Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 *
4 * Generic Bluetooth USB driver
5 *
6 * Copyright (C) 2005-2008 Marcel Holtmann <marcel@holtmann.org>
7 */
8
9#include <linux/dmi.h>
10#include <linux/module.h>
11#include <linux/usb.h>
12#include <linux/usb/quirks.h>
13#include <linux/firmware.h>
14#include <linux/iopoll.h>
15#include <linux/of_device.h>
16#include <linux/of_irq.h>
17#include <linux/suspend.h>
18#include <linux/gpio/consumer.h>
19#include <linux/debugfs.h>
20#include <linux/unaligned.h>
21
22#include <net/bluetooth/bluetooth.h>
23#include <net/bluetooth/hci_core.h>
24
25#include "btintel.h"
26#include "btbcm.h"
27#include "btrtl.h"
28#include "btmtk.h"
29
30#define VERSION "0.8"
31
32static bool disable_scofix;
33static bool force_scofix;
34static bool enable_autosuspend = IS_ENABLED(CONFIG_BT_HCIBTUSB_AUTOSUSPEND);
35static bool enable_poll_sync = IS_ENABLED(CONFIG_BT_HCIBTUSB_POLL_SYNC);
36static bool reset = true;
37
38static struct usb_driver btusb_driver;
39
40#define BTUSB_IGNORE BIT(0)
41#define BTUSB_DIGIANSWER BIT(1)
42#define BTUSB_CSR BIT(2)
43#define BTUSB_SNIFFER BIT(3)
44#define BTUSB_BCM92035 BIT(4)
45#define BTUSB_BROKEN_ISOC BIT(5)
46#define BTUSB_WRONG_SCO_MTU BIT(6)
47#define BTUSB_ATH3012 BIT(7)
48#define BTUSB_INTEL_COMBINED BIT(8)
49#define BTUSB_INTEL_BOOT BIT(9)
50#define BTUSB_BCM_PATCHRAM BIT(10)
51#define BTUSB_MARVELL BIT(11)
52#define BTUSB_SWAVE BIT(12)
53#define BTUSB_AMP BIT(13)
54#define BTUSB_QCA_ROME BIT(14)
55#define BTUSB_BCM_APPLE BIT(15)
56#define BTUSB_REALTEK BIT(16)
57#define BTUSB_BCM2045 BIT(17)
58#define BTUSB_IFNUM_2 BIT(18)
59#define BTUSB_CW6622 BIT(19)
60#define BTUSB_MEDIATEK BIT(20)
61#define BTUSB_WIDEBAND_SPEECH BIT(21)
62#define BTUSB_INVALID_LE_STATES BIT(22)
63#define BTUSB_QCA_WCN6855 BIT(23)
64#define BTUSB_INTEL_BROKEN_SHUTDOWN_LED BIT(24)
65#define BTUSB_INTEL_BROKEN_INITIAL_NCMD BIT(25)
66#define BTUSB_INTEL_NO_WBS_SUPPORT BIT(26)
67#define BTUSB_ACTIONS_SEMI BIT(27)
68
69static const struct usb_device_id btusb_table[] = {
70 /* Generic Bluetooth USB device */
71 { USB_DEVICE_INFO(0xe0, 0x01, 0x01) },
72
73 /* Generic Bluetooth AMP device */
74 { USB_DEVICE_INFO(0xe0, 0x01, 0x04), .driver_info = BTUSB_AMP },
75
76 /* Generic Bluetooth USB interface */
77 { USB_INTERFACE_INFO(0xe0, 0x01, 0x01) },
78
79 /* Apple-specific (Broadcom) devices */
80 { USB_VENDOR_AND_INTERFACE_INFO(0x05ac, 0xff, 0x01, 0x01),
81 .driver_info = BTUSB_BCM_APPLE | BTUSB_IFNUM_2 },
82
83 /* MediaTek MT76x0E */
84 { USB_DEVICE(0x0e8d, 0x763f) },
85
86 /* Broadcom SoftSailing reporting vendor specific */
87 { USB_DEVICE(0x0a5c, 0x21e1) },
88
89 /* Apple MacBookPro 7,1 */
90 { USB_DEVICE(0x05ac, 0x8213) },
91
92 /* Apple iMac11,1 */
93 { USB_DEVICE(0x05ac, 0x8215) },
94
95 /* Apple MacBookPro6,2 */
96 { USB_DEVICE(0x05ac, 0x8218) },
97
98 /* Apple MacBookAir3,1, MacBookAir3,2 */
99 { USB_DEVICE(0x05ac, 0x821b) },
100
101 /* Apple MacBookAir4,1 */
102 { USB_DEVICE(0x05ac, 0x821f) },
103
104 /* Apple MacBookPro8,2 */
105 { USB_DEVICE(0x05ac, 0x821a) },
106
107 /* Apple MacMini5,1 */
108 { USB_DEVICE(0x05ac, 0x8281) },
109
110 /* AVM BlueFRITZ! USB v2.0 */
111 { USB_DEVICE(0x057c, 0x3800), .driver_info = BTUSB_SWAVE },
112
113 /* Bluetooth Ultraport Module from IBM */
114 { USB_DEVICE(0x04bf, 0x030a) },
115
116 /* ALPS Modules with non-standard id */
117 { USB_DEVICE(0x044e, 0x3001) },
118 { USB_DEVICE(0x044e, 0x3002) },
119
120 /* Ericsson with non-standard id */
121 { USB_DEVICE(0x0bdb, 0x1002) },
122
123 /* Canyon CN-BTU1 with HID interfaces */
124 { USB_DEVICE(0x0c10, 0x0000) },
125
126 /* Broadcom BCM20702B0 (Dynex/Insignia) */
127 { USB_DEVICE(0x19ff, 0x0239), .driver_info = BTUSB_BCM_PATCHRAM },
128
129 /* Broadcom BCM43142A0 (Foxconn/Lenovo) */
130 { USB_VENDOR_AND_INTERFACE_INFO(0x105b, 0xff, 0x01, 0x01),
131 .driver_info = BTUSB_BCM_PATCHRAM },
132
133 /* Broadcom BCM920703 (HTC Vive) */
134 { USB_VENDOR_AND_INTERFACE_INFO(0x0bb4, 0xff, 0x01, 0x01),
135 .driver_info = BTUSB_BCM_PATCHRAM },
136
137 /* Foxconn - Hon Hai */
138 { USB_VENDOR_AND_INTERFACE_INFO(0x0489, 0xff, 0x01, 0x01),
139 .driver_info = BTUSB_BCM_PATCHRAM },
140
141 /* Lite-On Technology - Broadcom based */
142 { USB_VENDOR_AND_INTERFACE_INFO(0x04ca, 0xff, 0x01, 0x01),
143 .driver_info = BTUSB_BCM_PATCHRAM },
144
145 /* Broadcom devices with vendor specific id */
146 { USB_VENDOR_AND_INTERFACE_INFO(0x0a5c, 0xff, 0x01, 0x01),
147 .driver_info = BTUSB_BCM_PATCHRAM },
148
149 /* ASUSTek Computer - Broadcom based */
150 { USB_VENDOR_AND_INTERFACE_INFO(0x0b05, 0xff, 0x01, 0x01),
151 .driver_info = BTUSB_BCM_PATCHRAM },
152
153 /* Belkin F8065bf - Broadcom based */
154 { USB_VENDOR_AND_INTERFACE_INFO(0x050d, 0xff, 0x01, 0x01),
155 .driver_info = BTUSB_BCM_PATCHRAM },
156
157 /* IMC Networks - Broadcom based */
158 { USB_VENDOR_AND_INTERFACE_INFO(0x13d3, 0xff, 0x01, 0x01),
159 .driver_info = BTUSB_BCM_PATCHRAM },
160
161 /* Dell Computer - Broadcom based */
162 { USB_VENDOR_AND_INTERFACE_INFO(0x413c, 0xff, 0x01, 0x01),
163 .driver_info = BTUSB_BCM_PATCHRAM },
164
165 /* Toshiba Corp - Broadcom based */
166 { USB_VENDOR_AND_INTERFACE_INFO(0x0930, 0xff, 0x01, 0x01),
167 .driver_info = BTUSB_BCM_PATCHRAM },
168
169 /* Intel Bluetooth USB Bootloader (RAM module) */
170 { USB_DEVICE(0x8087, 0x0a5a),
171 .driver_info = BTUSB_INTEL_BOOT | BTUSB_BROKEN_ISOC },
172
173 { } /* Terminating entry */
174};
175
176MODULE_DEVICE_TABLE(usb, btusb_table);
177
178static const struct usb_device_id quirks_table[] = {
179 /* CSR BlueCore devices */
180 { USB_DEVICE(0x0a12, 0x0001), .driver_info = BTUSB_CSR },
181
182 /* Broadcom BCM2033 without firmware */
183 { USB_DEVICE(0x0a5c, 0x2033), .driver_info = BTUSB_IGNORE },
184
185 /* Broadcom BCM2045 devices */
186 { USB_DEVICE(0x0a5c, 0x2045), .driver_info = BTUSB_BCM2045 },
187
188 /* Atheros 3011 with sflash firmware */
189 { USB_DEVICE(0x0489, 0xe027), .driver_info = BTUSB_IGNORE },
190 { USB_DEVICE(0x0489, 0xe03d), .driver_info = BTUSB_IGNORE },
191 { USB_DEVICE(0x04f2, 0xaff1), .driver_info = BTUSB_IGNORE },
192 { USB_DEVICE(0x0930, 0x0215), .driver_info = BTUSB_IGNORE },
193 { USB_DEVICE(0x0cf3, 0x3002), .driver_info = BTUSB_IGNORE },
194 { USB_DEVICE(0x0cf3, 0xe019), .driver_info = BTUSB_IGNORE },
195 { USB_DEVICE(0x13d3, 0x3304), .driver_info = BTUSB_IGNORE },
196
197 /* Atheros AR9285 Malbec with sflash firmware */
198 { USB_DEVICE(0x03f0, 0x311d), .driver_info = BTUSB_IGNORE },
199
200 /* Atheros 3012 with sflash firmware */
201 { USB_DEVICE(0x0489, 0xe04d), .driver_info = BTUSB_ATH3012 },
202 { USB_DEVICE(0x0489, 0xe04e), .driver_info = BTUSB_ATH3012 },
203 { USB_DEVICE(0x0489, 0xe056), .driver_info = BTUSB_ATH3012 },
204 { USB_DEVICE(0x0489, 0xe057), .driver_info = BTUSB_ATH3012 },
205 { USB_DEVICE(0x0489, 0xe05f), .driver_info = BTUSB_ATH3012 },
206 { USB_DEVICE(0x0489, 0xe076), .driver_info = BTUSB_ATH3012 },
207 { USB_DEVICE(0x0489, 0xe078), .driver_info = BTUSB_ATH3012 },
208 { USB_DEVICE(0x0489, 0xe095), .driver_info = BTUSB_ATH3012 },
209 { USB_DEVICE(0x04c5, 0x1330), .driver_info = BTUSB_ATH3012 },
210 { USB_DEVICE(0x04ca, 0x3004), .driver_info = BTUSB_ATH3012 },
211 { USB_DEVICE(0x04ca, 0x3005), .driver_info = BTUSB_ATH3012 },
212 { USB_DEVICE(0x04ca, 0x3006), .driver_info = BTUSB_ATH3012 },
213 { USB_DEVICE(0x04ca, 0x3007), .driver_info = BTUSB_ATH3012 },
214 { USB_DEVICE(0x04ca, 0x3008), .driver_info = BTUSB_ATH3012 },
215 { USB_DEVICE(0x04ca, 0x300b), .driver_info = BTUSB_ATH3012 },
216 { USB_DEVICE(0x04ca, 0x300d), .driver_info = BTUSB_ATH3012 },
217 { USB_DEVICE(0x04ca, 0x300f), .driver_info = BTUSB_ATH3012 },
218 { USB_DEVICE(0x04ca, 0x3010), .driver_info = BTUSB_ATH3012 },
219 { USB_DEVICE(0x04ca, 0x3014), .driver_info = BTUSB_ATH3012 },
220 { USB_DEVICE(0x04ca, 0x3018), .driver_info = BTUSB_ATH3012 },
221 { USB_DEVICE(0x0930, 0x0219), .driver_info = BTUSB_ATH3012 },
222 { USB_DEVICE(0x0930, 0x021c), .driver_info = BTUSB_ATH3012 },
223 { USB_DEVICE(0x0930, 0x0220), .driver_info = BTUSB_ATH3012 },
224 { USB_DEVICE(0x0930, 0x0227), .driver_info = BTUSB_ATH3012 },
225 { USB_DEVICE(0x0b05, 0x17d0), .driver_info = BTUSB_ATH3012 },
226 { USB_DEVICE(0x0cf3, 0x0036), .driver_info = BTUSB_ATH3012 },
227 { USB_DEVICE(0x0cf3, 0x3004), .driver_info = BTUSB_ATH3012 },
228 { USB_DEVICE(0x0cf3, 0x3008), .driver_info = BTUSB_ATH3012 },
229 { USB_DEVICE(0x0cf3, 0x311d), .driver_info = BTUSB_ATH3012 },
230 { USB_DEVICE(0x0cf3, 0x311e), .driver_info = BTUSB_ATH3012 },
231 { USB_DEVICE(0x0cf3, 0x311f), .driver_info = BTUSB_ATH3012 },
232 { USB_DEVICE(0x0cf3, 0x3121), .driver_info = BTUSB_ATH3012 },
233 { USB_DEVICE(0x0cf3, 0x817a), .driver_info = BTUSB_ATH3012 },
234 { USB_DEVICE(0x0cf3, 0x817b), .driver_info = BTUSB_ATH3012 },
235 { USB_DEVICE(0x0cf3, 0xe003), .driver_info = BTUSB_ATH3012 },
236 { USB_DEVICE(0x0cf3, 0xe004), .driver_info = BTUSB_ATH3012 },
237 { USB_DEVICE(0x0cf3, 0xe005), .driver_info = BTUSB_ATH3012 },
238 { USB_DEVICE(0x0cf3, 0xe006), .driver_info = BTUSB_ATH3012 },
239 { USB_DEVICE(0x13d3, 0x3362), .driver_info = BTUSB_ATH3012 },
240 { USB_DEVICE(0x13d3, 0x3375), .driver_info = BTUSB_ATH3012 },
241 { USB_DEVICE(0x13d3, 0x3393), .driver_info = BTUSB_ATH3012 },
242 { USB_DEVICE(0x13d3, 0x3395), .driver_info = BTUSB_ATH3012 },
243 { USB_DEVICE(0x13d3, 0x3402), .driver_info = BTUSB_ATH3012 },
244 { USB_DEVICE(0x13d3, 0x3408), .driver_info = BTUSB_ATH3012 },
245 { USB_DEVICE(0x13d3, 0x3423), .driver_info = BTUSB_ATH3012 },
246 { USB_DEVICE(0x13d3, 0x3432), .driver_info = BTUSB_ATH3012 },
247 { USB_DEVICE(0x13d3, 0x3472), .driver_info = BTUSB_ATH3012 },
248 { USB_DEVICE(0x13d3, 0x3474), .driver_info = BTUSB_ATH3012 },
249 { USB_DEVICE(0x13d3, 0x3487), .driver_info = BTUSB_ATH3012 },
250 { USB_DEVICE(0x13d3, 0x3490), .driver_info = BTUSB_ATH3012 },
251
252 /* Atheros AR5BBU12 with sflash firmware */
253 { USB_DEVICE(0x0489, 0xe02c), .driver_info = BTUSB_IGNORE },
254
255 /* Atheros AR5BBU12 with sflash firmware */
256 { USB_DEVICE(0x0489, 0xe036), .driver_info = BTUSB_ATH3012 },
257 { USB_DEVICE(0x0489, 0xe03c), .driver_info = BTUSB_ATH3012 },
258
259 /* QCA ROME chipset */
260 { USB_DEVICE(0x0cf3, 0x535b), .driver_info = BTUSB_QCA_ROME |
261 BTUSB_WIDEBAND_SPEECH },
262 { USB_DEVICE(0x0cf3, 0xe007), .driver_info = BTUSB_QCA_ROME |
263 BTUSB_WIDEBAND_SPEECH },
264 { USB_DEVICE(0x0cf3, 0xe009), .driver_info = BTUSB_QCA_ROME |
265 BTUSB_WIDEBAND_SPEECH },
266 { USB_DEVICE(0x0cf3, 0xe010), .driver_info = BTUSB_QCA_ROME |
267 BTUSB_WIDEBAND_SPEECH },
268 { USB_DEVICE(0x0cf3, 0xe300), .driver_info = BTUSB_QCA_ROME |
269 BTUSB_WIDEBAND_SPEECH },
270 { USB_DEVICE(0x0cf3, 0xe301), .driver_info = BTUSB_QCA_ROME |
271 BTUSB_WIDEBAND_SPEECH },
272 { USB_DEVICE(0x0cf3, 0xe360), .driver_info = BTUSB_QCA_ROME |
273 BTUSB_WIDEBAND_SPEECH },
274 { USB_DEVICE(0x0cf3, 0xe500), .driver_info = BTUSB_QCA_ROME |
275 BTUSB_WIDEBAND_SPEECH },
276 { USB_DEVICE(0x0489, 0xe092), .driver_info = BTUSB_QCA_ROME |
277 BTUSB_WIDEBAND_SPEECH },
278 { USB_DEVICE(0x0489, 0xe09f), .driver_info = BTUSB_QCA_ROME |
279 BTUSB_WIDEBAND_SPEECH },
280 { USB_DEVICE(0x0489, 0xe0a2), .driver_info = BTUSB_QCA_ROME |
281 BTUSB_WIDEBAND_SPEECH },
282 { USB_DEVICE(0x04ca, 0x3011), .driver_info = BTUSB_QCA_ROME |
283 BTUSB_WIDEBAND_SPEECH },
284 { USB_DEVICE(0x04ca, 0x3015), .driver_info = BTUSB_QCA_ROME |
285 BTUSB_WIDEBAND_SPEECH },
286 { USB_DEVICE(0x04ca, 0x3016), .driver_info = BTUSB_QCA_ROME |
287 BTUSB_WIDEBAND_SPEECH },
288 { USB_DEVICE(0x04ca, 0x301a), .driver_info = BTUSB_QCA_ROME |
289 BTUSB_WIDEBAND_SPEECH },
290 { USB_DEVICE(0x04ca, 0x3021), .driver_info = BTUSB_QCA_ROME |
291 BTUSB_WIDEBAND_SPEECH },
292 { USB_DEVICE(0x13d3, 0x3491), .driver_info = BTUSB_QCA_ROME |
293 BTUSB_WIDEBAND_SPEECH },
294 { USB_DEVICE(0x13d3, 0x3496), .driver_info = BTUSB_QCA_ROME |
295 BTUSB_WIDEBAND_SPEECH },
296 { USB_DEVICE(0x13d3, 0x3501), .driver_info = BTUSB_QCA_ROME |
297 BTUSB_WIDEBAND_SPEECH },
298
299 /* QCA WCN6855 chipset */
300 { USB_DEVICE(0x0cf3, 0xe600), .driver_info = BTUSB_QCA_WCN6855 |
301 BTUSB_WIDEBAND_SPEECH },
302 { USB_DEVICE(0x0489, 0xe0cc), .driver_info = BTUSB_QCA_WCN6855 |
303 BTUSB_WIDEBAND_SPEECH },
304 { USB_DEVICE(0x0489, 0xe0d6), .driver_info = BTUSB_QCA_WCN6855 |
305 BTUSB_WIDEBAND_SPEECH },
306 { USB_DEVICE(0x0489, 0xe0e3), .driver_info = BTUSB_QCA_WCN6855 |
307 BTUSB_WIDEBAND_SPEECH },
308 { USB_DEVICE(0x10ab, 0x9309), .driver_info = BTUSB_QCA_WCN6855 |
309 BTUSB_WIDEBAND_SPEECH },
310 { USB_DEVICE(0x10ab, 0x9409), .driver_info = BTUSB_QCA_WCN6855 |
311 BTUSB_WIDEBAND_SPEECH },
312 { USB_DEVICE(0x0489, 0xe0d0), .driver_info = BTUSB_QCA_WCN6855 |
313 BTUSB_WIDEBAND_SPEECH },
314 { USB_DEVICE(0x10ab, 0x9108), .driver_info = BTUSB_QCA_WCN6855 |
315 BTUSB_WIDEBAND_SPEECH },
316 { USB_DEVICE(0x10ab, 0x9109), .driver_info = BTUSB_QCA_WCN6855 |
317 BTUSB_WIDEBAND_SPEECH },
318 { USB_DEVICE(0x10ab, 0x9208), .driver_info = BTUSB_QCA_WCN6855 |
319 BTUSB_WIDEBAND_SPEECH },
320 { USB_DEVICE(0x10ab, 0x9209), .driver_info = BTUSB_QCA_WCN6855 |
321 BTUSB_WIDEBAND_SPEECH },
322 { USB_DEVICE(0x10ab, 0x9308), .driver_info = BTUSB_QCA_WCN6855 |
323 BTUSB_WIDEBAND_SPEECH },
324 { USB_DEVICE(0x10ab, 0x9408), .driver_info = BTUSB_QCA_WCN6855 |
325 BTUSB_WIDEBAND_SPEECH },
326 { USB_DEVICE(0x10ab, 0x9508), .driver_info = BTUSB_QCA_WCN6855 |
327 BTUSB_WIDEBAND_SPEECH },
328 { USB_DEVICE(0x10ab, 0x9509), .driver_info = BTUSB_QCA_WCN6855 |
329 BTUSB_WIDEBAND_SPEECH },
330 { USB_DEVICE(0x10ab, 0x9608), .driver_info = BTUSB_QCA_WCN6855 |
331 BTUSB_WIDEBAND_SPEECH },
332 { USB_DEVICE(0x10ab, 0x9609), .driver_info = BTUSB_QCA_WCN6855 |
333 BTUSB_WIDEBAND_SPEECH },
334 { USB_DEVICE(0x10ab, 0x9f09), .driver_info = BTUSB_QCA_WCN6855 |
335 BTUSB_WIDEBAND_SPEECH },
336 { USB_DEVICE(0x04ca, 0x3022), .driver_info = BTUSB_QCA_WCN6855 |
337 BTUSB_WIDEBAND_SPEECH },
338 { USB_DEVICE(0x0489, 0xe0c7), .driver_info = BTUSB_QCA_WCN6855 |
339 BTUSB_WIDEBAND_SPEECH },
340 { USB_DEVICE(0x0489, 0xe0c9), .driver_info = BTUSB_QCA_WCN6855 |
341 BTUSB_WIDEBAND_SPEECH },
342 { USB_DEVICE(0x0489, 0xe0ca), .driver_info = BTUSB_QCA_WCN6855 |
343 BTUSB_WIDEBAND_SPEECH },
344 { USB_DEVICE(0x0489, 0xe0cb), .driver_info = BTUSB_QCA_WCN6855 |
345 BTUSB_WIDEBAND_SPEECH },
346 { USB_DEVICE(0x0489, 0xe0ce), .driver_info = BTUSB_QCA_WCN6855 |
347 BTUSB_WIDEBAND_SPEECH },
348 { USB_DEVICE(0x0489, 0xe0de), .driver_info = BTUSB_QCA_WCN6855 |
349 BTUSB_WIDEBAND_SPEECH },
350 { USB_DEVICE(0x0489, 0xe0df), .driver_info = BTUSB_QCA_WCN6855 |
351 BTUSB_WIDEBAND_SPEECH },
352 { USB_DEVICE(0x0489, 0xe0e1), .driver_info = BTUSB_QCA_WCN6855 |
353 BTUSB_WIDEBAND_SPEECH },
354 { USB_DEVICE(0x0489, 0xe0ea), .driver_info = BTUSB_QCA_WCN6855 |
355 BTUSB_WIDEBAND_SPEECH },
356 { USB_DEVICE(0x0489, 0xe0ec), .driver_info = BTUSB_QCA_WCN6855 |
357 BTUSB_WIDEBAND_SPEECH },
358 { USB_DEVICE(0x04ca, 0x3023), .driver_info = BTUSB_QCA_WCN6855 |
359 BTUSB_WIDEBAND_SPEECH },
360 { USB_DEVICE(0x04ca, 0x3024), .driver_info = BTUSB_QCA_WCN6855 |
361 BTUSB_WIDEBAND_SPEECH },
362 { USB_DEVICE(0x04ca, 0x3a22), .driver_info = BTUSB_QCA_WCN6855 |
363 BTUSB_WIDEBAND_SPEECH },
364 { USB_DEVICE(0x04ca, 0x3a24), .driver_info = BTUSB_QCA_WCN6855 |
365 BTUSB_WIDEBAND_SPEECH },
366 { USB_DEVICE(0x04ca, 0x3a26), .driver_info = BTUSB_QCA_WCN6855 |
367 BTUSB_WIDEBAND_SPEECH },
368 { USB_DEVICE(0x04ca, 0x3a27), .driver_info = BTUSB_QCA_WCN6855 |
369 BTUSB_WIDEBAND_SPEECH },
370
371 /* QCA WCN785x chipset */
372 { USB_DEVICE(0x0cf3, 0xe700), .driver_info = BTUSB_QCA_WCN6855 |
373 BTUSB_WIDEBAND_SPEECH },
374 { USB_DEVICE(0x0489, 0xe0fc), .driver_info = BTUSB_QCA_WCN6855 |
375 BTUSB_WIDEBAND_SPEECH },
376 { USB_DEVICE(0x0489, 0xe0f3), .driver_info = BTUSB_QCA_WCN6855 |
377 BTUSB_WIDEBAND_SPEECH },
378 { USB_DEVICE(0x13d3, 0x3623), .driver_info = BTUSB_QCA_WCN6855 |
379 BTUSB_WIDEBAND_SPEECH },
380 { USB_DEVICE(0x2c7c, 0x0130), .driver_info = BTUSB_QCA_WCN6855 |
381 BTUSB_WIDEBAND_SPEECH },
382
383 /* Broadcom BCM2035 */
384 { USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 },
385 { USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU },
386 { USB_DEVICE(0x0a5c, 0x2035), .driver_info = BTUSB_WRONG_SCO_MTU },
387
388 /* Broadcom BCM2045 */
389 { USB_DEVICE(0x0a5c, 0x2039), .driver_info = BTUSB_WRONG_SCO_MTU },
390 { USB_DEVICE(0x0a5c, 0x2101), .driver_info = BTUSB_WRONG_SCO_MTU },
391
392 /* IBM/Lenovo ThinkPad with Broadcom chip */
393 { USB_DEVICE(0x0a5c, 0x201e), .driver_info = BTUSB_WRONG_SCO_MTU },
394 { USB_DEVICE(0x0a5c, 0x2110), .driver_info = BTUSB_WRONG_SCO_MTU },
395
396 /* HP laptop with Broadcom chip */
397 { USB_DEVICE(0x03f0, 0x171d), .driver_info = BTUSB_WRONG_SCO_MTU },
398
399 /* Dell laptop with Broadcom chip */
400 { USB_DEVICE(0x413c, 0x8126), .driver_info = BTUSB_WRONG_SCO_MTU },
401
402 /* Dell Wireless 370 and 410 devices */
403 { USB_DEVICE(0x413c, 0x8152), .driver_info = BTUSB_WRONG_SCO_MTU },
404 { USB_DEVICE(0x413c, 0x8156), .driver_info = BTUSB_WRONG_SCO_MTU },
405
406 /* Belkin F8T012 and F8T013 devices */
407 { USB_DEVICE(0x050d, 0x0012), .driver_info = BTUSB_WRONG_SCO_MTU },
408 { USB_DEVICE(0x050d, 0x0013), .driver_info = BTUSB_WRONG_SCO_MTU },
409
410 /* Asus WL-BTD202 device */
411 { USB_DEVICE(0x0b05, 0x1715), .driver_info = BTUSB_WRONG_SCO_MTU },
412
413 /* Kensington Bluetooth USB adapter */
414 { USB_DEVICE(0x047d, 0x105e), .driver_info = BTUSB_WRONG_SCO_MTU },
415
416 /* RTX Telecom based adapters with buggy SCO support */
417 { USB_DEVICE(0x0400, 0x0807), .driver_info = BTUSB_BROKEN_ISOC },
418 { USB_DEVICE(0x0400, 0x080a), .driver_info = BTUSB_BROKEN_ISOC },
419
420 /* CONWISE Technology based adapters with buggy SCO support */
421 { USB_DEVICE(0x0e5e, 0x6622),
422 .driver_info = BTUSB_BROKEN_ISOC | BTUSB_CW6622},
423
424 /* Roper Class 1 Bluetooth Dongle (Silicon Wave based) */
425 { USB_DEVICE(0x1310, 0x0001), .driver_info = BTUSB_SWAVE },
426
427 /* Digianswer devices */
428 { USB_DEVICE(0x08fd, 0x0001), .driver_info = BTUSB_DIGIANSWER },
429 { USB_DEVICE(0x08fd, 0x0002), .driver_info = BTUSB_IGNORE },
430
431 /* CSR BlueCore Bluetooth Sniffer */
432 { USB_DEVICE(0x0a12, 0x0002),
433 .driver_info = BTUSB_SNIFFER | BTUSB_BROKEN_ISOC },
434
435 /* Frontline ComProbe Bluetooth Sniffer */
436 { USB_DEVICE(0x16d3, 0x0002),
437 .driver_info = BTUSB_SNIFFER | BTUSB_BROKEN_ISOC },
438
439 /* Marvell Bluetooth devices */
440 { USB_DEVICE(0x1286, 0x2044), .driver_info = BTUSB_MARVELL },
441 { USB_DEVICE(0x1286, 0x2046), .driver_info = BTUSB_MARVELL },
442 { USB_DEVICE(0x1286, 0x204e), .driver_info = BTUSB_MARVELL },
443
444 /* Intel Bluetooth devices */
445 { USB_DEVICE(0x8087, 0x0025), .driver_info = BTUSB_INTEL_COMBINED },
446 { USB_DEVICE(0x8087, 0x0026), .driver_info = BTUSB_INTEL_COMBINED },
447 { USB_DEVICE(0x8087, 0x0029), .driver_info = BTUSB_INTEL_COMBINED },
448 { USB_DEVICE(0x8087, 0x0032), .driver_info = BTUSB_INTEL_COMBINED },
449 { USB_DEVICE(0x8087, 0x0033), .driver_info = BTUSB_INTEL_COMBINED },
450 { USB_DEVICE(0x8087, 0x0035), .driver_info = BTUSB_INTEL_COMBINED },
451 { USB_DEVICE(0x8087, 0x0036), .driver_info = BTUSB_INTEL_COMBINED },
452 { USB_DEVICE(0x8087, 0x0037), .driver_info = BTUSB_INTEL_COMBINED },
453 { USB_DEVICE(0x8087, 0x0038), .driver_info = BTUSB_INTEL_COMBINED },
454 { USB_DEVICE(0x8087, 0x0039), .driver_info = BTUSB_INTEL_COMBINED },
455 { USB_DEVICE(0x8087, 0x07da), .driver_info = BTUSB_CSR },
456 { USB_DEVICE(0x8087, 0x07dc), .driver_info = BTUSB_INTEL_COMBINED |
457 BTUSB_INTEL_NO_WBS_SUPPORT |
458 BTUSB_INTEL_BROKEN_INITIAL_NCMD |
459 BTUSB_INTEL_BROKEN_SHUTDOWN_LED },
460 { USB_DEVICE(0x8087, 0x0a2a), .driver_info = BTUSB_INTEL_COMBINED |
461 BTUSB_INTEL_NO_WBS_SUPPORT |
462 BTUSB_INTEL_BROKEN_SHUTDOWN_LED },
463 { USB_DEVICE(0x8087, 0x0a2b), .driver_info = BTUSB_INTEL_COMBINED },
464 { USB_DEVICE(0x8087, 0x0aa7), .driver_info = BTUSB_INTEL_COMBINED |
465 BTUSB_INTEL_BROKEN_SHUTDOWN_LED },
466 { USB_DEVICE(0x8087, 0x0aaa), .driver_info = BTUSB_INTEL_COMBINED },
467
468 /* Other Intel Bluetooth devices */
469 { USB_VENDOR_AND_INTERFACE_INFO(0x8087, 0xe0, 0x01, 0x01),
470 .driver_info = BTUSB_IGNORE },
471
472 /* Realtek 8821CE Bluetooth devices */
473 { USB_DEVICE(0x13d3, 0x3529), .driver_info = BTUSB_REALTEK |
474 BTUSB_WIDEBAND_SPEECH },
475
476 /* Realtek 8822CE Bluetooth devices */
477 { USB_DEVICE(0x0bda, 0xb00c), .driver_info = BTUSB_REALTEK |
478 BTUSB_WIDEBAND_SPEECH },
479 { USB_DEVICE(0x0bda, 0xc822), .driver_info = BTUSB_REALTEK |
480 BTUSB_WIDEBAND_SPEECH },
481
482 /* Realtek 8822CU Bluetooth devices */
483 { USB_DEVICE(0x13d3, 0x3549), .driver_info = BTUSB_REALTEK |
484 BTUSB_WIDEBAND_SPEECH },
485
486 /* Realtek 8852AE Bluetooth devices */
487 { USB_DEVICE(0x0bda, 0x2852), .driver_info = BTUSB_REALTEK |
488 BTUSB_WIDEBAND_SPEECH },
489 { USB_DEVICE(0x0bda, 0xc852), .driver_info = BTUSB_REALTEK |
490 BTUSB_WIDEBAND_SPEECH },
491 { USB_DEVICE(0x0bda, 0x385a), .driver_info = BTUSB_REALTEK |
492 BTUSB_WIDEBAND_SPEECH },
493 { USB_DEVICE(0x0bda, 0x4852), .driver_info = BTUSB_REALTEK |
494 BTUSB_WIDEBAND_SPEECH },
495 { USB_DEVICE(0x04c5, 0x165c), .driver_info = BTUSB_REALTEK |
496 BTUSB_WIDEBAND_SPEECH },
497 { USB_DEVICE(0x04ca, 0x4006), .driver_info = BTUSB_REALTEK |
498 BTUSB_WIDEBAND_SPEECH },
499 { USB_DEVICE(0x0cb8, 0xc549), .driver_info = BTUSB_REALTEK |
500 BTUSB_WIDEBAND_SPEECH },
501
502 /* Realtek 8852CE Bluetooth devices */
503 { USB_DEVICE(0x04ca, 0x4007), .driver_info = BTUSB_REALTEK |
504 BTUSB_WIDEBAND_SPEECH },
505 { USB_DEVICE(0x04c5, 0x1675), .driver_info = BTUSB_REALTEK |
506 BTUSB_WIDEBAND_SPEECH },
507 { USB_DEVICE(0x0cb8, 0xc558), .driver_info = BTUSB_REALTEK |
508 BTUSB_WIDEBAND_SPEECH },
509 { USB_DEVICE(0x13d3, 0x3587), .driver_info = BTUSB_REALTEK |
510 BTUSB_WIDEBAND_SPEECH },
511 { USB_DEVICE(0x13d3, 0x3586), .driver_info = BTUSB_REALTEK |
512 BTUSB_WIDEBAND_SPEECH },
513 { USB_DEVICE(0x13d3, 0x3592), .driver_info = BTUSB_REALTEK |
514 BTUSB_WIDEBAND_SPEECH },
515 { USB_DEVICE(0x0489, 0xe122), .driver_info = BTUSB_REALTEK |
516 BTUSB_WIDEBAND_SPEECH },
517
518 /* Realtek 8852BE Bluetooth devices */
519 { USB_DEVICE(0x0cb8, 0xc559), .driver_info = BTUSB_REALTEK |
520 BTUSB_WIDEBAND_SPEECH },
521 { USB_DEVICE(0x0bda, 0x4853), .driver_info = BTUSB_REALTEK |
522 BTUSB_WIDEBAND_SPEECH },
523 { USB_DEVICE(0x0bda, 0x887b), .driver_info = BTUSB_REALTEK |
524 BTUSB_WIDEBAND_SPEECH },
525 { USB_DEVICE(0x0bda, 0xb85b), .driver_info = BTUSB_REALTEK |
526 BTUSB_WIDEBAND_SPEECH },
527 { USB_DEVICE(0x13d3, 0x3570), .driver_info = BTUSB_REALTEK |
528 BTUSB_WIDEBAND_SPEECH },
529 { USB_DEVICE(0x13d3, 0x3571), .driver_info = BTUSB_REALTEK |
530 BTUSB_WIDEBAND_SPEECH },
531 { USB_DEVICE(0x13d3, 0x3572), .driver_info = BTUSB_REALTEK |
532 BTUSB_WIDEBAND_SPEECH },
533 { USB_DEVICE(0x13d3, 0x3591), .driver_info = BTUSB_REALTEK |
534 BTUSB_WIDEBAND_SPEECH },
535 { USB_DEVICE(0x0489, 0xe123), .driver_info = BTUSB_REALTEK |
536 BTUSB_WIDEBAND_SPEECH },
537 { USB_DEVICE(0x0489, 0xe125), .driver_info = BTUSB_REALTEK |
538 BTUSB_WIDEBAND_SPEECH },
539
540 /* Realtek 8852BT/8852BE-VT Bluetooth devices */
541 { USB_DEVICE(0x0bda, 0x8520), .driver_info = BTUSB_REALTEK |
542 BTUSB_WIDEBAND_SPEECH },
543
544 /* Realtek 8922AE Bluetooth devices */
545 { USB_DEVICE(0x0bda, 0x8922), .driver_info = BTUSB_REALTEK |
546 BTUSB_WIDEBAND_SPEECH },
547 { USB_DEVICE(0x13d3, 0x3617), .driver_info = BTUSB_REALTEK |
548 BTUSB_WIDEBAND_SPEECH },
549 { USB_DEVICE(0x13d3, 0x3616), .driver_info = BTUSB_REALTEK |
550 BTUSB_WIDEBAND_SPEECH },
551 { USB_DEVICE(0x0489, 0xe130), .driver_info = BTUSB_REALTEK |
552 BTUSB_WIDEBAND_SPEECH },
553
554 /* Realtek Bluetooth devices */
555 { USB_VENDOR_AND_INTERFACE_INFO(0x0bda, 0xe0, 0x01, 0x01),
556 .driver_info = BTUSB_REALTEK },
557
558 /* MediaTek Bluetooth devices */
559 { USB_VENDOR_AND_INTERFACE_INFO(0x0e8d, 0xe0, 0x01, 0x01),
560 .driver_info = BTUSB_MEDIATEK |
561 BTUSB_WIDEBAND_SPEECH },
562
563 /* Additional MediaTek MT7615E Bluetooth devices */
564 { USB_DEVICE(0x13d3, 0x3560), .driver_info = BTUSB_MEDIATEK},
565
566 /* Additional MediaTek MT7663 Bluetooth devices */
567 { USB_DEVICE(0x043e, 0x310c), .driver_info = BTUSB_MEDIATEK |
568 BTUSB_WIDEBAND_SPEECH },
569 { USB_DEVICE(0x04ca, 0x3801), .driver_info = BTUSB_MEDIATEK |
570 BTUSB_WIDEBAND_SPEECH },
571
572 /* Additional MediaTek MT7668 Bluetooth devices */
573 { USB_DEVICE(0x043e, 0x3109), .driver_info = BTUSB_MEDIATEK |
574 BTUSB_WIDEBAND_SPEECH },
575
576 /* Additional MediaTek MT7920 Bluetooth devices */
577 { USB_DEVICE(0x0489, 0xe134), .driver_info = BTUSB_MEDIATEK |
578 BTUSB_WIDEBAND_SPEECH },
579 { USB_DEVICE(0x13d3, 0x3620), .driver_info = BTUSB_MEDIATEK |
580 BTUSB_WIDEBAND_SPEECH },
581 { USB_DEVICE(0x13d3, 0x3621), .driver_info = BTUSB_MEDIATEK |
582 BTUSB_WIDEBAND_SPEECH },
583 { USB_DEVICE(0x13d3, 0x3622), .driver_info = BTUSB_MEDIATEK |
584 BTUSB_WIDEBAND_SPEECH },
585
586 /* Additional MediaTek MT7921 Bluetooth devices */
587 { USB_DEVICE(0x0489, 0xe0c8), .driver_info = BTUSB_MEDIATEK |
588 BTUSB_WIDEBAND_SPEECH },
589 { USB_DEVICE(0x0489, 0xe0cd), .driver_info = BTUSB_MEDIATEK |
590 BTUSB_WIDEBAND_SPEECH },
591 { USB_DEVICE(0x0489, 0xe0e0), .driver_info = BTUSB_MEDIATEK |
592 BTUSB_WIDEBAND_SPEECH },
593 { USB_DEVICE(0x0489, 0xe0f2), .driver_info = BTUSB_MEDIATEK |
594 BTUSB_WIDEBAND_SPEECH },
595 { USB_DEVICE(0x04ca, 0x3802), .driver_info = BTUSB_MEDIATEK |
596 BTUSB_WIDEBAND_SPEECH },
597 { USB_DEVICE(0x0e8d, 0x0608), .driver_info = BTUSB_MEDIATEK |
