Loading...
Note: File does not exist in v6.13.7.
1#ifndef B43_H_
2#define B43_H_
3
4#include <linux/kernel.h>
5#include <linux/spinlock.h>
6#include <linux/interrupt.h>
7#include <linux/hw_random.h>
8#include <linux/bcma/bcma.h>
9#include <linux/ssb/ssb.h>
10#include <net/mac80211.h>
11
12#include "debugfs.h"
13#include "leds.h"
14#include "rfkill.h"
15#include "bus.h"
16#include "lo.h"
17#include "phy_common.h"
18
19
20#ifdef CONFIG_B43_DEBUG
21# define B43_DEBUG 1
22#else
23# define B43_DEBUG 0
24#endif
25
26/* MMIO offsets */
27#define B43_MMIO_DMA0_REASON 0x20
28#define B43_MMIO_DMA0_IRQ_MASK 0x24
29#define B43_MMIO_DMA1_REASON 0x28
30#define B43_MMIO_DMA1_IRQ_MASK 0x2C
31#define B43_MMIO_DMA2_REASON 0x30
32#define B43_MMIO_DMA2_IRQ_MASK 0x34
33#define B43_MMIO_DMA3_REASON 0x38
34#define B43_MMIO_DMA3_IRQ_MASK 0x3C
35#define B43_MMIO_DMA4_REASON 0x40
36#define B43_MMIO_DMA4_IRQ_MASK 0x44
37#define B43_MMIO_DMA5_REASON 0x48
38#define B43_MMIO_DMA5_IRQ_MASK 0x4C
39#define B43_MMIO_MACCTL 0x120 /* MAC control */
40#define B43_MMIO_MACCMD 0x124 /* MAC command */
41#define B43_MMIO_GEN_IRQ_REASON 0x128
42#define B43_MMIO_GEN_IRQ_MASK 0x12C
43#define B43_MMIO_RAM_CONTROL 0x130
44#define B43_MMIO_RAM_DATA 0x134
45#define B43_MMIO_PS_STATUS 0x140
46#define B43_MMIO_RADIO_HWENABLED_HI 0x158
47#define B43_MMIO_SHM_CONTROL 0x160
48#define B43_MMIO_SHM_DATA 0x164
49#define B43_MMIO_SHM_DATA_UNALIGNED 0x166
50#define B43_MMIO_XMITSTAT_0 0x170
51#define B43_MMIO_XMITSTAT_1 0x174
52#define B43_MMIO_REV3PLUS_TSF_LOW 0x180 /* core rev >= 3 only */
53#define B43_MMIO_REV3PLUS_TSF_HIGH 0x184 /* core rev >= 3 only */
54#define B43_MMIO_TSF_CFP_REP 0x188
55#define B43_MMIO_TSF_CFP_START 0x18C
56#define B43_MMIO_TSF_CFP_MAXDUR 0x190
57
58/* 32-bit DMA */
59#define B43_MMIO_DMA32_BASE0 0x200
60#define B43_MMIO_DMA32_BASE1 0x220
61#define B43_MMIO_DMA32_BASE2 0x240
62#define B43_MMIO_DMA32_BASE3 0x260
63#define B43_MMIO_DMA32_BASE4 0x280
64#define B43_MMIO_DMA32_BASE5 0x2A0
65/* 64-bit DMA */
66#define B43_MMIO_DMA64_BASE0 0x200
67#define B43_MMIO_DMA64_BASE1 0x240
68#define B43_MMIO_DMA64_BASE2 0x280
69#define B43_MMIO_DMA64_BASE3 0x2C0
70#define B43_MMIO_DMA64_BASE4 0x300
71#define B43_MMIO_DMA64_BASE5 0x340
72
73/* PIO on core rev < 11 */
74#define B43_MMIO_PIO_BASE0 0x300
75#define B43_MMIO_PIO_BASE1 0x310
76#define B43_MMIO_PIO_BASE2 0x320
77#define B43_MMIO_PIO_BASE3 0x330
78#define B43_MMIO_PIO_BASE4 0x340
79#define B43_MMIO_PIO_BASE5 0x350
80#define B43_MMIO_PIO_BASE6 0x360
81#define B43_MMIO_PIO_BASE7 0x370
82/* PIO on core rev >= 11 */
83#define B43_MMIO_PIO11_BASE0 0x200
84#define B43_MMIO_PIO11_BASE1 0x240
85#define B43_MMIO_PIO11_BASE2 0x280
86#define B43_MMIO_PIO11_BASE3 0x2C0
87#define B43_MMIO_PIO11_BASE4 0x300
88#define B43_MMIO_PIO11_BASE5 0x340
89
90#define B43_MMIO_RADIO24_CONTROL 0x3D8 /* core rev >= 24 only */
91#define B43_MMIO_RADIO24_DATA 0x3DA /* core rev >= 24 only */
92#define B43_MMIO_PHY_VER 0x3E0
93#define B43_MMIO_PHY_RADIO 0x3E2
94#define B43_MMIO_PHY0 0x3E6
95#define B43_MMIO_ANTENNA 0x3E8
96#define B43_MMIO_CHANNEL 0x3F0
97#define B43_MMIO_CHANNEL_EXT 0x3F4
98#define B43_MMIO_RADIO_CONTROL 0x3F6
99#define B43_MMIO_RADIO_DATA_HIGH 0x3F8
100#define B43_MMIO_RADIO_DATA_LOW 0x3FA
101#define B43_MMIO_PHY_CONTROL 0x3FC
102#define B43_MMIO_PHY_DATA 0x3FE
103#define B43_MMIO_MACFILTER_CONTROL 0x420
104#define B43_MMIO_MACFILTER_DATA 0x422
105#define B43_MMIO_RCMTA_COUNT 0x43C
106#define B43_MMIO_PSM_PHY_HDR 0x492
107#define B43_MMIO_RADIO_HWENABLED_LO 0x49A
108#define B43_MMIO_GPIO_CONTROL 0x49C
109#define B43_MMIO_GPIO_MASK 0x49E
110#define B43_MMIO_TXE0_CTL 0x500
111#define B43_MMIO_TXE0_AUX 0x502
112#define B43_MMIO_TXE0_TS_LOC 0x504
113#define B43_MMIO_TXE0_TIME_OUT 0x506
114#define B43_MMIO_TXE0_WM_0 0x508
115#define B43_MMIO_TXE0_WM_1 0x50A
116#define B43_MMIO_TXE0_PHYCTL 0x50C
117#define B43_MMIO_TXE0_STATUS 0x50E
118#define B43_MMIO_TXE0_MMPLCP0 0x510
119#define B43_MMIO_TXE0_MMPLCP1 0x512
120#define B43_MMIO_TXE0_PHYCTL1 0x514
121#define B43_MMIO_XMTFIFODEF 0x520
122#define B43_MMIO_XMTFIFO_FRAME_CNT 0x522 /* core rev>= 16 only */
123#define B43_MMIO_XMTFIFO_BYTE_CNT 0x524 /* core rev>= 16 only */
124#define B43_MMIO_XMTFIFO_HEAD 0x526 /* core rev>= 16 only */
125#define B43_MMIO_XMTFIFO_RD_PTR 0x528 /* core rev>= 16 only */
126#define B43_MMIO_XMTFIFO_WR_PTR 0x52A /* core rev>= 16 only */
127#define B43_MMIO_XMTFIFODEF1 0x52C /* core rev>= 16 only */
128#define B43_MMIO_XMTFIFOCMD 0x540
129#define B43_MMIO_XMTFIFOFLUSH 0x542
130#define B43_MMIO_XMTFIFOTHRESH 0x544
131#define B43_MMIO_XMTFIFORDY 0x546
132#define B43_MMIO_XMTFIFOPRIRDY 0x548
133#define B43_MMIO_XMTFIFORQPRI 0x54A
134#define B43_MMIO_XMTTPLATETXPTR 0x54C
135#define B43_MMIO_XMTTPLATEPTR 0x550
136#define B43_MMIO_SMPL_CLCT_STRPTR 0x552 /* core rev>= 22 only */
137#define B43_MMIO_SMPL_CLCT_STPPTR 0x554 /* core rev>= 22 only */
138#define B43_MMIO_SMPL_CLCT_CURPTR 0x556 /* core rev>= 22 only */
139#define B43_MMIO_XMTTPLATEDATALO 0x560
140#define B43_MMIO_XMTTPLATEDATAHI 0x562
141#define B43_MMIO_XMTSEL 0x568
142#define B43_MMIO_XMTTXCNT 0x56A
143#define B43_MMIO_XMTTXSHMADDR 0x56C
