Loading...
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Driver for Zilog serial chips found on SGI workstations and
4 * servers. This driver could actually be made more generic.
5 *
6 * This is based on the drivers/serial/sunzilog.c code as of 2.6.0-test7 and the
7 * old drivers/sgi/char/sgiserial.c code which itself is based of the original
8 * drivers/sbus/char/zs.c code. A lot of code has been simply moved over
9 * directly from there but much has been rewritten. Credits therefore go out
10 * to David S. Miller, Eddie C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell
11 * for their work there.
12 *
13 * Copyright (C) 2002 Ralf Baechle (ralf@linux-mips.org)
14 * Copyright (C) 2002 David S. Miller (davem@redhat.com)
15 */
16#include <linux/module.h>
17#include <linux/kernel.h>
18#include <linux/errno.h>
19#include <linux/delay.h>
20#include <linux/tty.h>
21#include <linux/tty_flip.h>
22#include <linux/major.h>
23#include <linux/string.h>
24#include <linux/ptrace.h>
25#include <linux/ioport.h>
26#include <linux/slab.h>
27#include <linux/circ_buf.h>
28#include <linux/serial.h>
29#include <linux/sysrq.h>
30#include <linux/console.h>
31#include <linux/spinlock.h>
32#include <linux/init.h>
33
34#include <asm/io.h>
35#include <asm/irq.h>
36#include <asm/sgialib.h>
37#include <asm/sgi/ioc.h>
38#include <asm/sgi/hpc3.h>
39#include <asm/sgi/ip22.h>
40
41#if defined(CONFIG_SERIAL_IP22_ZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
42#define SUPPORT_SYSRQ
43#endif
44
45#include <linux/serial_core.h>
46
47#include "ip22zilog.h"
48
49/*
50 * On IP22 we need to delay after register accesses but we do not need to
51 * flush writes.
52 */
53#define ZSDELAY() udelay(5)
54#define ZSDELAY_LONG() udelay(20)
55#define ZS_WSYNC(channel) do { } while (0)
56
57#define NUM_IP22ZILOG 1
58#define NUM_CHANNELS (NUM_IP22ZILOG * 2)
59
60#define ZS_CLOCK 3672000 /* Zilog input clock rate. */
61#define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */
62
63/*
64 * We wrap our port structure around the generic uart_port.
65 */
66struct uart_ip22zilog_port {
67 struct uart_port port;
68
69 /* IRQ servicing chain. */
70 struct uart_ip22zilog_port *next;
71
72 /* Current values of Zilog write registers. */
73 unsigned char curregs[NUM_ZSREGS];
74
75 unsigned int flags;
76#define IP22ZILOG_FLAG_IS_CONS 0x00000004
77#define IP22ZILOG_FLAG_IS_KGDB 0x00000008
78#define IP22ZILOG_FLAG_MODEM_STATUS 0x00000010
79#define IP22ZILOG_FLAG_IS_CHANNEL_A 0x00000020
80#define IP22ZILOG_FLAG_REGS_HELD 0x00000040
81#define IP22ZILOG_FLAG_TX_STOPPED 0x00000080
82#define IP22ZILOG_FLAG_TX_ACTIVE 0x00000100
83#define IP22ZILOG_FLAG_RESET_DONE 0x00000200
84
85 unsigned int tty_break;
86
87 unsigned char parity_mask;
88 unsigned char prev_status;
89};
90
91#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel *)((PORT)->membase))
92#define UART_ZILOG(PORT) ((struct uart_ip22zilog_port *)(PORT))
93#define IP22ZILOG_GET_CURR_REG(PORT, REGNUM) \
94 (UART_ZILOG(PORT)->curregs[REGNUM])
95#define IP22ZILOG_SET_CURR_REG(PORT, REGNUM, REGVAL) \
96 ((UART_ZILOG(PORT)->curregs[REGNUM]) = (REGVAL))
97#define ZS_IS_CONS(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CONS)
98#define ZS_IS_KGDB(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_KGDB)
99#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & IP22ZILOG_FLAG_MODEM_STATUS)
100#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CHANNEL_A)
101#define ZS_REGS_HELD(UP) ((UP)->flags & IP22ZILOG_FLAG_REGS_HELD)
102#define ZS_TX_STOPPED(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_STOPPED)
103#define ZS_TX_ACTIVE(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_ACTIVE)
104
105/* Reading and writing Zilog8530 registers. The delays are to make this
106 * driver work on the IP22 which needs a settling delay after each chip
107 * register access, other machines handle this in hardware via auxiliary
108 * flip-flops which implement the settle time we do in software.
109 *
110 * The port lock must be held and local IRQs must be disabled
111 * when {read,write}_zsreg is invoked.
112 */
113static unsigned char read_zsreg(struct zilog_channel *channel,
114 unsigned char reg)
115{
116 unsigned char retval;
117
118 writeb(reg, &channel->control);
119 ZSDELAY();
120 retval = readb(&channel->control);
121 ZSDELAY();
122
123 return retval;
124}
125
126static void write_zsreg(struct zilog_channel *channel,
127 unsigned char reg, unsigned char value)
128{
129 writeb(reg, &channel->control);
130 ZSDELAY();
131 writeb(value, &channel->control);
132 ZSDELAY();
133}
134
135static void ip22zilog_clear_fifo(struct zilog_channel *channel)
136{
137 int i;
138
139 for (i = 0; i < 32; i++) {
140 unsigned char regval;
141
142 regval = readb(&channel->control);
143 ZSDELAY();
144 if (regval & Rx_CH_AV)
145 break;
146
147 regval = read_zsreg(channel, R1);
148 readb(&channel->data);
149 ZSDELAY();
150
151 if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) {
152 writeb(ERR_RES, &channel->control);
153 ZSDELAY();
154 ZS_WSYNC(channel);
155 }
156 }
157}
158
159/* This function must only be called when the TX is not busy. The UART
160 * port lock must be held and local interrupts disabled.
161 */
162static void __load_zsregs(struct zilog_channel *channel, unsigned char *regs)
163{
164 int i;
165
166 /* Let pending transmits finish. */
167 for (i = 0; i < 1000; i++) {
168 unsigned char stat = read_zsreg(channel, R1);
169 if (stat & ALL_SNT)
170 break;
171 udelay(100);
172 }
173
174 writeb(ERR_RES, &channel->control);
175 ZSDELAY();
176 ZS_WSYNC(channel);
177
178 ip22zilog_clear_fifo(channel);
179
180 /* Disable all interrupts. */
181 write_zsreg(channel, R1,
182 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
183
184 /* Set parity, sync config, stop bits, and clock divisor. */
185 write_zsreg(channel, R4, regs[R4]);
186
187 /* Set misc. TX/RX control bits. */
188 write_zsreg(channel, R10, regs[R10]);
189
190 /* Set TX/RX controls sans the enable bits. */
191 write_zsreg(channel, R3, regs[R3] & ~RxENAB);
192 write_zsreg(channel, R5, regs[R5] & ~TxENAB);
193
194 /* Synchronous mode config. */
195 write_zsreg(channel, R6, regs[R6]);
196 write_zsreg(channel, R7, regs[R7]);
197
198 /* Don't mess with the interrupt vector (R2, unused by us) and
199 * master interrupt control (R9). We make sure this is setup
200 * properly at probe time then never touch it again.
201 */
202
203 /* Disable baud generator. */
204 write_zsreg(channel, R14, regs[R14] & ~BRENAB);
205
206 /* Clock mode control. */
207 write_zsreg(channel, R11, regs[R11]);
208
209 /* Lower and upper byte of baud rate generator divisor. */
210 write_zsreg(channel, R12, regs[R12]);
211 write_zsreg(channel, R13, regs[R13]);
212
213 /* Now rewrite R14, with BRENAB (if set). */
214 write_zsreg(channel, R14, regs[R14]);
215
216 /* External status interrupt control. */
217 write_zsreg(channel, R15, regs[R15]);
218
219 /* Reset external status interrupts. */
220 write_zsreg(channel, R0, RES_EXT_INT);
221 write_zsreg(channel, R0, RES_EXT_INT);
222
223 /* Rewrite R3/R5, this time without enables masked. */
224 write_zsreg(channel, R3, regs[R3]);
225 write_zsreg(channel, R5, regs[R5]);
226
227 /* Rewrite R1, this time without IRQ enabled masked. */
228 write_zsreg(channel, R1, regs[R1]);
229}
230
231/* Reprogram the Zilog channel HW registers with the copies found in the
232 * software state struct. If the transmitter is busy, we defer this update
233 * until the next TX complete interrupt. Else, we do it right now.
234 *
235 * The UART port lock must be held and local interrupts disabled.
236 */
237static void ip22zilog_maybe_update_regs(struct uart_ip22zilog_port *up,
238 struct zilog_channel *channel)
239{
240 if (!ZS_REGS_HELD(up)) {
241 if (ZS_TX_ACTIVE(up)) {
242 up->flags |= IP22ZILOG_FLAG_REGS_HELD;
243 } else {
244 __load_zsregs(channel, up->curregs);
245 }
246 }
247}
248
249#define Rx_BRK 0x0100 /* BREAK event software flag. */
250#define Rx_SYS 0x0200 /* SysRq event software flag. */
251
252static bool ip22zilog_receive_chars(struct uart_ip22zilog_port *up,
253 struct zilog_channel *channel)
254{
255 unsigned char ch, flag;
256 unsigned int r1;
257 bool push = up->port.state != NULL;
258
259 for (;;) {
260 ch = readb(&channel->control);
261 ZSDELAY();
262 if (!(ch & Rx_CH_AV))
263 break;
264
265 r1 = read_zsreg(channel, R1);
266 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
267 writeb(ERR_RES, &channel->control);
268 ZSDELAY();
269 ZS_WSYNC(channel);
270 }
271
272 ch = readb(&channel->data);
273 ZSDELAY();
274
275 ch &= up->parity_mask;
276
277 /* Handle the null char got when BREAK is removed. */
278 if (!ch)
279 r1 |= up->tty_break;
280
281 /* A real serial line, record the character and status. */
282 flag = TTY_NORMAL;
283 up->port.icount.rx++;
284 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR | Rx_SYS | Rx_BRK)) {
285 up->tty_break = 0;
286
287 if (r1 & (Rx_SYS | Rx_BRK)) {
288 up->port.icount.brk++;
289 if (r1 & Rx_SYS)
290 continue;
291 r1 &= ~(PAR_ERR | CRC_ERR);
292 }
293 else if (r1 & PAR_ERR)
294 up->port.icount.parity++;
295 else if (r1 & CRC_ERR)
296 up->port.icount.frame++;
297 if (r1 & Rx_OVR)
298 up->port.icount.overrun++;
299 r1 &= up->port.read_status_mask;
300 if (r1 & Rx_BRK)
301 flag = TTY_BREAK;
302 else if (r1 & PAR_ERR)
303 flag = TTY_PARITY;
304 else if (r1 & CRC_ERR)
305 flag = TTY_FRAME;
306 }
307
308 if (uart_handle_sysrq_char(&up->port, ch))
309 continue;
310
311 if (push)
312 uart_insert_char(&up->port, r1, Rx_OVR, ch, flag);
313 }
314 return push;
315}
316
317static void ip22zilog_status_handle(struct uart_ip22zilog_port *up,
318 struct zilog_channel *channel)
319{
320 unsigned char status;
321
322 status = readb(&channel->control);
323 ZSDELAY();
324
325 writeb(RES_EXT_INT, &channel->control);
326 ZSDELAY();
327 ZS_WSYNC(channel);
328
329 if (up->curregs[R15] & BRKIE) {
330 if ((status & BRK_ABRT) && !(up->prev_status & BRK_ABRT)) {
331 if (uart_handle_break(&up->port))
332 up->tty_break = Rx_SYS;
333 else
334 up->tty_break = Rx_BRK;
335 }
336 }
337
338 if (ZS_WANTS_MODEM_STATUS(up)) {
339 if (status & SYNC)
340 up->port.icount.dsr++;
341
342 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
343 * But it does not tell us which bit has changed, we have to keep
344 * track of this ourselves.