598 BTUSB_WIDEBAND_SPEECH },
599 { USB_DEVICE(0x13d3, 0x3563), .driver_info = BTUSB_MEDIATEK |
600 BTUSB_WIDEBAND_SPEECH },
601 { USB_DEVICE(0x13d3, 0x3564), .driver_info = BTUSB_MEDIATEK |
602 BTUSB_WIDEBAND_SPEECH },
603 { USB_DEVICE(0x13d3, 0x3567), .driver_info = BTUSB_MEDIATEK |
604 BTUSB_WIDEBAND_SPEECH },
605 { USB_DEVICE(0x13d3, 0x3578), .driver_info = BTUSB_MEDIATEK |
606 BTUSB_WIDEBAND_SPEECH },
607 { USB_DEVICE(0x13d3, 0x3583), .driver_info = BTUSB_MEDIATEK |
608 BTUSB_WIDEBAND_SPEECH },
609 { USB_DEVICE(0x13d3, 0x3606), .driver_info = BTUSB_MEDIATEK |
610 BTUSB_WIDEBAND_SPEECH },
611
612 /* MediaTek MT7922 Bluetooth devices */
613 { USB_DEVICE(0x13d3, 0x3585), .driver_info = BTUSB_MEDIATEK |
614 BTUSB_WIDEBAND_SPEECH },
615 { USB_DEVICE(0x13d3, 0x3610), .driver_info = BTUSB_MEDIATEK |
616 BTUSB_WIDEBAND_SPEECH },
617
618 /* MediaTek MT7922A Bluetooth devices */
619 { USB_DEVICE(0x0489, 0xe0d8), .driver_info = BTUSB_MEDIATEK |
620 BTUSB_WIDEBAND_SPEECH },
621 { USB_DEVICE(0x0489, 0xe0d9), .driver_info = BTUSB_MEDIATEK |
622 BTUSB_WIDEBAND_SPEECH },
623 { USB_DEVICE(0x0489, 0xe0e2), .driver_info = BTUSB_MEDIATEK |
624 BTUSB_WIDEBAND_SPEECH },
625 { USB_DEVICE(0x0489, 0xe0e4), .driver_info = BTUSB_MEDIATEK |
626 BTUSB_WIDEBAND_SPEECH },
627 { USB_DEVICE(0x0489, 0xe0f1), .driver_info = BTUSB_MEDIATEK |
628 BTUSB_WIDEBAND_SPEECH },
629 { USB_DEVICE(0x0489, 0xe0f2), .driver_info = BTUSB_MEDIATEK |
630 BTUSB_WIDEBAND_SPEECH },
631 { USB_DEVICE(0x0489, 0xe0f5), .driver_info = BTUSB_MEDIATEK |
632 BTUSB_WIDEBAND_SPEECH },
633 { USB_DEVICE(0x0489, 0xe0f6), .driver_info = BTUSB_MEDIATEK |
634 BTUSB_WIDEBAND_SPEECH },
635 { USB_DEVICE(0x0489, 0xe102), .driver_info = BTUSB_MEDIATEK |
636 BTUSB_WIDEBAND_SPEECH },
637 { USB_DEVICE(0x04ca, 0x3804), .driver_info = BTUSB_MEDIATEK |
638 BTUSB_WIDEBAND_SPEECH },
639 { USB_DEVICE(0x04ca, 0x38e4), .driver_info = BTUSB_MEDIATEK |
640 BTUSB_WIDEBAND_SPEECH },
641 { USB_DEVICE(0x13d3, 0x3568), .driver_info = BTUSB_MEDIATEK |
642 BTUSB_WIDEBAND_SPEECH },
643 { USB_DEVICE(0x13d3, 0x3605), .driver_info = BTUSB_MEDIATEK |
644 BTUSB_WIDEBAND_SPEECH },
645 { USB_DEVICE(0x13d3, 0x3607), .driver_info = BTUSB_MEDIATEK |
646 BTUSB_WIDEBAND_SPEECH },
647 { USB_DEVICE(0x13d3, 0x3614), .driver_info = BTUSB_MEDIATEK |
648 BTUSB_WIDEBAND_SPEECH },
649 { USB_DEVICE(0x13d3, 0x3615), .driver_info = BTUSB_MEDIATEK |
650 BTUSB_WIDEBAND_SPEECH },
651 { USB_DEVICE(0x35f5, 0x7922), .driver_info = BTUSB_MEDIATEK |
652 BTUSB_WIDEBAND_SPEECH },
653
654 /* Additional MediaTek MT7925 Bluetooth devices */
655 { USB_DEVICE(0x0489, 0xe111), .driver_info = BTUSB_MEDIATEK |
656 BTUSB_WIDEBAND_SPEECH },
657 { USB_DEVICE(0x0489, 0xe113), .driver_info = BTUSB_MEDIATEK |
658 BTUSB_WIDEBAND_SPEECH },
659 { USB_DEVICE(0x0489, 0xe118), .driver_info = BTUSB_MEDIATEK |
660 BTUSB_WIDEBAND_SPEECH },
661 { USB_DEVICE(0x0489, 0xe11e), .driver_info = BTUSB_MEDIATEK |
662 BTUSB_WIDEBAND_SPEECH },
663 { USB_DEVICE(0x0489, 0xe124), .driver_info = BTUSB_MEDIATEK |
664 BTUSB_WIDEBAND_SPEECH },
665 { USB_DEVICE(0x0489, 0xe139), .driver_info = BTUSB_MEDIATEK |
666 BTUSB_WIDEBAND_SPEECH },
667 { USB_DEVICE(0x0489, 0xe14f), .driver_info = BTUSB_MEDIATEK |
668 BTUSB_WIDEBAND_SPEECH },
669 { USB_DEVICE(0x0489, 0xe150), .driver_info = BTUSB_MEDIATEK |
670 BTUSB_WIDEBAND_SPEECH },
671 { USB_DEVICE(0x0489, 0xe151), .driver_info = BTUSB_MEDIATEK |
672 BTUSB_WIDEBAND_SPEECH },
673 { USB_DEVICE(0x13d3, 0x3602), .driver_info = BTUSB_MEDIATEK |
674 BTUSB_WIDEBAND_SPEECH },
675 { USB_DEVICE(0x13d3, 0x3603), .driver_info = BTUSB_MEDIATEK |
676 BTUSB_WIDEBAND_SPEECH },
677 { USB_DEVICE(0x13d3, 0x3604), .driver_info = BTUSB_MEDIATEK |
678 BTUSB_WIDEBAND_SPEECH },
679 { USB_DEVICE(0x13d3, 0x3608), .driver_info = BTUSB_MEDIATEK |
680 BTUSB_WIDEBAND_SPEECH },
681 { USB_DEVICE(0x13d3, 0x3628), .driver_info = BTUSB_MEDIATEK |
682 BTUSB_WIDEBAND_SPEECH },
683
684 /* Additional Realtek 8723AE Bluetooth devices */
685 { USB_DEVICE(0x0930, 0x021d), .driver_info = BTUSB_REALTEK },
686 { USB_DEVICE(0x13d3, 0x3394), .driver_info = BTUSB_REALTEK },
687
688 /* Additional Realtek 8723BE Bluetooth devices */
689 { USB_DEVICE(0x0489, 0xe085), .driver_info = BTUSB_REALTEK },
690 { USB_DEVICE(0x0489, 0xe08b), .driver_info = BTUSB_REALTEK },
691 { USB_DEVICE(0x04f2, 0xb49f), .driver_info = BTUSB_REALTEK },
692 { USB_DEVICE(0x13d3, 0x3410), .driver_info = BTUSB_REALTEK },
693 { USB_DEVICE(0x13d3, 0x3416), .driver_info = BTUSB_REALTEK },
694 { USB_DEVICE(0x13d3, 0x3459), .driver_info = BTUSB_REALTEK },
695 { USB_DEVICE(0x13d3, 0x3494), .driver_info = BTUSB_REALTEK },
696
697 /* Additional Realtek 8723BU Bluetooth devices */
698 { USB_DEVICE(0x7392, 0xa611), .driver_info = BTUSB_REALTEK },
699
700 /* Additional Realtek 8723DE Bluetooth devices */
701 { USB_DEVICE(0x0bda, 0xb009), .driver_info = BTUSB_REALTEK },
702 { USB_DEVICE(0x2ff8, 0xb011), .driver_info = BTUSB_REALTEK },
703
704 /* Additional Realtek 8761BUV Bluetooth devices */
705 { USB_DEVICE(0x2357, 0x0604), .driver_info = BTUSB_REALTEK |
706 BTUSB_WIDEBAND_SPEECH },
707 { USB_DEVICE(0x0b05, 0x190e), .driver_info = BTUSB_REALTEK |
708 BTUSB_WIDEBAND_SPEECH },
709 { USB_DEVICE(0x2550, 0x8761), .driver_info = BTUSB_REALTEK |
710 BTUSB_WIDEBAND_SPEECH },
711 { USB_DEVICE(0x0bda, 0x8771), .driver_info = BTUSB_REALTEK |
712 BTUSB_WIDEBAND_SPEECH },
713 { USB_DEVICE(0x6655, 0x8771), .driver_info = BTUSB_REALTEK |
714 BTUSB_WIDEBAND_SPEECH },
715 { USB_DEVICE(0x7392, 0xc611), .driver_info = BTUSB_REALTEK |
716 BTUSB_WIDEBAND_SPEECH },
717 { USB_DEVICE(0x2b89, 0x8761), .driver_info = BTUSB_REALTEK |
718 BTUSB_WIDEBAND_SPEECH },
719
720 /* Additional Realtek 8821AE Bluetooth devices */
721 { USB_DEVICE(0x0b05, 0x17dc), .driver_info = BTUSB_REALTEK },
722 { USB_DEVICE(0x13d3, 0x3414), .driver_info = BTUSB_REALTEK },
723 { USB_DEVICE(0x13d3, 0x3458), .driver_info = BTUSB_REALTEK },
724 { USB_DEVICE(0x13d3, 0x3461), .driver_info = BTUSB_REALTEK },
725 { USB_DEVICE(0x13d3, 0x3462), .driver_info = BTUSB_REALTEK },
726
727 /* Additional Realtek 8822BE Bluetooth devices */
728 { USB_DEVICE(0x13d3, 0x3526), .driver_info = BTUSB_REALTEK },
729 { USB_DEVICE(0x0b05, 0x185c), .driver_info = BTUSB_REALTEK },
730
731 /* Additional Realtek 8822CE Bluetooth devices */
732 { USB_DEVICE(0x04ca, 0x4005), .driver_info = BTUSB_REALTEK |
733 BTUSB_WIDEBAND_SPEECH },
734 { USB_DEVICE(0x04c5, 0x161f), .driver_info = BTUSB_REALTEK |
735 BTUSB_WIDEBAND_SPEECH },
736 { USB_DEVICE(0x0b05, 0x18ef), .driver_info = BTUSB_REALTEK |
737 BTUSB_WIDEBAND_SPEECH },
738 { USB_DEVICE(0x13d3, 0x3548), .driver_info = BTUSB_REALTEK |
739 BTUSB_WIDEBAND_SPEECH },
740 { USB_DEVICE(0x13d3, 0x3549), .driver_info = BTUSB_REALTEK |
741 BTUSB_WIDEBAND_SPEECH },
742 { USB_DEVICE(0x13d3, 0x3553), .driver_info = BTUSB_REALTEK |
743 BTUSB_WIDEBAND_SPEECH },
744 { USB_DEVICE(0x13d3, 0x3555), .driver_info = BTUSB_REALTEK |
745 BTUSB_WIDEBAND_SPEECH },
746 { USB_DEVICE(0x2ff8, 0x3051), .driver_info = BTUSB_REALTEK |
747 BTUSB_WIDEBAND_SPEECH },
748 { USB_DEVICE(0x1358, 0xc123), .driver_info = BTUSB_REALTEK |
749 BTUSB_WIDEBAND_SPEECH },
750 { USB_DEVICE(0x0bda, 0xc123), .driver_info = BTUSB_REALTEK |
751 BTUSB_WIDEBAND_SPEECH },
752 { USB_DEVICE(0x0cb5, 0xc547), .driver_info = BTUSB_REALTEK |
753 BTUSB_WIDEBAND_SPEECH },
754
755 /* Actions Semiconductor ATS2851 based devices */
756 { USB_DEVICE(0x10d7, 0xb012), .driver_info = BTUSB_ACTIONS_SEMI },
757
758 /* Silicon Wave based devices */
759 { USB_DEVICE(0x0c10, 0x0000), .driver_info = BTUSB_SWAVE },
760
761 { } /* Terminating entry */
762};
763
764/* The Bluetooth USB module build into some devices needs to be reset on resume,
765 * this is a problem with the platform (likely shutting off all power) not with
766 * the module itself. So we use a DMI list to match known broken platforms.
767 */
768static const struct dmi_system_id btusb_needs_reset_resume_table[] = {
769 {
770 /* Dell OptiPlex 3060 (QCA ROME device 0cf3:e007) */
771 .matches = {
772 DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
773 DMI_MATCH(DMI_PRODUCT_NAME, "OptiPlex 3060"),
774 },
775 },
776 {
777 /* Dell XPS 9360 (QCA ROME device 0cf3:e300) */
778 .matches = {
779 DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
780 DMI_MATCH(DMI_PRODUCT_NAME, "XPS 13 9360"),
781 },
782 },
783 {
784 /* Dell Inspiron 5565 (QCA ROME device 0cf3:e009) */
785 .matches = {
786 DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
787 DMI_MATCH(DMI_PRODUCT_NAME, "Inspiron 5565"),
788 },
789 },
790 {}
791};
792
793struct qca_dump_info {
794 /* fields for dump collection */
795 u16 id_vendor;
796 u16 id_product;
797 u32 fw_version;
798 u32 controller_id;
799 u32 ram_dump_size;
800 u16 ram_dump_seqno;
801};
802
803#define BTUSB_MAX_ISOC_FRAMES 10
804
805#define BTUSB_INTR_RUNNING 0
806#define BTUSB_BULK_RUNNING 1
807#define BTUSB_ISOC_RUNNING 2
808#define BTUSB_SUSPENDING 3
809#define BTUSB_DID_ISO_RESUME 4
810#define BTUSB_BOOTLOADER 5
811#define BTUSB_DOWNLOADING 6
812#define BTUSB_FIRMWARE_LOADED 7
813#define BTUSB_FIRMWARE_FAILED 8
814#define BTUSB_BOOTING 9
815#define BTUSB_DIAG_RUNNING 10
816#define BTUSB_OOB_WAKE_ENABLED 11
817#define BTUSB_HW_RESET_ACTIVE 12
818#define BTUSB_TX_WAIT_VND_EVT 13
819#define BTUSB_WAKEUP_AUTOSUSPEND 14
820#define BTUSB_USE_ALT3_FOR_WBS 15
821#define BTUSB_ALT6_CONTINUOUS_TX 16
822#define BTUSB_HW_SSR_ACTIVE 17
823
824struct btusb_data {
825 struct hci_dev *hdev;
826 struct usb_device *udev;
827 struct usb_interface *intf;
828 struct usb_interface *isoc;
829 struct usb_interface *diag;
830 unsigned isoc_ifnum;
831
832 unsigned long flags;
833
834 bool poll_sync;
835 int intr_interval;
836 struct work_struct work;
837 struct work_struct waker;
838 struct delayed_work rx_work;
839
840 struct sk_buff_head acl_q;
841
842 struct usb_anchor deferred;
843 struct usb_anchor tx_anchor;
844 int tx_in_flight;
845 spinlock_t txlock;
846
847 struct usb_anchor intr_anchor;
848 struct usb_anchor bulk_anchor;
849 struct usb_anchor isoc_anchor;
850 struct usb_anchor diag_anchor;
851 struct usb_anchor ctrl_anchor;
852 spinlock_t rxlock;
853
854 struct sk_buff *evt_skb;
855 struct sk_buff *acl_skb;
856 struct sk_buff *sco_skb;
857
858 struct usb_endpoint_descriptor *intr_ep;
859 struct usb_endpoint_descriptor *bulk_tx_ep;
860 struct usb_endpoint_descriptor *bulk_rx_ep;
861 struct usb_endpoint_descriptor *isoc_tx_ep;
862 struct usb_endpoint_descriptor *isoc_rx_ep;
863 struct usb_endpoint_descriptor *diag_tx_ep;
864 struct usb_endpoint_descriptor *diag_rx_ep;
865
866 struct gpio_desc *reset_gpio;
867
868 __u8 cmdreq_type;
869 __u8 cmdreq;
870
871 unsigned int sco_num;
872 unsigned int air_mode;
873 bool usb_alt6_packet_flow;
874 int isoc_altsetting;
875 int suspend_count;
876
877 int (*recv_event)(struct hci_dev *hdev, struct sk_buff *skb);
878 int (*recv_acl)(struct hci_dev *hdev, struct sk_buff *skb);
879 int (*recv_bulk)(struct btusb_data *data, void *buffer, int count);
880
881 int (*setup_on_usb)(struct hci_dev *hdev);
882
883 int (*suspend)(struct hci_dev *hdev);
884 int (*resume)(struct hci_dev *hdev);
885 int (*disconnect)(struct hci_dev *hdev);
886
887 int oob_wake_irq; /* irq for out-of-band wake-on-bt */
888 unsigned cmd_timeout_cnt;
889
890 struct qca_dump_info qca_dump;
891};
892
893static void btusb_reset(struct hci_dev *hdev)
894{
895 struct btusb_data *data;
896 int err;
897
898 if (hdev->reset) {
899 hdev->reset(hdev);
900 return;
901 }
902
903 data = hci_get_drvdata(hdev);
904 /* This is not an unbalanced PM reference since the device will reset */
905 err = usb_autopm_get_interface(data->intf);
906 if (err) {
907 bt_dev_err(hdev, "Failed usb_autopm_get_interface: %d", err);
908 return;
909 }
910
911 bt_dev_err(hdev, "Resetting usb device.");
912 usb_queue_reset_device(data->intf);
913}
914
915static void btusb_intel_cmd_timeout(struct hci_dev *hdev)
916{
917 struct btusb_data *data = hci_get_drvdata(hdev);
918 struct gpio_desc *reset_gpio = data->reset_gpio;
919 struct btintel_data *intel_data = hci_get_priv(hdev);
920
921 if (++data->cmd_timeout_cnt < 5)
922 return;
923
924 if (intel_data->acpi_reset_method) {
925 if (test_and_set_bit(INTEL_ACPI_RESET_ACTIVE, intel_data->flags)) {
926 bt_dev_err(hdev, "acpi: last reset failed ? Not resetting again");
927 return;
928 }
929
930 bt_dev_err(hdev, "Initiating acpi reset method");
931 /* If ACPI reset method fails, lets try with legacy GPIO
932 * toggling
933 */
934 if (!intel_data->acpi_reset_method(hdev)) {
935 return;
936 }
937 }
938
939 if (!reset_gpio) {
940 btusb_reset(hdev);
941 return;
942 }
943
944 /*
945 * Toggle the hard reset line if the platform provides one. The reset
946 * is going to yank the device off the USB and then replug. So doing
947 * once is enough. The cleanup is handled correctly on the way out
948 * (standard USB disconnect), and the new device is detected cleanly
949 * and bound to the driver again like it should be.
950 */
951 if (test_and_set_bit(BTUSB_HW_RESET_ACTIVE, &data->flags)) {
952 bt_dev_err(hdev, "last reset failed? Not resetting again");
953 return;
954 }
955
956 bt_dev_err(hdev, "Initiating HW reset via gpio");
957 gpiod_set_value_cansleep(reset_gpio, 1);
958 msleep(100);
959 gpiod_set_value_cansleep(reset_gpio, 0);
960}
961
962#define RTK_DEVCOREDUMP_CODE_MEMDUMP 0x01
963#define RTK_DEVCOREDUMP_CODE_HW_ERR 0x02
964#define RTK_DEVCOREDUMP_CODE_CMD_TIMEOUT 0x03
965
966#define RTK_SUB_EVENT_CODE_COREDUMP 0x34
967
968struct rtk_dev_coredump_hdr {
969 u8 type;
970 u8 code;
971 u8 reserved[2];
972} __packed;
973
974static inline void btusb_rtl_alloc_devcoredump(struct hci_dev *hdev,
975 struct rtk_dev_coredump_hdr *hdr, u8 *buf, u32 len)
976{
977 struct sk_buff *skb;
978
979 skb = alloc_skb(len + sizeof(*hdr), GFP_ATOMIC);
980 if (!skb)
981 return;
982
983 skb_put_data(skb, hdr, sizeof(*hdr));
984 if (len)
985 skb_put_data(skb, buf, len);
986
987 if (!hci_devcd_init(hdev, skb->len)) {
988 hci_devcd_append(hdev, skb);
989 hci_devcd_complete(hdev);
990 } else {
991 bt_dev_err(hdev, "RTL: Failed to generate devcoredump");
992 kfree_skb(skb);
993 }
994}
995
996static void btusb_rtl_cmd_timeout(struct hci_dev *hdev)
997{
998 struct btusb_data *data = hci_get_drvdata(hdev);
999 struct gpio_desc *reset_gpio = data->reset_gpio;
1000 struct rtk_dev_coredump_hdr hdr = {
1001 .type = RTK_DEVCOREDUMP_CODE_CMD_TIMEOUT,
1002 };
1003
1004 btusb_rtl_alloc_devcoredump(hdev, &hdr, NULL, 0);
1005
1006 if (++data->cmd_timeout_cnt < 5)
1007 return;
1008
1009 if (!reset_gpio) {
1010 btusb_reset(hdev);
1011 return;
1012 }
1013
1014 /* Toggle the hard reset line. The Realtek device is going to
1015 * yank itself off the USB and then replug. The cleanup is handled
1016 * correctly on the way out (standard USB disconnect), and the new
1017 * device is detected cleanly and bound to the driver again like
1018 * it should be.
1019 */
1020 if (test_and_set_bit(BTUSB_HW_RESET_ACTIVE, &data->flags)) {
1021 bt_dev_err(hdev, "last reset failed? Not resetting again");
1022 return;
1023 }
1024
1025 bt_dev_err(hdev, "Reset Realtek device via gpio");
1026 gpiod_set_value_cansleep(reset_gpio, 1);
1027 msleep(200);
1028 gpiod_set_value_cansleep(reset_gpio, 0);
1029}
1030
1031static void btusb_rtl_hw_error(struct hci_dev *hdev, u8 code)
1032{
1033 struct rtk_dev_coredump_hdr hdr = {
1034 .type = RTK_DEVCOREDUMP_CODE_HW_ERR,
1035 .code = code,
1036 };
1037
1038 bt_dev_err(hdev, "RTL: hw err, trigger devcoredump (%d)", code);
1039
1040 btusb_rtl_alloc_devcoredump(hdev, &hdr, NULL, 0);
1041}
1042
1043static void btusb_qca_cmd_timeout(struct hci_dev *hdev)
1044{
1045 struct btusb_data *data = hci_get_drvdata(hdev);
1046 struct gpio_desc *reset_gpio = data->reset_gpio;
1047
1048 if (test_bit(BTUSB_HW_SSR_ACTIVE, &data->flags)) {
1049 bt_dev_info(hdev, "Ramdump in progress, defer cmd_timeout");
1050 return;
1051 }
1052
1053 if (++data->cmd_timeout_cnt < 5)
1054 return;
1055
1056 if (reset_gpio) {
1057 bt_dev_err(hdev, "Reset qca device via bt_en gpio");
1058
1059 /* Toggle the hard reset line. The qca bt device is going to
1060 * yank itself off the USB and then replug. The cleanup is handled
1061 * correctly on the way out (standard USB disconnect), and the new
1062 * device is detected cleanly and bound to the driver again like
1063 * it should be.
1064 */
1065 if (test_and_set_bit(BTUSB_HW_RESET_ACTIVE, &data->flags)) {
1066 bt_dev_err(hdev, "last reset failed? Not resetting again");
1067 return;
1068 }
1069
1070 gpiod_set_value_cansleep(reset_gpio, 0);
1071 msleep(200);
1072 gpiod_set_value_cansleep(reset_gpio, 1);
1073
1074 return;
1075 }
1076
1077 btusb_reset(hdev);
1078}
1079
1080static inline void btusb_free_frags(struct btusb_data *data)
1081{
1082 unsigned long flags;
1083
1084 spin_lock_irqsave(&data->rxlock, flags);
1085
1086 dev_kfree_skb_irq(data->evt_skb);
1087 data->evt_skb = NULL;
1088
1089 dev_kfree_skb_irq(data->acl_skb);
1090 data->acl_skb = NULL;
1091
1092 dev_kfree_skb_irq(data->sco_skb);
1093 data->sco_skb = NULL;
1094
1095 spin_unlock_irqrestore(&data->rxlock, flags);
1096}
1097
1098static int btusb_recv_event(struct btusb_data *data, struct sk_buff *skb)
1099{
1100 if (data->intr_interval) {
1101 /* Trigger dequeue immediately if an event is received */
1102 schedule_delayed_work(&data->rx_work, 0);
1103 }
1104
1105 return data->recv_event(data->hdev, skb);
1106}
1107
1108static int btusb_recv_intr(struct btusb_data *data, void *buffer, int count)
1109{
1110 struct sk_buff *skb;
1111 unsigned long flags;
1112 int err = 0;
1113
1114 spin_lock_irqsave(&data->rxlock, flags);
1115 skb = data->evt_skb;
1116
1117 while (count) {
1118 int len;
1119
1120 if (!skb) {
1121 skb = bt_skb_alloc(HCI_MAX_EVENT_SIZE, GFP_ATOMIC);
1122 if (!skb) {
1123 err = -ENOMEM;
1124 break;
1125 }
1126
1127 hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
1128 hci_skb_expect(skb) = HCI_EVENT_HDR_SIZE;
1129 }
1130
1131 len = min_t(uint, hci_skb_expect(skb), count);
1132 skb_put_data(skb, buffer, len);
1133
1134 count -= len;
1135 buffer += len;
1136 hci_skb_expect(skb) -= len;
1137
1138 if (skb->len == HCI_EVENT_HDR_SIZE) {
1139 /* Complete event header */
1140 hci_skb_expect(skb) = hci_event_hdr(skb)->plen;
1141
1142 if (skb_tailroom(skb) < hci_skb_expect(skb)) {
1143 kfree_skb(skb);
1144 skb = NULL;
1145
1146 err = -EILSEQ;
1147 break;
1148 }
1149 }
1150
1151 if (!hci_skb_expect(skb)) {
1152 /* Complete frame */
1153 btusb_recv_event(data, skb);
1154 skb = NULL;
1155 }
1156 }
1157
1158 data->evt_skb = skb;
1159 spin_unlock_irqrestore(&data->rxlock, flags);
1160
1161 return err;
1162}
1163
1164static int btusb_recv_acl(struct btusb_data *data, struct sk_buff *skb)
1165{
1166 /* Only queue ACL packet if intr_interval is set as it means
1167 * force_poll_sync has been enabled.
1168 */
1169 if (!data->intr_interval)
1170 return data->recv_acl(data->hdev, skb);
1171
1172 skb_queue_tail(&data->acl_q, skb);
1173 schedule_delayed_work(&data->rx_work, data->intr_interval);
1174
1175 return 0;
1176}
1177
1178static int btusb_recv_bulk(struct btusb_data *data, void *buffer, int count)
1179{
1180 struct sk_buff *skb;
1181 unsigned long flags;
1182 int err = 0;
1183
1184 spin_lock_irqsave(&data->rxlock, flags);
1185 skb = data->acl_skb;
1186
1187 while (count) {
1188 int len;
1189
1190 if (!skb) {
1191 skb = bt_skb_alloc(HCI_MAX_FRAME_SIZE, GFP_ATOMIC);
1192 if (!skb) {
1193 err = -ENOMEM;
1194 break;
1195 }
1196
1197 hci_skb_pkt_type(skb) = HCI_ACLDATA_PKT;
1198 hci_skb_expect(skb) = HCI_ACL_HDR_SIZE;
1199 }
1200
1201 len = min_t(uint, hci_skb_expect(skb), count);
1202 skb_put_data(skb, buffer, len);
1203
1204 count -= len;
1205 buffer += len;
1206 hci_skb_expect(skb) -= len;
1207
1208 if (skb->len == HCI_ACL_HDR_SIZE) {
1209 __le16 dlen = hci_acl_hdr(skb)->dlen;
1210
1211 /* Complete ACL header */
1212 hci_skb_expect(skb) = __le16_to_cpu(dlen);
1213
1214 if (skb_tailroom(skb) < hci_skb_expect(skb)) {
1215 kfree_skb(skb);
1216 skb = NULL;
1217
1218 err = -EILSEQ;
1219 break;
1220 }
1221 }
1222
1223 if (!hci_skb_expect(skb)) {
1224 /* Complete frame */
1225 btusb_recv_acl(data, skb);
1226 skb = NULL;
1227 }
1228 }
1229
1230 data->acl_skb = skb;
1231 spin_unlock_irqrestore(&data->rxlock, flags);
1232
1233 return err;
1234}
1235
1236static bool btusb_validate_sco_handle(struct hci_dev *hdev,
1237 struct hci_sco_hdr *hdr)
1238{
1239 __u16 handle;
1240
1241 if (hci_dev_test_flag(hdev, HCI_USER_CHANNEL))
1242 // Can't validate, userspace controls everything.
1243 return true;
1244
1245 /*
1246 * USB isochronous transfers are not designed to be reliable and may
1247 * lose fragments. When this happens, the next first fragment
1248 * encountered might actually be a continuation fragment.
1249 * Validate the handle to detect it and drop it, or else the upper
1250 * layer will get garbage for a while.
1251 */
1252
1253 handle = hci_handle(__le16_to_cpu(hdr->handle));
1254
1255 switch (hci_conn_lookup_type(hdev, handle)) {
1256 case SCO_LINK:
1257 case ESCO_LINK:
1258 return true;
1259 default:
1260 return false;
1261 }
1262}
1263
1264static int btusb_recv_isoc(struct btusb_data *data, void *buffer, int count)
1265{
1266 struct sk_buff *skb;
1267 unsigned long flags;
1268 int err = 0;
1269
1270 spin_lock_irqsave(&data->rxlock, flags);
1271 skb = data->sco_skb;
1272
1273 while (count) {
1274 int len;
1275
1276 if (!skb) {
1277 skb = bt_skb_alloc(HCI_MAX_SCO_SIZE, GFP_ATOMIC);
1278 if (!skb) {
1279 err = -ENOMEM;
1280 break;
1281 }
1282
1283 hci_skb_pkt_type(skb) = HCI_SCODATA_PKT;
1284 hci_skb_expect(skb) = HCI_SCO_HDR_SIZE;
1285 }
1286
1287 len = min_t(uint, hci_skb_expect(skb), count);
1288 skb_put_data(skb, buffer, len);
1289
1290 count -= len;
1291 buffer += len;
1292 hci_skb_expect(skb) -= len;
1293
1294 if (skb->len == HCI_SCO_HDR_SIZE) {
1295 /* Complete SCO header */
1296 struct hci_sco_hdr *hdr = hci_sco_hdr(skb);
1297
1298 hci_skb_expect(skb) = hdr->dlen;
1299
1300 if (skb_tailroom(skb) < hci_skb_expect(skb) ||
1301 !btusb_validate_sco_handle(data->hdev, hdr)) {
1302 kfree_skb(skb);
1303 skb = NULL;
1304
1305 err = -EILSEQ;
1306 break;
1307 }
1308 }
1309
1310 if (!hci_skb_expect(skb)) {
1311 /* Complete frame */
1312 hci_recv_frame(data->hdev, skb);
1313 skb = NULL;
1314 }
1315 }
1316
1317 data->sco_skb = skb;
1318 spin_unlock_irqrestore(&data->rxlock, flags);
1319
1320 return err;
1321}
1322
1323static void btusb_intr_complete(struct urb *urb)
1324{
1325 struct hci_dev *hdev = urb->context;
1326 struct btusb_data *data = hci_get_drvdata(hdev);
1327 int err;
1328
1329 BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
1330 urb->actual_length);
1331
1332 if (!test_bit(HCI_RUNNING, &hdev->flags))
1333 return;
1334
1335 if (urb->status == 0) {
1336 hdev->stat.byte_rx += urb->actual_length;
1337
1338 if (btusb_recv_intr(data, urb->transfer_buffer,
1339 urb->actual_length) < 0) {
1340 bt_dev_err(hdev, "corrupted event packet");
1341 hdev->stat.err_rx++;
1342 }
1343 } else if (urb->status == -ENOENT) {
1344 /* Avoid suspend failed when usb_kill_urb */
1345 return;
1346 }
1347
1348 if (!test_bit(BTUSB_INTR_RUNNING, &data->flags))
1349 return;
1350
1351 usb_mark_last_busy(data->udev);
1352 usb_anchor_urb(urb, &data->intr_anchor);
1353
1354 err = usb_submit_urb(urb, GFP_ATOMIC);
1355 if (err < 0) {
1356 /* -EPERM: urb is being killed;
1357 * -ENODEV: device got disconnected
1358 */
1359 if (err != -EPERM && err != -ENODEV)
1360 bt_dev_err(hdev, "urb %p failed to resubmit (%d)",
1361 urb, -err);
1362 if (err != -EPERM)
1363 hci_cmd_sync_cancel(hdev, -err);
1364 usb_unanchor_urb(urb);
1365 }
1366}
1367
1368static int btusb_submit_intr_urb(struct hci_dev *hdev, gfp_t mem_flags)
1369{
1370 struct btusb_data *data = hci_get_drvdata(hdev);
1371 struct urb *urb;
1372 unsigned char *buf;
1373 unsigned int pipe;
1374 int err, size;
1375
1376 BT_DBG("%s", hdev->name);
1377
1378 if (!data->intr_ep)
1379 return -ENODEV;
1380
1381 urb = usb_alloc_urb(0, mem_flags);
1382 if (!urb)
1383 return -ENOMEM;
1384
1385 if (le16_to_cpu(data->udev->descriptor.idVendor) == 0x0a12 &&
1386 le16_to_cpu(data->udev->descriptor.idProduct) == 0x0001)
1387 /* Fake CSR devices don't seem to support sort-transter */
1388 size = le16_to_cpu(data->intr_ep->wMaxPacketSize);
1389 else
1390 /* Use maximum HCI Event size so the USB stack handles
1391 * ZPL/short-transfer automatically.
1392 */
1393 size = HCI_MAX_EVENT_SIZE;
1394
1395 buf = kmalloc(size, mem_flags);
1396 if (!buf) {
1397 usb_free_urb(urb);
1398 return -ENOMEM;
1399 }
1400
1401 pipe = usb_rcvintpipe(data->udev, data->intr_ep->bEndpointAddress);
1402
1403 usb_fill_int_urb(urb, data->udev, pipe, buf, size,
1404 btusb_intr_complete, hdev, data->intr_ep->bInterval);
1405
1406 urb->transfer_flags |= URB_FREE_BUFFER;
1407
1408 usb_anchor_urb(urb, &data->intr_anchor);
1409
1410 err = usb_submit_urb(urb, mem_flags);
1411 if (err < 0) {
1412 if (err != -EPERM && err != -ENODEV)
1413 bt_dev_err(hdev, "urb %p submission failed (%d)",
1414 urb, -err);
1415 if (err != -EPERM)
1416 hci_cmd_sync_cancel(hdev, -err);
1417 usb_unanchor_urb(urb);
1418 }
1419
1420 /* Only initialize intr_interval if URB poll sync is enabled */
1421 if (!data->poll_sync)
1422 goto done;
1423
1424 /* The units are frames (milliseconds) for full and low speed devices,
1425 * and microframes (1/8 millisecond) for highspeed and SuperSpeed
1426 * devices.
1427 *
1428 * This is done once on open/resume so it shouldn't change even if
1429 * force_poll_sync changes.
