Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * asb100.c - Part of lm_sensors, Linux kernel modules for hardware
4 * monitoring
5 *
6 * Copyright (C) 2004 Mark M. Hoffman <mhoffman@lightlink.com>
7 *
8 * (derived from w83781d.c)
9 *
10 * Copyright (C) 1998 - 2003 Frodo Looijaard <frodol@dds.nl>,
11 * Philip Edelbrock <phil@netroedge.com>, and
12 * Mark Studebaker <mdsxyz123@yahoo.com>
13 */
14
15/*
16 * This driver supports the hardware sensor chips: Asus ASB100 and
17 * ASB100-A "BACH".
18 *
19 * ASB100-A supports pwm1, while plain ASB100 does not. There is no known
20 * way for the driver to tell which one is there.
21 *
22 * Chip #vin #fanin #pwm #temp wchipid vendid i2c ISA
23 * asb100 7 3 1 4 0x31 0x0694 yes no
24 */
25
26#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
27
28#include <linux/module.h>
29#include <linux/slab.h>
30#include <linux/i2c.h>
31#include <linux/hwmon.h>
32#include <linux/hwmon-sysfs.h>
33#include <linux/hwmon-vid.h>
34#include <linux/err.h>
35#include <linux/init.h>
36#include <linux/jiffies.h>
37#include <linux/mutex.h>
38#include "lm75.h"
39
40/* I2C addresses to scan */
41static const unsigned short normal_i2c[] = { 0x2d, I2C_CLIENT_END };
42
43static unsigned short force_subclients[4];
44module_param_array(force_subclients, short, NULL, 0);
45MODULE_PARM_DESC(force_subclients,
46 "List of subclient addresses: {bus, clientaddr, subclientaddr1, subclientaddr2}");
47
48/* Voltage IN registers 0-6 */
49#define ASB100_REG_IN(nr) (0x20 + (nr))
50#define ASB100_REG_IN_MAX(nr) (0x2b + (nr * 2))
51#define ASB100_REG_IN_MIN(nr) (0x2c + (nr * 2))
52
53/* FAN IN registers 1-3 */
54#define ASB100_REG_FAN(nr) (0x28 + (nr))
55#define ASB100_REG_FAN_MIN(nr) (0x3b + (nr))
56
57/* TEMPERATURE registers 1-4 */
58static const u16 asb100_reg_temp[] = {0, 0x27, 0x150, 0x250, 0x17};
59static const u16 asb100_reg_temp_max[] = {0, 0x39, 0x155, 0x255, 0x18};
60static const u16 asb100_reg_temp_hyst[] = {0, 0x3a, 0x153, 0x253, 0x19};
61
62#define ASB100_REG_TEMP(nr) (asb100_reg_temp[nr])
63#define ASB100_REG_TEMP_MAX(nr) (asb100_reg_temp_max[nr])
64#define ASB100_REG_TEMP_HYST(nr) (asb100_reg_temp_hyst[nr])
65
66#define ASB100_REG_TEMP2_CONFIG 0x0152
67#define ASB100_REG_TEMP3_CONFIG 0x0252
68
69
70#define ASB100_REG_CONFIG 0x40
71#define ASB100_REG_ALARM1 0x41
72#define ASB100_REG_ALARM2 0x42
73#define ASB100_REG_SMIM1 0x43
74#define ASB100_REG_SMIM2 0x44
75#define ASB100_REG_VID_FANDIV 0x47
76#define ASB100_REG_I2C_ADDR 0x48
77#define ASB100_REG_CHIPID 0x49
78#define ASB100_REG_I2C_SUBADDR 0x4a
79#define ASB100_REG_PIN 0x4b
80#define ASB100_REG_IRQ 0x4c
81#define ASB100_REG_BANK 0x4e
82#define ASB100_REG_CHIPMAN 0x4f
83
84#define ASB100_REG_WCHIPID 0x58
85
86/* bit 7 -> enable, bits 0-3 -> duty cycle */
87#define ASB100_REG_PWM1 0x59
88
89/*
90 * CONVERSIONS
91 * Rounding and limit checking is only done on the TO_REG variants.
92 */
93
94/* These constants are a guess, consistent w/ w83781d */
95#define ASB100_IN_MIN 0
96#define ASB100_IN_MAX 4080
97
98/*
99 * IN: 1/1000 V (0V to 4.08V)
100 * REG: 16mV/bit
101 */
102static u8 IN_TO_REG(unsigned val)
103{
104 unsigned nval = clamp_val(val, ASB100_IN_MIN, ASB100_IN_MAX);
105 return (nval + 8) / 16;
106}
107
108static unsigned IN_FROM_REG(u8 reg)
109{
110 return reg * 16;
111}
112
113static u8 FAN_TO_REG(long rpm, int div)
114{
115 if (rpm == -1)
116 return 0;
117 if (rpm == 0)
118 return 255;
119 rpm = clamp_val(rpm, 1, 1000000);
120 return clamp_val((1350000 + rpm * div / 2) / (rpm * div), 1, 254);
121}
122
123static int FAN_FROM_REG(u8 val, int div)
124{
125 return val == 0 ? -1 : val == 255 ? 0 : 1350000 / (val * div);
126}
127
128/* These constants are a guess, consistent w/ w83781d */
129#define ASB100_TEMP_MIN -128000
130#define ASB100_TEMP_MAX 127000
131
132/*
133 * TEMP: 0.001C/bit (-128C to +127C)
134 * REG: 1C/bit, two's complement
135 */
136static u8 TEMP_TO_REG(long temp)
137{
138 int ntemp = clamp_val(temp, ASB100_TEMP_MIN, ASB100_TEMP_MAX);
139 ntemp += (ntemp < 0 ? -500 : 500);
140 return (u8)(ntemp / 1000);
141}
142
143static int TEMP_FROM_REG(u8 reg)
144{
145 return (s8)reg * 1000;
146}
147
148/*
149 * PWM: 0 - 255 per sensors documentation
150 * REG: (6.25% duty cycle per bit)
151 */
152static u8 ASB100_PWM_TO_REG(int pwm)
153{
154 pwm = clamp_val(pwm, 0, 255);
155 return (u8)(pwm / 16);
156}
157
158static int ASB100_PWM_FROM_REG(u8 reg)
159{
160 return reg * 16;
161}
162
163#define DIV_FROM_REG(val) (1 << (val))
164
165/*
166 * FAN DIV: 1, 2, 4, or 8 (defaults to 2)
167 * REG: 0, 1, 2, or 3 (respectively) (defaults to 1)
168 */
169static u8 DIV_TO_REG(long val)
170{
171 return val == 8 ? 3 : val == 4 ? 2 : val == 1 ? 0 : 1;
172}
173
174/*
175 * For each registered client, we need to keep some data in memory. That
176 * data is pointed to by client->data. The structure itself is
177 * dynamically allocated, at the same time the client itself is allocated.
178 */
179struct asb100_data {
180 struct device *hwmon_dev;
181 struct mutex lock;
182
183 struct mutex update_lock;
184 unsigned long last_updated; /* In jiffies */
185
186 /* array of 2 pointers to subclients */
187 struct i2c_client *lm75[2];
188
189 char valid; /* !=0 if following fields are valid */
190 u8 in[7]; /* Register value */
191 u8 in_max[7]; /* Register value */
192 u8 in_min[7]; /* Register value */
193 u8 fan[3]; /* Register value */
194 u8 fan_min[3]; /* Register value */
195 u16 temp[4]; /* Register value (0 and 3 are u8 only) */
196 u16 temp_max[4]; /* Register value (0 and 3 are u8 only) */
197 u16 temp_hyst[4]; /* Register value (0 and 3 are u8 only) */
198 u8 fan_div[3]; /* Register encoding, right justified */
199 u8 pwm; /* Register encoding */
200 u8 vid; /* Register encoding, combined */
201 u32 alarms; /* Register encoding, combined */
202 u8 vrm;
203};
204
205static int asb100_read_value(struct i2c_client *client, u16 reg);
206static void asb100_write_value(struct i2c_client *client, u16 reg, u16 val);
207
208static int asb100_probe(struct i2c_client *client,
209 const struct i2c_device_id *id);
210static int asb100_detect(struct i2c_client *client,
211 struct i2c_board_info *info);
212static int asb100_remove(struct i2c_client *client);
213static struct asb100_data *asb100_update_device(struct device *dev);
214static void asb100_init_client(struct i2c_client *client);
215
216static const struct i2c_device_id asb100_id[] = {
217 { "asb100", 0 },
218 { }
219};
220MODULE_DEVICE_TABLE(i2c, asb100_id);
221
222static struct i2c_driver asb100_driver = {
223 .class = I2C_CLASS_HWMON,
224 .driver = {
225 .name = "asb100",
226 },
227 .probe = asb100_probe,
228 .remove = asb100_remove,
229 .id_table = asb100_id,
230 .detect = asb100_detect,
231 .address_list = normal_i2c,
232};
233
234/* 7 Voltages */
235#define show_in_reg(reg) \
236static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \
237 char *buf) \
238{ \
239 int nr = to_sensor_dev_attr(attr)->index; \
240 struct asb100_data *data = asb100_update_device(dev); \
241 return sprintf(buf, "%d\n", IN_FROM_REG(data->reg[nr])); \
242}
243
244show_in_reg(in)
245show_in_reg(in_min)
246show_in_reg(in_max)
247
248#define set_in_reg(REG, reg) \
249static ssize_t set_in_##reg(struct device *dev, struct device_attribute *attr, \
250 const char *buf, size_t count) \
251{ \
252 int nr = to_sensor_dev_attr(attr)->index; \
253 struct i2c_client *client = to_i2c_client(dev); \
254 struct asb100_data *data = i2c_get_clientdata(client); \
255 unsigned long val; \
256 int err = kstrtoul(buf, 10, &val); \
257 if (err) \
258 return err; \
259 mutex_lock(&data->update_lock); \
260 data->in_##reg[nr] = IN_TO_REG(val); \
261 asb100_write_value(client, ASB100_REG_IN_##REG(nr), \
262 data->in_##reg[nr]); \
