Loading...
1/* SPDX-License-Identifier: GPL-2.0-only */
2/*
3 * mac80211 <-> driver interface
4 *
5 * Copyright 2002-2005, Devicescape Software, Inc.
6 * Copyright 2006-2007 Jiri Benc <jbenc@suse.cz>
7 * Copyright 2007-2010 Johannes Berg <johannes@sipsolutions.net>
8 * Copyright 2013-2014 Intel Mobile Communications GmbH
9 * Copyright (C) 2015 - 2017 Intel Deutschland GmbH
10 * Copyright (C) 2018 - 2019 Intel Corporation
11 */
12
13#ifndef MAC80211_H
14#define MAC80211_H
15
16#include <linux/bug.h>
17#include <linux/kernel.h>
18#include <linux/if_ether.h>
19#include <linux/skbuff.h>
20#include <linux/ieee80211.h>
21#include <net/cfg80211.h>
22#include <net/codel.h>
23#include <net/ieee80211_radiotap.h>
24#include <asm/unaligned.h>
25
26/**
27 * DOC: Introduction
28 *
29 * mac80211 is the Linux stack for 802.11 hardware that implements
30 * only partial functionality in hard- or firmware. This document
31 * defines the interface between mac80211 and low-level hardware
32 * drivers.
33 */
34
35/**
36 * DOC: Calling mac80211 from interrupts
37 *
38 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
39 * called in hardware interrupt context. The low-level driver must not call any
40 * other functions in hardware interrupt context. If there is a need for such
41 * call, the low-level driver should first ACK the interrupt and perform the
42 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
43 * tasklet function.
44 *
45 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
46 * use the non-IRQ-safe functions!
47 */
48
49/**
50 * DOC: Warning
51 *
52 * If you're reading this document and not the header file itself, it will
53 * be incomplete because not all documentation has been converted yet.
54 */
55
56/**
57 * DOC: Frame format
58 *
59 * As a general rule, when frames are passed between mac80211 and the driver,
60 * they start with the IEEE 802.11 header and include the same octets that are
61 * sent over the air except for the FCS which should be calculated by the
62 * hardware.
63 *
64 * There are, however, various exceptions to this rule for advanced features:
65 *
66 * The first exception is for hardware encryption and decryption offload
67 * where the IV/ICV may or may not be generated in hardware.
68 *
69 * Secondly, when the hardware handles fragmentation, the frame handed to
70 * the driver from mac80211 is the MSDU, not the MPDU.
71 */
72
73/**
74 * DOC: mac80211 workqueue
75 *
76 * mac80211 provides its own workqueue for drivers and internal mac80211 use.
77 * The workqueue is a single threaded workqueue and can only be accessed by
78 * helpers for sanity checking. Drivers must ensure all work added onto the
79 * mac80211 workqueue should be cancelled on the driver stop() callback.
80 *
81 * mac80211 will flushed the workqueue upon interface removal and during
82 * suspend.
83 *
84 * All work performed on the mac80211 workqueue must not acquire the RTNL lock.
85 *
86 */
87
88/**
89 * DOC: mac80211 software tx queueing
90 *
91 * mac80211 provides an optional intermediate queueing implementation designed
92 * to allow the driver to keep hardware queues short and provide some fairness
93 * between different stations/interfaces.
94 * In this model, the driver pulls data frames from the mac80211 queue instead
95 * of letting mac80211 push them via drv_tx().
96 * Other frames (e.g. control or management) are still pushed using drv_tx().
97 *
98 * Drivers indicate that they use this model by implementing the .wake_tx_queue
99 * driver operation.
100 *
101 * Intermediate queues (struct ieee80211_txq) are kept per-sta per-tid, with
102 * another per-sta for non-data/non-mgmt and bufferable management frames, and
103 * a single per-vif queue for multicast data frames.
104 *
105 * The driver is expected to initialize its private per-queue data for stations
106 * and interfaces in the .add_interface and .sta_add ops.
107 *
108 * The driver can't access the queue directly. To dequeue a frame from a
109 * txq, it calls ieee80211_tx_dequeue(). Whenever mac80211 adds a new frame to a
110 * queue, it calls the .wake_tx_queue driver op.
111 *
112 * Drivers can optionally delegate responsibility for scheduling queues to
113 * mac80211, to take advantage of airtime fairness accounting. In this case, to
114 * obtain the next queue to pull frames from, the driver calls
115 * ieee80211_next_txq(). The driver is then expected to return the txq using
116 * ieee80211_return_txq().
117 *
118 * For AP powersave TIM handling, the driver only needs to indicate if it has
119 * buffered packets in the driver specific data structures by calling
120 * ieee80211_sta_set_buffered(). For frames buffered in the ieee80211_txq
121 * struct, mac80211 sets the appropriate TIM PVB bits and calls
122 * .release_buffered_frames().
123 * In that callback the driver is therefore expected to release its own
124 * buffered frames and afterwards also frames from the ieee80211_txq (obtained
125 * via the usual ieee80211_tx_dequeue).
126 */
127
128struct device;
129
130/**
131 * enum ieee80211_max_queues - maximum number of queues
132 *
133 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
134 * @IEEE80211_MAX_QUEUE_MAP: bitmap with maximum queues set
135 */
136enum ieee80211_max_queues {
137 IEEE80211_MAX_QUEUES = 16,
138 IEEE80211_MAX_QUEUE_MAP = BIT(IEEE80211_MAX_QUEUES) - 1,
139};
140
141#define IEEE80211_INVAL_HW_QUEUE 0xff
142
143/**
144 * enum ieee80211_ac_numbers - AC numbers as used in mac80211
145 * @IEEE80211_AC_VO: voice
146 * @IEEE80211_AC_VI: video
147 * @IEEE80211_AC_BE: best effort
148 * @IEEE80211_AC_BK: background
149 */
150enum ieee80211_ac_numbers {
151 IEEE80211_AC_VO = 0,
152 IEEE80211_AC_VI = 1,
153 IEEE80211_AC_BE = 2,
154 IEEE80211_AC_BK = 3,
155};
156
157/**
158 * struct ieee80211_tx_queue_params - transmit queue configuration
159 *
160 * The information provided in this structure is required for QoS
161 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
162 *
163 * @aifs: arbitration interframe space [0..255]
164 * @cw_min: minimum contention window [a value of the form
165 * 2^n-1 in the range 1..32767]
166 * @cw_max: maximum contention window [like @cw_min]
167 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
168 * @acm: is mandatory admission control required for the access category
169 * @uapsd: is U-APSD mode enabled for the queue
170 * @mu_edca: is the MU EDCA configured
171 * @mu_edca_param_rec: MU EDCA Parameter Record for HE
172 */
173struct ieee80211_tx_queue_params {
174 u16 txop;
175 u16 cw_min;
176 u16 cw_max;
177 u8 aifs;
178 bool acm;
179 bool uapsd;
180 bool mu_edca;
181 struct ieee80211_he_mu_edca_param_ac_rec mu_edca_param_rec;
182};
183
184struct ieee80211_low_level_stats {
185 unsigned int dot11ACKFailureCount;
186 unsigned int dot11RTSFailureCount;
187 unsigned int dot11FCSErrorCount;
188 unsigned int dot11RTSSuccessCount;
189};
190
191/**
192 * enum ieee80211_chanctx_change - change flag for channel context
193 * @IEEE80211_CHANCTX_CHANGE_WIDTH: The channel width changed
194 * @IEEE80211_CHANCTX_CHANGE_RX_CHAINS: The number of RX chains changed
195 * @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed
196 * @IEEE80211_CHANCTX_CHANGE_CHANNEL: switched to another operating channel,
197 * this is used only with channel switching with CSA
198 * @IEEE80211_CHANCTX_CHANGE_MIN_WIDTH: The min required channel width changed
199 */
200enum ieee80211_chanctx_change {
201 IEEE80211_CHANCTX_CHANGE_WIDTH = BIT(0),
202 IEEE80211_CHANCTX_CHANGE_RX_CHAINS = BIT(1),
203 IEEE80211_CHANCTX_CHANGE_RADAR = BIT(2),
204 IEEE80211_CHANCTX_CHANGE_CHANNEL = BIT(3),
205 IEEE80211_CHANCTX_CHANGE_MIN_WIDTH = BIT(4),
206};
207
208/**
209 * struct ieee80211_chanctx_conf - channel context that vifs may be tuned to
210 *
211 * This is the driver-visible part. The ieee80211_chanctx
212 * that contains it is visible in mac80211 only.
213 *
214 * @def: the channel definition
215 * @min_def: the minimum channel definition currently required.
216 * @rx_chains_static: The number of RX chains that must always be
217 * active on the channel to receive MIMO transmissions
218 * @rx_chains_dynamic: The number of RX chains that must be enabled
219 * after RTS/CTS handshake to receive SMPS MIMO transmissions;
220 * this will always be >= @rx_chains_static.
221 * @radar_enabled: whether radar detection is enabled on this channel.
222 * @drv_priv: data area for driver use, will always be aligned to
223 * sizeof(void *), size is determined in hw information.
224 */
225struct ieee80211_chanctx_conf {
226 struct cfg80211_chan_def def;
227 struct cfg80211_chan_def min_def;
228
229 u8 rx_chains_static, rx_chains_dynamic;
230
231 bool radar_enabled;
232
233 u8 drv_priv[0] __aligned(sizeof(void *));
234};
235
236/**
237 * enum ieee80211_chanctx_switch_mode - channel context switch mode
238 * @CHANCTX_SWMODE_REASSIGN_VIF: Both old and new contexts already
239 * exist (and will continue to exist), but the virtual interface
240 * needs to be switched from one to the other.
241 * @CHANCTX_SWMODE_SWAP_CONTEXTS: The old context exists but will stop
242 * to exist with this call, the new context doesn't exist but
243 * will be active after this call, the virtual interface switches
244 * from the old to the new (note that the driver may of course
245 * implement this as an on-the-fly chandef switch of the existing
246 * hardware context, but the mac80211 pointer for the old context
247 * will cease to exist and only the new one will later be used
248 * for changes/removal.)
249 */
250enum ieee80211_chanctx_switch_mode {
251 CHANCTX_SWMODE_REASSIGN_VIF,
252 CHANCTX_SWMODE_SWAP_CONTEXTS,
253};
254
255/**
256 * struct ieee80211_vif_chanctx_switch - vif chanctx switch information
257 *
258 * This is structure is used to pass information about a vif that
259 * needs to switch from one chanctx to another. The
260 * &ieee80211_chanctx_switch_mode defines how the switch should be
261 * done.
262 *
263 * @vif: the vif that should be switched from old_ctx to new_ctx
264 * @old_ctx: the old context to which the vif was assigned
265 * @new_ctx: the new context to which the vif must be assigned
266 */
267struct ieee80211_vif_chanctx_switch {
268 struct ieee80211_vif *vif;
269 struct ieee80211_chanctx_conf *old_ctx;
270 struct ieee80211_chanctx_conf *new_ctx;
271};
272
273/**
274 * enum ieee80211_bss_change - BSS change notification flags
275 *
276 * These flags are used with the bss_info_changed() callback
277 * to indicate which BSS parameter changed.
278 *
279 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
280 * also implies a change in the AID.
281 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
282 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
283 * @BSS_CHANGED_ERP_SLOT: slot timing changed
284 * @BSS_CHANGED_HT: 802.11n parameters changed
285 * @BSS_CHANGED_BASIC_RATES: Basic rateset changed
286 * @BSS_CHANGED_BEACON_INT: Beacon interval changed
287 * @BSS_CHANGED_BSSID: BSSID changed, for whatever
288 * reason (IBSS and managed mode)
289 * @BSS_CHANGED_BEACON: Beacon data changed, retrieve
290 * new beacon (beaconing modes)
291 * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
292 * enabled/disabled (beaconing modes)
293 * @BSS_CHANGED_CQM: Connection quality monitor config changed
294 * @BSS_CHANGED_IBSS: IBSS join status changed
295 * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed.
296 * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note
297 * that it is only ever disabled for station mode.
298 * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface.
299 * @BSS_CHANGED_SSID: SSID changed for this BSS (AP and IBSS mode)
300 * @BSS_CHANGED_AP_PROBE_RESP: Probe Response changed for this BSS (AP mode)
301 * @BSS_CHANGED_PS: PS changed for this BSS (STA mode)
302 * @BSS_CHANGED_TXPOWER: TX power setting changed for this interface
303 * @BSS_CHANGED_P2P_PS: P2P powersave settings (CTWindow, opportunistic PS)
304 * changed
305 * @BSS_CHANGED_BEACON_INFO: Data from the AP's beacon became available:
306 * currently dtim_period only is under consideration.
307 * @BSS_CHANGED_BANDWIDTH: The bandwidth used by this interface changed,
308 * note that this is only called when it changes after the channel
309 * context had been assigned.
310 * @BSS_CHANGED_OCB: OCB join status changed
311 * @BSS_CHANGED_MU_GROUPS: VHT MU-MIMO group id or user position changed
312 * @BSS_CHANGED_KEEP_ALIVE: keep alive options (idle period or protected
313 * keep alive) changed.
314 * @BSS_CHANGED_MCAST_RATE: Multicast Rate setting changed for this interface
315 * @BSS_CHANGED_FTM_RESPONDER: fime timing reasurement request responder
316 * functionality changed for this BSS (AP mode).
317 * @BSS_CHANGED_TWT: TWT status changed
318 * @BSS_CHANGED_HE_OBSS_PD: OBSS Packet Detection status changed.
319 *
320 */
321enum ieee80211_bss_change {
322 BSS_CHANGED_ASSOC = 1<<0,
323 BSS_CHANGED_ERP_CTS_PROT = 1<<1,
324 BSS_CHANGED_ERP_PREAMBLE = 1<<2,
325 BSS_CHANGED_ERP_SLOT = 1<<3,
326 BSS_CHANGED_HT = 1<<4,
327 BSS_CHANGED_BASIC_RATES = 1<<5,
328 BSS_CHANGED_BEACON_INT = 1<<6,
329 BSS_CHANGED_BSSID = 1<<7,
330 BSS_CHANGED_BEACON = 1<<8,
331 BSS_CHANGED_BEACON_ENABLED = 1<<9,
332 BSS_CHANGED_CQM = 1<<10,
333 BSS_CHANGED_IBSS = 1<<11,
334 BSS_CHANGED_ARP_FILTER = 1<<12,
335 BSS_CHANGED_QOS = 1<<13,
336 BSS_CHANGED_IDLE = 1<<14,
337 BSS_CHANGED_SSID = 1<<15,
338 BSS_CHANGED_AP_PROBE_RESP = 1<<16,
339 BSS_CHANGED_PS = 1<<17,
340 BSS_CHANGED_TXPOWER = 1<<18,
341 BSS_CHANGED_P2P_PS = 1<<19,
342 BSS_CHANGED_BEACON_INFO = 1<<20,
343 BSS_CHANGED_BANDWIDTH = 1<<21,
344 BSS_CHANGED_OCB = 1<<22,
345 BSS_CHANGED_MU_GROUPS = 1<<23,
346 BSS_CHANGED_KEEP_ALIVE = 1<<24,
347 BSS_CHANGED_MCAST_RATE = 1<<25,
348 BSS_CHANGED_FTM_RESPONDER = 1<<26,
349 BSS_CHANGED_TWT = 1<<27,
350 BSS_CHANGED_HE_OBSS_PD = 1<<28,
351
352 /* when adding here, make sure to change ieee80211_reconfig */
353};
354
355/*
356 * The maximum number of IPv4 addresses listed for ARP filtering. If the number
357 * of addresses for an interface increase beyond this value, hardware ARP
358 * filtering will be disabled.
359 */
360#define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4
361
362/**
363 * enum ieee80211_event_type - event to be notified to the low level driver
364 * @RSSI_EVENT: AP's rssi crossed the a threshold set by the driver.
365 * @MLME_EVENT: event related to MLME
366 * @BAR_RX_EVENT: a BAR was received
367 * @BA_FRAME_TIMEOUT: Frames were released from the reordering buffer because
368 * they timed out. This won't be called for each frame released, but only
369 * once each time the timeout triggers.
370 */
371enum ieee80211_event_type {
372 RSSI_EVENT,
373 MLME_EVENT,
374 BAR_RX_EVENT,
375 BA_FRAME_TIMEOUT,
376};
377
378/**
379 * enum ieee80211_rssi_event_data - relevant when event type is %RSSI_EVENT
380 * @RSSI_EVENT_HIGH: AP's rssi went below the threshold set by the driver.
381 * @RSSI_EVENT_LOW: AP's rssi went above the threshold set by the driver.
382 */
383enum ieee80211_rssi_event_data {
384 RSSI_EVENT_HIGH,
385 RSSI_EVENT_LOW,
386};
387
388/**
389 * struct ieee80211_rssi_event - data attached to an %RSSI_EVENT
390 * @data: See &enum ieee80211_rssi_event_data
391 */
392struct ieee80211_rssi_event {
393 enum ieee80211_rssi_event_data data;
394};
395
396/**
397 * enum ieee80211_mlme_event_data - relevant when event type is %MLME_EVENT
398 * @AUTH_EVENT: the MLME operation is authentication
399 * @ASSOC_EVENT: the MLME operation is association
400 * @DEAUTH_RX_EVENT: deauth received..
401 * @DEAUTH_TX_EVENT: deauth sent.
402 */
403enum ieee80211_mlme_event_data {
404 AUTH_EVENT,
405 ASSOC_EVENT,
406 DEAUTH_RX_EVENT,
407 DEAUTH_TX_EVENT,
408};
409
410/**
411 * enum ieee80211_mlme_event_status - relevant when event type is %MLME_EVENT
412 * @MLME_SUCCESS: the MLME operation completed successfully.
413 * @MLME_DENIED: the MLME operation was denied by the peer.
414 * @MLME_TIMEOUT: the MLME operation timed out.
415 */
416enum ieee80211_mlme_event_status {
417 MLME_SUCCESS,
418 MLME_DENIED,
419 MLME_TIMEOUT,
420};
421
422/**
423 * struct ieee80211_mlme_event - data attached to an %MLME_EVENT
424 * @data: See &enum ieee80211_mlme_event_data
425 * @status: See &enum ieee80211_mlme_event_status
426 * @reason: the reason code if applicable
427 */
428struct ieee80211_mlme_event {
429 enum ieee80211_mlme_event_data data;
430 enum ieee80211_mlme_event_status status;
431 u16 reason;
432};
433
434/**
435 * struct ieee80211_ba_event - data attached for BlockAck related events
436 * @sta: pointer to the &ieee80211_sta to which this event relates
437 * @tid: the tid
438 * @ssn: the starting sequence number (for %BAR_RX_EVENT)
439 */
440struct ieee80211_ba_event {
441 struct ieee80211_sta *sta;
442 u16 tid;
443 u16 ssn;
444};
445
446/**
447 * struct ieee80211_event - event to be sent to the driver
448 * @type: The event itself. See &enum ieee80211_event_type.
449 * @rssi: relevant if &type is %RSSI_EVENT
450 * @mlme: relevant if &type is %AUTH_EVENT
451 * @ba: relevant if &type is %BAR_RX_EVENT or %BA_FRAME_TIMEOUT
452 * @u:union holding the fields above
453 */
454struct ieee80211_event {
455 enum ieee80211_event_type type;
456 union {
457 struct ieee80211_rssi_event rssi;
458 struct ieee80211_mlme_event mlme;
459 struct ieee80211_ba_event ba;
460 } u;
461};
462
463/**
464 * struct ieee80211_mu_group_data - STA's VHT MU-MIMO group data
465 *
466 * This structure describes the group id data of VHT MU-MIMO
467 *
468 * @membership: 64 bits array - a bit is set if station is member of the group
469 * @position: 2 bits per group id indicating the position in the group
470 */
471struct ieee80211_mu_group_data {
472 u8 membership[WLAN_MEMBERSHIP_LEN];
473 u8 position[WLAN_USER_POSITION_LEN];
474};
475
476/**
477 * struct ieee80211_ftm_responder_params - FTM responder parameters
478 *
479 * @lci: LCI subelement content
480 * @civicloc: CIVIC location subelement content
481 * @lci_len: LCI data length
482 * @civicloc_len: Civic data length
483 */
484struct ieee80211_ftm_responder_params {
485 const u8 *lci;
486 const u8 *civicloc;
487 size_t lci_len;
488 size_t civicloc_len;
489};
490
491/**
492 * struct ieee80211_bss_conf - holds the BSS's changing parameters
493 *
494 * This structure keeps information about a BSS (and an association
495 * to that BSS) that can change during the lifetime of the BSS.
496 *
497 * @bss_color: 6-bit value to mark inter-BSS frame, if BSS supports HE
498 * @htc_trig_based_pkt_ext: default PE in 4us units, if BSS supports HE
499 * @multi_sta_back_32bit: supports BA bitmap of 32-bits in Multi-STA BACK
500 * @uora_exists: is the UORA element advertised by AP
501 * @ack_enabled: indicates support to receive a multi-TID that solicits either
502 * ACK, BACK or both
503 * @uora_ocw_range: UORA element's OCW Range field
504 * @frame_time_rts_th: HE duration RTS threshold, in units of 32us
505 * @he_support: does this BSS support HE
506 * @twt_requester: does this BSS support TWT requester (relevant for managed
507 * mode only, set if the AP advertises TWT responder role)
508 * @twt_responder: does this BSS support TWT requester (relevant for managed
509 * mode only, set if the AP advertises TWT responder role)
510 * @assoc: association status
511 * @ibss_joined: indicates whether this station is part of an IBSS
512 * or not
513 * @ibss_creator: indicates if a new IBSS network is being created
514 * @aid: association ID number, valid only when @assoc is true
515 * @use_cts_prot: use CTS protection
516 * @use_short_preamble: use 802.11b short preamble
517 * @use_short_slot: use short slot time (only relevant for ERP)
518 * @dtim_period: num of beacons before the next DTIM, for beaconing,
519 * valid in station mode only if after the driver was notified
520 * with the %BSS_CHANGED_BEACON_INFO flag, will be non-zero then.
521 * @sync_tsf: last beacon's/probe response's TSF timestamp (could be old
522 * as it may have been received during scanning long ago). If the
523 * HW flag %IEEE80211_HW_TIMING_BEACON_ONLY is set, then this can
524 * only come from a beacon, but might not become valid until after
525 * association when a beacon is received (which is notified with the
526 * %BSS_CHANGED_DTIM flag.). See also sync_dtim_count important notice.
527 * @sync_device_ts: the device timestamp corresponding to the sync_tsf,
528 * the driver/device can use this to calculate synchronisation
529 * (see @sync_tsf). See also sync_dtim_count important notice.
530 * @sync_dtim_count: Only valid when %IEEE80211_HW_TIMING_BEACON_ONLY
531 * is requested, see @sync_tsf/@sync_device_ts.
532 * IMPORTANT: These three sync_* parameters would possibly be out of sync
533 * by the time the driver will use them. The synchronized view is currently
534 * guaranteed only in certain callbacks.
535 * @beacon_int: beacon interval
536 * @assoc_capability: capabilities taken from assoc resp
537 * @basic_rates: bitmap of basic rates, each bit stands for an
538 * index into the rate table configured by the driver in
539 * the current band.
540 * @beacon_rate: associated AP's beacon TX rate
541 * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
542 * @bssid: The BSSID for this BSS
543 * @enable_beacon: whether beaconing should be enabled or not
544 * @chandef: Channel definition for this BSS -- the hardware might be
545 * configured a higher bandwidth than this BSS uses, for example.
546 * @mu_group: VHT MU-MIMO group membership data
547 * @ht_operation_mode: HT operation mode like in &struct ieee80211_ht_operation.
548 * This field is only valid when the channel is a wide HT/VHT channel.
549 * Note that with TDLS this can be the case (channel is HT, protection must
550 * be used from this field) even when the BSS association isn't using HT.
551 * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
552 * implies disabled. As with the cfg80211 callback, a change here should
553 * cause an event to be sent indicating where the current value is in
554 * relation to the newly configured threshold.
555 * @cqm_rssi_low: Connection quality monitor RSSI lower threshold, a zero value
556 * implies disabled. This is an alternative mechanism to the single
557 * threshold event and can't be enabled simultaneously with it.
558 * @cqm_rssi_high: Connection quality monitor RSSI upper threshold.
559 * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis
560 * @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The
561 * may filter ARP queries targeted for other addresses than listed here.
562 * The driver must allow ARP queries targeted for all address listed here
563 * to pass through. An empty list implies no ARP queries need to pass.
564 * @arp_addr_cnt: Number of addresses currently on the list. Note that this
565 * may be larger than %IEEE80211_BSS_ARP_ADDR_LIST_LEN (the arp_addr_list
566 * array size), it's up to the driver what to do in that case.
567 * @qos: This is a QoS-enabled BSS.
568 * @idle: This interface is idle. There's also a global idle flag in the
569 * hardware config which may be more appropriate depending on what
570 * your driver/device needs to do.
571 * @ps: power-save mode (STA only). This flag is NOT affected by
572 * offchannel/dynamic_ps operations.
573 * @ssid: The SSID of the current vif. Valid in AP and IBSS mode.
574 * @ssid_len: Length of SSID given in @ssid.
575 * @hidden_ssid: The SSID of the current vif is hidden. Only valid in AP-mode.
576 * @txpower: TX power in dBm
577 * @txpower_type: TX power adjustment used to control per packet Transmit
578 * Power Control (TPC) in lower driver for the current vif. In particular
579 * TPC is enabled if value passed in %txpower_type is
580 * NL80211_TX_POWER_LIMITED (allow using less than specified from
581 * userspace), whereas TPC is disabled if %txpower_type is set to
582 * NL80211_TX_POWER_FIXED (use value configured from userspace)
583 * @p2p_noa_attr: P2P NoA attribute for P2P powersave
584 * @allow_p2p_go_ps: indication for AP or P2P GO interface, whether it's allowed
585 * to use P2P PS mechanism or not. AP/P2P GO is not allowed to use P2P PS
586 * if it has associated clients without P2P PS support.
587 * @max_idle_period: the time period during which the station can refrain from
588 * transmitting frames to its associated AP without being disassociated.
589 * In units of 1000 TUs. Zero value indicates that the AP did not include
590 * a (valid) BSS Max Idle Period Element.
591 * @protected_keep_alive: if set, indicates that the station should send an RSN
592 * protected frame to the AP to reset the idle timer at the AP for the
593 * station.
594 * @ftm_responder: whether to enable or disable fine timing measurement FTM
595 * responder functionality.
596 * @ftmr_params: configurable lci/civic parameter when enabling FTM responder.
597 * @nontransmitted: this BSS is a nontransmitted BSS profile
598 * @transmitter_bssid: the address of transmitter AP
599 * @bssid_index: index inside the multiple BSSID set
600 * @bssid_indicator: 2^bssid_indicator is the maximum number of APs in set
601 * @ema_ap: AP supports enhancements of discovery and advertisement of
602 * nontransmitted BSSIDs
603 * @profile_periodicity: the least number of beacon frames need to be received
604 * in order to discover all the nontransmitted BSSIDs in the set.
605 * @he_operation: HE operation information of the AP we are connected to
606 * @he_obss_pd: OBSS Packet Detection parameters.
607 */
608struct ieee80211_bss_conf {
609 const u8 *bssid;
610 u8 bss_color;
611 u8 htc_trig_based_pkt_ext;
612 bool multi_sta_back_32bit;
613 bool uora_exists;
614 bool ack_enabled;
615 u8 uora_ocw_range;
616 u16 frame_time_rts_th;
617 bool he_support;
618 bool twt_requester;
619 bool twt_responder;
620 /* association related data */
621 bool assoc, ibss_joined;
622 bool ibss_creator;
623 u16 aid;
624 /* erp related data */
625 bool use_cts_prot;
626 bool use_short_preamble;
627 bool use_short_slot;
628 bool enable_beacon;
629 u8 dtim_period;
630 u16 beacon_int;
631 u16 assoc_capability;
632 u64 sync_tsf;
633 u32 sync_device_ts;
634 u8 sync_dtim_count;
635 u32 basic_rates;
636 struct ieee80211_rate *beacon_rate;
637 int mcast_rate[NUM_NL80211_BANDS];
638 u16 ht_operation_mode;
639 s32 cqm_rssi_thold;
640 u32 cqm_rssi_hyst;
641 s32 cqm_rssi_low;
642 s32 cqm_rssi_high;
643 struct cfg80211_chan_def chandef;
644 struct ieee80211_mu_group_data mu_group;
645 __be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN];
646 int arp_addr_cnt;
647 bool qos;
648 bool idle;
649 bool ps;
650 u8 ssid[IEEE80211_MAX_SSID_LEN];
651 size_t ssid_len;
652 bool hidden_ssid;
653 int txpower;
654 enum nl80211_tx_power_setting txpower_type;
655 struct ieee80211_p2p_noa_attr p2p_noa_attr;
656 bool allow_p2p_go_ps;
657 u16 max_idle_period;
658 bool protected_keep_alive;
659 bool ftm_responder;
660 struct ieee80211_ftm_responder_params *ftmr_params;
661 /* Multiple BSSID data */
662 bool nontransmitted;
663 u8 transmitter_bssid[ETH_ALEN];
664 u8 bssid_index;
665 u8 bssid_indicator;
666 bool ema_ap;
667 u8 profile_periodicity;
668 struct ieee80211_he_operation he_operation;
669 struct ieee80211_he_obss_pd he_obss_pd;
670};
671
672/**
673 * enum mac80211_tx_info_flags - flags to describe transmission information/status
674 *
675 * These flags are used with the @flags member of &ieee80211_tx_info.
676 *
677 * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame.
678 * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
679 * number to this frame, taking care of not overwriting the fragment
680 * number and increasing the sequence number only when the
681 * IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
682 * assign sequence numbers to QoS-data frames but cannot do so correctly
683 * for non-QoS-data and management frames because beacons need them from
684 * that counter as well and mac80211 cannot guarantee proper sequencing.
685 * If this flag is set, the driver should instruct the hardware to
686 * assign a sequence number to the frame or assign one itself. Cf. IEEE
687 * 802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
688 * beacons and always be clear for frames without a sequence number field.
689 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
690 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
691 * station
692 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
693 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
694 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
695 * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
696 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
697 * because the destination STA was in powersave mode. Note that to
698 * avoid race conditions, the filter must be set by the hardware or
699 * firmware upon receiving a frame that indicates that the station
700 * went to sleep (must be done on device to filter frames already on
701 * the queue) and may only be unset after mac80211 gives the OK for
702 * that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above),
703 * since only then is it guaranteed that no more frames are in the
704 * hardware queue.
705 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
706 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
707 * is for the whole aggregation.
708 * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
709 * so consider using block ack request (BAR).
710 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
711 * set by rate control algorithms to indicate probe rate, will
712 * be cleared for fragmented frames (except on the last fragment)
713 * @IEEE80211_TX_INTFL_OFFCHAN_TX_OK: Internal to mac80211. Used to indicate
714 * that a frame can be transmitted while the queues are stopped for
715 * off-channel operation.
716 * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211,
717 * used to indicate that a pending frame requires TX processing before
718 * it can be sent out.
719 * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211,
720 * used to indicate that a frame was already retried due to PS
721 * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
722 * used to indicate frame should not be encrypted
723 * @IEEE80211_TX_CTL_NO_PS_BUFFER: This frame is a response to a poll
724 * frame (PS-Poll or uAPSD) or a non-bufferable MMPDU and must
725 * be sent although the station is in powersave mode.
726 * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the
727 * transmit function after the current frame, this can be used
728 * by drivers to kick the DMA queue only if unset or when the
729 * queue gets full.
730 * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted
731 * after TX status because the destination was asleep, it must not
732 * be modified again (no seqno assignment, crypto, etc.)
733 * @IEEE80211_TX_INTFL_MLME_CONN_TX: This frame was transmitted by the MLME
734 * code for connection establishment, this indicates that its status
735 * should kick the MLME state machine.
736 * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211
737 * MLME command (internal to mac80211 to figure out whether to send TX
738 * status to user space)
739 * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame
740 * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this
741 * frame and selects the maximum number of streams that it can use.
742 * @IEEE80211_TX_CTL_TX_OFFCHAN: Marks this packet to be transmitted on
743 * the off-channel channel when a remain-on-channel offload is done
744 * in hardware -- normal packets still flow and are expected to be
745 * handled properly by the device.
746 * @IEEE80211_TX_INTFL_TKIP_MIC_FAILURE: Marks this packet to be used for TKIP
747 * testing. It will be sent out with incorrect Michael MIC key to allow
748 * TKIP countermeasures to be tested.
749 * @IEEE80211_TX_CTL_NO_CCK_RATE: This frame will be sent at non CCK rate.
750 * This flag is actually used for management frame especially for P2P
751 * frames not being sent at CCK rate in 2GHz band.
752 * @IEEE80211_TX_STATUS_EOSP: This packet marks the end of service period,
753 * when its status is reported the service period ends. For frames in
754 * an SP that mac80211 transmits, it is already set; for driver frames
755 * the driver may set this flag. It is also used to do the same for
756 * PS-Poll responses.
757 * @IEEE80211_TX_CTL_USE_MINRATE: This frame will be sent at lowest rate.
758 * This flag is used to send nullfunc frame at minimum rate when
759 * the nullfunc is used for connection monitoring purpose.
760 * @IEEE80211_TX_CTL_DONTFRAG: Don't fragment this packet even if it
761 * would be fragmented by size (this is optional, only used for
762 * monitor injection).
763 * @IEEE80211_TX_STAT_NOACK_TRANSMITTED: A frame that was marked with
764 * IEEE80211_TX_CTL_NO_ACK has been successfully transmitted without
765 * any errors (like issues specific to the driver/HW).
766 * This flag must not be set for frames that don't request no-ack
767 * behaviour with IEEE80211_TX_CTL_NO_ACK.
768 *
769 * Note: If you have to add new flags to the enumeration, then don't
770 * forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary.
771 */
772enum mac80211_tx_info_flags {
773 IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
774 IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(1),
775 IEEE80211_TX_CTL_NO_ACK = BIT(2),
776 IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(3),
777 IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(4),
778 IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(5),
779 IEEE80211_TX_CTL_AMPDU = BIT(6),
780 IEEE80211_TX_CTL_INJECTED = BIT(7),
781 IEEE80211_TX_STAT_TX_FILTERED = BIT(8),
782 IEEE80211_TX_STAT_ACK = BIT(9),
783 IEEE80211_TX_STAT_AMPDU = BIT(10),
784 IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11),
785 IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12),
786 IEEE80211_TX_INTFL_OFFCHAN_TX_OK = BIT(13),
787 IEEE80211_TX_INTFL_NEED_TXPROCESSING = BIT(14),
788 IEEE80211_TX_INTFL_RETRIED = BIT(15),
789 IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16),
790 IEEE80211_TX_CTL_NO_PS_BUFFER = BIT(17),
791 IEEE80211_TX_CTL_MORE_FRAMES = BIT(18),
792 IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19),
793 IEEE80211_TX_INTFL_MLME_CONN_TX = BIT(20),
794 IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21),
795 IEEE80211_TX_CTL_LDPC = BIT(22),
796 IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24),
797 IEEE80211_TX_CTL_TX_OFFCHAN = BIT(25),
798 IEEE80211_TX_INTFL_TKIP_MIC_FAILURE = BIT(26),
799 IEEE80211_TX_CTL_NO_CCK_RATE = BIT(27),
800 IEEE80211_TX_STATUS_EOSP = BIT(28),
801 IEEE80211_TX_CTL_USE_MINRATE = BIT(29),
802 IEEE80211_TX_CTL_DONTFRAG = BIT(30),
803 IEEE80211_TX_STAT_NOACK_TRANSMITTED = BIT(31),
804};
805
806#define IEEE80211_TX_CTL_STBC_SHIFT 23
807
808/**
809 * enum mac80211_tx_control_flags - flags to describe transmit control
810 *
811 * @IEEE80211_TX_CTRL_PORT_CTRL_PROTO: this frame is a port control
812 * protocol frame (e.g. EAP)
813 * @IEEE80211_TX_CTRL_PS_RESPONSE: This frame is a response to a poll
814 * frame (PS-Poll or uAPSD).
815 * @IEEE80211_TX_CTRL_RATE_INJECT: This frame is injected with rate information
816 * @IEEE80211_TX_CTRL_AMSDU: This frame is an A-MSDU frame
817 * @IEEE80211_TX_CTRL_FAST_XMIT: This frame is going through the fast_xmit path
818 * @IEEE80211_TX_CTRL_SKIP_MPATH_LOOKUP: This frame skips mesh path lookup
819 *
820 * These flags are used in tx_info->control.flags.
821 */
822enum mac80211_tx_control_flags {
823 IEEE80211_TX_CTRL_PORT_CTRL_PROTO = BIT(0),
824 IEEE80211_TX_CTRL_PS_RESPONSE = BIT(1),
825 IEEE80211_TX_CTRL_RATE_INJECT = BIT(2),
826 IEEE80211_TX_CTRL_AMSDU = BIT(3),
827 IEEE80211_TX_CTRL_FAST_XMIT = BIT(4),
828 IEEE80211_TX_CTRL_SKIP_MPATH_LOOKUP = BIT(5),
829};
830
831/*
832 * This definition is used as a mask to clear all temporary flags, which are
833 * set by the tx handlers for each transmission attempt by the mac80211 stack.
834 */
835#define IEEE80211_TX_TEMPORARY_FLAGS (IEEE80211_TX_CTL_NO_ACK | \
836 IEEE80211_TX_CTL_CLEAR_PS_FILT | IEEE80211_TX_CTL_FIRST_FRAGMENT | \
837 IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU | \
838 IEEE80211_TX_STAT_TX_FILTERED | IEEE80211_TX_STAT_ACK | \
839 IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK | \
840 IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_NO_PS_BUFFER | \
841 IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC | \
842 IEEE80211_TX_CTL_STBC | IEEE80211_TX_STATUS_EOSP)
843
844/**
845 * enum mac80211_rate_control_flags - per-rate flags set by the
846 * Rate Control algorithm.
847 *
848 * These flags are set by the Rate control algorithm for each rate during tx,
849 * in the @flags member of struct ieee80211_tx_rate.
850 *
851 * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
852 * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
853 * This is set if the current BSS requires ERP protection.
854 * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
855 * @IEEE80211_TX_RC_MCS: HT rate.
856 * @IEEE80211_TX_RC_VHT_MCS: VHT MCS rate, in this case the idx field is split
857 * into a higher 4 bits (Nss) and lower 4 bits (MCS number)
858 * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
859 * Greenfield mode.
860 * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
861 * @IEEE80211_TX_RC_80_MHZ_WIDTH: Indicates 80 MHz transmission
862 * @IEEE80211_TX_RC_160_MHZ_WIDTH: Indicates 160 MHz transmission
863 * (80+80 isn't supported yet)
864 * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
865 * adjacent 20 MHz channels, if the current channel type is
866 * NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
867 * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
868 */
869enum mac80211_rate_control_flags {
870 IEEE80211_TX_RC_USE_RTS_CTS = BIT(0),
871 IEEE80211_TX_RC_USE_CTS_PROTECT = BIT(1),
872 IEEE80211_TX_RC_USE_SHORT_PREAMBLE = BIT(2),
873
874 /* rate index is an HT/VHT MCS instead of an index */
875 IEEE80211_TX_RC_MCS = BIT(3),
876 IEEE80211_TX_RC_GREEN_FIELD = BIT(4),
877 IEEE80211_TX_RC_40_MHZ_WIDTH = BIT(5),
878 IEEE80211_TX_RC_DUP_DATA = BIT(6),
879 IEEE80211_TX_RC_SHORT_GI = BIT(7),
880 IEEE80211_TX_RC_VHT_MCS = BIT(8),
881 IEEE80211_TX_RC_80_MHZ_WIDTH = BIT(9),
882 IEEE80211_TX_RC_160_MHZ_WIDTH = BIT(10),
883};
884
885
886/* there are 40 bytes if you don't need the rateset to be kept */
887#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
888
889/* if you do need the rateset, then you have less space */
890#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
891
892/* maximum number of rate stages */
893#define IEEE80211_TX_MAX_RATES 4
894
895/* maximum number of rate table entries */
896#define IEEE80211_TX_RATE_TABLE_SIZE 4
897
898/**
899 * struct ieee80211_tx_rate - rate selection/status
900 *
901 * @idx: rate index to attempt to send with
902 * @flags: rate control flags (&enum mac80211_rate_control_flags)
903 * @count: number of tries in this rate before going to the next rate
904 *
905 * A value of -1 for @idx indicates an invalid rate and, if used
906 * in an array of retry rates, that no more rates should be tried.
907 *
908 * When used for transmit status reporting, the driver should
909 * always report the rate along with the flags it used.
910 *
911 * &struct ieee80211_tx_info contains an array of these structs
912 * in the control information, and it will be filled by the rate
913 * control algorithm according to what should be sent. For example,
914 * if this array contains, in the format { <idx>, <count> } the
915 * information::
916 *
917 * { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 }
918 *
919 * then this means that the frame should be transmitted
920 * up to twice at rate 3, up to twice at rate 2, and up to four
921 * times at rate 1 if it doesn't get acknowledged. Say it gets
922 * acknowledged by the peer after the fifth attempt, the status
923 * information should then contain::
924 *
925 * { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ...
926 *
927 * since it was transmitted twice at rate 3, twice at rate 2
928 * and once at rate 1 after which we received an acknowledgement.
929 */
930struct ieee80211_tx_rate {
931 s8 idx;
932 u16 count:5,
933 flags:11;
934} __packed;
935
936#define IEEE80211_MAX_TX_RETRY 31
937
938static inline void ieee80211_rate_set_vht(struct ieee80211_tx_rate *rate,
939 u8 mcs, u8 nss)
940{
941 WARN_ON(mcs & ~0xF);
942 WARN_ON((nss - 1) & ~0x7);
943 rate->idx = ((nss - 1) << 4) | mcs;
944}
945
946static inline u8
947ieee80211_rate_get_vht_mcs(const struct ieee80211_tx_rate *rate)
948{
949 return rate->idx & 0xF;
950}
951
952static inline u8
953ieee80211_rate_get_vht_nss(const struct ieee80211_tx_rate *rate)
954{
955 return (rate->idx >> 4) + 1;
956}
957
958/**
959 * struct ieee80211_tx_info - skb transmit information
960 *
961 * This structure is placed in skb->cb for three uses:
962 * (1) mac80211 TX control - mac80211 tells the driver what to do
963 * (2) driver internal use (if applicable)
964 * (3) TX status information - driver tells mac80211 what happened
965 *
966 * @flags: transmit info flags, defined above
967 * @band: the band to transmit on (use for checking for races)
968 * @hw_queue: HW queue to put the frame on, skb_get_queue_mapping() gives the AC
969 * @ack_frame_id: internal frame ID for TX status, used internally
970 * @control: union part for control data
971 * @control.rates: TX rates array to try
972 * @control.rts_cts_rate_idx: rate for RTS or CTS
973 * @control.use_rts: use RTS
974 * @control.use_cts_prot: use RTS/CTS
975 * @control.short_preamble: use short preamble (CCK only)
976 * @control.skip_table: skip externally configured rate table
977 * @control.jiffies: timestamp for expiry on powersave clients
978 * @control.vif: virtual interface (may be NULL)
979 * @control.hw_key: key to encrypt with (may be NULL)
980 * @control.flags: control flags, see &enum mac80211_tx_control_flags
981 * @control.enqueue_time: enqueue time (for iTXQs)
982 * @driver_rates: alias to @control.rates to reserve space
983 * @pad: padding
984 * @rate_driver_data: driver use area if driver needs @control.rates
985 * @status: union part for status data
986 * @status.rates: attempted rates
987 * @status.ack_signal: ACK signal
988 * @status.ampdu_ack_len: AMPDU ack length
989 * @status.ampdu_len: AMPDU length
990 * @status.antenna: (legacy, kept only for iwlegacy)
991 * @status.tx_time: airtime consumed for transmission
992 * @status.is_valid_ack_signal: ACK signal is valid
993 * @status.status_driver_data: driver use area
994 * @ack: union part for pure ACK data
995 * @ack.cookie: cookie for the ACK
996 * @driver_data: array of driver_data pointers
997 * @ampdu_ack_len: number of acked aggregated frames.
998 * relevant only if IEEE80211_TX_STAT_AMPDU was set.
999 * @ampdu_len: number of aggregated frames.
1000 * relevant only if IEEE80211_TX_STAT_AMPDU was set.
1001 * @ack_signal: signal strength of the ACK frame
1002 */
1003struct ieee80211_tx_info {
1004 /* common information */
1005 u32 flags;
1006 u8 band;
1007
1008 u8 hw_queue;
1009
1010 u16 ack_frame_id;
1011
1012 union {
1013 struct {
1014 union {
1015 /* rate control */
1016 struct {
1017 struct ieee80211_tx_rate rates[
1018 IEEE80211_TX_MAX_RATES];
1019 s8 rts_cts_rate_idx;
1020 u8 use_rts:1;
1021 u8 use_cts_prot:1;
1022 u8 short_preamble:1;
1023 u8 skip_table:1;
1024 /* 2 bytes free */
1025 };
1026 /* only needed before rate control */
1027 unsigned long jiffies;
1028 };
1029 /* NB: vif can be NULL for injected frames */
1030 struct ieee80211_vif *vif;
1031 struct ieee80211_key_conf *hw_key;
1032 u32 flags;
1033 codel_time_t enqueue_time;
1034 } control;
1035 struct {
1036 u64 cookie;
1037 } ack;
1038 struct {
1039 struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
1040 s32 ack_signal;
1041 u8 ampdu_ack_len;
1042 u8 ampdu_len;
1043 u8 antenna;
1044 u16 tx_time;
1045 bool is_valid_ack_signal;
1046 void *status_driver_data[19 / sizeof(void *)];
1047 } status;
1048 struct {
1049 struct ieee80211_tx_rate driver_rates[
1050 IEEE80211_TX_MAX_RATES];
1051 u8 pad[4];
1052
1053 void *rate_driver_data[
1054 IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
1055 };
1056 void *driver_data[
1057 IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
1058 };
1059};
1060
1061/**
1062 * struct ieee80211_tx_status - extended tx staus info for rate control
1063 *
1064 * @sta: Station that the packet was transmitted for
1065 * @info: Basic tx status information
1066 * @skb: Packet skb (can be NULL if not provided by the driver)
1067 * @rate: The TX rate that was used when sending the packet
1068 */
1069struct ieee80211_tx_status {
1070 struct ieee80211_sta *sta;
1071 struct ieee80211_tx_info *info;
1072 struct sk_buff *skb;
1073 struct rate_info *rate;
1074};
1075
1076/**
1077 * struct ieee80211_scan_ies - descriptors for different blocks of IEs
1078 *
1079 * This structure is used to point to different blocks of IEs in HW scan
1080 * and scheduled scan. These blocks contain the IEs passed by userspace
1081 * and the ones generated by mac80211.
1082 *
1083 * @ies: pointers to band specific IEs.
1084 * @len: lengths of band_specific IEs.
1085 * @common_ies: IEs for all bands (especially vendor specific ones)
1086 * @common_ie_len: length of the common_ies
1087 */
1088struct ieee80211_scan_ies {
1089 const u8 *ies[NUM_NL80211_BANDS];
1090 size_t len[NUM_NL80211_BANDS];
1091 const u8 *common_ies;
1092 size_t common_ie_len;
1093};
1094
1095
1096static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
1097{
1098 return (struct ieee80211_tx_info *)skb->cb;
1099}
1100
1101static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb)
1102{
1103 return (struct ieee80211_rx_status *)skb->cb;
1104}
1105
1106/**
1107 * ieee80211_tx_info_clear_status - clear TX status
1108 *
1109 * @info: The &struct ieee80211_tx_info to be cleared.
1110 *
1111 * When the driver passes an skb back to mac80211, it must report
1112 * a number of things in TX status. This function clears everything
1113 * in the TX status but the rate control information (it does clear
1114 * the count since you need to fill that in anyway).
1115 *
1116 * NOTE: You can only use this function if you do NOT use
1117 * info->driver_data! Use info->rate_driver_data
1118 * instead if you need only the less space that allows.
1119 */
1120static inline void
1121ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
1122{
1123 int i;
1124
1125 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
1126 offsetof(struct ieee80211_tx_info, control.rates));
1127 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
1128 offsetof(struct ieee80211_tx_info, driver_rates));
1129 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
1130 /* clear the rate counts */
1131 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
1132 info->status.rates[i].count = 0;
1133
1134 BUILD_BUG_ON(
1135 offsetof(struct ieee80211_tx_info, status.ack_signal) != 20);
1136 memset(&info->status.ampdu_ack_len, 0,
1137 sizeof(struct ieee80211_tx_info) -
1138 offsetof(struct ieee80211_tx_info, status.ampdu_ack_len));
1139}
1140
1141
1142/**
1143 * enum mac80211_rx_flags - receive flags
1144 *
1145 * These flags are used with the @flag member of &struct ieee80211_rx_status.
1146 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
1147 * Use together with %RX_FLAG_MMIC_STRIPPED.
1148 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
1149 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
1150 * verification has been done by the hardware.
1151 * @RX_FLAG_IV_STRIPPED: The IV and ICV are stripped from this frame.
1152 * If this flag is set, the stack cannot do any replay detection
1153 * hence the driver or hardware will have to do that.
1154 * @RX_FLAG_PN_VALIDATED: Currently only valid for CCMP/GCMP frames, this
1155 * flag indicates that the PN was verified for replay protection.
1156 * Note that this flag is also currently only supported when a frame
1157 * is also decrypted (ie. @RX_FLAG_DECRYPTED must be set)
1158 * @RX_FLAG_DUP_VALIDATED: The driver should set this flag if it did
1159 * de-duplication by itself.
1160 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
1161 * the frame.
1162 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
1163 * the frame.
1164 * @RX_FLAG_MACTIME_START: The timestamp passed in the RX status (@mactime
1165 * field) is valid and contains the time the first symbol of the MPDU
1166 * was received. This is useful in monitor mode and for proper IBSS
1167 * merging.
1168 * @RX_FLAG_MACTIME_END: The timestamp passed in the RX status (@mactime
1169 * field) is valid and contains the time the last symbol of the MPDU
1170 * (including FCS) was received.
1171 * @RX_FLAG_MACTIME_PLCP_START: The timestamp passed in the RX status (@mactime
1172 * field) is valid and contains the time the SYNC preamble was received.
1173 * @RX_FLAG_NO_SIGNAL_VAL: The signal strength value is not present.
1174 * Valid only for data frames (mainly A-MPDU)
1175 * @RX_FLAG_AMPDU_DETAILS: A-MPDU details are known, in particular the reference
1176 * number (@ampdu_reference) must be populated and be a distinct number for
1177 * each A-MPDU
1178 * @RX_FLAG_AMPDU_LAST_KNOWN: last subframe is known, should be set on all
1179 * subframes of a single A-MPDU
1180 * @RX_FLAG_AMPDU_IS_LAST: this subframe is the last subframe of the A-MPDU
1181 * @RX_FLAG_AMPDU_DELIM_CRC_ERROR: A delimiter CRC error has been detected
1182 * on this subframe
1183 * @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC
1184 * is stored in the @ampdu_delimiter_crc field)
1185 * @RX_FLAG_MIC_STRIPPED: The mic was stripped of this packet. Decryption was
1186 * done by the hardware
1187 * @RX_FLAG_ONLY_MONITOR: Report frame only to monitor interfaces without
1188 * processing it in any regular way.
1189 * This is useful if drivers offload some frames but still want to report
1190 * them for sniffing purposes.
1191 * @RX_FLAG_SKIP_MONITOR: Process and report frame to all interfaces except
1192 * monitor interfaces.
1193 * This is useful if drivers offload some frames but still want to report
1194 * them for sniffing purposes.
1195 * @RX_FLAG_AMSDU_MORE: Some drivers may prefer to report separate A-MSDU
1196 * subframes instead of a one huge frame for performance reasons.
1197 * All, but the last MSDU from an A-MSDU should have this flag set. E.g.
1198 * if an A-MSDU has 3 frames, the first 2 must have the flag set, while
1199 * the 3rd (last) one must not have this flag set. The flag is used to
1200 * deal with retransmission/duplication recovery properly since A-MSDU
1201 * subframes share the same sequence number. Reported subframes can be
1202 * either regular MSDU or singly A-MSDUs. Subframes must not be
1203 * interleaved with other frames.
1204 * @RX_FLAG_RADIOTAP_VENDOR_DATA: This frame contains vendor-specific
1205 * radiotap data in the skb->data (before the frame) as described by
1206 * the &struct ieee80211_vendor_radiotap.
1207 * @RX_FLAG_ALLOW_SAME_PN: Allow the same PN as same packet before.
1208 * This is used for AMSDU subframes which can have the same PN as
1209 * the first subframe.
1210 * @RX_FLAG_ICV_STRIPPED: The ICV is stripped from this frame. CRC checking must
1211 * be done in the hardware.
1212 * @RX_FLAG_AMPDU_EOF_BIT: Value of the EOF bit in the A-MPDU delimiter for this
1213 * frame
1214 * @RX_FLAG_AMPDU_EOF_BIT_KNOWN: The EOF value is known
1215 * @RX_FLAG_RADIOTAP_HE: HE radiotap data is present
1216 * (&struct ieee80211_radiotap_he, mac80211 will fill in
1217 *
1218 * - DATA3_DATA_MCS
1219 * - DATA3_DATA_DCM
1220 * - DATA3_CODING
1221 * - DATA5_GI
1222 * - DATA5_DATA_BW_RU_ALLOC
1223 * - DATA6_NSTS
1224 * - DATA3_STBC
1225 *
1226 * from the RX info data, so leave those zeroed when building this data)
1227 * @RX_FLAG_RADIOTAP_HE_MU: HE MU radiotap data is present
1228 * (&struct ieee80211_radiotap_he_mu)
1229 * @RX_FLAG_RADIOTAP_LSIG: L-SIG radiotap data is present
1230 * @RX_FLAG_NO_PSDU: use the frame only for radiotap reporting, with
1231 * the "0-length PSDU" field included there. The value for it is
1232 * in &struct ieee80211_rx_status. Note that if this value isn't
1233 * known the frame shouldn't be reported.
1234 */
1235enum mac80211_rx_flags {
1236 RX_FLAG_MMIC_ERROR = BIT(0),
1237 RX_FLAG_DECRYPTED = BIT(1),
1238 RX_FLAG_MACTIME_PLCP_START = BIT(2),
1239 RX_FLAG_MMIC_STRIPPED = BIT(3),
1240 RX_FLAG_IV_STRIPPED = BIT(4),
1241 RX_FLAG_FAILED_FCS_CRC = BIT(5),
1242 RX_FLAG_FAILED_PLCP_CRC = BIT(6),
1243 RX_FLAG_MACTIME_START = BIT(7),
1244 RX_FLAG_NO_SIGNAL_VAL = BIT(8),
1245 RX_FLAG_AMPDU_DETAILS = BIT(9),
1246 RX_FLAG_PN_VALIDATED = BIT(10),
1247 RX_FLAG_DUP_VALIDATED = BIT(11),
1248 RX_FLAG_AMPDU_LAST_KNOWN = BIT(12),
1249 RX_FLAG_AMPDU_IS_LAST = BIT(13),
1250 RX_FLAG_AMPDU_DELIM_CRC_ERROR = BIT(14),
1251 RX_FLAG_AMPDU_DELIM_CRC_KNOWN = BIT(15),
1252 RX_FLAG_MACTIME_END = BIT(16),
1253 RX_FLAG_ONLY_MONITOR = BIT(17),
1254 RX_FLAG_SKIP_MONITOR = BIT(18),
1255 RX_FLAG_AMSDU_MORE = BIT(19),
1256 RX_FLAG_RADIOTAP_VENDOR_DATA = BIT(20),
1257 RX_FLAG_MIC_STRIPPED = BIT(21),
1258 RX_FLAG_ALLOW_SAME_PN = BIT(22),
1259 RX_FLAG_ICV_STRIPPED = BIT(23),
1260 RX_FLAG_AMPDU_EOF_BIT = BIT(24),
1261 RX_FLAG_AMPDU_EOF_BIT_KNOWN = BIT(25),
1262 RX_FLAG_RADIOTAP_HE = BIT(26),
1263 RX_FLAG_RADIOTAP_HE_MU = BIT(27),
1264 RX_FLAG_RADIOTAP_LSIG = BIT(28),
1265 RX_FLAG_NO_PSDU = BIT(29),
1266};
1267
1268/**
1269 * enum mac80211_rx_encoding_flags - MCS & bandwidth flags
1270 *
1271 * @RX_ENC_FLAG_SHORTPRE: Short preamble was used for this frame
1272 * @RX_ENC_FLAG_SHORT_GI: Short guard interval was used
1273 * @RX_ENC_FLAG_HT_GF: This frame was received in a HT-greenfield transmission,
1274 * if the driver fills this value it should add
1275 * %IEEE80211_RADIOTAP_MCS_HAVE_FMT
1276 * to @hw.radiotap_mcs_details to advertise that fact.
1277 * @RX_ENC_FLAG_LDPC: LDPC was used
1278 * @RX_ENC_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
1279 * @RX_ENC_FLAG_BF: packet was beamformed
1280 */
1281enum mac80211_rx_encoding_flags {
1282 RX_ENC_FLAG_SHORTPRE = BIT(0),
1283 RX_ENC_FLAG_SHORT_GI = BIT(2),
1284 RX_ENC_FLAG_HT_GF = BIT(3),
1285 RX_ENC_FLAG_STBC_MASK = BIT(4) | BIT(5),
1286 RX_ENC_FLAG_LDPC = BIT(6),
1287 RX_ENC_FLAG_BF = BIT(7),
1288};
1289
1290#define RX_ENC_FLAG_STBC_SHIFT 4
1291
1292enum mac80211_rx_encoding {
1293 RX_ENC_LEGACY = 0,
1294 RX_ENC_HT,
1295 RX_ENC_VHT,
1296 RX_ENC_HE,
1297};
1298
1299/**
1300 * struct ieee80211_rx_status - receive status
1301 *
1302 * The low-level driver should provide this information (the subset
1303 * supported by hardware) to the 802.11 code with each received
1304 * frame, in the skb's control buffer (cb).
1305 *
1306 * @mactime: value in microseconds of the 64-bit Time Synchronization Function
1307 * (TSF) timer when the first data symbol (MPDU) arrived at the hardware.
1308 * @boottime_ns: CLOCK_BOOTTIME timestamp the frame was received at, this is
1309 * needed only for beacons and probe responses that update the scan cache.
1310 * @device_timestamp: arbitrary timestamp for the device, mac80211 doesn't use
1311 * it but can store it and pass it back to the driver for synchronisation
1312 * @band: the active band when this frame was received
1313 * @freq: frequency the radio was tuned to when receiving this frame, in MHz
1314 * This field must be set for management frames, but isn't strictly needed
1315 * for data (other) frames - for those it only affects radiotap reporting.
1316 * @signal: signal strength when receiving this frame, either in dBm, in dB or
1317 * unspecified depending on the hardware capabilities flags
1318 * @IEEE80211_HW_SIGNAL_*
1319 * @chains: bitmask of receive chains for which separate signal strength
1320 * values were filled.
1321 * @chain_signal: per-chain signal strength, in dBm (unlike @signal, doesn't
1322 * support dB or unspecified units)
1323 * @antenna: antenna used
1324 * @rate_idx: index of data rate into band's supported rates or MCS index if
1325 * HT or VHT is used (%RX_FLAG_HT/%RX_FLAG_VHT)
1326 * @nss: number of streams (VHT and HE only)
1327 * @flag: %RX_FLAG_\*
1328 * @encoding: &enum mac80211_rx_encoding
1329 * @bw: &enum rate_info_bw
1330 * @enc_flags: uses bits from &enum mac80211_rx_encoding_flags
1331 * @he_ru: HE RU, from &enum nl80211_he_ru_alloc
1332 * @he_gi: HE GI, from &enum nl80211_he_gi
1333 * @he_dcm: HE DCM value
1334 * @rx_flags: internal RX flags for mac80211
1335 * @ampdu_reference: A-MPDU reference number, must be a different value for
1336 * each A-MPDU but the same for each subframe within one A-MPDU
1337 * @ampdu_delimiter_crc: A-MPDU delimiter CRC
1338 * @zero_length_psdu_type: radiotap type of the 0-length PSDU
1339 */
1340struct ieee80211_rx_status {
1341 u64 mactime;
1342 u64 boottime_ns;
1343 u32 device_timestamp;
1344 u32 ampdu_reference;
1345 u32 flag;
1346 u16 freq;
1347 u8 enc_flags;
1348 u8 encoding:2, bw:3, he_ru:3;
1349 u8 he_gi:2, he_dcm:1;
1350 u8 rate_idx;
1351 u8 nss;
1352 u8 rx_flags;
1353 u8 band;
1354 u8 antenna;
1355 s8 signal;
1356 u8 chains;
1357 s8 chain_signal[IEEE80211_MAX_CHAINS];
1358 u8 ampdu_delimiter_crc;
1359 u8 zero_length_psdu_type;
1360};
1361
1362/**
1363 * struct ieee80211_vendor_radiotap - vendor radiotap data information
1364 * @present: presence bitmap for this vendor namespace
1365 * (this could be extended in the future if any vendor needs more
1366 * bits, the radiotap spec does allow for that)
1367 * @align: radiotap vendor namespace alignment. This defines the needed
1368 * alignment for the @data field below, not for the vendor namespace
1369 * description itself (which has a fixed 2-byte alignment)
1370 * Must be a power of two, and be set to at least 1!