1430 */
1431 switch (urb->dev->speed) {
1432 case USB_SPEED_SUPER_PLUS:
1433 case USB_SPEED_SUPER: /* units are 125us */
1434 data->intr_interval = usecs_to_jiffies(urb->interval * 125);
1435 break;
1436 default:
1437 data->intr_interval = msecs_to_jiffies(urb->interval);
1438 break;
1439 }
1440
1441done:
1442 usb_free_urb(urb);
1443
1444 return err;
1445}
1446
1447static void btusb_bulk_complete(struct urb *urb)
1448{
1449 struct hci_dev *hdev = urb->context;
1450 struct btusb_data *data = hci_get_drvdata(hdev);
1451 int err;
1452
1453 BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
1454 urb->actual_length);
1455
1456 if (!test_bit(HCI_RUNNING, &hdev->flags))
1457 return;
1458
1459 if (urb->status == 0) {
1460 hdev->stat.byte_rx += urb->actual_length;
1461
1462 if (data->recv_bulk(data, urb->transfer_buffer,
1463 urb->actual_length) < 0) {
1464 bt_dev_err(hdev, "corrupted ACL packet");
1465 hdev->stat.err_rx++;
1466 }
1467 } else if (urb->status == -ENOENT) {
1468 /* Avoid suspend failed when usb_kill_urb */
1469 return;
1470 }
1471
1472 if (!test_bit(BTUSB_BULK_RUNNING, &data->flags))
1473 return;
1474
1475 usb_anchor_urb(urb, &data->bulk_anchor);
1476 usb_mark_last_busy(data->udev);
1477
1478 err = usb_submit_urb(urb, GFP_ATOMIC);
1479 if (err < 0) {
1480 /* -EPERM: urb is being killed;
1481 * -ENODEV: device got disconnected
1482 */
1483 if (err != -EPERM && err != -ENODEV)
1484 bt_dev_err(hdev, "urb %p failed to resubmit (%d)",
1485 urb, -err);
1486 usb_unanchor_urb(urb);
1487 }
1488}
1489
1490static int btusb_submit_bulk_urb(struct hci_dev *hdev, gfp_t mem_flags)
1491{
1492 struct btusb_data *data = hci_get_drvdata(hdev);
1493 struct urb *urb;
1494 unsigned char *buf;
1495 unsigned int pipe;
1496 int err, size = HCI_MAX_FRAME_SIZE;
1497
1498 BT_DBG("%s", hdev->name);
1499
1500 if (!data->bulk_rx_ep)
1501 return -ENODEV;
1502
1503 urb = usb_alloc_urb(0, mem_flags);
1504 if (!urb)
1505 return -ENOMEM;
1506
1507 buf = kmalloc(size, mem_flags);
1508 if (!buf) {
1509 usb_free_urb(urb);
1510 return -ENOMEM;
1511 }
1512
1513 pipe = usb_rcvbulkpipe(data->udev, data->bulk_rx_ep->bEndpointAddress);
1514
1515 usb_fill_bulk_urb(urb, data->udev, pipe, buf, size,
1516 btusb_bulk_complete, hdev);
1517
1518 urb->transfer_flags |= URB_FREE_BUFFER;
1519
1520 usb_mark_last_busy(data->udev);
1521 usb_anchor_urb(urb, &data->bulk_anchor);
1522
1523 err = usb_submit_urb(urb, mem_flags);
1524 if (err < 0) {
1525 if (err != -EPERM && err != -ENODEV)
1526 bt_dev_err(hdev, "urb %p submission failed (%d)",
1527 urb, -err);
1528 usb_unanchor_urb(urb);
1529 }
1530
1531 usb_free_urb(urb);
1532
1533 return err;
1534}
1535
1536static void btusb_isoc_complete(struct urb *urb)
1537{
1538 struct hci_dev *hdev = urb->context;
1539 struct btusb_data *data = hci_get_drvdata(hdev);
1540 int i, err;
1541
1542 BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
1543 urb->actual_length);
1544
1545 if (!test_bit(HCI_RUNNING, &hdev->flags))
1546 return;
1547
1548 if (urb->status == 0) {
1549 for (i = 0; i < urb->number_of_packets; i++) {
1550 unsigned int offset = urb->iso_frame_desc[i].offset;
1551 unsigned int length = urb->iso_frame_desc[i].actual_length;
1552
1553 if (urb->iso_frame_desc[i].status)
1554 continue;
1555
1556 hdev->stat.byte_rx += length;
1557
1558 if (btusb_recv_isoc(data, urb->transfer_buffer + offset,
1559 length) < 0) {
1560 bt_dev_err(hdev, "corrupted SCO packet");
1561 hdev->stat.err_rx++;
1562 }
1563 }
1564 } else if (urb->status == -ENOENT) {
1565 /* Avoid suspend failed when usb_kill_urb */
1566 return;
1567 }
1568
1569 if (!test_bit(BTUSB_ISOC_RUNNING, &data->flags))
1570 return;
1571
1572 usb_anchor_urb(urb, &data->isoc_anchor);
1573
1574 err = usb_submit_urb(urb, GFP_ATOMIC);
1575 if (err < 0) {
1576 /* -EPERM: urb is being killed;
1577 * -ENODEV: device got disconnected
1578 */
1579 if (err != -EPERM && err != -ENODEV)
1580 bt_dev_err(hdev, "urb %p failed to resubmit (%d)",
1581 urb, -err);
1582 usb_unanchor_urb(urb);
1583 }
1584}
1585
1586static inline void __fill_isoc_descriptor_msbc(struct urb *urb, int len,
1587 int mtu, struct btusb_data *data)
1588{
1589 int i = 0, offset = 0;
1590 unsigned int interval;
1591
1592 BT_DBG("len %d mtu %d", len, mtu);
1593
1594 /* For mSBC ALT 6 settings some chips need to transmit the data
1595 * continuously without the zero length of USB packets.
1596 */
1597 if (test_bit(BTUSB_ALT6_CONTINUOUS_TX, &data->flags))
1598 goto ignore_usb_alt6_packet_flow;
1599
1600 /* For mSBC ALT 6 setting the host will send the packet at continuous
1601 * flow. As per core spec 5, vol 4, part B, table 2.1. For ALT setting
1602 * 6 the HCI PACKET INTERVAL should be 7.5ms for every usb packets.
1603 * To maintain the rate we send 63bytes of usb packets alternatively for
1604 * 7ms and 8ms to maintain the rate as 7.5ms.
1605 */
1606 if (data->usb_alt6_packet_flow) {
1607 interval = 7;
1608 data->usb_alt6_packet_flow = false;
1609 } else {
1610 interval = 6;
1611 data->usb_alt6_packet_flow = true;
1612 }
1613
1614 for (i = 0; i < interval; i++) {
1615 urb->iso_frame_desc[i].offset = offset;
1616 urb->iso_frame_desc[i].length = offset;
1617 }
1618
1619ignore_usb_alt6_packet_flow:
1620 if (len && i < BTUSB_MAX_ISOC_FRAMES) {
1621 urb->iso_frame_desc[i].offset = offset;
1622 urb->iso_frame_desc[i].length = len;
1623 i++;
1624 }
1625
1626 urb->number_of_packets = i;
1627}
1628
1629static inline void __fill_isoc_descriptor(struct urb *urb, int len, int mtu)
1630{
1631 int i, offset = 0;
1632
1633 BT_DBG("len %d mtu %d", len, mtu);
1634
1635 for (i = 0; i < BTUSB_MAX_ISOC_FRAMES && len >= mtu;
1636 i++, offset += mtu, len -= mtu) {
1637 urb->iso_frame_desc[i].offset = offset;
1638 urb->iso_frame_desc[i].length = mtu;
1639 }
1640
1641 if (len && i < BTUSB_MAX_ISOC_FRAMES) {
1642 urb->iso_frame_desc[i].offset = offset;
1643 urb->iso_frame_desc[i].length = len;
1644 i++;
1645 }
1646
1647 urb->number_of_packets = i;
1648}
1649
1650static int btusb_submit_isoc_urb(struct hci_dev *hdev, gfp_t mem_flags)
1651{
1652 struct btusb_data *data = hci_get_drvdata(hdev);
1653 struct urb *urb;
1654 unsigned char *buf;
1655 unsigned int pipe;
1656 int err, size;
1657
1658 BT_DBG("%s", hdev->name);
1659
1660 if (!data->isoc_rx_ep)
1661 return -ENODEV;
1662
1663 urb = usb_alloc_urb(BTUSB_MAX_ISOC_FRAMES, mem_flags);
1664 if (!urb)
1665 return -ENOMEM;
1666
1667 size = le16_to_cpu(data->isoc_rx_ep->wMaxPacketSize) *
1668 BTUSB_MAX_ISOC_FRAMES;
1669
1670 buf = kmalloc(size, mem_flags);
1671 if (!buf) {
1672 usb_free_urb(urb);
1673 return -ENOMEM;
1674 }
1675
1676 pipe = usb_rcvisocpipe(data->udev, data->isoc_rx_ep->bEndpointAddress);
1677
1678 usb_fill_int_urb(urb, data->udev, pipe, buf, size, btusb_isoc_complete,
1679 hdev, data->isoc_rx_ep->bInterval);
1680
1681 urb->transfer_flags = URB_FREE_BUFFER | URB_ISO_ASAP;
1682
1683 __fill_isoc_descriptor(urb, size,
1684 le16_to_cpu(data->isoc_rx_ep->wMaxPacketSize));
1685
1686 usb_anchor_urb(urb, &data->isoc_anchor);
1687
1688 err = usb_submit_urb(urb, mem_flags);
1689 if (err < 0) {
1690 if (err != -EPERM && err != -ENODEV)
1691 bt_dev_err(hdev, "urb %p submission failed (%d)",
1692 urb, -err);
1693 usb_unanchor_urb(urb);
1694 }
1695
1696 usb_free_urb(urb);
1697
1698 return err;
1699}
1700
1701static void btusb_diag_complete(struct urb *urb)
1702{
1703 struct hci_dev *hdev = urb->context;
1704 struct btusb_data *data = hci_get_drvdata(hdev);
1705 int err;
1706
1707 BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
1708 urb->actual_length);
1709
1710 if (urb->status == 0) {
1711 struct sk_buff *skb;
1712
1713 skb = bt_skb_alloc(urb->actual_length, GFP_ATOMIC);
1714 if (skb) {
1715 skb_put_data(skb, urb->transfer_buffer,
1716 urb->actual_length);
1717 hci_recv_diag(hdev, skb);
1718 }
1719 } else if (urb->status == -ENOENT) {
1720 /* Avoid suspend failed when usb_kill_urb */
1721 return;
1722 }
1723
1724 if (!test_bit(BTUSB_DIAG_RUNNING, &data->flags))
1725 return;
1726
1727 usb_anchor_urb(urb, &data->diag_anchor);
1728 usb_mark_last_busy(data->udev);
1729
1730 err = usb_submit_urb(urb, GFP_ATOMIC);
1731 if (err < 0) {
1732 /* -EPERM: urb is being killed;
1733 * -ENODEV: device got disconnected
1734 */
1735 if (err != -EPERM && err != -ENODEV)
1736 bt_dev_err(hdev, "urb %p failed to resubmit (%d)",
1737 urb, -err);
1738 usb_unanchor_urb(urb);
1739 }
1740}
1741
1742static int btusb_submit_diag_urb(struct hci_dev *hdev, gfp_t mem_flags)
1743{
1744 struct btusb_data *data = hci_get_drvdata(hdev);
1745 struct urb *urb;
1746 unsigned char *buf;
1747 unsigned int pipe;
1748 int err, size = HCI_MAX_FRAME_SIZE;
1749
1750 BT_DBG("%s", hdev->name);
1751
1752 if (!data->diag_rx_ep)
1753 return -ENODEV;
1754
1755 urb = usb_alloc_urb(0, mem_flags);
1756 if (!urb)
1757 return -ENOMEM;
1758
1759 buf = kmalloc(size, mem_flags);
1760 if (!buf) {
1761 usb_free_urb(urb);
1762 return -ENOMEM;
1763 }
1764
1765 pipe = usb_rcvbulkpipe(data->udev, data->diag_rx_ep->bEndpointAddress);
1766
1767 usb_fill_bulk_urb(urb, data->udev, pipe, buf, size,
1768 btusb_diag_complete, hdev);
1769
1770 urb->transfer_flags |= URB_FREE_BUFFER;
1771
1772 usb_mark_last_busy(data->udev);
1773 usb_anchor_urb(urb, &data->diag_anchor);
1774
1775 err = usb_submit_urb(urb, mem_flags);
1776 if (err < 0) {
1777 if (err != -EPERM && err != -ENODEV)
1778 bt_dev_err(hdev, "urb %p submission failed (%d)",
1779 urb, -err);
1780 usb_unanchor_urb(urb);
1781 }
1782
1783 usb_free_urb(urb);
1784
1785 return err;
1786}
1787
1788static void btusb_tx_complete(struct urb *urb)
1789{
1790 struct sk_buff *skb = urb->context;
1791 struct hci_dev *hdev = (struct hci_dev *)skb->dev;
1792 struct btusb_data *data = hci_get_drvdata(hdev);
1793 unsigned long flags;
1794
1795 BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
1796 urb->actual_length);
1797
1798 if (!test_bit(HCI_RUNNING, &hdev->flags))
1799 goto done;
1800
1801 if (!urb->status) {
1802 hdev->stat.byte_tx += urb->transfer_buffer_length;
1803 } else {
1804 if (hci_skb_pkt_type(skb) == HCI_COMMAND_PKT)
1805 hci_cmd_sync_cancel(hdev, -urb->status);
1806 hdev->stat.err_tx++;
1807 }
1808
1809done:
1810 spin_lock_irqsave(&data->txlock, flags);
1811 data->tx_in_flight--;
1812 spin_unlock_irqrestore(&data->txlock, flags);
1813
1814 kfree(urb->setup_packet);
1815
1816 kfree_skb(skb);
1817}
1818
1819static void btusb_isoc_tx_complete(struct urb *urb)
1820{
1821 struct sk_buff *skb = urb->context;
1822 struct hci_dev *hdev = (struct hci_dev *)skb->dev;
1823
1824 BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
1825 urb->actual_length);
1826
1827 if (!test_bit(HCI_RUNNING, &hdev->flags))
1828 goto done;
1829
1830 if (!urb->status)
1831 hdev->stat.byte_tx += urb->transfer_buffer_length;
1832 else
1833 hdev->stat.err_tx++;
1834
1835done:
1836 kfree(urb->setup_packet);
1837
1838 kfree_skb(skb);
1839}
1840
1841static int btusb_open(struct hci_dev *hdev)
1842{
1843 struct btusb_data *data = hci_get_drvdata(hdev);
1844 int err;
1845
1846 BT_DBG("%s", hdev->name);
1847
1848 err = usb_autopm_get_interface(data->intf);
1849 if (err < 0)
1850 return err;
1851
1852 /* Patching USB firmware files prior to starting any URBs of HCI path
1853 * It is more safe to use USB bulk channel for downloading USB patch
1854 */
1855 if (data->setup_on_usb) {
1856 err = data->setup_on_usb(hdev);
1857 if (err < 0)
1858 goto setup_fail;
1859 }
1860
1861 data->intf->needs_remote_wakeup = 1;
1862
1863 if (test_and_set_bit(BTUSB_INTR_RUNNING, &data->flags))
1864 goto done;
1865
1866 err = btusb_submit_intr_urb(hdev, GFP_KERNEL);
1867 if (err < 0)
1868 goto failed;
1869
1870 err = btusb_submit_bulk_urb(hdev, GFP_KERNEL);
1871 if (err < 0) {
1872 usb_kill_anchored_urbs(&data->intr_anchor);
1873 goto failed;
1874 }
1875
1876 set_bit(BTUSB_BULK_RUNNING, &data->flags);
1877 btusb_submit_bulk_urb(hdev, GFP_KERNEL);
1878
1879 if (data->diag) {
1880 if (!btusb_submit_diag_urb(hdev, GFP_KERNEL))
1881 set_bit(BTUSB_DIAG_RUNNING, &data->flags);
1882 }
1883
1884done:
1885 usb_autopm_put_interface(data->intf);
1886 return 0;
1887
1888failed:
1889 clear_bit(BTUSB_INTR_RUNNING, &data->flags);
1890setup_fail:
1891 usb_autopm_put_interface(data->intf);
1892 return err;
1893}
1894
1895static void btusb_stop_traffic(struct btusb_data *data)
1896{
1897 usb_kill_anchored_urbs(&data->intr_anchor);
1898 usb_kill_anchored_urbs(&data->bulk_anchor);
1899 usb_kill_anchored_urbs(&data->isoc_anchor);
1900 usb_kill_anchored_urbs(&data->diag_anchor);
1901 usb_kill_anchored_urbs(&data->ctrl_anchor);
1902}
1903
1904static int btusb_close(struct hci_dev *hdev)
1905{
1906 struct btusb_data *data = hci_get_drvdata(hdev);
1907 int err;
1908
1909 BT_DBG("%s", hdev->name);
1910
1911 cancel_delayed_work(&data->rx_work);
1912 cancel_work_sync(&data->work);
1913 cancel_work_sync(&data->waker);
1914
1915 skb_queue_purge(&data->acl_q);
1916
1917 clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
1918 clear_bit(BTUSB_BULK_RUNNING, &data->flags);
1919 clear_bit(BTUSB_INTR_RUNNING, &data->flags);
1920 clear_bit(BTUSB_DIAG_RUNNING, &data->flags);
1921
1922 btusb_stop_traffic(data);
1923 btusb_free_frags(data);
1924
1925 err = usb_autopm_get_interface(data->intf);
1926 if (err < 0)
1927 goto failed;
1928
1929 data->intf->needs_remote_wakeup = 0;
1930
1931 /* Enable remote wake up for auto-suspend */
1932 if (test_bit(BTUSB_WAKEUP_AUTOSUSPEND, &data->flags))
1933 data->intf->needs_remote_wakeup = 1;
1934
1935 usb_autopm_put_interface(data->intf);
1936
1937failed:
1938 usb_scuttle_anchored_urbs(&data->deferred);
1939 return 0;
1940}
1941
1942static int btusb_flush(struct hci_dev *hdev)
1943{
1944 struct btusb_data *data = hci_get_drvdata(hdev);
1945
1946 BT_DBG("%s", hdev->name);
1947
1948 cancel_delayed_work(&data->rx_work);
1949
1950 skb_queue_purge(&data->acl_q);
1951
1952 usb_kill_anchored_urbs(&data->tx_anchor);
1953 btusb_free_frags(data);
1954
1955 return 0;
1956}
1957
1958static struct urb *alloc_ctrl_urb(struct hci_dev *hdev, struct sk_buff *skb)
1959{
1960 struct btusb_data *data = hci_get_drvdata(hdev);
1961 struct usb_ctrlrequest *dr;
1962 struct urb *urb;
1963 unsigned int pipe;
1964
1965 urb = usb_alloc_urb(0, GFP_KERNEL);
1966 if (!urb)
1967 return ERR_PTR(-ENOMEM);
1968
1969 dr = kmalloc(sizeof(*dr), GFP_KERNEL);
1970 if (!dr) {
1971 usb_free_urb(urb);
1972 return ERR_PTR(-ENOMEM);
1973 }
1974
1975 dr->bRequestType = data->cmdreq_type;
1976 dr->bRequest = data->cmdreq;
1977 dr->wIndex = 0;
1978 dr->wValue = 0;
1979 dr->wLength = __cpu_to_le16(skb->len);
1980
1981 pipe = usb_sndctrlpipe(data->udev, 0x00);
1982
1983 usb_fill_control_urb(urb, data->udev, pipe, (void *)dr,
1984 skb->data, skb->len, btusb_tx_complete, skb);
1985
1986 skb->dev = (void *)hdev;
1987
1988 return urb;
1989}
1990
1991static struct urb *alloc_bulk_urb(struct hci_dev *hdev, struct sk_buff *skb)
1992{
1993 struct btusb_data *data = hci_get_drvdata(hdev);
1994 struct urb *urb;
1995 unsigned int pipe;
1996
1997 if (!data->bulk_tx_ep)
1998 return ERR_PTR(-ENODEV);
1999
2000 urb = usb_alloc_urb(0, GFP_KERNEL);
2001 if (!urb)
2002 return ERR_PTR(-ENOMEM);
2003
2004 pipe = usb_sndbulkpipe(data->udev, data->bulk_tx_ep->bEndpointAddress);
2005
2006 usb_fill_bulk_urb(urb, data->udev, pipe,
2007 skb->data, skb->len, btusb_tx_complete, skb);
2008
2009 skb->dev = (void *)hdev;
2010
2011 return urb;
2012}
2013
2014static struct urb *alloc_isoc_urb(struct hci_dev *hdev, struct sk_buff *skb)
2015{
2016 struct btusb_data *data = hci_get_drvdata(hdev);
2017 struct urb *urb;
2018 unsigned int pipe;
2019
2020 if (!data->isoc_tx_ep)
2021 return ERR_PTR(-ENODEV);
2022
2023 urb = usb_alloc_urb(BTUSB_MAX_ISOC_FRAMES, GFP_KERNEL);
2024 if (!urb)
2025 return ERR_PTR(-ENOMEM);
2026
2027 pipe = usb_sndisocpipe(data->udev, data->isoc_tx_ep->bEndpointAddress);
2028
2029 usb_fill_int_urb(urb, data->udev, pipe,
2030 skb->data, skb->len, btusb_isoc_tx_complete,
2031 skb, data->isoc_tx_ep->bInterval);
2032
2033 urb->transfer_flags = URB_ISO_ASAP;
2034
2035 if (data->isoc_altsetting == 6)
2036 __fill_isoc_descriptor_msbc(urb, skb->len,
2037 le16_to_cpu(data->isoc_tx_ep->wMaxPacketSize),
2038 data);
2039 else
2040 __fill_isoc_descriptor(urb, skb->len,
2041 le16_to_cpu(data->isoc_tx_ep->wMaxPacketSize));
2042 skb->dev = (void *)hdev;
2043
2044 return urb;
2045}
2046
2047static int submit_tx_urb(struct hci_dev *hdev, struct urb *urb)
2048{
2049 struct btusb_data *data = hci_get_drvdata(hdev);
2050 int err;
2051
2052 usb_anchor_urb(urb, &data->tx_anchor);
2053
2054 err = usb_submit_urb(urb, GFP_KERNEL);
2055 if (err < 0) {
2056 if (err != -EPERM && err != -ENODEV)
2057 bt_dev_err(hdev, "urb %p submission failed (%d)",
2058 urb, -err);
2059 kfree(urb->setup_packet);
2060 usb_unanchor_urb(urb);
2061 } else {
2062 usb_mark_last_busy(data->udev);
2063 }
2064
2065 usb_free_urb(urb);
2066 return err;
2067}
2068
2069static int submit_or_queue_tx_urb(struct hci_dev *hdev, struct urb *urb)
2070{
2071 struct btusb_data *data = hci_get_drvdata(hdev);
2072 unsigned long flags;
2073 bool suspending;
2074
2075 spin_lock_irqsave(&data->txlock, flags);
2076 suspending = test_bit(BTUSB_SUSPENDING, &data->flags);
2077 if (!suspending)
2078 data->tx_in_flight++;
2079 spin_unlock_irqrestore(&data->txlock, flags);
2080
2081 if (!suspending)
2082 return submit_tx_urb(hdev, urb);
2083
2084 usb_anchor_urb(urb, &data->deferred);
2085 schedule_work(&data->waker);
2086
2087 usb_free_urb(urb);
2088 return 0;
2089}
2090
2091static int btusb_send_frame(struct hci_dev *hdev, struct sk_buff *skb)
2092{
2093 struct urb *urb;
2094
2095 BT_DBG("%s", hdev->name);
2096
2097 switch (hci_skb_pkt_type(skb)) {
2098 case HCI_COMMAND_PKT:
2099 urb = alloc_ctrl_urb(hdev, skb);
2100 if (IS_ERR(urb))
2101 return PTR_ERR(urb);
2102
2103 hdev->stat.cmd_tx++;
2104 return submit_or_queue_tx_urb(hdev, urb);
2105
2106 case HCI_ACLDATA_PKT:
2107 urb = alloc_bulk_urb(hdev, skb);
2108 if (IS_ERR(urb))
2109 return PTR_ERR(urb);
2110
2111 hdev->stat.acl_tx++;
2112 return submit_or_queue_tx_urb(hdev, urb);
2113
2114 case HCI_SCODATA_PKT:
2115 if (hci_conn_num(hdev, SCO_LINK) < 1)
2116 return -ENODEV;
2117
2118 urb = alloc_isoc_urb(hdev, skb);
2119 if (IS_ERR(urb))
2120 return PTR_ERR(urb);
2121
2122 hdev->stat.sco_tx++;
2123 return submit_tx_urb(hdev, urb);
2124
2125 case HCI_ISODATA_PKT:
2126 urb = alloc_bulk_urb(hdev, skb);
2127 if (IS_ERR(urb))
2128 return PTR_ERR(urb);
2129
2130 return submit_or_queue_tx_urb(hdev, urb);
2131 }
2132
2133 return -EILSEQ;
2134}
2135
2136static void btusb_notify(struct hci_dev *hdev, unsigned int evt)
2137{
2138 struct btusb_data *data = hci_get_drvdata(hdev);
2139
2140 BT_DBG("%s evt %d", hdev->name, evt);
2141
2142 if (hci_conn_num(hdev, SCO_LINK) != data->sco_num) {
2143 data->sco_num = hci_conn_num(hdev, SCO_LINK);
2144 data->air_mode = evt;
2145 schedule_work(&data->work);
2146 }
2147}
2148
2149static inline int __set_isoc_interface(struct hci_dev *hdev, int altsetting)
2150{
2151 struct btusb_data *data = hci_get_drvdata(hdev);
2152 struct usb_interface *intf = data->isoc;
2153 struct usb_endpoint_descriptor *ep_desc;
2154 int i, err;
2155
2156 if (!data->isoc)
2157 return -ENODEV;
2158
2159 err = usb_set_interface(data->udev, data->isoc_ifnum, altsetting);
2160 if (err < 0) {
2161 bt_dev_err(hdev, "setting interface failed (%d)", -err);
2162 return err;
2163 }
2164
2165 data->isoc_altsetting = altsetting;
2166
2167 data->isoc_tx_ep = NULL;
2168 data->isoc_rx_ep = NULL;
2169
2170 for (i = 0; i < intf->cur_altsetting->desc.bNumEndpoints; i++) {
2171 ep_desc = &intf->cur_altsetting->endpoint[i].desc;
2172
2173 if (!data->isoc_tx_ep && usb_endpoint_is_isoc_out(ep_desc)) {
2174 data->isoc_tx_ep = ep_desc;
2175 continue;
2176 }
2177
2178 if (!data->isoc_rx_ep && usb_endpoint_is_isoc_in(ep_desc)) {
2179 data->isoc_rx_ep = ep_desc;
2180 continue;
2181 }
2182 }
2183
2184 if (!data->isoc_tx_ep || !data->isoc_rx_ep) {
2185 bt_dev_err(hdev, "invalid SCO descriptors");
2186 return -ENODEV;
2187 }
2188
2189 return 0;
2190}
2191
2192static int btusb_switch_alt_setting(struct hci_dev *hdev, int new_alts)
2193{
2194 struct btusb_data *data = hci_get_drvdata(hdev);
2195 int err;
2196
2197 if (data->isoc_altsetting != new_alts) {
2198 unsigned long flags;
2199
2200 clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
2201 usb_kill_anchored_urbs(&data->isoc_anchor);
2202
2203 /* When isochronous alternate setting needs to be
2204 * changed, because SCO connection has been added
2205 * or removed, a packet fragment may be left in the
2206 * reassembling state. This could lead to wrongly
2207 * assembled fragments.
2208 *
2209 * Clear outstanding fragment when selecting a new
2210 * alternate setting.
2211 */
2212 spin_lock_irqsave(&data->rxlock, flags);
2213 dev_kfree_skb_irq(data->sco_skb);
2214 data->sco_skb = NULL;
2215 spin_unlock_irqrestore(&data->rxlock, flags);
2216
2217 err = __set_isoc_interface(hdev, new_alts);
2218 if (err < 0)
2219 return err;
2220 }
2221
2222 if (!test_and_set_bit(BTUSB_ISOC_RUNNING, &data->flags)) {
2223 if (btusb_submit_isoc_urb(hdev, GFP_KERNEL) < 0)
2224 clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
2225 else
2226 btusb_submit_isoc_urb(hdev, GFP_KERNEL);
2227 }
2228
2229 return 0;
2230}
2231
2232static struct usb_host_interface *btusb_find_altsetting(struct btusb_data *data,
2233 int alt)
2234{
2235 struct usb_interface *intf = data->isoc;
2236 int i;
2237
2238 BT_DBG("Looking for Alt no :%d", alt);
2239
2240 if (!intf)
2241 return NULL;
2242
2243 for (i = 0; i < intf->num_altsetting; i++) {
2244 if (intf->altsetting[i].desc.bAlternateSetting == alt)
2245 return &intf->altsetting[i];
2246 }
2247
2248 return NULL;
2249}
2250
2251static void btusb_work(struct work_struct *work)
2252{
2253 struct btusb_data *data = container_of(work, struct btusb_data, work);
2254 struct hci_dev *hdev = data->hdev;
2255 int new_alts = 0;
2256 int err;
2257
2258 if (data->sco_num > 0) {
2259 if (!test_bit(BTUSB_DID_ISO_RESUME, &data->flags)) {
2260 err = usb_autopm_get_interface(data->isoc ? data->isoc : data->intf);
2261 if (err < 0) {
2262 clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
2263 usb_kill_anchored_urbs(&data->isoc_anchor);
2264 return;
2265 }
2266
2267 set_bit(BTUSB_DID_ISO_RESUME, &data->flags);
2268 }
2269
2270 if (data->air_mode == HCI_NOTIFY_ENABLE_SCO_CVSD) {
2271 if (hdev->voice_setting & 0x0020) {
2272 static const int alts[3] = { 2, 4, 5 };
2273
2274 new_alts = alts[data->sco_num - 1];
2275 } else {
2276 new_alts = data->sco_num;
2277 }
2278 } else if (data->air_mode == HCI_NOTIFY_ENABLE_SCO_TRANSP) {
2279 /* Bluetooth USB spec recommends alt 6 (63 bytes), but
2280 * many adapters do not support it. Alt 1 appears to
2281 * work for all adapters that do not have alt 6, and
2282 * which work with WBS at all. Some devices prefer
2283 * alt 3 (HCI payload >= 60 Bytes let air packet
2284 * data satisfy 60 bytes), requiring
2285 * MTU >= 3 (packets) * 25 (size) - 3 (headers) = 72
2286 * see also Core spec 5, vol 4, B 2.1.1 & Table 2.1.
2287 */
2288 if (btusb_find_altsetting(data, 6))
2289 new_alts = 6;
2290 else if (btusb_find_altsetting(data, 3) &&
2291 hdev->sco_mtu >= 72 &&
2292 test_bit(BTUSB_USE_ALT3_FOR_WBS, &data->flags))
2293 new_alts = 3;
2294 else
2295 new_alts = 1;
2296 }
2297
2298 if (btusb_switch_alt_setting(hdev, new_alts) < 0)
2299 bt_dev_err(hdev, "set USB alt:(%d) failed!", new_alts);
2300 } else {
2301 usb_kill_anchored_urbs(&data->isoc_anchor);
2302
2303 if (test_and_clear_bit(BTUSB_ISOC_RUNNING, &data->flags))
2304 __set_isoc_interface(hdev, 0);
2305
2306 if (test_and_clear_bit(BTUSB_DID_ISO_RESUME, &data->flags))
2307 usb_autopm_put_interface(data->isoc ? data->isoc : data->intf);
2308 }
2309}
2310
2311static void btusb_waker(struct work_struct *work)
2312{
2313 struct btusb_data *data = container_of(work, struct btusb_data, waker);
2314 int err;
2315
2316 err = usb_autopm_get_interface(data->intf);
2317 if (err < 0)
2318 return;
2319
2320 usb_autopm_put_interface(data->intf);
2321}
2322
2323static void btusb_rx_work(struct work_struct *work)
2324{
2325 struct btusb_data *data = container_of(work, struct btusb_data,
2326 rx_work.work);
2327 struct sk_buff *skb;
2328
2329 /* Dequeue ACL data received during the interval */
2330 while ((skb = skb_dequeue(&data->acl_q)))
2331 data->recv_acl(data->hdev, skb);
2332}
2333
2334static int btusb_setup_bcm92035(struct hci_dev *hdev)
2335{
2336 struct sk_buff *skb;
2337 u8 val = 0x00;
2338
2339 BT_DBG("%s", hdev->name);
2340
2341 skb = __hci_cmd_sync(hdev, 0xfc3b, 1, &val, HCI_INIT_TIMEOUT);
2342 if (IS_ERR(skb))
2343 bt_dev_err(hdev, "BCM92035 command failed (%ld)", PTR_ERR(skb));
2344 else
2345 kfree_skb(skb);
2346
2347 return 0;
2348}
2349
2350static int btusb_setup_csr(struct hci_dev *hdev)
2351{
2352 struct btusb_data *data = hci_get_drvdata(hdev);
2353 u16 bcdDevice = le16_to_cpu(data->udev->descriptor.bcdDevice);
2354 struct hci_rp_read_local_version *rp;
2355 struct sk_buff *skb;
2356 bool is_fake = false;
2357 int ret;
2358
2359 BT_DBG("%s", hdev->name);
2360
2361 skb = __hci_cmd_sync(hdev, HCI_OP_READ_LOCAL_VERSION, 0, NULL,
2362 HCI_INIT_TIMEOUT);
2363 if (IS_ERR(skb)) {
2364 int err = PTR_ERR(skb);
2365 bt_dev_err(hdev, "CSR: Local version failed (%d)", err);
2366 return err;
2367 }
2368
2369 rp = skb_pull_data(skb, sizeof(*rp));
2370 if (!rp) {
2371 bt_dev_err(hdev, "CSR: Local version length mismatch");
2372 kfree_skb(skb);
2373 return -EIO;
2374 }
2375
2376 bt_dev_info(hdev, "CSR: Setting up dongle with HCI ver=%u rev=%04x",
2377 rp->hci_ver, le16_to_cpu(rp->hci_rev));
2378
2379 bt_dev_info(hdev, "LMP ver=%u subver=%04x; manufacturer=%u",
2380 rp->lmp_ver, le16_to_cpu(rp->lmp_subver),
2381 le16_to_cpu(rp->manufacturer));
2382
2383 /* Detect a wide host of Chinese controllers that aren't CSR.
2384 *
2385 * Known fake bcdDevices: 0x0100, 0x0134, 0x1915, 0x2520, 0x7558, 0x8891
2386 *
2387 * The main thing they have in common is that these are really popular low-cost
2388 * options that support newer Bluetooth versions but rely on heavy VID/PID
2389 * squatting of this poor old Bluetooth 1.1 device. Even sold as such.
2390 *
2391 * We detect actual CSR devices by checking that the HCI manufacturer code
2392 * is Cambridge Silicon Radio (10) and ensuring that LMP sub-version and
2393 * HCI rev values always match. As they both store the firmware number.
2394 */
2395 if (le16_to_cpu(rp->manufacturer) != 10 ||
2396 le16_to_cpu(rp->hci_rev) != le16_to_cpu(rp->lmp_subver))
2397 is_fake = true;
2398
2399 /* Known legit CSR firmware build numbers and their supported BT versions:
2400 * - 1.1 (0x1) -> 0x0073, 0x020d, 0x033c, 0x034e
2401 * - 1.2 (0x2) -> 0x04d9, 0x0529
2402 * - 2.0 (0x3) -> 0x07a6, 0x07ad, 0x0c5c
2403 * - 2.1 (0x4) -> 0x149c, 0x1735, 0x1899 (0x1899 is a BlueCore4-External)
2404 * - 4.0 (0x6) -> 0x1d86, 0x2031, 0x22bb
2405 *
2406 * e.g. Real CSR dongles with LMP subversion 0x73 are old enough that
2407 * support BT 1.1 only; so it's a dead giveaway when some
2408 * third-party BT 4.0 dongle reuses it.
2409 */
2410 else if (le16_to_cpu(rp->lmp_subver) <= 0x034e &&
2411 rp->hci_ver > BLUETOOTH_VER_1_1)
2412 is_fake = true;
2413
2414 else if (le16_to_cpu(rp->lmp_subver) <= 0x0529 &&
2415 rp->hci_ver > BLUETOOTH_VER_1_2)
2416 is_fake = true;
2417
2418 else if (le16_to_cpu(rp->lmp_subver) <= 0x0c5c &&
2419 rp->hci_ver > BLUETOOTH_VER_2_0)
2420 is_fake = true;
2421
2422 else if (le16_to_cpu(rp->lmp_subver) <= 0x1899 &&
2423 rp->hci_ver > BLUETOOTH_VER_2_1)
2424 is_fake = true;
2425
2426 else if (le16_to_cpu(rp->lmp_subver) <= 0x22bb &&
2427 rp->hci_ver > BLUETOOTH_VER_4_0)
2428 is_fake = true;
2429
2430 /* Other clones which beat all the above checks */
2431 else if (bcdDevice == 0x0134 &&
2432 le16_to_cpu(rp->lmp_subver) == 0x0c5c &&
2433 rp->hci_ver == BLUETOOTH_VER_2_0)
2434 is_fake = true;
2435
2436 if (is_fake) {
2437 bt_dev_warn(hdev, "CSR: Unbranded CSR clone detected; adding workarounds and force-suspending once...");
2438
2439 /* Generally these clones have big discrepancies between
2440 * advertised features and what's actually supported.
2441 * Probably will need to be expanded in the future;
2442 * without these the controller will lock up.
2443 */
2444 set_bit(HCI_QUIRK_BROKEN_STORED_LINK_KEY, &hdev->quirks);
2445 set_bit(HCI_QUIRK_BROKEN_ERR_DATA_REPORTING, &hdev->quirks);
2446 set_bit(HCI_QUIRK_BROKEN_FILTER_CLEAR_ALL, &hdev->quirks);
2447 set_bit(HCI_QUIRK_NO_SUSPEND_NOTIFIER, &hdev->quirks);
2448
2449 /* Clear the reset quirk since this is not an actual
2450 * early Bluetooth 1.1 device from CSR.
2451 */
2452 clear_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
2453 clear_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
2454
2455 /*
2456 * Special workaround for these BT 4.0 chip clones, and potentially more:
2457 *
2458 * - 0x0134: a Barrot 8041a02 (HCI rev: 0x0810 sub: 0x1012)
2459 * - 0x7558: IC markings FR3191AHAL 749H15143 (HCI rev/sub-version: 0x0709)
2460 *
2461 * These controllers are really messed-up.
2462 *
2463 * 1. Their bulk RX endpoint will never report any data unless
2464 * the device was suspended at least once (yes, really).
2465 * 2. They will not wakeup when autosuspended and receiving data
2466 * on their bulk RX endpoint from e.g. a keyboard or mouse
2467 * (IOW remote-wakeup support is broken for the bulk endpoint).
2468 *
2469 * To fix 1. enable runtime-suspend, force-suspend the
2470 * HCI and then wake-it up by disabling runtime-suspend.
2471 *
2472 * To fix 2. clear the HCI's can_wake flag, this way the HCI
2473 * will still be autosuspended when it is not open.
2474 *
2475 * --
2476 *
2477 * Because these are widespread problems we prefer generic solutions; so
2478 * apply this initialization quirk to every controller that gets here,
2479 * it should be harmless. The alternative is to not work at all.
