Loading...
1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * Driver for Atmel AT91 Serial ports
4 * Copyright (C) 2003 Rick Bronson
5 *
6 * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd.
7 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
8 *
9 * DMA support added by Chip Coldwell.
10 */
11#include <linux/tty.h>
12#include <linux/ioport.h>
13#include <linux/slab.h>
14#include <linux/init.h>
15#include <linux/serial.h>
16#include <linux/clk.h>
17#include <linux/console.h>
18#include <linux/sysrq.h>
19#include <linux/tty_flip.h>
20#include <linux/platform_device.h>
21#include <linux/of.h>
22#include <linux/of_device.h>
23#include <linux/of_gpio.h>
24#include <linux/dma-mapping.h>
25#include <linux/dmaengine.h>
26#include <linux/atmel_pdc.h>
27#include <linux/uaccess.h>
28#include <linux/platform_data/atmel.h>
29#include <linux/timer.h>
30#include <linux/gpio.h>
31#include <linux/gpio/consumer.h>
32#include <linux/err.h>
33#include <linux/irq.h>
34#include <linux/suspend.h>
35#include <linux/mm.h>
36
37#include <asm/div64.h>
38#include <asm/io.h>
39#include <asm/ioctls.h>
40
41#define PDC_BUFFER_SIZE 512
42/* Revisit: We should calculate this based on the actual port settings */
43#define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */
44
45/* The minium number of data FIFOs should be able to contain */
46#define ATMEL_MIN_FIFO_SIZE 8
47/*
48 * These two offsets are substracted from the RX FIFO size to define the RTS
49 * high and low thresholds
50 */
51#define ATMEL_RTS_HIGH_OFFSET 16
52#define ATMEL_RTS_LOW_OFFSET 20
53
54#if defined(CONFIG_SERIAL_ATMEL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
55#define SUPPORT_SYSRQ
56#endif
57
58#include <linux/serial_core.h>
59
60#include "serial_mctrl_gpio.h"
61#include "atmel_serial.h"
62
63static void atmel_start_rx(struct uart_port *port);
64static void atmel_stop_rx(struct uart_port *port);
65
66#ifdef CONFIG_SERIAL_ATMEL_TTYAT
67
68/* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we
69 * should coexist with the 8250 driver, such as if we have an external 16C550
70 * UART. */
71#define SERIAL_ATMEL_MAJOR 204
72#define MINOR_START 154
73#define ATMEL_DEVICENAME "ttyAT"
74
75#else
76
77/* Use device name ttyS, major 4, minor 64-68. This is the usual serial port
78 * name, but it is legally reserved for the 8250 driver. */
79#define SERIAL_ATMEL_MAJOR TTY_MAJOR
80#define MINOR_START 64
81#define ATMEL_DEVICENAME "ttyS"
82
83#endif
84
85#define ATMEL_ISR_PASS_LIMIT 256
86
87struct atmel_dma_buffer {
88 unsigned char *buf;
89 dma_addr_t dma_addr;
90 unsigned int dma_size;
91 unsigned int ofs;
92};
93
94struct atmel_uart_char {
95 u16 status;
96 u16 ch;
97};
98
99/*
100 * Be careful, the real size of the ring buffer is
101 * sizeof(atmel_uart_char) * ATMEL_SERIAL_RINGSIZE. It means that ring buffer
102 * can contain up to 1024 characters in PIO mode and up to 4096 characters in
103 * DMA mode.
104 */
105#define ATMEL_SERIAL_RINGSIZE 1024
106
107/*
108 * at91: 6 USARTs and one DBGU port (SAM9260)
109 * samx7: 3 USARTs and 5 UARTs
110 */
111#define ATMEL_MAX_UART 8
112
113/*
114 * We wrap our port structure around the generic uart_port.
115 */
116struct atmel_uart_port {
117 struct uart_port uart; /* uart */
118 struct clk *clk; /* uart clock */
119 int may_wakeup; /* cached value of device_may_wakeup for times we need to disable it */
120 u32 backup_imr; /* IMR saved during suspend */
121 int break_active; /* break being received */
122
123 bool use_dma_rx; /* enable DMA receiver */
124 bool use_pdc_rx; /* enable PDC receiver */
125 short pdc_rx_idx; /* current PDC RX buffer */
126 struct atmel_dma_buffer pdc_rx[2]; /* PDC receier */
127
128 bool use_dma_tx; /* enable DMA transmitter */
129 bool use_pdc_tx; /* enable PDC transmitter */
130 struct atmel_dma_buffer pdc_tx; /* PDC transmitter */
131
132 spinlock_t lock_tx; /* port lock */
133 spinlock_t lock_rx; /* port lock */
134 struct dma_chan *chan_tx;
135 struct dma_chan *chan_rx;
136 struct dma_async_tx_descriptor *desc_tx;
137 struct dma_async_tx_descriptor *desc_rx;
138 dma_cookie_t cookie_tx;
139 dma_cookie_t cookie_rx;
140 struct scatterlist sg_tx;
141 struct scatterlist sg_rx;
142 struct tasklet_struct tasklet_rx;
143 struct tasklet_struct tasklet_tx;
144 atomic_t tasklet_shutdown;
145 unsigned int irq_status_prev;
146 unsigned int tx_len;
147
148 struct circ_buf rx_ring;
149
150 struct mctrl_gpios *gpios;
151 u32 backup_mode; /* MR saved during iso7816 operations */
152 u32 backup_brgr; /* BRGR saved during iso7816 operations */
153 unsigned int tx_done_mask;
154 u32 fifo_size;
155 u32 rts_high;
156 u32 rts_low;
157 bool ms_irq_enabled;
158 u32 rtor; /* address of receiver timeout register if it exists */
159 bool has_frac_baudrate;
160 bool has_hw_timer;
161 struct timer_list uart_timer;
162
163 bool tx_stopped;
164 bool suspended;
165 unsigned int pending;
166 unsigned int pending_status;
167 spinlock_t lock_suspended;
168
169 bool hd_start_rx; /* can start RX during half-duplex operation */
170
171 /* ISO7816 */
172 unsigned int fidi_min;
173 unsigned int fidi_max;
174
175#ifdef CONFIG_PM
176 struct {
177 u32 cr;
178 u32 mr;
179 u32 imr;
180 u32 brgr;
181 u32 rtor;
182 u32 ttgr;
183 u32 fmr;
184 u32 fimr;
185 } cache;
186#endif
187
188 int (*prepare_rx)(struct uart_port *port);
189 int (*prepare_tx)(struct uart_port *port);
190 void (*schedule_rx)(struct uart_port *port);
191 void (*schedule_tx)(struct uart_port *port);
192 void (*release_rx)(struct uart_port *port);
193 void (*release_tx)(struct uart_port *port);
194};
195
196static struct atmel_uart_port atmel_ports[ATMEL_MAX_UART];
197static DECLARE_BITMAP(atmel_ports_in_use, ATMEL_MAX_UART);
198
199#ifdef SUPPORT_SYSRQ
200static struct console atmel_console;
201#endif
202
203#if defined(CONFIG_OF)
204static const struct of_device_id atmel_serial_dt_ids[] = {
205 { .compatible = "atmel,at91rm9200-usart-serial" },
206 { /* sentinel */ }
207};
208#endif
209
210static inline struct atmel_uart_port *
211to_atmel_uart_port(struct uart_port *uart)
212{
213 return container_of(uart, struct atmel_uart_port, uart);
214}
215
216static inline u32 atmel_uart_readl(struct uart_port *port, u32 reg)
217{
218 return __raw_readl(port->membase + reg);
219}
220
221static inline void atmel_uart_writel(struct uart_port *port, u32 reg, u32 value)
222{
223 __raw_writel(value, port->membase + reg);
224}
225
226static inline u8 atmel_uart_read_char(struct uart_port *port)
227{
228 return __raw_readb(port->membase + ATMEL_US_RHR);
229}
230
231static inline void atmel_uart_write_char(struct uart_port *port, u8 value)
232{
233 __raw_writeb(value, port->membase + ATMEL_US_THR);
234}
235
236static inline int atmel_uart_is_half_duplex(struct uart_port *port)
237{
238 return ((port->rs485.flags & SER_RS485_ENABLED) &&
239 !(port->rs485.flags & SER_RS485_RX_DURING_TX)) ||
240 (port->iso7816.flags & SER_ISO7816_ENABLED);
241}
242
243#ifdef CONFIG_SERIAL_ATMEL_PDC
244static bool atmel_use_pdc_rx(struct uart_port *port)
245{
246 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
247
248 return atmel_port->use_pdc_rx;
249}
250
251static bool atmel_use_pdc_tx(struct uart_port *port)
252{
253 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
254
255 return atmel_port->use_pdc_tx;
256}
257#else
258static bool atmel_use_pdc_rx(struct uart_port *port)
259{
260 return false;
261}
262
263static bool atmel_use_pdc_tx(struct uart_port *port)
264{
265 return false;
266}
267#endif
268
269static bool atmel_use_dma_tx(struct uart_port *port)
270{
271 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
272
273 return atmel_port->use_dma_tx;
274}
275
276static bool atmel_use_dma_rx(struct uart_port *port)
277{
278 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
279
280 return atmel_port->use_dma_rx;
281}
282
283static bool atmel_use_fifo(struct uart_port *port)
284{
285 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
286
287 return atmel_port->fifo_size;
288}
289
290static void atmel_tasklet_schedule(struct atmel_uart_port *atmel_port,
291 struct tasklet_struct *t)
292{
293 if (!atomic_read(&atmel_port->tasklet_shutdown))
294 tasklet_schedule(t);
295}
296
297/* Enable or disable the rs485 support */
298static int atmel_config_rs485(struct uart_port *port,
299 struct serial_rs485 *rs485conf)
300{
301 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
302 unsigned int mode;
303
304 /* Disable interrupts */
305 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
306
307 mode = atmel_uart_readl(port, ATMEL_US_MR);
308
309 /* Resetting serial mode to RS232 (0x0) */
310 mode &= ~ATMEL_US_USMODE;
311
312 port->rs485 = *rs485conf;
313
314 if (rs485conf->flags & SER_RS485_ENABLED) {
315 dev_dbg(port->dev, "Setting UART to RS485\n");
316 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
317 atmel_uart_writel(port, ATMEL_US_TTGR,
318 rs485conf->delay_rts_after_send);
319 mode |= ATMEL_US_USMODE_RS485;
320 } else {
321 dev_dbg(port->dev, "Setting UART to RS232\n");
322 if (atmel_use_pdc_tx(port))
323 atmel_port->tx_done_mask = ATMEL_US_ENDTX |
324 ATMEL_US_TXBUFE;
325 else
326 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
327 }
328 atmel_uart_writel(port, ATMEL_US_MR, mode);
329
330 /* Enable interrupts */
331 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
332
333 return 0;
334}
335
336static unsigned int atmel_calc_cd(struct uart_port *port,
337 struct serial_iso7816 *iso7816conf)
338{
339 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
340 unsigned int cd;
341 u64 mck_rate;
342
343 mck_rate = (u64)clk_get_rate(atmel_port->clk);
344 do_div(mck_rate, iso7816conf->clk);
345 cd = mck_rate;
346 return cd;
347}
348
349static unsigned int atmel_calc_fidi(struct uart_port *port,
350 struct serial_iso7816 *iso7816conf)
351{
352 u64 fidi = 0;
353
354 if (iso7816conf->sc_fi && iso7816conf->sc_di) {
355 fidi = (u64)iso7816conf->sc_fi;
356 do_div(fidi, iso7816conf->sc_di);
357 }
358 return (u32)fidi;
359}
360
361/* Enable or disable the iso7816 support */
362/* Called with interrupts disabled */
363static int atmel_config_iso7816(struct uart_port *port,
364 struct serial_iso7816 *iso7816conf)
365{
366 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
367 unsigned int mode;
368 unsigned int cd, fidi;
369 int ret = 0;
370
371 /* Disable interrupts */
372 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
373
374 mode = atmel_uart_readl(port, ATMEL_US_MR);
375
376 if (iso7816conf->flags & SER_ISO7816_ENABLED) {
377 mode &= ~ATMEL_US_USMODE;
378
379 if (iso7816conf->tg > 255) {
380 dev_err(port->dev, "ISO7816: Timeguard exceeding 255\n");
381 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
382 ret = -EINVAL;
383 goto err_out;
384 }
385
386 if ((iso7816conf->flags & SER_ISO7816_T_PARAM)
387 == SER_ISO7816_T(0)) {
388 mode |= ATMEL_US_USMODE_ISO7816_T0 | ATMEL_US_DSNACK;
389 } else if ((iso7816conf->flags & SER_ISO7816_T_PARAM)
390 == SER_ISO7816_T(1)) {
391 mode |= ATMEL_US_USMODE_ISO7816_T1 | ATMEL_US_INACK;
392 } else {
393 dev_err(port->dev, "ISO7816: Type not supported\n");
394 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
395 ret = -EINVAL;
396 goto err_out;
397 }
398
399 mode &= ~(ATMEL_US_USCLKS | ATMEL_US_NBSTOP | ATMEL_US_PAR);
400
401 /* select mck clock, and output */
402 mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO;
403 /* set parity for normal/inverse mode + max iterations */
404 mode |= ATMEL_US_PAR_EVEN | ATMEL_US_NBSTOP_1 | ATMEL_US_MAX_ITER(3);
405
406 cd = atmel_calc_cd(port, iso7816conf);
407 fidi = atmel_calc_fidi(port, iso7816conf);
408 if (fidi == 0) {
409 dev_warn(port->dev, "ISO7816 fidi = 0, Generator generates no signal\n");
410 } else if (fidi < atmel_port->fidi_min
411 || fidi > atmel_port->fidi_max) {
412 dev_err(port->dev, "ISO7816 fidi = %u, value not supported\n", fidi);
413 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
414 ret = -EINVAL;
415 goto err_out;
416 }
417
418 if (!(port->iso7816.flags & SER_ISO7816_ENABLED)) {
419 /* port not yet in iso7816 mode: store configuration */
420 atmel_port->backup_mode = atmel_uart_readl(port, ATMEL_US_MR);
421 atmel_port->backup_brgr = atmel_uart_readl(port, ATMEL_US_BRGR);
422 }
423
424 atmel_uart_writel(port, ATMEL_US_TTGR, iso7816conf->tg);
425 atmel_uart_writel(port, ATMEL_US_BRGR, cd);
426 atmel_uart_writel(port, ATMEL_US_FIDI, fidi);
427
428 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXEN);
429 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY | ATMEL_US_NACK | ATMEL_US_ITERATION;
430 } else {
431 dev_dbg(port->dev, "Setting UART back to RS232\n");
432 /* back to last RS232 settings */
433 mode = atmel_port->backup_mode;
434 memset(iso7816conf, 0, sizeof(struct serial_iso7816));
435 atmel_uart_writel(port, ATMEL_US_TTGR, 0);
436 atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->backup_brgr);
437 atmel_uart_writel(port, ATMEL_US_FIDI, 0x174);
438
439 if (atmel_use_pdc_tx(port))
440 atmel_port->tx_done_mask = ATMEL_US_ENDTX |
441 ATMEL_US_TXBUFE;
442 else
443 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
444 }
445
446 port->iso7816 = *iso7816conf;
447
448 atmel_uart_writel(port, ATMEL_US_MR, mode);
449
450err_out:
451 /* Enable interrupts */
452 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
453
454 return ret;
455}
456
457/*
458 * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty.
459 */
460static u_int atmel_tx_empty(struct uart_port *port)
461{
462 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
463
464 if (atmel_port->tx_stopped)
465 return TIOCSER_TEMT;
466 return (atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXEMPTY) ?
467 TIOCSER_TEMT :
468 0;
469}
470
471/*
472 * Set state of the modem control output lines
473 */
474static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
475{
476 unsigned int control = 0;
477 unsigned int mode = atmel_uart_readl(port, ATMEL_US_MR);
478 unsigned int rts_paused, rts_ready;
479 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
480
481 /* override mode to RS485 if needed, otherwise keep the current mode */
482 if (port->rs485.flags & SER_RS485_ENABLED) {
483 atmel_uart_writel(port, ATMEL_US_TTGR,
484 port->rs485.delay_rts_after_send);
485 mode &= ~ATMEL_US_USMODE;
486 mode |= ATMEL_US_USMODE_RS485;
487 }
488
489 /* set the RTS line state according to the mode */
490 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) {
491 /* force RTS line to high level */
492 rts_paused = ATMEL_US_RTSEN;
493
494 /* give the control of the RTS line back to the hardware */
495 rts_ready = ATMEL_US_RTSDIS;
496 } else {
497 /* force RTS line to high level */
498 rts_paused = ATMEL_US_RTSDIS;
499
500 /* force RTS line to low level */
501 rts_ready = ATMEL_US_RTSEN;
502 }
503
504 if (mctrl & TIOCM_RTS)
505 control |= rts_ready;
506 else
507 control |= rts_paused;
508
509 if (mctrl & TIOCM_DTR)
510 control |= ATMEL_US_DTREN;
511 else
512 control |= ATMEL_US_DTRDIS;
513
514 atmel_uart_writel(port, ATMEL_US_CR, control);
515
516 mctrl_gpio_set(atmel_port->gpios, mctrl);
517
518 /* Local loopback mode? */
519 mode &= ~ATMEL_US_CHMODE;
520 if (mctrl & TIOCM_LOOP)
521 mode |= ATMEL_US_CHMODE_LOC_LOOP;
522 else
523 mode |= ATMEL_US_CHMODE_NORMAL;
524
525 atmel_uart_writel(port, ATMEL_US_MR, mode);
526}
527
528/*
529 * Get state of the modem control input lines
530 */
531static u_int atmel_get_mctrl(struct uart_port *port)
532{
533 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
534 unsigned int ret = 0, status;
535
536 status = atmel_uart_readl(port, ATMEL_US_CSR);
537
538 /*
539 * The control signals are active low.
540 */
541 if (!(status & ATMEL_US_DCD))
542 ret |= TIOCM_CD;
543 if (!(status & ATMEL_US_CTS))
544 ret |= TIOCM_CTS;
545 if (!(status & ATMEL_US_DSR))
546 ret |= TIOCM_DSR;
547 if (!(status & ATMEL_US_RI))
548 ret |= TIOCM_RI;
549
550 return mctrl_gpio_get(atmel_port->gpios, &ret);
551}
552
553/*
554 * Stop transmitting.
555 */
556static void atmel_stop_tx(struct uart_port *port)
557{
558 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
559
560 if (atmel_use_pdc_tx(port)) {
561 /* disable PDC transmit */
562 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
563 }
564
565 /*
566 * Disable the transmitter.
567 * This is mandatory when DMA is used, otherwise the DMA buffer
568 * is fully transmitted.
569 */
570 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS);
571 atmel_port->tx_stopped = true;
572
573 /* Disable interrupts */
574 atmel_uart_writel(port, ATMEL_US_IDR, atmel_port->tx_done_mask);
575
576 if (atmel_uart_is_half_duplex(port))
577 atmel_start_rx(port);
578
579}
580
581/*
582 * Start transmitting.
583 */
584static void atmel_start_tx(struct uart_port *port)
585{
586 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
587
588 if (atmel_use_pdc_tx(port) && (atmel_uart_readl(port, ATMEL_PDC_PTSR)
589 & ATMEL_PDC_TXTEN))
590 /* The transmitter is already running. Yes, we
591 really need this.*/
592 return;
593
594 if (atmel_use_pdc_tx(port) || atmel_use_dma_tx(port))
595 if (atmel_uart_is_half_duplex(port))
596 atmel_stop_rx(port);
597
598 if (atmel_use_pdc_tx(port))
599 /* re-enable PDC transmit */
600 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
601
602 /* Enable interrupts */
603 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->tx_done_mask);
604
605 /* re-enable the transmitter */
606 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
607 atmel_port->tx_stopped = false;
608}
609
610/*
611 * start receiving - port is in process of being opened.
612 */
613static void atmel_start_rx(struct uart_port *port)
614{
615 /* reset status and receiver */
616 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
617
618 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXEN);
619
620 if (atmel_use_pdc_rx(port)) {
621 /* enable PDC controller */
622 atmel_uart_writel(port, ATMEL_US_IER,
623 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
624 port->read_status_mask);
625 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
626 } else {
627 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY);
628 }
629}
630
631/*
632 * Stop receiving - port is in process of being closed.
633 */
634static void atmel_stop_rx(struct uart_port *port)
635{
636 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RXDIS);
637
638 if (atmel_use_pdc_rx(port)) {
639 /* disable PDC receive */
640 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS);
641 atmel_uart_writel(port, ATMEL_US_IDR,
642 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
643 port->read_status_mask);
644 } else {
645 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXRDY);
646 }
647}
648
649/*
650 * Enable modem status interrupts
651 */
652static void atmel_enable_ms(struct uart_port *port)
653{
654 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
655 uint32_t ier = 0;
656
657 /*
658 * Interrupt should not be enabled twice
659 */
660 if (atmel_port->ms_irq_enabled)
661 return;
662
663 atmel_port->ms_irq_enabled = true;
664
665 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
666 ier |= ATMEL_US_CTSIC;
667
668 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR))
669 ier |= ATMEL_US_DSRIC;
670
671 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI))
672 ier |= ATMEL_US_RIIC;
673
674 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD))
675 ier |= ATMEL_US_DCDIC;
676
677 atmel_uart_writel(port, ATMEL_US_IER, ier);
678
679 mctrl_gpio_enable_ms(atmel_port->gpios);
680}
681
682/*
683 * Disable modem status interrupts
684 */
685static void atmel_disable_ms(struct uart_port *port)
686{
687 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
688 uint32_t idr = 0;
689
690 /*
691 * Interrupt should not be disabled twice
692 */
693 if (!atmel_port->ms_irq_enabled)
694 return;
695
696 atmel_port->ms_irq_enabled = false;
697
698 mctrl_gpio_disable_ms(atmel_port->gpios);
699
700 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
701 idr |= ATMEL_US_CTSIC;
702
703 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DSR))
704 idr |= ATMEL_US_DSRIC;
705
706 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_RI))
707 idr |= ATMEL_US_RIIC;
708
709 if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_DCD))
710 idr |= ATMEL_US_DCDIC;
711
712 atmel_uart_writel(port, ATMEL_US_IDR, idr);
713}
714
715/*
716 * Control the transmission of a break signal
717 */
718static void atmel_break_ctl(struct uart_port *port, int break_state)
719{
720 if (break_state != 0)
721 /* start break */
722 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTBRK);
723 else
724 /* stop break */
725 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STPBRK);
726}
727
728/*
729 * Stores the incoming character in the ring buffer
730 */
731static void
732atmel_buffer_rx_char(struct uart_port *port, unsigned int status,
733 unsigned int ch)
734{
735 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
736 struct circ_buf *ring = &atmel_port->rx_ring;
737 struct atmel_uart_char *c;
738
739 if (!CIRC_SPACE(ring->head, ring->tail, ATMEL_SERIAL_RINGSIZE))
740 /* Buffer overflow, ignore char */
741 return;
742
743 c = &((struct atmel_uart_char *)ring->buf)[ring->head];
744 c->status = status;
745 c->ch = ch;
746
747 /* Make sure the character is stored before we update head. */
748 smp_wmb();
749
750 ring->head = (ring->head + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
751}
752
753/*
754 * Deal with parity, framing and overrun errors.
