Loading...
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# For a description of the syntax of this configuration file,
4# see Documentation/kbuild/kconfig-language.rst.
5#
6
7menu "Firmware Drivers"
8
9source "drivers/firmware/arm_scmi/Kconfig"
10
11config ARM_SCPI_PROTOCOL
12 tristate "ARM System Control and Power Interface (SCPI) Message Protocol"
13 depends on ARM || ARM64 || COMPILE_TEST
14 depends on MAILBOX
15 help
16 System Control and Power Interface (SCPI) Message Protocol is
17 defined for the purpose of communication between the Application
18 Cores(AP) and the System Control Processor(SCP). The MHU peripheral
19 provides a mechanism for inter-processor communication between SCP
20 and AP.
21
22 SCP controls most of the power management on the Application
23 Processors. It offers control and management of: the core/cluster
24 power states, various power domain DVFS including the core/cluster,
25 certain system clocks configuration, thermal sensors and many
26 others.
27
28 This protocol library provides interface for all the client drivers
29 making use of the features offered by the SCP.
30
31config ARM_SDE_INTERFACE
32 bool "ARM Software Delegated Exception Interface (SDEI)"
33 depends on ARM64
34 depends on ACPI_APEI_GHES
35 help
36 The Software Delegated Exception Interface (SDEI) is an ARM
37 standard for registering callbacks from the platform firmware
38 into the OS. This is typically used to implement RAS notifications.
39
40config EDD
41 tristate "BIOS Enhanced Disk Drive calls determine boot disk"
42 depends on X86
43 help
44 Say Y or M here if you want to enable BIOS Enhanced Disk Drive
45 Services real mode BIOS calls to determine which disk
46 BIOS tries boot from. This information is then exported via sysfs.
47
48 This option is experimental and is known to fail to boot on some
49 obscure configurations. Most disk controller BIOS vendors do
50 not yet implement this feature.
51
52config EDD_OFF
53 bool "Sets default behavior for EDD detection to off"
54 depends on EDD
55 default n
56 help
57 Say Y if you want EDD disabled by default, even though it is compiled into the
58 kernel. Say N if you want EDD enabled by default. EDD can be dynamically set
59 using the kernel parameter 'edd={on|skipmbr|off}'.
60
61config FIRMWARE_MEMMAP
62 bool "Add firmware-provided memory map to sysfs" if EXPERT
63 default X86
64 help
65 Add the firmware-provided (unmodified) memory map to /sys/firmware/memmap.
66 That memory map is used for example by kexec to set up parameter area
67 for the next kernel, but can also be used for debugging purposes.
68
69 See also Documentation/ABI/testing/sysfs-firmware-memmap.
70
71config DMIID
72 bool "Export DMI identification via sysfs to userspace"
73 depends on DMI
74 default y
75 help
76 Say Y here if you want to query SMBIOS/DMI system identification
77 information from userspace through /sys/class/dmi/id/ or if you want
78 DMI-based module auto-loading.
79
80config DMI_SYSFS
81 tristate "DMI table support in sysfs"
82 depends on SYSFS && DMI
83 default n
84 help
85 Say Y or M here to enable the exporting of the raw DMI table
86 data via sysfs. This is useful for consuming the data without
87 requiring any access to /dev/mem at all. Tables are found
88 under /sys/firmware/dmi when this option is enabled and
89 loaded.
90
91config DMI_SCAN_MACHINE_NON_EFI_FALLBACK
92 bool
93
94config ISCSI_IBFT_FIND
95 bool "iSCSI Boot Firmware Table Attributes"
96 depends on X86 && ISCSI_IBFT
97 default n
98 help
99 This option enables the kernel to find the region of memory
100 in which the ISCSI Boot Firmware Table (iBFT) resides. This
101 is necessary for iSCSI Boot Firmware Table Attributes module to work
102 properly.
