Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Copyright (C) 2008-2010 Pavel Cheblakov <P.B.Cheblakov@inp.nsk.su>
4 *
5 * Derived from the ems_pci.c driver:
6 * Copyright (C) 2007 Wolfgang Grandegger <wg@grandegger.com>
7 * Copyright (C) 2008 Markus Plessing <plessing@ems-wuensche.com>
8 * Copyright (C) 2008 Sebastian Haas <haas@ems-wuensche.com>
9 */
10
11#include <linux/kernel.h>
12#include <linux/module.h>
13#include <linux/interrupt.h>
14#include <linux/netdevice.h>
15#include <linux/delay.h>
16#include <linux/slab.h>
17#include <linux/pci.h>
18#include <linux/can/dev.h>
19#include <linux/io.h>
20
21#include "sja1000.h"
22
23#define DRV_NAME "sja1000_plx_pci"
24
25MODULE_AUTHOR("Pavel Cheblakov <P.B.Cheblakov@inp.nsk.su>");
26MODULE_DESCRIPTION("Socket-CAN driver for PLX90xx PCI-bridge cards with "
27 "the SJA1000 chips");
28MODULE_LICENSE("GPL v2");
29
30#define PLX_PCI_MAX_CHAN 2
31
32struct plx_pci_card {
33 int channels; /* detected channels count */
34 struct net_device *net_dev[PLX_PCI_MAX_CHAN];
35 void __iomem *conf_addr;
36
37 /* Pointer to device-dependent reset function */
38 void (*reset_func)(struct pci_dev *pdev);
39};
40
41#define PLX_PCI_CAN_CLOCK (16000000 / 2)
42
43/* PLX9030/9050/9052 registers */
44#define PLX_INTCSR 0x4c /* Interrupt Control/Status */
45#define PLX_CNTRL 0x50 /* User I/O, Direct Slave Response,
46 * Serial EEPROM, and Initialization
47 * Control register
48 */
49
50#define PLX_LINT1_EN 0x1 /* Local interrupt 1 enable */
51#define PLX_LINT1_POL (1 << 1) /* Local interrupt 1 polarity */
52#define PLX_LINT2_EN (1 << 3) /* Local interrupt 2 enable */
53#define PLX_LINT2_POL (1 << 4) /* Local interrupt 2 polarity */
54#define PLX_PCI_INT_EN (1 << 6) /* PCI Interrupt Enable */
55#define PLX_PCI_RESET (1 << 30) /* PCI Adapter Software Reset */
56
57/* PLX9056 registers */
58#define PLX9056_INTCSR 0x68 /* Interrupt Control/Status */
59#define PLX9056_CNTRL 0x6c /* Control / Software Reset */
60
61#define PLX9056_LINTI (1 << 11)
62#define PLX9056_PCI_INT_EN (1 << 8)
63#define PLX9056_PCI_RCR (1 << 29) /* Read Configuration Registers */
64
65/*
66 * The board configuration is probably following:
67 * RX1 is connected to ground.
68 * TX1 is not connected.
69 * CLKO is not connected.
70 * Setting the OCR register to 0xDA is a good idea.
71 * This means normal output mode, push-pull and the correct polarity.
72 */
73#define PLX_PCI_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
74
75/* OCR setting for ASEM Dual CAN raw */
76#define ASEM_PCI_OCR 0xfe
77
78/*
79 * In the CDR register, you should set CBP to 1.
80 * You will probably also want to set the clock divider value to 7
81 * (meaning direct oscillator output) because the second SJA1000 chip
82 * is driven by the first one CLKOUT output.
83 */
84#define PLX_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
85
86/* SJA1000 Control Register in the BasicCAN Mode */
87#define REG_CR 0x00
88
89/* States of some SJA1000 registers after hardware reset in the BasicCAN mode*/
90#define REG_CR_BASICCAN_INITIAL 0x21
91#define REG_CR_BASICCAN_INITIAL_MASK 0xa1
92#define REG_SR_BASICCAN_INITIAL 0x0c
93#define REG_IR_BASICCAN_INITIAL 0xe0
94
95/* States of some SJA1000 registers after hardware reset in the PeliCAN mode*/
96#define REG_MOD_PELICAN_INITIAL 0x01
97#define REG_SR_PELICAN_INITIAL 0x3c
98#define REG_IR_PELICAN_INITIAL 0x00
99
100#define ADLINK_PCI_VENDOR_ID 0x144A
101#define ADLINK_PCI_DEVICE_ID 0x7841
102
103#define ESD_PCI_SUB_SYS_ID_PCI200 0x0004
104#define ESD_PCI_SUB_SYS_ID_PCI266 0x0009
105#define ESD_PCI_SUB_SYS_ID_PMC266 0x000e
106#define ESD_PCI_SUB_SYS_ID_CPCI200 0x010b
107#define ESD_PCI_SUB_SYS_ID_PCIE2000 0x0200
108#define ESD_PCI_SUB_SYS_ID_PCI104200 0x0501
109
110#define CAN200PCI_DEVICE_ID 0x9030
111#define CAN200PCI_VENDOR_ID 0x10b5
112#define CAN200PCI_SUB_DEVICE_ID 0x0301
113#define CAN200PCI_SUB_VENDOR_ID 0xe1c5
114
115#define IXXAT_PCI_VENDOR_ID 0x10b5
116#define IXXAT_PCI_DEVICE_ID 0x9050
117#define IXXAT_PCI_SUB_SYS_ID 0x2540
118
119#define MARATHON_PCI_DEVICE_ID 0x2715
120#define MARATHON_PCIE_DEVICE_ID 0x3432
121
122#define TEWS_PCI_VENDOR_ID 0x1498
123#define TEWS_PCI_DEVICE_ID_TMPC810 0x032A
124
125#define CTI_PCI_DEVICE_ID_CRG001 0x0900
126
127#define MOXA_PCI_VENDOR_ID 0x1393
128#define MOXA_PCI_DEVICE_ID 0x0100
129
130#define ASEM_RAW_CAN_VENDOR_ID 0x10b5
131#define ASEM_RAW_CAN_DEVICE_ID 0x9030
132#define ASEM_RAW_CAN_SUB_VENDOR_ID 0x3000
133#define ASEM_RAW_CAN_SUB_DEVICE_ID 0x1001
134#define ASEM_RAW_CAN_SUB_DEVICE_ID_BIS 0x1002
135#define ASEM_RAW_CAN_RST_REGISTER 0x54
136#define ASEM_RAW_CAN_RST_MASK_CAN1 0x20
137#define ASEM_RAW_CAN_RST_MASK_CAN2 0x04
138
139static void plx_pci_reset_common(struct pci_dev *pdev);
140static void plx9056_pci_reset_common(struct pci_dev *pdev);
141static void plx_pci_reset_marathon_pci(struct pci_dev *pdev);
142static void plx_pci_reset_marathon_pcie(struct pci_dev *pdev);
143static void plx_pci_reset_asem_dual_can_raw(struct pci_dev *pdev);
144
145struct plx_pci_channel_map {
146 u32 bar;
147 u32 offset;
148 u32 size; /* 0x00 - auto, e.g. length of entire bar */
149};
150
151struct plx_pci_card_info {
152 const char *name;
153 int channel_count;
154 u32 can_clock;
155 u8 ocr; /* output control register */
156 u8 cdr; /* clock divider register */
157
158 /* Parameters for mapping local configuration space */
159 struct plx_pci_channel_map conf_map;
160
161 /* Parameters for mapping the SJA1000 chips */
162 struct plx_pci_channel_map chan_map_tbl[PLX_PCI_MAX_CHAN];
163
164 /* Pointer to device-dependent reset function */
165 void (*reset_func)(struct pci_dev *pdev);
166};
167
168static struct plx_pci_card_info plx_pci_card_info_adlink = {
169 "Adlink PCI-7841/cPCI-7841", 2,
170 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
171 {1, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x80, 0x80} },
172 &plx_pci_reset_common
173 /* based on PLX9052 */
174};
175
176static struct plx_pci_card_info plx_pci_card_info_adlink_se = {
177 "Adlink PCI-7841/cPCI-7841 SE", 2,
178 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
179 {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x80, 0x80} },
180 &plx_pci_reset_common
181 /* based on PLX9052 */
182};
183
184static struct plx_pci_card_info plx_pci_card_info_esd200 = {
185 "esd CAN-PCI/CPCI/PCI104/200", 2,
186 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
187 {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
188 &plx_pci_reset_common
189 /* based on PLX9030/9050 */
190};
191
192static struct plx_pci_card_info plx_pci_card_info_esd266 = {
193 "esd CAN-PCI/PMC/266", 2,
194 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
195 {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