1371 * @oui: radiotap vendor namespace OUI
1372 * @subns: radiotap vendor sub namespace
1373 * @len: radiotap vendor sub namespace skip length, if alignment is done
1374 * then that's added to this, i.e. this is only the length of the
1375 * @data field.
1376 * @pad: number of bytes of padding after the @data, this exists so that
1377 * the skb data alignment can be preserved even if the data has odd
1378 * length
1379 * @data: the actual vendor namespace data
1380 *
1381 * This struct, including the vendor data, goes into the skb->data before
1382 * the 802.11 header. It's split up in mac80211 using the align/oui/subns
1383 * data.
1384 */
1385struct ieee80211_vendor_radiotap {
1386 u32 present;
1387 u8 align;
1388 u8 oui[3];
1389 u8 subns;
1390 u8 pad;
1391 u16 len;
1392 u8 data[];
1393} __packed;
1394
1395/**
1396 * enum ieee80211_conf_flags - configuration flags
1397 *
1398 * Flags to define PHY configuration options
1399 *
1400 * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
1401 * to determine for example whether to calculate timestamps for packets
1402 * or not, do not use instead of filter flags!
1403 * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only).
1404 * This is the power save mode defined by IEEE 802.11-2007 section 11.2,
1405 * meaning that the hardware still wakes up for beacons, is able to
1406 * transmit frames and receive the possible acknowledgment frames.
1407 * Not to be confused with hardware specific wakeup/sleep states,
1408 * driver is responsible for that. See the section "Powersave support"
1409 * for more.
1410 * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
1411 * the driver should be prepared to handle configuration requests but
1412 * may turn the device off as much as possible. Typically, this flag will
1413 * be set when an interface is set UP but not associated or scanning, but
1414 * it can also be unset in that case when monitor interfaces are active.
1415 * @IEEE80211_CONF_OFFCHANNEL: The device is currently not on its main
1416 * operating channel.
1417 */
1418enum ieee80211_conf_flags {
1419 IEEE80211_CONF_MONITOR = (1<<0),
1420 IEEE80211_CONF_PS = (1<<1),
1421 IEEE80211_CONF_IDLE = (1<<2),
1422 IEEE80211_CONF_OFFCHANNEL = (1<<3),
1423};
1424
1425
1426/**
1427 * enum ieee80211_conf_changed - denotes which configuration changed
1428 *
1429 * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
1430 * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed
1431 * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
1432 * @IEEE80211_CONF_CHANGE_POWER: the TX power changed
1433 * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
1434 * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
1435 * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
1436 * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
1437 * Note that this is only valid if channel contexts are not used,
1438 * otherwise each channel context has the number of chains listed.
1439 */
1440enum ieee80211_conf_changed {
1441 IEEE80211_CONF_CHANGE_SMPS = BIT(1),
1442 IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2),
1443 IEEE80211_CONF_CHANGE_MONITOR = BIT(3),
1444 IEEE80211_CONF_CHANGE_PS = BIT(4),
1445 IEEE80211_CONF_CHANGE_POWER = BIT(5),
1446 IEEE80211_CONF_CHANGE_CHANNEL = BIT(6),
1447 IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(7),
1448 IEEE80211_CONF_CHANGE_IDLE = BIT(8),
1449};
1450
1451/**
1452 * enum ieee80211_smps_mode - spatial multiplexing power save mode
1453 *
1454 * @IEEE80211_SMPS_AUTOMATIC: automatic
1455 * @IEEE80211_SMPS_OFF: off
1456 * @IEEE80211_SMPS_STATIC: static
1457 * @IEEE80211_SMPS_DYNAMIC: dynamic
1458 * @IEEE80211_SMPS_NUM_MODES: internal, don't use
1459 */
1460enum ieee80211_smps_mode {
1461 IEEE80211_SMPS_AUTOMATIC,
1462 IEEE80211_SMPS_OFF,
1463 IEEE80211_SMPS_STATIC,
1464 IEEE80211_SMPS_DYNAMIC,
1465
1466 /* keep last */
1467 IEEE80211_SMPS_NUM_MODES,
1468};
1469
1470/**
1471 * struct ieee80211_conf - configuration of the device
1472 *
1473 * This struct indicates how the driver shall configure the hardware.
1474 *
1475 * @flags: configuration flags defined above
1476 *
1477 * @listen_interval: listen interval in units of beacon interval
1478 * @ps_dtim_period: The DTIM period of the AP we're connected to, for use
1479 * in power saving. Power saving will not be enabled until a beacon
1480 * has been received and the DTIM period is known.
1481 * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
1482 * powersave documentation below. This variable is valid only when
1483 * the CONF_PS flag is set.
1484 *
1485 * @power_level: requested transmit power (in dBm), backward compatibility
1486 * value only that is set to the minimum of all interfaces
1487 *
1488 * @chandef: the channel definition to tune to
1489 * @radar_enabled: whether radar detection is enabled
1490 *
1491 * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
1492 * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
1493 * but actually means the number of transmissions not the number of retries
1494 * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
1495 * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
1496 * number of transmissions not the number of retries
1497 *
1498 * @smps_mode: spatial multiplexing powersave mode; note that
1499 * %IEEE80211_SMPS_STATIC is used when the device is not
1500 * configured for an HT channel.
1501 * Note that this is only valid if channel contexts are not used,
1502 * otherwise each channel context has the number of chains listed.
1503 */
1504struct ieee80211_conf {
1505 u32 flags;
1506 int power_level, dynamic_ps_timeout;
1507
1508 u16 listen_interval;
1509 u8 ps_dtim_period;
1510
1511 u8 long_frame_max_tx_count, short_frame_max_tx_count;
1512
1513 struct cfg80211_chan_def chandef;
1514 bool radar_enabled;
1515 enum ieee80211_smps_mode smps_mode;
1516};
1517
1518/**
1519 * struct ieee80211_channel_switch - holds the channel switch data
1520 *
1521 * The information provided in this structure is required for channel switch
1522 * operation.
1523 *
1524 * @timestamp: value in microseconds of the 64-bit Time Synchronization
1525 * Function (TSF) timer when the frame containing the channel switch
1526 * announcement was received. This is simply the rx.mactime parameter
1527 * the driver passed into mac80211.
1528 * @device_timestamp: arbitrary timestamp for the device, this is the
1529 * rx.device_timestamp parameter the driver passed to mac80211.
1530 * @block_tx: Indicates whether transmission must be blocked before the
1531 * scheduled channel switch, as indicated by the AP.
1532 * @chandef: the new channel to switch to
1533 * @count: the number of TBTT's until the channel switch event
1534 * @delay: maximum delay between the time the AP transmitted the last beacon in
1535 * current channel and the expected time of the first beacon in the new
1536 * channel, expressed in TU.
1537 */
1538struct ieee80211_channel_switch {
1539 u64 timestamp;
1540 u32 device_timestamp;
1541 bool block_tx;
1542 struct cfg80211_chan_def chandef;
1543 u8 count;
1544 u32 delay;
1545};
1546
1547/**
1548 * enum ieee80211_vif_flags - virtual interface flags
1549 *
1550 * @IEEE80211_VIF_BEACON_FILTER: the device performs beacon filtering
1551 * on this virtual interface to avoid unnecessary CPU wakeups
1552 * @IEEE80211_VIF_SUPPORTS_CQM_RSSI: the device can do connection quality
1553 * monitoring on this virtual interface -- i.e. it can monitor
1554 * connection quality related parameters, such as the RSSI level and
1555 * provide notifications if configured trigger levels are reached.
1556 * @IEEE80211_VIF_SUPPORTS_UAPSD: The device can do U-APSD for this
1557 * interface. This flag should be set during interface addition,
1558 * but may be set/cleared as late as authentication to an AP. It is
1559 * only valid for managed/station mode interfaces.
1560 * @IEEE80211_VIF_GET_NOA_UPDATE: request to handle NOA attributes
1561 * and send P2P_PS notification to the driver if NOA changed, even
1562 * this is not pure P2P vif.
1563 */
1564enum ieee80211_vif_flags {
1565 IEEE80211_VIF_BEACON_FILTER = BIT(0),
1566 IEEE80211_VIF_SUPPORTS_CQM_RSSI = BIT(1),
1567 IEEE80211_VIF_SUPPORTS_UAPSD = BIT(2),
1568 IEEE80211_VIF_GET_NOA_UPDATE = BIT(3),
1569};
1570
1571/**
1572 * struct ieee80211_vif - per-interface data
1573 *
1574 * Data in this structure is continually present for driver
1575 * use during the life of a virtual interface.
1576 *
1577 * @type: type of this virtual interface
1578 * @bss_conf: BSS configuration for this interface, either our own
1579 * or the BSS we're associated to
1580 * @addr: address of this interface
1581 * @p2p: indicates whether this AP or STA interface is a p2p
1582 * interface, i.e. a GO or p2p-sta respectively
1583 * @csa_active: marks whether a channel switch is going on. Internally it is
1584 * write-protected by sdata_lock and local->mtx so holding either is fine
1585 * for read access.
1586 * @mu_mimo_owner: indicates interface owns MU-MIMO capability
1587 * @driver_flags: flags/capabilities the driver has for this interface,
1588 * these need to be set (or cleared) when the interface is added
1589 * or, if supported by the driver, the interface type is changed
1590 * at runtime, mac80211 will never touch this field
1591 * @hw_queue: hardware queue for each AC
1592 * @cab_queue: content-after-beacon (DTIM beacon really) queue, AP mode only
1593 * @chanctx_conf: The channel context this interface is assigned to, or %NULL
1594 * when it is not assigned. This pointer is RCU-protected due to the TX
1595 * path needing to access it; even though the netdev carrier will always
1596 * be off when it is %NULL there can still be races and packets could be
1597 * processed after it switches back to %NULL.
1598 * @debugfs_dir: debugfs dentry, can be used by drivers to create own per
1599 * interface debug files. Note that it will be NULL for the virtual
1600 * monitor interface (if that is requested.)
1601 * @probe_req_reg: probe requests should be reported to mac80211 for this
1602 * interface.
1603 * @drv_priv: data area for driver use, will always be aligned to
1604 * sizeof(void \*).
1605 * @txq: the multicast data TX queue (if driver uses the TXQ abstraction)
1606 * @txqs_stopped: per AC flag to indicate that intermediate TXQs are stopped,
1607 * protected by fq->lock.
1608 */
1609struct ieee80211_vif {
1610 enum nl80211_iftype type;
1611 struct ieee80211_bss_conf bss_conf;
1612 u8 addr[ETH_ALEN] __aligned(2);
1613 bool p2p;
1614 bool csa_active;
1615 bool mu_mimo_owner;
1616
1617 u8 cab_queue;
1618 u8 hw_queue[IEEE80211_NUM_ACS];
1619
1620 struct ieee80211_txq *txq;
1621
1622 struct ieee80211_chanctx_conf __rcu *chanctx_conf;
1623
1624 u32 driver_flags;
1625
1626#ifdef CONFIG_MAC80211_DEBUGFS
1627 struct dentry *debugfs_dir;
1628#endif
1629
1630 unsigned int probe_req_reg;
1631
1632 bool txqs_stopped[IEEE80211_NUM_ACS];
1633
1634 /* must be last */
1635 u8 drv_priv[0] __aligned(sizeof(void *));
1636};
1637
1638static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
1639{
1640#ifdef CONFIG_MAC80211_MESH
1641 return vif->type == NL80211_IFTYPE_MESH_POINT;
1642#endif
1643 return false;
1644}
1645
1646/**
1647 * wdev_to_ieee80211_vif - return a vif struct from a wdev
1648 * @wdev: the wdev to get the vif for
1649 *
1650 * This can be used by mac80211 drivers with direct cfg80211 APIs
1651 * (like the vendor commands) that get a wdev.
1652 *
1653 * Note that this function may return %NULL if the given wdev isn't
1654 * associated with a vif that the driver knows about (e.g. monitor
1655 * or AP_VLAN interfaces.)
1656 */
1657struct ieee80211_vif *wdev_to_ieee80211_vif(struct wireless_dev *wdev);
1658
1659/**
1660 * ieee80211_vif_to_wdev - return a wdev struct from a vif
1661 * @vif: the vif to get the wdev for
1662 *
1663 * This can be used by mac80211 drivers with direct cfg80211 APIs
1664 * (like the vendor commands) that needs to get the wdev for a vif.
1665 *
1666 * Note that this function may return %NULL if the given wdev isn't
1667 * associated with a vif that the driver knows about (e.g. monitor
1668 * or AP_VLAN interfaces.)
1669 */
1670struct wireless_dev *ieee80211_vif_to_wdev(struct ieee80211_vif *vif);
1671
1672/**
1673 * enum ieee80211_key_flags - key flags
1674 *
1675 * These flags are used for communication about keys between the driver
1676 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
1677 *
1678 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
1679 * driver to indicate that it requires IV generation for this
1680 * particular key. Setting this flag does not necessarily mean that SKBs
1681 * will have sufficient tailroom for ICV or MIC.
1682 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
1683 * the driver for a TKIP key if it requires Michael MIC
1684 * generation in software.
1685 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
1686 * that the key is pairwise rather then a shared key.
1687 * @IEEE80211_KEY_FLAG_SW_MGMT_TX: This flag should be set by the driver for a
1688 * CCMP/GCMP key if it requires CCMP/GCMP encryption of management frames
1689 * (MFP) to be done in software.
1690 * @IEEE80211_KEY_FLAG_PUT_IV_SPACE: This flag should be set by the driver
1691 * if space should be prepared for the IV, but the IV
1692 * itself should not be generated. Do not set together with
1693 * @IEEE80211_KEY_FLAG_GENERATE_IV on the same key. Setting this flag does
1694 * not necessarily mean that SKBs will have sufficient tailroom for ICV or
1695 * MIC.
1696 * @IEEE80211_KEY_FLAG_RX_MGMT: This key will be used to decrypt received
1697 * management frames. The flag can help drivers that have a hardware
1698 * crypto implementation that doesn't deal with management frames
1699 * properly by allowing them to not upload the keys to hardware and
1700 * fall back to software crypto. Note that this flag deals only with
1701 * RX, if your crypto engine can't deal with TX you can also set the
1702 * %IEEE80211_KEY_FLAG_SW_MGMT_TX flag to encrypt such frames in SW.
1703 * @IEEE80211_KEY_FLAG_GENERATE_IV_MGMT: This flag should be set by the
1704 * driver for a CCMP/GCMP key to indicate that is requires IV generation
1705 * only for managment frames (MFP).
1706 * @IEEE80211_KEY_FLAG_RESERVE_TAILROOM: This flag should be set by the
1707 * driver for a key to indicate that sufficient tailroom must always
1708 * be reserved for ICV or MIC, even when HW encryption is enabled.
1709 * @IEEE80211_KEY_FLAG_PUT_MIC_SPACE: This flag should be set by the driver for
1710 * a TKIP key if it only requires MIC space. Do not set together with
1711 * @IEEE80211_KEY_FLAG_GENERATE_MMIC on the same key.
1712 * @IEEE80211_KEY_FLAG_NO_AUTO_TX: Key needs explicit Tx activation.
1713 * @IEEE80211_KEY_FLAG_GENERATE_MMIE: This flag should be set by the driver
1714 * for a AES_CMAC key to indicate that it requires sequence number
1715 * generation only
1716 */
1717enum ieee80211_key_flags {
1718 IEEE80211_KEY_FLAG_GENERATE_IV_MGMT = BIT(0),
1719 IEEE80211_KEY_FLAG_GENERATE_IV = BIT(1),
1720 IEEE80211_KEY_FLAG_GENERATE_MMIC = BIT(2),
1721 IEEE80211_KEY_FLAG_PAIRWISE = BIT(3),
1722 IEEE80211_KEY_FLAG_SW_MGMT_TX = BIT(4),
1723 IEEE80211_KEY_FLAG_PUT_IV_SPACE = BIT(5),
1724 IEEE80211_KEY_FLAG_RX_MGMT = BIT(6),
1725 IEEE80211_KEY_FLAG_RESERVE_TAILROOM = BIT(7),
1726 IEEE80211_KEY_FLAG_PUT_MIC_SPACE = BIT(8),
1727 IEEE80211_KEY_FLAG_NO_AUTO_TX = BIT(9),
1728 IEEE80211_KEY_FLAG_GENERATE_MMIE = BIT(10),
1729};
1730
1731/**
1732 * struct ieee80211_key_conf - key information
1733 *
1734 * This key information is given by mac80211 to the driver by
1735 * the set_key() callback in &struct ieee80211_ops.
1736 *
1737 * @hw_key_idx: To be set by the driver, this is the key index the driver
1738 * wants to be given when a frame is transmitted and needs to be
1739 * encrypted in hardware.
1740 * @cipher: The key's cipher suite selector.
1741 * @tx_pn: PN used for TX keys, may be used by the driver as well if it
1742 * needs to do software PN assignment by itself (e.g. due to TSO)
1743 * @flags: key flags, see &enum ieee80211_key_flags.
1744 * @keyidx: the key index (0-3)
1745 * @keylen: key material length
1746 * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
1747 * data block:
1748 * - Temporal Encryption Key (128 bits)
1749 * - Temporal Authenticator Tx MIC Key (64 bits)
1750 * - Temporal Authenticator Rx MIC Key (64 bits)
1751 * @icv_len: The ICV length for this key type
1752 * @iv_len: The IV length for this key type
1753 */
1754struct ieee80211_key_conf {
1755 atomic64_t tx_pn;
1756 u32 cipher;
1757 u8 icv_len;
1758 u8 iv_len;
1759 u8 hw_key_idx;
1760 s8 keyidx;
1761 u16 flags;
1762 u8 keylen;
1763 u8 key[0];
1764};
1765
1766#define IEEE80211_MAX_PN_LEN 16
1767
1768#define TKIP_PN_TO_IV16(pn) ((u16)(pn & 0xffff))
1769#define TKIP_PN_TO_IV32(pn) ((u32)((pn >> 16) & 0xffffffff))
1770
1771/**
1772 * struct ieee80211_key_seq - key sequence counter
1773 *
1774 * @tkip: TKIP data, containing IV32 and IV16 in host byte order
1775 * @ccmp: PN data, most significant byte first (big endian,
1776 * reverse order than in packet)
1777 * @aes_cmac: PN data, most significant byte first (big endian,
1778 * reverse order than in packet)
1779 * @aes_gmac: PN data, most significant byte first (big endian,
1780 * reverse order than in packet)
1781 * @gcmp: PN data, most significant byte first (big endian,
1782 * reverse order than in packet)
1783 * @hw: data for HW-only (e.g. cipher scheme) keys
1784 */
1785struct ieee80211_key_seq {
1786 union {
1787 struct {
1788 u32 iv32;
1789 u16 iv16;
1790 } tkip;
1791 struct {
1792 u8 pn[6];
1793 } ccmp;
1794 struct {
1795 u8 pn[6];
1796 } aes_cmac;
1797 struct {
1798 u8 pn[6];
1799 } aes_gmac;
1800 struct {
1801 u8 pn[6];
1802 } gcmp;
1803 struct {
1804 u8 seq[IEEE80211_MAX_PN_LEN];
1805 u8 seq_len;
1806 } hw;
1807 };
1808};
1809
1810/**
1811 * struct ieee80211_cipher_scheme - cipher scheme
1812 *
1813 * This structure contains a cipher scheme information defining
1814 * the secure packet crypto handling.
1815 *
1816 * @cipher: a cipher suite selector
1817 * @iftype: a cipher iftype bit mask indicating an allowed cipher usage
1818 * @hdr_len: a length of a security header used the cipher
1819 * @pn_len: a length of a packet number in the security header
1820 * @pn_off: an offset of pn from the beginning of the security header
1821 * @key_idx_off: an offset of key index byte in the security header
1822 * @key_idx_mask: a bit mask of key_idx bits
1823 * @key_idx_shift: a bit shift needed to get key_idx
1824 * key_idx value calculation:
1825 * (sec_header_base[key_idx_off] & key_idx_mask) >> key_idx_shift
1826 * @mic_len: a mic length in bytes
1827 */
1828struct ieee80211_cipher_scheme {
1829 u32 cipher;
1830 u16 iftype;
1831 u8 hdr_len;
1832 u8 pn_len;
1833 u8 pn_off;
1834 u8 key_idx_off;
1835 u8 key_idx_mask;
1836 u8 key_idx_shift;
1837 u8 mic_len;
1838};
1839
1840/**
1841 * enum set_key_cmd - key command
1842 *
1843 * Used with the set_key() callback in &struct ieee80211_ops, this
1844 * indicates whether a key is being removed or added.
1845 *
1846 * @SET_KEY: a key is set
1847 * @DISABLE_KEY: a key must be disabled
1848 */
1849enum set_key_cmd {
1850 SET_KEY, DISABLE_KEY,
1851};
1852
1853/**
1854 * enum ieee80211_sta_state - station state
1855 *
1856 * @IEEE80211_STA_NOTEXIST: station doesn't exist at all,
1857 * this is a special state for add/remove transitions
1858 * @IEEE80211_STA_NONE: station exists without special state
1859 * @IEEE80211_STA_AUTH: station is authenticated
1860 * @IEEE80211_STA_ASSOC: station is associated
1861 * @IEEE80211_STA_AUTHORIZED: station is authorized (802.1X)
1862 */
1863enum ieee80211_sta_state {
1864 /* NOTE: These need to be ordered correctly! */
1865 IEEE80211_STA_NOTEXIST,
1866 IEEE80211_STA_NONE,
1867 IEEE80211_STA_AUTH,
1868 IEEE80211_STA_ASSOC,
1869 IEEE80211_STA_AUTHORIZED,
1870};
1871
1872/**
1873 * enum ieee80211_sta_rx_bandwidth - station RX bandwidth
1874 * @IEEE80211_STA_RX_BW_20: station can only receive 20 MHz
1875 * @IEEE80211_STA_RX_BW_40: station can receive up to 40 MHz
1876 * @IEEE80211_STA_RX_BW_80: station can receive up to 80 MHz
1877 * @IEEE80211_STA_RX_BW_160: station can receive up to 160 MHz
1878 * (including 80+80 MHz)
1879 *
1880 * Implementation note: 20 must be zero to be initialized
1881 * correctly, the values must be sorted.
1882 */
1883enum ieee80211_sta_rx_bandwidth {
1884 IEEE80211_STA_RX_BW_20 = 0,
1885 IEEE80211_STA_RX_BW_40,
1886 IEEE80211_STA_RX_BW_80,
1887 IEEE80211_STA_RX_BW_160,
1888};
1889
1890/**
1891 * struct ieee80211_sta_rates - station rate selection table
1892 *
1893 * @rcu_head: RCU head used for freeing the table on update
1894 * @rate: transmit rates/flags to be used by default.
1895 * Overriding entries per-packet is possible by using cb tx control.
1896 */
1897struct ieee80211_sta_rates {
1898 struct rcu_head rcu_head;
1899 struct {
1900 s8 idx;
1901 u8 count;
1902 u8 count_cts;
1903 u8 count_rts;
1904 u16 flags;
1905 } rate[IEEE80211_TX_RATE_TABLE_SIZE];
1906};
1907
1908/**
1909 * struct ieee80211_sta_txpwr - station txpower configuration
1910 *
1911 * Used to configure txpower for station.
1912 *
1913 * @power: indicates the tx power, in dBm, to be used when sending data frames
1914 * to the STA.
1915 * @type: In particular if TPC %type is NL80211_TX_POWER_LIMITED then tx power
1916 * will be less than or equal to specified from userspace, whereas if TPC
1917 * %type is NL80211_TX_POWER_AUTOMATIC then it indicates default tx power.
1918 * NL80211_TX_POWER_FIXED is not a valid configuration option for
1919 * per peer TPC.
1920 */
1921struct ieee80211_sta_txpwr {
1922 s16 power;
1923 enum nl80211_tx_power_setting type;
1924};
1925
1926/**
1927 * struct ieee80211_sta - station table entry
1928 *
1929 * A station table entry represents a station we are possibly
1930 * communicating with. Since stations are RCU-managed in
1931 * mac80211, any ieee80211_sta pointer you get access to must
1932 * either be protected by rcu_read_lock() explicitly or implicitly,
1933 * or you must take good care to not use such a pointer after a
1934 * call to your sta_remove callback that removed it.
1935 *
1936 * @addr: MAC address
1937 * @aid: AID we assigned to the station if we're an AP
1938 * @supp_rates: Bitmap of supported rates (per band)
1939 * @ht_cap: HT capabilities of this STA; restricted to our own capabilities
1940 * @vht_cap: VHT capabilities of this STA; restricted to our own capabilities
1941 * @he_cap: HE capabilities of this STA
1942 * @max_rx_aggregation_subframes: maximal amount of frames in a single AMPDU
1943 * that this station is allowed to transmit to us.
1944 * Can be modified by driver.
1945 * @wme: indicates whether the STA supports QoS/WME (if local devices does,
1946 * otherwise always false)
1947 * @drv_priv: data area for driver use, will always be aligned to
1948 * sizeof(void \*), size is determined in hw information.
1949 * @uapsd_queues: bitmap of queues configured for uapsd. Only valid
1950 * if wme is supported. The bits order is like in
1951 * IEEE80211_WMM_IE_STA_QOSINFO_AC_*.
1952 * @max_sp: max Service Period. Only valid if wme is supported.
1953 * @bandwidth: current bandwidth the station can receive with
1954 * @rx_nss: in HT/VHT, the maximum number of spatial streams the
1955 * station can receive at the moment, changed by operating mode
1956 * notifications and capabilities. The value is only valid after
1957 * the station moves to associated state.
1958 * @smps_mode: current SMPS mode (off, static or dynamic)
1959 * @rates: rate control selection table
1960 * @tdls: indicates whether the STA is a TDLS peer
1961 * @tdls_initiator: indicates the STA is an initiator of the TDLS link. Only
1962 * valid if the STA is a TDLS peer in the first place.
1963 * @mfp: indicates whether the STA uses management frame protection or not.
1964 * @max_amsdu_subframes: indicates the maximal number of MSDUs in a single
1965 * A-MSDU. Taken from the Extended Capabilities element. 0 means
1966 * unlimited.
1967 * @support_p2p_ps: indicates whether the STA supports P2P PS mechanism or not.
1968 * @max_rc_amsdu_len: Maximum A-MSDU size in bytes recommended by rate control.
1969 * @max_tid_amsdu_len: Maximum A-MSDU size in bytes for this TID
1970 * @txq: per-TID data TX queues (if driver uses the TXQ abstraction); note that
1971 * the last entry (%IEEE80211_NUM_TIDS) is used for non-data frames
1972 */
1973struct ieee80211_sta {
1974 u32 supp_rates[NUM_NL80211_BANDS];
1975 u8 addr[ETH_ALEN];
1976 u16 aid;
1977 struct ieee80211_sta_ht_cap ht_cap;
1978 struct ieee80211_sta_vht_cap vht_cap;
1979 struct ieee80211_sta_he_cap he_cap;
1980 u16 max_rx_aggregation_subframes;
1981 bool wme;
1982 u8 uapsd_queues;
1983 u8 max_sp;
1984 u8 rx_nss;
1985 enum ieee80211_sta_rx_bandwidth bandwidth;
1986 enum ieee80211_smps_mode smps_mode;
1987 struct ieee80211_sta_rates __rcu *rates;
1988 bool tdls;
1989 bool tdls_initiator;
1990 bool mfp;
1991 u8 max_amsdu_subframes;
1992
1993 /**
1994 * @max_amsdu_len:
1995 * indicates the maximal length of an A-MSDU in bytes.
1996 * This field is always valid for packets with a VHT preamble.
1997 * For packets with a HT preamble, additional limits apply:
1998 *
1999 * * If the skb is transmitted as part of a BA agreement, the
2000 * A-MSDU maximal size is min(max_amsdu_len, 4065) bytes.
2001 * * If the skb is not part of a BA aggreement, the A-MSDU maximal
2002 * size is min(max_amsdu_len, 7935) bytes.
2003 *
2004 * Both additional HT limits must be enforced by the low level
2005 * driver. This is defined by the spec (IEEE 802.11-2012 section
2006 * 8.3.2.2 NOTE 2).
2007 */
2008 u16 max_amsdu_len;
2009 bool support_p2p_ps;
2010 u16 max_rc_amsdu_len;
2011 u16 max_tid_amsdu_len[IEEE80211_NUM_TIDS];
2012 struct ieee80211_sta_txpwr txpwr;
2013
2014 struct ieee80211_txq *txq[IEEE80211_NUM_TIDS + 1];
2015
2016 /* must be last */
2017 u8 drv_priv[0] __aligned(sizeof(void *));
2018};
2019
2020/**
2021 * enum sta_notify_cmd - sta notify command
2022 *
2023 * Used with the sta_notify() callback in &struct ieee80211_ops, this
2024 * indicates if an associated station made a power state transition.
2025 *
2026 * @STA_NOTIFY_SLEEP: a station is now sleeping
2027 * @STA_NOTIFY_AWAKE: a sleeping station woke up
2028 */
2029enum sta_notify_cmd {
2030 STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
2031};
2032
2033/**
2034 * struct ieee80211_tx_control - TX control data
2035 *
2036 * @sta: station table entry, this sta pointer may be NULL and
2037 * it is not allowed to copy the pointer, due to RCU.
2038 */
2039struct ieee80211_tx_control {
2040 struct ieee80211_sta *sta;
2041};
2042
2043/**
2044 * struct ieee80211_txq - Software intermediate tx queue
2045 *
2046 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
2047 * @sta: station table entry, %NULL for per-vif queue
2048 * @tid: the TID for this queue (unused for per-vif queue),
2049 * %IEEE80211_NUM_TIDS for non-data (if enabled)
2050 * @ac: the AC for this queue
2051 * @drv_priv: driver private area, sized by hw->txq_data_size
2052 *
2053 * The driver can obtain packets from this queue by calling
2054 * ieee80211_tx_dequeue().
2055 */
2056struct ieee80211_txq {
2057 struct ieee80211_vif *vif;
2058 struct ieee80211_sta *sta;
2059 u8 tid;
2060 u8 ac;
2061
2062 /* must be last */
2063 u8 drv_priv[0] __aligned(sizeof(void *));
2064};
2065
2066/**
2067 * enum ieee80211_hw_flags - hardware flags
2068 *
2069 * These flags are used to indicate hardware capabilities to
2070 * the stack. Generally, flags here should have their meaning
2071 * done in a way that the simplest hardware doesn't need setting
2072 * any particular flags. There are some exceptions to this rule,
2073 * however, so you are advised to review these flags carefully.
2074 *
2075 * @IEEE80211_HW_HAS_RATE_CONTROL:
2076 * The hardware or firmware includes rate control, and cannot be
2077 * controlled by the stack. As such, no rate control algorithm
2078 * should be instantiated, and the TX rate reported to userspace
2079 * will be taken from the TX status instead of the rate control
2080 * algorithm.
2081 * Note that this requires that the driver implement a number of
2082 * callbacks so it has the correct information, it needs to have
2083 * the @set_rts_threshold callback and must look at the BSS config
2084 * @use_cts_prot for G/N protection, @use_short_slot for slot
2085 * timing in 2.4 GHz and @use_short_preamble for preambles for
2086 * CCK frames.
2087 *
2088 * @IEEE80211_HW_RX_INCLUDES_FCS:
2089 * Indicates that received frames passed to the stack include
2090 * the FCS at the end.
2091 *
2092 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
2093 * Some wireless LAN chipsets buffer broadcast/multicast frames
2094 * for power saving stations in the hardware/firmware and others
2095 * rely on the host system for such buffering. This option is used
2096 * to configure the IEEE 802.11 upper layer to buffer broadcast and
2097 * multicast frames when there are power saving stations so that
2098 * the driver can fetch them with ieee80211_get_buffered_bc().
2099 *
2100 * @IEEE80211_HW_SIGNAL_UNSPEC:
2101 * Hardware can provide signal values but we don't know its units. We
2102 * expect values between 0 and @max_signal.
2103 * If possible please provide dB or dBm instead.
2104 *
2105 * @IEEE80211_HW_SIGNAL_DBM:
2106 * Hardware gives signal values in dBm, decibel difference from
2107 * one milliwatt. This is the preferred method since it is standardized
2108 * between different devices. @max_signal does not need to be set.
2109 *
2110 * @IEEE80211_HW_SPECTRUM_MGMT:
2111 * Hardware supports spectrum management defined in 802.11h
2112 * Measurement, Channel Switch, Quieting, TPC
2113 *
2114 * @IEEE80211_HW_AMPDU_AGGREGATION:
2115 * Hardware supports 11n A-MPDU aggregation.
2116 *
2117 * @IEEE80211_HW_SUPPORTS_PS:
2118 * Hardware has power save support (i.e. can go to sleep).
2119 *
2120 * @IEEE80211_HW_PS_NULLFUNC_STACK:
2121 * Hardware requires nullfunc frame handling in stack, implies
2122 * stack support for dynamic PS.
2123 *
2124 * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
2125 * Hardware has support for dynamic PS.
2126 *
2127 * @IEEE80211_HW_MFP_CAPABLE:
2128 * Hardware supports management frame protection (MFP, IEEE 802.11w).
2129 *
2130 * @IEEE80211_HW_REPORTS_TX_ACK_STATUS:
2131 * Hardware can provide ack status reports of Tx frames to
2132 * the stack.
2133 *
2134 * @IEEE80211_HW_CONNECTION_MONITOR:
2135 * The hardware performs its own connection monitoring, including
2136 * periodic keep-alives to the AP and probing the AP on beacon loss.
2137 *
2138 * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC:
2139 * This device needs to get data from beacon before association (i.e.
2140 * dtim_period).
2141 *
2142 * @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports
2143 * per-station GTKs as used by IBSS RSN or during fast transition. If
2144 * the device doesn't support per-station GTKs, but can be asked not
2145 * to decrypt group addressed frames, then IBSS RSN support is still
2146 * possible but software crypto will be used. Advertise the wiphy flag
2147 * only in that case.
2148 *
2149 * @IEEE80211_HW_AP_LINK_PS: When operating in AP mode the device
2150 * autonomously manages the PS status of connected stations. When
2151 * this flag is set mac80211 will not trigger PS mode for connected
2152 * stations based on the PM bit of incoming frames.
2153 * Use ieee80211_start_ps()/ieee8021_end_ps() to manually configure
2154 * the PS mode of connected stations.
2155 *
2156 * @IEEE80211_HW_TX_AMPDU_SETUP_IN_HW: The device handles TX A-MPDU session
2157 * setup strictly in HW. mac80211 should not attempt to do this in
2158 * software.
2159 *
2160 * @IEEE80211_HW_WANT_MONITOR_VIF: The driver would like to be informed of
2161 * a virtual monitor interface when monitor interfaces are the only
2162 * active interfaces.
2163 *
2164 * @IEEE80211_HW_NO_AUTO_VIF: The driver would like for no wlanX to
2165 * be created. It is expected user-space will create vifs as
2166 * desired (and thus have them named as desired).
2167 *
2168 * @IEEE80211_HW_SW_CRYPTO_CONTROL: The driver wants to control which of the
2169 * crypto algorithms can be done in software - so don't automatically
2170 * try to fall back to it if hardware crypto fails, but do so only if
2171 * the driver returns 1. This also forces the driver to advertise its
2172 * supported cipher suites.
2173 *
2174 * @IEEE80211_HW_SUPPORT_FAST_XMIT: The driver/hardware supports fast-xmit,
2175 * this currently requires only the ability to calculate the duration
2176 * for frames.
2177 *
2178 * @IEEE80211_HW_QUEUE_CONTROL: The driver wants to control per-interface
2179 * queue mapping in order to use different queues (not just one per AC)
2180 * for different virtual interfaces. See the doc section on HW queue
2181 * control for more details.
2182 *
2183 * @IEEE80211_HW_SUPPORTS_RC_TABLE: The driver supports using a rate
2184 * selection table provided by the rate control algorithm.
2185 *
2186 * @IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF: Use the P2P Device address for any
2187 * P2P Interface. This will be honoured even if more than one interface
2188 * is supported.
2189 *
2190 * @IEEE80211_HW_TIMING_BEACON_ONLY: Use sync timing from beacon frames
2191 * only, to allow getting TBTT of a DTIM beacon.
2192 *
2193 * @IEEE80211_HW_SUPPORTS_HT_CCK_RATES: Hardware supports mixing HT/CCK rates
2194 * and can cope with CCK rates in an aggregation session (e.g. by not
2195 * using aggregation for such frames.)
2196 *
2197 * @IEEE80211_HW_CHANCTX_STA_CSA: Support 802.11h based channel-switch (CSA)
2198 * for a single active channel while using channel contexts. When support
2199 * is not enabled the default action is to disconnect when getting the
2200 * CSA frame.
2201 *
2202 * @IEEE80211_HW_SUPPORTS_CLONED_SKBS: The driver will never modify the payload
2203 * or tailroom of TX skbs without copying them first.
2204 *
2205 * @IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS: The HW supports scanning on all bands
2206 * in one command, mac80211 doesn't have to run separate scans per band.
2207 *
2208 * @IEEE80211_HW_TDLS_WIDER_BW: The device/driver supports wider bandwidth
2209 * than then BSS bandwidth for a TDLS link on the base channel.
2210 *
2211 * @IEEE80211_HW_SUPPORTS_AMSDU_IN_AMPDU: The driver supports receiving A-MSDUs
2212 * within A-MPDU.
2213 *
2214 * @IEEE80211_HW_BEACON_TX_STATUS: The device/driver provides TX status
2215 * for sent beacons.
2216 *
2217 * @IEEE80211_HW_NEEDS_UNIQUE_STA_ADDR: Hardware (or driver) requires that each
2218 * station has a unique address, i.e. each station entry can be identified
2219 * by just its MAC address; this prevents, for example, the same station
2220 * from connecting to two virtual AP interfaces at the same time.
2221 *
2222 * @IEEE80211_HW_SUPPORTS_REORDERING_BUFFER: Hardware (or driver) manages the
2223 * reordering buffer internally, guaranteeing mac80211 receives frames in
2224 * order and does not need to manage its own reorder buffer or BA session
2225 * timeout.
2226 *
2227 * @IEEE80211_HW_USES_RSS: The device uses RSS and thus requires parallel RX,
2228 * which implies using per-CPU station statistics.
2229 *
2230 * @IEEE80211_HW_TX_AMSDU: Hardware (or driver) supports software aggregated
2231 * A-MSDU frames. Requires software tx queueing and fast-xmit support.
2232 * When not using minstrel/minstrel_ht rate control, the driver must
2233 * limit the maximum A-MSDU size based on the current tx rate by setting
2234 * max_rc_amsdu_len in struct ieee80211_sta.
2235 *
2236 * @IEEE80211_HW_TX_FRAG_LIST: Hardware (or driver) supports sending frag_list
2237 * skbs, needed for zero-copy software A-MSDU.
2238 *
2239 * @IEEE80211_HW_REPORTS_LOW_ACK: The driver (or firmware) reports low ack event
2240 * by ieee80211_report_low_ack() based on its own algorithm. For such
2241 * drivers, mac80211 packet loss mechanism will not be triggered and driver
2242 * is completely depending on firmware event for station kickout.
2243 *
2244 * @IEEE80211_HW_SUPPORTS_TX_FRAG: Hardware does fragmentation by itself.
2245 * The stack will not do fragmentation.
2246 * The callback for @set_frag_threshold should be set as well.
2247 *
2248 * @IEEE80211_HW_SUPPORTS_TDLS_BUFFER_STA: Hardware supports buffer STA on
2249 * TDLS links.
2250 *
2251 * @IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP: The driver requires the
2252 * mgd_prepare_tx() callback to be called before transmission of a
2253 * deauthentication frame in case the association was completed but no
2254 * beacon was heard. This is required in multi-channel scenarios, where the
2255 * virtual interface might not be given air time for the transmission of
2256 * the frame, as it is not synced with the AP/P2P GO yet, and thus the
2257 * deauthentication frame might not be transmitted.
2258 *
2259 * @IEEE80211_HW_DOESNT_SUPPORT_QOS_NDP: The driver (or firmware) doesn't
2260 * support QoS NDP for AP probing - that's most likely a driver bug.
2261 *
2262 * @IEEE80211_HW_BUFF_MMPDU_TXQ: use the TXQ for bufferable MMPDUs, this of
2263 * course requires the driver to use TXQs to start with.
2264 *
2265 * @IEEE80211_HW_SUPPORTS_VHT_EXT_NSS_BW: (Hardware) rate control supports VHT
2266 * extended NSS BW (dot11VHTExtendedNSSBWCapable). This flag will be set if
2267 * the selected rate control algorithm sets %RATE_CTRL_CAPA_VHT_EXT_NSS_BW
2268 * but if the rate control is built-in then it must be set by the driver.
2269 * See also the documentation for that flag.
2270 *
2271 * @IEEE80211_HW_STA_MMPDU_TXQ: use the extra non-TID per-station TXQ for all
2272 * MMPDUs on station interfaces. This of course requires the driver to use
2273 * TXQs to start with.
2274 *
2275 * @IEEE80211_HW_TX_STATUS_NO_AMPDU_LEN: Driver does not report accurate A-MPDU
2276 * length in tx status information
2277 *
2278 * @IEEE80211_HW_SUPPORTS_MULTI_BSSID: Hardware supports multi BSSID
2279 *
2280 * @IEEE80211_HW_SUPPORTS_ONLY_HE_MULTI_BSSID: Hardware supports multi BSSID
2281 * only for HE APs. Applies if @IEEE80211_HW_SUPPORTS_MULTI_BSSID is set.
2282 *
2283 * @IEEE80211_HW_AMPDU_KEYBORDER_SUPPORT: The card and driver is only
2284 * aggregating MPDUs with the same keyid, allowing mac80211 to keep Tx
2285 * A-MPDU sessions active while rekeying with Extended Key ID.
2286 *
2287 * @NUM_IEEE80211_HW_FLAGS: number of hardware flags, used for sizing arrays
2288 */
2289enum ieee80211_hw_flags {
2290 IEEE80211_HW_HAS_RATE_CONTROL,
2291 IEEE80211_HW_RX_INCLUDES_FCS,
2292 IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING,
2293 IEEE80211_HW_SIGNAL_UNSPEC,
2294 IEEE80211_HW_SIGNAL_DBM,
2295 IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC,
2296 IEEE80211_HW_SPECTRUM_MGMT,
2297 IEEE80211_HW_AMPDU_AGGREGATION,
2298 IEEE80211_HW_SUPPORTS_PS,
2299 IEEE80211_HW_PS_NULLFUNC_STACK,
2300 IEEE80211_HW_SUPPORTS_DYNAMIC_PS,
2301 IEEE80211_HW_MFP_CAPABLE,
2302 IEEE80211_HW_WANT_MONITOR_VIF,
2303 IEEE80211_HW_NO_AUTO_VIF,
2304 IEEE80211_HW_SW_CRYPTO_CONTROL,
2305 IEEE80211_HW_SUPPORT_FAST_XMIT,
2306 IEEE80211_HW_REPORTS_TX_ACK_STATUS,
2307 IEEE80211_HW_CONNECTION_MONITOR,
2308 IEEE80211_HW_QUEUE_CONTROL,
2309 IEEE80211_HW_SUPPORTS_PER_STA_GTK,
2310 IEEE80211_HW_AP_LINK_PS,
2311 IEEE80211_HW_TX_AMPDU_SETUP_IN_HW,
2312 IEEE80211_HW_SUPPORTS_RC_TABLE,
2313 IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF,
2314 IEEE80211_HW_TIMING_BEACON_ONLY,
2315 IEEE80211_HW_SUPPORTS_HT_CCK_RATES,
2316 IEEE80211_HW_CHANCTX_STA_CSA,
2317 IEEE80211_HW_SUPPORTS_CLONED_SKBS,
2318 IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS,
2319 IEEE80211_HW_TDLS_WIDER_BW,
2320 IEEE80211_HW_SUPPORTS_AMSDU_IN_AMPDU,
2321 IEEE80211_HW_BEACON_TX_STATUS,
2322 IEEE80211_HW_NEEDS_UNIQUE_STA_ADDR,
2323 IEEE80211_HW_SUPPORTS_REORDERING_BUFFER,
2324 IEEE80211_HW_USES_RSS,
2325 IEEE80211_HW_TX_AMSDU,
2326 IEEE80211_HW_TX_FRAG_LIST,
2327 IEEE80211_HW_REPORTS_LOW_ACK,
2328 IEEE80211_HW_SUPPORTS_TX_FRAG,
2329 IEEE80211_HW_SUPPORTS_TDLS_BUFFER_STA,
2330 IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP,
2331 IEEE80211_HW_DOESNT_SUPPORT_QOS_NDP,
2332 IEEE80211_HW_BUFF_MMPDU_TXQ,
2333 IEEE80211_HW_SUPPORTS_VHT_EXT_NSS_BW,
2334 IEEE80211_HW_STA_MMPDU_TXQ,
2335 IEEE80211_HW_TX_STATUS_NO_AMPDU_LEN,
2336 IEEE80211_HW_SUPPORTS_MULTI_BSSID,
2337 IEEE80211_HW_SUPPORTS_ONLY_HE_MULTI_BSSID,
2338 IEEE80211_HW_AMPDU_KEYBORDER_SUPPORT,
2339
2340 /* keep last, obviously */
2341 NUM_IEEE80211_HW_FLAGS
2342};
2343
2344/**
2345 * struct ieee80211_hw - hardware information and state
2346 *
2347 * This structure contains the configuration and hardware
2348 * information for an 802.11 PHY.
2349 *
2350 * @wiphy: This points to the &struct wiphy allocated for this
2351 * 802.11 PHY. You must fill in the @perm_addr and @dev
2352 * members of this structure using SET_IEEE80211_DEV()
2353 * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
2354 * bands (with channels, bitrates) are registered here.
2355 *
2356 * @conf: &struct ieee80211_conf, device configuration, don't use.
2357 *
2358 * @priv: pointer to private area that was allocated for driver use
2359 * along with this structure.
2360 *
2361 * @flags: hardware flags, see &enum ieee80211_hw_flags.
2362 *
2363 * @extra_tx_headroom: headroom to reserve in each transmit skb
2364 * for use by the driver (e.g. for transmit headers.)
2365 *
2366 * @extra_beacon_tailroom: tailroom to reserve in each beacon tx skb.
2367 * Can be used by drivers to add extra IEs.
2368 *
2369 * @max_signal: Maximum value for signal (rssi) in RX information, used
2370 * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
2371 *
2372 * @max_listen_interval: max listen interval in units of beacon interval
2373 * that HW supports
2374 *
2375 * @queues: number of available hardware transmit queues for
2376 * data packets. WMM/QoS requires at least four, these
2377 * queues need to have configurable access parameters.
2378 *
2379 * @rate_control_algorithm: rate control algorithm for this hardware.
2380 * If unset (NULL), the default algorithm will be used. Must be
2381 * set before calling ieee80211_register_hw().
2382 *
2383 * @vif_data_size: size (in bytes) of the drv_priv data area
2384 * within &struct ieee80211_vif.
2385 * @sta_data_size: size (in bytes) of the drv_priv data area
2386 * within &struct ieee80211_sta.
2387 * @chanctx_data_size: size (in bytes) of the drv_priv data area
2388 * within &struct ieee80211_chanctx_conf.
2389 * @txq_data_size: size (in bytes) of the drv_priv data area
2390 * within @struct ieee80211_txq.
2391 *
2392 * @max_rates: maximum number of alternate rate retry stages the hw
2393 * can handle.
2394 * @max_report_rates: maximum number of alternate rate retry stages
2395 * the hw can report back.
2396 * @max_rate_tries: maximum number of tries for each stage
2397 *
2398 * @max_rx_aggregation_subframes: maximum buffer size (number of
2399 * sub-frames) to be used for A-MPDU block ack receiver
2400 * aggregation.
2401 * This is only relevant if the device has restrictions on the
2402 * number of subframes, if it relies on mac80211 to do reordering
2403 * it shouldn't be set.
2404 *
2405 * @max_tx_aggregation_subframes: maximum number of subframes in an
2406 * aggregate an HT/HE device will transmit. In HT AddBA we'll
2407 * advertise a constant value of 64 as some older APs crash if
2408 * the window size is smaller (an example is LinkSys WRT120N
2409 * with FW v1.0.07 build 002 Jun 18 2012).
2410 * For AddBA to HE capable peers this value will be used.
2411 *
2412 * @max_tx_fragments: maximum number of tx buffers per (A)-MSDU, sum
2413 * of 1 + skb_shinfo(skb)->nr_frags for each skb in the frag_list.
2414 *
2415 * @offchannel_tx_hw_queue: HW queue ID to use for offchannel TX
2416 * (if %IEEE80211_HW_QUEUE_CONTROL is set)
2417 *
2418 * @radiotap_mcs_details: lists which MCS information can the HW
2419 * reports, by default it is set to _MCS, _GI and _BW but doesn't
2420 * include _FMT. Use %IEEE80211_RADIOTAP_MCS_HAVE_\* values, only
2421 * adding _BW is supported today.
2422 *
2423 * @radiotap_vht_details: lists which VHT MCS information the HW reports,
2424 * the default is _GI | _BANDWIDTH.
2425 * Use the %IEEE80211_RADIOTAP_VHT_KNOWN_\* values.
2426 *
2427 * @radiotap_he: HE radiotap validity flags
2428 *
2429 * @radiotap_timestamp: Information for the radiotap timestamp field; if the
2430 * @units_pos member is set to a non-negative value then the timestamp
2431 * field will be added and populated from the &struct ieee80211_rx_status
2432 * device_timestamp.
2433 * @radiotap_timestamp.units_pos: Must be set to a combination of a
2434 * IEEE80211_RADIOTAP_TIMESTAMP_UNIT_* and a
2435 * IEEE80211_RADIOTAP_TIMESTAMP_SPOS_* value.
2436 * @radiotap_timestamp.accuracy: If non-negative, fills the accuracy in the
2437 * radiotap field and the accuracy known flag will be set.
2438 *
2439 * @netdev_features: netdev features to be set in each netdev created
2440 * from this HW. Note that not all features are usable with mac80211,
2441 * other features will be rejected during HW registration.
2442 *
2443 * @uapsd_queues: This bitmap is included in (re)association frame to indicate
2444 * for each access category if it is uAPSD trigger-enabled and delivery-
2445 * enabled. Use IEEE80211_WMM_IE_STA_QOSINFO_AC_* to set this bitmap.
2446 * Each bit corresponds to different AC. Value '1' in specific bit means
2447 * that corresponding AC is both trigger- and delivery-enabled. '0' means
2448 * neither enabled.
2449 *
2450 * @uapsd_max_sp_len: maximum number of total buffered frames the WMM AP may
2451 * deliver to a WMM STA during any Service Period triggered by the WMM STA.
2452 * Use IEEE80211_WMM_IE_STA_QOSINFO_SP_* for correct values.
2453 *
2454 * @n_cipher_schemes: a size of an array of cipher schemes definitions.
2455 * @cipher_schemes: a pointer to an array of cipher scheme definitions
2456 * supported by HW.
2457 * @max_nan_de_entries: maximum number of NAN DE functions supported by the
2458 * device.
2459 *
2460 * @tx_sk_pacing_shift: Pacing shift to set on TCP sockets when frames from
2461 * them are encountered. The default should typically not be changed,
2462 * unless the driver has good reasons for needing more buffers.
2463 *
2464 * @weight_multiplier: Driver specific airtime weight multiplier used while
2465 * refilling deficit of each TXQ.
2466 *
2467 * @max_mtu: the max mtu could be set.
2468 */
2469struct ieee80211_hw {
2470 struct ieee80211_conf conf;
2471 struct wiphy *wiphy;
2472 const char *rate_control_algorithm;
2473 void *priv;
2474 unsigned long flags[BITS_TO_LONGS(NUM_IEEE80211_HW_FLAGS)];
2475 unsigned int extra_tx_headroom;
2476 unsigned int extra_beacon_tailroom;
2477 int vif_data_size;
2478 int sta_data_size;
2479 int chanctx_data_size;
2480 int txq_data_size;
2481 u16 queues;
2482 u16 max_listen_interval;
2483 s8 max_signal;
2484 u8 max_rates;
2485 u8 max_report_rates;
2486 u8 max_rate_tries;
2487 u16 max_rx_aggregation_subframes;
2488 u16 max_tx_aggregation_subframes;
2489 u8 max_tx_fragments;
2490 u8 offchannel_tx_hw_queue;
2491 u8 radiotap_mcs_details;
2492 u16 radiotap_vht_details;
2493 struct {
2494 int units_pos;
2495 s16 accuracy;
2496 } radiotap_timestamp;
2497 netdev_features_t netdev_features;
2498 u8 uapsd_queues;
2499 u8 uapsd_max_sp_len;
2500 u8 n_cipher_schemes;
2501 const struct ieee80211_cipher_scheme *cipher_schemes;
2502 u8 max_nan_de_entries;
2503 u8 tx_sk_pacing_shift;
2504 u8 weight_multiplier;
2505 u32 max_mtu;
2506};
2507
2508static inline bool _ieee80211_hw_check(struct ieee80211_hw *hw,
2509 enum ieee80211_hw_flags flg)
2510{
2511 return test_bit(flg, hw->flags);
2512}
2513#define ieee80211_hw_check(hw, flg) _ieee80211_hw_check(hw, IEEE80211_HW_##flg)
2514
2515static inline void _ieee80211_hw_set(struct ieee80211_hw *hw,
2516 enum ieee80211_hw_flags flg)
2517{
2518 return __set_bit(flg, hw->flags);
2519}
2520#define ieee80211_hw_set(hw, flg) _ieee80211_hw_set(hw, IEEE80211_HW_##flg)
2521
2522/**
2523 * struct ieee80211_scan_request - hw scan request
2524 *
2525 * @ies: pointers different parts of IEs (in req.ie)
2526 * @req: cfg80211 request.
2527 */
2528struct ieee80211_scan_request {
2529 struct ieee80211_scan_ies ies;
2530
2531 /* Keep last */
2532 struct cfg80211_scan_request req;
2533};
2534
2535/**
2536 * struct ieee80211_tdls_ch_sw_params - TDLS channel switch parameters
2537 *
2538 * @sta: peer this TDLS channel-switch request/response came from
2539 * @chandef: channel referenced in a TDLS channel-switch request
2540 * @action_code: see &enum ieee80211_tdls_actioncode
2541 * @status: channel-switch response status
2542 * @timestamp: time at which the frame was received
2543 * @switch_time: switch-timing parameter received in the frame
2544 * @switch_timeout: switch-timing parameter received in the frame
2545 * @tmpl_skb: TDLS switch-channel response template
2546 * @ch_sw_tm_ie: offset of the channel-switch timing IE inside @tmpl_skb
2547 */
2548struct ieee80211_tdls_ch_sw_params {
2549 struct ieee80211_sta *sta;
2550 struct cfg80211_chan_def *chandef;
2551 u8 action_code;
2552 u32 status;
2553 u32 timestamp;
2554 u16 switch_time;
2555 u16 switch_timeout;
2556 struct sk_buff *tmpl_skb;
2557 u32 ch_sw_tm_ie;
2558};
2559
2560/**
2561 * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy
2562 *
2563 * @wiphy: the &struct wiphy which we want to query
2564 *
2565 * mac80211 drivers can use this to get to their respective
2566 * &struct ieee80211_hw. Drivers wishing to get to their own private
2567 * structure can then access it via hw->priv. Note that mac802111 drivers should
2568 * not use wiphy_priv() to try to get their private driver structure as this
2569 * is already used internally by mac80211.
2570 *
2571 * Return: The mac80211 driver hw struct of @wiphy.
2572 */
2573struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy);
2574
2575/**
2576 * SET_IEEE80211_DEV - set device for 802.11 hardware
2577 *
2578 * @hw: the &struct ieee80211_hw to set the device for
2579 * @dev: the &struct device of this 802.11 device
2580 */
2581static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev)
2582{
2583 set_wiphy_dev(hw->wiphy, dev);
2584}
2585
2586/**
2587 * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware
2588 *
2589 * @hw: the &struct ieee80211_hw to set the MAC address for
2590 * @addr: the address to set
2591 */
2592static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, const u8 *addr)
2593{
2594 memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
2595}
2596
2597static inline struct ieee80211_rate *
2598ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
2599 const struct ieee80211_tx_info *c)
2600{
2601 if (WARN_ON_ONCE(c->control.rates[0].idx < 0))
2602 return NULL;
2603 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx];
2604}
2605
2606static inline struct ieee80211_rate *
2607ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw,
2608 const struct ieee80211_tx_info *c)
2609{
2610 if (c->control.rts_cts_rate_idx < 0)
2611 return NULL;
2612 return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx];
2613}
2614
2615static inline struct ieee80211_rate *
2616ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
2617 const struct ieee80211_tx_info *c, int idx)
2618{
2619 if (c->control.rates[idx + 1].idx < 0)
2620 return NULL;
2621 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx];
2622}
2623
2624/**
2625 * ieee80211_free_txskb - free TX skb
2626 * @hw: the hardware
2627 * @skb: the skb
2628 *
2629 * Free a transmit skb. Use this funtion when some failure
2630 * to transmit happened and thus status cannot be reported.
2631 */
2632void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb);
2633
2634/**
2635 * DOC: Hardware crypto acceleration
2636 *
2637 * mac80211 is capable of taking advantage of many hardware
2638 * acceleration designs for encryption and decryption operations.
2639 *
2640 * The set_key() callback in the &struct ieee80211_ops for a given
2641 * device is called to enable hardware acceleration of encryption and
2642 * decryption. The callback takes a @sta parameter that will be NULL
2643 * for default keys or keys used for transmission only, or point to
2644 * the station information for the peer for individual keys.
2645 * Multiple transmission keys with the same key index may be used when
2646 * VLANs are configured for an access point.
2647 *
2648 * When transmitting, the TX control data will use the @hw_key_idx
2649 * selected by the driver by modifying the &struct ieee80211_key_conf
2650 * pointed to by the @key parameter to the set_key() function.
2651 *
2652 * The set_key() call for the %SET_KEY command should return 0 if
2653 * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be
2654 * added; if you return 0 then hw_key_idx must be assigned to the
2655 * hardware key index, you are free to use the full u8 range.
2656 *
2657 * Note that in the case that the @IEEE80211_HW_SW_CRYPTO_CONTROL flag is
2658 * set, mac80211 will not automatically fall back to software crypto if
2659 * enabling hardware crypto failed. The set_key() call may also return the
2660 * value 1 to permit this specific key/algorithm to be done in software.
2661 *
2662 * When the cmd is %DISABLE_KEY then it must succeed.
2663 *
2664 * Note that it is permissible to not decrypt a frame even if a key
2665 * for it has been uploaded to hardware, the stack will not make any
2666 * decision based on whether a key has been uploaded or not but rather
2667 * based on the receive flags.
2668 *
2669 * The &struct ieee80211_key_conf structure pointed to by the @key
2670 * parameter is guaranteed to be valid until another call to set_key()
2671 * removes it, but it can only be used as a cookie to differentiate
2672 * keys.
2673 *
2674 * In TKIP some HW need to be provided a phase 1 key, for RX decryption
2675 * acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key
2676 * handler.
2677 * The update_tkip_key() call updates the driver with the new phase 1 key.
2678 * This happens every time the iv16 wraps around (every 65536 packets). The
2679 * set_key() call will happen only once for each key (unless the AP did
2680 * rekeying), it will not include a valid phase 1 key. The valid phase 1 key is
2681 * provided by update_tkip_key only. The trigger that makes mac80211 call this
2682 * handler is software decryption with wrap around of iv16.
