Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Libata driver for the highpoint 366 and 368 UDMA66 ATA controllers.
4 *
5 * This driver is heavily based upon:
6 *
7 * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003
8 *
9 * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
10 * Portions Copyright (C) 2001 Sun Microsystems, Inc.
11 * Portions Copyright (C) 2003 Red Hat Inc
12 *
13 *
14 * TODO
15 * Look into engine reset on timeout errors. Should not be required.
16 */
17#include <linux/kernel.h>
18#include <linux/module.h>
19#include <linux/pci.h>
20#include <linux/blkdev.h>
21#include <linux/delay.h>
22#include <scsi/scsi_host.h>
23#include <linux/libata.h>
24
25#define DRV_NAME "pata_hpt366"
26#define DRV_VERSION "0.6.13"
27
28struct hpt_clock {
29 u8 xfer_mode;
30 u32 timing;
31};
32
33/* key for bus clock timings
34 * bit
35 * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
36 * cycles = value + 1
37 * 4:7 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
38 * cycles = value + 1
39 * 8:11 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
40 * register access.
41 * 12:15 cmd_low_time. Active time of DIOW_/DIOR_ during task file
42 * register access.
43 * 16:18 udma_cycle_time. Clock cycles for UDMA xfer?
44 * 19:21 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
45 * 22:24 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
46 * register access.
47 * 28 UDMA enable.
48 * 29 DMA enable.
49 * 30 PIO_MST enable. If set, the chip is in bus master mode during
50 * PIO xfer.
51 * 31 FIFO enable.
52 */
53
54static const struct hpt_clock hpt366_40[] = {
55 { XFER_UDMA_4, 0x900fd943 },
56 { XFER_UDMA_3, 0x900ad943 },
57 { XFER_UDMA_2, 0x900bd943 },
58 { XFER_UDMA_1, 0x9008d943 },
59 { XFER_UDMA_0, 0x9008d943 },
60
61 { XFER_MW_DMA_2, 0xa008d943 },
62 { XFER_MW_DMA_1, 0xa010d955 },
63 { XFER_MW_DMA_0, 0xa010d9fc },
64
65 { XFER_PIO_4, 0xc008d963 },
66 { XFER_PIO_3, 0xc010d974 },
67 { XFER_PIO_2, 0xc010d997 },
68 { XFER_PIO_1, 0xc010d9c7 },
69 { XFER_PIO_0, 0xc018d9d9 },
70 { 0, 0x0120d9d9 }
71};
72
73static const struct hpt_clock hpt366_33[] = {
74 { XFER_UDMA_4, 0x90c9a731 },
75 { XFER_UDMA_3, 0x90cfa731 },
76 { XFER_UDMA_2, 0x90caa731 },
77 { XFER_UDMA_1, 0x90cba731 },
78 { XFER_UDMA_0, 0x90c8a731 },
79
80 { XFER_MW_DMA_2, 0xa0c8a731 },
81 { XFER_MW_DMA_1, 0xa0c8a732 }, /* 0xa0c8a733 */
82 { XFER_MW_DMA_0, 0xa0c8a797 },
83
84 { XFER_PIO_4, 0xc0c8a731 },
85 { XFER_PIO_3, 0xc0c8a742 },
86 { XFER_PIO_2, 0xc0d0a753 },
87 { XFER_PIO_1, 0xc0d0a7a3 }, /* 0xc0d0a793 */
88 { XFER_PIO_0, 0xc0d0a7aa }, /* 0xc0d0a7a7 */
89 { 0, 0x0120a7a7 }
90};
91
92static const struct hpt_clock hpt366_25[] = {
93 { XFER_UDMA_4, 0x90c98521 },
94 { XFER_UDMA_3, 0x90cf8521 },
95 { XFER_UDMA_2, 0x90cf8521 },
96 { XFER_UDMA_1, 0x90cb8521 },
97 { XFER_UDMA_0, 0x90cb8521 },
98
99 { XFER_MW_DMA_2, 0xa0ca8521 },
100 { XFER_MW_DMA_1, 0xa0ca8532 },
101 { XFER_MW_DMA_0, 0xa0ca8575 },
102
103 { XFER_PIO_4, 0xc0ca8521 },
104 { XFER_PIO_3, 0xc0ca8532 },
105 { XFER_PIO_2, 0xc0ca8542 },
106 { XFER_PIO_1, 0xc0d08572 },
107 { XFER_PIO_0, 0xc0d08585 },
108 { 0, 0x01208585 }
109};
110
111/**
112 * hpt36x_find_mode - find the hpt36x timing
113 * @ap: ATA port
114 * @speed: transfer mode
115 *
116 * Return the 32bit register programming information for this channel
117 * that matches the speed provided.