755 */
756static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status)
757{
758 /* clear error */
759 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
760
761 if (status & ATMEL_US_RXBRK) {
762 /* ignore side-effect */
763 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
764 port->icount.brk++;
765 }
766 if (status & ATMEL_US_PARE)
767 port->icount.parity++;
768 if (status & ATMEL_US_FRAME)
769 port->icount.frame++;
770 if (status & ATMEL_US_OVRE)
771 port->icount.overrun++;
772}
773
774/*
775 * Characters received (called from interrupt handler)
776 */
777static void atmel_rx_chars(struct uart_port *port)
778{
779 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
780 unsigned int status, ch;
781
782 status = atmel_uart_readl(port, ATMEL_US_CSR);
783 while (status & ATMEL_US_RXRDY) {
784 ch = atmel_uart_read_char(port);
785
786 /*
787 * note that the error handling code is
788 * out of the main execution path
789 */
790 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
791 | ATMEL_US_OVRE | ATMEL_US_RXBRK)
792 || atmel_port->break_active)) {
793
794 /* clear error */
795 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
796
797 if (status & ATMEL_US_RXBRK
798 && !atmel_port->break_active) {
799 atmel_port->break_active = 1;
800 atmel_uart_writel(port, ATMEL_US_IER,
801 ATMEL_US_RXBRK);
802 } else {
803 /*
804 * This is either the end-of-break
805 * condition or we've received at
806 * least one character without RXBRK
807 * being set. In both cases, the next
808 * RXBRK will indicate start-of-break.
809 */
810 atmel_uart_writel(port, ATMEL_US_IDR,
811 ATMEL_US_RXBRK);
812 status &= ~ATMEL_US_RXBRK;
813 atmel_port->break_active = 0;
814 }
815 }
816
817 atmel_buffer_rx_char(port, status, ch);
818 status = atmel_uart_readl(port, ATMEL_US_CSR);
819 }
820
821 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx);
822}
823
824/*
825 * Transmit characters (called from tasklet with TXRDY interrupt
826 * disabled)
827 */
828static void atmel_tx_chars(struct uart_port *port)
829{
830 struct circ_buf *xmit = &port->state->xmit;
831 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
832
833 if (port->x_char &&
834 (atmel_uart_readl(port, ATMEL_US_CSR) & atmel_port->tx_done_mask)) {
835 atmel_uart_write_char(port, port->x_char);
836 port->icount.tx++;
837 port->x_char = 0;
838 }
839 if (uart_circ_empty(xmit) || uart_tx_stopped(port))
840 return;
841
842 while (atmel_uart_readl(port, ATMEL_US_CSR) &
843 atmel_port->tx_done_mask) {
844 atmel_uart_write_char(port, xmit->buf[xmit->tail]);
845 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
846 port->icount.tx++;
847 if (uart_circ_empty(xmit))
848 break;
849 }
850
851 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
852 uart_write_wakeup(port);
853
854 if (!uart_circ_empty(xmit))
855 /* Enable interrupts */
856 atmel_uart_writel(port, ATMEL_US_IER,
857 atmel_port->tx_done_mask);
858}
859
860static void atmel_complete_tx_dma(void *arg)
861{
862 struct atmel_uart_port *atmel_port = arg;
863 struct uart_port *port = &atmel_port->uart;
864 struct circ_buf *xmit = &port->state->xmit;
865 struct dma_chan *chan = atmel_port->chan_tx;
866 unsigned long flags;
867
868 spin_lock_irqsave(&port->lock, flags);
869
870 if (chan)
871 dmaengine_terminate_all(chan);
872 xmit->tail += atmel_port->tx_len;
873 xmit->tail &= UART_XMIT_SIZE - 1;
874
875 port->icount.tx += atmel_port->tx_len;
876
877 spin_lock_irq(&atmel_port->lock_tx);
878 async_tx_ack(atmel_port->desc_tx);
879 atmel_port->cookie_tx = -EINVAL;
880 atmel_port->desc_tx = NULL;
881 spin_unlock_irq(&atmel_port->lock_tx);
882
883 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
884 uart_write_wakeup(port);
885
886 /*
887 * xmit is a circular buffer so, if we have just send data from
888 * xmit->tail to the end of xmit->buf, now we have to transmit the
889 * remaining data from the beginning of xmit->buf to xmit->head.
890 */
891 if (!uart_circ_empty(xmit))
892 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
893 else if (atmel_uart_is_half_duplex(port)) {
894 /*
895 * DMA done, re-enable TXEMPTY and signal that we can stop
896 * TX and start RX for RS485
897 */
898 atmel_port->hd_start_rx = true;
899 atmel_uart_writel(port, ATMEL_US_IER,
900 atmel_port->tx_done_mask);
901 }
902
903 spin_unlock_irqrestore(&port->lock, flags);
904}
905
906static void atmel_release_tx_dma(struct uart_port *port)
907{
908 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
909 struct dma_chan *chan = atmel_port->chan_tx;
910
911 if (chan) {
912 dmaengine_terminate_all(chan);
913 dma_release_channel(chan);
914 dma_unmap_sg(port->dev, &atmel_port->sg_tx, 1,
915 DMA_TO_DEVICE);
916 }
917
918 atmel_port->desc_tx = NULL;
919 atmel_port->chan_tx = NULL;
920 atmel_port->cookie_tx = -EINVAL;
921}
922
923/*
924 * Called from tasklet with TXRDY interrupt is disabled.
925 */
926static void atmel_tx_dma(struct uart_port *port)
927{
928 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
929 struct circ_buf *xmit = &port->state->xmit;
930 struct dma_chan *chan = atmel_port->chan_tx;
931 struct dma_async_tx_descriptor *desc;
932 struct scatterlist sgl[2], *sg, *sg_tx = &atmel_port->sg_tx;
933 unsigned int tx_len, part1_len, part2_len, sg_len;
934 dma_addr_t phys_addr;
935
936 /* Make sure we have an idle channel */
937 if (atmel_port->desc_tx != NULL)
938 return;
939
940 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
941 /*
942 * DMA is idle now.
943 * Port xmit buffer is already mapped,
944 * and it is one page... Just adjust
945 * offsets and lengths. Since it is a circular buffer,
946 * we have to transmit till the end, and then the rest.
947 * Take the port lock to get a
948 * consistent xmit buffer state.
949 */
950 tx_len = CIRC_CNT_TO_END(xmit->head,
951 xmit->tail,
952 UART_XMIT_SIZE);
953
954 if (atmel_port->fifo_size) {
955 /* multi data mode */
956 part1_len = (tx_len & ~0x3); /* DWORD access */
957 part2_len = (tx_len & 0x3); /* BYTE access */
958 } else {
959 /* single data (legacy) mode */
960 part1_len = 0;
961 part2_len = tx_len; /* BYTE access only */
962 }
963
964 sg_init_table(sgl, 2);
965 sg_len = 0;
966 phys_addr = sg_dma_address(sg_tx) + xmit->tail;
967 if (part1_len) {
968 sg = &sgl[sg_len++];
969 sg_dma_address(sg) = phys_addr;
970 sg_dma_len(sg) = part1_len;
971
972 phys_addr += part1_len;
973 }
974
975 if (part2_len) {
976 sg = &sgl[sg_len++];
977 sg_dma_address(sg) = phys_addr;
978 sg_dma_len(sg) = part2_len;
979 }
980
981 /*
982 * save tx_len so atmel_complete_tx_dma() will increase
983 * xmit->tail correctly
984 */
985 atmel_port->tx_len = tx_len;
986
987 desc = dmaengine_prep_slave_sg(chan,
988 sgl,
989 sg_len,
990 DMA_MEM_TO_DEV,
991 DMA_PREP_INTERRUPT |
992 DMA_CTRL_ACK);
993 if (!desc) {
994 dev_err(port->dev, "Failed to send via dma!\n");
995 return;
996 }
997
998 dma_sync_sg_for_device(port->dev, sg_tx, 1, DMA_TO_DEVICE);
999
1000 atmel_port->desc_tx = desc;
1001 desc->callback = atmel_complete_tx_dma;
1002 desc->callback_param = atmel_port;
1003 atmel_port->cookie_tx = dmaengine_submit(desc);
1004 }
1005
1006 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1007 uart_write_wakeup(port);
1008}
1009
1010static int atmel_prepare_tx_dma(struct uart_port *port)
1011{
1012 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1013 struct device *mfd_dev = port->dev->parent;
1014 dma_cap_mask_t mask;
1015 struct dma_slave_config config;
1016 int ret, nent;
1017
1018 dma_cap_zero(mask);
1019 dma_cap_set(DMA_SLAVE, mask);
1020
1021 atmel_port->chan_tx = dma_request_slave_channel(mfd_dev, "tx");
1022 if (atmel_port->chan_tx == NULL)
1023 goto chan_err;
1024 dev_info(port->dev, "using %s for tx DMA transfers\n",
1025 dma_chan_name(atmel_port->chan_tx));
1026
1027 spin_lock_init(&atmel_port->lock_tx);
1028 sg_init_table(&atmel_port->sg_tx, 1);
1029 /* UART circular tx buffer is an aligned page. */
1030 BUG_ON(!PAGE_ALIGNED(port->state->xmit.buf));
1031 sg_set_page(&atmel_port->sg_tx,
1032 virt_to_page(port->state->xmit.buf),
1033 UART_XMIT_SIZE,
1034 offset_in_page(port->state->xmit.buf));
1035 nent = dma_map_sg(port->dev,
1036 &atmel_port->sg_tx,
1037 1,
1038 DMA_TO_DEVICE);
1039
1040 if (!nent) {
1041 dev_dbg(port->dev, "need to release resource of dma\n");
1042 goto chan_err;
1043 } else {
1044 dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n", __func__,
1045 sg_dma_len(&atmel_port->sg_tx),
1046 port->state->xmit.buf,
1047 &sg_dma_address(&atmel_port->sg_tx));
1048 }
1049
1050 /* Configure the slave DMA */
1051 memset(&config, 0, sizeof(config));
1052 config.direction = DMA_MEM_TO_DEV;
1053 config.dst_addr_width = (atmel_port->fifo_size) ?
1054 DMA_SLAVE_BUSWIDTH_4_BYTES :
1055 DMA_SLAVE_BUSWIDTH_1_BYTE;
1056 config.dst_addr = port->mapbase + ATMEL_US_THR;
1057 config.dst_maxburst = 1;
1058
1059 ret = dmaengine_slave_config(atmel_port->chan_tx,
1060 &config);
1061 if (ret) {
1062 dev_err(port->dev, "DMA tx slave configuration failed\n");
1063 goto chan_err;
1064 }
1065
1066 return 0;
1067
1068chan_err:
1069 dev_err(port->dev, "TX channel not available, switch to pio\n");
1070 atmel_port->use_dma_tx = 0;
1071 if (atmel_port->chan_tx)
1072 atmel_release_tx_dma(port);
1073 return -EINVAL;
1074}
1075
1076static void atmel_complete_rx_dma(void *arg)
1077{
1078 struct uart_port *port = arg;
1079 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1080
1081 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx);
1082}
1083
1084static void atmel_release_rx_dma(struct uart_port *port)
1085{
1086 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1087 struct dma_chan *chan = atmel_port->chan_rx;
1088
1089 if (chan) {
1090 dmaengine_terminate_all(chan);
1091 dma_release_channel(chan);
1092 dma_unmap_sg(port->dev, &atmel_port->sg_rx, 1,
1093 DMA_FROM_DEVICE);
1094 }
1095
1096 atmel_port->desc_rx = NULL;
1097 atmel_port->chan_rx = NULL;
1098 atmel_port->cookie_rx = -EINVAL;
1099}
1100
1101static void atmel_rx_from_dma(struct uart_port *port)
1102{
1103 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1104 struct tty_port *tport = &port->state->port;
1105 struct circ_buf *ring = &atmel_port->rx_ring;
1106 struct dma_chan *chan = atmel_port->chan_rx;
1107 struct dma_tx_state state;
1108 enum dma_status dmastat;
1109 size_t count;
1110
1111
1112 /* Reset the UART timeout early so that we don't miss one */
1113 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1114 dmastat = dmaengine_tx_status(chan,
1115 atmel_port->cookie_rx,
1116 &state);
1117 /* Restart a new tasklet if DMA status is error */
1118 if (dmastat == DMA_ERROR) {
1119 dev_dbg(port->dev, "Get residue error, restart tasklet\n");
1120 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT);
1121 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_rx);
1122 return;
1123 }
1124
1125 /* CPU claims ownership of RX DMA buffer */
1126 dma_sync_sg_for_cpu(port->dev,
1127 &atmel_port->sg_rx,
1128 1,
1129 DMA_FROM_DEVICE);
1130
1131 /*
1132 * ring->head points to the end of data already written by the DMA.
1133 * ring->tail points to the beginning of data to be read by the
1134 * framework.
1135 * The current transfer size should not be larger than the dma buffer
1136 * length.
1137 */
1138 ring->head = sg_dma_len(&atmel_port->sg_rx) - state.residue;
1139 BUG_ON(ring->head > sg_dma_len(&atmel_port->sg_rx));
1140 /*
1141 * At this point ring->head may point to the first byte right after the
1142 * last byte of the dma buffer:
1143 * 0 <= ring->head <= sg_dma_len(&atmel_port->sg_rx)
1144 *
1145 * However ring->tail must always points inside the dma buffer:
1146 * 0 <= ring->tail <= sg_dma_len(&atmel_port->sg_rx) - 1
1147 *
1148 * Since we use a ring buffer, we have to handle the case
1149 * where head is lower than tail. In such a case, we first read from
1150 * tail to the end of the buffer then reset tail.
1151 */
1152 if (ring->head < ring->tail) {
1153 count = sg_dma_len(&atmel_port->sg_rx) - ring->tail;
1154
1155 tty_insert_flip_string(tport, ring->buf + ring->tail, count);
1156 ring->tail = 0;
1157 port->icount.rx += count;
1158 }
1159
1160 /* Finally we read data from tail to head */
1161 if (ring->tail < ring->head) {
1162 count = ring->head - ring->tail;
1163
1164 tty_insert_flip_string(tport, ring->buf + ring->tail, count);
1165 /* Wrap ring->head if needed */
1166 if (ring->head >= sg_dma_len(&atmel_port->sg_rx))
1167 ring->head = 0;
1168 ring->tail = ring->head;
1169 port->icount.rx += count;
1170 }
1171
1172 /* USART retreives ownership of RX DMA buffer */
1173 dma_sync_sg_for_device(port->dev,
1174 &atmel_port->sg_rx,
1175 1,
1176 DMA_FROM_DEVICE);
1177
1178 /*
1179 * Drop the lock here since it might end up calling
1180 * uart_start(), which takes the lock.
1181 */
1182 spin_unlock(&port->lock);
1183 tty_flip_buffer_push(tport);
1184 spin_lock(&port->lock);
1185
1186 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_TIMEOUT);
1187}
1188
1189static int atmel_prepare_rx_dma(struct uart_port *port)
1190{
1191 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1192 struct device *mfd_dev = port->dev->parent;
1193 struct dma_async_tx_descriptor *desc;
1194 dma_cap_mask_t mask;
1195 struct dma_slave_config config;
1196 struct circ_buf *ring;
1197 int ret, nent;
1198
1199 ring = &atmel_port->rx_ring;
1200
1201 dma_cap_zero(mask);
1202 dma_cap_set(DMA_CYCLIC, mask);
1203
1204 atmel_port->chan_rx = dma_request_slave_channel(mfd_dev, "rx");
1205 if (atmel_port->chan_rx == NULL)
1206 goto chan_err;
1207 dev_info(port->dev, "using %s for rx DMA transfers\n",
1208 dma_chan_name(atmel_port->chan_rx));
1209
1210 spin_lock_init(&atmel_port->lock_rx);
1211 sg_init_table(&atmel_port->sg_rx, 1);
1212 /* UART circular rx buffer is an aligned page. */
1213 BUG_ON(!PAGE_ALIGNED(ring->buf));
1214 sg_set_page(&atmel_port->sg_rx,
1215 virt_to_page(ring->buf),
1216 sizeof(struct atmel_uart_char) * ATMEL_SERIAL_RINGSIZE,
1217 offset_in_page(ring->buf));
1218 nent = dma_map_sg(port->dev,
1219 &atmel_port->sg_rx,
1220 1,
1221 DMA_FROM_DEVICE);
1222
1223 if (!nent) {
1224 dev_dbg(port->dev, "need to release resource of dma\n");
1225 goto chan_err;
1226 } else {
1227 dev_dbg(port->dev, "%s: mapped %d@%p to %pad\n", __func__,
1228 sg_dma_len(&atmel_port->sg_rx),
1229 ring->buf,
1230 &sg_dma_address(&atmel_port->sg_rx));
1231 }
1232
1233 /* Configure the slave DMA */
1234 memset(&config, 0, sizeof(config));
1235 config.direction = DMA_DEV_TO_MEM;
1236 config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1237 config.src_addr = port->mapbase + ATMEL_US_RHR;
1238 config.src_maxburst = 1;
1239
1240 ret = dmaengine_slave_config(atmel_port->chan_rx,
1241 &config);
1242 if (ret) {
1243 dev_err(port->dev, "DMA rx slave configuration failed\n");
1244 goto chan_err;
1245 }
1246 /*
1247 * Prepare a cyclic dma transfer, assign 2 descriptors,
1248 * each one is half ring buffer size
1249 */
1250 desc = dmaengine_prep_dma_cyclic(atmel_port->chan_rx,
1251 sg_dma_address(&atmel_port->sg_rx),
1252 sg_dma_len(&atmel_port->sg_rx),
1253 sg_dma_len(&atmel_port->sg_rx)/2,
1254 DMA_DEV_TO_MEM,
1255 DMA_PREP_INTERRUPT);
1256 if (!desc) {
1257 dev_err(port->dev, "Preparing DMA cyclic failed\n");
1258 goto chan_err;
1259 }
1260 desc->callback = atmel_complete_rx_dma;
1261 desc->callback_param = port;
1262 atmel_port->desc_rx = desc;
1263 atmel_port->cookie_rx = dmaengine_submit(desc);
1264
1265 return 0;
1266
1267chan_err:
1268 dev_err(port->dev, "RX channel not available, switch to pio\n");
1269 atmel_port->use_dma_rx = 0;
1270 if (atmel_port->chan_rx)
1271 atmel_release_rx_dma(port);
1272 return -EINVAL;
1273}
1274
1275static void atmel_uart_timer_callback(struct timer_list *t)
1276{
1277 struct atmel_uart_port *atmel_port = from_timer(atmel_port, t,
1278 uart_timer);
1279 struct uart_port *port = &atmel_port->uart;
1280
1281 if (!atomic_read(&atmel_port->tasklet_shutdown)) {
1282 tasklet_schedule(&atmel_port->tasklet_rx);
1283 mod_timer(&atmel_port->uart_timer,
1284 jiffies + uart_poll_timeout(port));
1285 }
1286}
1287
1288/*
1289 * receive interrupt handler.
1290 */
1291static void
1292atmel_handle_receive(struct uart_port *port, unsigned int pending)
1293{
1294 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1295
1296 if (atmel_use_pdc_rx(port)) {
1297 /*
1298 * PDC receive. Just schedule the tasklet and let it
1299 * figure out the details.
1300 *
1301 * TODO: We're not handling error flags correctly at
1302 * the moment.
1303 */
1304 if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) {
1305 atmel_uart_writel(port, ATMEL_US_IDR,
1306 (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT));
1307 atmel_tasklet_schedule(atmel_port,
1308 &atmel_port->tasklet_rx);
1309 }
1310
1311 if (pending & (ATMEL_US_RXBRK | ATMEL_US_OVRE |
1312 ATMEL_US_FRAME | ATMEL_US_PARE))
1313 atmel_pdc_rxerr(port, pending);
1314 }
1315
1316 if (atmel_use_dma_rx(port)) {
1317 if (pending & ATMEL_US_TIMEOUT) {
1318 atmel_uart_writel(port, ATMEL_US_IDR,
1319 ATMEL_US_TIMEOUT);
1320 atmel_tasklet_schedule(atmel_port,
1321 &atmel_port->tasklet_rx);
1322 }
1323 }
1324
1325 /* Interrupt receive */
1326 if (pending & ATMEL_US_RXRDY)
1327 atmel_rx_chars(port);
1328 else if (pending & ATMEL_US_RXBRK) {
1329 /*
1330 * End of break detected. If it came along with a
1331 * character, atmel_rx_chars will handle it.
1332 */
1333 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
1334 atmel_uart_writel(port, ATMEL_US_IDR, ATMEL_US_RXBRK);
1335 atmel_port->break_active = 0;
1336 }
1337}
1338
1339/*
1340 * transmit interrupt handler. (Transmit is IRQF_NODELAY safe)
1341 */
1342static void
1343atmel_handle_transmit(struct uart_port *port, unsigned int pending)
1344{
1345 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1346
1347 if (pending & atmel_port->tx_done_mask) {
1348 atmel_uart_writel(port, ATMEL_US_IDR,
1349 atmel_port->tx_done_mask);
1350
1351 /* Start RX if flag was set and FIFO is empty */
1352 if (atmel_port->hd_start_rx) {
1353 if (!(atmel_uart_readl(port, ATMEL_US_CSR)
1354 & ATMEL_US_TXEMPTY))
1355 dev_warn(port->dev, "Should start RX, but TX fifo is not empty\n");
1356
1357 atmel_port->hd_start_rx = false;
1358 atmel_start_rx(port);
1359 }
1360
1361 atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
1362 }
1363}
1364
1365/*
1366 * status flags interrupt handler.
1367 */
1368static void
1369atmel_handle_status(struct uart_port *port, unsigned int pending,
1370 unsigned int status)
1371{
1372 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1373 unsigned int status_change;
1374
1375 if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC
1376 | ATMEL_US_CTSIC)) {
1377 status_change = status ^ atmel_port->irq_status_prev;
1378 atmel_port->irq_status_prev = status;
1379
1380 if (status_change & (ATMEL_US_RI | ATMEL_US_DSR
1381 | ATMEL_US_DCD | ATMEL_US_CTS)) {
1382 /* TODO: All reads to CSR will clear these interrupts! */
1383 if (status_change & ATMEL_US_RI)
1384 port->icount.rng++;
1385 if (status_change & ATMEL_US_DSR)
1386 port->icount.dsr++;
1387 if (status_change & ATMEL_US_DCD)
1388 uart_handle_dcd_change(port, !(status & ATMEL_US_DCD));
1389 if (status_change & ATMEL_US_CTS)
1390 uart_handle_cts_change(port, !(status & ATMEL_US_CTS));
1391
1392 wake_up_interruptible(&port->state->port.delta_msr_wait);
1393 }
1394 }
1395
1396 if (pending & (ATMEL_US_NACK | ATMEL_US_ITERATION))
1397 dev_dbg(port->dev, "ISO7816 ERROR (0x%08x)\n", pending);
1398}
1399
1400/*
1401 * Interrupt handler
1402 */
1403static irqreturn_t atmel_interrupt(int irq, void *dev_id)
1404{
1405 struct uart_port *port = dev_id;
1406 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1407 unsigned int status, pending, mask, pass_counter = 0;
1408
1409 spin_lock(&atmel_port->lock_suspended);
1410
1411 do {
1412 status = atmel_uart_readl(port, ATMEL_US_CSR);
1413 mask = atmel_uart_readl(port, ATMEL_US_IMR);
1414 pending = status & mask;
1415 if (!pending)
1416 break;
1417
1418 if (atmel_port->suspended) {
1419 atmel_port->pending |= pending;
1420 atmel_port->pending_status = status;
1421 atmel_uart_writel(port, ATMEL_US_IDR, mask);
1422 pm_system_wakeup();
1423 break;
1424 }
1425
1426 atmel_handle_receive(port, pending);
1427 atmel_handle_status(port, pending, status);
1428 atmel_handle_transmit(port, pending);
1429 } while (pass_counter++ < ATMEL_ISR_PASS_LIMIT);
1430
1431 spin_unlock(&atmel_port->lock_suspended);
1432
1433 return pass_counter ? IRQ_HANDLED : IRQ_NONE;
1434}
1435
1436static void atmel_release_tx_pdc(struct uart_port *port)
1437{
1438 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1439 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1440
1441 dma_unmap_single(port->dev,
1442 pdc->dma_addr,
1443 pdc->dma_size,
1444 DMA_TO_DEVICE);
1445}
1446
1447/*
1448 * Called from tasklet with ENDTX and TXBUFE interrupts disabled.
