Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * RSB (Reduced Serial Bus) driver.
4 *
5 * Author: Chen-Yu Tsai <wens@csie.org>
6 *
7 * The RSB controller looks like an SMBus controller which only supports
8 * byte and word data transfers. But, it differs from standard SMBus
9 * protocol on several aspects:
10 * - it uses addresses set at runtime to address slaves. Runtime addresses
11 * are sent to slaves using their 12bit hardware addresses. Up to 15
12 * runtime addresses are available.
13 * - it adds a parity bit every 8bits of data and address for read and
14 * write accesses; this replaces the ack bit
15 * - only one read access is required to read a byte (instead of a write
16 * followed by a read access in standard SMBus protocol)
17 * - there's no Ack bit after each read access
18 *
19 * This means this bus cannot be used to interface with standard SMBus
20 * devices. Devices known to support this interface include the AXP223,
21 * AXP809, and AXP806 PMICs, and the AC100 audio codec, all from X-Powers.
22 *
23 * A description of the operation and wire protocol can be found in the
24 * RSB section of Allwinner's A80 user manual, which can be found at
25 *
26 * https://github.com/allwinner-zh/documents/tree/master/A80
27 *
28 * This document is officially released by Allwinner.
29 *
30 * This driver is based on i2c-sun6i-p2wi.c, the P2WI bus driver.
31 */
32
33#include <linux/clk.h>
34#include <linux/clk/clk-conf.h>
35#include <linux/device.h>
36#include <linux/interrupt.h>
37#include <linux/io.h>
38#include <linux/iopoll.h>
39#include <linux/module.h>
40#include <linux/of.h>
41#include <linux/of_irq.h>
42#include <linux/of_device.h>
43#include <linux/platform_device.h>
44#include <linux/pm.h>
45#include <linux/pm_runtime.h>
46#include <linux/regmap.h>
47#include <linux/reset.h>
48#include <linux/slab.h>
49#include <linux/sunxi-rsb.h>
50#include <linux/types.h>
51
52/* RSB registers */
53#define RSB_CTRL 0x0 /* Global control */
54#define RSB_CCR 0x4 /* Clock control */
55#define RSB_INTE 0x8 /* Interrupt controls */
56#define RSB_INTS 0xc /* Interrupt status */
57#define RSB_ADDR 0x10 /* Address to send with read/write command */
58#define RSB_DATA 0x1c /* Data to read/write */
59#define RSB_LCR 0x24 /* Line control */
60#define RSB_DMCR 0x28 /* Device mode (init) control */
61#define RSB_CMD 0x2c /* RSB Command */
62#define RSB_DAR 0x30 /* Device address / runtime address */
63
64/* CTRL fields */
65#define RSB_CTRL_START_TRANS BIT(7)
66#define RSB_CTRL_ABORT_TRANS BIT(6)
67#define RSB_CTRL_GLOBAL_INT_ENB BIT(1)
68#define RSB_CTRL_SOFT_RST BIT(0)
69
70/* CLK CTRL fields */
71#define RSB_CCR_SDA_OUT_DELAY(v) (((v) & 0x7) << 8)
72#define RSB_CCR_MAX_CLK_DIV 0xff
73#define RSB_CCR_CLK_DIV(v) ((v) & RSB_CCR_MAX_CLK_DIV)
74
75/* STATUS fields */
76#define RSB_INTS_TRANS_ERR_ACK BIT(16)
77#define RSB_INTS_TRANS_ERR_DATA_BIT(v) (((v) >> 8) & 0xf)
78#define RSB_INTS_TRANS_ERR_DATA GENMASK(11, 8)
79#define RSB_INTS_LOAD_BSY BIT(2)
80#define RSB_INTS_TRANS_ERR BIT(1)
81#define RSB_INTS_TRANS_OVER BIT(0)
82
83/* LINE CTRL fields*/
84#define RSB_LCR_SCL_STATE BIT(5)
85#define RSB_LCR_SDA_STATE BIT(4)
86#define RSB_LCR_SCL_CTL BIT(3)
87#define RSB_LCR_SCL_CTL_EN BIT(2)
88#define RSB_LCR_SDA_CTL BIT(1)
89#define RSB_LCR_SDA_CTL_EN BIT(0)
90
91/* DEVICE MODE CTRL field values */
92#define RSB_DMCR_DEVICE_START BIT(31)
93#define RSB_DMCR_MODE_DATA (0x7c << 16)
94#define RSB_DMCR_MODE_REG (0x3e << 8)
95#define RSB_DMCR_DEV_ADDR 0x00
96
97/* CMD values */
98#define RSB_CMD_RD8 0x8b
99#define RSB_CMD_RD16 0x9c
100#define RSB_CMD_RD32 0xa6
101#define RSB_CMD_WR8 0x4e
102#define RSB_CMD_WR16 0x59
103#define RSB_CMD_WR32 0x63
104#define RSB_CMD_STRA 0xe8
105
106/* DAR fields */
107#define RSB_DAR_RTA(v) (((v) & 0xff) << 16)
108#define RSB_DAR_DA(v) ((v) & 0xffff)
109
110#define RSB_MAX_FREQ 20000000
111
112#define RSB_CTRL_NAME "sunxi-rsb"
113
114struct sunxi_rsb_addr_map {
115 u16 hwaddr;
116 u8 rtaddr;
117};
118
119struct sunxi_rsb {
120 struct device *dev;
121 void __iomem *regs;
122 struct clk *clk;
123 struct reset_control *rstc;
124 struct completion complete;
125 struct mutex lock;
126 unsigned int status;
127 u32 clk_freq;
128};
129
130/* bus / slave device related functions */
131static const struct bus_type sunxi_rsb_bus;
132
133static int sunxi_rsb_device_match(struct device *dev, const struct device_driver *drv)
134{
135 return of_driver_match_device(dev, drv);
136}
137
138static int sunxi_rsb_device_probe(struct device *dev)
139{
140 const struct sunxi_rsb_driver *drv = to_sunxi_rsb_driver(dev->driver);
141 struct sunxi_rsb_device *rdev = to_sunxi_rsb_device(dev);
142 int ret;
143
144 if (!drv->probe)
145 return -ENODEV;
146
147 if (!rdev->irq) {
148 int irq = -ENOENT;
149
150 if (dev->of_node)
151 irq = of_irq_get(dev->of_node, 0);
152
153 if (irq == -EPROBE_DEFER)
154 return irq;
155 if (irq < 0)
156 irq = 0;
157
158 rdev->irq = irq;
159 }
160
161 ret = of_clk_set_defaults(dev->of_node, false);
162 if (ret < 0)
163 return ret;
164
165 return drv->probe(rdev);
166}
167
168static void sunxi_rsb_device_remove(struct device *dev)
169{
170 const struct sunxi_rsb_driver *drv = to_sunxi_rsb_driver(dev->driver);
171
172 drv->remove(to_sunxi_rsb_device(dev));
173}
174
175static int sunxi_rsb_device_modalias(const struct device *dev, struct kobj_uevent_env *env)
176{
177 return of_device_uevent_modalias(dev, env);
178}
179
180static const struct bus_type sunxi_rsb_bus = {
181 .name = RSB_CTRL_NAME,
182 .match = sunxi_rsb_device_match,
183 .probe = sunxi_rsb_device_probe,