345 */
346 if ((status ^ up->prev_status) ^ DCD)
347 uart_handle_dcd_change(&up->port,
348 (status & DCD));
349 if ((status ^ up->prev_status) ^ CTS)
350 uart_handle_cts_change(&up->port,
351 (status & CTS));
352
353 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
354 }
355
356 up->prev_status = status;
357}
358
359static void ip22zilog_transmit_chars(struct uart_ip22zilog_port *up,
360 struct zilog_channel *channel)
361{
362 struct circ_buf *xmit;
363
364 if (ZS_IS_CONS(up)) {
365 unsigned char status = readb(&channel->control);
366 ZSDELAY();
367
368 /* TX still busy? Just wait for the next TX done interrupt.
369 *
370 * It can occur because of how we do serial console writes. It would
371 * be nice to transmit console writes just like we normally would for
372 * a TTY line. (ie. buffered and TX interrupt driven). That is not
373 * easy because console writes cannot sleep. One solution might be
374 * to poll on enough port->xmit space becoming free. -DaveM
375 */
376 if (!(status & Tx_BUF_EMP))
377 return;
378 }
379
380 up->flags &= ~IP22ZILOG_FLAG_TX_ACTIVE;
381
382 if (ZS_REGS_HELD(up)) {
383 __load_zsregs(channel, up->curregs);
384 up->flags &= ~IP22ZILOG_FLAG_REGS_HELD;
385 }
386
387 if (ZS_TX_STOPPED(up)) {
388 up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED;
389 goto ack_tx_int;
390 }
391
392 if (up->port.x_char) {
393 up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
394 writeb(up->port.x_char, &channel->data);
395 ZSDELAY();
396 ZS_WSYNC(channel);
397
398 up->port.icount.tx++;
399 up->port.x_char = 0;
400 return;
401 }
402
403 if (up->port.state == NULL)
404 goto ack_tx_int;
405 xmit = &up->port.state->xmit;
406 if (uart_circ_empty(xmit))
407 goto ack_tx_int;
408 if (uart_tx_stopped(&up->port))
409 goto ack_tx_int;
410
411 up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
412 writeb(xmit->buf[xmit->tail], &channel->data);
413 ZSDELAY();
414 ZS_WSYNC(channel);
415
416 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
417 up->port.icount.tx++;
418
419 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
420 uart_write_wakeup(&up->port);
421
422 return;
423
424ack_tx_int:
425 writeb(RES_Tx_P, &channel->control);
426 ZSDELAY();
427 ZS_WSYNC(channel);
428}
429
430static irqreturn_t ip22zilog_interrupt(int irq, void *dev_id)
431{
432 struct uart_ip22zilog_port *up = dev_id;
433
434 while (up) {
435 struct zilog_channel *channel
436 = ZILOG_CHANNEL_FROM_PORT(&up->port);
437 unsigned char r3;
438 bool push = false;
439
440 spin_lock(&up->port.lock);
441 r3 = read_zsreg(channel, R3);
442
443 /* Channel A */
444 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
445 writeb(RES_H_IUS, &channel->control);
446 ZSDELAY();
447 ZS_WSYNC(channel);
448
449 if (r3 & CHARxIP)
450 push = ip22zilog_receive_chars(up, channel);
451 if (r3 & CHAEXT)
452 ip22zilog_status_handle(up, channel);
453 if (r3 & CHATxIP)
454 ip22zilog_transmit_chars(up, channel);
455 }
456 spin_unlock(&up->port.lock);
457
458 if (push)
459 tty_flip_buffer_push(&up->port.state->port);
460
461 /* Channel B */
462 up = up->next;
463 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
464 push = false;
465
466 spin_lock(&up->port.lock);
467 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
468 writeb(RES_H_IUS, &channel->control);
469 ZSDELAY();
470 ZS_WSYNC(channel);
471
472 if (r3 & CHBRxIP)
473 push = ip22zilog_receive_chars(up, channel);
474 if (r3 & CHBEXT)
475 ip22zilog_status_handle(up, channel);
476 if (r3 & CHBTxIP)
477 ip22zilog_transmit_chars(up, channel);
478 }
479 spin_unlock(&up->port.lock);
480
481 if (push)
482 tty_flip_buffer_push(&up->port.state->port);
483
484 up = up->next;
485 }
486
487 return IRQ_HANDLED;
488}
489
490/* A convenient way to quickly get R0 status. The caller must _not_ hold the
491 * port lock, it is acquired here.
492 */
493static __inline__ unsigned char ip22zilog_read_channel_status(struct uart_port *port)
494{
495 struct zilog_channel *channel;
496 unsigned char status;
497
498 channel = ZILOG_CHANNEL_FROM_PORT(port);
499 status = readb(&channel->control);
500 ZSDELAY();
501
502 return status;
503}
504
505/* The port lock is not held. */
506static unsigned int ip22zilog_tx_empty(struct uart_port *port)
507{
508 unsigned long flags;
509 unsigned char status;
510 unsigned int ret;
511
512 spin_lock_irqsave(&port->lock, flags);
513
514 status = ip22zilog_read_channel_status(port);
515
516 spin_unlock_irqrestore(&port->lock, flags);
517
518 if (status & Tx_BUF_EMP)
519 ret = TIOCSER_TEMT;
520 else
521 ret = 0;
522
523 return ret;
524}
525
526/* The port lock is held and interrupts are disabled. */
527static unsigned int ip22zilog_get_mctrl(struct uart_port *port)
528{
529 unsigned char status;
530 unsigned int ret;
531
532 status = ip22zilog_read_channel_status(port);
533
534 ret = 0;
535 if (status & DCD)
536 ret |= TIOCM_CAR;
537 if (status & SYNC)
538 ret |= TIOCM_DSR;
539 if (status & CTS)
540 ret |= TIOCM_CTS;
541
542 return ret;
543}
544
545/* The port lock is held and interrupts are disabled. */
546static void ip22zilog_set_mctrl(struct uart_port *port, unsigned int mctrl)
547{
548 struct uart_ip22zilog_port *up =
549 container_of(port, struct uart_ip22zilog_port, port);
550 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
551 unsigned char set_bits, clear_bits;
552
553 set_bits = clear_bits = 0;
554
555 if (mctrl & TIOCM_RTS)
556 set_bits |= RTS;
557 else
558 clear_bits |= RTS;
559 if (mctrl & TIOCM_DTR)
560 set_bits |= DTR;
561 else
562 clear_bits |= DTR;
563
564 /* NOTE: Not subject to 'transmitter active' rule. */
565 up->curregs[R5] |= set_bits;
566 up->curregs[R5] &= ~clear_bits;
567 write_zsreg(channel, R5, up->curregs[R5]);
568}
569
570/* The port lock is held and interrupts are disabled. */
571static void ip22zilog_stop_tx(struct uart_port *port)
572{
573 struct uart_ip22zilog_port *up =
574 container_of(port, struct uart_ip22zilog_port, port);
575
576 up->flags |= IP22ZILOG_FLAG_TX_STOPPED;
577}
578
579/* The port lock is held and interrupts are disabled. */
580static void ip22zilog_start_tx(struct uart_port *port)
581{
582 struct uart_ip22zilog_port *up =
583 container_of(port, struct uart_ip22zilog_port, port);
584 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
585 unsigned char status;
586
587 up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
588 up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED;
589
590 status = readb(&channel->control);
591 ZSDELAY();
592
593 /* TX busy? Just wait for the TX done interrupt. */
594 if (!(status & Tx_BUF_EMP))
595 return;
596
597 /* Send the first character to jump-start the TX done
598 * IRQ sending engine.
