1# SPDX-License-Identifier: GPL-2.0-only
  2menuconfig EXTCON
  3	tristate "External Connector Class (extcon) support"
  4	help
  5	  Say Y here to enable external connector class (extcon) support.
  6	  This allows monitoring external connectors by userspace
  7	  via sysfs and uevent and supports external connectors with
  8	  multiple states; i.e., an extcon that may have multiple
  9	  cables attached. For example, an external connector of a device
 10	  may be used to connect an HDMI cable and a AC adaptor, and to
 11	  host USB ports. Many of 30-pin connectors including PDMI are
 12	  also good examples.
 13
 14if EXTCON
 15
 16comment "Extcon Device Drivers"
 17
 18config EXTCON_ADC_JACK
 19	tristate "ADC Jack extcon support"
 20	depends on IIO
 21	help
 22	  Say Y here to enable extcon device driver based on ADC values.
 23
 24config EXTCON_ARIZONA
 25	tristate "Wolfson Arizona EXTCON support"
 26	depends on MFD_ARIZONA && INPUT && SND_SOC
 27	help
 28	  Say Y here to enable support for external accessory detection
 29	  with Wolfson Arizona devices. These are audio CODECs with
 30	  advanced audio accessory detection support.
 31
 32config EXTCON_AXP288
 33	tristate "X-Power AXP288 EXTCON support"
 34	depends on MFD_AXP20X && USB_SUPPORT && X86 && ACPI
 35	select USB_ROLE_SWITCH
 36	help
 37	  Say Y here to enable support for USB peripheral detection
 38	  and USB MUX switching by X-Power AXP288 PMIC.
 39
 40config EXTCON_FSA9480
 41	tristate "FSA9480 EXTCON Support"
 42	depends on INPUT && I2C
 43	select IRQ_DOMAIN
 44	select REGMAP_I2C
 45	help
 46	  If you say yes here you get support for the Fairchild Semiconductor
 47	  FSA9480 microUSB switch and accessory detector chip. The FSA9480 is a USB
 48	  port accessory detector and switch. The FSA9480 is fully controlled using
 49	  I2C and enables USB data, stereo and mono audio, video, microphone
 50	  and UART data to use a common connector port.
 51
 52config EXTCON_GPIO
 53	tristate "GPIO extcon support"
 54	depends on GPIOLIB || COMPILE_TEST
 55	help
 56	  Say Y here to enable GPIO based extcon support. Note that GPIO
 57	  extcon supports single state per extcon instance.
 58
 59config EXTCON_INTEL_INT3496
 60	tristate "Intel INT3496 ACPI device extcon driver"
 61	depends on GPIOLIB && ACPI && (X86 || COMPILE_TEST)
 62	help
 63	  Say Y here to enable extcon support for USB OTG ports controlled by
 64	  an Intel INT3496 ACPI device.
 65
 66	  This ACPI device is typically found on Intel Baytrail or Cherrytrail
 67	  based tablets, or other Baytrail / Cherrytrail devices.
 68
 69config EXTCON_INTEL_CHT_WC
 70	tristate "Intel Cherrytrail Whiskey Cove PMIC extcon driver"
 71	depends on INTEL_SOC_PMIC_CHTWC
 72	help
 73	  Say Y here to enable extcon support for charger detection / control
 74	  on the Intel Cherrytrail Whiskey Cove PMIC.
 75
 76config EXTCON_INTEL_MRFLD
 77	tristate "Intel Merrifield Basin Cove PMIC extcon driver"
 78	depends on INTEL_SOC_PMIC_MRFLD
 79	help
 80	  Say Y here to enable extcon support for charger detection / control
 81	  on the Intel Merrifield Basin Cove PMIC.
 82
 83config EXTCON_MAX14577
 84	tristate "Maxim MAX14577/77836 EXTCON Support"
 85	depends on MFD_MAX14577
 86	select IRQ_DOMAIN
 87	select REGMAP_I2C
 88	help
 89	  If you say yes here you get support for the MUIC device of
 90	  Maxim MAX14577/77836. The MAX14577/77836 MUIC is a USB port accessory