144#define B43_MMIO_TSF_CFP_START_LOW 0x604
145#define B43_MMIO_TSF_CFP_START_HIGH 0x606
146#define B43_MMIO_TSF_CFP_PRETBTT 0x612
147#define B43_MMIO_TSF_CLK_FRAC_LOW 0x62E
148#define B43_MMIO_TSF_CLK_FRAC_HIGH 0x630
149#define B43_MMIO_TSF_0 0x632 /* core rev < 3 only */
150#define B43_MMIO_TSF_1 0x634 /* core rev < 3 only */
151#define B43_MMIO_TSF_2 0x636 /* core rev < 3 only */
152#define B43_MMIO_TSF_3 0x638 /* core rev < 3 only */
153#define B43_MMIO_RNG 0x65A
154#define B43_MMIO_IFSSLOT 0x684 /* Interframe slot time */
155#define B43_MMIO_IFSCTL 0x688 /* Interframe space control */
156#define B43_MMIO_IFSSTAT 0x690
157#define B43_MMIO_IFSMEDBUSYCTL 0x692
158#define B43_MMIO_IFTXDUR 0x694
159#define B43_MMIO_IFSCTL_USE_EDCF 0x0004
160#define B43_MMIO_POWERUP_DELAY 0x6A8
161#define B43_MMIO_BTCOEX_CTL 0x6B4 /* Bluetooth Coexistence Control */
162#define B43_MMIO_BTCOEX_STAT 0x6B6 /* Bluetooth Coexistence Status */
163#define B43_MMIO_BTCOEX_TXCTL 0x6B8 /* Bluetooth Coexistence Transmit Control */
164#define B43_MMIO_WEPCTL 0x7C0
165
166/* SPROM boardflags_lo values */
167#define B43_BFL_BTCOEXIST 0x0001 /* implements Bluetooth coexistance */
168#define B43_BFL_PACTRL 0x0002 /* GPIO 9 controlling the PA */
169#define B43_BFL_AIRLINEMODE 0x0004 /* implements GPIO 13 radio disable indication */
170#define B43_BFL_RSSI 0x0008 /* software calculates nrssi slope. */
171#define B43_BFL_ENETSPI 0x0010 /* has ephy roboswitch spi */
172#define B43_BFL_XTAL_NOSLOW 0x0020 /* no slow clock available */
173#define B43_BFL_CCKHIPWR 0x0040 /* can do high power CCK transmission */
174#define B43_BFL_ENETADM 0x0080 /* has ADMtek switch */
175#define B43_BFL_ENETVLAN 0x0100 /* can do vlan */
176#define B43_BFL_AFTERBURNER 0x0200 /* supports Afterburner mode */
177#define B43_BFL_NOPCI 0x0400 /* leaves PCI floating */
178#define B43_BFL_FEM 0x0800 /* supports the Front End Module */
179#define B43_BFL_EXTLNA 0x1000 /* has an external LNA */
180#define B43_BFL_HGPA 0x2000 /* had high gain PA */
181#define B43_BFL_BTCMOD 0x4000 /* BFL_BTCOEXIST is given in alternate GPIOs */
182#define B43_BFL_ALTIQ 0x8000 /* alternate I/Q settings */
183
184/* SPROM boardflags_hi values */
185#define B43_BFH_NOPA 0x0001 /* has no PA */
186#define B43_BFH_RSSIINV 0x0002 /* RSSI uses positive slope (not TSSI) */
187#define B43_BFH_PAREF 0x0004 /* uses the PARef LDO */
188#define B43_BFH_3TSWITCH 0x0008 /* uses a triple throw switch shared
189 * with bluetooth */
190#define B43_BFH_PHASESHIFT 0x0010 /* can support phase shifter */
191#define B43_BFH_BUCKBOOST 0x0020 /* has buck/booster */
192#define B43_BFH_FEM_BT 0x0040 /* has FEM and switch to share antenna
193 * with bluetooth */
194#define B43_BFH_NOCBUCK 0x0080
195#define B43_BFH_PALDO 0x0200
196#define B43_BFH_EXTLNA_5GHZ 0x1000 /* has an external LNA (5GHz mode) */
197
198/* SPROM boardflags2_lo values */
199#define B43_BFL2_RXBB_INT_REG_DIS 0x0001 /* external RX BB regulator present */
200#define B43_BFL2_APLL_WAR 0x0002 /* alternative A-band PLL settings implemented */
201#define B43_BFL2_TXPWRCTRL_EN 0x0004 /* permits enabling TX Power Control */
202#define B43_BFL2_2X4_DIV 0x0008 /* 2x4 diversity switch */
203#define B43_BFL2_5G_PWRGAIN 0x0010 /* supports 5G band power gain */
204#define B43_BFL2_PCIEWAR_OVR 0x0020 /* overrides ASPM and Clkreq settings */
205#define B43_BFL2_CAESERS_BRD 0x0040 /* is Caesers board (unused) */
206#define B43_BFL2_BTC3WIRE 0x0080 /* used 3-wire bluetooth coexist */
207#define B43_BFL2_SKWRKFEM_BRD 0x0100 /* 4321mcm93 uses Skyworks FEM */
208#define B43_BFL2_SPUR_WAR 0x0200 /* has a workaround for clock-harmonic spurs */
209#define B43_BFL2_GPLL_WAR 0x0400 /* altenative G-band PLL settings implemented */
210#define B43_BFL2_SINGLEANT_CCK 0x1000
211#define B43_BFL2_2G_SPUR_WAR 0x2000
212
213/* SPROM boardflags2_hi values */
214#define B43_BFH2_GPLL_WAR2 0x0001
215#define B43_BFH2_IPALVLSHIFT_3P3 0x0002
216#define B43_BFH2_INTERNDET_TXIQCAL 0x0004
217#define B43_BFH2_XTALBUFOUTEN 0x0008
218
219/* GPIO register offset, in both ChipCommon and PCI core. */
220#define B43_GPIO_CONTROL 0x6c
221
222/* SHM Routing */
223enum {
224 B43_SHM_UCODE, /* Microcode memory */
225 B43_SHM_SHARED, /* Shared memory */
226 B43_SHM_SCRATCH, /* Scratch memory */
227 B43_SHM_HW, /* Internal hardware register */
228 B43_SHM_RCMTA, /* Receive match transmitter address (rev >= 5 only) */
229};
230/* SHM Routing modifiers */
231#define B43_SHM_AUTOINC_R 0x0200 /* Auto-increment address on read */
232#define B43_SHM_AUTOINC_W 0x0100 /* Auto-increment address on write */
233#define B43_SHM_AUTOINC_RW (B43_SHM_AUTOINC_R | \
234 B43_SHM_AUTOINC_W)
235
236/* Misc SHM_SHARED offsets */
237#define B43_SHM_SH_WLCOREREV 0x0016 /* 802.11 core revision */
238#define B43_SHM_SH_PCTLWDPOS 0x0008
239#define B43_SHM_SH_RXPADOFF 0x0034 /* RX Padding data offset (PIO only) */
240#define B43_SHM_SH_FWCAPA 0x0042 /* Firmware capabilities (Opensource firmware only) */
241#define B43_SHM_SH_PHYVER 0x0050 /* PHY version */
242#define B43_SHM_SH_PHYTYPE 0x0052 /* PHY type */
243#define B43_SHM_SH_ANTSWAP 0x005C /* Antenna swap threshold */
244#define B43_SHM_SH_HOSTFLO 0x005E /* Hostflags for ucode options (low) */
