Loading...
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * usb_a926x.dts - Device Tree file for Caloa USB A926x board
4 *
5 * Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
6 */
7
8/ {
9 clocks {
10 slow_xtal {
11 clock-frequency = <32768>;
12 };
13
14 main_xtal {
15 clock-frequency = <12000000>;
16 };
17 };
18
19 ahb {
20 apb {
21 dbgu: serial@fffff200 {
22 status = "okay";
23 };
24
25 tcb0: timer@fffa0000 {
26 timer@0 {
27 compatible = "atmel,tcb-timer";
28 reg = <0>, <1>;
29 };
30
31 timer@2 {
32 compatible = "atmel,tcb-timer";
33 reg = <2>;
34 };
35 };
36
37 macb0: ethernet@fffc4000 {
38 phy-mode = "rmii";
39 status = "okay";
40 };
41
42 usb1: gadget@fffa4000 {
43 atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
44 status = "okay";
45 };
46 };
47
48 ebi: ebi@10000000 {
49 status = "okay";
50
51 nand_controller: nand-controller {
52 status = "okay";
53 pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
54 pinctrl-names = "default";
55
56 nand@3 {
57 reg = <0x3 0x0 0x800000>;
58 rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
59 cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
60 nand-bus-width = <8>;
61 nand-ecc-mode = "soft";
62 nand-on-flash-bbt;
63 label = "atmel_nand";
64
65 partitions {
66 compatible = "fixed-partitions";
67 #address-cells = <1>;
68 #size-cells = <1>;
69
70 at91bootstrap@0 {
71 label = "at91bootstrap";
72 reg = <0x0 0x20000>;
73 };
74
75 barebox@20000 {
76 label = "barebox";
77 reg = <0x20000 0x40000>;
78 };
79
80 bareboxenv@60000 {
81 label = "bareboxenv";
82 reg = <0x60000 0x20000>;
83 };
84
85 bareboxenv2@80000 {
86 label = "bareboxenv2";
87 reg = <0x80000 0x20000>;
88 };
89
90 oftree@80000 {
91 label = "oftree";
92 reg = <0xa0000 0x20000>;
93 };
94
95 kernel@a0000 {
96 label = "kernel";
97 reg = <0xc0000 0x400000>;
98 };
99
100 rootfs@4a0000 {
101 label = "rootfs";
102 reg = <0x4c0000 0x7800000>;
103 };
104
105 data@7ca0000 {
106 label = "data";
107 reg = <0x7cc0000 0x8340000>;
108 };
109 };
110 };
111 };
112 };
113
114 usb0: ohci@500000 {
115 num-ports = <2>;
116 status = "okay";
117 };
118 };
119
120 leds {
121 compatible = "gpio-leds";
122
123 user_led {
124 label = "user_led";
125 gpios = <&pioB 21 GPIO_ACTIVE_LOW>;
126 linux,default-trigger = "heartbeat";
127 };
128 };
129
130 gpio_keys {
131 compatible = "gpio-keys";
132 #address-cells = <1>;
133 #size-cells = <0>;
134
135 user_pb {
136 label = "user_pb";
137 gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
138 linux,code = <28>;
139 wakeup-source;
140 };
141 };
142
143 i2c-gpio-0 {
144 status = "okay";
145 };
146};
1/*
2 * usb_a926x.dts - Device Tree file for Caloa USB A926x board
3 *
4 * Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
5 *
6 * Licensed under GPLv2 or later.
7 */
8
9/ {
10 clocks {
11 #address-cells = <1>;
12 #size-cells = <1>;
13 ranges;
14
15 main_clock: clock@0 {
16 compatible = "atmel,osc", "fixed-clock";
17 clock-frequency = <12000000>;
18 };
19 };
20
21 ahb {
22 apb {
23 dbgu: serial@fffff200 {
24 status = "okay";
25 };
26
27 macb0: ethernet@fffc4000 {
28 phy-mode = "rmii";
29 status = "okay";
30 };
31
32 usb1: gadget@fffa4000 {
33 atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
34 status = "okay";
35 };
36 };
37
38 nand0: nand@40000000 {
39 nand-bus-width = <8>;
40 nand-ecc-mode = "soft";
41 nand-on-flash-bbt;
42 status = "okay";
43
44 at91bootstrap@0 {
45 label = "at91bootstrap";
46 reg = <0x0 0x20000>;
47 };
48
49 barebox@20000 {
50 label = "barebox";
51 reg = <0x20000 0x40000>;
52 };
53
54 bareboxenv@60000 {
55 label = "bareboxenv";
56 reg = <0x60000 0x20000>;
57 };
58
59 bareboxenv2@80000 {
60 label = "bareboxenv2";
61 reg = <0x80000 0x20000>;
62 };
63
64 oftree@80000 {
65 label = "oftree";
66 reg = <0xa0000 0x20000>;
67 };
68
69 kernel@a0000 {
70 label = "kernel";
71 reg = <0xc0000 0x400000>;
72 };
73
74 rootfs@4a0000 {
75 label = "rootfs";
76 reg = <0x4c0000 0x7800000>;
77 };
78
79 data@7ca0000 {
80 label = "data";
81 reg = <0x7cc0000 0x8340000>;
82 };
83 };
84
85 usb0: ohci@00500000 {
86 num-ports = <2>;
87 status = "okay";
88 };
89 };
90
91 leds {
92 compatible = "gpio-leds";
93
94 user_led {
95 label = "user_led";
96 gpios = <&pioB 21 GPIO_ACTIVE_LOW>;
97 linux,default-trigger = "heartbeat";
98 };
99 };
100
101 gpio_keys {
102 compatible = "gpio-keys";
103 #address-cells = <1>;
104 #size-cells = <0>;
105
106 user_pb {
107 label = "user_pb";
108 gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
109 linux,code = <28>;
110 gpio-key,wakeup;
111 };
112 };
113
114 i2c@0 {
115 status = "okay";
116 };
117};