1// SPDX-License-Identifier: GPL-2.0+
   2/*
   3 * Driver for PowerMac Z85c30 based ESCC cell found in the
   4 * "macio" ASICs of various PowerMac models
   5 * 
   6 * Copyright (C) 2003 Ben. Herrenschmidt (benh@kernel.crashing.org)
   7 *
   8 * Derived from drivers/macintosh/macserial.c by Paul Mackerras
   9 * and drivers/serial/sunzilog.c by David S. Miller
  10 *
  11 * Hrm... actually, I ripped most of sunzilog (Thanks David !) and
  12 * adapted special tweaks needed for us. I don't think it's worth
  13 * merging back those though. The DMA code still has to get in
  14 * and once done, I expect that driver to remain fairly stable in
  15 * the long term, unless we change the driver model again...
  16 *
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  17 * 2004-08-06 Harald Welte <laforge@gnumonks.org>
  18 *	- Enable BREAK interrupt
  19 *	- Add support for sysreq
  20 *
  21 * TODO:   - Add DMA support
  22 *         - Defer port shutdown to a few seconds after close
  23 *         - maybe put something right into uap->clk_divisor
  24 */
  25
  26#undef DEBUG
  27#undef DEBUG_HARD
  28#undef USE_CTRL_O_SYSRQ
  29
  30#include <linux/module.h>
  31#include <linux/tty.h>
  32
  33#include <linux/tty_flip.h>
  34#include <linux/major.h>
  35#include <linux/string.h>
  36#include <linux/fcntl.h>
  37#include <linux/mm.h>
  38#include <linux/kernel.h>
  39#include <linux/delay.h>
  40#include <linux/init.h>
  41#include <linux/console.h>
  42#include <linux/adb.h>
  43#include <linux/pmu.h>
  44#include <linux/bitops.h>
  45#include <linux/sysrq.h>
  46#include <linux/mutex.h>
  47#include <linux/of_address.h>
  48#include <linux/of_irq.h>
  49#include <asm/sections.h>
  50#include <asm/io.h>
  51#include <asm/irq.h>
  52
  53#ifdef CONFIG_PPC_PMAC
  54#include <asm/prom.h>
  55#include <asm/machdep.h>
  56#include <asm/pmac_feature.h>
  57#include <asm/dbdma.h>
  58#include <asm/macio.h>
  59#else
  60#include <linux/platform_device.h>
  61#define of_machine_is_compatible(x) (0)
  62#endif
  63
  64#if defined (CONFIG_SERIAL_PMACZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
  65#define SUPPORT_SYSRQ
  66#endif
  67
  68#include <linux/serial.h>
  69#include <linux/serial_core.h>
  70
  71#include "pmac_zilog.h"
  72
  73/* Not yet implemented */
  74#undef HAS_DBDMA
  75
  76static char version[] __initdata = "pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)";
  77MODULE_AUTHOR("Benjamin Herrenschmidt <benh@kernel.crashing.org>");
  78MODULE_DESCRIPTION("Driver for the Mac and PowerMac serial ports.");
  79MODULE_LICENSE("GPL");
  80
  81#ifdef CONFIG_SERIAL_PMACZILOG_TTYS
  82#define PMACZILOG_MAJOR		TTY_MAJOR
  83#define PMACZILOG_MINOR		64
  84#define PMACZILOG_NAME		"ttyS"
  85#else
  86#define PMACZILOG_MAJOR		204
  87#define PMACZILOG_MINOR		192
  88#define PMACZILOG_NAME		"ttyPZ"
  89#endif
  90
  91#define pmz_debug(fmt, arg...)	pr_debug("ttyPZ%d: " fmt, uap->port.line, ## arg)
  92#define pmz_error(fmt, arg...)	pr_err("ttyPZ%d: " fmt, uap->port.line, ## arg)
  93#define pmz_info(fmt, arg...)	pr_info("ttyPZ%d: " fmt, uap->port.line, ## arg)
  94
  95/*
  96 * For the sake of early serial console, we can do a pre-probe
  97 * (optional) of the ports at rather early boot time.
  98 */
  99static struct uart_pmac_port	pmz_ports[MAX_ZS_PORTS];
 100static int			pmz_ports_count;
 101
 102static struct uart_driver pmz_uart_reg = {
 103	.owner		=	THIS_MODULE,
 104	.driver_name	=	PMACZILOG_NAME,
 105	.dev_name	=	PMACZILOG_NAME,
 106	.major		=	PMACZILOG_MAJOR,
 107	.minor		=	PMACZILOG_MINOR,
 108};
 109
 110
 111/* 
 112 * Load all registers to reprogram the port
 113 * This function must only be called when the TX is not busy.  The UART
 114 * port lock must be held and local interrupts disabled.
 115 */
 116static void pmz_load_zsregs(struct uart_pmac_port *uap, u8 *regs)
 117{
 118	int i;
 119
 120	/* Let pending transmits finish.  */
 121	for (i = 0; i < 1000; i++) {
 122		unsigned char stat = read_zsreg(uap, R1);
 123		if (stat & ALL_SNT)
 124			break;
 125		udelay(100);
 126	}
 127
 128	ZS_CLEARERR(uap);
 129	zssync(uap);
 130	ZS_CLEARFIFO(uap);
 131	zssync(uap);
 132	ZS_CLEARERR(uap);
 133
 134	/* Disable all interrupts.  */
 135	write_zsreg(uap, R1,
 136		    regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
 137
 138	/* Set parity, sync config, stop bits, and clock divisor.  */
 139	write_zsreg(uap, R4, regs[R4]);
 140
 141	/* Set misc. TX/RX control bits.  */
 142	write_zsreg(uap, R10, regs[R10]);
 143
 144	/* Set TX/RX controls sans the enable bits.  */
 145	write_zsreg(uap, R3, regs[R3] & ~RxENABLE);
 146	write_zsreg(uap, R5, regs[R5] & ~TxENABLE);
 147
 148	/* now set R7 "prime" on ESCC */
 149	write_zsreg(uap, R15, regs[R15] | EN85C30);
 150	write_zsreg(uap, R7, regs[R7P]);
 151
 152	/* make sure we use R7 "non-prime" on ESCC */
 153	write_zsreg(uap, R15, regs[R15] & ~EN85C30);
 154
 155	/* Synchronous mode config.  */
 156	write_zsreg(uap, R6, regs[R6]);
 157	write_zsreg(uap, R7, regs[R7]);
 158
 159	/* Disable baud generator.  */
 160	write_zsreg(uap, R14, regs[R14] & ~BRENAB);
 161
 162	/* Clock mode control.  */
 163	write_zsreg(uap, R11, regs[R11]);
 164
 165	/* Lower and upper byte of baud rate generator divisor.  */
 166	write_zsreg(uap, R12, regs[R12]);
 167	write_zsreg(uap, R13, regs[R13]);
 168	
 169	/* Now rewrite R14, with BRENAB (if set).  */
 170	write_zsreg(uap, R14, regs[R14]);
 171
 172	/* Reset external status interrupts.  */
 173	write_zsreg(uap, R0, RES_EXT_INT);
 174	write_zsreg(uap, R0, RES_EXT_INT);
 175
 176	/* Rewrite R3/R5, this time without enables masked.  */
 177	write_zsreg(uap, R3, regs[R3]);
 178	write_zsreg(uap, R5, regs[R5]);
 179
 180	/* Rewrite R1, this time without IRQ enabled masked.  */
 181	write_zsreg(uap, R1, regs[R1]);
 182
 183	/* Enable interrupts */
 184	write_zsreg(uap, R9, regs[R9]);
 185}
 186
 187/* 
 188 * We do like sunzilog to avoid disrupting pending Tx
 189 * Reprogram the Zilog channel HW registers with the copies found in the
 190 * software state struct.  If the transmitter is busy, we defer this update
 191 * until the next TX complete interrupt.  Else, we do it right now.
 192 *
 193 * The UART port lock must be held and local interrupts disabled.