245#define B43_SHM_SH_HOSTFMI 0x0060 /* Hostflags for ucode options (middle) */
246#define B43_SHM_SH_HOSTFHI 0x0062 /* Hostflags for ucode options (high) */
247#define B43_SHM_SH_RFATT 0x0064 /* Current radio attenuation value */
248#define B43_SHM_SH_RADAR 0x0066 /* Radar register */
249#define B43_SHM_SH_PHYTXNOI 0x006E /* PHY noise directly after TX (lower 8bit only) */
250#define B43_SHM_SH_RFRXSP1 0x0072 /* RF RX SP Register 1 */
251#define B43_SHM_SH_CHAN 0x00A0 /* Current channel (low 8bit only) */
252#define B43_SHM_SH_CHAN_5GHZ 0x0100 /* Bit set, if 5 Ghz channel */
253#define B43_SHM_SH_CHAN_40MHZ 0x0200 /* Bit set, if 40 Mhz channel width */
254#define B43_SHM_SH_BCMCFIFOID 0x0108 /* Last posted cookie to the bcast/mcast FIFO */
255/* TSSI information */
256#define B43_SHM_SH_TSSI_CCK 0x0058 /* TSSI for last 4 CCK frames (32bit) */
257#define B43_SHM_SH_TSSI_OFDM_A 0x0068 /* TSSI for last 4 OFDM frames (32bit) */
258#define B43_SHM_SH_TSSI_OFDM_G 0x0070 /* TSSI for last 4 OFDM frames (32bit) */
259#define B43_TSSI_MAX 0x7F /* Max value for one TSSI value */
260/* SHM_SHARED TX FIFO variables */
261#define B43_SHM_SH_SIZE01 0x0098 /* TX FIFO size for FIFO 0 (low) and 1 (high) */
262#define B43_SHM_SH_SIZE23 0x009A /* TX FIFO size for FIFO 2 and 3 */
263#define B43_SHM_SH_SIZE45 0x009C /* TX FIFO size for FIFO 4 and 5 */
264#define B43_SHM_SH_SIZE67 0x009E /* TX FIFO size for FIFO 6 and 7 */
265/* SHM_SHARED background noise */
266#define B43_SHM_SH_JSSI0 0x0088 /* Measure JSSI 0 */
267#define B43_SHM_SH_JSSI1 0x008A /* Measure JSSI 1 */
268#define B43_SHM_SH_JSSIAUX 0x008C /* Measure JSSI AUX */
269/* SHM_SHARED crypto engine */
270#define B43_SHM_SH_DEFAULTIV 0x003C /* Default IV location */
271#define B43_SHM_SH_NRRXTRANS 0x003E /* # of soft RX transmitter addresses (max 8) */
272#define B43_SHM_SH_KTP 0x0056 /* Key table pointer */
273#define B43_SHM_SH_TKIPTSCTTAK 0x0318
274#define B43_SHM_SH_KEYIDXBLOCK 0x05D4 /* Key index/algorithm block (v4 firmware) */
275#define B43_SHM_SH_PSM 0x05F4 /* PSM transmitter address match block (rev < 5) */
276/* SHM_SHARED WME variables */
277#define B43_SHM_SH_EDCFSTAT 0x000E /* EDCF status */
278#define B43_SHM_SH_TXFCUR 0x0030 /* TXF current index */
279#define B43_SHM_SH_EDCFQ 0x0240 /* EDCF Q info */
280/* SHM_SHARED powersave mode related */
281#define B43_SHM_SH_SLOTT 0x0010 /* Slot time */
282#define B43_SHM_SH_DTIMPER 0x0012 /* DTIM period */
283#define B43_SHM_SH_NOSLPZNATDTIM 0x004C /* NOSLPZNAT DTIM */
284/* SHM_SHARED beacon/AP variables */
285#define B43_SHM_SH_BTL0 0x0018 /* Beacon template length 0 */
286#define B43_SHM_SH_BTL1 0x001A /* Beacon template length 1 */
287#define B43_SHM_SH_BTSFOFF 0x001C /* Beacon TSF offset */
288#define B43_SHM_SH_TIMBPOS 0x001E /* TIM B position in beacon */
289#define B43_SHM_SH_DTIMP 0x0012 /* DTIP period */
290#define B43_SHM_SH_MCASTCOOKIE 0x00A8 /* Last bcast/mcast frame ID */
291#define B43_SHM_SH_SFFBLIM 0x0044 /* Short frame fallback retry limit */
292#define B43_SHM_SH_LFFBLIM 0x0046 /* Long frame fallback retry limit */
293#define B43_SHM_SH_BEACPHYCTL 0x0054 /* Beacon PHY TX control word (see PHY TX control) */
294#define B43_SHM_SH_EXTNPHYCTL 0x00B0 /* Extended bytes for beacon PHY control (N) */
295/* SHM_SHARED ACK/CTS control */
296#define B43_SHM_SH_ACKCTSPHYCTL 0x0022 /* ACK/CTS PHY control word (see PHY TX control) */
297/* SHM_SHARED probe response variables */
298#define B43_SHM_SH_PRSSID 0x0160 /* Probe Response SSID */
299#define B43_SHM_SH_PRSSIDLEN 0x0048 /* Probe Response SSID length */
300#define B43_SHM_SH_PRTLEN 0x004A /* Probe Response template length */
301#define B43_SHM_SH_PRMAXTIME 0x0074 /* Probe Response max time */
302#define B43_SHM_SH_PRPHYCTL 0x0188 /* Probe Response PHY TX control word */
303/* SHM_SHARED rate tables */
304#define B43_SHM_SH_OFDMDIRECT 0x01C0 /* Pointer to OFDM direct map */
305#define B43_SHM_SH_OFDMBASIC 0x01E0 /* Pointer to OFDM basic rate map */
306#define B43_SHM_SH_CCKDIRECT 0x0200 /* Pointer to CCK direct map */
307#define B43_SHM_SH_CCKBASIC 0x0220 /* Pointer to CCK basic rate map */
308/* SHM_SHARED microcode soft registers */
309#define B43_SHM_SH_UCODEREV 0x0000 /* Microcode revision */
310#define B43_SHM_SH_UCODEPATCH 0x0002 /* Microcode patchlevel */
311#define B43_SHM_SH_UCODEDATE 0x0004 /* Microcode date */
312#define B43_SHM_SH_UCODETIME 0x0006 /* Microcode time */
313#define B43_SHM_SH_UCODESTAT 0x0040 /* Microcode debug status code */
314#define B43_SHM_SH_UCODESTAT_INVALID 0
315#define B43_SHM_SH_UCODESTAT_INIT 1
316#define B43_SHM_SH_UCODESTAT_ACTIVE 2
317#define B43_SHM_SH_UCODESTAT_SUSP 3 /* suspended */
318#define B43_SHM_SH_UCODESTAT_SLEEP 4 /* asleep (PS) */
319#define B43_SHM_SH_MAXBFRAMES 0x0080 /* Maximum number of frames in a burst */
320#define B43_SHM_SH_SPUWKUP 0x0094 /* pre-wakeup for synth PU in us */
321#define B43_SHM_SH_PRETBTT 0x0096 /* pre-TBTT in us */
322/* SHM_SHARED tx iq workarounds */
323#define B43_SHM_SH_NPHY_TXIQW0 0x0700
324#define B43_SHM_SH_NPHY_TXIQW1 0x0702
325#define B43_SHM_SH_NPHY_TXIQW2 0x0704
326#define B43_SHM_SH_NPHY_TXIQW3 0x0706
