Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Copyright 2016 IBM Corporation
4 *
5 * Joel Stanley <joel@jms.id.au>
6 */
7
8#include <linux/delay.h>
9#include <linux/io.h>
10#include <linux/kernel.h>
11#include <linux/module.h>
12#include <linux/of.h>
13#include <linux/platform_device.h>
14#include <linux/watchdog.h>
15
16struct aspeed_wdt {
17 struct watchdog_device wdd;
18 void __iomem *base;
19 u32 ctrl;
20};
21
22struct aspeed_wdt_config {
23 u32 ext_pulse_width_mask;
24};
25
26static const struct aspeed_wdt_config ast2400_config = {
27 .ext_pulse_width_mask = 0xff,
28};
29
30static const struct aspeed_wdt_config ast2500_config = {
31 .ext_pulse_width_mask = 0xfffff,
32};
33
34static const struct of_device_id aspeed_wdt_of_table[] = {
35 { .compatible = "aspeed,ast2400-wdt", .data = &ast2400_config },
36 { .compatible = "aspeed,ast2500-wdt", .data = &ast2500_config },
37 { .compatible = "aspeed,ast2600-wdt", .data = &ast2500_config },
38 { },
39};
40MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table);
41
42#define WDT_STATUS 0x00
43#define WDT_RELOAD_VALUE 0x04
44#define WDT_RESTART 0x08
45#define WDT_CTRL 0x0C
46#define WDT_CTRL_BOOT_SECONDARY BIT(7)
47#define WDT_CTRL_RESET_MODE_SOC (0x00 << 5)
48#define WDT_CTRL_RESET_MODE_FULL_CHIP (0x01 << 5)
49#define WDT_CTRL_RESET_MODE_ARM_CPU (0x10 << 5)
50#define WDT_CTRL_1MHZ_CLK BIT(4)
51#define WDT_CTRL_WDT_EXT BIT(3)
52#define WDT_CTRL_WDT_INTR BIT(2)
53#define WDT_CTRL_RESET_SYSTEM BIT(1)
54#define WDT_CTRL_ENABLE BIT(0)
55#define WDT_TIMEOUT_STATUS 0x10
56#define WDT_TIMEOUT_STATUS_BOOT_SECONDARY BIT(1)
57#define WDT_CLEAR_TIMEOUT_STATUS 0x14
58#define WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION BIT(0)
59
60/*
61 * WDT_RESET_WIDTH controls the characteristics of the external pulse (if
62 * enabled), specifically:
63 *
64 * * Pulse duration
65 * * Drive mode: push-pull vs open-drain
66 * * Polarity: Active high or active low
67 *
68 * Pulse duration configuration is available on both the AST2400 and AST2500,
69 * though the field changes between SoCs:
70 *
71 * AST2400: Bits 7:0
72 * AST2500: Bits 19:0
73 *
74 * This difference is captured in struct aspeed_wdt_config.
75 *
76 * The AST2500 exposes the drive mode and polarity options, but not in a
77 * regular fashion. For read purposes, bit 31 represents active high or low,
78 * and bit 30 represents push-pull or open-drain. With respect to write, magic
79 * values need to be written to the top byte to change the state of the drive
80 * mode and polarity bits. Any other value written to the top byte has no
81 * effect on the state of the drive mode or polarity bits. However, the pulse
82 * width value must be preserved (as desired) if written.