184 .remove = sunxi_rsb_device_remove,
185 .uevent = sunxi_rsb_device_modalias,
186};
187
188static void sunxi_rsb_dev_release(struct device *dev)
189{
190 struct sunxi_rsb_device *rdev = to_sunxi_rsb_device(dev);
191
192 kfree(rdev);
193}
194
195/**
196 * sunxi_rsb_device_create() - allocate and add an RSB device
197 * @rsb: RSB controller
198 * @node: RSB slave device node
199 * @hwaddr: RSB slave hardware address
200 * @rtaddr: RSB slave runtime address
201 */
202static struct sunxi_rsb_device *sunxi_rsb_device_create(struct sunxi_rsb *rsb,
203 struct device_node *node, u16 hwaddr, u8 rtaddr)
204{
205 int err;
206 struct sunxi_rsb_device *rdev;
207
208 rdev = kzalloc(sizeof(*rdev), GFP_KERNEL);
209 if (!rdev)
210 return ERR_PTR(-ENOMEM);
211
212 rdev->rsb = rsb;
213 rdev->hwaddr = hwaddr;
214 rdev->rtaddr = rtaddr;
215 rdev->dev.bus = &sunxi_rsb_bus;
216 rdev->dev.parent = rsb->dev;
217 rdev->dev.of_node = node;
218 rdev->dev.release = sunxi_rsb_dev_release;
219
220 dev_set_name(&rdev->dev, "%s-%x", RSB_CTRL_NAME, hwaddr);
221
222 err = device_register(&rdev->dev);
223 if (err < 0) {
224 dev_err(&rdev->dev, "Can't add %s, status %d\n",
225 dev_name(&rdev->dev), err);
226 goto err_device_add;
227 }
228
229 dev_dbg(&rdev->dev, "device %s registered\n", dev_name(&rdev->dev));
230
231 return rdev;
232
233err_device_add:
234 put_device(&rdev->dev);
235
236 return ERR_PTR(err);
237}
238
239/**
240 * sunxi_rsb_device_unregister(): unregister an RSB device
241 * @rdev: rsb_device to be removed
242 */
243static void sunxi_rsb_device_unregister(struct sunxi_rsb_device *rdev)
244{
245 device_unregister(&rdev->dev);
246}
247
248static int sunxi_rsb_remove_devices(struct device *dev, void *data)
249{
250 struct sunxi_rsb_device *rdev = to_sunxi_rsb_device(dev);
251
252 if (dev->bus == &sunxi_rsb_bus)
253 sunxi_rsb_device_unregister(rdev);
254
255 return 0;
256}
257
258/**
259 * sunxi_rsb_driver_register() - Register device driver with RSB core
260 * @rdrv: device driver to be associated with slave-device.
261 *
262 * This API will register the client driver with the RSB framework.
263 * It is typically called from the driver's module-init function.
264 */
265int sunxi_rsb_driver_register(struct sunxi_rsb_driver *rdrv)
266{
267 rdrv->driver.bus = &sunxi_rsb_bus;
268 return driver_register(&rdrv->driver);
269}
270EXPORT_SYMBOL_GPL(sunxi_rsb_driver_register);
271
272/* common code that starts a transfer */
273static int _sunxi_rsb_run_xfer(struct sunxi_rsb *rsb)
274{
275 u32 int_mask, status;
276 bool timeout;
277
278 if (readl(rsb->regs + RSB_CTRL) & RSB_CTRL_START_TRANS) {
279 dev_dbg(rsb->dev, "RSB transfer still in progress\n");
280 return -EBUSY;
281 }
282
283 reinit_completion(&rsb->complete);
284
285 int_mask = RSB_INTS_LOAD_BSY | RSB_INTS_TRANS_ERR | RSB_INTS_TRANS_OVER;
286 writel(int_mask, rsb->regs + RSB_INTE);
287 writel(RSB_CTRL_START_TRANS | RSB_CTRL_GLOBAL_INT_ENB,
288 rsb->regs + RSB_CTRL);
289
290 if (irqs_disabled()) {
291 timeout = readl_poll_timeout_atomic(rsb->regs + RSB_INTS,
292 status, (status & int_mask),
293 10, 100000);
294 writel(status, rsb->regs + RSB_INTS);
295 } else {
296 timeout = !wait_for_completion_io_timeout(&rsb->complete,
297 msecs_to_jiffies(100));
298 status = rsb->status;
299 }
300
301 if (timeout) {
302 dev_dbg(rsb->dev, "RSB timeout\n");
303
304 /* abort the transfer */
305 writel(RSB_CTRL_ABORT_TRANS, rsb->regs + RSB_CTRL);
306
307 /* clear any interrupt flags */
308 writel(readl(rsb->regs + RSB_INTS), rsb->regs + RSB_INTS);
309
310 return -ETIMEDOUT;
311 }
312
313 if (status & RSB_INTS_LOAD_BSY) {
314 dev_dbg(rsb->dev, "RSB busy\n");
315 return -EBUSY;
316 }
317
318 if (status & RSB_INTS_TRANS_ERR) {
319 if (status & RSB_INTS_TRANS_ERR_ACK) {
320 dev_dbg(rsb->dev, "RSB slave nack\n");
321 return -EINVAL;
322 }
323
324 if (status & RSB_INTS_TRANS_ERR_DATA) {
325 dev_dbg(rsb->dev, "RSB transfer data error\n");
326 return -EIO;
327 }
328 }
329
330 return 0;
331}
332
333static int sunxi_rsb_read(struct sunxi_rsb *rsb, u8 rtaddr, u8 addr,
334 u32 *buf, size_t len)
335{
336 u32 cmd;
337 int ret;
338
339 if (!buf)
340 return -EINVAL;
341
342 switch (len) {
343 case 1:
344 cmd = RSB_CMD_RD8;
345 break;
346 case 2:
347 cmd = RSB_CMD_RD16;
348 break;
349 case 4:
350 cmd = RSB_CMD_RD32;
351 break;
352 default:
353 dev_err(rsb->dev, "Invalid access width: %zd\n", len);
354 return -EINVAL;
355 }
356
357 ret = pm_runtime_resume_and_get(rsb->dev);
358 if (ret)
359 return ret;
360
361 mutex_lock(&rsb->lock);
362
363 writel(addr, rsb->regs + RSB_ADDR);
364 writel(RSB_DAR_RTA(rtaddr), rsb->regs + RSB_DAR);
365 writel(cmd, rsb->regs + RSB_CMD);
366
367 ret = _sunxi_rsb_run_xfer(rsb);
368 if (ret)
369 goto unlock;
370
371 *buf = readl(rsb->regs + RSB_DATA) & GENMASK(len * 8 - 1, 0);
372
373unlock:
374 mutex_unlock(&rsb->lock);
375
376 pm_runtime_mark_last_busy(rsb->dev);
377 pm_runtime_put_autosuspend(rsb->dev);
378
379 return ret;
380}
381
382static int sunxi_rsb_write(struct sunxi_rsb *rsb, u8 rtaddr, u8 addr,
383 const u32 *buf, size_t len)
384{
385 u32 cmd;
386 int ret;
387
388 if (!buf)
389 return -EINVAL;
390
391 switch (len) {
392 case 1:
393 cmd = RSB_CMD_WR8;
394 break;
395 case 2:
396 cmd = RSB_CMD_WR16;
397 break;
398 case 4:
399 cmd = RSB_CMD_WR32;
400 break;
401 default:
402 dev_err(rsb->dev, "Invalid access width: %zd\n", len);
403 return -EINVAL;
404 }
405
406 ret = pm_runtime_resume_and_get(rsb->dev);
407 if (ret)
408 return ret;
409
410 mutex_lock(&rsb->lock);
411
412 writel(addr, rsb->regs + RSB_ADDR);
413 writel(RSB_DAR_RTA(rtaddr), rsb->regs + RSB_DAR);