2480 */
2481 pm_runtime_allow(&data->udev->dev);
2482
2483 ret = pm_runtime_suspend(&data->udev->dev);
2484 if (ret >= 0)
2485 msleep(200);
2486 else
2487 bt_dev_warn(hdev, "CSR: Couldn't suspend the device for our Barrot 8041a02 receive-issue workaround");
2488
2489 pm_runtime_forbid(&data->udev->dev);
2490
2491 device_set_wakeup_capable(&data->udev->dev, false);
2492
2493 /* Re-enable autosuspend if this was requested */
2494 if (enable_autosuspend)
2495 usb_enable_autosuspend(data->udev);
2496 }
2497
2498 kfree_skb(skb);
2499
2500 return 0;
2501}
2502
2503static int inject_cmd_complete(struct hci_dev *hdev, __u16 opcode)
2504{
2505 struct sk_buff *skb;
2506 struct hci_event_hdr *hdr;
2507 struct hci_ev_cmd_complete *evt;
2508
2509 skb = bt_skb_alloc(sizeof(*hdr) + sizeof(*evt) + 1, GFP_KERNEL);
2510 if (!skb)
2511 return -ENOMEM;
2512
2513 hdr = skb_put(skb, sizeof(*hdr));
2514 hdr->evt = HCI_EV_CMD_COMPLETE;
2515 hdr->plen = sizeof(*evt) + 1;
2516
2517 evt = skb_put(skb, sizeof(*evt));
2518 evt->ncmd = 0x01;
2519 evt->opcode = cpu_to_le16(opcode);
2520
2521 skb_put_u8(skb, 0x00);
2522
2523 hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
2524
2525 return hci_recv_frame(hdev, skb);
2526}
2527
2528static int btusb_recv_bulk_intel(struct btusb_data *data, void *buffer,
2529 int count)
2530{
2531 struct hci_dev *hdev = data->hdev;
2532
2533 /* When the device is in bootloader mode, then it can send
2534 * events via the bulk endpoint. These events are treated the
2535 * same way as the ones received from the interrupt endpoint.
2536 */
2537 if (btintel_test_flag(hdev, INTEL_BOOTLOADER))
2538 return btusb_recv_intr(data, buffer, count);
2539
2540 return btusb_recv_bulk(data, buffer, count);
2541}
2542
2543static int btusb_send_frame_intel(struct hci_dev *hdev, struct sk_buff *skb)
2544{
2545 struct urb *urb;
2546
2547 BT_DBG("%s", hdev->name);
2548
2549 switch (hci_skb_pkt_type(skb)) {
2550 case HCI_COMMAND_PKT:
2551 if (btintel_test_flag(hdev, INTEL_BOOTLOADER)) {
2552 struct hci_command_hdr *cmd = (void *)skb->data;
2553 __u16 opcode = le16_to_cpu(cmd->opcode);
2554
2555 /* When in bootloader mode and the command 0xfc09
2556 * is received, it needs to be send down the
2557 * bulk endpoint. So allocate a bulk URB instead.
2558 */
2559 if (opcode == 0xfc09)
2560 urb = alloc_bulk_urb(hdev, skb);
2561 else
2562 urb = alloc_ctrl_urb(hdev, skb);
2563
2564 /* When the 0xfc01 command is issued to boot into
2565 * the operational firmware, it will actually not
2566 * send a command complete event. To keep the flow
2567 * control working inject that event here.
2568 */
2569 if (opcode == 0xfc01)
2570 inject_cmd_complete(hdev, opcode);
2571 } else {
2572 urb = alloc_ctrl_urb(hdev, skb);
2573 }
2574 if (IS_ERR(urb))
2575 return PTR_ERR(urb);
2576
2577 hdev->stat.cmd_tx++;
2578 return submit_or_queue_tx_urb(hdev, urb);
2579
2580 case HCI_ACLDATA_PKT:
2581 urb = alloc_bulk_urb(hdev, skb);
2582 if (IS_ERR(urb))
2583 return PTR_ERR(urb);
2584
2585 hdev->stat.acl_tx++;
2586 return submit_or_queue_tx_urb(hdev, urb);
2587
2588 case HCI_SCODATA_PKT:
2589 if (hci_conn_num(hdev, SCO_LINK) < 1)
2590 return -ENODEV;
2591
2592 urb = alloc_isoc_urb(hdev, skb);
2593 if (IS_ERR(urb))
2594 return PTR_ERR(urb);
2595
2596 hdev->stat.sco_tx++;
2597 return submit_tx_urb(hdev, urb);
2598
2599 case HCI_ISODATA_PKT:
2600 urb = alloc_bulk_urb(hdev, skb);
2601 if (IS_ERR(urb))
2602 return PTR_ERR(urb);
2603
2604 return submit_or_queue_tx_urb(hdev, urb);
2605 }
2606
2607 return -EILSEQ;
2608}
2609
2610static int btusb_setup_realtek(struct hci_dev *hdev)
2611{
2612 struct btusb_data *data = hci_get_drvdata(hdev);
2613 int ret;
2614
2615 ret = btrtl_setup_realtek(hdev);
2616
2617 if (btrealtek_test_flag(data->hdev, REALTEK_ALT6_CONTINUOUS_TX_CHIP))
2618 set_bit(BTUSB_ALT6_CONTINUOUS_TX, &data->flags);
2619
2620 return ret;
2621}
2622
2623static int btusb_recv_event_realtek(struct hci_dev *hdev, struct sk_buff *skb)
2624{
2625 if (skb->data[0] == HCI_VENDOR_PKT && skb->data[2] == RTK_SUB_EVENT_CODE_COREDUMP) {
2626 struct rtk_dev_coredump_hdr hdr = {
2627 .code = RTK_DEVCOREDUMP_CODE_MEMDUMP,
2628 };
2629
2630 bt_dev_dbg(hdev, "RTL: received coredump vendor evt, len %u",
2631 skb->len);
2632
2633 btusb_rtl_alloc_devcoredump(hdev, &hdr, skb->data, skb->len);
2634 kfree_skb(skb);
2635
2636 return 0;
2637 }
2638
2639 return hci_recv_frame(hdev, skb);
2640}
2641
2642static void btusb_mtk_claim_iso_intf(struct btusb_data *data)
2643{
2644 struct btmtk_data *btmtk_data = hci_get_priv(data->hdev);
2645 int err;
2646
2647 /*
2648 * The function usb_driver_claim_interface() is documented to need
2649 * locks held if it's not called from a probe routine. The code here
2650 * is called from the hci_power_on workqueue, so grab the lock.
2651 */
2652 device_lock(&btmtk_data->isopkt_intf->dev);
2653 err = usb_driver_claim_interface(&btusb_driver,
2654 btmtk_data->isopkt_intf, data);
2655 device_unlock(&btmtk_data->isopkt_intf->dev);
2656 if (err < 0) {
2657 btmtk_data->isopkt_intf = NULL;
2658 bt_dev_err(data->hdev, "Failed to claim iso interface");
2659 return;
2660 }
2661
2662 set_bit(BTMTK_ISOPKT_OVER_INTR, &btmtk_data->flags);
2663 init_usb_anchor(&btmtk_data->isopkt_anchor);
2664}
2665
2666static void btusb_mtk_release_iso_intf(struct hci_dev *hdev)
2667{
2668 struct btmtk_data *btmtk_data = hci_get_priv(hdev);
2669
2670 if (test_bit(BTMTK_ISOPKT_OVER_INTR, &btmtk_data->flags)) {
2671 usb_kill_anchored_urbs(&btmtk_data->isopkt_anchor);
2672 clear_bit(BTMTK_ISOPKT_RUNNING, &btmtk_data->flags);
2673
2674 dev_kfree_skb_irq(btmtk_data->isopkt_skb);
2675 btmtk_data->isopkt_skb = NULL;
2676 usb_set_intfdata(btmtk_data->isopkt_intf, NULL);
2677 usb_driver_release_interface(&btusb_driver,
2678 btmtk_data->isopkt_intf);
2679 }
2680
2681 clear_bit(BTMTK_ISOPKT_OVER_INTR, &btmtk_data->flags);
2682}
2683
2684static int btusb_mtk_disconnect(struct hci_dev *hdev)
2685{
2686 /* This function describes the specific additional steps taken by MediaTek
2687 * when Bluetooth usb driver's resume function is called.
2688 */
2689 btusb_mtk_release_iso_intf(hdev);
2690
2691 return 0;
2692}
2693
2694static int btusb_mtk_reset(struct hci_dev *hdev, void *rst_data)
2695{
2696 struct btusb_data *data = hci_get_drvdata(hdev);
2697 struct btmtk_data *btmtk_data = hci_get_priv(hdev);
2698 int err;
2699
2700 /* It's MediaTek specific bluetooth reset mechanism via USB */
2701 if (test_and_set_bit(BTMTK_HW_RESET_ACTIVE, &btmtk_data->flags)) {
2702 bt_dev_err(hdev, "last reset failed? Not resetting again");
2703 return -EBUSY;
2704 }
2705
2706 err = usb_autopm_get_interface(data->intf);
2707 if (err < 0)
2708 return err;
2709
2710 /* Release MediaTek ISO data interface */
2711 btusb_mtk_release_iso_intf(hdev);
2712
2713 btusb_stop_traffic(data);
2714 usb_kill_anchored_urbs(&data->tx_anchor);
2715
2716 err = btmtk_usb_subsys_reset(hdev, btmtk_data->dev_id);
2717
2718 usb_queue_reset_device(data->intf);
2719 clear_bit(BTMTK_HW_RESET_ACTIVE, &btmtk_data->flags);
2720
2721 return err;
2722}
2723
2724static int btusb_send_frame_mtk(struct hci_dev *hdev, struct sk_buff *skb)
2725{
2726 struct urb *urb;
2727
2728 BT_DBG("%s", hdev->name);
2729
2730 if (hci_skb_pkt_type(skb) == HCI_ISODATA_PKT) {
2731 urb = alloc_mtk_intr_urb(hdev, skb, btusb_tx_complete);
2732 if (IS_ERR(urb))
2733 return PTR_ERR(urb);
2734
2735 return submit_or_queue_tx_urb(hdev, urb);
2736 } else {
2737 return btusb_send_frame(hdev, skb);
2738 }
2739}
2740
2741static int btusb_mtk_setup(struct hci_dev *hdev)
2742{
2743 struct btusb_data *data = hci_get_drvdata(hdev);
2744 struct btmtk_data *btmtk_data = hci_get_priv(hdev);
2745
2746 /* MediaTek WMT vendor cmd requiring below USB resources to
2747 * complete the handshake.
2748 */
2749 btmtk_data->drv_name = btusb_driver.name;
2750 btmtk_data->intf = data->intf;
2751 btmtk_data->udev = data->udev;
2752 btmtk_data->ctrl_anchor = &data->ctrl_anchor;
2753 btmtk_data->reset_sync = btusb_mtk_reset;
2754
2755 /* Claim ISO data interface and endpoint */
2756 if (!test_bit(BTMTK_ISOPKT_OVER_INTR, &btmtk_data->flags)) {
2757 btmtk_data->isopkt_intf = usb_ifnum_to_if(data->udev, MTK_ISO_IFNUM);
2758 btusb_mtk_claim_iso_intf(data);
2759 }
2760
2761 return btmtk_usb_setup(hdev);
2762}
2763
2764static int btusb_mtk_shutdown(struct hci_dev *hdev)
2765{
2766 int ret;
2767
2768 ret = btmtk_usb_shutdown(hdev);
2769
2770 /* Release MediaTek iso interface after shutdown */
2771 btusb_mtk_release_iso_intf(hdev);
2772
2773 return ret;
2774}
2775
2776#ifdef CONFIG_PM
2777/* Configure an out-of-band gpio as wake-up pin, if specified in device tree */
2778static int marvell_config_oob_wake(struct hci_dev *hdev)
2779{
2780 struct sk_buff *skb;
2781 struct btusb_data *data = hci_get_drvdata(hdev);
2782 struct device *dev = &data->udev->dev;
2783 u16 pin, gap, opcode;
2784 int ret;
2785 u8 cmd[5];
2786
2787 /* Move on if no wakeup pin specified */
2788 if (of_property_read_u16(dev->of_node, "marvell,wakeup-pin", &pin) ||
2789 of_property_read_u16(dev->of_node, "marvell,wakeup-gap-ms", &gap))
2790 return 0;
2791
2792 /* Vendor specific command to configure a GPIO as wake-up pin */
2793 opcode = hci_opcode_pack(0x3F, 0x59);
2794 cmd[0] = opcode & 0xFF;
2795 cmd[1] = opcode >> 8;
2796 cmd[2] = 2; /* length of parameters that follow */
2797 cmd[3] = pin;
2798 cmd[4] = gap; /* time in ms, for which wakeup pin should be asserted */
2799
2800 skb = bt_skb_alloc(sizeof(cmd), GFP_KERNEL);
2801 if (!skb) {
2802 bt_dev_err(hdev, "%s: No memory", __func__);
2803 return -ENOMEM;
2804 }
2805
2806 skb_put_data(skb, cmd, sizeof(cmd));
2807 hci_skb_pkt_type(skb) = HCI_COMMAND_PKT;
2808
2809 ret = btusb_send_frame(hdev, skb);
2810 if (ret) {
2811 bt_dev_err(hdev, "%s: configuration failed", __func__);
2812 kfree_skb(skb);
2813 return ret;
2814 }
2815
2816 return 0;
2817}
2818#endif
2819
2820static int btusb_set_bdaddr_marvell(struct hci_dev *hdev,
2821 const bdaddr_t *bdaddr)
2822{
2823 struct sk_buff *skb;
2824 u8 buf[8];
2825 long ret;
2826
2827 buf[0] = 0xfe;
2828 buf[1] = sizeof(bdaddr_t);
2829 memcpy(buf + 2, bdaddr, sizeof(bdaddr_t));
2830
2831 skb = __hci_cmd_sync(hdev, 0xfc22, sizeof(buf), buf, HCI_INIT_TIMEOUT);
2832 if (IS_ERR(skb)) {
2833 ret = PTR_ERR(skb);
2834 bt_dev_err(hdev, "changing Marvell device address failed (%ld)",
2835 ret);
2836 return ret;
2837 }
2838 kfree_skb(skb);
2839
2840 return 0;
2841}
2842
2843static int btusb_set_bdaddr_ath3012(struct hci_dev *hdev,
2844 const bdaddr_t *bdaddr)
2845{
2846 struct sk_buff *skb;
2847 u8 buf[10];
2848 long ret;
2849
2850 buf[0] = 0x01;
2851 buf[1] = 0x01;
2852 buf[2] = 0x00;
2853 buf[3] = sizeof(bdaddr_t);
2854 memcpy(buf + 4, bdaddr, sizeof(bdaddr_t));
2855
2856 skb = __hci_cmd_sync(hdev, 0xfc0b, sizeof(buf), buf, HCI_INIT_TIMEOUT);
2857 if (IS_ERR(skb)) {
2858 ret = PTR_ERR(skb);
2859 bt_dev_err(hdev, "Change address command failed (%ld)", ret);
2860 return ret;
2861 }
2862 kfree_skb(skb);
2863
2864 return 0;
2865}
2866
2867static int btusb_set_bdaddr_wcn6855(struct hci_dev *hdev,
2868 const bdaddr_t *bdaddr)
2869{
2870 struct sk_buff *skb;
2871 u8 buf[6];
2872 long ret;
2873
2874 memcpy(buf, bdaddr, sizeof(bdaddr_t));
2875
2876 skb = __hci_cmd_sync_ev(hdev, 0xfc14, sizeof(buf), buf,
2877 HCI_EV_CMD_COMPLETE, HCI_INIT_TIMEOUT);
2878 if (IS_ERR(skb)) {
2879 ret = PTR_ERR(skb);
2880 bt_dev_err(hdev, "Change address command failed (%ld)", ret);
2881 return ret;
2882 }
2883 kfree_skb(skb);
2884
2885 return 0;
2886}
2887
2888#define QCA_MEMDUMP_ACL_HANDLE 0x2EDD
2889#define QCA_MEMDUMP_SIZE_MAX 0x100000
2890#define QCA_MEMDUMP_VSE_CLASS 0x01
2891#define QCA_MEMDUMP_MSG_TYPE 0x08
2892#define QCA_MEMDUMP_PKT_SIZE 248
2893#define QCA_LAST_SEQUENCE_NUM 0xffff
2894
2895struct qca_dump_hdr {
2896 u8 vse_class;
2897 u8 msg_type;
2898 __le16 seqno;
2899 u8 reserved;
2900 union {
2901 u8 data[0];
2902 struct {
2903 __le32 ram_dump_size;
2904 u8 data0[0];
2905 } __packed;
2906 };
2907} __packed;
2908
2909
2910static void btusb_dump_hdr_qca(struct hci_dev *hdev, struct sk_buff *skb)
2911{
2912 char buf[128];
2913 struct btusb_data *btdata = hci_get_drvdata(hdev);
2914
2915 snprintf(buf, sizeof(buf), "Controller Name: 0x%x\n",
2916 btdata->qca_dump.controller_id);
2917 skb_put_data(skb, buf, strlen(buf));
2918
2919 snprintf(buf, sizeof(buf), "Firmware Version: 0x%x\n",
2920 btdata->qca_dump.fw_version);
2921 skb_put_data(skb, buf, strlen(buf));
2922
2923 snprintf(buf, sizeof(buf), "Driver: %s\nVendor: qca\n",
2924 btusb_driver.name);
2925 skb_put_data(skb, buf, strlen(buf));
2926
2927 snprintf(buf, sizeof(buf), "VID: 0x%x\nPID:0x%x\n",
2928 btdata->qca_dump.id_vendor, btdata->qca_dump.id_product);
2929 skb_put_data(skb, buf, strlen(buf));
2930
2931 snprintf(buf, sizeof(buf), "Lmp Subversion: 0x%x\n",
2932 hdev->lmp_subver);
2933 skb_put_data(skb, buf, strlen(buf));
2934}
2935
2936static void btusb_coredump_qca(struct hci_dev *hdev)
2937{
2938 int err;
2939 static const u8 param[] = { 0x26 };
2940
2941 err = __hci_cmd_send(hdev, 0xfc0c, 1, param);
2942 if (err < 0)
2943 bt_dev_err(hdev, "%s: triggle crash failed (%d)", __func__, err);
2944}
2945
2946/*
2947 * ==0: not a dump pkt.
2948 * < 0: fails to handle a dump pkt
2949 * > 0: otherwise.
2950 */
2951static int handle_dump_pkt_qca(struct hci_dev *hdev, struct sk_buff *skb)
2952{
2953 int ret = 1;
2954 u8 pkt_type;
2955 u8 *sk_ptr;
2956 unsigned int sk_len;
2957 u16 seqno;
2958 u32 dump_size;
2959
2960 struct hci_event_hdr *event_hdr;
2961 struct hci_acl_hdr *acl_hdr;
2962 struct qca_dump_hdr *dump_hdr;
2963 struct btusb_data *btdata = hci_get_drvdata(hdev);
2964 struct usb_device *udev = btdata->udev;
2965
2966 pkt_type = hci_skb_pkt_type(skb);
2967 sk_ptr = skb->data;
2968 sk_len = skb->len;
2969
2970 if (pkt_type == HCI_ACLDATA_PKT) {
2971 acl_hdr = hci_acl_hdr(skb);
2972 if (le16_to_cpu(acl_hdr->handle) != QCA_MEMDUMP_ACL_HANDLE)
2973 return 0;
2974 sk_ptr += HCI_ACL_HDR_SIZE;
2975 sk_len -= HCI_ACL_HDR_SIZE;
2976 event_hdr = (struct hci_event_hdr *)sk_ptr;
2977 } else {
2978 event_hdr = hci_event_hdr(skb);
2979 }
2980
2981 if ((event_hdr->evt != HCI_VENDOR_PKT)
2982 || (event_hdr->plen != (sk_len - HCI_EVENT_HDR_SIZE)))
2983 return 0;
2984
2985 sk_ptr += HCI_EVENT_HDR_SIZE;
2986 sk_len -= HCI_EVENT_HDR_SIZE;
2987
2988 dump_hdr = (struct qca_dump_hdr *)sk_ptr;
2989 if ((sk_len < offsetof(struct qca_dump_hdr, data))
2990 || (dump_hdr->vse_class != QCA_MEMDUMP_VSE_CLASS)
2991 || (dump_hdr->msg_type != QCA_MEMDUMP_MSG_TYPE))
2992 return 0;
2993
2994 /*it is dump pkt now*/
2995 seqno = le16_to_cpu(dump_hdr->seqno);
2996 if (seqno == 0) {
2997 set_bit(BTUSB_HW_SSR_ACTIVE, &btdata->flags);
2998 dump_size = le32_to_cpu(dump_hdr->ram_dump_size);
2999 if (!dump_size || (dump_size > QCA_MEMDUMP_SIZE_MAX)) {
3000 ret = -EILSEQ;
3001 bt_dev_err(hdev, "Invalid memdump size(%u)",
3002 dump_size);
3003 goto out;
3004 }
3005
3006 ret = hci_devcd_init(hdev, dump_size);
3007 if (ret < 0) {
3008 bt_dev_err(hdev, "memdump init error(%d)", ret);
3009 goto out;
3010 }
3011
3012 btdata->qca_dump.ram_dump_size = dump_size;
3013 btdata->qca_dump.ram_dump_seqno = 0;
3014 sk_ptr += offsetof(struct qca_dump_hdr, data0);
3015 sk_len -= offsetof(struct qca_dump_hdr, data0);
3016
3017 usb_disable_autosuspend(udev);
3018 bt_dev_info(hdev, "%s memdump size(%u)\n",
3019 (pkt_type == HCI_ACLDATA_PKT) ? "ACL" : "event",
3020 dump_size);
3021 } else {
3022 sk_ptr += offsetof(struct qca_dump_hdr, data);
3023 sk_len -= offsetof(struct qca_dump_hdr, data);
3024 }
3025
3026 if (!btdata->qca_dump.ram_dump_size) {
3027 ret = -EINVAL;
3028 bt_dev_err(hdev, "memdump is not active");
3029 goto out;
3030 }
3031
3032 if ((seqno > btdata->qca_dump.ram_dump_seqno + 1) && (seqno != QCA_LAST_SEQUENCE_NUM)) {
3033 dump_size = QCA_MEMDUMP_PKT_SIZE * (seqno - btdata->qca_dump.ram_dump_seqno - 1);
3034 hci_devcd_append_pattern(hdev, 0x0, dump_size);
3035 bt_dev_err(hdev,
3036 "expected memdump seqno(%u) is not received(%u)\n",
3037 btdata->qca_dump.ram_dump_seqno, seqno);
3038 btdata->qca_dump.ram_dump_seqno = seqno;
3039 kfree_skb(skb);
3040 return ret;
3041 }
3042
3043 skb_pull(skb, skb->len - sk_len);
3044 hci_devcd_append(hdev, skb);
3045 btdata->qca_dump.ram_dump_seqno++;
3046 if (seqno == QCA_LAST_SEQUENCE_NUM) {
3047 bt_dev_info(hdev,
3048 "memdump done: pkts(%u), total(%u)\n",
3049 btdata->qca_dump.ram_dump_seqno, btdata->qca_dump.ram_dump_size);
3050
3051 hci_devcd_complete(hdev);
3052 goto out;
3053 }
3054 return ret;
3055
3056out:
3057 if (btdata->qca_dump.ram_dump_size)
3058 usb_enable_autosuspend(udev);
3059 btdata->qca_dump.ram_dump_size = 0;
3060 btdata->qca_dump.ram_dump_seqno = 0;
3061 clear_bit(BTUSB_HW_SSR_ACTIVE, &btdata->flags);
3062
3063 if (ret < 0)
3064 kfree_skb(skb);
3065 return ret;
3066}
3067
3068static int btusb_recv_acl_qca(struct hci_dev *hdev, struct sk_buff *skb)
3069{
3070 if (handle_dump_pkt_qca(hdev, skb))
3071 return 0;
3072 return hci_recv_frame(hdev, skb);
3073}
3074
3075static int btusb_recv_evt_qca(struct hci_dev *hdev, struct sk_buff *skb)
3076{
3077 if (handle_dump_pkt_qca(hdev, skb))
3078 return 0;
3079 return hci_recv_frame(hdev, skb);
3080}
3081
3082
3083#define QCA_DFU_PACKET_LEN 4096
3084
3085#define QCA_GET_TARGET_VERSION 0x09
3086#define QCA_CHECK_STATUS 0x05
3087#define QCA_DFU_DOWNLOAD 0x01
3088
3089#define QCA_SYSCFG_UPDATED 0x40
3090#define QCA_PATCH_UPDATED 0x80
3091#define QCA_DFU_TIMEOUT 3000
3092#define QCA_FLAG_MULTI_NVM 0x80
3093#define QCA_BT_RESET_WAIT_MS 100
3094
3095#define WCN6855_2_0_RAM_VERSION_GF 0x400c1200
3096#define WCN6855_2_1_RAM_VERSION_GF 0x400c1211
3097
3098struct qca_version {
3099 __le32 rom_version;
3100 __le32 patch_version;
3101 __le32 ram_version;
3102 __u8 chip_id;
3103 __u8 platform_id;
3104 __le16 flag;
3105 __u8 reserved[4];
3106} __packed;
3107
3108struct qca_rampatch_version {
3109 __le16 rom_version_high;
3110 __le16 rom_version_low;
3111 __le16 patch_version;
3112} __packed;
3113
3114struct qca_device_info {
3115 u32 rom_version;
3116 u8 rampatch_hdr; /* length of header in rampatch */
3117 u8 nvm_hdr; /* length of header in NVM */
3118 u8 ver_offset; /* offset of version structure in rampatch */
3119};
3120
3121static const struct qca_device_info qca_devices_table[] = {
3122 { 0x00000100, 20, 4, 8 }, /* Rome 1.0 */
3123 { 0x00000101, 20, 4, 8 }, /* Rome 1.1 */
3124 { 0x00000200, 28, 4, 16 }, /* Rome 2.0 */
3125 { 0x00000201, 28, 4, 16 }, /* Rome 2.1 */
3126 { 0x00000300, 28, 4, 16 }, /* Rome 3.0 */
3127 { 0x00000302, 28, 4, 16 }, /* Rome 3.2 */
3128 { 0x00130100, 40, 4, 16 }, /* WCN6855 1.0 */
3129 { 0x00130200, 40, 4, 16 }, /* WCN6855 2.0 */
3130 { 0x00130201, 40, 4, 16 }, /* WCN6855 2.1 */
3131 { 0x00190200, 40, 4, 16 }, /* WCN785x 2.0 */
3132};
3133
3134static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 request,
3135 void *data, u16 size)
3136{
3137 int pipe, err;
3138 u8 *buf;
3139
3140 buf = kmalloc(size, GFP_KERNEL);
3141 if (!buf)
3142 return -ENOMEM;
3143
3144 /* Found some of USB hosts have IOT issues with ours so that we should
3145 * not wait until HCI layer is ready.
3146 */
3147 pipe = usb_rcvctrlpipe(udev, 0);
3148 err = usb_control_msg(udev, pipe, request, USB_TYPE_VENDOR | USB_DIR_IN,
3149 0, 0, buf, size, USB_CTRL_GET_TIMEOUT);
3150 if (err < 0) {
3151 dev_err(&udev->dev, "Failed to access otp area (%d)", err);
3152 goto done;
3153 }
3154
3155 memcpy(data, buf, size);
3156
3157done:
3158 kfree(buf);
3159
3160 return err;
3161}
3162
3163static int btusb_setup_qca_download_fw(struct hci_dev *hdev,
3164 const struct firmware *firmware,
3165 size_t hdr_size)
3166{
3167 struct btusb_data *btdata = hci_get_drvdata(hdev);
3168 struct usb_device *udev = btdata->udev;
3169 size_t count, size, sent = 0;
3170 int pipe, len, err;
3171 u8 *buf;
3172
3173 buf = kmalloc(QCA_DFU_PACKET_LEN, GFP_KERNEL);
3174 if (!buf)
3175 return -ENOMEM;
3176
3177 count = firmware->size;
3178
3179 size = min_t(size_t, count, hdr_size);
3180 memcpy(buf, firmware->data, size);
3181
3182 /* USB patches should go down to controller through USB path
3183 * because binary format fits to go down through USB channel.
3184 * USB control path is for patching headers and USB bulk is for
3185 * patch body.
3186 */
3187 pipe = usb_sndctrlpipe(udev, 0);
3188 err = usb_control_msg(udev, pipe, QCA_DFU_DOWNLOAD, USB_TYPE_VENDOR,
3189 0, 0, buf, size, USB_CTRL_SET_TIMEOUT);
3190 if (err < 0) {
3191 bt_dev_err(hdev, "Failed to send headers (%d)", err);
3192 goto done;
3193 }
3194
3195 sent += size;
3196 count -= size;
3197
3198 /* ep2 need time to switch from function acl to function dfu,
3199 * so we add 20ms delay here.
3200 */
3201 msleep(20);
3202
3203 while (count) {
3204 size = min_t(size_t, count, QCA_DFU_PACKET_LEN);
3205
3206 memcpy(buf, firmware->data + sent, size);
3207
3208 pipe = usb_sndbulkpipe(udev, 0x02);
3209 err = usb_bulk_msg(udev, pipe, buf, size, &len,
3210 QCA_DFU_TIMEOUT);
3211 if (err < 0) {
3212 bt_dev_err(hdev, "Failed to send body at %zd of %zd (%d)",
3213 sent, firmware->size, err);
3214 break;
3215 }
3216
3217 if (size != len) {
3218 bt_dev_err(hdev, "Failed to get bulk buffer");
3219 err = -EILSEQ;
3220 break;
3221 }
3222
3223 sent += size;
3224 count -= size;
3225 }
3226
3227done:
3228 kfree(buf);
3229 return err;
3230}
3231
3232static int btusb_setup_qca_load_rampatch(struct hci_dev *hdev,
3233 struct qca_version *ver,
3234 const struct qca_device_info *info)
3235{
3236 struct qca_rampatch_version *rver;
3237 const struct firmware *fw;
3238 u32 ver_rom, ver_patch, rver_rom;
3239 u16 rver_rom_low, rver_rom_high, rver_patch;
3240 char fwname[64];
3241 int err;
3242
3243 ver_rom = le32_to_cpu(ver->rom_version);
3244 ver_patch = le32_to_cpu(ver->patch_version);
3245
3246 snprintf(fwname, sizeof(fwname), "qca/rampatch_usb_%08x.bin", ver_rom);
3247
3248 err = request_firmware(&fw, fwname, &hdev->dev);
3249 if (err) {
3250 bt_dev_err(hdev, "failed to request rampatch file: %s (%d)",
3251 fwname, err);
3252 return err;
3253 }
3254
3255 bt_dev_info(hdev, "using rampatch file: %s", fwname);
3256
3257 rver = (struct qca_rampatch_version *)(fw->data + info->ver_offset);
3258 rver_rom_low = le16_to_cpu(rver->rom_version_low);
3259 rver_patch = le16_to_cpu(rver->patch_version);
3260
3261 if (ver_rom & ~0xffffU) {
3262 rver_rom_high = le16_to_cpu(rver->rom_version_high);
3263 rver_rom = rver_rom_high << 16 | rver_rom_low;
3264 } else {
3265 rver_rom = rver_rom_low;
3266 }
3267
3268 bt_dev_info(hdev, "QCA: patch rome 0x%x build 0x%x, "
3269 "firmware rome 0x%x build 0x%x",
3270 rver_rom, rver_patch, ver_rom, ver_patch);
3271
3272 if (rver_rom != ver_rom || rver_patch <= ver_patch) {
3273 bt_dev_err(hdev, "rampatch file version did not match with firmware");
3274 err = -EINVAL;
3275 goto done;
3276 }
3277
3278 err = btusb_setup_qca_download_fw(hdev, fw, info->rampatch_hdr);
3279
3280done:
3281 release_firmware(fw);
3282
3283 return err;
3284}
3285
3286static void btusb_generate_qca_nvm_name(char *fwname, size_t max_size,
3287 const struct qca_version *ver)
3288{
3289 u32 rom_version = le32_to_cpu(ver->rom_version);
3290 u16 flag = le16_to_cpu(ver->flag);
3291
3292 if (((flag >> 8) & 0xff) == QCA_FLAG_MULTI_NVM) {
3293 /* The board_id should be split into two bytes
3294 * The 1st byte is chip ID, and the 2nd byte is platform ID
3295 * For example, board ID 0x010A, 0x01 is platform ID. 0x0A is chip ID
3296 * we have several platforms, and platform IDs are continuously added
3297 * Platform ID:
3298 * 0x00 is for Mobile
3299 * 0x01 is for X86
3300 * 0x02 is for Automotive
3301 * 0x03 is for Consumer electronic
3302 */
3303 u16 board_id = (ver->chip_id << 8) + ver->platform_id;
3304 const char *variant;
3305
3306 switch (le32_to_cpu(ver->ram_version)) {
3307 case WCN6855_2_0_RAM_VERSION_GF:
3308 case WCN6855_2_1_RAM_VERSION_GF:
3309 variant = "_gf";
3310 break;
3311 default:
3312 variant = "";
3313 break;
3314 }
3315
3316 if (board_id == 0) {
3317 snprintf(fwname, max_size, "qca/nvm_usb_%08x%s.bin",
3318 rom_version, variant);
3319 } else {
3320 snprintf(fwname, max_size, "qca/nvm_usb_%08x%s_%04x.bin",
3321 rom_version, variant, board_id);
3322 }
3323 } else {
3324 snprintf(fwname, max_size, "qca/nvm_usb_%08x.bin",
3325 rom_version);
3326 }
3327
3328}
3329
3330static int btusb_setup_qca_load_nvm(struct hci_dev *hdev,
3331 struct qca_version *ver,
3332 const struct qca_device_info *info)
3333{
3334 const struct firmware *fw;
3335 char fwname[64];
3336 int err;
3337
3338 btusb_generate_qca_nvm_name(fwname, sizeof(fwname), ver);
3339
3340 err = request_firmware(&fw, fwname, &hdev->dev);
3341 if (err) {
3342 bt_dev_err(hdev, "failed to request NVM file: %s (%d)",
3343 fwname, err);
3344 return err;
3345 }
3346
3347 bt_dev_info(hdev, "using NVM file: %s", fwname);
3348
3349 err = btusb_setup_qca_download_fw(hdev, fw, info->nvm_hdr);
3350
3351 release_firmware(fw);
3352
3353 return err;
3354}
3355
3356/* identify the ROM version and check whether patches are needed */
3357static bool btusb_qca_need_patch(struct usb_device *udev)
3358{
3359 struct qca_version ver;
3360
3361 if (btusb_qca_send_vendor_req(udev, QCA_GET_TARGET_VERSION, &ver,
3362 sizeof(ver)) < 0)
3363 return false;
3364 /* only low ROM versions need patches */
3365 return !(le32_to_cpu(ver.rom_version) & ~0xffffU);
3366}
3367
3368static int btusb_setup_qca(struct hci_dev *hdev)
3369{
3370 struct btusb_data *btdata = hci_get_drvdata(hdev);
3371 struct usb_device *udev = btdata->udev;
3372 const struct qca_device_info *info = NULL;
3373 struct qca_version ver;
3374 u32 ver_rom;
3375 u8 status;
3376 int i, err;
3377
3378 err = btusb_qca_send_vendor_req(udev, QCA_GET_TARGET_VERSION, &ver,
3379 sizeof(ver));
3380 if (err < 0)
3381 return err;
3382
3383 ver_rom = le32_to_cpu(ver.rom_version);
3384
3385 for (i = 0; i < ARRAY_SIZE(qca_devices_table); i++) {
3386 if (ver_rom == qca_devices_table[i].rom_version)
3387 info = &qca_devices_table[i];
3388 }
3389 if (!info) {
3390 /* If the rom_version is not matched in the qca_devices_table
3391 * and the high ROM version is not zero, we assume this chip no
3392 * need to load the rampatch and nvm.
3393 */
3394 if (ver_rom & ~0xffffU)
3395 return 0;
3396
3397 bt_dev_err(hdev, "don't support firmware rome 0x%x", ver_rom);
3398 return -ENODEV;
3399 }
3400
3401 err = btusb_qca_send_vendor_req(udev, QCA_CHECK_STATUS, &status,
3402 sizeof(status));
3403 if (err < 0)
3404 return err;
3405
3406 if (!(status & QCA_PATCH_UPDATED)) {
3407 err = btusb_setup_qca_load_rampatch(hdev, &ver, info);
3408 if (err < 0)
3409 return err;
3410 }
3411
3412 err = btusb_qca_send_vendor_req(udev, QCA_GET_TARGET_VERSION, &ver,
3413 sizeof(ver));
3414 if (err < 0)
3415 return err;
3416
3417 btdata->qca_dump.fw_version = le32_to_cpu(ver.patch_version);
3418 btdata->qca_dump.controller_id = le32_to_cpu(ver.rom_version);
3419
3420 if (!(status & QCA_SYSCFG_UPDATED)) {
3421 err = btusb_setup_qca_load_nvm(hdev, &ver, info);
3422 if (err < 0)
3423 return err;
3424
3425 /* WCN6855 2.1 and later will reset to apply firmware downloaded here, so
3426 * wait ~100ms for reset Done then go ahead, otherwise, it maybe
3427 * cause potential enable failure.
3428 */
3429 if (info->rom_version >= 0x00130201)
3430 msleep(QCA_BT_RESET_WAIT_MS);
3431 }
3432
3433 /* Mark HCI_OP_ENHANCED_SETUP_SYNC_CONN as broken as it doesn't seem to
3434 * work with the likes of HSP/HFP mSBC.