118 */
119
120static u32 hpt36x_find_mode(struct ata_port *ap, int speed)
121{
122 struct hpt_clock *clocks = ap->host->private_data;
123
124 while (clocks->xfer_mode) {
125 if (clocks->xfer_mode == speed)
126 return clocks->timing;
127 clocks++;
128 }
129 BUG();
130 return 0xffffffffU; /* silence compiler warning */
131}
132
133static const char * const bad_ata33[] = {
134 "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3",
135 "Maxtor 90845U3", "Maxtor 90650U2",
136 "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5",
137 "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
138 "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6",
139 "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
140 "Maxtor 90510D4",
141 "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
142 "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7",
143 "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
144 "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5",
145 "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
146 NULL
147};
148
149static const char * const bad_ata66_4[] = {
150 "IBM-DTLA-307075",
151 "IBM-DTLA-307060",
152 "IBM-DTLA-307045",
153 "IBM-DTLA-307030",
154 "IBM-DTLA-307020",
155 "IBM-DTLA-307015",
156 "IBM-DTLA-305040",
157 "IBM-DTLA-305030",
158 "IBM-DTLA-305020",
159 "IC35L010AVER07-0",
160 "IC35L020AVER07-0",
161 "IC35L030AVER07-0",
162 "IC35L040AVER07-0",
163 "IC35L060AVER07-0",
164 "WDC AC310200R",
165 NULL
166};
167
168static const char * const bad_ata66_3[] = {
169 "WDC AC310200R",
170 NULL
171};
172
173static int hpt_dma_broken(const struct ata_device *dev, char *modestr,
174 const char * const list[])
175{
176 unsigned char model_num[ATA_ID_PROD_LEN + 1];
177 int i;
178
179 ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));
180
181 i = match_string(list, -1, model_num);
182 if (i >= 0) {
183 ata_dev_warn(dev, "%s is not supported for %s\n", modestr, list[i]);
184 return 1;
185 }
186 return 0;
187}
188
189/**
190 * hpt366_filter - mode selection filter
191 * @adev: ATA device
192 * @mask: Current mask to manipulate and pass back
193 *
194 * Block UDMA on devices that cause trouble with this controller.
195 */
196
197static unsigned int hpt366_filter(struct ata_device *adev, unsigned int mask)
198{
199 if (adev->class == ATA_DEV_ATA) {
200 if (hpt_dma_broken(adev, "UDMA", bad_ata33))
201 mask &= ~ATA_MASK_UDMA;
202 if (hpt_dma_broken(adev, "UDMA3", bad_ata66_3))
203 mask &= ~(0xF8 << ATA_SHIFT_UDMA);
204 if (hpt_dma_broken(adev, "UDMA4", bad_ata66_4))
205 mask &= ~(0xF0 << ATA_SHIFT_UDMA);
206 } else if (adev->class == ATA_DEV_ATAPI)
207 mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
208
209 return mask;
210}
211
212static int hpt36x_cable_detect(struct ata_port *ap)
213{
214 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
215 u8 ata66;
216
217 /*
218 * Each channel of pata_hpt366 occupies separate PCI function
219 * as the primary channel and bit1 indicates the cable type.
220 */
221 pci_read_config_byte(pdev, 0x5A, &ata66);
222 if (ata66 & 2)
223 return ATA_CBL_PATA40;
224 return ATA_CBL_PATA80;
225}
226
227static void hpt366_set_mode(struct ata_port *ap, struct ata_device *adev,
228 u8 mode)
229{
230 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
231 u32 addr = 0x40 + 4 * adev->devno;
232 u32 mask, reg, t;
233
234 /* determine timing mask and find matching clock entry */
235 if (mode < XFER_MW_DMA_0)
236 mask = 0xc1f8ffff;
237 else if (mode < XFER_UDMA_0)
238 mask = 0x303800ff;
239 else
240 mask = 0x30070000;
241
242 t = hpt36x_find_mode(ap, mode);
243
244 /*
245 * Combine new mode bits with old config bits and disable
246 * on-chip PIO FIFO/buffer (and PIO MST mode as well) to avoid
247 * problems handling I/O errors later.