1449 */
1450static void atmel_tx_pdc(struct uart_port *port)
1451{
1452 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1453 struct circ_buf *xmit = &port->state->xmit;
1454 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1455 int count;
1456
1457 /* nothing left to transmit? */
1458 if (atmel_uart_readl(port, ATMEL_PDC_TCR))
1459 return;
1460
1461 xmit->tail += pdc->ofs;
1462 xmit->tail &= UART_XMIT_SIZE - 1;
1463
1464 port->icount.tx += pdc->ofs;
1465 pdc->ofs = 0;
1466
1467 /* more to transmit - setup next transfer */
1468
1469 /* disable PDC transmit */
1470 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
1471
1472 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
1473 dma_sync_single_for_device(port->dev,
1474 pdc->dma_addr,
1475 pdc->dma_size,
1476 DMA_TO_DEVICE);
1477
1478 count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
1479 pdc->ofs = count;
1480
1481 atmel_uart_writel(port, ATMEL_PDC_TPR,
1482 pdc->dma_addr + xmit->tail);
1483 atmel_uart_writel(port, ATMEL_PDC_TCR, count);
1484 /* re-enable PDC transmit */
1485 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
1486 /* Enable interrupts */
1487 atmel_uart_writel(port, ATMEL_US_IER,
1488 atmel_port->tx_done_mask);
1489 } else {
1490 if (atmel_uart_is_half_duplex(port)) {
1491 /* DMA done, stop TX, start RX for RS485 */
1492 atmel_start_rx(port);
1493 }
1494 }
1495
1496 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1497 uart_write_wakeup(port);
1498}
1499
1500static int atmel_prepare_tx_pdc(struct uart_port *port)
1501{
1502 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1503 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1504 struct circ_buf *xmit = &port->state->xmit;
1505
1506 pdc->buf = xmit->buf;
1507 pdc->dma_addr = dma_map_single(port->dev,
1508 pdc->buf,
1509 UART_XMIT_SIZE,
1510 DMA_TO_DEVICE);
1511 pdc->dma_size = UART_XMIT_SIZE;
1512 pdc->ofs = 0;
1513
1514 return 0;
1515}
1516
1517static void atmel_rx_from_ring(struct uart_port *port)
1518{
1519 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1520 struct circ_buf *ring = &atmel_port->rx_ring;
1521 unsigned int flg;
1522 unsigned int status;
1523
1524 while (ring->head != ring->tail) {
1525 struct atmel_uart_char c;
1526
1527 /* Make sure c is loaded after head. */
1528 smp_rmb();
1529
1530 c = ((struct atmel_uart_char *)ring->buf)[ring->tail];
1531
1532 ring->tail = (ring->tail + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
1533
1534 port->icount.rx++;
1535 status = c.status;
1536 flg = TTY_NORMAL;
1537
1538 /*
1539 * note that the error handling code is
1540 * out of the main execution path
1541 */
1542 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
1543 | ATMEL_US_OVRE | ATMEL_US_RXBRK))) {
1544 if (status & ATMEL_US_RXBRK) {
1545 /* ignore side-effect */
1546 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
1547
1548 port->icount.brk++;
1549 if (uart_handle_break(port))
1550 continue;
1551 }
1552 if (status & ATMEL_US_PARE)
1553 port->icount.parity++;
1554 if (status & ATMEL_US_FRAME)
1555 port->icount.frame++;
1556 if (status & ATMEL_US_OVRE)
1557 port->icount.overrun++;
1558
1559 status &= port->read_status_mask;
1560
1561 if (status & ATMEL_US_RXBRK)
1562 flg = TTY_BREAK;
1563 else if (status & ATMEL_US_PARE)
1564 flg = TTY_PARITY;
1565 else if (status & ATMEL_US_FRAME)
1566 flg = TTY_FRAME;
1567 }
1568
1569
1570 if (uart_handle_sysrq_char(port, c.ch))
1571 continue;
1572
1573 uart_insert_char(port, status, ATMEL_US_OVRE, c.ch, flg);
1574 }
1575
1576 /*
1577 * Drop the lock here since it might end up calling
1578 * uart_start(), which takes the lock.
1579 */
1580 spin_unlock(&port->lock);
1581 tty_flip_buffer_push(&port->state->port);
1582 spin_lock(&port->lock);
1583}
1584
1585static void atmel_release_rx_pdc(struct uart_port *port)
1586{
1587 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1588 int i;
1589
1590 for (i = 0; i < 2; i++) {
1591 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1592
1593 dma_unmap_single(port->dev,
1594 pdc->dma_addr,
1595 pdc->dma_size,
1596 DMA_FROM_DEVICE);
1597 kfree(pdc->buf);
1598 }
1599}
1600
1601static void atmel_rx_from_pdc(struct uart_port *port)
1602{
1603 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1604 struct tty_port *tport = &port->state->port;
1605 struct atmel_dma_buffer *pdc;
1606 int rx_idx = atmel_port->pdc_rx_idx;
1607 unsigned int head;
1608 unsigned int tail;
1609 unsigned int count;
1610
1611 do {
1612 /* Reset the UART timeout early so that we don't miss one */
1613 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1614
1615 pdc = &atmel_port->pdc_rx[rx_idx];
1616 head = atmel_uart_readl(port, ATMEL_PDC_RPR) - pdc->dma_addr;
1617 tail = pdc->ofs;
1618
1619 /* If the PDC has switched buffers, RPR won't contain
1620 * any address within the current buffer. Since head
1621 * is unsigned, we just need a one-way comparison to
1622 * find out.
1623 *
1624 * In this case, we just need to consume the entire
1625 * buffer and resubmit it for DMA. This will clear the
1626 * ENDRX bit as well, so that we can safely re-enable
1627 * all interrupts below.
1628 */
1629 head = min(head, pdc->dma_size);
1630
1631 if (likely(head != tail)) {
1632 dma_sync_single_for_cpu(port->dev, pdc->dma_addr,
1633 pdc->dma_size, DMA_FROM_DEVICE);
1634
1635 /*
1636 * head will only wrap around when we recycle
1637 * the DMA buffer, and when that happens, we
1638 * explicitly set tail to 0. So head will
1639 * always be greater than tail.
1640 */
1641 count = head - tail;
1642
1643 tty_insert_flip_string(tport, pdc->buf + pdc->ofs,
1644 count);
1645
1646 dma_sync_single_for_device(port->dev, pdc->dma_addr,
1647 pdc->dma_size, DMA_FROM_DEVICE);
1648
1649 port->icount.rx += count;
1650 pdc->ofs = head;
1651 }
1652
1653 /*
1654 * If the current buffer is full, we need to check if
1655 * the next one contains any additional data.
1656 */
1657 if (head >= pdc->dma_size) {
1658 pdc->ofs = 0;
1659 atmel_uart_writel(port, ATMEL_PDC_RNPR, pdc->dma_addr);
1660 atmel_uart_writel(port, ATMEL_PDC_RNCR, pdc->dma_size);
1661
1662 rx_idx = !rx_idx;
1663 atmel_port->pdc_rx_idx = rx_idx;
1664 }
1665 } while (head >= pdc->dma_size);
1666
1667 /*
1668 * Drop the lock here since it might end up calling
1669 * uart_start(), which takes the lock.
1670 */
1671 spin_unlock(&port->lock);
1672 tty_flip_buffer_push(tport);
1673 spin_lock(&port->lock);
1674
1675 atmel_uart_writel(port, ATMEL_US_IER,
1676 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1677}
1678
1679static int atmel_prepare_rx_pdc(struct uart_port *port)
1680{
1681 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1682 int i;
1683
1684 for (i = 0; i < 2; i++) {
1685 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1686
1687 pdc->buf = kmalloc(PDC_BUFFER_SIZE, GFP_KERNEL);
1688 if (pdc->buf == NULL) {
1689 if (i != 0) {
1690 dma_unmap_single(port->dev,
1691 atmel_port->pdc_rx[0].dma_addr,
1692 PDC_BUFFER_SIZE,
1693 DMA_FROM_DEVICE);
1694 kfree(atmel_port->pdc_rx[0].buf);
1695 }
1696 atmel_port->use_pdc_rx = 0;
1697 return -ENOMEM;
1698 }
1699 pdc->dma_addr = dma_map_single(port->dev,
1700 pdc->buf,
1701 PDC_BUFFER_SIZE,
1702 DMA_FROM_DEVICE);
1703 pdc->dma_size = PDC_BUFFER_SIZE;
1704 pdc->ofs = 0;
1705 }
1706
1707 atmel_port->pdc_rx_idx = 0;
1708
1709 atmel_uart_writel(port, ATMEL_PDC_RPR, atmel_port->pdc_rx[0].dma_addr);
1710 atmel_uart_writel(port, ATMEL_PDC_RCR, PDC_BUFFER_SIZE);
1711
1712 atmel_uart_writel(port, ATMEL_PDC_RNPR,
1713 atmel_port->pdc_rx[1].dma_addr);
1714 atmel_uart_writel(port, ATMEL_PDC_RNCR, PDC_BUFFER_SIZE);
1715
1716 return 0;
1717}
1718
1719/*
1720 * tasklet handling tty stuff outside the interrupt handler.
1721 */
1722static void atmel_tasklet_rx_func(unsigned long data)
1723{
1724 struct uart_port *port = (struct uart_port *)data;
1725 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1726
1727 /* The interrupt handler does not take the lock */
1728 spin_lock(&port->lock);
1729 atmel_port->schedule_rx(port);
1730 spin_unlock(&port->lock);
1731}
1732
1733static void atmel_tasklet_tx_func(unsigned long data)
1734{
1735 struct uart_port *port = (struct uart_port *)data;
1736 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1737
1738 /* The interrupt handler does not take the lock */
1739 spin_lock(&port->lock);
1740 atmel_port->schedule_tx(port);
1741 spin_unlock(&port->lock);
1742}
1743
1744static void atmel_init_property(struct atmel_uart_port *atmel_port,
1745 struct platform_device *pdev)
1746{
1747 struct device_node *np = pdev->dev.of_node;
1748
1749 /* DMA/PDC usage specification */
1750 if (of_property_read_bool(np, "atmel,use-dma-rx")) {
1751 if (of_property_read_bool(np, "dmas")) {
1752 atmel_port->use_dma_rx = true;
1753 atmel_port->use_pdc_rx = false;
1754 } else {
1755 atmel_port->use_dma_rx = false;
1756 atmel_port->use_pdc_rx = true;
1757 }
1758 } else {
1759 atmel_port->use_dma_rx = false;
1760 atmel_port->use_pdc_rx = false;
1761 }
1762
1763 if (of_property_read_bool(np, "atmel,use-dma-tx")) {
1764 if (of_property_read_bool(np, "dmas")) {
1765 atmel_port->use_dma_tx = true;
1766 atmel_port->use_pdc_tx = false;
1767 } else {
1768 atmel_port->use_dma_tx = false;
1769 atmel_port->use_pdc_tx = true;
1770 }
1771 } else {
1772 atmel_port->use_dma_tx = false;
1773 atmel_port->use_pdc_tx = false;
1774 }
1775}
1776
1777static void atmel_set_ops(struct uart_port *port)
1778{
1779 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1780
1781 if (atmel_use_dma_rx(port)) {
1782 atmel_port->prepare_rx = &atmel_prepare_rx_dma;
1783 atmel_port->schedule_rx = &atmel_rx_from_dma;
1784 atmel_port->release_rx = &atmel_release_rx_dma;
1785 } else if (atmel_use_pdc_rx(port)) {
1786 atmel_port->prepare_rx = &atmel_prepare_rx_pdc;
1787 atmel_port->schedule_rx = &atmel_rx_from_pdc;
1788 atmel_port->release_rx = &atmel_release_rx_pdc;
1789 } else {
1790 atmel_port->prepare_rx = NULL;
1791 atmel_port->schedule_rx = &atmel_rx_from_ring;
1792 atmel_port->release_rx = NULL;
1793 }
1794
1795 if (atmel_use_dma_tx(port)) {
1796 atmel_port->prepare_tx = &atmel_prepare_tx_dma;
1797 atmel_port->schedule_tx = &atmel_tx_dma;
1798 atmel_port->release_tx = &atmel_release_tx_dma;
1799 } else if (atmel_use_pdc_tx(port)) {
1800 atmel_port->prepare_tx = &atmel_prepare_tx_pdc;
1801 atmel_port->schedule_tx = &atmel_tx_pdc;
1802 atmel_port->release_tx = &atmel_release_tx_pdc;
1803 } else {
1804 atmel_port->prepare_tx = NULL;
1805 atmel_port->schedule_tx = &atmel_tx_chars;
1806 atmel_port->release_tx = NULL;
1807 }
1808}
1809
1810/*
1811 * Get ip name usart or uart
1812 */
1813static void atmel_get_ip_name(struct uart_port *port)
1814{
1815 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1816 int name = atmel_uart_readl(port, ATMEL_US_NAME);
1817 u32 version;
1818 u32 usart, dbgu_uart, new_uart;
1819 /* ASCII decoding for IP version */
1820 usart = 0x55534152; /* USAR(T) */
1821 dbgu_uart = 0x44424755; /* DBGU */
1822 new_uart = 0x55415254; /* UART */
1823
1824 /*
1825 * Only USART devices from at91sam9260 SOC implement fractional
1826 * baudrate. It is available for all asynchronous modes, with the
1827 * following restriction: the sampling clock's duty cycle is not
1828 * constant.
1829 */
1830 atmel_port->has_frac_baudrate = false;
1831 atmel_port->has_hw_timer = false;
1832
1833 if (name == new_uart) {
1834 dev_dbg(port->dev, "Uart with hw timer");
1835 atmel_port->has_hw_timer = true;
1836 atmel_port->rtor = ATMEL_UA_RTOR;
1837 } else if (name == usart) {
1838 dev_dbg(port->dev, "Usart\n");
1839 atmel_port->has_frac_baudrate = true;
1840 atmel_port->has_hw_timer = true;
1841 atmel_port->rtor = ATMEL_US_RTOR;
1842 version = atmel_uart_readl(port, ATMEL_US_VERSION);
1843 switch (version) {
1844 case 0x814: /* sama5d2 */
1845 /* fall through */
1846 case 0x701: /* sama5d4 */
1847 atmel_port->fidi_min = 3;
1848 atmel_port->fidi_max = 65535;
1849 break;
1850 case 0x502: /* sam9x5, sama5d3 */
1851 atmel_port->fidi_min = 3;
1852 atmel_port->fidi_max = 2047;
1853 break;
1854 default:
1855 atmel_port->fidi_min = 1;
1856 atmel_port->fidi_max = 2047;
1857 }
1858 } else if (name == dbgu_uart) {
1859 dev_dbg(port->dev, "Dbgu or uart without hw timer\n");
1860 } else {
1861 /* fallback for older SoCs: use version field */
1862 version = atmel_uart_readl(port, ATMEL_US_VERSION);
1863 switch (version) {
1864 case 0x302:
1865 case 0x10213:
1866 case 0x10302:
1867 dev_dbg(port->dev, "This version is usart\n");
1868 atmel_port->has_frac_baudrate = true;
1869 atmel_port->has_hw_timer = true;
1870 atmel_port->rtor = ATMEL_US_RTOR;
1871 break;
1872 case 0x203:
1873 case 0x10202:
1874 dev_dbg(port->dev, "This version is uart\n");
1875 break;
1876 default:
1877 dev_err(port->dev, "Not supported ip name nor version, set to uart\n");
1878 }
1879 }
1880}
1881
1882/*
1883 * Perform initialization and enable port for reception
1884 */
1885static int atmel_startup(struct uart_port *port)
1886{
1887 struct platform_device *pdev = to_platform_device(port->dev);
1888 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1889 int retval;
1890
1891 /*
1892 * Ensure that no interrupts are enabled otherwise when
1893 * request_irq() is called we could get stuck trying to
1894 * handle an unexpected interrupt
1895 */
1896 atmel_uart_writel(port, ATMEL_US_IDR, -1);
1897 atmel_port->ms_irq_enabled = false;
1898
1899 /*
1900 * Allocate the IRQ
1901 */
1902 retval = request_irq(port->irq, atmel_interrupt,
1903 IRQF_SHARED | IRQF_COND_SUSPEND,
1904 dev_name(&pdev->dev), port);
1905 if (retval) {
1906 dev_err(port->dev, "atmel_startup - Can't get irq\n");
1907 return retval;
1908 }
1909
1910 atomic_set(&atmel_port->tasklet_shutdown, 0);
1911 tasklet_init(&atmel_port->tasklet_rx, atmel_tasklet_rx_func,
1912 (unsigned long)port);
1913 tasklet_init(&atmel_port->tasklet_tx, atmel_tasklet_tx_func,
1914 (unsigned long)port);
1915
1916 /*
1917 * Initialize DMA (if necessary)
1918 */
1919 atmel_init_property(atmel_port, pdev);
1920 atmel_set_ops(port);
1921
1922 if (atmel_port->prepare_rx) {
1923 retval = atmel_port->prepare_rx(port);
1924 if (retval < 0)
1925 atmel_set_ops(port);
1926 }
1927
1928 if (atmel_port->prepare_tx) {
1929 retval = atmel_port->prepare_tx(port);
1930 if (retval < 0)
1931 atmel_set_ops(port);
1932 }
1933
1934 /*
1935 * Enable FIFO when available
1936 */
1937 if (atmel_port->fifo_size) {
1938 unsigned int txrdym = ATMEL_US_ONE_DATA;
1939 unsigned int rxrdym = ATMEL_US_ONE_DATA;
1940 unsigned int fmr;
1941
1942 atmel_uart_writel(port, ATMEL_US_CR,
1943 ATMEL_US_FIFOEN |
1944 ATMEL_US_RXFCLR |
1945 ATMEL_US_TXFLCLR);
1946
1947 if (atmel_use_dma_tx(port))
1948 txrdym = ATMEL_US_FOUR_DATA;
1949
1950 fmr = ATMEL_US_TXRDYM(txrdym) | ATMEL_US_RXRDYM(rxrdym);
1951 if (atmel_port->rts_high &&
1952 atmel_port->rts_low)
1953 fmr |= ATMEL_US_FRTSC |
1954 ATMEL_US_RXFTHRES(atmel_port->rts_high) |
1955 ATMEL_US_RXFTHRES2(atmel_port->rts_low);
1956
1957 atmel_uart_writel(port, ATMEL_US_FMR, fmr);
1958 }
1959
1960 /* Save current CSR for comparison in atmel_tasklet_func() */
1961 atmel_port->irq_status_prev = atmel_uart_readl(port, ATMEL_US_CSR);
1962
1963 /*
1964 * Finally, enable the serial port
1965 */
1966 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
1967 /* enable xmit & rcvr */
1968 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
1969 atmel_port->tx_stopped = false;
1970
1971 timer_setup(&atmel_port->uart_timer, atmel_uart_timer_callback, 0);
1972
1973 if (atmel_use_pdc_rx(port)) {
1974 /* set UART timeout */
1975 if (!atmel_port->has_hw_timer) {
1976 mod_timer(&atmel_port->uart_timer,
1977 jiffies + uart_poll_timeout(port));
1978 /* set USART timeout */
1979 } else {
1980 atmel_uart_writel(port, atmel_port->rtor,
1981 PDC_RX_TIMEOUT);
1982 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1983
1984 atmel_uart_writel(port, ATMEL_US_IER,
1985 ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1986 }
1987 /* enable PDC controller */
1988 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
1989 } else if (atmel_use_dma_rx(port)) {
1990 /* set UART timeout */
1991 if (!atmel_port->has_hw_timer) {
1992 mod_timer(&atmel_port->uart_timer,
1993 jiffies + uart_poll_timeout(port));
1994 /* set USART timeout */
1995 } else {
1996 atmel_uart_writel(port, atmel_port->rtor,
1997 PDC_RX_TIMEOUT);
1998 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_STTTO);
1999
2000 atmel_uart_writel(port, ATMEL_US_IER,
2001 ATMEL_US_TIMEOUT);
2002 }
2003 } else {
2004 /* enable receive only */
2005 atmel_uart_writel(port, ATMEL_US_IER, ATMEL_US_RXRDY);
2006 }
2007
2008 return 0;
2009}
2010
2011/*
2012 * Flush any TX data submitted for DMA. Called when the TX circular
2013 * buffer is reset.
2014 */
2015static void atmel_flush_buffer(struct uart_port *port)
2016{
2017 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2018
2019 if (atmel_use_pdc_tx(port)) {
2020 atmel_uart_writel(port, ATMEL_PDC_TCR, 0);
2021 atmel_port->pdc_tx.ofs = 0;
2022 }
2023 /*
2024 * in uart_flush_buffer(), the xmit circular buffer has just
2025 * been cleared, so we have to reset tx_len accordingly.
2026 */
2027 atmel_port->tx_len = 0;
2028}
2029
2030/*
2031 * Disable the port
2032 */
2033static void atmel_shutdown(struct uart_port *port)
2034{
2035 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2036
2037 /* Disable modem control lines interrupts */
2038 atmel_disable_ms(port);
2039
2040 /* Disable interrupts at device level */
2041 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2042
2043 /* Prevent spurious interrupts from scheduling the tasklet */
2044 atomic_inc(&atmel_port->tasklet_shutdown);
2045
2046 /*
2047 * Prevent any tasklets being scheduled during
2048 * cleanup
2049 */
2050 del_timer_sync(&atmel_port->uart_timer);
2051
2052 /* Make sure that no interrupt is on the fly */
2053 synchronize_irq(port->irq);
2054
2055 /*
2056 * Clear out any scheduled tasklets before
2057 * we destroy the buffers
2058 */
2059 tasklet_kill(&atmel_port->tasklet_rx);
2060 tasklet_kill(&atmel_port->tasklet_tx);
2061
2062 /*
2063 * Ensure everything is stopped and
2064 * disable port and break condition.
2065 */
2066 atmel_stop_rx(port);
2067 atmel_stop_tx(port);
2068
2069 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA);
2070
2071 /*
2072 * Shut-down the DMA.
2073 */
2074 if (atmel_port->release_rx)
2075 atmel_port->release_rx(port);
2076 if (atmel_port->release_tx)
2077 atmel_port->release_tx(port);
2078
2079 /*
2080 * Reset ring buffer pointers
2081 */
2082 atmel_port->rx_ring.head = 0;
2083 atmel_port->rx_ring.tail = 0;
2084
2085 /*
2086 * Free the interrupts
2087 */
2088 free_irq(port->irq, port);
2089
2090 atmel_flush_buffer(port);
2091}
2092
2093/*
2094 * Power / Clock management.
2095 */
2096static void atmel_serial_pm(struct uart_port *port, unsigned int state,
2097 unsigned int oldstate)
2098{
2099 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2100
2101 switch (state) {
2102 case 0:
2103 /*
2104 * Enable the peripheral clock for this serial port.
2105 * This is called on uart_open() or a resume event.
2106 */
2107 clk_prepare_enable(atmel_port->clk);
2108
2109 /* re-enable interrupts if we disabled some on suspend */
2110 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->backup_imr);
2111 break;
2112 case 3:
2113 /* Back up the interrupt mask and disable all interrupts */
2114 atmel_port->backup_imr = atmel_uart_readl(port, ATMEL_US_IMR);
2115 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2116
2117 /*
2118 * Disable the peripheral clock for this serial port.
2119 * This is called on uart_close() or a suspend event.
