Loading...
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# Network device configuration
4#
5
6menuconfig NETDEVICES
7 default y if UML
8 depends on NET
9 bool "Network device support"
10 help
11 You can say N here if you don't intend to connect your Linux box to
12 any other computer at all.
13
14 You'll have to say Y if your computer contains a network card that
15 you want to use under Linux. If you are going to run SLIP or PPP over
16 telephone line or null modem cable you need say Y here. Connecting
17 two machines with parallel ports using PLIP needs this, as well as
18 AX.25/KISS for sending Internet traffic over amateur radio links.
19
20 See also "The Linux Network Administrator's Guide" by Olaf Kirch and
21 Terry Dawson. Available at <http://www.tldp.org/guides.html>.
22
23 If unsure, say Y.
24
25# All the following symbols are dependent on NETDEVICES - do not repeat
26# that for each of the symbols.
27if NETDEVICES
28
29config MII
30 tristate
31
32config NET_CORE
33 default y
34 bool "Network core driver support"
35 help
36 You can say N here if you do not intend to use any of the
37 networking core drivers (i.e. VLAN, bridging, bonding, etc.)
38
39if NET_CORE
40
41config BONDING
42 tristate "Bonding driver support"
43 depends on INET
44 depends on IPV6 || IPV6=n
45 depends on TLS || TLS_DEVICE=n
46 help
47 Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
48 Channels together. This is called 'Etherchannel' by Cisco,
49 'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
50
51 The driver supports multiple bonding modes to allow for both high
52 performance and high availability operation.
53
54 Refer to <file:Documentation/networking/bonding.rst> for more
55 information.
56
57 To compile this driver as a module, choose M here: the module
58 will be called bonding.
59
60config DUMMY
61 tristate "Dummy net driver support"
62 help
63 This is essentially a bit-bucket device (i.e. traffic you send to
64 this device is consigned into oblivion) with a configurable IP
65 address. It is most commonly used in order to make your currently
66 inactive SLIP address seem like a real address for local programs.
67 If you use SLIP or PPP, you might want to say Y here. It won't
68 enlarge your kernel. What a deal. Read about it in the Network
69 Administrator's Guide, available from
70 <http://www.tldp.org/docs.html#guide>.
71
72 To compile this driver as a module, choose M here: the module
73 will be called dummy.
74
75config WIREGUARD
76 tristate "WireGuard secure network tunnel"
77 depends on NET && INET
78 depends on IPV6 || !IPV6
79 depends on !KMSAN # KMSAN doesn't support the crypto configs below
80 select NET_UDP_TUNNEL
81 select DST_CACHE
82 select CRYPTO
83 select CRYPTO_LIB_CURVE25519
84 select CRYPTO_LIB_CHACHA20POLY1305
85 select CRYPTO_CHACHA20_X86_64 if X86 && 64BIT
86 select CRYPTO_POLY1305_X86_64 if X86 && 64BIT
87 select CRYPTO_BLAKE2S_X86 if X86 && 64BIT
88 select CRYPTO_CURVE25519_X86 if X86 && 64BIT
89 select CRYPTO_CHACHA20_NEON if ARM || (ARM64 && KERNEL_MODE_NEON)
90 select CRYPTO_POLY1305_NEON if ARM64 && KERNEL_MODE_NEON
91 select CRYPTO_POLY1305_ARM if ARM
92 select CRYPTO_BLAKE2S_ARM if ARM
93 select CRYPTO_CURVE25519_NEON if ARM && KERNEL_MODE_NEON
94 select CRYPTO_CHACHA_MIPS if CPU_MIPS32_R2
95 select CRYPTO_POLY1305_MIPS if MIPS
96 select CRYPTO_CHACHA_S390 if S390
97 help
98 WireGuard is a secure, fast, and easy to use replacement for IPSec
99 that uses modern cryptography and clever networking tricks. It's
100 designed to be fairly general purpose and abstract enough to fit most
101 use cases, while at the same time remaining extremely simple to
102 configure. See www.wireguard.com for more info.
103
104 It's safe to say Y or M here, as the driver is very lightweight and
105 is only in use when an administrator chooses to add an interface.
106
107config WIREGUARD_DEBUG
108 bool "Debugging checks and verbose messages"
109 depends on WIREGUARD
110 help
111 This will write log messages for handshake and other events
112 that occur for a WireGuard interface. It will also perform some
113 extra validation checks and unit tests at various points. This is
114 only useful for debugging.
115
116 Say N here unless you know what you're doing.
117
118config EQUALIZER
119 tristate "EQL (serial line load balancing) support"
120 help
121 If you have two serial connections to some other computer (this
122 usually requires two modems and two telephone lines) and you use
123 SLIP (the protocol for sending Internet traffic over telephone
124 lines) or PPP (a better SLIP) on them, you can make them behave like
125 one double speed connection using this driver. Naturally, this has
126 to be supported at the other end as well, either with a similar EQL
127 Linux driver or with a Livingston Portmaster 2e.
128
129 Say Y if you want this and read
130 <file:Documentation/networking/eql.rst>. You may also want to read
131 section 6.2 of the NET-3-HOWTO, available from
132 <http://www.tldp.org/docs.html#howto>.
