iv32 = get_unaligned_le32(&data[4]);
5840
5841 ieee80211_get_tkip_p1k_iv(keyconf, iv32, p1k);
5842}
5843
5844/**
5845 * ieee80211_get_tkip_rx_p1k - get a TKIP phase 1 key for RX
5846 *
5847 * This function returns the TKIP phase 1 key for the given IV32
5848 * and transmitter address.
5849 *
5850 * @keyconf: the parameter passed with the set key
5851 * @ta: TA that will be used with the key
5852 * @iv32: IV32 to get the P1K for
5853 * @p1k: a buffer to which the key will be written, as 5 u16 values
5854 */
5855void ieee80211_get_tkip_rx_p1k(struct ieee80211_key_conf *keyconf,
5856 const u8 *ta, u32 iv32, u16 *p1k);
5857
5858/**
5859 * ieee80211_get_tkip_p2k - get a TKIP phase 2 key
5860 *
5861 * This function computes the TKIP RC4 key for the IV values
5862 * in the packet.
5863 *
5864 * @keyconf: the parameter passed with the set key
5865 * @skb: the packet to take the IV32/IV16 values from that will be
5866 * encrypted with this key
5867 * @p2k: a buffer to which the key will be written, 16 bytes
5868 */
5869void ieee80211_get_tkip_p2k(struct ieee80211_key_conf *keyconf,
5870 struct sk_buff *skb, u8 *p2k);
5871
5872/**
5873 * ieee80211_tkip_add_iv - write TKIP IV and Ext. IV to pos
5874 *
5875 * @pos: start of crypto header
5876 * @keyconf: the parameter passed with the set key
5877 * @pn: PN to add
5878 *
5879 * Returns: pointer to the octet following IVs (i.e. beginning of
5880 * the packet payload)
5881 *
5882 * This function writes the tkip IV value to pos (which should
5883 * point to the crypto header)
5884 */
5885u8 *ieee80211_tkip_add_iv(u8 *pos, struct ieee80211_key_conf *keyconf, u64 pn);
5886
5887/**
5888 * ieee80211_get_key_rx_seq - get key RX sequence counter
5889 *
5890 * @keyconf: the parameter passed with the set key
5891 * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only);
5892 * the value on TID 0 is also used for non-QoS frames. For
5893 * CMAC, only TID 0 is valid.
5894 * @seq: buffer to receive the sequence data
5895 *
5896 * This function allows a driver to retrieve the current RX IV/PNs
5897 * for the given key. It must not be called if IV checking is done
5898 * by the device and not by mac80211.
5899 *
5900 * Note that this function may only be called when no RX processing
5901 * can be done concurrently.
5902 */
5903void ieee80211_get_key_rx_seq(struct ieee80211_key_conf *keyconf,
5904 int tid, struct ieee80211_key_seq *seq);
5905
5906/**
5907 * ieee80211_set_key_rx_seq - set key RX sequence counter
5908 *
5909 * @keyconf: the parameter passed with the set key
5910 * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only);
5911 * the value on TID 0 is also used for non-QoS frames. For
5912 * CMAC, only TID 0 is valid.
5913 * @seq: new sequence data
5914 *
5915 * This function allows a driver to set the current RX IV/PNs for the
5916 * given key. This is useful when resuming from WoWLAN sleep and GTK
5917 * rekey may have been done while suspended. It should not be called
5918 * if IV checking is done by the device and not by mac80211.
5919 *
5920 * Note that this function may only be called when no RX processing
5921 * can be done concurrently.
5922 */
5923void ieee80211_set_key_rx_seq(struct ieee80211_key_conf *keyconf,
5924 int tid, struct ieee80211_key_seq *seq);
5925
5926/**
5927 * ieee80211_remove_key - remove the given key
5928 * @keyconf: the parameter passed with the set key
5929 *
5930 * Context: Must be called with the wiphy mutex held.
5931 *
5932 * Remove the given key. If the key was uploaded to the hardware at the
5933 * time this function is called, it is not deleted in the hardware but
5934 * instead assumed to have been removed already.
5935 */
5936void ieee80211_remove_key(struct ieee80211_key_conf *keyconf);
5937
5938/**
5939 * ieee80211_gtk_rekey_add - add a GTK key from rekeying during WoWLAN
5940 * @vif: the virtual interface to add the key on
5941 * @keyconf: new key data
5942 * @link_id: the link id of the key or -1 for non-MLO
5943 *
5944 * When GTK rekeying was done while the system was suspended, (a) new
5945 * key(s) will be available. These will be needed by mac80211 for proper
5946 * RX processing, so this function allows setting them.
5947 *
5948 * The function returns the newly allocated key structure, which will
5949 * have similar contents to the passed key configuration but point to
5950 * mac80211-owned memory. In case of errors, the function returns an
5951 * ERR_PTR(), use IS_ERR() etc.
5952 *
5953 * Note that this function assumes the key isn't added to hardware
5954 * acceleration, so no TX will be done with the key. Since it's a GTK
5955 * on managed (station) networks, this is true anyway. If the driver
5956 * calls this function from the resume callback and subsequently uses
5957 * the return code 1 to reconfigure the device, this key will be part
5958 * of the reconfiguration.
5959 *
5960 * Note that the driver should also call ieee80211_set_key_rx_seq()
5961 * for the new key for each TID to set up sequence counters properly.
5962 *
5963 * IMPORTANT: If this replaces a key that is present in the hardware,
5964 * then it will attempt to remove it during this call. In many cases
5965 * this isn't what you want, so call ieee80211_remove_key() first for
5966 * the key that's being replaced.
5967 */
5968struct ieee80211_key_conf *
5969ieee80211_gtk_rekey_add(struct ieee80211_vif *vif,
5970 struct ieee80211_key_conf *keyconf,
5971 int link_id);
5972
5973/**
5974 * ieee80211_gtk_rekey_notify - notify userspace supplicant of rekeying
5975 * @vif: virtual interface the rekeying was done on
5976 * @bssid: The BSSID of the AP, for checking association
5977 * @replay_ctr: the new replay counter after GTK rekeying
5978 * @gfp: allocation flags
5979 */
5980void ieee80211_gtk_rekey_notify(struct ieee80211_vif *vif, const u8 *bssid,
5981 const u8 *replay_ctr, gfp_t gfp);
5982
5983/**
5984 * ieee80211_key_mic_failure - increment MIC failure counter for the key
5985 *
5986 * Note: this is really only safe if no other RX function is called
5987 * at the same time.
5988 *
5989 * @keyconf: the key in question
5990 */
5991void ieee80211_key_mic_failure(struct ieee80211_key_conf *keyconf);
5992
5993/**
5994 * ieee80211_key_replay - increment replay counter for the key
5995 *
5996 * Note: this is really only safe if no other RX function is called
5997 * at the same time.
5998 *
5999 * @keyconf: the key in question
6000 */
6001void ieee80211_key_replay(struct ieee80211_key_conf *keyconf);
6002
6003/**
6004 * ieee80211_wake_queue - wake specific queue
6005 * @hw: pointer as obtained from ieee80211_alloc_hw().
6006 * @queue: queue number (counted from zero).
6007 *
6008 * Drivers must use this function instead of netif_wake_queue.
6009 */
6010void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue);
6011
6012/**
6013 * ieee80211_stop_queue - stop specific queue
6014 * @hw: pointer as obtained from ieee80211_alloc_hw().
6015 * @queue: queue number (counted from zero).
6016 *
6017 * Drivers must use this function instead of netif_stop_queue.
6018 */
6019void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue);
6020
6021/**
6022 * ieee80211_queue_stopped - test status of the queue
6023 * @hw: pointer as obtained from ieee80211_alloc_hw().
6024 * @queue: queue number (counted from zero).
6025 *
6026 * Drivers must use this function instead of netif_queue_stopped.
6027 *
6028 * Return: %true if the queue is stopped. %false otherwise.
6029 */
6030
6031int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue);
6032
6033/**
6034 * ieee80211_stop_queues - stop all queues
6035 * @hw: pointer as obtained from ieee80211_alloc_hw().
6036 *
6037 * Drivers must use this function instead of netif_tx_stop_all_queues.
6038 */
6039void ieee80211_stop_queues(struct ieee80211_hw *hw);
6040
6041/**
6042 * ieee80211_wake_queues - wake all queues
6043 * @hw: pointer as obtained from ieee80211_alloc_hw().
6044 *
6045 * Drivers must use this function instead of netif_tx_wake_all_queues.
6046 */
6047void ieee80211_wake_queues(struct ieee80211_hw *hw);
6048
6049/**
6050 * ieee80211_scan_completed - completed hardware scan
6051 *
6052 * When hardware scan offload is used (i.e. the hw_scan() callback is
6053 * assigned) this function needs to be called by the driver to notify
6054 * mac80211 that the scan finished. This function can be called from
6055 * any context, including hardirq context.
6056 *
6057 * @hw: the hardware that finished the scan
6058 * @info: information about the completed scan
6059 */
6060void ieee80211_scan_completed(struct ieee80211_hw *hw,
6061 struct cfg80211_scan_info *info);
6062
6063/**
6064 * ieee80211_sched_scan_results - got results from scheduled scan
6065 *
6066 * When a scheduled scan is running, this function needs to be called by the
6067 * driver whenever there are new scan results available.