 91	  detector and switch.
 92
 93config EXTCON_MAX3355
 94	tristate "Maxim MAX3355 USB OTG EXTCON Support"
 95	depends on GPIOLIB || COMPILE_TEST
 96	help
 97	  If you say yes here you get support for the USB OTG role detection by
 98	  MAX3355. The MAX3355 chip integrates a charge pump and comparators to
 99	  enable a system with an integrated USB OTG dual-role transceiver to
100	  function as an USB OTG dual-role device.
101
102config EXTCON_MAX77693
103	tristate "Maxim MAX77693 EXTCON Support"
104	depends on MFD_MAX77693 && INPUT
105	select IRQ_DOMAIN
106	select REGMAP_I2C
107	help
108	  If you say yes here you get support for the MUIC device of
109	  Maxim MAX77693 PMIC. The MAX77693 MUIC is a USB port accessory
110	  detector and switch.
111
112config EXTCON_MAX77843
113	tristate "Maxim MAX77843 EXTCON Support"
114	depends on MFD_MAX77843
115	select IRQ_DOMAIN
116	select REGMAP_I2C
117	help
118	  If you say yes here you get support for the MUIC device of
119	  Maxim MAX77843. The MAX77843 MUIC is a USB port accessory
120	  detector add switch.
121
122config EXTCON_MAX8997
123	tristate "Maxim MAX8997 EXTCON Support"
124	depends on MFD_MAX8997 && IRQ_DOMAIN
125	help
126	  If you say yes here you get support for the MUIC device of
127	  Maxim MAX8997 PMIC. The MAX8997 MUIC is a USB port accessory
128	  detector and switch.
129
130config EXTCON_PALMAS
131	tristate "Palmas USB EXTCON support"
132	depends on MFD_PALMAS
133	help
134	  Say Y here to enable support for USB peripheral and USB host
135	  detection by palmas usb.
136
137config EXTCON_PTN5150
138	tristate "NXP PTN5150 CC LOGIC USB EXTCON support"
139	depends on I2C && (GPIOLIB || COMPILE_TEST)
140	select REGMAP_I2C
141	help
142	  Say Y here to enable support for USB peripheral and USB host
143	  detection by NXP PTN5150 CC (Configuration Channel) logic chip.
144
145config EXTCON_QCOM_SPMI_MISC
146	tristate "Qualcomm USB extcon support"
147	depends on ARCH_QCOM || COMPILE_TEST
148	help
149	  Say Y here to enable SPMI PMIC based USB cable detection
150	  support on Qualcomm PMICs such as PM8941.
151
152config EXTCON_RT8973A
153	tristate "Richtek RT8973A EXTCON support"
154	depends on I2C
155	select IRQ_DOMAIN
156	select REGMAP_I2C
157	select REGMAP_IRQ
158	help
159	  If you say yes here you get support for the MUIC device of
160	  Richtek RT8973A. The RT8973A is a USB port accessory detector
161	  and switch that is optimized to protect low voltage system
162	  from abnormal high input voltage (up to 28V).
163
164config EXTCON_SM5502
165	tristate "Silicon Mitus SM5502 EXTCON support"
166	depends on I2C
167	select IRQ_DOMAIN
168	select REGMAP_I2C
169	select REGMAP_IRQ
170	help
171	  If you say yes here you get support for the MUIC device of
172	  Silicon Mitus SM5502. The SM5502 is a USB port accessory
173	  detector and switch.
174
175config EXTCON_USB_GPIO
176	tristate "USB GPIO extcon support"
177	depends on GPIOLIB || COMPILE_TEST
178	help
179	  Say Y here to enable GPIO based USB cable detection extcon support.
180	  Used typically if GPIO is used for USB ID pin detection.
181
182config EXTCON_USBC_CROS_EC
183	tristate "ChromeOS Embedded Controller EXTCON support"
184	depends on CROS_EC
185	help
186	  Say Y here to enable USB Type C cable detection extcon support when
187	  using Chrome OS EC based USB Type-C ports.
 