133
134 To compile this driver as a module, choose M here: the module
135 will be called eql. If unsure, say N.
136
137config NET_FC
138 bool "Fibre Channel driver support"
139 depends on SCSI && PCI
140 help
141 Fibre Channel is a high speed serial protocol mainly used to connect
142 large storage devices to the computer; it is compatible with and
143 intended to replace SCSI.
144
145 If you intend to use Fibre Channel, you need to have a Fibre channel
146 adaptor card in your computer; say Y here and to the driver for your
147 adaptor below. You also should have said Y to "SCSI support" and
148 "SCSI generic support".
149
150config IFB
151 tristate "Intermediate Functional Block support"
152 depends on NET_ACT_MIRRED || NFT_FWD_NETDEV
153 select NET_REDIRECT
154 help
155 This is an intermediate driver that allows sharing of
156 resources.
157 To compile this driver as a module, choose M here: the module
158 will be called ifb. If you want to use more than one ifb
159 device at a time, you need to compile this driver as a module.
160 Instead of 'ifb', the devices will then be called 'ifb0',
161 'ifb1' etc.
162 Look at the iproute2 documentation directory for usage etc
163
164source "drivers/net/team/Kconfig"
165
166config MACVLAN
167 tristate "MAC-VLAN support"
168 help
169 This allows one to create virtual interfaces that map packets to
170 or from specific MAC addresses to a particular interface.
171
172 Macvlan devices can be added using the "ip" command from the
173 iproute2 package starting with the iproute2-2.6.23 release:
174
175 "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"
176
177 To compile this driver as a module, choose M here: the module
178 will be called macvlan.
179
180config MACVTAP
181 tristate "MAC-VLAN based tap driver"
182 depends on MACVLAN
183 depends on INET
184 select TAP
185 help
186 This adds a specialized tap character device driver that is based
187 on the MAC-VLAN network interface, called macvtap. A macvtap device
188 can be added in the same way as a macvlan device, using 'type
189 macvtap', and then be accessed through the tap user space interface.
190
191 To compile this driver as a module, choose M here: the module
192 will be called macvtap.
193
194config IPVLAN_L3S
195 depends on NETFILTER
196 depends on IPVLAN
197 def_bool y
198 select NET_L3_MASTER_DEV
199
200config IPVLAN
201 tristate "IP-VLAN support"
202 depends on INET
203 depends on IPV6 || !IPV6
204 help
205 This allows one to create virtual devices off of a main interface
206 and packets will be delivered based on the dest L3 (IPv6/IPv4 addr)
207 on packets. All interfaces (including the main interface) share L2
208 making it transparent to the connected L2 switch.
209
210 Ipvlan devices can be added using the "ip" command from the
211 iproute2 package starting with the iproute2-3.19 release:
212
213 "ip link add link <main-dev> [ NAME ] type ipvlan"
214
215 To compile this driver as a module, choose M here: the module
216 will be called ipvlan.
217
218config IPVTAP
219 tristate "IP-VLAN based tap driver"
220 depends on IPVLAN
221 depends on INET
222 select TAP
223 help
224 This adds a specialized tap character device driver that is based
225 on the IP-VLAN network interface, called ipvtap. An ipvtap device
226 can be added in the same way as a ipvlan device, using 'type
227 ipvtap', and then be accessed through the tap user space interface.
228
229 To compile this driver as a module, choose M here: the module
230 will be called ipvtap.
231
232config VXLAN
233 tristate "Virtual eXtensible Local Area Network (VXLAN)"
234 depends on INET
235 select NET_UDP_TUNNEL
236 select GRO_CELLS
237 help
238 This allows one to create vxlan virtual interfaces that provide
239 Layer 2 Networks over Layer 3 Networks. VXLAN is often used
240 to tunnel virtual network infrastructure in virtualized environments.
241 For more information see:
242 http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-02
243
244 To compile this driver as a module, choose M here: the module
245 will be called vxlan.
246
247config GENEVE
248 tristate "Generic Network Virtualization Encapsulation"
249 depends on INET
250 depends on IPV6 || !IPV6
251 select NET_UDP_TUNNEL
252 select GRO_CELLS
253 help
254 This allows one to create geneve virtual interfaces that provide
255 Layer 2 Networks over Layer 3 Networks. GENEVE is often used
256 to tunnel virtual network infrastructure in virtualized environments.
257 For more information see:
258 http://tools.ietf.org/html/draft-gross-geneve-02
259
260 To compile this driver as a module, choose M here: the module
261 will be called geneve.
