Loading...
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
4 */
5/dts-v1/;
6
7#include "dra74x.dtsi"
8#include "dra7-evm-common.dtsi"
9#include "dra74x-mmc-iodelay.dtsi"
10
11/ {
12 model = "TI DRA742";
13 compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7";
14
15 memory@0 {
16 device_type = "memory";
17 reg = <0x0 0x80000000 0x0 0x60000000>; /* 1536 MB */
18 };
19
20 evm_12v0: fixedregulator-evm_12v0 {
21 /* main supply */
22 compatible = "regulator-fixed";
23 regulator-name = "evm_12v0";
24 regulator-min-microvolt = <12000000>;
25 regulator-max-microvolt = <12000000>;
26 regulator-always-on;
27 regulator-boot-on;
28 };
29
30 evm_1v8_sw: fixedregulator-evm_1v8 {
31 compatible = "regulator-fixed";
32 regulator-name = "evm_1v8";
33 vin-supply = <&smps9_reg>;
34 regulator-min-microvolt = <1800000>;
35 regulator-max-microvolt = <1800000>;
36 };
37
38 evm_3v3_sd: fixedregulator-sd {
39 compatible = "regulator-fixed";
40 regulator-name = "evm_3v3_sd";
41 regulator-min-microvolt = <3300000>;
42 regulator-max-microvolt = <3300000>;
43 enable-active-high;
44 gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>;
45 };
46
47 evm_3v3_sw: fixedregulator-evm_3v3_sw {
48 compatible = "regulator-fixed";
49 regulator-name = "evm_3v3_sw";
50 vin-supply = <&sysen1>;
51 regulator-min-microvolt = <3300000>;
52 regulator-max-microvolt = <3300000>;
53 };
54
55 aic_dvdd: fixedregulator-aic_dvdd {
56 /* TPS77018DBVT */
57 compatible = "regulator-fixed";
58 regulator-name = "aic_dvdd";
59 vin-supply = <&evm_3v3_sw>;
60 regulator-min-microvolt = <1800000>;
61 regulator-max-microvolt = <1800000>;
62 };
63
64 evm_3v3: fixedregulator-evm3v3 {
65 /* Output of Cntlr A of TPS43351-Q1 on dra7-evm */
66 compatible = "regulator-fixed";
67 regulator-name = "evm_3v3";
68 regulator-min-microvolt = <3300000>;
69 regulator-max-microvolt = <3300000>;
70 vin-supply = <&evm_12v0>;
71 regulator-always-on;
72 regulator-boot-on;
73 };
74
75 evm_5v0: fixedregulator-evm_5v0 {
76 /* Output of Cntlr B of TPS43351-Q1 on dra7-evm */
77 compatible = "regulator-fixed";
78 regulator-name = "evm_5v0";
79 regulator-min-microvolt = <5000000>;
80 regulator-max-microvolt = <5000000>;
81 vin-supply = <&evm_12v0>;
82 regulator-always-on;
83 regulator-boot-on;
84 };
85
86 evm_3v6: fixedregulator-evm_3v6 {
87 compatible = "regulator-fixed";
88 regulator-name = "evm_3v6";
89 regulator-min-microvolt = <3600000>;
90 regulator-max-microvolt = <3600000>;
91 vin-supply = <&evm_5v0>;
92 regulator-always-on;
93 regulator-boot-on;
94 };
95
96 vmmcwl_fixed: fixedregulator-mmcwl {
97 compatible = "regulator-fixed";
98 regulator-name = "vmmcwl_fixed";
99 regulator-min-microvolt = <1800000>;
100 regulator-max-microvolt = <1800000>;
101 gpio = <&gpio5 8 0>;
102 startup-delay-us = <70000>;
103 enable-active-high;
104 };
105
106 vtt_fixed: fixedregulator-vtt {
107 compatible = "regulator-fixed";
108 regulator-name = "vtt_fixed";