 
 
 
 
 
 
 
188
189endif

  1# SPDX-License-Identifier: GPL-2.0-only
  2menuconfig EXTCON
  3	tristate "External Connector Class (extcon) support"
  4	help
  5	  Say Y here to enable external connector class (extcon) support.
  6	  This allows monitoring external connectors by userspace
  7	  via sysfs and uevent and supports external connectors with
  8	  multiple states; i.e., an extcon that may have multiple
  9	  cables attached. For example, an external connector of a device
 10	  may be used to connect an HDMI cable and a AC adaptor, and to
 11	  host USB ports. Many of 30-pin connectors including PDMI are
 12	  also good examples.
 13
 14if EXTCON
 15
 16comment "Extcon Device Drivers"
 17
 18config EXTCON_ADC_JACK
 19	tristate "ADC Jack extcon support"
 20	depends on IIO
 21	help
 22	  Say Y here to enable extcon device driver based on ADC values.
 23
 
 
 
 
 
 
 
 
 24config EXTCON_AXP288
 25	tristate "X-Power AXP288 EXTCON support"
 26	depends on MFD_AXP20X && USB_SUPPORT && X86 && ACPI
 27	select USB_ROLE_SWITCH
 28	help
 29	  Say Y here to enable support for USB peripheral detection
 30	  and USB MUX switching by X-Power AXP288 PMIC.
 31
 32config EXTCON_FSA9480
 33	tristate "FSA9480 EXTCON Support"
 34	depends on INPUT && I2C
 35	select IRQ_DOMAIN
 36	select REGMAP_I2C
 37	help
 38	  If you say yes here you get support for the Fairchild Semiconductor
 39	  FSA9480 microUSB switch and accessory detector chip. The FSA9480 is a USB
 40	  port accessory detector and switch. The FSA9480 is fully controlled using
 41	  I2C and enables USB data, stereo and mono audio, video, microphone
 42	  and UART data to use a common connector port.
 43
 44config EXTCON_GPIO
 45	tristate "GPIO extcon support"
 46	depends on GPIOLIB || COMPILE_TEST
 47	help
 48	  Say Y here to enable GPIO based extcon support. Note that GPIO
 49	  extcon supports single state per extcon instance.
 50
 51config EXTCON_INTEL_INT3496
 52	tristate "Intel INT3496 ACPI device extcon driver"
 53	depends on GPIOLIB && ACPI && (X86 || COMPILE_TEST)
 54	help
 55	  Say Y here to enable extcon support for USB OTG ports controlled by
 56	  an Intel INT3496 ACPI device.
 57
 58	  This ACPI device is typically found on Intel Baytrail or Cherrytrail
 59	  based tablets, or other Baytrail / Cherrytrail devices.
 60
 61config EXTCON_INTEL_CHT_WC
 62	tristate "Intel Cherrytrail Whiskey Cove PMIC extcon driver"
 63	depends on INTEL_SOC_PMIC_CHTWC
 64	help
 65	  Say Y here to enable extcon support for charger detection / control
 66	  on the Intel Cherrytrail Whiskey Cove PMIC.
 67
 68config EXTCON_INTEL_MRFLD
 69	tristate "Intel Merrifield Basin Cove PMIC extcon driver"
 70	depends on INTEL_SOC_PMIC_MRFLD
 71	help
 72	  Say Y here to enable extcon support for charger detection / control
 73	  on the Intel Merrifield Basin Cove PMIC.
 74
 75config EXTCON_MAX14577
 76	tristate "Maxim MAX14577/77836 EXTCON Support"
 77	depends on MFD_MAX14577
 78	select IRQ_DOMAIN
 79	select REGMAP_I2C
 80	help
 81	  If you say yes here you get support for the MUIC device of
 82	  Maxim MAX14577/77836. The MAX14577/77836 MUIC is a USB port accessory
 83	  detector and switch.
 84
 85config EXTCON_MAX3355
 86	tristate "Maxim MAX3355 USB OTG EXTCON Support"
 87	depends on GPIOLIB || COMPILE_TEST
 88	help
 89	  If you say yes here you get support for the USB OTG role detection by