262
263config BAREUDP
264 tristate "Bare UDP Encapsulation"
265 depends on INET
266 depends on IPV6 || !IPV6
267 select NET_UDP_TUNNEL
268 select GRO_CELLS
269 help
270 This adds a bare UDP tunnel module for tunnelling different
271 kinds of traffic like MPLS, IP, etc. inside a UDP tunnel.
272
273 To compile this driver as a module, choose M here: the module
274 will be called bareudp.
275
276config GTP
277 tristate "GPRS Tunneling Protocol datapath (GTP-U)"
278 depends on INET
279 select NET_UDP_TUNNEL
280 help
281 This allows one to create gtp virtual interfaces that provide
282 the GPRS Tunneling Protocol datapath (GTP-U). This tunneling protocol
283 is used to prevent subscribers from accessing mobile carrier core
284 network infrastructure. This driver requires a userspace software that
285 implements the signaling protocol (GTP-C) to update its PDP context
286 base, such as OpenGGSN <http://git.osmocom.org/openggsn/). This
287 tunneling protocol is implemented according to the GSM TS 09.60 and
288 3GPP TS 29.060 standards.
289
290 To compile this drivers as a module, choose M here: the module
291 will be called gtp.
292
293config PFCP
294 tristate "Packet Forwarding Control Protocol (PFCP)"
295 depends on INET
296 select NET_UDP_TUNNEL
297 help
298 This allows one to create PFCP virtual interfaces that allows to
299 set up software and hardware offload of PFCP packets.
300 Note that this module does not support PFCP protocol in the kernel space.
301 There is no support for parsing any PFCP messages.
302
303 To compile this drivers as a module, choose M here: the module
304 will be called pfcp.
305
306config AMT
307 tristate "Automatic Multicast Tunneling (AMT)"
308 depends on INET && IP_MULTICAST
309 depends on IPV6 || !IPV6
310 select NET_UDP_TUNNEL
311 help
312 This allows one to create AMT(Automatic Multicast Tunneling)
313 virtual interfaces that provide multicast tunneling.
314 There are two roles, Gateway, and Relay.
315 Gateway Encapsulates IGMP/MLD traffic from listeners to the Relay.
316 Gateway Decapsulates multicast traffic from the Relay to Listeners.
317 Relay Encapsulates multicast traffic from Sources to Gateway.
318 Relay Decapsulates IGMP/MLD traffic from Gateway.
319
320 To compile this drivers as a module, choose M here: the module
321 will be called amt.
322
323config MACSEC
324 tristate "IEEE 802.1AE MAC-level encryption (MACsec)"
325 select CRYPTO
326 select CRYPTO_AES
327 select CRYPTO_GCM
328 select GRO_CELLS
329 help
330 MACsec is an encryption standard for Ethernet.
331
332config NETCONSOLE
333 tristate "Network console logging support"
334 help
335 If you want to log kernel messages over the network, enable this.
336 See <file:Documentation/networking/netconsole.rst> for details.
337
338config NETCONSOLE_DYNAMIC
339 bool "Dynamic reconfiguration of logging targets"
340 depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
341 !(NETCONSOLE=y && CONFIGFS_FS=m)
342 help
343 This option enables the ability to dynamically reconfigure target
344 parameters (interface, IP addresses, port numbers, MAC addresses)
345 at runtime through a userspace interface exported using configfs.
346 See <file:Documentation/networking/netconsole.rst> for details.
347
348config NETCONSOLE_EXTENDED_LOG
349 bool "Set kernel extended message by default"
350 depends on NETCONSOLE
351 default n
352 help
353 Set extended log support for netconsole message. If this option is
354 set, log messages are transmitted with extended metadata header in a
355 format similar to /dev/kmsg. See
356 <file:Documentation/networking/netconsole.rst> for details.
357
358config NETCONSOLE_PREPEND_RELEASE
359 bool "Prepend kernel release version in the message by default"
360 depends on NETCONSOLE_EXTENDED_LOG
361 default n
362 help
363 Set kernel release to be prepended to each netconsole message by
364 default. If this option is set, the kernel release is prepended into
365 the first field of every netconsole message, so, the netconsole
366 server/peer can easily identify what kernel release is logging each
367 message. See <file:Documentation/networking/netconsole.rst> for
368 details.
369
370config NETPOLL
371 def_bool NETCONSOLE
372
373config NET_POLL_CONTROLLER
374 def_bool NETPOLL
375
376config NTB_NETDEV
377 tristate "Virtual Ethernet over NTB Transport"
378 depends on NTB_TRANSPORT
379
380config RIONET
381 tristate "RapidIO Ethernet over messaging driver support"
382 depends on RAPIDIO
383
384config RIONET_TX_SIZE
385 int "Number of outbound queue entries"
386 depends on RIONET
387 default "128"
388
389config RIONET_RX_SIZE
390 int "Number of inbound queue entries"
391 depends on RIONET
392 default "128"
393
394config TUN
395 tristate "Universal TUN/TAP device driver support"
396 depends on INET
397 select CRC32
398 help
399 TUN/TAP provides packet reception and transmission for user space
400 programs. It can be viewed as a simple Point-to-Point or Ethernet
401 device, which instead of receiving packets from a physical media,
402 receives them from user space program and instead of sending packets
403 via physical media writes them to the user space program.
