Loading...
1// SPDX-License-Identifier: GPL-2.0+
2// Copyright 2018 IBM Corporation
3
4#include <linux/clk.h>
5#include <linux/dma-mapping.h>
6#include <linux/irq.h>
7#include <linux/mfd/syscon.h>
8#include <linux/module.h>
9#include <linux/of.h>
10#include <linux/of_reserved_mem.h>
11#include <linux/platform_device.h>
12#include <linux/regmap.h>
13#include <linux/reset.h>
14
15#include <drm/drm_atomic_helper.h>
16#include <drm/drm_crtc_helper.h>
17#include <drm/drm_device.h>
18#include <drm/drm_fb_cma_helper.h>
19#include <drm/drm_fb_helper.h>
20#include <drm/drm_gem_cma_helper.h>
21#include <drm/drm_gem_framebuffer_helper.h>
22#include <drm/drm_probe_helper.h>
23#include <drm/drm_simple_kms_helper.h>
24#include <drm/drm_vblank.h>
25#include <drm/drm_drv.h>
26
27#include "aspeed_gfx.h"
28
29/**
30 * DOC: ASPEED GFX Driver
31 *
32 * This driver is for the ASPEED BMC SoC's 'GFX' display hardware, also called
33 * the 'SOC Display Controller' in the datasheet. This driver runs on the ARM
34 * based BMC systems, unlike the ast driver which runs on a host CPU and is for
35 * a PCIe graphics device.
36 *
37 * The AST2500 supports a total of 3 output paths:
38 *
39 * 1. VGA output, the output target can choose either or both to the DAC
40 * or DVO interface.
41 *
42 * 2. Graphics CRT output, the output target can choose either or both to
43 * the DAC or DVO interface.
44 *
45 * 3. Video input from DVO, the video input can be used for video engine
46 * capture or DAC display output.
47 *
48 * Output options are selected in SCU2C.
49 *
50 * The "VGA mode" device is the PCI attached controller. The "Graphics CRT"
51 * is the ARM's internal display controller.
52 *
53 * The driver only supports a simple configuration consisting of a 40MHz
54 * pixel clock, fixed by hardware limitations, and the VGA output path.
55 *
56 * The driver was written with the 'AST2500 Software Programming Guide' v17,
57 * which is available under NDA from ASPEED.
58 */
59
60static const struct drm_mode_config_funcs aspeed_gfx_mode_config_funcs = {
61 .fb_create = drm_gem_fb_create,
62 .atomic_check = drm_atomic_helper_check,
63 .atomic_commit = drm_atomic_helper_commit,
64};
65
66static void aspeed_gfx_setup_mode_config(struct drm_device *drm)
67{
68 drm_mode_config_init(drm);
69
70 drm->mode_config.min_width = 0;
71 drm->mode_config.min_height = 0;
72 drm->mode_config.max_width = 800;
73 drm->mode_config.max_height = 600;
74 drm->mode_config.funcs = &aspeed_gfx_mode_config_funcs;
75}
76
77static irqreturn_t aspeed_gfx_irq_handler(int irq, void *data)
78{
79 struct drm_device *drm = data;
80 struct aspeed_gfx *priv = to_aspeed_gfx(drm);
81 u32 reg;
82
83 reg = readl(priv->base + CRT_CTRL1);
84
85 if (reg & CRT_CTRL_VERTICAL_INTR_STS) {
86 drm_crtc_handle_vblank(&priv->pipe.crtc);
87 writel(reg, priv->base + CRT_CTRL1);
88 return IRQ_HANDLED;
89 }
90
91 return IRQ_NONE;
92}
93
94
95
96static int aspeed_gfx_load(struct drm_device *drm)
97{
98 struct platform_device *pdev = to_platform_device(drm->dev);
99 struct aspeed_gfx *priv = to_aspeed_gfx(drm);
