1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
  2/*
  3 * Copyright (C) 2020 Marvell International Ltd.
  4 *
  5 * Device tree for the CN9131-DB board.
  6 */
  7
  8#include "cn9130-db.dtsi"
  9
 10/ {
 11	compatible = "marvell,cn9131", "marvell,cn9130",
 12		     "marvell,armada-ap807-quad", "marvell,armada-ap807";
 13
 14	aliases {
 15		gpio3 = &cp1_gpio1;
 16		gpio4 = &cp1_gpio2;
 17		ethernet3 = &cp1_eth0;
 18		ethernet4 = &cp1_eth1;
 19	};
 20
 21	cp1_reg_usb3_vbus0: regulator-6 {
 22		compatible = "regulator-fixed";
 23		pinctrl-names = "default";
 24		pinctrl-0 = <&cp1_xhci0_vbus_pins>;
 25		regulator-name = "cp1-xhci0-vbus";
 26		regulator-min-microvolt = <5000000>;
 27		regulator-max-microvolt = <5000000>;
 28		enable-active-high;
 29		gpio = <&cp1_gpio1 3 GPIO_ACTIVE_HIGH>;
 30	};
 31
 32	cp1_usb3_0_phy0: usb-phy-3 {
 33		compatible = "usb-nop-xceiv";
 34		vcc-supply = <&cp1_reg_usb3_vbus0>;
 35	};
 36
 37	cp1_sfp_eth1: sfp-eth-2 {
 38		compatible = "sff,sfp";
 39		i2c-bus = <&cp1_i2c0>;
 40		los-gpios = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>;
 41		mod-def0-gpios = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>;
 42		tx-disable-gpios = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>;
 43		tx-fault-gpios = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>;
 44		pinctrl-names = "default";
 45		pinctrl-0 = <&cp1_sfp_pins>;
 46		/*
 47		 * SFP cages are unconnected on early PCBs because of an the I2C
 48		 * lanes not being connected. Prevent the port for being
 49		 * unusable by disabling the SFP node.
 50		 */
 51		status = "disabled";
 52	};
 53};
 54
 55/*
 56 * Instantiate the first slave CP115
 57 */
 58
 59#define CP11X_NAME		cp1
 60#define CP11X_BASE		f4000000
 61#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
 62#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
 63#define CP11X_PCIE0_BASE	f4600000
 64#define CP11X_PCIE1_BASE	f4620000
 65#define CP11X_PCIE2_BASE	f4640000
 66
 67#include "armada-cp115.dtsi"
 68
 69#undef CP11X_NAME
 70#undef CP11X_BASE
 71#undef CP11X_PCIEx_MEM_BASE
 72#undef CP11X_PCIEx_MEM_SIZE
 73#undef CP11X_PCIE0_BASE
 74#undef CP11X_PCIE1_BASE
 75#undef CP11X_PCIE2_BASE
 76
 77&cp1_crypto {
 78	status = "disabled";
 79};
 80
 81&cp1_ethernet {
 82	status = "okay";
 83};
 84
 85/* CON50 */
 86&cp1_eth0 {
 87	status = "okay";
 88	phy-mode = "10gbase-r";
 89	/* Generic PHY, providing serdes lanes */
 90	phys = <&cp1_comphy4 0>;
 91	managed = "in-band-status";
 92	sfp = <&cp1_sfp_eth1>;
 93};
 94
 95&cp1_gpio1 {
 96	status = "okay";
 97};
 98
 99&cp1_gpio2 {
100	status = "okay";
101};
102
103&cp1_i2c0 {
104	status = "okay";
105	pinctrl-names = "default";
106	pinctrl-0 = <&cp1_i2c0_pins>;
107	clock-frequency = <100000>;
108};
109
110/* CON40 */
111&cp1_pcie0 {
112	pinctrl-names = "default";
113	pinctrl-0 = <&cp1_pcie_reset_pins>;
114	num-lanes = <2>;
115	num-viewport = <8>;
116	marvell,reset-gpio = <&cp1_gpio1 0 GPIO_ACTIVE_HIGH>;
117	status = "okay";
118	/* Generic PHY, providing serdes lanes */
119	phys = <&cp1_comphy0 0
120		&cp1_comphy1 0>;
121};
122
123&cp1_sata0 {
124	status = "okay";
125
126	/* CON32 */
127	sata-port@1 {
128		/* Generic PHY, providing serdes lanes */
129		phys = <&cp1_comphy5 1>;
130	};
131};
132
133/* U24 */
134&cp1_spi1 {
135	status = "okay";
136	pinctrl-names = "default";
137	pinctrl-0 = <&cp1_spi0_pins>;
138	reg = <0x700680 0x50>;
139
140	flash@0 {
141		compatible = "jedec,spi-nor";
142		reg = <0x0>;
143		/* On-board MUX does not allow higher frequencies */
144		spi-max-frequency = <40000000>;
145
146		partitions {
147			compatible = "fixed-partitions";
148			#address-cells = <1>;
149			#size-cells = <1>;
150
151			partition@0 {
152				label = "U-Boot-1";
153				reg = <0x0 0x200000>;
154			};
155
156			partition@400000 {
157				label = "Filesystem-1";
158				reg = <0x200000 0xe00000>;
159			};
160		};
161	};
162
163};
164
165&cp1_syscon0 {
166	cp1_pinctrl: pinctrl {
167		compatible = "marvell,cp115-standalone-pinctrl";
168
169		cp1_i2c0_pins: cp1-i2c-pins-0 {
170			marvell,pins = "mpp37", "mpp38";
171			marvell,function = "i2c0";
172		};
173		cp1_spi0_pins: cp1-spi-pins-0 {
174			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
175			marvell,function = "spi1";
176		};
177		cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins {
178			marvell,pins = "mpp3";
179			marvell,function = "gpio";
180		};
181		cp1_sfp_pins: sfp-pins {
182			marvell,pins = "mpp8", "mpp9", "mpp10", "mpp11";
183			marvell,function = "gpio";
184		};
185		cp1_pcie_reset_pins: cp1-pcie-reset-pins {
186			marvell,pins = "mpp0";
187			marvell,function = "gpio";
188		};
189	};
190};
191
192/* CON58 */
193&cp1_utmi {
194	status = "okay";
195};
196
197&cp1_usb3_1 {
198	status = "okay";
199	usb-phy = <&cp1_usb3_0_phy0>;
200	/* Generic PHY, providing serdes lanes */
201	phys = <&cp1_comphy3 1>, <&cp1_utmi1>;
202	phy-names = "usb", "utmi";
203	dr_mode = "host";
204};