196 &plx9056_pci_reset_common
197 /* based on PLX9056 */
198};
199
200static struct plx_pci_card_info plx_pci_card_info_esd2000 = {
201 "esd CAN-PCIe/2000", 2,
202 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
203 {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
204 &plx9056_pci_reset_common
205 /* based on PEX8311 */
206};
207
208static struct plx_pci_card_info plx_pci_card_info_ixxat = {
209 "IXXAT PC-I 04/PCI", 2,
210 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
211 {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x200, 0x80} },
212 &plx_pci_reset_common
213 /* based on PLX9050 */
214};
215
216static struct plx_pci_card_info plx_pci_card_info_marathon_pci = {
217 "Marathon CAN-bus-PCI", 2,
218 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
219 {0, 0x00, 0x00}, { {2, 0x00, 0x00}, {4, 0x00, 0x00} },
220 &plx_pci_reset_marathon_pci
221 /* based on PLX9052 */
222};
223
224static struct plx_pci_card_info plx_pci_card_info_marathon_pcie = {
225 "Marathon CAN-bus-PCIe", 2,
226 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
227 {0, 0x00, 0x00}, { {2, 0x00, 0x00}, {3, 0x80, 0x00} },
228 &plx_pci_reset_marathon_pcie
229 /* based on PEX8311 */
230};
231
232static struct plx_pci_card_info plx_pci_card_info_tews = {
233 "TEWS TECHNOLOGIES TPMC810", 2,
234 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
235 {0, 0x00, 0x00}, { {2, 0x000, 0x80}, {2, 0x100, 0x80} },
236 &plx_pci_reset_common
237 /* based on PLX9030 */
238};
239
240static struct plx_pci_card_info plx_pci_card_info_cti = {
241 "Connect Tech Inc. CANpro/104-Plus Opto (CRG001)", 2,
242 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
243 {0, 0x00, 0x00}, { {2, 0x000, 0x80}, {2, 0x100, 0x80} },
244 &plx_pci_reset_common
245 /* based on PLX9030 */
246};
247
248static struct plx_pci_card_info plx_pci_card_info_elcus = {
249 "Eclus CAN-200-PCI", 2,
250 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
251 {1, 0x00, 0x00}, { {2, 0x00, 0x80}, {3, 0x00, 0x80} },
252 &plx_pci_reset_common
253 /* based on PLX9030 */
254};
255
256static struct plx_pci_card_info plx_pci_card_info_moxa = {
257 "MOXA", 2,
258 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
259 {0, 0x00, 0x00}, { {0, 0x00, 0x80}, {1, 0x00, 0x80} },
260 &plx_pci_reset_common
261 /* based on PLX9052 */
262};
263
264static struct plx_pci_card_info plx_pci_card_info_asem_dual_can = {
265 "ASEM Dual CAN raw PCI", 2,
266 PLX_PCI_CAN_CLOCK, ASEM_PCI_OCR, PLX_PCI_CDR,
267 {0, 0x00, 0x00}, { {2, 0x00, 0x00}, {4, 0x00, 0x00} },
268 &plx_pci_reset_asem_dual_can_raw
269 /* based on PLX9030 */
270};
271
272static const struct pci_device_id plx_pci_tbl[] = {
273 {
274 /* Adlink PCI-7841/cPCI-7841 */
275 ADLINK_PCI_VENDOR_ID, ADLINK_PCI_DEVICE_ID,
276 PCI_ANY_ID, PCI_ANY_ID,
277 PCI_CLASS_NETWORK_OTHER << 8, ~0,
278 (kernel_ulong_t)&plx_pci_card_info_adlink
279 },
280 {
281 /* Adlink PCI-7841/cPCI-7841 SE */
282 ADLINK_PCI_VENDOR_ID, ADLINK_PCI_DEVICE_ID,
283 PCI_ANY_ID, PCI_ANY_ID,
284 PCI_CLASS_COMMUNICATION_OTHER << 8, ~0,
285 (kernel_ulong_t)&plx_pci_card_info_adlink_se
286 },
287 {
288 /* esd CAN-PCI/200 */
289 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
290 PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI200,
291 0, 0,
292 (kernel_ulong_t)&plx_pci_card_info_esd200
293 },
294 {
295 /* esd CAN-CPCI/200 */
296 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
297 PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_CPCI200,
298 0, 0,
299 (kernel_ulong_t)&plx_pci_card_info_esd200
300 },
301 {
302 /* esd CAN-PCI104/200 */
303 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
304 PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI104200,
305 0, 0,
306 (kernel_ulong_t)&plx_pci_card_info_esd200
307 },
308 {
309 /* esd CAN-PCI/266 */
310 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
311 PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI266,
312 0, 0,
313 (kernel_ulong_t)&plx_pci_card_info_esd266
314 },
315 {
316 /* esd CAN-PMC/266 */
317 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
318 PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PMC266,
319 0, 0,
320 (kernel_ulong_t)&plx_pci_card_info_esd266
321 },
322 {
323 /* esd CAN-PCIE/2000 */
324 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
325 PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCIE2000,
326 0, 0,
327 (kernel_ulong_t)&plx_pci_card_info_esd2000
328 },
329 {
330 /* IXXAT PC-I 04/PCI card */
331 IXXAT_PCI_VENDOR_ID, IXXAT_PCI_DEVICE_ID,
332 PCI_ANY_ID, IXXAT_PCI_SUB_SYS_ID,
333 0, 0,
334 (kernel_ulong_t)&plx_pci_card_info_ixxat
335 },
336 {
337 /* Marathon CAN-bus-PCI card */
338 PCI_VENDOR_ID_PLX, MARATHON_PCI_DEVICE_ID,
339 PCI_ANY_ID, PCI_ANY_ID,
340 0, 0,
341 (kernel_ulong_t)&plx_pci_card_info_marathon_pci
342 },
343 {
344 /* Marathon CAN-bus-PCIe card */
345 PCI_VENDOR_ID_PLX, MARATHON_PCIE_DEVICE_ID,
346 PCI_ANY_ID, PCI_ANY_ID,
347 0, 0,
348 (kernel_ulong_t)&plx_pci_card_info_marathon_pcie
349 },
350 {
351 /* TEWS TECHNOLOGIES TPMC810 card */
352 TEWS_PCI_VENDOR_ID, TEWS_PCI_DEVICE_ID_TMPC810,
353 PCI_ANY_ID, PCI_ANY_ID,
354 0, 0,
355 (kernel_ulong_t)&plx_pci_card_info_tews
356 },
357 {
358 /* Connect Tech Inc. CANpro/104-Plus Opto (CRG001) card */
359 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
360 PCI_SUBVENDOR_ID_CONNECT_TECH, CTI_PCI_DEVICE_ID_CRG001,
361 0, 0,
362 (kernel_ulong_t)&plx_pci_card_info_cti
363 },
364 {
365 /* Elcus CAN-200-PCI */
366 CAN200PCI_VENDOR_ID, CAN200PCI_DEVICE_ID,
367 CAN200PCI_SUB_VENDOR_ID, CAN200PCI_SUB_DEVICE_ID,
368 0, 0,
369 (kernel_ulong_t)&plx_pci_card_info_elcus
370 },
371 {
372 /* moxa */
373 MOXA_PCI_VENDOR_ID, MOXA_PCI_DEVICE_ID,
374 PCI_ANY_ID, PCI_ANY_ID,
375 0, 0,
376 (kernel_ulong_t)&plx_pci_card_info_moxa
377 },
378 {
379 /* ASEM Dual CAN raw */
380 ASEM_RAW_CAN_VENDOR_ID, ASEM_RAW_CAN_DEVICE_ID,
381 ASEM_RAW_CAN_SUB_VENDOR_ID, ASEM_RAW_CAN_SUB_DEVICE_ID,
382 0, 0,
383 (kernel_ulong_t)&plx_pci_card_info_asem_dual_can
384 },
385 {
386 /* ASEM Dual CAN raw -new model */
387 ASEM_RAW_CAN_VENDOR_ID, ASEM_RAW_CAN_DEVICE_ID,
388 ASEM_RAW_CAN_SUB_VENDOR_ID, ASEM_RAW_CAN_SUB_DEVICE_ID_BIS,
389 0, 0,
390 (kernel_ulong_t)&plx_pci_card_info_asem_dual_can
391 },
392 { 0,}
393};
394MODULE_DEVICE_TABLE(pci, plx_pci_tbl);
395
396static u8 plx_pci_read_reg(const struct sja1000_priv *priv, int port)
397{
398 return ioread8(priv->reg_base + port);
399}
400
401static void plx_pci_write_reg(const struct sja1000_priv *priv, int port, u8 val)
402{
403 iowrite8(val, priv->reg_base + port);
404}
405
406/*
407 * Check if a CAN controller is present at the specified location
408 * by trying to switch 'em from the Basic mode into the PeliCAN mode.