263 mutex_unlock(&data->update_lock); \
264 return count; \
265}
266
267set_in_reg(MIN, min)
268set_in_reg(MAX, max)
269
270#define sysfs_in(offset) \
271static SENSOR_DEVICE_ATTR(in##offset##_input, S_IRUGO, \
272 show_in, NULL, offset); \
273static SENSOR_DEVICE_ATTR(in##offset##_min, S_IRUGO | S_IWUSR, \
274 show_in_min, set_in_min, offset); \
275static SENSOR_DEVICE_ATTR(in##offset##_max, S_IRUGO | S_IWUSR, \
276 show_in_max, set_in_max, offset)
277
278sysfs_in(0);
279sysfs_in(1);
280sysfs_in(2);
281sysfs_in(3);
282sysfs_in(4);
283sysfs_in(5);
284sysfs_in(6);
285
286/* 3 Fans */
287static ssize_t show_fan(struct device *dev, struct device_attribute *attr,
288 char *buf)
289{
290 int nr = to_sensor_dev_attr(attr)->index;
291 struct asb100_data *data = asb100_update_device(dev);
292 return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan[nr],
293 DIV_FROM_REG(data->fan_div[nr])));
294}
295
296static ssize_t show_fan_min(struct device *dev, struct device_attribute *attr,
297 char *buf)
298{
299 int nr = to_sensor_dev_attr(attr)->index;
300 struct asb100_data *data = asb100_update_device(dev);
301 return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan_min[nr],
302 DIV_FROM_REG(data->fan_div[nr])));
303}
304
305static ssize_t show_fan_div(struct device *dev, struct device_attribute *attr,
306 char *buf)
307{
308 int nr = to_sensor_dev_attr(attr)->index;
309 struct asb100_data *data = asb100_update_device(dev);
310 return sprintf(buf, "%d\n", DIV_FROM_REG(data->fan_div[nr]));
311}
312
313static ssize_t set_fan_min(struct device *dev, struct device_attribute *attr,
314 const char *buf, size_t count)
315{
316 int nr = to_sensor_dev_attr(attr)->index;
317 struct i2c_client *client = to_i2c_client(dev);
318 struct asb100_data *data = i2c_get_clientdata(client);
319 unsigned long val;
320 int err;
321
322 err = kstrtoul(buf, 10, &val);
323 if (err)
324 return err;
325
326 mutex_lock(&data->update_lock);
327 data->fan_min[nr] = FAN_TO_REG(val, DIV_FROM_REG(data->fan_div[nr]));
328 asb100_write_value(client, ASB100_REG_FAN_MIN(nr), data->fan_min[nr]);
329 mutex_unlock(&data->update_lock);
330 return count;
331}
332
333/*
334 * Note: we save and restore the fan minimum here, because its value is
335 * determined in part by the fan divisor. This follows the principle of
336 * least surprise; the user doesn't expect the fan minimum to change just
337 * because the divisor changed.
338 */
339static ssize_t set_fan_div(struct device *dev, struct device_attribute *attr,
340 const char *buf, size_t count)
341{
342 int nr = to_sensor_dev_attr(attr)->index;
343 struct i2c_client *client = to_i2c_client(dev);
344 struct asb100_data *data = i2c_get_clientdata(client);
345 unsigned long min;
346 int reg;
347 unsigned long val;
348 int err;
349
350 err = kstrtoul(buf, 10, &val);
351 if (err)
352 return err;
353
354 mutex_lock(&data->update_lock);
355
356 min = FAN_FROM_REG(data->fan_min[nr],
357 DIV_FROM_REG(data->fan_div[nr]));
358 data->fan_div[nr] = DIV_TO_REG(val);
359
360 switch (nr) {
361 case 0: /* fan 1 */
362 reg = asb100_read_value(client, ASB100_REG_VID_FANDIV);
363 reg = (reg & 0xcf) | (data->fan_div[0] << 4);
364 asb100_write_value(client, ASB100_REG_VID_FANDIV, reg);
365 break;
366
367 case 1: /* fan 2 */
368 reg = asb100_read_value(client, ASB100_REG_VID_FANDIV);
369 reg = (reg & 0x3f) | (data->fan_div[1] << 6);
370 asb100_write_value(client, ASB100_REG_VID_FANDIV, reg);
371 break;
372
373 case 2: /* fan 3 */
374 reg = asb100_read_value(client, ASB100_REG_PIN);
375 reg = (reg & 0x3f) | (data->fan_div[2] << 6);
376 asb100_write_value(client, ASB100_REG_PIN, reg);
377 break;
378 }
379
380 data->fan_min[nr] =
381 FAN_TO_REG(min, DIV_FROM_REG(data->fan_div[nr]));
382 asb100_write_value(client, ASB100_REG_FAN_MIN(nr), data->fan_min[nr]);
383
384 mutex_unlock(&data->update_lock);
385
386 return count;
387}
388
389#define sysfs_fan(offset) \
390static SENSOR_DEVICE_ATTR(fan##offset##_input, S_IRUGO, \
391 show_fan, NULL, offset - 1); \
392static SENSOR_DEVICE_ATTR(fan##offset##_min, S_IRUGO | S_IWUSR, \
393 show_fan_min, set_fan_min, offset - 1); \
394static SENSOR_DEVICE_ATTR(fan##offset##_div, S_IRUGO | S_IWUSR, \
395 show_fan_div, set_fan_div, offset - 1)
396
397sysfs_fan(1);
398sysfs_fan(2);
399sysfs_fan(3);
400
401/* 4 Temp. Sensors */
402static int sprintf_temp_from_reg(u16 reg, char *buf, int nr)
403{
404 int ret = 0;
405
406 switch (nr) {
407 case 1: case 2:
408 ret = sprintf(buf, "%d\n", LM75_TEMP_FROM_REG(reg));
409 break;
410 case 0: case 3: default:
411 ret = sprintf(buf, "%d\n", TEMP_FROM_REG(reg));
412 break;
413 }
414 return ret;
415}
416
417#define show_temp_reg(reg) \
418static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \
419 char *buf) \
420{ \
421 int nr = to_sensor_dev_attr(attr)->index; \
422 struct asb100_data *data = asb100_update_device(dev); \
423 return sprintf_temp_from_reg(data->reg[nr], buf, nr); \
424}
425
426show_temp_reg(temp);
427show_temp_reg(temp_max);
428show_temp_reg(temp_hyst);
429
430#define set_temp_reg(REG, reg) \
431static ssize_t set_##reg(struct device *dev, struct device_attribute *attr, \
432 const char *buf, size_t count) \
433{ \
434 int nr = to_sensor_dev_attr(attr)->index; \
435 struct i2c_client *client = to_i2c_client(dev); \
436 struct asb100_data *data = i2c_get_clientdata(client); \
437 long val; \
438 int err = kstrtol(buf, 10, &val); \
439 if (err) \
440 return err; \
441 mutex_lock(&data->update_lock); \
442 switch (nr) { \
443 case 1: case 2: \
444 data->reg[nr] = LM75_TEMP_TO_REG(val); \
445 break; \
446 case 0: case 3: default: \
447 data->reg[nr] = TEMP_TO_REG(val); \
448 break; \
449 } \
450 asb100_write_value(client, ASB100_REG_TEMP_##REG(nr+1), \
451 data->reg[nr]); \
452 mutex_unlock(&data->update_lock); \
453 return count; \
454}
455
456set_temp_reg(MAX, temp_max);
457set_temp_reg(HYST, temp_hyst);
458
459#define sysfs_temp(num) \
460static SENSOR_DEVICE_ATTR(temp##num##_input, S_IRUGO, \
461 show_temp, NULL, num - 1); \
462static SENSOR_DEVICE_ATTR(temp##num##_max, S_IRUGO | S_IWUSR, \
463 show_temp_max, set_temp_max, num - 1); \
464static SENSOR_DEVICE_ATTR(temp##num##_max_hyst, S_IRUGO | S_IWUSR, \
465 show_temp_hyst, set_temp_hyst, num - 1)
466
467sysfs_temp(1);
468sysfs_temp(2);
469sysfs_temp(3);
470sysfs_temp(4);
471
472/* VID */
473static ssize_t cpu0_vid_show(struct device *dev,
474 struct device_attribute *attr, char *buf)
475{
476 struct asb100_data *data = asb100_update_device(dev);
477 return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm));
478}
479
480static DEVICE_ATTR_RO(cpu0_vid);
481
482/* VRM */
483static ssize_t vrm_show(struct device *dev, struct device_attribute *attr,
484 char *buf)
485{
486 struct asb100_data *data = dev_get_drvdata(dev);
487 return sprintf(buf, "%d\n", data->vrm);
488}
489
490static ssize_t vrm_store(struct device *dev, struct device_attribute *attr,
491 const char *buf, size_t count)
492{
493 struct asb100_data *data = dev_get_drvdata(dev);
494 unsigned long val;
495 int err;
496
497 err = kstrtoul(buf, 10, &val);
498 if (err)
499 return err;
500
501 if (val > 255)
502 return -EINVAL;
503
504 data->vrm = val;
505 return count;
506}
507
508/* Alarms */
509static DEVICE_ATTR_RW(vrm);
510
511static ssize_t alarms_show(struct device *dev, struct device_attribute *attr,
512 char *buf)
513{
514 struct asb100_data *data = asb100_update_device(dev);
515 return sprintf(buf, "%u\n", data->alarms);
516}
517
518static DEVICE_ATTR_RO(alarms);
519
520static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
521 char *buf)
522{
523 int bitnr = to_sensor_dev_attr(attr)->index;
524 struct asb100_data *data = asb100_update_device(dev);
525 return sprintf(buf, "%u\n", (data->alarms >> bitnr) & 1);