 194 */
 195static void pmz_maybe_update_regs(struct uart_pmac_port *uap)
 196{
 197	if (!ZS_REGS_HELD(uap)) {
 198		if (ZS_TX_ACTIVE(uap)) {
 199			uap->flags |= PMACZILOG_FLAG_REGS_HELD;
 200		} else {
 201			pmz_debug("pmz: maybe_update_regs: updating\n");
 202			pmz_load_zsregs(uap, uap->curregs);
 203		}
 204	}
 205}
 206
 207static void pmz_interrupt_control(struct uart_pmac_port *uap, int enable)
 208{
 209	if (enable) {
 210		uap->curregs[1] |= INT_ALL_Rx | TxINT_ENAB;
 211		if (!ZS_IS_EXTCLK(uap))
 212			uap->curregs[1] |= EXT_INT_ENAB;
 213	} else {
 214		uap->curregs[1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
 215	}
 216	write_zsreg(uap, R1, uap->curregs[1]);
 217}
 218
 219static bool pmz_receive_chars(struct uart_pmac_port *uap)
 220{
 221	struct tty_port *port;
 222	unsigned char ch, r1, drop, flag;
 223	int loops = 0;
 224
 225	/* Sanity check, make sure the old bug is no longer happening */
 226	if (uap->port.state == NULL) {
 227		WARN_ON(1);
 228		(void)read_zsdata(uap);
 229		return false;
 230	}
 231	port = &uap->port.state->port;
 232
 233	while (1) {
 
 234		drop = 0;
 235
 236		r1 = read_zsreg(uap, R1);
 237		ch = read_zsdata(uap);
 238
 239		if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
 240			write_zsreg(uap, R0, ERR_RES);
 241			zssync(uap);
 242		}
 243
 244		ch &= uap->parity_mask;
 245		if (ch == 0 && uap->flags & PMACZILOG_FLAG_BREAK) {
 246			uap->flags &= ~PMACZILOG_FLAG_BREAK;
 247		}
 248
 249#if defined(CONFIG_MAGIC_SYSRQ) && defined(CONFIG_SERIAL_CORE_CONSOLE)
 250#ifdef USE_CTRL_O_SYSRQ
 251		/* Handle the SysRq ^O Hack */
 252		if (ch == '\x0f') {
 253			uap->port.sysrq = jiffies + HZ*5;
 254			goto next_char;
 255		}
 256#endif /* USE_CTRL_O_SYSRQ */
 257		if (uap->port.sysrq) {
 258			int swallow;
 259			spin_unlock(&uap->port.lock);
 260			swallow = uart_handle_sysrq_char(&uap->port, ch);
 261			spin_lock(&uap->port.lock);
 262			if (swallow)
 263				goto next_char;
 264		}
 265#endif /* CONFIG_MAGIC_SYSRQ && CONFIG_SERIAL_CORE_CONSOLE */
 266
 267		/* A real serial line, record the character and status.  */
 268		if (drop)
 269			goto next_char;
 270
 271		flag = TTY_NORMAL;
 272		uap->port.icount.rx++;
 273
 274		if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR | BRK_ABRT)) {
 
 275			if (r1 & BRK_ABRT) {
 276				pmz_debug("pmz: got break !\n");
 277				r1 &= ~(PAR_ERR | CRC_ERR);
 278				uap->port.icount.brk++;
 279				if (uart_handle_break(&uap->port))
 280					goto next_char;
 281			}
 282			else if (r1 & PAR_ERR)
 283				uap->port.icount.parity++;
 284			else if (r1 & CRC_ERR)
 285				uap->port.icount.frame++;
 286			if (r1 & Rx_OVR)
 287				uap->port.icount.overrun++;
 288			r1 &= uap->port.read_status_mask;
 289			if (r1 & BRK_ABRT)
 290				flag = TTY_BREAK;
 291			else if (r1 & PAR_ERR)
 292				flag = TTY_PARITY;
 293			else if (r1 & CRC_ERR)
 294				flag = TTY_FRAME;
 295		}
 296
 297		if (uap->port.ignore_status_mask == 0xff ||
 298		    (r1 & uap->port.ignore_status_mask) == 0) {
 299			tty_insert_flip_char(port, ch, flag);
 300		}
 301		if (r1 & Rx_OVR)
 302			tty_insert_flip_char(port, 0, TTY_OVERRUN);
 303	next_char:
 304		/* We can get stuck in an infinite loop getting char 0 when the
 305		 * line is in a wrong HW state, we break that here.
 306		 * When that happens, I disable the receive side of the driver.
 307		 * Note that what I've been experiencing is a real irq loop where
 308		 * I'm getting flooded regardless of the actual port speed.
 309		 * Something strange is going on with the HW
 310		 */
 311		if ((++loops) > 1000)
 312			goto flood;
 313		ch = read_zsreg(uap, R0);
 314		if (!(ch & Rx_CH_AV))
 315			break;
 316	}
 317
 318	return true;
 319 flood:
 320	pmz_interrupt_control(uap, 0);
 321	pmz_error("pmz: rx irq flood !\n");
 322	return true;
 323}
 324
 325static void pmz_status_handle(struct uart_pmac_port *uap)
 326{
 327	unsigned char status;
 328
 329	status = read_zsreg(uap, R0);
 330	write_zsreg(uap, R0, RES_EXT_INT);
 331	zssync(uap);
 332
 333	if (ZS_IS_OPEN(uap) && ZS_WANTS_MODEM_STATUS(uap)) {
 334		if (status & SYNC_HUNT)
 335			uap->port.icount.dsr++;
 336
 337		/* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
 338		 * But it does not tell us which bit has changed, we have to keep
 339		 * track of this ourselves.
 340		 * The CTS input is inverted for some reason.  -- paulus
 341		 */
 342		if ((status ^ uap->prev_status) & DCD)
 343			uart_handle_dcd_change(&uap->port,
 344					       (status & DCD));
 345		if ((status ^ uap->prev_status) & CTS)
 346			uart_handle_cts_change(&uap->port,
 347					       !(status & CTS));
 348
 349		wake_up_interruptible(&uap->port.state->port.delta_msr_wait);
 350	}
 351
 352	if (status & BRK_ABRT)
 353		uap->flags |= PMACZILOG_FLAG_BREAK;
 354
 355	uap->prev_status = status;
 356}
 357
 358static void pmz_transmit_chars(struct uart_pmac_port *uap)
 359{
 360	struct circ_buf *xmit;
 361
 362	if (ZS_IS_CONS(uap)) {
 363		unsigned char status = read_zsreg(uap, R0);
 364
 365		/* TX still busy?  Just wait for the next TX done interrupt.
 366		 *
 367		 * It can occur because of how we do serial console writes.  It would
 368		 * be nice to transmit console writes just like we normally would for
 369		 * a TTY line. (ie. buffered and TX interrupt driven).  That is not
 370		 * easy because console writes cannot sleep.  One solution might be
 371		 * to poll on enough port->xmit space becoming free.  -DaveM
 372		 */
 373		if (!(status & Tx_BUF_EMP))
 374			return;
 375	}
 376
 377	uap->flags &= ~PMACZILOG_FLAG_TX_ACTIVE;
 378
 379	if (ZS_REGS_HELD(uap)) {
 380		pmz_load_zsregs(uap, uap->curregs);
 381		uap->flags &= ~PMACZILOG_FLAG_REGS_HELD;
 382	}
 383
 384	if (ZS_TX_STOPPED(uap)) {
 385		uap->flags &= ~PMACZILOG_FLAG_TX_STOPPED;
 386		goto ack_tx_int;
 387	}
 388
 389	/* Under some circumstances, we see interrupts reported for
 390	 * a closed channel. The interrupt mask in R1 is clear, but
 391	 * R3 still signals the interrupts and we see them when taking
 392	 * an interrupt for the other channel (this could be a qemu
 393	 * bug but since the ESCC doc doesn't specify precsiely whether
 394	 * R3 interrup status bits are masked by R1 interrupt enable
 395	 * bits, better safe than sorry). --BenH.
 396	 */
 397	if (!ZS_IS_OPEN(uap))
 398		goto ack_tx_int;
 399
 400	if (uap->port.x_char) {
 401		uap->flags |= PMACZILOG_FLAG_TX_ACTIVE;
 402		write_zsdata(uap, uap->port.x_char);
 403		zssync(uap);
 404		uap->port.icount.tx++;
 405		uap->port.x_char = 0;
 406		return;
 407	}
 408
 409	if (uap->port.state == NULL)
 410		goto ack_tx_int;
 411	xmit = &uap->port.state->xmit;
 412	if (uart_circ_empty(xmit)) {
 413		uart_write_wakeup(&uap->port);
 414		goto ack_tx_int;
 415	}
 416	if (uart_tx_stopped(&uap->port))
 417		goto ack_tx_int;
 418
 419	uap->flags |= PMACZILOG_FLAG_TX_ACTIVE;
 420	write_zsdata(uap, xmit->buf[xmit->tail]);
 421	zssync(uap);
 422
 423	xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 424	uap->port.icount.tx++;
 425
 426	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 427		uart_write_wakeup(&uap->port);
 428
 429	return;
 430
 431ack_tx_int:
 432	write_zsreg(uap, R0, RES_Tx_P);
 433	zssync(uap);
 434}
 435
 436/* Hrm... we register that twice, fixme later.... */
 437static irqreturn_t pmz_interrupt(int irq, void *dev_id)
 438{
 439	struct uart_pmac_port *uap = dev_id;
 440	struct uart_pmac_port *uap_a;
 441	struct uart_pmac_port *uap_b;
 442	int rc = IRQ_NONE;
 443	bool push;
 444	u8 r3;
 445
 446	uap_a = pmz_get_port_A(uap);
 447	uap_b = uap_a->mate;
 448
 449	spin_lock(&uap_a->port.lock);
 450	r3 = read_zsreg(uap_a, R3);
 451
 452#ifdef DEBUG_HARD
 453	pmz_debug("irq, r3: %x\n", r3);
 454#endif
 455	/* Channel A */
 456	push = false;
 457	if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
 458		if (!ZS_IS_OPEN(uap_a)) {
 459			pmz_debug("ChanA interrupt while not open !\n");
 460			goto skip_a;
 461		}
 462		write_zsreg(uap_a, R0, RES_H_IUS);
 463		zssync(uap_a);		
 464		if (r3 & CHAEXT)
 465			pmz_status_handle(uap_a);
 466		if (r3 & CHARxIP)
 467			push = pmz_receive_chars(uap_a);
 468		if (r3 & CHATxIP)
 469			pmz_transmit_chars(uap_a);
 470		rc = IRQ_HANDLED;
 471	}
 472 skip_a:
 473	spin_unlock(&uap_a->port.lock);
 474	if (push)
 475		tty_flip_buffer_push(&uap->port.state->port);
 476
 477	if (!uap_b)
 478		goto out;
 479
 480	spin_lock(&uap_b->port.lock);
 481	push = false;
 482	if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
 483		if (!ZS_IS_OPEN(uap_b)) {
 484			pmz_debug("ChanB interrupt while not open !\n");
 485			goto skip_b;
 486		}
 487		write_zsreg(uap_b, R0, RES_H_IUS);
 488		zssync(uap_b);
 489		if (r3 & CHBEXT)
 490			pmz_status_handle(uap_b);
 491		if (r3 & CHBRxIP)
 492			push = pmz_receive_chars(uap_b);
 493		if (r3 & CHBTxIP)
 494			pmz_transmit_chars(uap_b);
 495		rc = IRQ_HANDLED;
 496	}
 497 skip_b:
 498	spin_unlock(&uap_b->port.lock);
 499	if (push)
 500		tty_flip_buffer_push(&uap->port.state->port);
 501
 502 out:
 503	return rc;
 504}
 505
 506/*
 507 * Peek the status register, lock not held by caller
 508 */
 509static inline u8 pmz_peek_status(struct uart_pmac_port *uap)
 510{
 511	unsigned long flags;
 512	u8 status;
 513	
 514	spin_lock_irqsave(&uap->port.lock, flags);
 515	status = read_zsreg(uap, R0);
 516	spin_unlock_irqrestore(&uap->port.lock, flags);
 517
 518	return status;
 519}
 520
 521/* 
 522 * Check if transmitter is empty
 523 * The port lock is not held.