103
104config ISCSI_IBFT
105 tristate "iSCSI Boot Firmware Table Attributes module"
106 select ISCSI_BOOT_SYSFS
107 select ISCSI_IBFT_FIND if X86
108 depends on ACPI && SCSI && SCSI_LOWLEVEL
109 default n
110 help
111 This option enables support for detection and exposing of iSCSI
112 Boot Firmware Table (iBFT) via sysfs to userspace. If you wish to
113 detect iSCSI boot parameters dynamically during system boot, say Y.
114 Otherwise, say N.
115
116config RASPBERRYPI_FIRMWARE
117 tristate "Raspberry Pi Firmware Driver"
118 depends on BCM2835_MBOX
119 help
120 This option enables support for communicating with the firmware on the
121 Raspberry Pi.
122
123config FW_CFG_SYSFS
124 tristate "QEMU fw_cfg device support in sysfs"
125 depends on SYSFS && (ARM || ARM64 || PARISC || PPC_PMAC || RISCV || SPARC || X86)
126 depends on HAS_IOPORT_MAP
127 default n
128 help
129 Say Y or M here to enable the exporting of the QEMU firmware
130 configuration (fw_cfg) file entries via sysfs. Entries are
131 found under /sys/firmware/fw_cfg when this option is enabled
132 and loaded.
133
134config FW_CFG_SYSFS_CMDLINE
135 bool "QEMU fw_cfg device parameter parsing"
136 depends on FW_CFG_SYSFS
137 help
138 Allow the qemu_fw_cfg device to be initialized via the kernel
139 command line or using a module parameter.
140 WARNING: Using incorrect parameters (base address in particular)
141 may crash your system.
142
143config INTEL_STRATIX10_SERVICE
144 tristate "Intel Stratix10 Service Layer"
145 depends on ARCH_INTEL_SOCFPGA && ARM64 && HAVE_ARM_SMCCC
146 default n
147 help
148 Intel Stratix10 service layer runs at privileged exception level,
149 interfaces with the service providers (FPGA manager is one of them)
150 and manages secure monitor call to communicate with secure monitor
151 software at secure monitor exception level.
152
153 Say Y here if you want Stratix10 service layer support.
154
155config INTEL_STRATIX10_RSU
156 tristate "Intel Stratix10 Remote System Update"
157 depends on INTEL_STRATIX10_SERVICE
158 help
159 The Intel Remote System Update (RSU) driver exposes interfaces
160 access through the Intel Service Layer to user space via sysfs
161 device attribute nodes. The RSU interfaces report/control some of
162 the optional RSU features of the Stratix 10 SoC FPGA.
163
164 The RSU provides a way for customers to update the boot
165 configuration of a Stratix 10 SoC device with significantly reduced
166 risk of corrupting the bitstream storage and bricking the system.
167
168 Enable RSU support if you are using an Intel SoC FPGA with the RSU
169 feature enabled and you want Linux user space control.
170
171 Say Y here if you want Intel RSU support.
172
173config MTK_ADSP_IPC
174 tristate "MTK ADSP IPC Protocol driver"
175 depends on MTK_ADSP_MBOX
176 help
177 Say yes here to add support for the MediaTek ADSP IPC
178 between host AP (Linux) and the firmware running on ADSP.
179 ADSP exists on some mtk processors.
180 Client might use shared memory to exchange information with ADSP.
181
182config SYSFB
183 bool
184 select BOOT_VESA_SUPPORT
185 select SCREEN_INFO
186
187config SYSFB_SIMPLEFB
188 bool "Mark VGA/VBE/EFI FB as generic system framebuffer"
189 depends on X86 || EFI
190 select SYSFB
191 help
192 Firmwares often provide initial graphics framebuffers so the BIOS,
193 bootloader or kernel can show basic video-output during boot for
194 user-guidance and debugging. Historically, x86 used the VESA BIOS
195 Extensions and EFI-framebuffers for this, which are mostly limited
196 to x86 BIOS or EFI systems.