83 */
84#define WDT_RESET_WIDTH 0x18
85#define WDT_RESET_WIDTH_ACTIVE_HIGH BIT(31)
86#define WDT_ACTIVE_HIGH_MAGIC (0xA5 << 24)
87#define WDT_ACTIVE_LOW_MAGIC (0x5A << 24)
88#define WDT_RESET_WIDTH_PUSH_PULL BIT(30)
89#define WDT_PUSH_PULL_MAGIC (0xA8 << 24)
90#define WDT_OPEN_DRAIN_MAGIC (0x8A << 24)
91
92#define WDT_RESTART_MAGIC 0x4755
93
94/* 32 bits at 1MHz, in milliseconds */
95#define WDT_MAX_TIMEOUT_MS 4294967
96#define WDT_DEFAULT_TIMEOUT 30
97#define WDT_RATE_1MHZ 1000000
98
99static struct aspeed_wdt *to_aspeed_wdt(struct watchdog_device *wdd)
100{
101 return container_of(wdd, struct aspeed_wdt, wdd);
102}
103
104static void aspeed_wdt_enable(struct aspeed_wdt *wdt, int count)
105{
106 wdt->ctrl |= WDT_CTRL_ENABLE;
107
108 writel(0, wdt->base + WDT_CTRL);
109 writel(count, wdt->base + WDT_RELOAD_VALUE);
110 writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART);
111 writel(wdt->ctrl, wdt->base + WDT_CTRL);
112}
113
114static int aspeed_wdt_start(struct watchdog_device *wdd)
115{
116 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
117
118 aspeed_wdt_enable(wdt, wdd->timeout * WDT_RATE_1MHZ);
119
120 return 0;
121}
122
123static int aspeed_wdt_stop(struct watchdog_device *wdd)
124{
125 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
126
127 wdt->ctrl &= ~WDT_CTRL_ENABLE;
128 writel(wdt->ctrl, wdt->base + WDT_CTRL);
129
130 return 0;
131}
132
133static int aspeed_wdt_ping(struct watchdog_device *wdd)
134{
135 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
136
137 writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART);
138
139 return 0;
140}
141
142static int aspeed_wdt_set_timeout(struct watchdog_device *wdd,
143 unsigned int timeout)
144{
145 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
146 u32 actual;
147
148 wdd->timeout = timeout;
149
150 actual = min(timeout, wdd->max_hw_heartbeat_ms * 1000);
151
152 writel(actual * WDT_RATE_1MHZ, wdt->base + WDT_RELOAD_VALUE);
153 writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART);
154
155 return 0;
156}
157
158static int aspeed_wdt_restart(struct watchdog_device *wdd,
159 unsigned long action, void *data)
160{
161 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
162
163 wdt->ctrl &= ~WDT_CTRL_BOOT_SECONDARY;
164 aspeed_wdt_enable(wdt, 128 * WDT_RATE_1MHZ / 1000);
165
166 mdelay(1000);
167
168 return 0;
169}
170
171/* access_cs0 shows if cs0 is accessible, hence the reverted bit */
172static ssize_t access_cs0_show(struct device *dev,
173 struct device_attribute *attr, char *buf)
174{
175 struct aspeed_wdt *wdt = dev_get_drvdata(dev);
176 u32 status = readl(wdt->base + WDT_TIMEOUT_STATUS);
177
178 return sprintf(buf, "%u\n",
179 !(status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY));
180}
181
182static ssize_t access_cs0_store(struct device *dev,
183 struct device_attribute *attr, const char *buf,
184 size_t size)
185{
186 struct aspeed_wdt *wdt = dev_get_drvdata(dev);
187 unsigned long val;
188
189 if (kstrtoul(buf, 10, &val))
190 return -EINVAL;
191
192 if (val)
193 writel(WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION,
194 wdt->base + WDT_CLEAR_TIMEOUT_STATUS);
195
196 return size;
197}
198
199/*
200 * This attribute exists only if the system has booted from the alternate
201 * flash with 'alt-boot' option.
202 *
203 * At alternate flash the 'access_cs0' sysfs node provides:
204 * ast2400: a way to get access to the primary SPI flash chip at CS0
205 * after booting from the alternate chip at CS1.
206 * ast2500: a way to restore the normal address mapping from
207 * (CS0->CS1, CS1->CS0) to (CS0->CS0, CS1->CS1).
208 *
209 * Clearing the boot code selection and timeout counter also resets to the
210 * initial state the chip select line mapping. When the SoC is in normal
211 * mapping state (i.e. booted from CS0), clearing those bits does nothing for
212 * both versions of the SoC. For alternate boot mode (booted from CS1 due to
213 * wdt2 expiration) the behavior differs as described above.
214 *
215 * This option can be used with wdt2 (watchdog1) only.