248 */
249 pci_read_config_dword(pdev, addr, ®);
250 reg = ((reg & ~mask) | (t & mask)) & ~0xc0000000;
251 pci_write_config_dword(pdev, addr, reg);
252}
253
254/**
255 * hpt366_set_piomode - PIO setup
256 * @ap: ATA interface
257 * @adev: device on the interface
258 *
259 * Perform PIO mode setup.
260 */
261
262static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
263{
264 hpt366_set_mode(ap, adev, adev->pio_mode);
265}
266
267/**
268 * hpt366_set_dmamode - DMA timing setup
269 * @ap: ATA interface
270 * @adev: Device being configured
271 *
272 * Set up the channel for MWDMA or UDMA modes. Much the same as with
273 * PIO, load the mode number and then set MWDMA or UDMA flag.
274 */
275
276static void hpt366_set_dmamode(struct ata_port *ap, struct ata_device *adev)
277{
278 hpt366_set_mode(ap, adev, adev->dma_mode);
279}
280
281/**
282 * hpt366_prereset - reset the hpt36x bus
283 * @link: ATA link to reset
284 * @deadline: deadline jiffies for the operation
285 *
286 * Perform the initial reset handling for the 36x series controllers.
287 * Reset the hardware and state machine,
288 */
289
290static int hpt366_prereset(struct ata_link *link, unsigned long deadline)
291{
292 struct ata_port *ap = link->ap;
293 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
294 /*
295 * HPT36x chips have one channel per function and have
296 * both channel enable bits located differently and visible
297 * to both functions -- really stupid design decision... :-(
298 * Bit 4 is for the primary channel, bit 5 for the secondary.
299 */
300 static const struct pci_bits hpt366_enable_bits = {
301 0x50, 1, 0x30, 0x30
302 };
303 u8 mcr2;
304
305 if (!pci_test_config_bits(pdev, &hpt366_enable_bits))
306 return -ENOENT;
307
308 pci_read_config_byte(pdev, 0x51, &mcr2);
309 if (mcr2 & 0x80)
310 pci_write_config_byte(pdev, 0x51, mcr2 & ~0x80);
311
312 return ata_sff_prereset(link, deadline);
313}
314
315static const struct scsi_host_template hpt36x_sht = {
316 ATA_BMDMA_SHT(DRV_NAME),
317};
318
319/*
320 * Configuration for HPT366/68
321 */
322
323static struct ata_port_operations hpt366_port_ops = {
324 .inherits = &ata_bmdma_port_ops,
325 .prereset = hpt366_prereset,
326 .cable_detect = hpt36x_cable_detect,
327 .mode_filter = hpt366_filter,
328 .set_piomode = hpt366_set_piomode,
329 .set_dmamode = hpt366_set_dmamode,
330};
331
332/**
333 * hpt36x_init_chipset - common chip setup
334 * @dev: PCI device
335 *
336 * Perform the chip setup work that must be done at both init and
337 * resume time
338 */
339
340static void hpt36x_init_chipset(struct pci_dev *dev)
341{
342 u8 mcr1;
343
344 pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
345 pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
346 pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
347 pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
348
349 /*
350 * Now we'll have to force both channels enabled if at least one
351 * of them has been enabled by BIOS...
352 */
353 pci_read_config_byte(dev, 0x50, &mcr1);
354 if (mcr1 & 0x30)
355 pci_write_config_byte(dev, 0x50, mcr1 | 0x30);
356}
357
358/**
359 * hpt36x_init_one - Initialise an HPT366/368
360 * @dev: PCI device
361 * @id: Entry in match table
362 *
363 * Initialise an HPT36x device. There are some interesting complications
364 * here. Firstly the chip may report 366 and be one of several variants.
365 * Secondly all the timings depend on the clock for the chip which we must
366 * detect and look up
367 *
368 * This is the known chip mappings. It may be missing a couple of later
369 * releases.