526}
527static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0);
528static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 1);
529static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 2);
530static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 3);
531static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 8);
532static SENSOR_DEVICE_ATTR(fan1_alarm, S_IRUGO, show_alarm, NULL, 6);
533static SENSOR_DEVICE_ATTR(fan2_alarm, S_IRUGO, show_alarm, NULL, 7);
534static SENSOR_DEVICE_ATTR(fan3_alarm, S_IRUGO, show_alarm, NULL, 11);
535static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 4);
536static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 5);
537static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 13);
538
539/* 1 PWM */
540static ssize_t pwm1_show(struct device *dev, struct device_attribute *attr,
541 char *buf)
542{
543 struct asb100_data *data = asb100_update_device(dev);
544 return sprintf(buf, "%d\n", ASB100_PWM_FROM_REG(data->pwm & 0x0f));
545}
546
547static ssize_t pwm1_store(struct device *dev, struct device_attribute *attr,
548 const char *buf, size_t count)
549{
550 struct i2c_client *client = to_i2c_client(dev);
551 struct asb100_data *data = i2c_get_clientdata(client);
552 unsigned long val;
553 int err;
554
555 err = kstrtoul(buf, 10, &val);
556 if (err)
557 return err;
558
559 mutex_lock(&data->update_lock);
560 data->pwm &= 0x80; /* keep the enable bit */
561 data->pwm |= (0x0f & ASB100_PWM_TO_REG(val));
562 asb100_write_value(client, ASB100_REG_PWM1, data->pwm);
563 mutex_unlock(&data->update_lock);
564 return count;
565}
566
567static ssize_t pwm1_enable_show(struct device *dev,
568 struct device_attribute *attr, char *buf)
569{
570 struct asb100_data *data = asb100_update_device(dev);
571 return sprintf(buf, "%d\n", (data->pwm & 0x80) ? 1 : 0);
572}
573
574static ssize_t pwm1_enable_store(struct device *dev,
575 struct device_attribute *attr,
576 const char *buf, size_t count)
577{
578 struct i2c_client *client = to_i2c_client(dev);
579 struct asb100_data *data = i2c_get_clientdata(client);
580 unsigned long val;
581 int err;
582
583 err = kstrtoul(buf, 10, &val);
584 if (err)
585 return err;
586
587 mutex_lock(&data->update_lock);
588 data->pwm &= 0x0f; /* keep the duty cycle bits */
589 data->pwm |= (val ? 0x80 : 0x00);
590 asb100_write_value(client, ASB100_REG_PWM1, data->pwm);
591 mutex_unlock(&data->update_lock);
592 return count;
593}
594
595static DEVICE_ATTR_RW(pwm1);
596static DEVICE_ATTR_RW(pwm1_enable);
597
598static struct attribute *asb100_attributes[] = {
599 &sensor_dev_attr_in0_input.dev_attr.attr,
600 &sensor_dev_attr_in0_min.dev_attr.attr,
601 &sensor_dev_attr_in0_max.dev_attr.attr,
602 &sensor_dev_attr_in1_input.dev_attr.attr,
603 &sensor_dev_attr_in1_min.dev_attr.attr,
604 &sensor_dev_attr_in1_max.dev_attr.attr,
605 &sensor_dev_attr_in2_input.dev_attr.attr,
606 &sensor_dev_attr_in2_min.dev_attr.attr,
607 &sensor_dev_attr_in2_max.dev_attr.attr,
608 &sensor_dev_attr_in3_input.dev_attr.attr,
609 &sensor_dev_attr_in3_min.dev_attr.attr,
610 &sensor_dev_attr_in3_max.dev_attr.attr,
611 &sensor_dev_attr_in4_input.dev_attr.attr,
612 &sensor_dev_attr_in4_min.dev_attr.attr,
613 &sensor_dev_attr_in4_max.dev_attr.attr,
614 &sensor_dev_attr_in5_input.dev_attr.attr,
615 &sensor_dev_attr_in5_min.dev_attr.attr,
616 &sensor_dev_attr_in5_max.dev_attr.attr,
617 &sensor_dev_attr_in6_input.dev_attr.attr,
618 &sensor_dev_attr_in6_min.dev_attr.attr,
619 &sensor_dev_attr_in6_max.dev_attr.attr,
620
621 &sensor_dev_attr_fan1_input.dev_attr.attr,
622 &sensor_dev_attr_fan1_min.dev_attr.attr,
623 &sensor_dev_attr_fan1_div.dev_attr.attr,
624 &sensor_dev_attr_fan2_input.dev_attr.attr,
625 &sensor_dev_attr_fan2_min.dev_attr.attr,
626 &sensor_dev_attr_fan2_div.dev_attr.attr,
627 &sensor_dev_attr_fan3_input.dev_attr.attr,
628 &sensor_dev_attr_fan3_min.dev_attr.attr,
629 &sensor_dev_attr_fan3_div.dev_attr.attr,
630
631 &sensor_dev_attr_temp1_input.dev_attr.attr,
632 &sensor_dev_attr_temp1_max.dev_attr.attr,
633 &sensor_dev_attr_temp1_max_hyst.dev_attr.attr,
634 &sensor_dev_attr_temp2_input.dev_attr.attr,
635 &sensor_dev_attr_temp2_max.dev_attr.attr,
636 &sensor_dev_attr_temp2_max_hyst.dev_attr.attr,
637 &sensor_dev_attr_temp3_input.dev_attr.attr,
638 &sensor_dev_attr_temp3_max.dev_attr.attr,
639 &sensor_dev_attr_temp3_max_hyst.dev_attr.attr,
640 &sensor_dev_attr_temp4_input.dev_attr.attr,
641 &sensor_dev_attr_temp4_max.dev_attr.attr,
642 &sensor_dev_attr_temp4_max_hyst.dev_attr.attr,
643
644 &sensor_dev_attr_in0_alarm.dev_attr.attr,
645 &sensor_dev_attr_in1_alarm.dev_attr.attr,
646 &sensor_dev_attr_in2_alarm.dev_attr.attr,
647 &sensor_dev_attr_in3_alarm.dev_attr.attr,
648 &sensor_dev_attr_in4_alarm.dev_attr.attr,
649 &sensor_dev_attr_fan1_alarm.dev_attr.attr,
650 &sensor_dev_attr_fan2_alarm.dev_attr.attr,
651 &sensor_dev_attr_fan3_alarm.dev_attr.attr,
652 &sensor_dev_attr_temp1_alarm.dev_attr.attr,
653 &sensor_dev_attr_temp2_alarm.dev_attr.attr,
654 &sensor_dev_attr_temp3_alarm.dev_attr.attr,
655
656 &dev_attr_cpu0_vid.attr,
657 &dev_attr_vrm.attr,
658 &dev_attr_alarms.attr,
659 &dev_attr_pwm1.attr,
660 &dev_attr_pwm1_enable.attr,
661
662 NULL
663};
664
665static const struct attribute_group asb100_group = {
666 .attrs = asb100_attributes,
667};
668
669static int asb100_detect_subclients(struct i2c_client *client)
670{
671 int i, id, err;
672 int address = client->addr;
673 unsigned short sc_addr[2];
674 struct asb100_data *data = i2c_get_clientdata(client);
675 struct i2c_adapter *adapter = client->adapter;
676
677 id = i2c_adapter_id(adapter);
678
679 if (force_subclients[0] == id && force_subclients[1] == address) {
680 for (i = 2; i <= 3; i++) {
681 if (force_subclients[i] < 0x48 ||
682 force_subclients[i] > 0x4f) {
683 dev_err(&client->dev,
684 "invalid subclient address %d; must be 0x48-0x4f\n",
685 force_subclients[i]);
686 err = -ENODEV;
687 goto ERROR_SC_2;
688 }
689 }
690 asb100_write_value(client, ASB100_REG_I2C_SUBADDR,
691 (force_subclients[2] & 0x07) |
692 ((force_subclients[3] & 0x07) << 4));
693 sc_addr[0] = force_subclients[2];
694 sc_addr[1] = force_subclients[3];
695 } else {
696 int val = asb100_read_value(client, ASB100_REG_I2C_SUBADDR);
697 sc_addr[0] = 0x48 + (val & 0x07);
698 sc_addr[1] = 0x48 + ((val >> 4) & 0x07);
699 }
700
701 if (sc_addr[0] == sc_addr[1]) {
702 dev_err(&client->dev,
703 "duplicate addresses 0x%x for subclients\n",
704 sc_addr[0]);
705 err = -ENODEV;
706 goto ERROR_SC_2;
707 }
708
709 data->lm75[0] = i2c_new_dummy_device(adapter, sc_addr[0]);
710 if (IS_ERR(data->lm75[0])) {
711 dev_err(&client->dev,
712 "subclient %d registration at address 0x%x failed.\n",
713 1, sc_addr[0]);
714 err = PTR_ERR(data->lm75[0]);
715 goto ERROR_SC_2;
716 }
717
718 data->lm75[1] = i2c_new_dummy_device(adapter, sc_addr[1]);
719 if (IS_ERR(data->lm75[1])) {
720 dev_err(&client->dev,
721 "subclient %d registration at address 0x%x failed.\n",
722 2, sc_addr[1]);
723 err = PTR_ERR(data->lm75[1]);
724 goto ERROR_SC_3;
725 }
726
727 return 0;
728
729/* Undo inits in case of errors */
730ERROR_SC_3:
731 i2c_unregister_device(data->lm75[0]);
732ERROR_SC_2:
733 return err;
734}
735
736/* Return 0 if detection is successful, -ENODEV otherwise */
737static int asb100_detect(struct i2c_client *client,
738 struct i2c_board_info *info)
739{
740 struct i2c_adapter *adapter = client->adapter;
741 int val1, val2;
742
743 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
744 pr_debug("detect failed, smbus byte data not supported!\n");
745 return -ENODEV;
746 }
747
748 val1 = i2c_smbus_read_byte_data(client, ASB100_REG_BANK);
749 val2 = i2c_smbus_read_byte_data(client, ASB100_REG_CHIPMAN);
750
751 /* If we're in bank 0 */
752 if ((!(val1 & 0x07)) &&
