Loading...
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# PHY Layer Configuration
4#
5
6config PHYLINK
7 tristate
8 depends on NETDEVICES
9 select PHYLIB
10 select SWPHY
11 help
12 PHYlink models the link between the PHY and MAC, allowing fixed
13 configuration links, PHYs, and Serdes links with MAC level
14 autonegotiation modes.
15
16menuconfig PHYLIB
17 tristate "PHY Device support and infrastructure"
18 depends on NETDEVICES
19 select MDIO_DEVICE
20 select MDIO_DEVRES
21 help
22 Ethernet controllers are usually attached to PHY
23 devices. This option provides infrastructure for
24 managing PHY devices.
25
26if PHYLIB
27
28config SWPHY
29 bool
30
31config LED_TRIGGER_PHY
32 bool "Support LED triggers for tracking link state"
33 depends on LEDS_TRIGGERS
34 help
35 Adds support for a set of LED trigger events per-PHY. Link
36 state change will trigger the events, for consumption by an
37 LED class driver. There are triggers for each link speed currently
38 supported by the PHY and also a one common "link" trigger as a
39 logical-or of all the link speed ones.
40 All these triggers are named according to the following pattern:
41 <mii bus id>:<phy>:<speed>
42
43 Where speed is in the form:
44 <Speed in megabits>Mbps OR <Speed in gigabits>Gbps OR link
45 for any speed known to the PHY.
46
47config OPEN_ALLIANCE_HELPERS
48 bool
49
50config PHYLIB_LEDS
51 def_bool OF
52 depends on LEDS_CLASS=y || LEDS_CLASS=PHYLIB
53 help
54 When LED class support is enabled, phylib can automatically
55 probe LED setting from device tree.
56
57config FIXED_PHY
58 tristate "MDIO Bus/PHY emulation with fixed speed/link PHYs"
59 select SWPHY
60 help
61 Adds the platform "fixed" MDIO Bus to cover the boards that use
62 PHYs that are not connected to the real MDIO bus.
63
64 Currently tested with mpc866ads and mpc8349e-mitx.
65
66config RUST_PHYLIB_ABSTRACTIONS
67 bool "Rust PHYLIB abstractions support"
68 depends on RUST
69 depends on PHYLIB=y
70 help
71 Adds support needed for PHY drivers written in Rust. It provides
72 a wrapper around the C phylib core.
73
74config SFP
75 tristate "SFP cage support"
76 depends on I2C && PHYLINK
77 depends on HWMON || HWMON=n
78 select MDIO_I2C
79
80comment "MII PHY device drivers"
81
82config AIR_EN8811H_PHY
83 tristate "Airoha EN8811H 2.5 Gigabit PHY"
84 help
85 Currently supports the Airoha EN8811H PHY.
86
87config AMD_PHY
88 tristate "AMD and Altima PHYs"
89 help
90 Currently supports the AMD am79c874 and Altima AC101L.
91
92config MESON_GXL_PHY
93 tristate "Amlogic Meson GXL Internal PHY"
94 depends on ARCH_MESON || COMPILE_TEST
95 select SMSC_PHY
96 help
97 Currently has a driver for the Amlogic Meson GXL Internal PHY
98
99config ADIN_PHY
100 tristate "Analog Devices Industrial Ethernet PHYs"
101 help
102 Adds support for the Analog Devices Industrial Ethernet PHYs.
103 Currently supports the:
104 - ADIN1200 - Robust,Industrial, Low Power 10/100 Ethernet PHY
105 - ADIN1300 - Robust,Industrial, Low Latency 10/100/1000 Gigabit
106 Ethernet PHY
107
108config ADIN1100_PHY
109 tristate "Analog Devices Industrial Ethernet T1L PHYs"
110 help
111 Adds support for the Analog Devices Industrial T1L Ethernet PHYs.
112 Currently supports the:
113 - ADIN1100 - Robust,Industrial, Low Power 10BASE-T1L Ethernet PHY
114
115config AMCC_QT2025_PHY
116 tristate "AMCC QT2025 PHY"