109 regulator-min-microvolt = <1350000>;
110 regulator-max-microvolt = <1350000>;
111 regulator-always-on;
112 regulator-boot-on;
113 enable-active-high;
114 vin-supply = <&sysen2>;
115 gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
116 };
117
118};
119
120&dra7_pmx_core {
121 dcan1_pins_default: dcan1_pins_default {
122 pinctrl-single,pins = <
123 DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
124 DRA7XX_CORE_IOPAD(0x3818, PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */
125 >;
126 };
127
128 dcan1_pins_sleep: dcan1_pins_sleep {
129 pinctrl-single,pins = <
130 DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP) /* dcan1_tx.off */
131 DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */
132 >;
133 };
134};
135
136&i2c1 {
137 status = "okay";
138 clock-frequency = <400000>;
139
140 tps659038: tps659038@58 {
141 compatible = "ti,tps659038";
142 reg = <0x58>;
143 ti,palmas-override-powerhold;
144 ti,system-power-controller;
145
146 tps659038_pmic {
147 compatible = "ti,tps659038-pmic";
148
149 regulators {
150 smps123_reg: smps123 {
151 /* VDD_MPU */
152 regulator-name = "smps123";
153 regulator-min-microvolt = < 850000>;
154 regulator-max-microvolt = <1250000>;
155 regulator-always-on;
156 regulator-boot-on;
157 };
158
159 smps45_reg: smps45 {
160 /* VDD_DSPEVE */
161 regulator-name = "smps45";
162 regulator-min-microvolt = < 850000>;
163 regulator-max-microvolt = <1250000>;
164 regulator-always-on;
165 regulator-boot-on;
166 };
167
168 smps6_reg: smps6 {
169 /* VDD_GPU - over VDD_SMPS6 */
170 regulator-name = "smps6";
171 regulator-min-microvolt = <850000>;
172 regulator-max-microvolt = <1250000>;
173 regulator-always-on;
174 regulator-boot-on;
175 };
176
177 smps7_reg: smps7 {
178 /* CORE_VDD */
179 regulator-name = "smps7";
180 regulator-min-microvolt = <850000>;
181 regulator-max-microvolt = <1150000>;
182 regulator-always-on;
183 regulator-boot-on;
184 };
185
186 smps8_reg: smps8 {
187 /* VDD_IVAHD */
188 regulator-name = "smps8";
189 regulator-min-microvolt = < 850000>;
190 regulator-max-microvolt = <1250000>;
191 regulator-always-on;
192 regulator-boot-on;
193 };
194
195 smps9_reg: smps9 {
196 /* VDDS1V8 */
197 regulator-name = "smps9";
198 regulator-min-microvolt = <1800000>;
199 regulator-max-microvolt = <1800000>;
200 regulator-always-on;
201 regulator-boot-on;
202 };
203
204 ldo1_reg: ldo1 {
205 /* LDO1_OUT --> SDIO */
206 regulator-name = "ldo1";
207 regulator-min-microvolt = <1800000>;
208 regulator-max-microvolt = <3300000>;
209 regulator-always-on;
210 regulator-boot-on;
211 };
212
213 ldo2_reg: ldo2 {
214 /* VDD_RTCIO */
215 /* LDO2 -> VDDSHV5, LDO2 also goes to CAN_PHY_3V3 */
216 regulator-name = "ldo2";
217 regulator-min-microvolt = <3300000>;
218 regulator-max-microvolt = <3300000>;
219 regulator-always-on;
220 regulator-boot-on;
221 };
222
223 ldo3_reg: ldo3 {
224 /* VDDA_1V8_PHY */
225 regulator-name = "ldo3";