216 */
217static DEVICE_ATTR_RW(access_cs0);
218
219static struct attribute *bswitch_attrs[] = {
220 &dev_attr_access_cs0.attr,
221 NULL
222};
223ATTRIBUTE_GROUPS(bswitch);
224
225static const struct watchdog_ops aspeed_wdt_ops = {
226 .start = aspeed_wdt_start,
227 .stop = aspeed_wdt_stop,
228 .ping = aspeed_wdt_ping,
229 .set_timeout = aspeed_wdt_set_timeout,
230 .restart = aspeed_wdt_restart,
231 .owner = THIS_MODULE,
232};
233
234static const struct watchdog_info aspeed_wdt_info = {
235 .options = WDIOF_KEEPALIVEPING
236 | WDIOF_MAGICCLOSE
237 | WDIOF_SETTIMEOUT,
238 .identity = KBUILD_MODNAME,
239};
240
241static int aspeed_wdt_probe(struct platform_device *pdev)
242{
243 struct device *dev = &pdev->dev;
244 const struct aspeed_wdt_config *config;
245 const struct of_device_id *ofdid;
246 struct aspeed_wdt *wdt;
247 struct device_node *np;
248 const char *reset_type;
249 u32 duration;
250 u32 status;
251 int ret;
252
253 wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
254 if (!wdt)
255 return -ENOMEM;
256
257 wdt->base = devm_platform_ioremap_resource(pdev, 0);
258 if (IS_ERR(wdt->base))
259 return PTR_ERR(wdt->base);
260
261 wdt->wdd.info = &aspeed_wdt_info;
262 wdt->wdd.ops = &aspeed_wdt_ops;
263 wdt->wdd.max_hw_heartbeat_ms = WDT_MAX_TIMEOUT_MS;
264 wdt->wdd.parent = dev;
265
266 wdt->wdd.timeout = WDT_DEFAULT_TIMEOUT;
267 watchdog_init_timeout(&wdt->wdd, 0, dev);
268
269 np = dev->of_node;
270
271 ofdid = of_match_node(aspeed_wdt_of_table, np);
272 if (!ofdid)
273 return -EINVAL;
274 config = ofdid->data;
275
276 /*
277 * On clock rates:
278 * - ast2400 wdt can run at PCLK, or 1MHz
279 * - ast2500 only runs at 1MHz, hard coding bit 4 to 1
280 * - ast2600 always runs at 1MHz
281 *
282 * Set the ast2400 to run at 1MHz as it simplifies the driver.
283 */
284 if (of_device_is_compatible(np, "aspeed,ast2400-wdt"))
285 wdt->ctrl = WDT_CTRL_1MHZ_CLK;
286
287 /*
288 * Control reset on a per-device basis to ensure the
289 * host is not affected by a BMC reboot
290 */
291 ret = of_property_read_string(np, "aspeed,reset-type", &reset_type);
292 if (ret) {
293 wdt->ctrl |= WDT_CTRL_RESET_MODE_SOC | WDT_CTRL_RESET_SYSTEM;
294 } else {
295 if (!strcmp(reset_type, "cpu"))
296 wdt->ctrl |= WDT_CTRL_RESET_MODE_ARM_CPU |
297 WDT_CTRL_RESET_SYSTEM;
298 else if (!strcmp(reset_type, "soc"))
299 wdt->ctrl |= WDT_CTRL_RESET_MODE_SOC |
300 WDT_CTRL_RESET_SYSTEM;
301 else if (!strcmp(reset_type, "system"))
302 wdt->ctrl |= WDT_CTRL_RESET_MODE_FULL_CHIP |
303 WDT_CTRL_RESET_SYSTEM;
304 else if (strcmp(reset_type, "none"))
305 return -EINVAL;
306 }
307 if (of_property_read_bool(np, "aspeed,external-signal"))
308 wdt->ctrl |= WDT_CTRL_WDT_EXT;
309 if (of_property_read_bool(np, "aspeed,alt-boot"))
310 wdt->ctrl |= WDT_CTRL_BOOT_SECONDARY;
311
312 if (readl(wdt->base + WDT_CTRL) & WDT_CTRL_ENABLE) {
313 /*
314 * The watchdog is running, but invoke aspeed_wdt_start() to
315 * write wdt->ctrl to WDT_CTRL to ensure the watchdog's
316 * configuration conforms to the driver's expectations.
317 * Primarily, ensure we're using the 1MHz clock source.
