Loading...
Note: File does not exist in v4.6.
1======================================================
2UHID - User-space I/O driver support for HID subsystem
3======================================================
4
5UHID allows user-space to implement HID transport drivers. Please see
6hid-transport.rst for an introduction into HID transport drivers. This document
7relies heavily on the definitions declared there.
8
9With UHID, a user-space transport driver can create kernel hid-devices for each
10device connected to the user-space controlled bus. The UHID API defines the I/O
11events provided from the kernel to user-space and vice versa.
12
13There is an example user-space application in ./samples/uhid/uhid-example.c
14
15The UHID API
16------------
17
18UHID is accessed through a character misc-device. The minor number is allocated
19dynamically so you need to rely on udev (or similar) to create the device node.
20This is /dev/uhid by default.
21
22If a new device is detected by your HID I/O Driver and you want to register this
23device with the HID subsystem, then you need to open /dev/uhid once for each
24device you want to register. All further communication is done by read()'ing or
25write()'ing "struct uhid_event" objects. Non-blocking operations are supported
26by setting O_NONBLOCK::
27
28 struct uhid_event {
29 __u32 type;
30 union {
31 struct uhid_create2_req create2;
32 struct uhid_output_req output;
33 struct uhid_input2_req input2;
34 ...
35 } u;
36 };
37
38The "type" field contains the ID of the event. Depending on the ID different
39payloads are sent. You must not split a single event across multiple read()'s or
40multiple write()'s. A single event must always be sent as a whole. Furthermore,
41only a single event can be sent per read() or write(). Pending data is ignored.
42If you want to handle multiple events in a single syscall, then use vectored
43I/O with readv()/writev().
44The "type" field defines the payload. For each type, there is a
45payload-structure available in the union "u" (except for empty payloads). This
46payload contains management and/or device data.
47
48The first thing you should do is send a UHID_CREATE2 event. This will
49register the device. UHID will respond with a UHID_START event. You can now
50start sending data to and reading data from UHID. However, unless UHID sends the
51UHID_OPEN event, the internally attached HID Device Driver has no user attached.
52That is, you might put your device asleep unless you receive the UHID_OPEN
53event. If you receive the UHID_OPEN event, you should start I/O. If the last
54user closes the HID device, you will receive a UHID_CLOSE event. This may be
55followed by a UHID_OPEN event again and so on. There is no need to perform
56reference-counting in user-space. That is, you will never receive multiple
57UHID_OPEN events without a UHID_CLOSE event. The HID subsystem performs
58ref-counting for you.
59You may decide to ignore UHID_OPEN/UHID_CLOSE, though. I/O is allowed even
60though the device may have no users.
61
62If you want to send data on the interrupt channel to the HID subsystem, you send
63a HID_INPUT2 event with your raw data payload. If the kernel wants to send data
64on the interrupt channel to the device, you will read a UHID_OUTPUT event.
65Data requests on the control channel are currently limited to GET_REPORT and
66SET_REPORT (no other data reports on the control channel are defined so far).
67Those requests are always synchronous. That means, the kernel sends
68UHID_GET_REPORT and UHID_SET_REPORT events and requires you to forward them to
69the device on the control channel. Once the device responds, you must forward
70the response via UHID_GET_REPORT_REPLY and UHID_SET_REPORT_REPLY to the kernel.
71The kernel blocks internal driver-execution during such round-trips (times out
72after a hard-coded period).
73
74If your device disconnects, you should send a UHID_DESTROY event. This will
75unregister the device. You can now send UHID_CREATE2 again to register a new
76device.
77If you close() the fd, the device is automatically unregistered and destroyed
78internally.
79
80write()
81-------
82write() allows you to modify the state of the device and feed input data into
83the kernel. The kernel will parse the event immediately and if the event ID is
84not supported, it will return -EOPNOTSUPP. If the payload is invalid, then
85-EINVAL is returned, otherwise, the amount of data that was read is returned and
86the request was handled successfully. O_NONBLOCK does not affect write() as
87writes are always handled immediately in a non-blocking fashion. Future requests
88might make use of O_NONBLOCK, though.
89
90UHID_CREATE2:
91 This creates the internal HID device. No I/O is possible until you send this
92 event to the kernel. The payload is of type struct uhid_create2_req and
93 contains information about your device. You can start I/O now.
94
95UHID_DESTROY:
96 This destroys the internal HID device. No further I/O will be accepted. There
97 may still be pending messages that you can receive with read() but no further
98 UHID_INPUT events can be sent to the kernel.
99 You can create a new device by sending UHID_CREATE2 again. There is no need to
100 reopen the character device.