599 */
600 if (port->x_char) {
601 writeb(port->x_char, &channel->data);
602 ZSDELAY();
603 ZS_WSYNC(channel);
604
605 port->icount.tx++;
606 port->x_char = 0;
607 } else {
608 struct circ_buf *xmit = &port->state->xmit;
609
610 if (uart_circ_empty(xmit))
611 return;
612 writeb(xmit->buf[xmit->tail], &channel->data);
613 ZSDELAY();
614 ZS_WSYNC(channel);
615
616 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
617 port->icount.tx++;
618
619 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
620 uart_write_wakeup(&up->port);
621 }
622}
623
624/* The port lock is held and interrupts are disabled. */
625static void ip22zilog_stop_rx(struct uart_port *port)
626{
627 struct uart_ip22zilog_port *up = UART_ZILOG(port);
628 struct zilog_channel *channel;
629
630 if (ZS_IS_CONS(up))
631 return;
632
633 channel = ZILOG_CHANNEL_FROM_PORT(port);
634
635 /* Disable all RX interrupts. */
636 up->curregs[R1] &= ~RxINT_MASK;
637 ip22zilog_maybe_update_regs(up, channel);
638}
639
640/* The port lock is held. */
641static void ip22zilog_enable_ms(struct uart_port *port)
642{
643 struct uart_ip22zilog_port *up =
644 container_of(port, struct uart_ip22zilog_port, port);
645 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
646 unsigned char new_reg;
647
648 new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
649 if (new_reg != up->curregs[R15]) {
650 up->curregs[R15] = new_reg;
651
652 /* NOTE: Not subject to 'transmitter active' rule. */
653 write_zsreg(channel, R15, up->curregs[R15]);
654 }
655}
656
657/* The port lock is not held. */
658static void ip22zilog_break_ctl(struct uart_port *port, int break_state)
659{
660 struct uart_ip22zilog_port *up =
661 container_of(port, struct uart_ip22zilog_port, port);
662 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
663 unsigned char set_bits, clear_bits, new_reg;
664 unsigned long flags;
665
666 set_bits = clear_bits = 0;
667
668 if (break_state)
669 set_bits |= SND_BRK;
670 else
671 clear_bits |= SND_BRK;
672
673 spin_lock_irqsave(&port->lock, flags);
674
675 new_reg = (up->curregs[R5] | set_bits) & ~clear_bits;
676 if (new_reg != up->curregs[R5]) {
677 up->curregs[R5] = new_reg;
678
679 /* NOTE: Not subject to 'transmitter active' rule. */
680 write_zsreg(channel, R5, up->curregs[R5]);
681 }
682
683 spin_unlock_irqrestore(&port->lock, flags);
684}
685
686static void __ip22zilog_reset(struct uart_ip22zilog_port *up)
687{
688 struct zilog_channel *channel;
689 int i;
690
691 if (up->flags & IP22ZILOG_FLAG_RESET_DONE)
692 return;
693
694 /* Let pending transmits finish. */
695 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
696 for (i = 0; i < 1000; i++) {
697 unsigned char stat = read_zsreg(channel, R1);
698 if (stat & ALL_SNT)
699 break;
700 udelay(100);
701 }
702
703 if (!ZS_IS_CHANNEL_A(up)) {
704 up++;
705 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
706 }
707 write_zsreg(channel, R9, FHWRES);
708 ZSDELAY_LONG();
709 (void) read_zsreg(channel, R0);
710
711 up->flags |= IP22ZILOG_FLAG_RESET_DONE;
712 up->next->flags |= IP22ZILOG_FLAG_RESET_DONE;
713}
714
715static void __ip22zilog_startup(struct uart_ip22zilog_port *up)
716{
717 struct zilog_channel *channel;
718
719 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
720
721 __ip22zilog_reset(up);
722
723 __load_zsregs(channel, up->curregs);
724 /* set master interrupt enable */
725 write_zsreg(channel, R9, up->curregs[R9]);
726 up->prev_status = readb(&channel->control);
727
728 /* Enable receiver and transmitter. */
729 up->curregs[R3] |= RxENAB;
730 up->curregs[R5] |= TxENAB;
731
732 up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
733 ip22zilog_maybe_update_regs(up, channel);
734}
735
736static int ip22zilog_startup(struct uart_port *port)
737{
738 struct uart_ip22zilog_port *up = UART_ZILOG(port);
739 unsigned long flags;
740
741 if (ZS_IS_CONS(up))
742 return 0;
743
744 spin_lock_irqsave(&port->lock, flags);
745 __ip22zilog_startup(up);
746 spin_unlock_irqrestore(&port->lock, flags);
747 return 0;
748}
749
750/*
751 * The test for ZS_IS_CONS is explained by the following e-mail:
752 *****
753 * From: Russell King <rmk@arm.linux.org.uk>
754 * Date: Sun, 8 Dec 2002 10:18:38 +0000
755 *
756 * On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote:
757 * > I boot my 2.5 boxes using "console=ttyS0,9600" argument,
758 * > and I noticed that something is not right with reference
759 * > counting in this case. It seems that when the console
760 * > is open by kernel initially, this is not accounted
761 * > as an open, and uart_startup is not called.
762 *
763 * That is correct. We are unable to call uart_startup when the serial
764 * console is initialised because it may need to allocate memory (as
765 * request_irq does) and the memory allocators may not have been
766 * initialised.
767 *
768 * 1. initialise the port into a state where it can send characters in the
769 * console write method.
770 *
771 * 2. don't do the actual hardware shutdown in your shutdown() method (but
772 * do the normal software shutdown - ie, free irqs etc)
773 *****
774 */
775static void ip22zilog_shutdown(struct uart_port *port)
776{
777 struct uart_ip22zilog_port *up = UART_ZILOG(port);
778 struct zilog_channel *channel;
779 unsigned long flags;
780
781 if (ZS_IS_CONS(up))
782 return;
783
784 spin_lock_irqsave(&port->lock, flags);
785
786 channel = ZILOG_CHANNEL_FROM_PORT(port);
787
788 /* Disable receiver and transmitter. */
789 up->curregs[R3] &= ~RxENAB;
790 up->curregs[R5] &= ~TxENAB;
791
792 /* Disable all interrupts and BRK assertion. */
793 up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
794 up->curregs[R5] &= ~SND_BRK;
795 ip22zilog_maybe_update_regs(up, channel);
796
797 spin_unlock_irqrestore(&port->lock, flags);
798}
799
800/* Shared by TTY driver and serial console setup. The port lock is held
801 * and local interrupts are disabled.
802 */
803static void
804ip22zilog_convert_to_zs(struct uart_ip22zilog_port *up, unsigned int cflag,
805 unsigned int iflag, int brg)
806{
807
808 up->curregs[R10] = NRZ;
809 up->curregs[R11] = TCBR | RCBR;
810
811 /* Program BAUD and clock source. */
812 up->curregs[R4] &= ~XCLK_MASK;
813 up->curregs[R4] |= X16CLK;
814 up->curregs[R12] = brg & 0xff;
815 up->curregs[R13] = (brg >> 8) & 0xff;
816 up->curregs[R14] = BRENAB;
817
818 /* Character size, stop bits, and parity. */
819 up->curregs[3] &= ~RxN_MASK;
820 up->curregs[5] &= ~TxN_MASK;
821 switch (cflag & CSIZE) {
822 case CS5:
823 up->curregs[3] |= Rx5;
824 up->curregs[5] |= Tx5;
825 up->parity_mask = 0x1f;
826 break;
827 case CS6:
828 up->curregs[3] |= Rx6;
829 up->curregs[5] |= Tx6;
830 up->parity_mask = 0x3f;
831 break;
832 case CS7:
833 up->curregs[3] |= Rx7;
834 up->curregs[5] |= Tx7;
835 up->parity_mask = 0x7f;
836 break;
837 case CS8:
838 default:
839 up->curregs[3] |= Rx8;
840 up->curregs[5] |= Tx8;
841 up->parity_mask = 0xff;
842 break;
843 }
844 up->curregs[4] &= ~0x0c;
845 if (cflag & CSTOPB)
846 up->curregs[4] |= SB2;
847 else
848 up->curregs[4] |= SB1;
849 if (cflag & PARENB)
850 up->curregs[4] |= PAR_ENAB;
851 else
852 up->curregs[4] &= ~PAR_ENAB;
853 if (!(cflag & PARODD))
854 up->curregs[4] |= PAR_EVEN;
855 else
856 up->curregs[4] &= ~PAR_EVEN;
857
858 up->port.read_status_mask = Rx_OVR;
859 if (iflag & INPCK)
860 up->port.read_status_mask |= CRC_ERR | PAR_ERR;
861 if (iflag & (IGNBRK | BRKINT | PARMRK))
862 up->port.read_status_mask |= BRK_ABRT;
863
864 up->port.ignore_status_mask = 0;
865 if (iflag & IGNPAR)
866 up->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
867 if (iflag & IGNBRK) {
868 up->port.ignore_status_mask |= BRK_ABRT;
869 if (iflag & IGNPAR)
870 up->port.ignore_status_mask |= Rx_OVR;
871 }
872
873 if ((cflag & CREAD) == 0)
874 up->port.ignore_status_mask = 0xff;
875}
876
877/* The port lock is not held. */
878static void
879ip22zilog_set_termios(struct uart_port *port, struct ktermios *termios,
880 struct ktermios *old)
881{
882 struct uart_ip22zilog_port *up =
883 container_of(port, struct uart_ip22zilog_port, port);
884 unsigned long flags;
885 int baud, brg;
886
887 baud = uart_get_baud_rate(port, termios, old, 1200, 76800);
888
889 spin_lock_irqsave(&up->port.lock, flags);
890
891 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
892
893 ip22zilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg);
894
895 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
896 up->flags |= IP22ZILOG_FLAG_MODEM_STATUS;
897 else
898 up->flags &= ~IP22ZILOG_FLAG_MODEM_STATUS;
899
900 ip22zilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port));
901 uart_update_timeout(port, termios->c_cflag, baud);
902
903 spin_unlock_irqrestore(&up->port.lock, flags);
904}
905
906static const char *ip22zilog_type(struct uart_port *port)
907{
908 return "IP22-Zilog";
909}
910
911/* We do not request/release mappings of the registers here, this
912 * happens at early serial probe time.