3435 */
3436 set_bit(HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN, &hdev->quirks);
3437
3438 return 0;
3439}
3440
3441static inline int __set_diag_interface(struct hci_dev *hdev)
3442{
3443 struct btusb_data *data = hci_get_drvdata(hdev);
3444 struct usb_interface *intf = data->diag;
3445 int i;
3446
3447 if (!data->diag)
3448 return -ENODEV;
3449
3450 data->diag_tx_ep = NULL;
3451 data->diag_rx_ep = NULL;
3452
3453 for (i = 0; i < intf->cur_altsetting->desc.bNumEndpoints; i++) {
3454 struct usb_endpoint_descriptor *ep_desc;
3455
3456 ep_desc = &intf->cur_altsetting->endpoint[i].desc;
3457
3458 if (!data->diag_tx_ep && usb_endpoint_is_bulk_out(ep_desc)) {
3459 data->diag_tx_ep = ep_desc;
3460 continue;
3461 }
3462
3463 if (!data->diag_rx_ep && usb_endpoint_is_bulk_in(ep_desc)) {
3464 data->diag_rx_ep = ep_desc;
3465 continue;
3466 }
3467 }
3468
3469 if (!data->diag_tx_ep || !data->diag_rx_ep) {
3470 bt_dev_err(hdev, "invalid diagnostic descriptors");
3471 return -ENODEV;
3472 }
3473
3474 return 0;
3475}
3476
3477static struct urb *alloc_diag_urb(struct hci_dev *hdev, bool enable)
3478{
3479 struct btusb_data *data = hci_get_drvdata(hdev);
3480 struct sk_buff *skb;
3481 struct urb *urb;
3482 unsigned int pipe;
3483
3484 if (!data->diag_tx_ep)
3485 return ERR_PTR(-ENODEV);
3486
3487 urb = usb_alloc_urb(0, GFP_KERNEL);
3488 if (!urb)
3489 return ERR_PTR(-ENOMEM);
3490
3491 skb = bt_skb_alloc(2, GFP_KERNEL);
3492 if (!skb) {
3493 usb_free_urb(urb);
3494 return ERR_PTR(-ENOMEM);
3495 }
3496
3497 skb_put_u8(skb, 0xf0);
3498 skb_put_u8(skb, enable);
3499
3500 pipe = usb_sndbulkpipe(data->udev, data->diag_tx_ep->bEndpointAddress);
3501
3502 usb_fill_bulk_urb(urb, data->udev, pipe,
3503 skb->data, skb->len, btusb_tx_complete, skb);
3504
3505 skb->dev = (void *)hdev;
3506
3507 return urb;
3508}
3509
3510static int btusb_bcm_set_diag(struct hci_dev *hdev, bool enable)
3511{
3512 struct btusb_data *data = hci_get_drvdata(hdev);
3513 struct urb *urb;
3514
3515 if (!data->diag)
3516 return -ENODEV;
3517
3518 if (!test_bit(HCI_RUNNING, &hdev->flags))
3519 return -ENETDOWN;
3520
3521 urb = alloc_diag_urb(hdev, enable);
3522 if (IS_ERR(urb))
3523 return PTR_ERR(urb);
3524
3525 return submit_or_queue_tx_urb(hdev, urb);
3526}
3527
3528#ifdef CONFIG_PM
3529static irqreturn_t btusb_oob_wake_handler(int irq, void *priv)
3530{
3531 struct btusb_data *data = priv;
3532
3533 pm_wakeup_event(&data->udev->dev, 0);
3534 pm_system_wakeup();
3535
3536 /* Disable only if not already disabled (keep it balanced) */
3537 if (test_and_clear_bit(BTUSB_OOB_WAKE_ENABLED, &data->flags)) {
3538 disable_irq_nosync(irq);
3539 disable_irq_wake(irq);
3540 }
3541 return IRQ_HANDLED;
3542}
3543
3544static const struct of_device_id btusb_match_table[] = {
3545 { .compatible = "usb1286,204e" },
3546 { .compatible = "usbcf3,e300" }, /* QCA6174A */
3547 { .compatible = "usb4ca,301a" }, /* QCA6174A (Lite-On) */
3548 { }
3549};
3550MODULE_DEVICE_TABLE(of, btusb_match_table);
3551
3552/* Use an oob wakeup pin? */
3553static int btusb_config_oob_wake(struct hci_dev *hdev)
3554{
3555 struct btusb_data *data = hci_get_drvdata(hdev);
3556 struct device *dev = &data->udev->dev;
3557 int irq, ret;
3558
3559 clear_bit(BTUSB_OOB_WAKE_ENABLED, &data->flags);
3560
3561 if (!of_match_device(btusb_match_table, dev))
3562 return 0;
3563
3564 /* Move on if no IRQ specified */
3565 irq = of_irq_get_byname(dev->of_node, "wakeup");
3566 if (irq <= 0) {
3567 bt_dev_dbg(hdev, "%s: no OOB Wakeup IRQ in DT", __func__);
3568 return 0;
3569 }
3570
3571 irq_set_status_flags(irq, IRQ_NOAUTOEN);
3572 ret = devm_request_irq(&hdev->dev, irq, btusb_oob_wake_handler,
3573 0, "OOB Wake-on-BT", data);
3574 if (ret) {
3575 bt_dev_err(hdev, "%s: IRQ request failed", __func__);
3576 return ret;
3577 }
3578
3579 ret = device_init_wakeup(dev, true);
3580 if (ret) {
3581 bt_dev_err(hdev, "%s: failed to init_wakeup", __func__);
3582 return ret;
3583 }
3584
3585 data->oob_wake_irq = irq;
3586 bt_dev_info(hdev, "OOB Wake-on-BT configured at IRQ %u", irq);
3587 return 0;
3588}
3589#endif
3590
3591static void btusb_check_needs_reset_resume(struct usb_interface *intf)
3592{
3593 if (dmi_check_system(btusb_needs_reset_resume_table))
3594 interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME;
3595}
3596
3597static bool btusb_wakeup(struct hci_dev *hdev)
3598{
3599 struct btusb_data *data = hci_get_drvdata(hdev);
3600
3601 return device_may_wakeup(&data->udev->dev);
3602}
3603
3604static int btusb_shutdown_qca(struct hci_dev *hdev)
3605{
3606 struct sk_buff *skb;
3607
3608 skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL, HCI_INIT_TIMEOUT);
3609 if (IS_ERR(skb)) {
3610 bt_dev_err(hdev, "HCI reset during shutdown failed");
3611 return PTR_ERR(skb);
3612 }
3613 kfree_skb(skb);
3614
3615 return 0;
3616}
3617
3618static ssize_t force_poll_sync_read(struct file *file, char __user *user_buf,
3619 size_t count, loff_t *ppos)
3620{
3621 struct btusb_data *data = file->private_data;
3622 char buf[3];
3623
3624 buf[0] = data->poll_sync ? 'Y' : 'N';
3625 buf[1] = '\n';
3626 buf[2] = '\0';
3627 return simple_read_from_buffer(user_buf, count, ppos, buf, 2);
3628}
3629
3630static ssize_t force_poll_sync_write(struct file *file,
3631 const char __user *user_buf,
3632 size_t count, loff_t *ppos)
3633{
3634 struct btusb_data *data = file->private_data;
3635 bool enable;
3636 int err;
3637
3638 err = kstrtobool_from_user(user_buf, count, &enable);
3639 if (err)
3640 return err;
3641
3642 /* Only allow changes while the adapter is down */
3643 if (test_bit(HCI_UP, &data->hdev->flags))
3644 return -EPERM;
3645
3646 if (data->poll_sync == enable)
3647 return -EALREADY;
3648
3649 data->poll_sync = enable;
3650
3651 return count;
3652}
3653
3654static const struct file_operations force_poll_sync_fops = {
3655 .owner = THIS_MODULE,
3656 .open = simple_open,
3657 .read = force_poll_sync_read,
3658 .write = force_poll_sync_write,
3659 .llseek = default_llseek,
3660};
3661
3662static int btusb_probe(struct usb_interface *intf,
3663 const struct usb_device_id *id)
3664{
3665 struct usb_endpoint_descriptor *ep_desc;
3666 struct gpio_desc *reset_gpio;
3667 struct btusb_data *data;
3668 struct hci_dev *hdev;
3669 unsigned ifnum_base;
3670 int i, err, priv_size;
3671
3672 BT_DBG("intf %p id %p", intf, id);
3673
3674 if ((id->driver_info & BTUSB_IFNUM_2) &&
3675 (intf->cur_altsetting->desc.bInterfaceNumber != 0) &&
3676 (intf->cur_altsetting->desc.bInterfaceNumber != 2))
3677 return -ENODEV;
3678
3679 ifnum_base = intf->cur_altsetting->desc.bInterfaceNumber;
3680
3681 if (!id->driver_info) {
3682 const struct usb_device_id *match;
3683
3684 match = usb_match_id(intf, quirks_table);
3685 if (match)
3686 id = match;
3687 }
3688
3689 if (id->driver_info == BTUSB_IGNORE)
3690 return -ENODEV;
3691
3692 if (id->driver_info & BTUSB_ATH3012) {
3693 struct usb_device *udev = interface_to_usbdev(intf);
3694
3695 /* Old firmware would otherwise let ath3k driver load
3696 * patch and sysconfig files
3697 */
3698 if (le16_to_cpu(udev->descriptor.bcdDevice) <= 0x0001 &&
3699 !btusb_qca_need_patch(udev))
3700 return -ENODEV;
3701 }
3702
3703 data = devm_kzalloc(&intf->dev, sizeof(*data), GFP_KERNEL);
3704 if (!data)
3705 return -ENOMEM;
3706
3707 for (i = 0; i < intf->cur_altsetting->desc.bNumEndpoints; i++) {
3708 ep_desc = &intf->cur_altsetting->endpoint[i].desc;
3709
3710 if (!data->intr_ep && usb_endpoint_is_int_in(ep_desc)) {
3711 data->intr_ep = ep_desc;
3712 continue;
3713 }
3714
3715 if (!data->bulk_tx_ep && usb_endpoint_is_bulk_out(ep_desc)) {
3716 data->bulk_tx_ep = ep_desc;
3717 continue;
3718 }
3719
3720 if (!data->bulk_rx_ep && usb_endpoint_is_bulk_in(ep_desc)) {
3721 data->bulk_rx_ep = ep_desc;
3722 continue;
3723 }
3724 }
3725
3726 if (!data->intr_ep || !data->bulk_tx_ep || !data->bulk_rx_ep)
3727 return -ENODEV;
3728
3729 if (id->driver_info & BTUSB_AMP) {
3730 data->cmdreq_type = USB_TYPE_CLASS | 0x01;
3731 data->cmdreq = 0x2b;
3732 } else {
3733 data->cmdreq_type = USB_TYPE_CLASS;
3734 data->cmdreq = 0x00;
3735 }
3736
3737 data->udev = interface_to_usbdev(intf);
3738 data->intf = intf;
3739
3740 INIT_WORK(&data->work, btusb_work);
3741 INIT_WORK(&data->waker, btusb_waker);
3742 INIT_DELAYED_WORK(&data->rx_work, btusb_rx_work);
3743
3744 skb_queue_head_init(&data->acl_q);
3745
3746 init_usb_anchor(&data->deferred);
3747 init_usb_anchor(&data->tx_anchor);
3748 spin_lock_init(&data->txlock);
3749
3750 init_usb_anchor(&data->intr_anchor);
3751 init_usb_anchor(&data->bulk_anchor);
3752 init_usb_anchor(&data->isoc_anchor);
3753 init_usb_anchor(&data->diag_anchor);
3754 init_usb_anchor(&data->ctrl_anchor);
3755 spin_lock_init(&data->rxlock);
3756
3757 priv_size = 0;
3758
3759 data->recv_event = hci_recv_frame;
3760 data->recv_bulk = btusb_recv_bulk;
3761
3762 if (id->driver_info & BTUSB_INTEL_COMBINED) {
3763 /* Allocate extra space for Intel device */
3764 priv_size += sizeof(struct btintel_data);
3765
3766 /* Override the rx handlers */
3767 data->recv_event = btintel_recv_event;
3768 data->recv_bulk = btusb_recv_bulk_intel;
3769 } else if (id->driver_info & BTUSB_REALTEK) {
3770 /* Allocate extra space for Realtek device */
3771 priv_size += sizeof(struct btrealtek_data);
3772
3773 data->recv_event = btusb_recv_event_realtek;
3774 } else if (id->driver_info & BTUSB_MEDIATEK) {
3775 /* Allocate extra space for Mediatek device */
3776 priv_size += sizeof(struct btmtk_data);
3777 }
3778
3779 data->recv_acl = hci_recv_frame;
3780
3781 hdev = hci_alloc_dev_priv(priv_size);
3782 if (!hdev)
3783 return -ENOMEM;
3784
3785 hdev->bus = HCI_USB;
3786 hci_set_drvdata(hdev, data);
3787
3788 data->hdev = hdev;
3789
3790 SET_HCIDEV_DEV(hdev, &intf->dev);
3791
3792 reset_gpio = gpiod_get_optional(&data->udev->dev, "reset",
3793 GPIOD_OUT_LOW);
3794 if (IS_ERR(reset_gpio)) {
3795 err = PTR_ERR(reset_gpio);
3796 goto out_free_dev;
3797 } else if (reset_gpio) {
3798 data->reset_gpio = reset_gpio;
3799 }
3800
3801 hdev->open = btusb_open;
3802 hdev->close = btusb_close;
3803 hdev->flush = btusb_flush;
3804 hdev->send = btusb_send_frame;
3805 hdev->notify = btusb_notify;
3806 hdev->wakeup = btusb_wakeup;
3807
3808#ifdef CONFIG_PM
3809 err = btusb_config_oob_wake(hdev);
3810 if (err)
3811 goto out_free_dev;
3812
3813 /* Marvell devices may need a specific chip configuration */
3814 if (id->driver_info & BTUSB_MARVELL && data->oob_wake_irq) {
3815 err = marvell_config_oob_wake(hdev);
3816 if (err)
3817 goto out_free_dev;
3818 }
3819#endif
3820 if (id->driver_info & BTUSB_CW6622)
3821 set_bit(HCI_QUIRK_BROKEN_STORED_LINK_KEY, &hdev->quirks);
3822
3823 if (id->driver_info & BTUSB_BCM2045)
3824 set_bit(HCI_QUIRK_BROKEN_STORED_LINK_KEY, &hdev->quirks);
3825
3826 if (id->driver_info & BTUSB_BCM92035)
3827 hdev->setup = btusb_setup_bcm92035;
3828
3829 if (IS_ENABLED(CONFIG_BT_HCIBTUSB_BCM) &&
3830 (id->driver_info & BTUSB_BCM_PATCHRAM)) {
3831 hdev->manufacturer = 15;
3832 hdev->setup = btbcm_setup_patchram;
3833 hdev->set_diag = btusb_bcm_set_diag;
3834 hdev->set_bdaddr = btbcm_set_bdaddr;
3835
3836 /* Broadcom LM_DIAG Interface numbers are hardcoded */
3837 data->diag = usb_ifnum_to_if(data->udev, ifnum_base + 2);
3838 }
3839
3840 if (IS_ENABLED(CONFIG_BT_HCIBTUSB_BCM) &&
3841 (id->driver_info & BTUSB_BCM_APPLE)) {
3842 hdev->manufacturer = 15;
3843 hdev->setup = btbcm_setup_apple;
3844 hdev->set_diag = btusb_bcm_set_diag;
3845
3846 /* Broadcom LM_DIAG Interface numbers are hardcoded */
3847 data->diag = usb_ifnum_to_if(data->udev, ifnum_base + 2);
3848 }
3849
3850 /* Combined Intel Device setup to support multiple setup routine */
3851 if (id->driver_info & BTUSB_INTEL_COMBINED) {
3852 err = btintel_configure_setup(hdev, btusb_driver.name);
3853 if (err)
3854 goto out_free_dev;
3855
3856 /* Transport specific configuration */
3857 hdev->send = btusb_send_frame_intel;
3858 hdev->cmd_timeout = btusb_intel_cmd_timeout;
3859
3860 if (id->driver_info & BTUSB_INTEL_NO_WBS_SUPPORT)
3861 btintel_set_flag(hdev, INTEL_ROM_LEGACY_NO_WBS_SUPPORT);
3862
3863 if (id->driver_info & BTUSB_INTEL_BROKEN_INITIAL_NCMD)
3864 btintel_set_flag(hdev, INTEL_BROKEN_INITIAL_NCMD);
3865
3866 if (id->driver_info & BTUSB_INTEL_BROKEN_SHUTDOWN_LED)
3867 btintel_set_flag(hdev, INTEL_BROKEN_SHUTDOWN_LED);
3868 }
3869
3870 if (id->driver_info & BTUSB_MARVELL)
3871 hdev->set_bdaddr = btusb_set_bdaddr_marvell;
3872
3873 if (IS_ENABLED(CONFIG_BT_HCIBTUSB_MTK) &&
3874 (id->driver_info & BTUSB_MEDIATEK)) {
3875 hdev->setup = btusb_mtk_setup;
3876 hdev->shutdown = btusb_mtk_shutdown;
3877 hdev->manufacturer = 70;
3878 hdev->cmd_timeout = btmtk_reset_sync;
3879 hdev->set_bdaddr = btmtk_set_bdaddr;
3880 hdev->send = btusb_send_frame_mtk;
3881 set_bit(HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN, &hdev->quirks);
3882 set_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks);
3883 data->recv_acl = btmtk_usb_recv_acl;
3884 data->suspend = btmtk_usb_suspend;
3885 data->resume = btmtk_usb_resume;
3886 data->disconnect = btusb_mtk_disconnect;
3887 }
3888
3889 if (id->driver_info & BTUSB_SWAVE) {
3890 set_bit(HCI_QUIRK_FIXUP_INQUIRY_MODE, &hdev->quirks);
3891 set_bit(HCI_QUIRK_BROKEN_LOCAL_COMMANDS, &hdev->quirks);
3892 }
3893
3894 if (id->driver_info & BTUSB_INTEL_BOOT) {
3895 hdev->manufacturer = 2;
3896 set_bit(HCI_QUIRK_RAW_DEVICE, &hdev->quirks);
3897 }
3898
3899 if (id->driver_info & BTUSB_ATH3012) {
3900 data->setup_on_usb = btusb_setup_qca;
3901 hdev->set_bdaddr = btusb_set_bdaddr_ath3012;
3902 set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
3903 set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
3904 }
3905
3906 if (id->driver_info & BTUSB_QCA_ROME) {
3907 data->setup_on_usb = btusb_setup_qca;
3908 hdev->shutdown = btusb_shutdown_qca;
3909 hdev->set_bdaddr = btusb_set_bdaddr_ath3012;
3910 hdev->cmd_timeout = btusb_qca_cmd_timeout;
3911 set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
3912 btusb_check_needs_reset_resume(intf);
3913 }
3914
3915 if (id->driver_info & BTUSB_QCA_WCN6855) {
3916 data->qca_dump.id_vendor = id->idVendor;
3917 data->qca_dump.id_product = id->idProduct;
3918 data->recv_event = btusb_recv_evt_qca;
3919 data->recv_acl = btusb_recv_acl_qca;
3920 hci_devcd_register(hdev, btusb_coredump_qca, btusb_dump_hdr_qca, NULL);
3921 data->setup_on_usb = btusb_setup_qca;
3922 hdev->shutdown = btusb_shutdown_qca;
3923 hdev->set_bdaddr = btusb_set_bdaddr_wcn6855;
3924 hdev->cmd_timeout = btusb_qca_cmd_timeout;
3925 set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
3926 hci_set_msft_opcode(hdev, 0xFD70);
3927 }
3928
3929 if (id->driver_info & BTUSB_AMP) {
3930 /* AMP controllers do not support SCO packets */
3931 data->isoc = NULL;
3932 } else {
3933 /* Interface orders are hardcoded in the specification */
3934 data->isoc = usb_ifnum_to_if(data->udev, ifnum_base + 1);
3935 data->isoc_ifnum = ifnum_base + 1;
3936 }
3937
3938 if (IS_ENABLED(CONFIG_BT_HCIBTUSB_RTL) &&
3939 (id->driver_info & BTUSB_REALTEK)) {
3940 btrtl_set_driver_name(hdev, btusb_driver.name);
3941 hdev->setup = btusb_setup_realtek;
3942 hdev->shutdown = btrtl_shutdown_realtek;
3943 hdev->cmd_timeout = btusb_rtl_cmd_timeout;
3944 hdev->hw_error = btusb_rtl_hw_error;
3945
3946 /* Realtek devices need to set remote wakeup on auto-suspend */
3947 set_bit(BTUSB_WAKEUP_AUTOSUSPEND, &data->flags);
3948 set_bit(BTUSB_USE_ALT3_FOR_WBS, &data->flags);
3949 }
3950
3951 if (id->driver_info & BTUSB_ACTIONS_SEMI) {
3952 /* Support is advertised, but not implemented */
3953 set_bit(HCI_QUIRK_BROKEN_ERR_DATA_REPORTING, &hdev->quirks);
3954 set_bit(HCI_QUIRK_BROKEN_READ_TRANSMIT_POWER, &hdev->quirks);
3955 set_bit(HCI_QUIRK_BROKEN_SET_RPA_TIMEOUT, &hdev->quirks);
3956 set_bit(HCI_QUIRK_BROKEN_EXT_SCAN, &hdev->quirks);
3957 set_bit(HCI_QUIRK_BROKEN_READ_ENC_KEY_SIZE, &hdev->quirks);
3958 set_bit(HCI_QUIRK_BROKEN_EXT_CREATE_CONN, &hdev->quirks);
3959 set_bit(HCI_QUIRK_BROKEN_WRITE_AUTH_PAYLOAD_TIMEOUT, &hdev->quirks);
3960 }
3961
3962 if (!reset)
3963 set_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
3964
3965 if (force_scofix || id->driver_info & BTUSB_WRONG_SCO_MTU) {
3966 if (!disable_scofix)
3967 set_bit(HCI_QUIRK_FIXUP_BUFFER_SIZE, &hdev->quirks);
3968 }
3969
3970 if (id->driver_info & BTUSB_BROKEN_ISOC)
3971 data->isoc = NULL;
3972
3973 if (id->driver_info & BTUSB_WIDEBAND_SPEECH)
3974 set_bit(HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED, &hdev->quirks);
3975
3976 if (id->driver_info & BTUSB_INVALID_LE_STATES)
3977 set_bit(HCI_QUIRK_BROKEN_LE_STATES, &hdev->quirks);
3978
3979 if (id->driver_info & BTUSB_DIGIANSWER) {
3980 data->cmdreq_type = USB_TYPE_VENDOR;
3981 set_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
3982 }
3983
3984 if (id->driver_info & BTUSB_CSR) {
3985 struct usb_device *udev = data->udev;
3986 u16 bcdDevice = le16_to_cpu(udev->descriptor.bcdDevice);
3987
3988 /* Old firmware would otherwise execute USB reset */
3989 if (bcdDevice < 0x117)
3990 set_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
3991
3992 /* This must be set first in case we disable it for fakes */
3993 set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
3994
3995 /* Fake CSR devices with broken commands */
3996 if (le16_to_cpu(udev->descriptor.idVendor) == 0x0a12 &&
3997 le16_to_cpu(udev->descriptor.idProduct) == 0x0001)
3998 hdev->setup = btusb_setup_csr;
3999 }
4000
4001 if (id->driver_info & BTUSB_SNIFFER) {
4002 struct usb_device *udev = data->udev;
4003
4004 /* New sniffer firmware has crippled HCI interface */
4005 if (le16_to_cpu(udev->descriptor.bcdDevice) > 0x997)
4006 set_bit(HCI_QUIRK_RAW_DEVICE, &hdev->quirks);
4007 }
4008
4009 if (id->driver_info & BTUSB_INTEL_BOOT) {
4010 /* A bug in the bootloader causes that interrupt interface is
4011 * only enabled after receiving SetInterface(0, AltSetting=0).
4012 */
4013 err = usb_set_interface(data->udev, 0, 0);
4014 if (err < 0) {
4015 BT_ERR("failed to set interface 0, alt 0 %d", err);
4016 goto out_free_dev;
4017 }
4018 }
4019
4020 if (data->isoc) {
4021 err = usb_driver_claim_interface(&btusb_driver,
4022 data->isoc, data);
4023 if (err < 0)
4024 goto out_free_dev;
4025 }
4026
4027 if (IS_ENABLED(CONFIG_BT_HCIBTUSB_BCM) && data->diag) {
4028 if (!usb_driver_claim_interface(&btusb_driver,
4029 data->diag, data))
4030 __set_diag_interface(hdev);
4031 else
4032 data->diag = NULL;
4033 }
4034
4035 if (enable_autosuspend)
4036 usb_enable_autosuspend(data->udev);
4037
4038 data->poll_sync = enable_poll_sync;
4039
4040 err = hci_register_dev(hdev);
4041 if (err < 0)
4042 goto out_free_dev;
4043
4044 usb_set_intfdata(intf, data);
4045
4046 debugfs_create_file("force_poll_sync", 0644, hdev->debugfs, data,
4047 &force_poll_sync_fops);
4048
4049 return 0;
4050
4051out_free_dev:
4052 if (data->reset_gpio)
4053 gpiod_put(data->reset_gpio);
4054 hci_free_dev(hdev);
4055 return err;
4056}
4057
4058static void btusb_disconnect(struct usb_interface *intf)
4059{
4060 struct btusb_data *data = usb_get_intfdata(intf);
4061 struct hci_dev *hdev;
4062
4063 BT_DBG("intf %p", intf);
4064
4065 if (!data)
4066 return;
4067
4068 hdev = data->hdev;
4069 usb_set_intfdata(data->intf, NULL);
4070
4071 if (data->isoc)
4072 usb_set_intfdata(data->isoc, NULL);
4073
4074 if (data->diag)
4075 usb_set_intfdata(data->diag, NULL);
4076
4077 if (data->disconnect)
4078 data->disconnect(hdev);
4079
4080 hci_unregister_dev(hdev);
4081
4082 if (intf == data->intf) {
4083 if (data->isoc)
4084 usb_driver_release_interface(&btusb_driver, data->isoc);
4085 if (data->diag)
4086 usb_driver_release_interface(&btusb_driver, data->diag);
4087 } else if (intf == data->isoc) {
4088 if (data->diag)
4089 usb_driver_release_interface(&btusb_driver, data->diag);
4090 usb_driver_release_interface(&btusb_driver, data->intf);
4091 } else if (intf == data->diag) {
4092 usb_driver_release_interface(&btusb_driver, data->intf);
4093 if (data->isoc)
4094 usb_driver_release_interface(&btusb_driver, data->isoc);
4095 }
4096
4097 if (data->oob_wake_irq)
4098 device_init_wakeup(&data->udev->dev, false);
4099
4100 if (data->reset_gpio)
4101 gpiod_put(data->reset_gpio);
4102
4103 hci_free_dev(hdev);
4104}
4105
4106#ifdef CONFIG_PM
4107static int btusb_suspend(struct usb_interface *intf, pm_message_t message)
4108{
4109 struct btusb_data *data = usb_get_intfdata(intf);
4110
4111 BT_DBG("intf %p", intf);
4112
4113 /* Don't auto-suspend if there are connections; external suspend calls
4114 * shall never fail.
4115 */
4116 if (PMSG_IS_AUTO(message) && hci_conn_count(data->hdev))
4117 return -EBUSY;
4118
4119 if (data->suspend_count++)
4120 return 0;
4121
4122 spin_lock_irq(&data->txlock);
4123 if (!(PMSG_IS_AUTO(message) && data->tx_in_flight)) {
4124 set_bit(BTUSB_SUSPENDING, &data->flags);
4125 spin_unlock_irq(&data->txlock);
4126 } else {
4127 spin_unlock_irq(&data->txlock);
4128 data->suspend_count--;
4129 return -EBUSY;
4130 }
4131
4132 cancel_work_sync(&data->work);
4133
4134 if (data->suspend)
4135 data->suspend(data->hdev);
4136
4137 btusb_stop_traffic(data);
4138 usb_kill_anchored_urbs(&data->tx_anchor);
4139
4140 if (data->oob_wake_irq && device_may_wakeup(&data->udev->dev)) {
4141 set_bit(BTUSB_OOB_WAKE_ENABLED, &data->flags);
4142 enable_irq_wake(data->oob_wake_irq);
4143 enable_irq(data->oob_wake_irq);
4144 }
4145
4146 /* For global suspend, Realtek devices lose the loaded fw
4147 * in them. But for autosuspend, firmware should remain.
4148 * Actually, it depends on whether the usb host sends
4149 * set feature (enable wakeup) or not.
4150 */
4151 if (test_bit(BTUSB_WAKEUP_AUTOSUSPEND, &data->flags)) {
4152 if (PMSG_IS_AUTO(message) &&
4153 device_can_wakeup(&data->udev->dev))
4154 data->udev->do_remote_wakeup = 1;
4155 else if (!PMSG_IS_AUTO(message) &&
4156 !device_may_wakeup(&data->udev->dev)) {
4157 data->udev->do_remote_wakeup = 0;
4158 data->udev->reset_resume = 1;
4159 }
4160 }
4161
4162 return 0;
4163}
4164
4165static void play_deferred(struct btusb_data *data)
4166{
4167 struct urb *urb;
4168 int err;
4169
4170 while ((urb = usb_get_from_anchor(&data->deferred))) {
4171 usb_anchor_urb(urb, &data->tx_anchor);
4172
4173 err = usb_submit_urb(urb, GFP_ATOMIC);
4174 if (err < 0) {
4175 if (err != -EPERM && err != -ENODEV)
4176 BT_ERR("%s urb %p submission failed (%d)",
4177 data->hdev->name, urb, -err);
4178 kfree(urb->setup_packet);
4179 usb_unanchor_urb(urb);
4180 usb_free_urb(urb);
4181 break;
4182 }
4183
4184 data->tx_in_flight++;
4185 usb_free_urb(urb);
4186 }
4187
4188 /* Cleanup the rest deferred urbs. */
4189 while ((urb = usb_get_from_anchor(&data->deferred))) {
4190 kfree(urb->setup_packet);
4191 usb_free_urb(urb);
4192 }
4193}
4194
4195static int btusb_resume(struct usb_interface *intf)
4196{
4197 struct btusb_data *data = usb_get_intfdata(intf);
4198 struct hci_dev *hdev = data->hdev;
4199 int err = 0;
4200
4201 BT_DBG("intf %p", intf);
4202
4203 if (--data->suspend_count)
4204 return 0;
4205
4206 /* Disable only if not already disabled (keep it balanced) */
4207 if (test_and_clear_bit(BTUSB_OOB_WAKE_ENABLED, &data->flags)) {
4208 disable_irq(data->oob_wake_irq);
4209 disable_irq_wake(data->oob_wake_irq);
4210 }
4211
4212 if (!test_bit(HCI_RUNNING, &hdev->flags))
4213 goto done;
4214
4215 if (test_bit(BTUSB_INTR_RUNNING, &data->flags)) {
4216 err = btusb_submit_intr_urb(hdev, GFP_NOIO);
4217 if (err < 0) {
4218 clear_bit(BTUSB_INTR_RUNNING, &data->flags);
4219 goto failed;
4220 }
4221 }
4222
4223 if (test_bit(BTUSB_BULK_RUNNING, &data->flags)) {
4224 err = btusb_submit_bulk_urb(hdev, GFP_NOIO);
4225 if (err < 0) {
4226 clear_bit(BTUSB_BULK_RUNNING, &data->flags);
4227 goto failed;
4228 }
4229
4230 btusb_submit_bulk_urb(hdev, GFP_NOIO);
4231 }
4232
4233 if (test_bit(BTUSB_ISOC_RUNNING, &data->flags)) {
4234 if (btusb_submit_isoc_urb(hdev, GFP_NOIO) < 0)
4235 clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
4236 else
4237 btusb_submit_isoc_urb(hdev, GFP_NOIO);
4238 }
4239
4240 if (data->resume)
4241 data->resume(hdev);
4242
4243 spin_lock_irq(&data->txlock);
4244 play_deferred(data);
4245 clear_bit(BTUSB_SUSPENDING, &data->flags);
4246 spin_unlock_irq(&data->txlock);
4247 schedule_work(&data->work);
4248
4249 return 0;
4250
4251failed:
4252 usb_scuttle_anchored_urbs(&data->deferred);
4253done:
4254 spin_lock_irq(&data->txlock);
4255 clear_bit(BTUSB_SUSPENDING, &data->flags);
4256 spin_unlock_irq(&data->txlock);
4257
4258 return err;
4259}
4260#endif
4261
4262#ifdef CONFIG_DEV_COREDUMP
4263static void btusb_coredump(struct device *dev)
4264{
4265 struct btusb_data *data = dev_get_drvdata(dev);
4266 struct hci_dev *hdev = data->hdev;
4267
4268 if (hdev->dump.coredump)
4269 hdev->dump.coredump(hdev);
4270}
4271#endif
4272
4273static struct usb_driver btusb_driver = {
4274 .name = "btusb",
4275 .probe = btusb_probe,
4276 .disconnect = btusb_disconnect,
4277#ifdef CONFIG_PM
4278 .suspend = btusb_suspend,
4279 .resume = btusb_resume,
4280#endif
4281 .id_table = btusb_table,
4282 .supports_autosuspend = 1,
4283 .disable_hub_initiated_lpm = 1,
4284
4285#ifdef CONFIG_DEV_COREDUMP
4286 .driver = {
4287 .coredump = btusb_coredump,
4288 },
4289#endif
4290};
4291
4292module_usb_driver(btusb_driver);
4293
4294module_param(disable_scofix, bool, 0644);
4295MODULE_PARM_DESC(disable_scofix, "Disable fixup of wrong SCO buffer size");
4296
4297module_param(force_scofix, bool, 0644);
4298MODULE_PARM_DESC(force_scofix, "Force fixup of wrong SCO buffers size");
4299
4300module_param(enable_autosuspend, bool, 0644);
4301MODULE_PARM_DESC(enable_autosuspend, "Enable USB autosuspend by default");
4302
4303module_param(reset, bool, 0644);
4304MODULE_PARM_DESC(reset, "Send HCI reset command on initialization");
4305
4306MODULE_AUTHOR("Marcel Holtmann <marcel@holtmann.org>");
4307MODULE_DESCRIPTION("Generic Bluetooth USB driver ver " VERSION);
4308MODULE_VERSION(VERSION);
4309MODULE_LICENSE("GPL");
1/*
2 *
3 * Generic Bluetooth USB driver
4 *
5 * Copyright (C) 2005-2008 Marcel Holtmann <marcel@holtmann.org>
6 *
7 *
8 * This program is free software; you can redistribute it and/or modify
9 * it under the terms of the GNU General Public License as published by
10 * the Free Software Foundation; either version 2 of the License, or
11 * (at your option) any later version.