117 depends on RUST_PHYLIB_ABSTRACTIONS
118 depends on RUST_FW_LOADER_ABSTRACTIONS
119 help
120 Adds support for the Applied Micro Circuits Corporation QT2025 PHY.
121
122source "drivers/net/phy/aquantia/Kconfig"
123
124config AX88796B_PHY
125 tristate "Asix PHYs"
126 help
127 Currently supports the Asix Electronics PHY found in the X-Surf 100
128 AX88796B package.
129
130config AX88796B_RUST_PHY
131 bool "Rust reference driver for Asix PHYs"
132 depends on RUST_PHYLIB_ABSTRACTIONS && AX88796B_PHY
133 help
134 Uses the Rust reference driver for Asix PHYs (ax88796b_rust.ko).
135 The features are equivalent. It supports the Asix Electronics PHY
136 found in the X-Surf 100 AX88796B package.
137
138config BROADCOM_PHY
139 tristate "Broadcom 54XX PHYs"
140 select BCM_NET_PHYLIB
141 select BCM_NET_PHYPTP if NETWORK_PHY_TIMESTAMPING
142 depends on PTP_1588_CLOCK_OPTIONAL
143 help
144 Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
145 BCM5481, BCM54810 and BCM5482 PHYs.
146
147config BCM54140_PHY
148 tristate "Broadcom BCM54140 PHY"
149 depends on HWMON || HWMON=n
150 select BCM_NET_PHYLIB
151 help
152 Support the Broadcom BCM54140 Quad SGMII/QSGMII PHY.
153
154 This driver also supports the hardware monitoring of this PHY and
155 exposes voltage and temperature sensors.
156
157config BCM63XX_PHY
158 tristate "Broadcom 63xx SOCs internal PHY"
159 depends on BCM63XX || COMPILE_TEST
160 select BCM_NET_PHYLIB
161 help
162 Currently supports the 6348 and 6358 PHYs.
163
164config BCM7XXX_PHY
165 tristate "Broadcom 7xxx SOCs internal PHYs"
166 select BCM_NET_PHYLIB
167 help
168 Currently supports the BCM7366, BCM7439, BCM7445, and
169 40nm and 65nm generation of BCM7xxx Set Top Box SoCs.
170
171config BCM84881_PHY
172 tristate "Broadcom BCM84881 PHY"
173 help
174 Support the Broadcom BCM84881 PHY.
175
176config BCM87XX_PHY
177 tristate "Broadcom BCM8706 and BCM8727 PHYs"
178 help
179 Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs.
180
181config BCM_CYGNUS_PHY
182 tristate "Broadcom Cygnus/Omega SoC internal PHY"
183 depends on ARCH_BCM_IPROC || COMPILE_TEST
184 depends on MDIO_BCM_IPROC
185 select BCM_NET_PHYLIB
186 help
187 This PHY driver is for the 1G internal PHYs of the Broadcom
188 Cygnus and Omega Family SoC.
189
190 Currently supports internal PHY's used in the BCM11300,
191 BCM11320, BCM11350, BCM11360, BCM58300, BCM58302,
192 BCM58303 & BCM58305 Broadcom Cygnus SoCs.
193
194config BCM_NET_PHYLIB
195 tristate
196
197config BCM_NET_PHYPTP
198 tristate
199
200config CICADA_PHY
201 tristate "Cicada PHYs"
202 help
203 Currently supports the cis8204
204
205config CORTINA_PHY
206 tristate "Cortina EDC CDR 10G Ethernet PHY"
207 help
208 Currently supports the CS4340 phy.
209
210config DAVICOM_PHY
211 tristate "Davicom PHYs"
212 help
213 Currently supports dm9161e and dm9131
214
215config ICPLUS_PHY
216 tristate "ICPlus PHYs"
217 help
218 Currently supports the IP175C and IP1001 PHYs.
219
220config LXT_PHY
221 tristate "Intel LXT PHYs"
222 help
223 Currently supports the lxt970, lxt971
224
225config INTEL_XWAY_PHY
226 tristate "Intel XWAY PHYs"