913 */
914static void ip22zilog_release_port(struct uart_port *port)
915{
916}
917
918static int ip22zilog_request_port(struct uart_port *port)
919{
920 return 0;
921}
922
923/* These do not need to do anything interesting either. */
924static void ip22zilog_config_port(struct uart_port *port, int flags)
925{
926}
927
928/* We do not support letting the user mess with the divisor, IRQ, etc. */
929static int ip22zilog_verify_port(struct uart_port *port, struct serial_struct *ser)
930{
931 return -EINVAL;
932}
933
934static const struct uart_ops ip22zilog_pops = {
935 .tx_empty = ip22zilog_tx_empty,
936 .set_mctrl = ip22zilog_set_mctrl,
937 .get_mctrl = ip22zilog_get_mctrl,
938 .stop_tx = ip22zilog_stop_tx,
939 .start_tx = ip22zilog_start_tx,
940 .stop_rx = ip22zilog_stop_rx,
941 .enable_ms = ip22zilog_enable_ms,
942 .break_ctl = ip22zilog_break_ctl,
943 .startup = ip22zilog_startup,
944 .shutdown = ip22zilog_shutdown,
945 .set_termios = ip22zilog_set_termios,
946 .type = ip22zilog_type,
947 .release_port = ip22zilog_release_port,
948 .request_port = ip22zilog_request_port,
949 .config_port = ip22zilog_config_port,
950 .verify_port = ip22zilog_verify_port,
951};
952
953static struct uart_ip22zilog_port *ip22zilog_port_table;
954static struct zilog_layout **ip22zilog_chip_regs;
955
956static struct uart_ip22zilog_port *ip22zilog_irq_chain;
957static int zilog_irq = -1;
958
959static void * __init alloc_one_table(unsigned long size)
960{
961 return kzalloc(size, GFP_KERNEL);
962}
963
964static void __init ip22zilog_alloc_tables(void)
965{
966 ip22zilog_port_table = (struct uart_ip22zilog_port *)
967 alloc_one_table(NUM_CHANNELS * sizeof(struct uart_ip22zilog_port));
968 ip22zilog_chip_regs = (struct zilog_layout **)
969 alloc_one_table(NUM_IP22ZILOG * sizeof(struct zilog_layout *));
970
971 if (ip22zilog_port_table == NULL || ip22zilog_chip_regs == NULL) {
972 panic("IP22-Zilog: Cannot allocate IP22-Zilog tables.");
973 }
974}
975
976/* Get the address of the registers for IP22-Zilog instance CHIP. */
977static struct zilog_layout * __init get_zs(int chip)
978{
979 unsigned long base;
980
981 if (chip < 0 || chip >= NUM_IP22ZILOG) {
982 panic("IP22-Zilog: Illegal chip number %d in get_zs.", chip);
983 }
984
985 /* Not probe-able, hard code it. */
986 base = (unsigned long) &sgioc->uart;
987
988 zilog_irq = SGI_SERIAL_IRQ;
989 request_mem_region(base, 8, "IP22-Zilog");
990
991 return (struct zilog_layout *) base;
992}
993
994#define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */
995
996#ifdef CONFIG_SERIAL_IP22_ZILOG_CONSOLE
997static void ip22zilog_put_char(struct uart_port *port, int ch)
998{
999 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
1000 int loops = ZS_PUT_CHAR_MAX_DELAY;
1001
1002 /* This is a timed polling loop so do not switch the explicit
1003 * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM
1004 */
1005 do {
1006 unsigned char val = readb(&channel->control);
1007 if (val & Tx_BUF_EMP) {
1008 ZSDELAY();
1009 break;
1010 }
1011 udelay(5);
1012 } while (--loops);
1013
1014 writeb(ch, &channel->data);
1015 ZSDELAY();
1016 ZS_WSYNC(channel);
1017}
1018
1019static void
1020ip22zilog_console_write(struct console *con, const char *s, unsigned int count)
1021{
1022 struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index];
1023 unsigned long flags;
1024
1025 spin_lock_irqsave(&up->port.lock, flags);
1026 uart_console_write(&up->port, s, count, ip22zilog_put_char);
1027 udelay(2);
1028 spin_unlock_irqrestore(&up->port.lock, flags);
1029}
1030
1031static int __init ip22zilog_console_setup(struct console *con, char *options)
1032{
1033 struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index];
1034 unsigned long flags;
1035 int baud = 9600, bits = 8;
1036 int parity = 'n';
1037 int flow = 'n';
1038
1039 up->flags |= IP22ZILOG_FLAG_IS_CONS;
1040
1041 printk(KERN_INFO "Console: ttyS%d (IP22-Zilog)\n", con->index);
1042
1043 spin_lock_irqsave(&up->port.lock, flags);
1044
1045 up->curregs[R15] |= BRKIE;
1046
1047 __ip22zilog_startup(up);
1048
1049 spin_unlock_irqrestore(&up->port.lock, flags);
1050
1051 if (options)
1052 uart_parse_options(options, &baud, &parity, &bits, &flow);
1053 return uart_set_options(&up->port, con, baud, parity, bits, flow);
1054}
1055
1056static struct uart_driver ip22zilog_reg;
1057
1058static struct console ip22zilog_console = {
1059 .name = "ttyS",
1060 .write = ip22zilog_console_write,
1061 .device = uart_console_device,
1062 .setup = ip22zilog_console_setup,
1063 .flags = CON_PRINTBUFFER,
1064 .index = -1,
1065 .data = &ip22zilog_reg,
1066};
1067#endif /* CONFIG_SERIAL_IP22_ZILOG_CONSOLE */
1068
1069static struct uart_driver ip22zilog_reg = {
1070 .owner = THIS_MODULE,
1071 .driver_name = "serial",
1072 .dev_name = "ttyS",
1073 .major = TTY_MAJOR,
1074 .minor = 64,
1075 .nr = NUM_CHANNELS,
1076#ifdef CONFIG_SERIAL_IP22_ZILOG_CONSOLE
1077 .cons = &ip22zilog_console,
1078#endif
1079};
1080
1081static void __init ip22zilog_prepare(void)
1082{
1083 struct uart_ip22zilog_port *up;
1084 struct zilog_layout *rp;
1085 int channel, chip;
1086
1087 /*
1088 * Temporary fix.
1089 */
1090 for (channel = 0; channel < NUM_CHANNELS; channel++)
1091 spin_lock_init(&ip22zilog_port_table[channel].port.lock);
1092
1093 ip22zilog_irq_chain = &ip22zilog_port_table[NUM_CHANNELS - 1];
1094 up = &ip22zilog_port_table[0];
1095 for (channel = NUM_CHANNELS - 1 ; channel > 0; channel--)
1096 up[channel].next = &up[channel - 1];
1097 up[channel].next = NULL;
1098
1099 for (chip = 0; chip < NUM_IP22ZILOG; chip++) {
1100 if (!ip22zilog_chip_regs[chip]) {
1101 ip22zilog_chip_regs[chip] = rp = get_zs(chip);
1102
1103 up[(chip * 2) + 0].port.membase = (char *) &rp->channelB;
1104 up[(chip * 2) + 1].port.membase = (char *) &rp->channelA;
1105
1106 /* In theory mapbase is the physical address ... */
1107 up[(chip * 2) + 0].port.mapbase =
1108 (unsigned long) ioremap((unsigned long) &rp->channelB, 8);
1109 up[(chip * 2) + 1].port.mapbase =
1110 (unsigned long) ioremap((unsigned long) &rp->channelA, 8);
1111 }
1112
1113 /* Channel A */
1114 up[(chip * 2) + 0].port.iotype = UPIO_MEM;
1115 up[(chip * 2) + 0].port.irq = zilog_irq;
1116 up[(chip * 2) + 0].port.uartclk = ZS_CLOCK;
1117 up[(chip * 2) + 0].port.fifosize = 1;
1118 up[(chip * 2) + 0].port.ops = &ip22zilog_pops;
1119 up[(chip * 2) + 0].port.type = PORT_IP22ZILOG;
1120 up[(chip * 2) + 0].port.flags = 0;
1121 up[(chip * 2) + 0].port.line = (chip * 2) + 0;
1122 up[(chip * 2) + 0].flags = 0;
1123
1124 /* Channel B */
1125 up[(chip * 2) + 1].port.iotype = UPIO_MEM;
1126 up[(chip * 2) + 1].port.irq = zilog_irq;
1127 up[(chip * 2) + 1].port.uartclk = ZS_CLOCK;
1128 up[(chip * 2) + 1].port.fifosize = 1;
1129 up[(chip * 2) + 1].port.ops = &ip22zilog_pops;
1130 up[(chip * 2) + 1].port.type = PORT_IP22ZILOG;
1131 up[(chip * 2) + 1].port.line = (chip * 2) + 1;
1132 up[(chip * 2) + 1].flags |= IP22ZILOG_FLAG_IS_CHANNEL_A;
1133 }
1134
1135 for (channel = 0; channel < NUM_CHANNELS; channel++) {
1136 struct uart_ip22zilog_port *up = &ip22zilog_port_table[channel];
1137 int brg;
1138
1139 /* Normal serial TTY. */
1140 up->parity_mask = 0xff;
1141 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1142 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1143 up->curregs[R3] = RxENAB | Rx8;
1144 up->curregs[R5] = TxENAB | Tx8;
1145 up->curregs[R9] = NV | MIE;
1146 up->curregs[R10] = NRZ;
1147 up->curregs[R11] = TCBR | RCBR;
1148 brg = BPS_TO_BRG(9600, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1149 up->curregs[R12] = (brg & 0xff);
1150 up->curregs[R13] = (brg >> 8) & 0xff;
1151 up->curregs[R14] = BRENAB;
1152 }
1153}
1154
1155static int __init ip22zilog_ports_init(void)
1156{
1157 int ret;
1158
1159 printk(KERN_INFO "Serial: IP22 Zilog driver (%d chips).\n", NUM_IP22ZILOG);
1160
1161 ip22zilog_prepare();
1162
1163 if (request_irq(zilog_irq, ip22zilog_interrupt, 0,
1164 "IP22-Zilog", ip22zilog_irq_chain)) {
1165 panic("IP22-Zilog: Unable to register zs interrupt handler.\n");
1166 }
1167
1168 ret = uart_register_driver(&ip22zilog_reg);
1169 if (ret == 0) {
1170 int i;
1171
1172 for (i = 0; i < NUM_CHANNELS; i++) {
1173 struct uart_ip22zilog_port *up = &ip22zilog_port_table[i];
1174
1175 uart_add_one_port(&ip22zilog_reg, &up->port);
1176 }
1177 }
1178
1179 return ret;
1180}
1181
1182static int __init ip22zilog_init(void)
1183{
1184 /* IP22 Zilog setup is hard coded, no probing to do. */
1185 ip22zilog_alloc_tables();
1186 ip22zilog_ports_init();
1187
1188 return 0;
1189}
1190
1191static void __exit ip22zilog_exit(void)
1192{
1193 int i;
1194 struct uart_ip22zilog_port *up;
1195
1196 for (i = 0; i < NUM_CHANNELS; i++) {
1197 up = &ip22zilog_port_table[i];
1198
1199 uart_remove_one_port(&ip22zilog_reg, &up->port);
1200 }
1201
1202 /* Free IO mem */
1203 up = &ip22zilog_port_table[0];
1204 for (i = 0; i < NUM_IP22ZILOG; i++) {
1205 if (up[(i * 2) + 0].port.mapbase) {
1206 iounmap((void*)up[(i * 2) + 0].port.mapbase);
1207 up[(i * 2) + 0].port.mapbase = 0;
1208 }
1209 if (up[(i * 2) + 1].port.mapbase) {
1210 iounmap((void*)up[(i * 2) + 1].port.mapbase);
1211 up[(i * 2) + 1].port.mapbase = 0;
1212 }
1213 }
1214
1215 uart_unregister_driver(&ip22zilog_reg);
1216}
1217
1218module_init(ip22zilog_init);
1219module_exit(ip22zilog_exit);
1220
1221/* David wrote it but I'm to blame for the bugs ... */
1222MODULE_AUTHOR("Ralf Baechle <ralf@linux-mips.org>");
1223MODULE_DESCRIPTION("SGI Zilog serial port driver");
1224MODULE_LICENSE("GPL");
1/*
2 * Driver for Zilog serial chips found on SGI workstations and
3 * servers. This driver could actually be made more generic.
