Loading...
1// SPDX-License-Identifier: GPL-2.0
2/* Copyright (c) 2018 Intel Corporation */
3
4#include <linux/bitfield.h>
5#include "igc_phy.h"
6
7/**
8 * igc_check_reset_block - Check if PHY reset is blocked
9 * @hw: pointer to the HW structure
10 *
11 * Read the PHY management control register and check whether a PHY reset
12 * is blocked. If a reset is not blocked return 0, otherwise
13 * return IGC_ERR_BLK_PHY_RESET (12).
14 */
15s32 igc_check_reset_block(struct igc_hw *hw)
16{
17 u32 manc;
18
19 manc = rd32(IGC_MANC);
20
21 return (manc & IGC_MANC_BLK_PHY_RST_ON_IDE) ?
22 IGC_ERR_BLK_PHY_RESET : 0;
23}
24
25/**
26 * igc_get_phy_id - Retrieve the PHY ID and revision
27 * @hw: pointer to the HW structure
28 *
29 * Reads the PHY registers and stores the PHY ID and possibly the PHY
30 * revision in the hardware structure.
31 */
32s32 igc_get_phy_id(struct igc_hw *hw)
33{
34 struct igc_phy_info *phy = &hw->phy;
35 s32 ret_val = 0;
36 u16 phy_id;
37
38 ret_val = phy->ops.read_reg(hw, PHY_ID1, &phy_id);
39 if (ret_val)
40 goto out;
41
42 phy->id = (u32)(phy_id << 16);
43 usleep_range(200, 500);
44 ret_val = phy->ops.read_reg(hw, PHY_ID2, &phy_id);
45 if (ret_val)
46 goto out;
47
48 phy->id |= (u32)(phy_id & PHY_REVISION_MASK);
49 phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
50
51out:
52 return ret_val;
53}
54
55/**
56 * igc_phy_has_link - Polls PHY for link
57 * @hw: pointer to the HW structure
58 * @iterations: number of times to poll for link
59 * @usec_interval: delay between polling attempts
60 * @success: pointer to whether polling was successful or not
61 *
62 * Polls the PHY status register for link, 'iterations' number of times.
63 */
64s32 igc_phy_has_link(struct igc_hw *hw, u32 iterations,
65 u32 usec_interval, bool *success)
66{
67 u16 i, phy_status;
68 s32 ret_val = 0;
69
70 for (i = 0; i < iterations; i++) {
71 /* Some PHYs require the PHY_STATUS register to be read
72 * twice due to the link bit being sticky. No harm doing
73 * it across the board.
74 */
75 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
76 if (ret_val && usec_interval > 0) {
77 /* If the first read fails, another entity may have
78 * ownership of the resources, wait and try again to
79 * see if they have relinquished the resources yet.
80 */
81 if (usec_interval >= 1000)
82 mdelay(usec_interval / 1000);
83 else
84 udelay(usec_interval);
85 }
86 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
87 if (ret_val)
88 break;
89 if (phy_status & MII_SR_LINK_STATUS)
90 break;
91 if (usec_interval >= 1000)
92 mdelay(usec_interval / 1000);
93 else
94 udelay(usec_interval);
95 }
96
97 *success = (i < iterations) ? true : false;
98
99 return ret_val;
100}
101
102/**
103 * igc_power_up_phy_copper - Restore copper link in case of PHY power down
104 * @hw: pointer to the HW structure
105 *
106 * In the case of a PHY power down to save power, or to turn off link during a
107 * driver unload, restore the link to previous settings.
108 */
109void igc_power_up_phy_copper(struct igc_hw *hw)
110{
111 u16 mii_reg = 0;
112
113 /* The PHY will retain its settings across a power down/up cycle */
114 hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg);
115 mii_reg &= ~MII_CR_POWER_DOWN;
116 hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg);
117}
118
119/**
120 * igc_power_down_phy_copper - Power down copper PHY
121 * @hw: pointer to the HW structure
122 *
123 * Power down PHY to save power when interface is down and wake on lan
124 * is not enabled.
125 */
126void igc_power_down_phy_copper(struct igc_hw *hw)
127{
128 u16 mii_reg = 0;
129
130 /* The PHY will retain its settings across a power down/up cycle */
131 hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg);
132 mii_reg |= MII_CR_POWER_DOWN;
133 hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg);
134 usleep_range(1000, 2000);
135}
136
137/**
138 * igc_check_downshift - Checks whether a downshift in speed occurred
139 * @hw: pointer to the HW structure
140 *
141 * A downshift is detected by querying the PHY link health.
142 */
143void igc_check_downshift(struct igc_hw *hw)
144{
145 struct igc_phy_info *phy = &hw->phy;
146
147 /* speed downshift not supported */
148 phy->speed_downgraded = false;
149}
150
151/**
152 * igc_phy_hw_reset - PHY hardware reset
153 * @hw: pointer to the HW structure
154 *
155 * Verify the reset block is not blocking us from resetting. Acquire
156 * semaphore (if necessary) and read/set/write the device control reset
157 * bit in the PHY. Wait the appropriate delay time for the device to
158 * reset and release the semaphore (if necessary).
159 */
160s32 igc_phy_hw_reset(struct igc_hw *hw)
161{
162 struct igc_phy_info *phy = &hw->phy;
163 u32 phpm = 0, timeout = 10000;
164 s32 ret_val;
165 u32 ctrl;
166
167 ret_val = igc_check_reset_block(hw);
168 if (ret_val) {
169 ret_val = 0;
170 goto out;
171 }
172
173 ret_val = phy->ops.acquire(hw);
174 if (ret_val)
175 goto out;
176
177 phpm = rd32(IGC_I225_PHPM);
178
179 ctrl = rd32(IGC_CTRL);
180 wr32(IGC_CTRL, ctrl | IGC_CTRL_PHY_RST);
181 wrfl();
182
183 udelay(phy->reset_delay_us);
184
185 wr32(IGC_CTRL, ctrl);
186 wrfl();
187
188 /* SW should guarantee 100us for the completion of the PHY reset */
189 usleep_range(100, 150);
190 do {
191 phpm = rd32(IGC_I225_PHPM);
192 timeout--;
193 udelay(1);
194 } while (!(phpm & IGC_PHY_RST_COMP) && timeout);
195
196 if (!timeout)
197 hw_dbg("Timeout is expired after a phy reset\n");
198
199 usleep_range(100, 150);
200
201 phy->ops.release(hw);
202
203out:
204 return ret_val;
205}
206
207/**
208 * igc_phy_setup_autoneg - Configure PHY for auto-negotiation
209 * @hw: pointer to the HW structure
210 *
211 * Reads the MII auto-neg advertisement register and/or the 1000T control
212 * register and if the PHY is already setup for auto-negotiation, then
213 * return successful. Otherwise, setup advertisement and flow control to
214 * the appropriate values for the wanted auto-negotiation.