2120 */
2121 clk_disable_unprepare(atmel_port->clk);
2122 break;
2123 default:
2124 dev_err(port->dev, "atmel_serial: unknown pm %d\n", state);
2125 }
2126}
2127
2128/*
2129 * Change the port parameters
2130 */
2131static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
2132 struct ktermios *old)
2133{
2134 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2135 unsigned long flags;
2136 unsigned int old_mode, mode, imr, quot, baud, div, cd, fp = 0;
2137
2138 /* save the current mode register */
2139 mode = old_mode = atmel_uart_readl(port, ATMEL_US_MR);
2140
2141 /* reset the mode, clock divisor, parity, stop bits and data size */
2142 mode &= ~(ATMEL_US_USCLKS | ATMEL_US_CHRL | ATMEL_US_NBSTOP |
2143 ATMEL_US_PAR | ATMEL_US_USMODE);
2144
2145 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
2146
2147 /* byte size */
2148 switch (termios->c_cflag & CSIZE) {
2149 case CS5:
2150 mode |= ATMEL_US_CHRL_5;
2151 break;
2152 case CS6:
2153 mode |= ATMEL_US_CHRL_6;
2154 break;
2155 case CS7:
2156 mode |= ATMEL_US_CHRL_7;
2157 break;
2158 default:
2159 mode |= ATMEL_US_CHRL_8;
2160 break;
2161 }
2162
2163 /* stop bits */
2164 if (termios->c_cflag & CSTOPB)
2165 mode |= ATMEL_US_NBSTOP_2;
2166
2167 /* parity */
2168 if (termios->c_cflag & PARENB) {
2169 /* Mark or Space parity */
2170 if (termios->c_cflag & CMSPAR) {
2171 if (termios->c_cflag & PARODD)
2172 mode |= ATMEL_US_PAR_MARK;
2173 else
2174 mode |= ATMEL_US_PAR_SPACE;
2175 } else if (termios->c_cflag & PARODD)
2176 mode |= ATMEL_US_PAR_ODD;
2177 else
2178 mode |= ATMEL_US_PAR_EVEN;
2179 } else
2180 mode |= ATMEL_US_PAR_NONE;
2181
2182 spin_lock_irqsave(&port->lock, flags);
2183
2184 port->read_status_mask = ATMEL_US_OVRE;
2185 if (termios->c_iflag & INPCK)
2186 port->read_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
2187 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
2188 port->read_status_mask |= ATMEL_US_RXBRK;
2189
2190 if (atmel_use_pdc_rx(port))
2191 /* need to enable error interrupts */
2192 atmel_uart_writel(port, ATMEL_US_IER, port->read_status_mask);
2193
2194 /*
2195 * Characters to ignore
2196 */
2197 port->ignore_status_mask = 0;
2198 if (termios->c_iflag & IGNPAR)
2199 port->ignore_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
2200 if (termios->c_iflag & IGNBRK) {
2201 port->ignore_status_mask |= ATMEL_US_RXBRK;
2202 /*
2203 * If we're ignoring parity and break indicators,
2204 * ignore overruns too (for real raw support).
2205 */
2206 if (termios->c_iflag & IGNPAR)
2207 port->ignore_status_mask |= ATMEL_US_OVRE;
2208 }
2209 /* TODO: Ignore all characters if CREAD is set.*/
2210
2211 /* update the per-port timeout */
2212 uart_update_timeout(port, termios->c_cflag, baud);
2213
2214 /*
2215 * save/disable interrupts. The tty layer will ensure that the
2216 * transmitter is empty if requested by the caller, so there's
2217 * no need to wait for it here.
2218 */
2219 imr = atmel_uart_readl(port, ATMEL_US_IMR);
2220 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2221
2222 /* disable receiver and transmitter */
2223 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
2224 atmel_port->tx_stopped = true;
2225
2226 /* mode */
2227 if (port->rs485.flags & SER_RS485_ENABLED) {
2228 atmel_uart_writel(port, ATMEL_US_TTGR,
2229 port->rs485.delay_rts_after_send);
2230 mode |= ATMEL_US_USMODE_RS485;
2231 } else if (port->iso7816.flags & SER_ISO7816_ENABLED) {
2232 atmel_uart_writel(port, ATMEL_US_TTGR, port->iso7816.tg);
2233 /* select mck clock, and output */
2234 mode |= ATMEL_US_USCLKS_MCK | ATMEL_US_CLKO;
2235 /* set max iterations */
2236 mode |= ATMEL_US_MAX_ITER(3);
2237 if ((port->iso7816.flags & SER_ISO7816_T_PARAM)
2238 == SER_ISO7816_T(0))
2239 mode |= ATMEL_US_USMODE_ISO7816_T0;
2240 else
2241 mode |= ATMEL_US_USMODE_ISO7816_T1;
2242 } else if (termios->c_cflag & CRTSCTS) {
2243 /* RS232 with hardware handshake (RTS/CTS) */
2244 if (atmel_use_fifo(port) &&
2245 !mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS)) {
2246 /*
2247 * with ATMEL_US_USMODE_HWHS set, the controller will
2248 * be able to drive the RTS pin high/low when the RX
2249 * FIFO is above RXFTHRES/below RXFTHRES2.
2250 * It will also disable the transmitter when the CTS
2251 * pin is high.
2252 * This mode is not activated if CTS pin is a GPIO
2253 * because in this case, the transmitter is always
2254 * disabled (there must be an internal pull-up
2255 * responsible for this behaviour).
2256 * If the RTS pin is a GPIO, the controller won't be
2257 * able to drive it according to the FIFO thresholds,
2258 * but it will be handled by the driver.
2259 */
2260 mode |= ATMEL_US_USMODE_HWHS;
2261 } else {
2262 /*
2263 * For platforms without FIFO, the flow control is
2264 * handled by the driver.
2265 */
2266 mode |= ATMEL_US_USMODE_NORMAL;
2267 }
2268 } else {
2269 /* RS232 without hadware handshake */
2270 mode |= ATMEL_US_USMODE_NORMAL;
2271 }
2272
2273 /* set the mode, clock divisor, parity, stop bits and data size */
2274 atmel_uart_writel(port, ATMEL_US_MR, mode);
2275
2276 /*
2277 * when switching the mode, set the RTS line state according to the
2278 * new mode, otherwise keep the former state
2279 */
2280 if ((old_mode & ATMEL_US_USMODE) != (mode & ATMEL_US_USMODE)) {
2281 unsigned int rts_state;
2282
2283 if ((mode & ATMEL_US_USMODE) == ATMEL_US_USMODE_HWHS) {
2284 /* let the hardware control the RTS line */
2285 rts_state = ATMEL_US_RTSDIS;
2286 } else {
2287 /* force RTS line to low level */
2288 rts_state = ATMEL_US_RTSEN;
2289 }
2290
2291 atmel_uart_writel(port, ATMEL_US_CR, rts_state);
2292 }
2293
2294 /*
2295 * Set the baud rate:
2296 * Fractional baudrate allows to setup output frequency more
2297 * accurately. This feature is enabled only when using normal mode.
2298 * baudrate = selected clock / (8 * (2 - OVER) * (CD + FP / 8))
2299 * Currently, OVER is always set to 0 so we get
2300 * baudrate = selected clock / (16 * (CD + FP / 8))
2301 * then
2302 * 8 CD + FP = selected clock / (2 * baudrate)
2303 */
2304 if (atmel_port->has_frac_baudrate) {
2305 div = DIV_ROUND_CLOSEST(port->uartclk, baud * 2);
2306 cd = div >> 3;
2307 fp = div & ATMEL_US_FP_MASK;
2308 } else {
2309 cd = uart_get_divisor(port, baud);
2310 }
2311
2312 if (cd > 65535) { /* BRGR is 16-bit, so switch to slower clock */
2313 cd /= 8;
2314 mode |= ATMEL_US_USCLKS_MCK_DIV8;
2315 }
2316 quot = cd | fp << ATMEL_US_FP_OFFSET;
2317
2318 if (!(port->iso7816.flags & SER_ISO7816_ENABLED))
2319 atmel_uart_writel(port, ATMEL_US_BRGR, quot);
2320 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
2321 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
2322 atmel_port->tx_stopped = false;
2323
2324 /* restore interrupts */
2325 atmel_uart_writel(port, ATMEL_US_IER, imr);
2326
2327 /* CTS flow-control and modem-status interrupts */
2328 if (UART_ENABLE_MS(port, termios->c_cflag))
2329 atmel_enable_ms(port);
2330 else
2331 atmel_disable_ms(port);
2332
2333 spin_unlock_irqrestore(&port->lock, flags);
2334}
2335
2336static void atmel_set_ldisc(struct uart_port *port, struct ktermios *termios)
2337{
2338 if (termios->c_line == N_PPS) {
2339 port->flags |= UPF_HARDPPS_CD;
2340 spin_lock_irq(&port->lock);
2341 atmel_enable_ms(port);
2342 spin_unlock_irq(&port->lock);
2343 } else {
2344 port->flags &= ~UPF_HARDPPS_CD;
2345 if (!UART_ENABLE_MS(port, termios->c_cflag)) {
2346 spin_lock_irq(&port->lock);
2347 atmel_disable_ms(port);
2348 spin_unlock_irq(&port->lock);
2349 }
2350 }
2351}
2352
2353/*
2354 * Return string describing the specified port
2355 */
2356static const char *atmel_type(struct uart_port *port)
2357{
2358 return (port->type == PORT_ATMEL) ? "ATMEL_SERIAL" : NULL;
2359}
2360
2361/*
2362 * Release the memory region(s) being used by 'port'.
2363 */
2364static void atmel_release_port(struct uart_port *port)
2365{
2366 struct platform_device *mpdev = to_platform_device(port->dev->parent);
2367 int size = resource_size(mpdev->resource);
2368
2369 release_mem_region(port->mapbase, size);
2370
2371 if (port->flags & UPF_IOREMAP) {
2372 iounmap(port->membase);
2373 port->membase = NULL;
2374 }
2375}
2376
2377/*
2378 * Request the memory region(s) being used by 'port'.
2379 */
2380static int atmel_request_port(struct uart_port *port)
2381{
2382 struct platform_device *mpdev = to_platform_device(port->dev->parent);
2383 int size = resource_size(mpdev->resource);
2384
2385 if (!request_mem_region(port->mapbase, size, "atmel_serial"))
2386 return -EBUSY;
2387
2388 if (port->flags & UPF_IOREMAP) {
2389 port->membase = ioremap(port->mapbase, size);
2390 if (port->membase == NULL) {
2391 release_mem_region(port->mapbase, size);
2392 return -ENOMEM;
2393 }
2394 }
2395
2396 return 0;
2397}
2398
2399/*
2400 * Configure/autoconfigure the port.
2401 */
2402static void atmel_config_port(struct uart_port *port, int flags)
2403{
2404 if (flags & UART_CONFIG_TYPE) {
2405 port->type = PORT_ATMEL;
2406 atmel_request_port(port);
2407 }
2408}
2409
2410/*
2411 * Verify the new serial_struct (for TIOCSSERIAL).
2412 */
2413static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser)
2414{
2415 int ret = 0;
2416 if (ser->type != PORT_UNKNOWN && ser->type != PORT_ATMEL)
2417 ret = -EINVAL;
2418 if (port->irq != ser->irq)
2419 ret = -EINVAL;
2420 if (ser->io_type != SERIAL_IO_MEM)
2421 ret = -EINVAL;
2422 if (port->uartclk / 16 != ser->baud_base)
2423 ret = -EINVAL;
2424 if (port->mapbase != (unsigned long)ser->iomem_base)
2425 ret = -EINVAL;
2426 if (port->iobase != ser->port)
2427 ret = -EINVAL;
2428 if (ser->hub6 != 0)
2429 ret = -EINVAL;
2430 return ret;
2431}
2432
2433#ifdef CONFIG_CONSOLE_POLL
2434static int atmel_poll_get_char(struct uart_port *port)
2435{
2436 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_RXRDY))
2437 cpu_relax();
2438
2439 return atmel_uart_read_char(port);
2440}
2441
2442static void atmel_poll_put_char(struct uart_port *port, unsigned char ch)
2443{
2444 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
2445 cpu_relax();
2446
2447 atmel_uart_write_char(port, ch);
2448}
2449#endif
2450
2451static const struct uart_ops atmel_pops = {
2452 .tx_empty = atmel_tx_empty,
2453 .set_mctrl = atmel_set_mctrl,
2454 .get_mctrl = atmel_get_mctrl,
2455 .stop_tx = atmel_stop_tx,
2456 .start_tx = atmel_start_tx,
2457 .stop_rx = atmel_stop_rx,
2458 .enable_ms = atmel_enable_ms,
2459 .break_ctl = atmel_break_ctl,
2460 .startup = atmel_startup,
2461 .shutdown = atmel_shutdown,
2462 .flush_buffer = atmel_flush_buffer,
2463 .set_termios = atmel_set_termios,
2464 .set_ldisc = atmel_set_ldisc,
2465 .type = atmel_type,
2466 .release_port = atmel_release_port,
2467 .request_port = atmel_request_port,
2468 .config_port = atmel_config_port,
2469 .verify_port = atmel_verify_port,
2470 .pm = atmel_serial_pm,
2471#ifdef CONFIG_CONSOLE_POLL
2472 .poll_get_char = atmel_poll_get_char,
2473 .poll_put_char = atmel_poll_put_char,
2474#endif
2475};
2476
2477/*
2478 * Configure the port from the platform device resource info.
2479 */
2480static int atmel_init_port(struct atmel_uart_port *atmel_port,
2481 struct platform_device *pdev)
2482{
2483 int ret;
2484 struct uart_port *port = &atmel_port->uart;
2485 struct platform_device *mpdev = to_platform_device(pdev->dev.parent);
2486
2487 atmel_init_property(atmel_port, pdev);
2488 atmel_set_ops(port);
2489
2490 uart_get_rs485_mode(&mpdev->dev, &port->rs485);
2491
2492 port->iotype = UPIO_MEM;
2493 port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
2494 port->ops = &atmel_pops;
2495 port->fifosize = 1;
2496 port->dev = &pdev->dev;
2497 port->mapbase = mpdev->resource[0].start;
2498 port->irq = mpdev->resource[1].start;
2499 port->rs485_config = atmel_config_rs485;
2500 port->iso7816_config = atmel_config_iso7816;
2501 port->membase = NULL;
2502
2503 memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
2504
2505 /* for console, the clock could already be configured */
2506 if (!atmel_port->clk) {
2507 atmel_port->clk = clk_get(&mpdev->dev, "usart");
2508 if (IS_ERR(atmel_port->clk)) {
2509 ret = PTR_ERR(atmel_port->clk);
2510 atmel_port->clk = NULL;
2511 return ret;
2512 }
2513 ret = clk_prepare_enable(atmel_port->clk);
2514 if (ret) {
2515 clk_put(atmel_port->clk);
2516 atmel_port->clk = NULL;
2517 return ret;
2518 }
2519 port->uartclk = clk_get_rate(atmel_port->clk);
2520 clk_disable_unprepare(atmel_port->clk);
2521 /* only enable clock when USART is in use */
2522 }
2523
2524 /*
2525 * Use TXEMPTY for interrupt when rs485 or ISO7816 else TXRDY or
2526 * ENDTX|TXBUFE
2527 */
2528 if (port->rs485.flags & SER_RS485_ENABLED ||
2529 port->iso7816.flags & SER_ISO7816_ENABLED)
2530 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
2531 else if (atmel_use_pdc_tx(port)) {
2532 port->fifosize = PDC_BUFFER_SIZE;
2533 atmel_port->tx_done_mask = ATMEL_US_ENDTX | ATMEL_US_TXBUFE;
2534 } else {
2535 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
2536 }
2537
2538 return 0;
2539}
2540
2541#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
2542static void atmel_console_putchar(struct uart_port *port, int ch)
2543{
2544 while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
2545 cpu_relax();
2546 atmel_uart_write_char(port, ch);
2547}
2548
2549/*
2550 * Interrupts are disabled on entering
2551 */
2552static void atmel_console_write(struct console *co, const char *s, u_int count)
2553{
2554 struct uart_port *port = &atmel_ports[co->index].uart;
2555 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2556 unsigned int status, imr;
2557 unsigned int pdc_tx;
2558
2559 /*
2560 * First, save IMR and then disable interrupts
2561 */
2562 imr = atmel_uart_readl(port, ATMEL_US_IMR);
2563 atmel_uart_writel(port, ATMEL_US_IDR,
2564 ATMEL_US_RXRDY | atmel_port->tx_done_mask);
2565
2566 /* Store PDC transmit status and disable it */
2567 pdc_tx = atmel_uart_readl(port, ATMEL_PDC_PTSR) & ATMEL_PDC_TXTEN;
2568 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS);
2569
2570 /* Make sure that tx path is actually able to send characters */
2571 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN);
2572 atmel_port->tx_stopped = false;
2573
2574 uart_console_write(port, s, count, atmel_console_putchar);
2575
2576 /*
2577 * Finally, wait for transmitter to become empty
2578 * and restore IMR
2579 */
2580 do {
2581 status = atmel_uart_readl(port, ATMEL_US_CSR);
2582 } while (!(status & ATMEL_US_TXRDY));
2583
2584 /* Restore PDC transmit status */
2585 if (pdc_tx)
2586 atmel_uart_writel(port, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
2587
2588 /* set interrupts back the way they were */
2589 atmel_uart_writel(port, ATMEL_US_IER, imr);
2590}
2591
2592/*
2593 * If the port was already initialised (eg, by a boot loader),
2594 * try to determine the current setup.
2595 */
2596static void __init atmel_console_get_options(struct uart_port *port, int *baud,
2597 int *parity, int *bits)
2598{
2599 unsigned int mr, quot;
2600
2601 /*
2602 * If the baud rate generator isn't running, the port wasn't
2603 * initialized by the boot loader.
2604 */
2605 quot = atmel_uart_readl(port, ATMEL_US_BRGR) & ATMEL_US_CD;
2606 if (!quot)
2607 return;
2608
2609 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_CHRL;
2610 if (mr == ATMEL_US_CHRL_8)
2611 *bits = 8;
2612 else
2613 *bits = 7;
2614
2615 mr = atmel_uart_readl(port, ATMEL_US_MR) & ATMEL_US_PAR;
2616 if (mr == ATMEL_US_PAR_EVEN)
2617 *parity = 'e';
2618 else if (mr == ATMEL_US_PAR_ODD)
2619 *parity = 'o';
2620
2621 /*
2622 * The serial core only rounds down when matching this to a
2623 * supported baud rate. Make sure we don't end up slightly
2624 * lower than one of those, as it would make us fall through
2625 * to a much lower baud rate than we really want.
2626 */
2627 *baud = port->uartclk / (16 * (quot - 1));
2628}
2629
2630static int __init atmel_console_setup(struct console *co, char *options)
2631{
2632 int ret;
2633 struct uart_port *port = &atmel_ports[co->index].uart;
2634 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2635 int baud = 115200;
2636 int bits = 8;
2637 int parity = 'n';
2638 int flow = 'n';
2639
2640 if (port->membase == NULL) {
2641 /* Port not initialized yet - delay setup */
2642 return -ENODEV;
2643 }
2644
2645 ret = clk_prepare_enable(atmel_ports[co->index].clk);
2646 if (ret)
2647 return ret;
2648
2649 atmel_uart_writel(port, ATMEL_US_IDR, -1);
2650 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
2651 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_TXEN | ATMEL_US_RXEN);
2652 atmel_port->tx_stopped = false;
2653
2654 if (options)
2655 uart_parse_options(options, &baud, &parity, &bits, &flow);
2656 else
2657 atmel_console_get_options(port, &baud, &parity, &bits);
2658
2659 return uart_set_options(port, co, baud, parity, bits, flow);
2660}
2661
2662static struct uart_driver atmel_uart;
2663
2664static struct console atmel_console = {
2665 .name = ATMEL_DEVICENAME,
2666 .write = atmel_console_write,
2667 .device = uart_console_device,
2668 .setup = atmel_console_setup,
2669 .flags = CON_PRINTBUFFER,
2670 .index = -1,
2671 .data = &atmel_uart,
2672};
2673
2674#define ATMEL_CONSOLE_DEVICE (&atmel_console)
2675
2676static inline bool atmel_is_console_port(struct uart_port *port)
2677{
2678 return port->cons && port->cons->index == port->line;
2679}
2680
2681#else
2682#define ATMEL_CONSOLE_DEVICE NULL
2683
2684static inline bool atmel_is_console_port(struct uart_port *port)
2685{
2686 return false;
2687}
2688#endif
2689
2690static struct uart_driver atmel_uart = {
2691 .owner = THIS_MODULE,
2692 .driver_name = "atmel_serial",
2693 .dev_name = ATMEL_DEVICENAME,
2694 .major = SERIAL_ATMEL_MAJOR,
2695 .minor = MINOR_START,
2696 .nr = ATMEL_MAX_UART,
2697 .cons = ATMEL_CONSOLE_DEVICE,
2698};
2699
2700#ifdef CONFIG_PM
2701static bool atmel_serial_clk_will_stop(void)
2702{
2703#ifdef CONFIG_ARCH_AT91
2704 return at91_suspend_entering_slow_clock();
2705#else
2706 return false;
2707#endif
2708}
2709
2710static int atmel_serial_suspend(struct platform_device *pdev,
2711 pm_message_t state)
2712{
2713 struct uart_port *port = platform_get_drvdata(pdev);
2714 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2715
2716 if (atmel_is_console_port(port) && console_suspend_enabled) {
2717 /* Drain the TX shifter */
2718 while (!(atmel_uart_readl(port, ATMEL_US_CSR) &
2719 ATMEL_US_TXEMPTY))
2720 cpu_relax();
2721 }
2722
2723 if (atmel_is_console_port(port) && !console_suspend_enabled) {
2724 /* Cache register values as we won't get a full shutdown/startup
2725 * cycle
2726 */
2727 atmel_port->cache.mr = atmel_uart_readl(port, ATMEL_US_MR);
2728 atmel_port->cache.imr = atmel_uart_readl(port, ATMEL_US_IMR);
2729 atmel_port->cache.brgr = atmel_uart_readl(port, ATMEL_US_BRGR);
2730 atmel_port->cache.rtor = atmel_uart_readl(port,
2731 atmel_port->rtor);
2732 atmel_port->cache.ttgr = atmel_uart_readl(port, ATMEL_US_TTGR);
2733 atmel_port->cache.fmr = atmel_uart_readl(port, ATMEL_US_FMR);
2734 atmel_port->cache.fimr = atmel_uart_readl(port, ATMEL_US_FIMR);
2735 }
2736
2737 /* we can not wake up if we're running on slow clock */
2738 atmel_port->may_wakeup = device_may_wakeup(&pdev->dev);
2739 if (atmel_serial_clk_will_stop()) {
2740 unsigned long flags;
2741
2742 spin_lock_irqsave(&atmel_port->lock_suspended, flags);
2743 atmel_port->suspended = true;
2744 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags);
2745 device_set_wakeup_enable(&pdev->dev, 0);
2746 }
2747
2748 uart_suspend_port(&atmel_uart, port);
2749
2750 return 0;
2751}
2752
2753static int atmel_serial_resume(struct platform_device *pdev)
2754{
2755 struct uart_port *port = platform_get_drvdata(pdev);
2756 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2757 unsigned long flags;
2758
2759 if (atmel_is_console_port(port) && !console_suspend_enabled) {
2760 atmel_uart_writel(port, ATMEL_US_MR, atmel_port->cache.mr);
2761 atmel_uart_writel(port, ATMEL_US_IER, atmel_port->cache.imr);
2762 atmel_uart_writel(port, ATMEL_US_BRGR, atmel_port->cache.brgr);
2763 atmel_uart_writel(port, atmel_port->rtor,
2764 atmel_port->cache.rtor);
2765 atmel_uart_writel(port, ATMEL_US_TTGR, atmel_port->cache.ttgr);
2766
2767 if (atmel_port->fifo_size) {
2768 atmel_uart_writel(port, ATMEL_US_CR, ATMEL_US_FIFOEN |
2769 ATMEL_US_RXFCLR | ATMEL_US_TXFLCLR);
2770 atmel_uart_writel(port, ATMEL_US_FMR,
2771 atmel_port->cache.fmr);
2772 atmel_uart_writel(port, ATMEL_US_FIER,
2773 atmel_port->cache.fimr);
2774 }
2775 atmel_start_rx(port);
2776 }
2777
2778 spin_lock_irqsave(&atmel_port->lock_suspended, flags);
2779 if (atmel_port->pending) {
2780 atmel_handle_receive(port, atmel_port->pending);
2781 atmel_handle_status(port, atmel_port->pending,
2782 atmel_port->pending_status);
2783 atmel_handle_transmit(port, atmel_port->pending);
2784 atmel_port->pending = 0;
2785 }
2786 atmel_port->suspended = false;
2787 spin_unlock_irqrestore(&atmel_port->lock_suspended, flags);
2788
2789 uart_resume_port(&atmel_uart, port);
2790 device_set_wakeup_enable(&pdev->dev, atmel_port->may_wakeup);
2791
2792 return 0;
2793}
2794#else
2795#define atmel_serial_suspend NULL
2796#define atmel_serial_resume NULL
2797#endif
2798
2799static void atmel_serial_probe_fifos(struct atmel_uart_port *atmel_port,
2800 struct platform_device *pdev)
2801{
2802 atmel_port->fifo_size = 0;
2803 atmel_port->rts_low = 0;
2804 atmel_port->rts_high = 0;
2805
2806 if (of_property_read_u32(pdev->dev.of_node,
2807 "atmel,fifo-size",
2808 &atmel_port->fifo_size))
2809 return;
2810
2811 if (!atmel_port->fifo_size)
2812 return;
2813
2814 if (atmel_port->fifo_size < ATMEL_MIN_FIFO_SIZE) {
2815 atmel_port->fifo_size = 0;
2816 dev_err(&pdev->dev, "Invalid FIFO size\n");
2817 return;
2818 }
2819
2820 /*
2821 * 0 <= rts_low <= rts_high <= fifo_size
2822 * Once their CTS line asserted by the remote peer, some x86 UARTs tend
2823 * to flush their internal TX FIFO, commonly up to 16 data, before
2824 * actually stopping to send new data. So we try to set the RTS High
2825 * Threshold to a reasonably high value respecting this 16 data
2826 * empirical rule when possible.