6068 *
6069 * @hw: the hardware that is performing scheduled scans
6070 */
6071void ieee80211_sched_scan_results(struct ieee80211_hw *hw);
6072
6073/**
6074 * ieee80211_sched_scan_stopped - inform that the scheduled scan has stopped
6075 *
6076 * When a scheduled scan is running, this function can be called by
6077 * the driver if it needs to stop the scan to perform another task.
6078 * Usual scenarios are drivers that cannot continue the scheduled scan
6079 * while associating, for instance.
6080 *
6081 * @hw: the hardware that is performing scheduled scans
6082 */
6083void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw);
6084
6085/**
6086 * enum ieee80211_interface_iteration_flags - interface iteration flags
6087 * @IEEE80211_IFACE_ITER_NORMAL: Iterate over all interfaces that have
6088 * been added to the driver; However, note that during hardware
6089 * reconfiguration (after restart_hw) it will iterate over a new
6090 * interface and over all the existing interfaces even if they
6091 * haven't been re-added to the driver yet.
6092 * @IEEE80211_IFACE_ITER_RESUME_ALL: During resume, iterate over all
6093 * interfaces, even if they haven't been re-added to the driver yet.
6094 * @IEEE80211_IFACE_ITER_ACTIVE: Iterate only active interfaces (netdev is up).
6095 * @IEEE80211_IFACE_SKIP_SDATA_NOT_IN_DRIVER: Skip any interfaces where SDATA
6096 * is not in the driver. This may fix crashes during firmware recovery
6097 * for instance.
6098 */
6099enum ieee80211_interface_iteration_flags {
6100 IEEE80211_IFACE_ITER_NORMAL = 0,
6101 IEEE80211_IFACE_ITER_RESUME_ALL = BIT(0),
6102 IEEE80211_IFACE_ITER_ACTIVE = BIT(1),
6103 IEEE80211_IFACE_SKIP_SDATA_NOT_IN_DRIVER = BIT(2),
6104};
6105
6106/**
6107 * ieee80211_iterate_interfaces - iterate interfaces
6108 *
6109 * This function iterates over the interfaces associated with a given
6110 * hardware and calls the callback for them. This includes active as well as
6111 * inactive interfaces. This function allows the iterator function to sleep.
6112 * Will iterate over a new interface during add_interface().
6113 *
6114 * @hw: the hardware struct of which the interfaces should be iterated over
6115 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
6116 * @iterator: the iterator function to call
6117 * @data: first argument of the iterator function
6118 */
6119void ieee80211_iterate_interfaces(struct ieee80211_hw *hw, u32 iter_flags,
6120 void (*iterator)(void *data, u8 *mac,
6121 struct ieee80211_vif *vif),
6122 void *data);
6123
6124/**
6125 * ieee80211_iterate_active_interfaces - iterate active interfaces
6126 *
6127 * This function iterates over the interfaces associated with a given
6128 * hardware that are currently active and calls the callback for them.
6129 * This function allows the iterator function to sleep, when the iterator
6130 * function is atomic @ieee80211_iterate_active_interfaces_atomic can
6131 * be used.
6132 * Does not iterate over a new interface during add_interface().
6133 *
6134 * @hw: the hardware struct of which the interfaces should be iterated over
6135 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
6136 * @iterator: the iterator function to call
6137 * @data: first argument of the iterator function
6138 */
6139static inline void
6140ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, u32 iter_flags,
6141 void (*iterator)(void *data, u8 *mac,
6142 struct ieee80211_vif *vif),
6143 void *data)
6144{
6145 ieee80211_iterate_interfaces(hw,
6146 iter_flags | IEEE80211_IFACE_ITER_ACTIVE,
6147 iterator, data);
6148}
6149
6150/**
6151 * ieee80211_iterate_active_interfaces_atomic - iterate active interfaces
6152 *
6153 * This function iterates over the interfaces associated with a given
6154 * hardware that are currently active and calls the callback for them.
6155 * This function requires the iterator callback function to be atomic,
6156 * if that is not desired, use @ieee80211_iterate_active_interfaces instead.
6157 * Does not iterate over a new interface during add_interface().
6158 *
6159 * @hw: the hardware struct of which the interfaces should be iterated over
6160 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
6161 * @iterator: the iterator function to call, cannot sleep
6162 * @data: first argument of the iterator function
6163 */
6164void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw,
6165 u32 iter_flags,
6166 void (*iterator)(void *data,
6167 u8 *mac,
6168 struct ieee80211_vif *vif),
6169 void *data);
6170
6171/**
6172 * ieee80211_iterate_active_interfaces_mtx - iterate active interfaces
6173 *
6174 * This function iterates over the interfaces associated with a given
6175 * hardware that are currently active and calls the callback for them.
6176 * This version can only be used while holding the wiphy mutex.
6177 *
6178 * @hw: the hardware struct of which the interfaces should be iterated over
6179 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
6180 * @iterator: the iterator function to call, cannot sleep
6181 * @data: first argument of the iterator function
6182 */
6183void ieee80211_iterate_active_interfaces_mtx(struct ieee80211_hw *hw,
6184 u32 iter_flags,
6185 void (*iterator)(void *data,
6186 u8 *mac,
6187 struct ieee80211_vif *vif),
6188 void *data);
6189
6190/**
6191 * ieee80211_iterate_stations_atomic - iterate stations
6192 *
6193 * This function iterates over all stations associated with a given
6194 * hardware that are currently uploaded to the driver and calls the callback
6195 * function for them.
6196 * This function requires the iterator callback function to be atomic,
6197 *
6198 * @hw: the hardware struct of which the interfaces should be iterated over
6199 * @iterator: the iterator function to call, cannot sleep
6200 * @data: first argument of the iterator function
6201 */
6202void ieee80211_iterate_stations_atomic(struct ieee80211_hw *hw,
6203 void (*iterator)(void *data,
6204 struct ieee80211_sta *sta),
6205 void *data);
6206/**
6207 * ieee80211_queue_work - add work onto the mac80211 workqueue
6208 *
6209 * Drivers and mac80211 use this to add work onto the mac80211 workqueue.
6210 * This helper ensures drivers are not queueing work when they should not be.
6211 *
6212 * @hw: the hardware struct for the interface we are adding work for
6213 * @work: the work we want to add onto the mac80211 workqueue
6214 */
6215void ieee80211_queue_work(struct ieee80211_hw *hw, struct work_struct *work);
6216
6217/**
6218 * ieee80211_queue_delayed_work - add work onto the mac80211 workqueue
6219 *
6220 * Drivers and mac80211 use this to queue delayed work onto the mac80211
6221 * workqueue.
6222 *
6223 * @hw: the hardware struct for the interface we are adding work for
6224 * @dwork: delayable work to queue onto the mac80211 workqueue
6225 * @delay: number of jiffies to wait before queueing
6226 */
6227void ieee80211_queue_delayed_work(struct ieee80211_hw *hw,
6228 struct delayed_work *dwork,
6229 unsigned long delay);
6230
6231/**
6232 * ieee80211_refresh_tx_agg_session_timer - Refresh a tx agg session timer.
6233 * @sta: the station for which to start a BA session
6234 * @tid: the TID to BA on.
6235 *
6236 * This function allows low level driver to refresh tx agg session timer
6237 * to maintain BA session, the session level will still be managed by the
6238 * mac80211.
6239 *
6240 * Note: must be called in an RCU critical section.
6241 */
6242void ieee80211_refresh_tx_agg_session_timer(struct ieee80211_sta *sta,
6243 u16 tid);
6244
6245/**
6246 * ieee80211_start_tx_ba_session - Start a tx Block Ack session.
6247 * @sta: the station for which to start a BA session
6248 * @tid: the TID to BA on.
6249 * @timeout: session timeout value (in TUs)
6250 *
6251 * Return: success if addBA request was sent, failure otherwise
6252 *
6253 * Although mac80211/low level driver/user space application can estimate
6254 * the need to start aggregation on a certain RA/TID, the session level
6255 * will be managed by the mac80211.
6256 */
6257int ieee80211_start_tx_ba_session(struct ieee80211_sta *sta, u16 tid,
6258 u16 timeout);
6259
6260/**
6261 * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate.
6262 * @vif: &struct ieee80211_vif pointer from the add_interface callback
6263 * @ra: receiver address of the BA session recipient.
6264 * @tid: the TID to BA on.
6265 *
6266 * This function must be called by low level driver once it has
6267 * finished with preparations for the BA session. It can be called
6268 * from any context.
6269 */
6270void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
6271 u16 tid);
6272
6273/**
6274 * ieee80211_stop_tx_ba_session - Stop a Block Ack session.
6275 * @sta: the station whose BA session to stop
6276 * @tid: the TID to stop BA.
6277 *
6278 * Return: negative error if the TID is invalid, or no aggregation active
6279 *
6280 * Although mac80211/low level driver/user space application can estimate
6281 * the need to stop aggregation on a certain RA/TID, the session level
6282 * will be managed by the mac80211.