215 */
216static s32 igc_phy_setup_autoneg(struct igc_hw *hw)
217{
218 struct igc_phy_info *phy = &hw->phy;
219 u16 aneg_multigbt_an_ctrl = 0;
220 u16 mii_1000t_ctrl_reg = 0;
221 u16 mii_autoneg_adv_reg;
222 s32 ret_val;
223
224 phy->autoneg_advertised &= phy->autoneg_mask;
225
226 /* Read the MII Auto-Neg Advertisement Register (Address 4). */
227 ret_val = phy->ops.read_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
228 if (ret_val)
229 return ret_val;
230
231 if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
232 /* Read the MII 1000Base-T Control Register (Address 9). */
233 ret_val = phy->ops.read_reg(hw, PHY_1000T_CTRL,
234 &mii_1000t_ctrl_reg);
235 if (ret_val)
236 return ret_val;
237 }
238
239 if (phy->autoneg_mask & ADVERTISE_2500_FULL) {
240 /* Read the MULTI GBT AN Control Register - reg 7.32 */
241 ret_val = phy->ops.read_reg(hw, (STANDARD_AN_REG_MASK <<
242 MMD_DEVADDR_SHIFT) |
243 IGC_ANEG_MULTIGBT_AN_CTRL,
244 &aneg_multigbt_an_ctrl);
245
246 if (ret_val)
247 return ret_val;
248 }
249
250 /* Need to parse both autoneg_advertised and fc and set up
251 * the appropriate PHY registers. First we will parse for
252 * autoneg_advertised software override. Since we can advertise
253 * a plethora of combinations, we need to check each bit
254 * individually.
255 */
256
257 /* First we clear all the 10/100 mb speed bits in the Auto-Neg
258 * Advertisement Register (Address 4) and the 1000 mb speed bits in
259 * the 1000Base-T Control Register (Address 9).
260 */
261 mii_autoneg_adv_reg &= ~(NWAY_AR_100TX_FD_CAPS |
262 NWAY_AR_100TX_HD_CAPS |
263 NWAY_AR_10T_FD_CAPS |
264 NWAY_AR_10T_HD_CAPS);
265 mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS);
266
267 hw_dbg("autoneg_advertised %x\n", phy->autoneg_advertised);
268
269 /* Do we want to advertise 10 Mb Half Duplex? */
270 if (phy->autoneg_advertised & ADVERTISE_10_HALF) {
271 hw_dbg("Advertise 10mb Half duplex\n");
272 mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
273 }
274
275 /* Do we want to advertise 10 Mb Full Duplex? */
276 if (phy->autoneg_advertised & ADVERTISE_10_FULL) {
277 hw_dbg("Advertise 10mb Full duplex\n");
278 mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
279 }
280
281 /* Do we want to advertise 100 Mb Half Duplex? */
282 if (phy->autoneg_advertised & ADVERTISE_100_HALF) {
283 hw_dbg("Advertise 100mb Half duplex\n");
284 mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
285 }
286
287 /* Do we want to advertise 100 Mb Full Duplex? */
288 if (phy->autoneg_advertised & ADVERTISE_100_FULL) {
289 hw_dbg("Advertise 100mb Full duplex\n");
290 mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
291 }
292
293 /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
294 if (phy->autoneg_advertised & ADVERTISE_1000_HALF)
295 hw_dbg("Advertise 1000mb Half duplex request denied!\n");
296
297 /* Do we want to advertise 1000 Mb Full Duplex? */
298 if (phy->autoneg_advertised & ADVERTISE_1000_FULL) {
299 hw_dbg("Advertise 1000mb Full duplex\n");
300 mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
301 }
302
303 /* We do not allow the Phy to advertise 2500 Mb Half Duplex */
304 if (phy->autoneg_advertised & ADVERTISE_2500_HALF)
305 hw_dbg("Advertise 2500mb Half duplex request denied!\n");
306
307 /* Do we want to advertise 2500 Mb Full Duplex? */
308 if (phy->autoneg_advertised & ADVERTISE_2500_FULL) {
309 hw_dbg("Advertise 2500mb Full duplex\n");
310 aneg_multigbt_an_ctrl |= CR_2500T_FD_CAPS;
311 } else {
312 aneg_multigbt_an_ctrl &= ~CR_2500T_FD_CAPS;
313 }
314
315 /* Check for a software override of the flow control settings, and
316 * setup the PHY advertisement registers accordingly. If
317 * auto-negotiation is enabled, then software will have to set the
318 * "PAUSE" bits to the correct value in the Auto-Negotiation
319 * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-
320 * negotiation.
321 *
322 * The possible values of the "fc" parameter are:
323 * 0: Flow control is completely disabled
324 * 1: Rx flow control is enabled (we can receive pause frames
325 * but not send pause frames).
326 * 2: Tx flow control is enabled (we can send pause frames
327 * but we do not support receiving pause frames).
328 * 3: Both Rx and Tx flow control (symmetric) are enabled.
329 * other: No software override. The flow control configuration
330 * in the EEPROM is used.
331 */
332 switch (hw->fc.current_mode) {
333 case igc_fc_none:
334 /* Flow control (Rx & Tx) is completely disabled by a
335 * software over-ride.
336 */
337 mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
338 break;
339 case igc_fc_rx_pause:
340 /* Rx Flow control is enabled, and Tx Flow control is
341 * disabled, by a software over-ride.
342 *
343 * Since there really isn't a way to advertise that we are
344 * capable of Rx Pause ONLY, we will advertise that we
345 * support both symmetric and asymmetric Rx PAUSE. Later
346 * (in igc_config_fc_after_link_up) we will disable the
347 * hw's ability to send PAUSE frames.
348 */
349 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
350 break;
351 case igc_fc_tx_pause:
352 /* Tx Flow control is enabled, and Rx Flow control is
353 * disabled, by a software over-ride.
354 */
355 mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
356 mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
357 break;
358 case igc_fc_full:
359 /* Flow control (both Rx and Tx) is enabled by a software
360 * over-ride.
361 */
362 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
363 break;
364 default:
365 hw_dbg("Flow control param set incorrectly\n");
366 return -IGC_ERR_CONFIG;
367 }
368
369 ret_val = phy->ops.write_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
370 if (ret_val)
371 return ret_val;
372
373 hw_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
374
375 if (phy->autoneg_mask & ADVERTISE_1000_FULL)
376 ret_val = phy->ops.write_reg(hw, PHY_1000T_CTRL,
377 mii_1000t_ctrl_reg);
378
379 if (phy->autoneg_mask & ADVERTISE_2500_FULL)
380 ret_val = phy->ops.write_reg(hw,
381 (STANDARD_AN_REG_MASK <<
382 MMD_DEVADDR_SHIFT) |
383 IGC_ANEG_MULTIGBT_AN_CTRL,
384 aneg_multigbt_an_ctrl);
385
386 return ret_val;
387}
388
389/**
390 * igc_wait_autoneg - Wait for auto-neg completion
391 * @hw: pointer to the HW structure
392 *
393 * Waits for auto-negotiation to complete or for the auto-negotiation time
394 * limit to expire, which ever happens first.