 90	  MAX3355. The MAX3355 chip integrates a charge pump and comparators to
 91	  enable a system with an integrated USB OTG dual-role transceiver to
 92	  function as an USB OTG dual-role device.
 93
 94config EXTCON_MAX77693
 95	tristate "Maxim MAX77693 EXTCON Support"
 96	depends on MFD_MAX77693 && INPUT
 97	select IRQ_DOMAIN
 98	select REGMAP_I2C
 99	help
100	  If you say yes here you get support for the MUIC device of
101	  Maxim MAX77693 PMIC. The MAX77693 MUIC is a USB port accessory
102	  detector and switch.
103
104config EXTCON_MAX77843
105	tristate "Maxim MAX77843 EXTCON Support"
106	depends on MFD_MAX77843
107	select IRQ_DOMAIN
108	select REGMAP_I2C
109	help
110	  If you say yes here you get support for the MUIC device of
111	  Maxim MAX77843. The MAX77843 MUIC is a USB port accessory
112	  detector add switch.
113
114config EXTCON_MAX8997
115	tristate "Maxim MAX8997 EXTCON Support"
116	depends on MFD_MAX8997 && IRQ_DOMAIN
117	help
118	  If you say yes here you get support for the MUIC device of
119	  Maxim MAX8997 PMIC. The MAX8997 MUIC is a USB port accessory
120	  detector and switch.
121
122config EXTCON_PALMAS
123	tristate "Palmas USB EXTCON support"
124	depends on MFD_PALMAS
125	help
126	  Say Y here to enable support for USB peripheral and USB host
127	  detection by palmas usb.
128
129config EXTCON_PTN5150
130	tristate "NXP PTN5150 CC LOGIC USB EXTCON support"
131	depends on I2C && (GPIOLIB || COMPILE_TEST)
132	select REGMAP_I2C
133	help
134	  Say Y here to enable support for USB peripheral and USB host
135	  detection by NXP PTN5150 CC (Configuration Channel) logic chip.
136
137config EXTCON_QCOM_SPMI_MISC
138	tristate "Qualcomm USB extcon support"
139	depends on ARCH_QCOM || COMPILE_TEST
140	help
141	  Say Y here to enable SPMI PMIC based USB cable detection
142	  support on Qualcomm PMICs such as PM8941.
143
144config EXTCON_RT8973A
145	tristate "Richtek RT8973A EXTCON support"
146	depends on I2C
147	select IRQ_DOMAIN
148	select REGMAP_I2C
149	select REGMAP_IRQ
150	help
151	  If you say yes here you get support for the MUIC device of
152	  Richtek RT8973A. The RT8973A is a USB port accessory detector
153	  and switch that is optimized to protect low voltage system
154	  from abnormal high input voltage (up to 28V).
155
156config EXTCON_SM5502
157	tristate "Silicon Mitus SM5502/SM5504 EXTCON support"
158	depends on I2C
159	select IRQ_DOMAIN
160	select REGMAP_I2C
161	select REGMAP_IRQ
162	help
163	  If you say yes here you get support for the MUIC device of
164	  Silicon Mitus SM5502. The SM5502 is a USB port accessory
165	  detector and switch.
166
167config EXTCON_USB_GPIO
168	tristate "USB GPIO extcon support"
169	depends on GPIOLIB || COMPILE_TEST
170	help
171	  Say Y here to enable GPIO based USB cable detection extcon support.
172	  Used typically if GPIO is used for USB ID pin detection.
173
174config EXTCON_USBC_CROS_EC
175	tristate "ChromeOS Embedded Controller EXTCON support"
176	depends on CROS_EC
177	help
178	  Say Y here to enable USB Type C cable detection extcon support when
179	  using Chrome OS EC based USB Type-C ports.
180
181config EXTCON_USBC_TUSB320
182	tristate "TI TUSB320 USB-C extcon support"
183	depends on I2C
184	select REGMAP_I2C
185	help
186	  Say Y here to enable support for USB Type C cable detection extcon
187	  support using a TUSB320.
188
189endif