 524 */
 525static unsigned int pmz_tx_empty(struct uart_port *port)
 526{
 527	unsigned char status;
 528
 529	status = pmz_peek_status(to_pmz(port));
 530	if (status & Tx_BUF_EMP)
 531		return TIOCSER_TEMT;
 532	return 0;
 533}
 534
 535/* 
 536 * Set Modem Control (RTS & DTR) bits
 537 * The port lock is held and interrupts are disabled.
 538 * Note: Shall we really filter out RTS on external ports or
 539 * should that be dealt at higher level only ?
 540 */
 541static void pmz_set_mctrl(struct uart_port *port, unsigned int mctrl)
 542{
 543	struct uart_pmac_port *uap = to_pmz(port);
 544	unsigned char set_bits, clear_bits;
 545
 546        /* Do nothing for irda for now... */
 547	if (ZS_IS_IRDA(uap))
 548		return;
 549	/* We get called during boot with a port not up yet */
 550	if (!(ZS_IS_OPEN(uap) || ZS_IS_CONS(uap)))
 551		return;
 552
 553	set_bits = clear_bits = 0;
 554
 555	if (ZS_IS_INTMODEM(uap)) {
 556		if (mctrl & TIOCM_RTS)
 557			set_bits |= RTS;
 558		else
 559			clear_bits |= RTS;
 560	}
 561	if (mctrl & TIOCM_DTR)
 562		set_bits |= DTR;
 563	else
 564		clear_bits |= DTR;
 565
 566	/* NOTE: Not subject to 'transmitter active' rule.  */ 
 567	uap->curregs[R5] |= set_bits;
 568	uap->curregs[R5] &= ~clear_bits;
 569
 570	write_zsreg(uap, R5, uap->curregs[R5]);
 571	pmz_debug("pmz_set_mctrl: set bits: %x, clear bits: %x -> %x\n",
 572		  set_bits, clear_bits, uap->curregs[R5]);
 573	zssync(uap);
 574}
 575
 576/* 
 577 * Get Modem Control bits (only the input ones, the core will
 578 * or that with a cached value of the control ones)
 579 * The port lock is held and interrupts are disabled.
 580 */
 581static unsigned int pmz_get_mctrl(struct uart_port *port)
 582{
 583	struct uart_pmac_port *uap = to_pmz(port);
 584	unsigned char status;
 585	unsigned int ret;
 586
 587	status = read_zsreg(uap, R0);
 588
 589	ret = 0;
 590	if (status & DCD)
 591		ret |= TIOCM_CAR;
 592	if (status & SYNC_HUNT)
 593		ret |= TIOCM_DSR;
 594	if (!(status & CTS))
 595		ret |= TIOCM_CTS;
 596
 597	return ret;
 598}
 599
 600/* 
 601 * Stop TX side. Dealt like sunzilog at next Tx interrupt,
 602 * though for DMA, we will have to do a bit more.
 603 * The port lock is held and interrupts are disabled.
 604 */
 605static void pmz_stop_tx(struct uart_port *port)
 606{
 607	to_pmz(port)->flags |= PMACZILOG_FLAG_TX_STOPPED;
 608}
 609
 610/* 
 611 * Kick the Tx side.
 612 * The port lock is held and interrupts are disabled.
 613 */
 614static void pmz_start_tx(struct uart_port *port)
 615{
 616	struct uart_pmac_port *uap = to_pmz(port);
 617	unsigned char status;
 618
 619	pmz_debug("pmz: start_tx()\n");
 620
 621	uap->flags |= PMACZILOG_FLAG_TX_ACTIVE;
 622	uap->flags &= ~PMACZILOG_FLAG_TX_STOPPED;
 623
 624	status = read_zsreg(uap, R0);
 625
 626	/* TX busy?  Just wait for the TX done interrupt.  */
 627	if (!(status & Tx_BUF_EMP))
 628		return;
 629
 630	/* Send the first character to jump-start the TX done
 631	 * IRQ sending engine.
 632	 */
 633	if (port->x_char) {
 634		write_zsdata(uap, port->x_char);
 635		zssync(uap);
 636		port->icount.tx++;
 637		port->x_char = 0;
 638	} else {
 639		struct circ_buf *xmit = &port->state->xmit;
 640
 641		if (uart_circ_empty(xmit))
 642			goto out;
 643		write_zsdata(uap, xmit->buf[xmit->tail]);
 644		zssync(uap);
 645		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 646		port->icount.tx++;
 647
 648		if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 649			uart_write_wakeup(&uap->port);
 650	}
 651 out:
 652	pmz_debug("pmz: start_tx() done.\n");
 653}
 654
 655/* 
 656 * Stop Rx side, basically disable emitting of
 657 * Rx interrupts on the port. We don't disable the rx
 658 * side of the chip proper though
 659 * The port lock is held.
 660 */
 661static void pmz_stop_rx(struct uart_port *port)
 662{
 663	struct uart_pmac_port *uap = to_pmz(port);
 664
 665	pmz_debug("pmz: stop_rx()()\n");
 666
 667	/* Disable all RX interrupts.  */
 668	uap->curregs[R1] &= ~RxINT_MASK;
 669	pmz_maybe_update_regs(uap);
 670
 671	pmz_debug("pmz: stop_rx() done.\n");
 672}
 673
 674/* 
 675 * Enable modem status change interrupts
 676 * The port lock is held.
 677 */
 678static void pmz_enable_ms(struct uart_port *port)
 679{
 680	struct uart_pmac_port *uap = to_pmz(port);
 681	unsigned char new_reg;
 682
 683	if (ZS_IS_IRDA(uap))
 684		return;
 685	new_reg = uap->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
 686	if (new_reg != uap->curregs[R15]) {
 687		uap->curregs[R15] = new_reg;
 688
 689		/* NOTE: Not subject to 'transmitter active' rule. */
 690		write_zsreg(uap, R15, uap->curregs[R15]);
 691	}
 692}
 693
 694/* 
 695 * Control break state emission
 696 * The port lock is not held.
 697 */
 698static void pmz_break_ctl(struct uart_port *port, int break_state)
 699{
 700	struct uart_pmac_port *uap = to_pmz(port);
 701	unsigned char set_bits, clear_bits, new_reg;
 702	unsigned long flags;
 703
 704	set_bits = clear_bits = 0;
 705
 706	if (break_state)
 707		set_bits |= SND_BRK;
 708	else
 709		clear_bits |= SND_BRK;
 710
 711	spin_lock_irqsave(&port->lock, flags);
 712
 713	new_reg = (uap->curregs[R5] | set_bits) & ~clear_bits;
 714	if (new_reg != uap->curregs[R5]) {
 715		uap->curregs[R5] = new_reg;
 716		write_zsreg(uap, R5, uap->curregs[R5]);
 717	}
 718
 719	spin_unlock_irqrestore(&port->lock, flags);
 720}
 721
 722#ifdef CONFIG_PPC_PMAC
 723
 724/*
 725 * Turn power on or off to the SCC and associated stuff
 726 * (port drivers, modem, IR port, etc.)
 727 * Returns the number of milliseconds we should wait before
 728 * trying to use the port.
 729 */
 730static int pmz_set_scc_power(struct uart_pmac_port *uap, int state)
 731{
 732	int delay = 0;
 733	int rc;
 734
 735	if (state) {
 736		rc = pmac_call_feature(
 737			PMAC_FTR_SCC_ENABLE, uap->node, uap->port_type, 1);
 738		pmz_debug("port power on result: %d\n", rc);
 739		if (ZS_IS_INTMODEM(uap)) {
 740			rc = pmac_call_feature(
 741				PMAC_FTR_MODEM_ENABLE, uap->node, 0, 1);
 742			delay = 2500;	/* wait for 2.5s before using */
 743			pmz_debug("modem power result: %d\n", rc);
 744		}
 745	} else {
 746		/* TODO: Make that depend on a timer, don't power down
 747		 * immediately
 748		 */
 749		if (ZS_IS_INTMODEM(uap)) {
 750			rc = pmac_call_feature(
 751				PMAC_FTR_MODEM_ENABLE, uap->node, 0, 0);
 752			pmz_debug("port power off result: %d\n", rc);
 753		}
 754		pmac_call_feature(PMAC_FTR_SCC_ENABLE, uap->node, uap->port_type, 0);
 755	}
 756	return delay;
 757}
 758
 759#else
 760
 761static int pmz_set_scc_power(struct uart_pmac_port *uap, int state)
 762{
 763	return 0;
 764}
 765
 766#endif /* !CONFIG_PPC_PMAC */
 767
 768/*
 769 * FixZeroBug....Works around a bug in the SCC receiving channel.