414 writel(*buf, rsb->regs + RSB_DATA);
415 writel(cmd, rsb->regs + RSB_CMD);
416 ret = _sunxi_rsb_run_xfer(rsb);
417
418 mutex_unlock(&rsb->lock);
419
420 pm_runtime_mark_last_busy(rsb->dev);
421 pm_runtime_put_autosuspend(rsb->dev);
422
423 return ret;
424}
425
426/* RSB regmap functions */
427struct sunxi_rsb_ctx {
428 struct sunxi_rsb_device *rdev;
429 int size;
430};
431
432static int regmap_sunxi_rsb_reg_read(void *context, unsigned int reg,
433 unsigned int *val)
434{
435 struct sunxi_rsb_ctx *ctx = context;
436 struct sunxi_rsb_device *rdev = ctx->rdev;
437
438 if (reg > 0xff)
439 return -EINVAL;
440
441 return sunxi_rsb_read(rdev->rsb, rdev->rtaddr, reg, val, ctx->size);
442}
443
444static int regmap_sunxi_rsb_reg_write(void *context, unsigned int reg,
445 unsigned int val)
446{
447 struct sunxi_rsb_ctx *ctx = context;
448 struct sunxi_rsb_device *rdev = ctx->rdev;
449
450 return sunxi_rsb_write(rdev->rsb, rdev->rtaddr, reg, &val, ctx->size);
451}
452
453static void regmap_sunxi_rsb_free_ctx(void *context)
454{
455 struct sunxi_rsb_ctx *ctx = context;
456
457 kfree(ctx);
458}
459
460static const struct regmap_bus regmap_sunxi_rsb = {
461 .reg_write = regmap_sunxi_rsb_reg_write,
462 .reg_read = regmap_sunxi_rsb_reg_read,
463 .free_context = regmap_sunxi_rsb_free_ctx,
464 .reg_format_endian_default = REGMAP_ENDIAN_NATIVE,
465 .val_format_endian_default = REGMAP_ENDIAN_NATIVE,
466};
467
468static struct sunxi_rsb_ctx *regmap_sunxi_rsb_init_ctx(struct sunxi_rsb_device *rdev,
469 const struct regmap_config *config)
470{
471 struct sunxi_rsb_ctx *ctx;
472
473 switch (config->val_bits) {
474 case 8:
475 case 16:
476 case 32:
477 break;
478 default:
479 return ERR_PTR(-EINVAL);
480 }
481
482 ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
483 if (!ctx)
484 return ERR_PTR(-ENOMEM);
485
486 ctx->rdev = rdev;
487 ctx->size = config->val_bits / 8;
488
489 return ctx;
490}
491
492struct regmap *__devm_regmap_init_sunxi_rsb(struct sunxi_rsb_device *rdev,
493 const struct regmap_config *config,
494 struct lock_class_key *lock_key,
495 const char *lock_name)
496{
497 struct sunxi_rsb_ctx *ctx = regmap_sunxi_rsb_init_ctx(rdev, config);
498
499 if (IS_ERR(ctx))
500 return ERR_CAST(ctx);
501
502 return __devm_regmap_init(&rdev->dev, ®map_sunxi_rsb, ctx, config,
503 lock_key, lock_name);
504}
505EXPORT_SYMBOL_GPL(__devm_regmap_init_sunxi_rsb);
506
507/* RSB controller driver functions */
508static irqreturn_t sunxi_rsb_irq(int irq, void *dev_id)
509{
510 struct sunxi_rsb *rsb = dev_id;
511 u32 status;
512
513 status = readl(rsb->regs + RSB_INTS);
514 rsb->status = status;
515
516 /* Clear interrupts */
517 status &= (RSB_INTS_LOAD_BSY | RSB_INTS_TRANS_ERR |
518 RSB_INTS_TRANS_OVER);
519 writel(status, rsb->regs + RSB_INTS);
520
521 complete(&rsb->complete);
522
523 return IRQ_HANDLED;
524}
525
526static int sunxi_rsb_init_device_mode(struct sunxi_rsb *rsb)
527{
528 int ret = 0;
529 u32 reg;
530
531 /* send init sequence */
532 writel(RSB_DMCR_DEVICE_START | RSB_DMCR_MODE_DATA |
533 RSB_DMCR_MODE_REG | RSB_DMCR_DEV_ADDR, rsb->regs + RSB_DMCR);
534
535 readl_poll_timeout(rsb->regs + RSB_DMCR, reg,
536 !(reg & RSB_DMCR_DEVICE_START), 100, 250000);
537 if (reg & RSB_DMCR_DEVICE_START)
538 ret = -ETIMEDOUT;
539
540 /* clear interrupt status bits */
541 writel(readl(rsb->regs + RSB_INTS), rsb->regs + RSB_INTS);
542
543 return ret;
544}
545
546/*
547 * There are 15 valid runtime addresses, though Allwinner typically
548 * skips the first, for unknown reasons, and uses the following three.
549 *
550 * 0x17, 0x2d, 0x3a, 0x4e, 0x59, 0x63, 0x74, 0x8b,
551 * 0x9c, 0xa6, 0xb1, 0xc5, 0xd2, 0xe8, 0xff
552 *
553 * No designs with 2 RSB slave devices sharing identical hardware
554 * addresses on the same bus have been seen in the wild. All designs
555 * use 0x2d for the primary PMIC, 0x3a for the secondary PMIC if
556 * there is one, and 0x45 for peripheral ICs.
557 *
558 * The hardware does not seem to support re-setting runtime addresses.
559 * Attempts to do so result in the slave devices returning a NACK.
560 * Hence we just hardcode the mapping here, like Allwinner does.
561 */
562
563static const struct sunxi_rsb_addr_map sunxi_rsb_addr_maps[] = {
564 { 0x3a3, 0x2d }, /* Primary PMIC: AXP223, AXP809, AXP81X, ... */
565 { 0x745, 0x3a }, /* Secondary PMIC: AXP806, ... */
566 { 0xe89, 0x4e }, /* Peripheral IC: AC100, ... */
567};
568
569static u8 sunxi_rsb_get_rtaddr(u16 hwaddr)
570{
571 int i;
572
573 for (i = 0; i < ARRAY_SIZE(sunxi_rsb_addr_maps); i++)
574 if (hwaddr == sunxi_rsb_addr_maps[i].hwaddr)
575 return sunxi_rsb_addr_maps[i].rtaddr;
576
577 return 0; /* 0 is an invalid runtime address */
578}
579
580static int of_rsb_register_devices(struct sunxi_rsb *rsb)
581{
582 struct device *dev = rsb->dev;
583 struct device_node *child, *np = dev->of_node;
584 u32 hwaddr;
585 u8 rtaddr;
586 int ret;
587
588 if (!np)
589 return -EINVAL;
590
591 /* Runtime addresses for all slaves should be set first */
592 for_each_available_child_of_node(np, child) {
593 dev_dbg(dev, "setting child %pOF runtime address\n",
594 child);
595
596 ret = of_property_read_u32(child, "reg", &hwaddr);
597 if (ret) {
598 dev_err(dev, "%pOF: invalid 'reg' property: %d\n",
599 child, ret);
600 continue;
601 }
602
603 rtaddr = sunxi_rsb_get_rtaddr(hwaddr);
604 if (!rtaddr) {
605 dev_err(dev, "%pOF: unknown hardware device address\n",
606 child);
607 continue;
608 }
609
610 /*
611 * Since no devices have been registered yet, we are the
612 * only ones using the bus, we can skip locking the bus.