753 /* Check for ASB100 ID (low byte) */
754 (((!(val1 & 0x80)) && (val2 != 0x94)) ||
755 /* Check for ASB100 ID (high byte ) */
756 ((val1 & 0x80) && (val2 != 0x06)))) {
757 pr_debug("detect failed, bad chip id 0x%02x!\n", val2);
758 return -ENODEV;
759 }
760
761 /* Put it now into bank 0 and Vendor ID High Byte */
762 i2c_smbus_write_byte_data(client, ASB100_REG_BANK,
763 (i2c_smbus_read_byte_data(client, ASB100_REG_BANK) & 0x78)
764 | 0x80);
765
766 /* Determine the chip type. */
767 val1 = i2c_smbus_read_byte_data(client, ASB100_REG_WCHIPID);
768 val2 = i2c_smbus_read_byte_data(client, ASB100_REG_CHIPMAN);
769
770 if (val1 != 0x31 || val2 != 0x06)
771 return -ENODEV;
772
773 strlcpy(info->type, "asb100", I2C_NAME_SIZE);
774
775 return 0;
776}
777
778static int asb100_probe(struct i2c_client *client,
779 const struct i2c_device_id *id)
780{
781 int err;
782 struct asb100_data *data;
783
784 data = devm_kzalloc(&client->dev, sizeof(struct asb100_data),
785 GFP_KERNEL);
786 if (!data)
787 return -ENOMEM;
788
789 i2c_set_clientdata(client, data);
790 mutex_init(&data->lock);
791 mutex_init(&data->update_lock);
792
793 /* Attach secondary lm75 clients */
794 err = asb100_detect_subclients(client);
795 if (err)
796 return err;
797
798 /* Initialize the chip */
799 asb100_init_client(client);
800
801 /* A few vars need to be filled upon startup */
802 data->fan_min[0] = asb100_read_value(client, ASB100_REG_FAN_MIN(0));
803 data->fan_min[1] = asb100_read_value(client, ASB100_REG_FAN_MIN(1));
804 data->fan_min[2] = asb100_read_value(client, ASB100_REG_FAN_MIN(2));
805
806 /* Register sysfs hooks */
807 err = sysfs_create_group(&client->dev.kobj, &asb100_group);
808 if (err)
809 goto ERROR3;
810
811 data->hwmon_dev = hwmon_device_register(&client->dev);
812 if (IS_ERR(data->hwmon_dev)) {
813 err = PTR_ERR(data->hwmon_dev);
814 goto ERROR4;
815 }
816
817 return 0;
818
819ERROR4:
820 sysfs_remove_group(&client->dev.kobj, &asb100_group);
821ERROR3:
822 i2c_unregister_device(data->lm75[1]);
823 i2c_unregister_device(data->lm75[0]);
824 return err;
825}
826
827static int asb100_remove(struct i2c_client *client)
828{
829 struct asb100_data *data = i2c_get_clientdata(client);
830
831 hwmon_device_unregister(data->hwmon_dev);
832 sysfs_remove_group(&client->dev.kobj, &asb100_group);
833
834 i2c_unregister_device(data->lm75[1]);
835 i2c_unregister_device(data->lm75[0]);
836
837 return 0;
838}
839
840/*
841 * The SMBus locks itself, usually, but nothing may access the chip between
842 * bank switches.
843 */
844static int asb100_read_value(struct i2c_client *client, u16 reg)
845{
846 struct asb100_data *data = i2c_get_clientdata(client);
847 struct i2c_client *cl;
848 int res, bank;
849
850 mutex_lock(&data->lock);
851
852 bank = (reg >> 8) & 0x0f;
853 if (bank > 2)
854 /* switch banks */
855 i2c_smbus_write_byte_data(client, ASB100_REG_BANK, bank);
856
857 if (bank == 0 || bank > 2) {
858 res = i2c_smbus_read_byte_data(client, reg & 0xff);
859 } else {
860 /* switch to subclient */
861 cl = data->lm75[bank - 1];
862
863 /* convert from ISA to LM75 I2C addresses */
864 switch (reg & 0xff) {
865 case 0x50: /* TEMP */
866 res = i2c_smbus_read_word_swapped(cl, 0);
867 break;
868 case 0x52: /* CONFIG */
869 res = i2c_smbus_read_byte_data(cl, 1);
870 break;
871 case 0x53: /* HYST */
872 res = i2c_smbus_read_word_swapped(cl, 2);
873 break;
874 case 0x55: /* MAX */
875 default:
876 res = i2c_smbus_read_word_swapped(cl, 3);
877 break;
878 }
879 }
880
881 if (bank > 2)
882 i2c_smbus_write_byte_data(client, ASB100_REG_BANK, 0);
883
884 mutex_unlock(&data->lock);
885
886 return res;
887}
888
889static void asb100_write_value(struct i2c_client *client, u16 reg, u16 value)
890{
891 struct asb100_data *data = i2c_get_clientdata(client);
892 struct i2c_client *cl;
893 int bank;
894
895 mutex_lock(&data->lock);
896
897 bank = (reg >> 8) & 0x0f;
898 if (bank > 2)
899 /* switch banks */
900 i2c_smbus_write_byte_data(client, ASB100_REG_BANK, bank);
901
902 if (bank == 0 || bank > 2) {
903 i2c_smbus_write_byte_data(client, reg & 0xff, value & 0xff);
904 } else {
905 /* switch to subclient */
906 cl = data->lm75[bank - 1];
907
908 /* convert from ISA to LM75 I2C addresses */
909 switch (reg & 0xff) {
910 case 0x52: /* CONFIG */
911 i2c_smbus_write_byte_data(cl, 1, value & 0xff);
912 break;
913 case 0x53: /* HYST */
914 i2c_smbus_write_word_swapped(cl, 2, value);
915 break;
916 case 0x55: /* MAX */
917 i2c_smbus_write_word_swapped(cl, 3, value);
918 break;
919 }
920 }
921
922 if (bank > 2)
923 i2c_smbus_write_byte_data(client, ASB100_REG_BANK, 0);
924
925 mutex_unlock(&data->lock);
926}
927
928static void asb100_init_client(struct i2c_client *client)
929{
930 struct asb100_data *data = i2c_get_clientdata(client);
931
932 data->vrm = vid_which_vrm();
933
934 /* Start monitoring */
935 asb100_write_value(client, ASB100_REG_CONFIG,
936 (asb100_read_value(client, ASB100_REG_CONFIG) & 0xf7) | 0x01);
937}
938
939static struct asb100_data *asb100_update_device(struct device *dev)
940{
941 struct i2c_client *client = to_i2c_client(dev);
942 struct asb100_data *data = i2c_get_clientdata(client);
943 int i;
944
945 mutex_lock(&data->update_lock);
946
947 if (time_after(jiffies, data->last_updated + HZ + HZ / 2)
948 || !data->valid) {
949
950 dev_dbg(&client->dev, "starting device update...\n");
951
952 /* 7 voltage inputs */
953 for (i = 0; i < 7; i++) {
954 data->in[i] = asb100_read_value(client,
955 ASB100_REG_IN(i));
956 data->in_min[i] = asb100_read_value(client,
957 ASB100_REG_IN_MIN(i));
958 data->in_max[i] = asb100_read_value(client,
959 ASB100_REG_IN_MAX(i));
960 }
961
962 /* 3 fan inputs */
963 for (i = 0; i < 3; i++) {
964 data->fan[i] = asb100_read_value(client,
965 ASB100_REG_FAN(i));
966 data->fan_min[i] = asb100_read_value(client,
967 ASB100_REG_FAN_MIN(i));
968 }
969
970 /* 4 temperature inputs */
971 for (i = 1; i <= 4; i++) {
972 data->temp[i-1] = asb100_read_value(client,
973 ASB100_REG_TEMP(i));
974 data->temp_max[i-1] = asb100_read_value(client,
975 ASB100_REG_TEMP_MAX(i));
976 data->temp_hyst[i-1] = asb100_read_value(client,
977 ASB100_REG_TEMP_HYST(i));
978 }
979
980 /* VID and fan divisors */
981 i = asb100_read_value(client, ASB100_REG_VID_FANDIV);
982 data->vid = i & 0x0f;
983 data->vid |= (asb100_read_value(client,
984 ASB100_REG_CHIPID) & 0x01) << 4;
985 data->fan_div[0] = (i >> 4) & 0x03;
986 data->fan_div[1] = (i >> 6) & 0x03;
987 data->fan_div[2] = (asb100_read_value(client,
988 ASB100_REG_PIN) >> 6) & 0x03;
989
990 /* PWM */
991 data->pwm = asb100_read_value(client, ASB100_REG_PWM1);
992
993 /* alarms */
994 data->alarms = asb100_read_value(client, ASB100_REG_ALARM1) +
995 (asb100_read_value(client, ASB100_REG_ALARM2) << 8);
996
997 data->last_updated = jiffies;
998 data->valid = 1;
999
1000 dev_dbg(&client->dev, "... device update complete\n");
1001 }
1002
1003 mutex_unlock(&data->update_lock);
1004
1005 return data;
1006}
1007
1008module_i2c_driver(asb100_driver);
1009
1010MODULE_AUTHOR("Mark M. Hoffman <mhoffman@lightlink.com>");
1011MODULE_DESCRIPTION("ASB100 Bach driver");
1012MODULE_LICENSE("GPL");
1/*
2 * asb100.c - Part of lm_sensors, Linux kernel modules for hardware
3 * monitoring
4 *
5 * Copyright (C) 2004 Mark M. Hoffman <mhoffman@lightlink.com>
6 *
7 * (derived from w83781d.c)
8 *
9 * Copyright (C) 1998 - 2003 Frodo Looijaard <frodol@dds.nl>,
10 * Philip Edelbrock <phil@netroedge.com>, and
11 * Mark Studebaker <mdsxyz123@yahoo.com>
12 *
13 * This program is free software; you can redistribute it and/or modify
14 * it under the terms of the GNU General Public License as published by
15 * the Free Software Foundation; either version 2 of the License, or
16 * (at your option) any later version.