197 This option, if enabled, marks VGA/VBE/EFI framebuffers as generic
198 framebuffers so the new generic system-framebuffer drivers can be
199 used instead. If the framebuffer is not compatible with the generic
200 modes, it is advertised as fallback platform framebuffer so legacy
201 drivers like efifb, vesafb and uvesafb can pick it up.
202 If this option is not selected, all system framebuffers are always
203 marked as fallback platform framebuffers as usual.
204
205 Note: Legacy fbdev drivers, including vesafb, efifb, uvesafb, will
206 not be able to pick up generic system framebuffers if this option
207 is selected. You are highly encouraged to enable simplefb as
208 replacement if you select this option. simplefb can correctly deal
209 with generic system framebuffers. But you should still keep vesafb
210 and others enabled as fallback if a system framebuffer is
211 incompatible with simplefb.
212
213 If unsure, say Y.
214
215config TI_SCI_PROTOCOL
216 tristate "TI System Control Interface (TISCI) Message Protocol"
217 depends on TI_MESSAGE_MANAGER
218 help
219 TI System Control Interface (TISCI) Message Protocol is used to manage
220 compute systems such as ARM, DSP etc with the system controller in
221 complex System on Chip(SoC) such as those found on certain keystone
222 generation SoC from TI.
223
224 System controller provides various facilities including power
225 management function support.
226
227 This protocol library is used by client drivers to use the features
228 provided by the system controller.
229
230config TRUSTED_FOUNDATIONS
231 bool "Trusted Foundations secure monitor support"
232 depends on ARM && CPU_V7
233 help
234 Some devices (including most early Tegra-based consumer devices on
235 the market) are booted with the Trusted Foundations secure monitor
236 active, requiring some core operations to be performed by the secure
237 monitor instead of the kernel.
238
239 This option allows the kernel to invoke the secure monitor whenever
240 required on devices using Trusted Foundations. See the functions and
241 comments in linux/firmware/trusted_foundations.h or the device tree
242 bindings for "tlm,trusted-foundations" for details on how to use it.
243
244 Choose N if you don't know what this is about.
245
246config TURRIS_MOX_RWTM
247 tristate "Turris Mox rWTM secure firmware driver"
248 depends on ARCH_MVEBU || COMPILE_TEST
249 depends on HAS_DMA && OF
250 depends on MAILBOX
251 select HW_RANDOM
252 select ARMADA_37XX_RWTM_MBOX
253 help
254 This driver communicates with the firmware on the Cortex-M3 secure
255 processor of the Turris Mox router. Enable if you are building for
256 Turris Mox, and you will be able to read the device serial number and
257 other manufacturing data and also utilize the Entropy Bit Generator
258 for hardware random number generation.
259
260source "drivers/firmware/arm_ffa/Kconfig"
261source "drivers/firmware/broadcom/Kconfig"
262source "drivers/firmware/cirrus/Kconfig"
263source "drivers/firmware/google/Kconfig"
264source "drivers/firmware/efi/Kconfig"
265source "drivers/firmware/imx/Kconfig"
266source "drivers/firmware/meson/Kconfig"
267source "drivers/firmware/microchip/Kconfig"
268source "drivers/firmware/psci/Kconfig"
269source "drivers/firmware/qcom/Kconfig"
270source "drivers/firmware/smccc/Kconfig"
271source "drivers/firmware/tegra/Kconfig"
272source "drivers/firmware/xilinx/Kconfig"
273
274endmenu
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# For a description of the syntax of this configuration file,
4# see Documentation/kbuild/kconfig-language.rst.
5#
6
7menu "Firmware Drivers"
8
9config ARM_SCMI_PROTOCOL
10 bool "ARM System Control and Management Interface (SCMI) Message Protocol"
11 depends on ARM || ARM64 || COMPILE_TEST
12 depends on MAILBOX
13 help
14 ARM System Control and Management Interface (SCMI) protocol is a
15 set of operating system-independent software interfaces that are
16 used in system management. SCMI is extensible and currently provides
17 interfaces for: Discovery and self-description of the interfaces
18 it supports, Power domain management which is the ability to place
19 a given device or domain into the various power-saving states that
20 it supports, Performance management which is the ability to control
21 the performance of a domain that is composed of compute engines
22 such as application processors and other accelerators, Clock
23 management which is the ability to set and inquire rates on platform
24 managed clocks and Sensor management which is the ability to read
25 sensor data, and be notified of sensor value.