2683 *
2684 * The set_default_unicast_key() call updates the default WEP key index
2685 * configured to the hardware for WEP encryption type. This is required
2686 * for devices that support offload of data packets (e.g. ARP responses).
2687 *
2688 * Mac80211 drivers should set the @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 flag
2689 * when they are able to replace in-use PTK keys according to to following
2690 * requirements:
2691 * 1) They do not hand over frames decrypted with the old key to
2692 mac80211 once the call to set_key() with command %DISABLE_KEY has been
2693 completed when also setting @IEEE80211_KEY_FLAG_GENERATE_IV for any key,
2694 2) either drop or continue to use the old key for any outgoing frames queued
2695 at the time of the key deletion (including re-transmits),
2696 3) never send out a frame queued prior to the set_key() %SET_KEY command
2697 encrypted with the new key and
2698 4) never send out a frame unencrypted when it should be encrypted.
2699 Mac80211 will not queue any new frames for a deleted key to the driver.
2700 */
2701
2702/**
2703 * DOC: Powersave support
2704 *
2705 * mac80211 has support for various powersave implementations.
2706 *
2707 * First, it can support hardware that handles all powersaving by itself,
2708 * such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS hardware
2709 * flag. In that case, it will be told about the desired powersave mode
2710 * with the %IEEE80211_CONF_PS flag depending on the association status.
2711 * The hardware must take care of sending nullfunc frames when necessary,
2712 * i.e. when entering and leaving powersave mode. The hardware is required
2713 * to look at the AID in beacons and signal to the AP that it woke up when
2714 * it finds traffic directed to it.
2715 *
2716 * %IEEE80211_CONF_PS flag enabled means that the powersave mode defined in
2717 * IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused
2718 * with hardware wakeup and sleep states. Driver is responsible for waking
2719 * up the hardware before issuing commands to the hardware and putting it
2720 * back to sleep at appropriate times.
2721 *
2722 * When PS is enabled, hardware needs to wakeup for beacons and receive the
2723 * buffered multicast/broadcast frames after the beacon. Also it must be
2724 * possible to send frames and receive the acknowledment frame.
2725 *
2726 * Other hardware designs cannot send nullfunc frames by themselves and also
2727 * need software support for parsing the TIM bitmap. This is also supported
2728 * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and
2729 * %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still
2730 * required to pass up beacons. The hardware is still required to handle
2731 * waking up for multicast traffic; if it cannot the driver must handle that
2732 * as best as it can, mac80211 is too slow to do that.
2733 *
2734 * Dynamic powersave is an extension to normal powersave in which the
2735 * hardware stays awake for a user-specified period of time after sending a
2736 * frame so that reply frames need not be buffered and therefore delayed to
2737 * the next wakeup. It's compromise of getting good enough latency when
2738 * there's data traffic and still saving significantly power in idle
2739 * periods.
2740 *
2741 * Dynamic powersave is simply supported by mac80211 enabling and disabling
2742 * PS based on traffic. Driver needs to only set %IEEE80211_HW_SUPPORTS_PS
2743 * flag and mac80211 will handle everything automatically. Additionally,
2744 * hardware having support for the dynamic PS feature may set the
2745 * %IEEE80211_HW_SUPPORTS_DYNAMIC_PS flag to indicate that it can support
2746 * dynamic PS mode itself. The driver needs to look at the
2747 * @dynamic_ps_timeout hardware configuration value and use it that value
2748 * whenever %IEEE80211_CONF_PS is set. In this case mac80211 will disable
2749 * dynamic PS feature in stack and will just keep %IEEE80211_CONF_PS
2750 * enabled whenever user has enabled powersave.
2751 *
2752 * Driver informs U-APSD client support by enabling
2753 * %IEEE80211_VIF_SUPPORTS_UAPSD flag. The mode is configured through the
2754 * uapsd parameter in conf_tx() operation. Hardware needs to send the QoS
2755 * Nullfunc frames and stay awake until the service period has ended. To
2756 * utilize U-APSD, dynamic powersave is disabled for voip AC and all frames
2757 * from that AC are transmitted with powersave enabled.
2758 *
2759 * Note: U-APSD client mode is not yet supported with
2760 * %IEEE80211_HW_PS_NULLFUNC_STACK.
2761 */
2762
2763/**
2764 * DOC: Beacon filter support
2765 *
2766 * Some hardware have beacon filter support to reduce host cpu wakeups
2767 * which will reduce system power consumption. It usually works so that
2768 * the firmware creates a checksum of the beacon but omits all constantly
2769 * changing elements (TSF, TIM etc). Whenever the checksum changes the
2770 * beacon is forwarded to the host, otherwise it will be just dropped. That
2771 * way the host will only receive beacons where some relevant information
2772 * (for example ERP protection or WMM settings) have changed.
2773 *
2774 * Beacon filter support is advertised with the %IEEE80211_VIF_BEACON_FILTER
2775 * interface capability. The driver needs to enable beacon filter support
2776 * whenever power save is enabled, that is %IEEE80211_CONF_PS is set. When
2777 * power save is enabled, the stack will not check for beacon loss and the
2778 * driver needs to notify about loss of beacons with ieee80211_beacon_loss().
2779 *
2780 * The time (or number of beacons missed) until the firmware notifies the
2781 * driver of a beacon loss event (which in turn causes the driver to call
2782 * ieee80211_beacon_loss()) should be configurable and will be controlled
2783 * by mac80211 and the roaming algorithm in the future.
2784 *
2785 * Since there may be constantly changing information elements that nothing
2786 * in the software stack cares about, we will, in the future, have mac80211
2787 * tell the driver which information elements are interesting in the sense
2788 * that we want to see changes in them. This will include
2789 *
2790 * - a list of information element IDs
2791 * - a list of OUIs for the vendor information element
2792 *
2793 * Ideally, the hardware would filter out any beacons without changes in the
2794 * requested elements, but if it cannot support that it may, at the expense
2795 * of some efficiency, filter out only a subset. For example, if the device
2796 * doesn't support checking for OUIs it should pass up all changes in all
2797 * vendor information elements.
2798 *
2799 * Note that change, for the sake of simplification, also includes information
2800 * elements appearing or disappearing from the beacon.
2801 *
2802 * Some hardware supports an "ignore list" instead, just make sure nothing
2803 * that was requested is on the ignore list, and include commonly changing
2804 * information element IDs in the ignore list, for example 11 (BSS load) and
2805 * the various vendor-assigned IEs with unknown contents (128, 129, 133-136,
2806 * 149, 150, 155, 156, 173, 176, 178, 179, 219); for forward compatibility
2807 * it could also include some currently unused IDs.
2808 *
2809 *
2810 * In addition to these capabilities, hardware should support notifying the
2811 * host of changes in the beacon RSSI. This is relevant to implement roaming
2812 * when no traffic is flowing (when traffic is flowing we see the RSSI of
2813 * the received data packets). This can consist in notifying the host when
2814 * the RSSI changes significantly or when it drops below or rises above
2815 * configurable thresholds. In the future these thresholds will also be
2816 * configured by mac80211 (which gets them from userspace) to implement
2817 * them as the roaming algorithm requires.
2818 *
2819 * If the hardware cannot implement this, the driver should ask it to
2820 * periodically pass beacon frames to the host so that software can do the
2821 * signal strength threshold checking.
2822 */
2823
2824/**
2825 * DOC: Spatial multiplexing power save
2826 *
2827 * SMPS (Spatial multiplexing power save) is a mechanism to conserve
2828 * power in an 802.11n implementation. For details on the mechanism
2829 * and rationale, please refer to 802.11 (as amended by 802.11n-2009)
2830 * "11.2.3 SM power save".
2831 *
2832 * The mac80211 implementation is capable of sending action frames
2833 * to update the AP about the station's SMPS mode, and will instruct
2834 * the driver to enter the specific mode. It will also announce the
2835 * requested SMPS mode during the association handshake. Hardware
2836 * support for this feature is required, and can be indicated by
2837 * hardware flags.
2838 *
2839 * The default mode will be "automatic", which nl80211/cfg80211
2840 * defines to be dynamic SMPS in (regular) powersave, and SMPS
2841 * turned off otherwise.
2842 *
2843 * To support this feature, the driver must set the appropriate
2844 * hardware support flags, and handle the SMPS flag to the config()
2845 * operation. It will then with this mechanism be instructed to
2846 * enter the requested SMPS mode while associated to an HT AP.
2847 */
2848
2849/**
2850 * DOC: Frame filtering
2851 *
2852 * mac80211 requires to see many management frames for proper
2853 * operation, and users may want to see many more frames when
2854 * in monitor mode. However, for best CPU usage and power consumption,
2855 * having as few frames as possible percolate through the stack is
2856 * desirable. Hence, the hardware should filter as much as possible.
2857 *
2858 * To achieve this, mac80211 uses filter flags (see below) to tell
2859 * the driver's configure_filter() function which frames should be
2860 * passed to mac80211 and which should be filtered out.
2861 *
2862 * Before configure_filter() is invoked, the prepare_multicast()
2863 * callback is invoked with the parameters @mc_count and @mc_list
2864 * for the combined multicast address list of all virtual interfaces.
2865 * It's use is optional, and it returns a u64 that is passed to
2866 * configure_filter(). Additionally, configure_filter() has the
2867 * arguments @changed_flags telling which flags were changed and
2868 * @total_flags with the new flag states.
2869 *
2870 * If your device has no multicast address filters your driver will
2871 * need to check both the %FIF_ALLMULTI flag and the @mc_count
2872 * parameter to see whether multicast frames should be accepted
2873 * or dropped.
2874 *
2875 * All unsupported flags in @total_flags must be cleared.
2876 * Hardware does not support a flag if it is incapable of _passing_
2877 * the frame to the stack. Otherwise the driver must ignore
2878 * the flag, but not clear it.
2879 * You must _only_ clear the flag (announce no support for the
2880 * flag to mac80211) if you are not able to pass the packet type
2881 * to the stack (so the hardware always filters it).
2882 * So for example, you should clear @FIF_CONTROL, if your hardware
2883 * always filters control frames. If your hardware always passes
2884 * control frames to the kernel and is incapable of filtering them,
2885 * you do _not_ clear the @FIF_CONTROL flag.
2886 * This rule applies to all other FIF flags as well.
2887 */
2888
2889/**
2890 * DOC: AP support for powersaving clients
2891 *
2892 * In order to implement AP and P2P GO modes, mac80211 has support for
2893 * client powersaving, both "legacy" PS (PS-Poll/null data) and uAPSD.
2894 * There currently is no support for sAPSD.
2895 *
2896 * There is one assumption that mac80211 makes, namely that a client
2897 * will not poll with PS-Poll and trigger with uAPSD at the same time.
2898 * Both are supported, and both can be used by the same client, but
2899 * they can't be used concurrently by the same client. This simplifies
2900 * the driver code.
2901 *
2902 * The first thing to keep in mind is that there is a flag for complete
2903 * driver implementation: %IEEE80211_HW_AP_LINK_PS. If this flag is set,
2904 * mac80211 expects the driver to handle most of the state machine for
2905 * powersaving clients and will ignore the PM bit in incoming frames.
2906 * Drivers then use ieee80211_sta_ps_transition() to inform mac80211 of
2907 * stations' powersave transitions. In this mode, mac80211 also doesn't
2908 * handle PS-Poll/uAPSD.
2909 *
2910 * In the mode without %IEEE80211_HW_AP_LINK_PS, mac80211 will check the
2911 * PM bit in incoming frames for client powersave transitions. When a
2912 * station goes to sleep, we will stop transmitting to it. There is,
2913 * however, a race condition: a station might go to sleep while there is
2914 * data buffered on hardware queues. If the device has support for this
2915 * it will reject frames, and the driver should give the frames back to
2916 * mac80211 with the %IEEE80211_TX_STAT_TX_FILTERED flag set which will
2917 * cause mac80211 to retry the frame when the station wakes up. The
2918 * driver is also notified of powersave transitions by calling its
2919 * @sta_notify callback.
2920 *
2921 * When the station is asleep, it has three choices: it can wake up,
2922 * it can PS-Poll, or it can possibly start a uAPSD service period.
2923 * Waking up is implemented by simply transmitting all buffered (and
2924 * filtered) frames to the station. This is the easiest case. When
2925 * the station sends a PS-Poll or a uAPSD trigger frame, mac80211
2926 * will inform the driver of this with the @allow_buffered_frames
2927 * callback; this callback is optional. mac80211 will then transmit
2928 * the frames as usual and set the %IEEE80211_TX_CTL_NO_PS_BUFFER
2929 * on each frame. The last frame in the service period (or the only
2930 * response to a PS-Poll) also has %IEEE80211_TX_STATUS_EOSP set to
2931 * indicate that it ends the service period; as this frame must have
2932 * TX status report it also sets %IEEE80211_TX_CTL_REQ_TX_STATUS.
2933 * When TX status is reported for this frame, the service period is
2934 * marked has having ended and a new one can be started by the peer.
2935 *
2936 * Additionally, non-bufferable MMPDUs can also be transmitted by
2937 * mac80211 with the %IEEE80211_TX_CTL_NO_PS_BUFFER set in them.
2938 *
2939 * Another race condition can happen on some devices like iwlwifi
2940 * when there are frames queued for the station and it wakes up
2941 * or polls; the frames that are already queued could end up being
2942 * transmitted first instead, causing reordering and/or wrong
2943 * processing of the EOSP. The cause is that allowing frames to be
2944 * transmitted to a certain station is out-of-band communication to
2945 * the device. To allow this problem to be solved, the driver can
2946 * call ieee80211_sta_block_awake() if frames are buffered when it
2947 * is notified that the station went to sleep. When all these frames
2948 * have been filtered (see above), it must call the function again
2949 * to indicate that the station is no longer blocked.
2950 *
2951 * If the driver buffers frames in the driver for aggregation in any
2952 * way, it must use the ieee80211_sta_set_buffered() call when it is
2953 * notified of the station going to sleep to inform mac80211 of any
2954 * TIDs that have frames buffered. Note that when a station wakes up
2955 * this information is reset (hence the requirement to call it when
2956 * informed of the station going to sleep). Then, when a service
2957 * period starts for any reason, @release_buffered_frames is called
2958 * with the number of frames to be released and which TIDs they are
2959 * to come from. In this case, the driver is responsible for setting
2960 * the EOSP (for uAPSD) and MORE_DATA bits in the released frames,
2961 * to help the @more_data parameter is passed to tell the driver if
2962 * there is more data on other TIDs -- the TIDs to release frames
2963 * from are ignored since mac80211 doesn't know how many frames the
2964 * buffers for those TIDs contain.
2965 *
2966 * If the driver also implement GO mode, where absence periods may
2967 * shorten service periods (or abort PS-Poll responses), it must
2968 * filter those response frames except in the case of frames that
2969 * are buffered in the driver -- those must remain buffered to avoid
2970 * reordering. Because it is possible that no frames are released
2971 * in this case, the driver must call ieee80211_sta_eosp()
2972 * to indicate to mac80211 that the service period ended anyway.
2973 *
2974 * Finally, if frames from multiple TIDs are released from mac80211
2975 * but the driver might reorder them, it must clear & set the flags
2976 * appropriately (only the last frame may have %IEEE80211_TX_STATUS_EOSP)
2977 * and also take care of the EOSP and MORE_DATA bits in the frame.
2978 * The driver may also use ieee80211_sta_eosp() in this case.
2979 *
2980 * Note that if the driver ever buffers frames other than QoS-data
2981 * frames, it must take care to never send a non-QoS-data frame as
2982 * the last frame in a service period, adding a QoS-nulldata frame
2983 * after a non-QoS-data frame if needed.
2984 */
2985
2986/**
2987 * DOC: HW queue control
2988 *
2989 * Before HW queue control was introduced, mac80211 only had a single static
2990 * assignment of per-interface AC software queues to hardware queues. This
2991 * was problematic for a few reasons:
2992 * 1) off-channel transmissions might get stuck behind other frames
2993 * 2) multiple virtual interfaces couldn't be handled correctly
2994 * 3) after-DTIM frames could get stuck behind other frames
2995 *
2996 * To solve this, hardware typically uses multiple different queues for all
2997 * the different usages, and this needs to be propagated into mac80211 so it
2998 * won't have the same problem with the software queues.
2999 *
3000 * Therefore, mac80211 now offers the %IEEE80211_HW_QUEUE_CONTROL capability
3001 * flag that tells it that the driver implements its own queue control. To do
3002 * so, the driver will set up the various queues in each &struct ieee80211_vif
3003 * and the offchannel queue in &struct ieee80211_hw. In response, mac80211 will
3004 * use those queue IDs in the hw_queue field of &struct ieee80211_tx_info and
3005 * if necessary will queue the frame on the right software queue that mirrors
3006 * the hardware queue.
3007 * Additionally, the driver has to then use these HW queue IDs for the queue
3008 * management functions (ieee80211_stop_queue() et al.)
3009 *
3010 * The driver is free to set up the queue mappings as needed, multiple virtual
3011 * interfaces may map to the same hardware queues if needed. The setup has to
3012 * happen during add_interface or change_interface callbacks. For example, a
3013 * driver supporting station+station and station+AP modes might decide to have
3014 * 10 hardware queues to handle different scenarios:
3015 *
3016 * 4 AC HW queues for 1st vif: 0, 1, 2, 3
3017 * 4 AC HW queues for 2nd vif: 4, 5, 6, 7
3018 * after-DTIM queue for AP: 8
3019 * off-channel queue: 9
3020 *
3021 * It would then set up the hardware like this:
3022 * hw.offchannel_tx_hw_queue = 9
3023 *
3024 * and the first virtual interface that is added as follows:
3025 * vif.hw_queue[IEEE80211_AC_VO] = 0
3026 * vif.hw_queue[IEEE80211_AC_VI] = 1
3027 * vif.hw_queue[IEEE80211_AC_BE] = 2
3028 * vif.hw_queue[IEEE80211_AC_BK] = 3
3029 * vif.cab_queue = 8 // if AP mode, otherwise %IEEE80211_INVAL_HW_QUEUE
3030 * and the second virtual interface with 4-7.
3031 *
3032 * If queue 6 gets full, for example, mac80211 would only stop the second
3033 * virtual interface's BE queue since virtual interface queues are per AC.
3034 *
3035 * Note that the vif.cab_queue value should be set to %IEEE80211_INVAL_HW_QUEUE
3036 * whenever the queue is not used (i.e. the interface is not in AP mode) if the
3037 * queue could potentially be shared since mac80211 will look at cab_queue when
3038 * a queue is stopped/woken even if the interface is not in AP mode.
3039 */
3040
3041/**
3042 * enum ieee80211_filter_flags - hardware filter flags
3043 *
3044 * These flags determine what the filter in hardware should be
3045 * programmed to let through and what should not be passed to the
3046 * stack. It is always safe to pass more frames than requested,
3047 * but this has negative impact on power consumption.
3048 *
3049 * @FIF_ALLMULTI: pass all multicast frames, this is used if requested
3050 * by the user or if the hardware is not capable of filtering by
3051 * multicast address.
3052 *
3053 * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the
3054 * %RX_FLAG_FAILED_FCS_CRC for them)
3055 *
3056 * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set
3057 * the %RX_FLAG_FAILED_PLCP_CRC for them
3058 *
3059 * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate
3060 * to the hardware that it should not filter beacons or probe responses
3061 * by BSSID. Filtering them can greatly reduce the amount of processing
3062 * mac80211 needs to do and the amount of CPU wakeups, so you should
3063 * honour this flag if possible.
3064 *
3065 * @FIF_CONTROL: pass control frames (except for PS Poll) addressed to this
3066 * station
3067 *
3068 * @FIF_OTHER_BSS: pass frames destined to other BSSes
3069 *
3070 * @FIF_PSPOLL: pass PS Poll frames
3071 *
3072 * @FIF_PROBE_REQ: pass probe request frames
3073 */
3074enum ieee80211_filter_flags {
3075 FIF_ALLMULTI = 1<<1,
3076 FIF_FCSFAIL = 1<<2,
3077 FIF_PLCPFAIL = 1<<3,
3078 FIF_BCN_PRBRESP_PROMISC = 1<<4,
3079 FIF_CONTROL = 1<<5,
3080 FIF_OTHER_BSS = 1<<6,
3081 FIF_PSPOLL = 1<<7,
3082 FIF_PROBE_REQ = 1<<8,
3083};
3084
3085/**
3086 * enum ieee80211_ampdu_mlme_action - A-MPDU actions
3087 *
3088 * These flags are used with the ampdu_action() callback in
3089 * &struct ieee80211_ops to indicate which action is needed.
3090 *
3091 * Note that drivers MUST be able to deal with a TX aggregation
3092 * session being stopped even before they OK'ed starting it by
3093 * calling ieee80211_start_tx_ba_cb_irqsafe, because the peer
3094 * might receive the addBA frame and send a delBA right away!
3095 *
3096 * @IEEE80211_AMPDU_RX_START: start RX aggregation
3097 * @IEEE80211_AMPDU_RX_STOP: stop RX aggregation
3098 * @IEEE80211_AMPDU_TX_START: start TX aggregation
3099 * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational
3100 * @IEEE80211_AMPDU_TX_STOP_CONT: stop TX aggregation but continue transmitting
3101 * queued packets, now unaggregated. After all packets are transmitted the
3102 * driver has to call ieee80211_stop_tx_ba_cb_irqsafe().
3103 * @IEEE80211_AMPDU_TX_STOP_FLUSH: stop TX aggregation and flush all packets,
3104 * called when the station is removed. There's no need or reason to call
3105 * ieee80211_stop_tx_ba_cb_irqsafe() in this case as mac80211 assumes the
3106 * session is gone and removes the station.
3107 * @IEEE80211_AMPDU_TX_STOP_FLUSH_CONT: called when TX aggregation is stopped
3108 * but the driver hasn't called ieee80211_stop_tx_ba_cb_irqsafe() yet and
3109 * now the connection is dropped and the station will be removed. Drivers
3110 * should clean up and drop remaining packets when this is called.
3111 */
3112enum ieee80211_ampdu_mlme_action {
3113 IEEE80211_AMPDU_RX_START,
3114 IEEE80211_AMPDU_RX_STOP,
3115 IEEE80211_AMPDU_TX_START,
3116 IEEE80211_AMPDU_TX_STOP_CONT,
3117 IEEE80211_AMPDU_TX_STOP_FLUSH,
3118 IEEE80211_AMPDU_TX_STOP_FLUSH_CONT,
3119 IEEE80211_AMPDU_TX_OPERATIONAL,
3120};
3121
3122/**
3123 * struct ieee80211_ampdu_params - AMPDU action parameters
3124 *
3125 * @action: the ampdu action, value from %ieee80211_ampdu_mlme_action.
3126 * @sta: peer of this AMPDU session
3127 * @tid: tid of the BA session
3128 * @ssn: start sequence number of the session. TX/RX_STOP can pass 0. When
3129 * action is set to %IEEE80211_AMPDU_RX_START the driver passes back the
3130 * actual ssn value used to start the session and writes the value here.
3131 * @buf_size: reorder buffer size (number of subframes). Valid only when the
3132 * action is set to %IEEE80211_AMPDU_RX_START or
3133 * %IEEE80211_AMPDU_TX_OPERATIONAL
3134 * @amsdu: indicates the peer's ability to receive A-MSDU within A-MPDU.
3135 * valid when the action is set to %IEEE80211_AMPDU_TX_OPERATIONAL
3136 * @timeout: BA session timeout. Valid only when the action is set to
3137 * %IEEE80211_AMPDU_RX_START
3138 */
3139struct ieee80211_ampdu_params {
3140 enum ieee80211_ampdu_mlme_action action;
3141 struct ieee80211_sta *sta;
3142 u16 tid;
3143 u16 ssn;
3144 u16 buf_size;
3145 bool amsdu;
3146 u16 timeout;
3147};
3148
3149/**
3150 * enum ieee80211_frame_release_type - frame release reason
3151 * @IEEE80211_FRAME_RELEASE_PSPOLL: frame released for PS-Poll
3152 * @IEEE80211_FRAME_RELEASE_UAPSD: frame(s) released due to
3153 * frame received on trigger-enabled AC
3154 */
3155enum ieee80211_frame_release_type {
3156 IEEE80211_FRAME_RELEASE_PSPOLL,
3157 IEEE80211_FRAME_RELEASE_UAPSD,
3158};
3159
3160/**
3161 * enum ieee80211_rate_control_changed - flags to indicate what changed
3162 *
3163 * @IEEE80211_RC_BW_CHANGED: The bandwidth that can be used to transmit
3164 * to this station changed. The actual bandwidth is in the station
3165 * information -- for HT20/40 the IEEE80211_HT_CAP_SUP_WIDTH_20_40
3166 * flag changes, for HT and VHT the bandwidth field changes.
3167 * @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed.
3168 * @IEEE80211_RC_SUPP_RATES_CHANGED: The supported rate set of this peer
3169 * changed (in IBSS mode) due to discovering more information about
3170 * the peer.
3171 * @IEEE80211_RC_NSS_CHANGED: N_SS (number of spatial streams) was changed
3172 * by the peer
3173 */
3174enum ieee80211_rate_control_changed {
3175 IEEE80211_RC_BW_CHANGED = BIT(0),
3176 IEEE80211_RC_SMPS_CHANGED = BIT(1),
3177 IEEE80211_RC_SUPP_RATES_CHANGED = BIT(2),
3178 IEEE80211_RC_NSS_CHANGED = BIT(3),
3179};
3180
3181/**
3182 * enum ieee80211_roc_type - remain on channel type
3183 *
3184 * With the support for multi channel contexts and multi channel operations,
3185 * remain on channel operations might be limited/deferred/aborted by other
3186 * flows/operations which have higher priority (and vise versa).
3187 * Specifying the ROC type can be used by devices to prioritize the ROC
3188 * operations compared to other operations/flows.
3189 *
3190 * @IEEE80211_ROC_TYPE_NORMAL: There are no special requirements for this ROC.
3191 * @IEEE80211_ROC_TYPE_MGMT_TX: The remain on channel request is required
3192 * for sending managment frames offchannel.
3193 */
3194enum ieee80211_roc_type {
3195 IEEE80211_ROC_TYPE_NORMAL = 0,
3196 IEEE80211_ROC_TYPE_MGMT_TX,
3197};
3198
3199/**
3200 * enum ieee80211_reconfig_complete_type - reconfig type
3201 *
3202 * This enum is used by the reconfig_complete() callback to indicate what
3203 * reconfiguration type was completed.
3204 *
3205 * @IEEE80211_RECONFIG_TYPE_RESTART: hw restart type
3206 * (also due to resume() callback returning 1)
3207 * @IEEE80211_RECONFIG_TYPE_SUSPEND: suspend type (regardless
3208 * of wowlan configuration)
3209 */
3210enum ieee80211_reconfig_type {
3211 IEEE80211_RECONFIG_TYPE_RESTART,
3212 IEEE80211_RECONFIG_TYPE_SUSPEND,
3213};
3214
3215/**
3216 * struct ieee80211_ops - callbacks from mac80211 to the driver
3217 *
3218 * This structure contains various callbacks that the driver may
3219 * handle or, in some cases, must handle, for example to configure
3220 * the hardware to a new channel or to transmit a frame.
3221 *
3222 * @tx: Handler that 802.11 module calls for each transmitted frame.
3223 * skb contains the buffer starting from the IEEE 802.11 header.
3224 * The low-level driver should send the frame out based on
3225 * configuration in the TX control data. This handler should,
3226 * preferably, never fail and stop queues appropriately.
3227 * Must be atomic.
3228 *
3229 * @start: Called before the first netdevice attached to the hardware
3230 * is enabled. This should turn on the hardware and must turn on
3231 * frame reception (for possibly enabled monitor interfaces.)
3232 * Returns negative error codes, these may be seen in userspace,
3233 * or zero.
3234 * When the device is started it should not have a MAC address
3235 * to avoid acknowledging frames before a non-monitor device
3236 * is added.
3237 * Must be implemented and can sleep.
3238 *
3239 * @stop: Called after last netdevice attached to the hardware
3240 * is disabled. This should turn off the hardware (at least
3241 * it must turn off frame reception.)
3242 * May be called right after add_interface if that rejects
3243 * an interface. If you added any work onto the mac80211 workqueue
3244 * you should ensure to cancel it on this callback.
3245 * Must be implemented and can sleep.
3246 *
3247 * @suspend: Suspend the device; mac80211 itself will quiesce before and
3248 * stop transmitting and doing any other configuration, and then
3249 * ask the device to suspend. This is only invoked when WoWLAN is
3250 * configured, otherwise the device is deconfigured completely and
3251 * reconfigured at resume time.
3252 * The driver may also impose special conditions under which it
3253 * wants to use the "normal" suspend (deconfigure), say if it only
3254 * supports WoWLAN when the device is associated. In this case, it
3255 * must return 1 from this function.
3256 *
3257 * @resume: If WoWLAN was configured, this indicates that mac80211 is
3258 * now resuming its operation, after this the device must be fully
3259 * functional again. If this returns an error, the only way out is
3260 * to also unregister the device. If it returns 1, then mac80211
3261 * will also go through the regular complete restart on resume.
3262 *
3263 * @set_wakeup: Enable or disable wakeup when WoWLAN configuration is
3264 * modified. The reason is that device_set_wakeup_enable() is
3265 * supposed to be called when the configuration changes, not only
3266 * in suspend().
3267 *
3268 * @add_interface: Called when a netdevice attached to the hardware is
3269 * enabled. Because it is not called for monitor mode devices, @start
3270 * and @stop must be implemented.
3271 * The driver should perform any initialization it needs before
3272 * the device can be enabled. The initial configuration for the
3273 * interface is given in the conf parameter.
3274 * The callback may refuse to add an interface by returning a
3275 * negative error code (which will be seen in userspace.)
3276 * Must be implemented and can sleep.
3277 *
3278 * @change_interface: Called when a netdevice changes type. This callback
3279 * is optional, but only if it is supported can interface types be
3280 * switched while the interface is UP. The callback may sleep.
3281 * Note that while an interface is being switched, it will not be
3282 * found by the interface iteration callbacks.
3283 *
3284 * @remove_interface: Notifies a driver that an interface is going down.
3285 * The @stop callback is called after this if it is the last interface
3286 * and no monitor interfaces are present.
3287 * When all interfaces are removed, the MAC address in the hardware
3288 * must be cleared so the device no longer acknowledges packets,
3289 * the mac_addr member of the conf structure is, however, set to the
3290 * MAC address of the device going away.
3291 * Hence, this callback must be implemented. It can sleep.
3292 *
3293 * @config: Handler for configuration requests. IEEE 802.11 code calls this
3294 * function to change hardware configuration, e.g., channel.
3295 * This function should never fail but returns a negative error code
3296 * if it does. The callback can sleep.
3297 *
3298 * @bss_info_changed: Handler for configuration requests related to BSS
3299 * parameters that may vary during BSS's lifespan, and may affect low
3300 * level driver (e.g. assoc/disassoc status, erp parameters).
3301 * This function should not be used if no BSS has been set, unless
3302 * for association indication. The @changed parameter indicates which
3303 * of the bss parameters has changed when a call is made. The callback
3304 * can sleep.
3305 *
3306 * @prepare_multicast: Prepare for multicast filter configuration.
3307 * This callback is optional, and its return value is passed
3308 * to configure_filter(). This callback must be atomic.
3309 *
3310 * @configure_filter: Configure the device's RX filter.
3311 * See the section "Frame filtering" for more information.
3312 * This callback must be implemented and can sleep.
3313 *
3314 * @config_iface_filter: Configure the interface's RX filter.
3315 * This callback is optional and is used to configure which frames
3316 * should be passed to mac80211. The filter_flags is the combination
3317 * of FIF_* flags. The changed_flags is a bit mask that indicates
3318 * which flags are changed.
3319 * This callback can sleep.
3320 *
3321 * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit
3322 * must be set or cleared for a given STA. Must be atomic.
3323 *
3324 * @set_key: See the section "Hardware crypto acceleration"
3325 * This callback is only called between add_interface and
3326 * remove_interface calls, i.e. while the given virtual interface
3327 * is enabled.
3328 * Returns a negative error code if the key can't be added.
3329 * The callback can sleep.
3330 *
3331 * @update_tkip_key: See the section "Hardware crypto acceleration"
3332 * This callback will be called in the context of Rx. Called for drivers
3333 * which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY.
3334 * The callback must be atomic.
3335 *
3336 * @set_rekey_data: If the device supports GTK rekeying, for example while the
3337 * host is suspended, it can assign this callback to retrieve the data
3338 * necessary to do GTK rekeying, this is the KEK, KCK and replay counter.
3339 * After rekeying was done it should (for example during resume) notify
3340 * userspace of the new replay counter using ieee80211_gtk_rekey_notify().
3341 *
3342 * @set_default_unicast_key: Set the default (unicast) key index, useful for
3343 * WEP when the device sends data packets autonomously, e.g. for ARP
3344 * offloading. The index can be 0-3, or -1 for unsetting it.
3345 *
3346 * @hw_scan: Ask the hardware to service the scan request, no need to start
3347 * the scan state machine in stack. The scan must honour the channel
3348 * configuration done by the regulatory agent in the wiphy's
3349 * registered bands. The hardware (or the driver) needs to make sure
3350 * that power save is disabled.
3351 * The @req ie/ie_len members are rewritten by mac80211 to contain the
3352 * entire IEs after the SSID, so that drivers need not look at these
3353 * at all but just send them after the SSID -- mac80211 includes the
3354 * (extended) supported rates and HT information (where applicable).
3355 * When the scan finishes, ieee80211_scan_completed() must be called;
3356 * note that it also must be called when the scan cannot finish due to
3357 * any error unless this callback returned a negative error code.
3358 * This callback is also allowed to return the special return value 1,
3359 * this indicates that hardware scan isn't desirable right now and a
3360 * software scan should be done instead. A driver wishing to use this
3361 * capability must ensure its (hardware) scan capabilities aren't
3362 * advertised as more capable than mac80211's software scan is.
3363 * The callback can sleep.
3364 *
3365 * @cancel_hw_scan: Ask the low-level tp cancel the active hw scan.
3366 * The driver should ask the hardware to cancel the scan (if possible),
3367 * but the scan will be completed only after the driver will call
3368 * ieee80211_scan_completed().
3369 * This callback is needed for wowlan, to prevent enqueueing a new
3370 * scan_work after the low-level driver was already suspended.
3371 * The callback can sleep.
3372 *
3373 * @sched_scan_start: Ask the hardware to start scanning repeatedly at
3374 * specific intervals. The driver must call the
3375 * ieee80211_sched_scan_results() function whenever it finds results.
3376 * This process will continue until sched_scan_stop is called.
3377 *
3378 * @sched_scan_stop: Tell the hardware to stop an ongoing scheduled scan.
3379 * In this case, ieee80211_sched_scan_stopped() must not be called.
3380 *
3381 * @sw_scan_start: Notifier function that is called just before a software scan
3382 * is started. Can be NULL, if the driver doesn't need this notification.
3383 * The mac_addr parameter allows supporting NL80211_SCAN_FLAG_RANDOM_ADDR,
3384 * the driver may set the NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR flag if it
3385 * can use this parameter. The callback can sleep.
3386 *
3387 * @sw_scan_complete: Notifier function that is called just after a
3388 * software scan finished. Can be NULL, if the driver doesn't need
3389 * this notification.
3390 * The callback can sleep.
3391 *
3392 * @get_stats: Return low-level statistics.
3393 * Returns zero if statistics are available.
3394 * The callback can sleep.
3395 *
3396 * @get_key_seq: If your device implements encryption in hardware and does
3397 * IV/PN assignment then this callback should be provided to read the
3398 * IV/PN for the given key from hardware.
3399 * The callback must be atomic.
3400 *
3401 * @set_frag_threshold: Configuration of fragmentation threshold. Assign this
3402 * if the device does fragmentation by itself. Note that to prevent the
3403 * stack from doing fragmentation IEEE80211_HW_SUPPORTS_TX_FRAG
3404 * should be set as well.
3405 * The callback can sleep.
3406 *
3407 * @set_rts_threshold: Configuration of RTS threshold (if device needs it)
3408 * The callback can sleep.
3409 *
3410 * @sta_add: Notifies low level driver about addition of an associated station,
3411 * AP, IBSS/WDS/mesh peer etc. This callback can sleep.
3412 *
3413 * @sta_remove: Notifies low level driver about removal of an associated
3414 * station, AP, IBSS/WDS/mesh peer etc. Note that after the callback
3415 * returns it isn't safe to use the pointer, not even RCU protected;
3416 * no RCU grace period is guaranteed between returning here and freeing
3417 * the station. See @sta_pre_rcu_remove if needed.
3418 * This callback can sleep.
3419 *
3420 * @sta_add_debugfs: Drivers can use this callback to add debugfs files
3421 * when a station is added to mac80211's station list. This callback
3422 * should be within a CONFIG_MAC80211_DEBUGFS conditional. This
3423 * callback can sleep.
3424 *
3425 * @sta_notify: Notifies low level driver about power state transition of an
3426 * associated station, AP, IBSS/WDS/mesh peer etc. For a VIF operating
3427 * in AP mode, this callback will not be called when the flag
3428 * %IEEE80211_HW_AP_LINK_PS is set. Must be atomic.
3429 *
3430 * @sta_state: Notifies low level driver about state transition of a
3431 * station (which can be the AP, a client, IBSS/WDS/mesh peer etc.)
3432 * This callback is mutually exclusive with @sta_add/@sta_remove.
3433 * It must not fail for down transitions but may fail for transitions
3434 * up the list of states. Also note that after the callback returns it
3435 * isn't safe to use the pointer, not even RCU protected - no RCU grace
3436 * period is guaranteed between returning here and freeing the station.
3437 * See @sta_pre_rcu_remove if needed.
3438 * The callback can sleep.
3439 *
3440 * @sta_pre_rcu_remove: Notify driver about station removal before RCU
3441 * synchronisation. This is useful if a driver needs to have station
3442 * pointers protected using RCU, it can then use this call to clear
3443 * the pointers instead of waiting for an RCU grace period to elapse
3444 * in @sta_state.
3445 * The callback can sleep.
3446 *
3447 * @sta_rc_update: Notifies the driver of changes to the bitrates that can be
3448 * used to transmit to the station. The changes are advertised with bits
3449 * from &enum ieee80211_rate_control_changed and the values are reflected
3450 * in the station data. This callback should only be used when the driver
3451 * uses hardware rate control (%IEEE80211_HW_HAS_RATE_CONTROL) since
3452 * otherwise the rate control algorithm is notified directly.
3453 * Must be atomic.
3454 * @sta_rate_tbl_update: Notifies the driver that the rate table changed. This
3455 * is only used if the configured rate control algorithm actually uses
3456 * the new rate table API, and is therefore optional. Must be atomic.
3457 *
3458 * @sta_statistics: Get statistics for this station. For example with beacon
3459 * filtering, the statistics kept by mac80211 might not be accurate, so
3460 * let the driver pre-fill the statistics. The driver can fill most of
3461 * the values (indicating which by setting the filled bitmap), but not
3462 * all of them make sense - see the source for which ones are possible.
3463 * Statistics that the driver doesn't fill will be filled by mac80211.
3464 * The callback can sleep.
3465 *
3466 * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
3467 * bursting) for a hardware TX queue.
3468 * Returns a negative error code on failure.
3469 * The callback can sleep.
3470 *
3471 * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
3472 * this is only used for IBSS mode BSSID merging and debugging. Is not a
3473 * required function.
3474 * The callback can sleep.
3475 *
3476 * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
3477 * Currently, this is only used for IBSS mode debugging. Is not a
3478 * required function.
3479 * The callback can sleep.
3480 *
3481 * @offset_tsf: Offset the TSF timer by the specified value in the
3482 * firmware/hardware. Preferred to set_tsf as it avoids delay between
3483 * calling set_tsf() and hardware getting programmed, which will show up
3484 * as TSF delay. Is not a required function.
3485 * The callback can sleep.
3486 *
3487 * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize
3488 * with other STAs in the IBSS. This is only used in IBSS mode. This
3489 * function is optional if the firmware/hardware takes full care of
3490 * TSF synchronization.
3491 * The callback can sleep.
3492 *
3493 * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
3494 * This is needed only for IBSS mode and the result of this function is
3495 * used to determine whether to reply to Probe Requests.
3496 * Returns non-zero if this device sent the last beacon.
3497 * The callback can sleep.
3498 *
3499 * @get_survey: Return per-channel survey information
3500 *
3501 * @rfkill_poll: Poll rfkill hardware state. If you need this, you also
3502 * need to set wiphy->rfkill_poll to %true before registration,
3503 * and need to call wiphy_rfkill_set_hw_state() in the callback.
3504 * The callback can sleep.
3505 *
3506 * @set_coverage_class: Set slot time for given coverage class as specified
3507 * in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout
3508 * accordingly; coverage class equals to -1 to enable ACK timeout
3509 * estimation algorithm (dynack). To disable dynack set valid value for
3510 * coverage class. This callback is not required and may sleep.
3511 *
3512 * @testmode_cmd: Implement a cfg80211 test mode command. The passed @vif may
3513 * be %NULL. The callback can sleep.
3514 * @testmode_dump: Implement a cfg80211 test mode dump. The callback can sleep.
3515 *
3516 * @flush: Flush all pending frames from the hardware queue, making sure
3517 * that the hardware queues are empty. The @queues parameter is a bitmap
3518 * of queues to flush, which is useful if different virtual interfaces
3519 * use different hardware queues; it may also indicate all queues.
3520 * If the parameter @drop is set to %true, pending frames may be dropped.
3521 * Note that vif can be NULL.
3522 * The callback can sleep.
3523 *
3524 * @channel_switch: Drivers that need (or want) to offload the channel
3525 * switch operation for CSAs received from the AP may implement this
3526 * callback. They must then call ieee80211_chswitch_done() to indicate
3527 * completion of the channel switch.
3528 *
3529 * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device.
3530 * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may
3531 * reject TX/RX mask combinations they cannot support by returning -EINVAL
3532 * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX).
3533 *
3534 * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant).
3535 *
3536 * @remain_on_channel: Starts an off-channel period on the given channel, must
3537 * call back to ieee80211_ready_on_channel() when on that channel. Note
3538 * that normal channel traffic is not stopped as this is intended for hw
3539 * offload. Frames to transmit on the off-channel channel are transmitted
3540 * normally except for the %IEEE80211_TX_CTL_TX_OFFCHAN flag. When the
3541 * duration (which will always be non-zero) expires, the driver must call
3542 * ieee80211_remain_on_channel_expired().
3543 * Note that this callback may be called while the device is in IDLE and
3544 * must be accepted in this case.
3545 * This callback may sleep.
3546 * @cancel_remain_on_channel: Requests that an ongoing off-channel period is
3547 * aborted before it expires. This callback may sleep.
3548 *
3549 * @set_ringparam: Set tx and rx ring sizes.
3550 *
3551 * @get_ringparam: Get tx and rx ring current and maximum sizes.
3552 *
3553 * @tx_frames_pending: Check if there is any pending frame in the hardware
3554 * queues before entering power save.
3555 *
3556 * @set_bitrate_mask: Set a mask of rates to be used for rate control selection
3557 * when transmitting a frame. Currently only legacy rates are handled.
3558 * The callback can sleep.
3559 * @event_callback: Notify driver about any event in mac80211. See
3560 * &enum ieee80211_event_type for the different types.
3561 * The callback must be atomic.
3562 *
3563 * @release_buffered_frames: Release buffered frames according to the given
3564 * parameters. In the case where the driver buffers some frames for
3565 * sleeping stations mac80211 will use this callback to tell the driver
3566 * to release some frames, either for PS-poll or uAPSD.
3567 * Note that if the @more_data parameter is %false the driver must check
3568 * if there are more frames on the given TIDs, and if there are more than
3569 * the frames being released then it must still set the more-data bit in
3570 * the frame. If the @more_data parameter is %true, then of course the
3571 * more-data bit must always be set.
3572 * The @tids parameter tells the driver which TIDs to release frames
3573 * from, for PS-poll it will always have only a single bit set.
3574 * In the case this is used for a PS-poll initiated release, the
3575 * @num_frames parameter will always be 1 so code can be shared. In
3576 * this case the driver must also set %IEEE80211_TX_STATUS_EOSP flag
3577 * on the TX status (and must report TX status) so that the PS-poll
3578 * period is properly ended. This is used to avoid sending multiple
3579 * responses for a retried PS-poll frame.
3580 * In the case this is used for uAPSD, the @num_frames parameter may be
3581 * bigger than one, but the driver may send fewer frames (it must send
3582 * at least one, however). In this case it is also responsible for
3583 * setting the EOSP flag in the QoS header of the frames. Also, when the
3584 * service period ends, the driver must set %IEEE80211_TX_STATUS_EOSP
3585 * on the last frame in the SP. Alternatively, it may call the function
3586 * ieee80211_sta_eosp() to inform mac80211 of the end of the SP.
3587 * This callback must be atomic.
3588 * @allow_buffered_frames: Prepare device to allow the given number of frames
3589 * to go out to the given station. The frames will be sent by mac80211
3590 * via the usual TX path after this call. The TX information for frames
3591 * released will also have the %IEEE80211_TX_CTL_NO_PS_BUFFER flag set
3592 * and the last one will also have %IEEE80211_TX_STATUS_EOSP set. In case
3593 * frames from multiple TIDs are released and the driver might reorder
3594 * them between the TIDs, it must set the %IEEE80211_TX_STATUS_EOSP flag
3595 * on the last frame and clear it on all others and also handle the EOSP
3596 * bit in the QoS header correctly. Alternatively, it can also call the
3597 * ieee80211_sta_eosp() function.
3598 * The @tids parameter is a bitmap and tells the driver which TIDs the
3599 * frames will be on; it will at most have two bits set.
3600 * This callback must be atomic.
3601 *
3602 * @get_et_sset_count: Ethtool API to get string-set count.
3603 *
3604 * @get_et_stats: Ethtool API to get a set of u64 stats.
3605 *
3606 * @get_et_strings: Ethtool API to get a set of strings to describe stats
3607 * and perhaps other supported types of ethtool data-sets.
3608 *
3609 * @mgd_prepare_tx: Prepare for transmitting a management frame for association
3610 * before associated. In multi-channel scenarios, a virtual interface is
3611 * bound to a channel before it is associated, but as it isn't associated
3612 * yet it need not necessarily be given airtime, in particular since any
3613 * transmission to a P2P GO needs to be synchronized against the GO's
3614 * powersave state. mac80211 will call this function before transmitting a
3615 * management frame prior to having successfully associated to allow the
3616 * driver to give it channel time for the transmission, to get a response
3617 * and to be able to synchronize with the GO.
3618 * For drivers that set %IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP, mac80211
3619 * would also call this function before transmitting a deauthentication
3620 * frame in case that no beacon was heard from the AP/P2P GO.
3621 * The callback will be called before each transmission and upon return
3622 * mac80211 will transmit the frame right away.
3623 * If duration is greater than zero, mac80211 hints to the driver the
3624 * duration for which the operation is requested.
3625 * The callback is optional and can (should!) sleep.
3626 *
3627 * @mgd_protect_tdls_discover: Protect a TDLS discovery session. After sending
3628 * a TDLS discovery-request, we expect a reply to arrive on the AP's
3629 * channel. We must stay on the channel (no PSM, scan, etc.), since a TDLS
3630 * setup-response is a direct packet not buffered by the AP.
3631 * mac80211 will call this function just before the transmission of a TDLS
3632 * discovery-request. The recommended period of protection is at least
3633 * 2 * (DTIM period).
3634 * The callback is optional and can sleep.
3635 *
3636 * @add_chanctx: Notifies device driver about new channel context creation.
3637 * This callback may sleep.
3638 * @remove_chanctx: Notifies device driver about channel context destruction.
3639 * This callback may sleep.
3640 * @change_chanctx: Notifies device driver about channel context changes that
3641 * may happen when combining different virtual interfaces on the same
3642 * channel context with different settings
3643 * This callback may sleep.
3644 * @assign_vif_chanctx: Notifies device driver about channel context being bound
3645 * to vif. Possible use is for hw queue remapping.
3646 * This callback may sleep.
3647 * @unassign_vif_chanctx: Notifies device driver about channel context being
3648 * unbound from vif.
3649 * This callback may sleep.
3650 * @switch_vif_chanctx: switch a number of vifs from one chanctx to
3651 * another, as specified in the list of
3652 * @ieee80211_vif_chanctx_switch passed to the driver, according
3653 * to the mode defined in &ieee80211_chanctx_switch_mode.
3654 * This callback may sleep.
3655 *
3656 * @start_ap: Start operation on the AP interface, this is called after all the
3657 * information in bss_conf is set and beacon can be retrieved. A channel
3658 * context is bound before this is called. Note that if the driver uses
3659 * software scan or ROC, this (and @stop_ap) isn't called when the AP is
3660 * just "paused" for scanning/ROC, which is indicated by the beacon being
3661 * disabled/enabled via @bss_info_changed.
3662 * @stop_ap: Stop operation on the AP interface.
3663 *
3664 * @reconfig_complete: Called after a call to ieee80211_restart_hw() and
3665 * during resume, when the reconfiguration has completed.
3666 * This can help the driver implement the reconfiguration step (and
3667 * indicate mac80211 is ready to receive frames).
3668 * This callback may sleep.
3669 *
3670 * @ipv6_addr_change: IPv6 address assignment on the given interface changed.
3671 * Currently, this is only called for managed or P2P client interfaces.
3672 * This callback is optional; it must not sleep.
3673 *
3674 * @channel_switch_beacon: Starts a channel switch to a new channel.
3675 * Beacons are modified to include CSA or ECSA IEs before calling this
3676 * function. The corresponding count fields in these IEs must be
3677 * decremented, and when they reach 1 the driver must call
3678 * ieee80211_csa_finish(). Drivers which use ieee80211_beacon_get()
3679 * get the csa counter decremented by mac80211, but must check if it is
3680 * 1 using ieee80211_csa_is_complete() after the beacon has been
3681 * transmitted and then call ieee80211_csa_finish().
3682 * If the CSA count starts as zero or 1, this function will not be called,
3683 * since there won't be any time to beacon before the switch anyway.
3684 * @pre_channel_switch: This is an optional callback that is called
3685 * before a channel switch procedure is started (ie. when a STA
3686 * gets a CSA or a userspace initiated channel-switch), allowing
3687 * the driver to prepare for the channel switch.
3688 * @post_channel_switch: This is an optional callback that is called
3689 * after a channel switch procedure is completed, allowing the
3690 * driver to go back to a normal configuration.
3691 * @abort_channel_switch: This is an optional callback that is called
3692 * when channel switch procedure was completed, allowing the
3693 * driver to go back to a normal configuration.
3694 * @channel_switch_rx_beacon: This is an optional callback that is called
3695 * when channel switch procedure is in progress and additional beacon with
3696 * CSA IE was received, allowing driver to track changes in count.
3697 * @join_ibss: Join an IBSS (on an IBSS interface); this is called after all
3698 * information in bss_conf is set up and the beacon can be retrieved. A
3699 * channel context is bound before this is called.
3700 * @leave_ibss: Leave the IBSS again.
3701 *
3702 * @get_expected_throughput: extract the expected throughput towards the
3703 * specified station. The returned value is expressed in Kbps. It returns 0
3704 * if the RC algorithm does not have proper data to provide.
3705 *
3706 * @get_txpower: get current maximum tx power (in dBm) based on configuration
3707 * and hardware limits.
3708 *
3709 * @tdls_channel_switch: Start channel-switching with a TDLS peer. The driver
3710 * is responsible for continually initiating channel-switching operations
3711 * and returning to the base channel for communication with the AP. The
3712 * driver receives a channel-switch request template and the location of
3713 * the switch-timing IE within the template as part of the invocation.
3714 * The template is valid only within the call, and the driver can
3715 * optionally copy the skb for further re-use.
3716 * @tdls_cancel_channel_switch: Stop channel-switching with a TDLS peer. Both
3717 * peers must be on the base channel when the call completes.
3718 * @tdls_recv_channel_switch: a TDLS channel-switch related frame (request or
3719 * response) has been received from a remote peer. The driver gets
3720 * parameters parsed from the incoming frame and may use them to continue
3721 * an ongoing channel-switch operation. In addition, a channel-switch
3722 * response template is provided, together with the location of the
3723 * switch-timing IE within the template. The skb can only be used within
3724 * the function call.
3725 *
3726 * @wake_tx_queue: Called when new packets have been added to the queue.
3727 * @sync_rx_queues: Process all pending frames in RSS queues. This is a
3728 * synchronization which is needed in case driver has in its RSS queues
3729 * pending frames that were received prior to the control path action
3730 * currently taken (e.g. disassociation) but are not processed yet.
3731 *
3732 * @start_nan: join an existing NAN cluster, or create a new one.
3733 * @stop_nan: leave the NAN cluster.
3734 * @nan_change_conf: change NAN configuration. The data in cfg80211_nan_conf
3735 * contains full new configuration and changes specify which parameters
3736 * are changed with respect to the last NAN config.
3737 * The driver gets both full configuration and the changed parameters since
3738 * some devices may need the full configuration while others need only the
3739 * changed parameters.
3740 * @add_nan_func: Add a NAN function. Returns 0 on success. The data in
3741 * cfg80211_nan_func must not be referenced outside the scope of
3742 * this call.
3743 * @del_nan_func: Remove a NAN function. The driver must call
3744 * ieee80211_nan_func_terminated() with
3745 * NL80211_NAN_FUNC_TERM_REASON_USER_REQUEST reason code upon removal.
3746 * @can_aggregate_in_amsdu: Called in order to determine if HW supports
3747 * aggregating two specific frames in the same A-MSDU. The relation
3748 * between the skbs should be symmetric and transitive. Note that while
3749 * skb is always a real frame, head may or may not be an A-MSDU.
3750 * @get_ftm_responder_stats: Retrieve FTM responder statistics, if available.
3751 * Statistics should be cumulative, currently no way to reset is provided.
3752 *
3753 * @start_pmsr: start peer measurement (e.g. FTM) (this call can sleep)
3754 * @abort_pmsr: abort peer measurement (this call can sleep)
3755 */
3756struct ieee80211_ops {
3757 void (*tx)(struct ieee80211_hw *hw,
3758 struct ieee80211_tx_control *control,
3759 struct sk_buff *skb);
3760 int (*start)(struct ieee80211_hw *hw);
3761 void (*stop)(struct ieee80211_hw *hw);
3762#ifdef CONFIG_PM
3763 int (*suspend)(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan);
3764 int (*resume)(struct ieee80211_hw *hw);
3765 void (*set_wakeup)(struct ieee80211_hw *hw, bool enabled);
3766#endif
3767 int (*add_interface)(struct ieee80211_hw *hw,
3768 struct ieee80211_vif *vif);
3769 int (*change_interface)(struct ieee80211_hw *hw,
3770 struct ieee80211_vif *vif,
3771 enum nl80211_iftype new_type, bool p2p);
3772 void (*remove_interface)(struct ieee80211_hw *hw,
3773 struct ieee80211_vif *vif);
3774 int (*config)(struct ieee80211_hw *hw, u32 changed);
3775 void (*bss_info_changed)(struct ieee80211_hw *hw,
3776 struct ieee80211_vif *vif,
3777 struct ieee80211_bss_conf *info,
3778 u32 changed);
3779
3780 int (*start_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
3781 void (*stop_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
3782
3783 u64 (*prepare_multicast)(struct ieee80211_hw *hw,
3784 struct netdev_hw_addr_list *mc_list);
3785 void (*configure_filter)(struct ieee80211_hw *hw,
3786 unsigned int changed_flags,
3787 unsigned int *total_flags,
3788 u64 multicast);
3789 void (*config_iface_filter)(struct ieee80211_hw *hw,
3790 struct ieee80211_vif *vif,
3791 unsigned int filter_flags,
3792 unsigned int changed_flags);
3793 int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
3794 bool set);
3795 int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd,
3796 struct ieee80211_vif *vif, struct ieee80211_sta *sta,
3797 struct ieee80211_key_conf *key);
3798 void (*update_tkip_key)(struct ieee80211_hw *hw,
3799 struct ieee80211_vif *vif,
3800 struct ieee80211_key_conf *conf,
3801 struct ieee80211_sta *sta,
3802 u32 iv32, u16 *phase1key);
3803 void (*set_rekey_data)(struct ieee80211_hw *hw,
3804 struct ieee80211_vif *vif,
3805 struct cfg80211_gtk_rekey_data *data);
3806 void (*set_default_unicast_key)(struct ieee80211_hw *hw,
3807 struct ieee80211_vif *vif, int idx);
3808 int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3809 struct ieee80211_scan_request *req);
3810 void (*cancel_hw_scan)(struct ieee80211_hw *hw,
3811 struct ieee80211_vif *vif);
3812 int (*sched_scan_start)(struct ieee80211_hw *hw,
3813 struct ieee80211_vif *vif,
3814 struct cfg80211_sched_scan_request *req,
3815 struct ieee80211_scan_ies *ies);
3816 int (*sched_scan_stop)(struct ieee80211_hw *hw,
3817 struct ieee80211_vif *vif);
3818 void (*sw_scan_start)(struct ieee80211_hw *hw,
3819 struct ieee80211_vif *vif,
3820 const u8 *mac_addr);
3821 void (*sw_scan_complete)(struct ieee80211_hw *hw,
3822 struct ieee80211_vif *vif);
3823 int (*get_stats)(struct ieee80211_hw *hw,
3824 struct ieee80211_low_level_stats *stats);
3825 void (*get_key_seq)(struct ieee80211_hw *hw,
3826 struct ieee80211_key_conf *key,
3827 struct ieee80211_key_seq *seq);
3828 int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);
3829 int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
3830 int (*sta_add)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3831 struct ieee80211_sta *sta);
3832 int (*sta_remove)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3833 struct ieee80211_sta *sta);
3834#ifdef CONFIG_MAC80211_DEBUGFS
3835 void (*sta_add_debugfs)(struct ieee80211_hw *hw,
3836 struct ieee80211_vif *vif,
3837 struct ieee80211_sta *sta,
3838 struct dentry *dir);
3839#endif
3840 void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3841 enum sta_notify_cmd, struct ieee80211_sta *sta);
3842 int (*sta_set_txpwr)(struct ieee80211_hw *hw,
3843 struct ieee80211_vif *vif,
3844 struct ieee80211_sta *sta);
3845 int (*sta_state)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3846 struct ieee80211_sta *sta,
3847 enum ieee80211_sta_state old_state,
3848 enum ieee80211_sta_state new_state);
3849 void (*sta_pre_rcu_remove)(struct ieee80211_hw *hw,
3850 struct ieee80211_vif *vif,
3851 struct ieee80211_sta *sta);
3852 void (*sta_rc_update)(struct ieee80211_hw *hw,
3853 struct ieee80211_vif *vif,
3854 struct ieee80211_sta *sta,
3855 u32 changed);
3856 void (*sta_rate_tbl_update)(struct ieee80211_hw *hw,
3857 struct ieee80211_vif *vif,
3858 struct ieee80211_sta *sta);
3859 void (*sta_statistics)(struct ieee80211_hw *hw,
3860 struct ieee80211_vif *vif,
3861 struct ieee80211_sta *sta,
3862 struct station_info *sinfo);
3863 int (*conf_tx)(struct ieee80211_hw *hw,
3864 struct ieee80211_vif *vif, u16 ac,
3865 const struct ieee80211_tx_queue_params *params);
3866 u64 (*get_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
3867 void (*set_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3868 u64 tsf);
3869 void (*offset_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3870 s64 offset);
3871 void (*reset_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
3872 int (*tx_last_beacon)(struct ieee80211_hw *hw);
3873
3874 /**
3875 * @ampdu_action:
3876 * Perform a certain A-MPDU action.
3877 * The RA/TID combination determines the destination and TID we want
3878 * the ampdu action to be performed for. The action is defined through
3879 * ieee80211_ampdu_mlme_action.
3880 * When the action is set to %IEEE80211_AMPDU_TX_OPERATIONAL the driver
3881 * may neither send aggregates containing more subframes than @buf_size
3882 * nor send aggregates in a way that lost frames would exceed the
3883 * buffer size. If just limiting the aggregate size, this would be
3884 * possible with a buf_size of 8:
3885 *
3886 * - ``TX: 1.....7``
3887 * - ``RX: 2....7`` (lost frame #1)
3888 * - ``TX: 8..1...``
3889 *
3890 * which is invalid since #1 was now re-transmitted well past the
3891 * buffer size of 8. Correct ways to retransmit #1 would be:
3892 *
3893 * - ``TX: 1 or``
3894 * - ``TX: 18 or``
3895 * - ``TX: 81``
3896 *
3897 * Even ``189`` would be wrong since 1 could be lost again.