17 *
18 * This program is distributed in the hope that it will be useful,
19 * but WITHOUT ANY WARRANTY; without even the implied warranty of
20 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
21 * GNU General Public License for more details.
22 *
23 * You should have received a copy of the GNU General Public License
24 * along with this program; if not, write to the Free Software
25 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
26 */
27
28/*
29 * This driver supports the hardware sensor chips: Asus ASB100 and
30 * ASB100-A "BACH".
31 *
32 * ASB100-A supports pwm1, while plain ASB100 does not. There is no known
33 * way for the driver to tell which one is there.
34 *
35 * Chip #vin #fanin #pwm #temp wchipid vendid i2c ISA
36 * asb100 7 3 1 4 0x31 0x0694 yes no
37 */
38
39#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
40
41#include <linux/module.h>
42#include <linux/slab.h>
43#include <linux/i2c.h>
44#include <linux/hwmon.h>
45#include <linux/hwmon-sysfs.h>
46#include <linux/hwmon-vid.h>
47#include <linux/err.h>
48#include <linux/init.h>
49#include <linux/jiffies.h>
50#include <linux/mutex.h>
51#include "lm75.h"
52
53/* I2C addresses to scan */
54static const unsigned short normal_i2c[] = { 0x2d, I2C_CLIENT_END };
55
56static unsigned short force_subclients[4];
57module_param_array(force_subclients, short, NULL, 0);
58MODULE_PARM_DESC(force_subclients,
59 "List of subclient addresses: {bus, clientaddr, subclientaddr1, subclientaddr2}");
60
61/* Voltage IN registers 0-6 */
62#define ASB100_REG_IN(nr) (0x20 + (nr))
63#define ASB100_REG_IN_MAX(nr) (0x2b + (nr * 2))
64#define ASB100_REG_IN_MIN(nr) (0x2c + (nr * 2))
65
66/* FAN IN registers 1-3 */
67#define ASB100_REG_FAN(nr) (0x28 + (nr))
68#define ASB100_REG_FAN_MIN(nr) (0x3b + (nr))
69
70/* TEMPERATURE registers 1-4 */
71static const u16 asb100_reg_temp[] = {0, 0x27, 0x150, 0x250, 0x17};
72static const u16 asb100_reg_temp_max[] = {0, 0x39, 0x155, 0x255, 0x18};
73static const u16 asb100_reg_temp_hyst[] = {0, 0x3a, 0x153, 0x253, 0x19};
74
75#define ASB100_REG_TEMP(nr) (asb100_reg_temp[nr])
76#define ASB100_REG_TEMP_MAX(nr) (asb100_reg_temp_max[nr])
77#define ASB100_REG_TEMP_HYST(nr) (asb100_reg_temp_hyst[nr])
78
79#define ASB100_REG_TEMP2_CONFIG 0x0152
80#define ASB100_REG_TEMP3_CONFIG 0x0252
81
82
83#define ASB100_REG_CONFIG 0x40
84#define ASB100_REG_ALARM1 0x41
85#define ASB100_REG_ALARM2 0x42
86#define ASB100_REG_SMIM1 0x43
87#define ASB100_REG_SMIM2 0x44
88#define ASB100_REG_VID_FANDIV 0x47
89#define ASB100_REG_I2C_ADDR 0x48
90#define ASB100_REG_CHIPID 0x49
91#define ASB100_REG_I2C_SUBADDR 0x4a
92#define ASB100_REG_PIN 0x4b
93#define ASB100_REG_IRQ 0x4c
94#define ASB100_REG_BANK 0x4e
95#define ASB100_REG_CHIPMAN 0x4f
96
97#define ASB100_REG_WCHIPID 0x58
98
99/* bit 7 -> enable, bits 0-3 -> duty cycle */
100#define ASB100_REG_PWM1 0x59
101
102/*
103 * CONVERSIONS
104 * Rounding and limit checking is only done on the TO_REG variants.
105 */
106
107/* These constants are a guess, consistent w/ w83781d */
108#define ASB100_IN_MIN 0
109#define ASB100_IN_MAX 4080
110
111/*
112 * IN: 1/1000 V (0V to 4.08V)
113 * REG: 16mV/bit
114 */
115static u8 IN_TO_REG(unsigned val)
116{
117 unsigned nval = clamp_val(val, ASB100_IN_MIN, ASB100_IN_MAX);
118 return (nval + 8) / 16;
119}
120
121static unsigned IN_FROM_REG(u8 reg)
122{
123 return reg * 16;
124}
125
126static u8 FAN_TO_REG(long rpm, int div)
127{
128 if (rpm == -1)
129 return 0;
130 if (rpm == 0)
131 return 255;
132 rpm = clamp_val(rpm, 1, 1000000);
133 return clamp_val((1350000 + rpm * div / 2) / (rpm * div), 1, 254);
134}
135
136static int FAN_FROM_REG(u8 val, int div)
137{
138 return val == 0 ? -1 : val == 255 ? 0 : 1350000 / (val * div);
139}
140
141/* These constants are a guess, consistent w/ w83781d */
142#define ASB100_TEMP_MIN -128000
143#define ASB100_TEMP_MAX 127000
144
145/*
146 * TEMP: 0.001C/bit (-128C to +127C)
147 * REG: 1C/bit, two's complement
148 */
149static u8 TEMP_TO_REG(long temp)
150{
151 int ntemp = clamp_val(temp, ASB100_TEMP_MIN, ASB100_TEMP_MAX);
152 ntemp += (ntemp < 0 ? -500 : 500);
153 return (u8)(ntemp / 1000);
154}
155
156static int TEMP_FROM_REG(u8 reg)
157{
158 return (s8)reg * 1000;
159}
160
161/*
162 * PWM: 0 - 255 per sensors documentation
163 * REG: (6.25% duty cycle per bit)
164 */
165static u8 ASB100_PWM_TO_REG(int pwm)
166{
167 pwm = clamp_val(pwm, 0, 255);
168 return (u8)(pwm / 16);
169}
170
171static int ASB100_PWM_FROM_REG(u8 reg)
172{
173 return reg * 16;
174}
175
176#define DIV_FROM_REG(val) (1 << (val))
177
178/*
179 * FAN DIV: 1, 2, 4, or 8 (defaults to 2)
180 * REG: 0, 1, 2, or 3 (respectively) (defaults to 1)
181 */
182static u8 DIV_TO_REG(long val)
183{
184 return val == 8 ? 3 : val == 4 ? 2 : val == 1 ? 0 : 1;
185}
186
187/*
188 * For each registered client, we need to keep some data in memory. That
189 * data is pointed to by client->data. The structure itself is
190 * dynamically allocated, at the same time the client itself is allocated.