100 struct resource *res;
101 int ret;
102
103 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
104 priv->base = devm_ioremap_resource(drm->dev, res);
105 if (IS_ERR(priv->base))
106 return PTR_ERR(priv->base);
107
108 priv->scu = syscon_regmap_lookup_by_compatible("aspeed,ast2500-scu");
109 if (IS_ERR(priv->scu)) {
110 dev_err(&pdev->dev, "failed to find SCU regmap\n");
111 return PTR_ERR(priv->scu);
112 }
113
114 ret = of_reserved_mem_device_init(drm->dev);
115 if (ret) {
116 dev_err(&pdev->dev,
117 "failed to initialize reserved mem: %d\n", ret);
118 return ret;
119 }
120
121 ret = dma_set_mask_and_coherent(drm->dev, DMA_BIT_MASK(32));
122 if (ret) {
123 dev_err(&pdev->dev, "failed to set DMA mask: %d\n", ret);
124 return ret;
125 }
126
127 priv->rst = devm_reset_control_get_exclusive(&pdev->dev, NULL);
128 if (IS_ERR(priv->rst)) {
129 dev_err(&pdev->dev,
130 "missing or invalid reset controller device tree entry");
131 return PTR_ERR(priv->rst);
132 }
133 reset_control_deassert(priv->rst);
134
135 priv->clk = devm_clk_get(drm->dev, NULL);
136 if (IS_ERR(priv->clk)) {
137 dev_err(&pdev->dev,
138 "missing or invalid clk device tree entry");
139 return PTR_ERR(priv->clk);
140 }
141 clk_prepare_enable(priv->clk);
142
143 /* Sanitize control registers */
144 writel(0, priv->base + CRT_CTRL1);
145 writel(0, priv->base + CRT_CTRL2);
146
147 aspeed_gfx_setup_mode_config(drm);
148
149 ret = drm_vblank_init(drm, 1);
150 if (ret < 0) {
151 dev_err(drm->dev, "Failed to initialise vblank\n");
152 return ret;
153 }
154
155 ret = aspeed_gfx_create_output(drm);
156 if (ret < 0) {
157 dev_err(drm->dev, "Failed to create outputs\n");
158 return ret;
159 }
160
161 ret = aspeed_gfx_create_pipe(drm);
162 if (ret < 0) {
163 dev_err(drm->dev, "Cannot setup simple display pipe\n");
164 return ret;
165 }
166
167 ret = devm_request_irq(drm->dev, platform_get_irq(pdev, 0),
168 aspeed_gfx_irq_handler, 0, "aspeed gfx", drm);
169 if (ret < 0) {
170 dev_err(drm->dev, "Failed to install IRQ handler\n");
171 return ret;
172 }
173
174 drm_mode_config_reset(drm);
175
176 return 0;
177}
178
179static void aspeed_gfx_unload(struct drm_device *drm)
180{
181 drm_kms_helper_poll_fini(drm);
182 drm_mode_config_cleanup(drm);
183}
184
185DEFINE_DRM_GEM_CMA_FOPS(fops);
186
187static struct drm_driver aspeed_gfx_driver = {
188 .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC,
189 .gem_create_object = drm_gem_cma_create_object_default_funcs,
190 .dumb_create = drm_gem_cma_dumb_create,
191 .prime_handle_to_fd = drm_gem_prime_handle_to_fd,
192 .prime_fd_to_handle = drm_gem_prime_fd_to_handle,
193 .gem_prime_import_sg_table = drm_gem_cma_prime_import_sg_table,
194 .gem_prime_mmap = drm_gem_prime_mmap,
195 .fops = &fops,
196 .name = "aspeed-gfx-drm",
197 .desc = "ASPEED GFX DRM",
198 .date = "20180319",
199 .major = 1,
200 .minor = 0,
201};
202
203static const struct of_device_id aspeed_gfx_match[] = {
204 { .compatible = "aspeed,ast2500-gfx" },
205 { }
206};
207
208static int aspeed_gfx_probe(struct platform_device *pdev)
209{