226 regulator-min-microvolt = <1800000>;
227 regulator-max-microvolt = <1800000>;
228 regulator-always-on;
229 regulator-boot-on;
230 };
231
232 ldo9_reg: ldo9 {
233 /* VDD_RTC */
234 regulator-name = "ldo9";
235 regulator-min-microvolt = <1050000>;
236 regulator-max-microvolt = <1050000>;
237 regulator-always-on;
238 regulator-boot-on;
239 regulator-allow-bypass;
240 };
241
242 ldoln_reg: ldoln {
243 /* VDDA_1V8_PLL */
244 regulator-name = "ldoln";
245 regulator-min-microvolt = <1800000>;
246 regulator-max-microvolt = <1800000>;
247 regulator-always-on;
248 regulator-boot-on;
249 };
250
251 ldousb_reg: ldousb {
252 /* VDDA_3V_USB: VDDA_USBHS33 */
253 regulator-name = "ldousb";
254 regulator-min-microvolt = <3300000>;
255 regulator-max-microvolt = <3300000>;
256 regulator-boot-on;
257 };
258
259 /* REGEN1 is unused */
260
261 regen2: regen2 {
262 /* Needed for PMIC internal resources */
263 regulator-name = "regen2";
264 regulator-boot-on;
265 regulator-always-on;
266 };
267
268 /* REGEN3 is unused */
269
270 sysen1: sysen1 {
271 /* PMIC_REGEN_3V3 */
272 regulator-name = "sysen1";
273 regulator-boot-on;
274 regulator-always-on;
275 };
276
277 sysen2: sysen2 {
278 /* PMIC_REGEN_DDR */
279 regulator-name = "sysen2";
280 regulator-boot-on;
281 regulator-always-on;
282 };
283 };
284 };
285 };
286
287 pcf_lcd: gpio@20 {
288 compatible = "ti,pcf8575", "nxp,pcf8575";
289 reg = <0x20>;
290 gpio-controller;
291 #gpio-cells = <2>;
292 interrupt-parent = <&gpio6>;
293 interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
294 interrupt-controller;
295 #interrupt-cells = <2>;
296 };
297
298 pcf_gpio_21: gpio@21 {
299 compatible = "ti,pcf8575", "nxp,pcf8575";
300 reg = <0x21>;
301 lines-initial-states = <0x1408>;
302 gpio-controller;
303 #gpio-cells = <2>;
304 interrupt-parent = <&gpio6>;
305 interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
306 interrupt-controller;
307 #interrupt-cells = <2>;
308 };
309
310 tlv320aic3106: tlv320aic3106@19 {
311 #sound-dai-cells = <0>;
312 compatible = "ti,tlv320aic3106";
313 reg = <0x19>;
314 adc-settle-ms = <40>;
315 ai3x-micbias-vg = <1>; /* 2.0V */
316 status = "okay";
317
318 /* Regulators */
319 AVDD-supply = <&evm_3v3_sw>;
320 IOVDD-supply = <&evm_3v3_sw>;
321 DRVDD-supply = <&evm_3v3_sw>;
322 DVDD-supply = <&aic_dvdd>;
323 };
324};
325
326&i2c2 {
327 status = "okay";
328 clock-frequency = <400000>;
329
330 pcf_hdmi: gpio@26 {
331 compatible = "ti,pcf8575", "nxp,pcf8575";
332 reg = <0x26>;
333 gpio-controller;
334 #gpio-cells = <2>;
335 p1 {
336 /* vin6_sel_s0: high: VIN6, low: audio */
337 gpio-hog;
338 gpios = <1 GPIO_ACTIVE_HIGH>;
339 output-low;
340 line-name = "vin6_sel_s0";
341 };
342 };
343};
344
345&mmc1 {
346 status = "okay";
347 vmmc-supply = <&evm_3v3_sd>;
348 vqmmc-supply = <&ldo1_reg>;
349 bus-width = <4>;
350 /*
351 * SDCD signal is not being used here - using the fact that GPIO mode
352 * is always hardwired.