6283 */
6284int ieee80211_stop_tx_ba_session(struct ieee80211_sta *sta, u16 tid);
6285
6286/**
6287 * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate.
6288 * @vif: &struct ieee80211_vif pointer from the add_interface callback
6289 * @ra: receiver address of the BA session recipient.
6290 * @tid: the desired TID to BA on.
6291 *
6292 * This function must be called by low level driver once it has
6293 * finished with preparations for the BA session tear down. It
6294 * can be called from any context.
6295 */
6296void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
6297 u16 tid);
6298
6299/**
6300 * ieee80211_find_sta - find a station
6301 *
6302 * @vif: virtual interface to look for station on
6303 * @addr: station's address
6304 *
6305 * Return: The station, if found. %NULL otherwise.
6306 *
6307 * Note: This function must be called under RCU lock and the
6308 * resulting pointer is only valid under RCU lock as well.
6309 */
6310struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif,
6311 const u8 *addr);
6312
6313/**
6314 * ieee80211_find_sta_by_ifaddr - find a station on hardware
6315 *
6316 * @hw: pointer as obtained from ieee80211_alloc_hw()
6317 * @addr: remote station's address
6318 * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'.
6319 *
6320 * Return: The station, if found. %NULL otherwise.
6321 *
6322 * Note: This function must be called under RCU lock and the
6323 * resulting pointer is only valid under RCU lock as well.
6324 *
6325 * NOTE: You may pass NULL for localaddr, but then you will just get
6326 * the first STA that matches the remote address 'addr'.
6327 * We can have multiple STA associated with multiple
6328 * logical stations (e.g. consider a station connecting to another
6329 * BSSID on the same AP hardware without disconnecting first).
6330 * In this case, the result of this method with localaddr NULL
6331 * is not reliable.
6332 *
6333 * DO NOT USE THIS FUNCTION with localaddr NULL if at all possible.
6334 */
6335struct ieee80211_sta *ieee80211_find_sta_by_ifaddr(struct ieee80211_hw *hw,
6336 const u8 *addr,
6337 const u8 *localaddr);
6338
6339/**
6340 * ieee80211_find_sta_by_link_addrs - find STA by link addresses
6341 * @hw: pointer as obtained from ieee80211_alloc_hw()
6342 * @addr: remote station's link address
6343 * @localaddr: local link address, use %NULL for any (but avoid that)
6344 * @link_id: pointer to obtain the link ID if the STA is found,
6345 * may be %NULL if the link ID is not needed
6346 *
6347 * Obtain the STA by link address, must use RCU protection.
6348 */
6349struct ieee80211_sta *
6350ieee80211_find_sta_by_link_addrs(struct ieee80211_hw *hw,
6351 const u8 *addr,
6352 const u8 *localaddr,
6353 unsigned int *link_id);
6354
6355/**
6356 * ieee80211_sta_block_awake - block station from waking up
6357 * @hw: the hardware
6358 * @pubsta: the station
6359 * @block: whether to block or unblock
6360 *
6361 * Some devices require that all frames that are on the queues
6362 * for a specific station that went to sleep are flushed before
6363 * a poll response or frames after the station woke up can be
6364 * delivered to that it. Note that such frames must be rejected
6365 * by the driver as filtered, with the appropriate status flag.
6366 *
6367 * This function allows implementing this mode in a race-free
6368 * manner.
6369 *
6370 * To do this, a driver must keep track of the number of frames
6371 * still enqueued for a specific station. If this number is not
6372 * zero when the station goes to sleep, the driver must call
6373 * this function to force mac80211 to consider the station to
6374 * be asleep regardless of the station's actual state. Once the
6375 * number of outstanding frames reaches zero, the driver must
6376 * call this function again to unblock the station. That will
6377 * cause mac80211 to be able to send ps-poll responses, and if
6378 * the station queried in the meantime then frames will also
6379 * be sent out as a result of this. Additionally, the driver
6380 * will be notified that the station woke up some time after
6381 * it is unblocked, regardless of whether the station actually
6382 * woke up while blocked or not.
6383 */
6384void ieee80211_sta_block_awake(struct ieee80211_hw *hw,
6385 struct ieee80211_sta *pubsta, bool block);
6386
6387/**
6388 * ieee80211_sta_eosp - notify mac80211 about end of SP
6389 * @pubsta: the station
6390 *
6391 * When a device transmits frames in a way that it can't tell
6392 * mac80211 in the TX status about the EOSP, it must clear the
6393 * %IEEE80211_TX_STATUS_EOSP bit and call this function instead.
6394 * This applies for PS-Poll as well as uAPSD.
6395 *
6396 * Note that just like with _tx_status() and _rx() drivers must
6397 * not mix calls to irqsafe/non-irqsafe versions, this function
6398 * must not be mixed with those either. Use the all irqsafe, or
6399 * all non-irqsafe, don't mix!
6400 *
6401 * NB: the _irqsafe version of this function doesn't exist, no
6402 * driver needs it right now. Don't call this function if
6403 * you'd need the _irqsafe version, look at the git history
6404 * and restore the _irqsafe version!
6405 */
6406void ieee80211_sta_eosp(struct ieee80211_sta *pubsta);
6407
6408/**
6409 * ieee80211_send_eosp_nullfunc - ask mac80211 to send NDP with EOSP
6410 * @pubsta: the station
6411 * @tid: the tid of the NDP
6412 *
6413 * Sometimes the device understands that it needs to close
6414 * the Service Period unexpectedly. This can happen when
6415 * sending frames that are filling holes in the BA window.
6416 * In this case, the device can ask mac80211 to send a
6417 * Nullfunc frame with EOSP set. When that happens, the
6418 * driver must have called ieee80211_sta_set_buffered() to
6419 * let mac80211 know that there are no buffered frames any
6420 * more, otherwise mac80211 will get the more_data bit wrong.
6421 * The low level driver must have made sure that the frame
6422 * will be sent despite the station being in power-save.
6423 * Mac80211 won't call allow_buffered_frames().
6424 * Note that calling this function, doesn't exempt the driver
6425 * from closing the EOSP properly, it will still have to call
6426 * ieee80211_sta_eosp when the NDP is sent.
6427 */
6428void ieee80211_send_eosp_nullfunc(struct ieee80211_sta *pubsta, int tid);
6429
6430/**
6431 * ieee80211_sta_recalc_aggregates - recalculate aggregate data after a change
6432 * @pubsta: the station
6433 *
6434 * Call this function after changing a per-link aggregate data as referenced in
6435 * &struct ieee80211_sta_aggregates by accessing the agg field of
6436 * &struct ieee80211_link_sta.
6437 *
6438 * With non MLO the data in deflink will be referenced directly. In that case
6439 * there is no need to call this function.
6440 */
6441void ieee80211_sta_recalc_aggregates(struct ieee80211_sta *pubsta);
6442
6443/**
6444 * ieee80211_sta_register_airtime - register airtime usage for a sta/tid
6445 *
6446 * Register airtime usage for a given sta on a given tid. The driver must call
6447 * this function to notify mac80211 that a station used a certain amount of
6448 * airtime. This information will be used by the TXQ scheduler to schedule
6449 * stations in a way that ensures airtime fairness.
6450 *
6451 * The reported airtime should as a minimum include all time that is spent
6452 * transmitting to the remote station, including overhead and padding, but not
6453 * including time spent waiting for a TXOP. If the time is not reported by the
6454 * hardware it can in some cases be calculated from the rate and known frame
6455 * composition. When possible, the time should include any failed transmission
6456 * attempts.
6457 *
6458 * The driver can either call this function synchronously for every packet or
6459 * aggregate, or asynchronously as airtime usage information becomes available.
6460 * TX and RX airtime can be reported together, or separately by setting one of
6461 * them to 0.
6462 *
6463 * @pubsta: the station
6464 * @tid: the TID to register airtime for
6465 * @tx_airtime: airtime used during TX (in usec)
6466 * @rx_airtime: airtime used during RX (in usec)
6467 */
6468void ieee80211_sta_register_airtime(struct ieee80211_sta *pubsta, u8 tid,
6469 u32 tx_airtime, u32 rx_airtime);
6470
6471/**
6472 * ieee80211_txq_airtime_check - check if a txq can send frame to device
6473 *
6474 * @hw: pointer obtained from ieee80211_alloc_hw()
6475 * @txq: pointer obtained from station or virtual interface
6476 *
6477 * Return true if the AQL's airtime limit has not been reached and the txq can
6478 * continue to send more packets to the device. Otherwise return false.
6479 */
6480bool
6481ieee80211_txq_airtime_check(struct ieee80211_hw *hw, struct ieee80211_txq *txq);
6482
6483/**
6484 * ieee80211_iter_keys - iterate keys programmed into the device
6485 * @hw: pointer obtained from ieee80211_alloc_hw()
6486 * @vif: virtual interface to iterate, may be %NULL for all
6487 * @iter: iterator function that will be called for each key
6488 * @iter_data: custom data to pass to the iterator function
6489 *
6490 * Context: Must be called with wiphy mutex held; can sleep.
6491 *
6492 * This function can be used to iterate all the keys known to
6493 * mac80211, even those that weren't previously programmed into
6494 * the device. This is intended for use in WoWLAN if the device
6495 * needs reprogramming of the keys during suspend.