2827 */
2828 atmel_port->rts_high = max_t(int, atmel_port->fifo_size >> 1,
2829 atmel_port->fifo_size - ATMEL_RTS_HIGH_OFFSET);
2830 atmel_port->rts_low = max_t(int, atmel_port->fifo_size >> 2,
2831 atmel_port->fifo_size - ATMEL_RTS_LOW_OFFSET);
2832
2833 dev_info(&pdev->dev, "Using FIFO (%u data)\n",
2834 atmel_port->fifo_size);
2835 dev_dbg(&pdev->dev, "RTS High Threshold : %2u data\n",
2836 atmel_port->rts_high);
2837 dev_dbg(&pdev->dev, "RTS Low Threshold : %2u data\n",
2838 atmel_port->rts_low);
2839}
2840
2841static int atmel_serial_probe(struct platform_device *pdev)
2842{
2843 struct atmel_uart_port *atmel_port;
2844 struct device_node *np = pdev->dev.parent->of_node;
2845 void *data;
2846 int ret;
2847 bool rs485_enabled;
2848
2849 BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
2850
2851 /*
2852 * In device tree there is no node with "atmel,at91rm9200-usart-serial"
2853 * as compatible string. This driver is probed by at91-usart mfd driver
2854 * which is just a wrapper over the atmel_serial driver and
2855 * spi-at91-usart driver. All attributes needed by this driver are
2856 * found in of_node of parent.
2857 */
2858 pdev->dev.of_node = np;
2859
2860 ret = of_alias_get_id(np, "serial");
2861 if (ret < 0)
2862 /* port id not found in platform data nor device-tree aliases:
2863 * auto-enumerate it */
2864 ret = find_first_zero_bit(atmel_ports_in_use, ATMEL_MAX_UART);
2865
2866 if (ret >= ATMEL_MAX_UART) {
2867 ret = -ENODEV;
2868 goto err;
2869 }
2870
2871 if (test_and_set_bit(ret, atmel_ports_in_use)) {
2872 /* port already in use */
2873 ret = -EBUSY;
2874 goto err;
2875 }
2876
2877 atmel_port = &atmel_ports[ret];
2878 atmel_port->backup_imr = 0;
2879 atmel_port->uart.line = ret;
2880 atmel_serial_probe_fifos(atmel_port, pdev);
2881
2882 atomic_set(&atmel_port->tasklet_shutdown, 0);
2883 spin_lock_init(&atmel_port->lock_suspended);
2884
2885 ret = atmel_init_port(atmel_port, pdev);
2886 if (ret)
2887 goto err_clear_bit;
2888
2889 atmel_port->gpios = mctrl_gpio_init(&atmel_port->uart, 0);
2890 if (IS_ERR(atmel_port->gpios)) {
2891 ret = PTR_ERR(atmel_port->gpios);
2892 goto err_clear_bit;
2893 }
2894
2895 if (!atmel_use_pdc_rx(&atmel_port->uart)) {
2896 ret = -ENOMEM;
2897 data = kmalloc_array(ATMEL_SERIAL_RINGSIZE,
2898 sizeof(struct atmel_uart_char),
2899 GFP_KERNEL);
2900 if (!data)
2901 goto err_alloc_ring;
2902 atmel_port->rx_ring.buf = data;
2903 }
2904
2905 rs485_enabled = atmel_port->uart.rs485.flags & SER_RS485_ENABLED;
2906
2907 ret = uart_add_one_port(&atmel_uart, &atmel_port->uart);
2908 if (ret)
2909 goto err_add_port;
2910
2911#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
2912 if (atmel_is_console_port(&atmel_port->uart)
2913 && ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) {
2914 /*
2915 * The serial core enabled the clock for us, so undo
2916 * the clk_prepare_enable() in atmel_console_setup()
2917 */
2918 clk_disable_unprepare(atmel_port->clk);
2919 }
2920#endif
2921
2922 device_init_wakeup(&pdev->dev, 1);
2923 platform_set_drvdata(pdev, atmel_port);
2924
2925 /*
2926 * The peripheral clock has been disabled by atmel_init_port():
2927 * enable it before accessing I/O registers
2928 */
2929 clk_prepare_enable(atmel_port->clk);
2930
2931 if (rs485_enabled) {
2932 atmel_uart_writel(&atmel_port->uart, ATMEL_US_MR,
2933 ATMEL_US_USMODE_NORMAL);
2934 atmel_uart_writel(&atmel_port->uart, ATMEL_US_CR,
2935 ATMEL_US_RTSEN);
2936 }
2937
2938 /*
2939 * Get port name of usart or uart
2940 */
2941 atmel_get_ip_name(&atmel_port->uart);
2942
2943 /*
2944 * The peripheral clock can now safely be disabled till the port
2945 * is used
2946 */
2947 clk_disable_unprepare(atmel_port->clk);
2948
2949 return 0;
2950
2951err_add_port:
2952 kfree(atmel_port->rx_ring.buf);
2953 atmel_port->rx_ring.buf = NULL;
2954err_alloc_ring:
2955 if (!atmel_is_console_port(&atmel_port->uart)) {
2956 clk_put(atmel_port->clk);
2957 atmel_port->clk = NULL;
2958 }
2959err_clear_bit:
2960 clear_bit(atmel_port->uart.line, atmel_ports_in_use);
2961err:
2962 return ret;
2963}
2964
2965/*
2966 * Even if the driver is not modular, it makes sense to be able to
2967 * unbind a device: there can be many bound devices, and there are
2968 * situations where dynamic binding and unbinding can be useful.
2969 *
2970 * For example, a connected device can require a specific firmware update
2971 * protocol that needs bitbanging on IO lines, but use the regular serial
2972 * port in the normal case.
2973 */
2974static int atmel_serial_remove(struct platform_device *pdev)
2975{
2976 struct uart_port *port = platform_get_drvdata(pdev);
2977 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2978 int ret = 0;
2979
2980 tasklet_kill(&atmel_port->tasklet_rx);
2981 tasklet_kill(&atmel_port->tasklet_tx);
2982
2983 device_init_wakeup(&pdev->dev, 0);
2984
2985 ret = uart_remove_one_port(&atmel_uart, port);
2986
2987 kfree(atmel_port->rx_ring.buf);
2988
2989 /* "port" is allocated statically, so we shouldn't free it */
2990
2991 clear_bit(port->line, atmel_ports_in_use);
2992
2993 clk_put(atmel_port->clk);
2994 atmel_port->clk = NULL;
2995 pdev->dev.of_node = NULL;
2996
2997 return ret;
2998}
2999
3000static struct platform_driver atmel_serial_driver = {
3001 .probe = atmel_serial_probe,
3002 .remove = atmel_serial_remove,
3003 .suspend = atmel_serial_suspend,
3004 .resume = atmel_serial_resume,
3005 .driver = {
3006 .name = "atmel_usart_serial",
3007 .of_match_table = of_match_ptr(atmel_serial_dt_ids),
3008 },
3009};
3010
3011static int __init atmel_serial_init(void)
3012{
3013 int ret;
3014
3015 ret = uart_register_driver(&atmel_uart);
3016 if (ret)
3017 return ret;
3018
3019 ret = platform_driver_register(&atmel_serial_driver);
3020 if (ret)
3021 uart_unregister_driver(&atmel_uart);
3022
3023 return ret;
3024}
3025device_initcall(atmel_serial_init);
1/*
2 * Driver for Atmel AT91 / AT32 Serial ports
3 * Copyright (C) 2003 Rick Bronson
4 *
5 * Based on drivers/char/serial_sa1100.c, by Deep Blue Solutions Ltd.
6 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
7 *
8 * DMA support added by Chip Coldwell.
9 *
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License as published by
12 * the Free Software Foundation; either version 2 of the License, or
13 * (at your option) any later version.
14 *
15 * This program is distributed in the hope that it will be useful,
16 * but WITHOUT ANY WARRANTY; without even the implied warranty of
17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
18 * GNU General Public License for more details.
19 *
20 * You should have received a copy of the GNU General Public License
21 * along with this program; if not, write to the Free Software
22 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
23 *
24 */
25#include <linux/module.h>
26#include <linux/tty.h>
27#include <linux/ioport.h>
28#include <linux/slab.h>
29#include <linux/init.h>
30#include <linux/serial.h>
31#include <linux/clk.h>
32#include <linux/console.h>
33#include <linux/sysrq.h>
34#include <linux/tty_flip.h>
35#include <linux/platform_device.h>
36#include <linux/of.h>
37#include <linux/of_device.h>
38#include <linux/of_gpio.h>
39#include <linux/dma-mapping.h>
40#include <linux/atmel_pdc.h>
41#include <linux/atmel_serial.h>
42#include <linux/uaccess.h>
43#include <linux/platform_data/atmel.h>
44#include <linux/timer.h>
45#include <linux/gpio.h>
46
47#include <asm/io.h>
48#include <asm/ioctls.h>
49
50#define PDC_BUFFER_SIZE 512
51/* Revisit: We should calculate this based on the actual port settings */
52#define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */
53
54#if defined(CONFIG_SERIAL_ATMEL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
55#define SUPPORT_SYSRQ
56#endif
57
58#include <linux/serial_core.h>
59
60static void atmel_start_rx(struct uart_port *port);
61static void atmel_stop_rx(struct uart_port *port);
62
63#ifdef CONFIG_SERIAL_ATMEL_TTYAT
64
65/* Use device name ttyAT, major 204 and minor 154-169. This is necessary if we
66 * should coexist with the 8250 driver, such as if we have an external 16C550
67 * UART. */
68#define SERIAL_ATMEL_MAJOR 204
69#define MINOR_START 154
70#define ATMEL_DEVICENAME "ttyAT"
71
72#else
73
74/* Use device name ttyS, major 4, minor 64-68. This is the usual serial port
75 * name, but it is legally reserved for the 8250 driver. */
76#define SERIAL_ATMEL_MAJOR TTY_MAJOR
77#define MINOR_START 64
78#define ATMEL_DEVICENAME "ttyS"
79
80#endif
81
82#define ATMEL_ISR_PASS_LIMIT 256
83
84/* UART registers. CR is write-only, hence no GET macro */
85#define UART_PUT_CR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_CR)
86#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR)
87#define UART_PUT_MR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_MR)
88#define UART_PUT_IER(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IER)
89#define UART_PUT_IDR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IDR)
90#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR)
91#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR)
92#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR)
93#define UART_PUT_CHAR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_THR)
94#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR)
95#define UART_PUT_BRGR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR)
96#define UART_PUT_RTOR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR)
97#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR)
98#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME)
99#define UART_GET_IP_VERSION(port) __raw_readl((port)->membase + ATMEL_US_VERSION)
100
101 /* PDC registers */
102#define UART_PUT_PTCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR)
103#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR)
104
105#define UART_PUT_RPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR)
106#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR)
107#define UART_PUT_RCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR)
108#define UART_PUT_RNPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR)
109#define UART_PUT_RNCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR)
110
111#define UART_PUT_TPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR)
112#define UART_PUT_TCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR)
113#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR)
114
115struct atmel_dma_buffer {
116 unsigned char *buf;
117 dma_addr_t dma_addr;
118 unsigned int dma_size;
119 unsigned int ofs;
120};
121
122struct atmel_uart_char {
123 u16 status;
124 u16 ch;
125};
126
127#define ATMEL_SERIAL_RINGSIZE 1024
128
129/*
130 * We wrap our port structure around the generic uart_port.
131 */
132struct atmel_uart_port {
133 struct uart_port uart; /* uart */
134 struct clk *clk; /* uart clock */
135 int may_wakeup; /* cached value of device_may_wakeup for times we need to disable it */
136 u32 backup_imr; /* IMR saved during suspend */
137 int break_active; /* break being received */
138
139 bool use_dma_rx; /* enable DMA receiver */
140 bool use_pdc_rx; /* enable PDC receiver */
141 short pdc_rx_idx; /* current PDC RX buffer */
142 struct atmel_dma_buffer pdc_rx[2]; /* PDC receier */
143
144 bool use_dma_tx; /* enable DMA transmitter */
145 bool use_pdc_tx; /* enable PDC transmitter */
146 struct atmel_dma_buffer pdc_tx; /* PDC transmitter */
147
148 spinlock_t lock_tx; /* port lock */
149 spinlock_t lock_rx; /* port lock */
150 struct dma_chan *chan_tx;
151 struct dma_chan *chan_rx;
152 struct dma_async_tx_descriptor *desc_tx;
153 struct dma_async_tx_descriptor *desc_rx;
154 dma_cookie_t cookie_tx;
155 dma_cookie_t cookie_rx;
156 struct scatterlist sg_tx;
157 struct scatterlist sg_rx;
158 struct tasklet_struct tasklet;
159 unsigned int irq_status;
160 unsigned int irq_status_prev;
161
162 struct circ_buf rx_ring;
163
164 struct serial_rs485 rs485; /* rs485 settings */
165 int rts_gpio; /* optional RTS GPIO */
166 unsigned int tx_done_mask;
167 bool is_usart; /* usart or uart */
168 struct timer_list uart_timer; /* uart timer */
169 int (*prepare_rx)(struct uart_port *port);
170 int (*prepare_tx)(struct uart_port *port);
171 void (*schedule_rx)(struct uart_port *port);
172 void (*schedule_tx)(struct uart_port *port);
173 void (*release_rx)(struct uart_port *port);
174 void (*release_tx)(struct uart_port *port);
175};
176
177static struct atmel_uart_port atmel_ports[ATMEL_MAX_UART];
178static DECLARE_BITMAP(atmel_ports_in_use, ATMEL_MAX_UART);
179
180#ifdef SUPPORT_SYSRQ
181static struct console atmel_console;
182#endif
183
184#if defined(CONFIG_OF)
185static const struct of_device_id atmel_serial_dt_ids[] = {
186 { .compatible = "atmel,at91rm9200-usart" },
187 { .compatible = "atmel,at91sam9260-usart" },
188 { /* sentinel */ }
189};
190
191MODULE_DEVICE_TABLE(of, atmel_serial_dt_ids);
192#endif
193
194static inline struct atmel_uart_port *
195to_atmel_uart_port(struct uart_port *uart)
196{
197 return container_of(uart, struct atmel_uart_port, uart);
198}
199
200#ifdef CONFIG_SERIAL_ATMEL_PDC
201static bool atmel_use_pdc_rx(struct uart_port *port)
202{
203 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
204
205 return atmel_port->use_pdc_rx;
206}
207
208static bool atmel_use_pdc_tx(struct uart_port *port)
209{
210 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
211
212 return atmel_port->use_pdc_tx;
213}
214#else
215static bool atmel_use_pdc_rx(struct uart_port *port)
216{
217 return false;
218}
219
220static bool atmel_use_pdc_tx(struct uart_port *port)
221{
222 return false;
223}
224#endif
225
226static bool atmel_use_dma_tx(struct uart_port *port)
227{
228 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
229
230 return atmel_port->use_dma_tx;
231}
232
233static bool atmel_use_dma_rx(struct uart_port *port)
234{
235 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
236
237 return atmel_port->use_dma_rx;
238}
239
240/* Enable or disable the rs485 support */
241void atmel_config_rs485(struct uart_port *port, struct serial_rs485 *rs485conf)
242{
243 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
244 unsigned int mode;
245 unsigned long flags;
246
247 spin_lock_irqsave(&port->lock, flags);
248
249 /* Disable interrupts */
250 UART_PUT_IDR(port, atmel_port->tx_done_mask);
251
252 mode = UART_GET_MR(port);
253
254 /* Resetting serial mode to RS232 (0x0) */
255 mode &= ~ATMEL_US_USMODE;
256
257 atmel_port->rs485 = *rs485conf;
258
259 if (rs485conf->flags & SER_RS485_ENABLED) {
260 dev_dbg(port->dev, "Setting UART to RS485\n");
261 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
262 if ((rs485conf->delay_rts_after_send) > 0)
263 UART_PUT_TTGR(port, rs485conf->delay_rts_after_send);
264 mode |= ATMEL_US_USMODE_RS485;
265 } else {
266 dev_dbg(port->dev, "Setting UART to RS232\n");
267 if (atmel_use_pdc_tx(port))
268 atmel_port->tx_done_mask = ATMEL_US_ENDTX |
269 ATMEL_US_TXBUFE;
270 else
271 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
272 }
273 UART_PUT_MR(port, mode);
274
275 /* Enable interrupts */
276 UART_PUT_IER(port, atmel_port->tx_done_mask);
277
278 spin_unlock_irqrestore(&port->lock, flags);
279
280}
281
282/*
283 * Return TIOCSER_TEMT when transmitter FIFO and Shift register is empty.
284 */
285static u_int atmel_tx_empty(struct uart_port *port)
286{
287 return (UART_GET_CSR(port) & ATMEL_US_TXEMPTY) ? TIOCSER_TEMT : 0;
288}
289
290/*
291 * Set state of the modem control output lines
292 */
293static void atmel_set_mctrl(struct uart_port *port, u_int mctrl)
294{
295 unsigned int control = 0;
296 unsigned int mode;
297 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
298
299 /*
300 * AT91RM9200 Errata #39: RTS0 is not internally connected
301 * to PA21. We need to drive the pin as a GPIO.
302 */
303 if (gpio_is_valid(atmel_port->rts_gpio)) {
304 if (mctrl & TIOCM_RTS)
305 gpio_set_value(atmel_port->rts_gpio, 0);
306 else
307 gpio_set_value(atmel_port->rts_gpio, 1);
308 }
309
310 if (mctrl & TIOCM_RTS)
311 control |= ATMEL_US_RTSEN;
312 else
313 control |= ATMEL_US_RTSDIS;
314
315 if (mctrl & TIOCM_DTR)
316 control |= ATMEL_US_DTREN;
317 else
318 control |= ATMEL_US_DTRDIS;
319
320 UART_PUT_CR(port, control);
321
322 /* Local loopback mode? */
323 mode = UART_GET_MR(port) & ~ATMEL_US_CHMODE;
324 if (mctrl & TIOCM_LOOP)
325 mode |= ATMEL_US_CHMODE_LOC_LOOP;
326 else
327 mode |= ATMEL_US_CHMODE_NORMAL;
328
329 /* Resetting serial mode to RS232 (0x0) */
330 mode &= ~ATMEL_US_USMODE;
331
332 if (atmel_port->rs485.flags & SER_RS485_ENABLED) {
333 dev_dbg(port->dev, "Setting UART to RS485\n");
334 if ((atmel_port->rs485.delay_rts_after_send) > 0)
335 UART_PUT_TTGR(port,
336 atmel_port->rs485.delay_rts_after_send);
337 mode |= ATMEL_US_USMODE_RS485;
338 } else {
339 dev_dbg(port->dev, "Setting UART to RS232\n");
340 }
341 UART_PUT_MR(port, mode);
342}
343
344/*
345 * Get state of the modem control input lines
346 */
347static u_int atmel_get_mctrl(struct uart_port *port)
348{
349 unsigned int status, ret = 0;
350
351 status = UART_GET_CSR(port);
352
353 /*
354 * The control signals are active low.
355 */
356 if (!(status & ATMEL_US_DCD))
357 ret |= TIOCM_CD;
358 if (!(status & ATMEL_US_CTS))
359 ret |= TIOCM_CTS;
360 if (!(status & ATMEL_US_DSR))
361 ret |= TIOCM_DSR;
362 if (!(status & ATMEL_US_RI))
363 ret |= TIOCM_RI;
364
365 return ret;
366}
367
368/*
369 * Stop transmitting.
370 */
371static void atmel_stop_tx(struct uart_port *port)
372{
373 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
374
375 if (atmel_use_pdc_tx(port)) {
376 /* disable PDC transmit */
377 UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);
378 }
379 /* Disable interrupts */
380 UART_PUT_IDR(port, atmel_port->tx_done_mask);
381
382 if ((atmel_port->rs485.flags & SER_RS485_ENABLED) &&
383 !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX))
384 atmel_start_rx(port);
385}
386
387/*
388 * Start transmitting.
389 */
390static void atmel_start_tx(struct uart_port *port)
391{
392 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
393
394 if (atmel_use_pdc_tx(port)) {
395 if (UART_GET_PTSR(port) & ATMEL_PDC_TXTEN)
396 /* The transmitter is already running. Yes, we
397 really need this.*/
398 return;
399
400 if ((atmel_port->rs485.flags & SER_RS485_ENABLED) &&
401 !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX))
402 atmel_stop_rx(port);
403
404 /* re-enable PDC transmit */
405 UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);
406 }
407 /* Enable interrupts */
408 UART_PUT_IER(port, atmel_port->tx_done_mask);
409}
410
411/*
412 * start receiving - port is in process of being opened.
413 */
414static void atmel_start_rx(struct uart_port *port)
415{
416 UART_PUT_CR(port, ATMEL_US_RSTSTA); /* reset status and receiver */
417
418 UART_PUT_CR(port, ATMEL_US_RXEN);
419
420 if (atmel_use_pdc_rx(port)) {
421 /* enable PDC controller */
422 UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
423 port->read_status_mask);
424 UART_PUT_PTCR(port, ATMEL_PDC_RXTEN);
425 } else {
426 UART_PUT_IER(port, ATMEL_US_RXRDY);
427 }
428}
429
430/*
431 * Stop receiving - port is in process of being closed.