409 * Also check states of some registers in reset mode.
410 */
411static inline int plx_pci_check_sja1000(const struct sja1000_priv *priv)
412{
413 int flag = 0;
414
415 /*
416 * Check registers after hardware reset (the Basic mode)
417 * See states on p. 10 of the Datasheet.
418 */
419 if ((priv->read_reg(priv, REG_CR) & REG_CR_BASICCAN_INITIAL_MASK) ==
420 REG_CR_BASICCAN_INITIAL &&
421 (priv->read_reg(priv, SJA1000_SR) == REG_SR_BASICCAN_INITIAL) &&
422 (priv->read_reg(priv, SJA1000_IR) == REG_IR_BASICCAN_INITIAL))
423 flag = 1;
424
425 /* Bring the SJA1000 into the PeliCAN mode*/
426 priv->write_reg(priv, SJA1000_CDR, CDR_PELICAN);
427
428 /*
429 * Check registers after reset in the PeliCAN mode.
430 * See states on p. 23 of the Datasheet.
431 */
432 if (priv->read_reg(priv, SJA1000_MOD) == REG_MOD_PELICAN_INITIAL &&
433 priv->read_reg(priv, SJA1000_SR) == REG_SR_PELICAN_INITIAL &&
434 priv->read_reg(priv, SJA1000_IR) == REG_IR_PELICAN_INITIAL)
435 return flag;
436
437 return 0;
438}
439
440/*
441 * PLX9030/50/52 software reset
442 * Also LRESET# asserts and brings to reset device on the Local Bus (if wired).
443 * For most cards it's enough for reset the SJA1000 chips.
444 */
445static void plx_pci_reset_common(struct pci_dev *pdev)
446{
447 struct plx_pci_card *card = pci_get_drvdata(pdev);
448 u32 cntrl;
449
450 cntrl = ioread32(card->conf_addr + PLX_CNTRL);
451 cntrl |= PLX_PCI_RESET;
452 iowrite32(cntrl, card->conf_addr + PLX_CNTRL);
453 udelay(100);
454 cntrl ^= PLX_PCI_RESET;
455 iowrite32(cntrl, card->conf_addr + PLX_CNTRL);
456};
457
458/*
459 * PLX9056 software reset
460 * Assert LRESET# and reset device(s) on the Local Bus (if wired).
461 */
462static void plx9056_pci_reset_common(struct pci_dev *pdev)
463{
464 struct plx_pci_card *card = pci_get_drvdata(pdev);
465 u32 cntrl;
466
467 /* issue a local bus reset */
468 cntrl = ioread32(card->conf_addr + PLX9056_CNTRL);
469 cntrl |= PLX_PCI_RESET;
470 iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
471 udelay(100);
472 cntrl ^= PLX_PCI_RESET;
473 iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
474
475 /* reload local configuration from EEPROM */
476 cntrl |= PLX9056_PCI_RCR;
477 iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
478
479 /*
480 * There is no safe way to poll for the end
481 * of reconfiguration process. Waiting for 10ms
482 * is safe.
483 */
484 mdelay(10);
485
486 cntrl ^= PLX9056_PCI_RCR;
487 iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
488};
489
490/* Special reset function for Marathon CAN-bus-PCI card */
491static void plx_pci_reset_marathon_pci(struct pci_dev *pdev)
492{
493 void __iomem *reset_addr;
494 int i;
495 static const int reset_bar[2] = {3, 5};
496
497 plx_pci_reset_common(pdev);
498
499 for (i = 0; i < 2; i++) {
500 reset_addr = pci_iomap(pdev, reset_bar[i], 0);
501 if (!reset_addr) {
502 dev_err(&pdev->dev, "Failed to remap reset "
503 "space %d (BAR%d)\n", i, reset_bar[i]);
504 } else {
505 /* reset the SJA1000 chip */
506 iowrite8(0x1, reset_addr);
507 udelay(100);
508 pci_iounmap(pdev, reset_addr);
509 }
510 }
511}
512
513/* Special reset function for Marathon CAN-bus-PCIe card */
514static void plx_pci_reset_marathon_pcie(struct pci_dev *pdev)
515{
516 void __iomem *addr;
517 void __iomem *reset_addr;
518 int i;
519
520 plx9056_pci_reset_common(pdev);
521
522 for (i = 0; i < 2; i++) {
523 struct plx_pci_channel_map *chan_map =
524 &plx_pci_card_info_marathon_pcie.chan_map_tbl[i];
525 addr = pci_iomap(pdev, chan_map->bar, chan_map->size);
526 if (!addr) {
527 dev_err(&pdev->dev, "Failed to remap reset "
528 "space %d (BAR%d)\n", i, chan_map->bar);
529 } else {
530 /* reset the SJA1000 chip */
531 #define MARATHON_PCIE_RESET_OFFSET 32
532 reset_addr = addr + chan_map->offset +
533 MARATHON_PCIE_RESET_OFFSET;
534 iowrite8(0x1, reset_addr);
535 udelay(100);
536 pci_iounmap(pdev, addr);
537 }
538 }
539}
540
541/* Special reset function for ASEM Dual CAN raw card */
542static void plx_pci_reset_asem_dual_can_raw(struct pci_dev *pdev)
543{
544 void __iomem *bar0_addr;
545 u8 tmpval;
546
547 plx_pci_reset_common(pdev);
548
549 bar0_addr = pci_iomap(pdev, 0, 0);
550 if (!bar0_addr) {
551 dev_err(&pdev->dev, "Failed to remap reset space 0 (BAR0)\n");
552 return;
553 }
554
555 /* reset the two SJA1000 chips */
556 tmpval = ioread8(bar0_addr + ASEM_RAW_CAN_RST_REGISTER);
557 tmpval &= ~(ASEM_RAW_CAN_RST_MASK_CAN1 | ASEM_RAW_CAN_RST_MASK_CAN2);
558 iowrite8(tmpval, bar0_addr + ASEM_RAW_CAN_RST_REGISTER);
559 usleep_range(300, 400);
560 tmpval |= ASEM_RAW_CAN_RST_MASK_CAN1 | ASEM_RAW_CAN_RST_MASK_CAN2;
561 iowrite8(tmpval, bar0_addr + ASEM_RAW_CAN_RST_REGISTER);
562 usleep_range(300, 400);
563 pci_iounmap(pdev, bar0_addr);
564}
565
566static void plx_pci_del_card(struct pci_dev *pdev)
567{
568 struct plx_pci_card *card = pci_get_drvdata(pdev);
569 struct net_device *dev;
570 struct sja1000_priv *priv;
571 int i = 0;
572
573 for (i = 0; i < PLX_PCI_MAX_CHAN; i++) {
574 dev = card->net_dev[i];
575 if (!dev)
576 continue;
577
578 dev_info(&pdev->dev, "Removing %s\n", dev->name);
579 unregister_sja1000dev(dev);
580 priv = netdev_priv(dev);
581 if (priv->reg_base)
582 pci_iounmap(pdev, priv->reg_base);
583 free_sja1000dev(dev);
584 }
585
586 card->reset_func(pdev);
587
588 /*
589 * Disable interrupts from PCI-card and disable local
590 * interrupts
591 */
592 if (pdev->device != PCI_DEVICE_ID_PLX_9056 &&
593 pdev->device != MARATHON_PCIE_DEVICE_ID)
594 iowrite32(0x0, card->conf_addr + PLX_INTCSR);
595 else
596 iowrite32(0x0, card->conf_addr + PLX9056_INTCSR);
597
598 if (card->conf_addr)
599 pci_iounmap(pdev, card->conf_addr);
600
601 kfree(card);
602
603 pci_disable_device(pdev);
604}
605
606/*
607 * Probe PLX90xx based device for the SJA1000 chips and register each