353 */
354 cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
355 pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104";
356 pinctrl-0 = <&mmc1_pins_default>;
357 pinctrl-1 = <&mmc1_pins_hs>;
358 pinctrl-2 = <&mmc1_pins_sdr12>;
359 pinctrl-3 = <&mmc1_pins_sdr25>;
360 pinctrl-4 = <&mmc1_pins_sdr50>;
361 pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev11_conf>;
362 pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>;
363 pinctrl-7 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>;
364 pinctrl-8 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
365};
366
367&mmc2 {
368 status = "okay";
369 vmmc-supply = <&evm_1v8_sw>;
370 vqmmc-supply = <&evm_1v8_sw>;
371 bus-width = <8>;
372 non-removable;
373 pinctrl-names = "default", "hs", "ddr_1_8v-rev11", "ddr_1_8v", "hs200_1_8v-rev11", "hs200_1_8v";
374 pinctrl-0 = <&mmc2_pins_default>;
375 pinctrl-1 = <&mmc2_pins_hs>;
376 pinctrl-2 = <&mmc2_pins_ddr_1_8v_rev11 &mmc2_iodelay_ddr_1_8v_rev11_conf>;
377 pinctrl-3 = <&mmc2_pins_ddr_rev20>;
378 pinctrl-4 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev11_conf>;
379 pinctrl-5 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>;
380};
381
382&mmc4 {
383 status = "okay";
384 vmmc-supply = <&evm_3v6>;
385 vqmmc-supply = <&vmmcwl_fixed>;
386 pinctrl-names = "default-rev11", "default", "hs-rev11", "hs", "sdr12-rev11", "sdr12", "sdr25-rev11", "sdr25";
387 pinctrl-0 = <&mmc4_pins_default &mmc4_iodelay_ds_rev11_conf>;
388 pinctrl-1 = <&mmc4_pins_default &mmc4_iodelay_ds_rev20_conf>;
389 pinctrl-2 = <&mmc4_pins_hs &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>;
390 pinctrl-3 = <&mmc4_pins_hs &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>;
391 pinctrl-4 = <&mmc4_pins_sdr12 &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>;
392 pinctrl-5 = <&mmc4_pins_sdr12 &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>;
393 pinctrl-6 = <&mmc4_pins_sdr25 &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>;
394 pinctrl-7 = <&mmc4_pins_sdr25 &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>;
395};
396
397&cpu0 {
398 vdd-supply = <&smps123_reg>;
399};
400
401&elm {
402 status = "okay";
403};
404
405&gpmc {
406 /*
407 * For the existing IOdelay configuration via U-Boot we don't
408 * support NAND on dra7-evm. Keep it disabled. Enabling it
409 * requires a different configuration by U-Boot.
410 */
411 status = "disabled";
412 ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */
413 nand@0,0 {
414 compatible = "ti,omap2-nand";
415 reg = <0 0 4>; /* device IO registers */
416 interrupt-parent = <&gpmc>;
417 interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
418 <1 IRQ_TYPE_NONE>; /* termcount */
419 rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */
420 ti,nand-xfer-type = "prefetch-dma";
421 ti,nand-ecc-opt = "bch8";
422 ti,elm-id = <&elm>;
423 nand-bus-width = <16>;
424 gpmc,device-width = <2>;
425 gpmc,sync-clk-ps = <0>;
426 gpmc,cs-on-ns = <0>;
427 gpmc,cs-rd-off-ns = <80>;