404
405 When a program opens /dev/net/tun, driver creates and registers
406 corresponding net device tunX or tapX. After a program closed above
407 devices, driver will automatically delete tunXX or tapXX device and
408 all routes corresponding to it.
409
410 Please read <file:Documentation/networking/tuntap.rst> for more
411 information.
412
413 To compile this driver as a module, choose M here: the module
414 will be called tun.
415
416 If you don't know what to use this for, you don't need it.
417
418config TAP
419 tristate
420 help
421 This option is selected by any driver implementing tap user space
422 interface for a virtual interface to re-use core tap functionality.
423
424config TUN_VNET_CROSS_LE
425 bool "Support for cross-endian vnet headers on little-endian kernels"
426 default n
427 help
428 This option allows TUN/TAP and MACVTAP device drivers in a
429 little-endian kernel to parse vnet headers that come from a
430 big-endian legacy virtio device.
431
432 Userspace programs can control the feature using the TUNSETVNETBE
433 and TUNGETVNETBE ioctls.
434
435 Unless you have a little-endian system hosting a big-endian virtual
436 machine with a legacy virtio NIC, you should say N.
437
438config VETH
439 tristate "Virtual ethernet pair device"
440 select PAGE_POOL
441 help
442 This device is a local ethernet tunnel. Devices are created in pairs.
443 When one end receives the packet it appears on its pair and vice
444 versa.
445
446config VIRTIO_NET
447 tristate "Virtio network driver"
448 depends on VIRTIO
449 select NET_FAILOVER
450 select DIMLIB
451 help
452 This is the virtual network driver for virtio. It can be used with
453 QEMU based VMMs (like KVM or Xen). Say Y or M.
454
455config NLMON
456 tristate "Virtual netlink monitoring device"
457 help
458 This option enables a monitoring net device for netlink skbs. The
459 purpose of this is to analyze netlink messages with packet sockets.
460 Thus applications like tcpdump will be able to see local netlink
461 messages if they tap into the netlink device, record pcaps for further
462 diagnostics, etc. This is mostly intended for developers or support
463 to debug netlink issues. If unsure, say N.
464
465config NETKIT
466 bool "BPF-programmable network device"
467 depends on BPF_SYSCALL
468 help
469 The netkit device is a virtual networking device where BPF programs
470 can be attached to the device(s) transmission routine in order to
471 implement the driver's internal logic. The device can be configured
472 to operate in L3 or L2 mode. If unsure, say N.
473
474config NET_VRF
475 tristate "Virtual Routing and Forwarding (Lite)"
476 depends on IP_MULTIPLE_TABLES
477 depends on NET_L3_MASTER_DEV
478 depends on IPV6 || IPV6=n
479 depends on IPV6_MULTIPLE_TABLES || IPV6=n
480 help
481 This option enables the support for mapping interfaces into VRF's. The
482 support enables VRF devices.
483
484config VSOCKMON
485 tristate "Virtual vsock monitoring device"
486 depends on VHOST_VSOCK
487 help
488 This option enables a monitoring net device for vsock sockets. It is
489 mostly intended for developers or support to debug vsock issues. If
490 unsure, say N.
491
492config MHI_NET
493 tristate "MHI network driver"
494 depends on MHI_BUS
495 help
496 This is the network driver for MHI bus. It can be used with
497 QCOM based WWAN modems for IP or QMAP/rmnet protocol (like SDX55).
498 Say Y or M.
499
500endif # NET_CORE
501
502config SUNGEM_PHY
503 tristate
504
505source "drivers/net/arcnet/Kconfig"
506
507source "drivers/atm/Kconfig"
508
509source "drivers/net/caif/Kconfig"
510
511source "drivers/net/dsa/Kconfig"
512
513source "drivers/net/ethernet/Kconfig"
514
515source "drivers/net/fddi/Kconfig"
516
517source "drivers/net/hippi/Kconfig"
518
519source "drivers/net/ipa/Kconfig"
520
521config NET_SB1000
522 tristate "General Instruments Surfboard 1000"
523 depends on ISA && PNP
524 help
525 This is a driver for the General Instrument (also known as
526 NextLevel) SURFboard 1000 internal
527 cable modem. This is an ISA card which is used by a number of cable
528 TV companies to provide cable modem access. It's a one-way
529 downstream-only cable modem, meaning that your upstream net link is
530 provided by your regular phone modem.