327/* SHM_SHARED tx pwr ctrl */
328#define B43_SHM_SH_NPHY_TXPWR_INDX0 0x0708
329#define B43_SHM_SH_NPHY_TXPWR_INDX1 0x070E
330
331/* SHM_SCRATCH offsets */
332#define B43_SHM_SC_MINCONT 0x0003 /* Minimum contention window */
333#define B43_SHM_SC_MAXCONT 0x0004 /* Maximum contention window */
334#define B43_SHM_SC_CURCONT 0x0005 /* Current contention window */
335#define B43_SHM_SC_SRLIMIT 0x0006 /* Short retry count limit */
336#define B43_SHM_SC_LRLIMIT 0x0007 /* Long retry count limit */
337#define B43_SHM_SC_DTIMC 0x0008 /* Current DTIM count */
338#define B43_SHM_SC_BTL0LEN 0x0015 /* Beacon 0 template length */
339#define B43_SHM_SC_BTL1LEN 0x0016 /* Beacon 1 template length */
340#define B43_SHM_SC_SCFB 0x0017 /* Short frame transmit count threshold for rate fallback */
341#define B43_SHM_SC_LCFB 0x0018 /* Long frame transmit count threshold for rate fallback */
342
343/* Hardware Radio Enable masks */
344#define B43_MMIO_RADIO_HWENABLED_HI_MASK (1 << 16)
345#define B43_MMIO_RADIO_HWENABLED_LO_MASK (1 << 4)
346
347/* HostFlags. See b43_hf_read/write() */
348#define B43_HF_ANTDIVHELP 0x000000000001ULL /* ucode antenna div helper */
349#define B43_HF_SYMW 0x000000000002ULL /* G-PHY SYM workaround */
350#define B43_HF_RXPULLW 0x000000000004ULL /* RX pullup workaround */
351#define B43_HF_CCKBOOST 0x000000000008ULL /* 4dB CCK power boost (exclusive with OFDM boost) */
352#define B43_HF_BTCOEX 0x000000000010ULL /* Bluetooth coexistance */
353#define B43_HF_GDCW 0x000000000020ULL /* G-PHY DC canceller filter bw workaround */
354#define B43_HF_OFDMPABOOST 0x000000000040ULL /* Enable PA gain boost for OFDM */
355#define B43_HF_ACPR 0x000000000080ULL /* Disable for Japan, channel 14 */
356#define B43_HF_EDCF 0x000000000100ULL /* on if WME and MAC suspended */
357#define B43_HF_TSSIRPSMW 0x000000000200ULL /* TSSI reset PSM ucode workaround */
358#define B43_HF_20IN40IQW 0x000000000200ULL /* 20 in 40 MHz I/Q workaround (rev >= 13 only) */
359#define B43_HF_DSCRQ 0x000000000400ULL /* Disable slow clock request in ucode */
360#define B43_HF_ACIW 0x000000000800ULL /* ACI workaround: shift bits by 2 on PHY CRS */
361#define B43_HF_2060W 0x000000001000ULL /* 2060 radio workaround */
362#define B43_HF_RADARW 0x000000002000ULL /* Radar workaround */
363#define B43_HF_USEDEFKEYS 0x000000004000ULL /* Enable use of default keys */
364#define B43_HF_AFTERBURNER 0x000000008000ULL /* Afterburner enabled */
365#define B43_HF_BT4PRIOCOEX 0x000000010000ULL /* Bluetooth 4-priority coexistance */
366#define B43_HF_FWKUP 0x000000020000ULL /* Fast wake-up ucode */
367#define B43_HF_VCORECALC 0x000000040000ULL /* Force VCO recalculation when powering up synthpu */
368#define B43_HF_PCISCW 0x000000080000ULL /* PCI slow clock workaround */
369#define B43_HF_4318TSSI 0x000000200000ULL /* 4318 TSSI */
370#define B43_HF_FBCMCFIFO 0x000000400000ULL /* Flush bcast/mcast FIFO immediately */
371#define B43_HF_HWPCTL 0x000000800000ULL /* Enable hardwarre power control */
372#define B43_HF_BTCOEXALT 0x000001000000ULL /* Bluetooth coexistance in alternate pins */
373#define B43_HF_TXBTCHECK 0x000002000000ULL /* Bluetooth check during transmission */
374#define B43_HF_SKCFPUP 0x000004000000ULL /* Skip CFP update */
375#define B43_HF_N40W 0x000008000000ULL /* N PHY 40 MHz workaround (rev >= 13 only) */
376#define B43_HF_ANTSEL 0x000020000000ULL /* Antenna selection (for testing antenna div.) */
377#define B43_HF_BT3COEXT 0x000020000000ULL /* Bluetooth 3-wire coexistence (rev >= 13 only) */
378#define B43_HF_BTCANT 0x000040000000ULL /* Bluetooth coexistence (antenna mode) (rev >= 13 only) */
379#define B43_HF_ANTSELEN 0x000100000000ULL /* Antenna selection enabled (rev >= 13 only) */
380#define B43_HF_ANTSELMODE 0x000200000000ULL /* Antenna selection mode (rev >= 13 only) */
381#define B43_HF_MLADVW 0x001000000000ULL /* N PHY ML ADV workaround (rev >= 13 only) */
382#define B43_HF_PR45960W 0x080000000000ULL /* PR 45960 workaround (rev >= 13 only) */
383
384/* Firmware capabilities field in SHM (Opensource firmware only) */
385#define B43_FWCAPA_HWCRYPTO 0x0001
386#define B43_FWCAPA_QOS 0x0002
387
388/* MacFilter offsets. */
389#define B43_MACFILTER_SELF 0x0000
390#define B43_MACFILTER_BSSID 0x0003
391
392/* PowerControl */
393#define B43_PCTL_IN 0xB0
394#define B43_PCTL_OUT 0xB4
395#define B43_PCTL_OUTENABLE 0xB8
396#define B43_PCTL_XTAL_POWERUP 0x40
397#define B43_PCTL_PLL_POWERDOWN 0x80
398
399/* PowerControl Clock Modes */
400#define B43_PCTL_CLK_FAST 0x00
401#define B43_PCTL_CLK_SLOW 0x01
402#define B43_PCTL_CLK_DYNAMIC 0x02
403
404#define B43_PCTL_FORCE_SLOW 0x0800
405#define B43_PCTL_FORCE_PLL 0x1000
406#define B43_PCTL_DYN_XTAL 0x2000
407
408/* PHYVersioning */
409#define B43_PHYTYPE_A 0x00
410#define B43_PHYTYPE_B 0x01
411#define B43_PHYTYPE_G 0x02
412#define B43_PHYTYPE_N 0x04
413#define B43_PHYTYPE_LP 0x05
414#define B43_PHYTYPE_SSLPN 0x06
415#define B43_PHYTYPE_HT 0x07
416#define B43_PHYTYPE_LCN 0x08
417#define B43_PHYTYPE_LCNXN 0x09
418
419/* PHYRegisters */
420#define B43_PHY_ILT_A_CTRL 0x0072
421#define B43_PHY_ILT_A_DATA1 0x0073
422#define B43_PHY_ILT_A_DATA2 0x0074
423#define B43_PHY_G_LO_CONTROL 0x0810