318 */
319 aspeed_wdt_start(&wdt->wdd);
320 set_bit(WDOG_HW_RUNNING, &wdt->wdd.status);
321 }
322
323 if ((of_device_is_compatible(np, "aspeed,ast2500-wdt")) ||
324 (of_device_is_compatible(np, "aspeed,ast2600-wdt"))) {
325 u32 reg = readl(wdt->base + WDT_RESET_WIDTH);
326
327 reg &= config->ext_pulse_width_mask;
328 if (of_property_read_bool(np, "aspeed,ext-push-pull"))
329 reg |= WDT_PUSH_PULL_MAGIC;
330 else
331 reg |= WDT_OPEN_DRAIN_MAGIC;
332
333 writel(reg, wdt->base + WDT_RESET_WIDTH);
334
335 reg &= config->ext_pulse_width_mask;
336 if (of_property_read_bool(np, "aspeed,ext-active-high"))
337 reg |= WDT_ACTIVE_HIGH_MAGIC;
338 else
339 reg |= WDT_ACTIVE_LOW_MAGIC;
340
341 writel(reg, wdt->base + WDT_RESET_WIDTH);
342 }
343
344 if (!of_property_read_u32(np, "aspeed,ext-pulse-duration", &duration)) {
345 u32 max_duration = config->ext_pulse_width_mask + 1;
346
347 if (duration == 0 || duration > max_duration) {
348 dev_err(dev, "Invalid pulse duration: %uus\n",
349 duration);
350 duration = max(1U, min(max_duration, duration));
351 dev_info(dev, "Pulse duration set to %uus\n",
352 duration);
353 }
354
355 /*
356 * The watchdog is always configured with a 1MHz source, so
357 * there is no need to scale the microsecond value. However we
358 * need to offset it - from the datasheet:
359 *
360 * "This register decides the asserting duration of wdt_ext and
361 * wdt_rstarm signal. The default value is 0xFF. It means the
362 * default asserting duration of wdt_ext and wdt_rstarm is
363 * 256us."
364 *
365 * This implies a value of 0 gives a 1us pulse.
366 */
367 writel(duration - 1, wdt->base + WDT_RESET_WIDTH);
368 }
369
370 status = readl(wdt->base + WDT_TIMEOUT_STATUS);
371 if (status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY) {
372 wdt->wdd.bootstatus = WDIOF_CARDRESET;
373
374 if (of_device_is_compatible(np, "aspeed,ast2400-wdt") ||
375 of_device_is_compatible(np, "aspeed,ast2500-wdt"))
376 wdt->wdd.groups = bswitch_groups;
377 }
378
379 dev_set_drvdata(dev, wdt);
380
381 return devm_watchdog_register_device(dev, &wdt->wdd);
382}
383
384static struct platform_driver aspeed_watchdog_driver = {
385 .probe = aspeed_wdt_probe,
386 .driver = {
387 .name = KBUILD_MODNAME,
388 .of_match_table = of_match_ptr(aspeed_wdt_of_table),
389 },
390};
391
392static int __init aspeed_wdt_init(void)
393{
394 return platform_driver_register(&aspeed_watchdog_driver);
395}
396arch_initcall(aspeed_wdt_init);
397
398static void __exit aspeed_wdt_exit(void)
399{
400 platform_driver_unregister(&aspeed_watchdog_driver);
401}
402module_exit(aspeed_wdt_exit);
403
404MODULE_DESCRIPTION("Aspeed Watchdog Driver");
405MODULE_LICENSE("GPL");
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * Copyright 2016 IBM Corporation
4 *
5 * Joel Stanley <joel@jms.id.au>
6 */
7
8#include <linux/bits.h>
9#include <linux/delay.h>
10#include <linux/interrupt.h>
11#include <linux/io.h>
12#include <linux/kernel.h>
13#include <linux/module.h>
14#include <linux/of.h>
15#include <linux/of_irq.h>
16#include <linux/platform_device.h>
17#include <linux/watchdog.h>
18
19static bool nowayout = WATCHDOG_NOWAYOUT;
20module_param(nowayout, bool, 0);
21MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default="
22 __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
23
24struct aspeed_wdt_config {
25 u32 ext_pulse_width_mask;
26 u32 irq_shift;
27 u32 irq_mask;
28};
29
30struct aspeed_wdt {
31 struct watchdog_device wdd;
32 void __iomem *base;
33 u32 ctrl;
34 const struct aspeed_wdt_config *cfg;
35};
36