613 */
614
615 /* setup command parameters */
616 writel(RSB_CMD_STRA, rsb->regs + RSB_CMD);
617 writel(RSB_DAR_RTA(rtaddr) | RSB_DAR_DA(hwaddr),
618 rsb->regs + RSB_DAR);
619
620 /* send command */
621 ret = _sunxi_rsb_run_xfer(rsb);
622 if (ret)
623 dev_warn(dev, "%pOF: set runtime address failed: %d\n",
624 child, ret);
625 }
626
627 /* Then we start adding devices and probing them */
628 for_each_available_child_of_node(np, child) {
629 struct sunxi_rsb_device *rdev;
630
631 dev_dbg(dev, "adding child %pOF\n", child);
632
633 ret = of_property_read_u32(child, "reg", &hwaddr);
634 if (ret)
635 continue;
636
637 rtaddr = sunxi_rsb_get_rtaddr(hwaddr);
638 if (!rtaddr)
639 continue;
640
641 rdev = sunxi_rsb_device_create(rsb, child, hwaddr, rtaddr);
642 if (IS_ERR(rdev))
643 dev_err(dev, "failed to add child device %pOF: %ld\n",
644 child, PTR_ERR(rdev));
645 }
646
647 return 0;
648}
649
650static int sunxi_rsb_hw_init(struct sunxi_rsb *rsb)
651{
652 struct device *dev = rsb->dev;
653 unsigned long p_clk_freq;
654 u32 clk_delay, reg;
655 int clk_div, ret;
656
657 ret = clk_prepare_enable(rsb->clk);
658 if (ret) {
659 dev_err(dev, "failed to enable clk: %d\n", ret);
660 return ret;
661 }
662
663 ret = reset_control_deassert(rsb->rstc);
664 if (ret) {
665 dev_err(dev, "failed to deassert reset line: %d\n", ret);
666 goto err_clk_disable;
667 }
668
669 /* reset the controller */
670 writel(RSB_CTRL_SOFT_RST, rsb->regs + RSB_CTRL);
671 readl_poll_timeout(rsb->regs + RSB_CTRL, reg,
672 !(reg & RSB_CTRL_SOFT_RST), 1000, 100000);
673
674 /*
675 * Clock frequency and delay calculation code is from
676 * Allwinner U-boot sources.
677 *
678 * From A83 user manual:
679 * bus clock frequency = parent clock frequency / (2 * (divider + 1))
680 */
681 p_clk_freq = clk_get_rate(rsb->clk);
682 clk_div = p_clk_freq / rsb->clk_freq / 2;
683 if (!clk_div)
684 clk_div = 1;
685 else if (clk_div > RSB_CCR_MAX_CLK_DIV + 1)
686 clk_div = RSB_CCR_MAX_CLK_DIV + 1;
687
688 clk_delay = clk_div >> 1;
689 if (!clk_delay)
690 clk_delay = 1;
691
692 dev_info(dev, "RSB running at %lu Hz\n", p_clk_freq / clk_div / 2);
693 writel(RSB_CCR_SDA_OUT_DELAY(clk_delay) | RSB_CCR_CLK_DIV(clk_div - 1),
694 rsb->regs + RSB_CCR);
695
696 return 0;
697
698err_clk_disable:
699 clk_disable_unprepare(rsb->clk);
700
701 return ret;
702}
703
704static void sunxi_rsb_hw_exit(struct sunxi_rsb *rsb)
705{
706 reset_control_assert(rsb->rstc);
707
708 /* Keep the clock and PM reference counts consistent. */
709 if (!pm_runtime_status_suspended(rsb->dev))
710 clk_disable_unprepare(rsb->clk);
711}
712
713static int __maybe_unused sunxi_rsb_runtime_suspend(struct device *dev)
714{
715 struct sunxi_rsb *rsb = dev_get_drvdata(dev);
716
717 clk_disable_unprepare(rsb->clk);
718
719 return 0;
720}
721
722static int __maybe_unused sunxi_rsb_runtime_resume(struct device *dev)
723{
724 struct sunxi_rsb *rsb = dev_get_drvdata(dev);
725
726 return clk_prepare_enable(rsb->clk);
727}
728
729static int __maybe_unused sunxi_rsb_suspend(struct device *dev)
730{
731 struct sunxi_rsb *rsb = dev_get_drvdata(dev);
732
733 sunxi_rsb_hw_exit(rsb);
734
735 return 0;
736}
737
738static int __maybe_unused sunxi_rsb_resume(struct device *dev)
739{
740 struct sunxi_rsb *rsb = dev_get_drvdata(dev);
741
742 return sunxi_rsb_hw_init(rsb);
743}
744
745static int sunxi_rsb_probe(struct platform_device *pdev)
746{
747 struct device *dev = &pdev->dev;
748 struct device_node *np = dev->of_node;
749 struct sunxi_rsb *rsb;
750 u32 clk_freq = 3000000;
751 int irq, ret;
752
753 of_property_read_u32(np, "clock-frequency", &clk_freq);
754 if (clk_freq > RSB_MAX_FREQ)
755 return dev_err_probe(dev, -EINVAL,
756 "clock-frequency (%u Hz) is too high (max = 20MHz)\n",
757 clk_freq);
758
759 rsb = devm_kzalloc(dev, sizeof(*rsb), GFP_KERNEL);
760 if (!rsb)
761 return -ENOMEM;
762
763 rsb->dev = dev;
764 rsb->clk_freq = clk_freq;
765 platform_set_drvdata(pdev, rsb);
766 rsb->regs = devm_platform_ioremap_resource(pdev, 0);
767 if (IS_ERR(rsb->regs))
768 return PTR_ERR(rsb->regs);
769
770 irq = platform_get_irq(pdev, 0);
771 if (irq < 0)
772 return irq;
773
774 rsb->clk = devm_clk_get(dev, NULL);
775 if (IS_ERR(rsb->clk))
776 return dev_err_probe(dev, PTR_ERR(rsb->clk),
777 "failed to retrieve clk\n");
778
779 rsb->rstc = devm_reset_control_get(dev, NULL);
780 if (IS_ERR(rsb->rstc))
781 return dev_err_probe(dev, PTR_ERR(rsb->rstc),
782 "failed to retrieve reset controller\n");
783
784 init_completion(&rsb->complete);
785 mutex_init(&rsb->lock);
786
787 ret = devm_request_irq(dev, irq, sunxi_rsb_irq, 0, RSB_CTRL_NAME, rsb);
788 if (ret)
789 return dev_err_probe(dev, ret,
790 "can't register interrupt handler irq %d\n", irq);
791
792 ret = sunxi_rsb_hw_init(rsb);
793 if (ret)
794 return ret;
795
796 /* initialize all devices on the bus into RSB mode */
797 ret = sunxi_rsb_init_device_mode(rsb);
798 if (ret)
799 dev_warn(dev, "Initialize device mode failed: %d\n", ret);
800
801 pm_suspend_ignore_children(dev, true);
802 pm_runtime_set_active(dev);
803 pm_runtime_set_autosuspend_delay(dev, MSEC_PER_SEC);
804 pm_runtime_use_autosuspend(dev);
805 pm_runtime_enable(dev);
806
807 of_rsb_register_devices(rsb);
808
809 return 0;
810}
811
812static void sunxi_rsb_remove(struct platform_device *pdev)
813{
814 struct sunxi_rsb *rsb = platform_get_drvdata(pdev);
815
816 device_for_each_child(rsb->dev, NULL, sunxi_rsb_remove_devices);
817 pm_runtime_disable(&pdev->dev);
818 sunxi_rsb_hw_exit(rsb);
819}
820
821static const struct dev_pm_ops sunxi_rsb_dev_pm_ops = {
822 SET_RUNTIME_PM_OPS(sunxi_rsb_runtime_suspend,
823 sunxi_rsb_runtime_resume, NULL)
824 SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(sunxi_rsb_suspend, sunxi_rsb_resume)
825};
826
827static const struct of_device_id sunxi_rsb_of_match_table[] = {
828 { .compatible = "allwinner,sun8i-a23-rsb" },
829 {}
830};
831MODULE_DEVICE_TABLE(of, sunxi_rsb_of_match_table);
832
833static struct platform_driver sunxi_rsb_driver = {
834 .probe = sunxi_rsb_probe,
835 .remove = sunxi_rsb_remove,
836 .driver = {
837 .name = RSB_CTRL_NAME,
838 .of_match_table = sunxi_rsb_of_match_table,
839 .pm = &sunxi_rsb_dev_pm_ops,
840 },
841};
842
843static int __init sunxi_rsb_init(void)
844{
845 int ret;
846
847 ret = bus_register(&sunxi_rsb_bus);
848 if (ret) {
849 pr_err("failed to register sunxi sunxi_rsb bus: %d\n", ret);
850 return ret;
851 }
852
853 ret = platform_driver_register(&sunxi_rsb_driver);
854 if (ret) {
855 bus_unregister(&sunxi_rsb_bus);
856 return ret;
857 }
858
859 return 0;
860}
861module_init(sunxi_rsb_init);
862
863static void __exit sunxi_rsb_exit(void)
864{
865 platform_driver_unregister(&sunxi_rsb_driver);
866 bus_unregister(&sunxi_rsb_bus);
867}
868module_exit(sunxi_rsb_exit);
869
870MODULE_AUTHOR("Chen-Yu Tsai <wens@csie.org>");
871MODULE_DESCRIPTION("Allwinner sunXi Reduced Serial Bus controller driver");
872MODULE_LICENSE("GPL v2");
1/*
2 * RSB (Reduced Serial Bus) driver.