424#define B43_PHY_ILT_G_CTRL 0x0472
425#define B43_PHY_ILT_G_DATA1 0x0473
426#define B43_PHY_ILT_G_DATA2 0x0474
427#define B43_PHY_A_PCTL 0x007B
428#define B43_PHY_G_PCTL 0x0029
429#define B43_PHY_A_CRS 0x0029
430#define B43_PHY_RADIO_BITFIELD 0x0401
431#define B43_PHY_G_CRS 0x0429
432#define B43_PHY_NRSSILT_CTRL 0x0803
433#define B43_PHY_NRSSILT_DATA 0x0804
434
435/* RadioRegisters */
436#define B43_RADIOCTL_ID 0x01
437
438/* MAC Control bitfield */
439#define B43_MACCTL_ENABLED 0x00000001 /* MAC Enabled */
440#define B43_MACCTL_PSM_RUN 0x00000002 /* Run Microcode */
441#define B43_MACCTL_PSM_JMP0 0x00000004 /* Microcode jump to 0 */
442#define B43_MACCTL_SHM_ENABLED 0x00000100 /* SHM Enabled */
443#define B43_MACCTL_SHM_UPPER 0x00000200 /* SHM Upper */
444#define B43_MACCTL_IHR_ENABLED 0x00000400 /* IHR Region Enabled */
445#define B43_MACCTL_PSM_DBG 0x00002000 /* Microcode debugging enabled */
446#define B43_MACCTL_GPOUTSMSK 0x0000C000 /* GPOUT Select Mask */
447#define B43_MACCTL_BE 0x00010000 /* Big Endian mode */
448#define B43_MACCTL_INFRA 0x00020000 /* Infrastructure mode */
449#define B43_MACCTL_AP 0x00040000 /* AccessPoint mode */
450#define B43_MACCTL_RADIOLOCK 0x00080000 /* Radio lock */
451#define B43_MACCTL_BEACPROMISC 0x00100000 /* Beacon Promiscuous */
452#define B43_MACCTL_KEEP_BADPLCP 0x00200000 /* Keep frames with bad PLCP */
453#define B43_MACCTL_KEEP_CTL 0x00400000 /* Keep control frames */
454#define B43_MACCTL_KEEP_BAD 0x00800000 /* Keep bad frames (FCS) */
455#define B43_MACCTL_PROMISC 0x01000000 /* Promiscuous mode */
456#define B43_MACCTL_HWPS 0x02000000 /* Hardware Power Saving */
457#define B43_MACCTL_AWAKE 0x04000000 /* Device is awake */
458#define B43_MACCTL_CLOSEDNET 0x08000000 /* Closed net (no SSID bcast) */
459#define B43_MACCTL_TBTTHOLD 0x10000000 /* TBTT Hold */
460#define B43_MACCTL_DISCTXSTAT 0x20000000 /* Discard TX status */
461#define B43_MACCTL_DISCPMQ 0x40000000 /* Discard Power Management Queue */
462#define B43_MACCTL_GMODE 0x80000000 /* G Mode */
463
464/* MAC Command bitfield */
465#define B43_MACCMD_BEACON0_VALID 0x00000001 /* Beacon 0 in template RAM is busy/valid */
466#define B43_MACCMD_BEACON1_VALID 0x00000002 /* Beacon 1 in template RAM is busy/valid */
467#define B43_MACCMD_DFQ_VALID 0x00000004 /* Directed frame queue valid (IBSS PS mode, ATIM) */
468#define B43_MACCMD_CCA 0x00000008 /* Clear channel assessment */
469#define B43_MACCMD_BGNOISE 0x00000010 /* Background noise */
470
471/* BCMA 802.11 core specific IO Control (BCMA_IOCTL) flags */
472#define B43_BCMA_IOCTL_PHY_CLKEN 0x00000004 /* PHY Clock Enable */
473#define B43_BCMA_IOCTL_PHY_RESET 0x00000008 /* PHY Reset */
474#define B43_BCMA_IOCTL_MACPHYCLKEN 0x00000010 /* MAC PHY Clock Control Enable */
475#define B43_BCMA_IOCTL_PLLREFSEL 0x00000020 /* PLL Frequency Reference Select */
476#define B43_BCMA_IOCTL_PHY_BW 0x000000C0 /* PHY band width and clock speed mask (N-PHY+ only?) */
477#define B43_BCMA_IOCTL_PHY_BW_10MHZ 0x00000000 /* 10 MHz bandwidth, 40 MHz PHY */
478#define B43_BCMA_IOCTL_PHY_BW_20MHZ 0x00000040 /* 20 MHz bandwidth, 80 MHz PHY */
479#define B43_BCMA_IOCTL_PHY_BW_40MHZ 0x00000080 /* 40 MHz bandwidth, 160 MHz PHY */
480#define B43_BCMA_IOCTL_GMODE 0x00002000 /* G Mode Enable */
481
482/* BCMA 802.11 core specific IO status (BCMA_IOST) flags */
483#define B43_BCMA_IOST_2G_PHY 0x00000001 /* 2.4G capable phy */
484#define B43_BCMA_IOST_5G_PHY 0x00000002 /* 5G capable phy */
485#define B43_BCMA_IOST_FASTCLKA 0x00000004 /* Fast Clock Available */
486#define B43_BCMA_IOST_DUALB_PHY 0x00000008 /* Dualband phy */
487
488/* 802.11 core specific TM State Low (SSB_TMSLOW) flags */
489#define B43_TMSLOW_GMODE 0x20000000 /* G Mode Enable */
490#define B43_TMSLOW_PHY_BANDWIDTH 0x00C00000 /* PHY band width and clock speed mask (N-PHY only) */
491#define B43_TMSLOW_PHY_BANDWIDTH_10MHZ 0x00000000 /* 10 MHz bandwidth, 40 MHz PHY */
492#define B43_TMSLOW_PHY_BANDWIDTH_20MHZ 0x00400000 /* 20 MHz bandwidth, 80 MHz PHY */
493#define B43_TMSLOW_PHY_BANDWIDTH_40MHZ 0x00800000 /* 40 MHz bandwidth, 160 MHz PHY */
494#define B43_TMSLOW_PLLREFSEL 0x00200000 /* PLL Frequency Reference Select (rev >= 5) */
495#define B43_TMSLOW_MACPHYCLKEN 0x00100000 /* MAC PHY Clock Control Enable (rev >= 5) */
496#define B43_TMSLOW_PHYRESET 0x00080000 /* PHY Reset */
497#define B43_TMSLOW_PHYCLKEN 0x00040000 /* PHY Clock Enable */
498
499/* 802.11 core specific TM State High (SSB_TMSHIGH) flags */
500#define B43_TMSHIGH_DUALBAND_PHY 0x00080000 /* Dualband PHY available */
501#define B43_TMSHIGH_FCLOCK 0x00040000 /* Fast Clock Available (rev >= 5) */
502#define B43_TMSHIGH_HAVE_5GHZ_PHY 0x00020000 /* 5 GHz PHY available (rev >= 5) */
503#define B43_TMSHIGH_HAVE_2GHZ_PHY 0x00010000 /* 2.4 GHz PHY available (rev >= 5) */
504
505/* Generic-Interrupt reasons. */
506#define B43_IRQ_MAC_SUSPENDED 0x00000001
507#define B43_IRQ_BEACON 0x00000002
508#define B43_IRQ_TBTT_INDI 0x00000004
509#define B43_IRQ_BEACON_TX_OK 0x00000008
510#define B43_IRQ_BEACON_CANCEL 0x00000010
511#define B43_IRQ_ATIM_END 0x00000020
512#define B43_IRQ_PMQ 0x00000040
513#define B43_IRQ_PIO_WORKAROUND 0x00000100