6496 *
6497 * The order in which the keys are iterated matches the order
6498 * in which they were originally installed and handed to the
6499 * set_key callback.
6500 */
6501void ieee80211_iter_keys(struct ieee80211_hw *hw,
6502 struct ieee80211_vif *vif,
6503 void (*iter)(struct ieee80211_hw *hw,
6504 struct ieee80211_vif *vif,
6505 struct ieee80211_sta *sta,
6506 struct ieee80211_key_conf *key,
6507 void *data),
6508 void *iter_data);
6509
6510/**
6511 * ieee80211_iter_keys_rcu - iterate keys programmed into the device
6512 * @hw: pointer obtained from ieee80211_alloc_hw()
6513 * @vif: virtual interface to iterate, may be %NULL for all
6514 * @iter: iterator function that will be called for each key
6515 * @iter_data: custom data to pass to the iterator function
6516 *
6517 * This function can be used to iterate all the keys known to
6518 * mac80211, even those that weren't previously programmed into
6519 * the device. Note that due to locking reasons, keys of station
6520 * in removal process will be skipped.
6521 *
6522 * This function requires being called in an RCU critical section,
6523 * and thus iter must be atomic.
6524 */
6525void ieee80211_iter_keys_rcu(struct ieee80211_hw *hw,
6526 struct ieee80211_vif *vif,
6527 void (*iter)(struct ieee80211_hw *hw,
6528 struct ieee80211_vif *vif,
6529 struct ieee80211_sta *sta,
6530 struct ieee80211_key_conf *key,
6531 void *data),
6532 void *iter_data);
6533
6534/**
6535 * ieee80211_iter_chan_contexts_atomic - iterate channel contexts
6536 * @hw: pointer obtained from ieee80211_alloc_hw().
6537 * @iter: iterator function
6538 * @iter_data: data passed to iterator function
6539 *
6540 * Iterate all active channel contexts. This function is atomic and
6541 * doesn't acquire any locks internally that might be held in other
6542 * places while calling into the driver.
6543 *
6544 * The iterator will not find a context that's being added (during
6545 * the driver callback to add it) but will find it while it's being
6546 * removed.
6547 *
6548 * Note that during hardware restart, all contexts that existed
6549 * before the restart are considered already present so will be
6550 * found while iterating, whether they've been re-added already
6551 * or not.
6552 */
6553void ieee80211_iter_chan_contexts_atomic(
6554 struct ieee80211_hw *hw,
6555 void (*iter)(struct ieee80211_hw *hw,
6556 struct ieee80211_chanctx_conf *chanctx_conf,
6557 void *data),
6558 void *iter_data);
6559
6560/**
6561 * ieee80211_ap_probereq_get - retrieve a Probe Request template
6562 * @hw: pointer obtained from ieee80211_alloc_hw().
6563 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6564 *
6565 * Creates a Probe Request template which can, for example, be uploaded to
6566 * hardware. The template is filled with bssid, ssid and supported rate
6567 * information. This function must only be called from within the
6568 * .bss_info_changed callback function and only in managed mode. The function
6569 * is only useful when the interface is associated, otherwise it will return
6570 * %NULL.
6571 *
6572 * Return: The Probe Request template. %NULL on error.
6573 */
6574struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw,
6575 struct ieee80211_vif *vif);
6576
6577/**
6578 * ieee80211_beacon_loss - inform hardware does not receive beacons
6579 *
6580 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6581 *
6582 * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER and
6583 * %IEEE80211_CONF_PS is set, the driver needs to inform whenever the
6584 * hardware is not receiving beacons with this function.
6585 */
6586void ieee80211_beacon_loss(struct ieee80211_vif *vif);
6587
6588/**
6589 * ieee80211_connection_loss - inform hardware has lost connection to the AP
6590 *
6591 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6592 *
6593 * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER, and
6594 * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver
6595 * needs to inform if the connection to the AP has been lost.
6596 * The function may also be called if the connection needs to be terminated
6597 * for some other reason, even if %IEEE80211_HW_CONNECTION_MONITOR isn't set.
6598 *
6599 * This function will cause immediate change to disassociated state,
6600 * without connection recovery attempts.
6601 */
6602void ieee80211_connection_loss(struct ieee80211_vif *vif);
6603
6604/**
6605 * ieee80211_disconnect - request disconnection
6606 *
6607 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6608 * @reconnect: immediate reconnect is desired
6609 *
6610 * Request disconnection from the current network and, if enabled, send a
6611 * hint to the higher layers that immediate reconnect is desired.
6612 */
6613void ieee80211_disconnect(struct ieee80211_vif *vif, bool reconnect);
6614
6615/**
6616 * ieee80211_resume_disconnect - disconnect from AP after resume
6617 *
6618 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6619 *
6620 * Instructs mac80211 to disconnect from the AP after resume.
6621 * Drivers can use this after WoWLAN if they know that the
6622 * connection cannot be kept up, for example because keys were
6623 * used while the device was asleep but the replay counters or
6624 * similar cannot be retrieved from the device during resume.
6625 *
6626 * Note that due to implementation issues, if the driver uses
6627 * the reconfiguration functionality during resume the interface
6628 * will still be added as associated first during resume and then
6629 * disconnect normally later.
6630 *
6631 * This function can only be called from the resume callback and
6632 * the driver must not be holding any of its own locks while it
6633 * calls this function, or at least not any locks it needs in the
6634 * key configuration paths (if it supports HW crypto).
6635 */
6636void ieee80211_resume_disconnect(struct ieee80211_vif *vif);
6637
6638/**
6639 * ieee80211_hw_restart_disconnect - disconnect from AP after
6640 * hardware restart
6641 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6642 *
6643 * Instructs mac80211 to disconnect from the AP after
6644 * hardware restart.
6645 */
6646void ieee80211_hw_restart_disconnect(struct ieee80211_vif *vif);
6647
6648/**
6649 * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring
6650 * rssi threshold triggered
6651 *
6652 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6653 * @rssi_event: the RSSI trigger event type
6654 * @rssi_level: new RSSI level value or 0 if not available
6655 * @gfp: context flags
6656 *
6657 * When the %IEEE80211_VIF_SUPPORTS_CQM_RSSI is set, and a connection quality
6658 * monitoring is configured with an rssi threshold, the driver will inform
6659 * whenever the rssi level reaches the threshold.
6660 */
6661void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif,
6662 enum nl80211_cqm_rssi_threshold_event rssi_event,
6663 s32 rssi_level,
6664 gfp_t gfp);
6665
6666/**
6667 * ieee80211_cqm_beacon_loss_notify - inform CQM of beacon loss
6668 *
6669 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6670 * @gfp: context flags
6671 */
6672void ieee80211_cqm_beacon_loss_notify(struct ieee80211_vif *vif, gfp_t gfp);
6673
6674/**
6675 * ieee80211_radar_detected - inform that a radar was detected
6676 *
6677 * @hw: pointer as obtained from ieee80211_alloc_hw()
6678 */
6679void ieee80211_radar_detected(struct ieee80211_hw *hw);
6680
6681/**
6682 * ieee80211_chswitch_done - Complete channel switch process
6683 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6684 * @success: make the channel switch successful or not
6685 * @link_id: the link_id on which the switch was done. Ignored if success is
6686 * false.
6687 *
6688 * Complete the channel switch post-process: set the new operational channel
6689 * and wake up the suspended queues.
6690 */
6691void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success,
6692 unsigned int link_id);
6693
6694/**
6695 * ieee80211_channel_switch_disconnect - disconnect due to channel switch error
6696 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6697 * @block_tx: if %true, do not send deauth frame.
6698 *
6699 * Instruct mac80211 to disconnect due to a channel switch error. The channel
6700 * switch can request to block the tx and so, we need to make sure we do not send
6701 * a deauth frame in this case.
6702 */
6703void ieee80211_channel_switch_disconnect(struct ieee80211_vif *vif,
6704 bool block_tx);
6705
6706/**
6707 * ieee80211_request_smps - request SM PS transition
6708 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6709 * @link_id: link ID for MLO, or 0
6710 * @smps_mode: new SM PS mode
6711 *
6712 * This allows the driver to request an SM PS transition in managed
6713 * mode. This is useful when the driver has more information than
6714 * the stack about possible interference, for example by bluetooth.
6715 */
6716void ieee80211_request_smps(struct ieee80211_vif *vif, unsigned int link_id,
6717 enum ieee80211_smps_mode smps_mode);
6718
6719/**
6720 * ieee80211_ready_on_channel - notification of remain-on-channel start
6721 * @hw: pointer as obtained from ieee80211_alloc_hw()
6722 */
6723void ieee80211_ready_on_channel(struct ieee80211_hw *hw);
6724
6725/**
6726 * ieee80211_remain_on_channel_expired - remain_on_channel duration expired
6727 * @hw: pointer as obtained from ieee80211_alloc_hw()
6728 */
6729void ieee80211_remain_on_channel_expired(struct ieee80211_hw *hw);
6730
6731/**
6732 * ieee80211_stop_rx_ba_session - callback to stop existing BA sessions
6733 *
6734 * in order not to harm the system performance and user experience, the device
6735 * may request not to allow any rx ba session and tear down existing rx ba
6736 * sessions based on system constraints such as periodic BT activity that needs
6737 * to limit wlan activity (eg.sco or a2dp)."