210 struct aspeed_gfx *priv;
211 int ret;
212
213 priv = devm_drm_dev_alloc(&pdev->dev, &aspeed_gfx_driver,
214 struct aspeed_gfx, drm);
215 if (IS_ERR(priv))
216 return PTR_ERR(priv);
217
218 ret = aspeed_gfx_load(&priv->drm);
219 if (ret)
220 return ret;
221
222 ret = drm_dev_register(&priv->drm, 0);
223 if (ret)
224 goto err_unload;
225
226 drm_fbdev_generic_setup(&priv->drm, 32);
227 return 0;
228
229err_unload:
230 aspeed_gfx_unload(&priv->drm);
231
232 return ret;
233}
234
235static int aspeed_gfx_remove(struct platform_device *pdev)
236{
237 struct drm_device *drm = platform_get_drvdata(pdev);
238
239 drm_dev_unregister(drm);
240 aspeed_gfx_unload(drm);
241
242 return 0;
243}
244
245static struct platform_driver aspeed_gfx_platform_driver = {
246 .probe = aspeed_gfx_probe,
247 .remove = aspeed_gfx_remove,
248 .driver = {
249 .name = "aspeed_gfx",
250 .of_match_table = aspeed_gfx_match,
251 },
252};
253
254module_platform_driver(aspeed_gfx_platform_driver);
255
256MODULE_AUTHOR("Joel Stanley <joel@jms.id.au>");
257MODULE_DESCRIPTION("ASPEED BMC DRM/KMS driver");
258MODULE_LICENSE("GPL");
1// SPDX-License-Identifier: GPL-2.0+
2// Copyright 2018 IBM Corporation
3
4#include <linux/clk.h>
5#include <linux/dma-mapping.h>
6#include <linux/irq.h>
7#include <linux/mfd/syscon.h>
8#include <linux/module.h>
9#include <linux/mod_devicetable.h>
10#include <linux/of_reserved_mem.h>
11#include <linux/platform_device.h>
12#include <linux/property.h>
13#include <linux/regmap.h>
14#include <linux/reset.h>
15
16#include <drm/drm_atomic_helper.h>
17#include <drm/drm_device.h>
18#include <drm/drm_fbdev_dma.h>
19#include <drm/drm_gem_dma_helper.h>
20#include <drm/drm_gem_framebuffer_helper.h>
21#include <drm/drm_module.h>
22#include <drm/drm_probe_helper.h>
23#include <drm/drm_simple_kms_helper.h>
24#include <drm/drm_vblank.h>
25#include <drm/drm_drv.h>
26
27#include "aspeed_gfx.h"
28
29/**
30 * DOC: ASPEED GFX Driver
31 *
32 * This driver is for the ASPEED BMC SoC's 'GFX' display hardware, also called
33 * the 'SOC Display Controller' in the datasheet. This driver runs on the ARM
34 * based BMC systems, unlike the ast driver which runs on a host CPU and is for
35 * a PCIe graphics device.
36 *
37 * The AST2500 supports a total of 3 output paths:
38 *
39 * 1. VGA output, the output target can choose either or both to the DAC
40 * or DVO interface.
41 *
42 * 2. Graphics CRT output, the output target can choose either or both to
43 * the DAC or DVO interface.
44 *
45 * 3. Video input from DVO, the video input can be used for video engine
46 * capture or DAC display output.
47 *
48 * Output options are selected in SCU2C.
49 *
50 * The "VGA mode" device is the PCI attached controller. The "Graphics CRT"
51 * is the ARM's internal display controller.
52 *
53 * The driver only supports a simple configuration consisting of a 40MHz
54 * pixel clock, fixed by hardware limitations, and the VGA output path.
55 *
56 * The driver was written with the 'AST2500 Software Programming Guide' v17,
57 * which is available under NDA from ASPEED.