 770 * Inspired from Darwin code, 15 Sept. 2000  -DanM
 771 *
 772 * The following sequence prevents a problem that is seen with O'Hare ASICs
 773 * (most versions -- also with some Heathrow and Hydra ASICs) where a zero
 774 * at the input to the receiver becomes 'stuck' and locks up the receiver.
 775 * This problem can occur as a result of a zero bit at the receiver input
 776 * coincident with any of the following events:
 777 *
 778 *	The SCC is initialized (hardware or software).
 779 *	A framing error is detected.
 780 *	The clocking option changes from synchronous or X1 asynchronous
 781 *		clocking to X16, X32, or X64 asynchronous clocking.
 782 *	The decoding mode is changed among NRZ, NRZI, FM0, or FM1.
 783 *
 784 * This workaround attempts to recover from the lockup condition by placing
 785 * the SCC in synchronous loopback mode with a fast clock before programming
 786 * any of the asynchronous modes.
 787 */
 788static void pmz_fix_zero_bug_scc(struct uart_pmac_port *uap)
 789{
 790	write_zsreg(uap, 9, ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB);
 791	zssync(uap);
 792	udelay(10);
 793	write_zsreg(uap, 9, (ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB) | NV);
 794	zssync(uap);
 795
 796	write_zsreg(uap, 4, X1CLK | MONSYNC);
 797	write_zsreg(uap, 3, Rx8);
 798	write_zsreg(uap, 5, Tx8 | RTS);
 799	write_zsreg(uap, 9, NV);	/* Didn't we already do this? */
 800	write_zsreg(uap, 11, RCBR | TCBR);
 801	write_zsreg(uap, 12, 0);
 802	write_zsreg(uap, 13, 0);
 803	write_zsreg(uap, 14, (LOOPBAK | BRSRC));
 804	write_zsreg(uap, 14, (LOOPBAK | BRSRC | BRENAB));
 805	write_zsreg(uap, 3, Rx8 | RxENABLE);
 806	write_zsreg(uap, 0, RES_EXT_INT);
 807	write_zsreg(uap, 0, RES_EXT_INT);
 808	write_zsreg(uap, 0, RES_EXT_INT);	/* to kill some time */
 809
 810	/* The channel should be OK now, but it is probably receiving
 811	 * loopback garbage.
 812	 * Switch to asynchronous mode, disable the receiver,
 813	 * and discard everything in the receive buffer.
 814	 */
 815	write_zsreg(uap, 9, NV);
 816	write_zsreg(uap, 4, X16CLK | SB_MASK);
 817	write_zsreg(uap, 3, Rx8);
 818
 819	while (read_zsreg(uap, 0) & Rx_CH_AV) {
 820		(void)read_zsreg(uap, 8);
 821		write_zsreg(uap, 0, RES_EXT_INT);
 822		write_zsreg(uap, 0, ERR_RES);
 823	}
 824}
 825
 826/*
 827 * Real startup routine, powers up the hardware and sets up
 828 * the SCC. Returns a delay in ms where you need to wait before
 829 * actually using the port, this is typically the internal modem
 830 * powerup delay. This routine expect the lock to be taken.
 831 */
 832static int __pmz_startup(struct uart_pmac_port *uap)
 833{
 834	int pwr_delay = 0;
 835
 836	memset(&uap->curregs, 0, sizeof(uap->curregs));
 837
 838	/* Power up the SCC & underlying hardware (modem/irda) */
 839	pwr_delay = pmz_set_scc_power(uap, 1);
 840
 841	/* Nice buggy HW ... */
 842	pmz_fix_zero_bug_scc(uap);
 843
 844	/* Reset the channel */
 845	uap->curregs[R9] = 0;
 846	write_zsreg(uap, 9, ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB);
 847	zssync(uap);
 848	udelay(10);
 849	write_zsreg(uap, 9, 0);
 850	zssync(uap);
 851
 852	/* Clear the interrupt registers */
 853	write_zsreg(uap, R1, 0);
 854	write_zsreg(uap, R0, ERR_RES);
 855	write_zsreg(uap, R0, ERR_RES);
 856	write_zsreg(uap, R0, RES_H_IUS);
 857	write_zsreg(uap, R0, RES_H_IUS);
 858
 859	/* Setup some valid baud rate */
 860	uap->curregs[R4] = X16CLK | SB1;
 861	uap->curregs[R3] = Rx8;
 862	uap->curregs[R5] = Tx8 | RTS;
 863	if (!ZS_IS_IRDA(uap))
 864		uap->curregs[R5] |= DTR;
 865	uap->curregs[R12] = 0;
 866	uap->curregs[R13] = 0;
 867	uap->curregs[R14] = BRENAB;
 868
 869	/* Clear handshaking, enable BREAK interrupts */
 870	uap->curregs[R15] = BRKIE;
 871
 872	/* Master interrupt enable */
 873	uap->curregs[R9] |= NV | MIE;
 874
 875	pmz_load_zsregs(uap, uap->curregs);
 876
 877	/* Enable receiver and transmitter.  */
 878	write_zsreg(uap, R3, uap->curregs[R3] |= RxENABLE);
 879	write_zsreg(uap, R5, uap->curregs[R5] |= TxENABLE);
 880
 881	/* Remember status for DCD/CTS changes */
 882	uap->prev_status = read_zsreg(uap, R0);
 883
 884	return pwr_delay;
 885}
 886
 887static void pmz_irda_reset(struct uart_pmac_port *uap)
 888{
 889	unsigned long flags;
 890
 891	spin_lock_irqsave(&uap->port.lock, flags);
 892	uap->curregs[R5] |= DTR;
 893	write_zsreg(uap, R5, uap->curregs[R5]);
 894	zssync(uap);
 895	spin_unlock_irqrestore(&uap->port.lock, flags);
 896	msleep(110);
 897
 898	spin_lock_irqsave(&uap->port.lock, flags);
 899	uap->curregs[R5] &= ~DTR;
 900	write_zsreg(uap, R5, uap->curregs[R5]);
 901	zssync(uap);
 902	spin_unlock_irqrestore(&uap->port.lock, flags);
 903	msleep(10);
 904}
 905
 906/*
 907 * This is the "normal" startup routine, using the above one
 908 * wrapped with the lock and doing a schedule delay
 909 */
 910static int pmz_startup(struct uart_port *port)
 911{
 912	struct uart_pmac_port *uap = to_pmz(port);
 913	unsigned long flags;
 914	int pwr_delay = 0;
 915
 916	pmz_debug("pmz: startup()\n");
 917
 918	uap->flags |= PMACZILOG_FLAG_IS_OPEN;
 919
 920	/* A console is never powered down. Else, power up and
 921	 * initialize the chip
 922	 */
 923	if (!ZS_IS_CONS(uap)) {
 924		spin_lock_irqsave(&port->lock, flags);
 925		pwr_delay = __pmz_startup(uap);
 926		spin_unlock_irqrestore(&port->lock, flags);
 927	}	
 928	sprintf(uap->irq_name, PMACZILOG_NAME"%d", uap->port.line);
 929	if (request_irq(uap->port.irq, pmz_interrupt, IRQF_SHARED,
 930			uap->irq_name, uap)) {
 931		pmz_error("Unable to register zs interrupt handler.\n");
 932		pmz_set_scc_power(uap, 0);
 933		return -ENXIO;
 934	}
 935
 936	/* Right now, we deal with delay by blocking here, I'll be
 937	 * smarter later on
 938	 */
 939	if (pwr_delay != 0) {
 940		pmz_debug("pmz: delaying %d ms\n", pwr_delay);
 941		msleep(pwr_delay);
 942	}
 943
 944	/* IrDA reset is done now */
 945	if (ZS_IS_IRDA(uap))
 946		pmz_irda_reset(uap);
 947
 948	/* Enable interrupt requests for the channel */
 949	spin_lock_irqsave(&port->lock, flags);
 950	pmz_interrupt_control(uap, 1);
 951	spin_unlock_irqrestore(&port->lock, flags);
 952
 953	pmz_debug("pmz: startup() done.\n");
 954
 955	return 0;
 956}
 957
 958static void pmz_shutdown(struct uart_port *port)
 959{
 960	struct uart_pmac_port *uap = to_pmz(port);
 961	unsigned long flags;
 962
 963	pmz_debug("pmz: shutdown()\n");
 964
 965	spin_lock_irqsave(&port->lock, flags);
 966
 967	/* Disable interrupt requests for the channel */
 968	pmz_interrupt_control(uap, 0);
 969
 970	if (!ZS_IS_CONS(uap)) {
 971		/* Disable receiver and transmitter */
 972		uap->curregs[R3] &= ~RxENABLE;
 973		uap->curregs[R5] &= ~TxENABLE;
 974
 975		/* Disable break assertion */
 976		uap->curregs[R5] &= ~SND_BRK;
 977		pmz_maybe_update_regs(uap);
 978	}
 979
 980	spin_unlock_irqrestore(&port->lock, flags);
 981
 982	/* Release interrupt handler */
 983	free_irq(uap->port.irq, uap);
 984
 985	spin_lock_irqsave(&port->lock, flags);
 986
 987	uap->flags &= ~PMACZILOG_FLAG_IS_OPEN;
 988
 989	if (!ZS_IS_CONS(uap))
 990		pmz_set_scc_power(uap, 0);	/* Shut the chip down */
 991
 992	spin_unlock_irqrestore(&port->lock, flags);
 993
 994	pmz_debug("pmz: shutdown() done.\n");
 995}
 996
 997/* Shared by TTY driver and serial console setup.  The port lock is held
 998 * and local interrupts are disabled.