608 * available CAN channel to SJA1000 Socket-CAN subsystem.
609 */
610static int plx_pci_add_card(struct pci_dev *pdev,
611 const struct pci_device_id *ent)
612{
613 struct sja1000_priv *priv;
614 struct net_device *dev;
615 struct plx_pci_card *card;
616 struct plx_pci_card_info *ci;
617 int err, i;
618 u32 val;
619 void __iomem *addr;
620
621 ci = (struct plx_pci_card_info *)ent->driver_data;
622
623 if (pci_enable_device(pdev) < 0) {
624 dev_err(&pdev->dev, "Failed to enable PCI device\n");
625 return -ENODEV;
626 }
627
628 dev_info(&pdev->dev, "Detected \"%s\" card at slot #%i\n",
629 ci->name, PCI_SLOT(pdev->devfn));
630
631 /* Allocate card structures to hold addresses, ... */
632 card = kzalloc(sizeof(*card), GFP_KERNEL);
633 if (!card) {
634 pci_disable_device(pdev);
635 return -ENOMEM;
636 }
637
638 pci_set_drvdata(pdev, card);
639
640 card->channels = 0;
641
642 /* Remap PLX90xx configuration space */
643 addr = pci_iomap(pdev, ci->conf_map.bar, ci->conf_map.size);
644 if (!addr) {
645 err = -ENOMEM;
646 dev_err(&pdev->dev, "Failed to remap configuration space "
647 "(BAR%d)\n", ci->conf_map.bar);
648 goto failure_cleanup;
649 }
650 card->conf_addr = addr + ci->conf_map.offset;
651
652 ci->reset_func(pdev);
653 card->reset_func = ci->reset_func;
654
655 /* Detect available channels */
656 for (i = 0; i < ci->channel_count; i++) {
657 struct plx_pci_channel_map *cm = &ci->chan_map_tbl[i];
658
659 dev = alloc_sja1000dev(0);
660 if (!dev) {
661 err = -ENOMEM;
662 goto failure_cleanup;
663 }
664
665 card->net_dev[i] = dev;
666 priv = netdev_priv(dev);
667 priv->priv = card;
668 priv->irq_flags = IRQF_SHARED;
669
670 dev->irq = pdev->irq;
671
672 /*
673 * Remap IO space of the SJA1000 chips
674 * This is device-dependent mapping
675 */
676 addr = pci_iomap(pdev, cm->bar, cm->size);
677 if (!addr) {
678 err = -ENOMEM;
679 dev_err(&pdev->dev, "Failed to remap BAR%d\n", cm->bar);
680 goto failure_cleanup;
681 }
682
683 priv->reg_base = addr + cm->offset;
684 priv->read_reg = plx_pci_read_reg;
685 priv->write_reg = plx_pci_write_reg;
686
687 /* Check if channel is present */
688 if (plx_pci_check_sja1000(priv)) {
689 priv->can.clock.freq = ci->can_clock;
690 priv->ocr = ci->ocr;
691 priv->cdr = ci->cdr;
692
693 SET_NETDEV_DEV(dev, &pdev->dev);
694 dev->dev_id = i;
695
696 /* Register SJA1000 device */
697 err = register_sja1000dev(dev);
698 if (err) {
699 dev_err(&pdev->dev, "Registering device failed "
700 "(err=%d)\n", err);
701 goto failure_cleanup;
702 }
703
704 card->channels++;
705
706 dev_info(&pdev->dev, "Channel #%d at 0x%p, irq %d "
707 "registered as %s\n", i + 1, priv->reg_base,
708 dev->irq, dev->name);
709 } else {
710 dev_err(&pdev->dev, "Channel #%d not detected\n",
711 i + 1);
712 free_sja1000dev(dev);
713 card->net_dev[i] = NULL;
714 }
715 }
716
717 if (!card->channels) {
718 err = -ENODEV;
719 goto failure_cleanup;
720 }
721
722 /*
723 * Enable interrupts from PCI-card (PLX90xx) and enable Local_1,
724 * Local_2 interrupts from the SJA1000 chips
725 */
726 if (pdev->device != PCI_DEVICE_ID_PLX_9056 &&
727 pdev->device != MARATHON_PCIE_DEVICE_ID) {
728 val = ioread32(card->conf_addr + PLX_INTCSR);
729 if (pdev->subsystem_vendor == PCI_VENDOR_ID_ESDGMBH)
730 val |= PLX_LINT1_EN | PLX_PCI_INT_EN;
731 else
732 val |= PLX_LINT1_EN | PLX_LINT2_EN | PLX_PCI_INT_EN;
733 iowrite32(val, card->conf_addr + PLX_INTCSR);
734 } else {
735 iowrite32(PLX9056_LINTI | PLX9056_PCI_INT_EN,
736 card->conf_addr + PLX9056_INTCSR);
737 }
738 return 0;
739
740failure_cleanup:
741 dev_err(&pdev->dev, "Error: %d. Cleaning Up.\n", err);
742
743 plx_pci_del_card(pdev);
744
745 return err;
746}
747
748static struct pci_driver plx_pci_driver = {
749 .name = DRV_NAME,
750 .id_table = plx_pci_tbl,
751 .probe = plx_pci_add_card,
752 .remove = plx_pci_del_card,
753};
754
755module_pci_driver(plx_pci_driver);
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Copyright (C) 2008-2010 Pavel Cheblakov <P.B.Cheblakov@inp.nsk.su>
4 *
5 * Derived from the ems_pci.c driver:
6 * Copyright (C) 2007 Wolfgang Grandegger <wg@grandegger.com>
7 * Copyright (C) 2008 Markus Plessing <plessing@ems-wuensche.com>
8 * Copyright (C) 2008 Sebastian Haas <haas@ems-wuensche.com>
9 */
10
11#include <linux/kernel.h>
12#include <linux/module.h>
13#include <linux/interrupt.h>
14#include <linux/netdevice.h>
15#include <linux/delay.h>
16#include <linux/slab.h>
17#include <linux/pci.h>
18#include <linux/can/dev.h>
19#include <linux/io.h>
20
21#include "sja1000.h"
22
23#define DRV_NAME "sja1000_plx_pci"
24
25MODULE_AUTHOR("Pavel Cheblakov <P.B.Cheblakov@inp.nsk.su>");
26MODULE_DESCRIPTION("Socket-CAN driver for PLX90xx PCI-bridge cards with "
27 "the SJA1000 chips");
28MODULE_LICENSE("GPL v2");
29
30#define PLX_PCI_MAX_CHAN 2
31
32struct plx_pci_card {
33 int channels; /* detected channels count */
34 struct net_device *net_dev[PLX_PCI_MAX_CHAN];
35 void __iomem *conf_addr;
36
37 /* Pointer to device-dependent reset function */
38 void (*reset_func)(struct pci_dev *pdev);
39};
40
41#define PLX_PCI_CAN_CLOCK (16000000 / 2)
42
43/* PLX9030/9050/9052 registers */
44#define PLX_INTCSR 0x4c /* Interrupt Control/Status */
45#define PLX_CNTRL 0x50 /* User I/O, Direct Slave Response,
46 * Serial EEPROM, and Initialization
47 * Control register
48 */
49
50#define PLX_LINT1_EN 0x1 /* Local interrupt 1 enable */
51#define PLX_LINT1_POL (1 << 1) /* Local interrupt 1 polarity */
52#define PLX_LINT2_EN (1 << 3) /* Local interrupt 2 enable */
53#define PLX_LINT2_POL (1 << 4) /* Local interrupt 2 polarity */
54#define PLX_PCI_INT_EN (1 << 6) /* PCI Interrupt Enable */
55#define PLX_PCI_RESET (1 << 30) /* PCI Adapter Software Reset */
56
57/* PLX9056 registers */
58#define PLX9056_INTCSR 0x68 /* Interrupt Control/Status */