3898 *
3899 * Returns a negative error code on failure.
3900 * The callback can sleep.
3901 */
3902 int (*ampdu_action)(struct ieee80211_hw *hw,
3903 struct ieee80211_vif *vif,
3904 struct ieee80211_ampdu_params *params);
3905 int (*get_survey)(struct ieee80211_hw *hw, int idx,
3906 struct survey_info *survey);
3907 void (*rfkill_poll)(struct ieee80211_hw *hw);
3908 void (*set_coverage_class)(struct ieee80211_hw *hw, s16 coverage_class);
3909#ifdef CONFIG_NL80211_TESTMODE
3910 int (*testmode_cmd)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3911 void *data, int len);
3912 int (*testmode_dump)(struct ieee80211_hw *hw, struct sk_buff *skb,
3913 struct netlink_callback *cb,
3914 void *data, int len);
3915#endif
3916 void (*flush)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3917 u32 queues, bool drop);
3918 void (*channel_switch)(struct ieee80211_hw *hw,
3919 struct ieee80211_vif *vif,
3920 struct ieee80211_channel_switch *ch_switch);
3921 int (*set_antenna)(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant);
3922 int (*get_antenna)(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant);
3923
3924 int (*remain_on_channel)(struct ieee80211_hw *hw,
3925 struct ieee80211_vif *vif,
3926 struct ieee80211_channel *chan,
3927 int duration,
3928 enum ieee80211_roc_type type);
3929 int (*cancel_remain_on_channel)(struct ieee80211_hw *hw,
3930 struct ieee80211_vif *vif);
3931 int (*set_ringparam)(struct ieee80211_hw *hw, u32 tx, u32 rx);
3932 void (*get_ringparam)(struct ieee80211_hw *hw,
3933 u32 *tx, u32 *tx_max, u32 *rx, u32 *rx_max);
3934 bool (*tx_frames_pending)(struct ieee80211_hw *hw);
3935 int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3936 const struct cfg80211_bitrate_mask *mask);
3937 void (*event_callback)(struct ieee80211_hw *hw,
3938 struct ieee80211_vif *vif,
3939 const struct ieee80211_event *event);
3940
3941 void (*allow_buffered_frames)(struct ieee80211_hw *hw,
3942 struct ieee80211_sta *sta,
3943 u16 tids, int num_frames,
3944 enum ieee80211_frame_release_type reason,
3945 bool more_data);
3946 void (*release_buffered_frames)(struct ieee80211_hw *hw,
3947 struct ieee80211_sta *sta,
3948 u16 tids, int num_frames,
3949 enum ieee80211_frame_release_type reason,
3950 bool more_data);
3951
3952 int (*get_et_sset_count)(struct ieee80211_hw *hw,
3953 struct ieee80211_vif *vif, int sset);
3954 void (*get_et_stats)(struct ieee80211_hw *hw,
3955 struct ieee80211_vif *vif,
3956 struct ethtool_stats *stats, u64 *data);
3957 void (*get_et_strings)(struct ieee80211_hw *hw,
3958 struct ieee80211_vif *vif,
3959 u32 sset, u8 *data);
3960
3961 void (*mgd_prepare_tx)(struct ieee80211_hw *hw,
3962 struct ieee80211_vif *vif,
3963 u16 duration);
3964
3965 void (*mgd_protect_tdls_discover)(struct ieee80211_hw *hw,
3966 struct ieee80211_vif *vif);
3967
3968 int (*add_chanctx)(struct ieee80211_hw *hw,
3969 struct ieee80211_chanctx_conf *ctx);
3970 void (*remove_chanctx)(struct ieee80211_hw *hw,
3971 struct ieee80211_chanctx_conf *ctx);
3972 void (*change_chanctx)(struct ieee80211_hw *hw,
3973 struct ieee80211_chanctx_conf *ctx,
3974 u32 changed);
3975 int (*assign_vif_chanctx)(struct ieee80211_hw *hw,
3976 struct ieee80211_vif *vif,
3977 struct ieee80211_chanctx_conf *ctx);
3978 void (*unassign_vif_chanctx)(struct ieee80211_hw *hw,
3979 struct ieee80211_vif *vif,
3980 struct ieee80211_chanctx_conf *ctx);
3981 int (*switch_vif_chanctx)(struct ieee80211_hw *hw,
3982 struct ieee80211_vif_chanctx_switch *vifs,
3983 int n_vifs,
3984 enum ieee80211_chanctx_switch_mode mode);
3985
3986 void (*reconfig_complete)(struct ieee80211_hw *hw,
3987 enum ieee80211_reconfig_type reconfig_type);
3988
3989#if IS_ENABLED(CONFIG_IPV6)
3990 void (*ipv6_addr_change)(struct ieee80211_hw *hw,
3991 struct ieee80211_vif *vif,
3992 struct inet6_dev *idev);
3993#endif
3994 void (*channel_switch_beacon)(struct ieee80211_hw *hw,
3995 struct ieee80211_vif *vif,
3996 struct cfg80211_chan_def *chandef);
3997 int (*pre_channel_switch)(struct ieee80211_hw *hw,
3998 struct ieee80211_vif *vif,
3999 struct ieee80211_channel_switch *ch_switch);
4000
4001 int (*post_channel_switch)(struct ieee80211_hw *hw,
4002 struct ieee80211_vif *vif);
4003 void (*abort_channel_switch)(struct ieee80211_hw *hw,
4004 struct ieee80211_vif *vif);
4005 void (*channel_switch_rx_beacon)(struct ieee80211_hw *hw,
4006 struct ieee80211_vif *vif,
4007 struct ieee80211_channel_switch *ch_switch);
4008
4009 int (*join_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
4010 void (*leave_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
4011 u32 (*get_expected_throughput)(struct ieee80211_hw *hw,
4012 struct ieee80211_sta *sta);
4013 int (*get_txpower)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4014 int *dbm);
4015
4016 int (*tdls_channel_switch)(struct ieee80211_hw *hw,
4017 struct ieee80211_vif *vif,
4018 struct ieee80211_sta *sta, u8 oper_class,
4019 struct cfg80211_chan_def *chandef,
4020 struct sk_buff *tmpl_skb, u32 ch_sw_tm_ie);
4021 void (*tdls_cancel_channel_switch)(struct ieee80211_hw *hw,
4022 struct ieee80211_vif *vif,
4023 struct ieee80211_sta *sta);
4024 void (*tdls_recv_channel_switch)(struct ieee80211_hw *hw,
4025 struct ieee80211_vif *vif,
4026 struct ieee80211_tdls_ch_sw_params *params);
4027
4028 void (*wake_tx_queue)(struct ieee80211_hw *hw,
4029 struct ieee80211_txq *txq);
4030 void (*sync_rx_queues)(struct ieee80211_hw *hw);
4031
4032 int (*start_nan)(struct ieee80211_hw *hw,
4033 struct ieee80211_vif *vif,
4034 struct cfg80211_nan_conf *conf);
4035 int (*stop_nan)(struct ieee80211_hw *hw,
4036 struct ieee80211_vif *vif);
4037 int (*nan_change_conf)(struct ieee80211_hw *hw,
4038 struct ieee80211_vif *vif,
4039 struct cfg80211_nan_conf *conf, u32 changes);
4040 int (*add_nan_func)(struct ieee80211_hw *hw,
4041 struct ieee80211_vif *vif,
4042 const struct cfg80211_nan_func *nan_func);
4043 void (*del_nan_func)(struct ieee80211_hw *hw,
4044 struct ieee80211_vif *vif,
4045 u8 instance_id);
4046 bool (*can_aggregate_in_amsdu)(struct ieee80211_hw *hw,
4047 struct sk_buff *head,
4048 struct sk_buff *skb);
4049 int (*get_ftm_responder_stats)(struct ieee80211_hw *hw,
4050 struct ieee80211_vif *vif,
4051 struct cfg80211_ftm_responder_stats *ftm_stats);
4052 int (*start_pmsr)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4053 struct cfg80211_pmsr_request *request);
4054 void (*abort_pmsr)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4055 struct cfg80211_pmsr_request *request);
4056};
4057
4058/**
4059 * ieee80211_alloc_hw_nm - Allocate a new hardware device
4060 *
4061 * This must be called once for each hardware device. The returned pointer
4062 * must be used to refer to this device when calling other functions.
4063 * mac80211 allocates a private data area for the driver pointed to by
4064 * @priv in &struct ieee80211_hw, the size of this area is given as
4065 * @priv_data_len.
4066 *
4067 * @priv_data_len: length of private data
4068 * @ops: callbacks for this device
4069 * @requested_name: Requested name for this device.
4070 * NULL is valid value, and means use the default naming (phy%d)
4071 *
4072 * Return: A pointer to the new hardware device, or %NULL on error.
4073 */
4074struct ieee80211_hw *ieee80211_alloc_hw_nm(size_t priv_data_len,
4075 const struct ieee80211_ops *ops,
4076 const char *requested_name);
4077
4078/**
4079 * ieee80211_alloc_hw - Allocate a new hardware device
4080 *
4081 * This must be called once for each hardware device. The returned pointer
4082 * must be used to refer to this device when calling other functions.
4083 * mac80211 allocates a private data area for the driver pointed to by
4084 * @priv in &struct ieee80211_hw, the size of this area is given as
4085 * @priv_data_len.
4086 *
4087 * @priv_data_len: length of private data
4088 * @ops: callbacks for this device
4089 *
4090 * Return: A pointer to the new hardware device, or %NULL on error.
4091 */
4092static inline
4093struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len,
4094 const struct ieee80211_ops *ops)
4095{
4096 return ieee80211_alloc_hw_nm(priv_data_len, ops, NULL);
4097}
4098
4099/**
4100 * ieee80211_register_hw - Register hardware device
4101 *
4102 * You must call this function before any other functions in
4103 * mac80211. Note that before a hardware can be registered, you
4104 * need to fill the contained wiphy's information.
4105 *
4106 * @hw: the device to register as returned by ieee80211_alloc_hw()
4107 *
4108 * Return: 0 on success. An error code otherwise.
4109 */
4110int ieee80211_register_hw(struct ieee80211_hw *hw);
4111
4112/**
4113 * struct ieee80211_tpt_blink - throughput blink description
4114 * @throughput: throughput in Kbit/sec
4115 * @blink_time: blink time in milliseconds
4116 * (full cycle, ie. one off + one on period)
4117 */
4118struct ieee80211_tpt_blink {
4119 int throughput;
4120 int blink_time;
4121};
4122
4123/**
4124 * enum ieee80211_tpt_led_trigger_flags - throughput trigger flags
4125 * @IEEE80211_TPT_LEDTRIG_FL_RADIO: enable blinking with radio
4126 * @IEEE80211_TPT_LEDTRIG_FL_WORK: enable blinking when working
4127 * @IEEE80211_TPT_LEDTRIG_FL_CONNECTED: enable blinking when at least one
4128 * interface is connected in some way, including being an AP
4129 */
4130enum ieee80211_tpt_led_trigger_flags {
4131 IEEE80211_TPT_LEDTRIG_FL_RADIO = BIT(0),
4132 IEEE80211_TPT_LEDTRIG_FL_WORK = BIT(1),
4133 IEEE80211_TPT_LEDTRIG_FL_CONNECTED = BIT(2),
4134};
4135
4136#ifdef CONFIG_MAC80211_LEDS
4137const char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
4138const char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
4139const char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
4140const char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
4141const char *
4142__ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw,
4143 unsigned int flags,
4144 const struct ieee80211_tpt_blink *blink_table,
4145 unsigned int blink_table_len);
4146#endif
4147/**
4148 * ieee80211_get_tx_led_name - get name of TX LED
4149 *
4150 * mac80211 creates a transmit LED trigger for each wireless hardware
4151 * that can be used to drive LEDs if your driver registers a LED device.
4152 * This function returns the name (or %NULL if not configured for LEDs)
4153 * of the trigger so you can automatically link the LED device.
4154 *
4155 * @hw: the hardware to get the LED trigger name for
4156 *
4157 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
4158 */
4159static inline const char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw)
4160{
4161#ifdef CONFIG_MAC80211_LEDS
4162 return __ieee80211_get_tx_led_name(hw);
4163#else
4164 return NULL;
4165#endif
4166}
4167
4168/**
4169 * ieee80211_get_rx_led_name - get name of RX LED
4170 *
4171 * mac80211 creates a receive LED trigger for each wireless hardware
4172 * that can be used to drive LEDs if your driver registers a LED device.
4173 * This function returns the name (or %NULL if not configured for LEDs)
4174 * of the trigger so you can automatically link the LED device.
4175 *
4176 * @hw: the hardware to get the LED trigger name for
4177 *
4178 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
4179 */
4180static inline const char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw)
4181{
4182#ifdef CONFIG_MAC80211_LEDS
4183 return __ieee80211_get_rx_led_name(hw);
4184#else
4185 return NULL;
4186#endif
4187}
4188
4189/**
4190 * ieee80211_get_assoc_led_name - get name of association LED
4191 *
4192 * mac80211 creates a association LED trigger for each wireless hardware
4193 * that can be used to drive LEDs if your driver registers a LED device.
4194 * This function returns the name (or %NULL if not configured for LEDs)
4195 * of the trigger so you can automatically link the LED device.
4196 *
4197 * @hw: the hardware to get the LED trigger name for
4198 *
4199 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
4200 */
4201static inline const char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
4202{
4203#ifdef CONFIG_MAC80211_LEDS
4204 return __ieee80211_get_assoc_led_name(hw);
4205#else
4206 return NULL;
4207#endif
4208}
4209
4210/**
4211 * ieee80211_get_radio_led_name - get name of radio LED
4212 *
4213 * mac80211 creates a radio change LED trigger for each wireless hardware
4214 * that can be used to drive LEDs if your driver registers a LED device.
4215 * This function returns the name (or %NULL if not configured for LEDs)
4216 * of the trigger so you can automatically link the LED device.
4217 *
4218 * @hw: the hardware to get the LED trigger name for
4219 *
4220 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
4221 */
4222static inline const char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw)
4223{
4224#ifdef CONFIG_MAC80211_LEDS
4225 return __ieee80211_get_radio_led_name(hw);
4226#else
4227 return NULL;
4228#endif
4229}
4230
4231/**
4232 * ieee80211_create_tpt_led_trigger - create throughput LED trigger
4233 * @hw: the hardware to create the trigger for
4234 * @flags: trigger flags, see &enum ieee80211_tpt_led_trigger_flags
4235 * @blink_table: the blink table -- needs to be ordered by throughput
4236 * @blink_table_len: size of the blink table
4237 *
4238 * Return: %NULL (in case of error, or if no LED triggers are
4239 * configured) or the name of the new trigger.
4240 *
4241 * Note: This function must be called before ieee80211_register_hw().
4242 */
4243static inline const char *
4244ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, unsigned int flags,
4245 const struct ieee80211_tpt_blink *blink_table,
4246 unsigned int blink_table_len)
4247{
4248#ifdef CONFIG_MAC80211_LEDS
4249 return __ieee80211_create_tpt_led_trigger(hw, flags, blink_table,
4250 blink_table_len);
4251#else
4252 return NULL;
4253#endif
4254}
4255
4256/**
4257 * ieee80211_unregister_hw - Unregister a hardware device
4258 *
4259 * This function instructs mac80211 to free allocated resources
4260 * and unregister netdevices from the networking subsystem.
4261 *
4262 * @hw: the hardware to unregister
4263 */
4264void ieee80211_unregister_hw(struct ieee80211_hw *hw);
4265
4266/**
4267 * ieee80211_free_hw - free hardware descriptor
4268 *
4269 * This function frees everything that was allocated, including the
4270 * private data for the driver. You must call ieee80211_unregister_hw()
4271 * before calling this function.
4272 *
4273 * @hw: the hardware to free
4274 */
4275void ieee80211_free_hw(struct ieee80211_hw *hw);
4276
4277/**
4278 * ieee80211_restart_hw - restart hardware completely
4279 *
4280 * Call this function when the hardware was restarted for some reason
4281 * (hardware error, ...) and the driver is unable to restore its state
4282 * by itself. mac80211 assumes that at this point the driver/hardware
4283 * is completely uninitialised and stopped, it starts the process by
4284 * calling the ->start() operation. The driver will need to reset all
4285 * internal state that it has prior to calling this function.
4286 *
4287 * @hw: the hardware to restart
4288 */
4289void ieee80211_restart_hw(struct ieee80211_hw *hw);
4290
4291/**
4292 * ieee80211_rx_napi - receive frame from NAPI context
4293 *
4294 * Use this function to hand received frames to mac80211. The receive
4295 * buffer in @skb must start with an IEEE 802.11 header. In case of a
4296 * paged @skb is used, the driver is recommended to put the ieee80211
4297 * header of the frame on the linear part of the @skb to avoid memory
4298 * allocation and/or memcpy by the stack.
4299 *
4300 * This function may not be called in IRQ context. Calls to this function
4301 * for a single hardware must be synchronized against each other. Calls to
4302 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
4303 * mixed for a single hardware. Must not run concurrently with
4304 * ieee80211_tx_status() or ieee80211_tx_status_ni().
4305 *
4306 * This function must be called with BHs disabled.
4307 *
4308 * @hw: the hardware this frame came in on
4309 * @sta: the station the frame was received from, or %NULL
4310 * @skb: the buffer to receive, owned by mac80211 after this call
4311 * @napi: the NAPI context
4312 */
4313void ieee80211_rx_napi(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
4314 struct sk_buff *skb, struct napi_struct *napi);
4315
4316/**
4317 * ieee80211_rx - receive frame
4318 *
4319 * Use this function to hand received frames to mac80211. The receive
4320 * buffer in @skb must start with an IEEE 802.11 header. In case of a
4321 * paged @skb is used, the driver is recommended to put the ieee80211
4322 * header of the frame on the linear part of the @skb to avoid memory
4323 * allocation and/or memcpy by the stack.
4324 *
4325 * This function may not be called in IRQ context. Calls to this function
4326 * for a single hardware must be synchronized against each other. Calls to
4327 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
4328 * mixed for a single hardware. Must not run concurrently with
4329 * ieee80211_tx_status() or ieee80211_tx_status_ni().
4330 *
4331 * In process context use instead ieee80211_rx_ni().
4332 *
4333 * @hw: the hardware this frame came in on
4334 * @skb: the buffer to receive, owned by mac80211 after this call
4335 */
4336static inline void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb)
4337{
4338 ieee80211_rx_napi(hw, NULL, skb, NULL);
4339}
4340
4341/**
4342 * ieee80211_rx_irqsafe - receive frame
4343 *
4344 * Like ieee80211_rx() but can be called in IRQ context
4345 * (internally defers to a tasklet.)
4346 *
4347 * Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not
4348 * be mixed for a single hardware.Must not run concurrently with
4349 * ieee80211_tx_status() or ieee80211_tx_status_ni().
4350 *
4351 * @hw: the hardware this frame came in on
4352 * @skb: the buffer to receive, owned by mac80211 after this call
4353 */
4354void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb);
4355
4356/**
4357 * ieee80211_rx_ni - receive frame (in process context)
4358 *
4359 * Like ieee80211_rx() but can be called in process context
4360 * (internally disables bottom halves).
4361 *
4362 * Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may
4363 * not be mixed for a single hardware. Must not run concurrently with
4364 * ieee80211_tx_status() or ieee80211_tx_status_ni().
4365 *
4366 * @hw: the hardware this frame came in on
4367 * @skb: the buffer to receive, owned by mac80211 after this call
4368 */
4369static inline void ieee80211_rx_ni(struct ieee80211_hw *hw,
4370 struct sk_buff *skb)
4371{
4372 local_bh_disable();
4373 ieee80211_rx(hw, skb);
4374 local_bh_enable();
4375}
4376
4377/**
4378 * ieee80211_sta_ps_transition - PS transition for connected sta
4379 *
4380 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS
4381 * flag set, use this function to inform mac80211 about a connected station
4382 * entering/leaving PS mode.
4383 *
4384 * This function may not be called in IRQ context or with softirqs enabled.
4385 *
4386 * Calls to this function for a single hardware must be synchronized against
4387 * each other.
4388 *
4389 * @sta: currently connected sta
4390 * @start: start or stop PS
4391 *
4392 * Return: 0 on success. -EINVAL when the requested PS mode is already set.
4393 */
4394int ieee80211_sta_ps_transition(struct ieee80211_sta *sta, bool start);
4395
4396/**
4397 * ieee80211_sta_ps_transition_ni - PS transition for connected sta
4398 * (in process context)
4399 *
4400 * Like ieee80211_sta_ps_transition() but can be called in process context
4401 * (internally disables bottom halves). Concurrent call restriction still
4402 * applies.
4403 *
4404 * @sta: currently connected sta
4405 * @start: start or stop PS
4406 *
4407 * Return: Like ieee80211_sta_ps_transition().
4408 */
4409static inline int ieee80211_sta_ps_transition_ni(struct ieee80211_sta *sta,
4410 bool start)
4411{
4412 int ret;
4413
4414 local_bh_disable();
4415 ret = ieee80211_sta_ps_transition(sta, start);
4416 local_bh_enable();
4417
4418 return ret;
4419}
4420
4421/**
4422 * ieee80211_sta_pspoll - PS-Poll frame received
4423 * @sta: currently connected station
4424 *
4425 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS flag set,
4426 * use this function to inform mac80211 that a PS-Poll frame from a
4427 * connected station was received.
4428 * This must be used in conjunction with ieee80211_sta_ps_transition()
4429 * and possibly ieee80211_sta_uapsd_trigger(); calls to all three must
4430 * be serialized.
4431 */
4432void ieee80211_sta_pspoll(struct ieee80211_sta *sta);
4433
4434/**
4435 * ieee80211_sta_uapsd_trigger - (potential) U-APSD trigger frame received
4436 * @sta: currently connected station
4437 * @tid: TID of the received (potential) trigger frame
4438 *
4439 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS flag set,
4440 * use this function to inform mac80211 that a (potential) trigger frame
4441 * from a connected station was received.
4442 * This must be used in conjunction with ieee80211_sta_ps_transition()
4443 * and possibly ieee80211_sta_pspoll(); calls to all three must be
4444 * serialized.
4445 * %IEEE80211_NUM_TIDS can be passed as the tid if the tid is unknown.
4446 * In this case, mac80211 will not check that this tid maps to an AC
4447 * that is trigger enabled and assume that the caller did the proper
4448 * checks.
4449 */
4450void ieee80211_sta_uapsd_trigger(struct ieee80211_sta *sta, u8 tid);
4451
4452/*
4453 * The TX headroom reserved by mac80211 for its own tx_status functions.
4454 * This is enough for the radiotap header.
4455 */
4456#define IEEE80211_TX_STATUS_HEADROOM ALIGN(14, 4)
4457
4458/**
4459 * ieee80211_sta_set_buffered - inform mac80211 about driver-buffered frames
4460 * @sta: &struct ieee80211_sta pointer for the sleeping station
4461 * @tid: the TID that has buffered frames
4462 * @buffered: indicates whether or not frames are buffered for this TID
4463 *
4464 * If a driver buffers frames for a powersave station instead of passing
4465 * them back to mac80211 for retransmission, the station may still need
4466 * to be told that there are buffered frames via the TIM bit.
4467 *
4468 * This function informs mac80211 whether or not there are frames that are
4469 * buffered in the driver for a given TID; mac80211 can then use this data
4470 * to set the TIM bit (NOTE: This may call back into the driver's set_tim
4471 * call! Beware of the locking!)
4472 *
4473 * If all frames are released to the station (due to PS-poll or uAPSD)
4474 * then the driver needs to inform mac80211 that there no longer are
4475 * frames buffered. However, when the station wakes up mac80211 assumes
4476 * that all buffered frames will be transmitted and clears this data,
4477 * drivers need to make sure they inform mac80211 about all buffered
4478 * frames on the sleep transition (sta_notify() with %STA_NOTIFY_SLEEP).
4479 *
4480 * Note that technically mac80211 only needs to know this per AC, not per
4481 * TID, but since driver buffering will inevitably happen per TID (since
4482 * it is related to aggregation) it is easier to make mac80211 map the
4483 * TID to the AC as required instead of keeping track in all drivers that
4484 * use this API.
4485 */
4486void ieee80211_sta_set_buffered(struct ieee80211_sta *sta,
4487 u8 tid, bool buffered);
4488
4489/**
4490 * ieee80211_get_tx_rates - get the selected transmit rates for a packet
4491 *
4492 * Call this function in a driver with per-packet rate selection support
4493 * to combine the rate info in the packet tx info with the most recent
4494 * rate selection table for the station entry.
4495 *
4496 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4497 * @sta: the receiver station to which this packet is sent.
4498 * @skb: the frame to be transmitted.
4499 * @dest: buffer for extracted rate/retry information
4500 * @max_rates: maximum number of rates to fetch
4501 */
4502void ieee80211_get_tx_rates(struct ieee80211_vif *vif,
4503 struct ieee80211_sta *sta,
4504 struct sk_buff *skb,
4505 struct ieee80211_tx_rate *dest,
4506 int max_rates);
4507
4508/**
4509 * ieee80211_sta_set_expected_throughput - set the expected tpt for a station
4510 *
4511 * Call this function to notify mac80211 about a change in expected throughput
4512 * to a station. A driver for a device that does rate control in firmware can
4513 * call this function when the expected throughput estimate towards a station
4514 * changes. The information is used to tune the CoDel AQM applied to traffic
4515 * going towards that station (which can otherwise be too aggressive and cause
4516 * slow stations to starve).
4517 *
4518 * @pubsta: the station to set throughput for.
4519 * @thr: the current expected throughput in kbps.
4520 */
4521void ieee80211_sta_set_expected_throughput(struct ieee80211_sta *pubsta,
4522 u32 thr);
4523
4524/**
4525 * ieee80211_tx_rate_update - transmit rate update callback
4526 *
4527 * Drivers should call this functions with a non-NULL pub sta
4528 * This function can be used in drivers that does not have provision
4529 * in updating the tx rate in data path.
4530 *
4531 * @hw: the hardware the frame was transmitted by
4532 * @pubsta: the station to update the tx rate for.
4533 * @info: tx status information
4534 */
4535void ieee80211_tx_rate_update(struct ieee80211_hw *hw,
4536 struct ieee80211_sta *pubsta,
4537 struct ieee80211_tx_info *info);
4538
4539/**
4540 * ieee80211_tx_status - transmit status callback
4541 *
4542 * Call this function for all transmitted frames after they have been
4543 * transmitted. It is permissible to not call this function for
4544 * multicast frames but this can affect statistics.
4545 *
4546 * This function may not be called in IRQ context. Calls to this function
4547 * for a single hardware must be synchronized against each other. Calls
4548 * to this function, ieee80211_tx_status_ni() and ieee80211_tx_status_irqsafe()
4549 * may not be mixed for a single hardware. Must not run concurrently with
4550 * ieee80211_rx() or ieee80211_rx_ni().
4551 *
4552 * @hw: the hardware the frame was transmitted by
4553 * @skb: the frame that was transmitted, owned by mac80211 after this call
4554 */
4555void ieee80211_tx_status(struct ieee80211_hw *hw,
4556 struct sk_buff *skb);
4557
4558/**
4559 * ieee80211_tx_status_ext - extended transmit status callback
4560 *
4561 * This function can be used as a replacement for ieee80211_tx_status
4562 * in drivers that may want to provide extra information that does not
4563 * fit into &struct ieee80211_tx_info.
4564 *
4565 * Calls to this function for a single hardware must be synchronized
4566 * against each other. Calls to this function, ieee80211_tx_status_ni()
4567 * and ieee80211_tx_status_irqsafe() may not be mixed for a single hardware.
4568 *
4569 * @hw: the hardware the frame was transmitted by
4570 * @status: tx status information
4571 */
4572void ieee80211_tx_status_ext(struct ieee80211_hw *hw,
4573 struct ieee80211_tx_status *status);
4574
4575/**
4576 * ieee80211_tx_status_noskb - transmit status callback without skb
4577 *
4578 * This function can be used as a replacement for ieee80211_tx_status
4579 * in drivers that cannot reliably map tx status information back to
4580 * specific skbs.
4581 *
4582 * Calls to this function for a single hardware must be synchronized
4583 * against each other. Calls to this function, ieee80211_tx_status_ni()
4584 * and ieee80211_tx_status_irqsafe() may not be mixed for a single hardware.
4585 *
4586 * @hw: the hardware the frame was transmitted by
4587 * @sta: the receiver station to which this packet is sent
4588 * (NULL for multicast packets)
4589 * @info: tx status information
4590 */
4591static inline void ieee80211_tx_status_noskb(struct ieee80211_hw *hw,
4592 struct ieee80211_sta *sta,
4593 struct ieee80211_tx_info *info)
4594{
4595 struct ieee80211_tx_status status = {
4596 .sta = sta,
4597 .info = info,
4598 };
4599
4600 ieee80211_tx_status_ext(hw, &status);
4601}
4602
4603/**
4604 * ieee80211_tx_status_ni - transmit status callback (in process context)
4605 *
4606 * Like ieee80211_tx_status() but can be called in process context.
4607 *
4608 * Calls to this function, ieee80211_tx_status() and
4609 * ieee80211_tx_status_irqsafe() may not be mixed
4610 * for a single hardware.
4611 *
4612 * @hw: the hardware the frame was transmitted by
4613 * @skb: the frame that was transmitted, owned by mac80211 after this call
4614 */
4615static inline void ieee80211_tx_status_ni(struct ieee80211_hw *hw,
4616 struct sk_buff *skb)
4617{
4618 local_bh_disable();
4619 ieee80211_tx_status(hw, skb);
4620 local_bh_enable();
4621}
4622
4623/**
4624 * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback
4625 *
4626 * Like ieee80211_tx_status() but can be called in IRQ context
4627 * (internally defers to a tasklet.)
4628 *
4629 * Calls to this function, ieee80211_tx_status() and
4630 * ieee80211_tx_status_ni() may not be mixed for a single hardware.
4631 *
4632 * @hw: the hardware the frame was transmitted by
4633 * @skb: the frame that was transmitted, owned by mac80211 after this call
4634 */
4635void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
4636 struct sk_buff *skb);
4637
4638/**
4639 * ieee80211_report_low_ack - report non-responding station
4640 *
4641 * When operating in AP-mode, call this function to report a non-responding
4642 * connected STA.
4643 *
4644 * @sta: the non-responding connected sta
4645 * @num_packets: number of packets sent to @sta without a response
4646 */
4647void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets);
4648
4649#define IEEE80211_MAX_CSA_COUNTERS_NUM 2
4650
4651/**
4652 * struct ieee80211_mutable_offsets - mutable beacon offsets
4653 * @tim_offset: position of TIM element
4654 * @tim_length: size of TIM element
4655 * @csa_counter_offs: array of IEEE80211_MAX_CSA_COUNTERS_NUM offsets
4656 * to CSA counters. This array can contain zero values which
4657 * should be ignored.
4658 */
4659struct ieee80211_mutable_offsets {
4660 u16 tim_offset;
4661 u16 tim_length;
4662
4663 u16 csa_counter_offs[IEEE80211_MAX_CSA_COUNTERS_NUM];
4664};
4665
4666/**
4667 * ieee80211_beacon_get_template - beacon template generation function
4668 * @hw: pointer obtained from ieee80211_alloc_hw().
4669 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4670 * @offs: &struct ieee80211_mutable_offsets pointer to struct that will
4671 * receive the offsets that may be updated by the driver.
4672 *
4673 * If the driver implements beaconing modes, it must use this function to
4674 * obtain the beacon template.
4675 *
4676 * This function should be used if the beacon frames are generated by the
4677 * device, and then the driver must use the returned beacon as the template
4678 * The driver or the device are responsible to update the DTIM and, when
4679 * applicable, the CSA count.
4680 *
4681 * The driver is responsible for freeing the returned skb.
4682 *
4683 * Return: The beacon template. %NULL on error.
4684 */
4685struct sk_buff *
4686ieee80211_beacon_get_template(struct ieee80211_hw *hw,
4687 struct ieee80211_vif *vif,
4688 struct ieee80211_mutable_offsets *offs);
4689
4690/**
4691 * ieee80211_beacon_get_tim - beacon generation function
4692 * @hw: pointer obtained from ieee80211_alloc_hw().
4693 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4694 * @tim_offset: pointer to variable that will receive the TIM IE offset.
4695 * Set to 0 if invalid (in non-AP modes).
4696 * @tim_length: pointer to variable that will receive the TIM IE length,
4697 * (including the ID and length bytes!).
4698 * Set to 0 if invalid (in non-AP modes).
4699 *
4700 * If the driver implements beaconing modes, it must use this function to
4701 * obtain the beacon frame.
4702 *
4703 * If the beacon frames are generated by the host system (i.e., not in
4704 * hardware/firmware), the driver uses this function to get each beacon
4705 * frame from mac80211 -- it is responsible for calling this function exactly
4706 * once before the beacon is needed (e.g. based on hardware interrupt).
4707 *
4708 * The driver is responsible for freeing the returned skb.
4709 *
4710 * Return: The beacon template. %NULL on error.
4711 */
4712struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw,
4713 struct ieee80211_vif *vif,
4714 u16 *tim_offset, u16 *tim_length);
4715
4716/**
4717 * ieee80211_beacon_get - beacon generation function
4718 * @hw: pointer obtained from ieee80211_alloc_hw().
4719 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4720 *
4721 * See ieee80211_beacon_get_tim().
4722 *
4723 * Return: See ieee80211_beacon_get_tim().
4724 */
4725static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
4726 struct ieee80211_vif *vif)
4727{
4728 return ieee80211_beacon_get_tim(hw, vif, NULL, NULL);
4729}
4730
4731/**
4732 * ieee80211_csa_update_counter - request mac80211 to decrement the csa counter
4733 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4734 *
4735 * The csa counter should be updated after each beacon transmission.
4736 * This function is called implicitly when
4737 * ieee80211_beacon_get/ieee80211_beacon_get_tim are called, however if the
4738 * beacon frames are generated by the device, the driver should call this
4739 * function after each beacon transmission to sync mac80211's csa counters.
4740 *
4741 * Return: new csa counter value
4742 */
4743u8 ieee80211_csa_update_counter(struct ieee80211_vif *vif);
4744
4745/**
4746 * ieee80211_csa_set_counter - request mac80211 to set csa counter
4747 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4748 * @counter: the new value for the counter
4749 *
4750 * The csa counter can be changed by the device, this API should be
4751 * used by the device driver to update csa counter in mac80211.
4752 *
4753 * It should never be used together with ieee80211_csa_update_counter(),
4754 * as it will cause a race condition around the counter value.
4755 */
4756void ieee80211_csa_set_counter(struct ieee80211_vif *vif, u8 counter);
4757
4758/**
4759 * ieee80211_csa_finish - notify mac80211 about channel switch
4760 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4761 *
4762 * After a channel switch announcement was scheduled and the counter in this
4763 * announcement hits 1, this function must be called by the driver to
4764 * notify mac80211 that the channel can be changed.
4765 */
4766void ieee80211_csa_finish(struct ieee80211_vif *vif);
4767
4768/**
4769 * ieee80211_csa_is_complete - find out if counters reached 1
4770 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4771 *
4772 * This function returns whether the channel switch counters reached zero.
4773 */
4774bool ieee80211_csa_is_complete(struct ieee80211_vif *vif);
4775
4776
4777/**
4778 * ieee80211_proberesp_get - retrieve a Probe Response template
4779 * @hw: pointer obtained from ieee80211_alloc_hw().
4780 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4781 *
4782 * Creates a Probe Response template which can, for example, be uploaded to
4783 * hardware. The destination address should be set by the caller.
4784 *
4785 * Can only be called in AP mode.
4786 *
4787 * Return: The Probe Response template. %NULL on error.
4788 */
4789struct sk_buff *ieee80211_proberesp_get(struct ieee80211_hw *hw,
4790 struct ieee80211_vif *vif);
4791
4792/**
4793 * ieee80211_pspoll_get - retrieve a PS Poll template
4794 * @hw: pointer obtained from ieee80211_alloc_hw().
4795 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4796 *
4797 * Creates a PS Poll a template which can, for example, uploaded to
4798 * hardware. The template must be updated after association so that correct
4799 * AID, BSSID and MAC address is used.
4800 *
4801 * Note: Caller (or hardware) is responsible for setting the
4802 * &IEEE80211_FCTL_PM bit.
4803 *
4804 * Return: The PS Poll template. %NULL on error.
4805 */
4806struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw,
4807 struct ieee80211_vif *vif);
4808
4809/**
4810 * ieee80211_nullfunc_get - retrieve a nullfunc template
4811 * @hw: pointer obtained from ieee80211_alloc_hw().
4812 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4813 * @qos_ok: QoS NDP is acceptable to the caller, this should be set
4814 * if at all possible
4815 *
4816 * Creates a Nullfunc template which can, for example, uploaded to
4817 * hardware. The template must be updated after association so that correct
4818 * BSSID and address is used.
4819 *
4820 * If @qos_ndp is set and the association is to an AP with QoS/WMM, the
4821 * returned packet will be QoS NDP.
4822 *
4823 * Note: Caller (or hardware) is responsible for setting the
4824 * &IEEE80211_FCTL_PM bit as well as Duration and Sequence Control fields.
4825 *
4826 * Return: The nullfunc template. %NULL on error.
4827 */
4828struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw,
4829 struct ieee80211_vif *vif,
4830 bool qos_ok);
4831
4832/**
4833 * ieee80211_probereq_get - retrieve a Probe Request template
4834 * @hw: pointer obtained from ieee80211_alloc_hw().
4835 * @src_addr: source MAC address
4836 * @ssid: SSID buffer
4837 * @ssid_len: length of SSID
4838 * @tailroom: tailroom to reserve at end of SKB for IEs
4839 *
4840 * Creates a Probe Request template which can, for example, be uploaded to
4841 * hardware.
4842 *
4843 * Return: The Probe Request template. %NULL on error.
4844 */
4845struct sk_buff *ieee80211_probereq_get(struct ieee80211_hw *hw,
4846 const u8 *src_addr,
4847 const u8 *ssid, size_t ssid_len,
4848 size_t tailroom);
4849
4850/**
4851 * ieee80211_rts_get - RTS frame generation function
4852 * @hw: pointer obtained from ieee80211_alloc_hw().
4853 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4854 * @frame: pointer to the frame that is going to be protected by the RTS.
4855 * @frame_len: the frame length (in octets).
4856 * @frame_txctl: &struct ieee80211_tx_info of the frame.
4857 * @rts: The buffer where to store the RTS frame.
4858 *
4859 * If the RTS frames are generated by the host system (i.e., not in
4860 * hardware/firmware), the low-level driver uses this function to receive
4861 * the next RTS frame from the 802.11 code. The low-level is responsible
4862 * for calling this function before and RTS frame is needed.
4863 */
4864void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
4865 const void *frame, size_t frame_len,
4866 const struct ieee80211_tx_info *frame_txctl,
4867 struct ieee80211_rts *rts);
4868
4869/**
4870 * ieee80211_rts_duration - Get the duration field for an RTS frame
4871 * @hw: pointer obtained from ieee80211_alloc_hw().
4872 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4873 * @frame_len: the length of the frame that is going to be protected by the RTS.
4874 * @frame_txctl: &struct ieee80211_tx_info of the frame.
4875 *
4876 * If the RTS is generated in firmware, but the host system must provide
4877 * the duration field, the low-level driver uses this function to receive
4878 * the duration field value in little-endian byteorder.
4879 *
4880 * Return: The duration.
4881 */
4882__le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
4883 struct ieee80211_vif *vif, size_t frame_len,
4884 const struct ieee80211_tx_info *frame_txctl);
4885
4886/**
4887 * ieee80211_ctstoself_get - CTS-to-self frame generation function
4888 * @hw: pointer obtained from ieee80211_alloc_hw().
4889 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4890 * @frame: pointer to the frame that is going to be protected by the CTS-to-self.
4891 * @frame_len: the frame length (in octets).
4892 * @frame_txctl: &struct ieee80211_tx_info of the frame.
4893 * @cts: The buffer where to store the CTS-to-self frame.
4894 *
4895 * If the CTS-to-self frames are generated by the host system (i.e., not in
4896 * hardware/firmware), the low-level driver uses this function to receive
4897 * the next CTS-to-self frame from the 802.11 code. The low-level is responsible
4898 * for calling this function before and CTS-to-self frame is needed.
4899 */
4900void ieee80211_ctstoself_get(struct ieee80211_hw *hw,
4901 struct ieee80211_vif *vif,
4902 const void *frame, size_t frame_len,
4903 const struct ieee80211_tx_info *frame_txctl,
4904 struct ieee80211_cts *cts);
4905
4906/**
4907 * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
4908 * @hw: pointer obtained from ieee80211_alloc_hw().
4909 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4910 * @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
4911 * @frame_txctl: &struct ieee80211_tx_info of the frame.
4912 *
4913 * If the CTS-to-self is generated in firmware, but the host system must provide
4914 * the duration field, the low-level driver uses this function to receive
4915 * the duration field value in little-endian byteorder.
4916 *
4917 * Return: The duration.
4918 */
4919__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
4920 struct ieee80211_vif *vif,
4921 size_t frame_len,
4922 const struct ieee80211_tx_info *frame_txctl);
4923
4924/**
4925 * ieee80211_generic_frame_duration - Calculate the duration field for a frame
4926 * @hw: pointer obtained from ieee80211_alloc_hw().
4927 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4928 * @band: the band to calculate the frame duration on
4929 * @frame_len: the length of the frame.
4930 * @rate: the rate at which the frame is going to be transmitted.
4931 *
4932 * Calculate the duration field of some generic frame, given its
4933 * length and transmission rate (in 100kbps).
4934 *
4935 * Return: The duration.
4936 */
4937__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
4938 struct ieee80211_vif *vif,
4939 enum nl80211_band band,
4940 size_t frame_len,
4941 struct ieee80211_rate *rate);
4942
4943/**
4944 * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
4945 * @hw: pointer as obtained from ieee80211_alloc_hw().
4946 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4947 *
4948 * Function for accessing buffered broadcast and multicast frames. If
4949 * hardware/firmware does not implement buffering of broadcast/multicast
4950 * frames when power saving is used, 802.11 code buffers them in the host
4951 * memory. The low-level driver uses this function to fetch next buffered
4952 * frame. In most cases, this is used when generating beacon frame.
4953 *
4954 * Return: A pointer to the next buffered skb or NULL if no more buffered
4955 * frames are available.
4956 *
4957 * Note: buffered frames are returned only after DTIM beacon frame was
4958 * generated with ieee80211_beacon_get() and the low-level driver must thus
4959 * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns
4960 * NULL if the previous generated beacon was not DTIM, so the low-level driver
4961 * does not need to check for DTIM beacons separately and should be able to
4962 * use common code for all beacons.
4963 */
4964struct sk_buff *
4965ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
4966
4967/**
4968 * ieee80211_get_tkip_p1k_iv - get a TKIP phase 1 key for IV32
4969 *
4970 * This function returns the TKIP phase 1 key for the given IV32.
4971 *
4972 * @keyconf: the parameter passed with the set key
4973 * @iv32: IV32 to get the P1K for
4974 * @p1k: a buffer to which the key will be written, as 5 u16 values
4975 */
4976void ieee80211_get_tkip_p1k_iv(struct ieee80211_key_conf *keyconf,
4977 u32 iv32, u16 *p1k);
4978
4979/**
4980 * ieee80211_get_tkip_p1k - get a TKIP phase 1 key
4981 *
4982 * This function returns the TKIP phase 1 key for the IV32 taken
4983 * from the given packet.
4984 *
4985 * @keyconf: the parameter passed with the set key
4986 * @skb: the packet to take the IV32 value from that will be encrypted
4987 * with this P1K
4988 * @p1k: a buffer to which the key will be written, as 5 u16 values
4989 */
4990static inline void ieee80211_get_tkip_p1k(struct ieee80211_key_conf *keyconf,
4991 struct sk_buff *skb, u16 *p1k)
4992{
4993 struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
4994 const u8 *data = (u8 *)hdr + ieee80211_hdrlen(hdr->frame_control);
4995 u32 iv32 = get_unaligned_le32(&data[4]);
4996
4997 ieee80211_get_tkip_p1k_iv(keyconf, iv32, p1k);
4998}
4999
5000/**
5001 * ieee80211_get_tkip_rx_p1k - get a TKIP phase 1 key for RX
5002 *
5003 * This function returns the TKIP phase 1 key for the given IV32
5004 * and transmitter address.
5005 *
5006 * @keyconf: the parameter passed with the set key
5007 * @ta: TA that will be used with the key
5008 * @iv32: IV32 to get the P1K for
5009 * @p1k: a buffer to which the key will be written, as 5 u16 values
5010 */
5011void ieee80211_get_tkip_rx_p1k(struct ieee80211_key_conf *keyconf,
5012 const u8 *ta, u32 iv32, u16 *p1k);
5013
5014/**
5015 * ieee80211_get_tkip_p2k - get a TKIP phase 2 key
5016 *
5017 * This function computes the TKIP RC4 key for the IV values
5018 * in the packet.
5019 *
5020 * @keyconf: the parameter passed with the set key
5021 * @skb: the packet to take the IV32/IV16 values from that will be
5022 * encrypted with this key
5023 * @p2k: a buffer to which the key will be written, 16 bytes
5024 */
5025void ieee80211_get_tkip_p2k(struct ieee80211_key_conf *keyconf,
5026 struct sk_buff *skb, u8 *p2k);
5027
5028/**
5029 * ieee80211_tkip_add_iv - write TKIP IV and Ext. IV to pos
5030 *
5031 * @pos: start of crypto header
5032 * @keyconf: the parameter passed with the set key
5033 * @pn: PN to add
5034 *
5035 * Returns: pointer to the octet following IVs (i.e. beginning of
5036 * the packet payload)
5037 *
5038 * This function writes the tkip IV value to pos (which should
5039 * point to the crypto header)
5040 */
5041u8 *ieee80211_tkip_add_iv(u8 *pos, struct ieee80211_key_conf *keyconf, u64 pn);
5042
5043/**
5044 * ieee80211_get_key_rx_seq - get key RX sequence counter
5045 *
5046 * @keyconf: the parameter passed with the set key
5047 * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only);
5048 * the value on TID 0 is also used for non-QoS frames. For
5049 * CMAC, only TID 0 is valid.
5050 * @seq: buffer to receive the sequence data
5051 *
5052 * This function allows a driver to retrieve the current RX IV/PNs
5053 * for the given key. It must not be called if IV checking is done
5054 * by the device and not by mac80211.
5055 *
5056 * Note that this function may only be called when no RX processing
5057 * can be done concurrently.
5058 */
5059void ieee80211_get_key_rx_seq(struct ieee80211_key_conf *keyconf,
5060 int tid, struct ieee80211_key_seq *seq);
5061
5062/**
5063 * ieee80211_set_key_rx_seq - set key RX sequence counter
5064 *
5065 * @keyconf: the parameter passed with the set key
5066 * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only);
5067 * the value on TID 0 is also used for non-QoS frames. For
5068 * CMAC, only TID 0 is valid.
5069 * @seq: new sequence data
5070 *
5071 * This function allows a driver to set the current RX IV/PNs for the
5072 * given key. This is useful when resuming from WoWLAN sleep and GTK
5073 * rekey may have been done while suspended. It should not be called
5074 * if IV checking is done by the device and not by mac80211.
5075 *
5076 * Note that this function may only be called when no RX processing
5077 * can be done concurrently.
5078 */
5079void ieee80211_set_key_rx_seq(struct ieee80211_key_conf *keyconf,
5080 int tid, struct ieee80211_key_seq *seq);
5081
5082/**
5083 * ieee80211_remove_key - remove the given key
5084 * @keyconf: the parameter passed with the set key
5085 *
5086 * Remove the given key. If the key was uploaded to the hardware at the
5087 * time this function is called, it is not deleted in the hardware but
5088 * instead assumed to have been removed already.
5089 *
5090 * Note that due to locking considerations this function can (currently)
5091 * only be called during key iteration (ieee80211_iter_keys().)
5092 */
5093void ieee80211_remove_key(struct ieee80211_key_conf *keyconf);
5094
5095/**
5096 * ieee80211_gtk_rekey_add - add a GTK key from rekeying during WoWLAN
5097 * @vif: the virtual interface to add the key on
5098 * @keyconf: new key data
5099 *
5100 * When GTK rekeying was done while the system was suspended, (a) new
5101 * key(s) will be available. These will be needed by mac80211 for proper
5102 * RX processing, so this function allows setting them.
5103 *
5104 * The function returns the newly allocated key structure, which will
5105 * have similar contents to the passed key configuration but point to
5106 * mac80211-owned memory. In case of errors, the function returns an
5107 * ERR_PTR(), use IS_ERR() etc.
5108 *
5109 * Note that this function assumes the key isn't added to hardware
5110 * acceleration, so no TX will be done with the key. Since it's a GTK
5111 * on managed (station) networks, this is true anyway. If the driver
5112 * calls this function from the resume callback and subsequently uses
5113 * the return code 1 to reconfigure the device, this key will be part
5114 * of the reconfiguration.
5115 *
5116 * Note that the driver should also call ieee80211_set_key_rx_seq()
5117 * for the new key for each TID to set up sequence counters properly.
5118 *
5119 * IMPORTANT: If this replaces a key that is present in the hardware,
5120 * then it will attempt to remove it during this call. In many cases
5121 * this isn't what you want, so call ieee80211_remove_key() first for
5122 * the key that's being replaced.
5123 */
5124struct ieee80211_key_conf *
5125ieee80211_gtk_rekey_add(struct ieee80211_vif *vif,
5126 struct ieee80211_key_conf *keyconf);
5127
5128/**
5129 * ieee80211_gtk_rekey_notify - notify userspace supplicant of rekeying
5130 * @vif: virtual interface the rekeying was done on
5131 * @bssid: The BSSID of the AP, for checking association
5132 * @replay_ctr: the new replay counter after GTK rekeying
5133 * @gfp: allocation flags
5134 */
5135void ieee80211_gtk_rekey_notify(struct ieee80211_vif *vif, const u8 *bssid,
5136 const u8 *replay_ctr, gfp_t gfp);
5137
5138/**
5139 * ieee80211_wake_queue - wake specific queue
5140 * @hw: pointer as obtained from ieee80211_alloc_hw().
5141 * @queue: queue number (counted from zero).
5142 *
5143 * Drivers should use this function instead of netif_wake_queue.
5144 */
5145void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue);
5146
5147/**
5148 * ieee80211_stop_queue - stop specific queue
5149 * @hw: pointer as obtained from ieee80211_alloc_hw().
5150 * @queue: queue number (counted from zero).
5151 *
5152 * Drivers should use this function instead of netif_stop_queue.
5153 */
5154void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue);
5155
5156/**
5157 * ieee80211_queue_stopped - test status of the queue
5158 * @hw: pointer as obtained from ieee80211_alloc_hw().
5159 * @queue: queue number (counted from zero).
5160 *
5161 * Drivers should use this function instead of netif_stop_queue.
5162 *
5163 * Return: %true if the queue is stopped. %false otherwise.
5164 */
5165
5166int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue);
5167
5168/**
5169 * ieee80211_stop_queues - stop all queues
5170 * @hw: pointer as obtained from ieee80211_alloc_hw().
5171 *
5172 * Drivers should use this function instead of netif_stop_queue.
5173 */
5174void ieee80211_stop_queues(struct ieee80211_hw *hw);
5175
5176/**
5177 * ieee80211_wake_queues - wake all queues
5178 * @hw: pointer as obtained from ieee80211_alloc_hw().
5179 *
5180 * Drivers should use this function instead of netif_wake_queue.
5181 */
5182void ieee80211_wake_queues(struct ieee80211_hw *hw);
5183
5184/**
5185 * ieee80211_scan_completed - completed hardware scan
5186 *
5187 * When hardware scan offload is used (i.e. the hw_scan() callback is
5188 * assigned) this function needs to be called by the driver to notify
5189 * mac80211 that the scan finished. This function can be called from
5190 * any context, including hardirq context.
5191 *
5192 * @hw: the hardware that finished the scan
5193 * @info: information about the completed scan
5194 */
5195void ieee80211_scan_completed(struct ieee80211_hw *hw,
5196 struct cfg80211_scan_info *info);
5197
5198/**
5199 * ieee80211_sched_scan_results - got results from scheduled scan
5200 *
5201 * When a scheduled scan is running, this function needs to be called by the
5202 * driver whenever there are new scan results available.
5203 *
5204 * @hw: the hardware that is performing scheduled scans
5205 */
5206void ieee80211_sched_scan_results(struct ieee80211_hw *hw);
5207
5208/**
5209 * ieee80211_sched_scan_stopped - inform that the scheduled scan has stopped
5210 *
5211 * When a scheduled scan is running, this function can be called by
5212 * the driver if it needs to stop the scan to perform another task.
5213 * Usual scenarios are drivers that cannot continue the scheduled scan
5214 * while associating, for instance.
5215 *
5216 * @hw: the hardware that is performing scheduled scans
5217 */
5218void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw);
5219
5220/**
5221 * enum ieee80211_interface_iteration_flags - interface iteration flags
5222 * @IEEE80211_IFACE_ITER_NORMAL: Iterate over all interfaces that have
5223 * been added to the driver; However, note that during hardware
5224 * reconfiguration (after restart_hw) it will iterate over a new
5225 * interface and over all the existing interfaces even if they
5226 * haven't been re-added to the driver yet.
5227 * @IEEE80211_IFACE_ITER_RESUME_ALL: During resume, iterate over all
5228 * interfaces, even if they haven't been re-added to the driver yet.
5229 * @IEEE80211_IFACE_ITER_ACTIVE: Iterate only active interfaces (netdev is up).
5230 */
5231enum ieee80211_interface_iteration_flags {
5232 IEEE80211_IFACE_ITER_NORMAL = 0,
5233 IEEE80211_IFACE_ITER_RESUME_ALL = BIT(0),
5234 IEEE80211_IFACE_ITER_ACTIVE = BIT(1),
5235};
5236
5237/**
5238 * ieee80211_iterate_interfaces - iterate interfaces
5239 *
5240 * This function iterates over the interfaces associated with a given
5241 * hardware and calls the callback for them. This includes active as well as
5242 * inactive interfaces. This function allows the iterator function to sleep.
5243 * Will iterate over a new interface during add_interface().
5244 *
5245 * @hw: the hardware struct of which the interfaces should be iterated over
5246 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
5247 * @iterator: the iterator function to call
5248 * @data: first argument of the iterator function
5249 */
5250void ieee80211_iterate_interfaces(struct ieee80211_hw *hw, u32 iter_flags,
5251 void (*iterator)(void *data, u8 *mac,
5252 struct ieee80211_vif *vif),
5253 void *data);
5254
5255/**
5256 * ieee80211_iterate_active_interfaces - iterate active interfaces
5257 *
5258 * This function iterates over the interfaces associated with a given
5259 * hardware that are currently active and calls the callback for them.
5260 * This function allows the iterator function to sleep, when the iterator
5261 * function is atomic @ieee80211_iterate_active_interfaces_atomic can
5262 * be used.
5263 * Does not iterate over a new interface during add_interface().
5264 *
5265 * @hw: the hardware struct of which the interfaces should be iterated over
5266 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
5267 * @iterator: the iterator function to call
5268 * @data: first argument of the iterator function
5269 */
5270static inline void
5271ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, u32 iter_flags,
5272 void (*iterator)(void *data, u8 *mac,
5273 struct ieee80211_vif *vif),
5274 void *data)
5275{
5276 ieee80211_iterate_interfaces(hw,
5277 iter_flags | IEEE80211_IFACE_ITER_ACTIVE,
5278 iterator, data);
5279}
5280
5281/**
5282 * ieee80211_iterate_active_interfaces_atomic - iterate active interfaces
5283 *
5284 * This function iterates over the interfaces associated with a given
5285 * hardware that are currently active and calls the callback for them.
5286 * This function requires the iterator callback function to be atomic,
5287 * if that is not desired, use @ieee80211_iterate_active_interfaces instead.
5288 * Does not iterate over a new interface during add_interface().
5289 *
5290 * @hw: the hardware struct of which the interfaces should be iterated over
5291 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
5292 * @iterator: the iterator function to call, cannot sleep
5293 * @data: first argument of the iterator function
5294 */
5295void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw,
5296 u32 iter_flags,
5297 void (*iterator)(void *data,
5298 u8 *mac,
5299 struct ieee80211_vif *vif),
5300 void *data);
5301
5302/**
5303 * ieee80211_iterate_active_interfaces_rtnl - iterate active interfaces
5304 *
5305 * This function iterates over the interfaces associated with a given
5306 * hardware that are currently active and calls the callback for them.
5307 * This version can only be used while holding the RTNL.
5308 *
5309 * @hw: the hardware struct of which the interfaces should be iterated over
5310 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
5311 * @iterator: the iterator function to call, cannot sleep
5312 * @data: first argument of the iterator function
5313 */
5314void ieee80211_iterate_active_interfaces_rtnl(struct ieee80211_hw *hw,
5315 u32 iter_flags,
5316 void (*iterator)(void *data,
5317 u8 *mac,
5318 struct ieee80211_vif *vif),
5319 void *data);
5320
5321/**
5322 * ieee80211_iterate_stations_atomic - iterate stations
5323 *
5324 * This function iterates over all stations associated with a given
5325 * hardware that are currently uploaded to the driver and calls the callback
5326 * function for them.
5327 * This function requires the iterator callback function to be atomic,
5328 *
5329 * @hw: the hardware struct of which the interfaces should be iterated over
5330 * @iterator: the iterator function to call, cannot sleep
5331 * @data: first argument of the iterator function
5332 */
5333void ieee80211_iterate_stations_atomic(struct ieee80211_hw *hw,
5334 void (*iterator)(void *data,
5335 struct ieee80211_sta *sta),
5336 void *data);
5337/**
5338 * ieee80211_queue_work - add work onto the mac80211 workqueue
5339 *
5340 * Drivers and mac80211 use this to add work onto the mac80211 workqueue.
5341 * This helper ensures drivers are not queueing work when they should not be.
5342 *
5343 * @hw: the hardware struct for the interface we are adding work for
5344 * @work: the work we want to add onto the mac80211 workqueue
5345 */
5346void ieee80211_queue_work(struct ieee80211_hw *hw, struct work_struct *work);
5347
5348/**
5349 * ieee80211_queue_delayed_work - add work onto the mac80211 workqueue
5350 *
5351 * Drivers and mac80211 use this to queue delayed work onto the mac80211
5352 * workqueue.
5353 *
5354 * @hw: the hardware struct for the interface we are adding work for
5355 * @dwork: delayable work to queue onto the mac80211 workqueue
5356 * @delay: number of jiffies to wait before queueing
5357 */
5358void ieee80211_queue_delayed_work(struct ieee80211_hw *hw,
5359 struct delayed_work *dwork,
5360 unsigned long delay);
5361
5362/**
5363 * ieee80211_start_tx_ba_session - Start a tx Block Ack session.
5364 * @sta: the station for which to start a BA session
5365 * @tid: the TID to BA on.
5366 * @timeout: session timeout value (in TUs)
5367 *
5368 * Return: success if addBA request was sent, failure otherwise
5369 *
5370 * Although mac80211/low level driver/user space application can estimate
5371 * the need to start aggregation on a certain RA/TID, the session level
5372 * will be managed by the mac80211.
5373 */
5374int ieee80211_start_tx_ba_session(struct ieee80211_sta *sta, u16 tid,
5375 u16 timeout);
5376
5377/**
5378 * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate.
5379 * @vif: &struct ieee80211_vif pointer from the add_interface callback
5380 * @ra: receiver address of the BA session recipient.
5381 * @tid: the TID to BA on.
5382 *
5383 * This function must be called by low level driver once it has
5384 * finished with preparations for the BA session. It can be called
5385 * from any context.
5386 */
5387void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
5388 u16 tid);
5389
5390/**
5391 * ieee80211_stop_tx_ba_session - Stop a Block Ack session.
5392 * @sta: the station whose BA session to stop
5393 * @tid: the TID to stop BA.
5394 *
5395 * Return: negative error if the TID is invalid, or no aggregation active
5396 *
5397 * Although mac80211/low level driver/user space application can estimate
5398 * the need to stop aggregation on a certain RA/TID, the session level
5399 * will be managed by the mac80211.