191 */
192struct asb100_data {
193 struct device *hwmon_dev;
194 struct mutex lock;
195
196 struct mutex update_lock;
197 unsigned long last_updated; /* In jiffies */
198
199 /* array of 2 pointers to subclients */
200 struct i2c_client *lm75[2];
201
202 char valid; /* !=0 if following fields are valid */
203 u8 in[7]; /* Register value */
204 u8 in_max[7]; /* Register value */
205 u8 in_min[7]; /* Register value */
206 u8 fan[3]; /* Register value */
207 u8 fan_min[3]; /* Register value */
208 u16 temp[4]; /* Register value (0 and 3 are u8 only) */
209 u16 temp_max[4]; /* Register value (0 and 3 are u8 only) */
210 u16 temp_hyst[4]; /* Register value (0 and 3 are u8 only) */
211 u8 fan_div[3]; /* Register encoding, right justified */
212 u8 pwm; /* Register encoding */
213 u8 vid; /* Register encoding, combined */
214 u32 alarms; /* Register encoding, combined */
215 u8 vrm;
216};
217
218static int asb100_read_value(struct i2c_client *client, u16 reg);
219static void asb100_write_value(struct i2c_client *client, u16 reg, u16 val);
220
221static int asb100_probe(struct i2c_client *client,
222 const struct i2c_device_id *id);
223static int asb100_detect(struct i2c_client *client,
224 struct i2c_board_info *info);
225static int asb100_remove(struct i2c_client *client);
226static struct asb100_data *asb100_update_device(struct device *dev);
227static void asb100_init_client(struct i2c_client *client);
228
229static const struct i2c_device_id asb100_id[] = {
230 { "asb100", 0 },
231 { }
232};
233MODULE_DEVICE_TABLE(i2c, asb100_id);
234
235static struct i2c_driver asb100_driver = {
236 .class = I2C_CLASS_HWMON,
237 .driver = {
238 .name = "asb100",
239 },
240 .probe = asb100_probe,
241 .remove = asb100_remove,
242 .id_table = asb100_id,
243 .detect = asb100_detect,
244 .address_list = normal_i2c,
245};
246
247/* 7 Voltages */
248#define show_in_reg(reg) \
249static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \
250 char *buf) \
251{ \
252 int nr = to_sensor_dev_attr(attr)->index; \
253 struct asb100_data *data = asb100_update_device(dev); \
254 return sprintf(buf, "%d\n", IN_FROM_REG(data->reg[nr])); \
255}
256
257show_in_reg(in)
258show_in_reg(in_min)
259show_in_reg(in_max)
260
261#define set_in_reg(REG, reg) \
262static ssize_t set_in_##reg(struct device *dev, struct device_attribute *attr, \
263 const char *buf, size_t count) \
264{ \
265 int nr = to_sensor_dev_attr(attr)->index; \
266 struct i2c_client *client = to_i2c_client(dev); \
267 struct asb100_data *data = i2c_get_clientdata(client); \
268 unsigned long val; \
269 int err = kstrtoul(buf, 10, &val); \
270 if (err) \
271 return err; \
272 mutex_lock(&data->update_lock); \
273 data->in_##reg[nr] = IN_TO_REG(val); \
274 asb100_write_value(client, ASB100_REG_IN_##REG(nr), \
275 data->in_##reg[nr]); \
276 mutex_unlock(&data->update_lock); \
277 return count; \
278}
279
280set_in_reg(MIN, min)
281set_in_reg(MAX, max)
282
283#define sysfs_in(offset) \
284static SENSOR_DEVICE_ATTR(in##offset##_input, S_IRUGO, \
285 show_in, NULL, offset); \
286static SENSOR_DEVICE_ATTR(in##offset##_min, S_IRUGO | S_IWUSR, \
287 show_in_min, set_in_min, offset); \
288static SENSOR_DEVICE_ATTR(in##offset##_max, S_IRUGO | S_IWUSR, \
289 show_in_max, set_in_max, offset)
290
291sysfs_in(0);
292sysfs_in(1);
293sysfs_in(2);
294sysfs_in(3);
295sysfs_in(4);
296sysfs_in(5);
297sysfs_in(6);
298
299/* 3 Fans */
300static ssize_t show_fan(struct device *dev, struct device_attribute *attr,
301 char *buf)
302{
303 int nr = to_sensor_dev_attr(attr)->index;
304 struct asb100_data *data = asb100_update_device(dev);
305 return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan[nr],
306 DIV_FROM_REG(data->fan_div[nr])));
307}
308
309static ssize_t show_fan_min(struct device *dev, struct device_attribute *attr,
310 char *buf)
311{
312 int nr = to_sensor_dev_attr(attr)->index;
313 struct asb100_data *data = asb100_update_device(dev);
314 return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan_min[nr],
315 DIV_FROM_REG(data->fan_div[nr])));
316}
317
318static ssize_t show_fan_div(struct device *dev, struct device_attribute *attr,
319 char *buf)
320{
321 int nr = to_sensor_dev_attr(attr)->index;
322 struct asb100_data *data = asb100_update_device(dev);
323 return sprintf(buf, "%d\n", DIV_FROM_REG(data->fan_div[nr]));
324}
325
326static ssize_t set_fan_min(struct device *dev, struct device_attribute *attr,
327 const char *buf, size_t count)
328{
329 int nr = to_sensor_dev_attr(attr)->index;
330 struct i2c_client *client = to_i2c_client(dev);
331 struct asb100_data *data = i2c_get_clientdata(client);
332 unsigned long val;
333 int err;
334
335 err = kstrtoul(buf, 10, &val);
336 if (err)
337 return err;
338
339 mutex_lock(&data->update_lock);
340 data->fan_min[nr] = FAN_TO_REG(val, DIV_FROM_REG(data->fan_div[nr]));
341 asb100_write_value(client, ASB100_REG_FAN_MIN(nr), data->fan_min[nr]);
342 mutex_unlock(&data->update_lock);
343 return count;
344}
345
346/*
347 * Note: we save and restore the fan minimum here, because its value is
348 * determined in part by the fan divisor. This follows the principle of
349 * least surprise; the user doesn't expect the fan minimum to change just
350 * because the divisor changed.
351 */
352static ssize_t set_fan_div(struct device *dev, struct device_attribute *attr,
353 const char *buf, size_t count)
354{
355 int nr = to_sensor_dev_attr(attr)->index;
356 struct i2c_client *client = to_i2c_client(dev);
357 struct asb100_data *data = i2c_get_clientdata(client);
358 unsigned long min;
359 int reg;
360 unsigned long val;
361 int err;
362
363 err = kstrtoul(buf, 10, &val);
364 if (err)
365 return err;
366
367 mutex_lock(&data->update_lock);
368
369 min = FAN_FROM_REG(data->fan_min[nr],
370 DIV_FROM_REG(data->fan_div[nr]));
371 data->fan_div[nr] = DIV_TO_REG(val);
372
373 switch (nr) {
374 case 0: /* fan 1 */
375 reg = asb100_read_value(client, ASB100_REG_VID_FANDIV);
376 reg = (reg & 0xcf) | (data->fan_div[0] << 4);
377 asb100_write_value(client, ASB100_REG_VID_FANDIV, reg);
378 break;
379
380 case 1: /* fan 2 */
381 reg = asb100_read_value(client, ASB100_REG_VID_FANDIV);
382 reg = (reg & 0x3f) | (data->fan_div[1] << 6);
383 asb100_write_value(client, ASB100_REG_VID_FANDIV, reg);
384 break;
385
386 case 2: /* fan 3 */
387 reg = asb100_read_value(client, ASB100_REG_PIN);
388 reg = (reg & 0x3f) | (data->fan_div[2] << 6);
389 asb100_write_value(client, ASB100_REG_PIN, reg);
390 break;
391 }
392
393 data->fan_min[nr] =
394 FAN_TO_REG(min, DIV_FROM_REG(data->fan_div[nr]));
395 asb100_write_value(client, ASB100_REG_FAN_MIN(nr), data->fan_min[nr]);
396
397 mutex_unlock(&data->update_lock);
398
399 return count;
400}
401
402#define sysfs_fan(offset) \
403static SENSOR_DEVICE_ATTR(fan##offset##_input, S_IRUGO, \
404 show_fan, NULL, offset - 1); \
405static SENSOR_DEVICE_ATTR(fan##offset##_min, S_IRUGO | S_IWUSR, \
406 show_fan_min, set_fan_min, offset - 1); \
407static SENSOR_DEVICE_ATTR(fan##offset##_div, S_IRUGO | S_IWUSR, \
408 show_fan_div, set_fan_div, offset - 1)
409
410sysfs_fan(1);
411sysfs_fan(2);
412sysfs_fan(3);
413
414/* 4 Temp. Sensors */
415static int sprintf_temp_from_reg(u16 reg, char *buf, int nr)
416{
417 int ret = 0;
418
419 switch (nr) {
420 case 1: case 2:
421 ret = sprintf(buf, "%d\n", LM75_TEMP_FROM_REG(reg));
422 break;
423 case 0: case 3: default:
424 ret = sprintf(buf, "%d\n", TEMP_FROM_REG(reg));
425 break;
426 }
427 return ret;
428}
429
430#define show_temp_reg(reg) \
431static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \
432 char *buf) \
433{ \
434 int nr = to_sensor_dev_attr(attr)->index; \
435 struct asb100_data *data = asb100_update_device(dev); \
436 return sprintf_temp_from_reg(data->reg[nr], buf, nr); \
437}
438
439show_temp_reg(temp);
440show_temp_reg(temp_max);
441show_temp_reg(temp_hyst);
442
443#define set_temp_reg(REG, reg) \
444static ssize_t set_##reg(struct device *dev, struct device_attribute *attr, \
445 const char *buf, size_t count) \
446{ \
447 int nr = to_sensor_dev_attr(attr)->index; \
448 struct i2c_client *client = to_i2c_client(dev); \
449 struct asb100_data *data = i2c_get_clientdata(client); \
450 long val; \
451 int err = kstrtol(buf, 10, &val); \
452 if (err) \
453 return err; \
454 mutex_lock(&data->update_lock); \
455 switch (nr) { \
456 case 1: case 2: \
457 data->reg[nr] = LM75_TEMP_TO_REG(val); \
458 break; \
459 case 0: case 3: default: \
460 data->reg[nr] = TEMP_TO_REG(val); \
461 break; \
462 } \
463 asb100_write_value(client, ASB100_REG_TEMP_##REG(nr+1), \