227 help
228 Supports the Intel XWAY (former Lantiq) 11G and 22E PHYs.
229 These PHYs are marked as standalone chips under the names
230 PEF 7061, PEF 7071 and PEF 7072 or integrated into the Intel
231 SoCs xRX200, xRX300, xRX330, xRX350 and xRX550.
232
233config LSI_ET1011C_PHY
234 tristate "LSI ET1011C PHY"
235 help
236 Supports the LSI ET1011C PHY.
237
238config MARVELL_PHY
239 tristate "Marvell Alaska PHYs"
240 help
241 Currently has a driver for the 88E1XXX
242
243config MARVELL_10G_PHY
244 tristate "Marvell Alaska 10Gbit PHYs"
245 help
246 Support for the Marvell Alaska MV88X3310 and compatible PHYs.
247
248config MARVELL_88Q2XXX_PHY
249 tristate "Marvell 88Q2XXX PHY"
250 depends on HWMON || HWMON=n
251 help
252 Support for the Marvell 88Q2XXX 100/1000BASE-T1 Automotive Ethernet
253 PHYs.
254
255config MARVELL_88X2222_PHY
256 tristate "Marvell 88X2222 PHY"
257 help
258 Support for the Marvell 88X2222 Dual-port Multi-speed Ethernet
259 Transceiver.
260
261config MAXLINEAR_GPHY
262 tristate "Maxlinear Ethernet PHYs"
263 select POLYNOMIAL if HWMON
264 depends on HWMON || HWMON=n
265 help
266 Support for the Maxlinear GPY115, GPY211, GPY212, GPY215,
267 GPY241, GPY245 PHYs.
268
269source "drivers/net/phy/mediatek/Kconfig"
270
271config MICREL_PHY
272 tristate "Micrel PHYs"
273 depends on PTP_1588_CLOCK_OPTIONAL
274 help
275 Supports the KSZ9021, VSC8201, KS8001 PHYs.
276
277config MICROCHIP_T1S_PHY
278 tristate "Microchip 10BASE-T1S Ethernet PHYs"
279 help
280 Currently supports the LAN8670/1/2 Rev.B1/C1/C2 and
281 LAN8650/1 Rev.B0/B1 Internal PHYs.
282
283config MICROCHIP_PHY
284 tristate "Microchip PHYs"
285 help
286 Supports the LAN88XX PHYs.
287
288config MICROCHIP_T1_PHY
289 tristate "Microchip T1 PHYs"
290 help
291 Supports the LAN87XX PHYs.
292
293config MICROSEMI_PHY
294 tristate "Microsemi PHYs"
295 depends on MACSEC || MACSEC=n
296 depends on PTP_1588_CLOCK_OPTIONAL || !NETWORK_PHY_TIMESTAMPING
297 select CRYPTO_LIB_AES if MACSEC
298 help
299 Currently supports VSC8514, VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
300
301config MOTORCOMM_PHY
302 tristate "Motorcomm PHYs"
303 help
304 Enables support for Motorcomm network PHYs.
305 Currently supports YT85xx Gigabit Ethernet PHYs.
306
307config NATIONAL_PHY
308 tristate "National Semiconductor PHYs"
309 help
310 Currently supports the DP83865 PHY.
311
312config NXP_CBTX_PHY
313 tristate "NXP 100BASE-TX PHYs"
314 help
315 Support the 100BASE-TX PHY integrated on the SJA1110 automotive
316 switch family.
317
318config NXP_C45_TJA11XX_PHY
319 tristate "NXP C45 TJA11XX PHYs"
320 depends on PTP_1588_CLOCK_OPTIONAL
321 depends on MACSEC || !MACSEC
322 help
323 Enable support for NXP C45 TJA11XX PHYs.
324 Currently supports the TJA1103, TJA1104 and TJA1120 PHYs.
325
326config NXP_TJA11XX_PHY
327 tristate "NXP TJA11xx PHYs support"
328 depends on HWMON
329 help
330 Currently supports the NXP TJA1100 and TJA1101 PHY.
331
332config NCN26000_PHY
333 tristate "Onsemi 10BASE-T1S Ethernet PHY"
334 help
335 Adds support for the onsemi 10BASE-T1S Ethernet PHY.
336 Currently supports the NCN26000 10BASE-T1S Industrial PHY
337 with MII interface.