432 */
433static void atmel_stop_rx(struct uart_port *port)
434{
435 UART_PUT_CR(port, ATMEL_US_RXDIS);
436
437 if (atmel_use_pdc_rx(port)) {
438 /* disable PDC receive */
439 UART_PUT_PTCR(port, ATMEL_PDC_RXTDIS);
440 UART_PUT_IDR(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT |
441 port->read_status_mask);
442 } else {
443 UART_PUT_IDR(port, ATMEL_US_RXRDY);
444 }
445}
446
447/*
448 * Enable modem status interrupts
449 */
450static void atmel_enable_ms(struct uart_port *port)
451{
452 UART_PUT_IER(port, ATMEL_US_RIIC | ATMEL_US_DSRIC
453 | ATMEL_US_DCDIC | ATMEL_US_CTSIC);
454}
455
456/*
457 * Control the transmission of a break signal
458 */
459static void atmel_break_ctl(struct uart_port *port, int break_state)
460{
461 if (break_state != 0)
462 UART_PUT_CR(port, ATMEL_US_STTBRK); /* start break */
463 else
464 UART_PUT_CR(port, ATMEL_US_STPBRK); /* stop break */
465}
466
467/*
468 * Stores the incoming character in the ring buffer
469 */
470static void
471atmel_buffer_rx_char(struct uart_port *port, unsigned int status,
472 unsigned int ch)
473{
474 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
475 struct circ_buf *ring = &atmel_port->rx_ring;
476 struct atmel_uart_char *c;
477
478 if (!CIRC_SPACE(ring->head, ring->tail, ATMEL_SERIAL_RINGSIZE))
479 /* Buffer overflow, ignore char */
480 return;
481
482 c = &((struct atmel_uart_char *)ring->buf)[ring->head];
483 c->status = status;
484 c->ch = ch;
485
486 /* Make sure the character is stored before we update head. */
487 smp_wmb();
488
489 ring->head = (ring->head + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
490}
491
492/*
493 * Deal with parity, framing and overrun errors.
494 */
495static void atmel_pdc_rxerr(struct uart_port *port, unsigned int status)
496{
497 /* clear error */
498 UART_PUT_CR(port, ATMEL_US_RSTSTA);
499
500 if (status & ATMEL_US_RXBRK) {
501 /* ignore side-effect */
502 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
503 port->icount.brk++;
504 }
505 if (status & ATMEL_US_PARE)
506 port->icount.parity++;
507 if (status & ATMEL_US_FRAME)
508 port->icount.frame++;
509 if (status & ATMEL_US_OVRE)
510 port->icount.overrun++;
511}
512
513/*
514 * Characters received (called from interrupt handler)
515 */
516static void atmel_rx_chars(struct uart_port *port)
517{
518 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
519 unsigned int status, ch;
520
521 status = UART_GET_CSR(port);
522 while (status & ATMEL_US_RXRDY) {
523 ch = UART_GET_CHAR(port);
524
525 /*
526 * note that the error handling code is
527 * out of the main execution path
528 */
529 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
530 | ATMEL_US_OVRE | ATMEL_US_RXBRK)
531 || atmel_port->break_active)) {
532
533 /* clear error */
534 UART_PUT_CR(port, ATMEL_US_RSTSTA);
535
536 if (status & ATMEL_US_RXBRK
537 && !atmel_port->break_active) {
538 atmel_port->break_active = 1;
539 UART_PUT_IER(port, ATMEL_US_RXBRK);
540 } else {
541 /*
542 * This is either the end-of-break
543 * condition or we've received at
544 * least one character without RXBRK
545 * being set. In both cases, the next
546 * RXBRK will indicate start-of-break.
547 */
548 UART_PUT_IDR(port, ATMEL_US_RXBRK);
549 status &= ~ATMEL_US_RXBRK;
550 atmel_port->break_active = 0;
551 }
552 }
553
554 atmel_buffer_rx_char(port, status, ch);
555 status = UART_GET_CSR(port);
556 }
557
558 tasklet_schedule(&atmel_port->tasklet);
559}
560
561/*
562 * Transmit characters (called from tasklet with TXRDY interrupt
563 * disabled)
564 */
565static void atmel_tx_chars(struct uart_port *port)
566{
567 struct circ_buf *xmit = &port->state->xmit;
568 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
569
570 if (port->x_char && UART_GET_CSR(port) & atmel_port->tx_done_mask) {
571 UART_PUT_CHAR(port, port->x_char);
572 port->icount.tx++;
573 port->x_char = 0;
574 }
575 if (uart_circ_empty(xmit) || uart_tx_stopped(port))
576 return;
577
578 while (UART_GET_CSR(port) & atmel_port->tx_done_mask) {
579 UART_PUT_CHAR(port, xmit->buf[xmit->tail]);
580 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
581 port->icount.tx++;
582 if (uart_circ_empty(xmit))
583 break;
584 }
585
586 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
587 uart_write_wakeup(port);
588
589 if (!uart_circ_empty(xmit))
590 /* Enable interrupts */
591 UART_PUT_IER(port, atmel_port->tx_done_mask);
592}
593
594static void atmel_complete_tx_dma(void *arg)
595{
596 struct atmel_uart_port *atmel_port = arg;
597 struct uart_port *port = &atmel_port->uart;
598 struct circ_buf *xmit = &port->state->xmit;
599 struct dma_chan *chan = atmel_port->chan_tx;
600 unsigned long flags;
601
602 spin_lock_irqsave(&port->lock, flags);
603
604 if (chan)
605 dmaengine_terminate_all(chan);
606 xmit->tail += sg_dma_len(&atmel_port->sg_tx);
607 xmit->tail &= UART_XMIT_SIZE - 1;
608
609 port->icount.tx += sg_dma_len(&atmel_port->sg_tx);
610
611 spin_lock_irq(&atmel_port->lock_tx);
612 async_tx_ack(atmel_port->desc_tx);
613 atmel_port->cookie_tx = -EINVAL;
614 atmel_port->desc_tx = NULL;
615 spin_unlock_irq(&atmel_port->lock_tx);
616
617 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
618 uart_write_wakeup(port);
619
620 /* Do we really need this? */
621 if (!uart_circ_empty(xmit))
622 tasklet_schedule(&atmel_port->tasklet);
623
624 spin_unlock_irqrestore(&port->lock, flags);
625}
626
627static void atmel_release_tx_dma(struct uart_port *port)
628{
629 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
630 struct dma_chan *chan = atmel_port->chan_tx;
631
632 if (chan) {
633 dmaengine_terminate_all(chan);
634 dma_release_channel(chan);
635 dma_unmap_sg(port->dev, &atmel_port->sg_tx, 1,
636 DMA_MEM_TO_DEV);
637 }
638
639 atmel_port->desc_tx = NULL;
640 atmel_port->chan_tx = NULL;
641 atmel_port->cookie_tx = -EINVAL;
642}
643
644/*
645 * Called from tasklet with TXRDY interrupt is disabled.
646 */
647static void atmel_tx_dma(struct uart_port *port)
648{
649 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
650 struct circ_buf *xmit = &port->state->xmit;
651 struct dma_chan *chan = atmel_port->chan_tx;
652 struct dma_async_tx_descriptor *desc;
653 struct scatterlist *sg = &atmel_port->sg_tx;
654
655 /* Make sure we have an idle channel */
656 if (atmel_port->desc_tx != NULL)
657 return;
658
659 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
660 /*
661 * DMA is idle now.
662 * Port xmit buffer is already mapped,
663 * and it is one page... Just adjust
664 * offsets and lengths. Since it is a circular buffer,
665 * we have to transmit till the end, and then the rest.
666 * Take the port lock to get a
667 * consistent xmit buffer state.
668 */
669 sg->offset = xmit->tail & (UART_XMIT_SIZE - 1);
670 sg_dma_address(sg) = (sg_dma_address(sg) &
671 ~(UART_XMIT_SIZE - 1))
672 + sg->offset;
673 sg_dma_len(sg) = CIRC_CNT_TO_END(xmit->head,
674 xmit->tail,
675 UART_XMIT_SIZE);
676 BUG_ON(!sg_dma_len(sg));
677
678 desc = dmaengine_prep_slave_sg(chan,
679 sg,
680 1,
681 DMA_MEM_TO_DEV,
682 DMA_PREP_INTERRUPT |
683 DMA_CTRL_ACK);
684 if (!desc) {
685 dev_err(port->dev, "Failed to send via dma!\n");
686 return;
687 }
688
689 dma_sync_sg_for_device(port->dev, sg, 1, DMA_MEM_TO_DEV);
690
691 atmel_port->desc_tx = desc;
692 desc->callback = atmel_complete_tx_dma;
693 desc->callback_param = atmel_port;
694 atmel_port->cookie_tx = dmaengine_submit(desc);
695
696 } else {
697 if (atmel_port->rs485.flags & SER_RS485_ENABLED) {
698 /* DMA done, stop TX, start RX for RS485 */
699 atmel_start_rx(port);
700 }
701 }
702
703 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
704 uart_write_wakeup(port);
705}
706
707static int atmel_prepare_tx_dma(struct uart_port *port)
708{
709 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
710 dma_cap_mask_t mask;
711 struct dma_slave_config config;
712 int ret, nent;
713
714 dma_cap_zero(mask);
715 dma_cap_set(DMA_SLAVE, mask);
716
717 atmel_port->chan_tx = dma_request_slave_channel(port->dev, "tx");
718 if (atmel_port->chan_tx == NULL)
719 goto chan_err;
720 dev_info(port->dev, "using %s for tx DMA transfers\n",
721 dma_chan_name(atmel_port->chan_tx));
722
723 spin_lock_init(&atmel_port->lock_tx);
724 sg_init_table(&atmel_port->sg_tx, 1);
725 /* UART circular tx buffer is an aligned page. */
726 BUG_ON((int)port->state->xmit.buf & ~PAGE_MASK);
727 sg_set_page(&atmel_port->sg_tx,
728 virt_to_page(port->state->xmit.buf),
729 UART_XMIT_SIZE,
730 (int)port->state->xmit.buf & ~PAGE_MASK);
731 nent = dma_map_sg(port->dev,
732 &atmel_port->sg_tx,
733 1,
734 DMA_MEM_TO_DEV);
735
736 if (!nent) {
737 dev_dbg(port->dev, "need to release resource of dma\n");
738 goto chan_err;
739 } else {
740 dev_dbg(port->dev, "%s: mapped %d@%p to %x\n", __func__,
741 sg_dma_len(&atmel_port->sg_tx),
742 port->state->xmit.buf,
743 sg_dma_address(&atmel_port->sg_tx));
744 }
745
746 /* Configure the slave DMA */
747 memset(&config, 0, sizeof(config));
748 config.direction = DMA_MEM_TO_DEV;
749 config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
750 config.dst_addr = port->mapbase + ATMEL_US_THR;
751
752 ret = dmaengine_device_control(atmel_port->chan_tx,
753 DMA_SLAVE_CONFIG,
754 (unsigned long)&config);
755 if (ret) {
756 dev_err(port->dev, "DMA tx slave configuration failed\n");
757 goto chan_err;
758 }
759
760 return 0;
761
762chan_err:
763 dev_err(port->dev, "TX channel not available, switch to pio\n");
764 atmel_port->use_dma_tx = 0;
765 if (atmel_port->chan_tx)
766 atmel_release_tx_dma(port);
767 return -EINVAL;
768}
769
770static void atmel_flip_buffer_rx_dma(struct uart_port *port,
771 char *buf, size_t count)
772{
773 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
774 struct tty_port *tport = &port->state->port;
775
776 dma_sync_sg_for_cpu(port->dev,
777 &atmel_port->sg_rx,
778 1,
779 DMA_DEV_TO_MEM);
780
781 tty_insert_flip_string(tport, buf, count);
782
783 dma_sync_sg_for_device(port->dev,
784 &atmel_port->sg_rx,
785 1,
786 DMA_DEV_TO_MEM);
787 /*
788 * Drop the lock here since it might end up calling
789 * uart_start(), which takes the lock.
790 */
791 spin_unlock(&port->lock);
792 tty_flip_buffer_push(tport);
793 spin_lock(&port->lock);
794}
795
796static void atmel_complete_rx_dma(void *arg)
797{
798 struct uart_port *port = arg;
799 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
800
801 tasklet_schedule(&atmel_port->tasklet);
802}
803
804static void atmel_release_rx_dma(struct uart_port *port)
805{
806 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
807 struct dma_chan *chan = atmel_port->chan_rx;
808
809 if (chan) {
810 dmaengine_terminate_all(chan);
811 dma_release_channel(chan);
812 dma_unmap_sg(port->dev, &atmel_port->sg_rx, 1,
813 DMA_DEV_TO_MEM);
814 }
815
816 atmel_port->desc_rx = NULL;
817 atmel_port->chan_rx = NULL;
818 atmel_port->cookie_rx = -EINVAL;
819}
820
821static void atmel_rx_from_dma(struct uart_port *port)
822{
823 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
824 struct circ_buf *ring = &atmel_port->rx_ring;
825 struct dma_chan *chan = atmel_port->chan_rx;
826 struct dma_tx_state state;
827 enum dma_status dmastat;
828 size_t pending, count;
829
830
831 /* Reset the UART timeout early so that we don't miss one */
832 UART_PUT_CR(port, ATMEL_US_STTTO);
833 dmastat = dmaengine_tx_status(chan,
834 atmel_port->cookie_rx,
835 &state);
836 /* Restart a new tasklet if DMA status is error */
837 if (dmastat == DMA_ERROR) {
838 dev_dbg(port->dev, "Get residue error, restart tasklet\n");
839 UART_PUT_IER(port, ATMEL_US_TIMEOUT);
840 tasklet_schedule(&atmel_port->tasklet);
841 return;
842 }
843 /* current transfer size should no larger than dma buffer */
844 pending = sg_dma_len(&atmel_port->sg_rx) - state.residue;
845 BUG_ON(pending > sg_dma_len(&atmel_port->sg_rx));
846
847 /*
848 * This will take the chars we have so far,
849 * ring->head will record the transfer size, only new bytes come
850 * will insert into the framework.
851 */
852 if (pending > ring->head) {
853 count = pending - ring->head;
854
855 atmel_flip_buffer_rx_dma(port, ring->buf + ring->head, count);
856
857 ring->head += count;
858 if (ring->head == sg_dma_len(&atmel_port->sg_rx))
859 ring->head = 0;
860
861 port->icount.rx += count;
862 }
863
864 UART_PUT_IER(port, ATMEL_US_TIMEOUT);
865}
866
867static int atmel_prepare_rx_dma(struct uart_port *port)
868{
869 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
870 struct dma_async_tx_descriptor *desc;
871 dma_cap_mask_t mask;
872 struct dma_slave_config config;
873 struct circ_buf *ring;
874 int ret, nent;
875
876 ring = &atmel_port->rx_ring;
877
878 dma_cap_zero(mask);
879 dma_cap_set(DMA_CYCLIC, mask);
880
881 atmel_port->chan_rx = dma_request_slave_channel(port->dev, "rx");
882 if (atmel_port->chan_rx == NULL)
883 goto chan_err;
884 dev_info(port->dev, "using %s for rx DMA transfers\n",
885 dma_chan_name(atmel_port->chan_rx));
886
887 spin_lock_init(&atmel_port->lock_rx);
888 sg_init_table(&atmel_port->sg_rx, 1);
889 /* UART circular rx buffer is an aligned page. */
890 BUG_ON((int)port->state->xmit.buf & ~PAGE_MASK);
891 sg_set_page(&atmel_port->sg_rx,
892 virt_to_page(ring->buf),
893 ATMEL_SERIAL_RINGSIZE,
894 (int)ring->buf & ~PAGE_MASK);
895 nent = dma_map_sg(port->dev,
896 &atmel_port->sg_rx,
897 1,
898 DMA_DEV_TO_MEM);
899
900 if (!nent) {
901 dev_dbg(port->dev, "need to release resource of dma\n");
902 goto chan_err;
903 } else {
904 dev_dbg(port->dev, "%s: mapped %d@%p to %x\n", __func__,
905 sg_dma_len(&atmel_port->sg_rx),
906 ring->buf,
907 sg_dma_address(&atmel_port->sg_rx));
908 }
909
910 /* Configure the slave DMA */
911 memset(&config, 0, sizeof(config));
912 config.direction = DMA_DEV_TO_MEM;
913 config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
914 config.src_addr = port->mapbase + ATMEL_US_RHR;
915
916 ret = dmaengine_device_control(atmel_port->chan_rx,
917 DMA_SLAVE_CONFIG,
918 (unsigned long)&config);
919 if (ret) {
920 dev_err(port->dev, "DMA rx slave configuration failed\n");
921 goto chan_err;
922 }
923 /*
924 * Prepare a cyclic dma transfer, assign 2 descriptors,
925 * each one is half ring buffer size
926 */
927 desc = dmaengine_prep_dma_cyclic(atmel_port->chan_rx,
928 sg_dma_address(&atmel_port->sg_rx),
929 sg_dma_len(&atmel_port->sg_rx),
930 sg_dma_len(&atmel_port->sg_rx)/2,
931 DMA_DEV_TO_MEM,
932 DMA_PREP_INTERRUPT);
933 desc->callback = atmel_complete_rx_dma;
934 desc->callback_param = port;
935 atmel_port->desc_rx = desc;
936 atmel_port->cookie_rx = dmaengine_submit(desc);
937
938 return 0;
939
940chan_err:
941 dev_err(port->dev, "RX channel not available, switch to pio\n");
942 atmel_port->use_dma_rx = 0;
943 if (atmel_port->chan_rx)
944 atmel_release_rx_dma(port);
945 return -EINVAL;
946}
947
948static void atmel_uart_timer_callback(unsigned long data)
949{
950 struct uart_port *port = (void *)data;
951 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
952
953 tasklet_schedule(&atmel_port->tasklet);
954 mod_timer(&atmel_port->uart_timer, jiffies + uart_poll_timeout(port));
955}
956
957/*
958 * receive interrupt handler.
959 */
960static void
961atmel_handle_receive(struct uart_port *port, unsigned int pending)
962{
963 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
964
965 if (atmel_use_pdc_rx(port)) {
966 /*
967 * PDC receive. Just schedule the tasklet and let it
968 * figure out the details.
969 *
970 * TODO: We're not handling error flags correctly at
971 * the moment.
972 */
973 if (pending & (ATMEL_US_ENDRX | ATMEL_US_TIMEOUT)) {
974 UART_PUT_IDR(port, (ATMEL_US_ENDRX
975 | ATMEL_US_TIMEOUT));
976 tasklet_schedule(&atmel_port->tasklet);
977 }
978
979 if (pending & (ATMEL_US_RXBRK | ATMEL_US_OVRE |
980 ATMEL_US_FRAME | ATMEL_US_PARE))
981 atmel_pdc_rxerr(port, pending);
982 }
983
984 if (atmel_use_dma_rx(port)) {
985 if (pending & ATMEL_US_TIMEOUT) {
986 UART_PUT_IDR(port, ATMEL_US_TIMEOUT);
987 tasklet_schedule(&atmel_port->tasklet);
988 }
989 }
990
991 /* Interrupt receive */
992 if (pending & ATMEL_US_RXRDY)
993 atmel_rx_chars(port);
994 else if (pending & ATMEL_US_RXBRK) {
995 /*
996 * End of break detected. If it came along with a
997 * character, atmel_rx_chars will handle it.
998 */
999 UART_PUT_CR(port, ATMEL_US_RSTSTA);
1000 UART_PUT_IDR(port, ATMEL_US_RXBRK);
1001 atmel_port->break_active = 0;
1002 }
1003}
1004
1005/*
1006 * transmit interrupt handler. (Transmit is IRQF_NODELAY safe)
1007 */
1008static void
1009atmel_handle_transmit(struct uart_port *port, unsigned int pending)
1010{
1011 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1012
1013 if (pending & atmel_port->tx_done_mask) {
1014 /* Either PDC or interrupt transmission */
1015 UART_PUT_IDR(port, atmel_port->tx_done_mask);
1016 tasklet_schedule(&atmel_port->tasklet);
1017 }
1018}
1019
1020/*
1021 * status flags interrupt handler.
1022 */
1023static void
1024atmel_handle_status(struct uart_port *port, unsigned int pending,
1025 unsigned int status)
1026{
1027 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1028
1029 if (pending & (ATMEL_US_RIIC | ATMEL_US_DSRIC | ATMEL_US_DCDIC
1030 | ATMEL_US_CTSIC)) {
1031 atmel_port->irq_status = status;
1032 tasklet_schedule(&atmel_port->tasklet);
1033 }
1034}
1035
1036/*
1037 * Interrupt handler
1038 */
1039static irqreturn_t atmel_interrupt(int irq, void *dev_id)
1040{
1041 struct uart_port *port = dev_id;
1042 unsigned int status, pending, pass_counter = 0;
1043
1044 do {
1045 status = UART_GET_CSR(port);
1046 pending = status & UART_GET_IMR(port);
1047 if (!pending)
1048 break;
1049
1050 atmel_handle_receive(port, pending);
1051 atmel_handle_status(port, pending, status);
1052 atmel_handle_transmit(port, pending);
1053 } while (pass_counter++ < ATMEL_ISR_PASS_LIMIT);
1054
1055 return pass_counter ? IRQ_HANDLED : IRQ_NONE;
1056}
1057
1058static void atmel_release_tx_pdc(struct uart_port *port)
1059{
1060 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1061 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1062
1063 dma_unmap_single(port->dev,
1064 pdc->dma_addr,
1065 pdc->dma_size,
1066 DMA_TO_DEVICE);
1067}
1068
1069/*
1070 * Called from tasklet with ENDTX and TXBUFE interrupts disabled.