395 */
396static s32 igc_wait_autoneg(struct igc_hw *hw)
397{
398 u16 i, phy_status;
399 s32 ret_val = 0;
400
401 /* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */
402 for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) {
403 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
404 if (ret_val)
405 break;
406 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
407 if (ret_val)
408 break;
409 if (phy_status & MII_SR_AUTONEG_COMPLETE)
410 break;
411 msleep(100);
412 }
413
414 /* PHY_AUTO_NEG_TIME expiration doesn't guarantee auto-negotiation
415 * has completed.
416 */
417 return ret_val;
418}
419
420/**
421 * igc_copper_link_autoneg - Setup/Enable autoneg for copper link
422 * @hw: pointer to the HW structure
423 *
424 * Performs initial bounds checking on autoneg advertisement parameter, then
425 * configure to advertise the full capability. Setup the PHY to autoneg
426 * and restart the negotiation process between the link partner. If
427 * autoneg_wait_to_complete, then wait for autoneg to complete before exiting.
428 */
429static s32 igc_copper_link_autoneg(struct igc_hw *hw)
430{
431 struct igc_phy_info *phy = &hw->phy;
432 u16 phy_ctrl;
433 s32 ret_val;
434
435 /* Perform some bounds checking on the autoneg advertisement
436 * parameter.
437 */
438 phy->autoneg_advertised &= phy->autoneg_mask;
439
440 /* If autoneg_advertised is zero, we assume it was not defaulted
441 * by the calling code so we set to advertise full capability.
442 */
443 if (phy->autoneg_advertised == 0)
444 phy->autoneg_advertised = phy->autoneg_mask;
445
446 hw_dbg("Reconfiguring auto-neg advertisement params\n");
447 ret_val = igc_phy_setup_autoneg(hw);
448 if (ret_val) {
449 hw_dbg("Error Setting up Auto-Negotiation\n");
450 goto out;
451 }
452 hw_dbg("Restarting Auto-Neg\n");
453
454 /* Restart auto-negotiation by setting the Auto Neg Enable bit and
455 * the Auto Neg Restart bit in the PHY control register.
456 */
457 ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_ctrl);
458 if (ret_val)
459 goto out;
460
461 phy_ctrl |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
462 ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_ctrl);
463 if (ret_val)
464 goto out;
465
466 /* Does the user want to wait for Auto-Neg to complete here, or
467 * check at a later time (for example, callback routine).
468 */
469 if (phy->autoneg_wait_to_complete) {
470 ret_val = igc_wait_autoneg(hw);
471 if (ret_val) {
472 hw_dbg("Error while waiting for autoneg to complete\n");
473 goto out;
474 }
475 }
476
477 hw->mac.get_link_status = true;
478
479out:
480 return ret_val;
481}
482
483/**
484 * igc_setup_copper_link - Configure copper link settings
485 * @hw: pointer to the HW structure
486 *
487 * Calls the appropriate function to configure the link for auto-neg or forced
488 * speed and duplex. Then we check for link, once link is established calls
489 * to configure collision distance and flow control are called. If link is
490 * not established, we return -IGC_ERR_PHY (-2).
491 */
492s32 igc_setup_copper_link(struct igc_hw *hw)
493{
494 s32 ret_val = 0;
495 bool link;
496
497 /* Setup autoneg and flow control advertisement and perform
498 * autonegotiation.
499 */
500 ret_val = igc_copper_link_autoneg(hw);
501 if (ret_val)
502 goto out;
503
504 /* Check link status. Wait up to 100 microseconds for link to become
505 * valid.
506 */
507 ret_val = igc_phy_has_link(hw, COPPER_LINK_UP_LIMIT, 10, &link);
508 if (ret_val)
509 goto out;
510
511 if (link) {
512 hw_dbg("Valid link established!!!\n");
513 igc_config_collision_dist(hw);
514 ret_val = igc_config_fc_after_link_up(hw);
515 } else {
516 hw_dbg("Unable to establish link!!!\n");
517 }
518
519out:
520 return ret_val;
521}
522
523/**
524 * igc_read_phy_reg_mdic - Read MDI control register
525 * @hw: pointer to the HW structure
526 * @offset: register offset to be read
527 * @data: pointer to the read data
528 *
529 * Reads the MDI control register in the PHY at offset and stores the
530 * information read to data.
531 */
532static s32 igc_read_phy_reg_mdic(struct igc_hw *hw, u32 offset, u16 *data)
533{
534 struct igc_phy_info *phy = &hw->phy;
535 u32 i, mdic = 0;
536 s32 ret_val = 0;
537
538 if (offset > MAX_PHY_REG_ADDRESS) {
539 hw_dbg("PHY Address %d is out of range\n", offset);
540 ret_val = -IGC_ERR_PARAM;
541 goto out;
542 }
543
544 /* Set up Op-code, Phy Address, and register offset in the MDI
545 * Control register. The MAC will take care of interfacing with the
546 * PHY to retrieve the desired data.
547 */
548 mdic = ((offset << IGC_MDIC_REG_SHIFT) |
549 (phy->addr << IGC_MDIC_PHY_SHIFT) |
550 (IGC_MDIC_OP_READ));
551
552 wr32(IGC_MDIC, mdic);
553
554 /* Poll the ready bit to see if the MDI read completed
555 * Increasing the time out as testing showed failures with
556 * the lower time out
557 */
558 for (i = 0; i < IGC_GEN_POLL_TIMEOUT; i++) {
559 udelay(50);
560 mdic = rd32(IGC_MDIC);
561 if (mdic & IGC_MDIC_READY)
562 break;
563 }
564 if (!(mdic & IGC_MDIC_READY)) {
565 hw_dbg("MDI Read did not complete\n");
566 ret_val = -IGC_ERR_PHY;
567 goto out;
568 }
569 if (mdic & IGC_MDIC_ERROR) {
570 hw_dbg("MDI Error\n");
571 ret_val = -IGC_ERR_PHY;
572 goto out;
573 }
574 *data = (u16)mdic;
575
576out:
577 return ret_val;
578}
579
580/**
581 * igc_write_phy_reg_mdic - Write MDI control register
582 * @hw: pointer to the HW structure
583 * @offset: register offset to write to
584 * @data: data to write to register at offset
585 *
586 * Writes data to MDI control register in the PHY at offset.