101
102UHID_INPUT2:
103 You must send UHID_CREATE2 before sending input to the kernel! This event
104 contains a data-payload. This is the raw data that you read from your device
105 on the interrupt channel. The kernel will parse the HID reports.
106
107UHID_GET_REPORT_REPLY:
108 If you receive a UHID_GET_REPORT request you must answer with this request.
109 You must copy the "id" field from the request into the answer. Set the "err"
110 field to 0 if no error occurred or to EIO if an I/O error occurred.
111 If "err" is 0 then you should fill the buffer of the answer with the results
112 of the GET_REPORT request and set "size" correspondingly.
113
114UHID_SET_REPORT_REPLY:
115 This is the SET_REPORT equivalent of UHID_GET_REPORT_REPLY. Unlike GET_REPORT,
116 SET_REPORT never returns a data buffer, therefore, it's sufficient to set the
117 "id" and "err" fields correctly.
118
119read()
120------
121read() will return a queued output report. No reaction is required to any of
122them but you should handle them according to your needs.
123
124UHID_START:
125 This is sent when the HID device is started. Consider this as an answer to
126 UHID_CREATE2. This is always the first event that is sent. Note that this
127 event might not be available immediately after write(UHID_CREATE2) returns.
128 Device drivers might require delayed setups.
129 This event contains a payload of type uhid_start_req. The "dev_flags" field
130 describes special behaviors of a device. The following flags are defined:
131
132 - UHID_DEV_NUMBERED_FEATURE_REPORTS
133 - UHID_DEV_NUMBERED_OUTPUT_REPORTS
134 - UHID_DEV_NUMBERED_INPUT_REPORTS
135
136 Each of these flags defines whether a given report-type uses numbered
137 reports. If numbered reports are used for a type, all messages from
138 the kernel already have the report-number as prefix. Otherwise, no
139 prefix is added by the kernel.
140 For messages sent by user-space to the kernel, you must adjust the
141 prefixes according to these flags.
142
143UHID_STOP:
144 This is sent when the HID device is stopped. Consider this as an answer to
145 UHID_DESTROY.
146
147 If you didn't destroy your device via UHID_DESTROY, but the kernel sends an
148 UHID_STOP event, this should usually be ignored. It means that the kernel
149 reloaded/changed the device driver loaded on your HID device (or some other
150 maintenance actions happened).
151
152 You can usually ignore any UHID_STOP events safely.
153
154UHID_OPEN:
155 This is sent when the HID device is opened. That is, the data that the HID
156 device provides is read by some other process. You may ignore this event but
157 it is useful for power-management. As long as you haven't received this event
158 there is actually no other process that reads your data so there is no need to
159 send UHID_INPUT2 events to the kernel.
160
161UHID_CLOSE:
162 This is sent when there are no more processes which read the HID data. It is
163 the counterpart of UHID_OPEN and you may as well ignore this event.
164
165UHID_OUTPUT:
166 This is sent if the HID device driver wants to send raw data to the I/O
167 device on the interrupt channel. You should read the payload and forward it to
168 the device. The payload is of type "struct uhid_output_req".
169 This may be received even though you haven't received UHID_OPEN yet.
170
171UHID_GET_REPORT:
172 This event is sent if the kernel driver wants to perform a GET_REPORT request
173 on the control channel as described in the HID specs. The report-type and
174 report-number are available in the payload.
175 The kernel serializes GET_REPORT requests so there will never be two in
176 parallel. However, if you fail to respond with a UHID_GET_REPORT_REPLY, the
177 request might silently time out.
178 Once you read a GET_REPORT request, you shall forward it to the HID device and
179 remember the "id" field in the payload. Once your HID device responds to the
180 GET_REPORT (or if it fails), you must send a UHID_GET_REPORT_REPLY to the
181 kernel with the exact same "id" as in the request. If the request already
182 timed out, the kernel will ignore the response silently. The "id" field is
183 never re-used, so conflicts cannot happen.
184
185UHID_SET_REPORT:
186 This is the SET_REPORT equivalent of UHID_GET_REPORT. On receipt, you shall
187 send a SET_REPORT request to your HID device. Once it replies, you must tell
188 the kernel about it via UHID_SET_REPORT_REPLY.
189 The same restrictions as for UHID_GET_REPORT apply.
190
191----------------------------------------------------
192
193Written 2012, David Herrmann <dh.herrmann@gmail.com>