59#define PLX9056_CNTRL 0x6c /* Control / Software Reset */
60
61#define PLX9056_LINTI (1 << 11)
62#define PLX9056_PCI_INT_EN (1 << 8)
63#define PLX9056_PCI_RCR (1 << 29) /* Read Configuration Registers */
64
65/*
66 * The board configuration is probably following:
67 * RX1 is connected to ground.
68 * TX1 is not connected.
69 * CLKO is not connected.
70 * Setting the OCR register to 0xDA is a good idea.
71 * This means normal output mode, push-pull and the correct polarity.
72 */
73#define PLX_PCI_OCR (OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
74
75/* OCR setting for ASEM Dual CAN raw */
76#define ASEM_PCI_OCR 0xfe
77
78/*
79 * In the CDR register, you should set CBP to 1.
80 * You will probably also want to set the clock divider value to 7
81 * (meaning direct oscillator output) because the second SJA1000 chip
82 * is driven by the first one CLKOUT output.
83 */
84#define PLX_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
85
86/* SJA1000 Control Register in the BasicCAN Mode */
87#define REG_CR 0x00
88
89/* States of some SJA1000 registers after hardware reset in the BasicCAN mode*/
90#define REG_CR_BASICCAN_INITIAL 0x21
91#define REG_CR_BASICCAN_INITIAL_MASK 0xa1
92#define REG_SR_BASICCAN_INITIAL 0x0c
93#define REG_IR_BASICCAN_INITIAL 0xe0
94
95/* States of some SJA1000 registers after hardware reset in the PeliCAN mode*/
96#define REG_MOD_PELICAN_INITIAL 0x01
97#define REG_SR_PELICAN_INITIAL 0x3c
98#define REG_IR_PELICAN_INITIAL 0x00
99
100#define ADLINK_PCI_VENDOR_ID 0x144A
101#define ADLINK_PCI_DEVICE_ID 0x7841
102
103#define ESD_PCI_SUB_SYS_ID_PCI200 0x0004
104#define ESD_PCI_SUB_SYS_ID_PCI266 0x0009
105#define ESD_PCI_SUB_SYS_ID_PMC266 0x000e
106#define ESD_PCI_SUB_SYS_ID_CPCI200 0x010b
107#define ESD_PCI_SUB_SYS_ID_PCIE2000 0x0200
108#define ESD_PCI_SUB_SYS_ID_PCI104200 0x0501
109
110#define CAN200PCI_DEVICE_ID 0x9030
111#define CAN200PCI_VENDOR_ID 0x10b5
112#define CAN200PCI_SUB_DEVICE_ID 0x0301
113#define CAN200PCI_SUB_VENDOR_ID 0xe1c5
114
115#define IXXAT_PCI_VENDOR_ID 0x10b5
116#define IXXAT_PCI_DEVICE_ID 0x9050
117#define IXXAT_PCI_SUB_SYS_ID 0x2540
118
119#define MARATHON_PCI_DEVICE_ID 0x2715
120#define MARATHON_PCIE_DEVICE_ID 0x3432
121
122#define TEWS_PCI_VENDOR_ID 0x1498
123#define TEWS_PCI_DEVICE_ID_TMPC810 0x032A
124
125#define CTI_PCI_VENDOR_ID 0x12c4
126#define CTI_PCI_DEVICE_ID_CRG001 0x0900
127
128#define MOXA_PCI_VENDOR_ID 0x1393
129#define MOXA_PCI_DEVICE_ID 0x0100
130
131#define ASEM_RAW_CAN_VENDOR_ID 0x10b5
132#define ASEM_RAW_CAN_DEVICE_ID 0x9030
133#define ASEM_RAW_CAN_SUB_VENDOR_ID 0x3000
134#define ASEM_RAW_CAN_SUB_DEVICE_ID 0x1001
135#define ASEM_RAW_CAN_SUB_DEVICE_ID_BIS 0x1002
136#define ASEM_RAW_CAN_RST_REGISTER 0x54
137#define ASEM_RAW_CAN_RST_MASK_CAN1 0x20
138#define ASEM_RAW_CAN_RST_MASK_CAN2 0x04
139
140static void plx_pci_reset_common(struct pci_dev *pdev);
141static void plx9056_pci_reset_common(struct pci_dev *pdev);
142static void plx_pci_reset_marathon_pci(struct pci_dev *pdev);
143static void plx_pci_reset_marathon_pcie(struct pci_dev *pdev);
144static void plx_pci_reset_asem_dual_can_raw(struct pci_dev *pdev);
145
146struct plx_pci_channel_map {
147 u32 bar;
148 u32 offset;
149 u32 size; /* 0x00 - auto, e.g. length of entire bar */
150};
151
152struct plx_pci_card_info {
153 const char *name;
154 int channel_count;
155 u32 can_clock;
156 u8 ocr; /* output control register */
157 u8 cdr; /* clock divider register */
158
159 /* Parameters for mapping local configuration space */
160 struct plx_pci_channel_map conf_map;
161
162 /* Parameters for mapping the SJA1000 chips */
163 struct plx_pci_channel_map chan_map_tbl[PLX_PCI_MAX_CHAN];
164
165 /* Pointer to device-dependent reset function */
166 void (*reset_func)(struct pci_dev *pdev);
167};
168
169static struct plx_pci_card_info plx_pci_card_info_adlink = {
170 "Adlink PCI-7841/cPCI-7841", 2,
171 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
172 {1, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x80, 0x80} },
173 &plx_pci_reset_common
174 /* based on PLX9052 */
175};
176
177static struct plx_pci_card_info plx_pci_card_info_adlink_se = {
178 "Adlink PCI-7841/cPCI-7841 SE", 2,
179 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
180 {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x80, 0x80} },
181 &plx_pci_reset_common
182 /* based on PLX9052 */
183};
184
185static struct plx_pci_card_info plx_pci_card_info_esd200 = {
186 "esd CAN-PCI/CPCI/PCI104/200", 2,
187 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
188 {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
189 &plx_pci_reset_common
190 /* based on PLX9030/9050 */
191};
192
193static struct plx_pci_card_info plx_pci_card_info_esd266 = {
194 "esd CAN-PCI/PMC/266", 2,
195 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
196 {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
197 &plx9056_pci_reset_common
198 /* based on PLX9056 */
199};
200
201static struct plx_pci_card_info plx_pci_card_info_esd2000 = {
202 "esd CAN-PCIe/2000", 2,
203 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
204 {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x100, 0x80} },
205 &plx9056_pci_reset_common
206 /* based on PEX8311 */
207};
208
209static struct plx_pci_card_info plx_pci_card_info_ixxat = {
210 "IXXAT PC-I 04/PCI", 2,
211 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
212 {0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x200, 0x80} },
213 &plx_pci_reset_common
214 /* based on PLX9050 */
215};
216
217static struct plx_pci_card_info plx_pci_card_info_marathon_pci = {
218 "Marathon CAN-bus-PCI", 2,
219 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
220 {0, 0x00, 0x00}, { {2, 0x00, 0x00}, {4, 0x00, 0x00} },
221 &plx_pci_reset_marathon_pci