4 *
5 * This is based on the drivers/serial/sunzilog.c code as of 2.6.0-test7 and the
6 * old drivers/sgi/char/sgiserial.c code which itself is based of the original
7 * drivers/sbus/char/zs.c code. A lot of code has been simply moved over
8 * directly from there but much has been rewritten. Credits therefore go out
9 * to David S. Miller, Eddie C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell
10 * for their work there.
11 *
12 * Copyright (C) 2002 Ralf Baechle (ralf@linux-mips.org)
13 * Copyright (C) 2002 David S. Miller (davem@redhat.com)
14 */
15#include <linux/module.h>
16#include <linux/kernel.h>
17#include <linux/errno.h>
18#include <linux/delay.h>
19#include <linux/tty.h>
20#include <linux/tty_flip.h>
21#include <linux/major.h>
22#include <linux/string.h>
23#include <linux/ptrace.h>
24#include <linux/ioport.h>
25#include <linux/slab.h>
26#include <linux/circ_buf.h>
27#include <linux/serial.h>
28#include <linux/sysrq.h>
29#include <linux/console.h>
30#include <linux/spinlock.h>
31#include <linux/init.h>
32
33#include <asm/io.h>
34#include <asm/irq.h>
35#include <asm/sgialib.h>
36#include <asm/sgi/ioc.h>
37#include <asm/sgi/hpc3.h>
38#include <asm/sgi/ip22.h>
39
40#if defined(CONFIG_SERIAL_IP22_ZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
41#define SUPPORT_SYSRQ
42#endif
43
44#include <linux/serial_core.h>
45
46#include "ip22zilog.h"
47
48/*
49 * On IP22 we need to delay after register accesses but we do not need to
50 * flush writes.
51 */
52#define ZSDELAY() udelay(5)
53#define ZSDELAY_LONG() udelay(20)
54#define ZS_WSYNC(channel) do { } while (0)
55
56#define NUM_IP22ZILOG 1
57#define NUM_CHANNELS (NUM_IP22ZILOG * 2)
58
59#define ZS_CLOCK 3672000 /* Zilog input clock rate. */
60#define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */
61
62/*
63 * We wrap our port structure around the generic uart_port.
64 */
65struct uart_ip22zilog_port {
66 struct uart_port port;
67
68 /* IRQ servicing chain. */
69 struct uart_ip22zilog_port *next;
70
71 /* Current values of Zilog write registers. */
72 unsigned char curregs[NUM_ZSREGS];
73
74 unsigned int flags;
75#define IP22ZILOG_FLAG_IS_CONS 0x00000004
76#define IP22ZILOG_FLAG_IS_KGDB 0x00000008
77#define IP22ZILOG_FLAG_MODEM_STATUS 0x00000010
78#define IP22ZILOG_FLAG_IS_CHANNEL_A 0x00000020
79#define IP22ZILOG_FLAG_REGS_HELD 0x00000040
80#define IP22ZILOG_FLAG_TX_STOPPED 0x00000080
81#define IP22ZILOG_FLAG_TX_ACTIVE 0x00000100
82#define IP22ZILOG_FLAG_RESET_DONE 0x00000200
83
84 unsigned int tty_break;
85
86 unsigned char parity_mask;
87 unsigned char prev_status;
88};
89
90#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel *)((PORT)->membase))
91#define UART_ZILOG(PORT) ((struct uart_ip22zilog_port *)(PORT))
92#define IP22ZILOG_GET_CURR_REG(PORT, REGNUM) \
93 (UART_ZILOG(PORT)->curregs[REGNUM])
94#define IP22ZILOG_SET_CURR_REG(PORT, REGNUM, REGVAL) \
95 ((UART_ZILOG(PORT)->curregs[REGNUM]) = (REGVAL))
96#define ZS_IS_CONS(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CONS)
97#define ZS_IS_KGDB(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_KGDB)
98#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & IP22ZILOG_FLAG_MODEM_STATUS)
99#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CHANNEL_A)
100#define ZS_REGS_HELD(UP) ((UP)->flags & IP22ZILOG_FLAG_REGS_HELD)
101#define ZS_TX_STOPPED(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_STOPPED)
102#define ZS_TX_ACTIVE(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_ACTIVE)
103
104/* Reading and writing Zilog8530 registers. The delays are to make this
105 * driver work on the IP22 which needs a settling delay after each chip
106 * register access, other machines handle this in hardware via auxiliary
107 * flip-flops which implement the settle time we do in software.
108 *
109 * The port lock must be held and local IRQs must be disabled
110 * when {read,write}_zsreg is invoked.
111 */
112static unsigned char read_zsreg(struct zilog_channel *channel,
113 unsigned char reg)
114{
115 unsigned char retval;
116
117 writeb(reg, &channel->control);
118 ZSDELAY();
119 retval = readb(&channel->control);
120 ZSDELAY();
121
122 return retval;
123}
124
125static void write_zsreg(struct zilog_channel *channel,
126 unsigned char reg, unsigned char value)
127{
128 writeb(reg, &channel->control);
129 ZSDELAY();
130 writeb(value, &channel->control);
131 ZSDELAY();
132}
133
134static void ip22zilog_clear_fifo(struct zilog_channel *channel)
135{
136 int i;
137
138 for (i = 0; i < 32; i++) {
139 unsigned char regval;
140
141 regval = readb(&channel->control);
142 ZSDELAY();
143 if (regval & Rx_CH_AV)
144 break;
145
146 regval = read_zsreg(channel, R1);
147 readb(&channel->data);
148 ZSDELAY();
149
150 if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) {
151 writeb(ERR_RES, &channel->control);
152 ZSDELAY();
153 ZS_WSYNC(channel);
154 }
155 }
156}
157
158/* This function must only be called when the TX is not busy. The UART
159 * port lock must be held and local interrupts disabled.
160 */
161static void __load_zsregs(struct zilog_channel *channel, unsigned char *regs)
162{
163 int i;
164
165 /* Let pending transmits finish. */
166 for (i = 0; i < 1000; i++) {
167 unsigned char stat = read_zsreg(channel, R1);
168 if (stat & ALL_SNT)
169 break;
170 udelay(100);
171 }
172
173 writeb(ERR_RES, &channel->control);
174 ZSDELAY();
175 ZS_WSYNC(channel);
176
177 ip22zilog_clear_fifo(channel);
178
179 /* Disable all interrupts. */
180 write_zsreg(channel, R1,
181 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
182
183 /* Set parity, sync config, stop bits, and clock divisor. */
184 write_zsreg(channel, R4, regs[R4]);
185
186 /* Set misc. TX/RX control bits. */
187 write_zsreg(channel, R10, regs[R10]);
188
189 /* Set TX/RX controls sans the enable bits. */
190 write_zsreg(channel, R3, regs[R3] & ~RxENAB);
191 write_zsreg(channel, R5, regs[R5] & ~TxENAB);
192
193 /* Synchronous mode config. */
194 write_zsreg(channel, R6, regs[R6]);
195 write_zsreg(channel, R7, regs[R7]);
196
197 /* Don't mess with the interrupt vector (R2, unused by us) and
198 * master interrupt control (R9). We make sure this is setup
199 * properly at probe time then never touch it again.
200 */
201
202 /* Disable baud generator. */
203 write_zsreg(channel, R14, regs[R14] & ~BRENAB);
204
205 /* Clock mode control. */
206 write_zsreg(channel, R11, regs[R11]);
207
208 /* Lower and upper byte of baud rate generator divisor. */
209 write_zsreg(channel, R12, regs[R12]);
210 write_zsreg(channel, R13, regs[R13]);
211
212 /* Now rewrite R14, with BRENAB (if set). */
213 write_zsreg(channel, R14, regs[R14]);
214
215 /* External status interrupt control. */
216 write_zsreg(channel, R15, regs[R15]);
217
218 /* Reset external status interrupts. */
219 write_zsreg(channel, R0, RES_EXT_INT);
220 write_zsreg(channel, R0, RES_EXT_INT);
221
222 /* Rewrite R3/R5, this time without enables masked. */
223 write_zsreg(channel, R3, regs[R3]);
224 write_zsreg(channel, R5, regs[R5]);
225
226 /* Rewrite R1, this time without IRQ enabled masked. */
227 write_zsreg(channel, R1, regs[R1]);
228}
229
230/* Reprogram the Zilog channel HW registers with the copies found in the
231 * software state struct. If the transmitter is busy, we defer this update
232 * until the next TX complete interrupt. Else, we do it right now.
233 *
234 * The UART port lock must be held and local interrupts disabled.