531
532 At present this driver only compiles as a module, so say M here if
533 you have this card. The module will be called sb1000. Then read
534 <file:Documentation/networking/device_drivers/cable/sb1000.rst> for
535 information on how to use this module, as it needs special ppp
536 scripts for establishing a connection. Further documentation
537 and the necessary scripts can be found at:
538
539 <http://www.jacksonville.net/~fventuri/>
540 <http://home.adelphia.net/~siglercm/sb1000.html>
541 <http://linuxpower.cx/~cable/>
542
543 If you don't have this card, of course say N.
544
545source "drivers/net/phy/Kconfig"
546
547source "drivers/net/pse-pd/Kconfig"
548
549source "drivers/net/can/Kconfig"
550
551source "drivers/net/mctp/Kconfig"
552
553source "drivers/net/mdio/Kconfig"
554
555source "drivers/net/pcs/Kconfig"
556
557source "drivers/net/plip/Kconfig"
558
559source "drivers/net/ppp/Kconfig"
560
561source "drivers/net/slip/Kconfig"
562
563source "drivers/s390/net/Kconfig"
564
565source "drivers/net/usb/Kconfig"
566
567source "drivers/net/wireless/Kconfig"
568
569source "drivers/net/wan/Kconfig"
570
571source "drivers/net/ieee802154/Kconfig"
572
573source "drivers/net/wwan/Kconfig"
574
575config XEN_NETDEV_FRONTEND
576 tristate "Xen network device frontend driver"
577 depends on XEN
578 select XEN_XENBUS_FRONTEND
579 select PAGE_POOL
580 default y
581 help
582 This driver provides support for Xen paravirtual network
583 devices exported by a Xen network driver domain (often
584 domain 0).
585
586 The corresponding Linux backend driver is enabled by the
587 CONFIG_XEN_NETDEV_BACKEND option.
588
589 If you are compiling a kernel for use as Xen guest, you
590 should say Y here. To compile this driver as a module, chose
591 M here: the module will be called xen-netfront.
592
593config XEN_NETDEV_BACKEND
594 tristate "Xen backend network device"
595 depends on XEN_BACKEND
596 help
597 This driver allows the kernel to act as a Xen network driver
598 domain which exports paravirtual network devices to other
599 Xen domains. These devices can be accessed by any operating
600 system that implements a compatible front end.
601
602 The corresponding Linux frontend driver is enabled by the
603 CONFIG_XEN_NETDEV_FRONTEND configuration option.
604
605 The backend driver presents a standard network device
606 endpoint for each paravirtual network device to the driver
607 domain network stack. These can then be bridged or routed
608 etc in order to provide full network connectivity.
609
610 If you are compiling a kernel to run in a Xen network driver
611 domain (often this is domain 0) you should say Y here. To
612 compile this driver as a module, chose M here: the module
613 will be called xen-netback.
614
615config VMXNET3
616 tristate "VMware VMXNET3 ethernet driver"
617 depends on PCI && INET
618 depends on PAGE_SIZE_LESS_THAN_64KB
619 select PAGE_POOL
620 help
621 This driver supports VMware's vmxnet3 virtual ethernet NIC.
622 To compile this driver as a module, choose M here: the
623 module will be called vmxnet3.
624
625config FUJITSU_ES
626 tristate "FUJITSU Extended Socket Network Device driver"
627 depends on ACPI
628 help
629 This driver provides support for Extended Socket network device
630 on Extended Partitioning of FUJITSU PRIMEQUEST 2000 E2 series.
631
632source "drivers/net/thunderbolt/Kconfig"
633source "drivers/net/hyperv/Kconfig"
634
635config NETDEVSIM
636 tristate "Simulated networking device"
637 depends on DEBUG_FS
638 depends on INET
639 depends on IPV6 || IPV6=n
640 depends on PSAMPLE || PSAMPLE=n
641 depends on PTP_1588_CLOCK_MOCK || PTP_1588_CLOCK_MOCK=n
642 select NET_DEVLINK
643 select PAGE_POOL
644 select NET_SHAPER
645 help
646 This driver is a developer testing tool and software model that can
647 be used to test various control path networking APIs, especially
648 HW-offload related.
649
650 To compile this driver as a module, choose M here: the module
651 will be called netdevsim.
652
653config NET_FAILOVER
654 tristate "Failover driver"
655 select FAILOVER
656 help
657 This provides an automated failover mechanism via APIs to create
658 and destroy a failover master netdev and manages a primary and
659 standby slave netdevs that get registered via the generic failover
660 infrastructure. This can be used by paravirtual drivers to enable
661 an alternate low latency datapath. It also enables live migration of
662 a VM with direct attached VF by failing over to the paravirtual
663 datapath when the VF is unplugged.
664
665config NETDEV_LEGACY_INIT
666 bool
667 depends on ISA
668 help
669 Drivers that call netdev_boot_setup_check() should select this
670 symbol, everything else no longer needs it.
671
672endif # NETDEVICES
1#
2# Network device configuration
3#
4
5menuconfig NETDEVICES
6 default y if UML
7 depends on NET
8 bool "Network device support"
9 ---help---
10 You can say N here if you don't intend to connect your Linux box to
11 any other computer at all.