12 *
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
21 *
22 */
23
24#include <linux/module.h>
25#include <linux/usb.h>
26#include <linux/firmware.h>
27#include <asm/unaligned.h>
28
29#include <net/bluetooth/bluetooth.h>
30#include <net/bluetooth/hci_core.h>
31
32#include "btintel.h"
33#include "btbcm.h"
34#include "btrtl.h"
35
36#define VERSION "0.8"
37
38static bool disable_scofix;
39static bool force_scofix;
40
41static bool reset = true;
42
43static struct usb_driver btusb_driver;
44
45#define BTUSB_IGNORE 0x01
46#define BTUSB_DIGIANSWER 0x02
47#define BTUSB_CSR 0x04
48#define BTUSB_SNIFFER 0x08
49#define BTUSB_BCM92035 0x10
50#define BTUSB_BROKEN_ISOC 0x20
51#define BTUSB_WRONG_SCO_MTU 0x40
52#define BTUSB_ATH3012 0x80
53#define BTUSB_INTEL 0x100
54#define BTUSB_INTEL_BOOT 0x200
55#define BTUSB_BCM_PATCHRAM 0x400
56#define BTUSB_MARVELL 0x800
57#define BTUSB_SWAVE 0x1000
58#define BTUSB_INTEL_NEW 0x2000
59#define BTUSB_AMP 0x4000
60#define BTUSB_QCA_ROME 0x8000
61#define BTUSB_BCM_APPLE 0x10000
62#define BTUSB_REALTEK 0x20000
63#define BTUSB_BCM2045 0x40000
64#define BTUSB_IFNUM_2 0x80000
65
66static const struct usb_device_id btusb_table[] = {
67 /* Generic Bluetooth USB device */
68 { USB_DEVICE_INFO(0xe0, 0x01, 0x01) },
69
70 /* Generic Bluetooth AMP device */
71 { USB_DEVICE_INFO(0xe0, 0x01, 0x04), .driver_info = BTUSB_AMP },
72
73 /* Generic Bluetooth USB interface */
74 { USB_INTERFACE_INFO(0xe0, 0x01, 0x01) },
75
76 /* Apple-specific (Broadcom) devices */
77 { USB_VENDOR_AND_INTERFACE_INFO(0x05ac, 0xff, 0x01, 0x01),
78 .driver_info = BTUSB_BCM_APPLE | BTUSB_IFNUM_2 },
79
80 /* MediaTek MT76x0E */
81 { USB_DEVICE(0x0e8d, 0x763f) },
82
83 /* Broadcom SoftSailing reporting vendor specific */
84 { USB_DEVICE(0x0a5c, 0x21e1) },
85
86 /* Apple MacBookPro 7,1 */
87 { USB_DEVICE(0x05ac, 0x8213) },
88
89 /* Apple iMac11,1 */
90 { USB_DEVICE(0x05ac, 0x8215) },
91
92 /* Apple MacBookPro6,2 */
93 { USB_DEVICE(0x05ac, 0x8218) },
94
95 /* Apple MacBookAir3,1, MacBookAir3,2 */
96 { USB_DEVICE(0x05ac, 0x821b) },
97
98 /* Apple MacBookAir4,1 */
99 { USB_DEVICE(0x05ac, 0x821f) },
100
101 /* Apple MacBookPro8,2 */
102 { USB_DEVICE(0x05ac, 0x821a) },
103
104 /* Apple MacMini5,1 */
105 { USB_DEVICE(0x05ac, 0x8281) },
106
107 /* AVM BlueFRITZ! USB v2.0 */
108 { USB_DEVICE(0x057c, 0x3800), .driver_info = BTUSB_SWAVE },
109
110 /* Bluetooth Ultraport Module from IBM */
111 { USB_DEVICE(0x04bf, 0x030a) },
112
113 /* ALPS Modules with non-standard id */
114 { USB_DEVICE(0x044e, 0x3001) },
115 { USB_DEVICE(0x044e, 0x3002) },
116
117 /* Ericsson with non-standard id */
118 { USB_DEVICE(0x0bdb, 0x1002) },
119
120 /* Canyon CN-BTU1 with HID interfaces */
121 { USB_DEVICE(0x0c10, 0x0000) },
122
123 /* Broadcom BCM20702A0 */
124 { USB_DEVICE(0x413c, 0x8197) },
125
126 /* Broadcom BCM20702B0 (Dynex/Insignia) */
127 { USB_DEVICE(0x19ff, 0x0239), .driver_info = BTUSB_BCM_PATCHRAM },
128
129 /* Broadcom BCM43142A0 (Foxconn/Lenovo) */
130 { USB_DEVICE(0x105b, 0xe065), .driver_info = BTUSB_BCM_PATCHRAM },
131
132 /* Foxconn - Hon Hai */
133 { USB_VENDOR_AND_INTERFACE_INFO(0x0489, 0xff, 0x01, 0x01),
134 .driver_info = BTUSB_BCM_PATCHRAM },
135
136 /* Lite-On Technology - Broadcom based */
137 { USB_VENDOR_AND_INTERFACE_INFO(0x04ca, 0xff, 0x01, 0x01),
138 .driver_info = BTUSB_BCM_PATCHRAM },
139
140 /* Broadcom devices with vendor specific id */
141 { USB_VENDOR_AND_INTERFACE_INFO(0x0a5c, 0xff, 0x01, 0x01),
142 .driver_info = BTUSB_BCM_PATCHRAM },
143
144 /* ASUSTek Computer - Broadcom based */
145 { USB_VENDOR_AND_INTERFACE_INFO(0x0b05, 0xff, 0x01, 0x01),
146 .driver_info = BTUSB_BCM_PATCHRAM },
147
148 /* Belkin F8065bf - Broadcom based */
149 { USB_VENDOR_AND_INTERFACE_INFO(0x050d, 0xff, 0x01, 0x01),
150 .driver_info = BTUSB_BCM_PATCHRAM },
151
152 /* IMC Networks - Broadcom based */
153 { USB_VENDOR_AND_INTERFACE_INFO(0x13d3, 0xff, 0x01, 0x01),
154 .driver_info = BTUSB_BCM_PATCHRAM },
155
156 /* Toshiba Corp - Broadcom based */
157 { USB_VENDOR_AND_INTERFACE_INFO(0x0930, 0xff, 0x01, 0x01),
158 .driver_info = BTUSB_BCM_PATCHRAM },
159
160 /* Intel Bluetooth USB Bootloader (RAM module) */
161 { USB_DEVICE(0x8087, 0x0a5a),
162 .driver_info = BTUSB_INTEL_BOOT | BTUSB_BROKEN_ISOC },
163
164 { } /* Terminating entry */
165};
166
167MODULE_DEVICE_TABLE(usb, btusb_table);
168
169static const struct usb_device_id blacklist_table[] = {
170 /* CSR BlueCore devices */
171 { USB_DEVICE(0x0a12, 0x0001), .driver_info = BTUSB_CSR },
172
173 /* Broadcom BCM2033 without firmware */
174 { USB_DEVICE(0x0a5c, 0x2033), .driver_info = BTUSB_IGNORE },
175
176 /* Broadcom BCM2045 devices */
177 { USB_DEVICE(0x0a5c, 0x2045), .driver_info = BTUSB_BCM2045 },
178
179 /* Atheros 3011 with sflash firmware */
180 { USB_DEVICE(0x0489, 0xe027), .driver_info = BTUSB_IGNORE },
181 { USB_DEVICE(0x0489, 0xe03d), .driver_info = BTUSB_IGNORE },
182 { USB_DEVICE(0x04f2, 0xaff1), .driver_info = BTUSB_IGNORE },
183 { USB_DEVICE(0x0930, 0x0215), .driver_info = BTUSB_IGNORE },
184 { USB_DEVICE(0x0cf3, 0x3002), .driver_info = BTUSB_IGNORE },
185 { USB_DEVICE(0x0cf3, 0xe019), .driver_info = BTUSB_IGNORE },
186 { USB_DEVICE(0x13d3, 0x3304), .driver_info = BTUSB_IGNORE },
187
188 /* Atheros AR9285 Malbec with sflash firmware */
189 { USB_DEVICE(0x03f0, 0x311d), .driver_info = BTUSB_IGNORE },
190
191 /* Atheros 3012 with sflash firmware */
192 { USB_DEVICE(0x0489, 0xe04d), .driver_info = BTUSB_ATH3012 },
193 { USB_DEVICE(0x0489, 0xe04e), .driver_info = BTUSB_ATH3012 },
194 { USB_DEVICE(0x0489, 0xe056), .driver_info = BTUSB_ATH3012 },
195 { USB_DEVICE(0x0489, 0xe057), .driver_info = BTUSB_ATH3012 },
196 { USB_DEVICE(0x0489, 0xe05f), .driver_info = BTUSB_ATH3012 },
197 { USB_DEVICE(0x0489, 0xe076), .driver_info = BTUSB_ATH3012 },
198 { USB_DEVICE(0x0489, 0xe078), .driver_info = BTUSB_ATH3012 },
199 { USB_DEVICE(0x0489, 0xe095), .driver_info = BTUSB_ATH3012 },
200 { USB_DEVICE(0x04c5, 0x1330), .driver_info = BTUSB_ATH3012 },
201 { USB_DEVICE(0x04ca, 0x3004), .driver_info = BTUSB_ATH3012 },
202 { USB_DEVICE(0x04ca, 0x3005), .driver_info = BTUSB_ATH3012 },
203 { USB_DEVICE(0x04ca, 0x3006), .driver_info = BTUSB_ATH3012 },
204 { USB_DEVICE(0x04ca, 0x3007), .driver_info = BTUSB_ATH3012 },
205 { USB_DEVICE(0x04ca, 0x3008), .driver_info = BTUSB_ATH3012 },
206 { USB_DEVICE(0x04ca, 0x300b), .driver_info = BTUSB_ATH3012 },
207 { USB_DEVICE(0x04ca, 0x300d), .driver_info = BTUSB_ATH3012 },
208 { USB_DEVICE(0x04ca, 0x300f), .driver_info = BTUSB_ATH3012 },
209 { USB_DEVICE(0x04ca, 0x3010), .driver_info = BTUSB_ATH3012 },
210 { USB_DEVICE(0x04ca, 0x3014), .driver_info = BTUSB_ATH3012 },
211 { USB_DEVICE(0x0930, 0x0219), .driver_info = BTUSB_ATH3012 },
212 { USB_DEVICE(0x0930, 0x021c), .driver_info = BTUSB_ATH3012 },
213 { USB_DEVICE(0x0930, 0x0220), .driver_info = BTUSB_ATH3012 },
214 { USB_DEVICE(0x0930, 0x0227), .driver_info = BTUSB_ATH3012 },
215 { USB_DEVICE(0x0b05, 0x17d0), .driver_info = BTUSB_ATH3012 },
216 { USB_DEVICE(0x0cf3, 0x0036), .driver_info = BTUSB_ATH3012 },
217 { USB_DEVICE(0x0cf3, 0x3004), .driver_info = BTUSB_ATH3012 },
218 { USB_DEVICE(0x0cf3, 0x3008), .driver_info = BTUSB_ATH3012 },
219 { USB_DEVICE(0x0cf3, 0x311d), .driver_info = BTUSB_ATH3012 },
220 { USB_DEVICE(0x0cf3, 0x311e), .driver_info = BTUSB_ATH3012 },
221 { USB_DEVICE(0x0cf3, 0x311f), .driver_info = BTUSB_ATH3012 },
222 { USB_DEVICE(0x0cf3, 0x3121), .driver_info = BTUSB_ATH3012 },
223 { USB_DEVICE(0x0cf3, 0x817a), .driver_info = BTUSB_ATH3012 },
224 { USB_DEVICE(0x0cf3, 0x817b), .driver_info = BTUSB_ATH3012 },
225 { USB_DEVICE(0x0cf3, 0xe003), .driver_info = BTUSB_ATH3012 },
226 { USB_DEVICE(0x0cf3, 0xe004), .driver_info = BTUSB_ATH3012 },
227 { USB_DEVICE(0x0cf3, 0xe005), .driver_info = BTUSB_ATH3012 },
228 { USB_DEVICE(0x0cf3, 0xe006), .driver_info = BTUSB_ATH3012 },
229 { USB_DEVICE(0x13d3, 0x3362), .driver_info = BTUSB_ATH3012 },
230 { USB_DEVICE(0x13d3, 0x3375), .driver_info = BTUSB_ATH3012 },
231 { USB_DEVICE(0x13d3, 0x3393), .driver_info = BTUSB_ATH3012 },
232 { USB_DEVICE(0x13d3, 0x3395), .driver_info = BTUSB_ATH3012 },
233 { USB_DEVICE(0x13d3, 0x3402), .driver_info = BTUSB_ATH3012 },
234 { USB_DEVICE(0x13d3, 0x3408), .driver_info = BTUSB_ATH3012 },
235 { USB_DEVICE(0x13d3, 0x3423), .driver_info = BTUSB_ATH3012 },
236 { USB_DEVICE(0x13d3, 0x3432), .driver_info = BTUSB_ATH3012 },
237 { USB_DEVICE(0x13d3, 0x3472), .driver_info = BTUSB_ATH3012 },
238 { USB_DEVICE(0x13d3, 0x3474), .driver_info = BTUSB_ATH3012 },
239
240 /* Atheros AR5BBU12 with sflash firmware */
241 { USB_DEVICE(0x0489, 0xe02c), .driver_info = BTUSB_IGNORE },
242
243 /* Atheros AR5BBU12 with sflash firmware */
244 { USB_DEVICE(0x0489, 0xe036), .driver_info = BTUSB_ATH3012 },
245 { USB_DEVICE(0x0489, 0xe03c), .driver_info = BTUSB_ATH3012 },
246
247 /* QCA ROME chipset */
248 { USB_DEVICE(0x0cf3, 0xe007), .driver_info = BTUSB_QCA_ROME },
249 { USB_DEVICE(0x0cf3, 0xe300), .driver_info = BTUSB_QCA_ROME },
250 { USB_DEVICE(0x0cf3, 0xe360), .driver_info = BTUSB_QCA_ROME },
251
252 /* Broadcom BCM2035 */
253 { USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 },
254 { USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU },
255 { USB_DEVICE(0x0a5c, 0x2035), .driver_info = BTUSB_WRONG_SCO_MTU },
256
257 /* Broadcom BCM2045 */
258 { USB_DEVICE(0x0a5c, 0x2039), .driver_info = BTUSB_WRONG_SCO_MTU },
259 { USB_DEVICE(0x0a5c, 0x2101), .driver_info = BTUSB_WRONG_SCO_MTU },
260
261 /* IBM/Lenovo ThinkPad with Broadcom chip */
262 { USB_DEVICE(0x0a5c, 0x201e), .driver_info = BTUSB_WRONG_SCO_MTU },
263 { USB_DEVICE(0x0a5c, 0x2110), .driver_info = BTUSB_WRONG_SCO_MTU },
264
265 /* HP laptop with Broadcom chip */
266 { USB_DEVICE(0x03f0, 0x171d), .driver_info = BTUSB_WRONG_SCO_MTU },
267
268 /* Dell laptop with Broadcom chip */
269 { USB_DEVICE(0x413c, 0x8126), .driver_info = BTUSB_WRONG_SCO_MTU },
270
271 /* Dell Wireless 370 and 410 devices */
272 { USB_DEVICE(0x413c, 0x8152), .driver_info = BTUSB_WRONG_SCO_MTU },
273 { USB_DEVICE(0x413c, 0x8156), .driver_info = BTUSB_WRONG_SCO_MTU },
274
275 /* Belkin F8T012 and F8T013 devices */
276 { USB_DEVICE(0x050d, 0x0012), .driver_info = BTUSB_WRONG_SCO_MTU },
277 { USB_DEVICE(0x050d, 0x0013), .driver_info = BTUSB_WRONG_SCO_MTU },
278
279 /* Asus WL-BTD202 device */
280 { USB_DEVICE(0x0b05, 0x1715), .driver_info = BTUSB_WRONG_SCO_MTU },
281
282 /* Kensington Bluetooth USB adapter */
283 { USB_DEVICE(0x047d, 0x105e), .driver_info = BTUSB_WRONG_SCO_MTU },
284
285 /* RTX Telecom based adapters with buggy SCO support */
286 { USB_DEVICE(0x0400, 0x0807), .driver_info = BTUSB_BROKEN_ISOC },
287 { USB_DEVICE(0x0400, 0x080a), .driver_info = BTUSB_BROKEN_ISOC },
288
289 /* CONWISE Technology based adapters with buggy SCO support */
290 { USB_DEVICE(0x0e5e, 0x6622), .driver_info = BTUSB_BROKEN_ISOC },
291
292 /* Roper Class 1 Bluetooth Dongle (Silicon Wave based) */
293 { USB_DEVICE(0x1310, 0x0001), .driver_info = BTUSB_SWAVE },
294
295 /* Digianswer devices */
296 { USB_DEVICE(0x08fd, 0x0001), .driver_info = BTUSB_DIGIANSWER },
297 { USB_DEVICE(0x08fd, 0x0002), .driver_info = BTUSB_IGNORE },
298
299 /* CSR BlueCore Bluetooth Sniffer */
300 { USB_DEVICE(0x0a12, 0x0002),
301 .driver_info = BTUSB_SNIFFER | BTUSB_BROKEN_ISOC },
302
303 /* Frontline ComProbe Bluetooth Sniffer */
304 { USB_DEVICE(0x16d3, 0x0002),
305 .driver_info = BTUSB_SNIFFER | BTUSB_BROKEN_ISOC },
306
307 /* Marvell Bluetooth devices */
308 { USB_DEVICE(0x1286, 0x2044), .driver_info = BTUSB_MARVELL },
309 { USB_DEVICE(0x1286, 0x2046), .driver_info = BTUSB_MARVELL },
310
311 /* Intel Bluetooth devices */
312 { USB_DEVICE(0x8087, 0x07da), .driver_info = BTUSB_CSR },
313 { USB_DEVICE(0x8087, 0x07dc), .driver_info = BTUSB_INTEL },
314 { USB_DEVICE(0x8087, 0x0a2a), .driver_info = BTUSB_INTEL },
315 { USB_DEVICE(0x8087, 0x0a2b), .driver_info = BTUSB_INTEL_NEW },
316
317 /* Other Intel Bluetooth devices */
318 { USB_VENDOR_AND_INTERFACE_INFO(0x8087, 0xe0, 0x01, 0x01),
319 .driver_info = BTUSB_IGNORE },
320
321 /* Realtek Bluetooth devices */
322 { USB_VENDOR_AND_INTERFACE_INFO(0x0bda, 0xe0, 0x01, 0x01),
323 .driver_info = BTUSB_REALTEK },
324
325 /* Additional Realtek 8723AE Bluetooth devices */
326 { USB_DEVICE(0x0930, 0x021d), .driver_info = BTUSB_REALTEK },
327 { USB_DEVICE(0x13d3, 0x3394), .driver_info = BTUSB_REALTEK },
328
329 /* Additional Realtek 8723BE Bluetooth devices */
330 { USB_DEVICE(0x0489, 0xe085), .driver_info = BTUSB_REALTEK },
331 { USB_DEVICE(0x0489, 0xe08b), .driver_info = BTUSB_REALTEK },
332 { USB_DEVICE(0x13d3, 0x3410), .driver_info = BTUSB_REALTEK },
333 { USB_DEVICE(0x13d3, 0x3416), .driver_info = BTUSB_REALTEK },
334 { USB_DEVICE(0x13d3, 0x3459), .driver_info = BTUSB_REALTEK },
335
336 /* Additional Realtek 8821AE Bluetooth devices */
337 { USB_DEVICE(0x0b05, 0x17dc), .driver_info = BTUSB_REALTEK },
338 { USB_DEVICE(0x13d3, 0x3414), .driver_info = BTUSB_REALTEK },
339 { USB_DEVICE(0x13d3, 0x3458), .driver_info = BTUSB_REALTEK },
340 { USB_DEVICE(0x13d3, 0x3461), .driver_info = BTUSB_REALTEK },
341 { USB_DEVICE(0x13d3, 0x3462), .driver_info = BTUSB_REALTEK },
342
343 /* Silicon Wave based devices */
344 { USB_DEVICE(0x0c10, 0x0000), .driver_info = BTUSB_SWAVE },
345
346 { } /* Terminating entry */
347};
348
349#define BTUSB_MAX_ISOC_FRAMES 10
350
351#define BTUSB_INTR_RUNNING 0
352#define BTUSB_BULK_RUNNING 1
353#define BTUSB_ISOC_RUNNING 2
354#define BTUSB_SUSPENDING 3
355#define BTUSB_DID_ISO_RESUME 4
356#define BTUSB_BOOTLOADER 5
357#define BTUSB_DOWNLOADING 6
358#define BTUSB_FIRMWARE_LOADED 7
359#define BTUSB_FIRMWARE_FAILED 8
360#define BTUSB_BOOTING 9
361#define BTUSB_RESET_RESUME 10
362#define BTUSB_DIAG_RUNNING 11
363
364struct btusb_data {
365 struct hci_dev *hdev;
366 struct usb_device *udev;
367 struct usb_interface *intf;
368 struct usb_interface *isoc;
369 struct usb_interface *diag;
370
371 unsigned long flags;
372
373 struct work_struct work;
374 struct work_struct waker;
375
376 struct usb_anchor deferred;
377 struct usb_anchor tx_anchor;
378 int tx_in_flight;
379 spinlock_t txlock;
380
381 struct usb_anchor intr_anchor;
382 struct usb_anchor bulk_anchor;
383 struct usb_anchor isoc_anchor;
384 struct usb_anchor diag_anchor;
385 spinlock_t rxlock;
386
387 struct sk_buff *evt_skb;
388 struct sk_buff *acl_skb;
389 struct sk_buff *sco_skb;
390
391 struct usb_endpoint_descriptor *intr_ep;
392 struct usb_endpoint_descriptor *bulk_tx_ep;
393 struct usb_endpoint_descriptor *bulk_rx_ep;
394 struct usb_endpoint_descriptor *isoc_tx_ep;
395 struct usb_endpoint_descriptor *isoc_rx_ep;
396 struct usb_endpoint_descriptor *diag_tx_ep;
397 struct usb_endpoint_descriptor *diag_rx_ep;
398
399 __u8 cmdreq_type;
400 __u8 cmdreq;
401
402 unsigned int sco_num;
403 int isoc_altsetting;
404 int suspend_count;
405
406 int (*recv_event)(struct hci_dev *hdev, struct sk_buff *skb);
407 int (*recv_bulk)(struct btusb_data *data, void *buffer, int count);
408
409 int (*setup_on_usb)(struct hci_dev *hdev);
410};
411
412static inline void btusb_free_frags(struct btusb_data *data)
413{
414 unsigned long flags;
415
416 spin_lock_irqsave(&data->rxlock, flags);
417
418 kfree_skb(data->evt_skb);
419 data->evt_skb = NULL;
420
421 kfree_skb(data->acl_skb);
422 data->acl_skb = NULL;
423
424 kfree_skb(data->sco_skb);
425 data->sco_skb = NULL;
426
427 spin_unlock_irqrestore(&data->rxlock, flags);
428}
429
430static int btusb_recv_intr(struct btusb_data *data, void *buffer, int count)
431{
432 struct sk_buff *skb;
433 int err = 0;
434
435 spin_lock(&data->rxlock);
436 skb = data->evt_skb;
437
438 while (count) {
439 int len;
440
441 if (!skb) {
442 skb = bt_skb_alloc(HCI_MAX_EVENT_SIZE, GFP_ATOMIC);
443 if (!skb) {
444 err = -ENOMEM;
445 break;
446 }
447
448 hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
449 hci_skb_expect(skb) = HCI_EVENT_HDR_SIZE;
450 }
451
452 len = min_t(uint, hci_skb_expect(skb), count);
453 memcpy(skb_put(skb, len), buffer, len);
454
455 count -= len;
456 buffer += len;
457 hci_skb_expect(skb) -= len;
458
459 if (skb->len == HCI_EVENT_HDR_SIZE) {
460 /* Complete event header */
461 hci_skb_expect(skb) = hci_event_hdr(skb)->plen;
462
463 if (skb_tailroom(skb) < hci_skb_expect(skb)) {
464 kfree_skb(skb);
465 skb = NULL;
466
467 err = -EILSEQ;
468 break;
469 }
470 }
471
472 if (!hci_skb_expect(skb)) {
473 /* Complete frame */
474 data->recv_event(data->hdev, skb);
475 skb = NULL;
476 }
477 }
478
479 data->evt_skb = skb;
480 spin_unlock(&data->rxlock);
481
482 return err;
483}
484
485static int btusb_recv_bulk(struct btusb_data *data, void *buffer, int count)
486{
487 struct sk_buff *skb;
488 int err = 0;
489
490 spin_lock(&data->rxlock);
491 skb = data->acl_skb;
492
493 while (count) {
494 int len;
495
496 if (!skb) {
497 skb = bt_skb_alloc(HCI_MAX_FRAME_SIZE, GFP_ATOMIC);
498 if (!skb) {
499 err = -ENOMEM;
500 break;
501 }
502
503 hci_skb_pkt_type(skb) = HCI_ACLDATA_PKT;
504 hci_skb_expect(skb) = HCI_ACL_HDR_SIZE;
505 }
506
507 len = min_t(uint, hci_skb_expect(skb), count);
508 memcpy(skb_put(skb, len), buffer, len);
509
510 count -= len;
511 buffer += len;
512 hci_skb_expect(skb) -= len;
513
514 if (skb->len == HCI_ACL_HDR_SIZE) {
515 __le16 dlen = hci_acl_hdr(skb)->dlen;
516
517 /* Complete ACL header */
518 hci_skb_expect(skb) = __le16_to_cpu(dlen);
519
520 if (skb_tailroom(skb) < hci_skb_expect(skb)) {
521 kfree_skb(skb);
522 skb = NULL;
523
524 err = -EILSEQ;
525 break;
526 }
527 }
528
529 if (!hci_skb_expect(skb)) {
530 /* Complete frame */
531 hci_recv_frame(data->hdev, skb);
532 skb = NULL;
533 }
534 }
535
536 data->acl_skb = skb;
537 spin_unlock(&data->rxlock);
538
539 return err;
540}
541
542static int btusb_recv_isoc(struct btusb_data *data, void *buffer, int count)
543{
544 struct sk_buff *skb;
545 int err = 0;
546
547 spin_lock(&data->rxlock);
548 skb = data->sco_skb;
549
550 while (count) {
551 int len;
552
553 if (!skb) {
554 skb = bt_skb_alloc(HCI_MAX_SCO_SIZE, GFP_ATOMIC);
555 if (!skb) {
556 err = -ENOMEM;
557 break;
558 }
559
560 hci_skb_pkt_type(skb) = HCI_SCODATA_PKT;
561 hci_skb_expect(skb) = HCI_SCO_HDR_SIZE;
562 }
563
564 len = min_t(uint, hci_skb_expect(skb), count);
565 memcpy(skb_put(skb, len), buffer, len);
566
567 count -= len;
568 buffer += len;
569 hci_skb_expect(skb) -= len;
570
571 if (skb->len == HCI_SCO_HDR_SIZE) {
572 /* Complete SCO header */
573 hci_skb_expect(skb) = hci_sco_hdr(skb)->dlen;
574
575 if (skb_tailroom(skb) < hci_skb_expect(skb)) {
576 kfree_skb(skb);
577 skb = NULL;
578
579 err = -EILSEQ;
580 break;
581 }
582 }
583
584 if (!hci_skb_expect(skb)) {
585 /* Complete frame */
586 hci_recv_frame(data->hdev, skb);
587 skb = NULL;
588 }
589 }
590
591 data->sco_skb = skb;
592 spin_unlock(&data->rxlock);
593
594 return err;
595}
596
597static void btusb_intr_complete(struct urb *urb)
598{
599 struct hci_dev *hdev = urb->context;
600 struct btusb_data *data = hci_get_drvdata(hdev);
601 int err;
602
603 BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
604 urb->actual_length);
605
606 if (!test_bit(HCI_RUNNING, &hdev->flags))
607 return;
608
609 if (urb->status == 0) {
610 hdev->stat.byte_rx += urb->actual_length;
611
612 if (btusb_recv_intr(data, urb->transfer_buffer,
613 urb->actual_length) < 0) {
614 BT_ERR("%s corrupted event packet", hdev->name);
615 hdev->stat.err_rx++;
616 }
617 } else if (urb->status == -ENOENT) {
618 /* Avoid suspend failed when usb_kill_urb */
619 return;
620 }
621
622 if (!test_bit(BTUSB_INTR_RUNNING, &data->flags))
623 return;
624
625 usb_mark_last_busy(data->udev);
626 usb_anchor_urb(urb, &data->intr_anchor);
627
628 err = usb_submit_urb(urb, GFP_ATOMIC);
629 if (err < 0) {
630 /* -EPERM: urb is being killed;
631 * -ENODEV: device got disconnected */
632 if (err != -EPERM && err != -ENODEV)
633 BT_ERR("%s urb %p failed to resubmit (%d)",
634 hdev->name, urb, -err);
635 usb_unanchor_urb(urb);
636 }
637}
638
639static int btusb_submit_intr_urb(struct hci_dev *hdev, gfp_t mem_flags)
640{
641 struct btusb_data *data = hci_get_drvdata(hdev);
642 struct urb *urb;
643 unsigned char *buf;
644 unsigned int pipe;
645 int err, size;
646
647 BT_DBG("%s", hdev->name);
648
649 if (!data->intr_ep)
650 return -ENODEV;
651
652 urb = usb_alloc_urb(0, mem_flags);
653 if (!urb)
654 return -ENOMEM;
655
656 size = le16_to_cpu(data->intr_ep->wMaxPacketSize);
657
658 buf = kmalloc(size, mem_flags);
659 if (!buf) {
660 usb_free_urb(urb);
661 return -ENOMEM;
662 }
663
664 pipe = usb_rcvintpipe(data->udev, data->intr_ep->bEndpointAddress);
665
666 usb_fill_int_urb(urb, data->udev, pipe, buf, size,
667 btusb_intr_complete, hdev, data->intr_ep->bInterval);
668
669 urb->transfer_flags |= URB_FREE_BUFFER;
670
671 usb_anchor_urb(urb, &data->intr_anchor);
672
673 err = usb_submit_urb(urb, mem_flags);
674 if (err < 0) {
675 if (err != -EPERM && err != -ENODEV)
676 BT_ERR("%s urb %p submission failed (%d)",
677 hdev->name, urb, -err);
678 usb_unanchor_urb(urb);
679 }
680
681 usb_free_urb(urb);
682
683 return err;
684}
685
686static void btusb_bulk_complete(struct urb *urb)
687{
688 struct hci_dev *hdev = urb->context;
689 struct btusb_data *data = hci_get_drvdata(hdev);
690 int err;
691
692 BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
693 urb->actual_length);
694
695 if (!test_bit(HCI_RUNNING, &hdev->flags))
696 return;
697
698 if (urb->status == 0) {
699 hdev->stat.byte_rx += urb->actual_length;
700
701 if (data->recv_bulk(data, urb->transfer_buffer,
702 urb->actual_length) < 0) {
703 BT_ERR("%s corrupted ACL packet", hdev->name);
704 hdev->stat.err_rx++;
705 }
706 } else if (urb->status == -ENOENT) {
707 /* Avoid suspend failed when usb_kill_urb */
708 return;
709 }
710
711 if (!test_bit(BTUSB_BULK_RUNNING, &data->flags))
712 return;
713
714 usb_anchor_urb(urb, &data->bulk_anchor);
715 usb_mark_last_busy(data->udev);
716
717 err = usb_submit_urb(urb, GFP_ATOMIC);
718 if (err < 0) {
719 /* -EPERM: urb is being killed;
720 * -ENODEV: device got disconnected */
721 if (err != -EPERM && err != -ENODEV)
722 BT_ERR("%s urb %p failed to resubmit (%d)",
723 hdev->name, urb, -err);
724 usb_unanchor_urb(urb);
725 }
726}
727
728static int btusb_submit_bulk_urb(struct hci_dev *hdev, gfp_t mem_flags)
729{
730 struct btusb_data *data = hci_get_drvdata(hdev);
731 struct urb *urb;
732 unsigned char *buf;
733 unsigned int pipe;
734 int err, size = HCI_MAX_FRAME_SIZE;
735
736 BT_DBG("%s", hdev->name);
737
738 if (!data->bulk_rx_ep)
739 return -ENODEV;
740
741 urb = usb_alloc_urb(0, mem_flags);
742 if (!urb)
743 return -ENOMEM;
744
745 buf = kmalloc(size, mem_flags);
746 if (!buf) {
747 usb_free_urb(urb);
748 return -ENOMEM;
749 }
750
751 pipe = usb_rcvbulkpipe(data->udev, data->bulk_rx_ep->bEndpointAddress);
752
753 usb_fill_bulk_urb(urb, data->udev, pipe, buf, size,
754 btusb_bulk_complete, hdev);
755
756 urb->transfer_flags |= URB_FREE_BUFFER;
757
758 usb_mark_last_busy(data->udev);
759 usb_anchor_urb(urb, &data->bulk_anchor);
760
761 err = usb_submit_urb(urb, mem_flags);
762 if (err < 0) {
763 if (err != -EPERM && err != -ENODEV)
764 BT_ERR("%s urb %p submission failed (%d)",
765 hdev->name, urb, -err);
766 usb_unanchor_urb(urb);
767 }
768
769 usb_free_urb(urb);
770
771 return err;
772}
773
774static void btusb_isoc_complete(struct urb *urb)
775{
776 struct hci_dev *hdev = urb->context;
777 struct btusb_data *data = hci_get_drvdata(hdev);
778 int i, err;
779
780 BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
781 urb->actual_length);
782
783 if (!test_bit(HCI_RUNNING, &hdev->flags))
784 return;
785
786 if (urb->status == 0) {
787 for (i = 0; i < urb->number_of_packets; i++) {
788 unsigned int offset = urb->iso_frame_desc[i].offset;
789 unsigned int length = urb->iso_frame_desc[i].actual_length;
790
791 if (urb->iso_frame_desc[i].status)
792 continue;
793
794 hdev->stat.byte_rx += length;
795
796 if (btusb_recv_isoc(data, urb->transfer_buffer + offset,
797 length) < 0) {
798 BT_ERR("%s corrupted SCO packet", hdev->name);
799 hdev->stat.err_rx++;
800 }
801 }
802 } else if (urb->status == -ENOENT) {
803 /* Avoid suspend failed when usb_kill_urb */
804 return;
805 }
806
807 if (!test_bit(BTUSB_ISOC_RUNNING, &data->flags))
808 return;
809
810 usb_anchor_urb(urb, &data->isoc_anchor);
811
812 err = usb_submit_urb(urb, GFP_ATOMIC);
813 if (err < 0) {
814 /* -EPERM: urb is being killed;
815 * -ENODEV: device got disconnected */
816 if (err != -EPERM && err != -ENODEV)
817 BT_ERR("%s urb %p failed to resubmit (%d)",
818 hdev->name, urb, -err);
819 usb_unanchor_urb(urb);
820 }
821}
822
823static inline void __fill_isoc_descriptor(struct urb *urb, int len, int mtu)
824{
825 int i, offset = 0;
826
827 BT_DBG("len %d mtu %d", len, mtu);
828
829 for (i = 0; i < BTUSB_MAX_ISOC_FRAMES && len >= mtu;
830 i++, offset += mtu, len -= mtu) {
831 urb->iso_frame_desc[i].offset = offset;
832 urb->iso_frame_desc[i].length = mtu;
833 }
834
835 if (len && i < BTUSB_MAX_ISOC_FRAMES) {
836 urb->iso_frame_desc[i].offset = offset;
837 urb->iso_frame_desc[i].length = len;
838 i++;
839 }
840
841 urb->number_of_packets = i;
842}
843
844static int btusb_submit_isoc_urb(struct hci_dev *hdev, gfp_t mem_flags)
845{
846 struct btusb_data *data = hci_get_drvdata(hdev);
847 struct urb *urb;
848 unsigned char *buf;
849 unsigned int pipe;
850 int err, size;
851
852 BT_DBG("%s", hdev->name);
853
854 if (!data->isoc_rx_ep)
855 return -ENODEV;
856
857 urb = usb_alloc_urb(BTUSB_MAX_ISOC_FRAMES, mem_flags);
858 if (!urb)
859 return -ENOMEM;
860
861 size = le16_to_cpu(data->isoc_rx_ep->wMaxPacketSize) *
862 BTUSB_MAX_ISOC_FRAMES;
863
864 buf = kmalloc(size, mem_flags);
865 if (!buf) {
866 usb_free_urb(urb);
867 return -ENOMEM;
868 }
869
870 pipe = usb_rcvisocpipe(data->udev, data->isoc_rx_ep->bEndpointAddress);
871
872 usb_fill_int_urb(urb, data->udev, pipe, buf, size, btusb_isoc_complete,
873 hdev, data->isoc_rx_ep->bInterval);
874
875 urb->transfer_flags = URB_FREE_BUFFER | URB_ISO_ASAP;
876
877 __fill_isoc_descriptor(urb, size,
878 le16_to_cpu(data->isoc_rx_ep->wMaxPacketSize));
879
880 usb_anchor_urb(urb, &data->isoc_anchor);
881
882 err = usb_submit_urb(urb, mem_flags);
883 if (err < 0) {
884 if (err != -EPERM && err != -ENODEV)
885 BT_ERR("%s urb %p submission failed (%d)",
886 hdev->name, urb, -err);
887 usb_unanchor_urb(urb);
888 }
889
890 usb_free_urb(urb);
891
892 return err;
893}
894
895static void btusb_diag_complete(struct urb *urb)
896{
897 struct hci_dev *hdev = urb->context;
898 struct btusb_data *data = hci_get_drvdata(hdev);
899 int err;
900
901 BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
902 urb->actual_length);
903
904 if (urb->status == 0) {
905 struct sk_buff *skb;
906
907 skb = bt_skb_alloc(urb->actual_length, GFP_ATOMIC);
908 if (skb) {
909 memcpy(skb_put(skb, urb->actual_length),
910 urb->transfer_buffer, urb->actual_length);
911 hci_recv_diag(hdev, skb);
912 }
913 } else if (urb->status == -ENOENT) {
914 /* Avoid suspend failed when usb_kill_urb */
915 return;
916 }
917
918 if (!test_bit(BTUSB_DIAG_RUNNING, &data->flags))
919 return;
920
921 usb_anchor_urb(urb, &data->diag_anchor);
922 usb_mark_last_busy(data->udev);
923
924 err = usb_submit_urb(urb, GFP_ATOMIC);
925 if (err < 0) {
926 /* -EPERM: urb is being killed;
927 * -ENODEV: device got disconnected */
928 if (err != -EPERM && err != -ENODEV)
929 BT_ERR("%s urb %p failed to resubmit (%d)",
930 hdev->name, urb, -err);
931 usb_unanchor_urb(urb);
932 }
933}
934
935static int btusb_submit_diag_urb(struct hci_dev *hdev, gfp_t mem_flags)
936{
937 struct btusb_data *data = hci_get_drvdata(hdev);
938 struct urb *urb;
939 unsigned char *buf;
940 unsigned int pipe;
941 int err, size = HCI_MAX_FRAME_SIZE;
942
943 BT_DBG("%s", hdev->name);
944
945 if (!data->diag_rx_ep)
946 return -ENODEV;
947
948 urb = usb_alloc_urb(0, mem_flags);
949 if (!urb)
950 return -ENOMEM;
951
952 buf = kmalloc(size, mem_flags);
953 if (!buf) {
954 usb_free_urb(urb);
955 return -ENOMEM;
956 }
957
958 pipe = usb_rcvbulkpipe(data->udev, data->diag_rx_ep->bEndpointAddress);
959
960 usb_fill_bulk_urb(urb, data->udev, pipe, buf, size,
961 btusb_diag_complete, hdev);
962
963 urb->transfer_flags |= URB_FREE_BUFFER;
964
965 usb_mark_last_busy(data->udev);
966 usb_anchor_urb(urb, &data->diag_anchor);
967
968 err = usb_submit_urb(urb, mem_flags);
969 if (err < 0) {
970 if (err != -EPERM && err != -ENODEV)
971 BT_ERR("%s urb %p submission failed (%d)",
972 hdev->name, urb, -err);
973 usb_unanchor_urb(urb);
974 }
975
976 usb_free_urb(urb);
977
978 return err;
979}
980
981static void btusb_tx_complete(struct urb *urb)
982{
983 struct sk_buff *skb = urb->context;
984 struct hci_dev *hdev = (struct hci_dev *)skb->dev;
985 struct btusb_data *data = hci_get_drvdata(hdev);
986
987 BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
988 urb->actual_length);
989
990 if (!test_bit(HCI_RUNNING, &hdev->flags))
991 goto done;
992
993 if (!urb->status)
994 hdev->stat.byte_tx += urb->transfer_buffer_length;
995 else
996 hdev->stat.err_tx++;
997
998done:
999 spin_lock(&data->txlock);
1000 data->tx_in_flight--;
1001 spin_unlock(&data->txlock);
1002
1003 kfree(urb->setup_packet);
1004
1005 kfree_skb(skb);
1006}
1007
1008static void btusb_isoc_tx_complete(struct urb *urb)
1009{
1010 struct sk_buff *skb = urb->context;
1011 struct hci_dev *hdev = (struct hci_dev *)skb->dev;
1012
1013 BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
1014 urb->actual_length);
1015
1016 if (!test_bit(HCI_RUNNING, &hdev->flags))
1017 goto done;
1018
1019 if (!urb->status)
1020 hdev->stat.byte_tx += urb->transfer_buffer_length;
1021 else
1022 hdev->stat.err_tx++;
1023
1024done:
1025 kfree(urb->setup_packet);
1026
1027 kfree_skb(skb);
1028}
1029
1030static int btusb_open(struct hci_dev *hdev)
1031{
1032 struct btusb_data *data = hci_get_drvdata(hdev);
1033 int err;
1034
1035 BT_DBG("%s", hdev->name);
1036
1037 /* Patching USB firmware files prior to starting any URBs of HCI path
1038 * It is more safe to use USB bulk channel for downloading USB patch
1039 */
1040 if (data->setup_on_usb) {
1041 err = data->setup_on_usb(hdev);
1042 if (err < 0)
1043 return err;
1044 }
1045
1046 err = usb_autopm_get_interface(data->intf);
1047 if (err < 0)
1048 return err;
1049
1050 data->intf->needs_remote_wakeup = 1;
1051
1052 if (test_and_set_bit(BTUSB_INTR_RUNNING, &data->flags))
1053 goto done;
1054
1055 err = btusb_submit_intr_urb(hdev, GFP_KERNEL);
1056 if (err < 0)
1057 goto failed;
1058
1059 err = btusb_submit_bulk_urb(hdev, GFP_KERNEL);
1060 if (err < 0) {
1061 usb_kill_anchored_urbs(&data->intr_anchor);
1062 goto failed;
1063 }
1064
1065 set_bit(BTUSB_BULK_RUNNING, &data->flags);
1066 btusb_submit_bulk_urb(hdev, GFP_KERNEL);
1067
1068 if (data->diag) {
1069 if (!btusb_submit_diag_urb(hdev, GFP_KERNEL))
1070 set_bit(BTUSB_DIAG_RUNNING, &data->flags);
1071 }
1072
1073done:
1074 usb_autopm_put_interface(data->intf);
1075 return 0;
1076
1077failed:
1078 clear_bit(BTUSB_INTR_RUNNING, &data->flags);
1079 usb_autopm_put_interface(data->intf);
1080 return err;
1081}
1082
1083static void btusb_stop_traffic(struct btusb_data *data)
1084{
1085 usb_kill_anchored_urbs(&data->intr_anchor);
1086 usb_kill_anchored_urbs(&data->bulk_anchor);
1087 usb_kill_anchored_urbs(&data->isoc_anchor);
1088 usb_kill_anchored_urbs(&data->diag_anchor);
1089}
1090
1091static int btusb_close(struct hci_dev *hdev)
1092{
1093 struct btusb_data *data = hci_get_drvdata(hdev);
1094 int err;
1095
1096 BT_DBG("%s", hdev->name);
1097
1098 cancel_work_sync(&data->work);
1099 cancel_work_sync(&data->waker);
1100
1101 clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
1102 clear_bit(BTUSB_BULK_RUNNING, &data->flags);
1103 clear_bit(BTUSB_INTR_RUNNING, &data->flags);
1104 clear_bit(BTUSB_DIAG_RUNNING, &data->flags);
1105
1106 btusb_stop_traffic(data);
1107 btusb_free_frags(data);
1108
1109 err = usb_autopm_get_interface(data->intf);
1110 if (err < 0)
1111 goto failed;
1112
1113 data->intf->needs_remote_wakeup = 0;
1114 usb_autopm_put_interface(data->intf);
1115
1116failed:
1117 usb_scuttle_anchored_urbs(&data->deferred);
1118 return 0;
1119}
1120
1121static int btusb_flush(struct hci_dev *hdev)
1122{
1123 struct btusb_data *data = hci_get_drvdata(hdev);
1124
1125 BT_DBG("%s", hdev->name);
1126
1127 usb_kill_anchored_urbs(&data->tx_anchor);
1128 btusb_free_frags(data);
1129
1130 return 0;
1131}
1132
1133static struct urb *alloc_ctrl_urb(struct hci_dev *hdev, struct sk_buff *skb)
1134{
1135 struct btusb_data *data = hci_get_drvdata(hdev);
1136 struct usb_ctrlrequest *dr;
1137 struct urb *urb;
1138 unsigned int pipe;
1139
1140 urb = usb_alloc_urb(0, GFP_KERNEL);
1141 if (!urb)
1142 return ERR_PTR(-ENOMEM);
1143
1144 dr = kmalloc(sizeof(*dr), GFP_KERNEL);
1145 if (!dr) {
1146 usb_free_urb(urb);
1147 return ERR_PTR(-ENOMEM);
1148 }
1149
1150 dr->bRequestType = data->cmdreq_type;
1151 dr->bRequest = data->cmdreq;
1152 dr->wIndex = 0;
1153 dr->wValue = 0;
1154 dr->wLength = __cpu_to_le16(skb->len);
1155
1156 pipe = usb_sndctrlpipe(data->udev, 0x00);
1157
1158 usb_fill_control_urb(urb, data->udev, pipe, (void *)dr,
1159 skb->data, skb->len, btusb_tx_complete, skb);
1160
1161 skb->dev = (void *)hdev;
1162
1163 return urb;
1164}
1165
1166static struct urb *alloc_bulk_urb(struct hci_dev *hdev, struct sk_buff *skb)
1167{
1168 struct btusb_data *data = hci_get_drvdata(hdev);
1169 struct urb *urb;
1170 unsigned int pipe;
1171
1172 if (!data->bulk_tx_ep)
1173 return ERR_PTR(-ENODEV);
1174
1175 urb = usb_alloc_urb(0, GFP_KERNEL);
1176 if (!urb)
1177 return ERR_PTR(-ENOMEM);
1178
1179 pipe = usb_sndbulkpipe(data->udev, data->bulk_tx_ep->bEndpointAddress);
1180
1181 usb_fill_bulk_urb(urb, data->udev, pipe,
1182 skb->data, skb->len, btusb_tx_complete, skb);
1183
1184 skb->dev = (void *)hdev;
1185
1186 return urb;
1187}
1188
1189static struct urb *alloc_isoc_urb(struct hci_dev *hdev, struct sk_buff *skb)
1190{
1191 struct btusb_data *data = hci_get_drvdata(hdev);
1192 struct urb *urb;
1193 unsigned int pipe;
1194
1195 if (!data->isoc_tx_ep)
1196 return ERR_PTR(-ENODEV);
1197
1198 urb = usb_alloc_urb(BTUSB_MAX_ISOC_FRAMES, GFP_KERNEL);
1199 if (!urb)
1200 return ERR_PTR(-ENOMEM);
1201
1202 pipe = usb_sndisocpipe(data->udev, data->isoc_tx_ep->bEndpointAddress);
1203
1204 usb_fill_int_urb(urb, data->udev, pipe,
1205 skb->data, skb->len, btusb_isoc_tx_complete,
1206 skb, data->isoc_tx_ep->bInterval);
1207
1208 urb->transfer_flags = URB_ISO_ASAP;
1209
1210 __fill_isoc_descriptor(urb, skb->len,
1211 le16_to_cpu(data->isoc_tx_ep->wMaxPacketSize));
1212
1213 skb->dev = (void *)hdev;
1214
1215 return urb;
1216}
1217
1218static int submit_tx_urb(struct hci_dev *hdev, struct urb *urb)
1219{
1220 struct btusb_data *data = hci_get_drvdata(hdev);
1221 int err;
1222
1223 usb_anchor_urb(urb, &data->tx_anchor);
1224
1225 err = usb_submit_urb(urb, GFP_KERNEL);
1226 if (err < 0) {
1227 if (err != -EPERM && err != -ENODEV)
1228 BT_ERR("%s urb %p submission failed (%d)",
1229 hdev->name, urb, -err);
1230 kfree(urb->setup_packet);
1231 usb_unanchor_urb(urb);
1232 } else {
1233 usb_mark_last_busy(data->udev);
1234 }
1235
1236 usb_free_urb(urb);
1237 return err;
1238}
1239
1240static int submit_or_queue_tx_urb(struct hci_dev *hdev, struct urb *urb)
1241{
1242 struct btusb_data *data = hci_get_drvdata(hdev);
1243 unsigned long flags;
1244 bool suspending;
1245
1246 spin_lock_irqsave(&data->txlock, flags);
1247 suspending = test_bit(BTUSB_SUSPENDING, &data->flags);
1248 if (!suspending)
1249 data->tx_in_flight++;
1250 spin_unlock_irqrestore(&data->txlock, flags);
1251
1252 if (!suspending)
1253 return submit_tx_urb(hdev, urb);
1254
1255 usb_anchor_urb(urb, &data->deferred);
1256 schedule_work(&data->waker);
1257
1258 usb_free_urb(urb);
1259 return 0;
1260}
1261
1262static int btusb_send_frame(struct hci_dev *hdev, struct sk_buff *skb)
1263{
1264 struct urb *urb;
1265
1266 BT_DBG("%s", hdev->name);
1267
1268 switch (hci_skb_pkt_type(skb)) {
1269 case HCI_COMMAND_PKT:
1270 urb = alloc_ctrl_urb(hdev, skb);
1271 if (IS_ERR(urb))
1272 return PTR_ERR(urb);
1273
1274 hdev->stat.cmd_tx++;
1275 return submit_or_queue_tx_urb(hdev, urb);
1276
1277 case HCI_ACLDATA_PKT:
1278 urb = alloc_bulk_urb(hdev, skb);
1279 if (IS_ERR(urb))
1280 return PTR_ERR(urb);
1281
1282 hdev->stat.acl_tx++;
1283 return submit_or_queue_tx_urb(hdev, urb);
1284
1285 case HCI_SCODATA_PKT:
1286 if (hci_conn_num(hdev, SCO_LINK) < 1)
1287 return -ENODEV;
1288
1289 urb = alloc_isoc_urb(hdev, skb);
1290 if (IS_ERR(urb))
1291 return PTR_ERR(urb);
1292
1293 hdev->stat.sco_tx++;
1294 return submit_tx_urb(hdev, urb);
1295 }
1296
1297 return -EILSEQ;
1298}
1299
1300static void btusb_notify(struct hci_dev *hdev, unsigned int evt)
1301{
1302 struct btusb_data *data = hci_get_drvdata(hdev);
1303
1304 BT_DBG("%s evt %d", hdev->name, evt);
1305
1306 if (hci_conn_num(hdev, SCO_LINK) != data->sco_num) {
1307 data->sco_num = hci_conn_num(hdev, SCO_LINK);
1308 schedule_work(&data->work);
1309 }
1310}
1311
1312static inline int __set_isoc_interface(struct hci_dev *hdev, int altsetting)
1313{
1314 struct btusb_data *data = hci_get_drvdata(hdev);
1315 struct usb_interface *intf = data->isoc;
1316 struct usb_endpoint_descriptor *ep_desc;
1317 int i, err;
1318
1319 if (!data->isoc)
1320 return -ENODEV;
1321
1322 err = usb_set_interface(data->udev, 1, altsetting);
1323 if (err < 0) {
1324 BT_ERR("%s setting interface failed (%d)", hdev->name, -err);
1325 return err;
1326 }
1327
1328 data->isoc_altsetting = altsetting;
1329
1330 data->isoc_tx_ep = NULL;
1331 data->isoc_rx_ep = NULL;
1332
1333 for (i = 0; i < intf->cur_altsetting->desc.bNumEndpoints; i++) {
1334 ep_desc = &intf->cur_altsetting->endpoint[i].desc;
1335
1336 if (!data->isoc_tx_ep && usb_endpoint_is_isoc_out(ep_desc)) {
1337 data->isoc_tx_ep = ep_desc;
1338 continue;
1339 }
1340
1341 if (!data->isoc_rx_ep && usb_endpoint_is_isoc_in(ep_desc)) {
1342 data->isoc_rx_ep = ep_desc;
1343 continue;
1344 }
1345 }
1346
1347 if (!data->isoc_tx_ep || !data->isoc_rx_ep) {
1348 BT_ERR("%s invalid SCO descriptors", hdev->name);
1349 return -ENODEV;
1350 }
1351
1352 return 0;
1353}
1354
1355static void btusb_work(struct work_struct *work)
1356{
1357 struct btusb_data *data = container_of(work, struct btusb_data, work);
1358 struct hci_dev *hdev = data->hdev;
1359 int new_alts;
1360 int err;
1361
1362 if (data->sco_num > 0) {
1363 if (!test_bit(BTUSB_DID_ISO_RESUME, &data->flags)) {
1364 err = usb_autopm_get_interface(data->isoc ? data->isoc : data->intf);
1365 if (err < 0) {
1366 clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
1367 usb_kill_anchored_urbs(&data->isoc_anchor);
1368 return;
1369 }
1370
1371 set_bit(BTUSB_DID_ISO_RESUME, &data->flags);
1372 }
1373
1374 if (hdev->voice_setting & 0x0020) {
1375 static const int alts[3] = { 2, 4, 5 };
1376
1377 new_alts = alts[data->sco_num - 1];
1378 } else {
1379 new_alts = data->sco_num;
1380 }
1381
1382 if (data->isoc_altsetting != new_alts) {
1383 unsigned long flags;
1384
1385 clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
1386 usb_kill_anchored_urbs(&data->isoc_anchor);
1387
1388 /* When isochronous alternate setting needs to be
1389 * changed, because SCO connection has been added
1390 * or removed, a packet fragment may be left in the
1391 * reassembling state. This could lead to wrongly
1392 * assembled fragments.
