1# SPDX-License-Identifier: GPL-2.0-only
 2#
 3# Cadence device configuration
 4#
 5
 6config NET_VENDOR_CADENCE
 7	bool "Cadence devices"
 8	depends on HAS_IOMEM
 9	default y
10	help
11	  If you have a network (Ethernet) card belonging to this class, say Y.
 
 
12
13	  If unsure, say Y.
14
15	  Note that the answer to this question doesn't directly affect the
16	  kernel: saying N will just cause the configurator to skip all the
17	  remaining Cadence network card questions. If you say Y, you will be
18	  asked for your specific card in the following questions.
19
20if NET_VENDOR_CADENCE
 
 
 
 
 
 
 
 
21
22config MACB
23	tristate "Cadence MACB/GEM support"
24	depends on HAS_DMA && COMMON_CLK
25	depends on PTP_1588_CLOCK_OPTIONAL
26	select PHYLINK
27	select CRC32
28	help
29	  The Cadence MACB ethernet interface is found on many Atmel AT32 and
30	  AT91 parts.  This driver also supports the Cadence GEM (Gigabit
31	  Ethernet MAC found in some ARM SoC devices).  Say Y to include
32	  support for the MACB/GEM chip.
33
34	  To compile this driver as a module, choose M here: the module
35	  will be macb.
36
37config MACB_USE_HWSTAMP
38	bool "Use IEEE 1588 hwstamp"
39	depends on MACB
40	depends on PTP_1588_CLOCK
41	default y
42	help
43	  Enable IEEE 1588 Precision Time Protocol (PTP) support for MACB.
44
45config MACB_PCI
46	tristate "Cadence PCI MACB/GEM support"
47	depends on MACB && PCI
48	help
49	  This is PCI wrapper for MACB driver.
50
51	  To compile this driver as a module, choose M here: the module
52	  will be called macb_pci.
53
54endif # NET_VENDOR_CADENCE

 
 1#
 2# Atmel device configuration
 3#
 4
 5config NET_CADENCE
 6	bool "Cadence devices"
 7	depends on HAS_IOMEM && (ARM || AVR32 || MICROBLAZE || COMPILE_TEST)
 8	default y
 9	---help---
10	  If you have a network (Ethernet) card belonging to this class, say Y.
11	  Make sure you know the name of your card. Read the Ethernet-HOWTO,
12	  available from <http://www.tldp.org/docs.html#howto>.
13
14	  If unsure, say Y.
15
16	  Note that the answer to this question doesn't directly affect the
17	  kernel: saying N will just cause the configurator to skip all
18	  the remaining Atmel network card questions. If you say Y, you will be
19	  asked for your specific card in the following questions.
20
21if NET_CADENCE
22
23config ARM_AT91_ETHER
24	tristate "AT91RM9200 Ethernet support"
25	depends on HAS_DMA && (ARCH_AT91RM9200 || COMPILE_TEST)
26	select MACB
27	---help---
28	  If you wish to compile a kernel for the AT91RM9200 and enable
29	  ethernet support, then you should always answer Y to this.
30
31config MACB
32	tristate "Cadence MACB/GEM support"
33	depends on HAS_DMA && (PLATFORM_AT32AP || ARCH_AT91 || ARCH_PICOXCELL || ARCH_ZYNQ || MICROBLAZE || COMPILE_TEST)
34	select PHYLIB
35	---help---
 
 
36	  The Cadence MACB ethernet interface is found on many Atmel AT32 and
37	  AT91 parts.  This driver also supports the Cadence GEM (Gigabit
38	  Ethernet MAC found in some ARM SoC devices).  Note: the Gigabit mode
39	  is not yet supported.  Say Y to include support for the MACB/GEM chip.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
40
41	  To compile this driver as a module, choose M here: the module
42	  will be called macb.
43
44endif # NET_CADENCE