338
339source "drivers/net/phy/qcom/Kconfig"
340
341config QSEMI_PHY
342 tristate "Quality Semiconductor PHYs"
343 help
344 Currently supports the qs6612
345
346config REALTEK_PHY
347 tristate "Realtek PHYs"
348 help
349 Supports the Realtek 821x PHY.
350
351config RENESAS_PHY
352 tristate "Renesas PHYs"
353 help
354 Supports the Renesas PHYs uPD60620 and uPD60620A.
355
356config ROCKCHIP_PHY
357 tristate "Rockchip Ethernet PHYs"
358 help
359 Currently supports the integrated Ethernet PHY.
360
361config SMSC_PHY
362 tristate "SMSC PHYs"
363 select CRC16
364 help
365 Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs
366
367config STE10XP
368 tristate "STMicroelectronics STe10Xp PHYs"
369 help
370 This is the driver for the STe100p and STe101p PHYs.
371
372config TERANETICS_PHY
373 tristate "Teranetics PHYs"
374 help
375 Currently supports the Teranetics TN2020
376
377config DP83822_PHY
378 tristate "Texas Instruments DP83822/825/826 PHYs"
379 help
380 Supports the DP83822, DP83825I, DP83825CM, DP83825CS, DP83825S,
381 DP83826C and DP83826NC PHYs.
382
383config DP83TC811_PHY
384 tristate "Texas Instruments DP83TC811 PHY"
385 help
386 Supports the DP83TC811 PHY.
387
388config DP83848_PHY
389 tristate "Texas Instruments DP83848 PHY"
390 help
391 Supports the DP83848 PHY.
392
393config DP83867_PHY
394 tristate "Texas Instruments DP83867 Gigabit PHY"
395 help
396 Currently supports the DP83867 PHY.
397
398config DP83869_PHY
399 tristate "Texas Instruments DP83869 Gigabit PHY"
400 help
401 Currently supports the DP83869 PHY. This PHY supports copper and
402 fiber connections.
403
404config DP83TD510_PHY
405 tristate "Texas Instruments DP83TD510 Ethernet 10Base-T1L PHY"
406 help
407 Support for the DP83TD510 Ethernet 10Base-T1L PHY. This PHY supports
408 a 10M single pair Ethernet connection for up to 1000 meter cable.
409
410config DP83TG720_PHY
411 tristate "Texas Instruments DP83TG720 Ethernet 1000Base-T1 PHY"
412 select OPEN_ALLIANCE_HELPERS
413 help
414 The DP83TG720S-Q1 is an automotive Ethernet physical layer
415 transceiver compliant with IEEE 802.3bp and Open Alliance
416 standards. It supports key functions necessary for
417 transmitting and receiving data over both unshielded and
418 shielded single twisted-pair cables. This device offers
419 flexible xMII interface options, including support for both
420 RGMII and SGMII MAC interfaces. It's suitable for applications
421 requiring high-speed data transmission in automotive
422 networking environments.
423
424config VITESSE_PHY
425 tristate "Vitesse PHYs"
426 help
427 Currently supports the vsc8244
428
429config XILINX_GMII2RGMII
430 tristate "Xilinx GMII2RGMII converter driver"
431 help
432 This driver support xilinx GMII to RGMII IP core it provides
433 the Reduced Gigabit Media Independent Interface(RGMII) between
434 Ethernet physical media devices and the Gigabit Ethernet controller.
435
436endif # PHYLIB
437
438config MICREL_KS8995MA
439 tristate "Micrel KS8995MA 5-ports 10/100 managed Ethernet switch"
440 depends on SPI
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# PHY Layer Configuration
4#
5
6menuconfig MDIO_DEVICE
7 tristate "MDIO bus device drivers"
8 help
9 MDIO devices and driver infrastructure code.
10
11if MDIO_DEVICE
12
13config MDIO_BUS
14 tristate
15 default m if PHYLIB=m
16 default MDIO_DEVICE
17 help
18 This internal symbol is used for link time dependencies and it
19 reflects whether the mdio_bus/mdio_device code is built as a
20 loadable module or built-in.