587 */
588static s32 igc_write_phy_reg_mdic(struct igc_hw *hw, u32 offset, u16 data)
589{
590 struct igc_phy_info *phy = &hw->phy;
591 u32 i, mdic = 0;
592 s32 ret_val = 0;
593
594 if (offset > MAX_PHY_REG_ADDRESS) {
595 hw_dbg("PHY Address %d is out of range\n", offset);
596 ret_val = -IGC_ERR_PARAM;
597 goto out;
598 }
599
600 /* Set up Op-code, Phy Address, and register offset in the MDI
601 * Control register. The MAC will take care of interfacing with the
602 * PHY to write the desired data.
603 */
604 mdic = (((u32)data) |
605 (offset << IGC_MDIC_REG_SHIFT) |
606 (phy->addr << IGC_MDIC_PHY_SHIFT) |
607 (IGC_MDIC_OP_WRITE));
608
609 wr32(IGC_MDIC, mdic);
610
611 /* Poll the ready bit to see if the MDI read completed
612 * Increasing the time out as testing showed failures with
613 * the lower time out
614 */
615 for (i = 0; i < IGC_GEN_POLL_TIMEOUT; i++) {
616 udelay(50);
617 mdic = rd32(IGC_MDIC);
618 if (mdic & IGC_MDIC_READY)
619 break;
620 }
621 if (!(mdic & IGC_MDIC_READY)) {
622 hw_dbg("MDI Write did not complete\n");
623 ret_val = -IGC_ERR_PHY;
624 goto out;
625 }
626 if (mdic & IGC_MDIC_ERROR) {
627 hw_dbg("MDI Error\n");
628 ret_val = -IGC_ERR_PHY;
629 goto out;
630 }
631
632out:
633 return ret_val;
634}
635
636/**
637 * __igc_access_xmdio_reg - Read/write XMDIO register
638 * @hw: pointer to the HW structure
639 * @address: XMDIO address to program
640 * @dev_addr: device address to program
641 * @data: pointer to value to read/write from/to the XMDIO address
642 * @read: boolean flag to indicate read or write
643 */
644static s32 __igc_access_xmdio_reg(struct igc_hw *hw, u16 address,
645 u8 dev_addr, u16 *data, bool read)
646{
647 s32 ret_val;
648
649 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, dev_addr);
650 if (ret_val)
651 return ret_val;
652
653 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAAD, address);
654 if (ret_val)
655 return ret_val;
656
657 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, IGC_MMDAC_FUNC_DATA |
658 dev_addr);
659 if (ret_val)
660 return ret_val;
661
662 if (read)
663 ret_val = hw->phy.ops.read_reg(hw, IGC_MMDAAD, data);
664 else
665 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAAD, *data);
666 if (ret_val)
667 return ret_val;
668
669 /* Recalibrate the device back to 0 */
670 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, 0);
671 if (ret_val)
672 return ret_val;
673
674 return ret_val;
675}
676
677/**
678 * igc_read_xmdio_reg - Read XMDIO register
679 * @hw: pointer to the HW structure
680 * @addr: XMDIO address to program
681 * @dev_addr: device address to program
682 * @data: value to be read from the EMI address
683 */
684static s32 igc_read_xmdio_reg(struct igc_hw *hw, u16 addr,
685 u8 dev_addr, u16 *data)
686{
687 return __igc_access_xmdio_reg(hw, addr, dev_addr, data, true);
688}
689
690/**
691 * igc_write_xmdio_reg - Write XMDIO register
692 * @hw: pointer to the HW structure
693 * @addr: XMDIO address to program
694 * @dev_addr: device address to program
695 * @data: value to be written to the XMDIO address
696 */
697static s32 igc_write_xmdio_reg(struct igc_hw *hw, u16 addr,
698 u8 dev_addr, u16 data)
699{
700 return __igc_access_xmdio_reg(hw, addr, dev_addr, &data, false);
701}
702
703/**
704 * igc_write_phy_reg_gpy - Write GPY PHY register
705 * @hw: pointer to the HW structure
706 * @offset: register offset to write to
707 * @data: data to write at register offset
708 *
709 * Acquires semaphore, if necessary, then writes the data to PHY register
710 * at the offset. Release any acquired semaphores before exiting.
711 */
712s32 igc_write_phy_reg_gpy(struct igc_hw *hw, u32 offset, u16 data)
713{
714 u8 dev_addr = FIELD_GET(GPY_MMD_MASK, offset);
715 s32 ret_val;
716
717 offset = offset & GPY_REG_MASK;
718
719 if (!dev_addr) {
720 ret_val = hw->phy.ops.acquire(hw);
721 if (ret_val)
722 return ret_val;
723 ret_val = igc_write_phy_reg_mdic(hw, offset, data);
724 hw->phy.ops.release(hw);
725 } else {
726 ret_val = igc_write_xmdio_reg(hw, (u16)offset, dev_addr,
727 data);
728 }
729
730 return ret_val;
731}
732
733/**
734 * igc_read_phy_reg_gpy - Read GPY PHY register
735 * @hw: pointer to the HW structure
736 * @offset: lower half is register offset to read to
737 * upper half is MMD to use.
738 * @data: data to read at register offset
739 *
740 * Acquires semaphore, if necessary, then reads the data in the PHY register
741 * at the offset. Release any acquired semaphores before exiting.
742 */
743s32 igc_read_phy_reg_gpy(struct igc_hw *hw, u32 offset, u16 *data)
744{
745 u8 dev_addr = FIELD_GET(GPY_MMD_MASK, offset);
746 s32 ret_val;
747
748 offset = offset & GPY_REG_MASK;
749
750 if (!dev_addr) {
751 ret_val = hw->phy.ops.acquire(hw);
752 if (ret_val)
753 return ret_val;
754 ret_val = igc_read_phy_reg_mdic(hw, offset, data);
755 hw->phy.ops.release(hw);
756 } else {
757 ret_val = igc_read_xmdio_reg(hw, (u16)offset, dev_addr,
758 data);
759 }
760
761 return ret_val;
762}
763
764/**
765 * igc_read_phy_fw_version - Read gPHY firmware version
766 * @hw: pointer to the HW structure
767 */
768u16 igc_read_phy_fw_version(struct igc_hw *hw)
769{
770 struct igc_phy_info *phy = &hw->phy;
771 u16 gphy_version = 0;
772 u16 ret_val;
773
774 /* NVM image version is reported as firmware version for i225 device */
775 ret_val = phy->ops.read_reg(hw, IGC_GPHY_VERSION, &gphy_version);
776 if (ret_val)
777 hw_dbg("igc_phy: read wrong gphy version\n");
778
779 return gphy_version;
780}
1// SPDX-License-Identifier: GPL-2.0
2/* Copyright (c) 2018 Intel Corporation */
3
4#include "igc_phy.h"
5
6/**
7 * igc_check_reset_block - Check if PHY reset is blocked
8 * @hw: pointer to the HW structure
9 *
10 * Read the PHY management control register and check whether a PHY reset
11 * is blocked. If a reset is not blocked return 0, otherwise
12 * return IGC_ERR_BLK_PHY_RESET (12).