428 gpmc,cs-wr-off-ns = <80>;
429 gpmc,adv-on-ns = <0>;
430 gpmc,adv-rd-off-ns = <60>;
431 gpmc,adv-wr-off-ns = <60>;
432 gpmc,we-on-ns = <10>;
433 gpmc,we-off-ns = <50>;
434 gpmc,oe-on-ns = <4>;
435 gpmc,oe-off-ns = <40>;
436 gpmc,access-ns = <40>;
437 gpmc,wr-access-ns = <80>;
438 gpmc,rd-cycle-ns = <80>;
439 gpmc,wr-cycle-ns = <80>;
440 gpmc,bus-turnaround-ns = <0>;
441 gpmc,cycle2cycle-delay-ns = <0>;
442 gpmc,clk-activation-ns = <0>;
443 gpmc,wr-data-mux-bus-ns = <0>;
444 /* MTD partition table */
445 /* All SPL-* partitions are sized to minimal length
446 * which can be independently programmable. For
447 * NAND flash this is equal to size of erase-block */
448 #address-cells = <1>;
449 #size-cells = <1>;
450 partition@0 {
451 label = "NAND.SPL";
452 reg = <0x00000000 0x000020000>;
453 };
454 partition@1 {
455 label = "NAND.SPL.backup1";
456 reg = <0x00020000 0x00020000>;
457 };
458 partition@2 {
459 label = "NAND.SPL.backup2";
460 reg = <0x00040000 0x00020000>;
461 };
462 partition@3 {
463 label = "NAND.SPL.backup3";
464 reg = <0x00060000 0x00020000>;
465 };
466 partition@4 {
467 label = "NAND.u-boot-spl-os";
468 reg = <0x00080000 0x00040000>;
469 };
470 partition@5 {
471 label = "NAND.u-boot";
472 reg = <0x000c0000 0x00100000>;
473 };
474 partition@6 {
475 label = "NAND.u-boot-env";
476 reg = <0x001c0000 0x00020000>;
477 };
478 partition@7 {
479 label = "NAND.u-boot-env.backup1";
480 reg = <0x001e0000 0x00020000>;
481 };
482 partition@8 {
483 label = "NAND.kernel";
484 reg = <0x00200000 0x00800000>;
485 };
486 partition@9 {
487 label = "NAND.file-system";
488 reg = <0x00a00000 0x0f600000>;
489 };
490 };
491};
492
493&usb2_phy1 {
494 phy-supply = <&ldousb_reg>;
495};
496
497&usb2_phy2 {
498 phy-supply = <&ldousb_reg>;
499};
500
501&gpio7_target {
502 ti,no-reset-on-init;
503 ti,no-idle-on-init;
504};
505
506&mac {
507 status = "okay";
508 dual_emac;
509};
510
511&cpsw_emac0 {
512 phy-handle = <ðphy0>;
513 phy-mode = "rgmii";
514 dual_emac_res_vlan = <1>;
515};
516
517&cpsw_emac1 {
518 phy-handle = <ðphy1>;
519 phy-mode = "rgmii";
520 dual_emac_res_vlan = <2>;
521};
522
523&davinci_mdio {
524 ethphy0: ethernet-phy@2 {
525 reg = <2>;
526 };
527
528 ethphy1: ethernet-phy@3 {
529 reg = <3>;
530 };
531};
532
533&dcan1 {
534 status = "ok";
535 pinctrl-names = "default", "sleep", "active";
536 pinctrl-0 = <&dcan1_pins_sleep>;
537 pinctrl-1 = <&dcan1_pins_sleep>;
538 pinctrl-2 = <&dcan1_pins_default>;
539};
1/*
2 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
3 *
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
7 */
8/dts-v1/;
9
10#include "dra7.dtsi"
11
12/ {
13 model = "TI DRA7";
14 compatible = "ti,dra7-evm", "ti,dra752", "ti,dra7";
15
16 memory {
17 device_type = "memory";
18 reg = <0x80000000 0x60000000>; /* 1536 MB */
19 };
20
21 mmc2_3v3: fixedregulator-mmc2 {
22 compatible = "regulator-fixed";
23 regulator-name = "mmc2_3v3";
24 regulator-min-microvolt = <3300000>;
25 regulator-max-microvolt = <3300000>;
26 };