1393 *
1394 * Clear outstanding fragment when selecting a new
1395 * alternate setting.
1396 */
1397 spin_lock_irqsave(&data->rxlock, flags);
1398 kfree_skb(data->sco_skb);
1399 data->sco_skb = NULL;
1400 spin_unlock_irqrestore(&data->rxlock, flags);
1401
1402 if (__set_isoc_interface(hdev, new_alts) < 0)
1403 return;
1404 }
1405
1406 if (!test_and_set_bit(BTUSB_ISOC_RUNNING, &data->flags)) {
1407 if (btusb_submit_isoc_urb(hdev, GFP_KERNEL) < 0)
1408 clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
1409 else
1410 btusb_submit_isoc_urb(hdev, GFP_KERNEL);
1411 }
1412 } else {
1413 clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
1414 usb_kill_anchored_urbs(&data->isoc_anchor);
1415
1416 __set_isoc_interface(hdev, 0);
1417 if (test_and_clear_bit(BTUSB_DID_ISO_RESUME, &data->flags))
1418 usb_autopm_put_interface(data->isoc ? data->isoc : data->intf);
1419 }
1420}
1421
1422static void btusb_waker(struct work_struct *work)
1423{
1424 struct btusb_data *data = container_of(work, struct btusb_data, waker);
1425 int err;
1426
1427 err = usb_autopm_get_interface(data->intf);
1428 if (err < 0)
1429 return;
1430
1431 usb_autopm_put_interface(data->intf);
1432}
1433
1434static int btusb_setup_bcm92035(struct hci_dev *hdev)
1435{
1436 struct sk_buff *skb;
1437 u8 val = 0x00;
1438
1439 BT_DBG("%s", hdev->name);
1440
1441 skb = __hci_cmd_sync(hdev, 0xfc3b, 1, &val, HCI_INIT_TIMEOUT);
1442 if (IS_ERR(skb))
1443 BT_ERR("BCM92035 command failed (%ld)", -PTR_ERR(skb));
1444 else
1445 kfree_skb(skb);
1446
1447 return 0;
1448}
1449
1450static int btusb_setup_csr(struct hci_dev *hdev)
1451{
1452 struct hci_rp_read_local_version *rp;
1453 struct sk_buff *skb;
1454
1455 BT_DBG("%s", hdev->name);
1456
1457 skb = __hci_cmd_sync(hdev, HCI_OP_READ_LOCAL_VERSION, 0, NULL,
1458 HCI_INIT_TIMEOUT);
1459 if (IS_ERR(skb)) {
1460 int err = PTR_ERR(skb);
1461 BT_ERR("%s: CSR: Local version failed (%d)", hdev->name, err);
1462 return err;
1463 }
1464
1465 if (skb->len != sizeof(struct hci_rp_read_local_version)) {
1466 BT_ERR("%s: CSR: Local version length mismatch", hdev->name);
1467 kfree_skb(skb);
1468 return -EIO;
1469 }
1470
1471 rp = (struct hci_rp_read_local_version *)skb->data;
1472
1473 /* Detect controllers which aren't real CSR ones. */
1474 if (le16_to_cpu(rp->manufacturer) != 10 ||
1475 le16_to_cpu(rp->lmp_subver) == 0x0c5c) {
1476 /* Clear the reset quirk since this is not an actual
1477 * early Bluetooth 1.1 device from CSR.
1478 */
1479 clear_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
1480
1481 /* These fake CSR controllers have all a broken
1482 * stored link key handling and so just disable it.
1483 */
1484 set_bit(HCI_QUIRK_BROKEN_STORED_LINK_KEY, &hdev->quirks);
1485 }
1486
1487 kfree_skb(skb);
1488
1489 return 0;
1490}
1491
1492static const struct firmware *btusb_setup_intel_get_fw(struct hci_dev *hdev,
1493 struct intel_version *ver)
1494{
1495 const struct firmware *fw;
1496 char fwname[64];
1497 int ret;
1498
1499 snprintf(fwname, sizeof(fwname),
1500 "intel/ibt-hw-%x.%x.%x-fw-%x.%x.%x.%x.%x.bseq",
1501 ver->hw_platform, ver->hw_variant, ver->hw_revision,
1502 ver->fw_variant, ver->fw_revision, ver->fw_build_num,
1503 ver->fw_build_ww, ver->fw_build_yy);
1504
1505 ret = request_firmware(&fw, fwname, &hdev->dev);
1506 if (ret < 0) {
1507 if (ret == -EINVAL) {
1508 BT_ERR("%s Intel firmware file request failed (%d)",
1509 hdev->name, ret);
1510 return NULL;
1511 }
1512
1513 BT_ERR("%s failed to open Intel firmware file: %s(%d)",
1514 hdev->name, fwname, ret);
1515
1516 /* If the correct firmware patch file is not found, use the
1517 * default firmware patch file instead
1518 */
1519 snprintf(fwname, sizeof(fwname), "intel/ibt-hw-%x.%x.bseq",
1520 ver->hw_platform, ver->hw_variant);
1521 if (request_firmware(&fw, fwname, &hdev->dev) < 0) {
1522 BT_ERR("%s failed to open default Intel fw file: %s",
1523 hdev->name, fwname);
1524 return NULL;
1525 }
1526 }
1527
1528 BT_INFO("%s: Intel Bluetooth firmware file: %s", hdev->name, fwname);
1529
1530 return fw;
1531}
1532
1533static int btusb_setup_intel_patching(struct hci_dev *hdev,
1534 const struct firmware *fw,
1535 const u8 **fw_ptr, int *disable_patch)
1536{
1537 struct sk_buff *skb;
1538 struct hci_command_hdr *cmd;
1539 const u8 *cmd_param;
1540 struct hci_event_hdr *evt = NULL;
1541 const u8 *evt_param = NULL;
1542 int remain = fw->size - (*fw_ptr - fw->data);
1543
1544 /* The first byte indicates the types of the patch command or event.
1545 * 0x01 means HCI command and 0x02 is HCI event. If the first bytes
1546 * in the current firmware buffer doesn't start with 0x01 or
1547 * the size of remain buffer is smaller than HCI command header,
1548 * the firmware file is corrupted and it should stop the patching
1549 * process.
1550 */
1551 if (remain > HCI_COMMAND_HDR_SIZE && *fw_ptr[0] != 0x01) {
1552 BT_ERR("%s Intel fw corrupted: invalid cmd read", hdev->name);
1553 return -EINVAL;
1554 }
1555 (*fw_ptr)++;
1556 remain--;
1557
1558 cmd = (struct hci_command_hdr *)(*fw_ptr);
1559 *fw_ptr += sizeof(*cmd);
1560 remain -= sizeof(*cmd);
1561
1562 /* Ensure that the remain firmware data is long enough than the length
1563 * of command parameter. If not, the firmware file is corrupted.
1564 */
1565 if (remain < cmd->plen) {
1566 BT_ERR("%s Intel fw corrupted: invalid cmd len", hdev->name);
1567 return -EFAULT;
1568 }
1569
1570 /* If there is a command that loads a patch in the firmware
1571 * file, then enable the patch upon success, otherwise just
1572 * disable the manufacturer mode, for example patch activation
1573 * is not required when the default firmware patch file is used
1574 * because there are no patch data to load.
1575 */
1576 if (*disable_patch && le16_to_cpu(cmd->opcode) == 0xfc8e)
1577 *disable_patch = 0;
1578
1579 cmd_param = *fw_ptr;
1580 *fw_ptr += cmd->plen;
1581 remain -= cmd->plen;
1582
1583 /* This reads the expected events when the above command is sent to the
1584 * device. Some vendor commands expects more than one events, for
1585 * example command status event followed by vendor specific event.
1586 * For this case, it only keeps the last expected event. so the command
1587 * can be sent with __hci_cmd_sync_ev() which returns the sk_buff of
1588 * last expected event.
1589 */
1590 while (remain > HCI_EVENT_HDR_SIZE && *fw_ptr[0] == 0x02) {
1591 (*fw_ptr)++;
1592 remain--;
1593
1594 evt = (struct hci_event_hdr *)(*fw_ptr);
1595 *fw_ptr += sizeof(*evt);
1596 remain -= sizeof(*evt);
1597
1598 if (remain < evt->plen) {
1599 BT_ERR("%s Intel fw corrupted: invalid evt len",
1600 hdev->name);
1601 return -EFAULT;
1602 }
1603
1604 evt_param = *fw_ptr;
1605 *fw_ptr += evt->plen;
1606 remain -= evt->plen;
1607 }
1608
1609 /* Every HCI commands in the firmware file has its correspond event.
1610 * If event is not found or remain is smaller than zero, the firmware
1611 * file is corrupted.
1612 */
1613 if (!evt || !evt_param || remain < 0) {
1614 BT_ERR("%s Intel fw corrupted: invalid evt read", hdev->name);
1615 return -EFAULT;
1616 }
1617
1618 skb = __hci_cmd_sync_ev(hdev, le16_to_cpu(cmd->opcode), cmd->plen,
1619 cmd_param, evt->evt, HCI_INIT_TIMEOUT);
1620 if (IS_ERR(skb)) {
1621 BT_ERR("%s sending Intel patch command (0x%4.4x) failed (%ld)",
1622 hdev->name, cmd->opcode, PTR_ERR(skb));
1623 return PTR_ERR(skb);
1624 }
1625
1626 /* It ensures that the returned event matches the event data read from
1627 * the firmware file. At fist, it checks the length and then
1628 * the contents of the event.
1629 */
1630 if (skb->len != evt->plen) {
1631 BT_ERR("%s mismatch event length (opcode 0x%4.4x)", hdev->name,
1632 le16_to_cpu(cmd->opcode));
1633 kfree_skb(skb);
1634 return -EFAULT;
1635 }
1636
1637 if (memcmp(skb->data, evt_param, evt->plen)) {
1638 BT_ERR("%s mismatch event parameter (opcode 0x%4.4x)",
1639 hdev->name, le16_to_cpu(cmd->opcode));
1640 kfree_skb(skb);
1641 return -EFAULT;
1642 }
1643 kfree_skb(skb);
1644
1645 return 0;
1646}
1647
1648static int btusb_setup_intel(struct hci_dev *hdev)
1649{
1650 struct sk_buff *skb;
1651 const struct firmware *fw;
1652 const u8 *fw_ptr;
1653 int disable_patch, err;
1654 struct intel_version ver;
1655
1656 BT_DBG("%s", hdev->name);
1657
1658 /* The controller has a bug with the first HCI command sent to it
1659 * returning number of completed commands as zero. This would stall the
1660 * command processing in the Bluetooth core.
1661 *
1662 * As a workaround, send HCI Reset command first which will reset the
1663 * number of completed commands and allow normal command processing
1664 * from now on.
1665 */
1666 skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL, HCI_INIT_TIMEOUT);
1667 if (IS_ERR(skb)) {
1668 BT_ERR("%s sending initial HCI reset command failed (%ld)",
1669 hdev->name, PTR_ERR(skb));
1670 return PTR_ERR(skb);
1671 }
1672 kfree_skb(skb);
1673
1674 /* Read Intel specific controller version first to allow selection of
1675 * which firmware file to load.
1676 *
1677 * The returned information are hardware variant and revision plus
1678 * firmware variant, revision and build number.
1679 */
1680 err = btintel_read_version(hdev, &ver);
1681 if (err)
1682 return err;
1683
1684 BT_INFO("%s: read Intel version: %02x%02x%02x%02x%02x%02x%02x%02x%02x",
1685 hdev->name, ver.hw_platform, ver.hw_variant, ver.hw_revision,
1686 ver.fw_variant, ver.fw_revision, ver.fw_build_num,
1687 ver.fw_build_ww, ver.fw_build_yy, ver.fw_patch_num);
1688
1689 /* fw_patch_num indicates the version of patch the device currently
1690 * have. If there is no patch data in the device, it is always 0x00.
1691 * So, if it is other than 0x00, no need to patch the device again.
1692 */
1693 if (ver.fw_patch_num) {
1694 BT_INFO("%s: Intel device is already patched. patch num: %02x",
1695 hdev->name, ver.fw_patch_num);
1696 goto complete;
1697 }
1698
1699 /* Opens the firmware patch file based on the firmware version read
1700 * from the controller. If it fails to open the matching firmware
1701 * patch file, it tries to open the default firmware patch file.
1702 * If no patch file is found, allow the device to operate without
1703 * a patch.
1704 */
1705 fw = btusb_setup_intel_get_fw(hdev, &ver);
1706 if (!fw)
1707 goto complete;
1708 fw_ptr = fw->data;
1709
1710 /* Enable the manufacturer mode of the controller.
1711 * Only while this mode is enabled, the driver can download the
1712 * firmware patch data and configuration parameters.
1713 */
1714 err = btintel_enter_mfg(hdev);
1715 if (err) {
1716 release_firmware(fw);
1717 return err;
1718 }
1719
1720 disable_patch = 1;
1721
1722 /* The firmware data file consists of list of Intel specific HCI
1723 * commands and its expected events. The first byte indicates the
1724 * type of the message, either HCI command or HCI event.
1725 *
1726 * It reads the command and its expected event from the firmware file,
1727 * and send to the controller. Once __hci_cmd_sync_ev() returns,
1728 * the returned event is compared with the event read from the firmware
1729 * file and it will continue until all the messages are downloaded to
1730 * the controller.
1731 *
1732 * Once the firmware patching is completed successfully,
1733 * the manufacturer mode is disabled with reset and activating the
1734 * downloaded patch.
1735 *
1736 * If the firmware patching fails, the manufacturer mode is
1737 * disabled with reset and deactivating the patch.
1738 *
1739 * If the default patch file is used, no reset is done when disabling
1740 * the manufacturer.
1741 */
1742 while (fw->size > fw_ptr - fw->data) {
1743 int ret;
1744
1745 ret = btusb_setup_intel_patching(hdev, fw, &fw_ptr,
1746 &disable_patch);
1747 if (ret < 0)
1748 goto exit_mfg_deactivate;
1749 }
1750
1751 release_firmware(fw);
1752
1753 if (disable_patch)
1754 goto exit_mfg_disable;
1755
1756 /* Patching completed successfully and disable the manufacturer mode
1757 * with reset and activate the downloaded firmware patches.
1758 */
1759 err = btintel_exit_mfg(hdev, true, true);
1760 if (err)
1761 return err;
1762
1763 BT_INFO("%s: Intel Bluetooth firmware patch completed and activated",
1764 hdev->name);
1765
1766 goto complete;
1767
1768exit_mfg_disable:
1769 /* Disable the manufacturer mode without reset */
1770 err = btintel_exit_mfg(hdev, false, false);
1771 if (err)
1772 return err;
1773
1774 BT_INFO("%s: Intel Bluetooth firmware patch completed", hdev->name);
1775
1776 goto complete;
1777
1778exit_mfg_deactivate:
1779 release_firmware(fw);
1780
1781 /* Patching failed. Disable the manufacturer mode with reset and
1782 * deactivate the downloaded firmware patches.
1783 */
1784 err = btintel_exit_mfg(hdev, true, false);
1785 if (err)
1786 return err;
1787
1788 BT_INFO("%s: Intel Bluetooth firmware patch completed and deactivated",
1789 hdev->name);
1790
1791complete:
1792 /* Set the event mask for Intel specific vendor events. This enables
1793 * a few extra events that are useful during general operation.
1794 */
1795 btintel_set_event_mask_mfg(hdev, false);
1796
1797 btintel_check_bdaddr(hdev);
1798 return 0;
1799}
1800
1801static int inject_cmd_complete(struct hci_dev *hdev, __u16 opcode)
1802{
1803 struct sk_buff *skb;
1804 struct hci_event_hdr *hdr;
1805 struct hci_ev_cmd_complete *evt;
1806
1807 skb = bt_skb_alloc(sizeof(*hdr) + sizeof(*evt) + 1, GFP_ATOMIC);
1808 if (!skb)
1809 return -ENOMEM;
1810
1811 hdr = (struct hci_event_hdr *)skb_put(skb, sizeof(*hdr));
1812 hdr->evt = HCI_EV_CMD_COMPLETE;
1813 hdr->plen = sizeof(*evt) + 1;
1814
1815 evt = (struct hci_ev_cmd_complete *)skb_put(skb, sizeof(*evt));
1816 evt->ncmd = 0x01;
1817 evt->opcode = cpu_to_le16(opcode);
1818
1819 *skb_put(skb, 1) = 0x00;
1820
1821 hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
1822
1823 return hci_recv_frame(hdev, skb);
1824}
1825
1826static int btusb_recv_bulk_intel(struct btusb_data *data, void *buffer,
1827 int count)
1828{
1829 /* When the device is in bootloader mode, then it can send
1830 * events via the bulk endpoint. These events are treated the
1831 * same way as the ones received from the interrupt endpoint.
1832 */
1833 if (test_bit(BTUSB_BOOTLOADER, &data->flags))
1834 return btusb_recv_intr(data, buffer, count);
1835
1836 return btusb_recv_bulk(data, buffer, count);
1837}
1838
1839static void btusb_intel_bootup(struct btusb_data *data, const void *ptr,
1840 unsigned int len)
1841{
1842 const struct intel_bootup *evt = ptr;
1843
1844 if (len != sizeof(*evt))
1845 return;
1846
1847 if (test_and_clear_bit(BTUSB_BOOTING, &data->flags)) {
1848 smp_mb__after_atomic();
1849 wake_up_bit(&data->flags, BTUSB_BOOTING);
1850 }
1851}
1852
1853static void btusb_intel_secure_send_result(struct btusb_data *data,
1854 const void *ptr, unsigned int len)
1855{
1856 const struct intel_secure_send_result *evt = ptr;
1857
1858 if (len != sizeof(*evt))
1859 return;
1860
1861 if (evt->result)
1862 set_bit(BTUSB_FIRMWARE_FAILED, &data->flags);
1863
1864 if (test_and_clear_bit(BTUSB_DOWNLOADING, &data->flags) &&
1865 test_bit(BTUSB_FIRMWARE_LOADED, &data->flags)) {
1866 smp_mb__after_atomic();
1867 wake_up_bit(&data->flags, BTUSB_DOWNLOADING);
1868 }
1869}
1870
1871static int btusb_recv_event_intel(struct hci_dev *hdev, struct sk_buff *skb)
1872{
1873 struct btusb_data *data = hci_get_drvdata(hdev);
1874
1875 if (test_bit(BTUSB_BOOTLOADER, &data->flags)) {
1876 struct hci_event_hdr *hdr = (void *)skb->data;
1877
1878 if (skb->len > HCI_EVENT_HDR_SIZE && hdr->evt == 0xff &&
1879 hdr->plen > 0) {
1880 const void *ptr = skb->data + HCI_EVENT_HDR_SIZE + 1;
1881 unsigned int len = skb->len - HCI_EVENT_HDR_SIZE - 1;
1882
1883 switch (skb->data[2]) {
1884 case 0x02:
1885 /* When switching to the operational firmware
1886 * the device sends a vendor specific event
1887 * indicating that the bootup completed.
1888 */
1889 btusb_intel_bootup(data, ptr, len);
1890 break;
1891 case 0x06:
1892 /* When the firmware loading completes the
1893 * device sends out a vendor specific event
1894 * indicating the result of the firmware
1895 * loading.
1896 */
1897 btusb_intel_secure_send_result(data, ptr, len);
1898 break;
1899 }
1900 }
1901 }
1902
1903 return hci_recv_frame(hdev, skb);
1904}
1905
1906static int btusb_send_frame_intel(struct hci_dev *hdev, struct sk_buff *skb)
1907{
1908 struct btusb_data *data = hci_get_drvdata(hdev);
1909 struct urb *urb;
1910
1911 BT_DBG("%s", hdev->name);
1912
1913 switch (hci_skb_pkt_type(skb)) {
1914 case HCI_COMMAND_PKT:
1915 if (test_bit(BTUSB_BOOTLOADER, &data->flags)) {
1916 struct hci_command_hdr *cmd = (void *)skb->data;
1917 __u16 opcode = le16_to_cpu(cmd->opcode);
1918
1919 /* When in bootloader mode and the command 0xfc09
1920 * is received, it needs to be send down the
1921 * bulk endpoint. So allocate a bulk URB instead.
1922 */
1923 if (opcode == 0xfc09)
1924 urb = alloc_bulk_urb(hdev, skb);
1925 else
1926 urb = alloc_ctrl_urb(hdev, skb);
1927
1928 /* When the 0xfc01 command is issued to boot into
1929 * the operational firmware, it will actually not
1930 * send a command complete event. To keep the flow
1931 * control working inject that event here.
1932 */
1933 if (opcode == 0xfc01)
1934 inject_cmd_complete(hdev, opcode);
1935 } else {
1936 urb = alloc_ctrl_urb(hdev, skb);
1937 }
1938 if (IS_ERR(urb))
1939 return PTR_ERR(urb);
1940
1941 hdev->stat.cmd_tx++;
1942 return submit_or_queue_tx_urb(hdev, urb);
1943
1944 case HCI_ACLDATA_PKT:
1945 urb = alloc_bulk_urb(hdev, skb);
1946 if (IS_ERR(urb))
1947 return PTR_ERR(urb);
1948
1949 hdev->stat.acl_tx++;
1950 return submit_or_queue_tx_urb(hdev, urb);
1951
1952 case HCI_SCODATA_PKT:
1953 if (hci_conn_num(hdev, SCO_LINK) < 1)
1954 return -ENODEV;
1955
1956 urb = alloc_isoc_urb(hdev, skb);
1957 if (IS_ERR(urb))
1958 return PTR_ERR(urb);
1959
1960 hdev->stat.sco_tx++;
1961 return submit_tx_urb(hdev, urb);
1962 }
1963
1964 return -EILSEQ;
1965}
1966
1967static int btusb_setup_intel_new(struct hci_dev *hdev)
1968{
1969 static const u8 reset_param[] = { 0x00, 0x01, 0x00, 0x01,
1970 0x00, 0x08, 0x04, 0x00 };
1971 struct btusb_data *data = hci_get_drvdata(hdev);
1972 struct sk_buff *skb;
1973 struct intel_version ver;
1974 struct intel_boot_params *params;
1975 const struct firmware *fw;
1976 const u8 *fw_ptr;
1977 u32 frag_len;
1978 char fwname[64];
1979 ktime_t calltime, delta, rettime;
1980 unsigned long long duration;
1981 int err;
1982
1983 BT_DBG("%s", hdev->name);
1984
1985 calltime = ktime_get();
1986
1987 /* Read the Intel version information to determine if the device
1988 * is in bootloader mode or if it already has operational firmware
1989 * loaded.
1990 */
1991 err = btintel_read_version(hdev, &ver);
1992 if (err)
1993 return err;
1994
1995 /* The hardware platform number has a fixed value of 0x37 and
1996 * for now only accept this single value.
1997 */
1998 if (ver.hw_platform != 0x37) {
1999 BT_ERR("%s: Unsupported Intel hardware platform (%u)",
2000 hdev->name, ver.hw_platform);
2001 return -EINVAL;
2002 }
2003
2004 /* At the moment only the hardware variant iBT 3.0 (LnP/SfP) is
2005 * supported by this firmware loading method. This check has been
2006 * put in place to ensure correct forward compatibility options
2007 * when newer hardware variants come along.
2008 */
2009 if (ver.hw_variant != 0x0b) {
2010 BT_ERR("%s: Unsupported Intel hardware variant (%u)",
2011 hdev->name, ver.hw_variant);
2012 return -EINVAL;
2013 }
2014
2015 btintel_version_info(hdev, &ver);
2016
2017 /* The firmware variant determines if the device is in bootloader
2018 * mode or is running operational firmware. The value 0x06 identifies
2019 * the bootloader and the value 0x23 identifies the operational
2020 * firmware.
2021 *
2022 * When the operational firmware is already present, then only
2023 * the check for valid Bluetooth device address is needed. This
2024 * determines if the device will be added as configured or
2025 * unconfigured controller.
2026 *
2027 * It is not possible to use the Secure Boot Parameters in this
2028 * case since that command is only available in bootloader mode.
2029 */
2030 if (ver.fw_variant == 0x23) {
2031 clear_bit(BTUSB_BOOTLOADER, &data->flags);
2032 btintel_check_bdaddr(hdev);
2033 return 0;
2034 }
2035
2036 /* If the device is not in bootloader mode, then the only possible
2037 * choice is to return an error and abort the device initialization.
2038 */
2039 if (ver.fw_variant != 0x06) {
2040 BT_ERR("%s: Unsupported Intel firmware variant (%u)",
2041 hdev->name, ver.fw_variant);
2042 return -ENODEV;
2043 }
2044
2045 /* Read the secure boot parameters to identify the operating
2046 * details of the bootloader.
2047 */
2048 skb = __hci_cmd_sync(hdev, 0xfc0d, 0, NULL, HCI_INIT_TIMEOUT);
2049 if (IS_ERR(skb)) {
2050 BT_ERR("%s: Reading Intel boot parameters failed (%ld)",
2051 hdev->name, PTR_ERR(skb));
2052 return PTR_ERR(skb);
2053 }
2054
2055 if (skb->len != sizeof(*params)) {
2056 BT_ERR("%s: Intel boot parameters size mismatch", hdev->name);
2057 kfree_skb(skb);
2058 return -EILSEQ;
2059 }
2060
2061 params = (struct intel_boot_params *)skb->data;
2062
2063 BT_INFO("%s: Device revision is %u", hdev->name,
2064 le16_to_cpu(params->dev_revid));
2065
2066 BT_INFO("%s: Secure boot is %s", hdev->name,
2067 params->secure_boot ? "enabled" : "disabled");
2068
2069 BT_INFO("%s: OTP lock is %s", hdev->name,
2070 params->otp_lock ? "enabled" : "disabled");
2071
2072 BT_INFO("%s: API lock is %s", hdev->name,
2073 params->api_lock ? "enabled" : "disabled");
2074
2075 BT_INFO("%s: Debug lock is %s", hdev->name,
2076 params->debug_lock ? "enabled" : "disabled");
2077
2078 BT_INFO("%s: Minimum firmware build %u week %u %u", hdev->name,
2079 params->min_fw_build_nn, params->min_fw_build_cw,
2080 2000 + params->min_fw_build_yy);
2081
2082 /* It is required that every single firmware fragment is acknowledged
2083 * with a command complete event. If the boot parameters indicate
2084 * that this bootloader does not send them, then abort the setup.
2085 */
2086 if (params->limited_cce != 0x00) {
2087 BT_ERR("%s: Unsupported Intel firmware loading method (%u)",
2088 hdev->name, params->limited_cce);
2089 kfree_skb(skb);
2090 return -EINVAL;
2091 }
2092
2093 /* If the OTP has no valid Bluetooth device address, then there will
2094 * also be no valid address for the operational firmware.
2095 */
2096 if (!bacmp(¶ms->otp_bdaddr, BDADDR_ANY)) {
2097 BT_INFO("%s: No device address configured", hdev->name);
2098 set_bit(HCI_QUIRK_INVALID_BDADDR, &hdev->quirks);
2099 }
2100
2101 /* With this Intel bootloader only the hardware variant and device
2102 * revision information are used to select the right firmware.
2103 *
2104 * Currently this bootloader support is limited to hardware variant
2105 * iBT 3.0 (LnP/SfP) which is identified by the value 11 (0x0b).
2106 */
2107 snprintf(fwname, sizeof(fwname), "intel/ibt-11-%u.sfi",
2108 le16_to_cpu(params->dev_revid));
2109
2110 err = request_firmware(&fw, fwname, &hdev->dev);
2111 if (err < 0) {
2112 BT_ERR("%s: Failed to load Intel firmware file (%d)",
2113 hdev->name, err);
2114 kfree_skb(skb);
2115 return err;
2116 }
2117
2118 BT_INFO("%s: Found device firmware: %s", hdev->name, fwname);
2119
2120 /* Save the DDC file name for later use to apply once the firmware
2121 * downloading is done.