370 *
371 * Chip version PCI Rev Notes
372 * HPT366 4 (HPT366) 0 UDMA66
373 * HPT366 4 (HPT366) 1 UDMA66
374 * HPT368 4 (HPT366) 2 UDMA66
375 * HPT37x/30x 4 (HPT366) 3+ Other driver
376 *
377 */
378
379static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
380{
381 static const struct ata_port_info info_hpt366 = {
382 .flags = ATA_FLAG_SLAVE_POSS,
383 .pio_mask = ATA_PIO4,
384 .mwdma_mask = ATA_MWDMA2,
385 .udma_mask = ATA_UDMA4,
386 .port_ops = &hpt366_port_ops
387 };
388 const struct ata_port_info *ppi[] = { &info_hpt366, NULL };
389
390 const void *hpriv = NULL;
391 u32 reg1;
392 int rc;
393
394 rc = pcim_enable_device(dev);
395 if (rc)
396 return rc;
397
398 /* May be a later chip in disguise. Check */
399 /* Newer chips are not in the HPT36x driver. Ignore them */
400 if (dev->revision > 2)
401 return -ENODEV;
402
403 hpt36x_init_chipset(dev);
404
405 pci_read_config_dword(dev, 0x40, ®1);
406
407 /* PCI clocking determines the ATA timing values to use */
408 /* info_hpt366 is safe against re-entry so we can scribble on it */
409 switch ((reg1 & 0xf00) >> 8) {
410 case 9:
411 hpriv = &hpt366_40;
412 break;
413 case 5:
414 hpriv = &hpt366_25;
415 break;
416 default:
417 hpriv = &hpt366_33;
418 break;
419 }
420 /* Now kick off ATA set up */
421 return ata_pci_bmdma_init_one(dev, ppi, &hpt36x_sht, (void *)hpriv, 0);
422}
423
424#ifdef CONFIG_PM_SLEEP
425static int hpt36x_reinit_one(struct pci_dev *dev)
426{
427 struct ata_host *host = pci_get_drvdata(dev);
428 int rc;
429
430 rc = ata_pci_device_do_resume(dev);
431 if (rc)
432 return rc;
433 hpt36x_init_chipset(dev);
434 ata_host_resume(host);
435 return 0;
436}
437#endif
438
439static const struct pci_device_id hpt36x[] = {
440 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
441 { },
442};
443
444static struct pci_driver hpt36x_pci_driver = {
445 .name = DRV_NAME,
446 .id_table = hpt36x,
447 .probe = hpt36x_init_one,
448 .remove = ata_pci_remove_one,
449#ifdef CONFIG_PM_SLEEP
450 .suspend = ata_pci_device_suspend,
451 .resume = hpt36x_reinit_one,
452#endif
453};
454
455module_pci_driver(hpt36x_pci_driver);
456
457MODULE_AUTHOR("Alan Cox");
458MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368");
459MODULE_LICENSE("GPL");
460MODULE_DEVICE_TABLE(pci, hpt36x);
461MODULE_VERSION(DRV_VERSION);
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Libata driver for the highpoint 366 and 368 UDMA66 ATA controllers.
4 *
5 * This driver is heavily based upon:
6 *
7 * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003
8 *
9 * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
10 * Portions Copyright (C) 2001 Sun Microsystems, Inc.
11 * Portions Copyright (C) 2003 Red Hat Inc
12 *
13 *
14 * TODO
15 * Look into engine reset on timeout errors. Should not be required.
16 */
17
18#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
19
20#include <linux/kernel.h>
21#include <linux/module.h>
22#include <linux/pci.h>
23#include <linux/blkdev.h>
24#include <linux/delay.h>
25#include <scsi/scsi_host.h>
26#include <linux/libata.h>
27
28#define DRV_NAME "pata_hpt366"
29#define DRV_VERSION "0.6.11"
30
31struct hpt_clock {
32 u8 xfer_mode;
33 u32 timing;
34};
35
36/* key for bus clock timings
37 * bit
38 * 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
39 * cycles = value + 1
40 * 4:7 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
41 * cycles = value + 1
42 * 8:11 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
43 * register access.
44 * 12:15 cmd_low_time. Active time of DIOW_/DIOR_ during task file
45 * register access.
46 * 16:18 udma_cycle_time. Clock cycles for UDMA xfer?
47 * 19:21 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
48 * 22:24 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
49 * register access.