13 */
14s32 igc_check_reset_block(struct igc_hw *hw)
15{
16 u32 manc;
17
18 manc = rd32(IGC_MANC);
19
20 return (manc & IGC_MANC_BLK_PHY_RST_ON_IDE) ?
21 IGC_ERR_BLK_PHY_RESET : 0;
22}
23
24/**
25 * igc_get_phy_id - Retrieve the PHY ID and revision
26 * @hw: pointer to the HW structure
27 *
28 * Reads the PHY registers and stores the PHY ID and possibly the PHY
29 * revision in the hardware structure.
30 */
31s32 igc_get_phy_id(struct igc_hw *hw)
32{
33 struct igc_phy_info *phy = &hw->phy;
34 s32 ret_val = 0;
35 u16 phy_id;
36
37 ret_val = phy->ops.read_reg(hw, PHY_ID1, &phy_id);
38 if (ret_val)
39 goto out;
40
41 phy->id = (u32)(phy_id << 16);
42 usleep_range(200, 500);
43 ret_val = phy->ops.read_reg(hw, PHY_ID2, &phy_id);
44 if (ret_val)
45 goto out;
46
47 phy->id |= (u32)(phy_id & PHY_REVISION_MASK);
48 phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
49
50out:
51 return ret_val;
52}
53
54/**
55 * igc_phy_has_link - Polls PHY for link
56 * @hw: pointer to the HW structure
57 * @iterations: number of times to poll for link
58 * @usec_interval: delay between polling attempts
59 * @success: pointer to whether polling was successful or not
60 *
61 * Polls the PHY status register for link, 'iterations' number of times.
62 */
63s32 igc_phy_has_link(struct igc_hw *hw, u32 iterations,
64 u32 usec_interval, bool *success)
65{
66 u16 i, phy_status;
67 s32 ret_val = 0;
68
69 for (i = 0; i < iterations; i++) {
70 /* Some PHYs require the PHY_STATUS register to be read
71 * twice due to the link bit being sticky. No harm doing
72 * it across the board.
73 */
74 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
75 if (ret_val && usec_interval > 0) {
76 /* If the first read fails, another entity may have
77 * ownership of the resources, wait and try again to
78 * see if they have relinquished the resources yet.
79 */
80 if (usec_interval >= 1000)
81 mdelay(usec_interval / 1000);
82 else
83 udelay(usec_interval);
84 }
85 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
86 if (ret_val)
87 break;
88 if (phy_status & MII_SR_LINK_STATUS)
89 break;
90 if (usec_interval >= 1000)
91 mdelay(usec_interval / 1000);
92 else
93 udelay(usec_interval);
94 }
95
96 *success = (i < iterations) ? true : false;
97
98 return ret_val;
99}
100
101/**
102 * igc_power_up_phy_copper - Restore copper link in case of PHY power down
103 * @hw: pointer to the HW structure
104 *
105 * In the case of a PHY power down to save power, or to turn off link during a
106 * driver unload, restore the link to previous settings.
107 */
108void igc_power_up_phy_copper(struct igc_hw *hw)
109{
110 u16 mii_reg = 0;
111
112 /* The PHY will retain its settings across a power down/up cycle */
113 hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg);
114 mii_reg &= ~MII_CR_POWER_DOWN;
115 hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg);
116}
117
118/**
119 * igc_power_down_phy_copper - Power down copper PHY
120 * @hw: pointer to the HW structure
121 *
122 * Power down PHY to save power when interface is down and wake on lan
123 * is not enabled.
124 */
125void igc_power_down_phy_copper(struct igc_hw *hw)
126{
127 u16 mii_reg = 0;
128
129 /* The PHY will retain its settings across a power down/up cycle */
130 hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg);
131 mii_reg |= MII_CR_POWER_DOWN;
132
133 /* Temporary workaround - should be removed when PHY will implement
134 * IEEE registers as properly
135 */
136 /* hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg);*/
137 usleep_range(1000, 2000);
138}
139
140/**
141 * igc_check_downshift - Checks whether a downshift in speed occurred
142 * @hw: pointer to the HW structure
143 *
144 * Success returns 0, Failure returns 1
145 *
146 * A downshift is detected by querying the PHY link health.
147 */
148s32 igc_check_downshift(struct igc_hw *hw)
149{
150 struct igc_phy_info *phy = &hw->phy;
151 s32 ret_val;
152
153 switch (phy->type) {
154 case igc_phy_i225:
155 default:
156 /* speed downshift not supported */
157 phy->speed_downgraded = false;
158 ret_val = 0;
159 }
160
161 return ret_val;
162}
163
164/**
165 * igc_phy_hw_reset - PHY hardware reset
166 * @hw: pointer to the HW structure
167 *
168 * Verify the reset block is not blocking us from resetting. Acquire
169 * semaphore (if necessary) and read/set/write the device control reset
170 * bit in the PHY. Wait the appropriate delay time for the device to
171 * reset and release the semaphore (if necessary).
172 */
173s32 igc_phy_hw_reset(struct igc_hw *hw)
174{
175 struct igc_phy_info *phy = &hw->phy;
176 u32 phpm = 0, timeout = 10000;
177 s32 ret_val;
178 u32 ctrl;
179
180 ret_val = igc_check_reset_block(hw);
181 if (ret_val) {
182 ret_val = 0;
183 goto out;
184 }
185
186 ret_val = phy->ops.acquire(hw);
187 if (ret_val)
188 goto out;
189
190 phpm = rd32(IGC_I225_PHPM);
191
192 ctrl = rd32(IGC_CTRL);
193 wr32(IGC_CTRL, ctrl | IGC_CTRL_PHY_RST);
194 wrfl();
195
196 udelay(phy->reset_delay_us);
197
198 wr32(IGC_CTRL, ctrl);
199 wrfl();
200
201 /* SW should guarantee 100us for the completion of the PHY reset */
202 usleep_range(100, 150);
203 do {
204 phpm = rd32(IGC_I225_PHPM);
205 timeout--;
206 udelay(1);
207 } while (!(phpm & IGC_PHY_RST_COMP) && timeout);
208
209 if (!timeout)
210 hw_dbg("Timeout is expired after a phy reset\n");
211
212 usleep_range(100, 150);
213
214 phy->ops.release(hw);
215
216out:
217 return ret_val;
218}
219
220/**
221 * igc_phy_setup_autoneg - Configure PHY for auto-negotiation
222 * @hw: pointer to the HW structure
223 *
224 * Reads the MII auto-neg advertisement register and/or the 1000T control
225 * register and if the PHY is already setup for auto-negotiation, then
226 * return successful. Otherwise, setup advertisement and flow control to
227 * the appropriate values for the wanted auto-negotiation.