2122 */
2123 snprintf(fwname, sizeof(fwname), "intel/ibt-11-%u.ddc",
2124 le16_to_cpu(params->dev_revid));
2125
2126 kfree_skb(skb);
2127
2128 if (fw->size < 644) {
2129 BT_ERR("%s: Invalid size of firmware file (%zu)",
2130 hdev->name, fw->size);
2131 err = -EBADF;
2132 goto done;
2133 }
2134
2135 set_bit(BTUSB_DOWNLOADING, &data->flags);
2136
2137 /* Start the firmware download transaction with the Init fragment
2138 * represented by the 128 bytes of CSS header.
2139 */
2140 err = btintel_secure_send(hdev, 0x00, 128, fw->data);
2141 if (err < 0) {
2142 BT_ERR("%s: Failed to send firmware header (%d)",
2143 hdev->name, err);
2144 goto done;
2145 }
2146
2147 /* Send the 256 bytes of public key information from the firmware
2148 * as the PKey fragment.
2149 */
2150 err = btintel_secure_send(hdev, 0x03, 256, fw->data + 128);
2151 if (err < 0) {
2152 BT_ERR("%s: Failed to send firmware public key (%d)",
2153 hdev->name, err);
2154 goto done;
2155 }
2156
2157 /* Send the 256 bytes of signature information from the firmware
2158 * as the Sign fragment.
2159 */
2160 err = btintel_secure_send(hdev, 0x02, 256, fw->data + 388);
2161 if (err < 0) {
2162 BT_ERR("%s: Failed to send firmware signature (%d)",
2163 hdev->name, err);
2164 goto done;
2165 }
2166
2167 fw_ptr = fw->data + 644;
2168 frag_len = 0;
2169
2170 while (fw_ptr - fw->data < fw->size) {
2171 struct hci_command_hdr *cmd = (void *)(fw_ptr + frag_len);
2172
2173 frag_len += sizeof(*cmd) + cmd->plen;
2174
2175 /* The parameter length of the secure send command requires
2176 * a 4 byte alignment. It happens so that the firmware file
2177 * contains proper Intel_NOP commands to align the fragments
2178 * as needed.
2179 *
2180 * Send set of commands with 4 byte alignment from the
2181 * firmware data buffer as a single Data fragement.
2182 */
2183 if (!(frag_len % 4)) {
2184 err = btintel_secure_send(hdev, 0x01, frag_len, fw_ptr);
2185 if (err < 0) {
2186 BT_ERR("%s: Failed to send firmware data (%d)",
2187 hdev->name, err);
2188 goto done;
2189 }
2190
2191 fw_ptr += frag_len;
2192 frag_len = 0;
2193 }
2194 }
2195
2196 set_bit(BTUSB_FIRMWARE_LOADED, &data->flags);
2197
2198 BT_INFO("%s: Waiting for firmware download to complete", hdev->name);
2199
2200 /* Before switching the device into operational mode and with that
2201 * booting the loaded firmware, wait for the bootloader notification
2202 * that all fragments have been successfully received.
2203 *
2204 * When the event processing receives the notification, then the
2205 * BTUSB_DOWNLOADING flag will be cleared.
2206 *
2207 * The firmware loading should not take longer than 5 seconds
2208 * and thus just timeout if that happens and fail the setup
2209 * of this device.
2210 */
2211 err = wait_on_bit_timeout(&data->flags, BTUSB_DOWNLOADING,
2212 TASK_INTERRUPTIBLE,
2213 msecs_to_jiffies(5000));
2214 if (err == 1) {
2215 BT_ERR("%s: Firmware loading interrupted", hdev->name);
2216 err = -EINTR;
2217 goto done;
2218 }
2219
2220 if (err) {
2221 BT_ERR("%s: Firmware loading timeout", hdev->name);
2222 err = -ETIMEDOUT;
2223 goto done;
2224 }
2225
2226 if (test_bit(BTUSB_FIRMWARE_FAILED, &data->flags)) {
2227 BT_ERR("%s: Firmware loading failed", hdev->name);
2228 err = -ENOEXEC;
2229 goto done;
2230 }
2231
2232 rettime = ktime_get();
2233 delta = ktime_sub(rettime, calltime);
2234 duration = (unsigned long long) ktime_to_ns(delta) >> 10;
2235
2236 BT_INFO("%s: Firmware loaded in %llu usecs", hdev->name, duration);
2237
2238done:
2239 release_firmware(fw);
2240
2241 if (err < 0)
2242 return err;
2243
2244 calltime = ktime_get();
2245
2246 set_bit(BTUSB_BOOTING, &data->flags);
2247
2248 skb = __hci_cmd_sync(hdev, 0xfc01, sizeof(reset_param), reset_param,
2249 HCI_INIT_TIMEOUT);
2250 if (IS_ERR(skb))
2251 return PTR_ERR(skb);
2252
2253 kfree_skb(skb);
2254
2255 /* The bootloader will not indicate when the device is ready. This
2256 * is done by the operational firmware sending bootup notification.
2257 *
2258 * Booting into operational firmware should not take longer than
2259 * 1 second. However if that happens, then just fail the setup
2260 * since something went wrong.
2261 */
2262 BT_INFO("%s: Waiting for device to boot", hdev->name);
2263
2264 err = wait_on_bit_timeout(&data->flags, BTUSB_BOOTING,
2265 TASK_INTERRUPTIBLE,
2266 msecs_to_jiffies(1000));
2267
2268 if (err == 1) {
2269 BT_ERR("%s: Device boot interrupted", hdev->name);
2270 return -EINTR;
2271 }
2272
2273 if (err) {
2274 BT_ERR("%s: Device boot timeout", hdev->name);
2275 return -ETIMEDOUT;
2276 }
2277
2278 rettime = ktime_get();
2279 delta = ktime_sub(rettime, calltime);
2280 duration = (unsigned long long) ktime_to_ns(delta) >> 10;
2281
2282 BT_INFO("%s: Device booted in %llu usecs", hdev->name, duration);
2283
2284 clear_bit(BTUSB_BOOTLOADER, &data->flags);
2285
2286 /* Once the device is running in operational mode, it needs to apply
2287 * the device configuration (DDC) parameters.
2288 *
2289 * The device can work without DDC parameters, so even if it fails
2290 * to load the file, no need to fail the setup.
2291 */
2292 btintel_load_ddc_config(hdev, fwname);
2293
2294 /* Set the event mask for Intel specific vendor events. This enables
2295 * a few extra events that are useful during general operation. It
2296 * does not enable any debugging related events.
2297 *
2298 * The device will function correctly without these events enabled
2299 * and thus no need to fail the setup.
2300 */
2301 btintel_set_event_mask(hdev, false);
2302
2303 return 0;
2304}
2305
2306static int btusb_shutdown_intel(struct hci_dev *hdev)
2307{
2308 struct sk_buff *skb;
2309 long ret;
2310
2311 /* Some platforms have an issue with BT LED when the interface is
2312 * down or BT radio is turned off, which takes 5 seconds to BT LED
2313 * goes off. This command turns off the BT LED immediately.
2314 */
2315 skb = __hci_cmd_sync(hdev, 0xfc3f, 0, NULL, HCI_INIT_TIMEOUT);
2316 if (IS_ERR(skb)) {
2317 ret = PTR_ERR(skb);
2318 BT_ERR("%s: turning off Intel device LED failed (%ld)",
2319 hdev->name, ret);
2320 return ret;
2321 }
2322 kfree_skb(skb);
2323
2324 return 0;
2325}
2326
2327static int btusb_set_bdaddr_marvell(struct hci_dev *hdev,
2328 const bdaddr_t *bdaddr)
2329{
2330 struct sk_buff *skb;
2331 u8 buf[8];
2332 long ret;
2333
2334 buf[0] = 0xfe;
2335 buf[1] = sizeof(bdaddr_t);
2336 memcpy(buf + 2, bdaddr, sizeof(bdaddr_t));
2337
2338 skb = __hci_cmd_sync(hdev, 0xfc22, sizeof(buf), buf, HCI_INIT_TIMEOUT);
2339 if (IS_ERR(skb)) {
2340 ret = PTR_ERR(skb);
2341 BT_ERR("%s: changing Marvell device address failed (%ld)",
2342 hdev->name, ret);
2343 return ret;
2344 }
2345 kfree_skb(skb);
2346
2347 return 0;
2348}
2349
2350static int btusb_set_bdaddr_ath3012(struct hci_dev *hdev,
2351 const bdaddr_t *bdaddr)
2352{
2353 struct sk_buff *skb;
2354 u8 buf[10];
2355 long ret;
2356
2357 buf[0] = 0x01;
2358 buf[1] = 0x01;
2359 buf[2] = 0x00;
2360 buf[3] = sizeof(bdaddr_t);
2361 memcpy(buf + 4, bdaddr, sizeof(bdaddr_t));
2362
2363 skb = __hci_cmd_sync(hdev, 0xfc0b, sizeof(buf), buf, HCI_INIT_TIMEOUT);
2364 if (IS_ERR(skb)) {
2365 ret = PTR_ERR(skb);
2366 BT_ERR("%s: Change address command failed (%ld)",
2367 hdev->name, ret);
2368 return ret;
2369 }
2370 kfree_skb(skb);
2371
2372 return 0;
2373}
2374
2375#define QCA_DFU_PACKET_LEN 4096
2376
2377#define QCA_GET_TARGET_VERSION 0x09
2378#define QCA_CHECK_STATUS 0x05
2379#define QCA_DFU_DOWNLOAD 0x01
2380
2381#define QCA_SYSCFG_UPDATED 0x40
2382#define QCA_PATCH_UPDATED 0x80
2383#define QCA_DFU_TIMEOUT 3000
2384
2385struct qca_version {
2386 __le32 rom_version;
2387 __le32 patch_version;
2388 __le32 ram_version;
2389 __le32 ref_clock;
2390 __u8 reserved[4];
2391} __packed;
2392
2393struct qca_rampatch_version {
2394 __le16 rom_version;
2395 __le16 patch_version;
2396} __packed;
2397
2398struct qca_device_info {
2399 u32 rom_version;
2400 u8 rampatch_hdr; /* length of header in rampatch */
2401 u8 nvm_hdr; /* length of header in NVM */
2402 u8 ver_offset; /* offset of version structure in rampatch */
2403};
2404
2405static const struct qca_device_info qca_devices_table[] = {
2406 { 0x00000100, 20, 4, 10 }, /* Rome 1.0 */
2407 { 0x00000101, 20, 4, 10 }, /* Rome 1.1 */
2408 { 0x00000200, 28, 4, 18 }, /* Rome 2.0 */
2409 { 0x00000201, 28, 4, 18 }, /* Rome 2.1 */
2410 { 0x00000300, 28, 4, 18 }, /* Rome 3.0 */
2411 { 0x00000302, 28, 4, 18 }, /* Rome 3.2 */
2412};
2413
2414static int btusb_qca_send_vendor_req(struct hci_dev *hdev, u8 request,
2415 void *data, u16 size)
2416{
2417 struct btusb_data *btdata = hci_get_drvdata(hdev);
2418 struct usb_device *udev = btdata->udev;
2419 int pipe, err;
2420 u8 *buf;
2421
2422 buf = kmalloc(size, GFP_KERNEL);
2423 if (!buf)
2424 return -ENOMEM;
2425
2426 /* Found some of USB hosts have IOT issues with ours so that we should
2427 * not wait until HCI layer is ready.
2428 */
2429 pipe = usb_rcvctrlpipe(udev, 0);
2430 err = usb_control_msg(udev, pipe, request, USB_TYPE_VENDOR | USB_DIR_IN,
2431 0, 0, buf, size, USB_CTRL_SET_TIMEOUT);
2432 if (err < 0) {
2433 BT_ERR("%s: Failed to access otp area (%d)", hdev->name, err);
2434 goto done;
2435 }
2436
2437 memcpy(data, buf, size);
2438
2439done:
2440 kfree(buf);
2441
2442 return err;
2443}
2444
2445static int btusb_setup_qca_download_fw(struct hci_dev *hdev,
2446 const struct firmware *firmware,
2447 size_t hdr_size)
2448{
2449 struct btusb_data *btdata = hci_get_drvdata(hdev);
2450 struct usb_device *udev = btdata->udev;
2451 size_t count, size, sent = 0;
2452 int pipe, len, err;
2453 u8 *buf;
2454
2455 buf = kmalloc(QCA_DFU_PACKET_LEN, GFP_KERNEL);
2456 if (!buf)
2457 return -ENOMEM;
2458
2459 count = firmware->size;
2460
2461 size = min_t(size_t, count, hdr_size);
2462 memcpy(buf, firmware->data, size);
2463
2464 /* USB patches should go down to controller through USB path
2465 * because binary format fits to go down through USB channel.
2466 * USB control path is for patching headers and USB bulk is for
2467 * patch body.
2468 */
2469 pipe = usb_sndctrlpipe(udev, 0);
2470 err = usb_control_msg(udev, pipe, QCA_DFU_DOWNLOAD, USB_TYPE_VENDOR,
2471 0, 0, buf, size, USB_CTRL_SET_TIMEOUT);
2472 if (err < 0) {
2473 BT_ERR("%s: Failed to send headers (%d)", hdev->name, err);
2474 goto done;
2475 }
2476
2477 sent += size;
2478 count -= size;
2479
2480 while (count) {
2481 size = min_t(size_t, count, QCA_DFU_PACKET_LEN);
2482
2483 memcpy(buf, firmware->data + sent, size);
2484
2485 pipe = usb_sndbulkpipe(udev, 0x02);
2486 err = usb_bulk_msg(udev, pipe, buf, size, &len,
2487 QCA_DFU_TIMEOUT);
2488 if (err < 0) {
2489 BT_ERR("%s: Failed to send body at %zd of %zd (%d)",
2490 hdev->name, sent, firmware->size, err);
2491 break;
2492 }
2493
2494 if (size != len) {
2495 BT_ERR("%s: Failed to get bulk buffer", hdev->name);
2496 err = -EILSEQ;
2497 break;
2498 }
2499
2500 sent += size;
2501 count -= size;
2502 }
2503
2504done:
2505 kfree(buf);
2506 return err;
2507}
2508
2509static int btusb_setup_qca_load_rampatch(struct hci_dev *hdev,
2510 struct qca_version *ver,
2511 const struct qca_device_info *info)
2512{
2513 struct qca_rampatch_version *rver;
2514 const struct firmware *fw;
2515 u32 ver_rom, ver_patch;
2516 u16 rver_rom, rver_patch;
2517 char fwname[64];
2518 int err;
2519
2520 ver_rom = le32_to_cpu(ver->rom_version);
2521 ver_patch = le32_to_cpu(ver->patch_version);
2522
2523 snprintf(fwname, sizeof(fwname), "qca/rampatch_usb_%08x.bin", ver_rom);
2524
2525 err = request_firmware(&fw, fwname, &hdev->dev);
2526 if (err) {
2527 BT_ERR("%s: failed to request rampatch file: %s (%d)",
2528 hdev->name, fwname, err);
2529 return err;
2530 }
2531
2532 BT_INFO("%s: using rampatch file: %s", hdev->name, fwname);
2533
2534 rver = (struct qca_rampatch_version *)(fw->data + info->ver_offset);
2535 rver_rom = le16_to_cpu(rver->rom_version);
2536 rver_patch = le16_to_cpu(rver->patch_version);
2537
2538 BT_INFO("%s: QCA: patch rome 0x%x build 0x%x, firmware rome 0x%x "
2539 "build 0x%x", hdev->name, rver_rom, rver_patch, ver_rom,
2540 ver_patch);
2541
2542 if (rver_rom != ver_rom || rver_patch <= ver_patch) {
2543 BT_ERR("%s: rampatch file version did not match with firmware",
2544 hdev->name);
2545 err = -EINVAL;
2546 goto done;
2547 }
2548
2549 err = btusb_setup_qca_download_fw(hdev, fw, info->rampatch_hdr);
2550
2551done:
2552 release_firmware(fw);
2553
2554 return err;
2555}
2556
2557static int btusb_setup_qca_load_nvm(struct hci_dev *hdev,
2558 struct qca_version *ver,
2559 const struct qca_device_info *info)
2560{
2561 const struct firmware *fw;
2562 char fwname[64];
2563 int err;
2564
2565 snprintf(fwname, sizeof(fwname), "qca/nvm_usb_%08x.bin",
2566 le32_to_cpu(ver->rom_version));
2567
2568 err = request_firmware(&fw, fwname, &hdev->dev);
2569 if (err) {
2570 BT_ERR("%s: failed to request NVM file: %s (%d)",
2571 hdev->name, fwname, err);
2572 return err;
2573 }
2574
2575 BT_INFO("%s: using NVM file: %s", hdev->name, fwname);
2576
2577 err = btusb_setup_qca_download_fw(hdev, fw, info->nvm_hdr);
2578
2579 release_firmware(fw);
2580
2581 return err;
2582}
2583
2584static int btusb_setup_qca(struct hci_dev *hdev)
2585{
2586 const struct qca_device_info *info = NULL;
2587 struct qca_version ver;
2588 u32 ver_rom;
2589 u8 status;
2590 int i, err;
2591
2592 err = btusb_qca_send_vendor_req(hdev, QCA_GET_TARGET_VERSION, &ver,
2593 sizeof(ver));
2594 if (err < 0)
2595 return err;
2596
2597 ver_rom = le32_to_cpu(ver.rom_version);
2598 for (i = 0; i < ARRAY_SIZE(qca_devices_table); i++) {
2599 if (ver_rom == qca_devices_table[i].rom_version)
2600 info = &qca_devices_table[i];
2601 }
2602 if (!info) {
2603 BT_ERR("%s: don't support firmware rome 0x%x", hdev->name,
2604 ver_rom);
2605 return -ENODEV;
2606 }
2607
2608 err = btusb_qca_send_vendor_req(hdev, QCA_CHECK_STATUS, &status,
2609 sizeof(status));
2610 if (err < 0)
2611 return err;
2612
2613 if (!(status & QCA_PATCH_UPDATED)) {
2614 err = btusb_setup_qca_load_rampatch(hdev, &ver, info);
2615 if (err < 0)
2616 return err;
2617 }
2618
2619 if (!(status & QCA_SYSCFG_UPDATED)) {
2620 err = btusb_setup_qca_load_nvm(hdev, &ver, info);
2621 if (err < 0)
2622 return err;
2623 }
2624
2625 return 0;
2626}
2627
2628#ifdef CONFIG_BT_HCIBTUSB_BCM
2629static inline int __set_diag_interface(struct hci_dev *hdev)
2630{
2631 struct btusb_data *data = hci_get_drvdata(hdev);
2632 struct usb_interface *intf = data->diag;
2633 int i;
2634
2635 if (!data->diag)
2636 return -ENODEV;
2637
2638 data->diag_tx_ep = NULL;
2639 data->diag_rx_ep = NULL;
2640
2641 for (i = 0; i < intf->cur_altsetting->desc.bNumEndpoints; i++) {
2642 struct usb_endpoint_descriptor *ep_desc;
2643
2644 ep_desc = &intf->cur_altsetting->endpoint[i].desc;
2645
2646 if (!data->diag_tx_ep && usb_endpoint_is_bulk_out(ep_desc)) {
2647 data->diag_tx_ep = ep_desc;
2648 continue;
2649 }
2650
2651 if (!data->diag_rx_ep && usb_endpoint_is_bulk_in(ep_desc)) {
2652 data->diag_rx_ep = ep_desc;
2653 continue;
2654 }
2655 }
2656
2657 if (!data->diag_tx_ep || !data->diag_rx_ep) {
2658 BT_ERR("%s invalid diagnostic descriptors", hdev->name);
2659 return -ENODEV;
2660 }
2661
2662 return 0;
2663}
2664
2665static struct urb *alloc_diag_urb(struct hci_dev *hdev, bool enable)
2666{
2667 struct btusb_data *data = hci_get_drvdata(hdev);
2668 struct sk_buff *skb;
2669 struct urb *urb;
2670 unsigned int pipe;
2671
2672 if (!data->diag_tx_ep)
2673 return ERR_PTR(-ENODEV);
2674
2675 urb = usb_alloc_urb(0, GFP_KERNEL);
2676 if (!urb)
2677 return ERR_PTR(-ENOMEM);
2678
2679 skb = bt_skb_alloc(2, GFP_KERNEL);
2680 if (!skb) {
2681 usb_free_urb(urb);
2682 return ERR_PTR(-ENOMEM);
2683 }
2684
2685 *skb_put(skb, 1) = 0xf0;
2686 *skb_put(skb, 1) = enable;
2687
2688 pipe = usb_sndbulkpipe(data->udev, data->diag_tx_ep->bEndpointAddress);
2689
2690 usb_fill_bulk_urb(urb, data->udev, pipe,
2691 skb->data, skb->len, btusb_tx_complete, skb);
2692
2693 skb->dev = (void *)hdev;
2694
2695 return urb;
2696}
2697
2698static int btusb_bcm_set_diag(struct hci_dev *hdev, bool enable)
2699{
2700 struct btusb_data *data = hci_get_drvdata(hdev);
2701 struct urb *urb;
2702
2703 if (!data->diag)
2704 return -ENODEV;
2705
2706 if (!test_bit(HCI_RUNNING, &hdev->flags))
2707 return -ENETDOWN;
2708
2709 urb = alloc_diag_urb(hdev, enable);
2710 if (IS_ERR(urb))
2711 return PTR_ERR(urb);
2712
2713 return submit_or_queue_tx_urb(hdev, urb);
2714}
2715#endif
2716
2717static int btusb_probe(struct usb_interface *intf,
2718 const struct usb_device_id *id)
2719{
2720 struct usb_endpoint_descriptor *ep_desc;
2721 struct btusb_data *data;
2722 struct hci_dev *hdev;
2723 unsigned ifnum_base;
2724 int i, err;
2725
2726 BT_DBG("intf %p id %p", intf, id);
2727
2728 /* interface numbers are hardcoded in the spec */
2729 if (intf->cur_altsetting->desc.bInterfaceNumber != 0) {
2730 if (!(id->driver_info & BTUSB_IFNUM_2))
2731 return -ENODEV;
2732 if (intf->cur_altsetting->desc.bInterfaceNumber != 2)
2733 return -ENODEV;
2734 }
2735
2736 ifnum_base = intf->cur_altsetting->desc.bInterfaceNumber;
2737
2738 if (!id->driver_info) {
2739 const struct usb_device_id *match;
2740
2741 match = usb_match_id(intf, blacklist_table);
2742 if (match)
2743 id = match;
2744 }
2745
2746 if (id->driver_info == BTUSB_IGNORE)
2747 return -ENODEV;
2748
2749 if (id->driver_info & BTUSB_ATH3012) {
2750 struct usb_device *udev = interface_to_usbdev(intf);
2751
2752 /* Old firmware would otherwise let ath3k driver load
2753 * patch and sysconfig files */
2754 if (le16_to_cpu(udev->descriptor.bcdDevice) <= 0x0001)
2755 return -ENODEV;
2756 }
2757
2758 data = devm_kzalloc(&intf->dev, sizeof(*data), GFP_KERNEL);
2759 if (!data)
2760 return -ENOMEM;
2761
2762 for (i = 0; i < intf->cur_altsetting->desc.bNumEndpoints; i++) {
2763 ep_desc = &intf->cur_altsetting->endpoint[i].desc;
2764
2765 if (!data->intr_ep && usb_endpoint_is_int_in(ep_desc)) {
2766 data->intr_ep = ep_desc;
2767 continue;
2768 }
2769
2770 if (!data->bulk_tx_ep && usb_endpoint_is_bulk_out(ep_desc)) {
2771 data->bulk_tx_ep = ep_desc;
2772 continue;
2773 }
2774
2775 if (!data->bulk_rx_ep && usb_endpoint_is_bulk_in(ep_desc)) {
2776 data->bulk_rx_ep = ep_desc;
2777 continue;
2778 }
2779 }
2780
2781 if (!data->intr_ep || !data->bulk_tx_ep || !data->bulk_rx_ep)
2782 return -ENODEV;
2783
2784 if (id->driver_info & BTUSB_AMP) {
2785 data->cmdreq_type = USB_TYPE_CLASS | 0x01;
2786 data->cmdreq = 0x2b;
2787 } else {
2788 data->cmdreq_type = USB_TYPE_CLASS;
2789 data->cmdreq = 0x00;
2790 }
2791
2792 data->udev = interface_to_usbdev(intf);
2793 data->intf = intf;
2794
2795 INIT_WORK(&data->work, btusb_work);
2796 INIT_WORK(&data->waker, btusb_waker);
2797 init_usb_anchor(&data->deferred);
2798 init_usb_anchor(&data->tx_anchor);
2799 spin_lock_init(&data->txlock);
2800
2801 init_usb_anchor(&data->intr_anchor);
2802 init_usb_anchor(&data->bulk_anchor);
2803 init_usb_anchor(&data->isoc_anchor);
2804 init_usb_anchor(&data->diag_anchor);
2805 spin_lock_init(&data->rxlock);
2806
2807 if (id->driver_info & BTUSB_INTEL_NEW) {
2808 data->recv_event = btusb_recv_event_intel;
2809 data->recv_bulk = btusb_recv_bulk_intel;
2810 set_bit(BTUSB_BOOTLOADER, &data->flags);
2811 } else {
2812 data->recv_event = hci_recv_frame;
2813 data->recv_bulk = btusb_recv_bulk;
2814 }
2815
2816 hdev = hci_alloc_dev();
2817 if (!hdev)
2818 return -ENOMEM;
2819
2820 hdev->bus = HCI_USB;
2821 hci_set_drvdata(hdev, data);
2822
2823 if (id->driver_info & BTUSB_AMP)
2824 hdev->dev_type = HCI_AMP;
2825 else
2826 hdev->dev_type = HCI_BREDR;
2827
2828 data->hdev = hdev;
2829
2830 SET_HCIDEV_DEV(hdev, &intf->dev);
2831
2832 hdev->open = btusb_open;
2833 hdev->close = btusb_close;
2834 hdev->flush = btusb_flush;
2835 hdev->send = btusb_send_frame;
2836 hdev->notify = btusb_notify;
2837
2838 if (id->driver_info & BTUSB_BCM2045)
2839 set_bit(HCI_QUIRK_BROKEN_STORED_LINK_KEY, &hdev->quirks);
2840
2841 if (id->driver_info & BTUSB_BCM92035)
2842 hdev->setup = btusb_setup_bcm92035;
2843
2844#ifdef CONFIG_BT_HCIBTUSB_BCM
2845 if (id->driver_info & BTUSB_BCM_PATCHRAM) {
2846 hdev->manufacturer = 15;
2847 hdev->setup = btbcm_setup_patchram;
2848 hdev->set_diag = btusb_bcm_set_diag;
2849 hdev->set_bdaddr = btbcm_set_bdaddr;
2850
2851 /* Broadcom LM_DIAG Interface numbers are hardcoded */
2852 data->diag = usb_ifnum_to_if(data->udev, ifnum_base + 2);
2853 }
2854
2855 if (id->driver_info & BTUSB_BCM_APPLE) {
2856 hdev->manufacturer = 15;
2857 hdev->setup = btbcm_setup_apple;
2858 hdev->set_diag = btusb_bcm_set_diag;
2859
2860 /* Broadcom LM_DIAG Interface numbers are hardcoded */
2861 data->diag = usb_ifnum_to_if(data->udev, ifnum_base + 2);
2862 }
2863#endif
2864
2865 if (id->driver_info & BTUSB_INTEL) {
2866 hdev->manufacturer = 2;
2867 hdev->setup = btusb_setup_intel;
2868 hdev->shutdown = btusb_shutdown_intel;
2869 hdev->set_diag = btintel_set_diag_mfg;
2870 hdev->set_bdaddr = btintel_set_bdaddr;
2871 set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
2872 set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
2873 set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
2874 }
2875
2876 if (id->driver_info & BTUSB_INTEL_NEW) {
2877 hdev->manufacturer = 2;
2878 hdev->send = btusb_send_frame_intel;
2879 hdev->setup = btusb_setup_intel_new;
2880 hdev->hw_error = btintel_hw_error;
2881 hdev->set_diag = btintel_set_diag;
2882 hdev->set_bdaddr = btintel_set_bdaddr;
2883 set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
2884 set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
2885 }
2886
2887 if (id->driver_info & BTUSB_MARVELL)
2888 hdev->set_bdaddr = btusb_set_bdaddr_marvell;
2889
2890 if (id->driver_info & BTUSB_SWAVE) {
2891 set_bit(HCI_QUIRK_FIXUP_INQUIRY_MODE, &hdev->quirks);
2892 set_bit(HCI_QUIRK_BROKEN_LOCAL_COMMANDS, &hdev->quirks);
2893 }
2894
2895 if (id->driver_info & BTUSB_INTEL_BOOT) {
2896 hdev->manufacturer = 2;
2897 set_bit(HCI_QUIRK_RAW_DEVICE, &hdev->quirks);
2898 }
2899
2900 if (id->driver_info & BTUSB_ATH3012) {
2901 hdev->set_bdaddr = btusb_set_bdaddr_ath3012;
2902 set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
2903 set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
2904 }
2905
2906 if (id->driver_info & BTUSB_QCA_ROME) {
2907 data->setup_on_usb = btusb_setup_qca;
2908 hdev->set_bdaddr = btusb_set_bdaddr_ath3012;
2909 }
2910
2911#ifdef CONFIG_BT_HCIBTUSB_RTL
2912 if (id->driver_info & BTUSB_REALTEK) {
2913 hdev->setup = btrtl_setup_realtek;
2914
2915 /* Realtek devices lose their updated firmware over suspend,
2916 * but the USB hub doesn't notice any status change.
2917 * Explicitly request a device reset on resume.
2918 */
2919 set_bit(BTUSB_RESET_RESUME, &data->flags);
2920 }
2921#endif
2922
2923 if (id->driver_info & BTUSB_AMP) {
2924 /* AMP controllers do not support SCO packets */
2925 data->isoc = NULL;
2926 } else {
2927 /* Interface orders are hardcoded in the specification */
2928 data->isoc = usb_ifnum_to_if(data->udev, ifnum_base + 1);
2929 }
2930
2931 if (!reset)
2932 set_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
2933
2934 if (force_scofix || id->driver_info & BTUSB_WRONG_SCO_MTU) {
2935 if (!disable_scofix)
2936 set_bit(HCI_QUIRK_FIXUP_BUFFER_SIZE, &hdev->quirks);
2937 }
2938
2939 if (id->driver_info & BTUSB_BROKEN_ISOC)
2940 data->isoc = NULL;
2941
2942 if (id->driver_info & BTUSB_DIGIANSWER) {
2943 data->cmdreq_type = USB_TYPE_VENDOR;
2944 set_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
2945 }
2946
2947 if (id->driver_info & BTUSB_CSR) {
2948 struct usb_device *udev = data->udev;
2949 u16 bcdDevice = le16_to_cpu(udev->descriptor.bcdDevice);
2950
2951 /* Old firmware would otherwise execute USB reset */
2952 if (bcdDevice < 0x117)
2953 set_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
2954
2955 /* Fake CSR devices with broken commands */
2956 if (bcdDevice <= 0x100 || bcdDevice == 0x134)
2957 hdev->setup = btusb_setup_csr;
2958
2959 set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
2960 }
2961
2962 if (id->driver_info & BTUSB_SNIFFER) {
2963 struct usb_device *udev = data->udev;
2964
2965 /* New sniffer firmware has crippled HCI interface */
2966 if (le16_to_cpu(udev->descriptor.bcdDevice) > 0x997)
2967 set_bit(HCI_QUIRK_RAW_DEVICE, &hdev->quirks);
2968 }
2969
2970 if (id->driver_info & BTUSB_INTEL_BOOT) {
2971 /* A bug in the bootloader causes that interrupt interface is
2972 * only enabled after receiving SetInterface(0, AltSetting=0).
2973 */
2974 err = usb_set_interface(data->udev, 0, 0);
2975 if (err < 0) {
2976 BT_ERR("failed to set interface 0, alt 0 %d", err);
2977 hci_free_dev(hdev);
2978 return err;
2979 }
2980 }
2981
2982 if (data->isoc) {
2983 err = usb_driver_claim_interface(&btusb_driver,
2984 data->isoc, data);
2985 if (err < 0) {
2986 hci_free_dev(hdev);
2987 return err;
2988 }
2989 }
2990
2991#ifdef CONFIG_BT_HCIBTUSB_BCM
2992 if (data->diag) {
2993 if (!usb_driver_claim_interface(&btusb_driver,
2994 data->diag, data))
2995 __set_diag_interface(hdev);
2996 else
2997 data->diag = NULL;
2998 }
2999#endif
3000
3001 err = hci_register_dev(hdev);
3002 if (err < 0) {
3003 hci_free_dev(hdev);
3004 return err;
3005 }
3006
3007 usb_set_intfdata(intf, data);
3008
3009 return 0;
3010}
3011
3012static void btusb_disconnect(struct usb_interface *intf)
3013{
3014 struct btusb_data *data = usb_get_intfdata(intf);
3015 struct hci_dev *hdev;
3016
3017 BT_DBG("intf %p", intf);
3018
3019 if (!data)
3020 return;
3021
3022 hdev = data->hdev;
3023 usb_set_intfdata(data->intf, NULL);
3024
3025 if (data->isoc)
3026 usb_set_intfdata(data->isoc, NULL);
3027
3028 if (data->diag)
3029 usb_set_intfdata(data->diag, NULL);
3030
3031 hci_unregister_dev(hdev);
3032
3033 if (intf == data->intf) {
3034 if (data->isoc)
3035 usb_driver_release_interface(&btusb_driver, data->isoc);
3036 if (data->diag)
3037 usb_driver_release_interface(&btusb_driver, data->diag);
3038 } else if (intf == data->isoc) {
3039 if (data->diag)
3040 usb_driver_release_interface(&btusb_driver, data->diag);
3041 usb_driver_release_interface(&btusb_driver, data->intf);
3042 } else if (intf == data->diag) {
3043 usb_driver_release_interface(&btusb_driver, data->intf);
3044 if (data->isoc)
3045 usb_driver_release_interface(&btusb_driver, data->isoc);
3046 }
3047
3048 hci_free_dev(hdev);
3049}
3050
3051#ifdef CONFIG_PM
3052static int btusb_suspend(struct usb_interface *intf, pm_message_t message)
3053{
3054 struct btusb_data *data = usb_get_intfdata(intf);
3055
3056 BT_DBG("intf %p", intf);
3057
3058 if (data->suspend_count++)
3059 return 0;
3060
3061 spin_lock_irq(&data->txlock);
3062 if (!(PMSG_IS_AUTO(message) && data->tx_in_flight)) {
3063 set_bit(BTUSB_SUSPENDING, &data->flags);
3064 spin_unlock_irq(&data->txlock);
3065 } else {
3066 spin_unlock_irq(&data->txlock);
3067 data->suspend_count--;
3068 return -EBUSY;
3069 }
3070
3071 cancel_work_sync(&data->work);
3072
3073 btusb_stop_traffic(data);
3074 usb_kill_anchored_urbs(&data->tx_anchor);
3075
3076 /* Optionally request a device reset on resume, but only when
3077 * wakeups are disabled. If wakeups are enabled we assume the
3078 * device will stay powered up throughout suspend.
3079 */
3080 if (test_bit(BTUSB_RESET_RESUME, &data->flags) &&
3081 !device_may_wakeup(&data->udev->dev))
3082 data->udev->reset_resume = 1;
3083
3084 return 0;
3085}
3086
3087static void play_deferred(struct btusb_data *data)
3088{
3089 struct urb *urb;
3090 int err;
3091
3092 while ((urb = usb_get_from_anchor(&data->deferred))) {
3093 err = usb_submit_urb(urb, GFP_ATOMIC);
3094 if (err < 0)
3095 break;
3096
3097 data->tx_in_flight++;
3098 }
3099 usb_scuttle_anchored_urbs(&data->deferred);
3100}
3101
3102static int btusb_resume(struct usb_interface *intf)
3103{
3104 struct btusb_data *data = usb_get_intfdata(intf);
3105 struct hci_dev *hdev = data->hdev;
3106 int err = 0;
3107
3108 BT_DBG("intf %p", intf);
3109
3110 if (--data->suspend_count)
3111 return 0;
3112
3113 if (!test_bit(HCI_RUNNING, &hdev->flags))
3114 goto done;
3115
3116 if (test_bit(BTUSB_INTR_RUNNING, &data->flags)) {
3117 err = btusb_submit_intr_urb(hdev, GFP_NOIO);
3118 if (err < 0) {
3119 clear_bit(BTUSB_INTR_RUNNING, &data->flags);
3120 goto failed;
3121 }
3122 }
3123
3124 if (test_bit(BTUSB_BULK_RUNNING, &data->flags)) {
3125 err = btusb_submit_bulk_urb(hdev, GFP_NOIO);
3126 if (err < 0) {
3127 clear_bit(BTUSB_BULK_RUNNING, &data->flags);
3128 goto failed;
3129 }
3130
3131 btusb_submit_bulk_urb(hdev, GFP_NOIO);
3132 }
3133
3134 if (test_bit(BTUSB_ISOC_RUNNING, &data->flags)) {
3135 if (btusb_submit_isoc_urb(hdev, GFP_NOIO) < 0)
3136 clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
3137 else
3138 btusb_submit_isoc_urb(hdev, GFP_NOIO);
3139 }
3140
3141 spin_lock_irq(&data->txlock);
3142 play_deferred(data);
3143 clear_bit(BTUSB_SUSPENDING, &data->flags);
3144 spin_unlock_irq(&data->txlock);
3145 schedule_work(&data->work);
3146
3147 return 0;
3148
3149failed:
3150 usb_scuttle_anchored_urbs(&data->deferred);
3151done:
3152 spin_lock_irq(&data->txlock);
3153 clear_bit(BTUSB_SUSPENDING, &data->flags);
3154 spin_unlock_irq(&data->txlock);
3155
3156 return err;
3157}
3158#endif
3159
3160static struct usb_driver btusb_driver = {
3161 .name = "btusb",
3162 .probe = btusb_probe,
3163 .disconnect = btusb_disconnect,
3164#ifdef CONFIG_PM
3165 .suspend = btusb_suspend,
3166 .resume = btusb_resume,
3167#endif
3168 .id_table = btusb_table,
3169 .supports_autosuspend = 1,
3170 .disable_hub_initiated_lpm = 1,
3171};
3172
3173module_usb_driver(btusb_driver);
3174
3175module_param(disable_scofix, bool, 0644);
3176MODULE_PARM_DESC(disable_scofix, "Disable fixup of wrong SCO buffer size");
3177
3178module_param(force_scofix, bool, 0644);
3179MODULE_PARM_DESC(force_scofix, "Force fixup of wrong SCO buffers size");
3180
3181module_param(reset, bool, 0644);
3182MODULE_PARM_DESC(reset, "Send HCI reset command on initialization");
3183
3184MODULE_AUTHOR("Marcel Holtmann <marcel@holtmann.org>");
3185MODULE_DESCRIPTION("Generic Bluetooth USB driver ver " VERSION);
3186MODULE_VERSION(VERSION);
3187MODULE_LICENSE("GPL");