222 /* based on PLX9052 */
223};
224
225static struct plx_pci_card_info plx_pci_card_info_marathon_pcie = {
226 "Marathon CAN-bus-PCIe", 2,
227 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
228 {0, 0x00, 0x00}, { {2, 0x00, 0x00}, {3, 0x80, 0x00} },
229 &plx_pci_reset_marathon_pcie
230 /* based on PEX8311 */
231};
232
233static struct plx_pci_card_info plx_pci_card_info_tews = {
234 "TEWS TECHNOLOGIES TPMC810", 2,
235 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
236 {0, 0x00, 0x00}, { {2, 0x000, 0x80}, {2, 0x100, 0x80} },
237 &plx_pci_reset_common
238 /* based on PLX9030 */
239};
240
241static struct plx_pci_card_info plx_pci_card_info_cti = {
242 "Connect Tech Inc. CANpro/104-Plus Opto (CRG001)", 2,
243 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
244 {0, 0x00, 0x00}, { {2, 0x000, 0x80}, {2, 0x100, 0x80} },
245 &plx_pci_reset_common
246 /* based on PLX9030 */
247};
248
249static struct plx_pci_card_info plx_pci_card_info_elcus = {
250 "Eclus CAN-200-PCI", 2,
251 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
252 {1, 0x00, 0x00}, { {2, 0x00, 0x80}, {3, 0x00, 0x80} },
253 &plx_pci_reset_common
254 /* based on PLX9030 */
255};
256
257static struct plx_pci_card_info plx_pci_card_info_moxa = {
258 "MOXA", 2,
259 PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
260 {0, 0x00, 0x00}, { {0, 0x00, 0x80}, {1, 0x00, 0x80} },
261 &plx_pci_reset_common
262 /* based on PLX9052 */
263};
264
265static struct plx_pci_card_info plx_pci_card_info_asem_dual_can = {
266 "ASEM Dual CAN raw PCI", 2,
267 PLX_PCI_CAN_CLOCK, ASEM_PCI_OCR, PLX_PCI_CDR,
268 {0, 0x00, 0x00}, { {2, 0x00, 0x00}, {4, 0x00, 0x00} },
269 &plx_pci_reset_asem_dual_can_raw
270 /* based on PLX9030 */
271};
272
273static const struct pci_device_id plx_pci_tbl[] = {
274 {
275 /* Adlink PCI-7841/cPCI-7841 */
276 ADLINK_PCI_VENDOR_ID, ADLINK_PCI_DEVICE_ID,
277 PCI_ANY_ID, PCI_ANY_ID,
278 PCI_CLASS_NETWORK_OTHER << 8, ~0,
279 (kernel_ulong_t)&plx_pci_card_info_adlink
280 },
281 {
282 /* Adlink PCI-7841/cPCI-7841 SE */
283 ADLINK_PCI_VENDOR_ID, ADLINK_PCI_DEVICE_ID,
284 PCI_ANY_ID, PCI_ANY_ID,
285 PCI_CLASS_COMMUNICATION_OTHER << 8, ~0,
286 (kernel_ulong_t)&plx_pci_card_info_adlink_se
287 },
288 {
289 /* esd CAN-PCI/200 */
290 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
291 PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI200,
292 0, 0,
293 (kernel_ulong_t)&plx_pci_card_info_esd200
294 },
295 {
296 /* esd CAN-CPCI/200 */
297 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
298 PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_CPCI200,
299 0, 0,
300 (kernel_ulong_t)&plx_pci_card_info_esd200
301 },
302 {
303 /* esd CAN-PCI104/200 */
304 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
305 PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI104200,
306 0, 0,
307 (kernel_ulong_t)&plx_pci_card_info_esd200
308 },
309 {
310 /* esd CAN-PCI/266 */
311 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
312 PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCI266,
313 0, 0,
314 (kernel_ulong_t)&plx_pci_card_info_esd266
315 },
316 {
317 /* esd CAN-PMC/266 */
318 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
319 PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PMC266,
320 0, 0,
321 (kernel_ulong_t)&plx_pci_card_info_esd266
322 },
323 {
324 /* esd CAN-PCIE/2000 */
325 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9056,
326 PCI_VENDOR_ID_ESDGMBH, ESD_PCI_SUB_SYS_ID_PCIE2000,
327 0, 0,
328 (kernel_ulong_t)&plx_pci_card_info_esd2000
329 },
330 {
331 /* IXXAT PC-I 04/PCI card */
332 IXXAT_PCI_VENDOR_ID, IXXAT_PCI_DEVICE_ID,
333 PCI_ANY_ID, IXXAT_PCI_SUB_SYS_ID,
334 0, 0,
335 (kernel_ulong_t)&plx_pci_card_info_ixxat
336 },
337 {
338 /* Marathon CAN-bus-PCI card */
339 PCI_VENDOR_ID_PLX, MARATHON_PCI_DEVICE_ID,
340 PCI_ANY_ID, PCI_ANY_ID,
341 0, 0,
342 (kernel_ulong_t)&plx_pci_card_info_marathon_pci
343 },
344 {
345 /* Marathon CAN-bus-PCIe card */
346 PCI_VENDOR_ID_PLX, MARATHON_PCIE_DEVICE_ID,
347 PCI_ANY_ID, PCI_ANY_ID,
348 0, 0,
349 (kernel_ulong_t)&plx_pci_card_info_marathon_pcie
350 },
351 {
352 /* TEWS TECHNOLOGIES TPMC810 card */
353 TEWS_PCI_VENDOR_ID, TEWS_PCI_DEVICE_ID_TMPC810,
354 PCI_ANY_ID, PCI_ANY_ID,
355 0, 0,
356 (kernel_ulong_t)&plx_pci_card_info_tews
357 },
358 {
359 /* Connect Tech Inc. CANpro/104-Plus Opto (CRG001) card */
360 PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030,
361 CTI_PCI_VENDOR_ID, CTI_PCI_DEVICE_ID_CRG001,
362 0, 0,
363 (kernel_ulong_t)&plx_pci_card_info_cti
364 },
365 {
366 /* Elcus CAN-200-PCI */
367 CAN200PCI_VENDOR_ID, CAN200PCI_DEVICE_ID,
368 CAN200PCI_SUB_VENDOR_ID, CAN200PCI_SUB_DEVICE_ID,
369 0, 0,
370 (kernel_ulong_t)&plx_pci_card_info_elcus
371 },
372 {
373 /* moxa */
374 MOXA_PCI_VENDOR_ID, MOXA_PCI_DEVICE_ID,
375 PCI_ANY_ID, PCI_ANY_ID,
376 0, 0,
377 (kernel_ulong_t)&plx_pci_card_info_moxa
378 },
379 {
380 /* ASEM Dual CAN raw */
381 ASEM_RAW_CAN_VENDOR_ID, ASEM_RAW_CAN_DEVICE_ID,
382 ASEM_RAW_CAN_SUB_VENDOR_ID, ASEM_RAW_CAN_SUB_DEVICE_ID,
383 0, 0,
384 (kernel_ulong_t)&plx_pci_card_info_asem_dual_can
385 },
386 {
387 /* ASEM Dual CAN raw -new model */
388 ASEM_RAW_CAN_VENDOR_ID, ASEM_RAW_CAN_DEVICE_ID,
389 ASEM_RAW_CAN_SUB_VENDOR_ID, ASEM_RAW_CAN_SUB_DEVICE_ID_BIS,
390 0, 0,
391 (kernel_ulong_t)&plx_pci_card_info_asem_dual_can
392 },
393 { 0,}
394};
395MODULE_DEVICE_TABLE(pci, plx_pci_tbl);
396
397static u8 plx_pci_read_reg(const struct sja1000_priv *priv, int port)
398{
399 return ioread8(priv->reg_base + port);
400}
401
402static void plx_pci_write_reg(const struct sja1000_priv *priv, int port, u8 val)
403{
404 iowrite8(val, priv->reg_base + port);
405}
406
407/*
408 * Check if a CAN controller is present at the specified location
409 * by trying to switch 'em from the Basic mode into the PeliCAN mode.
