Loading...
1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2/*
3 * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
4 *
5 * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
6 * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
7 */
8
9/dts-v1/;
10#include "sun8i-h3.dtsi"
11#include "sunxi-common-regulators.dtsi"
12
13#include <dt-bindings/gpio/gpio.h>
14#include <dt-bindings/input/input.h>
15
16/ {
17 model = "Banana Pi BPI-M2-Zero";
18 compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
19
20 aliases {
21 serial0 = &uart0;
22 serial1 = &uart1;
23 };
24
25 chosen {
26 stdout-path = "serial0:115200n8";
27 };
28
29 connector {
30 compatible = "hdmi-connector";
31 type = "c";
32
33 port {
34 hdmi_con_in: endpoint {
35 remote-endpoint = <&hdmi_out_con>;
36 };
37 };
38 };
39
40 leds {
41 compatible = "gpio-leds";
42
43 pwr_led {
44 label = "bananapi-m2-zero:red:pwr";
45 gpios = <&r_pio 0 10 GPIO_ACTIVE_LOW>; /* PL10 */
46 default-state = "on";
47 };
48 };
49
50 gpio_keys {
51 compatible = "gpio-keys";
52
53 sw4 {
54 label = "power";
55 linux,code = <BTN_0>;
56 gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
57 };
58 };
59
60 reg_vdd_cpux: vdd-cpux-regulator {
61 compatible = "regulator-gpio";
62 regulator-name = "vdd-cpux";
63 regulator-type = "voltage";
64 regulator-boot-on;
65 regulator-always-on;
66 regulator-min-microvolt = <1100000>;
67 regulator-max-microvolt = <1300000>;
68 regulator-ramp-delay = <50>; /* 4ms */
69
70 gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
71 enable-active-high;
72 gpios-states = <0x1>;
73 states = <1100000 0>, <1300000 1>;
74 };
75
76 reg_vcc_dram: vcc-dram {
77 compatible = "regulator-fixed";
78 regulator-name = "vcc-dram";
79 regulator-min-microvolt = <1500000>;
80 regulator-max-microvolt = <1500000>;
81 regulator-always-on;
82 regulator-boot-on;
83 enable-active-high;
84 gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
85 vin-supply = <®_vcc5v0>;
86 };
87
88 reg_vcc1v2: vcc1v2 {
89 compatible = "regulator-fixed";
90 regulator-name = "vcc1v2";
91 regulator-min-microvolt = <1200000>;
92 regulator-max-microvolt = <1200000>;
93 regulator-always-on;
94 regulator-boot-on;
95 enable-active-high;
96 gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
97 vin-supply = <®_vcc5v0>;
98 };
99
100 poweroff {
101 compatible = "regulator-poweroff";
102 cpu-supply = <®_vcc1v2>;
103 };
104
105 wifi_pwrseq: wifi_pwrseq {
106 compatible = "mmc-pwrseq-simple";
107 reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
108 clocks = <&rtc 1>;
109 clock-names = "ext_clock";
110 };
111};
112
113&cpu0 {
114 cpu-supply = <®_vdd_cpux>;
115};
116
117&de {
118 status = "okay";
119};
120
121&ehci0 {
122 status = "okay";
123};
124
125&hdmi {
126 status = "okay";
127};
128
129&hdmi_out {
130 hdmi_out_con: endpoint {
131 remote-endpoint = <&hdmi_con_in>;
132 };
133};
134
135&mmc0 {
136 vmmc-supply = <®_vcc3v3>;
137 bus-width = <4>;
138 /*
139 * On the production batch of this board the card detect GPIO is
140 * high active (card inserted), although on the early samples it's
141 * low active.