 999 */
1000static void pmz_convert_to_zs(struct uart_pmac_port *uap, unsigned int cflag,
1001			      unsigned int iflag, unsigned long baud)
1002{
1003	int brg;
1004
1005	/* Switch to external clocking for IrDA high clock rates. That
1006	 * code could be re-used for Midi interfaces with different
1007	 * multipliers
1008	 */
1009	if (baud >= 115200 && ZS_IS_IRDA(uap)) {
1010		uap->curregs[R4] = X1CLK;
1011		uap->curregs[R11] = RCTRxCP | TCTRxCP;
1012		uap->curregs[R14] = 0; /* BRG off */
1013		uap->curregs[R12] = 0;
1014		uap->curregs[R13] = 0;
1015		uap->flags |= PMACZILOG_FLAG_IS_EXTCLK;
1016	} else {
1017		switch (baud) {
1018		case ZS_CLOCK/16:	/* 230400 */
1019			uap->curregs[R4] = X16CLK;
1020			uap->curregs[R11] = 0;
1021			uap->curregs[R14] = 0;
1022			break;
1023		case ZS_CLOCK/32:	/* 115200 */
1024			uap->curregs[R4] = X32CLK;
1025			uap->curregs[R11] = 0;
1026			uap->curregs[R14] = 0;
1027			break;
1028		default:
1029			uap->curregs[R4] = X16CLK;
1030			uap->curregs[R11] = TCBR | RCBR;
1031			brg = BPS_TO_BRG(baud, ZS_CLOCK / 16);
1032			uap->curregs[R12] = (brg & 255);
1033			uap->curregs[R13] = ((brg >> 8) & 255);
1034			uap->curregs[R14] = BRENAB;
1035		}
1036		uap->flags &= ~PMACZILOG_FLAG_IS_EXTCLK;
1037	}
1038
1039	/* Character size, stop bits, and parity. */
1040	uap->curregs[3] &= ~RxN_MASK;
1041	uap->curregs[5] &= ~TxN_MASK;
1042
1043	switch (cflag & CSIZE) {
1044	case CS5:
1045		uap->curregs[3] |= Rx5;
1046		uap->curregs[5] |= Tx5;
1047		uap->parity_mask = 0x1f;
1048		break;
1049	case CS6:
1050		uap->curregs[3] |= Rx6;
1051		uap->curregs[5] |= Tx6;
1052		uap->parity_mask = 0x3f;
1053		break;
1054	case CS7:
1055		uap->curregs[3] |= Rx7;
1056		uap->curregs[5] |= Tx7;
1057		uap->parity_mask = 0x7f;
1058		break;
1059	case CS8:
1060	default:
1061		uap->curregs[3] |= Rx8;
1062		uap->curregs[5] |= Tx8;
1063		uap->parity_mask = 0xff;
1064		break;
1065	}
1066	uap->curregs[4] &= ~(SB_MASK);
1067	if (cflag & CSTOPB)
1068		uap->curregs[4] |= SB2;
1069	else
1070		uap->curregs[4] |= SB1;
1071	if (cflag & PARENB)
1072		uap->curregs[4] |= PAR_ENAB;
1073	else
1074		uap->curregs[4] &= ~PAR_ENAB;
1075	if (!(cflag & PARODD))
1076		uap->curregs[4] |= PAR_EVEN;
1077	else
1078		uap->curregs[4] &= ~PAR_EVEN;
1079
1080	uap->port.read_status_mask = Rx_OVR;
1081	if (iflag & INPCK)
1082		uap->port.read_status_mask |= CRC_ERR | PAR_ERR;
1083	if (iflag & (IGNBRK | BRKINT | PARMRK))
1084		uap->port.read_status_mask |= BRK_ABRT;
1085
1086	uap->port.ignore_status_mask = 0;
1087	if (iflag & IGNPAR)
1088		uap->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
1089	if (iflag & IGNBRK) {
1090		uap->port.ignore_status_mask |= BRK_ABRT;
1091		if (iflag & IGNPAR)
1092			uap->port.ignore_status_mask |= Rx_OVR;
1093	}
1094
1095	if ((cflag & CREAD) == 0)
1096		uap->port.ignore_status_mask = 0xff;
1097}
1098
1099
1100/*
1101 * Set the irda codec on the imac to the specified baud rate.
1102 */
1103static void pmz_irda_setup(struct uart_pmac_port *uap, unsigned long *baud)
1104{
1105	u8 cmdbyte;
1106	int t, version;
1107
1108	switch (*baud) {
1109	/* SIR modes */
1110	case 2400:
1111		cmdbyte = 0x53;
1112		break;
1113	case 4800:
1114		cmdbyte = 0x52;
1115		break;
1116	case 9600:
1117		cmdbyte = 0x51;
1118		break;
1119	case 19200:
1120		cmdbyte = 0x50;
1121		break;
1122	case 38400:
1123		cmdbyte = 0x4f;
1124		break;
1125	case 57600:
1126		cmdbyte = 0x4e;
1127		break;
1128	case 115200:
1129		cmdbyte = 0x4d;
1130		break;
1131	/* The FIR modes aren't really supported at this point, how
1132	 * do we select the speed ? via the FCR on KeyLargo ?
1133	 */
1134	case 1152000:
1135		cmdbyte = 0;
1136		break;
1137	case 4000000:
1138		cmdbyte = 0;
1139		break;
1140	default: /* 9600 */
1141		cmdbyte = 0x51;
1142		*baud = 9600;
1143		break;
1144	}
1145
1146	/* Wait for transmitter to drain */
1147	t = 10000;
1148	while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0
1149	       || (read_zsreg(uap, R1) & ALL_SNT) == 0) {
1150		if (--t <= 0) {
1151			pmz_error("transmitter didn't drain\n");
1152			return;
1153		}
1154		udelay(10);
1155	}
1156
1157	/* Drain the receiver too */
1158	t = 100;
1159	(void)read_zsdata(uap);
1160	(void)read_zsdata(uap);
1161	(void)read_zsdata(uap);
1162	mdelay(10);
1163	while (read_zsreg(uap, R0) & Rx_CH_AV) {
1164		read_zsdata(uap);
1165		mdelay(10);
1166		if (--t <= 0) {
1167			pmz_error("receiver didn't drain\n");
1168			return;
1169		}
1170	}
1171
1172	/* Switch to command mode */
1173	uap->curregs[R5] |= DTR;
1174	write_zsreg(uap, R5, uap->curregs[R5]);
1175	zssync(uap);
1176	mdelay(1);
1177
1178	/* Switch SCC to 19200 */
1179	pmz_convert_to_zs(uap, CS8, 0, 19200);		
1180	pmz_load_zsregs(uap, uap->curregs);
1181	mdelay(1);
1182
1183	/* Write get_version command byte */
1184	write_zsdata(uap, 1);
1185	t = 5000;
1186	while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) {
1187		if (--t <= 0) {
1188			pmz_error("irda_setup timed out on get_version byte\n");
1189			goto out;
1190		}
1191		udelay(10);
1192	}
1193	version = read_zsdata(uap);
1194
1195	if (version < 4) {
1196		pmz_info("IrDA: dongle version %d not supported\n", version);
1197		goto out;
1198	}
1199
1200	/* Send speed mode */
1201	write_zsdata(uap, cmdbyte);
1202	t = 5000;
1203	while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) {
1204		if (--t <= 0) {
1205			pmz_error("irda_setup timed out on speed mode byte\n");
1206			goto out;
1207		}
1208		udelay(10);
1209	}
1210	t = read_zsdata(uap);
1211	if (t != cmdbyte)
1212		pmz_error("irda_setup speed mode byte = %x (%x)\n", t, cmdbyte);
1213
1214	pmz_info("IrDA setup for %ld bps, dongle version: %d\n",
1215		 *baud, version);
1216
1217	(void)read_zsdata(uap);
1218	(void)read_zsdata(uap);
1219	(void)read_zsdata(uap);
1220
1221 out:
1222	/* Switch back to data mode */
1223	uap->curregs[R5] &= ~DTR;
1224	write_zsreg(uap, R5, uap->curregs[R5]);
1225	zssync(uap);
1226
1227	(void)read_zsdata(uap);
1228	(void)read_zsdata(uap);
1229	(void)read_zsdata(uap);
1230}
1231
1232
1233static void __pmz_set_termios(struct uart_port *port, struct ktermios *termios,
1234			      struct ktermios *old)
1235{
1236	struct uart_pmac_port *uap = to_pmz(port);
1237	unsigned long baud;
1238
1239	pmz_debug("pmz: set_termios()\n");
1240
1241	memcpy(&uap->termios_cache, termios, sizeof(struct ktermios));
1242
1243	/* XXX Check which revs of machines actually allow 1 and 4Mb speeds
1244	 * on the IR dongle. Note that the IRTTY driver currently doesn't know
1245	 * about the FIR mode and high speed modes. So these are unused. For
1246	 * implementing proper support for these, we should probably add some
1247	 * DMA as well, at least on the Rx side, which isn't a simple thing
1248	 * at this point.