514#define B43_IRQ_MAC_TXERR 0x00000200
515#define B43_IRQ_PHY_TXERR 0x00000800
516#define B43_IRQ_PMEVENT 0x00001000
517#define B43_IRQ_TIMER0 0x00002000
518#define B43_IRQ_TIMER1 0x00004000
519#define B43_IRQ_DMA 0x00008000
520#define B43_IRQ_TXFIFO_FLUSH_OK 0x00010000
521#define B43_IRQ_CCA_MEASURE_OK 0x00020000
522#define B43_IRQ_NOISESAMPLE_OK 0x00040000
523#define B43_IRQ_UCODE_DEBUG 0x08000000
524#define B43_IRQ_RFKILL 0x10000000
525#define B43_IRQ_TX_OK 0x20000000
526#define B43_IRQ_PHY_G_CHANGED 0x40000000
527#define B43_IRQ_TIMEOUT 0x80000000
528
529#define B43_IRQ_ALL 0xFFFFFFFF
530#define B43_IRQ_MASKTEMPLATE (B43_IRQ_TBTT_INDI | \
531 B43_IRQ_ATIM_END | \
532 B43_IRQ_PMQ | \
533 B43_IRQ_MAC_TXERR | \
534 B43_IRQ_PHY_TXERR | \
535 B43_IRQ_DMA | \
536 B43_IRQ_TXFIFO_FLUSH_OK | \
537 B43_IRQ_NOISESAMPLE_OK | \
538 B43_IRQ_UCODE_DEBUG | \
539 B43_IRQ_RFKILL | \
540 B43_IRQ_TX_OK)
541
542/* The firmware register to fetch the debug-IRQ reason from. */
543#define B43_DEBUGIRQ_REASON_REG 63
544/* Debug-IRQ reasons. */
545#define B43_DEBUGIRQ_PANIC 0 /* The firmware panic'ed */
546#define B43_DEBUGIRQ_DUMP_SHM 1 /* Dump shared SHM */
547#define B43_DEBUGIRQ_DUMP_REGS 2 /* Dump the microcode registers */
548#define B43_DEBUGIRQ_MARKER 3 /* A "marker" was thrown by the firmware. */
549#define B43_DEBUGIRQ_ACK 0xFFFF /* The host writes that to ACK the IRQ */
550
551/* The firmware register that contains the "marker" line. */
552#define B43_MARKER_ID_REG 2
553#define B43_MARKER_LINE_REG 3
554
555/* The firmware register to fetch the panic reason from. */
556#define B43_FWPANIC_REASON_REG 3
557/* Firmware panic reason codes */
558#define B43_FWPANIC_DIE 0 /* Firmware died. Don't auto-restart it. */
559#define B43_FWPANIC_RESTART 1 /* Firmware died. Schedule a controller reset. */
560
561/* The firmware register that contains the watchdog counter. */
562#define B43_WATCHDOG_REG 1
563
564/* Device specific rate values.
565 * The actual values defined here are (rate_in_mbps * 2).
566 * Some code depends on this. Don't change it. */
567#define B43_CCK_RATE_1MB 0x02
568#define B43_CCK_RATE_2MB 0x04
569#define B43_CCK_RATE_5MB 0x0B
570#define B43_CCK_RATE_11MB 0x16
571#define B43_OFDM_RATE_6MB 0x0C
572#define B43_OFDM_RATE_9MB 0x12
573#define B43_OFDM_RATE_12MB 0x18
574#define B43_OFDM_RATE_18MB 0x24
575#define B43_OFDM_RATE_24MB 0x30
576#define B43_OFDM_RATE_36MB 0x48
577#define B43_OFDM_RATE_48MB 0x60
578#define B43_OFDM_RATE_54MB 0x6C
579/* Convert a b43 rate value to a rate in 100kbps */
580#define B43_RATE_TO_BASE100KBPS(rate) (((rate) * 10) / 2)
581
582#define B43_DEFAULT_SHORT_RETRY_LIMIT 7
583#define B43_DEFAULT_LONG_RETRY_LIMIT 4
584
585#define B43_PHY_TX_BADNESS_LIMIT 1000
586
587/* Max size of a security key */
588#define B43_SEC_KEYSIZE 16
589/* Max number of group keys */
590#define B43_NR_GROUP_KEYS 4
591/* Max number of pairwise keys */
592#define B43_NR_PAIRWISE_KEYS 50
593/* Security algorithms. */
594enum {
595 B43_SEC_ALGO_NONE = 0, /* unencrypted, as of TX header. */
596 B43_SEC_ALGO_WEP40,
597 B43_SEC_ALGO_TKIP,
598 B43_SEC_ALGO_AES,
599 B43_SEC_ALGO_WEP104,
600 B43_SEC_ALGO_AES_LEGACY,
601};
602
603struct b43_dmaring;
604
605/* The firmware file header */
606#define B43_FW_TYPE_UCODE 'u'
607#define B43_FW_TYPE_PCM 'p'
608#define B43_FW_TYPE_IV 'i'
609struct b43_fw_header {
610 /* File type */
611 u8 type;
612 /* File format version */
613 u8 ver;
614 u8 __padding[2];
615 /* Size of the data. For ucode and PCM this is in bytes.
616 * For IV this is number-of-ivs. */
617 __be32 size;
618} __packed;
619
620/* Initial Value file format */
621#define B43_IV_OFFSET_MASK 0x7FFF
622#define B43_IV_32BIT 0x8000
623struct b43_iv {
624 __be16 offset_size;
625 union {
626 __be16 d16;
627 __be32 d32;
628 } data __packed;
629} __packed;
630
631
632/* Data structures for DMA transmission, per 80211 core. */
633struct b43_dma {
634 struct b43_dmaring *tx_ring_AC_BK; /* Background */
635 struct b43_dmaring *tx_ring_AC_BE; /* Best Effort */
636 struct b43_dmaring *tx_ring_AC_VI; /* Video */
637 struct b43_dmaring *tx_ring_AC_VO; /* Voice */
638 struct b43_dmaring *tx_ring_mcast; /* Multicast */
639
640 struct b43_dmaring *rx_ring;
641
642 u32 translation; /* Routing bits */
643 bool translation_in_low; /* Should translation bit go into low addr? */
644 bool parity; /* Check for parity */
645};
646
647struct b43_pio_txqueue;
648struct b43_pio_rxqueue;
649
650/* Data structures for PIO transmission, per 80211 core. */
651struct b43_pio {
652 struct b43_pio_txqueue *tx_queue_AC_BK; /* Background */
653 struct b43_pio_txqueue *tx_queue_AC_BE; /* Best Effort */
654 struct b43_pio_txqueue *tx_queue_AC_VI; /* Video */
655 struct b43_pio_txqueue *tx_queue_AC_VO; /* Voice */
656 struct b43_pio_txqueue *tx_queue_mcast; /* Multicast */
657
658 struct b43_pio_rxqueue *rx_queue;
659};
660
661/* Context information for a noise calculation (Link Quality). */
662struct b43_noise_calculation {
663 bool calculation_running;
664 u8 nr_samples;
665 s8 samples[8][4];
666};
667
668struct b43_stats {
669 u8 link_noise;
670};
671
672struct b43_key {
673 /* If keyconf is NULL, this key is disabled.