142 */
143 cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
144 status = "okay";
145};
146
147&mmc1 {
148 vmmc-supply = <®_vcc3v3>;
149 vqmmc-supply = <®_vcc3v3>;
150 mmc-pwrseq = <&wifi_pwrseq>;
151 bus-width = <4>;
152 non-removable;
153 status = "okay";
154
155 brcmf: wifi@1 {
156 reg = <1>;
157 compatible = "brcm,bcm4329-fmac";
158 interrupt-parent = <&pio>;
159 interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
160 interrupt-names = "host-wake";
161 };
162};
163
164&ohci0 {
165 status = "okay";
166};
167
168&uart0 {
169 pinctrl-names = "default";
170 pinctrl-0 = <&uart0_pa_pins>;
171 status = "okay";
172};
173
174&uart1 {
175 pinctrl-names = "default";
176 pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
177 uart-has-rtscts;
178 status = "okay";
179
180 bluetooth {
181 compatible = "brcm,bcm43438-bt";
182 max-speed = <1500000>;
183 clocks = <&rtc 1>;
184 clock-names = "lpo";
185 vbat-supply = <®_vcc3v3>;
186 vddio-supply = <®_vcc3v3>;
187 device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
188 host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
189 shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
190 };
191
192};
193
194&pio {
195 gpio-line-names =
196 /* PA */
197 "CON2-P13", "CON2-P11", "CON2-P22", "CON2-P15",
198 "CON3-P03", "CON3-P02", "CON2-P07", "CON2-P29",
199 "CON2-P31", "CON2-P33", "CON2-P35", "CON2-P05",
200 "CON2-P03", "CON2-P08", "CON2-P10", "CON2-P16",
201 "CON2-P12", "CON2-P37", "CON2-P28", "CON2-P27",
202 "CON2-P40", "CON2-P38", "", "",
203 "", "", "", "", "", "", "", "",
204
205 /* PB */
206 "", "", "", "", "", "", "", "",
207 "", "", "", "", "", "", "", "",
208 "", "", "", "", "", "", "", "",
209 "", "", "", "", "", "", "", "",
210
211 /* PC */
212 "CON2-P19", "CON2-P21", "CON2-P23", "CON2-P24",
213 "CON2-P18", "", "", "CON2-P26",
214 "", "", "", "", "", "", "", "",
215 "", "", "", "", "", "", "", "",
216 "", "", "", "", "", "", "", "",
217
218 /* PD */
219 "", "", "", "", "", "", "", "",
220 "", "", "", "", "", "", "CSI-PWR-EN", "",
221 "", "", "", "", "", "", "", "",
222 "", "", "", "", "", "", "", "",
223
224 /* PE */
225 "CN3-P17", "CN3-P13", "CN3-P09", "CN3-P07",
226 "CN3-P19", "CN3-P21", "CN3-P22", "CN3-P20",
227 "CN3-P18", "CN3-P16", "CN3-P14", "CN3-P12",
228 "CN3-P05", "CN3-P03", "CN3-P06", "CN3-P08",
229 "", "", "", "", "", "", "", "",
230 "", "", "", "", "", "", "", "",
231
232 /* PF */
233 "SDC0-D1", "SDC0-D0", "SDC0-CLK", "SDC0-CMD", "SDC0-D3",
234 "SDC0-D2", "SDC0-DET", "",
235 "", "", "", "", "", "", "", "",
236 "", "", "", "", "", "", "", "",
237 "", "", "", "", "", "", "", "",
238
239 /* PG */
240 "WL-SDIO-CLK", "WL-SDIO-CMD", "WL-SDIO-D0", "WL-SDIO-D1",
241 "WL-SDIO-D2", "WL-SDIO-D3", "BT-UART-TX", "BT-UART-RX",
242 "BT-UART-RTS", "BT-UART-CTS", "WL-WAKE-AP", "BT-WAKE-AP",
243 "BT-RST-N", "AP-WAKE-BT", "", "",
244 "", "", "", "", "", "", "", "",
245 "", "", "", "", "", "", "", "";
246};
247
248&r_pio {
249 gpio-line-names =
250 /* PL */
251 "", "CPUX-SET", "CON2-P32", "POWER-KEY", "CON2-P36",
252 "VCC-IO-EN", "USB0-ID", "WL-PWR-EN",
253 "PWR-STB", "PWR-DRAM", "PWR-LED", "IR-RX", "", "", "", "",
254 "", "", "", "", "", "", "", "",
255 "", "", "", "", "", "", "", "";
256};
257
258&usb_otg {
259 dr_mode = "otg";
260 status = "okay";
261};
262
263&usbphy {
264 usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
265 /*
266 * There're two micro-USB connectors, one is power-only and another is
267 * OTG. The Vbus of these two connectors are connected together, so
268 * the external USB device will be powered just by the power input
269 * from the power-only USB port.