1249	 */
1250	if (ZS_IS_IRDA(uap)) {
1251		/* Calc baud rate */
1252		baud = uart_get_baud_rate(port, termios, old, 1200, 4000000);
1253		pmz_debug("pmz: switch IRDA to %ld bauds\n", baud);
1254		/* Cet the irda codec to the right rate */
1255		pmz_irda_setup(uap, &baud);
1256		/* Set final baud rate */
1257		pmz_convert_to_zs(uap, termios->c_cflag, termios->c_iflag, baud);
1258		pmz_load_zsregs(uap, uap->curregs);
1259		zssync(uap);
1260	} else {
1261		baud = uart_get_baud_rate(port, termios, old, 1200, 230400);
1262		pmz_convert_to_zs(uap, termios->c_cflag, termios->c_iflag, baud);
1263		/* Make sure modem status interrupts are correctly configured */
1264		if (UART_ENABLE_MS(&uap->port, termios->c_cflag)) {
1265			uap->curregs[R15] |= DCDIE | SYNCIE | CTSIE;
1266			uap->flags |= PMACZILOG_FLAG_MODEM_STATUS;
1267		} else {
1268			uap->curregs[R15] &= ~(DCDIE | SYNCIE | CTSIE);
1269			uap->flags &= ~PMACZILOG_FLAG_MODEM_STATUS;
1270		}
1271
1272		/* Load registers to the chip */
1273		pmz_maybe_update_regs(uap);
1274	}
1275	uart_update_timeout(port, termios->c_cflag, baud);
1276
1277	pmz_debug("pmz: set_termios() done.\n");
1278}
1279
1280/* The port lock is not held.  */
1281static void pmz_set_termios(struct uart_port *port, struct ktermios *termios,
1282			    struct ktermios *old)
1283{
1284	struct uart_pmac_port *uap = to_pmz(port);
1285	unsigned long flags;
1286
1287	spin_lock_irqsave(&port->lock, flags);	
1288
1289	/* Disable IRQs on the port */
1290	pmz_interrupt_control(uap, 0);
1291
1292	/* Setup new port configuration */
1293	__pmz_set_termios(port, termios, old);
1294
1295	/* Re-enable IRQs on the port */
1296	if (ZS_IS_OPEN(uap))
1297		pmz_interrupt_control(uap, 1);
1298
1299	spin_unlock_irqrestore(&port->lock, flags);
1300}
1301
1302static const char *pmz_type(struct uart_port *port)
1303{
1304	struct uart_pmac_port *uap = to_pmz(port);
1305
1306	if (ZS_IS_IRDA(uap))
1307		return "Z85c30 ESCC - Infrared port";
1308	else if (ZS_IS_INTMODEM(uap))
1309		return "Z85c30 ESCC - Internal modem";
1310	return "Z85c30 ESCC - Serial port";
1311}
1312
1313/* We do not request/release mappings of the registers here, this
1314 * happens at early serial probe time.
1315 */
1316static void pmz_release_port(struct uart_port *port)
1317{
1318}
1319
1320static int pmz_request_port(struct uart_port *port)
1321{
1322	return 0;
1323}
1324
1325/* These do not need to do anything interesting either.  */
1326static void pmz_config_port(struct uart_port *port, int flags)
1327{
1328}
1329
1330/* We do not support letting the user mess with the divisor, IRQ, etc. */
1331static int pmz_verify_port(struct uart_port *port, struct serial_struct *ser)
1332{
1333	return -EINVAL;
1334}
1335
1336#ifdef CONFIG_CONSOLE_POLL
1337
1338static int pmz_poll_get_char(struct uart_port *port)
1339{
1340	struct uart_pmac_port *uap =
1341		container_of(port, struct uart_pmac_port, port);
1342	int tries = 2;
1343
1344	while (tries) {
1345		if ((read_zsreg(uap, R0) & Rx_CH_AV) != 0)
1346			return read_zsdata(uap);
1347		if (tries--)
1348			udelay(5);
1349	}
1350
1351	return NO_POLL_CHAR;
1352}
1353
1354static void pmz_poll_put_char(struct uart_port *port, unsigned char c)
1355{
1356	struct uart_pmac_port *uap =
1357		container_of(port, struct uart_pmac_port, port);
1358
1359	/* Wait for the transmit buffer to empty. */
1360	while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0)
1361		udelay(5);
1362	write_zsdata(uap, c);
1363}
1364
1365#endif /* CONFIG_CONSOLE_POLL */
1366
1367static const struct uart_ops pmz_pops = {
1368	.tx_empty	=	pmz_tx_empty,
1369	.set_mctrl	=	pmz_set_mctrl,
1370	.get_mctrl	=	pmz_get_mctrl,
1371	.stop_tx	=	pmz_stop_tx,
1372	.start_tx	=	pmz_start_tx,
1373	.stop_rx	=	pmz_stop_rx,
1374	.enable_ms	=	pmz_enable_ms,
1375	.break_ctl	=	pmz_break_ctl,
1376	.startup	=	pmz_startup,
1377	.shutdown	=	pmz_shutdown,
1378	.set_termios	=	pmz_set_termios,
1379	.type		=	pmz_type,
1380	.release_port	=	pmz_release_port,
1381	.request_port	=	pmz_request_port,
1382	.config_port	=	pmz_config_port,
1383	.verify_port	=	pmz_verify_port,
1384#ifdef CONFIG_CONSOLE_POLL
1385	.poll_get_char	=	pmz_poll_get_char,
1386	.poll_put_char	=	pmz_poll_put_char,
1387#endif
1388};
1389
1390#ifdef CONFIG_PPC_PMAC
1391
1392/*
1393 * Setup one port structure after probing, HW is down at this point,
1394 * Unlike sunzilog, we don't need to pre-init the spinlock as we don't
1395 * register our console before uart_add_one_port() is called
1396 */
1397static int __init pmz_init_port(struct uart_pmac_port *uap)
1398{
1399	struct device_node *np = uap->node;
1400	const char *conn;
1401	const struct slot_names_prop {
1402		int	count;
1403		char	name[1];
1404	} *slots;
1405	int len;
1406	struct resource r_ports, r_rxdma, r_txdma;
1407
1408	/*
1409	 * Request & map chip registers
1410	 */
1411	if (of_address_to_resource(np, 0, &r_ports))
1412		return -ENODEV;
1413	uap->port.mapbase = r_ports.start;
1414	uap->port.membase = ioremap(uap->port.mapbase, 0x1000);
1415
1416	uap->control_reg = uap->port.membase;
1417	uap->data_reg = uap->control_reg + 0x10;
1418	
1419	/*
1420	 * Request & map DBDMA registers
1421	 */
1422#ifdef HAS_DBDMA
1423	if (of_address_to_resource(np, 1, &r_txdma) == 0 &&
1424	    of_address_to_resource(np, 2, &r_rxdma) == 0)
1425		uap->flags |= PMACZILOG_FLAG_HAS_DMA;
1426#else
1427	memset(&r_txdma, 0, sizeof(struct resource));
1428	memset(&r_rxdma, 0, sizeof(struct resource));
1429#endif	
1430	if (ZS_HAS_DMA(uap)) {
1431		uap->tx_dma_regs = ioremap(r_txdma.start, 0x100);
1432		if (uap->tx_dma_regs == NULL) {	
1433			uap->flags &= ~PMACZILOG_FLAG_HAS_DMA;
1434			goto no_dma;
1435		}
1436		uap->rx_dma_regs = ioremap(r_rxdma.start, 0x100);
1437		if (uap->rx_dma_regs == NULL) {	
1438			iounmap(uap->tx_dma_regs);
1439			uap->tx_dma_regs = NULL;
1440			uap->flags &= ~PMACZILOG_FLAG_HAS_DMA;
1441			goto no_dma;
1442		}
1443		uap->tx_dma_irq = irq_of_parse_and_map(np, 1);
1444		uap->rx_dma_irq = irq_of_parse_and_map(np, 2);
1445	}
1446no_dma:
1447
1448	/*
1449	 * Detect port type
1450	 */
1451	if (of_device_is_compatible(np, "cobalt"))
1452		uap->flags |= PMACZILOG_FLAG_IS_INTMODEM;
1453	conn = of_get_property(np, "AAPL,connector", &len);
1454	if (conn && (strcmp(conn, "infrared") == 0))
1455		uap->flags |= PMACZILOG_FLAG_IS_IRDA;
1456	uap->port_type = PMAC_SCC_ASYNC;
1457	/* 1999 Powerbook G3 has slot-names property instead */
1458	slots = of_get_property(np, "slot-names", &len);
1459	if (slots && slots->count > 0) {
1460		if (strcmp(slots->name, "IrDA") == 0)
1461			uap->flags |= PMACZILOG_FLAG_IS_IRDA;
1462		else if (strcmp(slots->name, "Modem") == 0)
1463			uap->flags |= PMACZILOG_FLAG_IS_INTMODEM;
1464	}
1465	if (ZS_IS_IRDA(uap))
1466		uap->port_type = PMAC_SCC_IRDA;
1467	if (ZS_IS_INTMODEM(uap)) {
1468		struct device_node* i2c_modem =
1469			of_find_node_by_name(NULL, "i2c-modem");
1470		if (i2c_modem) {
1471			const char* mid =
1472				of_get_property(i2c_modem, "modem-id", NULL);
1473			if (mid) switch(*mid) {
1474			case 0x04 :
1475			case 0x05 :
1476			case 0x07 :
1477			case 0x08 :
1478			case 0x0b :
1479			case 0x0c :
1480				uap->port_type = PMAC_SCC_I2S1;
1481			}
1482			printk(KERN_INFO "pmac_zilog: i2c-modem detected, id: %d\n",
1483				mid ? (*mid) : 0);
1484			of_node_put(i2c_modem);
1485		} else {
1486			printk(KERN_INFO "pmac_zilog: serial modem detected\n");
1487		}
1488	}
1489
1490	/*
1491	 * Init remaining bits of "port" structure
1492	 */
1493	uap->port.iotype = UPIO_MEM;
1494	uap->port.irq = irq_of_parse_and_map(np, 0);
1495	uap->port.uartclk = ZS_CLOCK;
1496	uap->port.fifosize = 1;
1497	uap->port.ops = &pmz_pops;
1498	uap->port.type = PORT_PMAC_ZILOG;
1499	uap->port.flags = 0;
1500
1501	/*
1502	 * Fixup for the port on Gatwick for which the device-tree has
1503	 * missing interrupts. Normally, the macio_dev would contain
1504	 * fixed up interrupt info, but we use the device-tree directly
1505	 * here due to early probing so we need the fixup too.