37static const struct aspeed_wdt_config ast2400_config = {
38 .ext_pulse_width_mask = 0xff,
39 .irq_shift = 0,
40 .irq_mask = 0,
41};
42
43static const struct aspeed_wdt_config ast2500_config = {
44 .ext_pulse_width_mask = 0xfffff,
45 .irq_shift = 12,
46 .irq_mask = GENMASK(31, 12),
47};
48
49static const struct aspeed_wdt_config ast2600_config = {
50 .ext_pulse_width_mask = 0xfffff,
51 .irq_shift = 0,
52 .irq_mask = GENMASK(31, 10),
53};
54
55static const struct of_device_id aspeed_wdt_of_table[] = {
56 { .compatible = "aspeed,ast2400-wdt", .data = &ast2400_config },
57 { .compatible = "aspeed,ast2500-wdt", .data = &ast2500_config },
58 { .compatible = "aspeed,ast2600-wdt", .data = &ast2600_config },
59 { },
60};
61MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table);
62
63#define WDT_STATUS 0x00
64#define WDT_RELOAD_VALUE 0x04
65#define WDT_RESTART 0x08
66#define WDT_CTRL 0x0C
67#define WDT_CTRL_BOOT_SECONDARY BIT(7)
68#define WDT_CTRL_RESET_MODE_SOC (0x00 << 5)
69#define WDT_CTRL_RESET_MODE_FULL_CHIP (0x01 << 5)
70#define WDT_CTRL_RESET_MODE_ARM_CPU (0x10 << 5)
71#define WDT_CTRL_1MHZ_CLK BIT(4)
72#define WDT_CTRL_WDT_EXT BIT(3)
73#define WDT_CTRL_WDT_INTR BIT(2)
74#define WDT_CTRL_RESET_SYSTEM BIT(1)
75#define WDT_CTRL_ENABLE BIT(0)
76#define WDT_TIMEOUT_STATUS 0x10
77#define WDT_TIMEOUT_STATUS_IRQ BIT(2)
78#define WDT_TIMEOUT_STATUS_BOOT_SECONDARY BIT(1)
79#define WDT_CLEAR_TIMEOUT_STATUS 0x14
80#define WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION BIT(0)
81
82/*
83 * WDT_RESET_WIDTH controls the characteristics of the external pulse (if
84 * enabled), specifically:
85 *
86 * * Pulse duration
87 * * Drive mode: push-pull vs open-drain
88 * * Polarity: Active high or active low
89 *
90 * Pulse duration configuration is available on both the AST2400 and AST2500,
91 * though the field changes between SoCs:
92 *
93 * AST2400: Bits 7:0
94 * AST2500: Bits 19:0
95 *
96 * This difference is captured in struct aspeed_wdt_config.
97 *
98 * The AST2500 exposes the drive mode and polarity options, but not in a
99 * regular fashion. For read purposes, bit 31 represents active high or low,
100 * and bit 30 represents push-pull or open-drain. With respect to write, magic
101 * values need to be written to the top byte to change the state of the drive
102 * mode and polarity bits. Any other value written to the top byte has no
103 * effect on the state of the drive mode or polarity bits. However, the pulse
104 * width value must be preserved (as desired) if written.
105 */
106#define WDT_RESET_WIDTH 0x18
107#define WDT_RESET_WIDTH_ACTIVE_HIGH BIT(31)
108#define WDT_ACTIVE_HIGH_MAGIC (0xA5 << 24)
109#define WDT_ACTIVE_LOW_MAGIC (0x5A << 24)
110#define WDT_RESET_WIDTH_PUSH_PULL BIT(30)
111#define WDT_PUSH_PULL_MAGIC (0xA8 << 24)
112#define WDT_OPEN_DRAIN_MAGIC (0x8A << 24)
113
114#define WDT_RESTART_MAGIC 0x4755
115
116/* 32 bits at 1MHz, in milliseconds */
117#define WDT_MAX_TIMEOUT_MS 4294967
118#define WDT_DEFAULT_TIMEOUT 30
119#define WDT_RATE_1MHZ 1000000
120
121static struct aspeed_wdt *to_aspeed_wdt(struct watchdog_device *wdd)
122{
123 return container_of(wdd, struct aspeed_wdt, wdd);
124}
125
126static void aspeed_wdt_enable(struct aspeed_wdt *wdt, int count)
127{
128 wdt->ctrl |= WDT_CTRL_ENABLE;
129
130 writel(0, wdt->base + WDT_CTRL);
131 writel(count, wdt->base + WDT_RELOAD_VALUE);
132 writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART);
133 writel(wdt->ctrl, wdt->base + WDT_CTRL);
134}
135
136static int aspeed_wdt_start(struct watchdog_device *wdd)
137{