58 */
59
60struct aspeed_gfx_config {
61 u32 dac_reg; /* DAC register in SCU */
62 u32 int_clear_reg; /* Interrupt clear register */
63 u32 vga_scratch_reg; /* VGA scratch register in SCU */
64 u32 throd_val; /* Default Threshold Seting */
65 u32 scan_line_max; /* Max memory size of one scan line */
66};
67
68static const struct aspeed_gfx_config ast2400_config = {
69 .dac_reg = 0x2c,
70 .int_clear_reg = 0x60,
71 .vga_scratch_reg = 0x50,
72 .throd_val = CRT_THROD_LOW(0x1e) | CRT_THROD_HIGH(0x12),
73 .scan_line_max = 64,
74};
75
76static const struct aspeed_gfx_config ast2500_config = {
77 .dac_reg = 0x2c,
78 .int_clear_reg = 0x60,
79 .vga_scratch_reg = 0x50,
80 .throd_val = CRT_THROD_LOW(0x24) | CRT_THROD_HIGH(0x3c),
81 .scan_line_max = 128,
82};
83
84static const struct aspeed_gfx_config ast2600_config = {
85 .dac_reg = 0xc0,
86 .int_clear_reg = 0x68,
87 .vga_scratch_reg = 0x50,
88 .throd_val = CRT_THROD_LOW(0x50) | CRT_THROD_HIGH(0x70),
89 .scan_line_max = 128,
90};
91
92static const struct of_device_id aspeed_gfx_match[] = {
93 { .compatible = "aspeed,ast2400-gfx", .data = &ast2400_config },
94 { .compatible = "aspeed,ast2500-gfx", .data = &ast2500_config },
95 { .compatible = "aspeed,ast2600-gfx", .data = &ast2600_config },
96 { },
97};
98MODULE_DEVICE_TABLE(of, aspeed_gfx_match);
99
100static const struct drm_mode_config_funcs aspeed_gfx_mode_config_funcs = {
101 .fb_create = drm_gem_fb_create,
102 .atomic_check = drm_atomic_helper_check,
103 .atomic_commit = drm_atomic_helper_commit,
104};
105
106static int aspeed_gfx_setup_mode_config(struct drm_device *drm)
107{
108 int ret;
109
110 ret = drmm_mode_config_init(drm);
111 if (ret)
112 return ret;
113
114 drm->mode_config.min_width = 0;
115 drm->mode_config.min_height = 0;
116 drm->mode_config.max_width = 800;
117 drm->mode_config.max_height = 600;
118 drm->mode_config.funcs = &aspeed_gfx_mode_config_funcs;
119
120 return ret;
121}
122
123static irqreturn_t aspeed_gfx_irq_handler(int irq, void *data)
124{
125 struct drm_device *drm = data;
126 struct aspeed_gfx *priv = to_aspeed_gfx(drm);
127 u32 reg;
128
129 reg = readl(priv->base + CRT_CTRL1);
130
131 if (reg & CRT_CTRL_VERTICAL_INTR_STS) {
132 drm_crtc_handle_vblank(&priv->pipe.crtc);
133 writel(reg, priv->base + priv->int_clr_reg);
134 return IRQ_HANDLED;
135 }
136
137 return IRQ_NONE;
138}
139
140static int aspeed_gfx_load(struct drm_device *drm)
141{
142 struct platform_device *pdev = to_platform_device(drm->dev);
143 struct aspeed_gfx *priv = to_aspeed_gfx(drm);
144 struct device_node *np = pdev->dev.of_node;
145 const struct aspeed_gfx_config *config;
146 struct resource *res;
147 int ret;
148
149 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
150 priv->base = devm_ioremap_resource(drm->dev, res);
151 if (IS_ERR(priv->base))
152 return PTR_ERR(priv->base);
153
154 config = device_get_match_data(&pdev->dev);