27};
28
29&dra7_pmx_core {
30 i2c1_pins: pinmux_i2c1_pins {
31 pinctrl-single,pins = <
32 0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda */
33 0x404 (PIN_INPUT | MUX_MODE0) /* i2c1_scl */
34 >;
35 };
36
37 i2c2_pins: pinmux_i2c2_pins {
38 pinctrl-single,pins = <
39 0x408 (PIN_INPUT | MUX_MODE0) /* i2c2_sda */
40 0x40c (PIN_INPUT | MUX_MODE0) /* i2c2_scl */
41 >;
42 };
43
44 i2c3_pins: pinmux_i2c3_pins {
45 pinctrl-single,pins = <
46 0x410 (PIN_INPUT | MUX_MODE0) /* i2c3_sda */
47 0x414 (PIN_INPUT | MUX_MODE0) /* i2c3_scl */
48 >;
49 };
50
51 mcspi1_pins: pinmux_mcspi1_pins {
52 pinctrl-single,pins = <
53 0x3a4 (PIN_INPUT | MUX_MODE0) /* spi2_clk */
54 0x3a8 (PIN_INPUT | MUX_MODE0) /* spi2_d1 */
55 0x3ac (PIN_INPUT | MUX_MODE0) /* spi2_d0 */
56 0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
57 0x3b4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs1 */
58 0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs2 */
59 0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs3 */
60 >;
61 };
62
63 mcspi2_pins: pinmux_mcspi2_pins {
64 pinctrl-single,pins = <
65 0x3c0 (PIN_INPUT | MUX_MODE0) /* spi2_sclk */
66 0x3c4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
67 0x3c8 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
68 0x3cc (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
69 >;
70 };
71
72 uart1_pins: pinmux_uart1_pins {
73 pinctrl-single,pins = <
74 0x3e0 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_rxd */
75 0x3e4 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_txd */
76 0x3e8 (PIN_INPUT | MUX_MODE3) /* uart1_ctsn */
77 0x3ec (PIN_INPUT | MUX_MODE3) /* uart1_rtsn */
78 >;
79 };
80
81 uart2_pins: pinmux_uart2_pins {
82 pinctrl-single,pins = <
83 0x3f0 (PIN_INPUT | MUX_MODE0) /* uart2_rxd */
84 0x3f4 (PIN_INPUT | MUX_MODE0) /* uart2_txd */
85 0x3f8 (PIN_INPUT | MUX_MODE0) /* uart2_ctsn */
86 0x3fc (PIN_INPUT | MUX_MODE0) /* uart2_rtsn */
87 >;
88 };
89
90 uart3_pins: pinmux_uart3_pins {
91 pinctrl-single,pins = <
92 0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */
93 0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */
94 >;
95 };
96};
97
98&i2c1 {
99 status = "okay";
100 pinctrl-names = "default";
101 pinctrl-0 = <&i2c1_pins>;
102 clock-frequency = <400000>;
103
104 tps659038: tps659038@58 {
105 compatible = "ti,tps659038";
106 reg = <0x58>;
107
108 tps659038_pmic {
109 compatible = "ti,tps659038-pmic";
110
111 regulators {
112 smps123_reg: smps123 {
113 /* VDD_MPU */
114 regulator-name = "smps123";
115 regulator-min-microvolt = < 850000>;
116 regulator-max-microvolt = <1250000>;
117 regulator-always-on;
118 regulator-boot-on;
119 };
120
121 smps45_reg: smps45 {
122 /* VDD_DSPEVE */
123 regulator-name = "smps45";
124 regulator-min-microvolt = < 850000>;
125 regulator-max-microvolt = <1150000>;
126 regulator-boot-on;
127 };
128
129 smps6_reg: smps6 {
130 /* VDD_GPU - over VDD_SMPS6 */
131 regulator-name = "smps6";
132 regulator-min-microvolt = <850000>;