138 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
139
140 aspeed_wdt_enable(wdt, wdd->timeout * WDT_RATE_1MHZ);
141
142 return 0;
143}
144
145static int aspeed_wdt_stop(struct watchdog_device *wdd)
146{
147 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
148
149 wdt->ctrl &= ~WDT_CTRL_ENABLE;
150 writel(wdt->ctrl, wdt->base + WDT_CTRL);
151
152 return 0;
153}
154
155static int aspeed_wdt_ping(struct watchdog_device *wdd)
156{
157 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
158
159 writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART);
160
161 return 0;
162}
163
164static int aspeed_wdt_set_timeout(struct watchdog_device *wdd,
165 unsigned int timeout)
166{
167 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
168 u32 actual;
169
170 wdd->timeout = timeout;
171
172 actual = min(timeout, wdd->max_hw_heartbeat_ms / 1000);
173
174 writel(actual * WDT_RATE_1MHZ, wdt->base + WDT_RELOAD_VALUE);
175 writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART);
176
177 return 0;
178}
179
180static int aspeed_wdt_set_pretimeout(struct watchdog_device *wdd,
181 unsigned int pretimeout)
182{
183 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
184 u32 actual = pretimeout * WDT_RATE_1MHZ;
185 u32 s = wdt->cfg->irq_shift;
186 u32 m = wdt->cfg->irq_mask;
187
188 wdd->pretimeout = pretimeout;
189 wdt->ctrl &= ~m;
190 if (pretimeout)
191 wdt->ctrl |= ((actual << s) & m) | WDT_CTRL_WDT_INTR;
192 else
193 wdt->ctrl &= ~WDT_CTRL_WDT_INTR;
194
195 writel(wdt->ctrl, wdt->base + WDT_CTRL);
196
197 return 0;
198}
199
200static int aspeed_wdt_restart(struct watchdog_device *wdd,
201 unsigned long action, void *data)
202{
203 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
204
205 wdt->ctrl &= ~WDT_CTRL_BOOT_SECONDARY;
206 aspeed_wdt_enable(wdt, 128 * WDT_RATE_1MHZ / 1000);
207
208 mdelay(1000);
209
210 return 0;
211}
212
213/* access_cs0 shows if cs0 is accessible, hence the reverted bit */
214static ssize_t access_cs0_show(struct device *dev,
215 struct device_attribute *attr, char *buf)
216{
217 struct aspeed_wdt *wdt = dev_get_drvdata(dev);
218 u32 status = readl(wdt->base + WDT_TIMEOUT_STATUS);
219
220 return sysfs_emit(buf, "%u\n",
221 !(status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY));
222}
223
224static ssize_t access_cs0_store(struct device *dev,
225 struct device_attribute *attr, const char *buf,
226 size_t size)
227{
228 struct aspeed_wdt *wdt = dev_get_drvdata(dev);
229 unsigned long val;
230
231 if (kstrtoul(buf, 10, &val))
232 return -EINVAL;
233
234 if (val)
235 writel(WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION,
236 wdt->base + WDT_CLEAR_TIMEOUT_STATUS);
237
238 return size;
239}
240
241/*
242 * This attribute exists only if the system has booted from the alternate
243 * flash with 'alt-boot' option.
244 *
245 * At alternate flash the 'access_cs0' sysfs node provides:
246 * ast2400: a way to get access to the primary SPI flash chip at CS0
247 * after booting from the alternate chip at CS1.
248 * ast2500: a way to restore the normal address mapping from
249 * (CS0->CS1, CS1->CS0) to (CS0->CS0, CS1->CS1).
250 *
251 * Clearing the boot code selection and timeout counter also resets to the
252 * initial state the chip select line mapping. When the SoC is in normal
253 * mapping state (i.e. booted from CS0), clearing those bits does nothing for
254 * both versions of the SoC. For alternate boot mode (booted from CS1 due to
255 * wdt2 expiration) the behavior differs as described above.
256 *
257 * This option can be used with wdt2 (watchdog1) only.
