1/dts-v1/;
  2
  3#include "dove.dtsi"
  4
  5/ {
  6	model = "Globalscale D3Plug";
  7	compatible = "globalscale,d3plug", "marvell,dove";
  8
  9	memory {
 10		device_type = "memory";
 11		reg = <0x00000000 0x40000000>;
 12	};
 13
 14	chosen {
 15		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/mmcblk0p2 rw rootwait";
 16	};
 17
 18	leds {
 19		compatible = "gpio-leds";
 20		pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>;
 21		pinctrl-names = "default";
 22
 23		wlan-act {
 24			label = "wlan-act";
 25			gpios = <&gpio0 0 1>;
 26		};
 27
 28		wlan-ap {
 29			label = "wlan-ap";
 30			gpios = <&gpio0 1 1>;
 31		};
 32
 33		status {
 34			label = "status";
 35			gpios = <&gpio0 2 1>;
 36		};
 37	};
 38
 39	regulators {
 40		compatible = "simple-bus";
 41		#address-cells = <1>;
 42		#size-cells = <0>;
 43
 44		usb_power: regulator@1 {
 45			compatible = "regulator-fixed";
 46			reg = <1>;
 47			regulator-name = "USB Power";
 48			regulator-min-microvolt = <5000000>;
 49			regulator-max-microvolt = <5000000>;
 50			enable-active-high;
 51			regulator-always-on;
 52			regulator-boot-on;
 53			gpio = <&gpio0 8 0>;
 54			pinctrl-0 = <&pmx_gpio_8>;
 55			pinctrl-names = "default";
 56		};
 57	};
 58};
 59
 60&uart0 { status = "okay"; };
 61&sata0 { status = "okay"; };
 62&i2c0 { status = "okay"; };
 63
 64/* Samsung M8G2F eMMC */
 65&sdio0 {
 66	status = "okay";
 67	non-removable;
 68	bus-width = <4>;
 69};
 70
 71/* Marvell SD8787 WLAN/BT */
 72&sdio1 {
 73	status = "okay";
 74	non-removable;
 75};
 76
 77&spi0 {
 78	status = "okay";
 79
 80	/* spi0.0: 2M Flash Macronix MX25L1605D */
 81	spi-flash@0 {
 82		compatible = "st,m25l1605d";
 83		spi-max-frequency = <86000000>;
 84		reg = <0>;
 85	};
 86};
 87
 88&pcie {
 89	status = "okay";
 90	/* Fresco Logic USB3.0 xHCI controller */
 91	pcie-port@0 {
 92		status = "okay";
 93		reset-gpios = <&gpio0 26 1>;
 94		reset-delay-us = <20000>;
 95		pinctrl-0 = <&pmx_camera_gpio>;
 96		pinctrl-names = "default";
 97	};
 98	/* Mini-PCIe slot */
 99	pcie-port@1 {
100		status = "okay";
101		reset-gpios = <&gpio0 25 1>;
102	};
103};