21
22if MDIO_BUS
23
24config MDIO_ASPEED
25 tristate "ASPEED MDIO bus controller"
26 depends on ARCH_ASPEED || COMPILE_TEST
27 depends on OF_MDIO && HAS_IOMEM
28 help
29 This module provides a driver for the independent MDIO bus
30 controllers found in the ASPEED AST2600 SoC. This is a driver for the
31 third revision of the ASPEED MDIO register interface - the first two
32 revisions are the "old" and "new" interfaces found in the AST2400 and
33 AST2500, embedded in the MAC. For legacy reasons, FTGMAC100 driver
34 continues to drive the embedded MDIO controller for the AST2400 and
35 AST2500 SoCs, so say N if AST2600 support is not required.
36
37config MDIO_BCM_IPROC
38 tristate "Broadcom iProc MDIO bus controller"
39 depends on ARCH_BCM_IPROC || COMPILE_TEST
40 depends on HAS_IOMEM && OF_MDIO
41 help
42 This module provides a driver for the MDIO busses found in the
43 Broadcom iProc SoC's.
44
45config MDIO_BCM_UNIMAC
46 tristate "Broadcom UniMAC MDIO bus controller"
47 depends on HAS_IOMEM
48 help
49 This module provides a driver for the Broadcom UniMAC MDIO busses.
50 This hardware can be found in the Broadcom GENET Ethernet MAC
51 controllers as well as some Broadcom Ethernet switches such as the
52 Starfighter 2 switches.
53
54config MDIO_BITBANG
55 tristate "Bitbanged MDIO buses"
56 help
57 This module implements the MDIO bus protocol in software,
58 for use by low level drivers that export the ability to
59 drive the relevant pins.
60
61 If in doubt, say N.
62
63config MDIO_BUS_MUX
64 tristate
65 depends on OF_MDIO
66 help
67 This module provides a driver framework for MDIO bus
68 multiplexers which connect one of several child MDIO busses
69 to a parent bus. Switching between child busses is done by
70 device specific drivers.
71
72config MDIO_BUS_MUX_BCM_IPROC
73 tristate "Broadcom iProc based MDIO bus multiplexers"
74 depends on OF && OF_MDIO && (ARCH_BCM_IPROC || COMPILE_TEST)
75 select MDIO_BUS_MUX
76 default ARCH_BCM_IPROC
77 help
78 This module provides a driver for MDIO bus multiplexers found in
79 iProc based Broadcom SoCs. This multiplexer connects one of several
80 child MDIO bus to a parent bus. Buses could be internal as well as
81 external and selection logic lies inside the same multiplexer.
82
83config MDIO_BUS_MUX_GPIO
84 tristate "GPIO controlled MDIO bus multiplexers"
85 depends on OF_GPIO && OF_MDIO
86 select MDIO_BUS_MUX
87 help
88 This module provides a driver for MDIO bus multiplexers that
89 are controlled via GPIO lines. The multiplexer connects one of
90 several child MDIO busses to a parent bus. Child bus
91 selection is under the control of GPIO lines.
92
93config MDIO_BUS_MUX_MESON_G12A
94 tristate "Amlogic G12a based MDIO bus multiplexer"
95 depends on ARCH_MESON || COMPILE_TEST
96 depends on OF_MDIO && HAS_IOMEM && COMMON_CLK
97 select MDIO_BUS_MUX
98 default m if ARCH_MESON
99 help
100 This module provides a driver for the MDIO multiplexer/glue of
101 the amlogic g12a SoC. The multiplexers connects either the external
102 or the internal MDIO bus to the parent bus.
103
104config MDIO_BUS_MUX_MMIOREG
105 tristate "MMIO device-controlled MDIO bus multiplexers"
106 depends on OF_MDIO && HAS_IOMEM
107 select MDIO_BUS_MUX
108 help
109 This module provides a driver for MDIO bus multiplexers that
110 are controlled via a simple memory-mapped device, like an FPGA.
111 The multiplexer connects one of several child MDIO busses to a
112 parent bus. Child bus selection is under the control of one of
113 the FPGA's registers.
114
115 Currently, only 8/16/32 bits registers are supported.
116
117config MDIO_BUS_MUX_MULTIPLEXER
118 tristate "MDIO bus multiplexer using kernel multiplexer subsystem"
119 depends on OF_MDIO
120 select MULTIPLEXER
121 select MDIO_BUS_MUX
122 help
123 This module provides a driver for MDIO bus multiplexer
124 that is controlled via the kernel multiplexer subsystem. The
125 bus multiplexer connects one of several child MDIO busses to
126 a parent bus. Child bus selection is under the control of
127 the kernel multiplexer subsystem.