26
27 This protocol library provides interface for all the client drivers
28 making use of the features offered by the SCMI.
29
30config ARM_SCMI_POWER_DOMAIN
31 tristate "SCMI power domain driver"
32 depends on ARM_SCMI_PROTOCOL || (COMPILE_TEST && OF)
33 default y
34 select PM_GENERIC_DOMAINS if PM
35 help
36 This enables support for the SCMI power domains which can be
37 enabled or disabled via the SCP firmware
38
39 This driver can also be built as a module. If so, the module
40 will be called scmi_pm_domain. Note this may needed early in boot
41 before rootfs may be available.
42
43config ARM_SCPI_PROTOCOL
44 tristate "ARM System Control and Power Interface (SCPI) Message Protocol"
45 depends on ARM || ARM64 || COMPILE_TEST
46 depends on MAILBOX
47 help
48 System Control and Power Interface (SCPI) Message Protocol is
49 defined for the purpose of communication between the Application
50 Cores(AP) and the System Control Processor(SCP). The MHU peripheral
51 provides a mechanism for inter-processor communication between SCP
52 and AP.
53
54 SCP controls most of the power managament on the Application
55 Processors. It offers control and management of: the core/cluster
56 power states, various power domain DVFS including the core/cluster,
57 certain system clocks configuration, thermal sensors and many
58 others.
59
60 This protocol library provides interface for all the client drivers
61 making use of the features offered by the SCP.
62
63config ARM_SCPI_POWER_DOMAIN
64 tristate "SCPI power domain driver"
65 depends on ARM_SCPI_PROTOCOL || (COMPILE_TEST && OF)
66 default y
67 select PM_GENERIC_DOMAINS if PM
68 help
69 This enables support for the SCPI power domains which can be
70 enabled or disabled via the SCP firmware
71
72config ARM_SDE_INTERFACE
73 bool "ARM Software Delegated Exception Interface (SDEI)"
74 depends on ARM64
75 help
76 The Software Delegated Exception Interface (SDEI) is an ARM
77 standard for registering callbacks from the platform firmware
78 into the OS. This is typically used to implement RAS notifications.
79
80config EDD
81 tristate "BIOS Enhanced Disk Drive calls determine boot disk"
82 depends on X86
83 help
84 Say Y or M here if you want to enable BIOS Enhanced Disk Drive
85 Services real mode BIOS calls to determine which disk
86 BIOS tries boot from. This information is then exported via sysfs.
87
88 This option is experimental and is known to fail to boot on some
89 obscure configurations. Most disk controller BIOS vendors do
90 not yet implement this feature.
91
92config EDD_OFF
93 bool "Sets default behavior for EDD detection to off"
94 depends on EDD
95 default n
96 help
97 Say Y if you want EDD disabled by default, even though it is compiled into the
98 kernel. Say N if you want EDD enabled by default. EDD can be dynamically set
99 using the kernel parameter 'edd={on|skipmbr|off}'.
100
101config FIRMWARE_MEMMAP
102 bool "Add firmware-provided memory map to sysfs" if EXPERT
103 default X86
104 help
105 Add the firmware-provided (unmodified) memory map to /sys/firmware/memmap.
106 That memory map is used for example by kexec to set up parameter area
107 for the next kernel, but can also be used for debugging purposes.
108
109 See also Documentation/ABI/testing/sysfs-firmware-memmap.
110
111config EFI_PCDP
112 bool "Console device selection via EFI PCDP or HCDP table"
113 depends on ACPI && EFI && IA64
114 default y if IA64
115 help
116 If your firmware supplies the PCDP table, and you want to
117 automatically use the primary console device it describes
118 as the Linux console, say Y here.