1071 */
1072static void atmel_tx_pdc(struct uart_port *port)
1073{
1074 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1075 struct circ_buf *xmit = &port->state->xmit;
1076 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1077 int count;
1078
1079 /* nothing left to transmit? */
1080 if (UART_GET_TCR(port))
1081 return;
1082
1083 xmit->tail += pdc->ofs;
1084 xmit->tail &= UART_XMIT_SIZE - 1;
1085
1086 port->icount.tx += pdc->ofs;
1087 pdc->ofs = 0;
1088
1089 /* more to transmit - setup next transfer */
1090
1091 /* disable PDC transmit */
1092 UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);
1093
1094 if (!uart_circ_empty(xmit) && !uart_tx_stopped(port)) {
1095 dma_sync_single_for_device(port->dev,
1096 pdc->dma_addr,
1097 pdc->dma_size,
1098 DMA_TO_DEVICE);
1099
1100 count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
1101 pdc->ofs = count;
1102
1103 UART_PUT_TPR(port, pdc->dma_addr + xmit->tail);
1104 UART_PUT_TCR(port, count);
1105 /* re-enable PDC transmit */
1106 UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);
1107 /* Enable interrupts */
1108 UART_PUT_IER(port, atmel_port->tx_done_mask);
1109 } else {
1110 if ((atmel_port->rs485.flags & SER_RS485_ENABLED) &&
1111 !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX)) {
1112 /* DMA done, stop TX, start RX for RS485 */
1113 atmel_start_rx(port);
1114 }
1115 }
1116
1117 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
1118 uart_write_wakeup(port);
1119}
1120
1121static int atmel_prepare_tx_pdc(struct uart_port *port)
1122{
1123 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1124 struct atmel_dma_buffer *pdc = &atmel_port->pdc_tx;
1125 struct circ_buf *xmit = &port->state->xmit;
1126
1127 pdc->buf = xmit->buf;
1128 pdc->dma_addr = dma_map_single(port->dev,
1129 pdc->buf,
1130 UART_XMIT_SIZE,
1131 DMA_TO_DEVICE);
1132 pdc->dma_size = UART_XMIT_SIZE;
1133 pdc->ofs = 0;
1134
1135 return 0;
1136}
1137
1138static void atmel_rx_from_ring(struct uart_port *port)
1139{
1140 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1141 struct circ_buf *ring = &atmel_port->rx_ring;
1142 unsigned int flg;
1143 unsigned int status;
1144
1145 while (ring->head != ring->tail) {
1146 struct atmel_uart_char c;
1147
1148 /* Make sure c is loaded after head. */
1149 smp_rmb();
1150
1151 c = ((struct atmel_uart_char *)ring->buf)[ring->tail];
1152
1153 ring->tail = (ring->tail + 1) & (ATMEL_SERIAL_RINGSIZE - 1);
1154
1155 port->icount.rx++;
1156 status = c.status;
1157 flg = TTY_NORMAL;
1158
1159 /*
1160 * note that the error handling code is
1161 * out of the main execution path
1162 */
1163 if (unlikely(status & (ATMEL_US_PARE | ATMEL_US_FRAME
1164 | ATMEL_US_OVRE | ATMEL_US_RXBRK))) {
1165 if (status & ATMEL_US_RXBRK) {
1166 /* ignore side-effect */
1167 status &= ~(ATMEL_US_PARE | ATMEL_US_FRAME);
1168
1169 port->icount.brk++;
1170 if (uart_handle_break(port))
1171 continue;
1172 }
1173 if (status & ATMEL_US_PARE)
1174 port->icount.parity++;
1175 if (status & ATMEL_US_FRAME)
1176 port->icount.frame++;
1177 if (status & ATMEL_US_OVRE)
1178 port->icount.overrun++;
1179
1180 status &= port->read_status_mask;
1181
1182 if (status & ATMEL_US_RXBRK)
1183 flg = TTY_BREAK;
1184 else if (status & ATMEL_US_PARE)
1185 flg = TTY_PARITY;
1186 else if (status & ATMEL_US_FRAME)
1187 flg = TTY_FRAME;
1188 }
1189
1190
1191 if (uart_handle_sysrq_char(port, c.ch))
1192 continue;
1193
1194 uart_insert_char(port, status, ATMEL_US_OVRE, c.ch, flg);
1195 }
1196
1197 /*
1198 * Drop the lock here since it might end up calling
1199 * uart_start(), which takes the lock.
1200 */
1201 spin_unlock(&port->lock);
1202 tty_flip_buffer_push(&port->state->port);
1203 spin_lock(&port->lock);
1204}
1205
1206static void atmel_release_rx_pdc(struct uart_port *port)
1207{
1208 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1209 int i;
1210
1211 for (i = 0; i < 2; i++) {
1212 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1213
1214 dma_unmap_single(port->dev,
1215 pdc->dma_addr,
1216 pdc->dma_size,
1217 DMA_FROM_DEVICE);
1218 kfree(pdc->buf);
1219 }
1220}
1221
1222static void atmel_rx_from_pdc(struct uart_port *port)
1223{
1224 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1225 struct tty_port *tport = &port->state->port;
1226 struct atmel_dma_buffer *pdc;
1227 int rx_idx = atmel_port->pdc_rx_idx;
1228 unsigned int head;
1229 unsigned int tail;
1230 unsigned int count;
1231
1232 do {
1233 /* Reset the UART timeout early so that we don't miss one */
1234 UART_PUT_CR(port, ATMEL_US_STTTO);
1235
1236 pdc = &atmel_port->pdc_rx[rx_idx];
1237 head = UART_GET_RPR(port) - pdc->dma_addr;
1238 tail = pdc->ofs;
1239
1240 /* If the PDC has switched buffers, RPR won't contain
1241 * any address within the current buffer. Since head
1242 * is unsigned, we just need a one-way comparison to
1243 * find out.
1244 *
1245 * In this case, we just need to consume the entire
1246 * buffer and resubmit it for DMA. This will clear the
1247 * ENDRX bit as well, so that we can safely re-enable
1248 * all interrupts below.
1249 */
1250 head = min(head, pdc->dma_size);
1251
1252 if (likely(head != tail)) {
1253 dma_sync_single_for_cpu(port->dev, pdc->dma_addr,
1254 pdc->dma_size, DMA_FROM_DEVICE);
1255
1256 /*
1257 * head will only wrap around when we recycle
1258 * the DMA buffer, and when that happens, we
1259 * explicitly set tail to 0. So head will
1260 * always be greater than tail.
1261 */
1262 count = head - tail;
1263
1264 tty_insert_flip_string(tport, pdc->buf + pdc->ofs,
1265 count);
1266
1267 dma_sync_single_for_device(port->dev, pdc->dma_addr,
1268 pdc->dma_size, DMA_FROM_DEVICE);
1269
1270 port->icount.rx += count;
1271 pdc->ofs = head;
1272 }
1273
1274 /*
1275 * If the current buffer is full, we need to check if
1276 * the next one contains any additional data.
1277 */
1278 if (head >= pdc->dma_size) {
1279 pdc->ofs = 0;
1280 UART_PUT_RNPR(port, pdc->dma_addr);
1281 UART_PUT_RNCR(port, pdc->dma_size);
1282
1283 rx_idx = !rx_idx;
1284 atmel_port->pdc_rx_idx = rx_idx;
1285 }
1286 } while (head >= pdc->dma_size);
1287
1288 /*
1289 * Drop the lock here since it might end up calling
1290 * uart_start(), which takes the lock.
1291 */
1292 spin_unlock(&port->lock);
1293 tty_flip_buffer_push(tport);
1294 spin_lock(&port->lock);
1295
1296 UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1297}
1298
1299static int atmel_prepare_rx_pdc(struct uart_port *port)
1300{
1301 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1302 int i;
1303
1304 for (i = 0; i < 2; i++) {
1305 struct atmel_dma_buffer *pdc = &atmel_port->pdc_rx[i];
1306
1307 pdc->buf = kmalloc(PDC_BUFFER_SIZE, GFP_KERNEL);
1308 if (pdc->buf == NULL) {
1309 if (i != 0) {
1310 dma_unmap_single(port->dev,
1311 atmel_port->pdc_rx[0].dma_addr,
1312 PDC_BUFFER_SIZE,
1313 DMA_FROM_DEVICE);
1314 kfree(atmel_port->pdc_rx[0].buf);
1315 }
1316 atmel_port->use_pdc_rx = 0;
1317 return -ENOMEM;
1318 }
1319 pdc->dma_addr = dma_map_single(port->dev,
1320 pdc->buf,
1321 PDC_BUFFER_SIZE,
1322 DMA_FROM_DEVICE);
1323 pdc->dma_size = PDC_BUFFER_SIZE;
1324 pdc->ofs = 0;
1325 }
1326
1327 atmel_port->pdc_rx_idx = 0;
1328
1329 UART_PUT_RPR(port, atmel_port->pdc_rx[0].dma_addr);
1330 UART_PUT_RCR(port, PDC_BUFFER_SIZE);
1331
1332 UART_PUT_RNPR(port, atmel_port->pdc_rx[1].dma_addr);
1333 UART_PUT_RNCR(port, PDC_BUFFER_SIZE);
1334
1335 return 0;
1336}
1337
1338/*
1339 * tasklet handling tty stuff outside the interrupt handler.
1340 */
1341static void atmel_tasklet_func(unsigned long data)
1342{
1343 struct uart_port *port = (struct uart_port *)data;
1344 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1345 unsigned int status;
1346 unsigned int status_change;
1347
1348 /* The interrupt handler does not take the lock */
1349 spin_lock(&port->lock);
1350
1351 atmel_port->schedule_tx(port);
1352
1353 status = atmel_port->irq_status;
1354 status_change = status ^ atmel_port->irq_status_prev;
1355
1356 if (status_change & (ATMEL_US_RI | ATMEL_US_DSR
1357 | ATMEL_US_DCD | ATMEL_US_CTS)) {
1358 /* TODO: All reads to CSR will clear these interrupts! */
1359 if (status_change & ATMEL_US_RI)
1360 port->icount.rng++;
1361 if (status_change & ATMEL_US_DSR)
1362 port->icount.dsr++;
1363 if (status_change & ATMEL_US_DCD)
1364 uart_handle_dcd_change(port, !(status & ATMEL_US_DCD));
1365 if (status_change & ATMEL_US_CTS)
1366 uart_handle_cts_change(port, !(status & ATMEL_US_CTS));
1367
1368 wake_up_interruptible(&port->state->port.delta_msr_wait);
1369
1370 atmel_port->irq_status_prev = status;
1371 }
1372
1373 atmel_port->schedule_rx(port);
1374
1375 spin_unlock(&port->lock);
1376}
1377
1378static int atmel_init_property(struct atmel_uart_port *atmel_port,
1379 struct platform_device *pdev)
1380{
1381 struct device_node *np = pdev->dev.of_node;
1382 struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev);
1383
1384 if (np) {
1385 /* DMA/PDC usage specification */
1386 if (of_get_property(np, "atmel,use-dma-rx", NULL)) {
1387 if (of_get_property(np, "dmas", NULL)) {
1388 atmel_port->use_dma_rx = true;
1389 atmel_port->use_pdc_rx = false;
1390 } else {
1391 atmel_port->use_dma_rx = false;
1392 atmel_port->use_pdc_rx = true;
1393 }
1394 } else {
1395 atmel_port->use_dma_rx = false;
1396 atmel_port->use_pdc_rx = false;
1397 }
1398
1399 if (of_get_property(np, "atmel,use-dma-tx", NULL)) {
1400 if (of_get_property(np, "dmas", NULL)) {
1401 atmel_port->use_dma_tx = true;
1402 atmel_port->use_pdc_tx = false;
1403 } else {
1404 atmel_port->use_dma_tx = false;
1405 atmel_port->use_pdc_tx = true;
1406 }
1407 } else {
1408 atmel_port->use_dma_tx = false;
1409 atmel_port->use_pdc_tx = false;
1410 }
1411
1412 } else {
1413 atmel_port->use_pdc_rx = pdata->use_dma_rx;
1414 atmel_port->use_pdc_tx = pdata->use_dma_tx;
1415 atmel_port->use_dma_rx = false;
1416 atmel_port->use_dma_tx = false;
1417 }
1418
1419 return 0;
1420}
1421
1422static void atmel_init_rs485(struct atmel_uart_port *atmel_port,
1423 struct platform_device *pdev)
1424{
1425 struct device_node *np = pdev->dev.of_node;
1426 struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev);
1427
1428 if (np) {
1429 u32 rs485_delay[2];
1430 /* rs485 properties */
1431 if (of_property_read_u32_array(np, "rs485-rts-delay",
1432 rs485_delay, 2) == 0) {
1433 struct serial_rs485 *rs485conf = &atmel_port->rs485;
1434
1435 rs485conf->delay_rts_before_send = rs485_delay[0];
1436 rs485conf->delay_rts_after_send = rs485_delay[1];
1437 rs485conf->flags = 0;
1438
1439 if (of_get_property(np, "rs485-rx-during-tx", NULL))
1440 rs485conf->flags |= SER_RS485_RX_DURING_TX;
1441
1442 if (of_get_property(np, "linux,rs485-enabled-at-boot-time",
1443 NULL))
1444 rs485conf->flags |= SER_RS485_ENABLED;
1445 }
1446 } else {
1447 atmel_port->rs485 = pdata->rs485;
1448 }
1449
1450}
1451
1452static void atmel_set_ops(struct uart_port *port)
1453{
1454 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1455
1456 if (atmel_use_dma_rx(port)) {
1457 atmel_port->prepare_rx = &atmel_prepare_rx_dma;
1458 atmel_port->schedule_rx = &atmel_rx_from_dma;
1459 atmel_port->release_rx = &atmel_release_rx_dma;
1460 } else if (atmel_use_pdc_rx(port)) {
1461 atmel_port->prepare_rx = &atmel_prepare_rx_pdc;
1462 atmel_port->schedule_rx = &atmel_rx_from_pdc;
1463 atmel_port->release_rx = &atmel_release_rx_pdc;
1464 } else {
1465 atmel_port->prepare_rx = NULL;
1466 atmel_port->schedule_rx = &atmel_rx_from_ring;
1467 atmel_port->release_rx = NULL;
1468 }
1469
1470 if (atmel_use_dma_tx(port)) {
1471 atmel_port->prepare_tx = &atmel_prepare_tx_dma;
1472 atmel_port->schedule_tx = &atmel_tx_dma;
1473 atmel_port->release_tx = &atmel_release_tx_dma;
1474 } else if (atmel_use_pdc_tx(port)) {
1475 atmel_port->prepare_tx = &atmel_prepare_tx_pdc;
1476 atmel_port->schedule_tx = &atmel_tx_pdc;
1477 atmel_port->release_tx = &atmel_release_tx_pdc;
1478 } else {
1479 atmel_port->prepare_tx = NULL;
1480 atmel_port->schedule_tx = &atmel_tx_chars;
1481 atmel_port->release_tx = NULL;
1482 }
1483}
1484
1485/*
1486 * Get ip name usart or uart
1487 */
1488static void atmel_get_ip_name(struct uart_port *port)
1489{
1490 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1491 int name = UART_GET_IP_NAME(port);
1492 u32 version;
1493 int usart, uart;
1494 /* usart and uart ascii */
1495 usart = 0x55534152;
1496 uart = 0x44424755;
1497
1498 atmel_port->is_usart = false;
1499
1500 if (name == usart) {
1501 dev_dbg(port->dev, "This is usart\n");
1502 atmel_port->is_usart = true;
1503 } else if (name == uart) {
1504 dev_dbg(port->dev, "This is uart\n");
1505 atmel_port->is_usart = false;
1506 } else {
1507 /* fallback for older SoCs: use version field */
1508 version = UART_GET_IP_VERSION(port);
1509 switch (version) {
1510 case 0x302:
1511 case 0x10213:
1512 dev_dbg(port->dev, "This version is usart\n");
1513 atmel_port->is_usart = true;
1514 break;
1515 case 0x203:
1516 case 0x10202:
1517 dev_dbg(port->dev, "This version is uart\n");
1518 atmel_port->is_usart = false;
1519 break;
1520 default:
1521 dev_err(port->dev, "Not supported ip name nor version, set to uart\n");
1522 }
1523 }
1524}
1525
1526/*
1527 * Perform initialization and enable port for reception
1528 */
1529static int atmel_startup(struct uart_port *port)
1530{
1531 struct platform_device *pdev = to_platform_device(port->dev);
1532 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1533 struct tty_struct *tty = port->state->port.tty;
1534 int retval;
1535
1536 /*
1537 * Ensure that no interrupts are enabled otherwise when
1538 * request_irq() is called we could get stuck trying to
1539 * handle an unexpected interrupt
1540 */
1541 UART_PUT_IDR(port, -1);
1542
1543 /*
1544 * Allocate the IRQ
1545 */
1546 retval = request_irq(port->irq, atmel_interrupt, IRQF_SHARED,
1547 tty ? tty->name : "atmel_serial", port);
1548 if (retval) {
1549 dev_err(port->dev, "atmel_startup - Can't get irq\n");
1550 return retval;
1551 }
1552
1553 /*
1554 * Initialize DMA (if necessary)
1555 */
1556 atmel_init_property(atmel_port, pdev);
1557
1558 if (atmel_port->prepare_rx) {
1559 retval = atmel_port->prepare_rx(port);
1560 if (retval < 0)
1561 atmel_set_ops(port);
1562 }
1563
1564 if (atmel_port->prepare_tx) {
1565 retval = atmel_port->prepare_tx(port);
1566 if (retval < 0)
1567 atmel_set_ops(port);
1568 }
1569
1570 /* Save current CSR for comparison in atmel_tasklet_func() */
1571 atmel_port->irq_status_prev = UART_GET_CSR(port);
1572 atmel_port->irq_status = atmel_port->irq_status_prev;
1573
1574 /*
1575 * Finally, enable the serial port
1576 */
1577 UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
1578 /* enable xmit & rcvr */
1579 UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
1580
1581 setup_timer(&atmel_port->uart_timer,
1582 atmel_uart_timer_callback,
1583 (unsigned long)port);
1584
1585 if (atmel_use_pdc_rx(port)) {
1586 /* set UART timeout */
1587 if (!atmel_port->is_usart) {
1588 mod_timer(&atmel_port->uart_timer,
1589 jiffies + uart_poll_timeout(port));
1590 /* set USART timeout */
1591 } else {
1592 UART_PUT_RTOR(port, PDC_RX_TIMEOUT);
1593 UART_PUT_CR(port, ATMEL_US_STTTO);
1594
1595 UART_PUT_IER(port, ATMEL_US_ENDRX | ATMEL_US_TIMEOUT);
1596 }
1597 /* enable PDC controller */
1598 UART_PUT_PTCR(port, ATMEL_PDC_RXTEN);
1599 } else if (atmel_use_dma_rx(port)) {
1600 /* set UART timeout */
1601 if (!atmel_port->is_usart) {
1602 mod_timer(&atmel_port->uart_timer,
1603 jiffies + uart_poll_timeout(port));
1604 /* set USART timeout */
1605 } else {
1606 UART_PUT_RTOR(port, PDC_RX_TIMEOUT);
1607 UART_PUT_CR(port, ATMEL_US_STTTO);
1608
1609 UART_PUT_IER(port, ATMEL_US_TIMEOUT);
1610 }
1611 } else {
1612 /* enable receive only */
1613 UART_PUT_IER(port, ATMEL_US_RXRDY);
1614 }
1615
1616 return 0;
1617}
1618
1619/*
1620 * Disable the port
1621 */
1622static void atmel_shutdown(struct uart_port *port)
1623{
1624 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1625
1626 /*
1627 * Prevent any tasklets being scheduled during
1628 * cleanup
1629 */
1630 del_timer_sync(&atmel_port->uart_timer);
1631
1632 /*
1633 * Clear out any scheduled tasklets before
1634 * we destroy the buffers
1635 */
1636 tasklet_kill(&atmel_port->tasklet);
1637
1638 /*
1639 * Ensure everything is stopped and
1640 * disable all interrupts, port and break condition.
1641 */
1642 atmel_stop_rx(port);
1643 atmel_stop_tx(port);
1644
1645 UART_PUT_CR(port, ATMEL_US_RSTSTA);
1646 UART_PUT_IDR(port, -1);
1647
1648
1649 /*
1650 * Shut-down the DMA.
1651 */
1652 if (atmel_port->release_rx)
1653 atmel_port->release_rx(port);
1654 if (atmel_port->release_tx)
1655 atmel_port->release_tx(port);
1656
1657 /*
1658 * Reset ring buffer pointers
1659 */
1660 atmel_port->rx_ring.head = 0;
1661 atmel_port->rx_ring.tail = 0;
1662
1663 /*
1664 * Free the interrupt
1665 */
1666 free_irq(port->irq, port);
1667}
1668
1669/*
1670 * Flush any TX data submitted for DMA. Called when the TX circular
1671 * buffer is reset.
1672 */
1673static void atmel_flush_buffer(struct uart_port *port)
1674{
1675 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1676
1677 if (atmel_use_pdc_tx(port)) {
1678 UART_PUT_TCR(port, 0);
1679 atmel_port->pdc_tx.ofs = 0;
1680 }
1681}
1682
1683/*
1684 * Power / Clock management.
1685 */
1686static void atmel_serial_pm(struct uart_port *port, unsigned int state,
1687 unsigned int oldstate)
1688{
1689 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1690
1691 switch (state) {
1692 case 0:
1693 /*
1694 * Enable the peripheral clock for this serial port.
1695 * This is called on uart_open() or a resume event.
1696 */
1697 clk_prepare_enable(atmel_port->clk);
1698
1699 /* re-enable interrupts if we disabled some on suspend */
1700 UART_PUT_IER(port, atmel_port->backup_imr);
1701 break;
1702 case 3:
1703 /* Back up the interrupt mask and disable all interrupts */
1704 atmel_port->backup_imr = UART_GET_IMR(port);
1705 UART_PUT_IDR(port, -1);
1706
1707 /*
1708 * Disable the peripheral clock for this serial port.
1709 * This is called on uart_close() or a suspend event.
1710 */
1711 clk_disable_unprepare(atmel_port->clk);
1712 break;
1713 default:
1714 dev_err(port->dev, "atmel_serial: unknown pm %d\n", state);
1715 }
1716}
1717
1718/*
1719 * Change the port parameters
1720 */
1721static void atmel_set_termios(struct uart_port *port, struct ktermios *termios,
1722 struct ktermios *old)
1723{
1724 unsigned long flags;
1725 unsigned int mode, imr, quot, baud;
1726 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
1727
1728 /* Get current mode register */
1729 mode = UART_GET_MR(port) & ~(ATMEL_US_USCLKS | ATMEL_US_CHRL
1730 | ATMEL_US_NBSTOP | ATMEL_US_PAR
1731 | ATMEL_US_USMODE);
1732
1733 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
1734 quot = uart_get_divisor(port, baud);
1735
1736 if (quot > 65535) { /* BRGR is 16-bit, so switch to slower clock */
1737 quot /= 8;
1738 mode |= ATMEL_US_USCLKS_MCK_DIV8;
1739 }
1740
1741 /* byte size */
1742 switch (termios->c_cflag & CSIZE) {
1743 case CS5:
1744 mode |= ATMEL_US_CHRL_5;
1745 break;
1746 case CS6:
1747 mode |= ATMEL_US_CHRL_6;
1748 break;
1749 case CS7:
1750 mode |= ATMEL_US_CHRL_7;
1751 break;
1752 default:
1753 mode |= ATMEL_US_CHRL_8;
1754 break;
1755 }
1756
1757 /* stop bits */
1758 if (termios->c_cflag & CSTOPB)
1759 mode |= ATMEL_US_NBSTOP_2;
1760
1761 /* parity */
1762 if (termios->c_cflag & PARENB) {
1763 /* Mark or Space parity */
1764 if (termios->c_cflag & CMSPAR) {
1765 if (termios->c_cflag & PARODD)
1766 mode |= ATMEL_US_PAR_MARK;
1767 else
1768 mode |= ATMEL_US_PAR_SPACE;
1769 } else if (termios->c_cflag & PARODD)
1770 mode |= ATMEL_US_PAR_ODD;
1771 else
1772 mode |= ATMEL_US_PAR_EVEN;
1773 } else
1774 mode |= ATMEL_US_PAR_NONE;
1775
1776 /* hardware handshake (RTS/CTS) */
1777 if (termios->c_cflag & CRTSCTS)
1778 mode |= ATMEL_US_USMODE_HWHS;
1779 else
1780 mode |= ATMEL_US_USMODE_NORMAL;
1781
1782 spin_lock_irqsave(&port->lock, flags);
1783
1784 port->read_status_mask = ATMEL_US_OVRE;
1785 if (termios->c_iflag & INPCK)
1786 port->read_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
1787 if (termios->c_iflag & (BRKINT | PARMRK))
1788 port->read_status_mask |= ATMEL_US_RXBRK;
1789
1790 if (atmel_use_pdc_rx(port))
1791 /* need to enable error interrupts */
1792 UART_PUT_IER(port, port->read_status_mask);
1793
1794 /*
1795 * Characters to ignore
1796 */
1797 port->ignore_status_mask = 0;
1798 if (termios->c_iflag & IGNPAR)
1799 port->ignore_status_mask |= (ATMEL_US_FRAME | ATMEL_US_PARE);
1800 if (termios->c_iflag & IGNBRK) {
1801 port->ignore_status_mask |= ATMEL_US_RXBRK;
1802 /*
1803 * If we're ignoring parity and break indicators,
1804 * ignore overruns too (for real raw support).