228 */
229static s32 igc_phy_setup_autoneg(struct igc_hw *hw)
230{
231 struct igc_phy_info *phy = &hw->phy;
232 u16 aneg_multigbt_an_ctrl = 0;
233 u16 mii_1000t_ctrl_reg = 0;
234 u16 mii_autoneg_adv_reg;
235 s32 ret_val;
236
237 phy->autoneg_advertised &= phy->autoneg_mask;
238
239 /* Read the MII Auto-Neg Advertisement Register (Address 4). */
240 ret_val = phy->ops.read_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
241 if (ret_val)
242 return ret_val;
243
244 if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
245 /* Read the MII 1000Base-T Control Register (Address 9). */
246 ret_val = phy->ops.read_reg(hw, PHY_1000T_CTRL,
247 &mii_1000t_ctrl_reg);
248 if (ret_val)
249 return ret_val;
250 }
251
252 if ((phy->autoneg_mask & ADVERTISE_2500_FULL) &&
253 hw->phy.id == I225_I_PHY_ID) {
254 /* Read the MULTI GBT AN Control Register - reg 7.32 */
255 ret_val = phy->ops.read_reg(hw, (STANDARD_AN_REG_MASK <<
256 MMD_DEVADDR_SHIFT) |
257 ANEG_MULTIGBT_AN_CTRL,
258 &aneg_multigbt_an_ctrl);
259
260 if (ret_val)
261 return ret_val;
262 }
263
264 /* Need to parse both autoneg_advertised and fc and set up
265 * the appropriate PHY registers. First we will parse for
266 * autoneg_advertised software override. Since we can advertise
267 * a plethora of combinations, we need to check each bit
268 * individually.
269 */
270
271 /* First we clear all the 10/100 mb speed bits in the Auto-Neg
272 * Advertisement Register (Address 4) and the 1000 mb speed bits in
273 * the 1000Base-T Control Register (Address 9).
274 */
275 mii_autoneg_adv_reg &= ~(NWAY_AR_100TX_FD_CAPS |
276 NWAY_AR_100TX_HD_CAPS |
277 NWAY_AR_10T_FD_CAPS |
278 NWAY_AR_10T_HD_CAPS);
279 mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS);
280
281 hw_dbg("autoneg_advertised %x\n", phy->autoneg_advertised);
282
283 /* Do we want to advertise 10 Mb Half Duplex? */
284 if (phy->autoneg_advertised & ADVERTISE_10_HALF) {
285 hw_dbg("Advertise 10mb Half duplex\n");
286 mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
287 }
288
289 /* Do we want to advertise 10 Mb Full Duplex? */
290 if (phy->autoneg_advertised & ADVERTISE_10_FULL) {
291 hw_dbg("Advertise 10mb Full duplex\n");
292 mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
293 }
294
295 /* Do we want to advertise 100 Mb Half Duplex? */
296 if (phy->autoneg_advertised & ADVERTISE_100_HALF) {
297 hw_dbg("Advertise 100mb Half duplex\n");
298 mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
299 }
300
301 /* Do we want to advertise 100 Mb Full Duplex? */
302 if (phy->autoneg_advertised & ADVERTISE_100_FULL) {
303 hw_dbg("Advertise 100mb Full duplex\n");
304 mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
305 }
306
307 /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
308 if (phy->autoneg_advertised & ADVERTISE_1000_HALF)
309 hw_dbg("Advertise 1000mb Half duplex request denied!\n");
310
311 /* Do we want to advertise 1000 Mb Full Duplex? */
312 if (phy->autoneg_advertised & ADVERTISE_1000_FULL) {
313 hw_dbg("Advertise 1000mb Full duplex\n");
314 mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
315 }
316
317 /* We do not allow the Phy to advertise 2500 Mb Half Duplex */
318 if (phy->autoneg_advertised & ADVERTISE_2500_HALF)
319 hw_dbg("Advertise 2500mb Half duplex request denied!\n");
320
321 /* Do we want to advertise 2500 Mb Full Duplex? */
322 if (phy->autoneg_advertised & ADVERTISE_2500_FULL) {
323 hw_dbg("Advertise 2500mb Full duplex\n");
324 aneg_multigbt_an_ctrl |= CR_2500T_FD_CAPS;
325 } else {
326 aneg_multigbt_an_ctrl &= ~CR_2500T_FD_CAPS;
327 }
328
329 /* Check for a software override of the flow control settings, and
330 * setup the PHY advertisement registers accordingly. If
331 * auto-negotiation is enabled, then software will have to set the
332 * "PAUSE" bits to the correct value in the Auto-Negotiation
333 * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-
334 * negotiation.
335 *
336 * The possible values of the "fc" parameter are:
337 * 0: Flow control is completely disabled
338 * 1: Rx flow control is enabled (we can receive pause frames
339 * but not send pause frames).
340 * 2: Tx flow control is enabled (we can send pause frames
341 * but we do not support receiving pause frames).
342 * 3: Both Rx and Tx flow control (symmetric) are enabled.
343 * other: No software override. The flow control configuration
344 * in the EEPROM is used.
345 */
346 switch (hw->fc.current_mode) {
347 case igc_fc_none:
348 /* Flow control (Rx & Tx) is completely disabled by a
349 * software over-ride.
350 */
351 mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
352 break;
353 case igc_fc_rx_pause:
354 /* Rx Flow control is enabled, and Tx Flow control is
355 * disabled, by a software over-ride.
356 *
357 * Since there really isn't a way to advertise that we are
358 * capable of Rx Pause ONLY, we will advertise that we
359 * support both symmetric and asymmetric Rx PAUSE. Later
360 * (in igc_config_fc_after_link_up) we will disable the
361 * hw's ability to send PAUSE frames.
362 */
363 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
364 break;
365 case igc_fc_tx_pause:
366 /* Tx Flow control is enabled, and Rx Flow control is
367 * disabled, by a software over-ride.
368 */
369 mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
370 mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
371 break;
372 case igc_fc_full:
373 /* Flow control (both Rx and Tx) is enabled by a software
374 * over-ride.
375 */
376 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
377 break;
378 default:
379 hw_dbg("Flow control param set incorrectly\n");
380 return -IGC_ERR_CONFIG;
381 }
382
383 ret_val = phy->ops.write_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
384 if (ret_val)
385 return ret_val;
386
387 hw_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
388
389 if (phy->autoneg_mask & ADVERTISE_1000_FULL)
390 ret_val = phy->ops.write_reg(hw, PHY_1000T_CTRL,
391 mii_1000t_ctrl_reg);
392
393 if ((phy->autoneg_mask & ADVERTISE_2500_FULL) &&
394 hw->phy.id == I225_I_PHY_ID)
395 ret_val = phy->ops.write_reg(hw,
396 (STANDARD_AN_REG_MASK <<
397 MMD_DEVADDR_SHIFT) |
398 ANEG_MULTIGBT_AN_CTRL,
399 aneg_multigbt_an_ctrl);
400
401 return ret_val;
402}
403
404/**
405 * igc_wait_autoneg - Wait for auto-neg completion
406 * @hw: pointer to the HW structure
407 *
408 * Waits for auto-negotiation to complete or for the auto-negotiation time
409 * limit to expire, which ever happens first.