119
120 If your firmware supplies the HCDP table, and you want to
121 use the first serial port it describes as the Linux console,
122 say Y here. If your EFI ConOut path contains only a UART
123 device, it will become the console automatically. Otherwise,
124 you must specify the "console=hcdp" kernel boot argument.
125
126 Neither the PCDP nor the HCDP affects naming of serial devices,
127 so a serial console may be /dev/ttyS0, /dev/ttyS1, etc, depending
128 on how the driver discovers devices.
129
130 You must also enable the appropriate drivers (serial, VGA, etc.)
131
132 See DIG64_HCDPv20_042804.pdf available from
133 <http://www.dig64.org/specifications/>
134
135config DMIID
136 bool "Export DMI identification via sysfs to userspace"
137 depends on DMI
138 default y
139 help
140 Say Y here if you want to query SMBIOS/DMI system identification
141 information from userspace through /sys/class/dmi/id/ or if you want
142 DMI-based module auto-loading.
143
144config DMI_SYSFS
145 tristate "DMI table support in sysfs"
146 depends on SYSFS && DMI
147 default n
148 help
149 Say Y or M here to enable the exporting of the raw DMI table
150 data via sysfs. This is useful for consuming the data without
151 requiring any access to /dev/mem at all. Tables are found
152 under /sys/firmware/dmi when this option is enabled and
153 loaded.
154
155config DMI_SCAN_MACHINE_NON_EFI_FALLBACK
156 bool
157
158config ISCSI_IBFT_FIND
159 bool "iSCSI Boot Firmware Table Attributes"
160 depends on X86 && ISCSI_IBFT
161 default n
162 help
163 This option enables the kernel to find the region of memory
164 in which the ISCSI Boot Firmware Table (iBFT) resides. This
165 is necessary for iSCSI Boot Firmware Table Attributes module to work
166 properly.
167
168config ISCSI_IBFT
169 tristate "iSCSI Boot Firmware Table Attributes module"
170 select ISCSI_BOOT_SYSFS
171 select ISCSI_IBFT_FIND if X86
172 depends on ACPI && SCSI && SCSI_LOWLEVEL
173 default n
174 help
175 This option enables support for detection and exposing of iSCSI
176 Boot Firmware Table (iBFT) via sysfs to userspace. If you wish to
177 detect iSCSI boot parameters dynamically during system boot, say Y.
178 Otherwise, say N.
179
180config RASPBERRYPI_FIRMWARE
181 tristate "Raspberry Pi Firmware Driver"
182 depends on BCM2835_MBOX
183 help
184 This option enables support for communicating with the firmware on the
185 Raspberry Pi.
186
187config FW_CFG_SYSFS
188 tristate "QEMU fw_cfg device support in sysfs"
189 depends on SYSFS && (ARM || ARM64 || PPC_PMAC || SPARC || X86)
190 depends on HAS_IOPORT_MAP
191 default n
192 help
193 Say Y or M here to enable the exporting of the QEMU firmware
194 configuration (fw_cfg) file entries via sysfs. Entries are
195 found under /sys/firmware/fw_cfg when this option is enabled
196 and loaded.
197
198config FW_CFG_SYSFS_CMDLINE
199 bool "QEMU fw_cfg device parameter parsing"
200 depends on FW_CFG_SYSFS
201 help
202 Allow the qemu_fw_cfg device to be initialized via the kernel
203 command line or using a module parameter.
204 WARNING: Using incorrect parameters (base address in particular)
205 may crash your system.
206
207config INTEL_STRATIX10_SERVICE
208 tristate "Intel Stratix10 Service Layer"
209 depends on ARCH_STRATIX10 && HAVE_ARM_SMCCC
210 default n
211 help
212 Intel Stratix10 service layer runs at privileged exception level,
213 interfaces with the service providers (FPGA manager is one of them)
214 and manages secure monitor call to communicate with secure monitor
215 software at secure monitor exception level.