270 */
271 status = "okay";
272};
1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2/*
3 * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
4 *
5 * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
6 * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
7 */
8
9/dts-v1/;
10#include "sun8i-h3.dtsi"
11#include "sunxi-common-regulators.dtsi"
12
13#include <dt-bindings/gpio/gpio.h>
14#include <dt-bindings/input/input.h>
15
16/ {
17 model = "Banana Pi BPI-M2-Zero";
18 compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
19
20 aliases {
21 serial0 = &uart0;
22 serial1 = &uart1;
23 };
24
25 chosen {
26 stdout-path = "serial0:115200n8";
27 };
28
29 connector {
30 compatible = "hdmi-connector";
31 type = "c";
32
33 port {
34 hdmi_con_in: endpoint {
35 remote-endpoint = <&hdmi_out_con>;
36 };
37 };
38 };
39
40 leds {
41 compatible = "gpio-leds";
42
43 pwr_led {
44 label = "bananapi-m2-zero:red:pwr";
45 gpios = <&r_pio 0 10 GPIO_ACTIVE_LOW>; /* PL10 */
46 default-state = "on";
47 };
48 };
49
50 gpio-keys {
51 compatible = "gpio-keys";
52
53 switch-4 {
54 label = "power";
55 linux,code = <KEY_POWER>;
56 gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
57 wakeup-source;
58 };
59 };
60
61 reg_vdd_cpux: vdd-cpux-regulator {
62 compatible = "regulator-gpio";
63 regulator-name = "vdd-cpux";
64 regulator-type = "voltage";
65 regulator-boot-on;
66 regulator-always-on;
67 regulator-min-microvolt = <1100000>;
68 regulator-max-microvolt = <1300000>;
69 regulator-ramp-delay = <50>; /* 4ms */
70
71 gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
72 enable-active-high;
73 gpios-states = <0x1>;
74 states = <1100000 0>, <1300000 1>;
75 };
76
77 reg_vcc_dram: vcc-dram {
78 compatible = "regulator-fixed";
79 regulator-name = "vcc-dram";
80 regulator-min-microvolt = <1500000>;
81 regulator-max-microvolt = <1500000>;
82 regulator-always-on;
83 regulator-boot-on;
84 enable-active-high;
85 gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
86 vin-supply = <®_vcc5v0>;
87 };
88
89 reg_vcc1v2: vcc1v2 {
90 compatible = "regulator-fixed";
91 regulator-name = "vcc1v2";
92 regulator-min-microvolt = <1200000>;
93 regulator-max-microvolt = <1200000>;
94 regulator-always-on;
95 regulator-boot-on;
96 enable-active-high;
97 gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
98 vin-supply = <®_vcc5v0>;
99 };
100
101 poweroff {
102 compatible = "regulator-poweroff";
103 cpu-supply = <®_vcc1v2>;
104 };
105
106 wifi_pwrseq: wifi_pwrseq {
107 compatible = "mmc-pwrseq-simple";
108 reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
109 clocks = <&rtc CLK_OSC32K_FANOUT>;
110 clock-names = "ext_clock";
111 };
112};
113
114&cpu0 {
115 cpu-supply = <®_vdd_cpux>;
116};
117
118&de {
119 status = "okay";
120};
121
122&ehci0 {
123 status = "okay";
124};
125
126&hdmi {
127 status = "okay";
128};
129
130&hdmi_out {
131 hdmi_out_con: endpoint {
132 remote-endpoint = <&hdmi_con_in>;
133 };
134};
135
136&mmc0 {
137 vmmc-supply = <®_vcc3v3>;
138 bus-width = <4>;
139 /*
140 * On the production batch of this board the card detect GPIO is
141 * high active (card inserted), although on the early samples it's
142 * low active.