50 * 28 UDMA enable.
51 * 29 DMA enable.
52 * 30 PIO_MST enable. If set, the chip is in bus master mode during
53 * PIO xfer.
54 * 31 FIFO enable.
55 */
56
57static const struct hpt_clock hpt366_40[] = {
58 { XFER_UDMA_4, 0x900fd943 },
59 { XFER_UDMA_3, 0x900ad943 },
60 { XFER_UDMA_2, 0x900bd943 },
61 { XFER_UDMA_1, 0x9008d943 },
62 { XFER_UDMA_0, 0x9008d943 },
63
64 { XFER_MW_DMA_2, 0xa008d943 },
65 { XFER_MW_DMA_1, 0xa010d955 },
66 { XFER_MW_DMA_0, 0xa010d9fc },
67
68 { XFER_PIO_4, 0xc008d963 },
69 { XFER_PIO_3, 0xc010d974 },
70 { XFER_PIO_2, 0xc010d997 },
71 { XFER_PIO_1, 0xc010d9c7 },
72 { XFER_PIO_0, 0xc018d9d9 },
73 { 0, 0x0120d9d9 }
74};
75
76static const struct hpt_clock hpt366_33[] = {
77 { XFER_UDMA_4, 0x90c9a731 },
78 { XFER_UDMA_3, 0x90cfa731 },
79 { XFER_UDMA_2, 0x90caa731 },
80 { XFER_UDMA_1, 0x90cba731 },
81 { XFER_UDMA_0, 0x90c8a731 },
82
83 { XFER_MW_DMA_2, 0xa0c8a731 },
84 { XFER_MW_DMA_1, 0xa0c8a732 }, /* 0xa0c8a733 */
85 { XFER_MW_DMA_0, 0xa0c8a797 },
86
87 { XFER_PIO_4, 0xc0c8a731 },
88 { XFER_PIO_3, 0xc0c8a742 },
89 { XFER_PIO_2, 0xc0d0a753 },
90 { XFER_PIO_1, 0xc0d0a7a3 }, /* 0xc0d0a793 */
91 { XFER_PIO_0, 0xc0d0a7aa }, /* 0xc0d0a7a7 */
92 { 0, 0x0120a7a7 }
93};
94
95static const struct hpt_clock hpt366_25[] = {
96 { XFER_UDMA_4, 0x90c98521 },
97 { XFER_UDMA_3, 0x90cf8521 },
98 { XFER_UDMA_2, 0x90cf8521 },
99 { XFER_UDMA_1, 0x90cb8521 },
100 { XFER_UDMA_0, 0x90cb8521 },
101
102 { XFER_MW_DMA_2, 0xa0ca8521 },
103 { XFER_MW_DMA_1, 0xa0ca8532 },
104 { XFER_MW_DMA_0, 0xa0ca8575 },
105
106 { XFER_PIO_4, 0xc0ca8521 },
107 { XFER_PIO_3, 0xc0ca8532 },
108 { XFER_PIO_2, 0xc0ca8542 },
109 { XFER_PIO_1, 0xc0d08572 },
110 { XFER_PIO_0, 0xc0d08585 },
111 { 0, 0x01208585 }
112};
113
114/**
115 * hpt36x_find_mode - find the hpt36x timing
116 * @ap: ATA port
117 * @speed: transfer mode
118 *
119 * Return the 32bit register programming information for this channel
120 * that matches the speed provided.