216
217 Say Y here if you want Stratix10 service layer support.
218
219config INTEL_STRATIX10_RSU
220 tristate "Intel Stratix10 Remote System Update"
221 depends on INTEL_STRATIX10_SERVICE
222 help
223 The Intel Remote System Update (RSU) driver exposes interfaces
224 access through the Intel Service Layer to user space via sysfs
225 device attribute nodes. The RSU interfaces report/control some of
226 the optional RSU features of the Stratix 10 SoC FPGA.
227
228 The RSU provides a way for customers to update the boot
229 configuration of a Stratix 10 SoC device with significantly reduced
230 risk of corrupting the bitstream storage and bricking the system.
231
232 Enable RSU support if you are using an Intel SoC FPGA with the RSU
233 feature enabled and you want Linux user space control.
234
235 Say Y here if you want Intel RSU support.
236
237config QCOM_SCM
238 bool
239 depends on ARM || ARM64
240 select RESET_CONTROLLER
241
242config QCOM_SCM_32
243 def_bool y
244 depends on QCOM_SCM && ARM
245
246config QCOM_SCM_64
247 def_bool y
248 depends on QCOM_SCM && ARM64
249
250config QCOM_SCM_DOWNLOAD_MODE_DEFAULT
251 bool "Qualcomm download mode enabled by default"
252 depends on QCOM_SCM
253 help
254 A device with "download mode" enabled will upon an unexpected
255 warm-restart enter a special debug mode that allows the user to
256 "download" memory content over USB for offline postmortem analysis.
257 The feature can be enabled/disabled on the kernel command line.
258
259 Say Y here to enable "download mode" by default.
260
261config TI_SCI_PROTOCOL
262 tristate "TI System Control Interface (TISCI) Message Protocol"
263 depends on TI_MESSAGE_MANAGER
264 help
265 TI System Control Interface (TISCI) Message Protocol is used to manage
266 compute systems such as ARM, DSP etc with the system controller in
267 complex System on Chip(SoC) such as those found on certain keystone
268 generation SoC from TI.
269
270 System controller provides various facilities including power
271 management function support.
272
273 This protocol library is used by client drivers to use the features
274 provided by the system controller.
275
276config TRUSTED_FOUNDATIONS
277 bool "Trusted Foundations secure monitor support"
278 depends on ARM && CPU_V7
279 help
280 Some devices (including most early Tegra-based consumer devices on
281 the market) are booted with the Trusted Foundations secure monitor
282 active, requiring some core operations to be performed by the secure
283 monitor instead of the kernel.
284
285 This option allows the kernel to invoke the secure monitor whenever
286 required on devices using Trusted Foundations. See the functions and
287 comments in linux/firmware/trusted_foundations.h or the device tree
288 bindings for "tlm,trusted-foundations" for details on how to use it.
289
290 Choose N if you don't know what this is about.
291
292config TURRIS_MOX_RWTM
293 tristate "Turris Mox rWTM secure firmware driver"
294 depends on ARCH_MVEBU || COMPILE_TEST
295 depends on HAS_DMA && OF
296 depends on MAILBOX
297 select HW_RANDOM
298 select ARMADA_37XX_RWTM_MBOX
299 help
300 This driver communicates with the firmware on the Cortex-M3 secure
301 processor of the Turris Mox router. Enable if you are building for
302 Turris Mox, and you will be able to read the device serial number and
303 other manufacturing data and also utilize the Entropy Bit Generator
304 for hardware random number generation.
305
306config HAVE_ARM_SMCCC
307 bool
308
309source "drivers/firmware/psci/Kconfig"
310source "drivers/firmware/broadcom/Kconfig"
311source "drivers/firmware/google/Kconfig"
312source "drivers/firmware/efi/Kconfig"
313source "drivers/firmware/imx/Kconfig"
314source "drivers/firmware/meson/Kconfig"
315source "drivers/firmware/tegra/Kconfig"
316source "drivers/firmware/xilinx/Kconfig"
317
318endmenu