3 *
4 * Author: Chen-Yu Tsai <wens@csie.org>
5 *
6 * This file is licensed under the terms of the GNU General Public License
7 * version 2. This program is licensed "as is" without any warranty of any
8 * kind, whether express or implied.
9 *
10 * The RSB controller looks like an SMBus controller which only supports
11 * byte and word data transfers. But, it differs from standard SMBus
12 * protocol on several aspects:
13 * - it uses addresses set at runtime to address slaves. Runtime addresses
14 * are sent to slaves using their 12bit hardware addresses. Up to 15
15 * runtime addresses are available.
16 * - it adds a parity bit every 8bits of data and address for read and
17 * write accesses; this replaces the ack bit
18 * - only one read access is required to read a byte (instead of a write
19 * followed by a read access in standard SMBus protocol)
20 * - there's no Ack bit after each read access
21 *
22 * This means this bus cannot be used to interface with standard SMBus
23 * devices. Devices known to support this interface include the AXP223,
24 * AXP809, and AXP806 PMICs, and the AC100 audio codec, all from X-Powers.
25 *
26 * A description of the operation and wire protocol can be found in the
27 * RSB section of Allwinner's A80 user manual, which can be found at
28 *
29 * https://github.com/allwinner-zh/documents/tree/master/A80
30 *
31 * This document is officially released by Allwinner.
32 *
33 * This driver is based on i2c-sun6i-p2wi.c, the P2WI bus driver.
34 *
35 */
36
37#include <linux/clk.h>
38#include <linux/clk/clk-conf.h>
39#include <linux/device.h>
40#include <linux/interrupt.h>
41#include <linux/io.h>
42#include <linux/iopoll.h>
43#include <linux/module.h>
44#include <linux/of.h>
45#include <linux/of_irq.h>
46#include <linux/of_platform.h>
47#include <linux/platform_device.h>
48#include <linux/regmap.h>
49#include <linux/reset.h>
50#include <linux/slab.h>
51#include <linux/sunxi-rsb.h>
52#include <linux/types.h>
53
54/* RSB registers */
55#define RSB_CTRL 0x0 /* Global control */
56#define RSB_CCR 0x4 /* Clock control */
57#define RSB_INTE 0x8 /* Interrupt controls */
58#define RSB_INTS 0xc /* Interrupt status */
59#define RSB_ADDR 0x10 /* Address to send with read/write command */
60#define RSB_DATA 0x1c /* Data to read/write */
61#define RSB_LCR 0x24 /* Line control */
62#define RSB_DMCR 0x28 /* Device mode (init) control */
63#define RSB_CMD 0x2c /* RSB Command */
64#define RSB_DAR 0x30 /* Device address / runtime address */
65
66/* CTRL fields */
67#define RSB_CTRL_START_TRANS BIT(7)
68#define RSB_CTRL_ABORT_TRANS BIT(6)
69#define RSB_CTRL_GLOBAL_INT_ENB BIT(1)
70#define RSB_CTRL_SOFT_RST BIT(0)
71
72/* CLK CTRL fields */
73#define RSB_CCR_SDA_OUT_DELAY(v) (((v) & 0x7) << 8)
74#define RSB_CCR_MAX_CLK_DIV 0xff
75#define RSB_CCR_CLK_DIV(v) ((v) & RSB_CCR_MAX_CLK_DIV)
76
77/* STATUS fields */
78#define RSB_INTS_TRANS_ERR_ACK BIT(16)
79#define RSB_INTS_TRANS_ERR_DATA_BIT(v) (((v) >> 8) & 0xf)
80#define RSB_INTS_TRANS_ERR_DATA GENMASK(11, 8)
81#define RSB_INTS_LOAD_BSY BIT(2)
82#define RSB_INTS_TRANS_ERR BIT(1)
83#define RSB_INTS_TRANS_OVER BIT(0)
84
85/* LINE CTRL fields*/
86#define RSB_LCR_SCL_STATE BIT(5)
87#define RSB_LCR_SDA_STATE BIT(4)
88#define RSB_LCR_SCL_CTL BIT(3)
89#define RSB_LCR_SCL_CTL_EN BIT(2)
90#define RSB_LCR_SDA_CTL BIT(1)
91#define RSB_LCR_SDA_CTL_EN BIT(0)
92
93/* DEVICE MODE CTRL field values */
94#define RSB_DMCR_DEVICE_START BIT(31)
95#define RSB_DMCR_MODE_DATA (0x7c << 16)
96#define RSB_DMCR_MODE_REG (0x3e << 8)
97#define RSB_DMCR_DEV_ADDR 0x00
98
99/* CMD values */
100#define RSB_CMD_RD8 0x8b
101#define RSB_CMD_RD16 0x9c
102#define RSB_CMD_RD32 0xa6
103#define RSB_CMD_WR8 0x4e
104#define RSB_CMD_WR16 0x59
105#define RSB_CMD_WR32 0x63
106#define RSB_CMD_STRA 0xe8
107
108/* DAR fields */
109#define RSB_DAR_RTA(v) (((v) & 0xff) << 16)
110#define RSB_DAR_DA(v) ((v) & 0xffff)
111
112#define RSB_MAX_FREQ 20000000
113
114#define RSB_CTRL_NAME "sunxi-rsb"
115
116struct sunxi_rsb_addr_map {
117 u16 hwaddr;
118 u8 rtaddr;
119};
120
121struct sunxi_rsb {
122 struct device *dev;
123 void __iomem *regs;
124 struct clk *clk;
125 struct reset_control *rstc;
126 struct completion complete;
127 struct mutex lock;
128 unsigned int status;
129};
130
131/* bus / slave device related functions */
132static struct bus_type sunxi_rsb_bus;
133
134static int sunxi_rsb_device_match(struct device *dev, struct device_driver *drv)
135{
136 return of_driver_match_device(dev, drv);
137}
138
139static int sunxi_rsb_device_probe(struct device *dev)
140{
141 const struct sunxi_rsb_driver *drv = to_sunxi_rsb_driver(dev->driver);
142 struct sunxi_rsb_device *rdev = to_sunxi_rsb_device(dev);
143 int ret;
144
145 if (!drv->probe)
146 return -ENODEV;
147
148 if (!rdev->irq) {
149 int irq = -ENOENT;
150
151 if (dev->of_node)
152 irq = of_irq_get(dev->of_node, 0);
153
154 if (irq == -EPROBE_DEFER)
155 return irq;
156 if (irq < 0)
157 irq = 0;
158
159 rdev->irq = irq;
160 }
161
162 ret = of_clk_set_defaults(dev->of_node, false);
163 if (ret < 0)
164 return ret;
165
166 return drv->probe(rdev);
167}
168
169static int sunxi_rsb_device_remove(struct device *dev)
170{
171 const struct sunxi_rsb_driver *drv = to_sunxi_rsb_driver(dev->driver);
172
173 return drv->remove(to_sunxi_rsb_device(dev));