410 */
411static s32 igc_wait_autoneg(struct igc_hw *hw)
412{
413 u16 i, phy_status;
414 s32 ret_val = 0;
415
416 /* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */
417 for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) {
418 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
419 if (ret_val)
420 break;
421 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
422 if (ret_val)
423 break;
424 if (phy_status & MII_SR_AUTONEG_COMPLETE)
425 break;
426 msleep(100);
427 }
428
429 /* PHY_AUTO_NEG_TIME expiration doesn't guarantee auto-negotiation
430 * has completed.
431 */
432 return ret_val;
433}
434
435/**
436 * igc_copper_link_autoneg - Setup/Enable autoneg for copper link
437 * @hw: pointer to the HW structure
438 *
439 * Performs initial bounds checking on autoneg advertisement parameter, then
440 * configure to advertise the full capability. Setup the PHY to autoneg
441 * and restart the negotiation process between the link partner. If
442 * autoneg_wait_to_complete, then wait for autoneg to complete before exiting.
443 */
444static s32 igc_copper_link_autoneg(struct igc_hw *hw)
445{
446 struct igc_phy_info *phy = &hw->phy;
447 u16 phy_ctrl;
448 s32 ret_val;
449
450 /* Perform some bounds checking on the autoneg advertisement
451 * parameter.
452 */
453 phy->autoneg_advertised &= phy->autoneg_mask;
454
455 /* If autoneg_advertised is zero, we assume it was not defaulted
456 * by the calling code so we set to advertise full capability.
457 */
458 if (phy->autoneg_advertised == 0)
459 phy->autoneg_advertised = phy->autoneg_mask;
460
461 hw_dbg("Reconfiguring auto-neg advertisement params\n");
462 ret_val = igc_phy_setup_autoneg(hw);
463 if (ret_val) {
464 hw_dbg("Error Setting up Auto-Negotiation\n");
465 goto out;
466 }
467 hw_dbg("Restarting Auto-Neg\n");
468
469 /* Restart auto-negotiation by setting the Auto Neg Enable bit and
470 * the Auto Neg Restart bit in the PHY control register.
471 */
472 ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_ctrl);
473 if (ret_val)
474 goto out;
475
476 phy_ctrl |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
477 ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_ctrl);
478 if (ret_val)
479 goto out;
480
481 /* Does the user want to wait for Auto-Neg to complete here, or
482 * check at a later time (for example, callback routine).
483 */
484 if (phy->autoneg_wait_to_complete) {
485 ret_val = igc_wait_autoneg(hw);
486 if (ret_val) {
487 hw_dbg("Error while waiting for autoneg to complete\n");
488 goto out;
489 }
490 }
491
492 hw->mac.get_link_status = true;
493
494out:
495 return ret_val;
496}
497
498/**
499 * igc_setup_copper_link - Configure copper link settings
500 * @hw: pointer to the HW structure
501 *
502 * Calls the appropriate function to configure the link for auto-neg or forced
503 * speed and duplex. Then we check for link, once link is established calls
504 * to configure collision distance and flow control are called. If link is
505 * not established, we return -IGC_ERR_PHY (-2).
506 */
507s32 igc_setup_copper_link(struct igc_hw *hw)
508{
509 s32 ret_val = 0;
510 bool link;
511
512 if (hw->mac.autoneg) {
513 /* Setup autoneg and flow control advertisement and perform
514 * autonegotiation.
515 */
516 ret_val = igc_copper_link_autoneg(hw);
517 if (ret_val)
518 goto out;
519 } else {
520 /* PHY will be set to 10H, 10F, 100H or 100F
521 * depending on user settings.
522 */
523 hw_dbg("Forcing Speed and Duplex\n");
524 ret_val = hw->phy.ops.force_speed_duplex(hw);
525 if (ret_val) {
526 hw_dbg("Error Forcing Speed and Duplex\n");
527 goto out;
528 }
529 }
530
531 /* Check link status. Wait up to 100 microseconds for link to become
532 * valid.
533 */
534 ret_val = igc_phy_has_link(hw, COPPER_LINK_UP_LIMIT, 10, &link);
535 if (ret_val)
536 goto out;
537
538 if (link) {
539 hw_dbg("Valid link established!!!\n");
540 igc_config_collision_dist(hw);
541 ret_val = igc_config_fc_after_link_up(hw);
542 } else {
543 hw_dbg("Unable to establish link!!!\n");
544 }
545
546out:
547 return ret_val;
548}
549
550/**
551 * igc_read_phy_reg_mdic - Read MDI control register
552 * @hw: pointer to the HW structure
553 * @offset: register offset to be read
554 * @data: pointer to the read data
555 *
556 * Reads the MDI control register in the PHY at offset and stores the
557 * information read to data.
558 */
559static s32 igc_read_phy_reg_mdic(struct igc_hw *hw, u32 offset, u16 *data)
560{
561 struct igc_phy_info *phy = &hw->phy;
562 u32 i, mdic = 0;
563 s32 ret_val = 0;
564
565 if (offset > MAX_PHY_REG_ADDRESS) {
566 hw_dbg("PHY Address %d is out of range\n", offset);
567 ret_val = -IGC_ERR_PARAM;
568 goto out;
569 }
570
571 /* Set up Op-code, Phy Address, and register offset in the MDI
572 * Control register. The MAC will take care of interfacing with the
573 * PHY to retrieve the desired data.
574 */
575 mdic = ((offset << IGC_MDIC_REG_SHIFT) |
576 (phy->addr << IGC_MDIC_PHY_SHIFT) |
577 (IGC_MDIC_OP_READ));
578
579 wr32(IGC_MDIC, mdic);
580
581 /* Poll the ready bit to see if the MDI read completed
582 * Increasing the time out as testing showed failures with
583 * the lower time out
584 */
585 for (i = 0; i < IGC_GEN_POLL_TIMEOUT; i++) {
586 usleep_range(500, 1000);
587 mdic = rd32(IGC_MDIC);
588 if (mdic & IGC_MDIC_READY)
589 break;
590 }
591 if (!(mdic & IGC_MDIC_READY)) {
592 hw_dbg("MDI Read did not complete\n");
593 ret_val = -IGC_ERR_PHY;
594 goto out;
595 }
596 if (mdic & IGC_MDIC_ERROR) {
597 hw_dbg("MDI Error\n");
598 ret_val = -IGC_ERR_PHY;
599 goto out;
600 }
601 *data = (u16)mdic;
602
603out:
604 return ret_val;
605}
606
607/**
608 * igc_write_phy_reg_mdic - Write MDI control register
609 * @hw: pointer to the HW structure
610 * @offset: register offset to write to
611 * @data: data to write to register at offset
612 *
613 * Writes data to MDI control register in the PHY at offset.