6738 * in such cases, the intention is to limit the duration of the rx ppdu and
6739 * therefore prevent the peer device to use a-mpdu aggregation.
6740 *
6741 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6742 * @ba_rx_bitmap: Bit map of open rx ba per tid
6743 * @addr: & to bssid mac address
6744 */
6745void ieee80211_stop_rx_ba_session(struct ieee80211_vif *vif, u16 ba_rx_bitmap,
6746 const u8 *addr);
6747
6748/**
6749 * ieee80211_mark_rx_ba_filtered_frames - move RX BA window and mark filtered
6750 * @pubsta: station struct
6751 * @tid: the session's TID
6752 * @ssn: starting sequence number of the bitmap, all frames before this are
6753 * assumed to be out of the window after the call
6754 * @filtered: bitmap of filtered frames, BIT(0) is the @ssn entry etc.
6755 * @received_mpdus: number of received mpdus in firmware
6756 *
6757 * This function moves the BA window and releases all frames before @ssn, and
6758 * marks frames marked in the bitmap as having been filtered. Afterwards, it
6759 * checks if any frames in the window starting from @ssn can now be released
6760 * (in case they were only waiting for frames that were filtered.)
6761 * (Only work correctly if @max_rx_aggregation_subframes <= 64 frames)
6762 */
6763void ieee80211_mark_rx_ba_filtered_frames(struct ieee80211_sta *pubsta, u8 tid,
6764 u16 ssn, u64 filtered,
6765 u16 received_mpdus);
6766
6767/**
6768 * ieee80211_send_bar - send a BlockAckReq frame
6769 *
6770 * can be used to flush pending frames from the peer's aggregation reorder
6771 * buffer.
6772 *
6773 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6774 * @ra: the peer's destination address
6775 * @tid: the TID of the aggregation session
6776 * @ssn: the new starting sequence number for the receiver
6777 */
6778void ieee80211_send_bar(struct ieee80211_vif *vif, u8 *ra, u16 tid, u16 ssn);
6779
6780/**
6781 * ieee80211_manage_rx_ba_offl - helper to queue an RX BA work
6782 * @vif: &struct ieee80211_vif pointer from the add_interface callback
6783 * @addr: station mac address
6784 * @tid: the rx tid
6785 */
6786void ieee80211_manage_rx_ba_offl(struct ieee80211_vif *vif, const u8 *addr,
6787 unsigned int tid);
6788
6789/**
6790 * ieee80211_start_rx_ba_session_offl - start a Rx BA session
6791 *
6792 * Some device drivers may offload part of the Rx aggregation flow including
6793 * AddBa/DelBa negotiation but may otherwise be incapable of full Rx
6794 * reordering.
6795 *
6796 * Create structures responsible for reordering so device drivers may call here
6797 * when they complete AddBa negotiation.
6798 *
6799 * @vif: &struct ieee80211_vif pointer from the add_interface callback
6800 * @addr: station mac address
6801 * @tid: the rx tid
6802 */
6803static inline void ieee80211_start_rx_ba_session_offl(struct ieee80211_vif *vif,
6804 const u8 *addr, u16 tid)
6805{
6806 if (WARN_ON(tid >= IEEE80211_NUM_TIDS))
6807 return;
6808 ieee80211_manage_rx_ba_offl(vif, addr, tid);
6809}
6810
6811/**
6812 * ieee80211_stop_rx_ba_session_offl - stop a Rx BA session
6813 *
6814 * Some device drivers may offload part of the Rx aggregation flow including
6815 * AddBa/DelBa negotiation but may otherwise be incapable of full Rx
6816 * reordering.
6817 *
6818 * Destroy structures responsible for reordering so device drivers may call here
6819 * when they complete DelBa negotiation.
6820 *
6821 * @vif: &struct ieee80211_vif pointer from the add_interface callback
6822 * @addr: station mac address
6823 * @tid: the rx tid
6824 */
6825static inline void ieee80211_stop_rx_ba_session_offl(struct ieee80211_vif *vif,
6826 const u8 *addr, u16 tid)
6827{
6828 if (WARN_ON(tid >= IEEE80211_NUM_TIDS))
6829 return;
6830 ieee80211_manage_rx_ba_offl(vif, addr, tid + IEEE80211_NUM_TIDS);
6831}
6832
6833/**
6834 * ieee80211_rx_ba_timer_expired - stop a Rx BA session due to timeout
6835 *
6836 * Some device drivers do not offload AddBa/DelBa negotiation, but handle rx
6837 * buffer reording internally, and therefore also handle the session timer.
6838 *
6839 * Trigger the timeout flow, which sends a DelBa.
6840 *
6841 * @vif: &struct ieee80211_vif pointer from the add_interface callback
6842 * @addr: station mac address
6843 * @tid: the rx tid
6844 */
6845void ieee80211_rx_ba_timer_expired(struct ieee80211_vif *vif,
6846 const u8 *addr, unsigned int tid);
6847
6848/* Rate control API */
6849
6850/**
6851 * struct ieee80211_tx_rate_control - rate control information for/from RC algo
6852 *
6853 * @hw: The hardware the algorithm is invoked for.
6854 * @sband: The band this frame is being transmitted on.
6855 * @bss_conf: the current BSS configuration
6856 * @skb: the skb that will be transmitted, the control information in it needs
6857 * to be filled in
6858 * @reported_rate: The rate control algorithm can fill this in to indicate
6859 * which rate should be reported to userspace as the current rate and
6860 * used for rate calculations in the mesh network.
6861 * @rts: whether RTS will be used for this frame because it is longer than the
6862 * RTS threshold
6863 * @short_preamble: whether mac80211 will request short-preamble transmission
6864 * if the selected rate supports it
6865 * @rate_idx_mask: user-requested (legacy) rate mask
6866 * @rate_idx_mcs_mask: user-requested MCS rate mask (NULL if not in use)
6867 * @bss: whether this frame is sent out in AP or IBSS mode
6868 */
6869struct ieee80211_tx_rate_control {
6870 struct ieee80211_hw *hw;
6871 struct ieee80211_supported_band *sband;
6872 struct ieee80211_bss_conf *bss_conf;
6873 struct sk_buff *skb;
6874 struct ieee80211_tx_rate reported_rate;
6875 bool rts, short_preamble;
6876 u32 rate_idx_mask;
6877 u8 *rate_idx_mcs_mask;
6878 bool bss;
6879};
6880
6881/**
6882 * enum rate_control_capabilities - rate control capabilities
6883 */
6884enum rate_control_capabilities {
6885 /**
6886 * @RATE_CTRL_CAPA_VHT_EXT_NSS_BW:
6887 * Support for extended NSS BW support (dot11VHTExtendedNSSCapable)
6888 * Note that this is only looked at if the minimum number of chains
6889 * that the AP uses is < the number of TX chains the hardware has,
6890 * otherwise the NSS difference doesn't bother us.
6891 */
6892 RATE_CTRL_CAPA_VHT_EXT_NSS_BW = BIT(0),
6893 /**
6894 * @RATE_CTRL_CAPA_AMPDU_TRIGGER:
6895 * mac80211 should start A-MPDU sessions on tx
6896 */
6897 RATE_CTRL_CAPA_AMPDU_TRIGGER = BIT(1),
6898};
6899
6900struct rate_control_ops {
6901 unsigned long capa;
6902 const char *name;
6903 void *(*alloc)(struct ieee80211_hw *hw);
6904 void (*add_debugfs)(struct ieee80211_hw *hw, void *priv,
6905 struct dentry *debugfsdir);
6906 void (*free)(void *priv);
6907
6908 void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp);
6909 void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
6910 struct cfg80211_chan_def *chandef,
6911 struct ieee80211_sta *sta, void *priv_sta);
6912 void (*rate_update)(void *priv, struct ieee80211_supported_band *sband,
6913 struct cfg80211_chan_def *chandef,
6914 struct ieee80211_sta *sta, void *priv_sta,
6915 u32 changed);
6916 void (*free_sta)(void *priv, struct ieee80211_sta *sta,
6917 void *priv_sta);
6918
6919 void (*tx_status_ext)(void *priv,
6920 struct ieee80211_supported_band *sband,
6921 void *priv_sta, struct ieee80211_tx_status *st);
6922 void (*tx_status)(void *priv, struct ieee80211_supported_band *sband,
6923 struct ieee80211_sta *sta, void *priv_sta,
6924 struct sk_buff *skb);
6925 void (*get_rate)(void *priv, struct ieee80211_sta *sta, void *priv_sta,
6926 struct ieee80211_tx_rate_control *txrc);
6927
6928 void (*add_sta_debugfs)(void *priv, void *priv_sta,
6929 struct dentry *dir);
6930
6931 u32 (*get_expected_throughput)(void *priv_sta);
6932};
6933
6934static inline int rate_supported(struct ieee80211_sta *sta,
6935 enum nl80211_band band,
6936 int index)
6937{
6938 return (sta == NULL || sta->deflink.supp_rates[band] & BIT(index));
6939}
6940
6941static inline s8
6942rate_lowest_index(struct ieee80211_supported_band *sband,
6943 struct ieee80211_sta *sta)
6944{
6945 int i;
6946
6947 for (i = 0; i < sband->n_bitrates; i++)
6948 if (rate_supported(sta, sband->band, i))
6949 return i;
6950
6951 /* warn when we cannot find a rate. */
6952 WARN_ON_ONCE(1);
6953
6954 /* and return 0 (the lowest index) */
6955 return 0;
6956}
6957
6958static inline
6959bool rate_usable_index_exists(struct ieee80211_supported_band *sband,
6960 struct ieee80211_sta *sta)
6961{
6962 unsigned int i;
6963
6964 for (i = 0; i < sband->n_bitrates; i++)
6965 if (rate_supported(sta, sband->band, i))
6966 return true;
6967 return false;
6968}
6969
6970/**
6971 * rate_control_set_rates - pass the sta rate selection to mac80211/driver
6972 *
6973 * When not doing a rate control probe to test rates, rate control should pass
6974 * its rate selection to mac80211. If the driver supports receiving a station
6975 * rate table, it will use it to ensure that frames are always sent based on
6976 * the most recent rate control module decision.