1506	 */
1507	if (uap->port.irq == 0 &&
1508	    np->parent && np->parent->parent &&
1509	    of_device_is_compatible(np->parent->parent, "gatwick")) {
1510		/* IRQs on gatwick are offset by 64 */
1511		uap->port.irq = irq_create_mapping(NULL, 64 + 15);
1512		uap->tx_dma_irq = irq_create_mapping(NULL, 64 + 4);
1513		uap->rx_dma_irq = irq_create_mapping(NULL, 64 + 5);
1514	}
1515
1516	/* Setup some valid baud rate information in the register
1517	 * shadows so we don't write crap there before baud rate is
1518	 * first initialized.
1519	 */
1520	pmz_convert_to_zs(uap, CS8, 0, 9600);
1521
1522	return 0;
1523}
1524
1525/*
1526 * Get rid of a port on module removal
1527 */
1528static void pmz_dispose_port(struct uart_pmac_port *uap)
1529{
1530	struct device_node *np;
1531
1532	np = uap->node;
1533	iounmap(uap->rx_dma_regs);
1534	iounmap(uap->tx_dma_regs);
1535	iounmap(uap->control_reg);
1536	uap->node = NULL;
1537	of_node_put(np);
1538	memset(uap, 0, sizeof(struct uart_pmac_port));
1539}
1540
1541/*
1542 * Called upon match with an escc node in the device-tree.
1543 */
1544static int pmz_attach(struct macio_dev *mdev, const struct of_device_id *match)
1545{
1546	struct uart_pmac_port *uap;
1547	int i;
1548	
1549	/* Iterate the pmz_ports array to find a matching entry
1550	 */
1551	for (i = 0; i < MAX_ZS_PORTS; i++)
1552		if (pmz_ports[i].node == mdev->ofdev.dev.of_node)
1553			break;
1554	if (i >= MAX_ZS_PORTS)
1555		return -ENODEV;
1556
1557
1558	uap = &pmz_ports[i];
1559	uap->dev = mdev;
1560	uap->port.dev = &mdev->ofdev.dev;
1561	dev_set_drvdata(&mdev->ofdev.dev, uap);
1562
1563	/* We still activate the port even when failing to request resources
1564	 * to work around bugs in ancient Apple device-trees
1565	 */
1566	if (macio_request_resources(uap->dev, "pmac_zilog"))
1567		printk(KERN_WARNING "%pOFn: Failed to request resource"
1568		       ", port still active\n",
1569		       uap->node);
1570	else
1571		uap->flags |= PMACZILOG_FLAG_RSRC_REQUESTED;
1572
1573	return uart_add_one_port(&pmz_uart_reg, &uap->port);
1574}
1575
1576/*
1577 * That one should not be called, macio isn't really a hotswap device,
1578 * we don't expect one of those serial ports to go away...
1579 */
1580static int pmz_detach(struct macio_dev *mdev)
1581{
1582	struct uart_pmac_port	*uap = dev_get_drvdata(&mdev->ofdev.dev);
1583	
1584	if (!uap)
1585		return -ENODEV;
1586
1587	uart_remove_one_port(&pmz_uart_reg, &uap->port);
1588
1589	if (uap->flags & PMACZILOG_FLAG_RSRC_REQUESTED) {
1590		macio_release_resources(uap->dev);
1591		uap->flags &= ~PMACZILOG_FLAG_RSRC_REQUESTED;
1592	}
1593	dev_set_drvdata(&mdev->ofdev.dev, NULL);
1594	uap->dev = NULL;
1595	uap->port.dev = NULL;
1596	
1597	return 0;
1598}
1599
1600
1601static int pmz_suspend(struct macio_dev *mdev, pm_message_t pm_state)
1602{
1603	struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev);
1604
1605	if (uap == NULL) {
1606		printk("HRM... pmz_suspend with NULL uap\n");
1607		return 0;
1608	}
1609
1610	uart_suspend_port(&pmz_uart_reg, &uap->port);
1611
1612	return 0;
1613}
1614
1615
1616static int pmz_resume(struct macio_dev *mdev)
1617{
1618	struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev);
1619
1620	if (uap == NULL)
1621		return 0;
1622
1623	uart_resume_port(&pmz_uart_reg, &uap->port);
1624
1625	return 0;
1626}
1627
1628/*
1629 * Probe all ports in the system and build the ports array, we register
1630 * with the serial layer later, so we get a proper struct device which
1631 * allows the tty to attach properly. This is later than it used to be
1632 * but the tty layer really wants it that way.
1633 */
1634static int __init pmz_probe(void)
1635{
1636	struct device_node	*node_p, *node_a, *node_b, *np;
1637	int			count = 0;
1638	int			rc;
1639
1640	/*
1641	 * Find all escc chips in the system
1642	 */
1643	for_each_node_by_name(node_p, "escc") {
1644		/*
1645		 * First get channel A/B node pointers
1646		 * 
1647		 * TODO: Add routines with proper locking to do that...
1648		 */
1649		node_a = node_b = NULL;
1650		for (np = NULL; (np = of_get_next_child(node_p, np)) != NULL;) {
1651			if (of_node_name_prefix(np, "ch-a"))
1652				node_a = of_node_get(np);
1653			else if (of_node_name_prefix(np, "ch-b"))
1654				node_b = of_node_get(np);
1655		}
1656		if (!node_a && !node_b) {
1657			of_node_put(node_a);
1658			of_node_put(node_b);
1659			printk(KERN_ERR "pmac_zilog: missing node %c for escc %pOF\n",
1660				(!node_a) ? 'a' : 'b', node_p);
1661			continue;
1662		}
1663
1664		/*
1665		 * Fill basic fields in the port structures
1666		 */
1667		if (node_b != NULL) {
1668			pmz_ports[count].mate		= &pmz_ports[count+1];
1669			pmz_ports[count+1].mate		= &pmz_ports[count];
1670		}
1671		pmz_ports[count].flags		= PMACZILOG_FLAG_IS_CHANNEL_A;
1672		pmz_ports[count].node		= node_a;
1673		pmz_ports[count+1].node		= node_b;
1674		pmz_ports[count].port.line	= count;
1675		pmz_ports[count+1].port.line	= count+1;
1676
1677		/*
1678		 * Setup the ports for real
1679		 */
1680		rc = pmz_init_port(&pmz_ports[count]);
1681		if (rc == 0 && node_b != NULL)
1682			rc = pmz_init_port(&pmz_ports[count+1]);
1683		if (rc != 0) {
1684			of_node_put(node_a);
1685			of_node_put(node_b);
1686			memset(&pmz_ports[count], 0, sizeof(struct uart_pmac_port));
1687			memset(&pmz_ports[count+1], 0, sizeof(struct uart_pmac_port));
1688			continue;
1689		}
1690		count += 2;
1691	}
1692	pmz_ports_count = count;
1693
1694	return 0;
1695}
1696
1697#else
1698
1699extern struct platform_device scc_a_pdev, scc_b_pdev;
1700
1701static int __init pmz_init_port(struct uart_pmac_port *uap)
1702{
1703	struct resource *r_ports;
1704	int irq;
1705
1706	r_ports = platform_get_resource(uap->pdev, IORESOURCE_MEM, 0);
1707	irq = platform_get_irq(uap->pdev, 0);
1708	if (!r_ports || irq <= 0)
1709		return -ENODEV;
1710
1711	uap->port.mapbase  = r_ports->start;
1712	uap->port.membase  = (unsigned char __iomem *) r_ports->start;
1713	uap->port.iotype   = UPIO_MEM;
1714	uap->port.irq      = irq;
1715	uap->port.uartclk  = ZS_CLOCK;
1716	uap->port.fifosize = 1;
1717	uap->port.ops      = &pmz_pops;
1718	uap->port.type     = PORT_PMAC_ZILOG;
1719	uap->port.flags    = 0;
1720
1721	uap->control_reg   = uap->port.membase;
1722	uap->data_reg      = uap->control_reg + 4;
1723	uap->port_type     = 0;
1724
1725	pmz_convert_to_zs(uap, CS8, 0, 9600);
1726
1727	return 0;
1728}
1729
1730static int __init pmz_probe(void)
1731{
1732	int err;
1733
1734	pmz_ports_count = 0;
1735
1736	pmz_ports[0].port.line = 0;
1737	pmz_ports[0].flags     = PMACZILOG_FLAG_IS_CHANNEL_A;
1738	pmz_ports[0].pdev      = &scc_a_pdev;
1739	err = pmz_init_port(&pmz_ports[0]);
1740	if (err)
1741		return err;
1742	pmz_ports_count++;
1743
1744	pmz_ports[0].mate      = &pmz_ports[1];
1745	pmz_ports[1].mate      = &pmz_ports[0];
1746	pmz_ports[1].port.line = 1;
1747	pmz_ports[1].flags     = 0;
1748	pmz_ports[1].pdev      = &scc_b_pdev;
1749	err = pmz_init_port(&pmz_ports[1]);
1750	if (err)
1751		return err;
1752	pmz_ports_count++;
1753
1754	return 0;
1755}
1756
1757static void pmz_dispose_port(struct uart_pmac_port *uap)
1758{
1759	memset(uap, 0, sizeof(struct uart_pmac_port));
1760}
1761
1762static int __init pmz_attach(struct platform_device *pdev)
1763{
1764	struct uart_pmac_port *uap;
1765	int i;
1766
1767	/* Iterate the pmz_ports array to find a matching entry */
1768	for (i = 0; i < pmz_ports_count; i++)