5400 */
5401int ieee80211_stop_tx_ba_session(struct ieee80211_sta *sta, u16 tid);
5402
5403/**
5404 * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate.
5405 * @vif: &struct ieee80211_vif pointer from the add_interface callback
5406 * @ra: receiver address of the BA session recipient.
5407 * @tid: the desired TID to BA on.
5408 *
5409 * This function must be called by low level driver once it has
5410 * finished with preparations for the BA session tear down. It
5411 * can be called from any context.
5412 */
5413void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
5414 u16 tid);
5415
5416/**
5417 * ieee80211_find_sta - find a station
5418 *
5419 * @vif: virtual interface to look for station on
5420 * @addr: station's address
5421 *
5422 * Return: The station, if found. %NULL otherwise.
5423 *
5424 * Note: This function must be called under RCU lock and the
5425 * resulting pointer is only valid under RCU lock as well.
5426 */
5427struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif,
5428 const u8 *addr);
5429
5430/**
5431 * ieee80211_find_sta_by_ifaddr - find a station on hardware
5432 *
5433 * @hw: pointer as obtained from ieee80211_alloc_hw()
5434 * @addr: remote station's address
5435 * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'.
5436 *
5437 * Return: The station, if found. %NULL otherwise.
5438 *
5439 * Note: This function must be called under RCU lock and the
5440 * resulting pointer is only valid under RCU lock as well.
5441 *
5442 * NOTE: You may pass NULL for localaddr, but then you will just get
5443 * the first STA that matches the remote address 'addr'.
5444 * We can have multiple STA associated with multiple
5445 * logical stations (e.g. consider a station connecting to another
5446 * BSSID on the same AP hardware without disconnecting first).
5447 * In this case, the result of this method with localaddr NULL
5448 * is not reliable.
5449 *
5450 * DO NOT USE THIS FUNCTION with localaddr NULL if at all possible.
5451 */
5452struct ieee80211_sta *ieee80211_find_sta_by_ifaddr(struct ieee80211_hw *hw,
5453 const u8 *addr,
5454 const u8 *localaddr);
5455
5456/**
5457 * ieee80211_sta_block_awake - block station from waking up
5458 * @hw: the hardware
5459 * @pubsta: the station
5460 * @block: whether to block or unblock
5461 *
5462 * Some devices require that all frames that are on the queues
5463 * for a specific station that went to sleep are flushed before
5464 * a poll response or frames after the station woke up can be
5465 * delivered to that it. Note that such frames must be rejected
5466 * by the driver as filtered, with the appropriate status flag.
5467 *
5468 * This function allows implementing this mode in a race-free
5469 * manner.
5470 *
5471 * To do this, a driver must keep track of the number of frames
5472 * still enqueued for a specific station. If this number is not
5473 * zero when the station goes to sleep, the driver must call
5474 * this function to force mac80211 to consider the station to
5475 * be asleep regardless of the station's actual state. Once the
5476 * number of outstanding frames reaches zero, the driver must
5477 * call this function again to unblock the station. That will
5478 * cause mac80211 to be able to send ps-poll responses, and if
5479 * the station queried in the meantime then frames will also
5480 * be sent out as a result of this. Additionally, the driver
5481 * will be notified that the station woke up some time after
5482 * it is unblocked, regardless of whether the station actually
5483 * woke up while blocked or not.
5484 */
5485void ieee80211_sta_block_awake(struct ieee80211_hw *hw,
5486 struct ieee80211_sta *pubsta, bool block);
5487
5488/**
5489 * ieee80211_sta_eosp - notify mac80211 about end of SP
5490 * @pubsta: the station
5491 *
5492 * When a device transmits frames in a way that it can't tell
5493 * mac80211 in the TX status about the EOSP, it must clear the
5494 * %IEEE80211_TX_STATUS_EOSP bit and call this function instead.
5495 * This applies for PS-Poll as well as uAPSD.
5496 *
5497 * Note that just like with _tx_status() and _rx() drivers must
5498 * not mix calls to irqsafe/non-irqsafe versions, this function
5499 * must not be mixed with those either. Use the all irqsafe, or
5500 * all non-irqsafe, don't mix!
5501 *
5502 * NB: the _irqsafe version of this function doesn't exist, no
5503 * driver needs it right now. Don't call this function if
5504 * you'd need the _irqsafe version, look at the git history
5505 * and restore the _irqsafe version!
5506 */
5507void ieee80211_sta_eosp(struct ieee80211_sta *pubsta);
5508
5509/**
5510 * ieee80211_send_eosp_nullfunc - ask mac80211 to send NDP with EOSP
5511 * @pubsta: the station
5512 * @tid: the tid of the NDP
5513 *
5514 * Sometimes the device understands that it needs to close
5515 * the Service Period unexpectedly. This can happen when
5516 * sending frames that are filling holes in the BA window.
5517 * In this case, the device can ask mac80211 to send a
5518 * Nullfunc frame with EOSP set. When that happens, the
5519 * driver must have called ieee80211_sta_set_buffered() to
5520 * let mac80211 know that there are no buffered frames any
5521 * more, otherwise mac80211 will get the more_data bit wrong.
5522 * The low level driver must have made sure that the frame
5523 * will be sent despite the station being in power-save.
5524 * Mac80211 won't call allow_buffered_frames().
5525 * Note that calling this function, doesn't exempt the driver
5526 * from closing the EOSP properly, it will still have to call
5527 * ieee80211_sta_eosp when the NDP is sent.
5528 */
5529void ieee80211_send_eosp_nullfunc(struct ieee80211_sta *pubsta, int tid);
5530
5531/**
5532 * ieee80211_sta_register_airtime - register airtime usage for a sta/tid
5533 *
5534 * Register airtime usage for a given sta on a given tid. The driver can call
5535 * this function to notify mac80211 that a station used a certain amount of
5536 * airtime. This information will be used by the TXQ scheduler to schedule
5537 * stations in a way that ensures airtime fairness.
5538 *
5539 * The reported airtime should as a minimum include all time that is spent
5540 * transmitting to the remote station, including overhead and padding, but not
5541 * including time spent waiting for a TXOP. If the time is not reported by the
5542 * hardware it can in some cases be calculated from the rate and known frame
5543 * composition. When possible, the time should include any failed transmission
5544 * attempts.
5545 *
5546 * The driver can either call this function synchronously for every packet or
5547 * aggregate, or asynchronously as airtime usage information becomes available.
5548 * TX and RX airtime can be reported together, or separately by setting one of
5549 * them to 0.
5550 *
5551 * @pubsta: the station
5552 * @tid: the TID to register airtime for
5553 * @tx_airtime: airtime used during TX (in usec)
5554 * @rx_airtime: airtime used during RX (in usec)
5555 */
5556void ieee80211_sta_register_airtime(struct ieee80211_sta *pubsta, u8 tid,
5557 u32 tx_airtime, u32 rx_airtime);
5558
5559/**
5560 * ieee80211_iter_keys - iterate keys programmed into the device
5561 * @hw: pointer obtained from ieee80211_alloc_hw()
5562 * @vif: virtual interface to iterate, may be %NULL for all
5563 * @iter: iterator function that will be called for each key
5564 * @iter_data: custom data to pass to the iterator function
5565 *
5566 * This function can be used to iterate all the keys known to
5567 * mac80211, even those that weren't previously programmed into
5568 * the device. This is intended for use in WoWLAN if the device
5569 * needs reprogramming of the keys during suspend. Note that due
5570 * to locking reasons, it is also only safe to call this at few
5571 * spots since it must hold the RTNL and be able to sleep.
5572 *
5573 * The order in which the keys are iterated matches the order
5574 * in which they were originally installed and handed to the
5575 * set_key callback.
5576 */
5577void ieee80211_iter_keys(struct ieee80211_hw *hw,
5578 struct ieee80211_vif *vif,
5579 void (*iter)(struct ieee80211_hw *hw,
5580 struct ieee80211_vif *vif,
5581 struct ieee80211_sta *sta,
5582 struct ieee80211_key_conf *key,
5583 void *data),
5584 void *iter_data);
5585
5586/**
5587 * ieee80211_iter_keys_rcu - iterate keys programmed into the device
5588 * @hw: pointer obtained from ieee80211_alloc_hw()
5589 * @vif: virtual interface to iterate, may be %NULL for all
5590 * @iter: iterator function that will be called for each key
5591 * @iter_data: custom data to pass to the iterator function
5592 *
5593 * This function can be used to iterate all the keys known to
5594 * mac80211, even those that weren't previously programmed into
5595 * the device. Note that due to locking reasons, keys of station
5596 * in removal process will be skipped.
5597 *
5598 * This function requires being called in an RCU critical section,
5599 * and thus iter must be atomic.
5600 */
5601void ieee80211_iter_keys_rcu(struct ieee80211_hw *hw,
5602 struct ieee80211_vif *vif,
5603 void (*iter)(struct ieee80211_hw *hw,
5604 struct ieee80211_vif *vif,
5605 struct ieee80211_sta *sta,
5606 struct ieee80211_key_conf *key,
5607 void *data),
5608 void *iter_data);
5609
5610/**
5611 * ieee80211_iter_chan_contexts_atomic - iterate channel contexts
5612 * @hw: pointre obtained from ieee80211_alloc_hw().
5613 * @iter: iterator function
5614 * @iter_data: data passed to iterator function
5615 *
5616 * Iterate all active channel contexts. This function is atomic and
5617 * doesn't acquire any locks internally that might be held in other
5618 * places while calling into the driver.
5619 *
5620 * The iterator will not find a context that's being added (during
5621 * the driver callback to add it) but will find it while it's being
5622 * removed.
5623 *
5624 * Note that during hardware restart, all contexts that existed
5625 * before the restart are considered already present so will be
5626 * found while iterating, whether they've been re-added already
5627 * or not.
5628 */
5629void ieee80211_iter_chan_contexts_atomic(
5630 struct ieee80211_hw *hw,
5631 void (*iter)(struct ieee80211_hw *hw,
5632 struct ieee80211_chanctx_conf *chanctx_conf,
5633 void *data),
5634 void *iter_data);
5635
5636/**
5637 * ieee80211_ap_probereq_get - retrieve a Probe Request template
5638 * @hw: pointer obtained from ieee80211_alloc_hw().
5639 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5640 *
5641 * Creates a Probe Request template which can, for example, be uploaded to
5642 * hardware. The template is filled with bssid, ssid and supported rate
5643 * information. This function must only be called from within the
5644 * .bss_info_changed callback function and only in managed mode. The function
5645 * is only useful when the interface is associated, otherwise it will return
5646 * %NULL.
5647 *
5648 * Return: The Probe Request template. %NULL on error.
5649 */
5650struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw,
5651 struct ieee80211_vif *vif);
5652
5653/**
5654 * ieee80211_beacon_loss - inform hardware does not receive beacons
5655 *
5656 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5657 *
5658 * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER and
5659 * %IEEE80211_CONF_PS is set, the driver needs to inform whenever the
5660 * hardware is not receiving beacons with this function.
5661 */
5662void ieee80211_beacon_loss(struct ieee80211_vif *vif);
5663
5664/**
5665 * ieee80211_connection_loss - inform hardware has lost connection to the AP
5666 *
5667 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5668 *
5669 * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER, and
5670 * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver
5671 * needs to inform if the connection to the AP has been lost.
5672 * The function may also be called if the connection needs to be terminated
5673 * for some other reason, even if %IEEE80211_HW_CONNECTION_MONITOR isn't set.
5674 *
5675 * This function will cause immediate change to disassociated state,
5676 * without connection recovery attempts.
5677 */
5678void ieee80211_connection_loss(struct ieee80211_vif *vif);
5679
5680/**
5681 * ieee80211_resume_disconnect - disconnect from AP after resume
5682 *
5683 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5684 *
5685 * Instructs mac80211 to disconnect from the AP after resume.
5686 * Drivers can use this after WoWLAN if they know that the
5687 * connection cannot be kept up, for example because keys were
5688 * used while the device was asleep but the replay counters or
5689 * similar cannot be retrieved from the device during resume.
5690 *
5691 * Note that due to implementation issues, if the driver uses
5692 * the reconfiguration functionality during resume the interface
5693 * will still be added as associated first during resume and then
5694 * disconnect normally later.
5695 *
5696 * This function can only be called from the resume callback and
5697 * the driver must not be holding any of its own locks while it
5698 * calls this function, or at least not any locks it needs in the
5699 * key configuration paths (if it supports HW crypto).
5700 */
5701void ieee80211_resume_disconnect(struct ieee80211_vif *vif);
5702
5703/**
5704 * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring
5705 * rssi threshold triggered
5706 *
5707 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5708 * @rssi_event: the RSSI trigger event type
5709 * @rssi_level: new RSSI level value or 0 if not available
5710 * @gfp: context flags
5711 *
5712 * When the %IEEE80211_VIF_SUPPORTS_CQM_RSSI is set, and a connection quality
5713 * monitoring is configured with an rssi threshold, the driver will inform
5714 * whenever the rssi level reaches the threshold.
5715 */
5716void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif,
5717 enum nl80211_cqm_rssi_threshold_event rssi_event,
5718 s32 rssi_level,
5719 gfp_t gfp);
5720
5721/**
5722 * ieee80211_cqm_beacon_loss_notify - inform CQM of beacon loss
5723 *
5724 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5725 * @gfp: context flags
5726 */
5727void ieee80211_cqm_beacon_loss_notify(struct ieee80211_vif *vif, gfp_t gfp);
5728
5729/**
5730 * ieee80211_radar_detected - inform that a radar was detected
5731 *
5732 * @hw: pointer as obtained from ieee80211_alloc_hw()
5733 */
5734void ieee80211_radar_detected(struct ieee80211_hw *hw);
5735
5736/**
5737 * ieee80211_chswitch_done - Complete channel switch process
5738 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5739 * @success: make the channel switch successful or not
5740 *
5741 * Complete the channel switch post-process: set the new operational channel
5742 * and wake up the suspended queues.
5743 */
5744void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success);
5745
5746/**
5747 * ieee80211_request_smps - request SM PS transition
5748 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5749 * @smps_mode: new SM PS mode
5750 *
5751 * This allows the driver to request an SM PS transition in managed
5752 * mode. This is useful when the driver has more information than
5753 * the stack about possible interference, for example by bluetooth.
5754 */
5755void ieee80211_request_smps(struct ieee80211_vif *vif,
5756 enum ieee80211_smps_mode smps_mode);
5757
5758/**
5759 * ieee80211_ready_on_channel - notification of remain-on-channel start
5760 * @hw: pointer as obtained from ieee80211_alloc_hw()
5761 */
5762void ieee80211_ready_on_channel(struct ieee80211_hw *hw);
5763
5764/**
5765 * ieee80211_remain_on_channel_expired - remain_on_channel duration expired
5766 * @hw: pointer as obtained from ieee80211_alloc_hw()
5767 */
5768void ieee80211_remain_on_channel_expired(struct ieee80211_hw *hw);
5769
5770/**
5771 * ieee80211_stop_rx_ba_session - callback to stop existing BA sessions
5772 *
5773 * in order not to harm the system performance and user experience, the device
5774 * may request not to allow any rx ba session and tear down existing rx ba
5775 * sessions based on system constraints such as periodic BT activity that needs
5776 * to limit wlan activity (eg.sco or a2dp)."
5777 * in such cases, the intention is to limit the duration of the rx ppdu and
5778 * therefore prevent the peer device to use a-mpdu aggregation.
5779 *
5780 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5781 * @ba_rx_bitmap: Bit map of open rx ba per tid
5782 * @addr: & to bssid mac address
5783 */
5784void ieee80211_stop_rx_ba_session(struct ieee80211_vif *vif, u16 ba_rx_bitmap,
5785 const u8 *addr);
5786
5787/**
5788 * ieee80211_mark_rx_ba_filtered_frames - move RX BA window and mark filtered
5789 * @pubsta: station struct
5790 * @tid: the session's TID
5791 * @ssn: starting sequence number of the bitmap, all frames before this are
5792 * assumed to be out of the window after the call
5793 * @filtered: bitmap of filtered frames, BIT(0) is the @ssn entry etc.
5794 * @received_mpdus: number of received mpdus in firmware
5795 *
5796 * This function moves the BA window and releases all frames before @ssn, and
5797 * marks frames marked in the bitmap as having been filtered. Afterwards, it
5798 * checks if any frames in the window starting from @ssn can now be released
5799 * (in case they were only waiting for frames that were filtered.)
5800 */
5801void ieee80211_mark_rx_ba_filtered_frames(struct ieee80211_sta *pubsta, u8 tid,
5802 u16 ssn, u64 filtered,
5803 u16 received_mpdus);
5804
5805/**
5806 * ieee80211_send_bar - send a BlockAckReq frame
5807 *
5808 * can be used to flush pending frames from the peer's aggregation reorder
5809 * buffer.
5810 *
5811 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
5812 * @ra: the peer's destination address
5813 * @tid: the TID of the aggregation session
5814 * @ssn: the new starting sequence number for the receiver
5815 */
5816void ieee80211_send_bar(struct ieee80211_vif *vif, u8 *ra, u16 tid, u16 ssn);
5817
5818/**
5819 * ieee80211_manage_rx_ba_offl - helper to queue an RX BA work
5820 * @vif: &struct ieee80211_vif pointer from the add_interface callback
5821 * @addr: station mac address
5822 * @tid: the rx tid
5823 */
5824void ieee80211_manage_rx_ba_offl(struct ieee80211_vif *vif, const u8 *addr,
5825 unsigned int tid);
5826
5827/**
5828 * ieee80211_start_rx_ba_session_offl - start a Rx BA session
5829 *
5830 * Some device drivers may offload part of the Rx aggregation flow including
5831 * AddBa/DelBa negotiation but may otherwise be incapable of full Rx
5832 * reordering.
5833 *
5834 * Create structures responsible for reordering so device drivers may call here
5835 * when they complete AddBa negotiation.
5836 *
5837 * @vif: &struct ieee80211_vif pointer from the add_interface callback
5838 * @addr: station mac address
5839 * @tid: the rx tid
5840 */
5841static inline void ieee80211_start_rx_ba_session_offl(struct ieee80211_vif *vif,
5842 const u8 *addr, u16 tid)
5843{
5844 if (WARN_ON(tid >= IEEE80211_NUM_TIDS))
5845 return;
5846 ieee80211_manage_rx_ba_offl(vif, addr, tid);
5847}
5848
5849/**
5850 * ieee80211_stop_rx_ba_session_offl - stop a Rx BA session
5851 *
5852 * Some device drivers may offload part of the Rx aggregation flow including
5853 * AddBa/DelBa negotiation but may otherwise be incapable of full Rx
5854 * reordering.
5855 *
5856 * Destroy structures responsible for reordering so device drivers may call here
5857 * when they complete DelBa negotiation.
5858 *
5859 * @vif: &struct ieee80211_vif pointer from the add_interface callback
5860 * @addr: station mac address
5861 * @tid: the rx tid
5862 */
5863static inline void ieee80211_stop_rx_ba_session_offl(struct ieee80211_vif *vif,
5864 const u8 *addr, u16 tid)
5865{
5866 if (WARN_ON(tid >= IEEE80211_NUM_TIDS))
5867 return;
5868 ieee80211_manage_rx_ba_offl(vif, addr, tid + IEEE80211_NUM_TIDS);
5869}
5870
5871/**
5872 * ieee80211_rx_ba_timer_expired - stop a Rx BA session due to timeout
5873 *
5874 * Some device drivers do not offload AddBa/DelBa negotiation, but handle rx
5875 * buffer reording internally, and therefore also handle the session timer.
5876 *
5877 * Trigger the timeout flow, which sends a DelBa.
5878 *
5879 * @vif: &struct ieee80211_vif pointer from the add_interface callback
5880 * @addr: station mac address
5881 * @tid: the rx tid
5882 */
5883void ieee80211_rx_ba_timer_expired(struct ieee80211_vif *vif,
5884 const u8 *addr, unsigned int tid);
5885
5886/* Rate control API */
5887
5888/**
5889 * struct ieee80211_tx_rate_control - rate control information for/from RC algo
5890 *
5891 * @hw: The hardware the algorithm is invoked for.
5892 * @sband: The band this frame is being transmitted on.
5893 * @bss_conf: the current BSS configuration
5894 * @skb: the skb that will be transmitted, the control information in it needs
5895 * to be filled in
5896 * @reported_rate: The rate control algorithm can fill this in to indicate
5897 * which rate should be reported to userspace as the current rate and
5898 * used for rate calculations in the mesh network.
5899 * @rts: whether RTS will be used for this frame because it is longer than the
5900 * RTS threshold
5901 * @short_preamble: whether mac80211 will request short-preamble transmission
5902 * if the selected rate supports it
5903 * @rate_idx_mask: user-requested (legacy) rate mask
5904 * @rate_idx_mcs_mask: user-requested MCS rate mask (NULL if not in use)
5905 * @bss: whether this frame is sent out in AP or IBSS mode
5906 */
5907struct ieee80211_tx_rate_control {
5908 struct ieee80211_hw *hw;
5909 struct ieee80211_supported_band *sband;
5910 struct ieee80211_bss_conf *bss_conf;
5911 struct sk_buff *skb;
5912 struct ieee80211_tx_rate reported_rate;
5913 bool rts, short_preamble;
5914 u32 rate_idx_mask;
5915 u8 *rate_idx_mcs_mask;
5916 bool bss;
5917};
5918
5919/**
5920 * enum rate_control_capabilities - rate control capabilities
5921 */
5922enum rate_control_capabilities {
5923 /**
5924 * @RATE_CTRL_CAPA_VHT_EXT_NSS_BW:
5925 * Support for extended NSS BW support (dot11VHTExtendedNSSCapable)
5926 * Note that this is only looked at if the minimum number of chains
5927 * that the AP uses is < the number of TX chains the hardware has,
5928 * otherwise the NSS difference doesn't bother us.
5929 */
5930 RATE_CTRL_CAPA_VHT_EXT_NSS_BW = BIT(0),
5931};
5932
5933struct rate_control_ops {
5934 unsigned long capa;
5935 const char *name;
5936 void *(*alloc)(struct ieee80211_hw *hw, struct dentry *debugfsdir);
5937 void (*free)(void *priv);
5938
5939 void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp);
5940 void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
5941 struct cfg80211_chan_def *chandef,
5942 struct ieee80211_sta *sta, void *priv_sta);
5943 void (*rate_update)(void *priv, struct ieee80211_supported_band *sband,
5944 struct cfg80211_chan_def *chandef,
5945 struct ieee80211_sta *sta, void *priv_sta,
5946 u32 changed);
5947 void (*free_sta)(void *priv, struct ieee80211_sta *sta,
5948 void *priv_sta);
5949
5950 void (*tx_status_ext)(void *priv,
5951 struct ieee80211_supported_band *sband,
5952 void *priv_sta, struct ieee80211_tx_status *st);
5953 void (*tx_status)(void *priv, struct ieee80211_supported_band *sband,
5954 struct ieee80211_sta *sta, void *priv_sta,
5955 struct sk_buff *skb);
5956 void (*get_rate)(void *priv, struct ieee80211_sta *sta, void *priv_sta,
5957 struct ieee80211_tx_rate_control *txrc);
5958
5959 void (*add_sta_debugfs)(void *priv, void *priv_sta,
5960 struct dentry *dir);
5961
5962 u32 (*get_expected_throughput)(void *priv_sta);
5963};
5964
5965static inline int rate_supported(struct ieee80211_sta *sta,
5966 enum nl80211_band band,
5967 int index)
5968{
5969 return (sta == NULL || sta->supp_rates[band] & BIT(index));
5970}
5971
5972static inline s8
5973rate_lowest_index(struct ieee80211_supported_band *sband,
5974 struct ieee80211_sta *sta)
5975{
5976 int i;
5977
5978 for (i = 0; i < sband->n_bitrates; i++)
5979 if (rate_supported(sta, sband->band, i))
5980 return i;
5981
5982 /* warn when we cannot find a rate. */
5983 WARN_ON_ONCE(1);
5984
5985 /* and return 0 (the lowest index) */
5986 return 0;
5987}
5988
5989static inline
5990bool rate_usable_index_exists(struct ieee80211_supported_band *sband,
5991 struct ieee80211_sta *sta)
5992{
5993 unsigned int i;
5994
5995 for (i = 0; i < sband->n_bitrates; i++)
5996 if (rate_supported(sta, sband->band, i))
5997 return true;
5998 return false;
5999}
6000
6001/**
6002 * rate_control_set_rates - pass the sta rate selection to mac80211/driver
6003 *
6004 * When not doing a rate control probe to test rates, rate control should pass
6005 * its rate selection to mac80211. If the driver supports receiving a station
6006 * rate table, it will use it to ensure that frames are always sent based on
6007 * the most recent rate control module decision.
6008 *
6009 * @hw: pointer as obtained from ieee80211_alloc_hw()
6010 * @pubsta: &struct ieee80211_sta pointer to the target destination.
6011 * @rates: new tx rate set to be used for this station.
6012 */
6013int rate_control_set_rates(struct ieee80211_hw *hw,
6014 struct ieee80211_sta *pubsta,
6015 struct ieee80211_sta_rates *rates);
6016
6017int ieee80211_rate_control_register(const struct rate_control_ops *ops);
6018void ieee80211_rate_control_unregister(const struct rate_control_ops *ops);
6019
6020static inline bool
6021conf_is_ht20(struct ieee80211_conf *conf)
6022{
6023 return conf->chandef.width == NL80211_CHAN_WIDTH_20;
6024}
6025
6026static inline bool
6027conf_is_ht40_minus(struct ieee80211_conf *conf)
6028{
6029 return conf->chandef.width == NL80211_CHAN_WIDTH_40 &&
6030 conf->chandef.center_freq1 < conf->chandef.chan->center_freq;
6031}
6032
6033static inline bool
6034conf_is_ht40_plus(struct ieee80211_conf *conf)
6035{
6036 return conf->chandef.width == NL80211_CHAN_WIDTH_40 &&
6037 conf->chandef.center_freq1 > conf->chandef.chan->center_freq;
6038}
6039
6040static inline bool
6041conf_is_ht40(struct ieee80211_conf *conf)
6042{
6043 return conf->chandef.width == NL80211_CHAN_WIDTH_40;
6044}
6045
6046static inline bool
6047conf_is_ht(struct ieee80211_conf *conf)
6048{
6049 return (conf->chandef.width != NL80211_CHAN_WIDTH_5) &&
6050 (conf->chandef.width != NL80211_CHAN_WIDTH_10) &&
6051 (conf->chandef.width != NL80211_CHAN_WIDTH_20_NOHT);
6052}
6053
6054static inline enum nl80211_iftype
6055ieee80211_iftype_p2p(enum nl80211_iftype type, bool p2p)
6056{
6057 if (p2p) {
6058 switch (type) {
6059 case NL80211_IFTYPE_STATION:
6060 return NL80211_IFTYPE_P2P_CLIENT;
6061 case NL80211_IFTYPE_AP:
6062 return NL80211_IFTYPE_P2P_GO;
6063 default:
6064 break;
6065 }
6066 }
6067 return type;
6068}
6069
6070static inline enum nl80211_iftype
6071ieee80211_vif_type_p2p(struct ieee80211_vif *vif)
6072{
6073 return ieee80211_iftype_p2p(vif->type, vif->p2p);
6074}
6075
6076/**
6077 * ieee80211_update_mu_groups - set the VHT MU-MIMO groud data
6078 *
6079 * @vif: the specified virtual interface
6080 * @membership: 64 bits array - a bit is set if station is member of the group
6081 * @position: 2 bits per group id indicating the position in the group
6082 *
6083 * Note: This function assumes that the given vif is valid and the position and
6084 * membership data is of the correct size and are in the same byte order as the
6085 * matching GroupId management frame.
6086 * Calls to this function need to be serialized with RX path.
6087 */
6088void ieee80211_update_mu_groups(struct ieee80211_vif *vif,
6089 const u8 *membership, const u8 *position);
6090
6091void ieee80211_enable_rssi_reports(struct ieee80211_vif *vif,
6092 int rssi_min_thold,
6093 int rssi_max_thold);
6094
6095void ieee80211_disable_rssi_reports(struct ieee80211_vif *vif);
6096
6097/**
6098 * ieee80211_ave_rssi - report the average RSSI for the specified interface
6099 *
6100 * @vif: the specified virtual interface
6101 *
6102 * Note: This function assumes that the given vif is valid.
6103 *
6104 * Return: The average RSSI value for the requested interface, or 0 if not
6105 * applicable.
6106 */
6107int ieee80211_ave_rssi(struct ieee80211_vif *vif);
6108
6109/**
6110 * ieee80211_report_wowlan_wakeup - report WoWLAN wakeup
6111 * @vif: virtual interface
6112 * @wakeup: wakeup reason(s)
6113 * @gfp: allocation flags
6114 *
6115 * See cfg80211_report_wowlan_wakeup().
6116 */
6117void ieee80211_report_wowlan_wakeup(struct ieee80211_vif *vif,
6118 struct cfg80211_wowlan_wakeup *wakeup,
6119 gfp_t gfp);
6120
6121/**
6122 * ieee80211_tx_prepare_skb - prepare an 802.11 skb for transmission
6123 * @hw: pointer as obtained from ieee80211_alloc_hw()
6124 * @vif: virtual interface
6125 * @skb: frame to be sent from within the driver
6126 * @band: the band to transmit on
6127 * @sta: optional pointer to get the station to send the frame to
6128 *
6129 * Note: must be called under RCU lock
6130 */
6131bool ieee80211_tx_prepare_skb(struct ieee80211_hw *hw,
6132 struct ieee80211_vif *vif, struct sk_buff *skb,
6133 int band, struct ieee80211_sta **sta);
6134
6135/**
6136 * struct ieee80211_noa_data - holds temporary data for tracking P2P NoA state
6137 *
6138 * @next_tsf: TSF timestamp of the next absent state change
6139 * @has_next_tsf: next absent state change event pending
6140 *
6141 * @absent: descriptor bitmask, set if GO is currently absent
6142 *
6143 * private:
6144 *
6145 * @count: count fields from the NoA descriptors
6146 * @desc: adjusted data from the NoA
6147 */
6148struct ieee80211_noa_data {
6149 u32 next_tsf;
6150 bool has_next_tsf;
6151
6152 u8 absent;
6153
6154 u8 count[IEEE80211_P2P_NOA_DESC_MAX];
6155 struct {
6156 u32 start;
6157 u32 duration;
6158 u32 interval;
6159 } desc[IEEE80211_P2P_NOA_DESC_MAX];
6160};
6161
6162/**
6163 * ieee80211_parse_p2p_noa - initialize NoA tracking data from P2P IE
6164 *
6165 * @attr: P2P NoA IE
6166 * @data: NoA tracking data
6167 * @tsf: current TSF timestamp
6168 *
6169 * Return: number of successfully parsed descriptors
6170 */
6171int ieee80211_parse_p2p_noa(const struct ieee80211_p2p_noa_attr *attr,
6172 struct ieee80211_noa_data *data, u32 tsf);
6173
6174/**
6175 * ieee80211_update_p2p_noa - get next pending P2P GO absent state change
6176 *
6177 * @data: NoA tracking data
6178 * @tsf: current TSF timestamp
6179 */
6180void ieee80211_update_p2p_noa(struct ieee80211_noa_data *data, u32 tsf);
6181
6182/**
6183 * ieee80211_tdls_oper - request userspace to perform a TDLS operation
6184 * @vif: virtual interface
6185 * @peer: the peer's destination address
6186 * @oper: the requested TDLS operation
6187 * @reason_code: reason code for the operation, valid for TDLS teardown
6188 * @gfp: allocation flags
6189 *
6190 * See cfg80211_tdls_oper_request().
6191 */
6192void ieee80211_tdls_oper_request(struct ieee80211_vif *vif, const u8 *peer,
6193 enum nl80211_tdls_operation oper,
6194 u16 reason_code, gfp_t gfp);
6195
6196/**
6197 * ieee80211_reserve_tid - request to reserve a specific TID
6198 *
6199 * There is sometimes a need (such as in TDLS) for blocking the driver from
6200 * using a specific TID so that the FW can use it for certain operations such
6201 * as sending PTI requests. To make sure that the driver doesn't use that TID,
6202 * this function must be called as it flushes out packets on this TID and marks
6203 * it as blocked, so that any transmit for the station on this TID will be
6204 * redirected to the alternative TID in the same AC.
6205 *
6206 * Note that this function blocks and may call back into the driver, so it
6207 * should be called without driver locks held. Also note this function should
6208 * only be called from the driver's @sta_state callback.
6209 *
6210 * @sta: the station to reserve the TID for
6211 * @tid: the TID to reserve
6212 *
6213 * Returns: 0 on success, else on failure
6214 */
6215int ieee80211_reserve_tid(struct ieee80211_sta *sta, u8 tid);
6216
6217/**
6218 * ieee80211_unreserve_tid - request to unreserve a specific TID
6219 *
6220 * Once there is no longer any need for reserving a certain TID, this function
6221 * should be called, and no longer will packets have their TID modified for
6222 * preventing use of this TID in the driver.
6223 *
6224 * Note that this function blocks and acquires a lock, so it should be called
6225 * without driver locks held. Also note this function should only be called
6226 * from the driver's @sta_state callback.
6227 *
6228 * @sta: the station
6229 * @tid: the TID to unreserve
6230 */
6231void ieee80211_unreserve_tid(struct ieee80211_sta *sta, u8 tid);
6232
6233/**
6234 * ieee80211_tx_dequeue - dequeue a packet from a software tx queue
6235 *
6236 * @hw: pointer as obtained from ieee80211_alloc_hw()
6237 * @txq: pointer obtained from station or virtual interface, or from
6238 * ieee80211_next_txq()
6239 *
6240 * Returns the skb if successful, %NULL if no frame was available.
6241 *
6242 * Note that this must be called in an rcu_read_lock() critical section,
6243 * which can only be released after the SKB was handled. Some pointers in
6244 * skb->cb, e.g. the key pointer, are protected by by RCU and thus the
6245 * critical section must persist not just for the duration of this call
6246 * but for the duration of the frame handling.
6247 * However, also note that while in the wake_tx_queue() method,
6248 * rcu_read_lock() is already held.
6249 *
6250 * softirqs must also be disabled when this function is called.
6251 * In process context, use ieee80211_tx_dequeue_ni() instead.
6252 */
6253struct sk_buff *ieee80211_tx_dequeue(struct ieee80211_hw *hw,
6254 struct ieee80211_txq *txq);
6255
6256/**
6257 * ieee80211_tx_dequeue_ni - dequeue a packet from a software tx queue
6258 * (in process context)
6259 *
6260 * Like ieee80211_tx_dequeue() but can be called in process context
6261 * (internally disables bottom halves).
6262 *
6263 * @hw: pointer as obtained from ieee80211_alloc_hw()
6264 * @txq: pointer obtained from station or virtual interface, or from
6265 * ieee80211_next_txq()
6266 */
6267static inline struct sk_buff *ieee80211_tx_dequeue_ni(struct ieee80211_hw *hw,
6268 struct ieee80211_txq *txq)
6269{
6270 struct sk_buff *skb;
6271
6272 local_bh_disable();
6273 skb = ieee80211_tx_dequeue(hw, txq);
6274 local_bh_enable();
6275
6276 return skb;
6277}
6278
6279/**
6280 * ieee80211_next_txq - get next tx queue to pull packets from
6281 *
6282 * @hw: pointer as obtained from ieee80211_alloc_hw()
6283 * @ac: AC number to return packets from.
6284 *
6285 * Returns the next txq if successful, %NULL if no queue is eligible. If a txq
6286 * is returned, it should be returned with ieee80211_return_txq() after the
6287 * driver has finished scheduling it.
6288 */
6289struct ieee80211_txq *ieee80211_next_txq(struct ieee80211_hw *hw, u8 ac);
6290
6291/**
6292 * ieee80211_txq_schedule_start - start new scheduling round for TXQs
6293 *
6294 * @hw: pointer as obtained from ieee80211_alloc_hw()
6295 * @ac: AC number to acquire locks for
6296 *
6297 * Should be called before ieee80211_next_txq() or ieee80211_return_txq().
6298 * The driver must not call multiple TXQ scheduling rounds concurrently.
6299 */
6300void ieee80211_txq_schedule_start(struct ieee80211_hw *hw, u8 ac);
6301
6302/* (deprecated) */
6303static inline void ieee80211_txq_schedule_end(struct ieee80211_hw *hw, u8 ac)
6304{
6305}
6306
6307void __ieee80211_schedule_txq(struct ieee80211_hw *hw,
6308 struct ieee80211_txq *txq, bool force);
6309
6310/**
6311 * ieee80211_schedule_txq - schedule a TXQ for transmission
6312 *
6313 * @hw: pointer as obtained from ieee80211_alloc_hw()
6314 * @txq: pointer obtained from station or virtual interface
6315 *
6316 * Schedules a TXQ for transmission if it is not already scheduled,
6317 * even if mac80211 does not have any packets buffered.
6318 *
6319 * The driver may call this function if it has buffered packets for
6320 * this TXQ internally.
6321 */
6322static inline void
6323ieee80211_schedule_txq(struct ieee80211_hw *hw, struct ieee80211_txq *txq)
6324{
6325 __ieee80211_schedule_txq(hw, txq, true);
6326}
6327
6328/**
6329 * ieee80211_return_txq - return a TXQ previously acquired by ieee80211_next_txq()
6330 *
6331 * @hw: pointer as obtained from ieee80211_alloc_hw()
6332 * @txq: pointer obtained from station or virtual interface
6333 * @force: schedule txq even if mac80211 does not have any buffered packets.
6334 *
6335 * The driver may set force=true if it has buffered packets for this TXQ
6336 * internally.
6337 */
6338static inline void
6339ieee80211_return_txq(struct ieee80211_hw *hw, struct ieee80211_txq *txq,
6340 bool force)
6341{
6342 __ieee80211_schedule_txq(hw, txq, force);
6343}
6344
6345/**
6346 * ieee80211_txq_may_transmit - check whether TXQ is allowed to transmit
6347 *
6348 * This function is used to check whether given txq is allowed to transmit by
6349 * the airtime scheduler, and can be used by drivers to access the airtime
6350 * fairness accounting without going using the scheduling order enfored by
6351 * next_txq().
6352 *
6353 * Returns %true if the airtime scheduler thinks the TXQ should be allowed to
6354 * transmit, and %false if it should be throttled. This function can also have
6355 * the side effect of rotating the TXQ in the scheduler rotation, which will
6356 * eventually bring the deficit to positive and allow the station to transmit
6357 * again.
6358 *
6359 * The API ieee80211_txq_may_transmit() also ensures that TXQ list will be
6360 * aligned aginst driver's own round-robin scheduler list. i.e it rotates
6361 * the TXQ list till it makes the requested node becomes the first entry
6362 * in TXQ list. Thus both the TXQ list and driver's list are in sync. If this
6363 * function returns %true, the driver is expected to schedule packets
6364 * for transmission, and then return the TXQ through ieee80211_return_txq().
6365 *
6366 * @hw: pointer as obtained from ieee80211_alloc_hw()
6367 * @txq: pointer obtained from station or virtual interface
6368 */
6369bool ieee80211_txq_may_transmit(struct ieee80211_hw *hw,
6370 struct ieee80211_txq *txq);
6371
6372/**
6373 * ieee80211_txq_get_depth - get pending frame/byte count of given txq
6374 *
6375 * The values are not guaranteed to be coherent with regard to each other, i.e.
6376 * txq state can change half-way of this function and the caller may end up
6377 * with "new" frame_cnt and "old" byte_cnt or vice-versa.
6378 *
6379 * @txq: pointer obtained from station or virtual interface
6380 * @frame_cnt: pointer to store frame count
6381 * @byte_cnt: pointer to store byte count
6382 */
6383void ieee80211_txq_get_depth(struct ieee80211_txq *txq,
6384 unsigned long *frame_cnt,
6385 unsigned long *byte_cnt);
6386
6387/**
6388 * ieee80211_nan_func_terminated - notify about NAN function termination.
6389 *
6390 * This function is used to notify mac80211 about NAN function termination.
6391 * Note that this function can't be called from hard irq.
6392 *
6393 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6394 * @inst_id: the local instance id
6395 * @reason: termination reason (one of the NL80211_NAN_FUNC_TERM_REASON_*)
6396 * @gfp: allocation flags
6397 */
6398void ieee80211_nan_func_terminated(struct ieee80211_vif *vif,
6399 u8 inst_id,
6400 enum nl80211_nan_func_term_reason reason,
6401 gfp_t gfp);
6402
6403/**
6404 * ieee80211_nan_func_match - notify about NAN function match event.
6405 *
6406 * This function is used to notify mac80211 about NAN function match. The
6407 * cookie inside the match struct will be assigned by mac80211.
6408 * Note that this function can't be called from hard irq.
6409 *
6410 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
6411 * @match: match event information
6412 * @gfp: allocation flags
6413 */
6414void ieee80211_nan_func_match(struct ieee80211_vif *vif,
6415 struct cfg80211_nan_match_params *match,
6416 gfp_t gfp);
6417
6418#endif /* MAC80211_H */
1/*
2 * mac80211 <-> driver interface
3 *
4 * Copyright 2002-2005, Devicescape Software, Inc.
5 * Copyright 2006-2007 Jiri Benc <jbenc@suse.cz>
6 * Copyright 2007-2010 Johannes Berg <johannes@sipsolutions.net>
7 *
8 * This program is free software; you can redistribute it and/or modify
9 * it under the terms of the GNU General Public License version 2 as
10 * published by the Free Software Foundation.
11 */
12
13#ifndef MAC80211_H
14#define MAC80211_H
15
16#include <linux/bug.h>
17#include <linux/kernel.h>
18#include <linux/if_ether.h>
19#include <linux/skbuff.h>
20#include <linux/ieee80211.h>
21#include <net/cfg80211.h>
22#include <asm/unaligned.h>
23
24/**
25 * DOC: Introduction
26 *
27 * mac80211 is the Linux stack for 802.11 hardware that implements
28 * only partial functionality in hard- or firmware. This document
29 * defines the interface between mac80211 and low-level hardware
30 * drivers.
31 */
32
33/**
34 * DOC: Calling mac80211 from interrupts
35 *
36 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be
37 * called in hardware interrupt context. The low-level driver must not call any
38 * other functions in hardware interrupt context. If there is a need for such
39 * call, the low-level driver should first ACK the interrupt and perform the
40 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even
41 * tasklet function.
42 *
43 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also
44 * use the non-IRQ-safe functions!
45 */
46
47/**
48 * DOC: Warning
49 *
50 * If you're reading this document and not the header file itself, it will
51 * be incomplete because not all documentation has been converted yet.
52 */
53
54/**
55 * DOC: Frame format
56 *
57 * As a general rule, when frames are passed between mac80211 and the driver,
58 * they start with the IEEE 802.11 header and include the same octets that are
59 * sent over the air except for the FCS which should be calculated by the
60 * hardware.
61 *
62 * There are, however, various exceptions to this rule for advanced features:
63 *
64 * The first exception is for hardware encryption and decryption offload
65 * where the IV/ICV may or may not be generated in hardware.
66 *
67 * Secondly, when the hardware handles fragmentation, the frame handed to
68 * the driver from mac80211 is the MSDU, not the MPDU.
69 */
70
71/**
72 * DOC: mac80211 workqueue
73 *
74 * mac80211 provides its own workqueue for drivers and internal mac80211 use.
75 * The workqueue is a single threaded workqueue and can only be accessed by
76 * helpers for sanity checking. Drivers must ensure all work added onto the
77 * mac80211 workqueue should be cancelled on the driver stop() callback.
78 *
79 * mac80211 will flushed the workqueue upon interface removal and during
80 * suspend.
81 *
82 * All work performed on the mac80211 workqueue must not acquire the RTNL lock.
83 *
84 */
85
86struct device;
87
88/**
89 * enum ieee80211_max_queues - maximum number of queues
90 *
91 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues.
92 * @IEEE80211_MAX_QUEUE_MAP: bitmap with maximum queues set
93 */
94enum ieee80211_max_queues {
95 IEEE80211_MAX_QUEUES = 16,
96 IEEE80211_MAX_QUEUE_MAP = BIT(IEEE80211_MAX_QUEUES) - 1,
97};
98
99#define IEEE80211_INVAL_HW_QUEUE 0xff
100
101/**
102 * enum ieee80211_ac_numbers - AC numbers as used in mac80211
103 * @IEEE80211_AC_VO: voice
104 * @IEEE80211_AC_VI: video
105 * @IEEE80211_AC_BE: best effort
106 * @IEEE80211_AC_BK: background
107 */
108enum ieee80211_ac_numbers {
109 IEEE80211_AC_VO = 0,
110 IEEE80211_AC_VI = 1,
111 IEEE80211_AC_BE = 2,
112 IEEE80211_AC_BK = 3,
113};
114#define IEEE80211_NUM_ACS 4
115
116/**
117 * struct ieee80211_tx_queue_params - transmit queue configuration
118 *
119 * The information provided in this structure is required for QoS
120 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29.
121 *
122 * @aifs: arbitration interframe space [0..255]
123 * @cw_min: minimum contention window [a value of the form
124 * 2^n-1 in the range 1..32767]
125 * @cw_max: maximum contention window [like @cw_min]
126 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled
127 * @acm: is mandatory admission control required for the access category
128 * @uapsd: is U-APSD mode enabled for the queue
129 */
130struct ieee80211_tx_queue_params {
131 u16 txop;
132 u16 cw_min;
133 u16 cw_max;
134 u8 aifs;
135 bool acm;
136 bool uapsd;
137};
138
139struct ieee80211_low_level_stats {
140 unsigned int dot11ACKFailureCount;
141 unsigned int dot11RTSFailureCount;
142 unsigned int dot11FCSErrorCount;
143 unsigned int dot11RTSSuccessCount;
144};
145
146/**
147 * enum ieee80211_chanctx_change - change flag for channel context
148 * @IEEE80211_CHANCTX_CHANGE_WIDTH: The channel width changed
149 * @IEEE80211_CHANCTX_CHANGE_RX_CHAINS: The number of RX chains changed
150 * @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed
151 * @IEEE80211_CHANCTX_CHANGE_CHANNEL: switched to another operating channel,
152 * this is used only with channel switching with CSA
153 * @IEEE80211_CHANCTX_CHANGE_MIN_WIDTH: The min required channel width changed
154 */
155enum ieee80211_chanctx_change {
156 IEEE80211_CHANCTX_CHANGE_WIDTH = BIT(0),
157 IEEE80211_CHANCTX_CHANGE_RX_CHAINS = BIT(1),
158 IEEE80211_CHANCTX_CHANGE_RADAR = BIT(2),
159 IEEE80211_CHANCTX_CHANGE_CHANNEL = BIT(3),
160 IEEE80211_CHANCTX_CHANGE_MIN_WIDTH = BIT(4),
161};
162
163/**
164 * struct ieee80211_chanctx_conf - channel context that vifs may be tuned to
165 *
166 * This is the driver-visible part. The ieee80211_chanctx
167 * that contains it is visible in mac80211 only.
168 *
169 * @def: the channel definition
170 * @min_def: the minimum channel definition currently required.
171 * @rx_chains_static: The number of RX chains that must always be
172 * active on the channel to receive MIMO transmissions
173 * @rx_chains_dynamic: The number of RX chains that must be enabled
174 * after RTS/CTS handshake to receive SMPS MIMO transmissions;
175 * this will always be >= @rx_chains_static.
176 * @radar_enabled: whether radar detection is enabled on this channel.
177 * @drv_priv: data area for driver use, will always be aligned to
178 * sizeof(void *), size is determined in hw information.
179 */
180struct ieee80211_chanctx_conf {
181 struct cfg80211_chan_def def;
182 struct cfg80211_chan_def min_def;
183
184 u8 rx_chains_static, rx_chains_dynamic;
185
186 bool radar_enabled;
187
188 u8 drv_priv[0] __aligned(sizeof(void *));
189};
190
191/**
192 * enum ieee80211_bss_change - BSS change notification flags
193 *
194 * These flags are used with the bss_info_changed() callback
195 * to indicate which BSS parameter changed.
196 *
197 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated),
198 * also implies a change in the AID.
199 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed
200 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed
201 * @BSS_CHANGED_ERP_SLOT: slot timing changed
202 * @BSS_CHANGED_HT: 802.11n parameters changed
203 * @BSS_CHANGED_BASIC_RATES: Basic rateset changed
204 * @BSS_CHANGED_BEACON_INT: Beacon interval changed
205 * @BSS_CHANGED_BSSID: BSSID changed, for whatever
206 * reason (IBSS and managed mode)
207 * @BSS_CHANGED_BEACON: Beacon data changed, retrieve
208 * new beacon (beaconing modes)
209 * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be
210 * enabled/disabled (beaconing modes)
211 * @BSS_CHANGED_CQM: Connection quality monitor config changed
212 * @BSS_CHANGED_IBSS: IBSS join status changed
213 * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed.
214 * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note
215 * that it is only ever disabled for station mode.
216 * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface.
217 * @BSS_CHANGED_SSID: SSID changed for this BSS (AP and IBSS mode)
218 * @BSS_CHANGED_AP_PROBE_RESP: Probe Response changed for this BSS (AP mode)
219 * @BSS_CHANGED_PS: PS changed for this BSS (STA mode)
220 * @BSS_CHANGED_TXPOWER: TX power setting changed for this interface
221 * @BSS_CHANGED_P2P_PS: P2P powersave settings (CTWindow, opportunistic PS)
222 * changed (currently only in P2P client mode, GO mode will be later)
223 * @BSS_CHANGED_BEACON_INFO: Data from the AP's beacon became available:
224 * currently dtim_period only is under consideration.
225 * @BSS_CHANGED_BANDWIDTH: The bandwidth used by this interface changed,
226 * note that this is only called when it changes after the channel
227 * context had been assigned.
228 */
229enum ieee80211_bss_change {
230 BSS_CHANGED_ASSOC = 1<<0,
231 BSS_CHANGED_ERP_CTS_PROT = 1<<1,
232 BSS_CHANGED_ERP_PREAMBLE = 1<<2,
233 BSS_CHANGED_ERP_SLOT = 1<<3,
234 BSS_CHANGED_HT = 1<<4,
235 BSS_CHANGED_BASIC_RATES = 1<<5,
236 BSS_CHANGED_BEACON_INT = 1<<6,
237 BSS_CHANGED_BSSID = 1<<7,
238 BSS_CHANGED_BEACON = 1<<8,
239 BSS_CHANGED_BEACON_ENABLED = 1<<9,
240 BSS_CHANGED_CQM = 1<<10,
241 BSS_CHANGED_IBSS = 1<<11,
242 BSS_CHANGED_ARP_FILTER = 1<<12,
243 BSS_CHANGED_QOS = 1<<13,
244 BSS_CHANGED_IDLE = 1<<14,
245 BSS_CHANGED_SSID = 1<<15,
246 BSS_CHANGED_AP_PROBE_RESP = 1<<16,
247 BSS_CHANGED_PS = 1<<17,
248 BSS_CHANGED_TXPOWER = 1<<18,
249 BSS_CHANGED_P2P_PS = 1<<19,
250 BSS_CHANGED_BEACON_INFO = 1<<20,
251 BSS_CHANGED_BANDWIDTH = 1<<21,
252
253 /* when adding here, make sure to change ieee80211_reconfig */
254};
255
256/*
257 * The maximum number of IPv4 addresses listed for ARP filtering. If the number
258 * of addresses for an interface increase beyond this value, hardware ARP
259 * filtering will be disabled.
260 */
261#define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4
262
263/**
264 * enum ieee80211_rssi_event - RSSI threshold event
265 * An indicator for when RSSI goes below/above a certain threshold.
266 * @RSSI_EVENT_HIGH: AP's rssi crossed the high threshold set by the driver.
267 * @RSSI_EVENT_LOW: AP's rssi crossed the low threshold set by the driver.
268 */
269enum ieee80211_rssi_event {
270 RSSI_EVENT_HIGH,
271 RSSI_EVENT_LOW,
272};
273
274/**
275 * struct ieee80211_bss_conf - holds the BSS's changing parameters
276 *
277 * This structure keeps information about a BSS (and an association
278 * to that BSS) that can change during the lifetime of the BSS.
279 *
280 * @assoc: association status
281 * @ibss_joined: indicates whether this station is part of an IBSS
282 * or not
283 * @ibss_creator: indicates if a new IBSS network is being created
284 * @aid: association ID number, valid only when @assoc is true
285 * @use_cts_prot: use CTS protection
286 * @use_short_preamble: use 802.11b short preamble;
287 * if the hardware cannot handle this it must set the
288 * IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag
289 * @use_short_slot: use short slot time (only relevant for ERP);
290 * if the hardware cannot handle this it must set the
291 * IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag
292 * @dtim_period: num of beacons before the next DTIM, for beaconing,
293 * valid in station mode only if after the driver was notified
294 * with the %BSS_CHANGED_BEACON_INFO flag, will be non-zero then.
295 * @sync_tsf: last beacon's/probe response's TSF timestamp (could be old
296 * as it may have been received during scanning long ago). If the
297 * HW flag %IEEE80211_HW_TIMING_BEACON_ONLY is set, then this can
298 * only come from a beacon, but might not become valid until after
299 * association when a beacon is received (which is notified with the
300 * %BSS_CHANGED_DTIM flag.)
301 * @sync_device_ts: the device timestamp corresponding to the sync_tsf,
302 * the driver/device can use this to calculate synchronisation
303 * (see @sync_tsf)
304 * @sync_dtim_count: Only valid when %IEEE80211_HW_TIMING_BEACON_ONLY
305 * is requested, see @sync_tsf/@sync_device_ts.
306 * @beacon_int: beacon interval
307 * @assoc_capability: capabilities taken from assoc resp
308 * @basic_rates: bitmap of basic rates, each bit stands for an
309 * index into the rate table configured by the driver in
310 * the current band.
311 * @beacon_rate: associated AP's beacon TX rate
312 * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
313 * @bssid: The BSSID for this BSS
314 * @enable_beacon: whether beaconing should be enabled or not
315 * @chandef: Channel definition for this BSS -- the hardware might be
316 * configured a higher bandwidth than this BSS uses, for example.
317 * @ht_operation_mode: HT operation mode like in &struct ieee80211_ht_operation.
318 * This field is only valid when the channel type is one of the HT types.
319 * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
320 * implies disabled
321 * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis
322 * @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The
323 * may filter ARP queries targeted for other addresses than listed here.
324 * The driver must allow ARP queries targeted for all address listed here
325 * to pass through. An empty list implies no ARP queries need to pass.
326 * @arp_addr_cnt: Number of addresses currently on the list. Note that this
327 * may be larger than %IEEE80211_BSS_ARP_ADDR_LIST_LEN (the arp_addr_list
328 * array size), it's up to the driver what to do in that case.
329 * @qos: This is a QoS-enabled BSS.
330 * @idle: This interface is idle. There's also a global idle flag in the
331 * hardware config which may be more appropriate depending on what
332 * your driver/device needs to do.
333 * @ps: power-save mode (STA only). This flag is NOT affected by
334 * offchannel/dynamic_ps operations.
335 * @ssid: The SSID of the current vif. Valid in AP and IBSS mode.
336 * @ssid_len: Length of SSID given in @ssid.
337 * @hidden_ssid: The SSID of the current vif is hidden. Only valid in AP-mode.
338 * @txpower: TX power in dBm
339 * @p2p_noa_attr: P2P NoA attribute for P2P powersave
340 */
341struct ieee80211_bss_conf {
342 const u8 *bssid;
343 /* association related data */
344 bool assoc, ibss_joined;
345 bool ibss_creator;
346 u16 aid;
347 /* erp related data */
348 bool use_cts_prot;
349 bool use_short_preamble;
350 bool use_short_slot;
351 bool enable_beacon;
352 u8 dtim_period;
353 u16 beacon_int;
354 u16 assoc_capability;
355 u64 sync_tsf;
356 u32 sync_device_ts;
357 u8 sync_dtim_count;
358 u32 basic_rates;
359 struct ieee80211_rate *beacon_rate;
360 int mcast_rate[IEEE80211_NUM_BANDS];
361 u16 ht_operation_mode;
362 s32 cqm_rssi_thold;
363 u32 cqm_rssi_hyst;
364 struct cfg80211_chan_def chandef;
365 __be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN];
366 int arp_addr_cnt;
367 bool qos;
368 bool idle;
369 bool ps;
370 u8 ssid[IEEE80211_MAX_SSID_LEN];
371 size_t ssid_len;
372 bool hidden_ssid;
373 int txpower;
374 struct ieee80211_p2p_noa_attr p2p_noa_attr;
375};
376
377/**
378 * enum mac80211_tx_info_flags - flags to describe transmission information/status
379 *
380 * These flags are used with the @flags member of &ieee80211_tx_info.
381 *
382 * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame.
383 * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence
384 * number to this frame, taking care of not overwriting the fragment
385 * number and increasing the sequence number only when the
386 * IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly
387 * assign sequence numbers to QoS-data frames but cannot do so correctly
388 * for non-QoS-data and management frames because beacons need them from
389 * that counter as well and mac80211 cannot guarantee proper sequencing.
390 * If this flag is set, the driver should instruct the hardware to
391 * assign a sequence number to the frame or assign one itself. Cf. IEEE
392 * 802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for
393 * beacons and always be clear for frames without a sequence number field.
394 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
395 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
396 * station
397 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
398 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon
399 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU
400 * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211.
401 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
402 * because the destination STA was in powersave mode. Note that to
403 * avoid race conditions, the filter must be set by the hardware or
404 * firmware upon receiving a frame that indicates that the station
405 * went to sleep (must be done on device to filter frames already on
406 * the queue) and may only be unset after mac80211 gives the OK for
407 * that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above),
408 * since only then is it guaranteed that no more frames are in the
409 * hardware queue.
410 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged
411 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status
412 * is for the whole aggregation.
413 * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned,
414 * so consider using block ack request (BAR).
415 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be
416 * set by rate control algorithms to indicate probe rate, will
417 * be cleared for fragmented frames (except on the last fragment)
418 * @IEEE80211_TX_INTFL_OFFCHAN_TX_OK: Internal to mac80211. Used to indicate
419 * that a frame can be transmitted while the queues are stopped for
420 * off-channel operation.
421 * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211,
422 * used to indicate that a pending frame requires TX processing before
423 * it can be sent out.
424 * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211,
425 * used to indicate that a frame was already retried due to PS
426 * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211,
427 * used to indicate frame should not be encrypted
428 * @IEEE80211_TX_CTL_NO_PS_BUFFER: This frame is a response to a poll
429 * frame (PS-Poll or uAPSD) or a non-bufferable MMPDU and must
430 * be sent although the station is in powersave mode.
431 * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the
432 * transmit function after the current frame, this can be used
433 * by drivers to kick the DMA queue only if unset or when the
434 * queue gets full.
435 * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted
436 * after TX status because the destination was asleep, it must not
437 * be modified again (no seqno assignment, crypto, etc.)
438 * @IEEE80211_TX_INTFL_MLME_CONN_TX: This frame was transmitted by the MLME
439 * code for connection establishment, this indicates that its status
440 * should kick the MLME state machine.
441 * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211
442 * MLME command (internal to mac80211 to figure out whether to send TX
443 * status to user space)
444 * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame
445 * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this
446 * frame and selects the maximum number of streams that it can use.
447 * @IEEE80211_TX_CTL_TX_OFFCHAN: Marks this packet to be transmitted on
448 * the off-channel channel when a remain-on-channel offload is done
449 * in hardware -- normal packets still flow and are expected to be
450 * handled properly by the device.
451 * @IEEE80211_TX_INTFL_TKIP_MIC_FAILURE: Marks this packet to be used for TKIP
452 * testing. It will be sent out with incorrect Michael MIC key to allow
453 * TKIP countermeasures to be tested.
454 * @IEEE80211_TX_CTL_NO_CCK_RATE: This frame will be sent at non CCK rate.
455 * This flag is actually used for management frame especially for P2P
456 * frames not being sent at CCK rate in 2GHz band.
457 * @IEEE80211_TX_STATUS_EOSP: This packet marks the end of service period,
458 * when its status is reported the service period ends. For frames in
459 * an SP that mac80211 transmits, it is already set; for driver frames
460 * the driver may set this flag. It is also used to do the same for
461 * PS-Poll responses.
462 * @IEEE80211_TX_CTL_USE_MINRATE: This frame will be sent at lowest rate.