6977 *
6978 * @hw: pointer as obtained from ieee80211_alloc_hw()
6979 * @pubsta: &struct ieee80211_sta pointer to the target destination.
6980 * @rates: new tx rate set to be used for this station.
6981 */
6982int rate_control_set_rates(struct ieee80211_hw *hw,
6983 struct ieee80211_sta *pubsta,
6984 struct ieee80211_sta_rates *rates);
6985
6986int ieee80211_rate_control_register(const struct rate_control_ops *ops);
6987void ieee80211_rate_control_unregister(const struct rate_control_ops *ops);
6988
6989static inline bool
6990conf_is_ht20(struct ieee80211_conf *conf)
6991{
6992 return conf->chandef.width == NL80211_CHAN_WIDTH_20;
6993}
6994
6995static inline bool
6996conf_is_ht40_minus(struct ieee80211_conf *conf)
6997{
6998 return conf->chandef.width == NL80211_CHAN_WIDTH_40 &&
6999 conf->chandef.center_freq1 < conf->chandef.chan->center_freq;
7000}
7001
7002static inline bool
7003conf_is_ht40_plus(struct ieee80211_conf *conf)
7004{
7005 return conf->chandef.width == NL80211_CHAN_WIDTH_40 &&
7006 conf->chandef.center_freq1 > conf->chandef.chan->center_freq;
7007}
7008
7009static inline bool
7010conf_is_ht40(struct ieee80211_conf *conf)
7011{
7012 return conf->chandef.width == NL80211_CHAN_WIDTH_40;
7013}
7014
7015static inline bool
7016conf_is_ht(struct ieee80211_conf *conf)
7017{
7018 return (conf->chandef.width != NL80211_CHAN_WIDTH_5) &&
7019 (conf->chandef.width != NL80211_CHAN_WIDTH_10) &&
7020 (conf->chandef.width != NL80211_CHAN_WIDTH_20_NOHT);
7021}
7022
7023static inline enum nl80211_iftype
7024ieee80211_iftype_p2p(enum nl80211_iftype type, bool p2p)
7025{
7026 if (p2p) {
7027 switch (type) {
7028 case NL80211_IFTYPE_STATION:
7029 return NL80211_IFTYPE_P2P_CLIENT;
7030 case NL80211_IFTYPE_AP:
7031 return NL80211_IFTYPE_P2P_GO;
7032 default:
7033 break;
7034 }
7035 }
7036 return type;
7037}
7038
7039static inline enum nl80211_iftype
7040ieee80211_vif_type_p2p(struct ieee80211_vif *vif)
7041{
7042 return ieee80211_iftype_p2p(vif->type, vif->p2p);
7043}
7044
7045/**
7046 * ieee80211_get_he_iftype_cap_vif - return HE capabilities for sband/vif
7047 * @sband: the sband to search for the iftype on
7048 * @vif: the vif to get the iftype from
7049 *
7050 * Return: pointer to the struct ieee80211_sta_he_cap, or %NULL is none found
7051 */
7052static inline const struct ieee80211_sta_he_cap *
7053ieee80211_get_he_iftype_cap_vif(const struct ieee80211_supported_band *sband,
7054 struct ieee80211_vif *vif)
7055{
7056 return ieee80211_get_he_iftype_cap(sband, ieee80211_vif_type_p2p(vif));
7057}
7058
7059/**
7060 * ieee80211_get_he_6ghz_capa_vif - return HE 6 GHz capabilities
7061 * @sband: the sband to search for the STA on
7062 * @vif: the vif to get the iftype from
7063 *
7064 * Return: the 6GHz capabilities
7065 */
7066static inline __le16
7067ieee80211_get_he_6ghz_capa_vif(const struct ieee80211_supported_band *sband,
7068 struct ieee80211_vif *vif)
7069{
7070 return ieee80211_get_he_6ghz_capa(sband, ieee80211_vif_type_p2p(vif));
7071}
7072
7073/**
7074 * ieee80211_get_eht_iftype_cap_vif - return ETH capabilities for sband/vif
7075 * @sband: the sband to search for the iftype on
7076 * @vif: the vif to get the iftype from
7077 *
7078 * Return: pointer to the struct ieee80211_sta_eht_cap, or %NULL is none found
7079 */
7080static inline const struct ieee80211_sta_eht_cap *
7081ieee80211_get_eht_iftype_cap_vif(const struct ieee80211_supported_band *sband,
7082 struct ieee80211_vif *vif)
7083{
7084 return ieee80211_get_eht_iftype_cap(sband, ieee80211_vif_type_p2p(vif));
7085}
7086
7087/**
7088 * ieee80211_update_mu_groups - set the VHT MU-MIMO groud data
7089 *
7090 * @vif: the specified virtual interface
7091 * @link_id: the link ID for MLO, otherwise 0
7092 * @membership: 64 bits array - a bit is set if station is member of the group
7093 * @position: 2 bits per group id indicating the position in the group
7094 *
7095 * Note: This function assumes that the given vif is valid and the position and
7096 * membership data is of the correct size and are in the same byte order as the
7097 * matching GroupId management frame.
7098 * Calls to this function need to be serialized with RX path.
7099 */
7100void ieee80211_update_mu_groups(struct ieee80211_vif *vif, unsigned int link_id,
7101 const u8 *membership, const u8 *position);
7102
7103void ieee80211_enable_rssi_reports(struct ieee80211_vif *vif,
7104 int rssi_min_thold,
7105 int rssi_max_thold);
7106
7107void ieee80211_disable_rssi_reports(struct ieee80211_vif *vif);
7108
7109/**
7110 * ieee80211_ave_rssi - report the average RSSI for the specified interface
7111 *
7112 * @vif: the specified virtual interface
7113 *
7114 * Note: This function assumes that the given vif is valid.
7115 *
7116 * Return: The average RSSI value for the requested interface, or 0 if not
7117 * applicable.
7118 */
7119int ieee80211_ave_rssi(struct ieee80211_vif *vif);
7120
7121/**
7122 * ieee80211_report_wowlan_wakeup - report WoWLAN wakeup
7123 * @vif: virtual interface
7124 * @wakeup: wakeup reason(s)
7125 * @gfp: allocation flags
7126 *
7127 * See cfg80211_report_wowlan_wakeup().
7128 */
7129void ieee80211_report_wowlan_wakeup(struct ieee80211_vif *vif,
7130 struct cfg80211_wowlan_wakeup *wakeup,
7131 gfp_t gfp);
7132
7133/**
7134 * ieee80211_tx_prepare_skb - prepare an 802.11 skb for transmission
7135 * @hw: pointer as obtained from ieee80211_alloc_hw()
7136 * @vif: virtual interface
7137 * @skb: frame to be sent from within the driver
7138 * @band: the band to transmit on
7139 * @sta: optional pointer to get the station to send the frame to
7140 *
7141 * Note: must be called under RCU lock
7142 */
7143bool ieee80211_tx_prepare_skb(struct ieee80211_hw *hw,
7144 struct ieee80211_vif *vif, struct sk_buff *skb,
7145 int band, struct ieee80211_sta **sta);
7146
7147/**
7148 * ieee80211_parse_tx_radiotap - Sanity-check and parse the radiotap header
7149 * of injected frames.
7150 *
7151 * To accurately parse and take into account rate and retransmission fields,
7152 * you must initialize the chandef field in the ieee80211_tx_info structure
7153 * of the skb before calling this function.
