Loading...
1/*
2 * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
3 *
4 * This file is dual-licensed: you can use it either under the terms
5 * of the GPL or the X11 license, at your option. Note that this dual
6 * licensing only applies to this file, and not this project as a
7 * whole.
8 *
9 * a) This library is free software; you can redistribute it and/or
10 * modify it under the terms of the GNU General Public License as
11 * published by the Free Software Foundation; either version 2 of the
12 * License, or (at your option) any later version.
13 *
14 * This library is distributed in the hope that it will be useful,
15 * but WITHOUT ANY WARRANTY; without even the implied warranty of
16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
17 * GNU General Public License for more details.
18 *
19 * Or, alternatively,
20 *
21 * b) Permission is hereby granted, free of charge, to any person
22 * obtaining a copy of this software and associated documentation
23 * files (the "Software"), to deal in the Software without
24 * restriction, including without limitation the rights to use,
25 * copy, modify, merge, publish, distribute, sublicense, and/or
26 * sell copies of the Software, and to permit persons to whom the
27 * Software is furnished to do so, subject to the following
28 * conditions:
29 *
30 * The above copyright notice and this permission notice shall be
31 * included in all copies or substantial portions of the Software.
32 *
33 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
34 * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
35 * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
36 * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
37 * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
38 * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
39 * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
40 * OTHER DEALINGS IN THE SOFTWARE.
41 */
42
43/dts-v1/;
44
45#include "sun50i-h5.dtsi"
46
47#include <dt-bindings/gpio/gpio.h>
48
49/ {
50 model = "OrangePi Zero Plus2";
51 compatible = "xunlong,orangepi-zero-plus2", "allwinner,sun50i-h5";
52
53 aliases {
54 serial0 = &uart0;
55 };
56
57 chosen {
58 stdout-path = "serial0:115200n8";
59 };
60
61 connector {
62 compatible = "hdmi-connector";
63 type = "a";
64
65 port {
66 hdmi_con_in: endpoint {
67 remote-endpoint = <&hdmi_out_con>;
68 };
69 };
70 };
71
72 reg_vcc3v3: vcc3v3 {
73 compatible = "regulator-fixed";
74 regulator-name = "vcc3v3";
75 regulator-min-microvolt = <3300000>;
76 regulator-max-microvolt = <3300000>;
77 };
78
79 wifi_pwrseq: wifi_pwrseq {
80 compatible = "mmc-pwrseq-simple";
81 reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
82 post-power-on-delay-ms = <200>;
83 };
84};
85
86&de {
87 status = "okay";
88};
89
90&hdmi {
91 status = "okay";
92};
93
94&hdmi_out {
95 hdmi_out_con: endpoint {
96 remote-endpoint = <&hdmi_con_in>;
97 };
98};
99
100&mmc0 {
101 vmmc-supply = <®_vcc3v3>;
102 bus-width = <4>;
103 cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
104 status = "okay";
105};
106
107&mmc1 {
108 vmmc-supply = <®_vcc3v3>;
109 vqmmc-supply = <®_vcc3v3>;
110 mmc-pwrseq = <&wifi_pwrseq>;
111 bus-width = <4>;
112 non-removable;
113 status = "okay";
114
115 brcmf: wifi@1 {
116 reg = <1>;
117 compatible = "brcm,bcm4329-fmac";
118 interrupt-parent = <&r_pio>;
119 interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>; /* PL7 */
120 interrupt-names = "host-wake";
121 };
122};
123
124&mmc2 {
125 pinctrl-names = "default";
126 pinctrl-0 = <&mmc2_8bit_pins>;
127 vmmc-supply = <®_vcc3v3>;
128 bus-width = <8>;
129 non-removable;
130 cap-mmc-hw-reset;
131 status = "okay";
132};
133
134&uart0 {
135 pinctrl-names = "default";
136 pinctrl-0 = <&uart0_pa_pins>;
137 status = "okay";
138};
139
140&uart1 {
141 pinctrl-names = "default";
142 pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
143 status = "okay";
144};
1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2// Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
3
4/dts-v1/;
5
6#include "sun50i-h5.dtsi"
7
8#include <dt-bindings/gpio/gpio.h>
9
10/ {
11 model = "OrangePi Zero Plus2";
12 compatible = "xunlong,orangepi-zero-plus2", "allwinner,sun50i-h5";
13
14 aliases {
15 serial0 = &uart0;
16 };
17
18 chosen {
19 stdout-path = "serial0:115200n8";
20 };
21
22 connector {
23 compatible = "hdmi-connector";
24 type = "a";
25
26 port {
27 hdmi_con_in: endpoint {
28 remote-endpoint = <&hdmi_out_con>;
29 };
30 };
31 };
32
33 leds {
34 compatible = "gpio-leds";
35
36 led-0 {
37 label = "orangepi:green:pwr";
38 gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
39 default-state = "on";
40 };
41
42 led-1 {
43 label = "orangepi:red:status";
44 gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>;
45 };
46 };
47
48 reg_vcc3v3: vcc3v3 {
49 compatible = "regulator-fixed";
50 regulator-name = "vcc3v3";
51 regulator-min-microvolt = <3300000>;
52 regulator-max-microvolt = <3300000>;
53 };
54
55 wifi_pwrseq: wifi_pwrseq {
56 compatible = "mmc-pwrseq-simple";
57 reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
58 post-power-on-delay-ms = <200>;
59 };
60};
61
62&de {
63 status = "okay";
64};
65
66&ehci0 {
67 status = "okay";
68};
69
70&hdmi {
71 status = "okay";
72};
73
74&hdmi_out {
75 hdmi_out_con: endpoint {
76 remote-endpoint = <&hdmi_con_in>;
77 };
78};
79
80&mmc0 {
81 vmmc-supply = <®_vcc3v3>;
82 bus-width = <4>;
83 cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
84 status = "okay";
85};
86
87&mmc1 {
88 vmmc-supply = <®_vcc3v3>;
89 vqmmc-supply = <®_vcc3v3>;
90 mmc-pwrseq = <&wifi_pwrseq>;
91 bus-width = <4>;
92 non-removable;
93 status = "okay";
94
95 brcmf: wifi@1 {
96 reg = <1>;
97 compatible = "brcm,bcm4329-fmac";
98 interrupt-parent = <&r_pio>;
99 interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>; /* PL7 */
100 interrupt-names = "host-wake";
101 };
102};
103
104&mmc2 {
105 pinctrl-names = "default";
106 pinctrl-0 = <&mmc2_8bit_pins>;
107 vmmc-supply = <®_vcc3v3>;
108 bus-width = <8>;
109 non-removable;
110 cap-mmc-hw-reset;
111 status = "okay";
112};
113
114&ohci0 {
115 status = "okay";
116};
117
118&uart0 {
119 pinctrl-names = "default";
120 pinctrl-0 = <&uart0_pa_pins>;
121 status = "okay";
122};
123
124&uart1 {
125 pinctrl-names = "default";
126 pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
127 status = "okay";
128};
129
130&usb_otg {
131 /*
132 * According to schematics CN1 MicroUSB port can be used to take
133 * external 5V to power up the board VBUS. On the contrary CN1 MicroUSB
134 * port cannot provide power externally even if the board is powered
135 * via GPIO pins. It thus makes sense to force peripheral mode.
136 */
137 dr_mode = "peripheral";
138 status = "okay";
139};
140
141&usbphy {
142 status = "okay";
143};