463 * This flag is used to send nullfunc frame at minimum rate when
464 * the nullfunc is used for connection monitoring purpose.
465 * @IEEE80211_TX_CTL_DONTFRAG: Don't fragment this packet even if it
466 * would be fragmented by size (this is optional, only used for
467 * monitor injection).
468 * @IEEE80211_TX_CTL_PS_RESPONSE: This frame is a response to a poll
469 * frame (PS-Poll or uAPSD).
470 *
471 * Note: If you have to add new flags to the enumeration, then don't
472 * forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary.
473 */
474enum mac80211_tx_info_flags {
475 IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
476 IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(1),
477 IEEE80211_TX_CTL_NO_ACK = BIT(2),
478 IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(3),
479 IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(4),
480 IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(5),
481 IEEE80211_TX_CTL_AMPDU = BIT(6),
482 IEEE80211_TX_CTL_INJECTED = BIT(7),
483 IEEE80211_TX_STAT_TX_FILTERED = BIT(8),
484 IEEE80211_TX_STAT_ACK = BIT(9),
485 IEEE80211_TX_STAT_AMPDU = BIT(10),
486 IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11),
487 IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12),
488 IEEE80211_TX_INTFL_OFFCHAN_TX_OK = BIT(13),
489 IEEE80211_TX_INTFL_NEED_TXPROCESSING = BIT(14),
490 IEEE80211_TX_INTFL_RETRIED = BIT(15),
491 IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16),
492 IEEE80211_TX_CTL_NO_PS_BUFFER = BIT(17),
493 IEEE80211_TX_CTL_MORE_FRAMES = BIT(18),
494 IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19),
495 IEEE80211_TX_INTFL_MLME_CONN_TX = BIT(20),
496 IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21),
497 IEEE80211_TX_CTL_LDPC = BIT(22),
498 IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24),
499 IEEE80211_TX_CTL_TX_OFFCHAN = BIT(25),
500 IEEE80211_TX_INTFL_TKIP_MIC_FAILURE = BIT(26),
501 IEEE80211_TX_CTL_NO_CCK_RATE = BIT(27),
502 IEEE80211_TX_STATUS_EOSP = BIT(28),
503 IEEE80211_TX_CTL_USE_MINRATE = BIT(29),
504 IEEE80211_TX_CTL_DONTFRAG = BIT(30),
505 IEEE80211_TX_CTL_PS_RESPONSE = BIT(31),
506};
507
508#define IEEE80211_TX_CTL_STBC_SHIFT 23
509
510/**
511 * enum mac80211_tx_control_flags - flags to describe transmit control
512 *
513 * @IEEE80211_TX_CTRL_PORT_CTRL_PROTO: this frame is a port control
514 * protocol frame (e.g. EAP)
515 *
516 * These flags are used in tx_info->control.flags.
517 */
518enum mac80211_tx_control_flags {
519 IEEE80211_TX_CTRL_PORT_CTRL_PROTO = BIT(0),
520};
521
522/*
523 * This definition is used as a mask to clear all temporary flags, which are
524 * set by the tx handlers for each transmission attempt by the mac80211 stack.
525 */
526#define IEEE80211_TX_TEMPORARY_FLAGS (IEEE80211_TX_CTL_NO_ACK | \
527 IEEE80211_TX_CTL_CLEAR_PS_FILT | IEEE80211_TX_CTL_FIRST_FRAGMENT | \
528 IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU | \
529 IEEE80211_TX_STAT_TX_FILTERED | IEEE80211_TX_STAT_ACK | \
530 IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK | \
531 IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_NO_PS_BUFFER | \
532 IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC | \
533 IEEE80211_TX_CTL_STBC | IEEE80211_TX_STATUS_EOSP)
534
535/**
536 * enum mac80211_rate_control_flags - per-rate flags set by the
537 * Rate Control algorithm.
538 *
539 * These flags are set by the Rate control algorithm for each rate during tx,
540 * in the @flags member of struct ieee80211_tx_rate.
541 *
542 * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate.
543 * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required.
544 * This is set if the current BSS requires ERP protection.
545 * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble.
546 * @IEEE80211_TX_RC_MCS: HT rate.
547 * @IEEE80211_TX_RC_VHT_MCS: VHT MCS rate, in this case the idx field is split
548 * into a higher 4 bits (Nss) and lower 4 bits (MCS number)
549 * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in
550 * Greenfield mode.
551 * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz.
552 * @IEEE80211_TX_RC_80_MHZ_WIDTH: Indicates 80 MHz transmission
553 * @IEEE80211_TX_RC_160_MHZ_WIDTH: Indicates 160 MHz transmission
554 * (80+80 isn't supported yet)
555 * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the
556 * adjacent 20 MHz channels, if the current channel type is
557 * NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS.
558 * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate.
559 */
560enum mac80211_rate_control_flags {
561 IEEE80211_TX_RC_USE_RTS_CTS = BIT(0),
562 IEEE80211_TX_RC_USE_CTS_PROTECT = BIT(1),
563 IEEE80211_TX_RC_USE_SHORT_PREAMBLE = BIT(2),
564
565 /* rate index is an HT/VHT MCS instead of an index */
566 IEEE80211_TX_RC_MCS = BIT(3),
567 IEEE80211_TX_RC_GREEN_FIELD = BIT(4),
568 IEEE80211_TX_RC_40_MHZ_WIDTH = BIT(5),
569 IEEE80211_TX_RC_DUP_DATA = BIT(6),
570 IEEE80211_TX_RC_SHORT_GI = BIT(7),
571 IEEE80211_TX_RC_VHT_MCS = BIT(8),
572 IEEE80211_TX_RC_80_MHZ_WIDTH = BIT(9),
573 IEEE80211_TX_RC_160_MHZ_WIDTH = BIT(10),
574};
575
576
577/* there are 40 bytes if you don't need the rateset to be kept */
578#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40
579
580/* if you do need the rateset, then you have less space */
581#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24
582
583/* maximum number of rate stages */
584#define IEEE80211_TX_MAX_RATES 4
585
586/* maximum number of rate table entries */
587#define IEEE80211_TX_RATE_TABLE_SIZE 4
588
589/**
590 * struct ieee80211_tx_rate - rate selection/status
591 *
592 * @idx: rate index to attempt to send with
593 * @flags: rate control flags (&enum mac80211_rate_control_flags)
594 * @count: number of tries in this rate before going to the next rate
595 *
596 * A value of -1 for @idx indicates an invalid rate and, if used
597 * in an array of retry rates, that no more rates should be tried.
598 *
599 * When used for transmit status reporting, the driver should
600 * always report the rate along with the flags it used.
601 *
602 * &struct ieee80211_tx_info contains an array of these structs
603 * in the control information, and it will be filled by the rate
604 * control algorithm according to what should be sent. For example,
605 * if this array contains, in the format { <idx>, <count> } the
606 * information
607 * { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 }
608 * then this means that the frame should be transmitted
609 * up to twice at rate 3, up to twice at rate 2, and up to four
610 * times at rate 1 if it doesn't get acknowledged. Say it gets
611 * acknowledged by the peer after the fifth attempt, the status
612 * information should then contain
613 * { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ...
614 * since it was transmitted twice at rate 3, twice at rate 2
615 * and once at rate 1 after which we received an acknowledgement.
616 */
617struct ieee80211_tx_rate {
618 s8 idx;
619 u16 count:5,
620 flags:11;
621} __packed;
622
623#define IEEE80211_MAX_TX_RETRY 31
624
625static inline void ieee80211_rate_set_vht(struct ieee80211_tx_rate *rate,
626 u8 mcs, u8 nss)
627{
628 WARN_ON(mcs & ~0xF);
629 WARN_ON((nss - 1) & ~0x7);
630 rate->idx = ((nss - 1) << 4) | mcs;
631}
632
633static inline u8
634ieee80211_rate_get_vht_mcs(const struct ieee80211_tx_rate *rate)
635{
636 return rate->idx & 0xF;
637}
638
639static inline u8
640ieee80211_rate_get_vht_nss(const struct ieee80211_tx_rate *rate)
641{
642 return (rate->idx >> 4) + 1;
643}
644
645/**
646 * struct ieee80211_tx_info - skb transmit information
647 *
648 * This structure is placed in skb->cb for three uses:
649 * (1) mac80211 TX control - mac80211 tells the driver what to do
650 * (2) driver internal use (if applicable)
651 * (3) TX status information - driver tells mac80211 what happened
652 *
653 * @flags: transmit info flags, defined above
654 * @band: the band to transmit on (use for checking for races)
655 * @hw_queue: HW queue to put the frame on, skb_get_queue_mapping() gives the AC
656 * @ack_frame_id: internal frame ID for TX status, used internally
657 * @control: union for control data
658 * @status: union for status data
659 * @driver_data: array of driver_data pointers
660 * @ampdu_ack_len: number of acked aggregated frames.
661 * relevant only if IEEE80211_TX_STAT_AMPDU was set.
662 * @ampdu_len: number of aggregated frames.
663 * relevant only if IEEE80211_TX_STAT_AMPDU was set.
664 * @ack_signal: signal strength of the ACK frame
665 */
666struct ieee80211_tx_info {
667 /* common information */
668 u32 flags;
669 u8 band;
670
671 u8 hw_queue;
672
673 u16 ack_frame_id;
674
675 union {
676 struct {
677 union {
678 /* rate control */
679 struct {
680 struct ieee80211_tx_rate rates[
681 IEEE80211_TX_MAX_RATES];
682 s8 rts_cts_rate_idx;
683 u8 use_rts:1;
684 u8 use_cts_prot:1;
685 u8 short_preamble:1;
686 u8 skip_table:1;
687 /* 2 bytes free */
688 };
689 /* only needed before rate control */
690 unsigned long jiffies;
691 };
692 /* NB: vif can be NULL for injected frames */
693 struct ieee80211_vif *vif;
694 struct ieee80211_key_conf *hw_key;
695 u32 flags;
696 /* 4 bytes free */
697 } control;
698 struct {
699 struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
700 s32 ack_signal;
701 u8 ampdu_ack_len;
702 u8 ampdu_len;
703 u8 antenna;
704 void *status_driver_data[21 / sizeof(void *)];
705 } status;
706 struct {
707 struct ieee80211_tx_rate driver_rates[
708 IEEE80211_TX_MAX_RATES];
709 u8 pad[4];
710
711 void *rate_driver_data[
712 IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)];
713 };
714 void *driver_data[
715 IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)];
716 };
717};
718
719/**
720 * struct ieee80211_sched_scan_ies - scheduled scan IEs
721 *
722 * This structure is used to pass the appropriate IEs to be used in scheduled
723 * scans for all bands. It contains both the IEs passed from the userspace
724 * and the ones generated by mac80211.
725 *
726 * @ie: array with the IEs for each supported band
727 * @len: array with the total length of the IEs for each band
728 */
729struct ieee80211_sched_scan_ies {
730 u8 *ie[IEEE80211_NUM_BANDS];
731 size_t len[IEEE80211_NUM_BANDS];
732};
733
734static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
735{
736 return (struct ieee80211_tx_info *)skb->cb;
737}
738
739static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb)
740{
741 return (struct ieee80211_rx_status *)skb->cb;
742}
743
744/**
745 * ieee80211_tx_info_clear_status - clear TX status
746 *
747 * @info: The &struct ieee80211_tx_info to be cleared.
748 *
749 * When the driver passes an skb back to mac80211, it must report
750 * a number of things in TX status. This function clears everything
751 * in the TX status but the rate control information (it does clear
752 * the count since you need to fill that in anyway).
753 *
754 * NOTE: You can only use this function if you do NOT use
755 * info->driver_data! Use info->rate_driver_data
756 * instead if you need only the less space that allows.
757 */
758static inline void
759ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
760{
761 int i;
762
763 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
764 offsetof(struct ieee80211_tx_info, control.rates));
765 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) !=
766 offsetof(struct ieee80211_tx_info, driver_rates));
767 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8);
768 /* clear the rate counts */
769 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++)
770 info->status.rates[i].count = 0;
771
772 BUILD_BUG_ON(
773 offsetof(struct ieee80211_tx_info, status.ack_signal) != 20);
774 memset(&info->status.ampdu_ack_len, 0,
775 sizeof(struct ieee80211_tx_info) -
776 offsetof(struct ieee80211_tx_info, status.ampdu_ack_len));
777}
778
779
780/**
781 * enum mac80211_rx_flags - receive flags
782 *
783 * These flags are used with the @flag member of &struct ieee80211_rx_status.
784 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
785 * Use together with %RX_FLAG_MMIC_STRIPPED.
786 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
787 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
788 * verification has been done by the hardware.
789 * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
790 * If this flag is set, the stack cannot do any replay detection
791 * hence the driver or hardware will have to do that.
792 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on
793 * the frame.
794 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on
795 * the frame.
796 * @RX_FLAG_MACTIME_START: The timestamp passed in the RX status (@mactime
797 * field) is valid and contains the time the first symbol of the MPDU
798 * was received. This is useful in monitor mode and for proper IBSS
799 * merging.
800 * @RX_FLAG_MACTIME_END: The timestamp passed in the RX status (@mactime
801 * field) is valid and contains the time the last symbol of the MPDU
802 * (including FCS) was received.
803 * @RX_FLAG_SHORTPRE: Short preamble was used for this frame
804 * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index
805 * @RX_FLAG_VHT: VHT MCS was used and rate_index is MCS index
806 * @RX_FLAG_40MHZ: HT40 (40 MHz) was used
807 * @RX_FLAG_SHORT_GI: Short guard interval was used
808 * @RX_FLAG_NO_SIGNAL_VAL: The signal strength value is not present.
809 * Valid only for data frames (mainly A-MPDU)
810 * @RX_FLAG_HT_GF: This frame was received in a HT-greenfield transmission, if
811 * the driver fills this value it should add %IEEE80211_RADIOTAP_MCS_HAVE_FMT
812 * to hw.radiotap_mcs_details to advertise that fact
813 * @RX_FLAG_AMPDU_DETAILS: A-MPDU details are known, in particular the reference
814 * number (@ampdu_reference) must be populated and be a distinct number for
815 * each A-MPDU
816 * @RX_FLAG_AMPDU_REPORT_ZEROLEN: driver reports 0-length subframes
817 * @RX_FLAG_AMPDU_IS_ZEROLEN: This is a zero-length subframe, for
818 * monitoring purposes only
819 * @RX_FLAG_AMPDU_LAST_KNOWN: last subframe is known, should be set on all
820 * subframes of a single A-MPDU
821 * @RX_FLAG_AMPDU_IS_LAST: this subframe is the last subframe of the A-MPDU
822 * @RX_FLAG_AMPDU_DELIM_CRC_ERROR: A delimiter CRC error has been detected
823 * on this subframe
824 * @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC
825 * is stored in the @ampdu_delimiter_crc field)
826 * @RX_FLAG_LDPC: LDPC was used
827 * @RX_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
828 * @RX_FLAG_10MHZ: 10 MHz (half channel) was used
829 * @RX_FLAG_5MHZ: 5 MHz (quarter channel) was used
830 * @RX_FLAG_AMSDU_MORE: Some drivers may prefer to report separate A-MSDU
831 * subframes instead of a one huge frame for performance reasons.
832 * All, but the last MSDU from an A-MSDU should have this flag set. E.g.
833 * if an A-MSDU has 3 frames, the first 2 must have the flag set, while
834 * the 3rd (last) one must not have this flag set. The flag is used to
835 * deal with retransmission/duplication recovery properly since A-MSDU
836 * subframes share the same sequence number. Reported subframes can be
837 * either regular MSDU or singly A-MSDUs. Subframes must not be
838 * interleaved with other frames.
839 */
840enum mac80211_rx_flags {
841 RX_FLAG_MMIC_ERROR = BIT(0),
842 RX_FLAG_DECRYPTED = BIT(1),
843 RX_FLAG_MMIC_STRIPPED = BIT(3),
844 RX_FLAG_IV_STRIPPED = BIT(4),
845 RX_FLAG_FAILED_FCS_CRC = BIT(5),
846 RX_FLAG_FAILED_PLCP_CRC = BIT(6),
847 RX_FLAG_MACTIME_START = BIT(7),
848 RX_FLAG_SHORTPRE = BIT(8),
849 RX_FLAG_HT = BIT(9),
850 RX_FLAG_40MHZ = BIT(10),
851 RX_FLAG_SHORT_GI = BIT(11),
852 RX_FLAG_NO_SIGNAL_VAL = BIT(12),
853 RX_FLAG_HT_GF = BIT(13),
854 RX_FLAG_AMPDU_DETAILS = BIT(14),
855 RX_FLAG_AMPDU_REPORT_ZEROLEN = BIT(15),
856 RX_FLAG_AMPDU_IS_ZEROLEN = BIT(16),
857 RX_FLAG_AMPDU_LAST_KNOWN = BIT(17),
858 RX_FLAG_AMPDU_IS_LAST = BIT(18),
859 RX_FLAG_AMPDU_DELIM_CRC_ERROR = BIT(19),
860 RX_FLAG_AMPDU_DELIM_CRC_KNOWN = BIT(20),
861 RX_FLAG_MACTIME_END = BIT(21),
862 RX_FLAG_VHT = BIT(22),
863 RX_FLAG_LDPC = BIT(23),
864 RX_FLAG_STBC_MASK = BIT(26) | BIT(27),
865 RX_FLAG_10MHZ = BIT(28),
866 RX_FLAG_5MHZ = BIT(29),
867 RX_FLAG_AMSDU_MORE = BIT(30),
868};
869
870#define RX_FLAG_STBC_SHIFT 26
871
872/**
873 * enum mac80211_rx_vht_flags - receive VHT flags
874 *
875 * These flags are used with the @vht_flag member of
876 * &struct ieee80211_rx_status.
877 * @RX_VHT_FLAG_80MHZ: 80 MHz was used
878 * @RX_VHT_FLAG_80P80MHZ: 80+80 MHz was used
879 * @RX_VHT_FLAG_160MHZ: 160 MHz was used
880 * @RX_VHT_FLAG_BF: packet was beamformed
881 */
882enum mac80211_rx_vht_flags {
883 RX_VHT_FLAG_80MHZ = BIT(0),
884 RX_VHT_FLAG_80P80MHZ = BIT(1),
885 RX_VHT_FLAG_160MHZ = BIT(2),
886 RX_VHT_FLAG_BF = BIT(3),
887};
888
889/**
890 * struct ieee80211_rx_status - receive status
891 *
892 * The low-level driver should provide this information (the subset
893 * supported by hardware) to the 802.11 code with each received
894 * frame, in the skb's control buffer (cb).
895 *
896 * @mactime: value in microseconds of the 64-bit Time Synchronization Function
897 * (TSF) timer when the first data symbol (MPDU) arrived at the hardware.
898 * @device_timestamp: arbitrary timestamp for the device, mac80211 doesn't use
899 * it but can store it and pass it back to the driver for synchronisation
900 * @band: the active band when this frame was received
901 * @freq: frequency the radio was tuned to when receiving this frame, in MHz
902 * @signal: signal strength when receiving this frame, either in dBm, in dB or
903 * unspecified depending on the hardware capabilities flags
904 * @IEEE80211_HW_SIGNAL_*
905 * @chains: bitmask of receive chains for which separate signal strength
906 * values were filled.
907 * @chain_signal: per-chain signal strength, in dBm (unlike @signal, doesn't
908 * support dB or unspecified units)
909 * @antenna: antenna used
910 * @rate_idx: index of data rate into band's supported rates or MCS index if
911 * HT or VHT is used (%RX_FLAG_HT/%RX_FLAG_VHT)
912 * @vht_nss: number of streams (VHT only)
913 * @flag: %RX_FLAG_*
914 * @vht_flag: %RX_VHT_FLAG_*
915 * @rx_flags: internal RX flags for mac80211
916 * @ampdu_reference: A-MPDU reference number, must be a different value for
917 * each A-MPDU but the same for each subframe within one A-MPDU
918 * @ampdu_delimiter_crc: A-MPDU delimiter CRC
919 */
920struct ieee80211_rx_status {
921 u64 mactime;
922 u32 device_timestamp;
923 u32 ampdu_reference;
924 u32 flag;
925 u16 freq;
926 u8 vht_flag;
927 u8 rate_idx;
928 u8 vht_nss;
929 u8 rx_flags;
930 u8 band;
931 u8 antenna;
932 s8 signal;
933 u8 chains;
934 s8 chain_signal[IEEE80211_MAX_CHAINS];
935 u8 ampdu_delimiter_crc;
936};
937
938/**
939 * enum ieee80211_conf_flags - configuration flags
940 *
941 * Flags to define PHY configuration options
942 *
943 * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
944 * to determine for example whether to calculate timestamps for packets
945 * or not, do not use instead of filter flags!
946 * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only).
947 * This is the power save mode defined by IEEE 802.11-2007 section 11.2,
948 * meaning that the hardware still wakes up for beacons, is able to
949 * transmit frames and receive the possible acknowledgment frames.
950 * Not to be confused with hardware specific wakeup/sleep states,
951 * driver is responsible for that. See the section "Powersave support"
952 * for more.
953 * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
954 * the driver should be prepared to handle configuration requests but
955 * may turn the device off as much as possible. Typically, this flag will
956 * be set when an interface is set UP but not associated or scanning, but
957 * it can also be unset in that case when monitor interfaces are active.
958 * @IEEE80211_CONF_OFFCHANNEL: The device is currently not on its main
959 * operating channel.
960 */
961enum ieee80211_conf_flags {
962 IEEE80211_CONF_MONITOR = (1<<0),
963 IEEE80211_CONF_PS = (1<<1),
964 IEEE80211_CONF_IDLE = (1<<2),
965 IEEE80211_CONF_OFFCHANNEL = (1<<3),
966};
967
968
969/**
970 * enum ieee80211_conf_changed - denotes which configuration changed
971 *
972 * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
973 * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed
974 * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
975 * @IEEE80211_CONF_CHANGE_POWER: the TX power changed
976 * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
977 * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
978 * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
979 * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
980 * Note that this is only valid if channel contexts are not used,
981 * otherwise each channel context has the number of chains listed.
982 */
983enum ieee80211_conf_changed {
984 IEEE80211_CONF_CHANGE_SMPS = BIT(1),
985 IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2),
986 IEEE80211_CONF_CHANGE_MONITOR = BIT(3),
987 IEEE80211_CONF_CHANGE_PS = BIT(4),
988 IEEE80211_CONF_CHANGE_POWER = BIT(5),
989 IEEE80211_CONF_CHANGE_CHANNEL = BIT(6),
990 IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(7),
991 IEEE80211_CONF_CHANGE_IDLE = BIT(8),
992};
993
994/**
995 * enum ieee80211_smps_mode - spatial multiplexing power save mode
996 *
997 * @IEEE80211_SMPS_AUTOMATIC: automatic
998 * @IEEE80211_SMPS_OFF: off
999 * @IEEE80211_SMPS_STATIC: static
1000 * @IEEE80211_SMPS_DYNAMIC: dynamic
1001 * @IEEE80211_SMPS_NUM_MODES: internal, don't use
1002 */
1003enum ieee80211_smps_mode {
1004 IEEE80211_SMPS_AUTOMATIC,
1005 IEEE80211_SMPS_OFF,
1006 IEEE80211_SMPS_STATIC,
1007 IEEE80211_SMPS_DYNAMIC,
1008
1009 /* keep last */
1010 IEEE80211_SMPS_NUM_MODES,
1011};
1012
1013/**
1014 * struct ieee80211_conf - configuration of the device
1015 *
1016 * This struct indicates how the driver shall configure the hardware.
1017 *
1018 * @flags: configuration flags defined above
1019 *
1020 * @listen_interval: listen interval in units of beacon interval
1021 * @max_sleep_period: the maximum number of beacon intervals to sleep for
1022 * before checking the beacon for a TIM bit (managed mode only); this
1023 * value will be only achievable between DTIM frames, the hardware
1024 * needs to check for the multicast traffic bit in DTIM beacons.
1025 * This variable is valid only when the CONF_PS flag is set.
1026 * @ps_dtim_period: The DTIM period of the AP we're connected to, for use
1027 * in power saving. Power saving will not be enabled until a beacon
1028 * has been received and the DTIM period is known.
1029 * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the
1030 * powersave documentation below. This variable is valid only when
1031 * the CONF_PS flag is set.
1032 *
1033 * @power_level: requested transmit power (in dBm), backward compatibility
1034 * value only that is set to the minimum of all interfaces
1035 *
1036 * @chandef: the channel definition to tune to
1037 * @radar_enabled: whether radar detection is enabled
1038 *
1039 * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
1040 * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
1041 * but actually means the number of transmissions not the number of retries
1042 * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
1043 * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
1044 * number of transmissions not the number of retries
1045 *
1046 * @smps_mode: spatial multiplexing powersave mode; note that
1047 * %IEEE80211_SMPS_STATIC is used when the device is not
1048 * configured for an HT channel.
1049 * Note that this is only valid if channel contexts are not used,
1050 * otherwise each channel context has the number of chains listed.
1051 */
1052struct ieee80211_conf {
1053 u32 flags;
1054 int power_level, dynamic_ps_timeout;
1055 int max_sleep_period;
1056
1057 u16 listen_interval;
1058 u8 ps_dtim_period;
1059
1060 u8 long_frame_max_tx_count, short_frame_max_tx_count;
1061
1062 struct cfg80211_chan_def chandef;
1063 bool radar_enabled;
1064 enum ieee80211_smps_mode smps_mode;
1065};
1066
1067/**
1068 * struct ieee80211_channel_switch - holds the channel switch data
1069 *
1070 * The information provided in this structure is required for channel switch
1071 * operation.
1072 *
1073 * @timestamp: value in microseconds of the 64-bit Time Synchronization
1074 * Function (TSF) timer when the frame containing the channel switch
1075 * announcement was received. This is simply the rx.mactime parameter
1076 * the driver passed into mac80211.
1077 * @block_tx: Indicates whether transmission must be blocked before the
1078 * scheduled channel switch, as indicated by the AP.
1079 * @chandef: the new channel to switch to
1080 * @count: the number of TBTT's until the channel switch event
1081 */
1082struct ieee80211_channel_switch {
1083 u64 timestamp;
1084 bool block_tx;
1085 struct cfg80211_chan_def chandef;
1086 u8 count;
1087};
1088
1089/**
1090 * enum ieee80211_vif_flags - virtual interface flags
1091 *
1092 * @IEEE80211_VIF_BEACON_FILTER: the device performs beacon filtering
1093 * on this virtual interface to avoid unnecessary CPU wakeups
1094 * @IEEE80211_VIF_SUPPORTS_CQM_RSSI: the device can do connection quality
1095 * monitoring on this virtual interface -- i.e. it can monitor
1096 * connection quality related parameters, such as the RSSI level and
1097 * provide notifications if configured trigger levels are reached.
1098 */
1099enum ieee80211_vif_flags {
1100 IEEE80211_VIF_BEACON_FILTER = BIT(0),
1101 IEEE80211_VIF_SUPPORTS_CQM_RSSI = BIT(1),
1102};
1103
1104/**
1105 * struct ieee80211_vif - per-interface data
1106 *
1107 * Data in this structure is continually present for driver
1108 * use during the life of a virtual interface.
1109 *
1110 * @type: type of this virtual interface
1111 * @bss_conf: BSS configuration for this interface, either our own
1112 * or the BSS we're associated to
1113 * @addr: address of this interface
1114 * @p2p: indicates whether this AP or STA interface is a p2p
1115 * interface, i.e. a GO or p2p-sta respectively
1116 * @csa_active: marks whether a channel switch is going on
1117 * @driver_flags: flags/capabilities the driver has for this interface,
1118 * these need to be set (or cleared) when the interface is added
1119 * or, if supported by the driver, the interface type is changed
1120 * at runtime, mac80211 will never touch this field
1121 * @hw_queue: hardware queue for each AC
1122 * @cab_queue: content-after-beacon (DTIM beacon really) queue, AP mode only
1123 * @chanctx_conf: The channel context this interface is assigned to, or %NULL
1124 * when it is not assigned. This pointer is RCU-protected due to the TX
1125 * path needing to access it; even though the netdev carrier will always
1126 * be off when it is %NULL there can still be races and packets could be
1127 * processed after it switches back to %NULL.
1128 * @debugfs_dir: debugfs dentry, can be used by drivers to create own per
1129 * interface debug files. Note that it will be NULL for the virtual
1130 * monitor interface (if that is requested.)
1131 * @drv_priv: data area for driver use, will always be aligned to
1132 * sizeof(void *).
1133 */
1134struct ieee80211_vif {
1135 enum nl80211_iftype type;
1136 struct ieee80211_bss_conf bss_conf;
1137 u8 addr[ETH_ALEN];
1138 bool p2p;
1139 bool csa_active;
1140
1141 u8 cab_queue;
1142 u8 hw_queue[IEEE80211_NUM_ACS];
1143
1144 struct ieee80211_chanctx_conf __rcu *chanctx_conf;
1145
1146 u32 driver_flags;
1147
1148#ifdef CONFIG_MAC80211_DEBUGFS
1149 struct dentry *debugfs_dir;
1150#endif
1151
1152 /* must be last */
1153 u8 drv_priv[0] __aligned(sizeof(void *));
1154};
1155
1156static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif)
1157{
1158#ifdef CONFIG_MAC80211_MESH
1159 return vif->type == NL80211_IFTYPE_MESH_POINT;
1160#endif
1161 return false;
1162}
1163
1164/**
1165 * wdev_to_ieee80211_vif - return a vif struct from a wdev
1166 * @wdev: the wdev to get the vif for
1167 *
1168 * This can be used by mac80211 drivers with direct cfg80211 APIs
1169 * (like the vendor commands) that get a wdev.
1170 *
1171 * Note that this function may return %NULL if the given wdev isn't
1172 * associated with a vif that the driver knows about (e.g. monitor
1173 * or AP_VLAN interfaces.)
1174 */
1175struct ieee80211_vif *wdev_to_ieee80211_vif(struct wireless_dev *wdev);
1176
1177/**
1178 * enum ieee80211_key_flags - key flags
1179 *
1180 * These flags are used for communication about keys between the driver
1181 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf.
1182 *
1183 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the
1184 * driver to indicate that it requires IV generation for this
1185 * particular key.
1186 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by
1187 * the driver for a TKIP key if it requires Michael MIC
1188 * generation in software.
1189 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates
1190 * that the key is pairwise rather then a shared key.
1191 * @IEEE80211_KEY_FLAG_SW_MGMT_TX: This flag should be set by the driver for a
1192 * CCMP key if it requires CCMP encryption of management frames (MFP) to
1193 * be done in software.
1194 * @IEEE80211_KEY_FLAG_PUT_IV_SPACE: This flag should be set by the driver
1195 * if space should be prepared for the IV, but the IV
1196 * itself should not be generated. Do not set together with
1197 * @IEEE80211_KEY_FLAG_GENERATE_IV on the same key.
1198 * @IEEE80211_KEY_FLAG_RX_MGMT: This key will be used to decrypt received
1199 * management frames. The flag can help drivers that have a hardware
1200 * crypto implementation that doesn't deal with management frames
1201 * properly by allowing them to not upload the keys to hardware and
1202 * fall back to software crypto. Note that this flag deals only with
1203 * RX, if your crypto engine can't deal with TX you can also set the
1204 * %IEEE80211_KEY_FLAG_SW_MGMT_TX flag to encrypt such frames in SW.
1205 */
1206enum ieee80211_key_flags {
1207 IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1,
1208 IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2,
1209 IEEE80211_KEY_FLAG_PAIRWISE = 1<<3,
1210 IEEE80211_KEY_FLAG_SW_MGMT_TX = 1<<4,
1211 IEEE80211_KEY_FLAG_PUT_IV_SPACE = 1<<5,
1212 IEEE80211_KEY_FLAG_RX_MGMT = 1<<6,
1213};
1214
1215/**
1216 * struct ieee80211_key_conf - key information
1217 *
1218 * This key information is given by mac80211 to the driver by
1219 * the set_key() callback in &struct ieee80211_ops.
1220 *
1221 * @hw_key_idx: To be set by the driver, this is the key index the driver
1222 * wants to be given when a frame is transmitted and needs to be
1223 * encrypted in hardware.
1224 * @cipher: The key's cipher suite selector.
1225 * @flags: key flags, see &enum ieee80211_key_flags.
1226 * @keyidx: the key index (0-3)
1227 * @keylen: key material length
1228 * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte)
1229 * data block:
1230 * - Temporal Encryption Key (128 bits)
1231 * - Temporal Authenticator Tx MIC Key (64 bits)
1232 * - Temporal Authenticator Rx MIC Key (64 bits)
1233 * @icv_len: The ICV length for this key type
1234 * @iv_len: The IV length for this key type
1235 */
1236struct ieee80211_key_conf {
1237 u32 cipher;
1238 u8 icv_len;
1239 u8 iv_len;
1240 u8 hw_key_idx;
1241 u8 flags;
1242 s8 keyidx;
1243 u8 keylen;
1244 u8 key[0];
1245};
1246
1247/**
1248 * struct ieee80211_cipher_scheme - cipher scheme
1249 *
1250 * This structure contains a cipher scheme information defining
1251 * the secure packet crypto handling.
1252 *
1253 * @cipher: a cipher suite selector
1254 * @iftype: a cipher iftype bit mask indicating an allowed cipher usage
1255 * @hdr_len: a length of a security header used the cipher
1256 * @pn_len: a length of a packet number in the security header
1257 * @pn_off: an offset of pn from the beginning of the security header
1258 * @key_idx_off: an offset of key index byte in the security header
1259 * @key_idx_mask: a bit mask of key_idx bits
1260 * @key_idx_shift: a bit shift needed to get key_idx
1261 * key_idx value calculation:
1262 * (sec_header_base[key_idx_off] & key_idx_mask) >> key_idx_shift
1263 * @mic_len: a mic length in bytes
1264 */
1265struct ieee80211_cipher_scheme {
1266 u32 cipher;
1267 u16 iftype;
1268 u8 hdr_len;
1269 u8 pn_len;
1270 u8 pn_off;
1271 u8 key_idx_off;
1272 u8 key_idx_mask;
1273 u8 key_idx_shift;
1274 u8 mic_len;
1275};
1276
1277/**
1278 * enum set_key_cmd - key command
1279 *
1280 * Used with the set_key() callback in &struct ieee80211_ops, this
1281 * indicates whether a key is being removed or added.
1282 *
1283 * @SET_KEY: a key is set
1284 * @DISABLE_KEY: a key must be disabled
1285 */
1286enum set_key_cmd {
1287 SET_KEY, DISABLE_KEY,
1288};
1289
1290/**
1291 * enum ieee80211_sta_state - station state
1292 *
1293 * @IEEE80211_STA_NOTEXIST: station doesn't exist at all,
1294 * this is a special state for add/remove transitions
1295 * @IEEE80211_STA_NONE: station exists without special state
1296 * @IEEE80211_STA_AUTH: station is authenticated
1297 * @IEEE80211_STA_ASSOC: station is associated
1298 * @IEEE80211_STA_AUTHORIZED: station is authorized (802.1X)
1299 */
1300enum ieee80211_sta_state {
1301 /* NOTE: These need to be ordered correctly! */
1302 IEEE80211_STA_NOTEXIST,
1303 IEEE80211_STA_NONE,
1304 IEEE80211_STA_AUTH,
1305 IEEE80211_STA_ASSOC,
1306 IEEE80211_STA_AUTHORIZED,
1307};
1308
1309/**
1310 * enum ieee80211_sta_rx_bandwidth - station RX bandwidth
1311 * @IEEE80211_STA_RX_BW_20: station can only receive 20 MHz
1312 * @IEEE80211_STA_RX_BW_40: station can receive up to 40 MHz
1313 * @IEEE80211_STA_RX_BW_80: station can receive up to 80 MHz
1314 * @IEEE80211_STA_RX_BW_160: station can receive up to 160 MHz
1315 * (including 80+80 MHz)
1316 *
1317 * Implementation note: 20 must be zero to be initialized
1318 * correctly, the values must be sorted.
1319 */
1320enum ieee80211_sta_rx_bandwidth {
1321 IEEE80211_STA_RX_BW_20 = 0,
1322 IEEE80211_STA_RX_BW_40,
1323 IEEE80211_STA_RX_BW_80,
1324 IEEE80211_STA_RX_BW_160,
1325};
1326
1327/**
1328 * struct ieee80211_sta_rates - station rate selection table
1329 *
1330 * @rcu_head: RCU head used for freeing the table on update
1331 * @rate: transmit rates/flags to be used by default.
1332 * Overriding entries per-packet is possible by using cb tx control.
1333 */
1334struct ieee80211_sta_rates {
1335 struct rcu_head rcu_head;
1336 struct {
1337 s8 idx;
1338 u8 count;
1339 u8 count_cts;
1340 u8 count_rts;
1341 u16 flags;
1342 } rate[IEEE80211_TX_RATE_TABLE_SIZE];
1343};
1344
1345/**
1346 * struct ieee80211_sta - station table entry
1347 *
1348 * A station table entry represents a station we are possibly
1349 * communicating with. Since stations are RCU-managed in
1350 * mac80211, any ieee80211_sta pointer you get access to must
1351 * either be protected by rcu_read_lock() explicitly or implicitly,
1352 * or you must take good care to not use such a pointer after a
1353 * call to your sta_remove callback that removed it.
1354 *
1355 * @addr: MAC address
1356 * @aid: AID we assigned to the station if we're an AP
1357 * @supp_rates: Bitmap of supported rates (per band)
1358 * @ht_cap: HT capabilities of this STA; restricted to our own capabilities
1359 * @vht_cap: VHT capabilities of this STA; restricted to our own capabilities
1360 * @wme: indicates whether the STA supports WME. Only valid during AP-mode.
1361 * @drv_priv: data area for driver use, will always be aligned to
1362 * sizeof(void *), size is determined in hw information.
1363 * @uapsd_queues: bitmap of queues configured for uapsd. Only valid
1364 * if wme is supported.
1365 * @max_sp: max Service Period. Only valid if wme is supported.
1366 * @bandwidth: current bandwidth the station can receive with
1367 * @rx_nss: in HT/VHT, the maximum number of spatial streams the
1368 * station can receive at the moment, changed by operating mode
1369 * notifications and capabilities. The value is only valid after
1370 * the station moves to associated state.
1371 * @smps_mode: current SMPS mode (off, static or dynamic)
1372 * @rates: rate control selection table
1373 */
1374struct ieee80211_sta {
1375 u32 supp_rates[IEEE80211_NUM_BANDS];
1376 u8 addr[ETH_ALEN];
1377 u16 aid;
1378 struct ieee80211_sta_ht_cap ht_cap;
1379 struct ieee80211_sta_vht_cap vht_cap;
1380 bool wme;
1381 u8 uapsd_queues;
1382 u8 max_sp;
1383 u8 rx_nss;
1384 enum ieee80211_sta_rx_bandwidth bandwidth;
1385 enum ieee80211_smps_mode smps_mode;
1386 struct ieee80211_sta_rates __rcu *rates;
1387
1388 /* must be last */
1389 u8 drv_priv[0] __aligned(sizeof(void *));
1390};
1391
1392/**
1393 * enum sta_notify_cmd - sta notify command
1394 *
1395 * Used with the sta_notify() callback in &struct ieee80211_ops, this
1396 * indicates if an associated station made a power state transition.
1397 *
1398 * @STA_NOTIFY_SLEEP: a station is now sleeping
1399 * @STA_NOTIFY_AWAKE: a sleeping station woke up
1400 */
1401enum sta_notify_cmd {
1402 STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE,
1403};
1404
1405/**
1406 * struct ieee80211_tx_control - TX control data
1407 *
1408 * @sta: station table entry, this sta pointer may be NULL and
1409 * it is not allowed to copy the pointer, due to RCU.
1410 */
1411struct ieee80211_tx_control {
1412 struct ieee80211_sta *sta;
1413};
1414
1415/**
1416 * enum ieee80211_hw_flags - hardware flags
1417 *
1418 * These flags are used to indicate hardware capabilities to
1419 * the stack. Generally, flags here should have their meaning
1420 * done in a way that the simplest hardware doesn't need setting
1421 * any particular flags. There are some exceptions to this rule,
1422 * however, so you are advised to review these flags carefully.
1423 *
1424 * @IEEE80211_HW_HAS_RATE_CONTROL:
1425 * The hardware or firmware includes rate control, and cannot be
1426 * controlled by the stack. As such, no rate control algorithm
1427 * should be instantiated, and the TX rate reported to userspace
1428 * will be taken from the TX status instead of the rate control
1429 * algorithm.
1430 * Note that this requires that the driver implement a number of
1431 * callbacks so it has the correct information, it needs to have
1432 * the @set_rts_threshold callback and must look at the BSS config
1433 * @use_cts_prot for G/N protection, @use_short_slot for slot
1434 * timing in 2.4 GHz and @use_short_preamble for preambles for
1435 * CCK frames.
1436 *
1437 * @IEEE80211_HW_RX_INCLUDES_FCS:
1438 * Indicates that received frames passed to the stack include
1439 * the FCS at the end.
1440 *
1441 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING:
1442 * Some wireless LAN chipsets buffer broadcast/multicast frames
1443 * for power saving stations in the hardware/firmware and others
1444 * rely on the host system for such buffering. This option is used
1445 * to configure the IEEE 802.11 upper layer to buffer broadcast and
1446 * multicast frames when there are power saving stations so that
1447 * the driver can fetch them with ieee80211_get_buffered_bc().
1448 *
1449 * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE:
1450 * Hardware is not capable of short slot operation on the 2.4 GHz band.
1451 *
1452 * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE:
1453 * Hardware is not capable of receiving frames with short preamble on
1454 * the 2.4 GHz band.
1455 *
1456 * @IEEE80211_HW_SIGNAL_UNSPEC:
1457 * Hardware can provide signal values but we don't know its units. We
1458 * expect values between 0 and @max_signal.
1459 * If possible please provide dB or dBm instead.
1460 *
1461 * @IEEE80211_HW_SIGNAL_DBM:
1462 * Hardware gives signal values in dBm, decibel difference from
1463 * one milliwatt. This is the preferred method since it is standardized
1464 * between different devices. @max_signal does not need to be set.
1465 *
1466 * @IEEE80211_HW_SPECTRUM_MGMT:
1467 * Hardware supports spectrum management defined in 802.11h
1468 * Measurement, Channel Switch, Quieting, TPC
1469 *
1470 * @IEEE80211_HW_AMPDU_AGGREGATION:
1471 * Hardware supports 11n A-MPDU aggregation.
1472 *
1473 * @IEEE80211_HW_SUPPORTS_PS:
1474 * Hardware has power save support (i.e. can go to sleep).
1475 *
1476 * @IEEE80211_HW_PS_NULLFUNC_STACK:
1477 * Hardware requires nullfunc frame handling in stack, implies
1478 * stack support for dynamic PS.
1479 *
1480 * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS:
1481 * Hardware has support for dynamic PS.
1482 *
1483 * @IEEE80211_HW_MFP_CAPABLE:
1484 * Hardware supports management frame protection (MFP, IEEE 802.11w).
1485 *
1486 * @IEEE80211_HW_SUPPORTS_STATIC_SMPS:
1487 * Hardware supports static spatial multiplexing powersave,
1488 * ie. can turn off all but one chain even on HT connections
1489 * that should be using more chains.
1490 *
1491 * @IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS:
1492 * Hardware supports dynamic spatial multiplexing powersave,
1493 * ie. can turn off all but one chain and then wake the rest
1494 * up as required after, for example, rts/cts handshake.
1495 *
1496 * @IEEE80211_HW_SUPPORTS_UAPSD:
1497 * Hardware supports Unscheduled Automatic Power Save Delivery
1498 * (U-APSD) in managed mode. The mode is configured with
1499 * conf_tx() operation.
1500 *
1501 * @IEEE80211_HW_REPORTS_TX_ACK_STATUS:
1502 * Hardware can provide ack status reports of Tx frames to
1503 * the stack.
1504 *
1505 * @IEEE80211_HW_CONNECTION_MONITOR:
1506 * The hardware performs its own connection monitoring, including
1507 * periodic keep-alives to the AP and probing the AP on beacon loss.
1508 *
1509 * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC:
1510 * This device needs to get data from beacon before association (i.e.
1511 * dtim_period).
1512 *
1513 * @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports
1514 * per-station GTKs as used by IBSS RSN or during fast transition. If
1515 * the device doesn't support per-station GTKs, but can be asked not
1516 * to decrypt group addressed frames, then IBSS RSN support is still
1517 * possible but software crypto will be used. Advertise the wiphy flag
1518 * only in that case.
1519 *
1520 * @IEEE80211_HW_AP_LINK_PS: When operating in AP mode the device
1521 * autonomously manages the PS status of connected stations. When
1522 * this flag is set mac80211 will not trigger PS mode for connected
1523 * stations based on the PM bit of incoming frames.
1524 * Use ieee80211_start_ps()/ieee8021_end_ps() to manually configure
1525 * the PS mode of connected stations.
1526 *
1527 * @IEEE80211_HW_TX_AMPDU_SETUP_IN_HW: The device handles TX A-MPDU session
1528 * setup strictly in HW. mac80211 should not attempt to do this in
1529 * software.
1530 *
1531 * @IEEE80211_HW_WANT_MONITOR_VIF: The driver would like to be informed of
1532 * a virtual monitor interface when monitor interfaces are the only
1533 * active interfaces.
1534 *
1535 * @IEEE80211_HW_QUEUE_CONTROL: The driver wants to control per-interface
1536 * queue mapping in order to use different queues (not just one per AC)
1537 * for different virtual interfaces. See the doc section on HW queue
1538 * control for more details.
1539 *
1540 * @IEEE80211_HW_SUPPORTS_RC_TABLE: The driver supports using a rate
1541 * selection table provided by the rate control algorithm.
1542 *
1543 * @IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF: Use the P2P Device address for any
1544 * P2P Interface. This will be honoured even if more than one interface
1545 * is supported.
1546 *
1547 * @IEEE80211_HW_TIMING_BEACON_ONLY: Use sync timing from beacon frames
1548 * only, to allow getting TBTT of a DTIM beacon.
1549 *
1550 * @IEEE80211_HW_SUPPORTS_HT_CCK_RATES: Hardware supports mixing HT/CCK rates
1551 * and can cope with CCK rates in an aggregation session (e.g. by not
1552 * using aggregation for such frames.)
1553 *
1554 * @IEEE80211_HW_CHANCTX_STA_CSA: Support 802.11h based channel-switch (CSA)
1555 * for a single active channel while using channel contexts. When support
1556 * is not enabled the default action is to disconnect when getting the
1557 * CSA frame.
1558 */
1559enum ieee80211_hw_flags {
1560 IEEE80211_HW_HAS_RATE_CONTROL = 1<<0,
1561 IEEE80211_HW_RX_INCLUDES_FCS = 1<<1,
1562 IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2,
1563 IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3,
1564 IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4,
1565 IEEE80211_HW_SIGNAL_UNSPEC = 1<<5,
1566 IEEE80211_HW_SIGNAL_DBM = 1<<6,
1567 IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC = 1<<7,
1568 IEEE80211_HW_SPECTRUM_MGMT = 1<<8,
1569 IEEE80211_HW_AMPDU_AGGREGATION = 1<<9,
1570 IEEE80211_HW_SUPPORTS_PS = 1<<10,
1571 IEEE80211_HW_PS_NULLFUNC_STACK = 1<<11,
1572 IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12,
1573 IEEE80211_HW_MFP_CAPABLE = 1<<13,
1574 IEEE80211_HW_WANT_MONITOR_VIF = 1<<14,
1575 IEEE80211_HW_SUPPORTS_STATIC_SMPS = 1<<15,
1576 IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS = 1<<16,
1577 IEEE80211_HW_SUPPORTS_UAPSD = 1<<17,
1578 IEEE80211_HW_REPORTS_TX_ACK_STATUS = 1<<18,
1579 IEEE80211_HW_CONNECTION_MONITOR = 1<<19,
1580 IEEE80211_HW_QUEUE_CONTROL = 1<<20,
1581 IEEE80211_HW_SUPPORTS_PER_STA_GTK = 1<<21,
1582 IEEE80211_HW_AP_LINK_PS = 1<<22,
1583 IEEE80211_HW_TX_AMPDU_SETUP_IN_HW = 1<<23,
1584 IEEE80211_HW_SUPPORTS_RC_TABLE = 1<<24,
1585 IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF = 1<<25,
1586 IEEE80211_HW_TIMING_BEACON_ONLY = 1<<26,
1587 IEEE80211_HW_SUPPORTS_HT_CCK_RATES = 1<<27,
1588 IEEE80211_HW_CHANCTX_STA_CSA = 1<<28,
1589};
1590
1591/**
1592 * struct ieee80211_hw - hardware information and state
1593 *
1594 * This structure contains the configuration and hardware
1595 * information for an 802.11 PHY.
1596 *
1597 * @wiphy: This points to the &struct wiphy allocated for this
1598 * 802.11 PHY. You must fill in the @perm_addr and @dev
1599 * members of this structure using SET_IEEE80211_DEV()
1600 * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported
1601 * bands (with channels, bitrates) are registered here.
1602 *
1603 * @conf: &struct ieee80211_conf, device configuration, don't use.
1604 *
1605 * @priv: pointer to private area that was allocated for driver use
1606 * along with this structure.
1607 *
1608 * @flags: hardware flags, see &enum ieee80211_hw_flags.
1609 *
1610 * @extra_tx_headroom: headroom to reserve in each transmit skb
1611 * for use by the driver (e.g. for transmit headers.)
1612 *
1613 * @extra_beacon_tailroom: tailroom to reserve in each beacon tx skb.
1614 * Can be used by drivers to add extra IEs.
1615 *
1616 * @max_signal: Maximum value for signal (rssi) in RX information, used
1617 * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
1618 *
1619 * @max_listen_interval: max listen interval in units of beacon interval
1620 * that HW supports
1621 *
1622 * @queues: number of available hardware transmit queues for
1623 * data packets. WMM/QoS requires at least four, these
1624 * queues need to have configurable access parameters.
1625 *
1626 * @rate_control_algorithm: rate control algorithm for this hardware.
1627 * If unset (NULL), the default algorithm will be used. Must be
1628 * set before calling ieee80211_register_hw().
1629 *
1630 * @vif_data_size: size (in bytes) of the drv_priv data area
1631 * within &struct ieee80211_vif.
1632 * @sta_data_size: size (in bytes) of the drv_priv data area
1633 * within &struct ieee80211_sta.
1634 * @chanctx_data_size: size (in bytes) of the drv_priv data area
1635 * within &struct ieee80211_chanctx_conf.
1636 *
1637 * @max_rates: maximum number of alternate rate retry stages the hw
1638 * can handle.
1639 * @max_report_rates: maximum number of alternate rate retry stages
1640 * the hw can report back.
1641 * @max_rate_tries: maximum number of tries for each stage
1642 *
1643 * @max_rx_aggregation_subframes: maximum buffer size (number of
1644 * sub-frames) to be used for A-MPDU block ack receiver
1645 * aggregation.
1646 * This is only relevant if the device has restrictions on the
1647 * number of subframes, if it relies on mac80211 to do reordering
1648 * it shouldn't be set.
1649 *
1650 * @max_tx_aggregation_subframes: maximum number of subframes in an
1651 * aggregate an HT driver will transmit, used by the peer as a
1652 * hint to size its reorder buffer.
1653 *
1654 * @offchannel_tx_hw_queue: HW queue ID to use for offchannel TX
1655 * (if %IEEE80211_HW_QUEUE_CONTROL is set)
1656 *
1657 * @radiotap_mcs_details: lists which MCS information can the HW
1658 * reports, by default it is set to _MCS, _GI and _BW but doesn't
1659 * include _FMT. Use %IEEE80211_RADIOTAP_MCS_HAVE_* values, only
1660 * adding _BW is supported today.
1661 *
1662 * @radiotap_vht_details: lists which VHT MCS information the HW reports,
1663 * the default is _GI | _BANDWIDTH.
1664 * Use the %IEEE80211_RADIOTAP_VHT_KNOWN_* values.
1665 *
1666 * @netdev_features: netdev features to be set in each netdev created
1667 * from this HW. Note only HW checksum features are currently
1668 * compatible with mac80211. Other feature bits will be rejected.
1669 *
1670 * @uapsd_queues: This bitmap is included in (re)association frame to indicate
1671 * for each access category if it is uAPSD trigger-enabled and delivery-
1672 * enabled. Use IEEE80211_WMM_IE_STA_QOSINFO_AC_* to set this bitmap.
1673 * Each bit corresponds to different AC. Value '1' in specific bit means
1674 * that corresponding AC is both trigger- and delivery-enabled. '0' means
1675 * neither enabled.
1676 *
1677 * @uapsd_max_sp_len: maximum number of total buffered frames the WMM AP may
1678 * deliver to a WMM STA during any Service Period triggered by the WMM STA.
1679 * Use IEEE80211_WMM_IE_STA_QOSINFO_SP_* for correct values.
1680 *
1681 * @n_cipher_schemes: a size of an array of cipher schemes definitions.
1682 * @cipher_schemes: a pointer to an array of cipher scheme definitions
1683 * supported by HW.
1684 */
1685struct ieee80211_hw {
1686 struct ieee80211_conf conf;
1687 struct wiphy *wiphy;
1688 const char *rate_control_algorithm;
1689 void *priv;
1690 u32 flags;
1691 unsigned int extra_tx_headroom;
1692 unsigned int extra_beacon_tailroom;
1693 int vif_data_size;
1694 int sta_data_size;
1695 int chanctx_data_size;
1696 u16 queues;
1697 u16 max_listen_interval;
1698 s8 max_signal;
1699 u8 max_rates;
1700 u8 max_report_rates;
1701 u8 max_rate_tries;
1702 u8 max_rx_aggregation_subframes;
1703 u8 max_tx_aggregation_subframes;
1704 u8 offchannel_tx_hw_queue;
1705 u8 radiotap_mcs_details;
1706 u16 radiotap_vht_details;
1707 netdev_features_t netdev_features;
1708 u8 uapsd_queues;
1709 u8 uapsd_max_sp_len;
1710 u8 n_cipher_schemes;
1711 const struct ieee80211_cipher_scheme *cipher_schemes;
1712};
1713
1714/**
1715 * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy
1716 *
1717 * @wiphy: the &struct wiphy which we want to query
1718 *
1719 * mac80211 drivers can use this to get to their respective
1720 * &struct ieee80211_hw. Drivers wishing to get to their own private
1721 * structure can then access it via hw->priv. Note that mac802111 drivers should
1722 * not use wiphy_priv() to try to get their private driver structure as this
1723 * is already used internally by mac80211.
1724 *
1725 * Return: The mac80211 driver hw struct of @wiphy.
1726 */
1727struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy);
1728
1729/**
1730 * SET_IEEE80211_DEV - set device for 802.11 hardware
1731 *
1732 * @hw: the &struct ieee80211_hw to set the device for
1733 * @dev: the &struct device of this 802.11 device
1734 */
1735static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev)
1736{
1737 set_wiphy_dev(hw->wiphy, dev);
1738}
1739
1740/**
1741 * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware
1742 *
1743 * @hw: the &struct ieee80211_hw to set the MAC address for
1744 * @addr: the address to set
1745 */
1746static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr)
1747{
1748 memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN);
1749}
1750
1751static inline struct ieee80211_rate *
1752ieee80211_get_tx_rate(const struct ieee80211_hw *hw,
1753 const struct ieee80211_tx_info *c)
1754{
1755 if (WARN_ON_ONCE(c->control.rates[0].idx < 0))
1756 return NULL;
1757 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx];
1758}
1759
1760static inline struct ieee80211_rate *
1761ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw,
1762 const struct ieee80211_tx_info *c)
1763{
1764 if (c->control.rts_cts_rate_idx < 0)
1765 return NULL;
1766 return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx];
1767}
1768
1769static inline struct ieee80211_rate *
1770ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
1771 const struct ieee80211_tx_info *c, int idx)
1772{
1773 if (c->control.rates[idx + 1].idx < 0)
1774 return NULL;
1775 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx];
1776}
1777
1778/**
1779 * ieee80211_free_txskb - free TX skb
1780 * @hw: the hardware
1781 * @skb: the skb
1782 *
1783 * Free a transmit skb. Use this funtion when some failure
1784 * to transmit happened and thus status cannot be reported.
1785 */
1786void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb);
1787
1788/**
1789 * DOC: Hardware crypto acceleration
1790 *
1791 * mac80211 is capable of taking advantage of many hardware
1792 * acceleration designs for encryption and decryption operations.
1793 *
1794 * The set_key() callback in the &struct ieee80211_ops for a given
1795 * device is called to enable hardware acceleration of encryption and
1796 * decryption. The callback takes a @sta parameter that will be NULL
1797 * for default keys or keys used for transmission only, or point to
1798 * the station information for the peer for individual keys.
1799 * Multiple transmission keys with the same key index may be used when
1800 * VLANs are configured for an access point.
1801 *
1802 * When transmitting, the TX control data will use the @hw_key_idx
1803 * selected by the driver by modifying the &struct ieee80211_key_conf
1804 * pointed to by the @key parameter to the set_key() function.
1805 *
1806 * The set_key() call for the %SET_KEY command should return 0 if
1807 * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be
1808 * added; if you return 0 then hw_key_idx must be assigned to the
1809 * hardware key index, you are free to use the full u8 range.
1810 *
1811 * When the cmd is %DISABLE_KEY then it must succeed.
1812 *
1813 * Note that it is permissible to not decrypt a frame even if a key
1814 * for it has been uploaded to hardware, the stack will not make any
1815 * decision based on whether a key has been uploaded or not but rather
1816 * based on the receive flags.
1817 *
1818 * The &struct ieee80211_key_conf structure pointed to by the @key
1819 * parameter is guaranteed to be valid until another call to set_key()
1820 * removes it, but it can only be used as a cookie to differentiate
1821 * keys.
1822 *
1823 * In TKIP some HW need to be provided a phase 1 key, for RX decryption
1824 * acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key
1825 * handler.
1826 * The update_tkip_key() call updates the driver with the new phase 1 key.
1827 * This happens every time the iv16 wraps around (every 65536 packets). The
1828 * set_key() call will happen only once for each key (unless the AP did
1829 * rekeying), it will not include a valid phase 1 key. The valid phase 1 key is
1830 * provided by update_tkip_key only. The trigger that makes mac80211 call this
1831 * handler is software decryption with wrap around of iv16.
1832 *
1833 * The set_default_unicast_key() call updates the default WEP key index
1834 * configured to the hardware for WEP encryption type. This is required
1835 * for devices that support offload of data packets (e.g. ARP responses).
1836 */
1837
1838/**
1839 * DOC: Powersave support
1840 *
1841 * mac80211 has support for various powersave implementations.
1842 *
1843 * First, it can support hardware that handles all powersaving by itself,
1844 * such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS hardware
1845 * flag. In that case, it will be told about the desired powersave mode
1846 * with the %IEEE80211_CONF_PS flag depending on the association status.
1847 * The hardware must take care of sending nullfunc frames when necessary,
1848 * i.e. when entering and leaving powersave mode. The hardware is required
1849 * to look at the AID in beacons and signal to the AP that it woke up when
1850 * it finds traffic directed to it.
1851 *
1852 * %IEEE80211_CONF_PS flag enabled means that the powersave mode defined in
1853 * IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused
1854 * with hardware wakeup and sleep states. Driver is responsible for waking
1855 * up the hardware before issuing commands to the hardware and putting it
1856 * back to sleep at appropriate times.
1857 *
1858 * When PS is enabled, hardware needs to wakeup for beacons and receive the
1859 * buffered multicast/broadcast frames after the beacon. Also it must be
1860 * possible to send frames and receive the acknowledment frame.
1861 *
1862 * Other hardware designs cannot send nullfunc frames by themselves and also
1863 * need software support for parsing the TIM bitmap. This is also supported
1864 * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and
1865 * %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still
1866 * required to pass up beacons. The hardware is still required to handle
1867 * waking up for multicast traffic; if it cannot the driver must handle that
1868 * as best as it can, mac80211 is too slow to do that.
1869 *
1870 * Dynamic powersave is an extension to normal powersave in which the
1871 * hardware stays awake for a user-specified period of time after sending a
1872 * frame so that reply frames need not be buffered and therefore delayed to
1873 * the next wakeup. It's compromise of getting good enough latency when
1874 * there's data traffic and still saving significantly power in idle
1875 * periods.