7154 *
7155 * @skb: packet injected by userspace
7156 * @dev: the &struct device of this 802.11 device
7157 */
7158bool ieee80211_parse_tx_radiotap(struct sk_buff *skb,
7159 struct net_device *dev);
7160
7161/**
7162 * struct ieee80211_noa_data - holds temporary data for tracking P2P NoA state
7163 *
7164 * @next_tsf: TSF timestamp of the next absent state change
7165 * @has_next_tsf: next absent state change event pending
7166 *
7167 * @absent: descriptor bitmask, set if GO is currently absent
7168 *
7169 * private:
7170 *
7171 * @count: count fields from the NoA descriptors
7172 * @desc: adjusted data from the NoA
7173 */
7174struct ieee80211_noa_data {
7175 u32 next_tsf;
7176 bool has_next_tsf;
7177
7178 u8 absent;
7179
7180 u8 count[IEEE80211_P2P_NOA_DESC_MAX];
7181 struct {
7182 u32 start;
7183 u32 duration;
7184 u32 interval;
7185 } desc[IEEE80211_P2P_NOA_DESC_MAX];
7186};
7187
7188/**
7189 * ieee80211_parse_p2p_noa - initialize NoA tracking data from P2P IE
7190 *
7191 * @attr: P2P NoA IE
7192 * @data: NoA tracking data
7193 * @tsf: current TSF timestamp
7194 *
7195 * Return: number of successfully parsed descriptors
7196 */
7197int ieee80211_parse_p2p_noa(const struct ieee80211_p2p_noa_attr *attr,
7198 struct ieee80211_noa_data *data, u32 tsf);
7199
7200/**
7201 * ieee80211_update_p2p_noa - get next pending P2P GO absent state change
7202 *
7203 * @data: NoA tracking data
7204 * @tsf: current TSF timestamp
7205 */
7206void ieee80211_update_p2p_noa(struct ieee80211_noa_data *data, u32 tsf);
7207
7208/**
7209 * ieee80211_tdls_oper_request - request userspace to perform a TDLS operation
7210 * @vif: virtual interface
7211 * @peer: the peer's destination address
7212 * @oper: the requested TDLS operation
7213 * @reason_code: reason code for the operation, valid for TDLS teardown
7214 * @gfp: allocation flags
7215 *
7216 * See cfg80211_tdls_oper_request().
7217 */
7218void ieee80211_tdls_oper_request(struct ieee80211_vif *vif, const u8 *peer,
7219 enum nl80211_tdls_operation oper,
7220 u16 reason_code, gfp_t gfp);
7221
7222/**
7223 * ieee80211_reserve_tid - request to reserve a specific TID
7224 *
7225 * There is sometimes a need (such as in TDLS) for blocking the driver from
7226 * using a specific TID so that the FW can use it for certain operations such
7227 * as sending PTI requests. To make sure that the driver doesn't use that TID,
7228 * this function must be called as it flushes out packets on this TID and marks
7229 * it as blocked, so that any transmit for the station on this TID will be
7230 * redirected to the alternative TID in the same AC.
7231 *
7232 * Note that this function blocks and may call back into the driver, so it
7233 * should be called without driver locks held. Also note this function should
7234 * only be called from the driver's @sta_state callback.
7235 *
7236 * @sta: the station to reserve the TID for
7237 * @tid: the TID to reserve
7238 *
7239 * Returns: 0 on success, else on failure
7240 */
7241int ieee80211_reserve_tid(struct ieee80211_sta *sta, u8 tid);
7242
7243/**
7244 * ieee80211_unreserve_tid - request to unreserve a specific TID
7245 *
7246 * Once there is no longer any need for reserving a certain TID, this function
7247 * should be called, and no longer will packets have their TID modified for
7248 * preventing use of this TID in the driver.
7249 *
7250 * Note that this function blocks and acquires a lock, so it should be called
7251 * without driver locks held. Also note this function should only be called
7252 * from the driver's @sta_state callback.
7253 *
7254 * @sta: the station
7255 * @tid: the TID to unreserve
7256 */
7257void ieee80211_unreserve_tid(struct ieee80211_sta *sta, u8 tid);
7258
7259/**
7260 * ieee80211_tx_dequeue - dequeue a packet from a software tx queue
7261 *
7262 * @hw: pointer as obtained from ieee80211_alloc_hw()
7263 * @txq: pointer obtained from station or virtual interface, or from
7264 * ieee80211_next_txq()
7265 *
7266 * Returns the skb if successful, %NULL if no frame was available.
7267 *
7268 * Note that this must be called in an rcu_read_lock() critical section,
7269 * which can only be released after the SKB was handled. Some pointers in
7270 * skb->cb, e.g. the key pointer, are protected by RCU and thus the
7271 * critical section must persist not just for the duration of this call
7272 * but for the duration of the frame handling.
7273 * However, also note that while in the wake_tx_queue() method,
7274 * rcu_read_lock() is already held.
7275 *
7276 * softirqs must also be disabled when this function is called.
7277 * In process context, use ieee80211_tx_dequeue_ni() instead.
7278 */
7279struct sk_buff *ieee80211_tx_dequeue(struct ieee80211_hw *hw,
7280 struct ieee80211_txq *txq);
7281
7282/**
7283 * ieee80211_tx_dequeue_ni - dequeue a packet from a software tx queue
7284 * (in process context)
7285 *
7286 * Like ieee80211_tx_dequeue() but can be called in process context
7287 * (internally disables bottom halves).
7288 *
7289 * @hw: pointer as obtained from ieee80211_alloc_hw()
7290 * @txq: pointer obtained from station or virtual interface, or from
7291 * ieee80211_next_txq()
7292 */
7293static inline struct sk_buff *ieee80211_tx_dequeue_ni(struct ieee80211_hw *hw,
7294 struct ieee80211_txq *txq)
7295{
7296 struct sk_buff *skb;
7297
7298 local_bh_disable();
7299 skb = ieee80211_tx_dequeue(hw, txq);
7300 local_bh_enable();
7301
7302 return skb;
7303}
7304
7305/**
7306 * ieee80211_handle_wake_tx_queue - mac80211 handler for wake_tx_queue callback
7307 *
7308 * @hw: pointer as obtained from wake_tx_queue() callback().
7309 * @txq: pointer as obtained from wake_tx_queue() callback().
7310 *
7311 * Drivers can use this function for the mandatory mac80211 wake_tx_queue
7312 * callback in struct ieee80211_ops. They should not call this function.
7313 */
7314void ieee80211_handle_wake_tx_queue(struct ieee80211_hw *hw,
7315 struct ieee80211_txq *txq);
7316
7317/**
7318 * ieee80211_next_txq - get next tx queue to pull packets from
7319 *
7320 * @hw: pointer as obtained from ieee80211_alloc_hw()
7321 * @ac: AC number to return packets from.
7322 *
7323 * Returns the next txq if successful, %NULL if no queue is eligible. If a txq
7324 * is returned, it should be returned with ieee80211_return_txq() after the
7325 * driver has finished scheduling it.
7326 */
7327struct ieee80211_txq *ieee80211_next_txq(struct ieee80211_hw *hw, u8 ac);
7328
7329/**
7330 * ieee80211_txq_schedule_start - start new scheduling round for TXQs
7331 *
7332 * @hw: pointer as obtained from ieee80211_alloc_hw()
7333 * @ac: AC number to acquire locks for
7334 *
7335 * Should be called before ieee80211_next_txq() or ieee80211_return_txq().
7336 * The driver must not call multiple TXQ scheduling rounds concurrently.
7337 */
7338void ieee80211_txq_schedule_start(struct ieee80211_hw *hw, u8 ac);
7339
7340/* (deprecated) */
7341static inline void ieee80211_txq_schedule_end(struct ieee80211_hw *hw, u8 ac)
7342{
7343}
7344
7345void __ieee80211_schedule_txq(struct ieee80211_hw *hw,
7346 struct ieee80211_txq *txq, bool force);
7347
7348/**
7349 * ieee80211_schedule_txq - schedule a TXQ for transmission
7350 *
7351 * @hw: pointer as obtained from ieee80211_alloc_hw()
7352 * @txq: pointer obtained from station or virtual interface
7353 *
7354 * Schedules a TXQ for transmission if it is not already scheduled,
7355 * even if mac80211 does not have any packets buffered.
7356 *
7357 * The driver may call this function if it has buffered packets for
7358 * this TXQ internally.
7359 */
7360static inline void
7361ieee80211_schedule_txq(struct ieee80211_hw *hw, struct ieee80211_txq *txq)
7362{
7363 __ieee80211_schedule_txq(hw, txq, true);
7364}
7365
7366/**
7367 * ieee80211_return_txq - return a TXQ previously acquired by ieee80211_next_txq()
7368 *
7369 * @hw: pointer as obtained from ieee80211_alloc_hw()
7370 * @txq: pointer obtained from station or virtual interface
7371 * @force: schedule txq even if mac80211 does not have any buffered packets.
7372 *
7373 * The driver may set force=true if it has buffered packets for this TXQ
7374 * internally.
7375 */
7376static inline void
7377ieee80211_return_txq(struct ieee80211_hw *hw, struct ieee80211_txq *txq,
7378 bool force)
7379{
7380 __ieee80211_schedule_txq(hw, txq, force);
7381}
7382
7383/**
7384 * ieee80211_txq_may_transmit - check whether TXQ is allowed to transmit
7385 *
7386 * This function is used to check whether given txq is allowed to transmit by
7387 * the airtime scheduler, and can be used by drivers to access the airtime
7388 * fairness accounting without using the scheduling order enforced by
7389 * next_txq().