258 */
259static DEVICE_ATTR_RW(access_cs0);
260
261static struct attribute *bswitch_attrs[] = {
262 &dev_attr_access_cs0.attr,
263 NULL
264};
265ATTRIBUTE_GROUPS(bswitch);
266
267static const struct watchdog_ops aspeed_wdt_ops = {
268 .start = aspeed_wdt_start,
269 .stop = aspeed_wdt_stop,
270 .ping = aspeed_wdt_ping,
271 .set_timeout = aspeed_wdt_set_timeout,
272 .set_pretimeout = aspeed_wdt_set_pretimeout,
273 .restart = aspeed_wdt_restart,
274 .owner = THIS_MODULE,
275};
276
277static const struct watchdog_info aspeed_wdt_info = {
278 .options = WDIOF_KEEPALIVEPING
279 | WDIOF_MAGICCLOSE
280 | WDIOF_SETTIMEOUT,
281 .identity = KBUILD_MODNAME,
282};
283
284static const struct watchdog_info aspeed_wdt_pretimeout_info = {
285 .options = WDIOF_KEEPALIVEPING
286 | WDIOF_PRETIMEOUT
287 | WDIOF_MAGICCLOSE
288 | WDIOF_SETTIMEOUT,
289 .identity = KBUILD_MODNAME,
290};
291
292static irqreturn_t aspeed_wdt_irq(int irq, void *arg)
293{
294 struct watchdog_device *wdd = arg;
295 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd);
296 u32 status = readl(wdt->base + WDT_TIMEOUT_STATUS);
297
298 if (status & WDT_TIMEOUT_STATUS_IRQ)
299 watchdog_notify_pretimeout(wdd);
300
301 return IRQ_HANDLED;
302}
303
304static int aspeed_wdt_probe(struct platform_device *pdev)
305{
306 struct device *dev = &pdev->dev;
307 const struct of_device_id *ofdid;
308 struct aspeed_wdt *wdt;
309 struct device_node *np;
310 const char *reset_type;
311 u32 duration;
312 u32 status;
313 int ret;
314
315 wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
316 if (!wdt)
317 return -ENOMEM;
318
319 np = dev->of_node;
320
321 ofdid = of_match_node(aspeed_wdt_of_table, np);
322 if (!ofdid)
323 return -EINVAL;
324 wdt->cfg = ofdid->data;
325
326 wdt->base = devm_platform_ioremap_resource(pdev, 0);
327 if (IS_ERR(wdt->base))
328 return PTR_ERR(wdt->base);
329
330 wdt->wdd.info = &aspeed_wdt_info;
331
332 if (wdt->cfg->irq_mask) {
333 int irq = platform_get_irq_optional(pdev, 0);
334
335 if (irq > 0) {
336 ret = devm_request_irq(dev, irq, aspeed_wdt_irq,
337 IRQF_SHARED, dev_name(dev),
338 wdt);
339 if (ret)
340 return ret;
341
342 wdt->wdd.info = &aspeed_wdt_pretimeout_info;
343 }
344 }
345
346 wdt->wdd.ops = &aspeed_wdt_ops;
347 wdt->wdd.max_hw_heartbeat_ms = WDT_MAX_TIMEOUT_MS;
348 wdt->wdd.parent = dev;
349
350 wdt->wdd.timeout = WDT_DEFAULT_TIMEOUT;
351 watchdog_init_timeout(&wdt->wdd, 0, dev);
352
353 watchdog_set_nowayout(&wdt->wdd, nowayout);
354
355 /*
356 * On clock rates:
357 * - ast2400 wdt can run at PCLK, or 1MHz
358 * - ast2500 only runs at 1MHz, hard coding bit 4 to 1
359 * - ast2600 always runs at 1MHz
360 *
361 * Set the ast2400 to run at 1MHz as it simplifies the driver.
362 */
363 if (of_device_is_compatible(np, "aspeed,ast2400-wdt"))
364 wdt->ctrl = WDT_CTRL_1MHZ_CLK;
365
366 /*
367 * Control reset on a per-device basis to ensure the
368 * host is not affected by a BMC reboot
369 */
370 ret = of_property_read_string(np, "aspeed,reset-type", &reset_type);
371 if (ret) {
372 wdt->ctrl |= WDT_CTRL_RESET_MODE_SOC | WDT_CTRL_RESET_SYSTEM;
373 } else {
374 if (!strcmp(reset_type, "cpu"))
375 wdt->ctrl |= WDT_CTRL_RESET_MODE_ARM_CPU |
376 WDT_CTRL_RESET_SYSTEM;
377 else if (!strcmp(reset_type, "soc"))
378 wdt->ctrl |= WDT_CTRL_RESET_MODE_SOC |
379 WDT_CTRL_RESET_SYSTEM;
380 else if (!strcmp(reset_type, "system"))
381 wdt->ctrl |= WDT_CTRL_RESET_MODE_FULL_CHIP |
382 WDT_CTRL_RESET_SYSTEM;
383 else if (strcmp(reset_type, "none"))
384 return -EINVAL;
385 }
386 if (of_property_read_bool(np, "aspeed,external-signal"))
387 wdt->ctrl |= WDT_CTRL_WDT_EXT;
388 if (of_property_read_bool(np, "aspeed,alt-boot"))
389 wdt->ctrl |= WDT_CTRL_BOOT_SECONDARY;
390
391 if (readl(wdt->base + WDT_CTRL) & WDT_CTRL_ENABLE) {
392 /*
393 * The watchdog is running, but invoke aspeed_wdt_start() to
394 * write wdt->ctrl to WDT_CTRL to ensure the watchdog's
395 * configuration conforms to the driver's expectations.