155 if (!config)
156 return -EINVAL;
157
158 priv->dac_reg = config->dac_reg;
159 priv->int_clr_reg = config->int_clear_reg;
160 priv->vga_scratch_reg = config->vga_scratch_reg;
161 priv->throd_val = config->throd_val;
162 priv->scan_line_max = config->scan_line_max;
163
164 priv->scu = syscon_regmap_lookup_by_phandle(np, "syscon");
165 if (IS_ERR(priv->scu)) {
166 priv->scu = syscon_regmap_lookup_by_compatible("aspeed,ast2500-scu");
167 if (IS_ERR(priv->scu)) {
168 dev_err(&pdev->dev, "failed to find SCU regmap\n");
169 return PTR_ERR(priv->scu);
170 }
171 }
172
173 ret = of_reserved_mem_device_init(drm->dev);
174 if (ret) {
175 dev_err(&pdev->dev,
176 "failed to initialize reserved mem: %d\n", ret);
177 return ret;
178 }
179
180 ret = dma_set_mask_and_coherent(drm->dev, DMA_BIT_MASK(32));
181 if (ret) {
182 dev_err(&pdev->dev, "failed to set DMA mask: %d\n", ret);
183 return ret;
184 }
185
186 priv->rst = devm_reset_control_get_exclusive(&pdev->dev, NULL);
187 if (IS_ERR(priv->rst)) {
188 dev_err(&pdev->dev,
189 "missing or invalid reset controller device tree entry");
190 return PTR_ERR(priv->rst);
191 }
192 reset_control_deassert(priv->rst);
193
194 priv->clk = devm_clk_get(drm->dev, NULL);
195 if (IS_ERR(priv->clk)) {
196 dev_err(&pdev->dev,
197 "missing or invalid clk device tree entry");
198 return PTR_ERR(priv->clk);
199 }
200 clk_prepare_enable(priv->clk);
201
202 /* Sanitize control registers */
203 writel(0, priv->base + CRT_CTRL1);
204 writel(0, priv->base + CRT_CTRL2);
205
206 ret = aspeed_gfx_setup_mode_config(drm);
207 if (ret < 0)
208 return ret;
209
210 ret = drm_vblank_init(drm, 1);
211 if (ret < 0) {
212 dev_err(drm->dev, "Failed to initialise vblank\n");
213 return ret;
214 }
215
216 ret = aspeed_gfx_create_output(drm);
217 if (ret < 0) {
218 dev_err(drm->dev, "Failed to create outputs\n");
219 return ret;
220 }
221
222 ret = aspeed_gfx_create_pipe(drm);
223 if (ret < 0) {
224 dev_err(drm->dev, "Cannot setup simple display pipe\n");
225 return ret;
226 }
227
228 ret = devm_request_irq(drm->dev, platform_get_irq(pdev, 0),
229 aspeed_gfx_irq_handler, 0, "aspeed gfx", drm);
230 if (ret < 0) {
231 dev_err(drm->dev, "Failed to install IRQ handler\n");
232 return ret;
233 }
234
235 drm_mode_config_reset(drm);
236
237 return 0;
238}
239
240static void aspeed_gfx_unload(struct drm_device *drm)
241{
242 drm_kms_helper_poll_fini(drm);
243}
244
245DEFINE_DRM_GEM_DMA_FOPS(fops);
246
247static const struct drm_driver aspeed_gfx_driver = {
248 .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC,
249 DRM_GEM_DMA_DRIVER_OPS,
250 .fops = &fops,
251 .name = "aspeed-gfx-drm",
252 .desc = "ASPEED GFX DRM",
253 .date = "20180319",
254 .major = 1,
255 .minor = 0,
256};
257
258static ssize_t dac_mux_store(struct device *dev, struct device_attribute *attr,
259 const char *buf, size_t count)
260{
261 struct aspeed_gfx *priv = dev_get_drvdata(dev);