12
13 You'll have to say Y if your computer contains a network card that
14 you want to use under Linux. If you are going to run SLIP or PPP over
15 telephone line or null modem cable you need say Y here. Connecting
16 two machines with parallel ports using PLIP needs this, as well as
17 AX.25/KISS for sending Internet traffic over amateur radio links.
18
19 See also "The Linux Network Administrator's Guide" by Olaf Kirch and
20 Terry Dawson. Available at <http://www.tldp.org/guides.html>.
21
22 If unsure, say Y.
23
24# All the following symbols are dependent on NETDEVICES - do not repeat
25# that for each of the symbols.
26if NETDEVICES
27
28config MII
29 tristate
30
31config NET_CORE
32 default y
33 bool "Network core driver support"
34 ---help---
35 You can say N here if you do not intend to use any of the
36 networking core drivers (i.e. VLAN, bridging, bonding, etc.)
37
38if NET_CORE
39
40config BONDING
41 tristate "Bonding driver support"
42 depends on INET
43 depends on IPV6 || IPV6=n
44 ---help---
45 Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
46 Channels together. This is called 'Etherchannel' by Cisco,
47 'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
48
49 The driver supports multiple bonding modes to allow for both high
50 performance and high availability operation.
51
52 Refer to <file:Documentation/networking/bonding.txt> for more
53 information.
54
55 To compile this driver as a module, choose M here: the module
56 will be called bonding.
57
58config DUMMY
59 tristate "Dummy net driver support"
60 ---help---
61 This is essentially a bit-bucket device (i.e. traffic you send to
62 this device is consigned into oblivion) with a configurable IP
63 address. It is most commonly used in order to make your currently
64 inactive SLIP address seem like a real address for local programs.
65 If you use SLIP or PPP, you might want to say Y here. It won't
66 enlarge your kernel. What a deal. Read about it in the Network
67 Administrator's Guide, available from
68 <http://www.tldp.org/docs.html#guide>.
69
70 To compile this driver as a module, choose M here: the module
71 will be called dummy.
72
73config EQUALIZER
74 tristate "EQL (serial line load balancing) support"
75 ---help---
76 If you have two serial connections to some other computer (this
77 usually requires two modems and two telephone lines) and you use
78 SLIP (the protocol for sending Internet traffic over telephone
79 lines) or PPP (a better SLIP) on them, you can make them behave like
80 one double speed connection using this driver. Naturally, this has
81 to be supported at the other end as well, either with a similar EQL
82 Linux driver or with a Livingston Portmaster 2e.
83
84 Say Y if you want this and read
85 <file:Documentation/networking/eql.txt>. You may also want to read
86 section 6.2 of the NET-3-HOWTO, available from
87 <http://www.tldp.org/docs.html#howto>.
88
89 To compile this driver as a module, choose M here: the module
90 will be called eql. If unsure, say N.
91
92config NET_FC
93 bool "Fibre Channel driver support"
94 depends on SCSI && PCI
95 help
96 Fibre Channel is a high speed serial protocol mainly used to connect
97 large storage devices to the computer; it is compatible with and
98 intended to replace SCSI.
99
100 If you intend to use Fibre Channel, you need to have a Fibre channel
101 adaptor card in your computer; say Y here and to the driver for your
102 adaptor below. You also should have said Y to "SCSI support" and
103 "SCSI generic support".
104
105config IFB
106 tristate "Intermediate Functional Block support"
107 depends on NET_CLS_ACT
108 ---help---
109 This is an intermediate driver that allows sharing of
110 resources.
111 To compile this driver as a module, choose M here: the module
112 will be called ifb. If you want to use more than one ifb
113 device at a time, you need to compile this driver as a module.
114 Instead of 'ifb', the devices will then be called 'ifb0',
115 'ifb1' etc.
116 Look at the iproute2 documentation directory for usage etc
117
118source "drivers/net/team/Kconfig"
119
120config MACVLAN
121 tristate "MAC-VLAN support"
122 ---help---
123 This allows one to create virtual interfaces that map packets to
124 or from specific MAC addresses to a particular interface.
125
126 Macvlan devices can be added using the "ip" command from the
127 iproute2 package starting with the iproute2-2.6.23 release:
128
129 "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"
130
131 To compile this driver as a module, choose M here: the module
132 will be called macvlan.
133
134config MACVTAP
135 tristate "MAC-VLAN based tap driver"
136 depends on MACVLAN
137 depends on INET
138 help
139 This adds a specialized tap character device driver that is based
140 on the MAC-VLAN network interface, called macvtap. A macvtap device
141 can be added in the same way as a macvlan device, using 'type
142 macvtap', and then be accessed through the tap user space interface.
143
144 To compile this driver as a module, choose M here: the module
145 will be called macvtap.