1805 */
1806 if (termios->c_iflag & IGNPAR)
1807 port->ignore_status_mask |= ATMEL_US_OVRE;
1808 }
1809 /* TODO: Ignore all characters if CREAD is set.*/
1810
1811 /* update the per-port timeout */
1812 uart_update_timeout(port, termios->c_cflag, baud);
1813
1814 /*
1815 * save/disable interrupts. The tty layer will ensure that the
1816 * transmitter is empty if requested by the caller, so there's
1817 * no need to wait for it here.
1818 */
1819 imr = UART_GET_IMR(port);
1820 UART_PUT_IDR(port, -1);
1821
1822 /* disable receiver and transmitter */
1823 UART_PUT_CR(port, ATMEL_US_TXDIS | ATMEL_US_RXDIS);
1824
1825 /* Resetting serial mode to RS232 (0x0) */
1826 mode &= ~ATMEL_US_USMODE;
1827
1828 if (atmel_port->rs485.flags & SER_RS485_ENABLED) {
1829 if ((atmel_port->rs485.delay_rts_after_send) > 0)
1830 UART_PUT_TTGR(port,
1831 atmel_port->rs485.delay_rts_after_send);
1832 mode |= ATMEL_US_USMODE_RS485;
1833 }
1834
1835 /* set the parity, stop bits and data size */
1836 UART_PUT_MR(port, mode);
1837
1838 /* set the baud rate */
1839 UART_PUT_BRGR(port, quot);
1840 UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
1841 UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
1842
1843 /* restore interrupts */
1844 UART_PUT_IER(port, imr);
1845
1846 /* CTS flow-control and modem-status interrupts */
1847 if (UART_ENABLE_MS(port, termios->c_cflag))
1848 port->ops->enable_ms(port);
1849
1850 spin_unlock_irqrestore(&port->lock, flags);
1851}
1852
1853static void atmel_set_ldisc(struct uart_port *port, int new)
1854{
1855 if (new == N_PPS) {
1856 port->flags |= UPF_HARDPPS_CD;
1857 atmel_enable_ms(port);
1858 } else {
1859 port->flags &= ~UPF_HARDPPS_CD;
1860 }
1861}
1862
1863/*
1864 * Return string describing the specified port
1865 */
1866static const char *atmel_type(struct uart_port *port)
1867{
1868 return (port->type == PORT_ATMEL) ? "ATMEL_SERIAL" : NULL;
1869}
1870
1871/*
1872 * Release the memory region(s) being used by 'port'.
1873 */
1874static void atmel_release_port(struct uart_port *port)
1875{
1876 struct platform_device *pdev = to_platform_device(port->dev);
1877 int size = pdev->resource[0].end - pdev->resource[0].start + 1;
1878
1879 release_mem_region(port->mapbase, size);
1880
1881 if (port->flags & UPF_IOREMAP) {
1882 iounmap(port->membase);
1883 port->membase = NULL;
1884 }
1885}
1886
1887/*
1888 * Request the memory region(s) being used by 'port'.
1889 */
1890static int atmel_request_port(struct uart_port *port)
1891{
1892 struct platform_device *pdev = to_platform_device(port->dev);
1893 int size = pdev->resource[0].end - pdev->resource[0].start + 1;
1894
1895 if (!request_mem_region(port->mapbase, size, "atmel_serial"))
1896 return -EBUSY;
1897
1898 if (port->flags & UPF_IOREMAP) {
1899 port->membase = ioremap(port->mapbase, size);
1900 if (port->membase == NULL) {
1901 release_mem_region(port->mapbase, size);
1902 return -ENOMEM;
1903 }
1904 }
1905
1906 return 0;
1907}
1908
1909/*
1910 * Configure/autoconfigure the port.
1911 */
1912static void atmel_config_port(struct uart_port *port, int flags)
1913{
1914 if (flags & UART_CONFIG_TYPE) {
1915 port->type = PORT_ATMEL;
1916 atmel_request_port(port);
1917 }
1918}
1919
1920/*
1921 * Verify the new serial_struct (for TIOCSSERIAL).
1922 */
1923static int atmel_verify_port(struct uart_port *port, struct serial_struct *ser)
1924{
1925 int ret = 0;
1926 if (ser->type != PORT_UNKNOWN && ser->type != PORT_ATMEL)
1927 ret = -EINVAL;
1928 if (port->irq != ser->irq)
1929 ret = -EINVAL;
1930 if (ser->io_type != SERIAL_IO_MEM)
1931 ret = -EINVAL;
1932 if (port->uartclk / 16 != ser->baud_base)
1933 ret = -EINVAL;
1934 if ((void *)port->mapbase != ser->iomem_base)
1935 ret = -EINVAL;
1936 if (port->iobase != ser->port)
1937 ret = -EINVAL;
1938 if (ser->hub6 != 0)
1939 ret = -EINVAL;
1940 return ret;
1941}
1942
1943#ifdef CONFIG_CONSOLE_POLL
1944static int atmel_poll_get_char(struct uart_port *port)
1945{
1946 while (!(UART_GET_CSR(port) & ATMEL_US_RXRDY))
1947 cpu_relax();
1948
1949 return UART_GET_CHAR(port);
1950}
1951
1952static void atmel_poll_put_char(struct uart_port *port, unsigned char ch)
1953{
1954 while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY))
1955 cpu_relax();
1956
1957 UART_PUT_CHAR(port, ch);
1958}
1959#endif
1960
1961static int
1962atmel_ioctl(struct uart_port *port, unsigned int cmd, unsigned long arg)
1963{
1964 struct serial_rs485 rs485conf;
1965
1966 switch (cmd) {
1967 case TIOCSRS485:
1968 if (copy_from_user(&rs485conf, (struct serial_rs485 *) arg,
1969 sizeof(rs485conf)))
1970 return -EFAULT;
1971
1972 atmel_config_rs485(port, &rs485conf);
1973 break;
1974
1975 case TIOCGRS485:
1976 if (copy_to_user((struct serial_rs485 *) arg,
1977 &(to_atmel_uart_port(port)->rs485),
1978 sizeof(rs485conf)))
1979 return -EFAULT;
1980 break;
1981
1982 default:
1983 return -ENOIOCTLCMD;
1984 }
1985 return 0;
1986}
1987
1988
1989
1990static struct uart_ops atmel_pops = {
1991 .tx_empty = atmel_tx_empty,
1992 .set_mctrl = atmel_set_mctrl,
1993 .get_mctrl = atmel_get_mctrl,
1994 .stop_tx = atmel_stop_tx,
1995 .start_tx = atmel_start_tx,
1996 .stop_rx = atmel_stop_rx,
1997 .enable_ms = atmel_enable_ms,
1998 .break_ctl = atmel_break_ctl,
1999 .startup = atmel_startup,
2000 .shutdown = atmel_shutdown,
2001 .flush_buffer = atmel_flush_buffer,
2002 .set_termios = atmel_set_termios,
2003 .set_ldisc = atmel_set_ldisc,
2004 .type = atmel_type,
2005 .release_port = atmel_release_port,
2006 .request_port = atmel_request_port,
2007 .config_port = atmel_config_port,
2008 .verify_port = atmel_verify_port,
2009 .pm = atmel_serial_pm,
2010 .ioctl = atmel_ioctl,
2011#ifdef CONFIG_CONSOLE_POLL
2012 .poll_get_char = atmel_poll_get_char,
2013 .poll_put_char = atmel_poll_put_char,
2014#endif
2015};
2016
2017/*
2018 * Configure the port from the platform device resource info.
2019 */
2020static int atmel_init_port(struct atmel_uart_port *atmel_port,
2021 struct platform_device *pdev)
2022{
2023 int ret;
2024 struct uart_port *port = &atmel_port->uart;
2025 struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev);
2026
2027 if (!atmel_init_property(atmel_port, pdev))
2028 atmel_set_ops(port);
2029
2030 atmel_init_rs485(atmel_port, pdev);
2031
2032 port->iotype = UPIO_MEM;
2033 port->flags = UPF_BOOT_AUTOCONF;
2034 port->ops = &atmel_pops;
2035 port->fifosize = 1;
2036 port->dev = &pdev->dev;
2037 port->mapbase = pdev->resource[0].start;
2038 port->irq = pdev->resource[1].start;
2039
2040 tasklet_init(&atmel_port->tasklet, atmel_tasklet_func,
2041 (unsigned long)port);
2042
2043 memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
2044
2045 if (pdata && pdata->regs) {
2046 /* Already mapped by setup code */
2047 port->membase = pdata->regs;
2048 } else {
2049 port->flags |= UPF_IOREMAP;
2050 port->membase = NULL;
2051 }
2052
2053 /* for console, the clock could already be configured */
2054 if (!atmel_port->clk) {
2055 atmel_port->clk = clk_get(&pdev->dev, "usart");
2056 if (IS_ERR(atmel_port->clk)) {
2057 ret = PTR_ERR(atmel_port->clk);
2058 atmel_port->clk = NULL;
2059 return ret;
2060 }
2061 ret = clk_prepare_enable(atmel_port->clk);
2062 if (ret) {
2063 clk_put(atmel_port->clk);
2064 atmel_port->clk = NULL;
2065 return ret;
2066 }
2067 port->uartclk = clk_get_rate(atmel_port->clk);
2068 clk_disable_unprepare(atmel_port->clk);
2069 /* only enable clock when USART is in use */
2070 }
2071
2072 /* Use TXEMPTY for interrupt when rs485 else TXRDY or ENDTX|TXBUFE */
2073 if (atmel_port->rs485.flags & SER_RS485_ENABLED)
2074 atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
2075 else if (atmel_use_pdc_tx(port)) {
2076 port->fifosize = PDC_BUFFER_SIZE;
2077 atmel_port->tx_done_mask = ATMEL_US_ENDTX | ATMEL_US_TXBUFE;
2078 } else {
2079 atmel_port->tx_done_mask = ATMEL_US_TXRDY;
2080 }
2081
2082 return 0;
2083}
2084
2085struct platform_device *atmel_default_console_device; /* the serial console device */
2086
2087#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
2088static void atmel_console_putchar(struct uart_port *port, int ch)
2089{
2090 while (!(UART_GET_CSR(port) & ATMEL_US_TXRDY))
2091 cpu_relax();
2092 UART_PUT_CHAR(port, ch);
2093}
2094
2095/*
2096 * Interrupts are disabled on entering
2097 */
2098static void atmel_console_write(struct console *co, const char *s, u_int count)
2099{
2100 struct uart_port *port = &atmel_ports[co->index].uart;
2101 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2102 unsigned int status, imr;
2103 unsigned int pdc_tx;
2104
2105 /*
2106 * First, save IMR and then disable interrupts
2107 */
2108 imr = UART_GET_IMR(port);
2109 UART_PUT_IDR(port, ATMEL_US_RXRDY | atmel_port->tx_done_mask);
2110
2111 /* Store PDC transmit status and disable it */
2112 pdc_tx = UART_GET_PTSR(port) & ATMEL_PDC_TXTEN;
2113 UART_PUT_PTCR(port, ATMEL_PDC_TXTDIS);
2114
2115 uart_console_write(port, s, count, atmel_console_putchar);
2116
2117 /*
2118 * Finally, wait for transmitter to become empty
2119 * and restore IMR
2120 */
2121 do {
2122 status = UART_GET_CSR(port);
2123 } while (!(status & ATMEL_US_TXRDY));
2124
2125 /* Restore PDC transmit status */
2126 if (pdc_tx)
2127 UART_PUT_PTCR(port, ATMEL_PDC_TXTEN);
2128
2129 /* set interrupts back the way they were */
2130 UART_PUT_IER(port, imr);
2131}
2132
2133/*
2134 * If the port was already initialised (eg, by a boot loader),
2135 * try to determine the current setup.
2136 */
2137static void __init atmel_console_get_options(struct uart_port *port, int *baud,
2138 int *parity, int *bits)
2139{
2140 unsigned int mr, quot;
2141
2142 /*
2143 * If the baud rate generator isn't running, the port wasn't
2144 * initialized by the boot loader.
2145 */
2146 quot = UART_GET_BRGR(port) & ATMEL_US_CD;
2147 if (!quot)
2148 return;
2149
2150 mr = UART_GET_MR(port) & ATMEL_US_CHRL;
2151 if (mr == ATMEL_US_CHRL_8)
2152 *bits = 8;
2153 else
2154 *bits = 7;
2155
2156 mr = UART_GET_MR(port) & ATMEL_US_PAR;
2157 if (mr == ATMEL_US_PAR_EVEN)
2158 *parity = 'e';
2159 else if (mr == ATMEL_US_PAR_ODD)
2160 *parity = 'o';
2161
2162 /*
2163 * The serial core only rounds down when matching this to a
2164 * supported baud rate. Make sure we don't end up slightly
2165 * lower than one of those, as it would make us fall through
2166 * to a much lower baud rate than we really want.
2167 */
2168 *baud = port->uartclk / (16 * (quot - 1));
2169}
2170
2171static int __init atmel_console_setup(struct console *co, char *options)
2172{
2173 int ret;
2174 struct uart_port *port = &atmel_ports[co->index].uart;
2175 int baud = 115200;
2176 int bits = 8;
2177 int parity = 'n';
2178 int flow = 'n';
2179
2180 if (port->membase == NULL) {
2181 /* Port not initialized yet - delay setup */
2182 return -ENODEV;
2183 }
2184
2185 ret = clk_prepare_enable(atmel_ports[co->index].clk);
2186 if (ret)
2187 return ret;
2188
2189 UART_PUT_IDR(port, -1);
2190 UART_PUT_CR(port, ATMEL_US_RSTSTA | ATMEL_US_RSTRX);
2191 UART_PUT_CR(port, ATMEL_US_TXEN | ATMEL_US_RXEN);
2192
2193 if (options)
2194 uart_parse_options(options, &baud, &parity, &bits, &flow);
2195 else
2196 atmel_console_get_options(port, &baud, &parity, &bits);
2197
2198 return uart_set_options(port, co, baud, parity, bits, flow);
2199}
2200
2201static struct uart_driver atmel_uart;
2202
2203static struct console atmel_console = {
2204 .name = ATMEL_DEVICENAME,
2205 .write = atmel_console_write,
2206 .device = uart_console_device,
2207 .setup = atmel_console_setup,
2208 .flags = CON_PRINTBUFFER,
2209 .index = -1,
2210 .data = &atmel_uart,
2211};
2212
2213#define ATMEL_CONSOLE_DEVICE (&atmel_console)
2214
2215/*
2216 * Early console initialization (before VM subsystem initialized).
2217 */
2218static int __init atmel_console_init(void)
2219{
2220 int ret;
2221 if (atmel_default_console_device) {
2222 struct atmel_uart_data *pdata =
2223 dev_get_platdata(&atmel_default_console_device->dev);
2224 int id = pdata->num;
2225 struct atmel_uart_port *port = &atmel_ports[id];
2226
2227 port->backup_imr = 0;
2228 port->uart.line = id;
2229
2230 add_preferred_console(ATMEL_DEVICENAME, id, NULL);
2231 ret = atmel_init_port(port, atmel_default_console_device);
2232 if (ret)
2233 return ret;
2234 register_console(&atmel_console);
2235 }
2236
2237 return 0;
2238}
2239
2240console_initcall(atmel_console_init);
2241
2242/*
2243 * Late console initialization.
2244 */
2245static int __init atmel_late_console_init(void)
2246{
2247 if (atmel_default_console_device
2248 && !(atmel_console.flags & CON_ENABLED))
2249 register_console(&atmel_console);
2250
2251 return 0;
2252}
2253
2254core_initcall(atmel_late_console_init);
2255
2256static inline bool atmel_is_console_port(struct uart_port *port)
2257{
2258 return port->cons && port->cons->index == port->line;
2259}
2260
2261#else
2262#define ATMEL_CONSOLE_DEVICE NULL
2263
2264static inline bool atmel_is_console_port(struct uart_port *port)
2265{
2266 return false;
2267}
2268#endif
2269
2270static struct uart_driver atmel_uart = {
2271 .owner = THIS_MODULE,
2272 .driver_name = "atmel_serial",
2273 .dev_name = ATMEL_DEVICENAME,
2274 .major = SERIAL_ATMEL_MAJOR,
2275 .minor = MINOR_START,
2276 .nr = ATMEL_MAX_UART,
2277 .cons = ATMEL_CONSOLE_DEVICE,
2278};
2279
2280#ifdef CONFIG_PM
2281static bool atmel_serial_clk_will_stop(void)
2282{
2283#ifdef CONFIG_ARCH_AT91
2284 return at91_suspend_entering_slow_clock();
2285#else
2286 return false;
2287#endif
2288}
2289
2290static int atmel_serial_suspend(struct platform_device *pdev,
2291 pm_message_t state)
2292{
2293 struct uart_port *port = platform_get_drvdata(pdev);
2294 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2295
2296 if (atmel_is_console_port(port) && console_suspend_enabled) {
2297 /* Drain the TX shifter */
2298 while (!(UART_GET_CSR(port) & ATMEL_US_TXEMPTY))
2299 cpu_relax();
2300 }
2301
2302 /* we can not wake up if we're running on slow clock */
2303 atmel_port->may_wakeup = device_may_wakeup(&pdev->dev);
2304 if (atmel_serial_clk_will_stop())
2305 device_set_wakeup_enable(&pdev->dev, 0);
2306
2307 uart_suspend_port(&atmel_uart, port);
2308
2309 return 0;
2310}
2311
2312static int atmel_serial_resume(struct platform_device *pdev)
2313{
2314 struct uart_port *port = platform_get_drvdata(pdev);
2315 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2316
2317 uart_resume_port(&atmel_uart, port);
2318 device_set_wakeup_enable(&pdev->dev, atmel_port->may_wakeup);
2319
2320 return 0;
2321}
2322#else
2323#define atmel_serial_suspend NULL
2324#define atmel_serial_resume NULL
2325#endif
2326
2327static int atmel_serial_probe(struct platform_device *pdev)
2328{
2329 struct atmel_uart_port *port;
2330 struct device_node *np = pdev->dev.of_node;
2331 struct atmel_uart_data *pdata = dev_get_platdata(&pdev->dev);
2332 void *data;
2333 int ret = -ENODEV;
2334
2335 BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
2336
2337 if (np)
2338 ret = of_alias_get_id(np, "serial");
2339 else
2340 if (pdata)
2341 ret = pdata->num;
2342
2343 if (ret < 0)
2344 /* port id not found in platform data nor device-tree aliases:
2345 * auto-enumerate it */
2346 ret = find_first_zero_bit(atmel_ports_in_use, ATMEL_MAX_UART);
2347
2348 if (ret >= ATMEL_MAX_UART) {
2349 ret = -ENODEV;
2350 goto err;
2351 }
2352
2353 if (test_and_set_bit(ret, atmel_ports_in_use)) {
2354 /* port already in use */
2355 ret = -EBUSY;
2356 goto err;
2357 }
2358
2359 port = &atmel_ports[ret];
2360 port->backup_imr = 0;
2361 port->uart.line = ret;
2362 port->rts_gpio = -EINVAL; /* Invalid, zero could be valid */
2363 if (pdata)
2364 port->rts_gpio = pdata->rts_gpio;
2365 else if (np)
2366 port->rts_gpio = of_get_named_gpio(np, "rts-gpios", 0);
2367
2368 if (gpio_is_valid(port->rts_gpio)) {
2369 ret = devm_gpio_request(&pdev->dev, port->rts_gpio, "RTS");
2370 if (ret) {
2371 dev_err(&pdev->dev, "error requesting RTS GPIO\n");
2372 goto err;
2373 }
2374 /* Default to 1 as RTS is active low */
2375 ret = gpio_direction_output(port->rts_gpio, 1);
2376 if (ret) {
2377 dev_err(&pdev->dev, "error setting up RTS GPIO\n");
2378 goto err;
2379 }
2380 }
2381
2382 ret = atmel_init_port(port, pdev);
2383 if (ret)
2384 goto err;
2385
2386 if (!atmel_use_pdc_rx(&port->uart)) {
2387 ret = -ENOMEM;
2388 data = kmalloc(sizeof(struct atmel_uart_char)
2389 * ATMEL_SERIAL_RINGSIZE, GFP_KERNEL);
2390 if (!data)
2391 goto err_alloc_ring;
2392 port->rx_ring.buf = data;
2393 }
2394
2395 ret = uart_add_one_port(&atmel_uart, &port->uart);
2396 if (ret)
2397 goto err_add_port;
2398
2399#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
2400 if (atmel_is_console_port(&port->uart)
2401 && ATMEL_CONSOLE_DEVICE->flags & CON_ENABLED) {
2402 /*
2403 * The serial core enabled the clock for us, so undo
2404 * the clk_prepare_enable() in atmel_console_setup()
2405 */
2406 clk_disable_unprepare(port->clk);
2407 }
2408#endif
2409
2410 device_init_wakeup(&pdev->dev, 1);
2411 platform_set_drvdata(pdev, port);
2412
2413 if (port->rs485.flags & SER_RS485_ENABLED) {
2414 UART_PUT_MR(&port->uart, ATMEL_US_USMODE_NORMAL);
2415 UART_PUT_CR(&port->uart, ATMEL_US_RTSEN);
2416 }
2417
2418 /*
2419 * Get port name of usart or uart
2420 */
2421 atmel_get_ip_name(&port->uart);
2422
2423 return 0;
2424
2425err_add_port:
2426 kfree(port->rx_ring.buf);
2427 port->rx_ring.buf = NULL;
2428err_alloc_ring:
2429 if (!atmel_is_console_port(&port->uart)) {
2430 clk_put(port->clk);
2431 port->clk = NULL;
2432 }
2433err:
2434 return ret;
2435}
2436
2437static int atmel_serial_remove(struct platform_device *pdev)
2438{
2439 struct uart_port *port = platform_get_drvdata(pdev);
2440 struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
2441 int ret = 0;
2442
2443 tasklet_kill(&atmel_port->tasklet);
2444
2445 device_init_wakeup(&pdev->dev, 0);
2446
2447 ret = uart_remove_one_port(&atmel_uart, port);
2448
2449 kfree(atmel_port->rx_ring.buf);
2450
2451 /* "port" is allocated statically, so we shouldn't free it */
2452
2453 clear_bit(port->line, atmel_ports_in_use);
2454
2455 clk_put(atmel_port->clk);
2456
2457 return ret;
2458}
2459
2460static struct platform_driver atmel_serial_driver = {
2461 .probe = atmel_serial_probe,
2462 .remove = atmel_serial_remove,
2463 .suspend = atmel_serial_suspend,
2464 .resume = atmel_serial_resume,
2465 .driver = {
2466 .name = "atmel_usart",
2467 .owner = THIS_MODULE,
2468 .of_match_table = of_match_ptr(atmel_serial_dt_ids),
2469 },
2470};
2471
2472static int __init atmel_serial_init(void)
2473{
2474 int ret;
2475
2476 ret = uart_register_driver(&atmel_uart);
2477 if (ret)
2478 return ret;
2479
2480 ret = platform_driver_register(&atmel_serial_driver);
2481 if (ret)
2482 uart_unregister_driver(&atmel_uart);
2483
2484 return ret;
2485}
2486
2487static void __exit atmel_serial_exit(void)
2488{
2489 platform_driver_unregister(&atmel_serial_driver);
2490 uart_unregister_driver(&atmel_uart);
2491}
2492
2493module_init(atmel_serial_init);
2494module_exit(atmel_serial_exit);
2495
2496MODULE_AUTHOR("Rick Bronson");
2497MODULE_DESCRIPTION("Atmel AT91 / AT32 serial port driver");
2498MODULE_LICENSE("GPL");
2499MODULE_ALIAS("platform:atmel_usart");