410 * Also check states of some registers in reset mode.
411 */
412static inline int plx_pci_check_sja1000(const struct sja1000_priv *priv)
413{
414 int flag = 0;
415
416 /*
417 * Check registers after hardware reset (the Basic mode)
418 * See states on p. 10 of the Datasheet.
419 */
420 if ((priv->read_reg(priv, REG_CR) & REG_CR_BASICCAN_INITIAL_MASK) ==
421 REG_CR_BASICCAN_INITIAL &&
422 (priv->read_reg(priv, SJA1000_SR) == REG_SR_BASICCAN_INITIAL) &&
423 (priv->read_reg(priv, SJA1000_IR) == REG_IR_BASICCAN_INITIAL))
424 flag = 1;
425
426 /* Bring the SJA1000 into the PeliCAN mode*/
427 priv->write_reg(priv, SJA1000_CDR, CDR_PELICAN);
428
429 /*
430 * Check registers after reset in the PeliCAN mode.
431 * See states on p. 23 of the Datasheet.
432 */
433 if (priv->read_reg(priv, SJA1000_MOD) == REG_MOD_PELICAN_INITIAL &&
434 priv->read_reg(priv, SJA1000_SR) == REG_SR_PELICAN_INITIAL &&
435 priv->read_reg(priv, SJA1000_IR) == REG_IR_PELICAN_INITIAL)
436 return flag;
437
438 return 0;
439}
440
441/*
442 * PLX9030/50/52 software reset
443 * Also LRESET# asserts and brings to reset device on the Local Bus (if wired).
444 * For most cards it's enough for reset the SJA1000 chips.
445 */
446static void plx_pci_reset_common(struct pci_dev *pdev)
447{
448 struct plx_pci_card *card = pci_get_drvdata(pdev);
449 u32 cntrl;
450
451 cntrl = ioread32(card->conf_addr + PLX_CNTRL);
452 cntrl |= PLX_PCI_RESET;
453 iowrite32(cntrl, card->conf_addr + PLX_CNTRL);
454 udelay(100);
455 cntrl ^= PLX_PCI_RESET;
456 iowrite32(cntrl, card->conf_addr + PLX_CNTRL);
457};
458
459/*
460 * PLX9056 software reset
461 * Assert LRESET# and reset device(s) on the Local Bus (if wired).
462 */
463static void plx9056_pci_reset_common(struct pci_dev *pdev)
464{
465 struct plx_pci_card *card = pci_get_drvdata(pdev);
466 u32 cntrl;
467
468 /* issue a local bus reset */
469 cntrl = ioread32(card->conf_addr + PLX9056_CNTRL);
470 cntrl |= PLX_PCI_RESET;
471 iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
472 udelay(100);
473 cntrl ^= PLX_PCI_RESET;
474 iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
475
476 /* reload local configuration from EEPROM */
477 cntrl |= PLX9056_PCI_RCR;
478 iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
479
480 /*
481 * There is no safe way to poll for the end
482 * of reconfiguration process. Waiting for 10ms
483 * is safe.
484 */
485 mdelay(10);
486
487 cntrl ^= PLX9056_PCI_RCR;
488 iowrite32(cntrl, card->conf_addr + PLX9056_CNTRL);
489};
490
491/* Special reset function for Marathon CAN-bus-PCI card */
492static void plx_pci_reset_marathon_pci(struct pci_dev *pdev)
493{
494 void __iomem *reset_addr;
495 int i;
496 static const int reset_bar[2] = {3, 5};
497
498 plx_pci_reset_common(pdev);
499
500 for (i = 0; i < 2; i++) {
501 reset_addr = pci_iomap(pdev, reset_bar[i], 0);
502 if (!reset_addr) {
503 dev_err(&pdev->dev, "Failed to remap reset "
504 "space %d (BAR%d)\n", i, reset_bar[i]);
505 } else {
506 /* reset the SJA1000 chip */
507 iowrite8(0x1, reset_addr);
508 udelay(100);
509 pci_iounmap(pdev, reset_addr);
510 }
511 }
512}
513
514/* Special reset function for Marathon CAN-bus-PCIe card */
515static void plx_pci_reset_marathon_pcie(struct pci_dev *pdev)
516{
517 void __iomem *addr;
518 void __iomem *reset_addr;
519 int i;
520
521 plx9056_pci_reset_common(pdev);
522
523 for (i = 0; i < 2; i++) {
524 struct plx_pci_channel_map *chan_map =
525 &plx_pci_card_info_marathon_pcie.chan_map_tbl[i];
526 addr = pci_iomap(pdev, chan_map->bar, chan_map->size);
527 if (!addr) {
528 dev_err(&pdev->dev, "Failed to remap reset "
529 "space %d (BAR%d)\n", i, chan_map->bar);
530 } else {
531 /* reset the SJA1000 chip */
532 #define MARATHON_PCIE_RESET_OFFSET 32
533 reset_addr = addr + chan_map->offset +
534 MARATHON_PCIE_RESET_OFFSET;
535 iowrite8(0x1, reset_addr);
536 udelay(100);
537 pci_iounmap(pdev, addr);
538 }
539 }
540}
541
542/* Special reset function for ASEM Dual CAN raw card */
543static void plx_pci_reset_asem_dual_can_raw(struct pci_dev *pdev)
544{
545 void __iomem *bar0_addr;
546 u8 tmpval;
547
548 plx_pci_reset_common(pdev);
549
550 bar0_addr = pci_iomap(pdev, 0, 0);
551 if (!bar0_addr) {
552 dev_err(&pdev->dev, "Failed to remap reset space 0 (BAR0)\n");
553 return;
554 }
555
556 /* reset the two SJA1000 chips */
557 tmpval = ioread8(bar0_addr + ASEM_RAW_CAN_RST_REGISTER);
558 tmpval &= ~(ASEM_RAW_CAN_RST_MASK_CAN1 | ASEM_RAW_CAN_RST_MASK_CAN2);
559 iowrite8(tmpval, bar0_addr + ASEM_RAW_CAN_RST_REGISTER);
560 usleep_range(300, 400);
561 tmpval |= ASEM_RAW_CAN_RST_MASK_CAN1 | ASEM_RAW_CAN_RST_MASK_CAN2;
562 iowrite8(tmpval, bar0_addr + ASEM_RAW_CAN_RST_REGISTER);
563 usleep_range(300, 400);
564 pci_iounmap(pdev, bar0_addr);
565}
566
567static void plx_pci_del_card(struct pci_dev *pdev)
568{
569 struct plx_pci_card *card = pci_get_drvdata(pdev);