235 */
236static void ip22zilog_maybe_update_regs(struct uart_ip22zilog_port *up,
237 struct zilog_channel *channel)
238{
239 if (!ZS_REGS_HELD(up)) {
240 if (ZS_TX_ACTIVE(up)) {
241 up->flags |= IP22ZILOG_FLAG_REGS_HELD;
242 } else {
243 __load_zsregs(channel, up->curregs);
244 }
245 }
246}
247
248#define Rx_BRK 0x0100 /* BREAK event software flag. */
249#define Rx_SYS 0x0200 /* SysRq event software flag. */
250
251static struct tty_struct *ip22zilog_receive_chars(struct uart_ip22zilog_port *up,
252 struct zilog_channel *channel)
253{
254 struct tty_struct *tty;
255 unsigned char ch, flag;
256 unsigned int r1;
257
258 tty = NULL;
259 if (up->port.state != NULL &&
260 up->port.state->port.tty != NULL)
261 tty = up->port.state->port.tty;
262
263 for (;;) {
264 ch = readb(&channel->control);
265 ZSDELAY();
266 if (!(ch & Rx_CH_AV))
267 break;
268
269 r1 = read_zsreg(channel, R1);
270 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
271 writeb(ERR_RES, &channel->control);
272 ZSDELAY();
273 ZS_WSYNC(channel);
274 }
275
276 ch = readb(&channel->data);
277 ZSDELAY();
278
279 ch &= up->parity_mask;
280
281 /* Handle the null char got when BREAK is removed. */
282 if (!ch)
283 r1 |= up->tty_break;
284
285 /* A real serial line, record the character and status. */
286 flag = TTY_NORMAL;
287 up->port.icount.rx++;
288 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR | Rx_SYS | Rx_BRK)) {
289 up->tty_break = 0;
290
291 if (r1 & (Rx_SYS | Rx_BRK)) {
292 up->port.icount.brk++;
293 if (r1 & Rx_SYS)
294 continue;
295 r1 &= ~(PAR_ERR | CRC_ERR);
296 }
297 else if (r1 & PAR_ERR)
298 up->port.icount.parity++;
299 else if (r1 & CRC_ERR)
300 up->port.icount.frame++;
301 if (r1 & Rx_OVR)
302 up->port.icount.overrun++;
303 r1 &= up->port.read_status_mask;
304 if (r1 & Rx_BRK)
305 flag = TTY_BREAK;
306 else if (r1 & PAR_ERR)
307 flag = TTY_PARITY;
308 else if (r1 & CRC_ERR)
309 flag = TTY_FRAME;
310 }
311
312 if (uart_handle_sysrq_char(&up->port, ch))
313 continue;
314
315 if (tty)
316 uart_insert_char(&up->port, r1, Rx_OVR, ch, flag);
317 }
318 return tty;
319}
320
321static void ip22zilog_status_handle(struct uart_ip22zilog_port *up,
322 struct zilog_channel *channel)
323{
324 unsigned char status;
325
326 status = readb(&channel->control);
327 ZSDELAY();
328
329 writeb(RES_EXT_INT, &channel->control);
330 ZSDELAY();
331 ZS_WSYNC(channel);
332
333 if (up->curregs[R15] & BRKIE) {
334 if ((status & BRK_ABRT) && !(up->prev_status & BRK_ABRT)) {
335 if (uart_handle_break(&up->port))
336 up->tty_break = Rx_SYS;
337 else
338 up->tty_break = Rx_BRK;
339 }
340 }
341
342 if (ZS_WANTS_MODEM_STATUS(up)) {
343 if (status & SYNC)
344 up->port.icount.dsr++;
345
346 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
347 * But it does not tell us which bit has changed, we have to keep
348 * track of this ourselves.
349 */
350 if ((status ^ up->prev_status) ^ DCD)
351 uart_handle_dcd_change(&up->port,
352 (status & DCD));
353 if ((status ^ up->prev_status) ^ CTS)
354 uart_handle_cts_change(&up->port,
355 (status & CTS));
356
357 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
358 }
359
360 up->prev_status = status;
361}
362
363static void ip22zilog_transmit_chars(struct uart_ip22zilog_port *up,
364 struct zilog_channel *channel)
365{
366 struct circ_buf *xmit;
367
368 if (ZS_IS_CONS(up)) {
369 unsigned char status = readb(&channel->control);
370 ZSDELAY();
371
372 /* TX still busy? Just wait for the next TX done interrupt.
373 *
374 * It can occur because of how we do serial console writes. It would
375 * be nice to transmit console writes just like we normally would for
376 * a TTY line. (ie. buffered and TX interrupt driven). That is not
377 * easy because console writes cannot sleep. One solution might be
378 * to poll on enough port->xmit space becoming free. -DaveM
379 */
380 if (!(status & Tx_BUF_EMP))
381 return;
382 }
383
384 up->flags &= ~IP22ZILOG_FLAG_TX_ACTIVE;
385
386 if (ZS_REGS_HELD(up)) {
387 __load_zsregs(channel, up->curregs);
388 up->flags &= ~IP22ZILOG_FLAG_REGS_HELD;
389 }
390
391 if (ZS_TX_STOPPED(up)) {
392 up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED;
393 goto ack_tx_int;
394 }
395
396 if (up->port.x_char) {
397 up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
398 writeb(up->port.x_char, &channel->data);
399 ZSDELAY();
400 ZS_WSYNC(channel);
401
402 up->port.icount.tx++;
403 up->port.x_char = 0;
404 return;
405 }
406
407 if (up->port.state == NULL)
408 goto ack_tx_int;
409 xmit = &up->port.state->xmit;
410 if (uart_circ_empty(xmit))
411 goto ack_tx_int;
412 if (uart_tx_stopped(&up->port))
413 goto ack_tx_int;
414
415 up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
416 writeb(xmit->buf[xmit->tail], &channel->data);
417 ZSDELAY();
418 ZS_WSYNC(channel);
419
420 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
421 up->port.icount.tx++;
422
423 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
424 uart_write_wakeup(&up->port);
425
426 return;
427
428ack_tx_int:
429 writeb(RES_Tx_P, &channel->control);
430 ZSDELAY();
431 ZS_WSYNC(channel);
432}
433
434static irqreturn_t ip22zilog_interrupt(int irq, void *dev_id)
435{
436 struct uart_ip22zilog_port *up = dev_id;
437
438 while (up) {
439 struct zilog_channel *channel
440 = ZILOG_CHANNEL_FROM_PORT(&up->port);
441 struct tty_struct *tty;
442 unsigned char r3;
443
444 spin_lock(&up->port.lock);
445 r3 = read_zsreg(channel, R3);
446
447 /* Channel A */
448 tty = NULL;
449 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
450 writeb(RES_H_IUS, &channel->control);
451 ZSDELAY();
452 ZS_WSYNC(channel);
453
454 if (r3 & CHARxIP)
455 tty = ip22zilog_receive_chars(up, channel);
456 if (r3 & CHAEXT)
457 ip22zilog_status_handle(up, channel);
458 if (r3 & CHATxIP)
459 ip22zilog_transmit_chars(up, channel);
460 }
461 spin_unlock(&up->port.lock);
462
463 if (tty)
464 tty_flip_buffer_push(tty);
465
466 /* Channel B */
467 up = up->next;
468 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
469
470 spin_lock(&up->port.lock);
471 tty = NULL;
472 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
473 writeb(RES_H_IUS, &channel->control);
474 ZSDELAY();
475 ZS_WSYNC(channel);
476
477 if (r3 & CHBRxIP)
478 tty = ip22zilog_receive_chars(up, channel);
479 if (r3 & CHBEXT)
480 ip22zilog_status_handle(up, channel);
481 if (r3 & CHBTxIP)
482 ip22zilog_transmit_chars(up, channel);
483 }
484 spin_unlock(&up->port.lock);
485
486 if (tty)
487 tty_flip_buffer_push(tty);
488
489 up = up->next;
490 }
491
492 return IRQ_HANDLED;
493}
494
495/* A convenient way to quickly get R0 status. The caller must _not_ hold the
496 * port lock, it is acquired here.
497 */
498static __inline__ unsigned char ip22zilog_read_channel_status(struct uart_port *port)
499{
500 struct zilog_channel *channel;
501 unsigned char status;
502
503 channel = ZILOG_CHANNEL_FROM_PORT(port);
504 status = readb(&channel->control);
505 ZSDELAY();
506
507 return status;
508}
509
510/* The port lock is not held. */
511static unsigned int ip22zilog_tx_empty(struct uart_port *port)
512{
513 unsigned long flags;
514 unsigned char status;
515 unsigned int ret;
516
517 spin_lock_irqsave(&port->lock, flags);
518
519 status = ip22zilog_read_channel_status(port);
520
521 spin_unlock_irqrestore(&port->lock, flags);
522
523 if (status & Tx_BUF_EMP)
524 ret = TIOCSER_TEMT;
525 else
526 ret = 0;
527
528 return ret;
529}
530
531/* The port lock is held and interrupts are disabled. */
532static unsigned int ip22zilog_get_mctrl(struct uart_port *port)
533{
534 unsigned char status;
535 unsigned int ret;
536
537 status = ip22zilog_read_channel_status(port);
538
539 ret = 0;
540 if (status & DCD)
541 ret |= TIOCM_CAR;
542 if (status & SYNC)
543 ret |= TIOCM_DSR;
544 if (status & CTS)
545 ret |= TIOCM_CTS;
546
547 return ret;
548}
549
550/* The port lock is held and interrupts are disabled. */
551static void ip22zilog_set_mctrl(struct uart_port *port, unsigned int mctrl)
552{
553 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
554 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
555 unsigned char set_bits, clear_bits;
556
557 set_bits = clear_bits = 0;
558
559 if (mctrl & TIOCM_RTS)
560 set_bits |= RTS;
561 else
562 clear_bits |= RTS;
563 if (mctrl & TIOCM_DTR)
564 set_bits |= DTR;
565 else
566 clear_bits |= DTR;
567
568 /* NOTE: Not subject to 'transmitter active' rule. */
569 up->curregs[R5] |= set_bits;
570 up->curregs[R5] &= ~clear_bits;
571 write_zsreg(channel, R5, up->curregs[R5]);
572}
573
574/* The port lock is held and interrupts are disabled. */
575static void ip22zilog_stop_tx(struct uart_port *port)
576{
577 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
578
579 up->flags |= IP22ZILOG_FLAG_TX_STOPPED;
580}
581
582/* The port lock is held and interrupts are disabled. */
583static void ip22zilog_start_tx(struct uart_port *port)
584{
585 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
586 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
587 unsigned char status;
588
589 up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
590 up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED;
591
592 status = readb(&channel->control);
593 ZSDELAY();
594
595 /* TX busy? Just wait for the TX done interrupt. */
596 if (!(status & Tx_BUF_EMP))
597 return;
598
599 /* Send the first character to jump-start the TX done
600 * IRQ sending engine.