143 */
144 cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
145 status = "okay";
146};
147
148&mmc1 {
149 vmmc-supply = <®_vcc3v3>;
150 vqmmc-supply = <®_vcc3v3>;
151 mmc-pwrseq = <&wifi_pwrseq>;
152 bus-width = <4>;
153 non-removable;
154 status = "okay";
155
156 brcmf: wifi@1 {
157 reg = <1>;
158 compatible = "brcm,bcm4329-fmac";
159 interrupt-parent = <&pio>;
160 interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
161 interrupt-names = "host-wake";
162 };
163};
164
165&ohci0 {
166 status = "okay";
167};
168
169&uart0 {
170 pinctrl-names = "default";
171 pinctrl-0 = <&uart0_pa_pins>;
172 status = "okay";
173};
174
175&uart1 {
176 pinctrl-names = "default";
177 pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
178 uart-has-rtscts;
179 status = "okay";
180
181 bluetooth {
182 compatible = "brcm,bcm43438-bt";
183 max-speed = <1500000>;
184 clocks = <&rtc CLK_OSC32K_FANOUT>;
185 clock-names = "lpo";
186 vbat-supply = <®_vcc3v3>;
187 vddio-supply = <®_vcc3v3>;
188 device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
189 host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
190 shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
191 };
192
193};
194
195&pio {
196 gpio-line-names =
197 /* PA */
198 "CON2-P13", "CON2-P11", "CON2-P22", "CON2-P15",
199 "CON3-P03", "CON3-P02", "CON2-P07", "CON2-P29",
200 "CON2-P31", "CON2-P33", "CON2-P35", "CON2-P05",
201 "CON2-P03", "CON2-P08", "CON2-P10", "CON2-P16",
202 "CON2-P12", "CON2-P37", "CON2-P28", "CON2-P27",
203 "CON2-P40", "CON2-P38", "", "",
204 "", "", "", "", "", "", "", "",
205
206 /* PB */
207 "", "", "", "", "", "", "", "",
208 "", "", "", "", "", "", "", "",
209 "", "", "", "", "", "", "", "",
210 "", "", "", "", "", "", "", "",
211
212 /* PC */
213 "CON2-P19", "CON2-P21", "CON2-P23", "CON2-P24",
214 "CON2-P18", "", "", "CON2-P26",
215 "", "", "", "", "", "", "", "",
216 "", "", "", "", "", "", "", "",
217 "", "", "", "", "", "", "", "",
218
219 /* PD */
220 "", "", "", "", "", "", "", "",
221 "", "", "", "", "", "", "CSI-PWR-EN", "",
222 "", "", "", "", "", "", "", "",
223 "", "", "", "", "", "", "", "",
224
225 /* PE */
226 "CN3-P17", "CN3-P13", "CN3-P09", "CN3-P07",
227 "CN3-P19", "CN3-P21", "CN3-P22", "CN3-P20",
228 "CN3-P18", "CN3-P16", "CN3-P14", "CN3-P12",
229 "CN3-P05", "CN3-P03", "CN3-P06", "CN3-P08",
230 "", "", "", "", "", "", "", "",
231 "", "", "", "", "", "", "", "",
232
233 /* PF */
234 "SDC0-D1", "SDC0-D0", "SDC0-CLK", "SDC0-CMD", "SDC0-D3",
235 "SDC0-D2", "SDC0-DET", "",
236 "", "", "", "", "", "", "", "",
237 "", "", "", "", "", "", "", "",
238 "", "", "", "", "", "", "", "",
239
240 /* PG */
241 "WL-SDIO-CLK", "WL-SDIO-CMD", "WL-SDIO-D0", "WL-SDIO-D1",
242 "WL-SDIO-D2", "WL-SDIO-D3", "BT-UART-TX", "BT-UART-RX",
243 "BT-UART-RTS", "BT-UART-CTS", "WL-WAKE-AP", "BT-WAKE-AP",
244 "BT-RST-N", "AP-WAKE-BT", "", "",
245 "", "", "", "", "", "", "", "",
246 "", "", "", "", "", "", "", "";
247};
248
249&r_pio {
250 gpio-line-names =
251 /* PL */
252 "", "CPUX-SET", "CON2-P32", "POWER-KEY", "CON2-P36",
253 "VCC-IO-EN", "USB0-ID", "WL-PWR-EN",
254 "PWR-STB", "PWR-DRAM", "PWR-LED", "IR-RX", "", "", "", "",
255 "", "", "", "", "", "", "", "",
256 "", "", "", "", "", "", "", "";
257};
258
259&usb_otg {
260 dr_mode = "otg";
261 status = "okay";
262};
263
264&usbphy {
265 usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
266 /*
267 * There're two micro-USB connectors, one is power-only and another is
268 * OTG. The Vbus of these two connectors are connected together, so
269 * the external USB device will be powered just by the power input
270 * from the power-only USB port.
271 */
272 status = "okay";
273};