121 */
122
123static u32 hpt36x_find_mode(struct ata_port *ap, int speed)
124{
125 struct hpt_clock *clocks = ap->host->private_data;
126
127 while (clocks->xfer_mode) {
128 if (clocks->xfer_mode == speed)
129 return clocks->timing;
130 clocks++;
131 }
132 BUG();
133 return 0xffffffffU; /* silence compiler warning */
134}
135
136static const char * const bad_ata33[] = {
137 "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3",
138 "Maxtor 90845U3", "Maxtor 90650U2",
139 "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5",
140 "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
141 "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6",
142 "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
143 "Maxtor 90510D4",
144 "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
145 "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7",
146 "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
147 "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5",
148 "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
149 NULL
150};
151
152static const char * const bad_ata66_4[] = {
153 "IBM-DTLA-307075",
154 "IBM-DTLA-307060",
155 "IBM-DTLA-307045",
156 "IBM-DTLA-307030",
157 "IBM-DTLA-307020",
158 "IBM-DTLA-307015",
159 "IBM-DTLA-305040",
160 "IBM-DTLA-305030",
161 "IBM-DTLA-305020",
162 "IC35L010AVER07-0",
163 "IC35L020AVER07-0",
164 "IC35L030AVER07-0",
165 "IC35L040AVER07-0",
166 "IC35L060AVER07-0",
167 "WDC AC310200R",
168 NULL
169};
170
171static const char * const bad_ata66_3[] = {
172 "WDC AC310200R",
173 NULL
174};
175
176static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr,
177 const char * const list[])
178{
179 unsigned char model_num[ATA_ID_PROD_LEN + 1];
180 int i;
181
182 ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));
183
184 i = match_string(list, -1, model_num);
185 if (i >= 0) {
186 pr_warn("%s is not supported for %s\n", modestr, list[i]);
187 return 1;
188 }
189 return 0;
190}
191
192/**
193 * hpt366_filter - mode selection filter
194 * @adev: ATA device
195 *
196 * Block UDMA on devices that cause trouble with this controller.
197 */
198
199static unsigned long hpt366_filter(struct ata_device *adev, unsigned long mask)
200{
201 if (adev->class == ATA_DEV_ATA) {
202 if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33))
203 mask &= ~ATA_MASK_UDMA;
204 if (hpt_dma_blacklisted(adev, "UDMA3", bad_ata66_3))
205 mask &= ~(0xF8 << ATA_SHIFT_UDMA);
206 if (hpt_dma_blacklisted(adev, "UDMA4", bad_ata66_4))
207 mask &= ~(0xF0 << ATA_SHIFT_UDMA);
208 } else if (adev->class == ATA_DEV_ATAPI)
209 mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
210
211 return mask;
212}
213
214static int hpt36x_cable_detect(struct ata_port *ap)
215{
216 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
217 u8 ata66;
218
219 /*
220 * Each channel of pata_hpt366 occupies separate PCI function
221 * as the primary channel and bit1 indicates the cable type.
222 */
223 pci_read_config_byte(pdev, 0x5A, &ata66);
224 if (ata66 & 2)
225 return ATA_CBL_PATA40;
226 return ATA_CBL_PATA80;
227}
228
229static void hpt366_set_mode(struct ata_port *ap, struct ata_device *adev,
230 u8 mode)
231{
232 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
233 u32 addr = 0x40 + 4 * adev->devno;
234 u32 mask, reg, t;
235
236 /* determine timing mask and find matching clock entry */
237 if (mode < XFER_MW_DMA_0)
238 mask = 0xc1f8ffff;
239 else if (mode < XFER_UDMA_0)
240 mask = 0x303800ff;
241 else
242 mask = 0x30070000;
243
244 t = hpt36x_find_mode(ap, mode);
245
246 /*
247 * Combine new mode bits with old config bits and disable
248 * on-chip PIO FIFO/buffer (and PIO MST mode as well) to avoid
249 * problems handling I/O errors later.
250 */
251 pci_read_config_dword(pdev, addr, ®);
252 reg = ((reg & ~mask) | (t & mask)) & ~0xc0000000;
253 pci_write_config_dword(pdev, addr, reg);
254}
255
256/**
257 * hpt366_set_piomode - PIO setup
258 * @ap: ATA interface
259 * @adev: device on the interface
260 *
261 * Perform PIO mode setup.
262 */
263
264static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
265{
266 hpt366_set_mode(ap, adev, adev->pio_mode);
267}
268
269/**
270 * hpt366_set_dmamode - DMA timing setup
271 * @ap: ATA interface
272 * @adev: Device being configured
273 *
274 * Set up the channel for MWDMA or UDMA modes. Much the same as with
275 * PIO, load the mode number and then set MWDMA or UDMA flag.