464 data->reg[nr]); \
465 mutex_unlock(&data->update_lock); \
466 return count; \
467}
468
469set_temp_reg(MAX, temp_max);
470set_temp_reg(HYST, temp_hyst);
471
472#define sysfs_temp(num) \
473static SENSOR_DEVICE_ATTR(temp##num##_input, S_IRUGO, \
474 show_temp, NULL, num - 1); \
475static SENSOR_DEVICE_ATTR(temp##num##_max, S_IRUGO | S_IWUSR, \
476 show_temp_max, set_temp_max, num - 1); \
477static SENSOR_DEVICE_ATTR(temp##num##_max_hyst, S_IRUGO | S_IWUSR, \
478 show_temp_hyst, set_temp_hyst, num - 1)
479
480sysfs_temp(1);
481sysfs_temp(2);
482sysfs_temp(3);
483sysfs_temp(4);
484
485/* VID */
486static ssize_t show_vid(struct device *dev, struct device_attribute *attr,
487 char *buf)
488{
489 struct asb100_data *data = asb100_update_device(dev);
490 return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm));
491}
492
493static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid, NULL);
494
495/* VRM */
496static ssize_t show_vrm(struct device *dev, struct device_attribute *attr,
497 char *buf)
498{
499 struct asb100_data *data = dev_get_drvdata(dev);
500 return sprintf(buf, "%d\n", data->vrm);
501}
502
503static ssize_t set_vrm(struct device *dev, struct device_attribute *attr,
504 const char *buf, size_t count)
505{
506 struct asb100_data *data = dev_get_drvdata(dev);
507 unsigned long val;
508 int err;
509
510 err = kstrtoul(buf, 10, &val);
511 if (err)
512 return err;
513
514 if (val > 255)
515 return -EINVAL;
516
517 data->vrm = val;
518 return count;
519}
520
521/* Alarms */
522static DEVICE_ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm, set_vrm);
523
524static ssize_t show_alarms(struct device *dev, struct device_attribute *attr,
525 char *buf)
526{
527 struct asb100_data *data = asb100_update_device(dev);
528 return sprintf(buf, "%u\n", data->alarms);
529}
530
531static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
532
533static ssize_t show_alarm(struct device *dev, struct device_attribute *attr,
534 char *buf)
535{
536 int bitnr = to_sensor_dev_attr(attr)->index;
537 struct asb100_data *data = asb100_update_device(dev);
538 return sprintf(buf, "%u\n", (data->alarms >> bitnr) & 1);
539}
540static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0);
541static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 1);
542static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 2);
543static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 3);
544static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 8);
545static SENSOR_DEVICE_ATTR(fan1_alarm, S_IRUGO, show_alarm, NULL, 6);
546static SENSOR_DEVICE_ATTR(fan2_alarm, S_IRUGO, show_alarm, NULL, 7);
547static SENSOR_DEVICE_ATTR(fan3_alarm, S_IRUGO, show_alarm, NULL, 11);
548static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 4);
549static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 5);
550static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 13);
551
552/* 1 PWM */
553static ssize_t show_pwm1(struct device *dev, struct device_attribute *attr,
554 char *buf)
555{
556 struct asb100_data *data = asb100_update_device(dev);
557 return sprintf(buf, "%d\n", ASB100_PWM_FROM_REG(data->pwm & 0x0f));
558}
559
560static ssize_t set_pwm1(struct device *dev, struct device_attribute *attr,
561 const char *buf, size_t count)
562{
563 struct i2c_client *client = to_i2c_client(dev);
564 struct asb100_data *data = i2c_get_clientdata(client);
565 unsigned long val;
566 int err;
567
568 err = kstrtoul(buf, 10, &val);
569 if (err)
570 return err;
571
572 mutex_lock(&data->update_lock);
573 data->pwm &= 0x80; /* keep the enable bit */
574 data->pwm |= (0x0f & ASB100_PWM_TO_REG(val));
575 asb100_write_value(client, ASB100_REG_PWM1, data->pwm);
576 mutex_unlock(&data->update_lock);
577 return count;
578}
579
580static ssize_t show_pwm_enable1(struct device *dev,
581 struct device_attribute *attr, char *buf)
582{
583 struct asb100_data *data = asb100_update_device(dev);
584 return sprintf(buf, "%d\n", (data->pwm & 0x80) ? 1 : 0);
585}
586
587static ssize_t set_pwm_enable1(struct device *dev,
588 struct device_attribute *attr, const char *buf, size_t count)
589{
590 struct i2c_client *client = to_i2c_client(dev);
591 struct asb100_data *data = i2c_get_clientdata(client);
592 unsigned long val;
593 int err;
594
595 err = kstrtoul(buf, 10, &val);
596 if (err)
597 return err;
598
599 mutex_lock(&data->update_lock);
600 data->pwm &= 0x0f; /* keep the duty cycle bits */
601 data->pwm |= (val ? 0x80 : 0x00);
602 asb100_write_value(client, ASB100_REG_PWM1, data->pwm);
603 mutex_unlock(&data->update_lock);
604 return count;
605}
606
607static DEVICE_ATTR(pwm1, S_IRUGO | S_IWUSR, show_pwm1, set_pwm1);
608static DEVICE_ATTR(pwm1_enable, S_IRUGO | S_IWUSR,
609 show_pwm_enable1, set_pwm_enable1);
610
611static struct attribute *asb100_attributes[] = {
612 &sensor_dev_attr_in0_input.dev_attr.attr,
613 &sensor_dev_attr_in0_min.dev_attr.attr,
614 &sensor_dev_attr_in0_max.dev_attr.attr,
615 &sensor_dev_attr_in1_input.dev_attr.attr,
616 &sensor_dev_attr_in1_min.dev_attr.attr,
617 &sensor_dev_attr_in1_max.dev_attr.attr,
618 &sensor_dev_attr_in2_input.dev_attr.attr,
619 &sensor_dev_attr_in2_min.dev_attr.attr,
620 &sensor_dev_attr_in2_max.dev_attr.attr,
621 &sensor_dev_attr_in3_input.dev_attr.attr,
622 &sensor_dev_attr_in3_min.dev_attr.attr,
623 &sensor_dev_attr_in3_max.dev_attr.attr,
624 &sensor_dev_attr_in4_input.dev_attr.attr,
625 &sensor_dev_attr_in4_min.dev_attr.attr,
626 &sensor_dev_attr_in4_max.dev_attr.attr,
627 &sensor_dev_attr_in5_input.dev_attr.attr,
628 &sensor_dev_attr_in5_min.dev_attr.attr,
629 &sensor_dev_attr_in5_max.dev_attr.attr,
630 &sensor_dev_attr_in6_input.dev_attr.attr,
631 &sensor_dev_attr_in6_min.dev_attr.attr,
632 &sensor_dev_attr_in6_max.dev_attr.attr,
633
634 &sensor_dev_attr_fan1_input.dev_attr.attr,
635 &sensor_dev_attr_fan1_min.dev_attr.attr,
636 &sensor_dev_attr_fan1_div.dev_attr.attr,
637 &sensor_dev_attr_fan2_input.dev_attr.attr,
638 &sensor_dev_attr_fan2_min.dev_attr.attr,
639 &sensor_dev_attr_fan2_div.dev_attr.attr,
640 &sensor_dev_attr_fan3_input.dev_attr.attr,
641 &sensor_dev_attr_fan3_min.dev_attr.attr,
642 &sensor_dev_attr_fan3_div.dev_attr.attr,
643
644 &sensor_dev_attr_temp1_input.dev_attr.attr,
645 &sensor_dev_attr_temp1_max.dev_attr.attr,
646 &sensor_dev_attr_temp1_max_hyst.dev_attr.attr,
647 &sensor_dev_attr_temp2_input.dev_attr.attr,
648 &sensor_dev_attr_temp2_max.dev_attr.attr,
649 &sensor_dev_attr_temp2_max_hyst.dev_attr.attr,
650 &sensor_dev_attr_temp3_input.dev_attr.attr,
651 &sensor_dev_attr_temp3_max.dev_attr.attr,
652 &sensor_dev_attr_temp3_max_hyst.dev_attr.attr,
653 &sensor_dev_attr_temp4_input.dev_attr.attr,
654 &sensor_dev_attr_temp4_max.dev_attr.attr,
655 &sensor_dev_attr_temp4_max_hyst.dev_attr.attr,
656
657 &sensor_dev_attr_in0_alarm.dev_attr.attr,
658 &sensor_dev_attr_in1_alarm.dev_attr.attr,
659 &sensor_dev_attr_in2_alarm.dev_attr.attr,
660 &sensor_dev_attr_in3_alarm.dev_attr.attr,
661 &sensor_dev_attr_in4_alarm.dev_attr.attr,
662 &sensor_dev_attr_fan1_alarm.dev_attr.attr,
663 &sensor_dev_attr_fan2_alarm.dev_attr.attr,
664 &sensor_dev_attr_fan3_alarm.dev_attr.attr,
665 &sensor_dev_attr_temp1_alarm.dev_attr.attr,
666 &sensor_dev_attr_temp2_alarm.dev_attr.attr,
667 &sensor_dev_attr_temp3_alarm.dev_attr.attr,
668
669 &dev_attr_cpu0_vid.attr,
670 &dev_attr_vrm.attr,
671 &dev_attr_alarms.attr,
672 &dev_attr_pwm1.attr,
673 &dev_attr_pwm1_enable.attr,
674
675 NULL
676};
677
678static const struct attribute_group asb100_group = {
679 .attrs = asb100_attributes,
680};
681
682static int asb100_detect_subclients(struct i2c_client *client)
683{
684 int i, id, err;
685 int address = client->addr;
686 unsigned short sc_addr[2];
687 struct asb100_data *data = i2c_get_clientdata(client);
688 struct i2c_adapter *adapter = client->adapter;
689
690 id = i2c_adapter_id(adapter);
691
692 if (force_subclients[0] == id && force_subclients[1] == address) {
693 for (i = 2; i <= 3; i++) {
694 if (force_subclients[i] < 0x48 ||
695 force_subclients[i] > 0x4f) {
696 dev_err(&client->dev,
697 "invalid subclient address %d; must be 0x48-0x4f\n",
698 force_subclients[i]);
699 err = -ENODEV;
700 goto ERROR_SC_2;
701 }
702 }
703 asb100_write_value(client, ASB100_REG_I2C_SUBADDR,
704 (force_subclients[2] & 0x07) |
705 ((force_subclients[3] & 0x07) << 4));
706 sc_addr[0] = force_subclients[2];
707 sc_addr[1] = force_subclients[3];
708 } else {
709 int val = asb100_read_value(client, ASB100_REG_I2C_SUBADDR);
710 sc_addr[0] = 0x48 + (val & 0x07);
711 sc_addr[1] = 0x48 + ((val >> 4) & 0x07);