133 regulator-max-microvolt = <12500000>;
134 regulator-boot-on;
135 };
136
137 smps7_reg: smps7 {
138 /* CORE_VDD */
139 regulator-name = "smps7";
140 regulator-min-microvolt = <850000>;
141 regulator-max-microvolt = <1030000>;
142 regulator-always-on;
143 regulator-boot-on;
144 };
145
146 smps8_reg: smps8 {
147 /* VDD_IVAHD */
148 regulator-name = "smps8";
149 regulator-min-microvolt = < 850000>;
150 regulator-max-microvolt = <1250000>;
151 regulator-boot-on;
152 };
153
154 smps9_reg: smps9 {
155 /* VDDS1V8 */
156 regulator-name = "smps9";
157 regulator-min-microvolt = <1800000>;
158 regulator-max-microvolt = <1800000>;
159 regulator-always-on;
160 regulator-boot-on;
161 };
162
163 ldo1_reg: ldo1 {
164 /* LDO1_OUT --> SDIO */
165 regulator-name = "ldo1";
166 regulator-min-microvolt = <1800000>;
167 regulator-max-microvolt = <3300000>;
168 regulator-boot-on;
169 };
170
171 ldo2_reg: ldo2 {
172 /* VDD_RTCIO */
173 /* LDO2 -> VDDSHV5, LDO2 also goes to CAN_PHY_3V3 */
174 regulator-name = "ldo2";
175 regulator-min-microvolt = <3300000>;
176 regulator-max-microvolt = <3300000>;
177 regulator-boot-on;
178 };
179
180 ldo3_reg: ldo3 {
181 /* VDDA_1V8_PHY */
182 regulator-name = "ldo3";
183 regulator-min-microvolt = <1800000>;
184 regulator-max-microvolt = <1800000>;
185 regulator-boot-on;
186 };
187
188 ldo9_reg: ldo9 {
189 /* VDD_RTC */
190 regulator-name = "ldo9";
191 regulator-min-microvolt = <1050000>;
192 regulator-max-microvolt = <1050000>;
193 regulator-boot-on;
194 };
195
196 ldoln_reg: ldoln {
197 /* VDDA_1V8_PLL */
198 regulator-name = "ldoln";
199 regulator-min-microvolt = <1800000>;
200 regulator-max-microvolt = <1800000>;
201 regulator-always-on;
202 regulator-boot-on;
203 };
204
205 ldousb_reg: ldousb {
206 /* VDDA_3V_USB: VDDA_USBHS33 */
207 regulator-name = "ldousb";
208 regulator-min-microvolt = <3300000>;
209 regulator-max-microvolt = <3300000>;
210 regulator-boot-on;
211 };
212 };
213 };
214 };
215};
216
217&i2c2 {
218 status = "okay";
219 pinctrl-names = "default";
220 pinctrl-0 = <&i2c2_pins>;
221 clock-frequency = <400000>;
222};
223
224&i2c3 {
225 status = "okay";
226 pinctrl-names = "default";
227 pinctrl-0 = <&i2c3_pins>;
228 clock-frequency = <3400000>;
229};
230
231&mcspi1 {
232 status = "okay";
233 pinctrl-names = "default";
234 pinctrl-0 = <&mcspi1_pins>;
235};
236
237&mcspi2 {
238 status = "okay";
239 pinctrl-names = "default";
240 pinctrl-0 = <&mcspi2_pins>;
241};
242
243&uart1 {
244 status = "okay";
245 pinctrl-names = "default";
246 pinctrl-0 = <&uart1_pins>;
247};
248
249&uart2 {
250 status = "okay";
251 pinctrl-names = "default";
252 pinctrl-0 = <&uart2_pins>;
253};
254
255&uart3 {
256 status = "okay";
257 pinctrl-names = "default";
258 pinctrl-0 = <&uart3_pins>;
259};
260
261&mmc1 {
262 status = "okay";
263 vmmc-supply = <&ldo1_reg>;
264 bus-width = <4>;
265};
266
267&mmc2 {
268 status = "okay";
269 vmmc-supply = <&mmc2_3v3>;
270 bus-width = <8>;
271};
272
273&cpu0 {
274 cpu0-supply = <&smps123_reg>;
275};