174}
175
176static struct bus_type sunxi_rsb_bus = {
177 .name = RSB_CTRL_NAME,
178 .match = sunxi_rsb_device_match,
179 .probe = sunxi_rsb_device_probe,
180 .remove = sunxi_rsb_device_remove,
181};
182
183static void sunxi_rsb_dev_release(struct device *dev)
184{
185 struct sunxi_rsb_device *rdev = to_sunxi_rsb_device(dev);
186
187 kfree(rdev);
188}
189
190/**
191 * sunxi_rsb_device_create() - allocate and add an RSB device
192 * @rsb: RSB controller
193 * @node: RSB slave device node
194 * @hwaddr: RSB slave hardware address
195 * @rtaddr: RSB slave runtime address
196 */
197static struct sunxi_rsb_device *sunxi_rsb_device_create(struct sunxi_rsb *rsb,
198 struct device_node *node, u16 hwaddr, u8 rtaddr)
199{
200 int err;
201 struct sunxi_rsb_device *rdev;
202
203 rdev = kzalloc(sizeof(*rdev), GFP_KERNEL);
204 if (!rdev)
205 return ERR_PTR(-ENOMEM);
206
207 rdev->rsb = rsb;
208 rdev->hwaddr = hwaddr;
209 rdev->rtaddr = rtaddr;
210 rdev->dev.bus = &sunxi_rsb_bus;
211 rdev->dev.parent = rsb->dev;
212 rdev->dev.of_node = node;
213 rdev->dev.release = sunxi_rsb_dev_release;
214
215 dev_set_name(&rdev->dev, "%s-%x", RSB_CTRL_NAME, hwaddr);
216
217 err = device_register(&rdev->dev);
218 if (err < 0) {
219 dev_err(&rdev->dev, "Can't add %s, status %d\n",
220 dev_name(&rdev->dev), err);
221 goto err_device_add;
222 }
223
224 dev_dbg(&rdev->dev, "device %s registered\n", dev_name(&rdev->dev));
225
226err_device_add:
227 put_device(&rdev->dev);
228
229 return ERR_PTR(err);
230}
231
232/**
233 * sunxi_rsb_device_unregister(): unregister an RSB device
234 * @rdev: rsb_device to be removed
235 */
236static void sunxi_rsb_device_unregister(struct sunxi_rsb_device *rdev)
237{
238 device_unregister(&rdev->dev);
239}
240
241static int sunxi_rsb_remove_devices(struct device *dev, void *data)
242{
243 struct sunxi_rsb_device *rdev = to_sunxi_rsb_device(dev);
244
245 if (dev->bus == &sunxi_rsb_bus)
246 sunxi_rsb_device_unregister(rdev);
247
248 return 0;
249}
250
251/**
252 * sunxi_rsb_driver_register() - Register device driver with RSB core
253 * @rdrv: device driver to be associated with slave-device.
254 *
255 * This API will register the client driver with the RSB framework.
256 * It is typically called from the driver's module-init function.
257 */
258int sunxi_rsb_driver_register(struct sunxi_rsb_driver *rdrv)
259{
260 rdrv->driver.bus = &sunxi_rsb_bus;
261 return driver_register(&rdrv->driver);
262}
263EXPORT_SYMBOL_GPL(sunxi_rsb_driver_register);
264
265/* common code that starts a transfer */
266static int _sunxi_rsb_run_xfer(struct sunxi_rsb *rsb)
267{
268 if (readl(rsb->regs + RSB_CTRL) & RSB_CTRL_START_TRANS) {
269 dev_dbg(rsb->dev, "RSB transfer still in progress\n");
270 return -EBUSY;
271 }
272
273 reinit_completion(&rsb->complete);
274
275 writel(RSB_INTS_LOAD_BSY | RSB_INTS_TRANS_ERR | RSB_INTS_TRANS_OVER,
276 rsb->regs + RSB_INTE);
277 writel(RSB_CTRL_START_TRANS | RSB_CTRL_GLOBAL_INT_ENB,
278 rsb->regs + RSB_CTRL);
279
280 if (!wait_for_completion_io_timeout(&rsb->complete,
281 msecs_to_jiffies(100))) {
282 dev_dbg(rsb->dev, "RSB timeout\n");
283
284 /* abort the transfer */
285 writel(RSB_CTRL_ABORT_TRANS, rsb->regs + RSB_CTRL);
286
287 /* clear any interrupt flags */
288 writel(readl(rsb->regs + RSB_INTS), rsb->regs + RSB_INTS);
289
290 return -ETIMEDOUT;
291 }
292
293 if (rsb->status & RSB_INTS_LOAD_BSY) {
294 dev_dbg(rsb->dev, "RSB busy\n");
295 return -EBUSY;
296 }
297
298 if (rsb->status & RSB_INTS_TRANS_ERR) {
299 if (rsb->status & RSB_INTS_TRANS_ERR_ACK) {
300 dev_dbg(rsb->dev, "RSB slave nack\n");
301 return -EINVAL;
302 }
303
304 if (rsb->status & RSB_INTS_TRANS_ERR_DATA) {
305 dev_dbg(rsb->dev, "RSB transfer data error\n");
306 return -EIO;
307 }
308 }
309
310 return 0;
311}
312
313static int sunxi_rsb_read(struct sunxi_rsb *rsb, u8 rtaddr, u8 addr,
314 u32 *buf, size_t len)
315{
316 u32 cmd;
317 int ret;
318
319 if (!buf)
320 return -EINVAL;
321
322 switch (len) {
323 case 1:
324 cmd = RSB_CMD_RD8;
325 break;
326 case 2:
327 cmd = RSB_CMD_RD16;
328 break;
329 case 4:
330 cmd = RSB_CMD_RD32;
331 break;
332 default:
333 dev_err(rsb->dev, "Invalid access width: %zd\n", len);
334 return -EINVAL;
335 }
336
337 mutex_lock(&rsb->lock);
338
339 writel(addr, rsb->regs + RSB_ADDR);
340 writel(RSB_DAR_RTA(rtaddr), rsb->regs + RSB_DAR);
341 writel(cmd, rsb->regs + RSB_CMD);
342
343 ret = _sunxi_rsb_run_xfer(rsb);
344 if (ret)
345 goto unlock;
346
347 *buf = readl(rsb->regs + RSB_DATA);
348
349unlock:
350 mutex_unlock(&rsb->lock);
351
352 return ret;
353}
354
355static int sunxi_rsb_write(struct sunxi_rsb *rsb, u8 rtaddr, u8 addr,
356 const u32 *buf, size_t len)
357{
358 u32 cmd;
359 int ret;
360
361 if (!buf)
362 return -EINVAL;
363
364 switch (len) {
365 case 1:
366 cmd = RSB_CMD_WR8;
367 break;
368 case 2:
369 cmd = RSB_CMD_WR16;
370 break;
371 case 4:
372 cmd = RSB_CMD_WR32;
373 break;
374 default:
375 dev_err(rsb->dev, "Invalid access width: %zd\n", len);
376 return -EINVAL;
377 }
378
379 mutex_lock(&rsb->lock);
380
381 writel(addr, rsb->regs + RSB_ADDR);
382 writel(RSB_DAR_RTA(rtaddr), rsb->regs + RSB_DAR);
383 writel(*buf, rsb->regs + RSB_DATA);
384 writel(cmd, rsb->regs + RSB_CMD);
385 ret = _sunxi_rsb_run_xfer(rsb);
386
387 mutex_unlock(&rsb->lock);
388
389 return ret;
390}
391