712 }
713
714 if (sc_addr[0] == sc_addr[1]) {
715 dev_err(&client->dev,
716 "duplicate addresses 0x%x for subclients\n",
717 sc_addr[0]);
718 err = -ENODEV;
719 goto ERROR_SC_2;
720 }
721
722 data->lm75[0] = i2c_new_dummy(adapter, sc_addr[0]);
723 if (!data->lm75[0]) {
724 dev_err(&client->dev,
725 "subclient %d registration at address 0x%x failed.\n",
726 1, sc_addr[0]);
727 err = -ENOMEM;
728 goto ERROR_SC_2;
729 }
730
731 data->lm75[1] = i2c_new_dummy(adapter, sc_addr[1]);
732 if (!data->lm75[1]) {
733 dev_err(&client->dev,
734 "subclient %d registration at address 0x%x failed.\n",
735 2, sc_addr[1]);
736 err = -ENOMEM;
737 goto ERROR_SC_3;
738 }
739
740 return 0;
741
742/* Undo inits in case of errors */
743ERROR_SC_3:
744 i2c_unregister_device(data->lm75[0]);
745ERROR_SC_2:
746 return err;
747}
748
749/* Return 0 if detection is successful, -ENODEV otherwise */
750static int asb100_detect(struct i2c_client *client,
751 struct i2c_board_info *info)
752{
753 struct i2c_adapter *adapter = client->adapter;
754 int val1, val2;
755
756 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
757 pr_debug("detect failed, smbus byte data not supported!\n");
758 return -ENODEV;
759 }
760
761 val1 = i2c_smbus_read_byte_data(client, ASB100_REG_BANK);
762 val2 = i2c_smbus_read_byte_data(client, ASB100_REG_CHIPMAN);
763
764 /* If we're in bank 0 */
765 if ((!(val1 & 0x07)) &&
766 /* Check for ASB100 ID (low byte) */
767 (((!(val1 & 0x80)) && (val2 != 0x94)) ||
768 /* Check for ASB100 ID (high byte ) */
769 ((val1 & 0x80) && (val2 != 0x06)))) {
770 pr_debug("detect failed, bad chip id 0x%02x!\n", val2);
771 return -ENODEV;
772 }
773
774 /* Put it now into bank 0 and Vendor ID High Byte */
775 i2c_smbus_write_byte_data(client, ASB100_REG_BANK,
776 (i2c_smbus_read_byte_data(client, ASB100_REG_BANK) & 0x78)
777 | 0x80);
778
779 /* Determine the chip type. */
780 val1 = i2c_smbus_read_byte_data(client, ASB100_REG_WCHIPID);
781 val2 = i2c_smbus_read_byte_data(client, ASB100_REG_CHIPMAN);
782
783 if (val1 != 0x31 || val2 != 0x06)
784 return -ENODEV;
785
786 strlcpy(info->type, "asb100", I2C_NAME_SIZE);
787
788 return 0;
789}
790
791static int asb100_probe(struct i2c_client *client,
792 const struct i2c_device_id *id)
793{
794 int err;
795 struct asb100_data *data;
796
797 data = devm_kzalloc(&client->dev, sizeof(struct asb100_data),
798 GFP_KERNEL);
799 if (!data)
800 return -ENOMEM;
801
802 i2c_set_clientdata(client, data);
803 mutex_init(&data->lock);
804 mutex_init(&data->update_lock);
805
806 /* Attach secondary lm75 clients */
807 err = asb100_detect_subclients(client);
808 if (err)
809 return err;
810
811 /* Initialize the chip */
812 asb100_init_client(client);
813
814 /* A few vars need to be filled upon startup */
815 data->fan_min[0] = asb100_read_value(client, ASB100_REG_FAN_MIN(0));
816 data->fan_min[1] = asb100_read_value(client, ASB100_REG_FAN_MIN(1));
817 data->fan_min[2] = asb100_read_value(client, ASB100_REG_FAN_MIN(2));
818
819 /* Register sysfs hooks */
820 err = sysfs_create_group(&client->dev.kobj, &asb100_group);
821 if (err)
822 goto ERROR3;
823
824 data->hwmon_dev = hwmon_device_register(&client->dev);
825 if (IS_ERR(data->hwmon_dev)) {
826 err = PTR_ERR(data->hwmon_dev);
827 goto ERROR4;
828 }
829
830 return 0;
831
832ERROR4:
833 sysfs_remove_group(&client->dev.kobj, &asb100_group);
834ERROR3:
835 i2c_unregister_device(data->lm75[1]);
836 i2c_unregister_device(data->lm75[0]);
837 return err;
838}
839
840static int asb100_remove(struct i2c_client *client)
841{
842 struct asb100_data *data = i2c_get_clientdata(client);
843
844 hwmon_device_unregister(data->hwmon_dev);
845 sysfs_remove_group(&client->dev.kobj, &asb100_group);
846
847 i2c_unregister_device(data->lm75[1]);
848 i2c_unregister_device(data->lm75[0]);
849
850 return 0;
851}
852
853/*
854 * The SMBus locks itself, usually, but nothing may access the chip between
855 * bank switches.
856 */
857static int asb100_read_value(struct i2c_client *client, u16 reg)
858{
859 struct asb100_data *data = i2c_get_clientdata(client);
860 struct i2c_client *cl;
861 int res, bank;
862
863 mutex_lock(&data->lock);
864
865 bank = (reg >> 8) & 0x0f;
866 if (bank > 2)
867 /* switch banks */
868 i2c_smbus_write_byte_data(client, ASB100_REG_BANK, bank);
869
870 if (bank == 0 || bank > 2) {
871 res = i2c_smbus_read_byte_data(client, reg & 0xff);
872 } else {
873 /* switch to subclient */
874 cl = data->lm75[bank - 1];
875
876 /* convert from ISA to LM75 I2C addresses */
877 switch (reg & 0xff) {
878 case 0x50: /* TEMP */
879 res = i2c_smbus_read_word_swapped(cl, 0);
880 break;
881 case 0x52: /* CONFIG */
882 res = i2c_smbus_read_byte_data(cl, 1);
883 break;
884 case 0x53: /* HYST */
885 res = i2c_smbus_read_word_swapped(cl, 2);
886 break;
887 case 0x55: /* MAX */
888 default:
889 res = i2c_smbus_read_word_swapped(cl, 3);
890 break;
891 }
892 }
893
894 if (bank > 2)
895 i2c_smbus_write_byte_data(client, ASB100_REG_BANK, 0);
896
897 mutex_unlock(&data->lock);
898
899 return res;
900}
901
902static void asb100_write_value(struct i2c_client *client, u16 reg, u16 value)
903{
904 struct asb100_data *data = i2c_get_clientdata(client);
905 struct i2c_client *cl;
906 int bank;
907
908 mutex_lock(&data->lock);
909
910 bank = (reg >> 8) & 0x0f;
911 if (bank > 2)
912 /* switch banks */
913 i2c_smbus_write_byte_data(client, ASB100_REG_BANK, bank);
914
915 if (bank == 0 || bank > 2) {
916 i2c_smbus_write_byte_data(client, reg & 0xff, value & 0xff);
917 } else {
918 /* switch to subclient */
919 cl = data->lm75[bank - 1];
920
921 /* convert from ISA to LM75 I2C addresses */
922 switch (reg & 0xff) {
923 case 0x52: /* CONFIG */
924 i2c_smbus_write_byte_data(cl, 1, value & 0xff);
925 break;
926 case 0x53: /* HYST */
927 i2c_smbus_write_word_swapped(cl, 2, value);
928 break;
929 case 0x55: /* MAX */
930 i2c_smbus_write_word_swapped(cl, 3, value);
931 break;
932 }
933 }
934
935 if (bank > 2)
936 i2c_smbus_write_byte_data(client, ASB100_REG_BANK, 0);
937
938 mutex_unlock(&data->lock);
939}
940
941static void asb100_init_client(struct i2c_client *client)
942{
943 struct asb100_data *data = i2c_get_clientdata(client);
944
945 data->vrm = vid_which_vrm();
946
947 /* Start monitoring */
948 asb100_write_value(client, ASB100_REG_CONFIG,
949 (asb100_read_value(client, ASB100_REG_CONFIG) & 0xf7) | 0x01);
950}
951
952static struct asb100_data *asb100_update_device(struct device *dev)
953{
954 struct i2c_client *client = to_i2c_client(dev);
955 struct asb100_data *data = i2c_get_clientdata(client);
956 int i;
957
958 mutex_lock(&data->update_lock);
959
960 if (time_after(jiffies, data->last_updated + HZ + HZ / 2)
961 || !data->valid) {
962
963 dev_dbg(&client->dev, "starting device update...\n");
964
965 /* 7 voltage inputs */
966 for (i = 0; i < 7; i++) {
967 data->in[i] = asb100_read_value(client,
968 ASB100_REG_IN(i));
969 data->in_min[i] = asb100_read_value(client,
970 ASB100_REG_IN_MIN(i));
971 data->in_max[i] = asb100_read_value(client,
972 ASB100_REG_IN_MAX(i));
973 }
974
975 /* 3 fan inputs */
976 for (i = 0; i < 3; i++) {
977 data->fan[i] = asb100_read_value(client,
978 ASB100_REG_FAN(i));
979 data->fan_min[i] = asb100_read_value(client,
980 ASB100_REG_FAN_MIN(i));
981 }
982
983 /* 4 temperature inputs */
984 for (i = 1; i <= 4; i++) {
985 data->temp[i-1] = asb100_read_value(client,
986 ASB100_REG_TEMP(i));
987 data->temp_max[i-1] = asb100_read_value(client,
988 ASB100_REG_TEMP_MAX(i));
989 data->temp_hyst[i-1] = asb100_read_value(client,
990 ASB100_REG_TEMP_HYST(i));
991 }
992
993 /* VID and fan divisors */
994 i = asb100_read_value(client, ASB100_REG_VID_FANDIV);
995 data->vid = i & 0x0f;
996 data->vid |= (asb100_read_value(client,
997 ASB100_REG_CHIPID) & 0x01) << 4;
998 data->fan_div[0] = (i >> 4) & 0x03;
999 data->fan_div[1] = (i >> 6) & 0x03;
1000 data->fan_div[2] = (asb100_read_value(client,
1001 ASB100_REG_PIN) >> 6) & 0x03;
1002
1003 /* PWM */
1004 data->pwm = asb100_read_value(client, ASB100_REG_PWM1);
1005
1006 /* alarms */
1007 data->alarms = asb100_read_value(client, ASB100_REG_ALARM1) +
1008 (asb100_read_value(client, ASB100_REG_ALARM2) << 8);
1009
1010 data->last_updated = jiffies;
1011 data->valid = 1;
1012
1013 dev_dbg(&client->dev, "... device update complete\n");
1014 }
1015
1016 mutex_unlock(&data->update_lock);
1017
1018 return data;
1019}
1020
1021module_i2c_driver(asb100_driver);
1022
1023MODULE_AUTHOR("Mark M. Hoffman <mhoffman@lightlink.com>");
1024MODULE_DESCRIPTION("ASB100 Bach driver");
1025MODULE_LICENSE("GPL");