146
147
148config IPVLAN
149 tristate "IP-VLAN support"
150 depends on INET
151 depends on IPV6
152 ---help---
153 This allows one to create virtual devices off of a main interface
154 and packets will be delivered based on the dest L3 (IPv6/IPv4 addr)
155 on packets. All interfaces (including the main interface) share L2
156 making it transparent to the connected L2 switch.
157
158 Ipvlan devices can be added using the "ip" command from the
159 iproute2 package starting with the iproute2-3.19 release:
160
161 "ip link add link <main-dev> [ NAME ] type ipvlan"
162
163 To compile this driver as a module, choose M here: the module
164 will be called ipvlan.
165
166
167config VXLAN
168 tristate "Virtual eXtensible Local Area Network (VXLAN)"
169 depends on INET
170 select NET_UDP_TUNNEL
171 ---help---
172 This allows one to create vxlan virtual interfaces that provide
173 Layer 2 Networks over Layer 3 Networks. VXLAN is often used
174 to tunnel virtual network infrastructure in virtualized environments.
175 For more information see:
176 http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-02
177
178 To compile this driver as a module, choose M here: the module
179 will be called vxlan.
180
181config GENEVE
182 tristate "Generic Network Virtualization Encapsulation"
183 depends on INET && NET_UDP_TUNNEL
184 select NET_IP_TUNNEL
185 ---help---
186 This allows one to create geneve virtual interfaces that provide
187 Layer 2 Networks over Layer 3 Networks. GENEVE is often used
188 to tunnel virtual network infrastructure in virtualized environments.
189 For more information see:
190 http://tools.ietf.org/html/draft-gross-geneve-02
191
192 To compile this driver as a module, choose M here: the module
193 will be called geneve.
194
195config MACSEC
196 tristate "IEEE 802.1AE MAC-level encryption (MACsec)"
197 select CRYPTO
198 select CRYPTO_AES
199 select CRYPTO_GCM
200 ---help---
201 MACsec is an encryption standard for Ethernet.
202
203config NETCONSOLE
204 tristate "Network console logging support"
205 ---help---
206 If you want to log kernel messages over the network, enable this.
207 See <file:Documentation/networking/netconsole.txt> for details.
208
209config NETCONSOLE_DYNAMIC
210 bool "Dynamic reconfiguration of logging targets"
211 depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
212 !(NETCONSOLE=y && CONFIGFS_FS=m)
213 help
214 This option enables the ability to dynamically reconfigure target
215 parameters (interface, IP addresses, port numbers, MAC addresses)
216 at runtime through a userspace interface exported using configfs.
217 See <file:Documentation/networking/netconsole.txt> for details.
218
219config NETPOLL
220 def_bool NETCONSOLE
221 select SRCU
222
223config NET_POLL_CONTROLLER
224 def_bool NETPOLL
225
226config NTB_NETDEV
227 tristate "Virtual Ethernet over NTB Transport"
228 depends on NTB_TRANSPORT
229
230config RIONET
231 tristate "RapidIO Ethernet over messaging driver support"
232 depends on RAPIDIO
233
234config RIONET_TX_SIZE
235 int "Number of outbound queue entries"
236 depends on RIONET
237 default "128"
238
239config RIONET_RX_SIZE
240 int "Number of inbound queue entries"
241 depends on RIONET
242 default "128"
243
244config TUN
245 tristate "Universal TUN/TAP device driver support"
246 depends on INET
247 select CRC32
248 ---help---
249 TUN/TAP provides packet reception and transmission for user space
250 programs. It can be viewed as a simple Point-to-Point or Ethernet
251 device, which instead of receiving packets from a physical media,
252 receives them from user space program and instead of sending packets
253 via physical media writes them to the user space program.
254
255 When a program opens /dev/net/tun, driver creates and registers
256 corresponding net device tunX or tapX. After a program closed above
257 devices, driver will automatically delete tunXX or tapXX device and
258 all routes corresponding to it.
259
260 Please read <file:Documentation/networking/tuntap.txt> for more
261 information.
262
263 To compile this driver as a module, choose M here: the module
264 will be called tun.
265
266 If you don't know what to use this for, you don't need it.
267
268config TUN_VNET_CROSS_LE
269 bool "Support for cross-endian vnet headers on little-endian kernels"
270 default n
271 ---help---
272 This option allows TUN/TAP and MACVTAP device drivers in a
273 little-endian kernel to parse vnet headers that come from a
274 big-endian legacy virtio device.
275
276 Userspace programs can control the feature using the TUNSETVNETBE
277 and TUNGETVNETBE ioctls.
278
279 Unless you have a little-endian system hosting a big-endian virtual
280 machine with a legacy virtio NIC, you should say N.
281
282config VETH
283 tristate "Virtual ethernet pair device"
284 ---help---
285 This device is a local ethernet tunnel. Devices are created in pairs.
286 When one end receives the packet it appears on its pair and vice
287 versa.