570 struct net_device *dev;
571 struct sja1000_priv *priv;
572 int i = 0;
573
574 for (i = 0; i < PLX_PCI_MAX_CHAN; i++) {
575 dev = card->net_dev[i];
576 if (!dev)
577 continue;
578
579 dev_info(&pdev->dev, "Removing %s\n", dev->name);
580 unregister_sja1000dev(dev);
581 priv = netdev_priv(dev);
582 if (priv->reg_base)
583 pci_iounmap(pdev, priv->reg_base);
584 free_sja1000dev(dev);
585 }
586
587 card->reset_func(pdev);
588
589 /*
590 * Disable interrupts from PCI-card and disable local
591 * interrupts
592 */
593 if (pdev->device != PCI_DEVICE_ID_PLX_9056 &&
594 pdev->device != MARATHON_PCIE_DEVICE_ID)
595 iowrite32(0x0, card->conf_addr + PLX_INTCSR);
596 else
597 iowrite32(0x0, card->conf_addr + PLX9056_INTCSR);
598
599 if (card->conf_addr)
600 pci_iounmap(pdev, card->conf_addr);
601
602 kfree(card);
603
604 pci_disable_device(pdev);
605}
606
607/*
608 * Probe PLX90xx based device for the SJA1000 chips and register each
609 * available CAN channel to SJA1000 Socket-CAN subsystem.
610 */
611static int plx_pci_add_card(struct pci_dev *pdev,
612 const struct pci_device_id *ent)
613{
614 struct sja1000_priv *priv;
615 struct net_device *dev;
616 struct plx_pci_card *card;
617 struct plx_pci_card_info *ci;
618 int err, i;
619 u32 val;
620 void __iomem *addr;
621
622 ci = (struct plx_pci_card_info *)ent->driver_data;
623
624 if (pci_enable_device(pdev) < 0) {
625 dev_err(&pdev->dev, "Failed to enable PCI device\n");
626 return -ENODEV;
627 }
628
629 dev_info(&pdev->dev, "Detected \"%s\" card at slot #%i\n",
630 ci->name, PCI_SLOT(pdev->devfn));
631
632 /* Allocate card structures to hold addresses, ... */
633 card = kzalloc(sizeof(*card), GFP_KERNEL);
634 if (!card) {
635 pci_disable_device(pdev);
636 return -ENOMEM;
637 }
638
639 pci_set_drvdata(pdev, card);
640
641 card->channels = 0;
642
643 /* Remap PLX90xx configuration space */
644 addr = pci_iomap(pdev, ci->conf_map.bar, ci->conf_map.size);
645 if (!addr) {
646 err = -ENOMEM;
647 dev_err(&pdev->dev, "Failed to remap configuration space "
648 "(BAR%d)\n", ci->conf_map.bar);
649 goto failure_cleanup;
650 }
651 card->conf_addr = addr + ci->conf_map.offset;
652
653 ci->reset_func(pdev);
654 card->reset_func = ci->reset_func;
655
656 /* Detect available channels */
657 for (i = 0; i < ci->channel_count; i++) {
658 struct plx_pci_channel_map *cm = &ci->chan_map_tbl[i];
659
660 dev = alloc_sja1000dev(0);
661 if (!dev) {
662 err = -ENOMEM;
663 goto failure_cleanup;
664 }
665
666 card->net_dev[i] = dev;
667 priv = netdev_priv(dev);
668 priv->priv = card;
669 priv->irq_flags = IRQF_SHARED;
670
671 dev->irq = pdev->irq;
672
673 /*
674 * Remap IO space of the SJA1000 chips
675 * This is device-dependent mapping
676 */
677 addr = pci_iomap(pdev, cm->bar, cm->size);
678 if (!addr) {
679 err = -ENOMEM;
680 dev_err(&pdev->dev, "Failed to remap BAR%d\n", cm->bar);
681 goto failure_cleanup;
682 }
683
684 priv->reg_base = addr + cm->offset;
685 priv->read_reg = plx_pci_read_reg;
686 priv->write_reg = plx_pci_write_reg;
687
688 /* Check if channel is present */
689 if (plx_pci_check_sja1000(priv)) {
690 priv->can.clock.freq = ci->can_clock;
691 priv->ocr = ci->ocr;
692 priv->cdr = ci->cdr;
693
694 SET_NETDEV_DEV(dev, &pdev->dev);
695 dev->dev_id = i;
696
697 /* Register SJA1000 device */
698 err = register_sja1000dev(dev);
699 if (err) {
700 dev_err(&pdev->dev, "Registering device failed "
701 "(err=%d)\n", err);
702 goto failure_cleanup;
703 }
704
705 card->channels++;
706
707 dev_info(&pdev->dev, "Channel #%d at 0x%p, irq %d "
708 "registered as %s\n", i + 1, priv->reg_base,
709 dev->irq, dev->name);
710 } else {
711 dev_err(&pdev->dev, "Channel #%d not detected\n",
712 i + 1);
713 free_sja1000dev(dev);
714 card->net_dev[i] = NULL;
715 }
716 }
717
718 if (!card->channels) {
719 err = -ENODEV;
720 goto failure_cleanup;
721 }
722
723 /*
724 * Enable interrupts from PCI-card (PLX90xx) and enable Local_1,
725 * Local_2 interrupts from the SJA1000 chips
726 */
727 if (pdev->device != PCI_DEVICE_ID_PLX_9056 &&
728 pdev->device != MARATHON_PCIE_DEVICE_ID) {
729 val = ioread32(card->conf_addr + PLX_INTCSR);
730 if (pdev->subsystem_vendor == PCI_VENDOR_ID_ESDGMBH)
731 val |= PLX_LINT1_EN | PLX_PCI_INT_EN;
732 else
733 val |= PLX_LINT1_EN | PLX_LINT2_EN | PLX_PCI_INT_EN;
734 iowrite32(val, card->conf_addr + PLX_INTCSR);
735 } else {
736 iowrite32(PLX9056_LINTI | PLX9056_PCI_INT_EN,
737 card->conf_addr + PLX9056_INTCSR);
738 }
739 return 0;
740
741failure_cleanup:
742 dev_err(&pdev->dev, "Error: %d. Cleaning Up.\n", err);
743
744 plx_pci_del_card(pdev);
745
746 return err;
747}
748
749static struct pci_driver plx_pci_driver = {
750 .name = DRV_NAME,
751 .id_table = plx_pci_tbl,
752 .probe = plx_pci_add_card,
753 .remove = plx_pci_del_card,
754};
755
756module_pci_driver(plx_pci_driver);