1876 *
1877 * Dynamic powersave is simply supported by mac80211 enabling and disabling
1878 * PS based on traffic. Driver needs to only set %IEEE80211_HW_SUPPORTS_PS
1879 * flag and mac80211 will handle everything automatically. Additionally,
1880 * hardware having support for the dynamic PS feature may set the
1881 * %IEEE80211_HW_SUPPORTS_DYNAMIC_PS flag to indicate that it can support
1882 * dynamic PS mode itself. The driver needs to look at the
1883 * @dynamic_ps_timeout hardware configuration value and use it that value
1884 * whenever %IEEE80211_CONF_PS is set. In this case mac80211 will disable
1885 * dynamic PS feature in stack and will just keep %IEEE80211_CONF_PS
1886 * enabled whenever user has enabled powersave.
1887 *
1888 * Driver informs U-APSD client support by enabling
1889 * %IEEE80211_HW_SUPPORTS_UAPSD flag. The mode is configured through the
1890 * uapsd parameter in conf_tx() operation. Hardware needs to send the QoS
1891 * Nullfunc frames and stay awake until the service period has ended. To
1892 * utilize U-APSD, dynamic powersave is disabled for voip AC and all frames
1893 * from that AC are transmitted with powersave enabled.
1894 *
1895 * Note: U-APSD client mode is not yet supported with
1896 * %IEEE80211_HW_PS_NULLFUNC_STACK.
1897 */
1898
1899/**
1900 * DOC: Beacon filter support
1901 *
1902 * Some hardware have beacon filter support to reduce host cpu wakeups
1903 * which will reduce system power consumption. It usually works so that
1904 * the firmware creates a checksum of the beacon but omits all constantly
1905 * changing elements (TSF, TIM etc). Whenever the checksum changes the
1906 * beacon is forwarded to the host, otherwise it will be just dropped. That
1907 * way the host will only receive beacons where some relevant information
1908 * (for example ERP protection or WMM settings) have changed.
1909 *
1910 * Beacon filter support is advertised with the %IEEE80211_VIF_BEACON_FILTER
1911 * interface capability. The driver needs to enable beacon filter support
1912 * whenever power save is enabled, that is %IEEE80211_CONF_PS is set. When
1913 * power save is enabled, the stack will not check for beacon loss and the
1914 * driver needs to notify about loss of beacons with ieee80211_beacon_loss().
1915 *
1916 * The time (or number of beacons missed) until the firmware notifies the
1917 * driver of a beacon loss event (which in turn causes the driver to call
1918 * ieee80211_beacon_loss()) should be configurable and will be controlled
1919 * by mac80211 and the roaming algorithm in the future.
1920 *
1921 * Since there may be constantly changing information elements that nothing
1922 * in the software stack cares about, we will, in the future, have mac80211
1923 * tell the driver which information elements are interesting in the sense
1924 * that we want to see changes in them. This will include
1925 * - a list of information element IDs
1926 * - a list of OUIs for the vendor information element
1927 *
1928 * Ideally, the hardware would filter out any beacons without changes in the
1929 * requested elements, but if it cannot support that it may, at the expense
1930 * of some efficiency, filter out only a subset. For example, if the device
1931 * doesn't support checking for OUIs it should pass up all changes in all
1932 * vendor information elements.
1933 *
1934 * Note that change, for the sake of simplification, also includes information
1935 * elements appearing or disappearing from the beacon.
1936 *
1937 * Some hardware supports an "ignore list" instead, just make sure nothing
1938 * that was requested is on the ignore list, and include commonly changing
1939 * information element IDs in the ignore list, for example 11 (BSS load) and
1940 * the various vendor-assigned IEs with unknown contents (128, 129, 133-136,
1941 * 149, 150, 155, 156, 173, 176, 178, 179, 219); for forward compatibility
1942 * it could also include some currently unused IDs.
1943 *
1944 *
1945 * In addition to these capabilities, hardware should support notifying the
1946 * host of changes in the beacon RSSI. This is relevant to implement roaming
1947 * when no traffic is flowing (when traffic is flowing we see the RSSI of
1948 * the received data packets). This can consist in notifying the host when
1949 * the RSSI changes significantly or when it drops below or rises above
1950 * configurable thresholds. In the future these thresholds will also be
1951 * configured by mac80211 (which gets them from userspace) to implement
1952 * them as the roaming algorithm requires.
1953 *
1954 * If the hardware cannot implement this, the driver should ask it to
1955 * periodically pass beacon frames to the host so that software can do the
1956 * signal strength threshold checking.
1957 */
1958
1959/**
1960 * DOC: Spatial multiplexing power save
1961 *
1962 * SMPS (Spatial multiplexing power save) is a mechanism to conserve
1963 * power in an 802.11n implementation. For details on the mechanism
1964 * and rationale, please refer to 802.11 (as amended by 802.11n-2009)
1965 * "11.2.3 SM power save".
1966 *
1967 * The mac80211 implementation is capable of sending action frames
1968 * to update the AP about the station's SMPS mode, and will instruct
1969 * the driver to enter the specific mode. It will also announce the
1970 * requested SMPS mode during the association handshake. Hardware
1971 * support for this feature is required, and can be indicated by
1972 * hardware flags.
1973 *
1974 * The default mode will be "automatic", which nl80211/cfg80211
1975 * defines to be dynamic SMPS in (regular) powersave, and SMPS
1976 * turned off otherwise.
1977 *
1978 * To support this feature, the driver must set the appropriate
1979 * hardware support flags, and handle the SMPS flag to the config()
1980 * operation. It will then with this mechanism be instructed to
1981 * enter the requested SMPS mode while associated to an HT AP.
1982 */
1983
1984/**
1985 * DOC: Frame filtering
1986 *
1987 * mac80211 requires to see many management frames for proper
1988 * operation, and users may want to see many more frames when
1989 * in monitor mode. However, for best CPU usage and power consumption,
1990 * having as few frames as possible percolate through the stack is
1991 * desirable. Hence, the hardware should filter as much as possible.
1992 *
1993 * To achieve this, mac80211 uses filter flags (see below) to tell
1994 * the driver's configure_filter() function which frames should be
1995 * passed to mac80211 and which should be filtered out.
1996 *
1997 * Before configure_filter() is invoked, the prepare_multicast()
1998 * callback is invoked with the parameters @mc_count and @mc_list
1999 * for the combined multicast address list of all virtual interfaces.
2000 * It's use is optional, and it returns a u64 that is passed to
2001 * configure_filter(). Additionally, configure_filter() has the
2002 * arguments @changed_flags telling which flags were changed and
2003 * @total_flags with the new flag states.
2004 *
2005 * If your device has no multicast address filters your driver will
2006 * need to check both the %FIF_ALLMULTI flag and the @mc_count
2007 * parameter to see whether multicast frames should be accepted
2008 * or dropped.
2009 *
2010 * All unsupported flags in @total_flags must be cleared.
2011 * Hardware does not support a flag if it is incapable of _passing_
2012 * the frame to the stack. Otherwise the driver must ignore
2013 * the flag, but not clear it.
2014 * You must _only_ clear the flag (announce no support for the
2015 * flag to mac80211) if you are not able to pass the packet type
2016 * to the stack (so the hardware always filters it).
2017 * So for example, you should clear @FIF_CONTROL, if your hardware
2018 * always filters control frames. If your hardware always passes
2019 * control frames to the kernel and is incapable of filtering them,
2020 * you do _not_ clear the @FIF_CONTROL flag.
2021 * This rule applies to all other FIF flags as well.
2022 */
2023
2024/**
2025 * DOC: AP support for powersaving clients
2026 *
2027 * In order to implement AP and P2P GO modes, mac80211 has support for
2028 * client powersaving, both "legacy" PS (PS-Poll/null data) and uAPSD.
2029 * There currently is no support for sAPSD.
2030 *
2031 * There is one assumption that mac80211 makes, namely that a client
2032 * will not poll with PS-Poll and trigger with uAPSD at the same time.
2033 * Both are supported, and both can be used by the same client, but
2034 * they can't be used concurrently by the same client. This simplifies
2035 * the driver code.
2036 *
2037 * The first thing to keep in mind is that there is a flag for complete
2038 * driver implementation: %IEEE80211_HW_AP_LINK_PS. If this flag is set,
2039 * mac80211 expects the driver to handle most of the state machine for
2040 * powersaving clients and will ignore the PM bit in incoming frames.
2041 * Drivers then use ieee80211_sta_ps_transition() to inform mac80211 of
2042 * stations' powersave transitions. In this mode, mac80211 also doesn't
2043 * handle PS-Poll/uAPSD.
2044 *
2045 * In the mode without %IEEE80211_HW_AP_LINK_PS, mac80211 will check the
2046 * PM bit in incoming frames for client powersave transitions. When a
2047 * station goes to sleep, we will stop transmitting to it. There is,
2048 * however, a race condition: a station might go to sleep while there is
2049 * data buffered on hardware queues. If the device has support for this
2050 * it will reject frames, and the driver should give the frames back to
2051 * mac80211 with the %IEEE80211_TX_STAT_TX_FILTERED flag set which will
2052 * cause mac80211 to retry the frame when the station wakes up. The
2053 * driver is also notified of powersave transitions by calling its
2054 * @sta_notify callback.
2055 *
2056 * When the station is asleep, it has three choices: it can wake up,
2057 * it can PS-Poll, or it can possibly start a uAPSD service period.
2058 * Waking up is implemented by simply transmitting all buffered (and
2059 * filtered) frames to the station. This is the easiest case. When
2060 * the station sends a PS-Poll or a uAPSD trigger frame, mac80211
2061 * will inform the driver of this with the @allow_buffered_frames
2062 * callback; this callback is optional. mac80211 will then transmit
2063 * the frames as usual and set the %IEEE80211_TX_CTL_NO_PS_BUFFER
2064 * on each frame. The last frame in the service period (or the only
2065 * response to a PS-Poll) also has %IEEE80211_TX_STATUS_EOSP set to
2066 * indicate that it ends the service period; as this frame must have
2067 * TX status report it also sets %IEEE80211_TX_CTL_REQ_TX_STATUS.
2068 * When TX status is reported for this frame, the service period is
2069 * marked has having ended and a new one can be started by the peer.
2070 *
2071 * Additionally, non-bufferable MMPDUs can also be transmitted by
2072 * mac80211 with the %IEEE80211_TX_CTL_NO_PS_BUFFER set in them.
2073 *
2074 * Another race condition can happen on some devices like iwlwifi
2075 * when there are frames queued for the station and it wakes up
2076 * or polls; the frames that are already queued could end up being
2077 * transmitted first instead, causing reordering and/or wrong
2078 * processing of the EOSP. The cause is that allowing frames to be
2079 * transmitted to a certain station is out-of-band communication to
2080 * the device. To allow this problem to be solved, the driver can
2081 * call ieee80211_sta_block_awake() if frames are buffered when it
2082 * is notified that the station went to sleep. When all these frames
2083 * have been filtered (see above), it must call the function again
2084 * to indicate that the station is no longer blocked.
2085 *
2086 * If the driver buffers frames in the driver for aggregation in any
2087 * way, it must use the ieee80211_sta_set_buffered() call when it is
2088 * notified of the station going to sleep to inform mac80211 of any
2089 * TIDs that have frames buffered. Note that when a station wakes up
2090 * this information is reset (hence the requirement to call it when
2091 * informed of the station going to sleep). Then, when a service
2092 * period starts for any reason, @release_buffered_frames is called
2093 * with the number of frames to be released and which TIDs they are
2094 * to come from. In this case, the driver is responsible for setting
2095 * the EOSP (for uAPSD) and MORE_DATA bits in the released frames,
2096 * to help the @more_data parameter is passed to tell the driver if
2097 * there is more data on other TIDs -- the TIDs to release frames
2098 * from are ignored since mac80211 doesn't know how many frames the
2099 * buffers for those TIDs contain.
2100 *
2101 * If the driver also implement GO mode, where absence periods may
2102 * shorten service periods (or abort PS-Poll responses), it must
2103 * filter those response frames except in the case of frames that
2104 * are buffered in the driver -- those must remain buffered to avoid
2105 * reordering. Because it is possible that no frames are released
2106 * in this case, the driver must call ieee80211_sta_eosp()
2107 * to indicate to mac80211 that the service period ended anyway.
2108 *
2109 * Finally, if frames from multiple TIDs are released from mac80211
2110 * but the driver might reorder them, it must clear & set the flags
2111 * appropriately (only the last frame may have %IEEE80211_TX_STATUS_EOSP)
2112 * and also take care of the EOSP and MORE_DATA bits in the frame.
2113 * The driver may also use ieee80211_sta_eosp() in this case.
2114 *
2115 * Note that if the driver ever buffers frames other than QoS-data
2116 * frames, it must take care to never send a non-QoS-data frame as
2117 * the last frame in a service period, adding a QoS-nulldata frame
2118 * after a non-QoS-data frame if needed.
2119 */
2120
2121/**
2122 * DOC: HW queue control
2123 *
2124 * Before HW queue control was introduced, mac80211 only had a single static
2125 * assignment of per-interface AC software queues to hardware queues. This
2126 * was problematic for a few reasons:
2127 * 1) off-channel transmissions might get stuck behind other frames
2128 * 2) multiple virtual interfaces couldn't be handled correctly
2129 * 3) after-DTIM frames could get stuck behind other frames
2130 *
2131 * To solve this, hardware typically uses multiple different queues for all
2132 * the different usages, and this needs to be propagated into mac80211 so it
2133 * won't have the same problem with the software queues.
2134 *
2135 * Therefore, mac80211 now offers the %IEEE80211_HW_QUEUE_CONTROL capability
2136 * flag that tells it that the driver implements its own queue control. To do
2137 * so, the driver will set up the various queues in each &struct ieee80211_vif
2138 * and the offchannel queue in &struct ieee80211_hw. In response, mac80211 will
2139 * use those queue IDs in the hw_queue field of &struct ieee80211_tx_info and
2140 * if necessary will queue the frame on the right software queue that mirrors
2141 * the hardware queue.
2142 * Additionally, the driver has to then use these HW queue IDs for the queue
2143 * management functions (ieee80211_stop_queue() et al.)
2144 *
2145 * The driver is free to set up the queue mappings as needed, multiple virtual
2146 * interfaces may map to the same hardware queues if needed. The setup has to
2147 * happen during add_interface or change_interface callbacks. For example, a
2148 * driver supporting station+station and station+AP modes might decide to have
2149 * 10 hardware queues to handle different scenarios:
2150 *
2151 * 4 AC HW queues for 1st vif: 0, 1, 2, 3
2152 * 4 AC HW queues for 2nd vif: 4, 5, 6, 7
2153 * after-DTIM queue for AP: 8
2154 * off-channel queue: 9
2155 *
2156 * It would then set up the hardware like this:
2157 * hw.offchannel_tx_hw_queue = 9
2158 *
2159 * and the first virtual interface that is added as follows:
2160 * vif.hw_queue[IEEE80211_AC_VO] = 0
2161 * vif.hw_queue[IEEE80211_AC_VI] = 1
2162 * vif.hw_queue[IEEE80211_AC_BE] = 2
2163 * vif.hw_queue[IEEE80211_AC_BK] = 3
2164 * vif.cab_queue = 8 // if AP mode, otherwise %IEEE80211_INVAL_HW_QUEUE
2165 * and the second virtual interface with 4-7.
2166 *
2167 * If queue 6 gets full, for example, mac80211 would only stop the second
2168 * virtual interface's BE queue since virtual interface queues are per AC.
2169 *
2170 * Note that the vif.cab_queue value should be set to %IEEE80211_INVAL_HW_QUEUE
2171 * whenever the queue is not used (i.e. the interface is not in AP mode) if the
2172 * queue could potentially be shared since mac80211 will look at cab_queue when
2173 * a queue is stopped/woken even if the interface is not in AP mode.
2174 */
2175
2176/**
2177 * enum ieee80211_filter_flags - hardware filter flags
2178 *
2179 * These flags determine what the filter in hardware should be
2180 * programmed to let through and what should not be passed to the
2181 * stack. It is always safe to pass more frames than requested,
2182 * but this has negative impact on power consumption.
2183 *
2184 * @FIF_PROMISC_IN_BSS: promiscuous mode within your BSS,
2185 * think of the BSS as your network segment and then this corresponds
2186 * to the regular ethernet device promiscuous mode.
2187 *
2188 * @FIF_ALLMULTI: pass all multicast frames, this is used if requested
2189 * by the user or if the hardware is not capable of filtering by
2190 * multicast address.
2191 *
2192 * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the
2193 * %RX_FLAG_FAILED_FCS_CRC for them)
2194 *
2195 * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set
2196 * the %RX_FLAG_FAILED_PLCP_CRC for them
2197 *
2198 * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate
2199 * to the hardware that it should not filter beacons or probe responses
2200 * by BSSID. Filtering them can greatly reduce the amount of processing
2201 * mac80211 needs to do and the amount of CPU wakeups, so you should
2202 * honour this flag if possible.
2203 *
2204 * @FIF_CONTROL: pass control frames (except for PS Poll), if PROMISC_IN_BSS
2205 * is not set then only those addressed to this station.
2206 *
2207 * @FIF_OTHER_BSS: pass frames destined to other BSSes
2208 *
2209 * @FIF_PSPOLL: pass PS Poll frames, if PROMISC_IN_BSS is not set then only
2210 * those addressed to this station.
2211 *
2212 * @FIF_PROBE_REQ: pass probe request frames
2213 */
2214enum ieee80211_filter_flags {
2215 FIF_PROMISC_IN_BSS = 1<<0,
2216 FIF_ALLMULTI = 1<<1,
2217 FIF_FCSFAIL = 1<<2,
2218 FIF_PLCPFAIL = 1<<3,
2219 FIF_BCN_PRBRESP_PROMISC = 1<<4,
2220 FIF_CONTROL = 1<<5,
2221 FIF_OTHER_BSS = 1<<6,
2222 FIF_PSPOLL = 1<<7,
2223 FIF_PROBE_REQ = 1<<8,
2224};
2225
2226/**
2227 * enum ieee80211_ampdu_mlme_action - A-MPDU actions
2228 *
2229 * These flags are used with the ampdu_action() callback in
2230 * &struct ieee80211_ops to indicate which action is needed.
2231 *
2232 * Note that drivers MUST be able to deal with a TX aggregation
2233 * session being stopped even before they OK'ed starting it by
2234 * calling ieee80211_start_tx_ba_cb_irqsafe, because the peer
2235 * might receive the addBA frame and send a delBA right away!
2236 *
2237 * @IEEE80211_AMPDU_RX_START: start RX aggregation
2238 * @IEEE80211_AMPDU_RX_STOP: stop RX aggregation
2239 * @IEEE80211_AMPDU_TX_START: start TX aggregation
2240 * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational
2241 * @IEEE80211_AMPDU_TX_STOP_CONT: stop TX aggregation but continue transmitting
2242 * queued packets, now unaggregated. After all packets are transmitted the
2243 * driver has to call ieee80211_stop_tx_ba_cb_irqsafe().
2244 * @IEEE80211_AMPDU_TX_STOP_FLUSH: stop TX aggregation and flush all packets,
2245 * called when the station is removed. There's no need or reason to call
2246 * ieee80211_stop_tx_ba_cb_irqsafe() in this case as mac80211 assumes the
2247 * session is gone and removes the station.
2248 * @IEEE80211_AMPDU_TX_STOP_FLUSH_CONT: called when TX aggregation is stopped
2249 * but the driver hasn't called ieee80211_stop_tx_ba_cb_irqsafe() yet and
2250 * now the connection is dropped and the station will be removed. Drivers
2251 * should clean up and drop remaining packets when this is called.
2252 */
2253enum ieee80211_ampdu_mlme_action {
2254 IEEE80211_AMPDU_RX_START,
2255 IEEE80211_AMPDU_RX_STOP,
2256 IEEE80211_AMPDU_TX_START,
2257 IEEE80211_AMPDU_TX_STOP_CONT,
2258 IEEE80211_AMPDU_TX_STOP_FLUSH,
2259 IEEE80211_AMPDU_TX_STOP_FLUSH_CONT,
2260 IEEE80211_AMPDU_TX_OPERATIONAL,
2261};
2262
2263/**
2264 * enum ieee80211_frame_release_type - frame release reason
2265 * @IEEE80211_FRAME_RELEASE_PSPOLL: frame released for PS-Poll
2266 * @IEEE80211_FRAME_RELEASE_UAPSD: frame(s) released due to
2267 * frame received on trigger-enabled AC
2268 */
2269enum ieee80211_frame_release_type {
2270 IEEE80211_FRAME_RELEASE_PSPOLL,
2271 IEEE80211_FRAME_RELEASE_UAPSD,
2272};
2273
2274/**
2275 * enum ieee80211_rate_control_changed - flags to indicate what changed
2276 *
2277 * @IEEE80211_RC_BW_CHANGED: The bandwidth that can be used to transmit
2278 * to this station changed. The actual bandwidth is in the station
2279 * information -- for HT20/40 the IEEE80211_HT_CAP_SUP_WIDTH_20_40
2280 * flag changes, for HT and VHT the bandwidth field changes.
2281 * @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed.
2282 * @IEEE80211_RC_SUPP_RATES_CHANGED: The supported rate set of this peer
2283 * changed (in IBSS mode) due to discovering more information about
2284 * the peer.
2285 * @IEEE80211_RC_NSS_CHANGED: N_SS (number of spatial streams) was changed
2286 * by the peer
2287 */
2288enum ieee80211_rate_control_changed {
2289 IEEE80211_RC_BW_CHANGED = BIT(0),
2290 IEEE80211_RC_SMPS_CHANGED = BIT(1),
2291 IEEE80211_RC_SUPP_RATES_CHANGED = BIT(2),
2292 IEEE80211_RC_NSS_CHANGED = BIT(3),
2293};
2294
2295/**
2296 * enum ieee80211_roc_type - remain on channel type
2297 *
2298 * With the support for multi channel contexts and multi channel operations,
2299 * remain on channel operations might be limited/deferred/aborted by other
2300 * flows/operations which have higher priority (and vise versa).
2301 * Specifying the ROC type can be used by devices to prioritize the ROC
2302 * operations compared to other operations/flows.
2303 *
2304 * @IEEE80211_ROC_TYPE_NORMAL: There are no special requirements for this ROC.
2305 * @IEEE80211_ROC_TYPE_MGMT_TX: The remain on channel request is required
2306 * for sending managment frames offchannel.
2307 */
2308enum ieee80211_roc_type {
2309 IEEE80211_ROC_TYPE_NORMAL = 0,
2310 IEEE80211_ROC_TYPE_MGMT_TX,
2311};
2312
2313/**
2314 * struct ieee80211_ops - callbacks from mac80211 to the driver
2315 *
2316 * This structure contains various callbacks that the driver may
2317 * handle or, in some cases, must handle, for example to configure
2318 * the hardware to a new channel or to transmit a frame.
2319 *
2320 * @tx: Handler that 802.11 module calls for each transmitted frame.
2321 * skb contains the buffer starting from the IEEE 802.11 header.
2322 * The low-level driver should send the frame out based on
2323 * configuration in the TX control data. This handler should,
2324 * preferably, never fail and stop queues appropriately.
2325 * Must be atomic.
2326 *
2327 * @start: Called before the first netdevice attached to the hardware
2328 * is enabled. This should turn on the hardware and must turn on
2329 * frame reception (for possibly enabled monitor interfaces.)
2330 * Returns negative error codes, these may be seen in userspace,
2331 * or zero.
2332 * When the device is started it should not have a MAC address
2333 * to avoid acknowledging frames before a non-monitor device
2334 * is added.
2335 * Must be implemented and can sleep.
2336 *
2337 * @stop: Called after last netdevice attached to the hardware
2338 * is disabled. This should turn off the hardware (at least
2339 * it must turn off frame reception.)
2340 * May be called right after add_interface if that rejects
2341 * an interface. If you added any work onto the mac80211 workqueue
2342 * you should ensure to cancel it on this callback.
2343 * Must be implemented and can sleep.
2344 *
2345 * @suspend: Suspend the device; mac80211 itself will quiesce before and
2346 * stop transmitting and doing any other configuration, and then
2347 * ask the device to suspend. This is only invoked when WoWLAN is
2348 * configured, otherwise the device is deconfigured completely and
2349 * reconfigured at resume time.
2350 * The driver may also impose special conditions under which it
2351 * wants to use the "normal" suspend (deconfigure), say if it only
2352 * supports WoWLAN when the device is associated. In this case, it
2353 * must return 1 from this function.
2354 *
2355 * @resume: If WoWLAN was configured, this indicates that mac80211 is
2356 * now resuming its operation, after this the device must be fully
2357 * functional again. If this returns an error, the only way out is
2358 * to also unregister the device. If it returns 1, then mac80211
2359 * will also go through the regular complete restart on resume.
2360 *
2361 * @set_wakeup: Enable or disable wakeup when WoWLAN configuration is
2362 * modified. The reason is that device_set_wakeup_enable() is
2363 * supposed to be called when the configuration changes, not only
2364 * in suspend().
2365 *
2366 * @add_interface: Called when a netdevice attached to the hardware is
2367 * enabled. Because it is not called for monitor mode devices, @start
2368 * and @stop must be implemented.
2369 * The driver should perform any initialization it needs before
2370 * the device can be enabled. The initial configuration for the
2371 * interface is given in the conf parameter.
2372 * The callback may refuse to add an interface by returning a
2373 * negative error code (which will be seen in userspace.)
2374 * Must be implemented and can sleep.
2375 *
2376 * @change_interface: Called when a netdevice changes type. This callback
2377 * is optional, but only if it is supported can interface types be
2378 * switched while the interface is UP. The callback may sleep.
2379 * Note that while an interface is being switched, it will not be
2380 * found by the interface iteration callbacks.
2381 *
2382 * @remove_interface: Notifies a driver that an interface is going down.
2383 * The @stop callback is called after this if it is the last interface
2384 * and no monitor interfaces are present.
2385 * When all interfaces are removed, the MAC address in the hardware
2386 * must be cleared so the device no longer acknowledges packets,
2387 * the mac_addr member of the conf structure is, however, set to the
2388 * MAC address of the device going away.
2389 * Hence, this callback must be implemented. It can sleep.
2390 *
2391 * @config: Handler for configuration requests. IEEE 802.11 code calls this
2392 * function to change hardware configuration, e.g., channel.
2393 * This function should never fail but returns a negative error code
2394 * if it does. The callback can sleep.
2395 *
2396 * @bss_info_changed: Handler for configuration requests related to BSS
2397 * parameters that may vary during BSS's lifespan, and may affect low
2398 * level driver (e.g. assoc/disassoc status, erp parameters).
2399 * This function should not be used if no BSS has been set, unless
2400 * for association indication. The @changed parameter indicates which
2401 * of the bss parameters has changed when a call is made. The callback
2402 * can sleep.
2403 *
2404 * @prepare_multicast: Prepare for multicast filter configuration.
2405 * This callback is optional, and its return value is passed
2406 * to configure_filter(). This callback must be atomic.
2407 *
2408 * @configure_filter: Configure the device's RX filter.
2409 * See the section "Frame filtering" for more information.
2410 * This callback must be implemented and can sleep.
2411 *
2412 * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit
2413 * must be set or cleared for a given STA. Must be atomic.
2414 *
2415 * @set_key: See the section "Hardware crypto acceleration"
2416 * This callback is only called between add_interface and
2417 * remove_interface calls, i.e. while the given virtual interface
2418 * is enabled.
2419 * Returns a negative error code if the key can't be added.
2420 * The callback can sleep.
2421 *
2422 * @update_tkip_key: See the section "Hardware crypto acceleration"
2423 * This callback will be called in the context of Rx. Called for drivers
2424 * which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY.
2425 * The callback must be atomic.
2426 *
2427 * @set_rekey_data: If the device supports GTK rekeying, for example while the
2428 * host is suspended, it can assign this callback to retrieve the data
2429 * necessary to do GTK rekeying, this is the KEK, KCK and replay counter.
2430 * After rekeying was done it should (for example during resume) notify
2431 * userspace of the new replay counter using ieee80211_gtk_rekey_notify().
2432 *
2433 * @set_default_unicast_key: Set the default (unicast) key index, useful for
2434 * WEP when the device sends data packets autonomously, e.g. for ARP
2435 * offloading. The index can be 0-3, or -1 for unsetting it.
2436 *
2437 * @hw_scan: Ask the hardware to service the scan request, no need to start
2438 * the scan state machine in stack. The scan must honour the channel
2439 * configuration done by the regulatory agent in the wiphy's
2440 * registered bands. The hardware (or the driver) needs to make sure
2441 * that power save is disabled.
2442 * The @req ie/ie_len members are rewritten by mac80211 to contain the
2443 * entire IEs after the SSID, so that drivers need not look at these
2444 * at all but just send them after the SSID -- mac80211 includes the
2445 * (extended) supported rates and HT information (where applicable).
2446 * When the scan finishes, ieee80211_scan_completed() must be called;
2447 * note that it also must be called when the scan cannot finish due to
2448 * any error unless this callback returned a negative error code.
2449 * The callback can sleep.
2450 *
2451 * @cancel_hw_scan: Ask the low-level tp cancel the active hw scan.
2452 * The driver should ask the hardware to cancel the scan (if possible),
2453 * but the scan will be completed only after the driver will call
2454 * ieee80211_scan_completed().
2455 * This callback is needed for wowlan, to prevent enqueueing a new
2456 * scan_work after the low-level driver was already suspended.
2457 * The callback can sleep.
2458 *
2459 * @sched_scan_start: Ask the hardware to start scanning repeatedly at
2460 * specific intervals. The driver must call the
2461 * ieee80211_sched_scan_results() function whenever it finds results.
2462 * This process will continue until sched_scan_stop is called.
2463 *
2464 * @sched_scan_stop: Tell the hardware to stop an ongoing scheduled scan.
2465 * In this case, ieee80211_sched_scan_stopped() must not be called.
2466 *
2467 * @sw_scan_start: Notifier function that is called just before a software scan
2468 * is started. Can be NULL, if the driver doesn't need this notification.
2469 * The callback can sleep.
2470 *
2471 * @sw_scan_complete: Notifier function that is called just after a
2472 * software scan finished. Can be NULL, if the driver doesn't need
2473 * this notification.
2474 * The callback can sleep.
2475 *
2476 * @get_stats: Return low-level statistics.
2477 * Returns zero if statistics are available.
2478 * The callback can sleep.
2479 *
2480 * @get_tkip_seq: If your device implements TKIP encryption in hardware this
2481 * callback should be provided to read the TKIP transmit IVs (both IV32
2482 * and IV16) for the given key from hardware.
2483 * The callback must be atomic.
2484 *
2485 * @set_frag_threshold: Configuration of fragmentation threshold. Assign this
2486 * if the device does fragmentation by itself; if this callback is
2487 * implemented then the stack will not do fragmentation.
2488 * The callback can sleep.
2489 *
2490 * @set_rts_threshold: Configuration of RTS threshold (if device needs it)
2491 * The callback can sleep.
2492 *
2493 * @sta_add: Notifies low level driver about addition of an associated station,
2494 * AP, IBSS/WDS/mesh peer etc. This callback can sleep.
2495 *
2496 * @sta_remove: Notifies low level driver about removal of an associated
2497 * station, AP, IBSS/WDS/mesh peer etc. Note that after the callback
2498 * returns it isn't safe to use the pointer, not even RCU protected;
2499 * no RCU grace period is guaranteed between returning here and freeing
2500 * the station. See @sta_pre_rcu_remove if needed.
2501 * This callback can sleep.
2502 *
2503 * @sta_add_debugfs: Drivers can use this callback to add debugfs files
2504 * when a station is added to mac80211's station list. This callback
2505 * and @sta_remove_debugfs should be within a CONFIG_MAC80211_DEBUGFS
2506 * conditional. This callback can sleep.
2507 *
2508 * @sta_remove_debugfs: Remove the debugfs files which were added using
2509 * @sta_add_debugfs. This callback can sleep.
2510 *
2511 * @sta_notify: Notifies low level driver about power state transition of an
2512 * associated station, AP, IBSS/WDS/mesh peer etc. For a VIF operating
2513 * in AP mode, this callback will not be called when the flag
2514 * %IEEE80211_HW_AP_LINK_PS is set. Must be atomic.
2515 *
2516 * @sta_state: Notifies low level driver about state transition of a
2517 * station (which can be the AP, a client, IBSS/WDS/mesh peer etc.)
2518 * This callback is mutually exclusive with @sta_add/@sta_remove.
2519 * It must not fail for down transitions but may fail for transitions
2520 * up the list of states. Also note that after the callback returns it
2521 * isn't safe to use the pointer, not even RCU protected - no RCU grace
2522 * period is guaranteed between returning here and freeing the station.
2523 * See @sta_pre_rcu_remove if needed.
2524 * The callback can sleep.
2525 *
2526 * @sta_pre_rcu_remove: Notify driver about station removal before RCU
2527 * synchronisation. This is useful if a driver needs to have station
2528 * pointers protected using RCU, it can then use this call to clear
2529 * the pointers instead of waiting for an RCU grace period to elapse
2530 * in @sta_state.
2531 * The callback can sleep.
2532 *
2533 * @sta_rc_update: Notifies the driver of changes to the bitrates that can be
2534 * used to transmit to the station. The changes are advertised with bits
2535 * from &enum ieee80211_rate_control_changed and the values are reflected
2536 * in the station data. This callback should only be used when the driver
2537 * uses hardware rate control (%IEEE80211_HW_HAS_RATE_CONTROL) since
2538 * otherwise the rate control algorithm is notified directly.
2539 * Must be atomic.
2540 *
2541 * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max),
2542 * bursting) for a hardware TX queue.
2543 * Returns a negative error code on failure.
2544 * The callback can sleep.
2545 *
2546 * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
2547 * this is only used for IBSS mode BSSID merging and debugging. Is not a
2548 * required function.
2549 * The callback can sleep.
2550 *
2551 * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
2552 * Currently, this is only used for IBSS mode debugging. Is not a
2553 * required function.
2554 * The callback can sleep.
2555 *
2556 * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize
2557 * with other STAs in the IBSS. This is only used in IBSS mode. This
2558 * function is optional if the firmware/hardware takes full care of
2559 * TSF synchronization.
2560 * The callback can sleep.
2561 *
2562 * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us.
2563 * This is needed only for IBSS mode and the result of this function is
2564 * used to determine whether to reply to Probe Requests.
2565 * Returns non-zero if this device sent the last beacon.
2566 * The callback can sleep.
2567 *
2568 * @ampdu_action: Perform a certain A-MPDU action
2569 * The RA/TID combination determines the destination and TID we want
2570 * the ampdu action to be performed for. The action is defined through
2571 * ieee80211_ampdu_mlme_action. Starting sequence number (@ssn)
2572 * is the first frame we expect to perform the action on. Notice
2573 * that TX/RX_STOP can pass NULL for this parameter.
2574 * The @buf_size parameter is only valid when the action is set to
2575 * %IEEE80211_AMPDU_TX_OPERATIONAL and indicates the peer's reorder
2576 * buffer size (number of subframes) for this session -- the driver
2577 * may neither send aggregates containing more subframes than this
2578 * nor send aggregates in a way that lost frames would exceed the
2579 * buffer size. If just limiting the aggregate size, this would be
2580 * possible with a buf_size of 8:
2581 * - TX: 1.....7
2582 * - RX: 2....7 (lost frame #1)
2583 * - TX: 8..1...
2584 * which is invalid since #1 was now re-transmitted well past the
2585 * buffer size of 8. Correct ways to retransmit #1 would be:
2586 * - TX: 1 or 18 or 81
2587 * Even "189" would be wrong since 1 could be lost again.
2588 *
2589 * Returns a negative error code on failure.
2590 * The callback can sleep.
2591 *
2592 * @get_survey: Return per-channel survey information
2593 *
2594 * @rfkill_poll: Poll rfkill hardware state. If you need this, you also
2595 * need to set wiphy->rfkill_poll to %true before registration,
2596 * and need to call wiphy_rfkill_set_hw_state() in the callback.
2597 * The callback can sleep.
2598 *
2599 * @set_coverage_class: Set slot time for given coverage class as specified
2600 * in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout
2601 * accordingly. This callback is not required and may sleep.
2602 *
2603 * @testmode_cmd: Implement a cfg80211 test mode command. The passed @vif may
2604 * be %NULL. The callback can sleep.
2605 * @testmode_dump: Implement a cfg80211 test mode dump. The callback can sleep.
2606 *
2607 * @flush: Flush all pending frames from the hardware queue, making sure
2608 * that the hardware queues are empty. The @queues parameter is a bitmap
2609 * of queues to flush, which is useful if different virtual interfaces
2610 * use different hardware queues; it may also indicate all queues.
2611 * If the parameter @drop is set to %true, pending frames may be dropped.
2612 * The callback can sleep.
2613 *
2614 * @channel_switch: Drivers that need (or want) to offload the channel
2615 * switch operation for CSAs received from the AP may implement this
2616 * callback. They must then call ieee80211_chswitch_done() to indicate
2617 * completion of the channel switch.
2618 *
2619 * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device.
2620 * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may
2621 * reject TX/RX mask combinations they cannot support by returning -EINVAL
2622 * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX).
2623 *
2624 * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant).
2625 *
2626 * @remain_on_channel: Starts an off-channel period on the given channel, must
2627 * call back to ieee80211_ready_on_channel() when on that channel. Note
2628 * that normal channel traffic is not stopped as this is intended for hw
2629 * offload. Frames to transmit on the off-channel channel are transmitted
2630 * normally except for the %IEEE80211_TX_CTL_TX_OFFCHAN flag. When the
2631 * duration (which will always be non-zero) expires, the driver must call
2632 * ieee80211_remain_on_channel_expired().
2633 * Note that this callback may be called while the device is in IDLE and
2634 * must be accepted in this case.
2635 * This callback may sleep.
2636 * @cancel_remain_on_channel: Requests that an ongoing off-channel period is
2637 * aborted before it expires. This callback may sleep.
2638 *
2639 * @set_ringparam: Set tx and rx ring sizes.
2640 *
2641 * @get_ringparam: Get tx and rx ring current and maximum sizes.
2642 *
2643 * @tx_frames_pending: Check if there is any pending frame in the hardware
2644 * queues before entering power save.
2645 *
2646 * @set_bitrate_mask: Set a mask of rates to be used for rate control selection
2647 * when transmitting a frame. Currently only legacy rates are handled.
2648 * The callback can sleep.
2649 * @rssi_callback: Notify driver when the average RSSI goes above/below
2650 * thresholds that were registered previously. The callback can sleep.
2651 *
2652 * @release_buffered_frames: Release buffered frames according to the given
2653 * parameters. In the case where the driver buffers some frames for
2654 * sleeping stations mac80211 will use this callback to tell the driver
2655 * to release some frames, either for PS-poll or uAPSD.
2656 * Note that if the @more_data parameter is %false the driver must check
2657 * if there are more frames on the given TIDs, and if there are more than
2658 * the frames being released then it must still set the more-data bit in
2659 * the frame. If the @more_data parameter is %true, then of course the
2660 * more-data bit must always be set.
2661 * The @tids parameter tells the driver which TIDs to release frames
2662 * from, for PS-poll it will always have only a single bit set.
2663 * In the case this is used for a PS-poll initiated release, the
2664 * @num_frames parameter will always be 1 so code can be shared. In
2665 * this case the driver must also set %IEEE80211_TX_STATUS_EOSP flag
2666 * on the TX status (and must report TX status) so that the PS-poll
2667 * period is properly ended. This is used to avoid sending multiple
2668 * responses for a retried PS-poll frame.
2669 * In the case this is used for uAPSD, the @num_frames parameter may be
2670 * bigger than one, but the driver may send fewer frames (it must send
2671 * at least one, however). In this case it is also responsible for
2672 * setting the EOSP flag in the QoS header of the frames. Also, when the
2673 * service period ends, the driver must set %IEEE80211_TX_STATUS_EOSP
2674 * on the last frame in the SP. Alternatively, it may call the function
2675 * ieee80211_sta_eosp() to inform mac80211 of the end of the SP.
2676 * This callback must be atomic.
2677 * @allow_buffered_frames: Prepare device to allow the given number of frames
2678 * to go out to the given station. The frames will be sent by mac80211
2679 * via the usual TX path after this call. The TX information for frames
2680 * released will also have the %IEEE80211_TX_CTL_NO_PS_BUFFER flag set
2681 * and the last one will also have %IEEE80211_TX_STATUS_EOSP set. In case
2682 * frames from multiple TIDs are released and the driver might reorder
2683 * them between the TIDs, it must set the %IEEE80211_TX_STATUS_EOSP flag
2684 * on the last frame and clear it on all others and also handle the EOSP
2685 * bit in the QoS header correctly. Alternatively, it can also call the
2686 * ieee80211_sta_eosp() function.
2687 * The @tids parameter is a bitmap and tells the driver which TIDs the
2688 * frames will be on; it will at most have two bits set.
2689 * This callback must be atomic.
2690 *
2691 * @get_et_sset_count: Ethtool API to get string-set count.
2692 *
2693 * @get_et_stats: Ethtool API to get a set of u64 stats.
2694 *
2695 * @get_et_strings: Ethtool API to get a set of strings to describe stats
2696 * and perhaps other supported types of ethtool data-sets.
2697 *
2698 * @get_rssi: Get current signal strength in dBm, the function is optional
2699 * and can sleep.
2700 *
2701 * @mgd_prepare_tx: Prepare for transmitting a management frame for association
2702 * before associated. In multi-channel scenarios, a virtual interface is
2703 * bound to a channel before it is associated, but as it isn't associated
2704 * yet it need not necessarily be given airtime, in particular since any
2705 * transmission to a P2P GO needs to be synchronized against the GO's
2706 * powersave state. mac80211 will call this function before transmitting a
2707 * management frame prior to having successfully associated to allow the
2708 * driver to give it channel time for the transmission, to get a response
2709 * and to be able to synchronize with the GO.
2710 * The callback will be called before each transmission and upon return
2711 * mac80211 will transmit the frame right away.
2712 * The callback is optional and can (should!) sleep.
2713 *
2714 * @add_chanctx: Notifies device driver about new channel context creation.
2715 * @remove_chanctx: Notifies device driver about channel context destruction.
2716 * @change_chanctx: Notifies device driver about channel context changes that
2717 * may happen when combining different virtual interfaces on the same
2718 * channel context with different settings
2719 * @assign_vif_chanctx: Notifies device driver about channel context being bound
2720 * to vif. Possible use is for hw queue remapping.
2721 * @unassign_vif_chanctx: Notifies device driver about channel context being
2722 * unbound from vif.
2723 * @start_ap: Start operation on the AP interface, this is called after all the
2724 * information in bss_conf is set and beacon can be retrieved. A channel
2725 * context is bound before this is called. Note that if the driver uses
2726 * software scan or ROC, this (and @stop_ap) isn't called when the AP is
2727 * just "paused" for scanning/ROC, which is indicated by the beacon being
2728 * disabled/enabled via @bss_info_changed.
2729 * @stop_ap: Stop operation on the AP interface.
2730 *
2731 * @restart_complete: Called after a call to ieee80211_restart_hw(), when the
2732 * reconfiguration has completed. This can help the driver implement the
2733 * reconfiguration step. Also called when reconfiguring because the
2734 * driver's resume function returned 1, as this is just like an "inline"
2735 * hardware restart. This callback may sleep.
2736 *
2737 * @ipv6_addr_change: IPv6 address assignment on the given interface changed.
2738 * Currently, this is only called for managed or P2P client interfaces.
2739 * This callback is optional; it must not sleep.
2740 *
2741 * @channel_switch_beacon: Starts a channel switch to a new channel.
2742 * Beacons are modified to include CSA or ECSA IEs before calling this
2743 * function. The corresponding count fields in these IEs must be
2744 * decremented, and when they reach 1 the driver must call
2745 * ieee80211_csa_finish(). Drivers which use ieee80211_beacon_get()
2746 * get the csa counter decremented by mac80211, but must check if it is
2747 * 1 using ieee80211_csa_is_complete() after the beacon has been
2748 * transmitted and then call ieee80211_csa_finish().
2749 * If the CSA count starts as zero or 1, this function will not be called,
2750 * since there won't be any time to beacon before the switch anyway.
2751 *
2752 * @join_ibss: Join an IBSS (on an IBSS interface); this is called after all
2753 * information in bss_conf is set up and the beacon can be retrieved. A
2754 * channel context is bound before this is called.
2755 * @leave_ibss: Leave the IBSS again.
2756 */
2757struct ieee80211_ops {
2758 void (*tx)(struct ieee80211_hw *hw,
2759 struct ieee80211_tx_control *control,
2760 struct sk_buff *skb);
2761 int (*start)(struct ieee80211_hw *hw);
2762 void (*stop)(struct ieee80211_hw *hw);
2763#ifdef CONFIG_PM
2764 int (*suspend)(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan);
2765 int (*resume)(struct ieee80211_hw *hw);
2766 void (*set_wakeup)(struct ieee80211_hw *hw, bool enabled);
2767#endif
2768 int (*add_interface)(struct ieee80211_hw *hw,
2769 struct ieee80211_vif *vif);
2770 int (*change_interface)(struct ieee80211_hw *hw,
2771 struct ieee80211_vif *vif,
2772 enum nl80211_iftype new_type, bool p2p);
2773 void (*remove_interface)(struct ieee80211_hw *hw,
2774 struct ieee80211_vif *vif);
2775 int (*config)(struct ieee80211_hw *hw, u32 changed);
2776 void (*bss_info_changed)(struct ieee80211_hw *hw,
2777 struct ieee80211_vif *vif,
2778 struct ieee80211_bss_conf *info,
2779 u32 changed);
2780
2781 int (*start_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
2782 void (*stop_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
2783
2784 u64 (*prepare_multicast)(struct ieee80211_hw *hw,
2785 struct netdev_hw_addr_list *mc_list);
2786 void (*configure_filter)(struct ieee80211_hw *hw,
2787 unsigned int changed_flags,
2788 unsigned int *total_flags,
2789 u64 multicast);
2790 int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta,
2791 bool set);
2792 int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd,
2793 struct ieee80211_vif *vif, struct ieee80211_sta *sta,
2794 struct ieee80211_key_conf *key);
2795 void (*update_tkip_key)(struct ieee80211_hw *hw,
2796 struct ieee80211_vif *vif,
2797 struct ieee80211_key_conf *conf,
2798 struct ieee80211_sta *sta,
2799 u32 iv32, u16 *phase1key);
2800 void (*set_rekey_data)(struct ieee80211_hw *hw,
2801 struct ieee80211_vif *vif,
2802 struct cfg80211_gtk_rekey_data *data);
2803 void (*set_default_unicast_key)(struct ieee80211_hw *hw,
2804 struct ieee80211_vif *vif, int idx);
2805 int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
2806 struct cfg80211_scan_request *req);
2807 void (*cancel_hw_scan)(struct ieee80211_hw *hw,
2808 struct ieee80211_vif *vif);
2809 int (*sched_scan_start)(struct ieee80211_hw *hw,
2810 struct ieee80211_vif *vif,
2811 struct cfg80211_sched_scan_request *req,
2812 struct ieee80211_sched_scan_ies *ies);
2813 int (*sched_scan_stop)(struct ieee80211_hw *hw,
2814 struct ieee80211_vif *vif);
2815 void (*sw_scan_start)(struct ieee80211_hw *hw);
2816 void (*sw_scan_complete)(struct ieee80211_hw *hw);
2817 int (*get_stats)(struct ieee80211_hw *hw,
2818 struct ieee80211_low_level_stats *stats);
2819 void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx,
2820 u32 *iv32, u16 *iv16);
2821 int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);
2822 int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
2823 int (*sta_add)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
2824 struct ieee80211_sta *sta);
2825 int (*sta_remove)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
2826 struct ieee80211_sta *sta);
2827#ifdef CONFIG_MAC80211_DEBUGFS
2828 void (*sta_add_debugfs)(struct ieee80211_hw *hw,
2829 struct ieee80211_vif *vif,
2830 struct ieee80211_sta *sta,
2831 struct dentry *dir);
2832 void (*sta_remove_debugfs)(struct ieee80211_hw *hw,
2833 struct ieee80211_vif *vif,
2834 struct ieee80211_sta *sta,
2835 struct dentry *dir);
2836#endif
2837 void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
2838 enum sta_notify_cmd, struct ieee80211_sta *sta);
2839 int (*sta_state)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
2840 struct ieee80211_sta *sta,
2841 enum ieee80211_sta_state old_state,
2842 enum ieee80211_sta_state new_state);
2843 void (*sta_pre_rcu_remove)(struct ieee80211_hw *hw,
2844 struct ieee80211_vif *vif,
2845 struct ieee80211_sta *sta);
2846 void (*sta_rc_update)(struct ieee80211_hw *hw,
2847 struct ieee80211_vif *vif,
2848 struct ieee80211_sta *sta,
2849 u32 changed);
2850 int (*conf_tx)(struct ieee80211_hw *hw,
2851 struct ieee80211_vif *vif, u16 ac,
2852 const struct ieee80211_tx_queue_params *params);
2853 u64 (*get_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
2854 void (*set_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
2855 u64 tsf);
2856 void (*reset_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
2857 int (*tx_last_beacon)(struct ieee80211_hw *hw);
2858 int (*ampdu_action)(struct ieee80211_hw *hw,
2859 struct ieee80211_vif *vif,
2860 enum ieee80211_ampdu_mlme_action action,
2861 struct ieee80211_sta *sta, u16 tid, u16 *ssn,
2862 u8 buf_size);
2863 int (*get_survey)(struct ieee80211_hw *hw, int idx,
2864 struct survey_info *survey);
2865 void (*rfkill_poll)(struct ieee80211_hw *hw);
2866 void (*set_coverage_class)(struct ieee80211_hw *hw, u8 coverage_class);
2867#ifdef CONFIG_NL80211_TESTMODE
2868 int (*testmode_cmd)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
2869 void *data, int len);
2870 int (*testmode_dump)(struct ieee80211_hw *hw, struct sk_buff *skb,
2871 struct netlink_callback *cb,
2872 void *data, int len);
2873#endif
2874 void (*flush)(struct ieee80211_hw *hw, u32 queues, bool drop);
2875 void (*channel_switch)(struct ieee80211_hw *hw,
2876 struct ieee80211_channel_switch *ch_switch);
2877 int (*set_antenna)(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant);
2878 int (*get_antenna)(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant);
2879
2880 int (*remain_on_channel)(struct ieee80211_hw *hw,
2881 struct ieee80211_vif *vif,
2882 struct ieee80211_channel *chan,
2883 int duration,
2884 enum ieee80211_roc_type type);
2885 int (*cancel_remain_on_channel)(struct ieee80211_hw *hw);
2886 int (*set_ringparam)(struct ieee80211_hw *hw, u32 tx, u32 rx);
2887 void (*get_ringparam)(struct ieee80211_hw *hw,
2888 u32 *tx, u32 *tx_max, u32 *rx, u32 *rx_max);
2889 bool (*tx_frames_pending)(struct ieee80211_hw *hw);
2890 int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
2891 const struct cfg80211_bitrate_mask *mask);
2892 void (*rssi_callback)(struct ieee80211_hw *hw,
2893 struct ieee80211_vif *vif,
2894 enum ieee80211_rssi_event rssi_event);
2895
2896 void (*allow_buffered_frames)(struct ieee80211_hw *hw,
2897 struct ieee80211_sta *sta,
2898 u16 tids, int num_frames,
2899 enum ieee80211_frame_release_type reason,
2900 bool more_data);
2901 void (*release_buffered_frames)(struct ieee80211_hw *hw,
2902 struct ieee80211_sta *sta,
2903 u16 tids, int num_frames,
2904 enum ieee80211_frame_release_type reason,
2905 bool more_data);
2906
2907 int (*get_et_sset_count)(struct ieee80211_hw *hw,
2908 struct ieee80211_vif *vif, int sset);
2909 void (*get_et_stats)(struct ieee80211_hw *hw,
2910 struct ieee80211_vif *vif,
2911 struct ethtool_stats *stats, u64 *data);
2912 void (*get_et_strings)(struct ieee80211_hw *hw,
2913 struct ieee80211_vif *vif,
2914 u32 sset, u8 *data);
2915 int (*get_rssi)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
2916 struct ieee80211_sta *sta, s8 *rssi_dbm);
2917
2918 void (*mgd_prepare_tx)(struct ieee80211_hw *hw,
2919 struct ieee80211_vif *vif);
2920
2921 int (*add_chanctx)(struct ieee80211_hw *hw,
2922 struct ieee80211_chanctx_conf *ctx);
2923 void (*remove_chanctx)(struct ieee80211_hw *hw,
2924 struct ieee80211_chanctx_conf *ctx);
2925 void (*change_chanctx)(struct ieee80211_hw *hw,
2926 struct ieee80211_chanctx_conf *ctx,
2927 u32 changed);
2928 int (*assign_vif_chanctx)(struct ieee80211_hw *hw,
2929 struct ieee80211_vif *vif,
2930 struct ieee80211_chanctx_conf *ctx);
2931 void (*unassign_vif_chanctx)(struct ieee80211_hw *hw,
2932 struct ieee80211_vif *vif,
2933 struct ieee80211_chanctx_conf *ctx);
2934
2935 void (*restart_complete)(struct ieee80211_hw *hw);
2936
2937#if IS_ENABLED(CONFIG_IPV6)
2938 void (*ipv6_addr_change)(struct ieee80211_hw *hw,
2939 struct ieee80211_vif *vif,
2940 struct inet6_dev *idev);
2941#endif
2942 void (*channel_switch_beacon)(struct ieee80211_hw *hw,
2943 struct ieee80211_vif *vif,
2944 struct cfg80211_chan_def *chandef);
2945
2946 int (*join_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
2947 void (*leave_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
2948};
2949
2950/**
2951 * ieee80211_alloc_hw - Allocate a new hardware device
2952 *
2953 * This must be called once for each hardware device. The returned pointer
2954 * must be used to refer to this device when calling other functions.
2955 * mac80211 allocates a private data area for the driver pointed to by
2956 * @priv in &struct ieee80211_hw, the size of this area is given as
2957 * @priv_data_len.
2958 *
2959 * @priv_data_len: length of private data
2960 * @ops: callbacks for this device
2961 *
2962 * Return: A pointer to the new hardware device, or %NULL on error.
2963 */
2964struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len,
2965 const struct ieee80211_ops *ops);
2966
2967/**
2968 * ieee80211_register_hw - Register hardware device
2969 *
2970 * You must call this function before any other functions in
2971 * mac80211. Note that before a hardware can be registered, you
2972 * need to fill the contained wiphy's information.
2973 *
2974 * @hw: the device to register as returned by ieee80211_alloc_hw()
2975 *
2976 * Return: 0 on success. An error code otherwise.
2977 */
2978int ieee80211_register_hw(struct ieee80211_hw *hw);
2979
2980/**
2981 * struct ieee80211_tpt_blink - throughput blink description
2982 * @throughput: throughput in Kbit/sec
2983 * @blink_time: blink time in milliseconds
2984 * (full cycle, ie. one off + one on period)
2985 */
2986struct ieee80211_tpt_blink {
2987 int throughput;
2988 int blink_time;
2989};
2990
2991/**
2992 * enum ieee80211_tpt_led_trigger_flags - throughput trigger flags
2993 * @IEEE80211_TPT_LEDTRIG_FL_RADIO: enable blinking with radio
2994 * @IEEE80211_TPT_LEDTRIG_FL_WORK: enable blinking when working
2995 * @IEEE80211_TPT_LEDTRIG_FL_CONNECTED: enable blinking when at least one
2996 * interface is connected in some way, including being an AP
2997 */
2998enum ieee80211_tpt_led_trigger_flags {
2999 IEEE80211_TPT_LEDTRIG_FL_RADIO = BIT(0),
3000 IEEE80211_TPT_LEDTRIG_FL_WORK = BIT(1),
3001 IEEE80211_TPT_LEDTRIG_FL_CONNECTED = BIT(2),
3002};
3003
3004#ifdef CONFIG_MAC80211_LEDS
3005char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
3006char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
3007char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
3008char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
3009char *__ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw,
3010 unsigned int flags,
3011 const struct ieee80211_tpt_blink *blink_table,
3012 unsigned int blink_table_len);
3013#endif
3014/**
3015 * ieee80211_get_tx_led_name - get name of TX LED
3016 *
3017 * mac80211 creates a transmit LED trigger for each wireless hardware
3018 * that can be used to drive LEDs if your driver registers a LED device.
3019 * This function returns the name (or %NULL if not configured for LEDs)
3020 * of the trigger so you can automatically link the LED device.
3021 *
3022 * @hw: the hardware to get the LED trigger name for
3023 *
3024 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
3025 */
3026static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw)
3027{
3028#ifdef CONFIG_MAC80211_LEDS
3029 return __ieee80211_get_tx_led_name(hw);
3030#else
3031 return NULL;
3032#endif
3033}
3034
3035/**
3036 * ieee80211_get_rx_led_name - get name of RX LED
3037 *
3038 * mac80211 creates a receive LED trigger for each wireless hardware
3039 * that can be used to drive LEDs if your driver registers a LED device.
3040 * This function returns the name (or %NULL if not configured for LEDs)
3041 * of the trigger so you can automatically link the LED device.
3042 *
3043 * @hw: the hardware to get the LED trigger name for
3044 *
3045 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
3046 */
3047static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw)
3048{
3049#ifdef CONFIG_MAC80211_LEDS
3050 return __ieee80211_get_rx_led_name(hw);
3051#else
3052 return NULL;
3053#endif
3054}
3055
3056/**
3057 * ieee80211_get_assoc_led_name - get name of association LED
3058 *
3059 * mac80211 creates a association LED trigger for each wireless hardware
3060 * that can be used to drive LEDs if your driver registers a LED device.
3061 * This function returns the name (or %NULL if not configured for LEDs)
3062 * of the trigger so you can automatically link the LED device.
3063 *
3064 * @hw: the hardware to get the LED trigger name for
3065 *
3066 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
3067 */
3068static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw)
3069{
3070#ifdef CONFIG_MAC80211_LEDS
3071 return __ieee80211_get_assoc_led_name(hw);
3072#else
3073 return NULL;
3074#endif
3075}
3076
3077/**
3078 * ieee80211_get_radio_led_name - get name of radio LED
3079 *
3080 * mac80211 creates a radio change LED trigger for each wireless hardware
3081 * that can be used to drive LEDs if your driver registers a LED device.
3082 * This function returns the name (or %NULL if not configured for LEDs)
3083 * of the trigger so you can automatically link the LED device.
3084 *
3085 * @hw: the hardware to get the LED trigger name for
3086 *
3087 * Return: The name of the LED trigger. %NULL if not configured for LEDs.
3088 */
3089static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw)
3090{
3091#ifdef CONFIG_MAC80211_LEDS
3092 return __ieee80211_get_radio_led_name(hw);
3093#else
3094 return NULL;
3095#endif
3096}
3097
3098/**
3099 * ieee80211_create_tpt_led_trigger - create throughput LED trigger
3100 * @hw: the hardware to create the trigger for
3101 * @flags: trigger flags, see &enum ieee80211_tpt_led_trigger_flags
3102 * @blink_table: the blink table -- needs to be ordered by throughput
3103 * @blink_table_len: size of the blink table
3104 *
3105 * Return: %NULL (in case of error, or if no LED triggers are
3106 * configured) or the name of the new trigger.
3107 *
3108 * Note: This function must be called before ieee80211_register_hw().
3109 */
3110static inline char *
3111ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, unsigned int flags,
3112 const struct ieee80211_tpt_blink *blink_table,
3113 unsigned int blink_table_len)
3114{
3115#ifdef CONFIG_MAC80211_LEDS
3116 return __ieee80211_create_tpt_led_trigger(hw, flags, blink_table,
3117 blink_table_len);
3118#else
3119 return NULL;
3120#endif
3121}
3122
3123/**
3124 * ieee80211_unregister_hw - Unregister a hardware device
3125 *
3126 * This function instructs mac80211 to free allocated resources
3127 * and unregister netdevices from the networking subsystem.
3128 *
3129 * @hw: the hardware to unregister
3130 */
3131void ieee80211_unregister_hw(struct ieee80211_hw *hw);
3132
3133/**
3134 * ieee80211_free_hw - free hardware descriptor
3135 *
3136 * This function frees everything that was allocated, including the
3137 * private data for the driver. You must call ieee80211_unregister_hw()
3138 * before calling this function.