7390 *
7391 * Returns %true if the airtime scheduler thinks the TXQ should be allowed to
7392 * transmit, and %false if it should be throttled. This function can also have
7393 * the side effect of rotating the TXQ in the scheduler rotation, which will
7394 * eventually bring the deficit to positive and allow the station to transmit
7395 * again.
7396 *
7397 * The API ieee80211_txq_may_transmit() also ensures that TXQ list will be
7398 * aligned against driver's own round-robin scheduler list. i.e it rotates
7399 * the TXQ list till it makes the requested node becomes the first entry
7400 * in TXQ list. Thus both the TXQ list and driver's list are in sync. If this
7401 * function returns %true, the driver is expected to schedule packets
7402 * for transmission, and then return the TXQ through ieee80211_return_txq().
7403 *
7404 * @hw: pointer as obtained from ieee80211_alloc_hw()
7405 * @txq: pointer obtained from station or virtual interface
7406 */
7407bool ieee80211_txq_may_transmit(struct ieee80211_hw *hw,
7408 struct ieee80211_txq *txq);
7409
7410/**
7411 * ieee80211_txq_get_depth - get pending frame/byte count of given txq
7412 *
7413 * The values are not guaranteed to be coherent with regard to each other, i.e.
7414 * txq state can change half-way of this function and the caller may end up
7415 * with "new" frame_cnt and "old" byte_cnt or vice-versa.
7416 *
7417 * @txq: pointer obtained from station or virtual interface
7418 * @frame_cnt: pointer to store frame count
7419 * @byte_cnt: pointer to store byte count
7420 */
7421void ieee80211_txq_get_depth(struct ieee80211_txq *txq,
7422 unsigned long *frame_cnt,
7423 unsigned long *byte_cnt);
7424
7425/**
7426 * ieee80211_nan_func_terminated - notify about NAN function termination.
7427 *
7428 * This function is used to notify mac80211 about NAN function termination.
7429 * Note that this function can't be called from hard irq.
7430 *
7431 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
7432 * @inst_id: the local instance id
7433 * @reason: termination reason (one of the NL80211_NAN_FUNC_TERM_REASON_*)
7434 * @gfp: allocation flags
7435 */
7436void ieee80211_nan_func_terminated(struct ieee80211_vif *vif,
7437 u8 inst_id,
7438 enum nl80211_nan_func_term_reason reason,
7439 gfp_t gfp);
7440
7441/**
7442 * ieee80211_nan_func_match - notify about NAN function match event.
7443 *
7444 * This function is used to notify mac80211 about NAN function match. The
7445 * cookie inside the match struct will be assigned by mac80211.
7446 * Note that this function can't be called from hard irq.
7447 *
7448 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
7449 * @match: match event information
7450 * @gfp: allocation flags
7451 */
7452void ieee80211_nan_func_match(struct ieee80211_vif *vif,
7453 struct cfg80211_nan_match_params *match,
7454 gfp_t gfp);
7455
7456/**
7457 * ieee80211_calc_rx_airtime - calculate estimated transmission airtime for RX.
7458 *
7459 * This function calculates the estimated airtime usage of a frame based on the
7460 * rate information in the RX status struct and the frame length.
7461 *
7462 * @hw: pointer as obtained from ieee80211_alloc_hw()
7463 * @status: &struct ieee80211_rx_status containing the transmission rate
7464 * information.
7465 * @len: frame length in bytes
7466 */
7467u32 ieee80211_calc_rx_airtime(struct ieee80211_hw *hw,
7468 struct ieee80211_rx_status *status,
7469 int len);
7470
7471/**
7472 * ieee80211_calc_tx_airtime - calculate estimated transmission airtime for TX.
7473 *
7474 * This function calculates the estimated airtime usage of a frame based on the
7475 * rate information in the TX info struct and the frame length.
7476 *
7477 * @hw: pointer as obtained from ieee80211_alloc_hw()
7478 * @info: &struct ieee80211_tx_info of the frame.
7479 * @len: frame length in bytes
7480 */
7481u32 ieee80211_calc_tx_airtime(struct ieee80211_hw *hw,
7482 struct ieee80211_tx_info *info,
7483 int len);
7484/**
7485 * ieee80211_set_hw_80211_encap - enable hardware encapsulation offloading.
7486 *
7487 * This function is used to notify mac80211 that a vif can be passed raw 802.3
7488 * frames. The driver needs to then handle the 802.11 encapsulation inside the
7489 * hardware or firmware.
7490 *
7491 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
7492 * @enable: indicate if the feature should be turned on or off
7493 */
7494bool ieee80211_set_hw_80211_encap(struct ieee80211_vif *vif, bool enable);
7495
7496/**
7497 * ieee80211_get_fils_discovery_tmpl - Get FILS discovery template.
7498 * @hw: pointer obtained from ieee80211_alloc_hw().
7499 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
7500 *
7501 * The driver is responsible for freeing the returned skb.
7502 *
7503 * Return: FILS discovery template. %NULL on error.
7504 */
7505struct sk_buff *ieee80211_get_fils_discovery_tmpl(struct ieee80211_hw *hw,
7506 struct ieee80211_vif *vif);
7507
7508/**
7509 * ieee80211_get_unsol_bcast_probe_resp_tmpl - Get unsolicited broadcast
7510 * probe response template.
7511 * @hw: pointer obtained from ieee80211_alloc_hw().
7512 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
7513 *
7514 * The driver is responsible for freeing the returned skb.
7515 *
7516 * Return: Unsolicited broadcast probe response template. %NULL on error.
7517 */
7518struct sk_buff *
7519ieee80211_get_unsol_bcast_probe_resp_tmpl(struct ieee80211_hw *hw,
7520 struct ieee80211_vif *vif);
7521
7522/**
7523 * ieee80211_obss_color_collision_notify - notify userland about a BSS color
7524 * collision.
7525 *
7526 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
7527 * @color_bitmap: a 64 bit bitmap representing the colors that the local BSS is
7528 * aware of.
7529 */
7530void
7531ieee80211_obss_color_collision_notify(struct ieee80211_vif *vif,
7532 u64 color_bitmap);
7533
7534/**
7535 * ieee80211_is_tx_data - check if frame is a data frame
7536 *
7537 * The function is used to check if a frame is a data frame. Frames with
7538 * hardware encapsulation enabled are data frames.
7539 *
7540 * @skb: the frame to be transmitted.
7541 */
7542static inline bool ieee80211_is_tx_data(struct sk_buff *skb)
7543{
7544 struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
7545 struct ieee80211_hdr *hdr = (void *) skb->data;
7546
7547 return info->flags & IEEE80211_TX_CTL_HW_80211_ENCAP ||
7548 ieee80211_is_data(hdr->frame_control);
7549}
7550
7551/**
7552 * ieee80211_set_active_links - set active links in client mode
7553 * @vif: interface to set active links on
7554 * @active_links: the new active links bitmap
7555 *
7556 * Context: Must be called with wiphy mutex held; may sleep; calls
7557 * back into the driver.
7558 *
7559 * This changes the active links on an interface. The interface
7560 * must be in client mode (in AP mode, all links are always active),
7561 * and @active_links must be a subset of the vif's valid_links.
7562 *
7563 * If a link is switched off and another is switched on at the same
7564 * time (e.g. active_links going from 0x1 to 0x10) then you will get
7565 * a sequence of calls like
7566 *
7567 * - change_vif_links(0x11)
7568 * - unassign_vif_chanctx(link_id=0)
7569 * - change_sta_links(0x11) for each affected STA (the AP)
7570 * (TDLS connections on now inactive links should be torn down)
7571 * - remove group keys on the old link (link_id 0)
7572 * - add new group keys (GTK/IGTK/BIGTK) on the new link (link_id 4)
7573 * - change_sta_links(0x10) for each affected STA (the AP)
7574 * - assign_vif_chanctx(link_id=4)
7575 * - change_vif_links(0x10)
7576 */
7577int ieee80211_set_active_links(struct ieee80211_vif *vif, u16 active_links);
7578
7579/**
7580 * ieee80211_set_active_links_async - asynchronously set active links
7581 * @vif: interface to set active links on
7582 * @active_links: the new active links bitmap
7583 *
7584 * See ieee80211_set_active_links() for more information, the only
7585 * difference here is that the link change is triggered async and
7586 * can be called in any context, but the link switch will only be
7587 * completed after it returns.
7588 */
7589void ieee80211_set_active_links_async(struct ieee80211_vif *vif,
7590 u16 active_links);
7591
7592/* for older drivers - let's not document these ... */
7593int ieee80211_emulate_add_chanctx(struct ieee80211_hw *hw,
7594 struct ieee80211_chanctx_conf *ctx);
7595void ieee80211_emulate_remove_chanctx(struct ieee80211_hw *hw,
7596 struct ieee80211_chanctx_conf *ctx);
7597void ieee80211_emulate_change_chanctx(struct ieee80211_hw *hw,
7598 struct ieee80211_chanctx_conf *ctx,
7599 u32 changed);
7600int ieee80211_emulate_switch_vif_chanctx(struct ieee80211_hw *hw,
7601 struct ieee80211_vif_chanctx_switch *vifs,
7602 int n_vifs,
7603 enum ieee80211_chanctx_switch_mode mode);
7604
7605#endif /* MAC80211_H */