396 * Primarily, ensure we're using the 1MHz clock source.
397 */
398 aspeed_wdt_start(&wdt->wdd);
399 set_bit(WDOG_HW_RUNNING, &wdt->wdd.status);
400 }
401
402 if ((of_device_is_compatible(np, "aspeed,ast2500-wdt")) ||
403 (of_device_is_compatible(np, "aspeed,ast2600-wdt"))) {
404 u32 reg = readl(wdt->base + WDT_RESET_WIDTH);
405
406 reg &= wdt->cfg->ext_pulse_width_mask;
407 if (of_property_read_bool(np, "aspeed,ext-active-high"))
408 reg |= WDT_ACTIVE_HIGH_MAGIC;
409 else
410 reg |= WDT_ACTIVE_LOW_MAGIC;
411
412 writel(reg, wdt->base + WDT_RESET_WIDTH);
413
414 reg &= wdt->cfg->ext_pulse_width_mask;
415 if (of_property_read_bool(np, "aspeed,ext-push-pull"))
416 reg |= WDT_PUSH_PULL_MAGIC;
417 else
418 reg |= WDT_OPEN_DRAIN_MAGIC;
419
420 writel(reg, wdt->base + WDT_RESET_WIDTH);
421 }
422
423 if (!of_property_read_u32(np, "aspeed,ext-pulse-duration", &duration)) {
424 u32 max_duration = wdt->cfg->ext_pulse_width_mask + 1;
425
426 if (duration == 0 || duration > max_duration) {
427 dev_err(dev, "Invalid pulse duration: %uus\n",
428 duration);
429 duration = max(1U, min(max_duration, duration));
430 dev_info(dev, "Pulse duration set to %uus\n",
431 duration);
432 }
433
434 /*
435 * The watchdog is always configured with a 1MHz source, so
436 * there is no need to scale the microsecond value. However we
437 * need to offset it - from the datasheet:
438 *
439 * "This register decides the asserting duration of wdt_ext and
440 * wdt_rstarm signal. The default value is 0xFF. It means the
441 * default asserting duration of wdt_ext and wdt_rstarm is
442 * 256us."
443 *
444 * This implies a value of 0 gives a 1us pulse.
445 */
446 writel(duration - 1, wdt->base + WDT_RESET_WIDTH);
447 }
448
449 status = readl(wdt->base + WDT_TIMEOUT_STATUS);
450 if (status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY) {
451 wdt->wdd.bootstatus = WDIOF_CARDRESET;
452
453 if (of_device_is_compatible(np, "aspeed,ast2400-wdt") ||
454 of_device_is_compatible(np, "aspeed,ast2500-wdt"))
455 wdt->wdd.groups = bswitch_groups;
456 }
457
458 dev_set_drvdata(dev, wdt);
459
460 return devm_watchdog_register_device(dev, &wdt->wdd);
461}
462
463static struct platform_driver aspeed_watchdog_driver = {
464 .probe = aspeed_wdt_probe,
465 .driver = {
466 .name = KBUILD_MODNAME,
467 .of_match_table = of_match_ptr(aspeed_wdt_of_table),
468 },
469};
470
471static int __init aspeed_wdt_init(void)
472{
473 return platform_driver_register(&aspeed_watchdog_driver);
474}
475arch_initcall(aspeed_wdt_init);
476
477static void __exit aspeed_wdt_exit(void)
478{
479 platform_driver_unregister(&aspeed_watchdog_driver);
480}
481module_exit(aspeed_wdt_exit);
482
483MODULE_DESCRIPTION("Aspeed Watchdog Driver");
484MODULE_LICENSE("GPL");