674 * keyconf is a cookie. Don't derefenrence it outside of the set_key
675 * path, because b43 doesn't own it. */
676 struct ieee80211_key_conf *keyconf;
677 u8 algorithm;
678};
679
680/* SHM offsets to the QOS data structures for the 4 different queues. */
681#define B43_QOS_QUEUE_NUM 4
682#define B43_QOS_PARAMS(queue) (B43_SHM_SH_EDCFQ + \
683 (B43_NR_QOSPARAMS * sizeof(u16) * (queue)))
684#define B43_QOS_BACKGROUND B43_QOS_PARAMS(0)
685#define B43_QOS_BESTEFFORT B43_QOS_PARAMS(1)
686#define B43_QOS_VIDEO B43_QOS_PARAMS(2)
687#define B43_QOS_VOICE B43_QOS_PARAMS(3)
688
689/* QOS parameter hardware data structure offsets. */
690#define B43_NR_QOSPARAMS 16
691enum {
692 B43_QOSPARAM_TXOP = 0,
693 B43_QOSPARAM_CWMIN,
694 B43_QOSPARAM_CWMAX,
695 B43_QOSPARAM_CWCUR,
696 B43_QOSPARAM_AIFS,
697 B43_QOSPARAM_BSLOTS,
698 B43_QOSPARAM_REGGAP,
699 B43_QOSPARAM_STATUS,
700};
701
702/* QOS parameters for a queue. */
703struct b43_qos_params {
704 /* The QOS parameters */
705 struct ieee80211_tx_queue_params p;
706};
707
708struct b43_wl;
709
710/* The type of the firmware file. */
711enum b43_firmware_file_type {
712 B43_FWTYPE_PROPRIETARY,
713 B43_FWTYPE_OPENSOURCE,
714 B43_NR_FWTYPES,
715};
716
717/* Context data for fetching firmware. */
718struct b43_request_fw_context {
719 /* The device we are requesting the fw for. */
720 struct b43_wldev *dev;
721 /* The type of firmware to request. */
722 enum b43_firmware_file_type req_type;
723 /* Error messages for each firmware type. */
724 char errors[B43_NR_FWTYPES][128];
725 /* Temporary buffer for storing the firmware name. */
726 char fwname[64];
727 /* A fatal error occurred while requesting. Firmware request
728 * can not continue, as any other request will also fail. */
729 int fatal_failure;
730};
731
732/* In-memory representation of a cached microcode file. */
733struct b43_firmware_file {
734 const char *filename;
735 const struct firmware *data;
736 /* Type of the firmware file name. Note that this does only indicate
737 * the type by the firmware name. NOT the file contents.
738 * If you want to check for proprietary vs opensource, use (struct b43_firmware)->opensource
739 * instead! The (struct b43_firmware)->opensource flag is derived from the actual firmware
740 * binary code, not just the filename.
741 */
742 enum b43_firmware_file_type type;
743};
744
745enum b43_firmware_hdr_format {
746 B43_FW_HDR_598,
747 B43_FW_HDR_410,
748 B43_FW_HDR_351,
749};
750
751/* Pointers to the firmware data and meta information about it. */
752struct b43_firmware {
753 /* Microcode */
754 struct b43_firmware_file ucode;
755 /* PCM code */
756 struct b43_firmware_file pcm;
757 /* Initial MMIO values for the firmware */
758 struct b43_firmware_file initvals;
759 /* Initial MMIO values for the firmware, band-specific */
760 struct b43_firmware_file initvals_band;
761
762 /* Firmware revision */
763 u16 rev;
764 /* Firmware patchlevel */
765 u16 patch;
766
767 /* Format of header used by firmware */
768 enum b43_firmware_hdr_format hdr_format;
769
770 /* Set to true, if we are using an opensource firmware.
771 * Use this to check for proprietary vs opensource. */
772 bool opensource;
773 /* Set to true, if the core needs a PCM firmware, but
774 * we failed to load one. This is always false for
775 * core rev > 10, as these don't need PCM firmware. */
776 bool pcm_request_failed;
777};
778
779/* Device (802.11 core) initialization status. */
780enum {
781 B43_STAT_UNINIT = 0, /* Uninitialized. */
782 B43_STAT_INITIALIZED = 1, /* Initialized, but not started, yet. */
783 B43_STAT_STARTED = 2, /* Up and running. */
784};
785#define b43_status(wldev) atomic_read(&(wldev)->__init_status)
786#define b43_set_status(wldev, stat) do { \
787 atomic_set(&(wldev)->__init_status, (stat)); \
788 smp_wmb(); \
789 } while (0)
790
791/* Data structure for one wireless device (802.11 core) */
792struct b43_wldev {
793 struct b43_bus_dev *dev;
794 struct b43_wl *wl;
795
796 /* The device initialization status.
797 * Use b43_status() to query. */
798 atomic_t __init_status;
799
800 bool bad_frames_preempt; /* Use "Bad Frames Preemption" (default off) */
801 bool dfq_valid; /* Directed frame queue valid (IBSS PS mode, ATIM) */
802 bool radio_hw_enable; /* saved state of radio hardware enabled state */
803 bool qos_enabled; /* TRUE, if QoS is used. */
804 bool hwcrypto_enabled; /* TRUE, if HW crypto acceleration is enabled. */
805 bool use_pio; /* TRUE if next init should use PIO */
806
807 /* PHY/Radio device. */
808 struct b43_phy phy;
809
810 union {
811 /* DMA engines. */
812 struct b43_dma dma;
813 /* PIO engines. */
814 struct b43_pio pio;
815 };
816 /* Use b43_using_pio_transfers() to check whether we are using
817 * DMA or PIO data transfers. */
818 bool __using_pio_transfers;
819
820 /* Various statistics about the physical device. */
821 struct b43_stats stats;
822
823 /* Reason code of the last interrupt. */
824 u32 irq_reason;
825 u32 dma_reason[6];
826 /* The currently active generic-interrupt mask. */
827 u32 irq_mask;
828
829 /* Link Quality calculation context. */
830 struct b43_noise_calculation noisecalc;
831 /* if > 0 MAC is suspended. if == 0 MAC is enabled. */
832 int mac_suspended;
833
834 /* Periodic tasks */
835 struct delayed_work periodic_work;
836 unsigned int periodic_state;
837
838 struct work_struct restart_work;
839
840 /* encryption/decryption */
841 u16 ktp; /* Key table pointer */
842 struct b43_key key[B43_NR_GROUP_KEYS * 2 + B43_NR_PAIRWISE_KEYS];
843
844 /* Firmware data */
845 struct b43_firmware fw;
846
847 /* Devicelist in struct b43_wl (all 802.11 cores) */
848 struct list_head list;
849
850 /* Debugging stuff follows. */
851#ifdef CONFIG_B43_DEBUG
852 struct b43_dfsentry *dfsentry;
853 unsigned int irq_count;
854 unsigned int irq_bit_count[32];
855 unsigned int tx_count;
856 unsigned int rx_count;
857#endif
858};
859
860/* Data structure for the WLAN parts (802.11 cores) of the b43 chip. */
861struct b43_wl {
862 /* Pointer to the active wireless device on this chip */
863 struct b43_wldev *current_dev;
864 /* Pointer to the ieee80211 hardware data structure */
865 struct ieee80211_hw *hw;
866
867 /* Global driver mutex. Every operation must run with this mutex locked. */
868 struct mutex mutex;
869 /* Hard-IRQ spinlock. This lock protects things used in the hard-IRQ
870 * handler, only. This basically is just the IRQ mask register. */
871 spinlock_t hardirq_lock;
872
873 /* Set this if we call ieee80211_register_hw() and check if we call
874 * ieee80211_unregister_hw(). */
875 bool hw_registred;
876
877 /* We can only have one operating interface (802.11 core)
878 * at a time. General information about this interface follows.