128
129config MDIO_CAVIUM
130 tristate
131
132config MDIO_GPIO
133 tristate "GPIO lib-based bitbanged MDIO buses"
134 depends on MDIO_BITBANG
135 depends on GPIOLIB || COMPILE_TEST
136 ---help---
137 Supports GPIO lib-based MDIO busses.
138
139 To compile this driver as a module, choose M here: the module
140 will be called mdio-gpio.
141
142config MDIO_HISI_FEMAC
143 tristate "Hisilicon FEMAC MDIO bus controller"
144 depends on HAS_IOMEM && OF_MDIO
145 help
146 This module provides a driver for the MDIO busses found in the
147 Hisilicon SoC that have an Fast Ethernet MAC.
148
149config MDIO_I2C
150 tristate
151 depends on I2C
152 help
153 Support I2C based PHYs. This provides a MDIO bus bridged
154 to I2C to allow PHYs connected in I2C mode to be accessed
155 using the existing infrastructure.
156
157 This is library mode.
158
159config MDIO_MOXART
160 tristate "MOXA ART MDIO interface support"
161 depends on ARCH_MOXART || COMPILE_TEST
162 help
163 This driver supports the MDIO interface found in the network
164 interface units of the MOXA ART SoC
165
166config MDIO_MSCC_MIIM
167 tristate "Microsemi MIIM interface support"
168 depends on HAS_IOMEM
169 help
170 This driver supports the MIIM (MDIO) interface found in the network
171 switches of the Microsemi SoCs
172
173config MDIO_OCTEON
174 tristate "Octeon and some ThunderX SOCs MDIO buses"
175 depends on (64BIT && OF_MDIO) || COMPILE_TEST
176 depends on HAS_IOMEM
177 select MDIO_CAVIUM
178 help
179 This module provides a driver for the Octeon and ThunderX MDIO
180 buses. It is required by the Octeon and ThunderX ethernet device
181 drivers on some systems.
182
183config MDIO_SUN4I
184 tristate "Allwinner sun4i MDIO interface support"
185 depends on ARCH_SUNXI || COMPILE_TEST
186 help
187 This driver supports the MDIO interface found in the network
188 interface units of the Allwinner SoC that have an EMAC (A10,
189 A12, A10s, etc.)
190
191config MDIO_THUNDER
192 tristate "ThunderX SOCs MDIO buses"
193 depends on 64BIT
194 depends on PCI
195 select MDIO_CAVIUM
196 help
197 This driver supports the MDIO interfaces found on Cavium
198 ThunderX SoCs when the MDIO bus device appears as a PCI
199 device.
200
201config MDIO_XGENE
202 tristate "APM X-Gene SoC MDIO bus controller"
203 depends on ARCH_XGENE || COMPILE_TEST
204 help
205 This module provides a driver for the MDIO busses found in the
206 APM X-Gene SoC's.
207
208endif
209endif
210
211config PHYLINK
212 tristate
213 depends on NETDEVICES
214 select PHYLIB
215 select SWPHY
216 help
217 PHYlink models the link between the PHY and MAC, allowing fixed
218 configuration links, PHYs, and Serdes links with MAC level
219 autonegotiation modes.
220
221menuconfig PHYLIB
222 tristate "PHY Device support and infrastructure"
223 depends on NETDEVICES
224 select MDIO_DEVICE
225 help
226 Ethernet controllers are usually attached to PHY
227 devices. This option provides infrastructure for
228 managing PHY devices.
229
230if PHYLIB
231
232config SWPHY
233 bool
234
235config LED_TRIGGER_PHY
236 bool "Support LED triggers for tracking link state"
237 depends on LEDS_TRIGGERS
238 ---help---
239 Adds support for a set of LED trigger events per-PHY. Link
240 state change will trigger the events, for consumption by an
241 LED class driver. There are triggers for each link speed currently
242 supported by the PHY and also a one common "link" trigger as a
243 logical-or of all the link speed ones.
244 All these triggers are named according to the following pattern:
245 <mii bus id>:<phy>:<speed>
246
247 Where speed is in the form:
248 <Speed in megabits>Mbps OR <Speed in gigabits>Gbps OR link
249 for any speed known to the PHY.