288
289config VIRTIO_NET
290 tristate "Virtio network driver"
291 depends on VIRTIO
292 ---help---
293 This is the virtual network driver for virtio. It can be used with
294 lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
295
296config NLMON
297 tristate "Virtual netlink monitoring device"
298 ---help---
299 This option enables a monitoring net device for netlink skbs. The
300 purpose of this is to analyze netlink messages with packet sockets.
301 Thus applications like tcpdump will be able to see local netlink
302 messages if they tap into the netlink device, record pcaps for further
303 diagnostics, etc. This is mostly intended for developers or support
304 to debug netlink issues. If unsure, say N.
305
306config NET_VRF
307 tristate "Virtual Routing and Forwarding (Lite)"
308 depends on IP_MULTIPLE_TABLES
309 depends on NET_L3_MASTER_DEV
310 depends on IPV6 || IPV6=n
311 depends on IPV6_MULTIPLE_TABLES || IPV6=n
312 ---help---
313 This option enables the support for mapping interfaces into VRF's. The
314 support enables VRF devices.
315
316endif # NET_CORE
317
318config SUNGEM_PHY
319 tristate
320
321source "drivers/net/arcnet/Kconfig"
322
323source "drivers/atm/Kconfig"
324
325source "drivers/net/caif/Kconfig"
326
327source "drivers/net/dsa/Kconfig"
328
329source "drivers/net/ethernet/Kconfig"
330
331source "drivers/net/fddi/Kconfig"
332
333source "drivers/net/hippi/Kconfig"
334
335config NET_SB1000
336 tristate "General Instruments Surfboard 1000"
337 depends on PNP
338 ---help---
339 This is a driver for the General Instrument (also known as
340 NextLevel) SURFboard 1000 internal
341 cable modem. This is an ISA card which is used by a number of cable
342 TV companies to provide cable modem access. It's a one-way
343 downstream-only cable modem, meaning that your upstream net link is
344 provided by your regular phone modem.
345
346 At present this driver only compiles as a module, so say M here if
347 you have this card. The module will be called sb1000. Then read
348 <file:Documentation/networking/README.sb1000> for information on how
349 to use this module, as it needs special ppp scripts for establishing
350 a connection. Further documentation and the necessary scripts can be
351 found at:
352
353 <http://www.jacksonville.net/~fventuri/>
354 <http://home.adelphia.net/~siglercm/sb1000.html>
355 <http://linuxpower.cx/~cable/>
356
357 If you don't have this card, of course say N.
358
359source "drivers/net/phy/Kconfig"
360
361source "drivers/net/plip/Kconfig"
362
363source "drivers/net/ppp/Kconfig"
364
365source "drivers/net/slip/Kconfig"
366
367source "drivers/s390/net/Kconfig"
368
369source "drivers/net/usb/Kconfig"
370
371source "drivers/net/wireless/Kconfig"
372
373source "drivers/net/wimax/Kconfig"
374
375source "drivers/net/wan/Kconfig"
376
377source "drivers/net/ieee802154/Kconfig"
378
379config XEN_NETDEV_FRONTEND
380 tristate "Xen network device frontend driver"
381 depends on XEN
382 select XEN_XENBUS_FRONTEND
383 default y
384 help
385 This driver provides support for Xen paravirtual network
386 devices exported by a Xen network driver domain (often
387 domain 0).
388
389 The corresponding Linux backend driver is enabled by the
390 CONFIG_XEN_NETDEV_BACKEND option.
391
392 If you are compiling a kernel for use as Xen guest, you
393 should say Y here. To compile this driver as a module, chose
394 M here: the module will be called xen-netfront.
395
396config XEN_NETDEV_BACKEND
397 tristate "Xen backend network device"
398 depends on XEN_BACKEND
399 help
400 This driver allows the kernel to act as a Xen network driver
401 domain which exports paravirtual network devices to other
402 Xen domains. These devices can be accessed by any operating
403 system that implements a compatible front end.
404
405 The corresponding Linux frontend driver is enabled by the
406 CONFIG_XEN_NETDEV_FRONTEND configuration option.
407
408 The backend driver presents a standard network device
409 endpoint for each paravirtual network device to the driver
410 domain network stack. These can then be bridged or routed
411 etc in order to provide full network connectivity.
412
413 If you are compiling a kernel to run in a Xen network driver
414 domain (often this is domain 0) you should say Y here. To
415 compile this driver as a module, chose M here: the module
416 will be called xen-netback.
417
418config VMXNET3
419 tristate "VMware VMXNET3 ethernet driver"
420 depends on PCI && INET
421 help
422 This driver supports VMware's vmxnet3 virtual ethernet NIC.
423 To compile this driver as a module, choose M here: the
424 module will be called vmxnet3.
425
426config FUJITSU_ES
427 tristate "FUJITSU Extended Socket Network Device driver"
428 depends on ACPI
429 help
430 This driver provides support for Extended Socket network device
431 on Extended Partitioning of FUJITSU PRIMEQUEST 2000 E2 series.
432
433source "drivers/net/hyperv/Kconfig"
434
435endif # NETDEVICES