262 u32 val;
263 int rc;
264
265 rc = kstrtou32(buf, 0, &val);
266 if (rc)
267 return rc;
268
269 if (val > 3)
270 return -EINVAL;
271
272 rc = regmap_update_bits(priv->scu, priv->dac_reg, 0x30000, val << 16);
273 if (rc < 0)
274 return 0;
275
276 return count;
277}
278
279static ssize_t dac_mux_show(struct device *dev, struct device_attribute *attr, char *buf)
280{
281 struct aspeed_gfx *priv = dev_get_drvdata(dev);
282 u32 reg;
283 int rc;
284
285 rc = regmap_read(priv->scu, priv->dac_reg, ®);
286 if (rc)
287 return rc;
288
289 return sprintf(buf, "%u\n", (reg >> 16) & 0x3);
290}
291static DEVICE_ATTR_RW(dac_mux);
292
293static ssize_t
294vga_pw_show(struct device *dev, struct device_attribute *attr, char *buf)
295{
296 struct aspeed_gfx *priv = dev_get_drvdata(dev);
297 u32 reg;
298 int rc;
299
300 rc = regmap_read(priv->scu, priv->vga_scratch_reg, ®);
301 if (rc)
302 return rc;
303
304 return sprintf(buf, "%u\n", reg);
305}
306static DEVICE_ATTR_RO(vga_pw);
307
308static struct attribute *aspeed_sysfs_entries[] = {
309 &dev_attr_vga_pw.attr,
310 &dev_attr_dac_mux.attr,
311 NULL,
312};
313
314static struct attribute_group aspeed_sysfs_attr_group = {
315 .attrs = aspeed_sysfs_entries,
316};
317
318static int aspeed_gfx_probe(struct platform_device *pdev)
319{
320 struct aspeed_gfx *priv;
321 int ret;
322
323 priv = devm_drm_dev_alloc(&pdev->dev, &aspeed_gfx_driver,
324 struct aspeed_gfx, drm);
325 if (IS_ERR(priv))
326 return PTR_ERR(priv);
327
328 ret = aspeed_gfx_load(&priv->drm);
329 if (ret)
330 return ret;
331
332 platform_set_drvdata(pdev, priv);
333
334 ret = sysfs_create_group(&pdev->dev.kobj, &aspeed_sysfs_attr_group);
335 if (ret)
336 return ret;
337
338 ret = drm_dev_register(&priv->drm, 0);
339 if (ret)
340 goto err_unload;
341
342 drm_fbdev_dma_setup(&priv->drm, 32);
343 return 0;
344
345err_unload:
346 sysfs_remove_group(&pdev->dev.kobj, &aspeed_sysfs_attr_group);
347 aspeed_gfx_unload(&priv->drm);
348
349 return ret;
350}
351
352static void aspeed_gfx_remove(struct platform_device *pdev)
353{
354 struct drm_device *drm = platform_get_drvdata(pdev);
355
356 sysfs_remove_group(&pdev->dev.kobj, &aspeed_sysfs_attr_group);
357 drm_dev_unregister(drm);
358 aspeed_gfx_unload(drm);
359 drm_atomic_helper_shutdown(drm);
360}
361
362static void aspeed_gfx_shutdown(struct platform_device *pdev)
363{
364 drm_atomic_helper_shutdown(platform_get_drvdata(pdev));
365}
366
367static struct platform_driver aspeed_gfx_platform_driver = {
368 .probe = aspeed_gfx_probe,
369 .remove_new = aspeed_gfx_remove,
370 .shutdown = aspeed_gfx_shutdown,
371 .driver = {
372 .name = "aspeed_gfx",
373 .of_match_table = aspeed_gfx_match,
374 },
375};
376
377drm_module_platform_driver(aspeed_gfx_platform_driver);
378
379MODULE_AUTHOR("Joel Stanley <joel@jms.id.au>");
380MODULE_DESCRIPTION("ASPEED BMC DRM/KMS driver");
381MODULE_LICENSE("GPL");