3139 *
3140 * @hw: the hardware to free
3141 */
3142void ieee80211_free_hw(struct ieee80211_hw *hw);
3143
3144/**
3145 * ieee80211_restart_hw - restart hardware completely
3146 *
3147 * Call this function when the hardware was restarted for some reason
3148 * (hardware error, ...) and the driver is unable to restore its state
3149 * by itself. mac80211 assumes that at this point the driver/hardware
3150 * is completely uninitialised and stopped, it starts the process by
3151 * calling the ->start() operation. The driver will need to reset all
3152 * internal state that it has prior to calling this function.
3153 *
3154 * @hw: the hardware to restart
3155 */
3156void ieee80211_restart_hw(struct ieee80211_hw *hw);
3157
3158/**
3159 * ieee80211_napi_add - initialize mac80211 NAPI context
3160 * @hw: the hardware to initialize the NAPI context on
3161 * @napi: the NAPI context to initialize
3162 * @napi_dev: dummy NAPI netdevice, here to not waste the space if the
3163 * driver doesn't use NAPI
3164 * @poll: poll function
3165 * @weight: default weight
3166 *
3167 * See also netif_napi_add().
3168 */
3169void ieee80211_napi_add(struct ieee80211_hw *hw, struct napi_struct *napi,
3170 struct net_device *napi_dev,
3171 int (*poll)(struct napi_struct *, int),
3172 int weight);
3173
3174/**
3175 * ieee80211_rx - receive frame
3176 *
3177 * Use this function to hand received frames to mac80211. The receive
3178 * buffer in @skb must start with an IEEE 802.11 header. In case of a
3179 * paged @skb is used, the driver is recommended to put the ieee80211
3180 * header of the frame on the linear part of the @skb to avoid memory
3181 * allocation and/or memcpy by the stack.
3182 *
3183 * This function may not be called in IRQ context. Calls to this function
3184 * for a single hardware must be synchronized against each other. Calls to
3185 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be
3186 * mixed for a single hardware. Must not run concurrently with
3187 * ieee80211_tx_status() or ieee80211_tx_status_ni().
3188 *
3189 * In process context use instead ieee80211_rx_ni().
3190 *
3191 * @hw: the hardware this frame came in on
3192 * @skb: the buffer to receive, owned by mac80211 after this call
3193 */
3194void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb);
3195
3196/**
3197 * ieee80211_rx_irqsafe - receive frame
3198 *
3199 * Like ieee80211_rx() but can be called in IRQ context
3200 * (internally defers to a tasklet.)
3201 *
3202 * Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not
3203 * be mixed for a single hardware.Must not run concurrently with
3204 * ieee80211_tx_status() or ieee80211_tx_status_ni().
3205 *
3206 * @hw: the hardware this frame came in on
3207 * @skb: the buffer to receive, owned by mac80211 after this call
3208 */
3209void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb);
3210
3211/**
3212 * ieee80211_rx_ni - receive frame (in process context)
3213 *
3214 * Like ieee80211_rx() but can be called in process context
3215 * (internally disables bottom halves).
3216 *
3217 * Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may
3218 * not be mixed for a single hardware. Must not run concurrently with
3219 * ieee80211_tx_status() or ieee80211_tx_status_ni().
3220 *
3221 * @hw: the hardware this frame came in on
3222 * @skb: the buffer to receive, owned by mac80211 after this call
3223 */
3224static inline void ieee80211_rx_ni(struct ieee80211_hw *hw,
3225 struct sk_buff *skb)
3226{
3227 local_bh_disable();
3228 ieee80211_rx(hw, skb);
3229 local_bh_enable();
3230}
3231
3232/**
3233 * ieee80211_sta_ps_transition - PS transition for connected sta
3234 *
3235 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS
3236 * flag set, use this function to inform mac80211 about a connected station
3237 * entering/leaving PS mode.
3238 *
3239 * This function may not be called in IRQ context or with softirqs enabled.
3240 *
3241 * Calls to this function for a single hardware must be synchronized against
3242 * each other.
3243 *
3244 * @sta: currently connected sta
3245 * @start: start or stop PS
3246 *
3247 * Return: 0 on success. -EINVAL when the requested PS mode is already set.
3248 */
3249int ieee80211_sta_ps_transition(struct ieee80211_sta *sta, bool start);
3250
3251/**
3252 * ieee80211_sta_ps_transition_ni - PS transition for connected sta
3253 * (in process context)
3254 *
3255 * Like ieee80211_sta_ps_transition() but can be called in process context
3256 * (internally disables bottom halves). Concurrent call restriction still
3257 * applies.
3258 *
3259 * @sta: currently connected sta
3260 * @start: start or stop PS
3261 *
3262 * Return: Like ieee80211_sta_ps_transition().
3263 */
3264static inline int ieee80211_sta_ps_transition_ni(struct ieee80211_sta *sta,
3265 bool start)
3266{
3267 int ret;
3268
3269 local_bh_disable();
3270 ret = ieee80211_sta_ps_transition(sta, start);
3271 local_bh_enable();
3272
3273 return ret;
3274}
3275
3276/*
3277 * The TX headroom reserved by mac80211 for its own tx_status functions.
3278 * This is enough for the radiotap header.
3279 */
3280#define IEEE80211_TX_STATUS_HEADROOM 14
3281
3282/**
3283 * ieee80211_sta_set_buffered - inform mac80211 about driver-buffered frames
3284 * @sta: &struct ieee80211_sta pointer for the sleeping station
3285 * @tid: the TID that has buffered frames
3286 * @buffered: indicates whether or not frames are buffered for this TID
3287 *
3288 * If a driver buffers frames for a powersave station instead of passing
3289 * them back to mac80211 for retransmission, the station may still need
3290 * to be told that there are buffered frames via the TIM bit.
3291 *
3292 * This function informs mac80211 whether or not there are frames that are
3293 * buffered in the driver for a given TID; mac80211 can then use this data
3294 * to set the TIM bit (NOTE: This may call back into the driver's set_tim
3295 * call! Beware of the locking!)
3296 *
3297 * If all frames are released to the station (due to PS-poll or uAPSD)
3298 * then the driver needs to inform mac80211 that there no longer are
3299 * frames buffered. However, when the station wakes up mac80211 assumes
3300 * that all buffered frames will be transmitted and clears this data,
3301 * drivers need to make sure they inform mac80211 about all buffered
3302 * frames on the sleep transition (sta_notify() with %STA_NOTIFY_SLEEP).
3303 *
3304 * Note that technically mac80211 only needs to know this per AC, not per
3305 * TID, but since driver buffering will inevitably happen per TID (since
3306 * it is related to aggregation) it is easier to make mac80211 map the
3307 * TID to the AC as required instead of keeping track in all drivers that
3308 * use this API.
3309 */
3310void ieee80211_sta_set_buffered(struct ieee80211_sta *sta,
3311 u8 tid, bool buffered);
3312
3313/**
3314 * ieee80211_get_tx_rates - get the selected transmit rates for a packet
3315 *
3316 * Call this function in a driver with per-packet rate selection support
3317 * to combine the rate info in the packet tx info with the most recent
3318 * rate selection table for the station entry.
3319 *
3320 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3321 * @sta: the receiver station to which this packet is sent.
3322 * @skb: the frame to be transmitted.
3323 * @dest: buffer for extracted rate/retry information
3324 * @max_rates: maximum number of rates to fetch
3325 */
3326void ieee80211_get_tx_rates(struct ieee80211_vif *vif,
3327 struct ieee80211_sta *sta,
3328 struct sk_buff *skb,
3329 struct ieee80211_tx_rate *dest,
3330 int max_rates);
3331
3332/**
3333 * ieee80211_tx_status - transmit status callback
3334 *
3335 * Call this function for all transmitted frames after they have been
3336 * transmitted. It is permissible to not call this function for
3337 * multicast frames but this can affect statistics.
3338 *
3339 * This function may not be called in IRQ context. Calls to this function
3340 * for a single hardware must be synchronized against each other. Calls
3341 * to this function, ieee80211_tx_status_ni() and ieee80211_tx_status_irqsafe()
3342 * may not be mixed for a single hardware. Must not run concurrently with
3343 * ieee80211_rx() or ieee80211_rx_ni().
3344 *
3345 * @hw: the hardware the frame was transmitted by
3346 * @skb: the frame that was transmitted, owned by mac80211 after this call
3347 */
3348void ieee80211_tx_status(struct ieee80211_hw *hw,
3349 struct sk_buff *skb);
3350
3351/**
3352 * ieee80211_tx_status_ni - transmit status callback (in process context)
3353 *
3354 * Like ieee80211_tx_status() but can be called in process context.
3355 *
3356 * Calls to this function, ieee80211_tx_status() and
3357 * ieee80211_tx_status_irqsafe() may not be mixed
3358 * for a single hardware.
3359 *
3360 * @hw: the hardware the frame was transmitted by
3361 * @skb: the frame that was transmitted, owned by mac80211 after this call
3362 */
3363static inline void ieee80211_tx_status_ni(struct ieee80211_hw *hw,
3364 struct sk_buff *skb)
3365{
3366 local_bh_disable();
3367 ieee80211_tx_status(hw, skb);
3368 local_bh_enable();
3369}
3370
3371/**
3372 * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback
3373 *
3374 * Like ieee80211_tx_status() but can be called in IRQ context
3375 * (internally defers to a tasklet.)
3376 *
3377 * Calls to this function, ieee80211_tx_status() and
3378 * ieee80211_tx_status_ni() may not be mixed for a single hardware.
3379 *
3380 * @hw: the hardware the frame was transmitted by
3381 * @skb: the frame that was transmitted, owned by mac80211 after this call
3382 */
3383void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
3384 struct sk_buff *skb);
3385
3386/**
3387 * ieee80211_report_low_ack - report non-responding station
3388 *
3389 * When operating in AP-mode, call this function to report a non-responding
3390 * connected STA.
3391 *
3392 * @sta: the non-responding connected sta
3393 * @num_packets: number of packets sent to @sta without a response
3394 */
3395void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets);
3396
3397/**
3398 * ieee80211_beacon_get_tim - beacon generation function
3399 * @hw: pointer obtained from ieee80211_alloc_hw().
3400 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3401 * @tim_offset: pointer to variable that will receive the TIM IE offset.
3402 * Set to 0 if invalid (in non-AP modes).
3403 * @tim_length: pointer to variable that will receive the TIM IE length,
3404 * (including the ID and length bytes!).
3405 * Set to 0 if invalid (in non-AP modes).
3406 *
3407 * If the driver implements beaconing modes, it must use this function to
3408 * obtain the beacon frame/template.
3409 *
3410 * If the beacon frames are generated by the host system (i.e., not in
3411 * hardware/firmware), the driver uses this function to get each beacon
3412 * frame from mac80211 -- it is responsible for calling this function
3413 * before the beacon is needed (e.g. based on hardware interrupt).
3414 *
3415 * If the beacon frames are generated by the device, then the driver
3416 * must use the returned beacon as the template and change the TIM IE
3417 * according to the current DTIM parameters/TIM bitmap.
3418 *
3419 * The driver is responsible for freeing the returned skb.
3420 *
3421 * Return: The beacon template. %NULL on error.
3422 */
3423struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw,
3424 struct ieee80211_vif *vif,
3425 u16 *tim_offset, u16 *tim_length);
3426
3427/**
3428 * ieee80211_beacon_get - beacon generation function
3429 * @hw: pointer obtained from ieee80211_alloc_hw().
3430 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3431 *
3432 * See ieee80211_beacon_get_tim().
3433 *
3434 * Return: See ieee80211_beacon_get_tim().
3435 */
3436static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
3437 struct ieee80211_vif *vif)
3438{
3439 return ieee80211_beacon_get_tim(hw, vif, NULL, NULL);
3440}
3441
3442/**
3443 * ieee80211_csa_finish - notify mac80211 about channel switch
3444 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3445 *
3446 * After a channel switch announcement was scheduled and the counter in this
3447 * announcement hits 1, this function must be called by the driver to
3448 * notify mac80211 that the channel can be changed.
3449 */
3450void ieee80211_csa_finish(struct ieee80211_vif *vif);
3451
3452/**
3453 * ieee80211_csa_is_complete - find out if counters reached 1
3454 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3455 *
3456 * This function returns whether the channel switch counters reached zero.
3457 */
3458bool ieee80211_csa_is_complete(struct ieee80211_vif *vif);
3459
3460
3461/**
3462 * ieee80211_proberesp_get - retrieve a Probe Response template
3463 * @hw: pointer obtained from ieee80211_alloc_hw().
3464 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3465 *
3466 * Creates a Probe Response template which can, for example, be uploaded to
3467 * hardware. The destination address should be set by the caller.
3468 *
3469 * Can only be called in AP mode.
3470 *
3471 * Return: The Probe Response template. %NULL on error.
3472 */
3473struct sk_buff *ieee80211_proberesp_get(struct ieee80211_hw *hw,
3474 struct ieee80211_vif *vif);
3475
3476/**
3477 * ieee80211_pspoll_get - retrieve a PS Poll template
3478 * @hw: pointer obtained from ieee80211_alloc_hw().
3479 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3480 *
3481 * Creates a PS Poll a template which can, for example, uploaded to
3482 * hardware. The template must be updated after association so that correct
3483 * AID, BSSID and MAC address is used.
3484 *
3485 * Note: Caller (or hardware) is responsible for setting the
3486 * &IEEE80211_FCTL_PM bit.
3487 *
3488 * Return: The PS Poll template. %NULL on error.
3489 */
3490struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw,
3491 struct ieee80211_vif *vif);
3492
3493/**
3494 * ieee80211_nullfunc_get - retrieve a nullfunc template
3495 * @hw: pointer obtained from ieee80211_alloc_hw().
3496 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3497 *
3498 * Creates a Nullfunc template which can, for example, uploaded to
3499 * hardware. The template must be updated after association so that correct
3500 * BSSID and address is used.
3501 *
3502 * Note: Caller (or hardware) is responsible for setting the
3503 * &IEEE80211_FCTL_PM bit as well as Duration and Sequence Control fields.
3504 *
3505 * Return: The nullfunc template. %NULL on error.
3506 */
3507struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw,
3508 struct ieee80211_vif *vif);
3509
3510/**
3511 * ieee80211_probereq_get - retrieve a Probe Request template
3512 * @hw: pointer obtained from ieee80211_alloc_hw().
3513 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3514 * @ssid: SSID buffer
3515 * @ssid_len: length of SSID
3516 * @tailroom: tailroom to reserve at end of SKB for IEs
3517 *
3518 * Creates a Probe Request template which can, for example, be uploaded to
3519 * hardware.
3520 *
3521 * Return: The Probe Request template. %NULL on error.
3522 */
3523struct sk_buff *ieee80211_probereq_get(struct ieee80211_hw *hw,
3524 struct ieee80211_vif *vif,
3525 const u8 *ssid, size_t ssid_len,
3526 size_t tailroom);
3527
3528/**
3529 * ieee80211_rts_get - RTS frame generation function
3530 * @hw: pointer obtained from ieee80211_alloc_hw().
3531 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3532 * @frame: pointer to the frame that is going to be protected by the RTS.
3533 * @frame_len: the frame length (in octets).
3534 * @frame_txctl: &struct ieee80211_tx_info of the frame.
3535 * @rts: The buffer where to store the RTS frame.
3536 *
3537 * If the RTS frames are generated by the host system (i.e., not in
3538 * hardware/firmware), the low-level driver uses this function to receive
3539 * the next RTS frame from the 802.11 code. The low-level is responsible
3540 * for calling this function before and RTS frame is needed.
3541 */
3542void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
3543 const void *frame, size_t frame_len,
3544 const struct ieee80211_tx_info *frame_txctl,
3545 struct ieee80211_rts *rts);
3546
3547/**
3548 * ieee80211_rts_duration - Get the duration field for an RTS frame
3549 * @hw: pointer obtained from ieee80211_alloc_hw().
3550 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3551 * @frame_len: the length of the frame that is going to be protected by the RTS.
3552 * @frame_txctl: &struct ieee80211_tx_info of the frame.
3553 *
3554 * If the RTS is generated in firmware, but the host system must provide
3555 * the duration field, the low-level driver uses this function to receive
3556 * the duration field value in little-endian byteorder.
3557 *
3558 * Return: The duration.
3559 */
3560__le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
3561 struct ieee80211_vif *vif, size_t frame_len,
3562 const struct ieee80211_tx_info *frame_txctl);
3563
3564/**
3565 * ieee80211_ctstoself_get - CTS-to-self frame generation function
3566 * @hw: pointer obtained from ieee80211_alloc_hw().
3567 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3568 * @frame: pointer to the frame that is going to be protected by the CTS-to-self.
3569 * @frame_len: the frame length (in octets).
3570 * @frame_txctl: &struct ieee80211_tx_info of the frame.
3571 * @cts: The buffer where to store the CTS-to-self frame.
3572 *
3573 * If the CTS-to-self frames are generated by the host system (i.e., not in
3574 * hardware/firmware), the low-level driver uses this function to receive
3575 * the next CTS-to-self frame from the 802.11 code. The low-level is responsible
3576 * for calling this function before and CTS-to-self frame is needed.
3577 */
3578void ieee80211_ctstoself_get(struct ieee80211_hw *hw,
3579 struct ieee80211_vif *vif,
3580 const void *frame, size_t frame_len,
3581 const struct ieee80211_tx_info *frame_txctl,
3582 struct ieee80211_cts *cts);
3583
3584/**
3585 * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame
3586 * @hw: pointer obtained from ieee80211_alloc_hw().
3587 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3588 * @frame_len: the length of the frame that is going to be protected by the CTS-to-self.
3589 * @frame_txctl: &struct ieee80211_tx_info of the frame.
3590 *
3591 * If the CTS-to-self is generated in firmware, but the host system must provide
3592 * the duration field, the low-level driver uses this function to receive
3593 * the duration field value in little-endian byteorder.
3594 *
3595 * Return: The duration.
3596 */
3597__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
3598 struct ieee80211_vif *vif,
3599 size_t frame_len,
3600 const struct ieee80211_tx_info *frame_txctl);
3601
3602/**
3603 * ieee80211_generic_frame_duration - Calculate the duration field for a frame
3604 * @hw: pointer obtained from ieee80211_alloc_hw().
3605 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3606 * @band: the band to calculate the frame duration on
3607 * @frame_len: the length of the frame.
3608 * @rate: the rate at which the frame is going to be transmitted.
3609 *
3610 * Calculate the duration field of some generic frame, given its
3611 * length and transmission rate (in 100kbps).
3612 *
3613 * Return: The duration.
3614 */
3615__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
3616 struct ieee80211_vif *vif,
3617 enum ieee80211_band band,
3618 size_t frame_len,
3619 struct ieee80211_rate *rate);
3620
3621/**
3622 * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames
3623 * @hw: pointer as obtained from ieee80211_alloc_hw().
3624 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
3625 *
3626 * Function for accessing buffered broadcast and multicast frames. If
3627 * hardware/firmware does not implement buffering of broadcast/multicast
3628 * frames when power saving is used, 802.11 code buffers them in the host
3629 * memory. The low-level driver uses this function to fetch next buffered
3630 * frame. In most cases, this is used when generating beacon frame.
3631 *
3632 * Return: A pointer to the next buffered skb or NULL if no more buffered
3633 * frames are available.
3634 *
3635 * Note: buffered frames are returned only after DTIM beacon frame was
3636 * generated with ieee80211_beacon_get() and the low-level driver must thus
3637 * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns
3638 * NULL if the previous generated beacon was not DTIM, so the low-level driver
3639 * does not need to check for DTIM beacons separately and should be able to
3640 * use common code for all beacons.
3641 */
3642struct sk_buff *
3643ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif);
3644
3645/**
3646 * ieee80211_get_tkip_p1k_iv - get a TKIP phase 1 key for IV32
3647 *
3648 * This function returns the TKIP phase 1 key for the given IV32.
3649 *
3650 * @keyconf: the parameter passed with the set key
3651 * @iv32: IV32 to get the P1K for
3652 * @p1k: a buffer to which the key will be written, as 5 u16 values
3653 */
3654void ieee80211_get_tkip_p1k_iv(struct ieee80211_key_conf *keyconf,
3655 u32 iv32, u16 *p1k);
3656
3657/**
3658 * ieee80211_get_tkip_p1k - get a TKIP phase 1 key
3659 *
3660 * This function returns the TKIP phase 1 key for the IV32 taken
3661 * from the given packet.
3662 *
3663 * @keyconf: the parameter passed with the set key
3664 * @skb: the packet to take the IV32 value from that will be encrypted
3665 * with this P1K
3666 * @p1k: a buffer to which the key will be written, as 5 u16 values
3667 */
3668static inline void ieee80211_get_tkip_p1k(struct ieee80211_key_conf *keyconf,
3669 struct sk_buff *skb, u16 *p1k)
3670{
3671 struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
3672 const u8 *data = (u8 *)hdr + ieee80211_hdrlen(hdr->frame_control);
3673 u32 iv32 = get_unaligned_le32(&data[4]);
3674
3675 ieee80211_get_tkip_p1k_iv(keyconf, iv32, p1k);
3676}
3677
3678/**
3679 * ieee80211_get_tkip_rx_p1k - get a TKIP phase 1 key for RX
3680 *
3681 * This function returns the TKIP phase 1 key for the given IV32
3682 * and transmitter address.
3683 *
3684 * @keyconf: the parameter passed with the set key
3685 * @ta: TA that will be used with the key
3686 * @iv32: IV32 to get the P1K for
3687 * @p1k: a buffer to which the key will be written, as 5 u16 values
3688 */
3689void ieee80211_get_tkip_rx_p1k(struct ieee80211_key_conf *keyconf,
3690 const u8 *ta, u32 iv32, u16 *p1k);
3691
3692/**
3693 * ieee80211_get_tkip_p2k - get a TKIP phase 2 key
3694 *
3695 * This function computes the TKIP RC4 key for the IV values
3696 * in the packet.
3697 *
3698 * @keyconf: the parameter passed with the set key
3699 * @skb: the packet to take the IV32/IV16 values from that will be
3700 * encrypted with this key
3701 * @p2k: a buffer to which the key will be written, 16 bytes
3702 */
3703void ieee80211_get_tkip_p2k(struct ieee80211_key_conf *keyconf,
3704 struct sk_buff *skb, u8 *p2k);
3705
3706/**
3707 * ieee80211_aes_cmac_calculate_k1_k2 - calculate the AES-CMAC sub keys
3708 *
3709 * This function computes the two AES-CMAC sub-keys, based on the
3710 * previously installed master key.
3711 *
3712 * @keyconf: the parameter passed with the set key
3713 * @k1: a buffer to be filled with the 1st sub-key
3714 * @k2: a buffer to be filled with the 2nd sub-key
3715 */
3716void ieee80211_aes_cmac_calculate_k1_k2(struct ieee80211_key_conf *keyconf,
3717 u8 *k1, u8 *k2);
3718
3719/**
3720 * struct ieee80211_key_seq - key sequence counter
3721 *
3722 * @tkip: TKIP data, containing IV32 and IV16 in host byte order
3723 * @ccmp: PN data, most significant byte first (big endian,
3724 * reverse order than in packet)
3725 * @aes_cmac: PN data, most significant byte first (big endian,
3726 * reverse order than in packet)
3727 */
3728struct ieee80211_key_seq {
3729 union {
3730 struct {
3731 u32 iv32;
3732 u16 iv16;
3733 } tkip;
3734 struct {
3735 u8 pn[6];
3736 } ccmp;
3737 struct {
3738 u8 pn[6];
3739 } aes_cmac;
3740 };
3741};
3742
3743/**
3744 * ieee80211_get_key_tx_seq - get key TX sequence counter
3745 *
3746 * @keyconf: the parameter passed with the set key
3747 * @seq: buffer to receive the sequence data
3748 *
3749 * This function allows a driver to retrieve the current TX IV/PN
3750 * for the given key. It must not be called if IV generation is
3751 * offloaded to the device.
3752 *
3753 * Note that this function may only be called when no TX processing
3754 * can be done concurrently, for example when queues are stopped
3755 * and the stop has been synchronized.
3756 */
3757void ieee80211_get_key_tx_seq(struct ieee80211_key_conf *keyconf,
3758 struct ieee80211_key_seq *seq);
3759
3760/**
3761 * ieee80211_get_key_rx_seq - get key RX sequence counter
3762 *
3763 * @keyconf: the parameter passed with the set key
3764 * @tid: The TID, or -1 for the management frame value (CCMP only);
3765 * the value on TID 0 is also used for non-QoS frames. For
3766 * CMAC, only TID 0 is valid.
3767 * @seq: buffer to receive the sequence data
3768 *
3769 * This function allows a driver to retrieve the current RX IV/PNs
3770 * for the given key. It must not be called if IV checking is done
3771 * by the device and not by mac80211.
3772 *
3773 * Note that this function may only be called when no RX processing
3774 * can be done concurrently.
3775 */
3776void ieee80211_get_key_rx_seq(struct ieee80211_key_conf *keyconf,
3777 int tid, struct ieee80211_key_seq *seq);
3778
3779/**
3780 * ieee80211_set_key_tx_seq - set key TX sequence counter
3781 *
3782 * @keyconf: the parameter passed with the set key
3783 * @seq: new sequence data
3784 *
3785 * This function allows a driver to set the current TX IV/PNs for the
3786 * given key. This is useful when resuming from WoWLAN sleep and the
3787 * device may have transmitted frames using the PTK, e.g. replies to
3788 * ARP requests.
3789 *
3790 * Note that this function may only be called when no TX processing
3791 * can be done concurrently.
3792 */
3793void ieee80211_set_key_tx_seq(struct ieee80211_key_conf *keyconf,
3794 struct ieee80211_key_seq *seq);
3795
3796/**
3797 * ieee80211_set_key_rx_seq - set key RX sequence counter
3798 *
3799 * @keyconf: the parameter passed with the set key
3800 * @tid: The TID, or -1 for the management frame value (CCMP only);
3801 * the value on TID 0 is also used for non-QoS frames. For
3802 * CMAC, only TID 0 is valid.
3803 * @seq: new sequence data
3804 *
3805 * This function allows a driver to set the current RX IV/PNs for the
3806 * given key. This is useful when resuming from WoWLAN sleep and GTK
3807 * rekey may have been done while suspended. It should not be called
3808 * if IV checking is done by the device and not by mac80211.
3809 *
3810 * Note that this function may only be called when no RX processing
3811 * can be done concurrently.
3812 */
3813void ieee80211_set_key_rx_seq(struct ieee80211_key_conf *keyconf,
3814 int tid, struct ieee80211_key_seq *seq);
3815
3816/**
3817 * ieee80211_remove_key - remove the given key
3818 * @keyconf: the parameter passed with the set key
3819 *
3820 * Remove the given key. If the key was uploaded to the hardware at the
3821 * time this function is called, it is not deleted in the hardware but
3822 * instead assumed to have been removed already.
3823 *
3824 * Note that due to locking considerations this function can (currently)
3825 * only be called during key iteration (ieee80211_iter_keys().)
3826 */
3827void ieee80211_remove_key(struct ieee80211_key_conf *keyconf);
3828
3829/**
3830 * ieee80211_gtk_rekey_add - add a GTK key from rekeying during WoWLAN
3831 * @vif: the virtual interface to add the key on
3832 * @keyconf: new key data
3833 *
3834 * When GTK rekeying was done while the system was suspended, (a) new
3835 * key(s) will be available. These will be needed by mac80211 for proper
3836 * RX processing, so this function allows setting them.
3837 *
3838 * The function returns the newly allocated key structure, which will
3839 * have similar contents to the passed key configuration but point to
3840 * mac80211-owned memory. In case of errors, the function returns an
3841 * ERR_PTR(), use IS_ERR() etc.
3842 *
3843 * Note that this function assumes the key isn't added to hardware
3844 * acceleration, so no TX will be done with the key. Since it's a GTK
3845 * on managed (station) networks, this is true anyway. If the driver
3846 * calls this function from the resume callback and subsequently uses
3847 * the return code 1 to reconfigure the device, this key will be part
3848 * of the reconfiguration.
3849 *
3850 * Note that the driver should also call ieee80211_set_key_rx_seq()
3851 * for the new key for each TID to set up sequence counters properly.
3852 *
3853 * IMPORTANT: If this replaces a key that is present in the hardware,
3854 * then it will attempt to remove it during this call. In many cases
3855 * this isn't what you want, so call ieee80211_remove_key() first for
3856 * the key that's being replaced.
3857 */
3858struct ieee80211_key_conf *
3859ieee80211_gtk_rekey_add(struct ieee80211_vif *vif,
3860 struct ieee80211_key_conf *keyconf);
3861
3862/**
3863 * ieee80211_gtk_rekey_notify - notify userspace supplicant of rekeying
3864 * @vif: virtual interface the rekeying was done on
3865 * @bssid: The BSSID of the AP, for checking association
3866 * @replay_ctr: the new replay counter after GTK rekeying
3867 * @gfp: allocation flags
3868 */
3869void ieee80211_gtk_rekey_notify(struct ieee80211_vif *vif, const u8 *bssid,
3870 const u8 *replay_ctr, gfp_t gfp);
3871
3872/**
3873 * ieee80211_wake_queue - wake specific queue
3874 * @hw: pointer as obtained from ieee80211_alloc_hw().
3875 * @queue: queue number (counted from zero).
3876 *
3877 * Drivers should use this function instead of netif_wake_queue.
3878 */
3879void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue);
3880
3881/**
3882 * ieee80211_stop_queue - stop specific queue
3883 * @hw: pointer as obtained from ieee80211_alloc_hw().
3884 * @queue: queue number (counted from zero).
3885 *
3886 * Drivers should use this function instead of netif_stop_queue.
3887 */
3888void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue);
3889
3890/**
3891 * ieee80211_queue_stopped - test status of the queue
3892 * @hw: pointer as obtained from ieee80211_alloc_hw().
3893 * @queue: queue number (counted from zero).
3894 *
3895 * Drivers should use this function instead of netif_stop_queue.
3896 *
3897 * Return: %true if the queue is stopped. %false otherwise.
3898 */
3899
3900int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue);
3901
3902/**
3903 * ieee80211_stop_queues - stop all queues
3904 * @hw: pointer as obtained from ieee80211_alloc_hw().
3905 *
3906 * Drivers should use this function instead of netif_stop_queue.
3907 */
3908void ieee80211_stop_queues(struct ieee80211_hw *hw);
3909
3910/**
3911 * ieee80211_wake_queues - wake all queues
3912 * @hw: pointer as obtained from ieee80211_alloc_hw().
3913 *
3914 * Drivers should use this function instead of netif_wake_queue.
3915 */
3916void ieee80211_wake_queues(struct ieee80211_hw *hw);
3917
3918/**
3919 * ieee80211_scan_completed - completed hardware scan
3920 *
3921 * When hardware scan offload is used (i.e. the hw_scan() callback is
3922 * assigned) this function needs to be called by the driver to notify
3923 * mac80211 that the scan finished. This function can be called from
3924 * any context, including hardirq context.
3925 *
3926 * @hw: the hardware that finished the scan
3927 * @aborted: set to true if scan was aborted
3928 */
3929void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted);
3930
3931/**
3932 * ieee80211_sched_scan_results - got results from scheduled scan
3933 *
3934 * When a scheduled scan is running, this function needs to be called by the
3935 * driver whenever there are new scan results available.
3936 *
3937 * @hw: the hardware that is performing scheduled scans
3938 */
3939void ieee80211_sched_scan_results(struct ieee80211_hw *hw);
3940
3941/**
3942 * ieee80211_sched_scan_stopped - inform that the scheduled scan has stopped
3943 *
3944 * When a scheduled scan is running, this function can be called by
3945 * the driver if it needs to stop the scan to perform another task.
3946 * Usual scenarios are drivers that cannot continue the scheduled scan
3947 * while associating, for instance.
3948 *
3949 * @hw: the hardware that is performing scheduled scans
3950 */
3951void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw);
3952
3953/**
3954 * enum ieee80211_interface_iteration_flags - interface iteration flags
3955 * @IEEE80211_IFACE_ITER_NORMAL: Iterate over all interfaces that have
3956 * been added to the driver; However, note that during hardware
3957 * reconfiguration (after restart_hw) it will iterate over a new
3958 * interface and over all the existing interfaces even if they
3959 * haven't been re-added to the driver yet.
3960 * @IEEE80211_IFACE_ITER_RESUME_ALL: During resume, iterate over all
3961 * interfaces, even if they haven't been re-added to the driver yet.
3962 */
3963enum ieee80211_interface_iteration_flags {
3964 IEEE80211_IFACE_ITER_NORMAL = 0,
3965 IEEE80211_IFACE_ITER_RESUME_ALL = BIT(0),
3966};
3967
3968/**
3969 * ieee80211_iterate_active_interfaces - iterate active interfaces
3970 *
3971 * This function iterates over the interfaces associated with a given
3972 * hardware that are currently active and calls the callback for them.
3973 * This function allows the iterator function to sleep, when the iterator
3974 * function is atomic @ieee80211_iterate_active_interfaces_atomic can
3975 * be used.
3976 * Does not iterate over a new interface during add_interface().
3977 *
3978 * @hw: the hardware struct of which the interfaces should be iterated over
3979 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
3980 * @iterator: the iterator function to call
3981 * @data: first argument of the iterator function
3982 */
3983void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw,
3984 u32 iter_flags,
3985 void (*iterator)(void *data, u8 *mac,
3986 struct ieee80211_vif *vif),
3987 void *data);
3988
3989/**
3990 * ieee80211_iterate_active_interfaces_atomic - iterate active interfaces
3991 *
3992 * This function iterates over the interfaces associated with a given
3993 * hardware that are currently active and calls the callback for them.
3994 * This function requires the iterator callback function to be atomic,
3995 * if that is not desired, use @ieee80211_iterate_active_interfaces instead.
3996 * Does not iterate over a new interface during add_interface().
3997 *
3998 * @hw: the hardware struct of which the interfaces should be iterated over
3999 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
4000 * @iterator: the iterator function to call, cannot sleep
4001 * @data: first argument of the iterator function
4002 */
4003void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw,
4004 u32 iter_flags,
4005 void (*iterator)(void *data,
4006 u8 *mac,
4007 struct ieee80211_vif *vif),
4008 void *data);
4009
4010/**
4011 * ieee80211_iterate_active_interfaces_rtnl - iterate active interfaces
4012 *
4013 * This function iterates over the interfaces associated with a given
4014 * hardware that are currently active and calls the callback for them.
4015 * This version can only be used while holding the RTNL.
4016 *
4017 * @hw: the hardware struct of which the interfaces should be iterated over
4018 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags
4019 * @iterator: the iterator function to call, cannot sleep
4020 * @data: first argument of the iterator function
4021 */
4022void ieee80211_iterate_active_interfaces_rtnl(struct ieee80211_hw *hw,
4023 u32 iter_flags,
4024 void (*iterator)(void *data,
4025 u8 *mac,
4026 struct ieee80211_vif *vif),
4027 void *data);
4028
4029/**
4030 * ieee80211_queue_work - add work onto the mac80211 workqueue
4031 *
4032 * Drivers and mac80211 use this to add work onto the mac80211 workqueue.
4033 * This helper ensures drivers are not queueing work when they should not be.
4034 *
4035 * @hw: the hardware struct for the interface we are adding work for
4036 * @work: the work we want to add onto the mac80211 workqueue
4037 */
4038void ieee80211_queue_work(struct ieee80211_hw *hw, struct work_struct *work);
4039
4040/**
4041 * ieee80211_queue_delayed_work - add work onto the mac80211 workqueue
4042 *
4043 * Drivers and mac80211 use this to queue delayed work onto the mac80211
4044 * workqueue.
4045 *
4046 * @hw: the hardware struct for the interface we are adding work for
4047 * @dwork: delayable work to queue onto the mac80211 workqueue
4048 * @delay: number of jiffies to wait before queueing
4049 */
4050void ieee80211_queue_delayed_work(struct ieee80211_hw *hw,
4051 struct delayed_work *dwork,
4052 unsigned long delay);
4053
4054/**
4055 * ieee80211_start_tx_ba_session - Start a tx Block Ack session.
4056 * @sta: the station for which to start a BA session
4057 * @tid: the TID to BA on.
4058 * @timeout: session timeout value (in TUs)
4059 *
4060 * Return: success if addBA request was sent, failure otherwise
4061 *
4062 * Although mac80211/low level driver/user space application can estimate
4063 * the need to start aggregation on a certain RA/TID, the session level
4064 * will be managed by the mac80211.
4065 */
4066int ieee80211_start_tx_ba_session(struct ieee80211_sta *sta, u16 tid,
4067 u16 timeout);
4068
4069/**
4070 * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate.
4071 * @vif: &struct ieee80211_vif pointer from the add_interface callback
4072 * @ra: receiver address of the BA session recipient.
4073 * @tid: the TID to BA on.
4074 *
4075 * This function must be called by low level driver once it has
4076 * finished with preparations for the BA session. It can be called
4077 * from any context.
4078 */
4079void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
4080 u16 tid);
4081
4082/**
4083 * ieee80211_stop_tx_ba_session - Stop a Block Ack session.
4084 * @sta: the station whose BA session to stop
4085 * @tid: the TID to stop BA.
4086 *
4087 * Return: negative error if the TID is invalid, or no aggregation active
4088 *
4089 * Although mac80211/low level driver/user space application can estimate
4090 * the need to stop aggregation on a certain RA/TID, the session level
4091 * will be managed by the mac80211.
4092 */
4093int ieee80211_stop_tx_ba_session(struct ieee80211_sta *sta, u16 tid);
4094
4095/**
4096 * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate.
4097 * @vif: &struct ieee80211_vif pointer from the add_interface callback
4098 * @ra: receiver address of the BA session recipient.
4099 * @tid: the desired TID to BA on.
4100 *
4101 * This function must be called by low level driver once it has
4102 * finished with preparations for the BA session tear down. It
4103 * can be called from any context.
4104 */
4105void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra,
4106 u16 tid);
4107
4108/**
4109 * ieee80211_find_sta - find a station
4110 *
4111 * @vif: virtual interface to look for station on
4112 * @addr: station's address
4113 *
4114 * Return: The station, if found. %NULL otherwise.
4115 *
4116 * Note: This function must be called under RCU lock and the
4117 * resulting pointer is only valid under RCU lock as well.
4118 */
4119struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif,
4120 const u8 *addr);
4121
4122/**
4123 * ieee80211_find_sta_by_ifaddr - find a station on hardware
4124 *
4125 * @hw: pointer as obtained from ieee80211_alloc_hw()
4126 * @addr: remote station's address
4127 * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'.
4128 *
4129 * Return: The station, if found. %NULL otherwise.
4130 *
4131 * Note: This function must be called under RCU lock and the
4132 * resulting pointer is only valid under RCU lock as well.
4133 *
4134 * NOTE: You may pass NULL for localaddr, but then you will just get
4135 * the first STA that matches the remote address 'addr'.
4136 * We can have multiple STA associated with multiple
4137 * logical stations (e.g. consider a station connecting to another
4138 * BSSID on the same AP hardware without disconnecting first).
4139 * In this case, the result of this method with localaddr NULL
4140 * is not reliable.
4141 *
4142 * DO NOT USE THIS FUNCTION with localaddr NULL if at all possible.
4143 */
4144struct ieee80211_sta *ieee80211_find_sta_by_ifaddr(struct ieee80211_hw *hw,
4145 const u8 *addr,
4146 const u8 *localaddr);
4147
4148/**
4149 * ieee80211_sta_block_awake - block station from waking up
4150 * @hw: the hardware
4151 * @pubsta: the station
4152 * @block: whether to block or unblock
4153 *
4154 * Some devices require that all frames that are on the queues
4155 * for a specific station that went to sleep are flushed before
4156 * a poll response or frames after the station woke up can be
4157 * delivered to that it. Note that such frames must be rejected
4158 * by the driver as filtered, with the appropriate status flag.
4159 *
4160 * This function allows implementing this mode in a race-free
4161 * manner.
4162 *
4163 * To do this, a driver must keep track of the number of frames
4164 * still enqueued for a specific station. If this number is not
4165 * zero when the station goes to sleep, the driver must call
4166 * this function to force mac80211 to consider the station to
4167 * be asleep regardless of the station's actual state. Once the
4168 * number of outstanding frames reaches zero, the driver must
4169 * call this function again to unblock the station. That will
4170 * cause mac80211 to be able to send ps-poll responses, and if
4171 * the station queried in the meantime then frames will also
4172 * be sent out as a result of this. Additionally, the driver
4173 * will be notified that the station woke up some time after
4174 * it is unblocked, regardless of whether the station actually
4175 * woke up while blocked or not.
4176 */
4177void ieee80211_sta_block_awake(struct ieee80211_hw *hw,
4178 struct ieee80211_sta *pubsta, bool block);
4179
4180/**
4181 * ieee80211_sta_eosp - notify mac80211 about end of SP
4182 * @pubsta: the station
4183 *
4184 * When a device transmits frames in a way that it can't tell
4185 * mac80211 in the TX status about the EOSP, it must clear the
4186 * %IEEE80211_TX_STATUS_EOSP bit and call this function instead.
4187 * This applies for PS-Poll as well as uAPSD.
4188 *
4189 * Note that just like with _tx_status() and _rx() drivers must
4190 * not mix calls to irqsafe/non-irqsafe versions, this function
4191 * must not be mixed with those either. Use the all irqsafe, or
4192 * all non-irqsafe, don't mix!
4193 *
4194 * NB: the _irqsafe version of this function doesn't exist, no
4195 * driver needs it right now. Don't call this function if
4196 * you'd need the _irqsafe version, look at the git history
4197 * and restore the _irqsafe version!
4198 */
4199void ieee80211_sta_eosp(struct ieee80211_sta *pubsta);
4200
4201/**
4202 * ieee80211_iter_keys - iterate keys programmed into the device
4203 * @hw: pointer obtained from ieee80211_alloc_hw()
4204 * @vif: virtual interface to iterate, may be %NULL for all
4205 * @iter: iterator function that will be called for each key
4206 * @iter_data: custom data to pass to the iterator function
4207 *
4208 * This function can be used to iterate all the keys known to
4209 * mac80211, even those that weren't previously programmed into
4210 * the device. This is intended for use in WoWLAN if the device
4211 * needs reprogramming of the keys during suspend. Note that due
4212 * to locking reasons, it is also only safe to call this at few
4213 * spots since it must hold the RTNL and be able to sleep.
4214 *
4215 * The order in which the keys are iterated matches the order
4216 * in which they were originally installed and handed to the
4217 * set_key callback.
4218 */
4219void ieee80211_iter_keys(struct ieee80211_hw *hw,
4220 struct ieee80211_vif *vif,
4221 void (*iter)(struct ieee80211_hw *hw,
4222 struct ieee80211_vif *vif,
4223 struct ieee80211_sta *sta,
4224 struct ieee80211_key_conf *key,
4225 void *data),
4226 void *iter_data);
4227
4228/**
4229 * ieee80211_iter_chan_contexts_atomic - iterate channel contexts
4230 * @hw: pointre obtained from ieee80211_alloc_hw().
4231 * @iter: iterator function
4232 * @iter_data: data passed to iterator function
4233 *
4234 * Iterate all active channel contexts. This function is atomic and
4235 * doesn't acquire any locks internally that might be held in other
4236 * places while calling into the driver.
4237 *
4238 * The iterator will not find a context that's being added (during
4239 * the driver callback to add it) but will find it while it's being
4240 * removed.
4241 *
4242 * Note that during hardware restart, all contexts that existed
4243 * before the restart are considered already present so will be
4244 * found while iterating, whether they've been re-added already
4245 * or not.
4246 */
4247void ieee80211_iter_chan_contexts_atomic(
4248 struct ieee80211_hw *hw,
4249 void (*iter)(struct ieee80211_hw *hw,
4250 struct ieee80211_chanctx_conf *chanctx_conf,
4251 void *data),
4252 void *iter_data);
4253
4254/**
4255 * ieee80211_ap_probereq_get - retrieve a Probe Request template
4256 * @hw: pointer obtained from ieee80211_alloc_hw().
4257 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4258 *
4259 * Creates a Probe Request template which can, for example, be uploaded to
4260 * hardware. The template is filled with bssid, ssid and supported rate
4261 * information. This function must only be called from within the
4262 * .bss_info_changed callback function and only in managed mode. The function
4263 * is only useful when the interface is associated, otherwise it will return
4264 * %NULL.
4265 *
4266 * Return: The Probe Request template. %NULL on error.
4267 */
4268struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw,
4269 struct ieee80211_vif *vif);
4270
4271/**
4272 * ieee80211_beacon_loss - inform hardware does not receive beacons
4273 *
4274 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4275 *
4276 * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER and
4277 * %IEEE80211_CONF_PS is set, the driver needs to inform whenever the
4278 * hardware is not receiving beacons with this function.
4279 */
4280void ieee80211_beacon_loss(struct ieee80211_vif *vif);
4281
4282/**
4283 * ieee80211_connection_loss - inform hardware has lost connection to the AP
4284 *
4285 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4286 *
4287 * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER, and
4288 * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver
4289 * needs to inform if the connection to the AP has been lost.
4290 * The function may also be called if the connection needs to be terminated
4291 * for some other reason, even if %IEEE80211_HW_CONNECTION_MONITOR isn't set.
4292 *
4293 * This function will cause immediate change to disassociated state,
4294 * without connection recovery attempts.
4295 */
4296void ieee80211_connection_loss(struct ieee80211_vif *vif);
4297
4298/**
4299 * ieee80211_resume_disconnect - disconnect from AP after resume
4300 *
4301 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4302 *
4303 * Instructs mac80211 to disconnect from the AP after resume.
4304 * Drivers can use this after WoWLAN if they know that the
4305 * connection cannot be kept up, for example because keys were
4306 * used while the device was asleep but the replay counters or
4307 * similar cannot be retrieved from the device during resume.
4308 *
4309 * Note that due to implementation issues, if the driver uses
4310 * the reconfiguration functionality during resume the interface
4311 * will still be added as associated first during resume and then
4312 * disconnect normally later.
4313 *
4314 * This function can only be called from the resume callback and
4315 * the driver must not be holding any of its own locks while it
4316 * calls this function, or at least not any locks it needs in the
4317 * key configuration paths (if it supports HW crypto).
4318 */
4319void ieee80211_resume_disconnect(struct ieee80211_vif *vif);
4320
4321/**
4322 * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring
4323 * rssi threshold triggered
4324 *
4325 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4326 * @rssi_event: the RSSI trigger event type
4327 * @gfp: context flags
4328 *
4329 * When the %IEEE80211_VIF_SUPPORTS_CQM_RSSI is set, and a connection quality
4330 * monitoring is configured with an rssi threshold, the driver will inform
4331 * whenever the rssi level reaches the threshold.
4332 */
4333void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif,
4334 enum nl80211_cqm_rssi_threshold_event rssi_event,
4335 gfp_t gfp);
4336
4337/**
4338 * ieee80211_radar_detected - inform that a radar was detected
4339 *
4340 * @hw: pointer as obtained from ieee80211_alloc_hw()
4341 */
4342void ieee80211_radar_detected(struct ieee80211_hw *hw);
4343
4344/**
4345 * ieee80211_chswitch_done - Complete channel switch process
4346 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4347 * @success: make the channel switch successful or not
4348 *
4349 * Complete the channel switch post-process: set the new operational channel
4350 * and wake up the suspended queues.
4351 */
4352void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success);
4353
4354/**
4355 * ieee80211_request_smps - request SM PS transition
4356 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4357 * @smps_mode: new SM PS mode
4358 *
4359 * This allows the driver to request an SM PS transition in managed
4360 * mode. This is useful when the driver has more information than
4361 * the stack about possible interference, for example by bluetooth.
4362 */
4363void ieee80211_request_smps(struct ieee80211_vif *vif,
4364 enum ieee80211_smps_mode smps_mode);
4365
4366/**
4367 * ieee80211_ready_on_channel - notification of remain-on-channel start
4368 * @hw: pointer as obtained from ieee80211_alloc_hw()
4369 */
4370void ieee80211_ready_on_channel(struct ieee80211_hw *hw);
4371
4372/**
4373 * ieee80211_remain_on_channel_expired - remain_on_channel duration expired
4374 * @hw: pointer as obtained from ieee80211_alloc_hw()
4375 */
4376void ieee80211_remain_on_channel_expired(struct ieee80211_hw *hw);
4377
4378/**
4379 * ieee80211_stop_rx_ba_session - callback to stop existing BA sessions
4380 *
4381 * in order not to harm the system performance and user experience, the device
4382 * may request not to allow any rx ba session and tear down existing rx ba
4383 * sessions based on system constraints such as periodic BT activity that needs
4384 * to limit wlan activity (eg.sco or a2dp)."
4385 * in such cases, the intention is to limit the duration of the rx ppdu and
4386 * therefore prevent the peer device to use a-mpdu aggregation.
4387 *
4388 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4389 * @ba_rx_bitmap: Bit map of open rx ba per tid
4390 * @addr: & to bssid mac address
4391 */
4392void ieee80211_stop_rx_ba_session(struct ieee80211_vif *vif, u16 ba_rx_bitmap,
4393 const u8 *addr);
4394
4395/**
4396 * ieee80211_send_bar - send a BlockAckReq frame
4397 *
4398 * can be used to flush pending frames from the peer's aggregation reorder
4399 * buffer.
4400 *
4401 * @vif: &struct ieee80211_vif pointer from the add_interface callback.
4402 * @ra: the peer's destination address
4403 * @tid: the TID of the aggregation session
4404 * @ssn: the new starting sequence number for the receiver
4405 */
4406void ieee80211_send_bar(struct ieee80211_vif *vif, u8 *ra, u16 tid, u16 ssn);
4407
4408/* Rate control API */
4409
4410/**
4411 * struct ieee80211_tx_rate_control - rate control information for/from RC algo
4412 *
4413 * @hw: The hardware the algorithm is invoked for.
4414 * @sband: The band this frame is being transmitted on.
4415 * @bss_conf: the current BSS configuration
4416 * @skb: the skb that will be transmitted, the control information in it needs
4417 * to be filled in
4418 * @reported_rate: The rate control algorithm can fill this in to indicate
4419 * which rate should be reported to userspace as the current rate and
4420 * used for rate calculations in the mesh network.
4421 * @rts: whether RTS will be used for this frame because it is longer than the
4422 * RTS threshold
4423 * @short_preamble: whether mac80211 will request short-preamble transmission
4424 * if the selected rate supports it
4425 * @max_rate_idx: user-requested maximum (legacy) rate
4426 * (deprecated; this will be removed once drivers get updated to use
4427 * rate_idx_mask)
4428 * @rate_idx_mask: user-requested (legacy) rate mask
4429 * @rate_idx_mcs_mask: user-requested MCS rate mask (NULL if not in use)
4430 * @bss: whether this frame is sent out in AP or IBSS mode
4431 */
4432struct ieee80211_tx_rate_control {
4433 struct ieee80211_hw *hw;
4434 struct ieee80211_supported_band *sband;
4435 struct ieee80211_bss_conf *bss_conf;
4436 struct sk_buff *skb;
4437 struct ieee80211_tx_rate reported_rate;
4438 bool rts, short_preamble;
4439 u8 max_rate_idx;
4440 u32 rate_idx_mask;
4441 u8 *rate_idx_mcs_mask;
4442 bool bss;
4443};
4444
4445struct rate_control_ops {
4446 const char *name;
4447 void *(*alloc)(struct ieee80211_hw *hw, struct dentry *debugfsdir);
4448 void (*free)(void *priv);
4449
4450 void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp);
4451 void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
4452 struct cfg80211_chan_def *chandef,
4453 struct ieee80211_sta *sta, void *priv_sta);
4454 void (*rate_update)(void *priv, struct ieee80211_supported_band *sband,
4455 struct cfg80211_chan_def *chandef,
4456 struct ieee80211_sta *sta, void *priv_sta,
4457 u32 changed);
4458 void (*free_sta)(void *priv, struct ieee80211_sta *sta,
4459 void *priv_sta);
4460
4461 void (*tx_status)(void *priv, struct ieee80211_supported_band *sband,
4462 struct ieee80211_sta *sta, void *priv_sta,
4463 struct sk_buff *skb);
4464 void (*get_rate)(void *priv, struct ieee80211_sta *sta, void *priv_sta,
4465 struct ieee80211_tx_rate_control *txrc);
4466
4467 void (*add_sta_debugfs)(void *priv, void *priv_sta,
4468 struct dentry *dir);
4469 void (*remove_sta_debugfs)(void *priv, void *priv_sta);
4470};
4471
4472static inline int rate_supported(struct ieee80211_sta *sta,
4473 enum ieee80211_band band,
4474 int index)
4475{
4476 return (sta == NULL || sta->supp_rates[band] & BIT(index));
4477}
4478
4479/**
4480 * rate_control_send_low - helper for drivers for management/no-ack frames
4481 *
4482 * Rate control algorithms that agree to use the lowest rate to
4483 * send management frames and NO_ACK data with the respective hw
4484 * retries should use this in the beginning of their mac80211 get_rate
4485 * callback. If true is returned the rate control can simply return.
4486 * If false is returned we guarantee that sta and sta and priv_sta is
4487 * not null.
4488 *
4489 * Rate control algorithms wishing to do more intelligent selection of
4490 * rate for multicast/broadcast frames may choose to not use this.
4491 *
4492 * @sta: &struct ieee80211_sta pointer to the target destination. Note
4493 * that this may be null.
4494 * @priv_sta: private rate control structure. This may be null.
4495 * @txrc: rate control information we sholud populate for mac80211.
4496 */
4497bool rate_control_send_low(struct ieee80211_sta *sta,
4498 void *priv_sta,
4499 struct ieee80211_tx_rate_control *txrc);
4500
4501
4502static inline s8
4503rate_lowest_index(struct ieee80211_supported_band *sband,
4504 struct ieee80211_sta *sta)
4505{
4506 int i;
4507
4508 for (i = 0; i < sband->n_bitrates; i++)
4509 if (rate_supported(sta, sband->band, i))
4510 return i;
4511
4512 /* warn when we cannot find a rate. */
4513 WARN_ON_ONCE(1);
4514
4515 /* and return 0 (the lowest index) */
4516 return 0;
4517}
4518
4519static inline
4520bool rate_usable_index_exists(struct ieee80211_supported_band *sband,
4521 struct ieee80211_sta *sta)
4522{
4523 unsigned int i;
4524
4525 for (i = 0; i < sband->n_bitrates; i++)
4526 if (rate_supported(sta, sband->band, i))
4527 return true;
4528 return false;
4529}
4530
4531/**
4532 * rate_control_set_rates - pass the sta rate selection to mac80211/driver
4533 *
4534 * When not doing a rate control probe to test rates, rate control should pass
4535 * its rate selection to mac80211. If the driver supports receiving a station
4536 * rate table, it will use it to ensure that frames are always sent based on
4537 * the most recent rate control module decision.
4538 *
4539 * @hw: pointer as obtained from ieee80211_alloc_hw()
4540 * @pubsta: &struct ieee80211_sta pointer to the target destination.
4541 * @rates: new tx rate set to be used for this station.
4542 */
4543int rate_control_set_rates(struct ieee80211_hw *hw,
4544 struct ieee80211_sta *pubsta,
4545 struct ieee80211_sta_rates *rates);
4546
4547int ieee80211_rate_control_register(const struct rate_control_ops *ops);
4548void ieee80211_rate_control_unregister(const struct rate_control_ops *ops);
4549
4550static inline bool
4551conf_is_ht20(struct ieee80211_conf *conf)
4552{
4553 return conf->chandef.width == NL80211_CHAN_WIDTH_20;
4554}
4555
4556static inline bool
4557conf_is_ht40_minus(struct ieee80211_conf *conf)
4558{
4559 return conf->chandef.width == NL80211_CHAN_WIDTH_40 &&
4560 conf->chandef.center_freq1 < conf->chandef.chan->center_freq;
4561}
4562
4563static inline bool
4564conf_is_ht40_plus(struct ieee80211_conf *conf)
4565{
4566 return conf->chandef.width == NL80211_CHAN_WIDTH_40 &&
4567 conf->chandef.center_freq1 > conf->chandef.chan->center_freq;
4568}
4569
4570static inline bool
4571conf_is_ht40(struct ieee80211_conf *conf)
4572{
4573 return conf->chandef.width == NL80211_CHAN_WIDTH_40;
4574}
4575
4576static inline bool
4577conf_is_ht(struct ieee80211_conf *conf)
4578{
4579 return conf->chandef.width != NL80211_CHAN_WIDTH_20_NOHT;
4580}
4581
4582static inline enum nl80211_iftype
4583ieee80211_iftype_p2p(enum nl80211_iftype type, bool p2p)
4584{
4585 if (p2p) {
4586 switch (type) {
4587 case NL80211_IFTYPE_STATION:
4588 return NL80211_IFTYPE_P2P_CLIENT;
4589 case NL80211_IFTYPE_AP:
4590 return NL80211_IFTYPE_P2P_GO;
4591 default:
4592 break;
4593 }
4594 }
4595 return type;
4596}
4597
4598static inline enum nl80211_iftype
4599ieee80211_vif_type_p2p(struct ieee80211_vif *vif)
4600{
4601 return ieee80211_iftype_p2p(vif->type, vif->p2p);
4602}
4603
4604void ieee80211_enable_rssi_reports(struct ieee80211_vif *vif,
4605 int rssi_min_thold,
4606 int rssi_max_thold);
4607
4608void ieee80211_disable_rssi_reports(struct ieee80211_vif *vif);
4609
4610/**
4611 * ieee80211_ave_rssi - report the average RSSI for the specified interface
4612 *
4613 * @vif: the specified virtual interface
4614 *
4615 * Note: This function assumes that the given vif is valid.
4616 *
4617 * Return: The average RSSI value for the requested interface, or 0 if not
4618 * applicable.
4619 */
4620int ieee80211_ave_rssi(struct ieee80211_vif *vif);
4621
4622/**
4623 * ieee80211_report_wowlan_wakeup - report WoWLAN wakeup
4624 * @vif: virtual interface
4625 * @wakeup: wakeup reason(s)
4626 * @gfp: allocation flags
4627 *
4628 * See cfg80211_report_wowlan_wakeup().
4629 */
4630void ieee80211_report_wowlan_wakeup(struct ieee80211_vif *vif,
4631 struct cfg80211_wowlan_wakeup *wakeup,
4632 gfp_t gfp);
4633
4634/**
4635 * ieee80211_tx_prepare_skb - prepare an 802.11 skb for transmission
4636 * @hw: pointer as obtained from ieee80211_alloc_hw()
4637 * @vif: virtual interface
4638 * @skb: frame to be sent from within the driver
4639 * @band: the band to transmit on
4640 * @sta: optional pointer to get the station to send the frame to
4641 *
4642 * Note: must be called under RCU lock
4643 */
4644bool ieee80211_tx_prepare_skb(struct ieee80211_hw *hw,
4645 struct ieee80211_vif *vif, struct sk_buff *skb,
4646 int band, struct ieee80211_sta **sta);
4647
4648/**
4649 * struct ieee80211_noa_data - holds temporary data for tracking P2P NoA state
4650 *
4651 * @next_tsf: TSF timestamp of the next absent state change
4652 * @has_next_tsf: next absent state change event pending
4653 *
4654 * @absent: descriptor bitmask, set if GO is currently absent
4655 *
4656 * private:
4657 *
4658 * @count: count fields from the NoA descriptors
4659 * @desc: adjusted data from the NoA
4660 */
4661struct ieee80211_noa_data {
4662 u32 next_tsf;
4663 bool has_next_tsf;
4664
4665 u8 absent;
4666
4667 u8 count[IEEE80211_P2P_NOA_DESC_MAX];
4668 struct {
4669 u32 start;
4670 u32 duration;
4671 u32 interval;
4672 } desc[IEEE80211_P2P_NOA_DESC_MAX];
4673};
4674
4675/**
4676 * ieee80211_parse_p2p_noa - initialize NoA tracking data from P2P IE
4677 *
4678 * @attr: P2P NoA IE
4679 * @data: NoA tracking data
4680 * @tsf: current TSF timestamp
4681 *
4682 * Return: number of successfully parsed descriptors
4683 */
4684int ieee80211_parse_p2p_noa(const struct ieee80211_p2p_noa_attr *attr,
4685 struct ieee80211_noa_data *data, u32 tsf);
4686
4687/**
4688 * ieee80211_update_p2p_noa - get next pending P2P GO absent state change
4689 *
4690 * @data: NoA tracking data
4691 * @tsf: current TSF timestamp
4692 */
4693void ieee80211_update_p2p_noa(struct ieee80211_noa_data *data, u32 tsf);
4694
4695#endif /* MAC80211_H */