601 */
602 if (port->x_char) {
603 writeb(port->x_char, &channel->data);
604 ZSDELAY();
605 ZS_WSYNC(channel);
606
607 port->icount.tx++;
608 port->x_char = 0;
609 } else {
610 struct circ_buf *xmit = &port->state->xmit;
611
612 writeb(xmit->buf[xmit->tail], &channel->data);
613 ZSDELAY();
614 ZS_WSYNC(channel);
615
616 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
617 port->icount.tx++;
618
619 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
620 uart_write_wakeup(&up->port);
621 }
622}
623
624/* The port lock is held and interrupts are disabled. */
625static void ip22zilog_stop_rx(struct uart_port *port)
626{
627 struct uart_ip22zilog_port *up = UART_ZILOG(port);
628 struct zilog_channel *channel;
629
630 if (ZS_IS_CONS(up))
631 return;
632
633 channel = ZILOG_CHANNEL_FROM_PORT(port);
634
635 /* Disable all RX interrupts. */
636 up->curregs[R1] &= ~RxINT_MASK;
637 ip22zilog_maybe_update_regs(up, channel);
638}
639
640/* The port lock is held. */
641static void ip22zilog_enable_ms(struct uart_port *port)
642{
643 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
644 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
645 unsigned char new_reg;
646
647 new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
648 if (new_reg != up->curregs[R15]) {
649 up->curregs[R15] = new_reg;
650
651 /* NOTE: Not subject to 'transmitter active' rule. */
652 write_zsreg(channel, R15, up->curregs[R15]);
653 }
654}
655
656/* The port lock is not held. */
657static void ip22zilog_break_ctl(struct uart_port *port, int break_state)
658{
659 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
660 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
661 unsigned char set_bits, clear_bits, new_reg;
662 unsigned long flags;
663
664 set_bits = clear_bits = 0;
665
666 if (break_state)
667 set_bits |= SND_BRK;
668 else
669 clear_bits |= SND_BRK;
670
671 spin_lock_irqsave(&port->lock, flags);
672
673 new_reg = (up->curregs[R5] | set_bits) & ~clear_bits;
674 if (new_reg != up->curregs[R5]) {
675 up->curregs[R5] = new_reg;
676
677 /* NOTE: Not subject to 'transmitter active' rule. */
678 write_zsreg(channel, R5, up->curregs[R5]);
679 }
680
681 spin_unlock_irqrestore(&port->lock, flags);
682}
683
684static void __ip22zilog_reset(struct uart_ip22zilog_port *up)
685{
686 struct zilog_channel *channel;
687 int i;
688
689 if (up->flags & IP22ZILOG_FLAG_RESET_DONE)
690 return;
691
692 /* Let pending transmits finish. */
693 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
694 for (i = 0; i < 1000; i++) {
695 unsigned char stat = read_zsreg(channel, R1);
696 if (stat & ALL_SNT)
697 break;
698 udelay(100);
699 }
700
701 if (!ZS_IS_CHANNEL_A(up)) {
702 up++;
703 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
704 }
705 write_zsreg(channel, R9, FHWRES);
706 ZSDELAY_LONG();
707 (void) read_zsreg(channel, R0);
708
709 up->flags |= IP22ZILOG_FLAG_RESET_DONE;
710 up->next->flags |= IP22ZILOG_FLAG_RESET_DONE;
711}
712
713static void __ip22zilog_startup(struct uart_ip22zilog_port *up)
714{
715 struct zilog_channel *channel;
716
717 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
718
719 __ip22zilog_reset(up);
720
721 __load_zsregs(channel, up->curregs);
722 /* set master interrupt enable */
723 write_zsreg(channel, R9, up->curregs[R9]);
724 up->prev_status = readb(&channel->control);
725
726 /* Enable receiver and transmitter. */
727 up->curregs[R3] |= RxENAB;
728 up->curregs[R5] |= TxENAB;
729
730 up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
731 ip22zilog_maybe_update_regs(up, channel);
732}
733
734static int ip22zilog_startup(struct uart_port *port)
735{
736 struct uart_ip22zilog_port *up = UART_ZILOG(port);
737 unsigned long flags;
738
739 if (ZS_IS_CONS(up))
740 return 0;
741
742 spin_lock_irqsave(&port->lock, flags);
743 __ip22zilog_startup(up);
744 spin_unlock_irqrestore(&port->lock, flags);
745 return 0;
746}
747
748/*
749 * The test for ZS_IS_CONS is explained by the following e-mail:
750 *****
751 * From: Russell King <rmk@arm.linux.org.uk>
752 * Date: Sun, 8 Dec 2002 10:18:38 +0000
753 *
754 * On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote:
755 * > I boot my 2.5 boxes using "console=ttyS0,9600" argument,
756 * > and I noticed that something is not right with reference
757 * > counting in this case. It seems that when the console
758 * > is open by kernel initially, this is not accounted
759 * > as an open, and uart_startup is not called.
760 *
761 * That is correct. We are unable to call uart_startup when the serial
762 * console is initialised because it may need to allocate memory (as
763 * request_irq does) and the memory allocators may not have been
764 * initialised.
765 *
766 * 1. initialise the port into a state where it can send characters in the
767 * console write method.
768 *
769 * 2. don't do the actual hardware shutdown in your shutdown() method (but
770 * do the normal software shutdown - ie, free irqs etc)
771 *****
772 */
773static void ip22zilog_shutdown(struct uart_port *port)
774{
775 struct uart_ip22zilog_port *up = UART_ZILOG(port);
776 struct zilog_channel *channel;
777 unsigned long flags;
778
779 if (ZS_IS_CONS(up))
780 return;
781
782 spin_lock_irqsave(&port->lock, flags);
783
784 channel = ZILOG_CHANNEL_FROM_PORT(port);
785
786 /* Disable receiver and transmitter. */
787 up->curregs[R3] &= ~RxENAB;
788 up->curregs[R5] &= ~TxENAB;
789
790 /* Disable all interrupts and BRK assertion. */
791 up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
792 up->curregs[R5] &= ~SND_BRK;
793 ip22zilog_maybe_update_regs(up, channel);
794
795 spin_unlock_irqrestore(&port->lock, flags);
796}
797
798/* Shared by TTY driver and serial console setup. The port lock is held
799 * and local interrupts are disabled.
800 */
801static void
802ip22zilog_convert_to_zs(struct uart_ip22zilog_port *up, unsigned int cflag,
803 unsigned int iflag, int brg)
804{
805
806 up->curregs[R10] = NRZ;
807 up->curregs[R11] = TCBR | RCBR;
808
809 /* Program BAUD and clock source. */
810 up->curregs[R4] &= ~XCLK_MASK;
811 up->curregs[R4] |= X16CLK;
812 up->curregs[R12] = brg & 0xff;
813 up->curregs[R13] = (brg >> 8) & 0xff;
814 up->curregs[R14] = BRENAB;
815
816 /* Character size, stop bits, and parity. */
817 up->curregs[3] &= ~RxN_MASK;
818 up->curregs[5] &= ~TxN_MASK;
819 switch (cflag & CSIZE) {
820 case CS5:
821 up->curregs[3] |= Rx5;
822 up->curregs[5] |= Tx5;
823 up->parity_mask = 0x1f;
824 break;
825 case CS6:
826 up->curregs[3] |= Rx6;
827 up->curregs[5] |= Tx6;
828 up->parity_mask = 0x3f;
829 break;
830 case CS7:
831 up->curregs[3] |= Rx7;
832 up->curregs[5] |= Tx7;
833 up->parity_mask = 0x7f;
834 break;
835 case CS8:
836 default:
837 up->curregs[3] |= Rx8;
838 up->curregs[5] |= Tx8;
839 up->parity_mask = 0xff;
840 break;
841 };
842 up->curregs[4] &= ~0x0c;
843 if (cflag & CSTOPB)
844 up->curregs[4] |= SB2;
845 else
846 up->curregs[4] |= SB1;
847 if (cflag & PARENB)
848 up->curregs[4] |= PAR_ENAB;
849 else
850 up->curregs[4] &= ~PAR_ENAB;
851 if (!(cflag & PARODD))
852 up->curregs[4] |= PAR_EVEN;
853 else
854 up->curregs[4] &= ~PAR_EVEN;
855
856 up->port.read_status_mask = Rx_OVR;
857 if (iflag & INPCK)
858 up->port.read_status_mask |= CRC_ERR | PAR_ERR;
859 if (iflag & (BRKINT | PARMRK))
860 up->port.read_status_mask |= BRK_ABRT;
861
862 up->port.ignore_status_mask = 0;
863 if (iflag & IGNPAR)
864 up->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
865 if (iflag & IGNBRK) {
866 up->port.ignore_status_mask |= BRK_ABRT;
867 if (iflag & IGNPAR)
868 up->port.ignore_status_mask |= Rx_OVR;
869 }
870
871 if ((cflag & CREAD) == 0)
872 up->port.ignore_status_mask = 0xff;
873}
874
875/* The port lock is not held. */
876static void
877ip22zilog_set_termios(struct uart_port *port, struct ktermios *termios,
878 struct ktermios *old)
879{
880 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
881 unsigned long flags;
882 int baud, brg;
883
884 baud = uart_get_baud_rate(port, termios, old, 1200, 76800);
885
886 spin_lock_irqsave(&up->port.lock, flags);
887
888 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
889
890 ip22zilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg);
891
892 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
893 up->flags |= IP22ZILOG_FLAG_MODEM_STATUS;
894 else
895 up->flags &= ~IP22ZILOG_FLAG_MODEM_STATUS;
896
897 ip22zilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port));
898 uart_update_timeout(port, termios->c_cflag, baud);
899
900 spin_unlock_irqrestore(&up->port.lock, flags);
901}
902
903static const char *ip22zilog_type(struct uart_port *port)
904{
905 return "IP22-Zilog";
906}
907
908/* We do not request/release mappings of the registers here, this
909 * happens at early serial probe time.