392/* RSB regmap functions */
393struct sunxi_rsb_ctx {
394 struct sunxi_rsb_device *rdev;
395 int size;
396};
397
398static int regmap_sunxi_rsb_reg_read(void *context, unsigned int reg,
399 unsigned int *val)
400{
401 struct sunxi_rsb_ctx *ctx = context;
402 struct sunxi_rsb_device *rdev = ctx->rdev;
403
404 if (reg > 0xff)
405 return -EINVAL;
406
407 return sunxi_rsb_read(rdev->rsb, rdev->rtaddr, reg, val, ctx->size);
408}
409
410static int regmap_sunxi_rsb_reg_write(void *context, unsigned int reg,
411 unsigned int val)
412{
413 struct sunxi_rsb_ctx *ctx = context;
414 struct sunxi_rsb_device *rdev = ctx->rdev;
415
416 return sunxi_rsb_write(rdev->rsb, rdev->rtaddr, reg, &val, ctx->size);
417}
418
419static void regmap_sunxi_rsb_free_ctx(void *context)
420{
421 struct sunxi_rsb_ctx *ctx = context;
422
423 kfree(ctx);
424}
425
426static struct regmap_bus regmap_sunxi_rsb = {
427 .reg_write = regmap_sunxi_rsb_reg_write,
428 .reg_read = regmap_sunxi_rsb_reg_read,
429 .free_context = regmap_sunxi_rsb_free_ctx,
430 .reg_format_endian_default = REGMAP_ENDIAN_NATIVE,
431 .val_format_endian_default = REGMAP_ENDIAN_NATIVE,
432};
433
434static struct sunxi_rsb_ctx *regmap_sunxi_rsb_init_ctx(struct sunxi_rsb_device *rdev,
435 const struct regmap_config *config)
436{
437 struct sunxi_rsb_ctx *ctx;
438
439 switch (config->val_bits) {
440 case 8:
441 case 16:
442 case 32:
443 break;
444 default:
445 return ERR_PTR(-EINVAL);
446 }
447
448 ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
449 if (!ctx)
450 return ERR_PTR(-ENOMEM);
451
452 ctx->rdev = rdev;
453 ctx->size = config->val_bits / 8;
454
455 return ctx;
456}
457
458struct regmap *__devm_regmap_init_sunxi_rsb(struct sunxi_rsb_device *rdev,
459 const struct regmap_config *config,
460 struct lock_class_key *lock_key,
461 const char *lock_name)
462{
463 struct sunxi_rsb_ctx *ctx = regmap_sunxi_rsb_init_ctx(rdev, config);
464
465 if (IS_ERR(ctx))
466 return ERR_CAST(ctx);
467
468 return __devm_regmap_init(&rdev->dev, ®map_sunxi_rsb, ctx, config,
469 lock_key, lock_name);
470}
471EXPORT_SYMBOL_GPL(__devm_regmap_init_sunxi_rsb);
472
473/* RSB controller driver functions */
474static irqreturn_t sunxi_rsb_irq(int irq, void *dev_id)
475{
476 struct sunxi_rsb *rsb = dev_id;
477 u32 status;
478
479 status = readl(rsb->regs + RSB_INTS);
480 rsb->status = status;
481
482 /* Clear interrupts */
483 status &= (RSB_INTS_LOAD_BSY | RSB_INTS_TRANS_ERR |
484 RSB_INTS_TRANS_OVER);
485 writel(status, rsb->regs + RSB_INTS);
486
487 complete(&rsb->complete);
488
489 return IRQ_HANDLED;
490}
491
492static int sunxi_rsb_init_device_mode(struct sunxi_rsb *rsb)
493{
494 int ret = 0;
495 u32 reg;
496
497 /* send init sequence */
498 writel(RSB_DMCR_DEVICE_START | RSB_DMCR_MODE_DATA |
499 RSB_DMCR_MODE_REG | RSB_DMCR_DEV_ADDR, rsb->regs + RSB_DMCR);
500
501 readl_poll_timeout(rsb->regs + RSB_DMCR, reg,
502 !(reg & RSB_DMCR_DEVICE_START), 100, 250000);
503 if (reg & RSB_DMCR_DEVICE_START)
504 ret = -ETIMEDOUT;
505
506 /* clear interrupt status bits */
507 writel(readl(rsb->regs + RSB_INTS), rsb->regs + RSB_INTS);
508
509 return ret;
510}
511
512/*
513 * There are 15 valid runtime addresses, though Allwinner typically
514 * skips the first, for unknown reasons, and uses the following three.
515 *
516 * 0x17, 0x2d, 0x3a, 0x4e, 0x59, 0x63, 0x74, 0x8b,
517 * 0x9c, 0xa6, 0xb1, 0xc5, 0xd2, 0xe8, 0xff
518 *
519 * No designs with 2 RSB slave devices sharing identical hardware
520 * addresses on the same bus have been seen in the wild. All designs
521 * use 0x2d for the primary PMIC, 0x3a for the secondary PMIC if
522 * there is one, and 0x45 for peripheral ICs.
523 *
524 * The hardware does not seem to support re-setting runtime addresses.
525 * Attempts to do so result in the slave devices returning a NACK.
526 * Hence we just hardcode the mapping here, like Allwinner does.
527 */
528
529static const struct sunxi_rsb_addr_map sunxi_rsb_addr_maps[] = {
530 { 0x3a3, 0x2d }, /* Primary PMIC: AXP223, AXP809, AXP81X, ... */
531 { 0x745, 0x3a }, /* Secondary PMIC: AXP806, ... */
532 { 0xe89, 0x4e }, /* Peripheral IC: AC100, ... */
533};
534
535static u8 sunxi_rsb_get_rtaddr(u16 hwaddr)
536{
537 int i;
538
539 for (i = 0; i < ARRAY_SIZE(sunxi_rsb_addr_maps); i++)
540 if (hwaddr == sunxi_rsb_addr_maps[i].hwaddr)
541 return sunxi_rsb_addr_maps[i].rtaddr;
542
543 return 0; /* 0 is an invalid runtime address */
544}
545
546static int of_rsb_register_devices(struct sunxi_rsb *rsb)
547{
548 struct device *dev = rsb->dev;
549 struct device_node *child, *np = dev->of_node;
550 u32 hwaddr;
551 u8 rtaddr;
552 int ret;
553
554 if (!np)
555 return -EINVAL;
556
557 /* Runtime addresses for all slaves should be set first */
558 for_each_available_child_of_node(np, child) {
559 dev_dbg(dev, "setting child %s runtime address\n",
560 child->full_name);
561
562 ret = of_property_read_u32(child, "reg", &hwaddr);
563 if (ret) {
564 dev_err(dev, "%s: invalid 'reg' property: %d\n",
565 child->full_name, ret);
566 continue;
567 }
568
569 rtaddr = sunxi_rsb_get_rtaddr(hwaddr);
570 if (!rtaddr) {
571 dev_err(dev, "%s: unknown hardware device address\n",
572 child->full_name);
573 continue;
574 }
575
576 /*
577 * Since no devices have been registered yet, we are the
578 * only ones using the bus, we can skip locking the bus.