879 */
880
881 struct ieee80211_vif *vif;
882 /* The MAC address of the operating interface. */
883 u8 mac_addr[ETH_ALEN];
884 /* Current BSSID */
885 u8 bssid[ETH_ALEN];
886 /* Interface type. (NL80211_IFTYPE_XXX) */
887 int if_type;
888 /* Is the card operating in AP, STA or IBSS mode? */
889 bool operating;
890 /* filter flags */
891 unsigned int filter_flags;
892 /* Stats about the wireless interface */
893 struct ieee80211_low_level_stats ieee_stats;
894
895#ifdef CONFIG_B43_HWRNG
896 struct hwrng rng;
897 bool rng_initialized;
898 char rng_name[30 + 1];
899#endif /* CONFIG_B43_HWRNG */
900
901 /* List of all wireless devices on this chip */
902 struct list_head devlist;
903 u8 nr_devs;
904
905 bool radiotap_enabled;
906 bool radio_enabled;
907
908 /* The beacon we are currently using (AP or IBSS mode). */
909 struct sk_buff *current_beacon;
910 bool beacon0_uploaded;
911 bool beacon1_uploaded;
912 bool beacon_templates_virgin; /* Never wrote the templates? */
913 struct work_struct beacon_update_trigger;
914
915 /* The current QOS parameters for the 4 queues. */
916 struct b43_qos_params qos_params[B43_QOS_QUEUE_NUM];
917
918 /* Work for adjustment of the transmission power.
919 * This is scheduled when we determine that the actual TX output
920 * power doesn't match what we want. */
921 struct work_struct txpower_adjust_work;
922
923 /* Packet transmit work */
924 struct work_struct tx_work;
925
926 /* Queue of packets to be transmitted. */
927 struct sk_buff_head tx_queue[B43_QOS_QUEUE_NUM];
928
929 /* Flag that implement the queues stopping. */
930 bool tx_queue_stopped[B43_QOS_QUEUE_NUM];
931
932 /* firmware loading work */
933 struct work_struct firmware_load;
934
935 /* The device LEDs. */
936 struct b43_leds leds;
937
938 /* Kmalloc'ed scratch space for PIO TX/RX. Protected by wl->mutex. */
939 u8 pio_scratchspace[118] __attribute__((__aligned__(8)));
940 u8 pio_tailspace[4] __attribute__((__aligned__(8)));
941};
942
943static inline struct b43_wl *hw_to_b43_wl(struct ieee80211_hw *hw)
944{
945 return hw->priv;
946}
947
948static inline struct b43_wldev *dev_to_b43_wldev(struct device *dev)
949{
950 struct ssb_device *ssb_dev = dev_to_ssb_dev(dev);
951 return ssb_get_drvdata(ssb_dev);
952}
953
954/* Is the device operating in a specified mode (NL80211_IFTYPE_XXX). */
955static inline int b43_is_mode(struct b43_wl *wl, int type)
956{
957 return (wl->operating && wl->if_type == type);
958}
959
960/**
961 * b43_current_band - Returns the currently used band.
962 * Returns one of IEEE80211_BAND_2GHZ and IEEE80211_BAND_5GHZ.
963 */
964static inline enum ieee80211_band b43_current_band(struct b43_wl *wl)
965{
966 return wl->hw->conf.channel->band;
967}
968
969static inline int b43_bus_may_powerdown(struct b43_wldev *wldev)
970{
971 return wldev->dev->bus_may_powerdown(wldev->dev);
972}
973static inline int b43_bus_powerup(struct b43_wldev *wldev, bool dynamic_pctl)
974{
975 return wldev->dev->bus_powerup(wldev->dev, dynamic_pctl);
976}
977static inline int b43_device_is_enabled(struct b43_wldev *wldev)
978{
979 return wldev->dev->device_is_enabled(wldev->dev);
980}
981static inline void b43_device_enable(struct b43_wldev *wldev,
982 u32 core_specific_flags)
983{
984 wldev->dev->device_enable(wldev->dev, core_specific_flags);
985}
986static inline void b43_device_disable(struct b43_wldev *wldev,
987 u32 core_specific_flags)
988{
989 wldev->dev->device_disable(wldev->dev, core_specific_flags);
990}
991
992static inline u16 b43_read16(struct b43_wldev *dev, u16 offset)
993{
994 return dev->dev->read16(dev->dev, offset);
995}
996
997static inline void b43_write16(struct b43_wldev *dev, u16 offset, u16 value)
998{
999 dev->dev->write16(dev->dev, offset, value);
1000}
1001
1002static inline void b43_maskset16(struct b43_wldev *dev, u16 offset, u16 mask,
1003 u16 set)
1004{
1005 b43_write16(dev, offset, (b43_read16(dev, offset) & mask) | set);
1006}
1007
1008static inline u32 b43_read32(struct b43_wldev *dev, u16 offset)
1009{
1010 return dev->dev->read32(dev->dev, offset);
1011}
1012
1013static inline void b43_write32(struct b43_wldev *dev, u16 offset, u32 value)
1014{
1015 dev->dev->write32(dev->dev, offset, value);
1016}
1017
1018static inline void b43_maskset32(struct b43_wldev *dev, u16 offset, u32 mask,
1019 u32 set)
1020{
1021 b43_write32(dev, offset, (b43_read32(dev, offset) & mask) | set);
1022}
1023
1024static inline void b43_block_read(struct b43_wldev *dev, void *buffer,
1025 size_t count, u16 offset, u8 reg_width)
1026{
1027 dev->dev->block_read(dev->dev, buffer, count, offset, reg_width);
1028}
1029
1030static inline void b43_block_write(struct b43_wldev *dev, const void *buffer,
1031 size_t count, u16 offset, u8 reg_width)
1032{
1033 dev->dev->block_write(dev->dev, buffer, count, offset, reg_width);
1034}
1035
1036static inline bool b43_using_pio_transfers(struct b43_wldev *dev)
1037{
1038 return dev->__using_pio_transfers;
1039}
1040
1041/* Message printing */
1042__printf(2, 3) void b43info(struct b43_wl *wl, const char *fmt, ...);
1043__printf(2, 3) void b43err(struct b43_wl *wl, const char *fmt, ...);
1044__printf(2, 3) void b43warn(struct b43_wl *wl, const char *fmt, ...);
1045__printf(2, 3) void b43dbg(struct b43_wl *wl, const char *fmt, ...);
1046
1047
1048/* A WARN_ON variant that vanishes when b43 debugging is disabled.
1049 * This _also_ evaluates the arg with debugging disabled. */
1050#if B43_DEBUG
1051# define B43_WARN_ON(x) WARN_ON(x)
1052#else
1053static inline bool __b43_warn_on_dummy(bool x) { return x; }
1054# define B43_WARN_ON(x) __b43_warn_on_dummy(unlikely(!!(x)))
1055#endif
1056
1057/* Convert an integer to a Q5.2 value */
1058#define INT_TO_Q52(i) ((i) << 2)
1059/* Convert a Q5.2 value to an integer (precision loss!) */
1060#define Q52_TO_INT(q52) ((q52) >> 2)
1061/* Macros for printing a value in Q5.2 format */
1062#define Q52_FMT "%u.%u"
1063#define Q52_ARG(q52) Q52_TO_INT(q52), ((((q52) & 0x3) * 100) / 4)
1064
1065#endif /* B43_H_ */