910 */
911static void ip22zilog_release_port(struct uart_port *port)
912{
913}
914
915static int ip22zilog_request_port(struct uart_port *port)
916{
917 return 0;
918}
919
920/* These do not need to do anything interesting either. */
921static void ip22zilog_config_port(struct uart_port *port, int flags)
922{
923}
924
925/* We do not support letting the user mess with the divisor, IRQ, etc. */
926static int ip22zilog_verify_port(struct uart_port *port, struct serial_struct *ser)
927{
928 return -EINVAL;
929}
930
931static struct uart_ops ip22zilog_pops = {
932 .tx_empty = ip22zilog_tx_empty,
933 .set_mctrl = ip22zilog_set_mctrl,
934 .get_mctrl = ip22zilog_get_mctrl,
935 .stop_tx = ip22zilog_stop_tx,
936 .start_tx = ip22zilog_start_tx,
937 .stop_rx = ip22zilog_stop_rx,
938 .enable_ms = ip22zilog_enable_ms,
939 .break_ctl = ip22zilog_break_ctl,
940 .startup = ip22zilog_startup,
941 .shutdown = ip22zilog_shutdown,
942 .set_termios = ip22zilog_set_termios,
943 .type = ip22zilog_type,
944 .release_port = ip22zilog_release_port,
945 .request_port = ip22zilog_request_port,
946 .config_port = ip22zilog_config_port,
947 .verify_port = ip22zilog_verify_port,
948};
949
950static struct uart_ip22zilog_port *ip22zilog_port_table;
951static struct zilog_layout **ip22zilog_chip_regs;
952
953static struct uart_ip22zilog_port *ip22zilog_irq_chain;
954static int zilog_irq = -1;
955
956static void * __init alloc_one_table(unsigned long size)
957{
958 return kzalloc(size, GFP_KERNEL);
959}
960
961static void __init ip22zilog_alloc_tables(void)
962{
963 ip22zilog_port_table = (struct uart_ip22zilog_port *)
964 alloc_one_table(NUM_CHANNELS * sizeof(struct uart_ip22zilog_port));
965 ip22zilog_chip_regs = (struct zilog_layout **)
966 alloc_one_table(NUM_IP22ZILOG * sizeof(struct zilog_layout *));
967
968 if (ip22zilog_port_table == NULL || ip22zilog_chip_regs == NULL) {
969 panic("IP22-Zilog: Cannot allocate IP22-Zilog tables.");
970 }
971}
972
973/* Get the address of the registers for IP22-Zilog instance CHIP. */
974static struct zilog_layout * __init get_zs(int chip)
975{
976 unsigned long base;
977
978 if (chip < 0 || chip >= NUM_IP22ZILOG) {
979 panic("IP22-Zilog: Illegal chip number %d in get_zs.", chip);
980 }
981
982 /* Not probe-able, hard code it. */
983 base = (unsigned long) &sgioc->uart;
984
985 zilog_irq = SGI_SERIAL_IRQ;
986 request_mem_region(base, 8, "IP22-Zilog");
987
988 return (struct zilog_layout *) base;
989}
990
991#define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */
992
993#ifdef CONFIG_SERIAL_IP22_ZILOG_CONSOLE
994static void ip22zilog_put_char(struct uart_port *port, int ch)
995{
996 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
997 int loops = ZS_PUT_CHAR_MAX_DELAY;
998
999 /* This is a timed polling loop so do not switch the explicit
1000 * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM
1001 */
1002 do {
1003 unsigned char val = readb(&channel->control);
1004 if (val & Tx_BUF_EMP) {
1005 ZSDELAY();
1006 break;
1007 }
1008 udelay(5);
1009 } while (--loops);
1010
1011 writeb(ch, &channel->data);
1012 ZSDELAY();
1013 ZS_WSYNC(channel);
1014}
1015
1016static void
1017ip22zilog_console_write(struct console *con, const char *s, unsigned int count)
1018{
1019 struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index];
1020 unsigned long flags;
1021
1022 spin_lock_irqsave(&up->port.lock, flags);
1023 uart_console_write(&up->port, s, count, ip22zilog_put_char);
1024 udelay(2);
1025 spin_unlock_irqrestore(&up->port.lock, flags);
1026}
1027
1028static int __init ip22zilog_console_setup(struct console *con, char *options)
1029{
1030 struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index];
1031 unsigned long flags;
1032 int baud = 9600, bits = 8;
1033 int parity = 'n';
1034 int flow = 'n';
1035
1036 up->flags |= IP22ZILOG_FLAG_IS_CONS;
1037
1038 printk(KERN_INFO "Console: ttyS%d (IP22-Zilog)\n", con->index);
1039
1040 spin_lock_irqsave(&up->port.lock, flags);
1041
1042 up->curregs[R15] |= BRKIE;
1043
1044 __ip22zilog_startup(up);
1045
1046 spin_unlock_irqrestore(&up->port.lock, flags);
1047
1048 if (options)
1049 uart_parse_options(options, &baud, &parity, &bits, &flow);
1050 return uart_set_options(&up->port, con, baud, parity, bits, flow);
1051}
1052
1053static struct uart_driver ip22zilog_reg;
1054
1055static struct console ip22zilog_console = {
1056 .name = "ttyS",
1057 .write = ip22zilog_console_write,
1058 .device = uart_console_device,
1059 .setup = ip22zilog_console_setup,
1060 .flags = CON_PRINTBUFFER,
1061 .index = -1,
1062 .data = &ip22zilog_reg,
1063};
1064#endif /* CONFIG_SERIAL_IP22_ZILOG_CONSOLE */
1065
1066static struct uart_driver ip22zilog_reg = {
1067 .owner = THIS_MODULE,
1068 .driver_name = "serial",
1069 .dev_name = "ttyS",
1070 .major = TTY_MAJOR,
1071 .minor = 64,
1072 .nr = NUM_CHANNELS,
1073#ifdef CONFIG_SERIAL_IP22_ZILOG_CONSOLE
1074 .cons = &ip22zilog_console,
1075#endif
1076};
1077
1078static void __init ip22zilog_prepare(void)
1079{
1080 struct uart_ip22zilog_port *up;
1081 struct zilog_layout *rp;
1082 int channel, chip;
1083
1084 /*
1085 * Temporary fix.
1086 */
1087 for (channel = 0; channel < NUM_CHANNELS; channel++)
1088 spin_lock_init(&ip22zilog_port_table[channel].port.lock);
1089
1090 ip22zilog_irq_chain = &ip22zilog_port_table[NUM_CHANNELS - 1];
1091 up = &ip22zilog_port_table[0];
1092 for (channel = NUM_CHANNELS - 1 ; channel > 0; channel--)
1093 up[channel].next = &up[channel - 1];
1094 up[channel].next = NULL;
1095
1096 for (chip = 0; chip < NUM_IP22ZILOG; chip++) {
1097 if (!ip22zilog_chip_regs[chip]) {
1098 ip22zilog_chip_regs[chip] = rp = get_zs(chip);
1099
1100 up[(chip * 2) + 0].port.membase = (char *) &rp->channelB;
1101 up[(chip * 2) + 1].port.membase = (char *) &rp->channelA;
1102
1103 /* In theory mapbase is the physical address ... */
1104 up[(chip * 2) + 0].port.mapbase =
1105 (unsigned long) ioremap((unsigned long) &rp->channelB, 8);
1106 up[(chip * 2) + 1].port.mapbase =
1107 (unsigned long) ioremap((unsigned long) &rp->channelA, 8);
1108 }
1109
1110 /* Channel A */
1111 up[(chip * 2) + 0].port.iotype = UPIO_MEM;
1112 up[(chip * 2) + 0].port.irq = zilog_irq;
1113 up[(chip * 2) + 0].port.uartclk = ZS_CLOCK;
1114 up[(chip * 2) + 0].port.fifosize = 1;
1115 up[(chip * 2) + 0].port.ops = &ip22zilog_pops;
1116 up[(chip * 2) + 0].port.type = PORT_IP22ZILOG;
1117 up[(chip * 2) + 0].port.flags = 0;
1118 up[(chip * 2) + 0].port.line = (chip * 2) + 0;
1119 up[(chip * 2) + 0].flags = 0;
1120
1121 /* Channel B */
1122 up[(chip * 2) + 1].port.iotype = UPIO_MEM;
1123 up[(chip * 2) + 1].port.irq = zilog_irq;
1124 up[(chip * 2) + 1].port.uartclk = ZS_CLOCK;
1125 up[(chip * 2) + 1].port.fifosize = 1;
1126 up[(chip * 2) + 1].port.ops = &ip22zilog_pops;
1127 up[(chip * 2) + 1].port.type = PORT_IP22ZILOG;
1128 up[(chip * 2) + 1].port.line = (chip * 2) + 1;
1129 up[(chip * 2) + 1].flags |= IP22ZILOG_FLAG_IS_CHANNEL_A;
1130 }
1131
1132 for (channel = 0; channel < NUM_CHANNELS; channel++) {
1133 struct uart_ip22zilog_port *up = &ip22zilog_port_table[channel];
1134 int brg;
1135
1136 /* Normal serial TTY. */
1137 up->parity_mask = 0xff;
1138 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1139 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1140 up->curregs[R3] = RxENAB | Rx8;
1141 up->curregs[R5] = TxENAB | Tx8;
1142 up->curregs[R9] = NV | MIE;
1143 up->curregs[R10] = NRZ;
1144 up->curregs[R11] = TCBR | RCBR;
1145 brg = BPS_TO_BRG(9600, ZS_CLOCK / ZS_CLOCK_DIVISOR);
1146 up->curregs[R12] = (brg & 0xff);
1147 up->curregs[R13] = (brg >> 8) & 0xff;
1148 up->curregs[R14] = BRENAB;
1149 }
1150}
1151
1152static int __init ip22zilog_ports_init(void)
1153{
1154 int ret;
1155
1156 printk(KERN_INFO "Serial: IP22 Zilog driver (%d chips).\n", NUM_IP22ZILOG);
1157
1158 ip22zilog_prepare();
1159
1160 if (request_irq(zilog_irq, ip22zilog_interrupt, 0,
1161 "IP22-Zilog", ip22zilog_irq_chain)) {
1162 panic("IP22-Zilog: Unable to register zs interrupt handler.\n");
1163 }
1164
1165 ret = uart_register_driver(&ip22zilog_reg);
1166 if (ret == 0) {
1167 int i;
1168
1169 for (i = 0; i < NUM_CHANNELS; i++) {
1170 struct uart_ip22zilog_port *up = &ip22zilog_port_table[i];
1171
1172 uart_add_one_port(&ip22zilog_reg, &up->port);
1173 }
1174 }
1175
1176 return ret;
1177}
1178
1179static int __init ip22zilog_init(void)
1180{
1181 /* IP22 Zilog setup is hard coded, no probing to do. */
1182 ip22zilog_alloc_tables();
1183 ip22zilog_ports_init();
1184
1185 return 0;
1186}
1187
1188static void __exit ip22zilog_exit(void)
1189{
1190 int i;
1191 struct uart_ip22zilog_port *up;
1192
1193 for (i = 0; i < NUM_CHANNELS; i++) {
1194 up = &ip22zilog_port_table[i];
1195
1196 uart_remove_one_port(&ip22zilog_reg, &up->port);
1197 }
1198
1199 /* Free IO mem */
1200 up = &ip22zilog_port_table[0];
1201 for (i = 0; i < NUM_IP22ZILOG; i++) {
1202 if (up[(i * 2) + 0].port.mapbase) {
1203 iounmap((void*)up[(i * 2) + 0].port.mapbase);
1204 up[(i * 2) + 0].port.mapbase = 0;
1205 }
1206 if (up[(i * 2) + 1].port.mapbase) {
1207 iounmap((void*)up[(i * 2) + 1].port.mapbase);
1208 up[(i * 2) + 1].port.mapbase = 0;
1209 }
1210 }
1211
1212 uart_unregister_driver(&ip22zilog_reg);
1213}
1214
1215module_init(ip22zilog_init);
1216module_exit(ip22zilog_exit);
1217
1218/* David wrote it but I'm to blame for the bugs ... */
1219MODULE_AUTHOR("Ralf Baechle <ralf@linux-mips.org>");
1220MODULE_DESCRIPTION("SGI Zilog serial port driver");
1221MODULE_LICENSE("GPL");