1769		if (pmz_ports[i].pdev == pdev)
1770			break;
1771	if (i >= pmz_ports_count)
1772		return -ENODEV;
1773
1774	uap = &pmz_ports[i];
1775	uap->port.dev = &pdev->dev;
1776	platform_set_drvdata(pdev, uap);
1777
1778	return uart_add_one_port(&pmz_uart_reg, &uap->port);
1779}
1780
1781static int __exit pmz_detach(struct platform_device *pdev)
1782{
1783	struct uart_pmac_port *uap = platform_get_drvdata(pdev);
1784
1785	if (!uap)
1786		return -ENODEV;
1787
1788	uart_remove_one_port(&pmz_uart_reg, &uap->port);
1789
1790	uap->port.dev = NULL;
1791
1792	return 0;
1793}
1794
1795#endif /* !CONFIG_PPC_PMAC */
1796
1797#ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE
1798
1799static void pmz_console_write(struct console *con, const char *s, unsigned int count);
1800static int __init pmz_console_setup(struct console *co, char *options);
1801
1802static struct console pmz_console = {
1803	.name	=	PMACZILOG_NAME,
1804	.write	=	pmz_console_write,
1805	.device	=	uart_console_device,
1806	.setup	=	pmz_console_setup,
1807	.flags	=	CON_PRINTBUFFER,
1808	.index	=	-1,
1809	.data   =	&pmz_uart_reg,
1810};
1811
1812#define PMACZILOG_CONSOLE	&pmz_console
1813#else /* CONFIG_SERIAL_PMACZILOG_CONSOLE */
1814#define PMACZILOG_CONSOLE	(NULL)
1815#endif /* CONFIG_SERIAL_PMACZILOG_CONSOLE */
1816
1817/*
1818 * Register the driver, console driver and ports with the serial
1819 * core
1820 */
1821static int __init pmz_register(void)
1822{
1823	pmz_uart_reg.nr = pmz_ports_count;
1824	pmz_uart_reg.cons = PMACZILOG_CONSOLE;
1825
1826	/*
1827	 * Register this driver with the serial core
1828	 */
1829	return uart_register_driver(&pmz_uart_reg);
1830}
1831
1832#ifdef CONFIG_PPC_PMAC
1833
1834static const struct of_device_id pmz_match[] =
1835{
1836	{
1837	.name		= "ch-a",
1838	},
1839	{
1840	.name		= "ch-b",
1841	},
1842	{},
1843};
1844MODULE_DEVICE_TABLE (of, pmz_match);
1845
1846static struct macio_driver pmz_driver = {
1847	.driver = {
1848		.name 		= "pmac_zilog",
1849		.owner		= THIS_MODULE,
1850		.of_match_table	= pmz_match,
1851	},
1852	.probe		= pmz_attach,
1853	.remove		= pmz_detach,
1854	.suspend	= pmz_suspend,
1855	.resume		= pmz_resume,
1856};
1857
1858#else
1859
1860static struct platform_driver pmz_driver = {
1861	.remove		= __exit_p(pmz_detach),
1862	.driver		= {
1863		.name		= "scc",
1864	},
1865};
1866
1867#endif /* !CONFIG_PPC_PMAC */
1868
1869static int __init init_pmz(void)
1870{
1871	int rc, i;
1872	printk(KERN_INFO "%s\n", version);
1873
1874	/* 
1875	 * First, we need to do a direct OF-based probe pass. We
1876	 * do that because we want serial console up before the
1877	 * macio stuffs calls us back, and since that makes it
1878	 * easier to pass the proper number of channels to
1879	 * uart_register_driver()
1880	 */
1881	if (pmz_ports_count == 0)
1882		pmz_probe();
1883
1884	/*
1885	 * Bail early if no port found
1886	 */
1887	if (pmz_ports_count == 0)
1888		return -ENODEV;
1889
1890	/*
1891	 * Now we register with the serial layer
1892	 */
1893	rc = pmz_register();
1894	if (rc) {
1895		printk(KERN_ERR 
1896			"pmac_zilog: Error registering serial device, disabling pmac_zilog.\n"
1897		 	"pmac_zilog: Did another serial driver already claim the minors?\n"); 
1898		/* effectively "pmz_unprobe()" */
1899		for (i=0; i < pmz_ports_count; i++)
1900			pmz_dispose_port(&pmz_ports[i]);
1901		return rc;
1902	}
1903
1904	/*
1905	 * Then we register the macio driver itself
1906	 */
1907#ifdef CONFIG_PPC_PMAC
1908	return macio_register_driver(&pmz_driver);
1909#else
1910	return platform_driver_probe(&pmz_driver, pmz_attach);
1911#endif
1912}
1913
1914static void __exit exit_pmz(void)
1915{
1916	int i;
1917
1918#ifdef CONFIG_PPC_PMAC
1919	/* Get rid of macio-driver (detach from macio) */
1920	macio_unregister_driver(&pmz_driver);
1921#else
1922	platform_driver_unregister(&pmz_driver);
1923#endif
1924
1925	for (i = 0; i < pmz_ports_count; i++) {
1926		struct uart_pmac_port *uport = &pmz_ports[i];
1927#ifdef CONFIG_PPC_PMAC
1928		if (uport->node != NULL)
1929			pmz_dispose_port(uport);
1930#else
1931		if (uport->pdev != NULL)
1932			pmz_dispose_port(uport);
1933#endif
1934	}
1935	/* Unregister UART driver */
1936	uart_unregister_driver(&pmz_uart_reg);
1937}
1938
1939#ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE
1940
1941static void pmz_console_putchar(struct uart_port *port, int ch)
1942{
1943	struct uart_pmac_port *uap =
1944		container_of(port, struct uart_pmac_port, port);
1945
1946	/* Wait for the transmit buffer to empty. */
1947	while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0)
1948		udelay(5);
1949	write_zsdata(uap, ch);
1950}
1951
1952/*
1953 * Print a string to the serial port trying not to disturb
1954 * any possible real use of the port...
1955 */
1956static void pmz_console_write(struct console *con, const char *s, unsigned int count)
1957{
1958	struct uart_pmac_port *uap = &pmz_ports[con->index];
1959	unsigned long flags;
1960
1961	spin_lock_irqsave(&uap->port.lock, flags);
1962
1963	/* Turn of interrupts and enable the transmitter. */
1964	write_zsreg(uap, R1, uap->curregs[1] & ~TxINT_ENAB);
1965	write_zsreg(uap, R5, uap->curregs[5] | TxENABLE | RTS | DTR);
1966
1967	uart_console_write(&uap->port, s, count, pmz_console_putchar);
1968
1969	/* Restore the values in the registers. */
1970	write_zsreg(uap, R1, uap->curregs[1]);
1971	/* Don't disable the transmitter. */
1972
1973	spin_unlock_irqrestore(&uap->port.lock, flags);
1974}
1975
1976/*
1977 * Setup the serial console
1978 */
1979static int __init pmz_console_setup(struct console *co, char *options)
1980{
1981	struct uart_pmac_port *uap;
1982	struct uart_port *port;
1983	int baud = 38400;
1984	int bits = 8;
1985	int parity = 'n';
1986	int flow = 'n';
1987	unsigned long pwr_delay;
1988
1989	/*
1990	 * XServe's default to 57600 bps
1991	 */
1992	if (of_machine_is_compatible("RackMac1,1")
1993	    || of_machine_is_compatible("RackMac1,2")
1994	    || of_machine_is_compatible("MacRISC4"))
1995		baud = 57600;
1996
1997	/*
1998	 * Check whether an invalid uart number has been specified, and
1999	 * if so, search for the first available port that does have
2000	 * console support.
2001	 */
2002	if (co->index >= pmz_ports_count)
2003		co->index = 0;
2004	uap = &pmz_ports[co->index];
2005#ifdef CONFIG_PPC_PMAC
2006	if (uap->node == NULL)
2007		return -ENODEV;
2008#else
2009	if (uap->pdev == NULL)
2010		return -ENODEV;
2011#endif
2012	port = &uap->port;
2013
2014	/*
2015	 * Mark port as beeing a console
2016	 */
2017	uap->flags |= PMACZILOG_FLAG_IS_CONS;
2018
2019	/*
2020	 * Temporary fix for uart layer who didn't setup the spinlock yet
2021	 */
2022	spin_lock_init(&port->lock);
2023
2024	/*
2025	 * Enable the hardware
2026	 */
2027	pwr_delay = __pmz_startup(uap);
2028	if (pwr_delay)
2029		mdelay(pwr_delay);
2030	
2031	if (options)
2032		uart_parse_options(options, &baud, &parity, &bits, &flow);
2033
2034	return uart_set_options(port, co, baud, parity, bits, flow);
2035}
2036
2037static int __init pmz_console_init(void)
2038{
2039	/* Probe ports */
2040	pmz_probe();
2041
2042	if (pmz_ports_count == 0)
2043		return -ENODEV;
2044
2045	/* TODO: Autoprobe console based on OF */
2046	/* pmz_console.index = i; */
2047	register_console(&pmz_console);
2048
2049	return 0;
2050
2051}
2052console_initcall(pmz_console_init);
2053#endif /* CONFIG_SERIAL_PMACZILOG_CONSOLE */
2054
2055module_init(init_pmz);
2056module_exit(exit_pmz);