250
251
252comment "MII PHY device drivers"
253
254config SFP
255 tristate "SFP cage support"
256 depends on I2C && PHYLINK
257 depends on HWMON || HWMON=n
258 select MDIO_I2C
259
260config ADIN_PHY
261 tristate "Analog Devices Industrial Ethernet PHYs"
262 help
263 Adds support for the Analog Devices Industrial Ethernet PHYs.
264 Currently supports the:
265 - ADIN1200 - Robust,Industrial, Low Power 10/100 Ethernet PHY
266 - ADIN1300 - Robust,Industrial, Low Latency 10/100/1000 Gigabit
267 Ethernet PHY
268
269config AMD_PHY
270 tristate "AMD PHYs"
271 ---help---
272 Currently supports the am79c874
273
274config AQUANTIA_PHY
275 tristate "Aquantia PHYs"
276 ---help---
277 Currently supports the Aquantia AQ1202, AQ2104, AQR105, AQR405
278
279config AX88796B_PHY
280 tristate "Asix PHYs"
281 help
282 Currently supports the Asix Electronics PHY found in the X-Surf 100
283 AX88796B package.
284
285config AT803X_PHY
286 tristate "AT803X PHYs"
287 ---help---
288 Currently supports the AT8030 and AT8035 model
289
290config BCM63XX_PHY
291 tristate "Broadcom 63xx SOCs internal PHY"
292 depends on BCM63XX || COMPILE_TEST
293 select BCM_NET_PHYLIB
294 ---help---
295 Currently supports the 6348 and 6358 PHYs.
296
297config BCM7XXX_PHY
298 tristate "Broadcom 7xxx SOCs internal PHYs"
299 select BCM_NET_PHYLIB
300 ---help---
301 Currently supports the BCM7366, BCM7439, BCM7445, and
302 40nm and 65nm generation of BCM7xxx Set Top Box SoCs.
303
304config BCM87XX_PHY
305 tristate "Broadcom BCM8706 and BCM8727 PHYs"
306 help
307 Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs.
308
309config BCM_CYGNUS_PHY
310 tristate "Broadcom Cygnus/Omega SoC internal PHY"
311 depends on ARCH_BCM_IPROC || COMPILE_TEST
312 depends on MDIO_BCM_IPROC
313 select BCM_NET_PHYLIB
314 ---help---
315 This PHY driver is for the 1G internal PHYs of the Broadcom
316 Cygnus and Omega Family SoC.
317
318 Currently supports internal PHY's used in the BCM11300,
319 BCM11320, BCM11350, BCM11360, BCM58300, BCM58302,
320 BCM58303 & BCM58305 Broadcom Cygnus SoCs.
321
322config BCM_NET_PHYLIB
323 tristate
324
325config BROADCOM_PHY
326 tristate "Broadcom PHYs"
327 select BCM_NET_PHYLIB
328 ---help---
329 Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
330 BCM5481, BCM54810 and BCM5482 PHYs.
331
332config CICADA_PHY
333 tristate "Cicada PHYs"
334 ---help---
335 Currently supports the cis8204
336
337config CORTINA_PHY
338 tristate "Cortina EDC CDR 10G Ethernet PHY"
339 ---help---
340 Currently supports the CS4340 phy.
341
342config DAVICOM_PHY
343 tristate "Davicom PHYs"
344 ---help---
345 Currently supports dm9161e and dm9131
346
347config DP83822_PHY
348 tristate "Texas Instruments DP83822 PHY"
349 ---help---
350 Supports the DP83822 PHY.
351
352config DP83TC811_PHY
353 tristate "Texas Instruments DP83TC822 PHY"
354 ---help---
355 Supports the DP83TC822 PHY.
356
357config DP83848_PHY
358 tristate "Texas Instruments DP83848 PHY"
359 ---help---
360 Supports the DP83848 PHY.
361
362config DP83867_PHY
363 tristate "Texas Instruments DP83867 Gigabit PHY"
364 ---help---
365 Currently supports the DP83867 PHY.
366
367config FIXED_PHY
368 tristate "MDIO Bus/PHY emulation with fixed speed/link PHYs"