276 */
277
278static void hpt366_set_dmamode(struct ata_port *ap, struct ata_device *adev)
279{
280 hpt366_set_mode(ap, adev, adev->dma_mode);
281}
282
283static struct scsi_host_template hpt36x_sht = {
284 ATA_BMDMA_SHT(DRV_NAME),
285};
286
287/*
288 * Configuration for HPT366/68
289 */
290
291static struct ata_port_operations hpt366_port_ops = {
292 .inherits = &ata_bmdma_port_ops,
293 .cable_detect = hpt36x_cable_detect,
294 .mode_filter = hpt366_filter,
295 .set_piomode = hpt366_set_piomode,
296 .set_dmamode = hpt366_set_dmamode,
297};
298
299/**
300 * hpt36x_init_chipset - common chip setup
301 * @dev: PCI device
302 *
303 * Perform the chip setup work that must be done at both init and
304 * resume time
305 */
306
307static void hpt36x_init_chipset(struct pci_dev *dev)
308{
309 u8 drive_fast;
310
311 pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
312 pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
313 pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
314 pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
315
316 pci_read_config_byte(dev, 0x51, &drive_fast);
317 if (drive_fast & 0x80)
318 pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
319}
320
321/**
322 * hpt36x_init_one - Initialise an HPT366/368
323 * @dev: PCI device
324 * @id: Entry in match table
325 *
326 * Initialise an HPT36x device. There are some interesting complications
327 * here. Firstly the chip may report 366 and be one of several variants.
328 * Secondly all the timings depend on the clock for the chip which we must
329 * detect and look up
330 *
331 * This is the known chip mappings. It may be missing a couple of later
332 * releases.
333 *
334 * Chip version PCI Rev Notes
335 * HPT366 4 (HPT366) 0 UDMA66
336 * HPT366 4 (HPT366) 1 UDMA66
337 * HPT368 4 (HPT366) 2 UDMA66
338 * HPT37x/30x 4 (HPT366) 3+ Other driver
339 *
340 */
341
342static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
343{
344 static const struct ata_port_info info_hpt366 = {
345 .flags = ATA_FLAG_SLAVE_POSS,
346 .pio_mask = ATA_PIO4,
347 .mwdma_mask = ATA_MWDMA2,
348 .udma_mask = ATA_UDMA4,
349 .port_ops = &hpt366_port_ops
350 };
351 const struct ata_port_info *ppi[] = { &info_hpt366, NULL };
352
353 const void *hpriv = NULL;
354 u32 reg1;
355 int rc;
356
357 rc = pcim_enable_device(dev);
358 if (rc)
359 return rc;
360
361 /* May be a later chip in disguise. Check */
362 /* Newer chips are not in the HPT36x driver. Ignore them */
363 if (dev->revision > 2)
364 return -ENODEV;
365
366 hpt36x_init_chipset(dev);
367
368 pci_read_config_dword(dev, 0x40, ®1);
369
370 /* PCI clocking determines the ATA timing values to use */
371 /* info_hpt366 is safe against re-entry so we can scribble on it */
372 switch ((reg1 & 0xf00) >> 8) {
373 case 9:
374 hpriv = &hpt366_40;
375 break;
376 case 5:
377 hpriv = &hpt366_25;
378 break;
379 default:
380 hpriv = &hpt366_33;
381 break;
382 }
383 /* Now kick off ATA set up */
384 return ata_pci_bmdma_init_one(dev, ppi, &hpt36x_sht, (void *)hpriv, 0);
385}
386
387#ifdef CONFIG_PM_SLEEP
388static int hpt36x_reinit_one(struct pci_dev *dev)
389{
390 struct ata_host *host = pci_get_drvdata(dev);
391 int rc;
392
393 rc = ata_pci_device_do_resume(dev);
394 if (rc)
395 return rc;
396 hpt36x_init_chipset(dev);
397 ata_host_resume(host);
398 return 0;
399}
400#endif
401
402static const struct pci_device_id hpt36x[] = {
403 { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
404 { },
405};
406
407static struct pci_driver hpt36x_pci_driver = {
408 .name = DRV_NAME,
409 .id_table = hpt36x,
410 .probe = hpt36x_init_one,
411 .remove = ata_pci_remove_one,
412#ifdef CONFIG_PM_SLEEP
413 .suspend = ata_pci_device_suspend,
414 .resume = hpt36x_reinit_one,
415#endif
416};
417
418module_pci_driver(hpt36x_pci_driver);
419
420MODULE_AUTHOR("Alan Cox");
421MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368");
422MODULE_LICENSE("GPL");
423MODULE_DEVICE_TABLE(pci, hpt36x);
424MODULE_VERSION(DRV_VERSION);