614 */
615static s32 igc_write_phy_reg_mdic(struct igc_hw *hw, u32 offset, u16 data)
616{
617 struct igc_phy_info *phy = &hw->phy;
618 u32 i, mdic = 0;
619 s32 ret_val = 0;
620
621 if (offset > MAX_PHY_REG_ADDRESS) {
622 hw_dbg("PHY Address %d is out of range\n", offset);
623 ret_val = -IGC_ERR_PARAM;
624 goto out;
625 }
626
627 /* Set up Op-code, Phy Address, and register offset in the MDI
628 * Control register. The MAC will take care of interfacing with the
629 * PHY to write the desired data.
630 */
631 mdic = (((u32)data) |
632 (offset << IGC_MDIC_REG_SHIFT) |
633 (phy->addr << IGC_MDIC_PHY_SHIFT) |
634 (IGC_MDIC_OP_WRITE));
635
636 wr32(IGC_MDIC, mdic);
637
638 /* Poll the ready bit to see if the MDI read completed
639 * Increasing the time out as testing showed failures with
640 * the lower time out
641 */
642 for (i = 0; i < IGC_GEN_POLL_TIMEOUT; i++) {
643 usleep_range(500, 1000);
644 mdic = rd32(IGC_MDIC);
645 if (mdic & IGC_MDIC_READY)
646 break;
647 }
648 if (!(mdic & IGC_MDIC_READY)) {
649 hw_dbg("MDI Write did not complete\n");
650 ret_val = -IGC_ERR_PHY;
651 goto out;
652 }
653 if (mdic & IGC_MDIC_ERROR) {
654 hw_dbg("MDI Error\n");
655 ret_val = -IGC_ERR_PHY;
656 goto out;
657 }
658
659out:
660 return ret_val;
661}
662
663/**
664 * __igc_access_xmdio_reg - Read/write XMDIO register
665 * @hw: pointer to the HW structure
666 * @address: XMDIO address to program
667 * @dev_addr: device address to program
668 * @data: pointer to value to read/write from/to the XMDIO address
669 * @read: boolean flag to indicate read or write
670 */
671static s32 __igc_access_xmdio_reg(struct igc_hw *hw, u16 address,
672 u8 dev_addr, u16 *data, bool read)
673{
674 s32 ret_val;
675
676 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, dev_addr);
677 if (ret_val)
678 return ret_val;
679
680 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAAD, address);
681 if (ret_val)
682 return ret_val;
683
684 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, IGC_MMDAC_FUNC_DATA |
685 dev_addr);
686 if (ret_val)
687 return ret_val;
688
689 if (read)
690 ret_val = hw->phy.ops.read_reg(hw, IGC_MMDAAD, data);
691 else
692 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAAD, *data);
693 if (ret_val)
694 return ret_val;
695
696 /* Recalibrate the device back to 0 */
697 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, 0);
698 if (ret_val)
699 return ret_val;
700
701 return ret_val;
702}
703
704/**
705 * igc_read_xmdio_reg - Read XMDIO register
706 * @hw: pointer to the HW structure
707 * @addr: XMDIO address to program
708 * @dev_addr: device address to program
709 * @data: value to be read from the EMI address
710 */
711static s32 igc_read_xmdio_reg(struct igc_hw *hw, u16 addr,
712 u8 dev_addr, u16 *data)
713{
714 return __igc_access_xmdio_reg(hw, addr, dev_addr, data, true);
715}
716
717/**
718 * igc_write_xmdio_reg - Write XMDIO register
719 * @hw: pointer to the HW structure
720 * @addr: XMDIO address to program
721 * @dev_addr: device address to program
722 * @data: value to be written to the XMDIO address
723 */
724static s32 igc_write_xmdio_reg(struct igc_hw *hw, u16 addr,
725 u8 dev_addr, u16 data)
726{
727 return __igc_access_xmdio_reg(hw, addr, dev_addr, &data, false);
728}
729
730/**
731 * igc_write_phy_reg_gpy - Write GPY PHY register
732 * @hw: pointer to the HW structure
733 * @offset: register offset to write to
734 * @data: data to write at register offset
735 *
736 * Acquires semaphore, if necessary, then writes the data to PHY register
737 * at the offset. Release any acquired semaphores before exiting.
738 */
739s32 igc_write_phy_reg_gpy(struct igc_hw *hw, u32 offset, u16 data)
740{
741 u8 dev_addr = (offset & GPY_MMD_MASK) >> GPY_MMD_SHIFT;
742 s32 ret_val;
743
744 offset = offset & GPY_REG_MASK;
745
746 if (!dev_addr) {
747 ret_val = hw->phy.ops.acquire(hw);
748 if (ret_val)
749 return ret_val;
750 ret_val = igc_write_phy_reg_mdic(hw, offset, data);
751 if (ret_val)
752 return ret_val;
753 hw->phy.ops.release(hw);
754 } else {
755 ret_val = igc_write_xmdio_reg(hw, (u16)offset, dev_addr,
756 data);
757 }
758
759 return ret_val;
760}
761
762/**
763 * igc_read_phy_reg_gpy - Read GPY PHY register
764 * @hw: pointer to the HW structure
765 * @offset: lower half is register offset to read to
766 * upper half is MMD to use.
767 * @data: data to read at register offset
768 *
769 * Acquires semaphore, if necessary, then reads the data in the PHY register
770 * at the offset. Release any acquired semaphores before exiting.
771 */
772s32 igc_read_phy_reg_gpy(struct igc_hw *hw, u32 offset, u16 *data)
773{
774 u8 dev_addr = (offset & GPY_MMD_MASK) >> GPY_MMD_SHIFT;
775 s32 ret_val;
776
777 offset = offset & GPY_REG_MASK;
778
779 if (!dev_addr) {
780 ret_val = hw->phy.ops.acquire(hw);
781 if (ret_val)
782 return ret_val;
783 ret_val = igc_read_phy_reg_mdic(hw, offset, data);
784 if (ret_val)
785 return ret_val;
786 hw->phy.ops.release(hw);
787 } else {
788 ret_val = igc_read_xmdio_reg(hw, (u16)offset, dev_addr,
789 data);
790 }
791
792 return ret_val;
793}
794
795/**
796 * igc_read_phy_fw_version - Read gPHY firmware version
797 * @hw: pointer to the HW structure
798 */
799u16 igc_read_phy_fw_version(struct igc_hw *hw)
800{
801 struct igc_phy_info *phy = &hw->phy;
802 u16 gphy_version = 0;
803 u16 ret_val;
804
805 /* NVM image version is reported as firmware version for i225 device */
806 ret_val = phy->ops.read_reg(hw, IGC_GPHY_VERSION, &gphy_version);
807 if (ret_val)
808 hw_dbg("igc_phy: read wrong gphy version\n");
809
810 return gphy_version;
811}