369 depends on PHYLIB
370 select SWPHY
371 ---help---
372 Adds the platform "fixed" MDIO Bus to cover the boards that use
373 PHYs that are not connected to the real MDIO bus.
374
375 Currently tested with mpc866ads and mpc8349e-mitx.
376
377config ICPLUS_PHY
378 tristate "ICPlus PHYs"
379 ---help---
380 Currently supports the IP175C and IP1001 PHYs.
381
382config INTEL_XWAY_PHY
383 tristate "Intel XWAY PHYs"
384 ---help---
385 Supports the Intel XWAY (former Lantiq) 11G and 22E PHYs.
386 These PHYs are marked as standalone chips under the names
387 PEF 7061, PEF 7071 and PEF 7072 or integrated into the Intel
388 SoCs xRX200, xRX300, xRX330, xRX350 and xRX550.
389
390config LSI_ET1011C_PHY
391 tristate "LSI ET1011C PHY"
392 ---help---
393 Supports the LSI ET1011C PHY.
394
395config LXT_PHY
396 tristate "Intel LXT PHYs"
397 ---help---
398 Currently supports the lxt970, lxt971
399
400config MARVELL_PHY
401 tristate "Marvell PHYs"
402 ---help---
403 Currently has a driver for the 88E1011S
404
405config MARVELL_10G_PHY
406 tristate "Marvell Alaska 10Gbit PHYs"
407 ---help---
408 Support for the Marvell Alaska MV88X3310 and compatible PHYs.
409
410config MESON_GXL_PHY
411 tristate "Amlogic Meson GXL Internal PHY"
412 depends on ARCH_MESON || COMPILE_TEST
413 ---help---
414 Currently has a driver for the Amlogic Meson GXL Internal PHY
415
416config MICREL_PHY
417 tristate "Micrel PHYs"
418 ---help---
419 Supports the KSZ9021, VSC8201, KS8001 PHYs.
420
421config MICROCHIP_PHY
422 tristate "Microchip PHYs"
423 help
424 Supports the LAN88XX PHYs.
425
426config MICROCHIP_T1_PHY
427 tristate "Microchip T1 PHYs"
428 ---help---
429 Supports the LAN87XX PHYs.
430
431config MICROSEMI_PHY
432 tristate "Microsemi PHYs"
433 ---help---
434 Currently supports VSC8514, VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
435
436config NATIONAL_PHY
437 tristate "National Semiconductor PHYs"
438 ---help---
439 Currently supports the DP83865 PHY.
440
441config NXP_TJA11XX_PHY
442 tristate "NXP TJA11xx PHYs support"
443 depends on HWMON
444 ---help---
445 Currently supports the NXP TJA1100 and TJA1101 PHY.
446
447config QSEMI_PHY
448 tristate "Quality Semiconductor PHYs"
449 ---help---
450 Currently supports the qs6612
451
452config REALTEK_PHY
453 tristate "Realtek PHYs"
454 ---help---
455 Supports the Realtek 821x PHY.
456
457config RENESAS_PHY
458 tristate "Driver for Renesas PHYs"
459 ---help---
460 Supports the Renesas PHYs uPD60620 and uPD60620A.
461
462config ROCKCHIP_PHY
463 tristate "Driver for Rockchip Ethernet PHYs"
464 ---help---
465 Currently supports the integrated Ethernet PHY.
466
467config SMSC_PHY
468 tristate "SMSC PHYs"
469 ---help---
470 Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs
471
472config STE10XP
473 tristate "STMicroelectronics STe10Xp PHYs"
474 ---help---
475 This is the driver for the STe100p and STe101p PHYs.
476
477config TERANETICS_PHY
478 tristate "Teranetics PHYs"
479 ---help---
480 Currently supports the Teranetics TN2020
481
482config VITESSE_PHY
483 tristate "Vitesse PHYs"
484 ---help---
485 Currently supports the vsc8244
486
487config XILINX_GMII2RGMII
488 tristate "Xilinx GMII2RGMII converter driver"
489 ---help---
490 This driver support xilinx GMII to RGMII IP core it provides
491 the Reduced Gigabit Media Independent Interface(RGMII) between
492 Ethernet physical media devices and the Gigabit Ethernet controller.
493
494endif # PHYLIB
495
496config MICREL_KS8995MA
497 tristate "Micrel KS8995MA 5-ports 10/100 managed Ethernet switch"
498 depends on SPI