579 */
580
581 /* setup command parameters */
582 writel(RSB_CMD_STRA, rsb->regs + RSB_CMD);
583 writel(RSB_DAR_RTA(rtaddr) | RSB_DAR_DA(hwaddr),
584 rsb->regs + RSB_DAR);
585
586 /* send command */
587 ret = _sunxi_rsb_run_xfer(rsb);
588 if (ret)
589 dev_warn(dev, "%s: set runtime address failed: %d\n",
590 child->full_name, ret);
591 }
592
593 /* Then we start adding devices and probing them */
594 for_each_available_child_of_node(np, child) {
595 struct sunxi_rsb_device *rdev;
596
597 dev_dbg(dev, "adding child %s\n", child->full_name);
598
599 ret = of_property_read_u32(child, "reg", &hwaddr);
600 if (ret)
601 continue;
602
603 rtaddr = sunxi_rsb_get_rtaddr(hwaddr);
604 if (!rtaddr)
605 continue;
606
607 rdev = sunxi_rsb_device_create(rsb, child, hwaddr, rtaddr);
608 if (IS_ERR(rdev))
609 dev_err(dev, "failed to add child device %s: %ld\n",
610 child->full_name, PTR_ERR(rdev));
611 }
612
613 return 0;
614}
615
616static const struct of_device_id sunxi_rsb_of_match_table[] = {
617 { .compatible = "allwinner,sun8i-a23-rsb" },
618 {}
619};
620MODULE_DEVICE_TABLE(of, sunxi_rsb_of_match_table);
621
622static int sunxi_rsb_probe(struct platform_device *pdev)
623{
624 struct device *dev = &pdev->dev;
625 struct device_node *np = dev->of_node;
626 struct resource *r;
627 struct sunxi_rsb *rsb;
628 unsigned long p_clk_freq;
629 u32 clk_delay, clk_freq = 3000000;
630 int clk_div, irq, ret;
631 u32 reg;
632
633 of_property_read_u32(np, "clock-frequency", &clk_freq);
634 if (clk_freq > RSB_MAX_FREQ) {
635 dev_err(dev,
636 "clock-frequency (%u Hz) is too high (max = 20MHz)\n",
637 clk_freq);
638 return -EINVAL;
639 }
640
641 rsb = devm_kzalloc(dev, sizeof(*rsb), GFP_KERNEL);
642 if (!rsb)
643 return -ENOMEM;
644
645 rsb->dev = dev;
646 platform_set_drvdata(pdev, rsb);
647 r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
648 rsb->regs = devm_ioremap_resource(dev, r);
649 if (IS_ERR(rsb->regs))
650 return PTR_ERR(rsb->regs);
651
652 irq = platform_get_irq(pdev, 0);
653 if (irq < 0) {
654 dev_err(dev, "failed to retrieve irq: %d\n", irq);
655 return irq;
656 }
657
658 rsb->clk = devm_clk_get(dev, NULL);
659 if (IS_ERR(rsb->clk)) {
660 ret = PTR_ERR(rsb->clk);
661 dev_err(dev, "failed to retrieve clk: %d\n", ret);
662 return ret;
663 }
664
665 ret = clk_prepare_enable(rsb->clk);
666 if (ret) {
667 dev_err(dev, "failed to enable clk: %d\n", ret);
668 return ret;
669 }
670
671 p_clk_freq = clk_get_rate(rsb->clk);
672
673 rsb->rstc = devm_reset_control_get(dev, NULL);
674 if (IS_ERR(rsb->rstc)) {
675 ret = PTR_ERR(rsb->rstc);
676 dev_err(dev, "failed to retrieve reset controller: %d\n", ret);
677 goto err_clk_disable;
678 }
679
680 ret = reset_control_deassert(rsb->rstc);
681 if (ret) {
682 dev_err(dev, "failed to deassert reset line: %d\n", ret);
683 goto err_clk_disable;
684 }
685
686 init_completion(&rsb->complete);
687 mutex_init(&rsb->lock);
688
689 /* reset the controller */
690 writel(RSB_CTRL_SOFT_RST, rsb->regs + RSB_CTRL);
691 readl_poll_timeout(rsb->regs + RSB_CTRL, reg,
692 !(reg & RSB_CTRL_SOFT_RST), 1000, 100000);
693
694 /*
695 * Clock frequency and delay calculation code is from
696 * Allwinner U-boot sources.
697 *
698 * From A83 user manual:
699 * bus clock frequency = parent clock frequency / (2 * (divider + 1))
700 */
701 clk_div = p_clk_freq / clk_freq / 2;
702 if (!clk_div)
703 clk_div = 1;
704 else if (clk_div > RSB_CCR_MAX_CLK_DIV + 1)
705 clk_div = RSB_CCR_MAX_CLK_DIV + 1;
706
707 clk_delay = clk_div >> 1;
708 if (!clk_delay)
709 clk_delay = 1;
710
711 dev_info(dev, "RSB running at %lu Hz\n", p_clk_freq / clk_div / 2);
712 writel(RSB_CCR_SDA_OUT_DELAY(clk_delay) | RSB_CCR_CLK_DIV(clk_div - 1),
713 rsb->regs + RSB_CCR);
714
715 ret = devm_request_irq(dev, irq, sunxi_rsb_irq, 0, RSB_CTRL_NAME, rsb);
716 if (ret) {
717 dev_err(dev, "can't register interrupt handler irq %d: %d\n",
718 irq, ret);
719 goto err_reset_assert;
720 }
721
722 /* initialize all devices on the bus into RSB mode */
723 ret = sunxi_rsb_init_device_mode(rsb);
724 if (ret)
725 dev_warn(dev, "Initialize device mode failed: %d\n", ret);
726
727 of_rsb_register_devices(rsb);
728
729 return 0;
730
731err_reset_assert:
732 reset_control_assert(rsb->rstc);
733
734err_clk_disable:
735 clk_disable_unprepare(rsb->clk);
736
737 return ret;
738}
739
740static int sunxi_rsb_remove(struct platform_device *pdev)
741{
742 struct sunxi_rsb *rsb = platform_get_drvdata(pdev);
743
744 device_for_each_child(rsb->dev, NULL, sunxi_rsb_remove_devices);
745 reset_control_assert(rsb->rstc);
746 clk_disable_unprepare(rsb->clk);
747
748 return 0;
749}
750
751static struct platform_driver sunxi_rsb_driver = {
752 .probe = sunxi_rsb_probe,
753 .remove = sunxi_rsb_remove,
754 .driver = {
755 .name = RSB_CTRL_NAME,
756 .of_match_table = sunxi_rsb_of_match_table,
757 },
758};
759
760static int __init sunxi_rsb_init(void)
761{
762 int ret;
763
764 ret = bus_register(&sunxi_rsb_bus);
765 if (ret) {
766 pr_err("failed to register sunxi sunxi_rsb bus: %d\n", ret);
767 return ret;
768 }
769
770 return platform_driver_register(&sunxi_rsb_driver);
771}
772module_init(sunxi_rsb_init);
773
774static void __exit sunxi_rsb_exit(void)
775{
776 platform_driver_unregister(&sunxi_rsb_driver);
777 bus_unregister(&sunxi_rsb_bus);
778}
779module_exit(sunxi_rsb_exit);
780
781MODULE_AUTHOR("Chen-Yu Tsai <wens@csie.org>");
782MODULE_DESCRIPTION("Allwinner sunXi Reduced Serial Bus controller driver");
783MODULE_LICENSE("GPL v2");